The definition of UTC in 1972 balanced the needs of the time and frequency community for a universal time scale that was traceable to the definition of frequency in the SI system of units with the needs of the astronomical community for a time scale that was closely linked to UT1, a time scale related to the rotation of Earth. The balance between these two considerations has changed very significantly since 1972, and there is widespread agreement that the method of relating UTC to UT1 should be changed by increasing the maximum tolerance between the two scales to more than the current limit of 0.9 s. I propose to realize this decision by means of an algorithmic adjustment process based on the variation in the length of the day over the previous centuries. I use these historical data to extrapolate the length of the day for a century into the future, and to compute a periodic rate adjustment to UTC based on this extrapolation. The adjustment process will not use time steps. The magnitude of the periodic rate adjustment will be re-considered every century, but the basic adjustment algorithm will not change. I suggest a maximum tolerance between UT1 and UTC that is large enough to absorb the irregular and unpredictable variations in the length of the day with respect to the long-term average increase in this value but plays no role in determining the parameters of the adjustment process that is proposed. I also propose that the adjustment be implemented at 12 UTC on 1 January since that is closest to a universal holiday in all time zones.

Magnetoelectric (ME) sensor is a new type magnetic sensor with ultrahigh sensitivity, low power consumption, and suitable for the measurement of low frequency weak magnetic field. In this study, metglas/PZT-5B ME sensor with a mechanical resonance frequency f_res of 60.041 kHz was prepared. It is interesting to note that its magnetic field resolution reaches 0.20 nT at f_res and 0.34 nT for DC field, respectively. In order to measure the ultralow frequency AC magnetic fields, a frequency upconversion technique was employed. Under this technique, a limit of detection (LOD) of AC magnetic field lower than 1 nT at 8 Hz is obtained, and the minimum LOD of 0.51 nT is achieved at 20 Hz. The high resolution ME sensor with sub-pT level is promising in the field of low frequency weak magnetic field measurement technology.

Predictive studies are essential to establish fundamental data for monitoring and controlling Xylella fastidiosa infections in our country. Limited knowledge exists about how Xylella fastidiosa interacts with the plant host's immune system, leaving numerous unanswered questions regarding Xylella fastidiosa biology and its interactions with national plant hosts. Key inquiries include understanding of how the plant immune system interfaces with Xylella fastidiosa in the xylem and identifying the specific or shared mechanisms underlying the susceptibility of different hosts. Factors such as the presence of insect vectors, abundance of host plants, and climate suitability play pivotal roles in Xylella fastidiosa dispersal. We recommend that countries identified with relatively high risk, like Portugal, undertake thorough individual risk analyses. The implementation of preventive measures and, if necessary, the enhancement of surveillance systems for early detection of Xylella fastidiosa in plants and insect vectors are crucial steps. Additionally, raising awareness is of equal importance to mitigate socioeconomic and ecological impacts on their ecosystems.

Identifying cracks in the incipient state is essential to prevent the failure of engineering structures. Detection methods relying on the analysis of the changes in modal parameters are widely used because of the advantages they present. In our previous research, we have found that eigenfrequencies were capable of indicating the position and depth of damage when sufficient vibration modes were considered. The damage indicator we developed was based on the relative frequency shifts (RFS). To calculate the RFSs for various positions and depths of a crack, we established a mathematical relation that involved the squared modal curvatures in the healthy state and the deflection of the healthy and damaged beam under dead mass, respectively. In this study, we propose to calculate the RFS for beams with several cracks by applying the superposition principle. We demonstrate that this is possible if the cracks are far enough from each other. In fact, if the cracks are close to each other, the superposition method does not work and we distinguish two cases: (i) when the cracks affect the same beam face, the frequency drop is less than the sum of the individual frequency drops, and (ii) on the contrary, cracks on opposite sides cause a decrease in frequency, which is greater than the sum of the frequency drop due to individual damage. When the RFS curves are known, crack assessment becomes an optimization problem, the cost function being the distance between the measured RFSs and all possible RFSs for several vibration modes. Thus, the RFS constitutes a benchmark that characterizes damage using only the eigenfrequencies. We can accurately locate multiple cracks and estimate their severity trough experiments and thus prove the reliability of the proposed method.

Environmental, social, and governance (ESG) investment has become a common trend in capital markets, and many institutional investors have publicly declared their long-term ESG investment target (ESGIT). This study focuses on investors who conduct strategic asset allocation (SAA) using composite indices but establish their ESGIT outside the SAA process. A mismatch could arise between investors’ planned and actual portfolios because they must pursue their ESGIT by asset selection, which inevitably makes the constituents of their portfolios different from those of composite indices. To scrutinize the potential existence of a misalignment between their SAA and ESGIT, this study analyzes actual stock and bond indices over the past decade using traditional mean-variance optimization. The results reveal significant differences between the expected and realized performances, and the misalignment is more significant when the analysis period is divided into two sub-periods: stable and volatile. Specifically, the results indicate that the efficient frontier constructed using ESG indices significantly differs from that constructed using composite indices, and that the difference between these two efficient frontiers becomes more significant during volatile periods. Furthermore, the results show that investors cannot meet their targets if their ESGIT is established outside the SAA process.

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

Emerging infectious diseases are a major threat to biodiversity and an important public health issue. West Nile virus (WNV) is an emerging vector-borne zoonotic arbovirus that is currently broadening its distribution in Europe. The evidence of WNV circulating in resident and migratory species has implications for both animal and public health, and should therefore be studied in depth. An integrated surveillance program, namely in birds, is essential for reducing the risk of infection in human populations within the One Health principles. In the present study, wild birds admitted to wildlife rehabilitation centres in Portugal were sampled. Two-hundred and eight blood samples were assayed serologically to antibodies to WNV, by using a commercial ELISA kit. An overall seroprevalence of 19.6% (95% confidence interval [CI]: 13.7-26.7%) was observed. Antibodies to WNV were detected in 13 (35.1%) different species of wild birds. Accipitriformes (26.7%; 95% CI: 18.5-36.2%) and Strigiformes (26.7%; 95% CI: 14.6-42.0%) were the orders with the highest seroprevalence recorded. There were no statistically significant differences (p = 0.725) between the geographical regions (NUTS II) studied, but statistically significant difference (p = 0.017) was found between gender (male: 34.4%; female: 4.8%). A higher seroprevalence was found in adults (32.1%) compared to juvenile birds (9.3%) (p = 0.014), and age was considered a risk factor to WNV infection in wild birds (odds ratio 1.4; 95% CI: 0.5–4.0). More epidemiological studies are needed in Portugal, since the actual spread of the WNV throughout the country is unknown.

The Folla Redonda grape is indigenous to the region of Rias Bajas in Galicia, Spain. This grape is distinguished by its characteristic acid flavor and pulp of remarkable coloration. Despite the wine obtained from this grape is highly valued by consumers of this region for its surprising acidic notes and thickness, it is important to note that it is not a variety of Vitis vinifera and its production is not legally regulated. In the present study, an evaluation of the physicochemical properties of the Folla Redonda grape (pH, °Brix, °Bé, density, acidity, sugar content, etc.) as well as its content in bioactive compounds (total polyphenols and anthocyanins) was carried out. Additionally, the antioxidant potential of the extracts obtained from this grape was demonstrated. This study proved the interesting organoleptic characteristics of the grape, along with a high content of compounds of interest and an important antioxidant activity comparable to that of Vitis vinifera grapes. Therefore, the grape's natural consumption and its application in different industries such as nutraceutical or pharmacological would result in an important revaluation of the grape and significant health benefits. In case that the production of wine from this variety is legalized, consumers will not only be able to enjoy a wine with a characteristic dense reddish color and important acid tones, but also with interesting concentrations of bioactive compounds.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

Whilst prior works have characterised the affordances of prototyping methods in terms of generating knowledge about a product or process, the types, or ‘dimensions’ of knowledge towards which they contribute are not fully understood. In this paper we adapt the concept of ‘design domains’ as a method to interpret, and better understand the contributions of different prototyping methods to design knowledge in new product development. We first synthesise a set of ten dimensions for design knowledge from a review of literature in design-related fields. A study was then conducted in which participants from engineering backgrounds completed a Likert-type questionnaire to quantify the perceived contributions to design knowledge of 90 common prototyping methods against each dimension. We statistically analyse results to identify patterns in the knowledge contributions of different methods. Results reveal that methods exhibit significantly different contribution profiles, suggesting different methods to be suited to different knowledge generation. Thus, this paper indicates potential for new methods, methodology and processes to leverage such characterisations for better selection and sequencing of methods in the prototyping process.

Modern electrical power systems integrate ancillary services to provide security and quality of service in real-time operation because of the intense variations in frequency caused by the massive development and uncertainty of solar-wind generation. Therefore, this ancillary services market focuses on power reserves for secondary and tertiary frequency control. Adjusting reserves and dispatching plants is a manual instruction executed by the system operator to maintain the frequency in the normal operating state (49.80≤f≤50.20 Hz). However, in the absence of an economic model for real-time power reserve reallocation in the ancillary services market, the reserve adjustments made by the system operator are not always optimal since they generate a displacement between the scheduled and actual marginal costs. Then, this work proposes a methodology for operating the ancillary services market in real-time through a dynamic and hourly mathematical model that integrates the variability of solar-wind generation, the demand monitoring curve, and the trajectory of the marginal cost. This model minimizes power reserve costs, which are governed by hourly price auctions, for candidate plants classified as supra/infra-marginal and can optimally reallocate power reserves for secondary and tertiary frequency control.

The precipitation, flocculation, and deposition of asphaltene cause severe formation damage within a reservoir and shorten a well’s productive life. Pressure depletion is one factor that contributes to asphaltene precipitation during production; therefore, the first step in managing asphaltene is to determine the onset pressure of the precipitation. While there are numerous equation of state models that can be used to predict the onset pressure, these models are complex and heavily reliant on tuning parameters. Using multivariate linear regression, this work attempts to develop a simple and accurate thermodynamic model for predicting the upper precipitation onset pressure under pressure depletion above the bubble point pressure (Pb) at various temperatures. A total of 94 experimental data points from 37 published crude oil data sets were compiled from the literature. To develop the model, 59 experimental data points were used as training data and 35 experimental data points as testing data. According to the results of the multicollinearity test, the bubble point pressure, temperature, resins, and saturate-to-aromatic ratio were chosen as predictors. The upper onset pressure data with comparable trends were clustered, and unsupervised recognition of three distinct cluster groups was performed. For each cluster identified, a multivariate linear regression model was developed. The model was chosen based on Mallow’s coefficient of determination (Cp), adjusted R² (statistical measure of fit), and S (standard error of the regression slope). The developed model was tested using a data set, and the results showed an adjusted R² of 96.25%, with a mean absolute error of 4.1%. The model was randomly applied to 15 data points to compare it to perturbed-chain statistical associated fluid theory (PC SAFT) and the Peng-Robinson equation of state models and to the multivariate regression models of Fahim (2007) and Ameli et al. (2016). The results showed that the mean absolute error for predicting the asphaltene precipitation onset pressure was 2.82% using Peng-Robinson, 2.36% using the PC SAFT equation of state, 23.96% using the Fahim model, 24.80% using the model reported by Ameli et al., and 2.39% using the newly developed multivariate regression model. The developed multivariate model appears to be as accurate as the PC SAFT equation of state modeling with tuning parameters. The primary advantage of multivariate regression is that, unlike the PC SAFT equation of state model, it does not require saturates, aromatics, resins, and asphaltenes (SARA)-based characterization methodologies or rigorous parameter tuning. It is simple to use, quick, and it produces results in a short period of time.

Knowing the number of cases of an epidemic is the first function of epidemiological surveillance. An important underreporting of cases was observed in many places during the first wave of COVID-19 pandemic. To estimate this underreporting in the COVID-19 outbreak of Borriana (Valencia Community, Spain), during “Falles” mass gathering events in March 2020, a cross-sectional study was performed in June 2020 querying public health register. Logistic regression models were used. From a total of 468 symptomatic COVID-19 cases diagnosed in the outbreak by anti-SARS-CoV-2 serology, 36 cases were reported (7.7%), thus an underreporting of 92.3% (95% Confidence Interval [CI] 89.5%-94.6%), 13 unreported cases for every reported case. Only positive SARS-CoV-2 polymerase chain reaction cases were predominantly reported due to a limited testing capacity and following a national protocol. Significant factors associated with underreporting were no medical assistance for COVID-19 disease, adjusted odds ratio [aOR] 10.83 (95% CI 2.49-47.11), no chronic illness, aOR=2.81 (95% CI 1.28-6.17), middle and lower social classes, aOR=3.12 (95% CI 1.42-6.85), younger age, aOR=0.97 (95% CI 0.94-0.99), shorter duration of illness, aOR=0.98 (95% CI 0.97-0.99). To improve surveillance, studies of representative population samples are necessary to estimate the magnitude of future epidemics, and novel approaches are recommended.

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

The Galápagos Islands are one of the most emblematic protected areas on the planet, and also one of the most studied. Their main economic activity is tourism, which has grown rapidly in recent years. The increase in tourists is associated with the increase in population and the introduction of invasive species, which puts conservation at risk. This makes adequate management even more necessary and relevant on an international scale, since the economy of Galápagos depends on the good state of conservation of its ecosystems and species. Numerous studies have shown that social factors, rather than physical-natural ones, determine the success or failure of a marine protected area (MPA), so they must be urgently incorporated into all phases of MPA management. In this study we have analyzed the management of the protected areas of Galápagos: the National Park and the Marine Reserve. The methodology used presents five prescribed scenarios in which priority is given to one or other factors, each of which has an impact on biophysical and socio-economic systems that are influenced by the MPA. These scenarios have been called: proactive, interactive, centralized, learning, and formal management. The results show that the archipelago's protected areas follow a proactive management model, with a continuous feedback loop. This feedback is a key element in any adaptive management process, which also allows practitioners to anticipate future problems. Both public participation and strategic planning are essential.

Detecting, especially locating local degradations at an incipient stage, is very important for mission-critical high voltage rotating machines. One particular challenge of the existing testing techniques is that the characteristic of a local incipient defect is not prominent due to various factors such as averaging with the healthy remainder, attenuation in signal propagation, interference, and varied operating conditions. This paper proposes and investigates the frequency domain reflectometry (FDR) technique based on scattering parameter measurement. The FDR result presents the object length, wave impedance, and reflections due to impedance discontinuity along the measured windings. Experiments were performed on two commercial coils with artificially made defects. These defects include turn-to-turn short, surface creepage, loose coils, and local overheating, which are commonly seen in practice. Two practical water pumps in the field were also selected for investigation. The study outcome shows that the FDR can identify and locate both structure and insulation degradations of both shielded and unshielded objects with good sensitivity. This makes the FDR a comprehensive tool for fault diagnosis and aging assessment.

Owing to the nondiffracting, self-accelerating, and self-healing properties, Airy beams of different nature have become a subject of immense interest in the past decade. Their interesting properties have opened doors to many diverse applications. Consequently, the questions of how to properly design spatial manipulation of Airy beams or how to implement them in different setups have become important and timely in the development of various optical devices. Here, based on our previous work, we present a short review on the spatial control of Airy beams, including the interactions of Airy beams in nonlinear media, beam propagation in harmonic potential, and the dynamics of abruptly autofocusing Airy beams in the presence of a dynamic linear potential. We demonstrate that under the guidance of nonlinearity and external potential, the trajectory, acceleration, structure, and even the basic properties of Airy beams can be adjusted to suit specific needs. We describe other fascinating phenomena observed with Airy beams, such as self-Fourier transformation, periodic inversion of Airy beams, and the appearance of spatial solitons in the presence of nonlinearity. These results have promoted the development of Airy beams, and have been utilized in various applications, including particle manipulation, self-trapping, and electronic matter waves.

Paratuberculosis, or Johne's disease, caused by Mycobacterium avium subsp. paratuberculosis (MAP), is a chronic granulomatous enteritis affecting both domestic and wild ruminants. The agent was also found in wild mammals such as wild boar (Sus scrofa), however, the role of wild mammals in the epidemiology of MAP is unclear. During the research period, 941 free-ranging wild boar (S. scrofa) legally hunted in two locations in the Centre-eastern region of Portugal were examined. Ninety-seven wild boar exhibited one or more gross lesions and were tested for the presence of Mycobacterium avium subsp. paratuberculosis using acid-fast staining, mycobacterial culture, poly-merase chain reaction (PCR), and histopathological examination. Forty-five animals (46.4%, 95% CI: 36.5-56.3%) were identified as infected, as indicated by positive results in culture and/or PCR. The findings revealed that the most significant risk factor was being a juvenile compared to year-lings and adults (OR = 10.2, 95% CI: 2.2-48.0). Based on our results, 37.9% (n = 11) of the infected animals were considered suitable for human consumption. Our findings offer novel insights into mycobacterial infections in wild boar populations in Portugal and suggest that wild boar could be a source of human infection if zoonotic potential is considered.

Our goal was to determine the cellular immune response (CIR) among a random sample of the Borriana COVID-19 cohort (Spain) to identify its associated factors and their relationship with infection, reinfection and sequelae. We conducted a nested case-control study using a randomly selected sample of 225 individuals age 18 and older, including 36 individual naïve to SARS-CoV-2 infection, and 189 infected patients. We employed flow cytometry-based immunoassays for intracellular cytokine staining, utilizing Wuhan and BA.2 antigens and chemoluminescence microparticle immunoassay for detection SARS-CoV-2 antibodies. Logistic regression models were used. A total of 215 (95.6%) participants exhibited T-cell response (TCR) to at least one antigen. Positive responses of CD4+ and CD8+ T cells were 89.8% and 85.3% respectively. No difference in CIR was found for naïve and infected patients. Patients who experienced sequelae exhibited higher CIR than those without. A positive correlation was observed between TCR and Anti-Spike IgG levels. Factors positive associated with TCR included A-blood group, number of SARS-CoV-2 vaccine doses received, and Anti-N IgM; factors inversely related were the time elapsed since the last vaccine dose or infection, and B-blood group. These findings contribute valuable insights into the nuance immune landscape shaped by SARS-CoV-2 infection and vaccination.

Gestational diabetes mellitus (GDM) pathophysiology comprises clinical and genetic factors. In fact, GDM has been associated with several single nucleotide polymorphisms (SNPs). This study aimed to build a prediction model of GDM combining clinical and genetic risk factors. A total of 1588 pregnant women from the San Carlos Cohort participated in the present study, 1069 (67.3%) Caucasian (CAU) and 519 (32.7%) Latin American (LAT), 255 (16.1%) with GDM. The incidence of GDM was similar in both groups (16.1% CAU and 16.0% LAT). Genotyping was performed by IPLEX Mass ARRAY PCR selecting 110 SNPs based on literature references. The SNPs showing the strongest likelihood of GDM development were the rs10830963, rs7651090 and rs1371614 in CAU and rs1387153 and the rs9368222 in LAT. Clinical variables including age, pre-pregnancy body mass index and fasting plasma glucose (FPG) at 12 gestational weeks predicted the risk of GDM (AUC 0.648, 95%CI 0.601-0.695 in CAU; AUC 0.688, 95%CI 0.628-9.748 in LAT) and adding the SNPs modestly improved prediction (AUC 0.722, 95%CI 0.680-0.764 in CAU; AUC 0.769, 95%CI 0.711-0.826 in LAT). In conclusion, adding genetic variants enhanced the prediction model of GDM risk in CAU and LAT pregnant women. An RCT is underway to demonstrate its usefulness

Research on Traffic Light Recognition (TLR) has grown in recent years, primarily driven by the growing interest in autonomous vehicles development. Machine Learning algorithms have been widely used to that purpose. Mainstream approaches, however, require large amount of data to properly work, and as a consequence, a lot of computational resources. In this paper we propose the use of Expert Instruction (IE) as a mechanism to reduce the amount of data required to provide accurate ML models for TLR. Given an image of the exterior scene taken from the inside of the vehicle, we stand the hypothesis that the picture of a traffic light is more likely to appear in the central and upper regions of the image. Frequency Maps of traffic light location were thus constructed to confirm this hypothesis. The frequency maps are the result of a manual effort of human experts in annotating each image with the coordinates of the region where the traffic light appears. Results show that EI increased the accuracy obtained by the classification algorithm in two different image datasets by at least 15%. Evaluation rates achieved by the inclusion of EI were also higher in further experiments, including traffic light detection followed by classification by the trained algorithm. The inclusion of EI in the PCANet achieved a precision of 83% and recall of 73% against 75.3% and 51.1%, respectively, of its counterpart. We finally presents a prototype of a TLR Device with that expert model embedded to assist drivers. The TLR uses a smartphone as a camera and processing unit. To show the feasibility of the apparatus, a dataset was obtained in real time usage and tested in an Adaptive Background Suppression Filter (AdaBSF) and Support Vector Machines (SVMs) algorithm to detect and recognize traffic lights. Results show precision of 100% and recall of 65%.

Coastal environments are complex systems that are influenced by a combination of natural processes and human activities. Scientific interest in the effects of coastal erosion/accretion and climatic change-related processes greatly increased in recent decades due to the growing human development along coastal areas. This paper investigates the state and evolution of beach-dune systems for the 1977-2001 and 2001-2019 periods of the Mediterranean coast of Andalusia (Spain) using two different proxies: the dune toe line, which was used to track foredunes evolution, and the high-water line, which was used to assess shoreline evolution. Results showed a general erosional behavior of the studied beach-dune systems and identified cases where the main trend was altered through human interventions. In the 1977-2001 period, 54% of foredunes showed erosion, 24% accretion and 22% stability while and 34% of shorelines showed erosion, 40% accretion and 34% stability. In the 2001-2019 period, 42% of foredunes showed erosion, 28% accretion and 30% stability, and 40% of shorelines showed erosion, 34% accretion and 26% stability. Combining the evolution classes of each proxy (dune toe/shoreline) allows the behavior of both shoreline proxies to be assed together and provides insights additional to those derive from the use of a single proxy. In this regard, Erosion/Erosion (EE) was the most frequent behavior, with 25% and 27% in the first and second periods respectively, and Accretion/Accretion (AA), with 17% in both periods. Erosion of foredunes combined with stability or accretion of the shoreline (ES and EA) were the most common pairings in the first period, while stability of dunes combined with accretion of the shoreline (SA) and Stability/Stability (SS) dominated in the second period. The results obtained provide additional insights on the nature and drivers of coastal change that aid local coastal managers and administrations in understanding erosion processes. The method can be applied at other areas around the world where a similar data base is available.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

A unified critical state model has been developed for both clean sand and silty sand using the modified Cam-clay model (MCC). The main feature of the proposed model is a new critical state line equation in the e-ln(p) plane that is capable of handling both straight and curved test results. With this feature, the error in calculating plastic volumetric strain is eliminated in theory. Another crucial feature of the model is the transformed stress tensor based on the SMP (spatially mobilized plane) criterion, which takes into account the proper shear yield and failure of soil under three-dimensional stresses. Additionally, the proposed model applies the intergranular void ratio with the fines influence factor for silty sand. Only eight soil parameters are required for clean sand, and a total number of twelve soil parameters are needed for silty sand.

A simplified version of the quantum teleportation protocol is presented in here. Its experimental confirmation will have deep implications for a better understanding of Quantum Entanglement with a particular projection on Quantum Communications.

Cervical cancer is one of the ailments that endangers the health of women all over the world and causes infertility. Fortunately, this disease can be avoided. Both the results and participation rates of the current preventative strategy remain poor. Hence, preventative or early detection methods remain challenging and open. In gynecology and computer science fields, few studies on identifying cervical cancer are based on behavior risk factor and machine learning. Moreover, various social and behavioral aspects might often make it more difficult to detect cervical cancer especially in low‑ and middle‑income countries (LMICs). Accordingly, focus on predicting the presence of cervical cancer through behavioral risk factors is the basic structure of this research. We proposed an approach to classify cervical cancer from a social-behavioral perspective using logistic regression to predict cervical cancer. We got significantly improved outcomes than the existing methods. Moreover, we used feature engineering to formulate less dimensionality as a pre-processing step and optimized parameters to be prepared for classification phase. The results proved that using the logistic regression with regularization type L1 had a promising performance. The accuracy of Logistic Regression (LR) L1 was 97.2%. Such results support the proposed work as a reliable classification predictive tool.

The problem of intensification of melt crystal growth process has been analyzed using CdTe as an actual material. Numerical simulation of 100 mm diameter CdTe crystal growth by VGF technique has been carried out. The heat-mass transfer was controlled by introducing of low-frequency oscillating baffle into the melt, so called axial vibrational control (AVC) technique. The baffle configuration has been optimized to destroy solid «tails», which were formed near the crucible walls at high cooling rates due to the low thermoconductivity and the corresponding latent heat. Analysis of CdTe homogeneity range showed that during fast crystal cooling Te micro precipitations were formed resulting from decay of oversaturated Cd-riched nonstoichiometric solid solution at Bridgman crystal growth technique. A VGF grown CdTe crystal after full crystallization stays inside the phase field of the high temperature wurtzite polymorph. This makes it possible to go through the polymorph transition without Te micro-precipitating using the advantages of VGF specific feature of very slow cooling.

Understanding the optimal strategy for a real estate investment and how performance changes based on characteristics is crucial for optimising the achievable return. This is prominent in tourist areas such as Paphos where there is no clear distinction as to whether short or long-term approaches are optimal. The study aimed to develop a model for predicting the optimal rental strategy whilst assessing which model performed best and which property attributes impacted its return the greatest. Short-term data was collected from AirDNA and long-term data was manually collected from real estate agents websites. Furthermore, Random Forest, K-Nearest Neighbour and Multiple Linear Regression models were created to predict the highest and best use for each property. Model accuracy varied between data sets with the best performing model for short-term properties being Random Forest (R-Squared: 0.843), and Distance-Based Multiple Linear Regression for long-term approach (R-Squared: 0.843). The study demonstrated that accurate models could be created to predict the optimal rental strategy with the number of bedrooms being the main driver for rental income, followed by luxury finishes and the presence of a pool. It found that locational characteristics didn’t impact the returns significantly assuming that the property was located within a tourist area.

Multimodal emotion classification (MEC) involves analyzing and identifying human emotions by integrating data from multiple sources, such as audio, video, and text. This approach leverages the complementary strengths of each modality to enhance the accuracy and robustness of emotion recognition systems. However, one significant challenge is effectively integrating these diverse data sources, each with unique characteristics and levels of noise. Additionally, the scarcity of large, annotated multimodal datasets in Bangla limits the training and evaluation of models. In this work, we unveiled a pioneering multimodal Bangla dataset, MAViT-Bangla (Multimodal Audio Video Text Bangla dataset). This dataset, comprising 1002 samples across audio, video, and text modalities, is a unique resource for emotion recognition studies in the Bangla language. It features emotional categories such as anger, fear, joy, and sadness, providing a comprehensive platform for research. Additionally, we developed a framework for emotion recognition that employs a cross-modal attention mechanism among unimodal features. This mechanism fosters the interaction and fusion of features from different modalities, enhancing the model’s ability to capture nuanced emotional cues. The effectiveness of this approach was demonstrated by achieving an F1-score of 0.64, a significant improvement over unimodal methods.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

Different types of disasters, whether natural or human character, lead to the significant loss of human lives. In the latter case, the quick action of identification of corpses and human remains is mandatory. There are a variety of protocols to identify victims, however, genetics is one of the tools that allow an exact identification of the victim. However, several factors may interfere with this identification, from the biological samples’ degradation not allowing the analysis of nuclear information, to failure to dispose of biological samples from family members. Access to certain family members could be a determinant of the proper choice of genetic markers that allow the identification of the victim, or his/her inclusion in a given genetic maternal or paternal lineage. With the new advances in the genetic field, it is expected to allow soon the identification of victims from disasters only with his/her biological postmortem samples, being possible to draw a robot portrait and its most likely physical characteristics. In all cases, genetics is the only modern tool with universal character and can be used in essentially all biological samples, giving and identification of more or less accurate statistical character, depending on whether nuclear or lineage markers are used.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

The genome sequencing of Botrytis cinerea has supplied a general overview of the map of genes involved in secondary metabolite synthesis. B. cinerea genomic data have revealed that this phytopathogenic fungus has seven sesquiterpene cyclase (Bcstc) genes that encode proteins involved in the farnesyl diphosphate cyclization. Three sesquiterpene cyclases (BcStc1, BcStc5 and BcStc7) have been characterized, related to the biosynthesis of botrydial, abscisic acid and (+)-4-epi-eremophilenol, respectively. However, the role of the other four sesquiterpene cyclases (BcStc2, BcStc3, BcStc4 and BcStc6) remains unknown. BcStc3 is a well-conserved protein with homologues in many fungal species, and here, we have undertaken its functional characterization in the life cycle of the fungus. A null mutant ΔBcstc3 and an overexpressed–Bcstc3 transformant (OvBcstc3) were generated, and both strains show deregulation of those other sesquiterpene cyclase-encoding genes (Bcstc1, Bcstc5, Bcstc7). These results suggest a co-regulation of the expression of the sesquiterpene cyclase gene family in B. cinerea. Phenotypic characterization of both transformants revealed that BcStc3 is involved in oxidative stress tolerance, production of reactive oxygen species and virulence. The metabolomic analysis allowed the isolation of characteristic polyketides and eremophilenols from the secondary metabolism of B. cinerea, although no sesquiterpenes different from those already described were identified.

The digital transformation in Industry 4.0 has revolutionized quality control paradigms, integrating advanced technologies such as augmented reality, deep learning, and computer vision systems into a new era called "Quality 4.0". This study systematically reviews how these technologies are shaping new practices in continuous quality supervision and improvement, adapting to increasingly automated and connected production environments. Through a comprehensive analysis of the literature, practical applications in various industrial sectors, from manufacturing and agriculture to the production of sweets and snacks, are highlighted. Additionally, the conceptual and detailed design of a quality control system using artificial intelligence tools is presented, focusing on the inspection of dimensions, color, weight, and labeling of MDF boxes. The proposed system demonstrates an effective integration of sensors, high-definition cameras, and deep learning algorithms, validated through tests with boxes of different sizes. The results suggest that the adoption of these technologies not only improves the accuracy and efficiency of inspections but is also essential to maintaining high-quality standards in a dynamic and competitive industrial environment.

The Eurasian grapevine (Vitis vinifera L.) is the most widely grown horticultural crop in the world and is important for the economy of many countries. In the wine production chain, grape varieties play an important role as they directly influence the authenticity and classification of the product. Identifying the different grape varieties is therefore fundamental for quality control and inspection activities, as well as for regulating production. Currently, ampelography and molecular analysis are the main approaches to identifying grape varieties. However, both methods have limitations. Ampelography is subjective and prone to errors and is experiencing enormous difficulties as ampelographers are increasingly scarce. On the other hand, molecular analyses are very demanding in terms of cost and time. In this scenario, Deep Learning (DL) and Machine Learning (ML) methods have emerged as a classification alternative to deal with the scarcity of ampelographs and avoid molecular analyses. In this study, the most recent and current methods for identifying grapevine varieties using DL classification-based approaches are presented through a systematic literature review. The classification pipeline of the 31 studies found in the literature was described, highlighting its pros and cons. Most of the studies used DL-based models trained with leaf images acquired in a controlled environment at a maximum distance of 1.2 metres to classify grape varieties. In addition, there is a large gap between practical applications and the datasets used: a great lack of varieties, limited data acquired in the field and a lack of tests on plants under adverse conditions. Potential directions for improving this area of research were also presented.

In this article a simplified view is given on Verlinde’s entropic gravity. It reveals several shortcomings in the theory. This holds in particular for the inclusion of the dark matter effect in the derived modified expression for the Newtonian gravitational acceleration. Although the merit of the entropic view on gravity is recognized, the proposed explicit axiomatic hypothesis as a basis is criticized. There is no reason why it should be preferred above Einstein’s Field Equation.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Infrared thermography is a contactless imaging technique, useful to measure surface temperature at distance which has been widely applied in animal production. The possible applications within the pig husbandry include sow heat detection, reduction of the incidence of neonatal mortality, recognition of febrile state caused by pathogens, study of metabolic efficiency, evaluation of stress caused by heat, by constraints, or by aggressive interaction and meat quality prediction. Even if this technique could be easily influenced by environmental factors, the continuous improvement in the procedures and the decrease in the cost of the equipment will allow in the next future new and more applications in swine farming.

The weakness of the dispersion-managed link combined with optical phase conjugation to compensate for optical signal distortion caused by chromatic dispersion and nonlinear Kerr effect of standard single mode fiber is its limited structural flexibility. We propose dispersion map that can simultaneously compensate for the distorted wavelength division multiplexed signal while increasing the configurational flexibility. Each residual dispersion per span (RDPS) in the former half of the proposed link is randomly determined, and in the latter half, the arrangement order of RDPS is the same as or inverted in the former half. We confirm that the dispersion maps in which the RDPS distribution pattern in the latter half is opposite to the arrangement order in the former half are more effective in compensation, and rather, the compensation effect is better than in the dispersion map of the conventional scheme. The notable result of this paper is that the increase of flexibility can be achieved through random arrangement of RDPS in the former half, and the compensation improvement can be achieved by through inverse arrangement in the latter half which make the distribution profile of each half link roughly symmetric with respect to the midway optical phase conjugator.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

The confinement experienced due to the COVID-19 pandemic has prompted a rethink of the teaching-learning process to which teachers have responded without planning and instead using their resources. This study aims to analyze the relationships between work-family interactions, technostress, and perceived organizational support in teachers during the confinement period in Spain that began in March 2020. An online survey was administered to 640 pre-school, primary, and secondary school teachers. Positive reciprocal work-family interactions and their relationship with organizational support were found, with differences according to gender, with women showing a more negative perception of the impact on the family. There were no marked levels of technostress in the overall sample, although higher levels of perceived ineffectiveness and skepticism were found in teachers aged 46 years or older. Teachers in private and subsidized schools showed a higher level of perceived support than those in public schools. There is a need to continue this work to verify the values of these dimensions in other contexts and to apply institutional measures and public policies to improve these indicators in this group.

The climate crisis necessitates a global shift to achieve a secure, sustainable, and affordable energy system toward a green energy transition reaching climate neutrality by 2050. Because of this, renewable energy sources have come to the forefront and the research interest in microgrids which rely on distributed generation and storage systems has exploded. Furthermore, many new markets for energy trading, ancillary services, and frequency reserve markets have provided attractive investment opportunities in exchange for balancing the supply and demand of electricity. Artificial intelligence can be utilized to locally optimize energy consumption, trade energy with the main grid, and participate in these markets. Reinforcement learning (RL) is one of the most promising approaches to achieve this goal because it enables an agent to learn optimal behavior in a microgrid by executing specific actions that maximize the long-term reward signal/function. The study focuses on testing two optimization algorithms: logic-based optimization and reinforcement learning. This paper proposes an optimization algorithm based on reinforcement learning in an industrial microgrid that is capable of trading energy with the main grid, providing significant cost savings. The RL-based approach is implemented in Python based on real data from the site and in combination with MATLAB-Simulink to validate its results. The application of the RL algorithm achieved an average monthly cost saving of 20% compared to logic-based optimization and 86% savings compared to not using any optimization. These findings contribute to digitalization and decarbonization of energy technology and support fundamental goals and policies of the European Green Deal.

Although the influence of climate on the fire regime is unanimously recognized, most publications are studies on this influence are at the global scale. Therefore, this study aims to demonstrate the role of climate in the incidence of wildfires at the country and regional scale using statistical analysis and machine learning methods. Mainland Portugal was chosen as a case study due to its climate and because it is the European region most affected by wildfires. Results demonstrate the climate signature in the spatial and temporal distribution of the wildfire incidence. The conclusions of the study include (i) the existence of two pyro-regions, with different types of climate (Csb and Csa) composed of NUTS II regions: the northern region composed of the Norte and Centro regions and the southern region composed of Alentejo and Algarve; (ii) the intra-annual variability in the incidence of wildfires, characterized by two peaks, one in spring and the other in summer, are a consequence of the country's type of climate; and, (iii) how the annual cycle of wildfire incidence varies over the years depends on the weather conditions throughout each year. These results are of fundamental importance for wildfire managers, especially in the context of climate change.

We present a very computationally light and fast approximation algorithm and then verify it with genetic algorithm and simulated annealing. We show that our algorithm is on par with GA and SA in terms of output produced while having a tightly bounded time complexity. Our algorithm works best when there is a strong positive correlation between the reliability of a component and its cost. We present two algorithms with the same essence. One of them is system cost bounded and the other is target reliability bounded. Our proposed algorithm works on a subsystem level redundancy instead of component level redundancy.

Two decades after the antiretroviral therapy (ART) introduction, several challenges still prevail in maintaining people living with HIV (PLHIV), even with "Test and Treat" and/or "Rapid Start of ART" initiatives, as well as the scale-up of ART worldwide to promote access and adherence to treatment. This review examined articles on ART adherence in Africa between 2016 and 2023, published in English and indexed in PubMed. A total of 16 articles out of 2415 were eligible and included for analyses. Overall, ART adherence rates in SSA regions ranged from 43% to 84%. Rates in the centre of the SSA region ranged from 58% to 80%, in the north from 50% to 83%, in the south from 77% to 84%, in the west from 43% to 60% and in the east from 69% to 73%. Most African countries use the self-report to assess treatment adherence, although unreliable. The main factors with negative influence on ART adherence were comorbidities, lack of motivation, socioeconomic difficulties or side effects. Conclusion: Adherence to ART is a good indicator for controlling the spread of HIV. It is important to overcome the barriers that make it difficult to comply with ART and reinforce the factors that facilitate the accession of medication.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

In the last decades we have experienced great social, cultural, and educational changes, spending more time performing tasks in near vision and less hours in outdoor activities, having more overexposure to digital screens, especially the youngest and increasingly from younger ages. It is common to see cases when performing tasks in near vision the posture or position of the head is not adequate, especially the youngest, being essential to have a correct posture of the head to avoid visual, muscular, or articular problems. We present a procedure to try to control the correct position of the head in real time when performing close-up activities. The aim is to detect the inclination of the head and to know if a bad position is adopted due to a visual problem or simply to inadequate visio-postural habits, warning us of the postural anomaly to correct it.

Background: A new access technique was developed to reduce postoperative adverse events after the extraction of impacted maxillary wisdom teeth. Hence, this study aimed to assess the occurrence of adverse events after extraction of maxillary impacted wisdom teeth using traditional or modified access. Methods: Two different surgical incision designs were used for bilateral wisdom tooth extractions in 30 patients. The traditional incision was performed distal to the second molar in the center of the tuberosity, followed by a buccal releasing incision. After tooth extraction the wound was secured by sutures. The new technique consists of an oblique incision from the distal palatal aspect of the tuberosity towards the buccal aspect of the second molar. After tooth extraction, cyanoacrylate glue was used on the wound. Results: Lower pain was reported by patients at the site treated with the new technique (p<0.01). Edema, postsurgical bleeding, and hematoma were similar in both groups. The surgical time was shorter for the new technique (p<0.01). Conclusions: The new technique applied for the extraction of impacted maxillary wisdom teeth reduced postsurgical pain and the duration of surgery.

Accurate traffic simulation models play a crucial role in developing intelligent transport systems that offer timely traffic information to users and efficient traffic management. However, calibrating these models to represent real-world traffic conditions accurately poses a significant challenge due to the dynamic nature of traffic flow and the limitations of traditional calibration methods. This article introduces a machine learning-based approach to calibrate macroscopic traffic simulation models using real-time traffic video stream data. By leveraging computer vision technologies to extract key traffic parameters from video streams, the approach demonstrated a notable improvement in aligning the generated data from the calibrated simulation model with car sensor data, achieving an average improvement of over 50% compared to the uncalibrated macroscopic model. Moreover, there was a substantial reduction in data drift for the machine learning model integrated into the virtual transport space using vehicle-to-everything technology, resulting in a more than fourfold decrease in the average absolute error of the model.

Leptin, acting centrally or peripherally, has complex effects on cardiac remodeling and heart function. We previously reported that central leptin exerts an anti-hypertrophic effect in the heart via cardiac PPARβ/δ activation. Here, we assessed the impact of central leptin administra-tion and PPARβ/δ inhibition on cardiac function. Various cardiac properties, including QRS du-ration, R wave amplitude, heart rate (HR), ejection fraction (EF), end-diastolic left ventricular mass (EDLVM), end-diastolic volume (EDV), and cardiac output (CO) were analyzed. Central leptin infusion increased cardiac PPARβ/δ protein content and decreased HR, QRS duration and R wave amplitude. These changes induced by central leptin suggested a decrease in the ventricu-lar wall growth which was confirmed by MRI. In fact, the EDLVM was reduced by central leptin, while increased in rats co-treated with leptin and GSK0660, a selective antagonist of PPARβ/δ ac-tivity. In summary, central leptin plays a dual role in cardiac health, potentially leading to ven-tricular atrophy and improving heart function when PPARβ/δ signaling is intact. The protective effects of leptin are lost by PPARβ/δ inhibition, underscoring the importance of this pathway. These findings highlight the therapeutic potential of targeting leptin and PPARβ/δ pathways to combat cardiac alterations and heart failure, particularly, in the context of obesity

In this research paper, design and development of pyramidal horn antenna for J-band application is reported. It is particularly designed for 17 dB gain and half beam width about 25 degrees at 6.93 GHz. Horn aperture, horn axial length and distance from the throat of the antenna to aperture are the main design constraints which are calculated and used for the antenna design and simulation. Beam width in E-plane and H-plane horn is calculated and it is 19.18 dB and 22.86 dB respectively. The reported antenna design shows good performance for J-band in radiometry, satellite, and radar applications.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

Onions are known not only for their culinary importance but also for their nutritional and health-promoting properties. Both properties are closely linked to its content of organosulfur compounds, which account for up to 5% of the dry weight of an onion. Given the importance of these compounds, suitable analytical methods are required for their study. Two techniques should be highlighted in this context: gas chromatography coupled to mass spectrometry (GC-MS), and liquid chromatography coupled to mass spectrometry (LC-MS). In this study, eight different onion varieties were analyzed using two distinct analytical techniques: direct thermal desorption–gas chromatography-mass spectrometry (DTD-GC-MS) and high-resolution mass spectrometry (HRMS) on an LC-ESI-QqTOF instrument. Each method identified 18 different organosulfur compounds, with LC-HRMS targeting non-volatile compounds, such as cysteine sulfoxides, and GC-MS targeting volatiles, such as disulfides and trisulfides. The results obtained were studied using Pearson correlations and principal component analysis. No precise correlation was found between the initial organosulfur compounds in onions and their hydrolysates. Consequently, although GC is one of the most employed techniques in the scientific literature, the use of LC-HRMS or a combination of both techniques may offer a more comprehensive and accurate description of the metabolomic profile of onions.

Detection and measurement of pain are crucial in designing effective pain management interventions to alleviate suffering and prevent functional decline in the medical domain. Traditional methods of pain identification rely on verbal patient reports or observable signs, which can be imprecise or subjective due to variability in patient self-assessments. Hence, there is a pressing need for automated methods to standardize pain measurement procedures. This paper proposes a novel facial expression-based automated pain assessment system as a behavioral indicator for pain evaluation. Our system integrates a fusion structure comprising Convolutional Neural Networks (CNNs) and Tensor-based extended Quantitative Expression Descriptors Analysis (TXQEDA). This innovative approach allows for joint learning of robust pain-related facial expression features from raw facial images, combining RGB appearance with shape-based latent representation. We extensively evaluated our proposed model using the UNBC-McMaster dataset for pain classification and intensity estimation. Our results demonstrate the efficacy of the proposed technique, achieving an impressive accuracy of 99.10% for pain level classification. Furthermore, our system excels in pain intensity estimation, showcasing its potential to provide precise and reliable assessments of pain severity. Overall, our research underscores the importance of automated pain assessment systems in improving patient care and clinical outcomes. By leveraging advanced deep learning techniques and fusion strategies, our proposed model offers a promising approach for standardizing pain measurement procedures and enhancing the quality of pain management interventions.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

Utilizing bioinformatics tools, this study expands our understanding of secondary metabolism in Botrytis cinerea, identifying novel genes within polyketide synthase (PKS), non-ribosomal peptide synthetase (NRPS), sesquiterpene cyclase (STC), diterpene cyclase (DTC), and dimethylal-lyltryptophan synthase (DMATS) families. These findings enrich the genetic framework associ-ated with B. cinerea's pathogenicity and ecological adaptation, offering insights into uncharted metabolic pathways. Significantly, the discovery of previously unannotated genes provides new molecular targets for developing targeted antifungal strategies, promising to enhance crop pro-tection and advance our understanding of fungal biochemistry. This research not only broadens the scope of known secondary metabolites but also opens avenues for future exploration into B. cinerea's biosynthetic capabilities, potentially leading to novel antifungal compounds. Our work underscores the importance of integrating bioinformatics and genomics for fungal research, paving the way for sustainable agricultural practices by pinpointing precise molecular interven-tions against B. cinerea. This study sets a foundation for further investigations into the fungus's secondary metabolism, with implications for biotechnology and crop disease management.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

This longitudinal study aimed to analyze the effects of a team rowing-based training program on physical fitness and anthropometric parameters in female breast cancer survivors (n=40; 56.78±6.38 years). Participants were divided into two groups: one rowed in fixed seat rowing (FSR) boats (n=20; 56.35±4.89 years) and the other in sliding seat rowing (SSR) boats (n=20; 57.20±7.7 years). Both groups engaged in two 75-minute sessions per week for 24 weeks. Significant improvements were observed in both groups in terms of weight (FSR: -1.93 kg, SSR: -1.75 kg), body mass index (FSR: -0.73 kg/m², SSR: -0.67 kg/m²), waist circumference (FSR: -2.83 cm, SSR: -3.66 cm), and hip circumference (FSR: -2.02 cm, SSR: -2.88 cm). Muscle strength improved in lower extremities (jump test: FSR: 2.99 cm, SSR: 3.11 cm) and upper extremities (dominant: FSR: 4.13 kgf, SSR: 4.34 kgf; non-dominant: FSR: 3.67 kgf, SSR: 3.32 kgf). Aerobic capacity also improved, with the SSR group showing a greater increase (FSR: 63.05 m, SSR: 93.65 m). Flexibility tests revealed better results in the SSR group for both dominant (SSR: 1.75 cm vs. FSR: -5.55 cm) and non-dominant limbs (SSR: 1.72 cm vs. FSR: -3.81 cm). These findings suggest that the type of rowing modality can influence physical fitness outcomes, with the SSR group showing superior improvements compared to the FSR group.

This study presents the design and comprehensive 3D multiphysics simulation of a novel microfluidic immunosensor for real-time, non-invasive monitoring of pro-inflammatory biomarkers in human sweat. The patch-like device, designed using COMSOL Multiphysics, integrates magnetofluidic manipulation with direct-field capacitive sensing. The sensor comprises two distinct units: an immunocomplex enhancement unit, employing a series of microcoils to optimize the binding efficiency, reaction kinetics, and homogeneity of biomarker-magnetic nanoparticle (MNP) interactions, thereby enhancing the sensor's specificity; and a layered capacitive sensing unit, designed to concentrate and detect biomarker-tagged MNPs, thus amplifying sensitivity. Simulations of the capacitive sensing unit revealed a substantial sensitivity increase of up to 42.48\% at an 85\% MNP concentration within the detection zone. These findings highlight the potential of the proposed immunosensor for efficient and precise real-time biomarker monitoring, which may facilitate early disease diagnosis and enable personalized healthcare interventions.

: A comprehensive analysis was performed, considering blockchain technology (BT) proprieties in digital health, addressing medico-legal, privacy, and regulatory considerations. Adherence to personal data protection and healthcare regulatory guidelines were analyzed and compared for GDPR (Europe), HIPAA (United States), CCPA (California), PIPEDA (Canada), Privacy Act of 1988 (Australia), APPI (Japan), and LGPD (Brazil). Issues such as Health Systems, Strengthening and aligning policy orientations and initiatives, and emphasizing the role of data analysis in shaping health policies were explored. The study addressed conflicts between the legal frameworks and blockchain, comparing and suggesting solutions like revision of laws and integration of com-pliance mechanisms. Additionally, it sought to enhance IT-health literacy by integrating healthcare and legal domains. Ongoing collaboration between legal, health, and IT experts is essential for designing systems that effectively balance privacy rights and data protection while maximizing the benefits of disruptive technologies like blockchain.

This paper aims to provide the smart grid research community with an open and accessible general mathematical framework to develop and implement optimal flexibility mechanisms in large-scale network applications. The motivation of this paper is twofold. On the one hand, flexibility mechanisms are currently a hot topic of research, which is aimed to mitigate variation and uncertainty of electricity demand and supply in decentralised grids with a high aggregated share of renewables. On the other hand, a large part of such related research is performed by heuristic methods, which are generally inefficient (such methods do not guarantee optimality) and difficult to extrapolate for different use cases. Alternatively, this paper presents an MPC-based (Model Predictive Control) framework explicitly including a generic flexibility mechanism which is easy to particularise to specific strategies such as Demand Response, Flexible Production and Energy Efficiency Services. The proposed framework is benchmarked with other non-optimal control configurations to better show the advantages it provides. The work of this paper is completed by the implementation of a generic use case which aims to further clarify the use of the framework and thus, to ease its adoption by other researchers in their specific flexibility mechanisms applications.

This paper investigates the use of deep learning techniques to perform energy demand forecasting. Specifically, the authors have adapted a deep neural network originally thought for image classification and composed of a convolutional neural network (CNN) followed by a multilayered fully connected artificial neural network (ANN). The convolutional part of the network was fed with a grid of temperature forecasting data distributed in the area of interest in order to extract a featured temperature. The subsequent ANN is then fed with this calculated temperature along with other data related to the timing of the forecast. The proposed structure was first trained and then used in a real setting aimed to provide the French energy demand forecast using ARPEGE forecasting weather data. The results show that the performance of this approach is in the line of the performance provided by the reference RTE subscription-based service, which opens the possibility to obtain high accuracy forecasting using widely accessible deep learning techniques through open-source machine learning platforms.

Real-time object detection remains a pivotal topic in the realm of computer vision. Balancing the accuracy and speed of object detectors poses a formidable challenge for both academic researchers and industry practitioners. While recent transformer-based models have showncase the prowess of the attention mechanism, delivering remarkable performance improvements over CNNs, their computational demands can hinder their effectiveness in real-time detection tasks. In this paper, we elect to use YOLOX as our robust starting point and introduce a series of effective enhancements, culminating in a new high-performance detector named YOLOAX. To further exploit the power of the attention mechanism, we devise multi-dimensional attention-based modules that activate CNNs, emphasizing the most pertinent regions and bolstering the capacity to learn the most informative image representations from feature maps. Moreover, we introduce a novel leading label assignment strategy called STA, along with a groundbreaking loss function named GEIOU Loss, to further refine our detector's performance. We provide extensive ablation studies on the COCO and PASCAL VOC 2012 detection datasets to validate our proposed methods. Remarkably, our YOLOAX is trained solely on the MS-COCO dataset from scratch, without leveraging any prior knowledge, which achieves an impressive 54.2% AP on the COCO 2017 test set while maintaining a real-time speed of 72.3 fps, surpassing YOLOX by a significant margin of 3.0% AP. Our source code and pre-trained models are openly accessible at https://github.com/KejianXu/yoloax.

Modern fighter aircraft increasingly need to conjugate aerodynamic performance and low observability. In this paper we showcase a methodology for a gradient-based bidisciplinary aero-stealth optimization. The shape of the aircraft is parametrized with the help of a CAD modeler, and we optimize with the SLSQP algorithm. The drag, computed with the help of a RANS method, is used as the aerodynamic criterion. The stealth criterion, a function is derived from the radar cross section in a given cone of directions, weighed with a function whose goal is to cancel the electromagnetic intensity in a given direction. Stealth is achieved passively by scattering back the electromagnetic energy away from the radar antenna and no energy is absorbed by the aircraft, which is considered as a perfect conductor. A Pareto front is identified by varying the weights of the aerodynamic and stealth criteria. The Pareto front allows for an easy identification of the CAD model corresponding to a chosen aero-stealth trade-off.

The development of the automotive industry leads to the improvement of the designs of automatic transmissions and drives and to the development of methods for monitoring and diagnosing their condition. The trend of improving transmissions comes down mainly to the endless improvement of existing designs of CVTs and variators, which inevitably leads to the complication of designs and methods for their control and diagnostics.There is a need to create a fundamentally new simplified gearbox based on the scientific achievements of mechanics. However, the created structures remained inoperable due to the lack of theoretical justification.The adaptive gear variator developed by the author, which has CVT functions, is a mechanism with two degrees of freedom and with an additional constraint of a fundamentally new type, called a force - speed constraint. The force - speed constraint imposes a force restriction on the movement of links, while maintaining the number of degrees of freedom in the kinematics. Monitoring the state of the developed gearbox in the form of a non-switchable gear variator is greatly simplified, since the largest number of faults occur in the control system, and there is no control system in the gear variator. It seems possible to apply the digital twin method to diagnose the developed simplified CVT.The proposed article is devoted to a theoretical description of a fundamentally new adaptive gearbox, created on the basis of the latest achievements in mechanics, with the prospect of developing a simplified monitoring and diagnostic system for it

Welded structures are subjected to internal residual stress after manufacturing that may affect the structural strength and normally are associated with an increase on initial geometrical imperfections. This study presents a simplified method to generate an adequate representation of residual stresses on Finite Element models for structural analysis of thin-walled structures and other applications. The results obtained shown that the methodology proposed to introduce residual stresses is simple, accurate and efficient on the modulation of post-welding stresses and their pattern, thus it may be used for simulation of the thermal process.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Models of subsurface structures are important for successful deposit exploration but are challenged by the need to integrate data from different geophysical methods. In the present study, we evaluated a method of joint inversion in which audio-magnetotelluric (AMT) and dual frequency induced polarization (DFIP) data sets are inverted simultaneously to produce a consistent 2D resistivity model to show a clear image of subsurface structures. To achieve the objectives, we conducted AMT and DFIP surveys first on the same survey line within the Dongjun lead-zinc deposit in inner Mongolia by developing 31 AMT survey sites with an interstation separation of 40 m on a 1440 m survey track and operated in fifty-three frequencies in the range 1–10,400 Hz to record the resistivity distribution of subsurface to depths exceeding 800 m. The same survey setup up was applied to the DFIP method by utilizing the SQ-3C model with a pole-dipole array configuration and conducted measurements at frequencies of 4 Hz and 4/13 Hz. We first separately inverted AMT and DFIP measurements. The two-dimensional (2D) model obtained from AMT data revealed distinct low resistivity anomalies in the middle of the 2D inversion model. In contrast, the DFIP inversion model showed a high resistive body in the same region. In response to the discrepancies observed in the separate 2D inversion models, we implemented a joint inversion for both the AMT and DFIP datasets. The joint inversion resistivity model shows surficial conducting bodies and a high conductive body along the profile with relatively high Percent Frequency Effect (PEF) indicating high chargeability. The final joint inversion resistivity model clearly images the large silica alteration zone and the Pb-Zn mineralization. This study demonstrates the feasibility of a joint inversion methodology and highlights the value of integrating geophysical methods through joint inversion for enhanced characterization and exploration of lead-zinc ores.

Conventional cancer clinical trials can be time-consuming and expensive, often yielding results with limited applicability to real-world scenarios and presenting challenges for patient participation. Real-world data (RWD) studies offer a promising solution to address evidence gaps and provide essential information about the effects of cancer treatments in real-world settings. Defining RWD based on its original intent, which is the collection of data at the point of care for clinical purposes, can distinguish it from conventional clinical trial data. RWD can be generated using experimental designs that resemble those used in conventional clinical trials, but with several advantages, such as improved efficiency and a better balance between internal and external validity. RWD can support pharmacovigilance, insights into disease progression, and the development of external control groups. Prospective RWD collection enables evidence generation based on pragmatic clinical trials (PCTs) that support randomized study designs and expand clinical research to the point of care. To ensure the quality of real-world studies, it is crucial to implement auditable data abstraction methods and develop new incentives to capture clinically relevant data electronically at the point of care. The treatment landscape is constantly evolving, with the integration of front-line immune checkpoint inhibitors (ICIs), either alone or in combination with chemotherapy, affecting subsequent treatment lines. Real-world effectiveness and safety in underrepresented populations, such as the elderly, patients with poor performance status (PS), hepatitis, or human immunodeficiency virus-infected patients, are still largely unexplored. Similarly, the cost-effectiveness and sustainability of these innovative agents are important considerations in the real world.

The development of biofuels and biodiesel industry specifically, has resulted in the generation of large amounts of glycerol as a surplus. The conversion of glycerol, into chemicals with indus-trial interest, through anaerobic fermentation using E. coli as a biocatalyst is an attractive alter-native to improve economic performance in the biodiesel industry, for example through the bi-otransformation of residual glycerol into ethanol. For 2019, the size of the global ethanol market was valued at $ 89.1 billion US dollar. Biodiesel can be produced from several materials like rapeseed, palm, soya, corn, palm kernel, frying oil or olive-pomace oil (OPO). The last, can be extracted from alperujo, byproduct of olive oil process. However, olive-pomace oil converting into biodiesel is not enough established to achieve a global olive-oil/biodiesel derived process with minimized waste generation. Traditionally biodiesel production process produces an equivalent of 10% by mass of glycerol as a waste or by-product. This work explores the conver-sion of residual glycerol into chemicals like ethanol and hydrogen with a focus on projecting raw material potential availability from OPO, contributing to the promotion of the use of biofu-els and biodegradable compounds.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

The systematic sampling is used as a method to get the quantitative results from the tissues and the radiological images. Systematic sampling on real line (R) is a very attractive method within which the biomedical imaging is consulted by the practitioners. For the systematic sampling on R, the measurement function (MF) is occurred by slicing the three-dimensional object equidistant systematically. The currently used covariogram model in variance approximation proposed by [28,29] is tested for the different measurement functions in a class to see the performance on the variance estimation of systematically sampled R. This study is an extension of [17], and an exact calculation method is proposed to calculate the constant λ(q,N) of confidence interval in the systematic sampling. The exact value of constant λ(q,N) is examined for the different measurement functions as well. As a result, it is observed from the simulation that the proposed MF should be used to check the performances of the variance approximation and the constant λ(q,N). Synthetic data can support the results of real data.

The purpose of this longitudinal study was to determine the effects of a rowing training program on physical fitness and body composition in female breast cancer survivors (56.78 ± 6.38 years). Over six months, the participants (n=40) performed two training sessions per week for an average of 75 minutes, combining resistance and muscle strength exercises with rowing. To evaluate the impact of the program, physical fitness tests and anthropometric measurements were carried out before and after the training protocol. The results show statistically significant improvements in measures such as weight (-1.84 kg), BMI (-0.7 kg/m2), hip (-3.24 cm) and waist circumference (-2.45 cm). In addition, variables associated with physical fitness also improved including leg strength (3.04 cm), dominant handgrip strength (4.24 kgf), non-dominant handgrip strength (3.49 kgf), aerobic endurance (78.35 m) and muscle flexibility (3.96 cm). We can therefore conclude that a rowing-based exercise program is an effective strategy to improve physical fitness in this type of population, yielding improvements in both anthropometric measurements and basic physical capacity variables, essential factors for better health and quality of life.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

This paper presents the results of aerodynamical performance research focused on maintaining the thermal comfort and increasing the energy efficiency of a typical social housing unit located in a high-density urban area. Bioclimatic design strategies are used to develop a sustainable and economic technology in existing housing clusters in Mexico City. A full-scale prototype, built on campus facilities, was used to study the flow conditions around the design. All scaled prototypes implement similar criterion. Furthermore, a scaled prototype is evaluated within a low speed wind tunnel installation. Additionally, numerical simulations were performed at transient state based on previous physical measurements and historical local climatic conditions to determine preferable modifications.

Recurrent pregnancy loss (RPL) affects around 2 % of women of reproductive age. Primary RPL is defined by ≥2 pregnancy losses and no normal birth delivery. In secondary RPL, the losses are after a normal pregnancy and delivery. Most cases have no clear aetiology, although primary cases are the most complex. Several gene polymorphisms have been associated with RPL. Some polymorphisms are increased in women of Asian or Caucasian race. In admixed RPL populations, the information on possible genetic links is scarce and contradictory. The study aimed to assess the frequency of two SNP in different enzymes involved in medical conditions observed during pregnancy. Microsomal epoxy hydrolase (mEPH) is involved in detoxifying xenobiotics. It is present in ovaries, and it is hormonally regulated. The endothelial nitric oxide synthase forms nitric oxide from arginine and is involved in vascular tone. Two SNPs, rs1051740 and rs1799983, were assessed. The study included 26 controls and 63 primary RPL patients. Significant differences were observed in the frequencies of both SNP (p<0.05). The frequency of mutated alleles was higher in patients. Double mutated homozygotes were encountered only in RLP patients (p<0.05). Genetic polymorphisms rs1051740 and rs1799983 may be involved in primary RPL in the Venezuelan admix population. Genetic studies could provide crucial information on the aetiology of primary RPL.

The paper examines the various uncertainties encountered in high-frequency trading (HFT) environments and delves into the multiple challenges faced by HFT firms in navigating the Dodd-Frank Wall Street Reform and Consumer Protection Act (referred to as the "Dodd-Frank Act"), particularly during the initial stages of its enactment. These challenges include the ambiguity surrounding the definition of HFT, the lack of clarity regarding regulatory requirements and boundaries, inconsistencies in enforcement resulting from deviations in understanding the content, and the absence of detailed descriptions of the Act’s provisions. These hurdles significantly impact not only the daily operations of HFT firms but also pose higher demands on their long-term strategic planning and risk management. Drawing upon the Data, Information, Knowledge, Wisdom, and Purpose (DIKWP) model, this study employs an innovative analytical framework. Through the comprehensive application of conceptual space, cognitive space, and semantic space, it provides a systematic methodology for identifying and analyzing the aforementioned issues. This approach not only aids firms in better comprehending and adhering to complex regulatory requirements but also enables them to explore new business opportunities and competitive advantages while ensuring compliance.

Introduction. Autopsy is a medical procedure that consists of the corpse’s examination to determine the cause of death and obtain information on pathological conditions or injuries present in the body. In recent years there has been a reduction in hospital autopsies and an increase in forensic autopsies. Material and methods. A retrospective observational study was conducted on the reports of all the 645 hospital autopsies performed at Polyclinic of Bari from 2006 to 2021.Results. Group A, 2006-2009, 174 cases were studied: 58% male, 58% adults, 55% neonatology, pulmonary disease was the cause of death in 23%, and 55% of discrepancy between clinical and autopsy diagnosis. Group B, 2010-2013, comprised 119 cases: 52% male, 46% infants, 48% neonatology, pulmonary disease was the cause of death in 25%, and 56% of discrepancy between clinical and autopsy diagnosis. Group C, 2014-2017, comprised 168 cases: gender equality, 37% infants, 25% gynecology, pulmonary disease was the cause of death in 24%, and 58% of discrepancy between clinical and autopsy diagnosis. Group D, 2018-2021 comprised 184 cases: 56% male, 38% adult, 32% gynecology, pulmonary disease was the cause of death in 27%, and 58% discrepancy between clinical and autopsy diagnosis.Conclusion. The study of hospital autopsies at the Polyclinic of Bari shows that the discrepancy between clinical and autopsy diagnosis is around 56.75%. Thus, the hospital autopsy is helpful in the modern age, especially for diagnosing fetal and neonatal diseases.

Identifying fake news on the media has been an important issue. This is especially true considering the wide spread of rumors on the popular social networks such as Twitter. Various kinds of techniques have been proposed for automatic rumor detection. In this work, we study the application of graph neural networks for rumor classification at a lower level, instead of applying existing neural network architectures to detect rumors. The responses to true rumors and false rumors display distinct characteristics. This suggests that it is essential to capture such interactions in an effective manner for a deep learning network to achieve better rumor detection performance. To this end we present a simplified aggregation graph neural network architecture. Experiments on publicly available Twitter datasets demonstrate that the proposed network has performance on a par with or even better than that of state-of-the-art graph convolutional networks, while significantly reducing the computational complexity.

Angola is vulnerable to climate change, as most of its agriculture is rain-fed and repre-sents the backbone of the people of the southern region of the country, and many peo-ple’s livelihoods depend on it. All crops can suffer from the impacts of climate change, which can lead to challenges in agricultural production and food security in different regions of the world. The work consisted of a systematic review of the impacts of climate change on agriculture in Angola, particularly in the southern region. To achieve this objective the PRISMA2020 methodology was used, using the flowcharts for the selection of studies evaluated from the databases that are: Scopus and Web Sci-ence, resulting in 431 documents published between 1996 and 2023, and of these only 63 were included in the systematic review, with inclusion and exclusion criteria. Research on the short and long-term effects of climate change impacts in agriculture in Angola and in particular the southern region is scarce and insufficient. Temperatures are pre-dicted to rise and precipitation generally decreases over time (approximately -2% by 2100), with the southern region experiencing a stronger drop in precipitation. Agri-culture in Angola will be hit hard and some models show that agricultural productiv-ity will be up to 7% lower by 2050 owing to climate change.

The implementation of systems condition monitoring is of utmost importance in ensuring effective maintenance, optimal efficiency, and adherence to established design criteria. This research presents a novel and economically efficient Digital Twin Model (DTM) designed for the purpose of Live Condition Monitoring (LCM) and Predictive Lifecycles. This study discusses the enhancement of DTs modelling by decreasing the number of dimensions from five to three: Physical, Digital, and Connection entities. The resulting model exhibits a notable improvement in accuracy and efficiency. The suggested Dynamic Time Model (DTM) enhances the empirical pre-set average load for both simulation and experimentation by 35.7%, which is equivalent to a 1.6-fold increase. The DTM demonstrates a significant enhancement in the empirical predefined average lifecycles of the system, as shown in the real-life case study. Specifically, the DTM achieves a 12-fold improvement compared to the simulated results and a nine-fold improvement compared to the experimental findings. The suggested Dynamic Time Management (DTM) demonstrates a significant enhancement in the average lifecycles of the system, with a 19.7% improvement (equivalent to 1.2 times greater) compared to the wireless DTM results obtained through the application of the real system load. The suggested Dynamic Time Warping (DTW) method's accuracy and efficiency are shown via a practical case study using the suspension system of a Peugeot 3008 vehicle.

Background: Pediatric mallet finger injuries lack specific treatment guidelines, necessitating an exploration of effective techniques. Our aim was to evaluate the outcomes of the extension block technique in adolescent mallet finger management. Methods: A comprehensive retrospective analysis was conducted involving 36 adolescents who underwent surgery between 2014 and 2022. Ishiguro’s extension block pinning technique was the primary method employed. Treatment outcomes were evaluated using Crawford's criteria, and complications were also assessed. Results: Bone union was achieved in all cases with a mean union time of 42 days (range: 30-92 days). According to Crawford's criteria, 27 cases (75%) were classified as excellent, 5 cases (14%) as good, and 4 cases (11%) as fair. Minimal complications were observed, including three cases (8%) of superficial infections, one case (3%) of dermal necrosis, and another rare instance (3%) of osteomyelitis. No cases of poor outcomes or significant long-term complications were noted. The average follow-up period was 8.6 months (range: 2-42 months). Conclusions: Ishiguro’s extension block technique is a promising surgical option for adolescent mallet fingers. Its adoption could enhance pediatric orthopedic care, offering a valuable child-friendly treatment alternative.

Background: This study assesses the effects of the ‘Radiant’ image enhancement technique on fetal nuchal translucency (NT) measurements during first trimester sonographic ex-ams. Methods: A retrospective analysis of 263 ultrasound images of first trimester midsagittal sections was conducted. NT measurements were obtained using a semi-automatic tool. Statistical methods were applied to compare NT measurements with and without ‘Radi-ant’ enhancement. An in-vitro setup with predefined line distances provided additional data. Results: Incremental increases in NT measurements were observed with varying levels of ‘Radiant’ application: An average increase of 0.19 mm with ‘Radiant min’, 0.24 mm with ‘Radiant mid’ and 0.30 mm with ‘Radiant max.’ The in-vitro results supported these findings, showing consistent effects on line thickness and measurement accuracy, with the smallest mean deviation occurring at the ‘Radiant mid’ setting. Conclusions: ‘Radiant’ image enhancement leads to significant increases in NT measure-ments. To avoid systematic biases in clinical assessments, it is advisable to disable ‘Radi-ant’ during NT measurement procedures. Further studies are necessary to corroborate these findings and to consider updates to the NT reference tables based on this technology.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

The complex dynamics of the neocortex, the outermost layer of the brain, have been a subject of intense research in neuroscience. Recent studies have suggested that magnetic fields generated by neuronal activity may play a significant role in neocortical dynamics. This paper presents a simplified mathematical model that explores the hypothesized interactions between magnetic dynamos, nondissipative systems, Hamiltonian equations, and the Lorenz force in the context of neocortical dynamics. The proposed model is based on a set of coupled Hamiltonian equations inspired by the Lorenz system, a well-known chaotic dynamical system. The generalized coordinates in the model represent the magnetic field components, while the generalized momenta are related to the electric field components or other relevant quantities. The Hamiltonian equations describe the conservative dynamics of the system, and the coupling terms in the equations are interpreted as representing the interactions between the magnetic and electric field components, analogous to the Lorenz force in electromagnetism. The model is implemented using Python, and the Hamiltonian equations are numerically solved using the odeint function from the scipy.integrate module. The resulting dynamics of the magnetic field components are visualized using matplotlib. While the model is highly simplified and does not capture the full complexity of neocortical dynamics, it serves as a starting point for investigating the potential role of magnetic dynamos and Lorenz force interactions in the brain. The paper discusses the limitations of the current model and highlights the need for further refinements, such as incorporating more realistic biological constraints, considering energy dissipation and compensation mechanisms, and validating the model against experimental data. Future work should focus on developing a more comprehensive and biologically plausible model that integrates the latest findings from neuroscience, physics, and computational modeling. By presenting this simplified Hamiltonian model, the paper aims to stimulate further research and discussion on the potential significance of magnetic dynamos and Lorenz force interactions in neocortical dynamics. The model provides a framework for exploring these hypothesized mechanisms and may guide future experimental and theoretical investigations in this emerging field of neuroscience

This study proposes a cephalometric analysis that can be used for biomechanical simulation by considering the important and complex relationship between craniofacial morphology and masseter muscle (MM) size and inclination and by including muscle values. The MM line of action drawn between the Gonion (Go) and Orbital (Or) point relative to dental and skeletal references (occlusal and Frankfort planes) were analyzed. A total of 510 pre-treatment lateral cephalometric tracings (217 males, 293 females, 6-50 years) and lateral Bolton standard tracings (6-18 years) were analyzed. The study examined the following: a) skeletal-cutaneous class (linear distance in mm between the projections of points A' and B' on the occlusal plane), b) the angle between the perpendicular line to the occlusal plane and the Go-Or line at the molar occlusal point, and c) the angle between the Go-Or line and the Frankfort plane. The skeletal classes of the patients ranged from -14.5 to 15.5 mm and did not differ by sex or age; the angle between the Go-Or line and the normal to the occlusal plane averaged 39° (range 15° to 53°) and decreased with age, while the angle between the Go-Or line and the Frankfort plane averaged 42° (range 30° to 54°), increased in older patients. No effect of gender was observed. The two angles were also significantly correlated with each other, but not with sagittal jaw discrepancy. Similar results were obtained with Bolton tracings; the positional relationship of the Go-Or line to the teeth and skeletal landmarks is partially consistent with the literature. The present cephalometric analysis can be usefully used to estimate the mechanical advantage of MM in biomechanical simulations of masticatory muscle performance.

Hybrid power plants have recently emerged as reliable and flexible electricity generation stations by combining multiple renewable energy sources, energy storage systems (ESS), and fossil-based output. However, the effective operation of the hybrid power plants to ensure continuous energy dispatch under challenging conditions is a complex task. This paper proposes a dispatch engine (DE) based on mixed-integer linear programming (MILP) for the planning and management of hybrid power plants. To maintain the committed electricity output, the dispatch engine will provide schedules for operation over extended time periods as well as monitor and reschedule the operation in real-time. Through precise prediction of the PV and wind power output, the proposed approach guarantees optimum scheduling. The precise prediction of the PV and wind power are achieved by employing a predictor of Feed-Forward Neural Network (FFNN) type. With such a dispatch engine, the operational cost of the hybrid power plants, and the use of diesel generators (DGs) are both minimized. A case study is carried out to assess the proposed dispatch engine feasibility. A real-time measurement data pertaining to load, wind, and PV power outputs is obtained from different locations in the Sultanate of Oman. The real-time data is utilized to predict the future output power from PV and the Wind farm over 24 hours. The predicted powers are then used in combination with a PV-Wind-DG-ESS-Grid hybrid plant to evaluate the performance of the proposed dispatch engine. The proposed approach is implemented and simulated using MATLAB. The results of the simulation reveal the proposed Feed-Forward Neural Network’s (FFNN) powerful forecasting abilities. In addition, the results demonstrate that adopting the proposed DE can minimize the use of DG units and reduce plant running expenses.

In recent years, in order to serve as effective solutions to outdoor human thermal environments under the influence of urban heat islands, adaptation measures such as awnings, louvers, directional reflective materials, mist sprays, and evaporative materials have been developed. In this study, a simplified evaluation framework for adaptation measures to urban heat islands is examined. Adaptation measures to urban heat islands are classified into the following three categories; measures to reduce solar radiation incident on the human body, measures to control and cool ground and wall surface temperature, and measures to control and cool air temperature and human body. Case studies are conducted to evaluate the effects of the implementation of cool water circulation sunshade and to examine the adverse effects of cool pavements on the human thermal environment, in addition to the effects of mist sprays on the human body. The effect of the sunshade, watering road, and mist spray, which are typical adaptation measures to urban heat islands, on the human thermal environment was estimated using Wet Bulb Globe Temperature (WBGT) as an indicator for heat stroke prevention and Standard New Effective Temperature (SET*) as an indicator for thermal comfort assessment.

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

Genome-scale metabolic models (GEMs) have been widely used for phenotypic prediction of microorganisms. However, the lack of other constraints in the stoichiometric model often leads to a large metabolic solution space inaccessible. Inspired by previous studies that take allocation of macromolecule resources into account, we developed a simplified Python-based workflow for constructing enzymatic constrained metabolic network model (ECMpy) and constructed an enzyme-constrained model for Escherichia coli (eciML1515) by directly adding a total enzyme amount constraint in the latest version of GEM for E. coli (iML1515), considering the protein subunit composition in the reaction, and automated calibration of enzyme kinetic parameters. Using eciML1515, we predicted the overflow metabolism of E. coli and revealed that redox balance was the key reason for the difference between E. coli and Saccharomyces cerevisiae in overflow metabolism. The growth rate predictions on 24 single-carbon sources were improved significantly when compared with other enzyme-constrained models of E. coli. Finally, we revealed the tradeoff between enzyme usage efficiency and biomass yield by exploring the metabolic behaviors under different substrate consumption rates. Enzyme-constrained models can improve simulation accuracy and thus can predict cellular phenotypes under various genetic perturbations more precisely, providing reliable guidance for metabolic engineering.

Fluorescence-linked immunosorbent assay (FLISA) is a commonly used, quantitative technique for detecting biochemical based on antigen–antibody binding reactions using a well-plate platform. With the developments in the manufacturing technology of microfluidic systems, FLISA can be implemented onto microfluidic disk platforms, which allows the detection of trace biochemical with high resolutions. Apart from requiring a lower proportion of reagent (1/10), this method also reduces the time required for the entire process to less than an hour. The incubation process involves antigen–antibody binding reactions as well as the binding of fluorogenic substrates to target proteins. The protocol for FLISA on a microfluidic platform necessitates the appropriate execution of liquid reagent movements during each step in order to ensure sufficient binding reactions. Herein, we propose a novel microfluidic disk comprising a 3D incubation chamber. Vascular endothelial growth factor as concentration with ng mL-1 is detected sequentially using a benchtop process employing this 3D microfluidic disk. The 3D microfluidic disk is implemented without requiring manual intervention or additional procedures for liquid control. During the incubation process, microbead movement is controlled through centrifugal force, generated due to disk rotation, and gravitational force via bead sedimentation on the sloped floor of the chamber.

In this paper we will present a simplified approach for extracting the ground level – a digital terrain model (DTM) – from the surface provided in a digital surface model (DSM). Most existing algorithms try to find the ground values in a digital surface model. Our approach works the opposite direction by detecting probable above ground areas. The main advantage of our approach is the possibility to use it with incomplete DSMs containing much no data values which can be e.g. occlusions in the calculated DSM. A smoothing or filling of such original derived DSMs will destroy much information which is very useful for deriving a ground surface from the DSM. Since the presented approach needs steep edges to detect potential high objects it will fail on smoothed and filled DSMs. After presenting the algorithm it will be applied to a test area in Salzburg and compared to a terrain model freely available from the Austrian government.