An experimental ultra wideband ground penetrating radar based on Golay complementary sequences is proposed to locate underground pipes. Golay complementary sequences with the code length of 1024 and frequency of 1 GHz are used as the probe signals. Two-dimensional image of the buried pipes is achieved by correlation method and back projection algorithm. The experimental results show that both the plastic pipe and metallic pipe can be located with a range resolution of 10 cm. Furthermore, as the Golay complementary sequences are a pair of complementary sequences, the sum of their correlation function yields twice the value of the peak at the target position and zero elsewhere. Thus, compared with the stepped frequency signal radar or chaotic signal radar, the Golay-based radar can significantly improve the signal noise ratio and has capability of deep detection.

The real systems are often complex, nonlinear, and noisy in various areas including mathematics, natural science, and social science. We present the symplectic entropy (SymEn) measure as well as an analysis method based on SymEn to estimate the nonlinearity of the complex system by analyzing the given time series. The SymEn estimation is a kind of entropy based on symplectic principal component analysis (SPCA) which represent organized but unpredictable behaviors of systems. The key to SPCA is to preserve the global submanifold geometrical properties of the systems through symplectic transform in the phase space, which is a kind of the measure-preserving transforms. The capability of preserving the global geometrical characteristics makes the SymEn a test statistic to detect the nonlinear characteristics in several typical chaotic time series and the stochastic characteristic in the Gaussian white noise. The results are in agreement with findings in the approximate entropy (ApEn), the sample entropy (SampEn) and the fuzzy entropy (FuzzyEn). Moreover, the SymEn method is also used to analyze the nonlinearities of the real signals (including the EEG signals for ASD and healthy subjects, and the sound and vibration signals for the mechanical systems). The results indicate that the SymEn estimation can be taken as a measure for describing the nonlinear characteristics in the data collected from the natural complex systems.

The success of deep learning (DL) in offline brain-computer interfaces (BCIs) has not yet translated into efficient online applications. This is due to three primary challenges. First, most DL solutions are designed for offline decoding, making the transition to online decoding complex and unclear. Second, the use of sliding windows in online decoding increases the computational complexity of DL training. Third, DL models typically require large amounts of training data, which are often scarce in BCI applications. To address these issues and enable real-time decoding, even across different subjects without calibration data, we first introduce a novel approach called real-time adaptive pooling (RAP). RAP modifies the pooling layers of existing offline DL models towards the online decoding requirements. Additionally, it significantly reduces the computational demand during training by jointly decoding consecutive windows. To reduce the amount of training data required, our approach leverages different levels of domain adaptation. We show how different settings enable different adaptation solutions. The results demonstrate that our approach is both powerful and can be calibration-free, providing a robust and practical solution for real-time BCI applications. These findings pave the way for the development of co-adaptive and highly efficient DL-based online BCI systems.

The paper addresses the energy consumption minimization problem in wireless powered communication networks (WPCNs) and proposes a DT-SWIPT-assisted time allocation scheme, named DaTA, such that the wireless station can share the remaining energy after transmission to the HAP to those who have not transmitted to the HAP to minimize the energy consumption of the network. In addition to proposing a new frame structure, the paper also considers the SNR (Signal-to-Noise) constraint to guarantee that the HAP can successfully receive data from wireless stations. In the paper, the energy consumption minimization problem is formulated as a nonlinear programming model. We employ the SQP (Sequential Quadratic Programming) algorithm to figure out the optimal solution. Moreover, a heuristic method is proposed as well to obtain a near-optimal solution in a shorter time. Simulation results showed that the proposed scheme can have better performance than the related work in terms of energy consumption and energy efficiency.

Against the background of the sky, imaging and perception of aircraft are cru- cial. Among these, the location of aircrafts is not a very difficult problem in general, because that deep learning algorithms and object detection models based on convolutional neural network(CNN) are ever-evolving. In order to have a better identification of various aircrafts, or to accurately locate different types of flying targets in the sky, it becomes significant to distinguish and recognize different types of aircrafts. One question is that, distinguishing and recognizing between sub-categories of aircrafts pose great challenges. Although fine-grained recognition focuses on exploring and studying such problems, aircrafts under different sub-categories and granularities lead us to rethink the application of features. We noticed that features in swin-transformer demonstrates the under- standing and processing of images, fully showcasing the encoding and indexing of information. Through this research and proposed approach, we discovered a better understanding of features encoding and use, which are inspired by the feature encoding and computation in swin-transformer. In our paper, our ap- proach has achieved effects on features encoded graphically, manifested from the architecture design and convolutional neural network computation, and outper- forms other famous fine-graiend classification models on this issue. Not only approach we proposed has demonstrated superior performance in fine-grained aicraft classification, but also the mechanisms of the feature encoding under different sample space partitions is revealed for this issue, which provides a re- search for the representation of aircraft fineness characteristics. The relationship between representation orientation of aircraft feature information under various grained divisions, shows that the recognition of different categories according to man-made, such as aircraft, can be achieved by means of the feature represen- tations studied in this paper, for more specific defined classification tasks and various man-made targets partition criteria, which may influences the princi- ple of design for calculation and feature extraction in fine-grained classification models.

Intelligent fault diagnosis techniques have replaced the time-consuming and unreliable human analysis, increasing the efficiency of fault diagnosis. Deep learning model can improve the accuracy of intelligent fault diagnosis with the help of its multilayer nonlinear mapping ability. This paper has proposed a novel method named Deep Convolutional Neural Networks with Wide First-layer Kernels (WDCNN). The proposed method uses raw vibration signals as input (data augmentation is used to generate more inputs), and uses the wide kernels in first convolutional layer for extracting feature and suppressing high frequency noise. Small convolutional kernels in the preceding layers are used for multilayer nonlinear mapping. AdaBN is implemented to improve the domain adaptation ability of the model. The proposed model addresses the problem that currently, the accuracy of CNN applied to fault diagnosis is not very high. WDCNN can not only achieve 100% classification accuracy on normal signals, but also outperform state of the art DNN model which is based on frequency features under different working load and noisy environment.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Diffusion magnetic resonance imaging (dMRI) is an imaging technique that provides information on the microstructural organization of biological tissue. dMRI allows for non-invasive visualization and quantitative assessment of white matter architecture in the brain by characterizing restrictions on the random motion of water molecules. Ultra-high field MRI scanners, such as those operating at 7 Tesla (7T) or higher, can boost signal-to-noise ratio (SNR) to improve dMRI compared with what is attainable at conventional field strengths such as 3T or 1.5T. However, at 7T wavelength effects cause lower transmit magnetic field efficiency in the human brain, mainly in the posterior fossa region, manifesting as signal dropouts in this region. Recently, we reported a simple approach of using a wireless radiofrequency (RF) surface array to improve transmit efficiency and signal sensitivity at 7T. Here we demonstrate the feasibility and effectiveness of using this RF enhancer for in-vivo dMRI at 7T. The use of the RF enhancer can effectively recover signal dropouts in the regions with intrinsically lower SNR such as cerebellum, leading to a better depiction of principal fiber orientations and enhanced visualization of extended tracts to the brainstem and pons enabling more comprehensive delineation of the full white matter architecture.

Characterization of flying insects in-situ measurement using remote sensing spectroscopy is an emerging research field. Also, most analysis techniques in remote sensing spectroscopy are based on the use of an intensity threshold which introduces indeterminacies in the number of detected specimens. In this manuscript, we investigated the possibility of analysing passive remote sensing spectroscopy measurement data using the maximum noise fraction method. The results obtained show that this analysis technique can help to overcome the measurement of background noise in spectroscopic measurements.

Target recognition mainly includes three approaches: optical image-based, echo detection-based, and passive signal analysis-based methods. Among them, the passive signal-based method is closely integrated with practical applications due to its strong environmental adaptability. Based on passive radar signal analysis, we design an "end-to-end" model that cascades a noise estimation network with a recognition network to identify working modes in noise environment. The noise estimation network is implemented based on U-Net, which adopts a method of feature extraction and reconstruction to adaptively estimate the noise mapping level of the sample, which can help the recognition network to reduce noise interference. Focusing on the characteristics of radar signal, the recognition network is realized based on Multi-Scale Convolutional Attention Network (MSCANet). Firstly, the deep group convolution is used to isolate the channel interaction in the shallow network. Then, through the multi-scale convolution module, finer-grained features of the signal are extracted without increasing the complexity of the model. Finally, the self-attention mechanism is used to suppress the influence of low-correlation and negative-correlation channels and spaces. This method overcomes the problem that the conventional method is seriously disturbed by noise. We validated the proposed method in 81 kinds of noise environments, achieving an average accuracy of 94.65%. Additionally, we discussed the performance of six machine learning algorithms and four deep learning algorithms. Compared to these methods, proposed MSCANet achieved an accuracy improvement of approximately 17%. Our method demonstrates better generalization and robustness.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

Signal-to-noise ratio (SNR) is an important index to evaluate radiation performance and image quality of optical imaging systems under low illumination background. Under the nighttime lighting condition, the illumination of remote sensing objects is low and varies greatly, usually ranging from several lux to tens of thousands of lux. Nighttime light remote sensing imaging requires high sensitivity and large dynamic range of detectors. Luojia 1-01 is the first professional nighttime light remote sensing satellite in the world. In this paper, we took the nighttime light remote sensing camera carried on the satellite as research object, proposed an in-orbit SNR test method based on time series images to overcome the problem of low spatial resolution. We first analyzed the process of luminous flux transmission between objects and satellite and established a radiative transfer model. By combining the parameters of large relative aperture optical system and high sensitivity CMOS device, we established SNR model and specially analyzed the effect of exposure time and quantization bits on SNR. Finally we used the proposed in-orbit test method to calculate SNR of lighting images acquired by satellite. And the measured result is in good agreement with the model predicted data. Under the condition of 10lx illumination, the SNR of typical objects can reach 27.02dB, which is much better than the requirement of 20dB for engineering application.

Curcumin, found in the rhizome of turmeric, has extensive therapeutic promises via its antioxidant, anti-inflammatory, and antiproliferative properties. Preclinical in vitro and in vivo data have shown curcumin to be an effective treatment for multiple cancers. These effects are drived by curcumin's ability to induce G2/M cell cycle arrest, induction of autophagy, activation of apoptotic pathways, disruption of molecular signaling, inhibition of invasion and metastasis, and by increasing the efficacy of existing chemotherapeutics. Here we focused on the hormetic behaviour of curcumin. Frequently, low doses of toxins and other stressors not only are harmless but also activate an adaptive stress whereas high dose activates acute responses like autophagy and cell death. This phenomenon is referred to as hormesis. Many molecules that cause cell death elicite an initial autophagic step that is a cytoprotective mechanism relying on elimination of dysfunctional structures intracellular, notably by mitophagy. This phenomenon is considered as a primarily protective mechanism against stressors. At higher doses, cells undergo mitochondrial outer membrane permeabilization due to calcium release from the endoplasmic reticulum and die. Herein, we address the complex crosstalk between the induced mitochondrial biogenesis, mitochondrial destabilization accompanied by mitophagy and cell death that can also be at play.

The idea of developing a robot controlled by iris movement to assist physically disabled individuals is indeed innovative and has the potential to significantly improve their quality of life. This technology can empower individuals with limited mobility and enhance their ability to interact with their environment. Disability of movement has huge impact on the life of physically disabled people. Therefore, there is need to develop a robot which can be controlled using iris movement. The main idea of this work revolves around iris recognition from an eye image, specifically identifying the centroid of the iris. The centroid's position is then utilized to issue commands to control the robot. This innovative approach leverages iris movement as a means of communication and control, offering a potential breakthrough in assisting individuals with physical disabilities. The proposed method aims to improve the precision and effectiveness of iris recognition by incorporating advanced segmentation techniques and fuzzy clustering methods. The fast gradient filters using a fuzzy inference system (FIS) is employed to separate the iris from its surroundings. Then, the bald eagle search (BES) algorithm is employed to locate and isolate the iris region. Subsequently, the Fuzzy KNN algorithm is applied for the matching process. This combined methodology aims to improve the overall performance of iris recognition systems by leveraging advanced segmentation, search, and classification techniques. The results of the proposed model are validated using True Success Rate (TSR) and compared to other existing models. The results highlight the effectiveness of the proposed method for the 400 tested images representing 40 people.

This study explores pressure, miscibility, and pore medium effects on heavy hydrocarbon recovery up to 65 MPa from four rock types: sand, tight sandstone, cavernous limestone, and oil sand. Results reveal MMP at 50 MPa, with peak recovery at 93% (56 MPa). Interestingly, recovery trends counter traditional expectations, notably decreasing in tight sandstone (42-56 MPa) and oil sand (50-65 MPa). Varied recoveries in cavernous limestone (25-56 MPa) highlight porosity and vug influence. Higher pressures hinder recovery due to SC-CO2's density and viscosity, favoring the immiscible process for efficient heavy hydrocarbon extraction.

Nowadays, wearable devices for human health monitoring are increasingly become popular and widely used. Typically, the wearable device is small size and operates with batteries. Therefore, the wearable device acquires bio-signals and transfers to smartphones or personal computers (PC) via WiFi/ Bluetooth for processing data. To reduce power consumption is one of the most important challenges of designing wearable devices. To solve this problem, the proposed signal quality valuation (SQV) method can be select the high-quality signal and reduce the transfer time to other devices. In this paper, the proposed SQV and data compression method rely on real-time PPG signals analysis to retain important information of PPG signal, improve performance and power consumption of PPG devices. Besides, we also proposed Heuristic rules for heart rate (HR) estimation with compression data. The experimental results show that the highest compression ratio (CR) is 387.8 with BIDMC Physionet database (sampling frequencies of 125 Hz) and HR error as 1.43 bpm for averaging absolute error (avAE), the standard deviation absolute error (sdAE as 0.4) and relative error mean (avRE as 0.019). The proposed real-time PPG measurement system (sampling frequency as 100/ 200/ 400 Hz) reduce power consumption and open the new structure for healthcare application systems

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

Protein degradation is a biological phenomena essential for cellular homeostasis and survivor. Selective protein degradation is performed by the ubiquitination system which selectively target proteins that need to be eliminated and lead them to proteasome degradation. In this review, we focus on the ubiquitin-conjugating enzyme E2 O (UBE2O) and highlight the role of UBE2O in many biological and physiological process. We further discuss the UBE2O implications in various human diseases, particularly in leukemias and solid cancers and suggest how UBE2O targeting could be novel strategy in the treatment of different human neoplasia.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

Human induced climate change led to the recognition of Community-Based Adaptation (CBA) as one of the remedies in building adaptive capacity and resilience of communities. It recognizes the resources and the skills as well as the agency of communities in shaping the optimal strategy. CBA interventions are vital in addressing community needs and contextual specificities, enable participatory and inclusive engagement and thereby facilitate more profound adaptation impacts. Agent-based modelling (ABM) harbors the potential to be the ideal tool to support developing of tailored adaptation strategies while considering capacities, resources, skills, priorities, needs and the cultural context of local communities. ABM allows to capture the complex relationships among various components within community decision making on CBA actions, the CBA actions themselves and the environment. There exist plenty of tools, however they provide for varying degrees of freedom in agent definition, sensitivity analysis, scalability, experiment design and output analysis to name a few. A set of required key criteria for CBA modelling is developed and all available ABM modelling and simulation tools are assessed for their suitability for CBA. NetLogo emerges as the most fitting tool for incorporating and handling the special features of CBA. It is closely followed by GAMA and Envision. The article provides insights and guidance to researchers and practitioners in selecting ABM tools aligned with the specific requirements of their CBA simulations and projects.

Background: Psoriasis is a chronic immune-mediated skin disease in which systemic inflammation plays an important role in the pathogenesis. In recent years, neutrophil-to-lymphocyte ratio (NLR), neutrophil-to-monocyte ratio (NMR), platelet-to-lymphocyte ratio (PLR), and systemic immune-inflammation index (SII) have been shown to be important indicators of inflammation. In this study, our aim is to investigate NLR, NMR, PLR, and SII levels in psoriasis patients treated with biologic agents. Method: Clinical and biochemical data of 209 patients who received systemic therapy for psoriasis were obtained by retrospectively reviewing their medical records. NLR, NMR, PLR, and SII values were calculated from the hemogram values of the patients. Results: In the third month of follow-up, the mean CRP, NLR, NMR, PLR, and SII values were significantly decreased compared to the baseline values. SII values showed strong positive correlations with NLR, NMR and PLR. Adalimumab, etanercept, and infliximab, which are TNF-α blockers, were observed to be more effective on PLR and NLR and especially NMR. Conclusion: NLR, NMR, PLR, and SII, which are data obtained from routine blood tests, can be used in the monitoring of treatment of psoriasis, especially with TNF- α blockers.

Atopic dermatitis (AD) is a chronic inflammatory condition which significantly affects quality of life in both patients and their caregivers. Calcineurin inhibitors (CNI) are a class of immunosuppressive drugs predominantly inhibiting T cell mediated immune processes. CNI form complex by binding with immunophilins and in turn inhibit calcineurin and suppress downstream inflammatory pathway. Tacrolimus and pimecrolimus are topical CNI approved for the treatment of mild to severe AD in both children and adults. Application site reactions are frequently seen. They have been issued with black box warning towards increased risk of malignancies but supportive evidence is lacking. Cyclosporine, though highly effective, is used off-label for AD management. It is used for controlling acute flares of AD due to its very rapid onset of action. Nephrotoxicity and hypertension are its serious complications. CNI have not been reported with teratogenicity and may be used conditionally during pregnancy and lactation.

Background/Objectives: It is known that balance disorders involve occupational hazards. However, the inverse relationship (between certain occupations and an increased incidence of vertigo or dizziness) has been scarcely studied. The objective of this work was to analyze the occupation of a group of patients with vertigo, compared to economically active general population, and to evaluate the prevalence of occupational noise and/or vibration-exposure in both groups. Methods: A cross-sectional, observational, case-control study was carried out including 461 patients (220: Meniere’s disease; 73: vestibular migraine; 28: vestibular neuritis; 140: BPPV) (310 women and 151 men). These patients were compared to a control group from the general population, obtained from 6th EWCS-Spain (2015). Possible differences regarding sex, age, occupation, exposure to noise, and exposure to mechanical vibrations were analyzed. Results: Differences in distribution of occupations between patients with vertigo and general population were observed (Chi-square, p=6.142 e-30). Patients with vertigo were significantly more exposed to noise (p=8.19 e-12; OR=2,127, CI95% (1.720;2.630)) and vibrations (p=1.11 e-12; OR=2.288, CI95% (1.835;2.853)) than the control group. These differences were observed both between men and women. Conclusions: A relationship between occupational exposure to noise and/or vibrations and the presence of vertigo was observed. Protective and preventive measures could help prevent the occurrence of some diseases involving vertigo.

In this work, we explore the ability to dynamically group the Wind Turbine (WT) of a Wind Farm (WF) based on the behaviour of some of their Supervisory Control And Data Acquisition (SCADA) signals to detect the turbines that exhibit abnormal behaviour. We centre this study on a small WF of five WTs. We use the fact that the same signals from different turbines in the same WF coherently evolve temporally in a time domain, describing very similar waveforms. In this contribution, we use averaged signals from the SCADA system and omit maximums, minimums and standard deviations, focusing mainly on velocities and other slowly varying signals. For the temporal analysis, sliding windows of different temporal durations and overlapings are explored. The capability to automatically identify WTs whose signals differ from the group’s behaviour can alert and program preventive maintenance operations on such WTs before a major breakdown occurs.

This paper investigates the efficacy of YOLOv8 variants for vehicle detection and license plate detection within smart parking applications, emphasizing performance under varying ambient lighting conditions. The proposed system is to seize full video frames, extracts regions of interest containing vehicles, and feeds them into separate, pre-trained YOLOv8 models – one dedicated to vehicle detection and another for license plate detection. Four YOLOv8 variants, nano, small, medium, and large, are evaluated. As a pre-processing step, the images are processed with the help of OpenCV and Pillow libraries to adjust the luminosity and increase the images’ DPI so that they would be easy to perceive by the Tesseract OCR engine. Sixteen potential combinations arise from pairing the four YOLOv8 models for vehicle and license plate detection tasks. To identify the most suitable combinations, we employ the Multi-Criteria Decision-Making method, specifically Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) analysis. This analysis considers 4 critical metrics: Precision, mean average precision at 95% Intersection of Union threshold, Recall and Total Inference Time. The objective is to achieve an optimal balance between high accuracy and real-time processing. Following the selection of optimal YOLOv8 combinations through TOPSIS analysis, we assess their performance under varying ambient light intensity (measured in lux). This evaluation aims to identify the most robust model combinations that ensure accurate vehicle and license plate recognition across the diverse lighting conditions encountered in real-world environment.

This article touched upon various issues regarding vulnerability, disparities amongst community settings, and the effect of air pollution on the populace (low-income communities). Furthermore, the paper emphasized environmental ethics approaches like anthropocentric, nature-centric, and deep-ecological approaches. More so, it addresses the importance of handling these disparities, particularly from the geopolitical dimension, and recommends cross-border cooperation and accountability in promoting environmental justice in India.

Biopolymer gels have gained tremendous potential for therapeutic applications due to their biocompatibility, biodegradability, and ability to adsorb and bind biological fluids, making them attractive for drug delivery and therapy. The versatility of biopolymer gels in theranostic backgrounds, with a focus on integrating imaging features and facilitating real-time monitoring of drug delivery. Different methods of delivery are explored imaging agents into biopolymer gels, including encapsulation, surface functionalization, nanoparticle encapsulation and layer-by-layer assembly techniques. Integration of Agents and Real-Time Monitoring Drug Delivery We summarize the synthesis methods, general properties, and mechanisms of biopolymer gels functionality, demonstrating their broad applications as multimodal systems for imaging-based therapeutics. These techniques not only enable multiple imaging but also provide signal enhancement and imaging a targeted facilitates, increasing the diagnostic accuracy and therapeutic efficacy. In addition, current techniques for incorporating imaging agents into biopolymer gels are discussed, and their role in precise drug delivery and monitoring.

The abilities of quantitative description of noise are restricted due to its origin and only the statistical and spectral analysis methods can be applied while an exact time evolution cannot be defined or predicted. It emphasizes the challenges faced in many applications including communication systems where noise can play, on one hand, a vital role impacting signal-to-noise ratio but possessing, on the other hand, unique properties such as infinite entropy (infinite information capacity), exponentially decaying correlation function and so on. Despite the deterministic nature of chaotic systems, the predictability of chaotic signals is limited for a short time window putting them close to random noise. In this article, we propose and experimentally verify an approach to achieve Gaussian-distributed chaotic signals by processing the outputs of chaotic systems. The mathematical criteria, on which the main idea of the study is based on, is the Central Limit Theorem which states that the sum of a large number of independent random variables with similar variances approaches a Gaussian distribution. The study involves more than 40 mostly three-dimensional continuous-time chaotic systems (Chua’s, Lorenz’s, Sprott’s, memristor-based, etc.) whose output signals are analyzed according to criteria that encompass the probability density functions of a chaotic signal itself and its envelope and phase, statistical and entropy-based metrics such as skewness, kurtosis, and entropy power. We found that two chaotic signals of Chua’s and Lorenz’s systems exhibited superior performance across the chosen metrics. Furthermore, our focus extended to determining the minimum number of independent chaotic signals necessary to yield a Gaussian-distributed combined signal. The analytic and experimental results indicate that the sum of at least three non-Gaussian chaotic signals closely approximates Gaussian distribution. It allows generation of reproducible Gaussian-distributed deterministic chaos by modeling simple chaotic systems.

Ultrasonic imaging & NDE applications can greatly improve their signal-to-noise ratios (SNR) by driving each transducer (composing piezoelectric arrays) with a spike giving pulsed power of k-Watts, repetitively at a PRF = 5000 spikes/s, by using a HV capacitive-discharge generator. However very-high levels, of pulsed intensities (3-10 A) and voltages (300-700 V) must be considered for a rigorous spike modeling. Even though the consumed "average" power will be small, the intensity through each transducer achieves several amperes, so the pulsed powers delivered by each HV generator can attain levels higher than in CW high-power ultrasonic applications: e.g., up to 5 kW / spike. This is concluded here from a transient modeling of the loaded generator. Then, unforeseen phenomena rise: intense brief pulses of driving power & emitted force in transducers, and non-linearities in driver semiconductors, because their characteristic curves only include linear ranges. But fortunately, piezoelectric devices working in this intense regime do not show serious heating problems, because the average power remains being moderate. Intensity, power and voltage, driving a broadband transducer from a HV capacitive pulser, are calculated to drastically improve (in ≅ 40 dB) the ultrasonic net dynamic range available, with emitted forces ≅ 250 Newtons pp and E/R received pulses of 70 V pp.

The development of mineral resources in China has gradually entered the stage of deep mining. Rock burst, collapse and other ground pressure disasters caused by deep high stress have become major hidden dangers restricting mine safety production. Microseismic monitoring technology is an important means of ground pressure risk prediction. In this paper, the wavelet coefficient threshold denoising method in time-frequency domain, STA/LTA method, AIC method, Skew and Kurtosis method are studied, and the automatic P-phase onset time picking model based on noise reduction and multiple detection indexes is established. Through the effect analysis of microseismic signals collected by microseismic monitoring system of coral Tungsten Mine in Guangxi, automatic P-phase onset time picking is realized. the reliability of the P-phase onset time picking method proposed in this paper based on noise reduction and multiple detection indexes is verified. The picking accuracy can still be guaranteed under the severe signal interference of background noise, power frequency interference and manual activity underground mine, Which is of great significance to the data processing and analysis of microseismic monitoring.

The architectural configuration of the space plays a crucial role in the acoustics of Neonatal Intensive Care Units (NICUs). The design of the environment, the materials used in construction, and the organisation of noise sources within the room significantly influence the noise levels present in these critical areas. For this research, noise levels found in two hospitals, with different architectural configurations and sizes but similar construction materials, have been analyzed. Data were recorded at 1-second intervals over a period of more than 24 hours. The data collected in these hospitals confirm the magnitude of the noise problem in NICUs, highlighting the urgent need to address it effectively to ensure an appropriate and safe environment for the recovery of neonates. Good architectural planning can help mitigate noise, while poor configuration can exacerbate acoustic problems, negatively affecting both patients and healthcare staff. It is crucial to involve architects, acoustic engineers, and healthcare staff in the design and renovation of NICUs to create spaces that not only meet medical needs but also consider the auditory well-being of neonates.

Bacillus amyloliquefaciens GL18 has been proven to have good resistance ability and can promote the growth of Avena sativa cultivar ‘Qingyan 1’. Herein, Illumina high-throughput transcriptome sequencing technology was used to analyze the differential expression of genes between the interaction group (LB) and the control group (LCK) when ‘Qingyan 1’ roots interacted with GL18 bacterial suspension or sterile water for 12 h under 4 °C low-temperature stress. The gene function annotation information was obtained using Gene Ontology (GO) functional classification and enrichment analysis. Kyoto Encyclopedia of Genes and Genomes (KEGG) pathway enrichment analysis and annotation of differentially expressed genes was used to explore the related signal transduction pathway of ‘Qingyan 1’ response to cold stress induced by Bacillus GL18. The results showed that after ‘Qingyan 1’ seedlings interacted with GL18 bacterial suspension or sterile water for 12 h, comparing the LB with the LCK or CK (the control group at 26 °C), there were 12,061 and 25,489 differentially expressed genes, respectively. Their functions were mainly related to metabolic process, cellular process, catalytic activity, binding, and cellular parts, and they were significantly enriched in plant tissue growth and development, cell wall, organelle membrane synthesis, thiamine and its compounds, biosynthesis, polyamine decomposition, and other metabolic processes. Signal transduction was detected through KEGG pathway enrichment analysis, and corresponding genes, such as AUXI, PP2C, SNRK2, ABF, BRI1, and PIF4, were expressed. The expression of genes directly involved in plant growth was upregulated in the presence of GL18, as shown by real-time quantitative PCR analysis. It was speculated that the normal growth and development of ‘Qingyan 1’ under low-temperature stress promoted by GL18 is a result of the integration of multiple pathways in terms of regulating endogenous hormone metabolism, secondary metabolite synthesis, and photosynthesis.

The extent of access to energy of displaced populations in settlements and camps in Africa is largely 14 unknown. A multitude of contextual factors, such as the location and the characteristics of housing, 15 the legal status, the socio-cultural background, and the availability of humanitarian and public ser- 16 vices impact the living conditions and the needed energy services. Limitations in accessing energy 17 services have direct, multilayered, and far-reaching implications, including impacts on health, nu- 18 trition, education, protection, and livelihood. The objective of this article is to contribute to a more 19 comprehensive overview of the current state of energy access in displacement contexts on the Afri- 20 can continent by identifying and utilizing existing data. After a screening of the vast and various 21 available information, setting up of a database, consolidating the gathered data as well as assessing 22 the quality through a quality assessment method, the currently available information is visualized 23 and discussed. Considerable differences in the access to electricity for displaced persons across the 24 countries are found. For both electricity and clean cooking, the availability for displaced persons 25 ranges from nearly no access at all up to an access rate of 100%. More strikingly, the results also 26 show that besides South Africa and countries in the Maghreb region, the access to both clean cook- 27 ing and electricity for displaced persons is very low. At the same time, the fragmented data availa- 28 bility, the poor data quality, and the questionable expediency of available data allows neither solid 29 theoretical conclusions nor planning of effective practical implementation measures. Novel inter- 30 disciplinary research, conceptual frameworks and indicators are needed for the purpose of compa- 31 rability and consistency. Future research has the potential to more comprehensively capture the 32 current state of access to energy in displacements contexts and in a next step to examine how energy 33 is interwoven in the lives of displaced people to derive a set of more detailed context-sensitive en- 34 ergy indicators. It is essential that the concerned persons, the displaced persons themselves are in- 35 cluded in the research in a meaningful way.

Uncertainties in initial water saturation and early water breakthroughs of un-known sources and paths, which occurred in the low resistivity Lower Haushi sand-stone (LHS) reservoir at the beginning of oil production, imply that the bypassed oil can yet remain in the reservoir. In addition, the upper part of LHS is a tight oil reser-voir, which can still contain a significant amount of unrecovered oil. This opens the opportunity to produce the remaining oil instead of abandoning this reservoir. Low resistivity can exaggerate water saturation, leading to misinterpretation and premature water flooding due to inadequate oil-water contrast. Our analysis revealed a correlation between low resistivity and robust porous network connectivity, along-side elevated formation water salinity in highly porous layers. In regions of high po-rosity, sufficient oil-water contrast facilitates precise water saturation determination, affirming oil presence in all wells. However, within tight oil zones, near-complete wa-ter saturation contradicts actual oil presence. Factors contributing to saturation un-certainty and water breakthroughs were reassessed. Utilizing a 1:1 verti-cal-to-horizontal permeability ratio derived from core data enhanced simulation alignment with water production rates. Investigation into the impact of relative per-meabilities on water production was conducted. Water saturation maps were gener-ated to pinpoint remaining oil reserves. Depletion around wells is evident in lower po-rous regions, while oil persists across the entire tight reservoir, notably in two unex-plored sections.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

Time evolution of the quantum correlation of the hybrid qubit-qutrit system in multilocal and global dephasing under the effect of a classical noises environment is presented. We considered the qutrit in z direction and the qubit x direction. In addition, our system presents two configurations: the different and the common environment and our discussion involves three types of noises: A Static Noise (SN), Random Telegraph Noise (RTN) and Ornstein- Uhlenbeck noise (OU). By using the density matrix approach to determine the evolution of the state of the system, the found that the static noise is fatal for the quantum entanglement, the quantum correlation and for RTN and OU noises the quantum entanglement, the quantum correlation decreases monotonically with a sufficiently long time. Therefore, we can say that, entanglement and the quantum correlation are more robust to the noise precisely those Random telegraph noise and Ornstein-Uhlenbeck noise.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

The realization of a perfect absorber A = 1 with transmittance and reflectance T=R=0 by a thin metasurface is one of the hot topics in recent nanophotonics prompted by energy harvesting and sensor applications (A + R + T =1 is the energy conservation). Here we tested optical properties of over 400 structures of metal-insulator-metal (MIM) metasurfaces for a range of variation in thickness of insulator, the diameter of a disc and intra-disc distance experimentally and numerically. Conditions of a near-perfect absorption A > 95% with simultaneously occurring anti-reflection property (R < 5%) were experimentally determined. Differences between the bulk vs. nano-thin film properties at mid-IR of the used materials can be of interest for plasmonic multi-metal alloys and high entropy metals.

According to current forecasts, global heating is likely to exceed 2,8°C by the end of the century. This makes substantial adaptation measures necessary to secure a broad basis for livelihoods provision and the conservation of biodiversity. While the implementation of top-down and technocratic adaptation efforts is the majority, related adaptation shortcomings of socio-economic and ecological nature are becoming more and more apparent. Community-based adaptation (CBA) with its participatory, inclusive and needs-based bottom-up approach offers a promising and powerful alternative. This article uses a semi-systematic literature review approach to screen the current literature and identify core issues of CBA. Linking communality, locality, multidimensionality, power imbalances, transformative potential, localisation, the triad of adaptation metrics and adaptation with nature to corresponding potential actions for practical implementations provides a more holistic conceptualisation and broadens the horizons for further learnings, research and improved application.

In recent years, bioengineered and biotechnological products have gained tremendous attention to identify unique biologic features associated with oncology. To overwhelm the complexity of tumor personalized medicines (PM) or vaccines could be a promising way-out to be considered. Cancer is a heterogeneous disease. This characteristic variability of cancer provides itself to the emergent era of PM i.e., precision oncology. The prime objective of PM is merely to deliver the right treatment to the right patient at the right time. For instance, imatinib was effectively targeted chronic myeloid leukemia. To date, attainment in using PM approaches to cancer treatment have been mixed. The next-generation sequencing (NGS), and the use of several biomarkers (e.g., HER2, BRAF, ALK, etc.), to drive precise cancer treatment through a timely and cost-effective manner. In current review, author summarizes the advancement in the field of PM such as CRISPR-Cas9, NGS, pharmacogenomics, and the benefits of machine learning techniques. The precise communication between healthcare professionals, regulatory bodies, and patients is essential to translate advances in PM into immense benefits for patients with cancer globally.

The search of DNA polymorphisms useful for the genetic improvement of dairy farm animals lasts more than 40 years with relevant findings in cattle for milk traits, where the best combination of alleles for dairy processing have been found in casein genes and in the DGAT1. Nowadays, similar results are not reached yet in river buffaloes despite advanced genomic technologies and accurate phenotype records are available. The aim of the present study was to investigate and validate in a larger buffalo population the effect on six milk traits of four single nucleotide polymorphisms (SNP) in the CSN1S1, CSN3, SCD and LPL genes, previously reported to be associated with or affect dairy traits in smaller populations often belonging to one farm. A total of 800 buffaloes were genotyped. Daily milk yield (dMY, kg), protein yield (dPY, kg) and fat yields (dFY, kg), fat and protein contents (dFP, % and dPP, %), somatic cell count (SCC, 103cell/ml) and urea (mg/dl) were individually recorded in each month for the whole lactation from 2010 to 2021. A total of 15,742 individual milk test day records (2,496 lactations) were available on 680 buffalo cows with 3.6±1.7 parity (from 1 to 13) and 6.1±1.2 test day records per lactation on average. Three out four SNP in CSN1S1, CSN3 and LPL were associated with at least one of analyzed traits. In particular, the CSN1S1 (AJ005430:c.578C&gt;T) gave favorable associations with all yield traits (dMY, p=0.022; dPY, p=0.014 ; dFY, p=0.029) and SCS (p=0.032), whereas the CSN3 (HQ677596: c.536C&gt;T) positively associated with SCS (p=0.005) and milk urea (p=0.04). Favorable effect on dMY (p=0.028), dFP (p=0.027) and dPP (p=0.050) were observed for the LPL. Conversely, SCD did not show any association with milk traits. This is the first example of confirmation study carried out in the Mediterranean river buffalo for genes of economic interest in dairy field and it represents a very important indication for the preselection of young bulls destined to breeding programs in the view of a more sustainable dairy production.

In the frame of the I-MOVE-COVID-19 project, a cohort of 2050 patients admitted in two Spanish reference hospitals between March 2020 and December 2021 was selected, and a range of clinical factors data were collected at admission to assess their impact on the risk COVID-19 severity outcomes through a multivariate adjusted analysis and nomograms. The need for ventilation and ICU admission were found directly associated with a higher mortality risk (OR 6.9 and 3.2, respectively). The clinical predictors of mortality were need for ventilation and ICU, advanced age, neuromuscular disorders, thrombocytopenia, hypoalbuminaemia, dementia, cancer, elevated CPK and neutrophilia (OR between 1.8 and 3.5), whilst the presence of vomiting, sore throat and cough diminished risk of death (OR 0.5, 0.2 and 0.1 respectively). Admission to ICU was predicted by the need for ventilation, abdominal pain and elevated LDH (OR 371.0, 3.6 and 2.2, respectively) as risk factors; otherwise, it was prevented by advanced age (OR 0.5). In turn, the need for ventilation was predicted by low oxygen saturation, elevated LDH and CPK, diabetes, neutrophilia, obesity and elevated GGT (OR between 1.7 and 5.2), whilst prevented by hypertension (OR 0.5). These findings could enhance patient management and strategic interventions to combat COVID-19.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

Senna rugosa is a species found in the Cerrado and used in folk medicine as a vermifuge and in the treatment of poisonous snakebites accidents. In this work, we identified the main secondary metabolites present in ethanolic extracts of the leaves (ELSR) and roots (ERSR) of S. rugosa and evaluated the potential cytoprotective effect against cellular macromolecular damage, as well as the cytotoxic properties of the extracts on the K562 and Jurkat leukemic cell lines. The identification of metabolites was done by liquid chromatography coupled with mass spectrometry. The antioxidant activities were investigated by direct ABTS•+ and DPPH• radical scavenging methods, protection against oxidative damage in proteins and DNA. The cytotoxic properties were investigated against healthy cells, isolated from human peripheral blood (PBMC) and leukemic cell lines. The leaf extract contains catechin, rutin, epigallocatechin derivatives, kaempferol glycosides, luteolin, and dimeric and trimeric procyanidins, while the root extract profile shows obtusichromoneside derivatives, 2-methoxystypandrone, stilbene derivatives, naphthopyranones, and flavanone derivatives. The extracts showed antioxidant activity, with IC50 of 4.86 ± 0.51 µg/mL and 8.33 ± 0.90 µg/mL in the ABTS assay for ELSR and ERSR, respectively. And in the DPPH• assay, the IC50 was 19.98 ± 1.96 µg/mL for ELSR and 13.37 ± 1.05 µg/mL for ERSR. The extracts protected macromolecules against oxidative damage at concentrations of 5 µg/mL. The cytotoxicity test against leukemic strains was observed after 24 and 48 hours of treatment. After 48 h, results against the K562 cell line demonstrate IC50 of 242.54 ± 2.38 µg/mL and 223.00 ± 2.34 µg/mL for ELSR and ERSR , respectively. While against the Jurkat cell line, these extracts showed IC50 of 171.45 ± 2.25 µg/mL and 189.30 ± 2.27 µg/mL, respectively Results on PBMC viability, demonstrate that the extracts showed selectivity for the leukemic cell lines. Together, our results reveal that the leaves and roots of S. rugosa have completely distinct and complex chemical compositions. This study expands the repertoire of identified chemical compounds and underscores their significant pharmacological potential in conditions related to oxidative stress and leukemia.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

Antibacterial bone cements (ABCs), such as antibiotic-loaded bone cements (ALBCs), have been widely utilized in clinical treatments. Currently, bone cements loaded with vancomycin, gentamicin, tobramycin, or clindamycin are approved by the US Food and Drug Administration. However, traditional ALBCs exhibit drawbacks like burst release and bacterial resistance. Therefore, there is a demand for the development of antibacterial bone cements containing novel agents. In this review, we summarize the latest advancements in ABCs. More importantly, we provide an overview and outlook on novel antibacterial agent-loaded bone cements, including metallic antibacterial agents, pH-switchable antibacterial agents, cationic polymers, N-halamines, non-leaching acrylic monomers, antimicrobial peptides, etc. Offering novel perspectives for designing ABCs and treating bone infections.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

In the area of dental healthcare services, where patients and professionals deal with multiple auditory stimuli, this cross-sectional study reports on the intricate dynamics of sound preferences, noise obstacles, and the profound impact of music on anxiety reduction within dental office set-tings. The sample comprises of 134 dental patients, primarily females (56.7%), with varying age groups, education levels, and therapy durations in the university clinics of the department of Dentistry, National and Kapodistrian University of Athens and four private dental offices at the metropolitan area of Athens, Greece. Notably, 92.5% of the participants report no hearing loss, and 56.7% exhibit some level of noise sensitivity. The study reveals a moderate to good perceived health status (M=3.84, SD=0.95) among participants, with low perceived noise disturbance in university dental clinics. Preferences for instrumental music, foreign pop, and classical music are prominent during waiting times. Potential irritations include impersonal treatment (44%) and staff behavior (41.8%). Music player usage within the settings of the dental clinic involves radios (49.3%) and headphones (41.0%). Correlations and predictors indicate associations between health status, music preferences, and noise disturbances. More specifically, visiting the university dental clinics (β = .300, p = .005) as well as younger age (β = .300, p = .034) were significant predictors of better perceived health status. Clearer perception of external sounds while using the music player (β = .190, p = .039) was a significant predictor of better perceived health status, while poorer health was predicted by the preference of Greek folk songs (β = -.200, p = .030). Also, the use of smartphones for playing music was related to poorer health (β = -.370, p < .001). Following, younger age (β = -.270, p = .015), lower education (β = -.210, p = .035), higher noise sensitivity (β = .190, p = .027), as well as feelings of anxiety and nervousness due to ambient noise from people and machines (β = .510, p = .027) were significant predictors of noise disturbance from machines. Also, visiting private clinics (β = .240, p = .018), preferences of specific playlist (β = .310, p = .012), no music (β = .280, p = .016) and use of smartphones to play music (β = .230, p = .029) were significant predictors of noise disturbance from patients or staff. Finally, the preference of listening to a specific playlist was related to better health status (r = .190, p < .05). Findings aim to optimize eco-soundscapes in dental offices, con-tributing to enhanced patient well-being. The research underscores the potential of music inter-ventions to alleviate dental anxiety and improve the overall dental experience and quality care.

Background and objective: Analysis of inflammatory biomarkers, along with the neutrophil/lymphocyte ratio (NLR) or platelets/lymphocyte ratio (PLR), supports the connection between inflammation and carcinogenesis. Methods: We conducted a retrospective observational study at the Clinical County Hospital Mureș, including patients with lung cancer. The parameters analyzed included: histopathological type (NSCLC - squamous cell carcinoma or adenocarcinoma; SCLC), molecular mutations (EGFR, ALK, PD-L1), parameters from the complete blood count, inflammatory parameters and associated comorbidities. Results: 380 patients were included: 115 patients in the cancer group and 265 patients in the control group. Among patients in the lung cancer group, 88 were diagnosed with NSCLC (44 adenocarcinomas, 44 squamous cell carcinomas) and 27 with SCLC. Both NLR and PLR were significantly higher in cancer patients than in the control group (5,30 versus 2,60, p&lt;0,001; 217 versus 136, p&lt; 0.001, respectively). NLR and PLR differs between men and women (p = 0.005, respectively p=0.056). C-reactive protein was not correlated with either NLR (p-value: 0.0669) or PLR (p-value: 0.6733) in lung cancer patients. Conclusion: The NLR and PLR values ​​may serve as new predictive biomarkers for the diagnostic of disease in patients with lung cancer, especially those with NSCLC.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

Emphasizing the importance of acoustic attenuation in maintaining compliance with stringent noise regulations and enhancing workplace safety, the analysis covers the theoretical and practical aspects of sound attenuation in a turboengine testing stand. This paper presents a preliminary analysis and also an evaluation of a procedure for projecting a noise attenuator for industrial application and especially for turboengine test stands. While primarily focusing on the static acoustic behavior of the attenuator, considerations were also made regarding flow dynamics, Mach number-dependent attenuation, pressure drop, and self-generated noise aspects to provide a comprehensive perspective in selecting the optimal design configuration. The study investigates different calculation methods for assessment of the noise reduction for linear and staggered baffles, applied on a scaled reduced model of attenuator. Thus, the critical parameters and projecting requirements necessary for effective noise reduction in high-performance turboengine testing environments will be evaluated in a down-scaled model. Key factors examined include the selection of design parameters and configurations from various options. Advanced computational methods, like analytic and finite element analysis (FEM) are utilized to predict the acoustic performance and identify potential design optimizations. Experimental validation is performed to corroborate the simulation results, ensuring the reliability and efficiency of the attenuator. The findings indicate that a well-designed sound attenuator module can significantly reduce noise levels without compromising the operational performance of the turboengine inside a test cell.

The pervasive use of plastic for milk packaging has raised significant health concerns, despite its advantages in terms of cost-effectiveness, convenience, and durability. The potential correlation between cancer and plastic packaging is one of these concerns. This mini-review examines the health implications of plastic materials used in milk packaging, with a particular emphasis on their carcinogenic hazards. This work endeavors to summarize the current state of knowledge regarding the influence of plastic components on human health and underscore the importance of ongoing research in this field by utilizing insights from a comprehensive review article. Harmful chemicals have been observed to leach into milk from plastics used in milk packaging, including high-density polyethylene (HDPE), low-density polyethylene (LDPE), and polyethylene terephthalate (PET), particularly under conditions of protracted storage and heat. Bisphenol A (BPA), phthalates, and styrene are among the most prevalent leachates. These chemicals have been associated with a variety of health issues, such as an elevated risk of cancer, and are recognized for their endocrine-disrupting properties. BPA and phthalates, in particular, have the potential to disrupt hormone function, which may result in breast cancer, prostate cancer, and other hormone-related malignancies.This review emphasizes the significance of comprehending the precise components of plastics utilized in milk packaging and their potential health consequences. It advocates for more rigorous research to completely elucidate the long-term health impacts of these materials by emphasizing the current state of knowledge and regulatory initiatives. Additionally, it underscores the necessity of innovative packaging technologies to guarantee consumer protection and mitigate the risk of exposure to carcinogenic substances.

The application of signal-to-noise ratio (SNR) observations from ground-based GNSS Reflectometry is becoming an operational tool for coastal sea-level altimetry. As in all data analyses, systematic influences must be reduced here too, to achieve reliable results. A prominent influence results from atmospheric refraction. Different approaches exist to describe or to correct for this influence. In our contribution we will revise the latest developments and suggest a simple atmospheric interferometric delay model that takes into account ray bending as well as along-path propagation delay. The model takes into account a spherical reflector and can therefore be applied for data from very low elevation angles, too. The findings are double-checked by numerical experiments based on a step-by-step raytracing procedure.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

This study measures the noise levels in a baseball stadium and analyzes baseball fans’ attitude of effect of recreational noise exposure on their hearing. In the baseball stadium, noise levels were measured in four seating sections using a sound level meter during the games. The LAeq average of the 16 measures produced 91.7 dBA, showing a significantly high noise level in the red and navy sections. As a function of frequency by LZeq analysis, the noise levels were significantly higher in low frequencies than other frequencies. For the survey sample, 688 randomly selected participants completed a 16-question survey on their noise exposure during the game and on the potential risk of hearing loss. Despite the very high noise levels, 70% of the respondents preferred sitting in either the red or the navy section to be closer to the cheerleaders and to obtain a good view. Most respondents reported that they did not consider wearing earplugs, and one-third experienced hearing muffled speech after the game. We conclude that the noise levels in baseball stadiums are high enough to cause hearing damage and/or tinnitus later, but expect these results to improve public education regarding safe noise exposure during popular sports activities.

: Inflammation may mediate the association of mitral valve prolapse (MVP) with ventricular scarring and arrhythmia. The purpose of this study is to investigate the association of neutrophil- and platelet-to-lymphocyte ratios (NLR, PLR) with ventricular arrhythmia in MVP. Clinical and demographic data were extracted from electronic medical records for all patients aged 18-90 years with MVP on echocardiography between 2016-19 at our institution. We studied 65 patients who had a differential blood count within six months prior to ambulatory ECG (A- ECG) (medi-an age [IQR] 70 [61-77] years; 62% female; 12% African American). Patients with surgery or in-fection within six months prior to CBC were excluded. Complex or frequent ventricular ectopy (cfVE) was defined as the presence of two or more premature ventricular contractions (PVCs) on a 10-second ECG tracing or greater than 1% PVC burden or NSVT on ambulatory ECG monitoring. Logistic and bivariate regression was used to analyze clinical, electrocardiographic and echo-cardiographic factors associated with NLR and PLR. Factors associated with higher NLR were congestive heart failure (p=0.005), male sex (p=0.01), age (p=0.003), and bileaflet MVP (p=0.04). NLR was associated with higher absolute PVC burden (rs=0.28, p=0.03) and cfVE (median NLR [IQR] 3.0 [1.6 – 6.3]) with cfVE versus (2.4 [1.4-3.4], p=0.04) without cfVE. An NLR of 5.6 yielded 50% sensitivity and 90% specificity for PVC burden >1% (AUC 0.69). No significant association was found between PLR and PVC burden or cfVE. NLR is associated with PVC burden and com-plex ventricular ectopy in MVP, suggesting that inflammation is a significant factor in the patho-genesis of ventricular arrhythmia in this condition.

For a hierarchy of large scale structures, like galaxies, galaxy clusters, super-clusters, etc. the requirement that their gravitational (binding) self-energy density must at least equal or exceed the background repulsive dark energy density implies a universal mass-radius relation given by M/R² ~ 1g/cm². Here we point out that this mass-radius relation also holds for important individual biological structures, and even various organisms as a whole such as humans, trees, and to behemoths like whales, even though the physics is different. Here we try to understand this universality from two different physical considerations. We also point out the coincidence that the densities of most biological entities are close to that of water, and that the average density of main-sequence stars and giant planets are close to this density. We give a physical basis for the same.

The production of recombinant proteins in Escherichia coli is often challenged by cytoplasmic expression due to proteolytic degradation and inclusion body formation. Extracellular expression can overcome these problems by simplifying downstream processing and improving protein yields. This study aims to compare the efficiency of two Bacillus subtilis chitosanase signal peptides in mediating extracellular secretion in E. coli. We identified a naturally occurring mutant signal peptide (mCsn2-SP) from B. subtilis CH2 chitosanase (CH2CSN), which is characterized by a deletion of six amino acids in the N-region relative to the signal peptide (Csn1-SP) from B. subtilis CH1 chitosanase (CH1CSN). The CH1CSN and CH2CSN genes were cloned into the pET-11a vector and protein secretion was evaluated in E. coli BL21(DE3) host cells. Expression was induced with 0.1 mM and 1 mM IPTG at 30°C for one and three days. CH2CSN showed higher secretion levels compared to CH1CSN under all experimental conditions, especially with 0.1 mM IPTG induction for 3 days, which resulted in a 2.37-fold increase in secretion. These results suggest that signal peptide deletion variants may have an effect on protein secretion efficiency and help to further understand the function of signal peptides.

The limits for recording weak signals for electrochemical seismic sensors are determined by their self-noise. At the same time, the noise nature is complex and not fully understood. In this work, for the first time, in addition to the frequency dependences of the noise amplitude, the difference in the phases of the noise currents of the cathodes of an electrochemical sensor has been studied. It has been established that at low frequencies the cathode currents change in an-tiphase. As the frequency increases, the phase difference becomes random. At the same time, the frequency at which the phase difference changes depend on the interelectrode distance; the clos-er the electrodes are located to each other, the greater it is. Physically, this effect is explained by the transition from noise caused by the integral flow of the working fluid to noise associated with vortex flows, the size of which depends on frequency. Thus, a new way of studying noise makes it possible to identify its physical nature and develop new methods of reduction.

Aiming to improve medical diagnosis and treatment, artificial intelligence (AI) has emerged as a transformational force in the healthcare industry. In this article, we examine how AI is increasingly being used to improve healthcare, with an emphasis on how it is changing medical diagnosis and treatment. We explore the opportunities, threats, and ethical concerns of incorporating AI into healthcare practice. In addition, we feature important AI applications in radiology, pathology, cardiology, and cancer. AI has great potential to improve patient outcomes, diagnostic accuracy, and the ability to provide individualized treatment plans in the future if it is used and refined with care.

Several recent studies have indicated that miR-30a plays critical roles in various biological processes and diseases. However, the mechanism of miR-30a participation in the regulation of idiopathic pulmonary fibrosis (IPF) is ambiguous. Our previous study demonstrated that miR-30a may function as a novel therapeutic target for lung fibrosis by blocking mitochondrial fission, which is dependent on dynamin-related protein-1 (Drp-1). However, the regulatory mechanism between miR-30a and Drp-1 has yet to be investigated. In addition, whether miR-30a can act as a potential therapeutic has not been verified in vivo. In this study, the miR-30a expression in IPF patients was evaluated. Computational analysis and a dual luciferase reporter system assay were used to identify the target gene of miR-30a, and cell transfection was used to confirm this relationship. Ten-eleven translocation 1 (TET1) was validated as a direct target of miR-30a, and the transfection of miR-30a mimic/inhibitor significantly reduced/increased the expression of TET1 protein. Further experiment verified that the interference on TET1(siRNA) could inhibit the hydroxymethlation of the Drp-1 promoter. Finally, miR-30a agomir was designed and applied to identify and validate the therapeutic effect of miR-30a in vivo. Our study demonstrated that miR-30a could inhibit the TET1 expression by base pairing with complementary sites in the 3′ untranslated region to regulate the hydroxymethlation of the Drp-1 promoter. Furthermore, miR-30a could act as a potential therapeutic target for IPF.

The occurrence of chaotic instability of oscillations at the output of a single-stage amplifier on a powerful bipolar microwave transistor when a biharmonic signal is amplified is considered. It has been established that at a high level of the input signal at the output of the amplifier, the signal contains a significant chaotic component. Cases were experimentally studied when the frequency distance between the partial frequency components of a biharmonic signal is close to the gain band and when it is much smaller than this band. It has been established that in the first case, the chaos in oscillations is associated with the emergence of a sequence of trains of a forced oscillatory process with arbitrary initial phases and durations. In the second case, the appearance of a chaotic pedestal is associated with the chaos in the passive underexcited mode of the nonlinear circuit formed by the capacitance of the p-n junction and the input matching circuits of the amplifier stage.

The coexistence of SAH with T2DM is a common comorbidity. In this present study, we investigated the link between altered plasma antioxidant trace elements (ATE: Manganese, Selenium, Zinc and Copper) and fatty acids ratio (FAR: polyunsaturated/saturated) imbalance as transition biomarkers between vascular pathology (SAH) to metabolic pathology (T2DM). Our data revealed strong correlation between plasma ATE and FAR profile which is modified during SAH-T2DM association compared to healthy group. This relationship is mediated by lipotoxicity (simultaneously prominent visceral adipose tissue lipolysis, significant flow of non-esterified free fatty acids release, TG-Chol-dyslipidemia, high association of Total SFA, Palmitic acid, Arachidonic acid and PUFA 6/ PUFA 3; drop in tandem of PUFA / SFA and EPA+DHA); oxidative stress (lipid peroxidation confirmed by TAS depletion and MDA raise, concurrently drop of Zn/Cu-SOD, GPx, GSH, Se, Zn, Se/Mn, Zn/Cu; concomitantly enhance Cu, Mn and Fe); endothelial dysfunction (endotheline-1 increase); athero-thrombogenesis risk (concomitantly raise of ApoB100/ApoA1, Ox-LDL, tHcy and Lp(a)) and inflammation (higher of Hs-CRP, Fibrinogen and Ferritin). Our study open to new therapeutic targets and to better dietary management, such as to establish dietary ATE and PUFA 6 / PUFA 3 or PUFA / SFA reference values for atherosclerotic risk prevention in hypertensive-diabetics patients.

Plant activators have emerged as promising alternatives to conventional pesticides for crop disease manage-ment due to their unique mode of action. By priming the plant's innate immune system, these compounds can induce systemic acquired resistance against a broad spectrum of pathogens without directly inhibiting their proliferation. Key advantages of plant activators include prolonged defense activity, lower effective dosages, and negligible risk of developing pathogen resistance. Among the various defensive pathways tar-geted, the salicylic acid (SA) signaling cascade has been extensively explored, leading to the successful devel-opment of commercial activators like benzothiadiazole for widespread application in crop protection. While the action sites of many SA-targeting activators have been preliminarily mapped to different steps along the pathway, a comprehensive understanding of their precise mechanisms remains elusive. This review provides a historical perspective on plant activator development and outlines diverse screening strategies employed across multiple levels, from whole-plant bioassays to molecular and transgenic approaches. We expound on the intricate components, biological relevance, and regulatory circuits governing the SA pathway, while criti-cally examining the structural features, bioactivities, and proposed modes of action of classical activators such as benzothiadiazole derivatives, salicylic acid analogs, and other small molecules. Insights from field trials as-sessing their practical applicability are also discussed. Furthermore, we highlight the current status, challenges, and future prospects in the realm of SA-targeting activator development globally, with a focus on recent en-deavors in China. Collectively, this comprehensive review aims to synthesize existing knowledge and provide a roadmap for future research toward developing more potent and mechanistically understood plant activa-tors that fortify crop immunity against disease.

Analysis of non-stationary and nonlinear sound signals obtained from dynamical processes is one of the greatest challenges in signal processing. Turning machine operation is a highly dynamic process persuaded by many events such as dynamical responses, chip formations and operational conditions of machining. Traditional and widely used fast Fourier transformation and spectrogram is not suitable for processing sound signals acquired from dynamical systems as its result have significant deficiencies because of stationary assumptions and having priori basis. The relatively new technique, Discrete Wavelet Transform, which uses Wavelet decomposition and the recently developed technique, Hilbert Huang Transform (HHT) which uses Empirical Mode Decomposition have notably better properties in the analysis of nonlinear and non-stationary sound signals. This paper presents a comparative study on the decomposition of multicomponent sound signals using Empirical Mode Decomposition and Wavelet Decomposition to highlight the suitability found in HHT to analyze tool-emitted sound signals received from turning processes. Apart from the short mathematical and theoretical foundations of the transformations, this paper demonstrates their decomposition strength using an experimental case study of tool flank wear monitoring in turning. It also concludes HHT is more suitable than DWT to analyze tool-emitted sound signals received from turning processes.

Rheumatoid arthritis (RA) is an autoimmune disease in which joints are gradually de-stroyed, and early diagnosis and treatment before joint deformation or destruction is im-portant. The detection of novel RA biomarkers in saliva may facilitate the early detection of RA before the onset of disease. In this study, we conducted a comprehensive proteomic analysis of salivary proteins from RA model mice. Proteins were identified by Western blotting and enzyme-linked immunosorbent assay in serum, saliva, and ankle joints from DBA/1JJmsSlc mice, a model of rheumatoid arthritis. Ankle joints and submandibular glands were hematoxylin and eosin stained and immunostained, and the results were compared with those of control mice. Citrullinated α1 antitrypsin (A1AT, 46 kDa) was commonly detected in saliva, serum, and ankle joints of severe RA model mice, and was confirmed by proteome analysis. Western blotting detected a band corresponding to 46 kDa in serum, saliva and ankle joints, and immunostaining of ankle joints with A1AT an-tibody showed a strong positive signal in the synovium. In DBA/1JJmsSlc mice, not only cyclic citrullinated peptide antibodies but also A1AT may be involved in protein citrulli-nation and contribute to the development and severity of RA.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

Aquaculture contributes to the sustainable development of food security, marine resource conservation, and economy. Shifting aquaculture feed from fish meal and oil to terrestrial plant-derivatives may result in cost savings. However, many carnivorous fish cannot be sustained on plant-derived materials, necessitating the need for the identification of important factors for farmed fish growth and to investigate whether components derived from terrestrial plants can be used in feed. Herein, we focused on the carnivorous fish leopard coral grouper (P. leopardus) to identify the essential growth factors and clarify their intake timing from feeds. Furthermore, we evaluated the functionality of starch, which are easily produced by terrestrial plants. Results reveal that carbohydrates, which are not considered essential for carnivorous fish, can be introduced as a major part of artificial diet. The development of artificial feed using starch offers the possibility of increasing the growth of carnivorous fish in aquaculture.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

The impact of the agriculture net carbon effect is crucial for climate change mitigation, yet research on this topic in China is currently insufficient. In this study, the carbon balance ratio (CBR) is used to characterise the net carbon effect of agriculture, and the spatial Durbin model and threshold regression model were used to empirically analyse the CBR with a sample of 30 provincial-level regions in China from 2004 to 2019. The aim was to investigate the mechanism of the influence of the land management scale (SCALE) of farming on the CBR. The results of the study indicate that national farming generally has a net sink effect, with large changes in interannual fluctuations; the expansion of SCALE has an obvious role in increasing sinks and reducing emissions, and has a positive spatial spillover effect on CBR, with significant spatial heterogeneity. Furthermore, as the SCALE expands, the direction of the influence of rural residents’ income and education level on CBR changes in the opposite direction, showing a significant non-linear relationship characteristic. However, in most areas, the SCALE threshold has not yet been reached, suggesting that the improvement in education levels can still offset the negative impact of economic income growth in the short term. The study recommends paying attention to the role of farmers’ human capital, changing production methods, and implementing carbon peaking and carbon neutrality goals to enhance the net sink effect of the farming industry, which would be achieved by increasing land management scale.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

The present paper is aimed at presenting an updated review of prediction methods for the aerodynamic noise of ducted rotor-stator stages. Indeed, ducted rotating-blade technologies are in continuous evolution and increasingly used, for both aeronautical propulsion units, power generation and air conditioning systems. Different needs are faced, from the early design stage to the final definition of a machine. Fast-running, approximate analytical approaches and high-fidelity numerical simulations are considered as the best suited tools for each, respectively. Recent advances are discussed, with emphasis on their pros and cons.

High level of noise is a disturbance to the human environment. Noise in industries is also an occupational hazard because of its attendant effects on workers’ health. Noise presents health and social problems in industrial operations, and the source is related to the machineries used in the industries. One of the unique features of the noise associated with wood machinery is the level of exposure and duration. Equipment used in a factory can be extremely loud. They can produce noise at decibels high enough to cause environmental health and safety concerns. The mechanically driven transport and handling equipment, cutting, milling, shaping and dust extractor installations in the wood industry generate noise. The sources of noise pollution have increased due to non-compliance with basic safety practices. The increased use of locally fabricated machine in the industry has increased the level of noise and vibration. The effects of industrial noise pollution as discussed include: increase in blood pressure; increased stress; fatigue; vertigo; headaches; sleep disturbance; annoyance; speech problems; dysgraphia, which means reading/learning impairment; aggression; anxiety and withdrawal. As presented in this paper, noise control techniques include; sound insulation, sound absorption, vibration damping and Vibration isolation.

Introduction: The identification of some prognostic markers in head and neck cancers (HNC) is necessary for the stratification of the therapeutic approach with benefits in increasing treatment response rates and limiting the toxic side effects of treatments. Neutrophil-to-lymphocyte ratio (NLR), lymphocyte-to-monocyte ratio (LMR) and pallets-to-lymphocyte ratio (PLR) are currently validated as cheap and accessible biomarkers in different types of solid tumors. The purpose of the study was to evaluate the possible biomarker value of NLR, PLR and MLR recorded pre-treatment (radiotherapy/chemotherapy) for prognostic purposes in HNC. Materials and methods: The study included 190 patients with HNC included in the oncology record in the oncology outpatient clinic of the Craiova County Emergency Hospital starting from January 2002 and deceased until December 2022. Among them, 40 patients treated multimodally in the Clinic were included in the study of Oncology of the Craiova County Emergency Hospital for which the pre-treatment value (chemotherapy/radiotherapy) of NLR, PLR and MLR could be calculated. Overall survival (OS) values were correlated with NLR, PLR and MLR. Results: Median values for NLR, PLR and MLR were 6.15 (1.24-69), 200.79 (61.3- 1775.0) and 0.53 (0.12-5.5) respectively. In the study, the mean values for NLR, PLR and MLR of 2.88, 142.97 and 0.36 respectively were obtained. Median OS in the study group was 11 months (1-120). Although a negative Pearson`s correlation, the relationship between your variables was only weak, values R =.07, p=.67; R=.02, p=.31 and R=07, p=.62 being related with NLR, PLR and MLR respectively correlation with overall survival (OS). The median values of NLR, PLR and MLR were calculated (1.53, 90.32 and 0.18 respectively) for HNC cases with pre-treatment values of NLR <2 and for HNC cases with NLR values ≥6 (23.5, 232.78 and 0.79 respectively). Median OS for cases with NLR<2 and NLR≥6 were 17.4 and 13 months, respectively. Conclusions: The negative correlations of NLR, PLR and MLR with OS reported in the study are in accordance with the data reported in the literature for locally advanced recurrent and metastatic HNSCC cases. The comparative analysis of the data in the group with NLR<2 and NLR≥6 highlights an advantage of 4.4 months in median OS in favor of the group with low values of NLR. Being cheap and accessible, these markers could change the therapeutic approach even in centers with limited resources. The role of borderline NLR values as a prognostic factor in HNSCC must also be defined. PLR and MLR are less evaluated as biomarkers but the study demonstrates their potential to be used as prognostic biomarkers, it remains to be clarified if their inclusion in multivariable models along with NLR would bring a benefit

In this paper, we introduce new formulas for calculating the restoring and repulsive magnetic forces between two non-coaxial circular loops with parallel axes. These formulas are derived from a modified version of Grover’s formula for mutual inductance between the coils in question. Utilizing these formulas, we compute the restoring and repulsive magnetic forces between two non-coaxial thick coils of rectangular cross-sections with parallel axes. In these calculations, we apply the filament method and conduct investigations to determine the optimal number of subdivisions for the coils in terms of computational time and accuracy. The method presented in this paper is also applicable to all conventional non-coaxial coils, such as disks, solenoids, and non-conventional coils like Bitter coils, all with parallel axes. This paper emphasizes the accuracy and computational efficiency of the calculations. Furthermore, the new method is validated according to several previously established methods

Respiratory syncytial virus (RSV) infection is a major cause of severe respiratory disease in infants and young children worldwide. Two vaccines targeting the elderly and pregnant women have been recently approved employing the prefusion form of the RSV-fusion protein (F). However, there are currently no vaccines for infants. Studies have shown a fusion-inactive prefusogenic F form is significantly more immunogenic and produces higher antibody titers to both the prefusion and postfusion structures of the F protein. Here we have developed RSV virus-like particles (RSV-VLPs) consisting of prefusogenic F, RSV glycoprotein and matrix proteins, produced them using the baculovirus expression system, and studied their protective efficacy in Balb/c mice. Morphology and successful assembly of VLPs were confirmed by transmission electron microscopy and western blot. Mice immunized with VLPs developed high levels of serum IgG and neutralizing antibodies as compared with mice immunized with inactivated virus. The VLP vaccine also induced higher levels of IFNγ and IL4, elicited limited proliferation of CD4+ and CD8+ T cells but higher cytotoxic-T-lymphocyte responses. VLP immunization abolished lung pathology in the mice after RSV challenge. Overall, our results indicate that RSV-VLPs consisting of prefusogenic F, glycoprotein and matrix proteins are a potential vaccine candidate against RSV.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

To date electric pianos and samplers tend to concentrate on authenticity in terms of temporal and spectral aspects of sound. They barely recreate the original sound radiation characteristics, contribute to the perception of width and depth, vividness and voice separation, especially for instrumentalists, who are located in the near field. This paper describes an operational procedure to measure, store, and synthesize the complete sound of a harpsichord, including its spatial sound radiation characteristics. First, actuators excite the instrument at the intersection point of each string with the bridge with an exponential sine-sweep. Then, the radiated sound field is recorded in the near and the far field with microphone arrays. The pressure distribution in the near field is propagated back to the soundboard of the instrument, using Minimum Energy Method. The vibration of each single string is captured with lightweight contact microphones. The soundboard is then replaced by an array of 128 loudspeakers. The loudspeaker signal is a convolution of the back-propagated sweep recording with the string recording to perform a wave field synthesis. Above the spatial Nyquist frequency, the Radiation Method is applied to perform a sound field synthesis which is valid for the listening region of the instrumentalist. The result is an electric harpsichord, that approximates the sound of a real harpsichord precisely in time, frequency, and space domain. Applications for such a radiation keyboard are music performance, instrument and synthesizer building and interactive psychoacoustic research.

Social surveys are conducted to determine how annoyed people are in a certain noise situation. The results are typically presented as exposure-response curves showing the percentage of the area population that are highly annoyed as a function of the noise exposure level. It is a well-known fact that the survey results are not only dependent on the accumulated noise exposure, DNL, DENL, or similar, but also on various other factors such as maximum levels, exposure patterns, noise spectra, etc. A re-analysis of previously reported surveys shows that the results are also to a large extent dependent on survey-specific factors like wording of the annoyance questions, how the questionnaires are presented, response scales, methods of scoring highly annoyed, etc. This paper discusses and quantifies the influence of such factors and suggests ways of comparing results from surveys that have been conducted according to different protocols and different analysis methods.

The urbanisation phenomenon and related cities expansion and transport networks entail preventing the increase of population exposed to environmental pollution. Regarding noise exposure, the Environmental Noise Directive demands on main metropolis to produce noise maps. While based on standard methods, these latter are usually generated by proprietary software and require numerous input data concerning, for example, the buildings, land use, transportation network and traffic. The present work describes an open source implementation of a noise mapping tool fully implemented in a Geographic Information System compliant with the Open Geospatial Consortium standards. This integration makes easier at once the formatting and harvesting of noise model input data, cartographic rendering and output data linkage with population data. An application is given for a French city, which consists in estimating the impact of road traffic-related scenarios in terms of population exposure to noise levels both in relation to a threshold value and level classes.

This paper evaluates the usefulness of measuring the concentration of dissolved hydrogen in an anaerobic fermenter for maintaining the process stability. A laboratory test of two-stage psychrophilic anaerobic digestion of food leftovers from a university canteen was carried out in a vertical reactor with a total working volume of 0.255 m3 without stirring. In the course of the experiment lasting 1050 days, with an average organic loading of 15.45 kgVS m-3 d-1 for the 1st stage and 0.657 kgVS m-3 d-1 for the 2nd stage, a specific biogas production of 0.123 Nm3 per kilogram of substrate and 0.448 Nm3 per kilogram of total solids and 0.480 Nm3 per kilogram of volatile solids, respectively, was achieved. The average methane content in biogas was 55.9 % vol. Slightly higher gas productions were measured in the batch BMP test. The concentration of hydrogen in the mixed biogas from both reactor stages occasionally exceeded 1000 ppm and averaged 134 ppm, the concentration of dissolved hydrogen measured by AMT MS 08 sensor in the overloaded second stage was often 0.10-0.23 mg dm-3 and correlated with the total concentration of lower fatty acids and with the VFA/ TIC parameter. The dissolved hydrogen concentration from AMT instrument was not found to be a reliable timely indicator of overload or process stability.

Integrated crop-livestock production (ILP) is an interesting alternative for more sustainable soil use. However, more studies are needed to analyze soil pore properties under ILP at the micrometer scale. Thus, this study proposes a detailed analysis of soil pore architecture at the micrometer scale in three dimensions. For this purpose, samples of an Oxisol under ILP subjected to minimum tillage (MT) and no-tillage (NT) with ryegrass as cover crop (C) and silage (S) were investigated. The soil micromorphological properties of the soil were analyzed using X-ray microtomography. The MT(C) system showed the highest values of porosity (c. 20.4%), connectivity (c. 32.8×103), volume (c. 26%), and number of pores (c. 32%) in a rod-like shape. On the other hand, the MT(S), NT(C), and NT(S) systems showed higher tortuosities (c. 2.2, c. 2.0, and c. 2.1) and lower pore connectivities (c. 8.3×103, c. 6.9×103, and c. 6.2×103), especially in S use. Ellipsoidal and rod-shaped pores predominated over spheroidal and disc-shaped pores in all treatments. The results of this study show that the use of ryegrass as a cover crop improves soil physical properties, especially in MT. For S use, the type of soil management (MT or NT) did not show any differences.

Aural rehabilitation with hearing aids can decrease the attentional requirements of cognitive resources by amplifying the deteriorated-frequency sound in hearing loss patients and improve the auditory discrimination ability like speech-in-noise perception. As aural rehabilitation with an intelligible-hearing sound also can be hopeful, the aim of this study was to evaluate the effectiveness of the aural rehabilitation with intelligible-hearing sound for hearing loss patients. Adult native Japanese speakers (17 males and 23 females, 68.43±9.23 years) showed over 30 dB at 125, 250, 500, 1000, 2000, 3000, 4000, 8000, 10000, and 12000Hz on any side, were recruited and underwent Mini-Mental State Examination Japanese. we conducted self-evaluation questionnaire for hearing problems of voice, gap detection test, fast speech test, and speech-in-noise test, pure tone audiogram, speech perception test using Japanese 67-S, cortical auditory evoked fields, and magnetic mismatch negativity before and after the non-intelligible-hearing (N=20) and intelligible-hearing (N=20) sound therapy with listening to music for one hour a day for 35 days. Better hearing ear was defined using a four-frequency pure-tone average at the thresholds of 500, 1000, 2000 and 4000 Hz. After the sound therapy, speech-in-noise test with signal to noise ratio +10 in better hearing ear showed significant improvement (p&lt;0.05), and N1m-P2m amplitudes showed the significant increase in Lt superior temporal gyrus at the stimulus from better hearing ear (p&lt;0.05). The significant enhancement of the magnetic mismatch negativity amplitude at Lt superior temporal gyrus was exhibited after the sound therapy (p&lt;0.01). Intelligible-hearing sound therapy can improve the ability of speech-in-noise perception in better hearing ear and the enhancement of central cortex response, which reflect the ability of working memory, was proved by cortical auditory evoked fields and magnetic mismatch negativity. Intelligible-hearing sound therapy can be a valuable aural rehabilitation method for sensory neural hearing loss as same as hearing aids.

Inorganic nanoparticles are utilized for therapeutic, diagnostic, or in combination, theranostic purposes. The latter involves simultaneous sensing, imaging, or tracking of drug delivery. Furthermore, these nanoparticles can differ in their morphologies, which affect outcomes such as the effectiveness of hyperthermia, induction, drug loading, circulation time by escaping the body's immune system, imaging modality clarity, and biosensing. However, design of these theranostics is limited by the lack of a method to predict their therapeutic efficacy. Herein, we report a simple and novel computational approach via algebraic and geometric calculations of surface area (SA) to volume (V) ratios (SA:V) which can help predict the efficacy of the inorganic nanoparticles of the investigated morphologies. The approach comprises a coding platform for the program and uses Python 3 on a Windows 10 operating system. Analyses of 29 polyhedral morphologies that inorganic nanoparticles could assume ex silico showed that only particular concave and convex morphologies in this size regime are more productive over the standard sizes as well as a few noted in literature for baseline comparison. Our results provide a method that can aid in predicting the efficacy of inorganic nanoparticles with certain morphology giving rise to their fundamental basis and eventual implementation ex silico.

High-frequency circuit performance is significantly impacted by impedance variations, particularly within the low-resistance regime. Traditional Ohm’s Law based modeling approaches often fail to accurately predict circuit behavior in these conditions, leading to design inaccuracies and potential system failures. The Standard Ohm’s Law based model’s prediction of infinite current as resistance approaches zero is physically unrealistic and hinders its application in practical scenarios. Despite the recognition of these limitations, existing models have not comprehensively addressed the complex impedance behavior observed in high-frequency circuits. To overcome these challenges, this paper introduces a modified version of the Ohm’s Law incorporating an exponential correction term. The Modified Ohm’s Law’s accuracy was evaluated through simulated experiments across a wide frequency range (1kHz to 1GHz) using various electronic components. The findings demonstrate the superior performance of the modified model in predicting currents under low-resistance and high-current conditions compared to the Standard Ohm’s Law model. By providing finite and accurate current values, the proposed model effectively mitigates the unrealistic infinite current predictions of the standard approach. The enhanced predictive capabilities of the Modified Ohm’s Law hold significant implications for high-frequency circuit design and analysis. Its application can lead to improved performance and reliability in power electronics, telecommunications, and other high-frequency systems. By incorporating non-linear impedance behavior, the model offers a more accurate representation of real-world circuit conditions. Future research should focus on refining the exponential term’s parameters to optimize the model's accuracy across a broader range of applications. Additionally, real-time implementation and hardware validation are essential to assess the model's practical utility in complex circuit environments.

Background: We prepared reference materials of fentanyl and amphetamines in hair, and established methods for the certification of reference materials of fentanyl and amphetamines in hair samples. Methods: Hair samples containing 15 drugs were prepared by immersion method (water-dimethylsulfoxide). On the basis of single-factor experiment, Box-Behnken design-response surface was used to optimize the pre-treatment conditions of samples. In MRM/SIM mode, 15 drugs were quantitatively analyzed by LC-MS/MS and GC-MS/MS methods. Results: The contents of 15 drugs in the mixed hair samples were: 1.050 ng mg-1~7.771 ng mg-1, RSDs&lt;7%(n=11). The results showed that the two analytical methods developed were highly sensitive (LODs as low as 0.05 pg mg-1), reproducible (intra-day and inter-day precision RSDs were&lt;10%) and accurate. F-test was performed on the prepared hair samples and the results showed that the homogeneity of the prepared hair samples was good. Conclusions: The established methods were used for the detection of fentanyl and amphetamine drugs in human hair, with high sensitivity, accuracy and specificity. It can be used as a certified method for the development of fentanyl and amphetamine matrix certified reference materials. The developed hair reference materials are expected to be applied in forensic drug abuse detection and laboratory quality control.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

(1) Background: This retrospective cohort study aimed to investigate the cephalometric evaluation of facial height ratio (FHR) and growth patterns. (2) Methods: We assessed facial height ratios, Y-axis to SN angle, and growth patterns in 94 participants from Timis county using digital cephalograms. Participants were categorized based on Angle’s classification. Cephalograms were digitally traced and analyzed using WebCeph imaging software. Statistical analysis was conducted using Python version 3.11.9. (3) Results: Significant correlations were observed between FHR and craniofacial development, particularly regarding hypodivergent growth patterns. In a sample of 94, molar classes showed varying patterns: Class I—33.3% hyperdivergent, 61.5% normodivergent, 33.3% hypodivergent. Class II—50% hyperdivergent, 30.8% normodivergent, 52% hypodivergent. Class III—16.7% hyperdivergent, 7.7% normodivergent, 14.7% hypodivergent. Y-axis to SN angle values were within normal limits across groups (Group I: 65.0 (IQR: 61.2-69.0), Group II: 65.0 (IQR: 62.0-69.0), Group III: 67.0 (IQR: 59.7- 69.0). A strong negative correlation was found between Y-axis to SN angle and Jarabak’s ratio (r = -0.72, p &lt; 0.001), highlighting the need for holistic assessment methods in orthodontic practice. (4) Conclusion: Patients from Timis county predominantly exhibit a hypodivergent growth pattern across all malocclusion types. Understanding these patterns is essential for comprehensive orthodontic treatment planning. Further research is needed to explore the implications of these findings on treatment outcomes and patient care.

Article explores participant specific study of muscle inherehit dynamics hidden inside the diognostic electromyography (D-EMG) signals during load pull exercises, aiming to uncover underlying patterns and nonlinear behaviors. Employing a multi-step analytical framework, the study first evaluates signal stationarity through Quantile-Quantile (Q-Q) plot and surrogate data analyses, revealing insights into signal stability. Subsequent use of phase space reconstruction techniques exposes intrinsic dynamics within the EMG signals, visualized through Poincar´e maps, elucidating attractor geometry and system dynamics. Histogram analysis further dissects the Poincar´e maps, offering insights into signal behavior relative to physiological processes. Additionally, the study quantifies the largest Lyapunov exponent from the Poincar´e maps, providing a measure of dynamical complexity within the muscle EMG signals during load pull exercises. By integrating these methods, this research sheds light on the nuanced interplay between EMG signals and muscle activity during dynamic exercises, offering valuable insights for rehabilitation strategies.

Recurrent neural networks (RNNs) transmit information over time through recurrent connections. In contrast, biological neural networks use many other temporal processing mechanisms. One of these mechanisms is the inter-neuron delays caused by varying axon properties. Recently, this feature was implemented in echo state networks (ESNs), a type of RNN, by assigning spatial locations to neurons and introducing distance-dependent inter-neuron delays. These delays were shown to significantly improve ESN task performance. However, thus far it is still unclear why distance-based delay networks (DDNs) perform bettern than ESNs. In this paper, we show that by optimizing inter-node delays, the memory capacity of the network matches the memory requirements of the task. As such, networks concentrate their memory capabilities to the points in the past which contain the most information for the task at hand. Moreover, we show that DDNs have more total linear memory capacity, with the same amount of non-linear processing power.

Muscle spindles are encapsulated sensory organs found in most of our muscles. Prevalent models of sensorimotor control assume the role of spindles is to reliably encode limb posture and movement. Here, I argue that the traditional view of spindles is outdated. Spindle organs can be tuned by spinal γ motor neurons that receive top-down and peripheral input, including from cutaneous afferents. A new model is presented, viewing γ motor activity as an intermediate coordinate transformation that allows multimodal information to converge on spindles, creating flexible coordinate representations at the level of the peripheral nervous system. That is, I propose that spindles play a unique overarching role in the nervous system: that of a peripheral signal-processing device that flexibly facilitates sensorimotor performance, according to task characteristics. This role is compatible with previous findings and supported by recent studies with naturalistically active humans. Such studies have so far shown that spindle tuning enables the independent preparatory control of reflex muscle stiffness, the selective extraction of information during implicit motor adaptation, and for segmental stretch reflexes to operate in joint space. Incorporation of advanced signal-processing at the periphery may well prove a critical step in the evolution of sensorimotor control theories.

Machine Learning (ML) approaches have been fruitfully applied to several classification problems of neurophysiological activity. Considering the relevance of emotion in human cognition and behaviour, ML found an important application field in emotion identification based on neurophysiological activity. Nonetheless, the literature results present a high variability depending on the neuronal activity measurement, the signal features and the classifier type. The present work aims to provide new methodological insight on ML applied to emotion identification based on electrophysiological brain activity. For this reason, we recorded EEG activity while emotional stimuli, high and low arousal (auditory and visual) were provided to a group of healthy participants. Our target signal to classify was the pre-stimulus onset brain activity. Classification performance of three different classifiers (LDA, SVM and kNN) was compared using both spectral and temporal features. Furthermore, we also contrasted the classifiers performance with static and dynamic (time evolving) features. The results show a clear increased in classification accuracy with temporal dynamic features. In particular, the SVM classifiers with temporal features showed the best accuracy (63.8 %) in classifying high vs. low arousal auditory stimuli.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

Malassezia is a lipid-dependent genus of yeasts known for being an important part of the skin mycobiota. These yeasts have been associated in the development of skin disorders and cataloged as a causal agent of systemic infections under specific conditions, making them opportunistic pathogens. Little is known about the host-microbe interaction of Malassezia spp., and unraveling this implies the implementation of infection models. In this mini review we present different models that have been implemented in the fungal infections study with greater attention in Malassezia spp. infections. These models range from in vitro (cell cultures and ex vivo tissue), to in vivo (murine models, rabbits, guinea pigs, insects, nematodes, and amoebas). We additionally highlight the alternative models that reduce the use of mammals as model organisms, which have been gaining importance in the study of fungal host-microbe interactions. This is due to the fact that these systems have shown to have reliable results, which correlate with those obtained from mammalian models. Example of alternative models are Caenorhabditis elegans, Drosophila melanogaster, Tenebrio molitor, and Galleria mellonella. These are invertebrates that have been implemented in the study of Malassezia spp. infections in order to identify differences in virulence between Malassezia species.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Abstract: Important variables that affect the quality and functionality of sperm and may affect male reproductive health and fertility include telomere length, mitochondrial content, and the ratio of mitochondrial DNA (mtDNA) to nuclear DNA (nDNA). The purpose of this study was to look at the connections between these three sperm characteristics and how they might affect a woman's ability to conceive. Methods: Data were collected from 82 men who underwent IVF/ICSI at the University Hospital of Ioannina's IVF Unit in the Obstetrics and Gynecology Department. Evaluations included sperm morphology, sperm count, sperm motility, and participant history. To address this, males of reproductive age who were categorized into three body mass index (ΒΜΙ) groups—normal, overweight, and obese—had their sperm samples tested. Results: Our findings indicate a negative correlation between relative telomere length and ΒΜΙ for both the normal and overweight groups. Conversely, a positive correlation was observed for the obese group, indicating a possible relationship between mitochondrial health and telomere maintenance. The results were statistically significant only for the obese group. Furthermore, a negative correlation was observed between telomere length and mitochondrial content in both the normal and overweight groups, indicating that a lower mitochondrial content may be linked to longer telomeres. Nonetheless, there was a positive correlation for the group that was obese. For all three groups, the data did not reach statistical significance. Given that mitochondrial con-centration and telomere length are both markers of cellular integrity and health, these correla-tions may have an impact on the quality of sperm. Furthermore, the relative telomere length of the normal and overweight groups had a negative correlation with the ratio of mtDNA to nDNA, though the obese group showed a positive correlation. The findings were not statistical-ly significant in any of the groups under investigation. According to this, male fertility may be negatively impacted by an imbalance in the copy number of the mitochondrial genome com-pared to the nuclear DNA in sperm. Conclusions: Our research, in essence, emphasizes the interaction among human sperm telo-mere length, mitochondrial concentration, and the mtDNA to nDNA ratio. Gaining knowledge of these correlations could help explain the reasons behind male infertility and open up new treatment options for reproductive health problems. The functional importance of these correla-tions and possible uses in therapeutic contexts require more investigation.

The concept of {\it quantum ratio} emerged in the recent efforts to understand how Newton's equations appear for the center of mass (CM) of an isolated macroscopic body at finite body-temperatures, as the first approximation to quantum-mechanical equations. It is defined as $Q\equiv R_q/L_0$, where the quantum fluctuation range $R_q$ is the spatial extension of the pure-state CM wave function, whereas $L_0$ stands for the body's linear size (the space support of the internal, bound-state wave function). The two cases $R_q /L_0 \lesssim 1$ or $R_q/ L_0 \gg 1$, roughly correspond to the body's CM behaving classically or quantum mechanically, respectively. In the present note we elaborate more on this concept, illustrating it in several examples. An important notion following from introduction of the quantum ratio is that the elementary particles (thus the electron and the photon) are quantum mechanical, even when the environment-induced decoherence turns them into a mixed state. Decoherence and classical state should not be identified. This simple observation, further illustrationed by the consideration of a few atomic or molecular processes, may have significant implications on the way quantum mechanics works in biological systems.