This paper presents an improved indoor localization system based on RF and ultrasonic signal which we named SNSH system. This system composes of a transmitter mounted in a mobile target, and a series of receiver nodes which are managed by a coordinator. By measuring Time Delay of Arrival (TDoA) of RF and ultrasonic signal from the transmitter, distance from target to receiver node is calculated and sent to the coordinator through CAN network, and all the information are gathered in PC to estimate 3D position of the target. Sine wave detector and dynamic threshold filter are applied to provide excellent accuracy of range measurement from TDoA result, and multilateration algorithms is realized to optimize coordinate determination accuracy. Specifically, Linear Least Square and Non-linear Least Square techniques are implemented to contrast their performances in target coordinate estimation. RF signal encoding/decoding time, time delay in CAN network and math calculating are carefully considered to ensure optimal system performance and get ready for field application. Experiments show that sine wave detector algorithm has greatly improved range measurement accuracy, with mean error at 2.2mm and maximum error at 6.7 mm, for distance below 5m. In addition, 3D position accuracy is greatly enhanced by multilateration methods, with mean error in position stay under 15mm, and 90% confident error values at 23mm for LLS, 20mm for NLS. Overall system update period has been verified in real system operation, with maximum rate at 25ms, and compared with other existing researches.

Dearth of information on extent of genetic variability in cassava limits the genetic improvement of cassava in Sierra Leone. This study aimed at assessing the genetic variability and relationships within 103 cassava genotypes using agro-morphological and culinary markers. A field trial was conducted in the School of Agriculture and Food Sciences research site. The experiment was laid in an augmented randomized block design. Morphological classification based on qualitative and quantitative traits categorized the germplasm into three different groups. A total of ten principal components (PCs) in the qualitative and six PCs in the quantitative trait sets accounted for 66.74% and 67.27% of the total genetic variation, respectively. Traits with significantly strong and positive correlations included presence of fruit (PFRT) and presence of seed (PSE)(r = 0.86***),root yield per plant (RYPP) and number of storage root (NSR) (r = 0.76***), RYPP and number of commercial root (NCR) (r = 0.68***), length of leaf lobe (LLL) and width of leaf lobe (WLL) (r = 0.66***),and between NSR and NCR (0.84***). Cooking time, cooking percentage, texture, mealiness, taste and aroma varied widely among the accessions. Findings established that the cassava germplasm possess useful genetic variability that could be exploited through selection for short term release programme, genetic conservation of valuable germplasm and genetic improvement of the crop.

Space-based gravitational wave detection is extremely sensitive to disturbances. The Keplerian configuration cannot accurately reflect the variations in spacecraft configuration. Planetary gravitational disturbances are one of the main sources. Numerical simulation is an effective method to investigate the impact of perturbation on spacecraft orbits. This study shows that, in the context of the Taiji project, Earth’s gravity is an essential factor in the change in heliocentric formation configuration, contributing to the relative acceleration between spacecrafts in the order of O(10−6)m·s−2. Considering 00:00:00 on October 27, 2032 as the initial orbiting moment, under the influence of Earth’s gravitational perturbation, the maximum relative change in armlengths and variation rates of armlengths for Taiji is 1.6×105km, 32m·s−1 respectively, compared with the unperturbed Keplerian orbit. Additionally, by considering the gravitational perturbations of Venus and Jupiter, the armlength and relative velocity for Taiji are reduced by 16.01% and 17.45%, respectively, compared with when only considering that of Earth. The maximum amplitude of the formation motion indicator changes with the orbit entry time. Results show that the relative velocity increase between the spacecrafts is minimal when the initial orbital moment occurs in July. Moreover, the numerical simulation results are inconsistent when using different ephemerises. The differences between ephemeris DE440 and DE430 are smaller than those between DE440 and DE421.

The study investigated farmers’ perception on pests and diseases management strategies, agricultural practices, production constraints and selection criteria of elite varieties using a survey research design. A total of 700 questionnaires were administered to smallholder farmers who were farming for household consumption, those producing for sale and household consumption and those who were mainly producing for sale because their primary goal was to produce for the market. Findings revealed that the most prevalent pests identified were whiteflies (Bemisia tabaci), grasshoppers (Zonocerus variegatus), aphids (Aphis gossypii), mealybugs (Phenacoccus manihoti), termites (Isoptera), and grasscutters (Thryonomys swinderianus). The three most common diseases of cassava limiting growth and yield with mixed infection include viral, bacterial, and fungal. The study also revealed that only 12.5% of farmers cultivated improved cassava varieties. The management practices implemented encompassed field sanitation and the application of pesticides. Lack of capital and no availability of market were the most important production and marketing constraints faced by farmers in the study area, whereas poundability and high storage root yield are the most preferred traits farmers consider in selecting a new variety. Results suggest that smallholder farmers should endeavor to undergo various developmental programs to develop themselves to increase their competitive advantage in their locality and in the local and global agricultural sectors. In addition, governments and other policy makers should strategize plans and programs that would contribute to smallholder farmers’ agriculture, community and national development.

The complex adaptive systems (CAS) research study investigates into the theoretical link of a sustained economic growth as a critical pathway to lift people out of poverty and improve their quality of life. The results show a left-skewed global behavior of an economy-driven human development of 189 countries with 20% or 27 countries obtaining low human development; 80% or 162 countries obtaining medium to very high human development of which 21.16% or 39 countries with medium HDI, 53 or 28.04% or 53 countries with high HDI, and 31.22% or 59 countries with very high HDI. Using the Log (GDP) for visual transformation, closer investigation into the scatterplot diagram reveals that there are also bimodal patterns where countries in the high amplitude and low amplitude groups obtained different human development outcomes despite less or more on economic growth variances mirror on the government policy priorities resulting in four differentiating conditions. Very few countries experience virtuous cycles where both growth and human development are successful; few countries with vicious cycles where both are weak; and many countries with lopsided conditions where the economy is strong but human development is weak, or conversely ones where human development is strong but the economy is weak. The global pattern of economy and human development illustrated by an upward sinusoid or sine wave refutes the conventional linear approach. Uniquely and most importantly, the sinusoidal wave illustrates a decreasing amplitude and decreasing periods as countries manifest apparently complex behaviors that emerge as a result of often nonlinear spatio-temporal interactions among a large number of component systems at different levels of organizations and governments leading to an emergence of a behavior characterizing of a complex adaptive system.

Genetic diversity is very important in crop improvement. This study was carried out to assess the genetic diversity and the number of unique multilocus genotypes (MLGs) in cassava collection in Burkina Faso. To achieve this objective 130 cassava accessions were genotyped using 32 simple sequence repeat (SSR) markers. The results revealed that among these markers, twelve (12) were highly informative, with the PIC values greater than 0.50, twelve (12) were moderately informative, with the PIC values ranged between 0.25 and 0.50, and eight (8) were not very informative, with the PIC values lower than 0.25. A moderate level of genetic diversity was found for the population, indicated by the average expected heterozygosity (0.45) and the observed heterozygosity (0.48). About 83.8% of unique multilocus genotypes were found in the cassava collection indicating that SSR markers seem to be most appropriate for MLGs identification. Population structure analysis based on hierarchical clustering identified two subpopulations and Bayesian approach suggested five clusters. Additionally, DAPC analysis separated the cassava accessions into 13 subpopulations. The comparison of these results and the previous study using SNP, suggest that each type of markers can be used to assessment the genetic structure of cassava grown in Burkina Faso.

: With the increase in demand for non-dairy starter cultures and probiotic bacteria as carriers, the use of legumes (also called pulses) as an alternative has gained momentum. In this study, we investigated the diversity of bacterial communities in samples of pigeon pea (Cajanus cajan L. Millsp.) soaked in water for 12 h and 24 h. We soaked 500 g of pigeon pea in sterile distilled water at room temperature (± 25 °C) for 12 h and 24 h; 10 mL of the soaking water was then collected to measure the bacterial diversity using a metataxonomic analysis. The V1–V9 regions on the 16S ribosomal RNA gene were amplified using 27F and 1492R primers under specific polymerase chain reaction conditions for the bacterial identification. Genomic DNA (130 ng) was sequenced on a R9.4 flow cell by Oxford Nanopore Technologies using a GridION sequencer. Library preparations were initiated using a Native Barcoding Kit 24 V14 (SQK-NBD114.24). Primary data were acquired using MinKNOW version 22.05.7. A total of 13 bacterial families and 89 genera were identified in the pigeon pea sample soaked for 12 h; 26 families and 90 genera were identified in the pigeon pea sample soaked for 24 h. Among the bacterial families identified, the five predominant families in both samples were Enterobacteriaceae, Erwiniaceae, Yersiniaceae, Pectobacteriaceae, and Lactobacillaceae. According to the relative abundance of the identified bacterial genera, the following nine genera were predominant in both samples: Enterobacter, Klebsiella, Citrobacter, Pantoea, Kosakonia, Pseudoenterobacter, Pluralibacter, Leclercia, and Kluyvera. At a genus level, a slight increase in the abundance of Klebsiella, Kosakonia, and Pluralibacter and a slight decrease in the abundance of Citrobacter were observed after prolonged incubation from 12 h to 24 h. The values of five diversity indices revealed that the sample soaked in water for 24 h had a richer bacterial abundance and diversity than the 12 h sample. Shannon and Simpson values revealed a higher bacterial diversity in the sample collected at 24 h than the sample collected at 12 h. Species observations and abundance-based coverage estimator (ACE) values demonstrated that the sample collected at 24 h harbored a higher bacterial richness than the sample collected at 12 h. These findings indicated that the bacterial diversity in the pigeon pea samples increased with the soaking time. The bacterial communities during the soaking of the pigeon pea samples were dominated by the Enterobacteriaceae family and Enterobacter genus. The presence of bacterial genera such as Lacticaseibacillus, Lentilactobacillus, and Secundilactobacillus was notable because of their importance as starter cultures for fermented plant-based milk products, including pigeon pea beverages for lactose-intolerant individuals or individuals with malnutrition.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

Wave and tidal energy, recognized as vital renewable resources, harness the ocean's kinetic and potential power. This study aims to provide an in-depth patent analysis of the technological landscape within these sectors. We applied a dual approach: first, a descriptive analysis was conducted to explore patent publication trends, technology lifecycle stages, patent activity by country, top assignees, and IPC classifications. Our analysis provided a detailed overview of the sector's growth and the key players involved. Second, we utilized topic modeling, specifically BERTopic enhanced with large language models (LLMs), to identify and fine-tune key technolog-ical themes within the patent data. In this study, we identified seven distinct clusters each for wave and tidal energy using this approach. This method led to a novel categorization of the pa-tents, revealing latent themes within the patent data. Although our categorization differs from traditional methods, it provides deeper insights into the thematic focus of the patents, highlight-ing emerging trends and areas of innovation within wave and tidal energy technologies to better exploit and optimize ocean energy conversion infrastructure.

This paper presents the perturbation theory for the double–sine–Gordon equation. We obtain a system of differential equations that shows the amplitude and phase modulation of the approximate solution.. In the particular case λ = 0 we get the well-known perturbation theory for the sine–Gordon equation. For a special value λ=-1/8, we derive a phase-locked solution with the same frequency of the linear case. In general we obtain both coherent (solitary waves, lumps and so on) solutions as well as fractal solutions. We can demonstrate the existence of envelope wobbling solitary waves, because of the phase modulation depending on the solution amplitude and on the position. The main conclusion is that it is too reductive focus only on coherent solutions for the double sine-Gordon equation, because of the very rich behavior for the DSG nonlinear equation, including wobbling chaotic and fractal solutions.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

High Efficiency Video Coding (HEVC) uses an 8-point filter and a 7-point filter, which are based on the discrete cosine transform (DCT), for the 1/2-pixel and 1/4-pixel interpolations, respectively. In this paper, discrete sine transform (DST)-based interpolation filters (IF) are proposed. The first proposed DST-based IFs (DST-IFs) use 8-point and 7-point filters for the 1/2-pixel and 1/4-pixel interpolations, respectively. The final proposed DST-IFs use 12-point and 11-point filters for the 1/2-pixel and 1/4-pixel interpolations, respectively. These DST-IF methods are proposed to improve the motion-compensated prediction in HEVC. The 8-point and 7-point DST-IF methods showed average BD-rate reductions of 0.7% and 0.3% in the random access (RA) and low delay B (LDB) configurations, respectively. The 12-point and 11-point DST-IF methods showed average BD-rate reductions of 1.4% and 1.2% in the RA and LDB configurations for the Luma component, respectively.

Underwater visual detection technology plays a pivotal role in fields such as marine exploration. With the increasing demand for underwater monitoring, the quest for efficient and reliable methods for underwater target recognition has become particularly significant. To address this requirement, this study developed an innovative underwater object detection architecture based on YOLOv8, named YOLOv8-MU, aimed at significantly enhancing detection accuracy.By integrating the LarK module proposed in UniRepLKNet to optimize the backbone network, YOLOv8-MU aims to achieve a larger receptive field without increasing the model’s depth. Further, this research introduces C2fSTR, an innovative method that combines Swin Transformer with the C2f module. Additionally, we have incorporated the SPPFCSPC_EMA module, which combines Cross-Stage Partial Fast Spatial Pyramid Pooling (SPPFCSPC) with attention mechanisms, significantly improving the detection accuracy and robustness of various biological targets. Moreover, by introducing a fusion block based on DAMO-YOLO into the neck of the model, we further enhanced the model’s capability in multi-scale feature extraction. Finally, the adoption of the MPDIoU loss function, designed around vertex distance, effectively tackles the challenges of localization accuracy and boundary clarity in underwater organism detection. Experimental results on the URPC2019 dataset demonstrate that the YOLOv8-MU model achieved an [email protected] of 78.4%, marking improvements of 5.6%, 1.1%, and 4.0% over YOLOv5s, YOLOv7, and YOLOv8n respectively, indicating the leading performance (SOTA) of this method. On the other hand, further evaluation on the URPC2020 dataset confirmed the generalization capability of the YOLOv8-MU architecture, with its [email protected] reaching 80.4%, surpassing various models including YOLOv5x and YOLOv8n, showcasing the wide applicability of our proposed improved model architecture.

This paper, based on the "Unified Theory of Forces," rigorously proves the formula of de Broglie's wave function. This helps us better understand the following important issues: 1) Theoretically prove and understand the essence of de Broglie's wave function; 2) Prove that when the particle's momentum P is determined, the greater the mass of the particle, the more concentrated its wave function distribution, and the weaker the interference effect; 3) Correct the spatial distribution of the wave function of free particles, proving that the wave function of free particles is strictly constrained within a finite spatial range, which is consistent with the facts we observe.

We approximate the trigonometric function sine and cosine on the interval . This analysis provides two formulas to approximate sine and cosine. At first, we try to derive the formula which involves a square root, and then we derive another formula that does not require any use of a square root. Nevertheless, after deriving the procedure which requires no square root, we further try to increase its accuracy and then derive another formula that approximates trigonometric functions more accurately on the interval [0, pi/2]. So, this analysis provides mainly two types of procedures. One uses square roots, whereas the other does not. We also focus on ensuring the accuracy of these trigonometric functions in the interval [0,pi/2]. This accuracy analysis is portrayed using the graph. This graph shows the difference between the values generated by the functions defined here and the actual value of these functions. So, these graphs also indicate the error of these functions on that interval. Finally, we compare our approximation with the approximation formula of the 7th-century Indian Mathematician Bhaskara I.

We developed a novel hybrid approach for solving global optimization, computer science, bio-medical and engineering real life applications that is based on the coupling of the Whale Optimizer and Sine Cosine Algorithms via a surrogate model. We relate the whale optimizer algorithm to balance between the exploitation and the exploration process in the proposed method. There exist confirmed techniques for searching approximate best optimal solutions, but our algorithm will further guarantee that such numerical and statistical solutions satisfy physical bounds of the standard and real life functions. Our experiments with the benchmark, bio-medical, computer science and engineering real life problems have illustrated the advantages of using a newly hybrid approach based on mixing Whale Optimizer and Sine Cosine algorithms. It holds considerable potential for reducing execution time for solving standard and real life problems and at the same time improving the quality of the solution.

The study of underwater vehicle wake detection is of significant importance within the field of target detection, localisation and tracking of underwater vehicles. Given that propellers are the propellers of modern ships and underwater vehicles, the propeller wake field represents the principal target source for wake detection in underwater vehicles. The objective of this paper is to propose a method for measuring the wake of an underwater propeller based on a position-sensitive detector. A theoretical model of the relationship between the laser spot displacement and the change of refractive index of the wake field is established on the basis of the principle of laser beam deflection. A prototype experimental setup for underwater propeller wake measurement was constructed based on the aforementioned optical measurement method. Furthermore, the simulation of the propeller wake flow field with strong density stratification and linear density stratification was conducted based on the experimental setup. In the experiment, a three-bladed propeller with a diameter of 39mm was selected, the water tank size was 980mm×380mm×380mm, and the laser acted at a distance of 550 mm from the propeller. The experimental results indicate that the wake dissipation time of the propeller in a strong density-stratified water environment is approximately 800s. Following the stabilization of the wake field density, the laser spot position is observed to be stable at 0.341 mm, with a corresponding refractive index change of 2.99×10-6 RIU. The wake dissipation time of the propeller in a linear density-stratified water environment is approximately 750 s. Once the wake field density has reached a stable state, the laser spot position is found to be 0.441mm, corresponding to a refractive index change of 3.87×10-6 RIU. These experimental results are found to be in general agreement with the simulation results of the propeller wake field. A comparison of the experimental device-based wake measurements with the CTD-based wake measurements reveals a consistent trend.

The Jiangmen Underground Neutrino Observatory (JUNO) is a 20 kton liquid scintillator multi-purpose underground detector, under construction near the chinese city of Jiangmen, with data taking expected to start in 2021. The main goal of the experiment is the neutrino mass hierarchy determination, with more than three sigma significance, and the high precision neutrino oscillation parameters measurements, detecting electron anti-neutrinos, emitted from two near-by (baseline of about 53 km) nuclear power plants. Besides, the unprecedented liquid scintillator type detector performance in target mass, energy resolution, energy calibration precision and low-energy threshold, features a rich physics program for the detection of low-energy astrophysical neutrinos, such as galactic core-collapse supernova neutrinos, solar neutrinos and geo-neutrinos.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Coconut is an important multipurpose crop wherein different stages of its maturity are used for different products. Traditional approach of its classification use sound formed by tapping the fruit, and the tapper will base its judgment through the sound he heard. The procedure was highly subjective and attempts had been made by other researchers to automate and classify the adulthood of the coconut objectively. Nowadays, deep learning techniques are being utilized to solve classification problems. One such method is Convolutional Neural Network (CNN) that takes raw pixel data, learns to extract features, and ultimately classifies the input. In this study, a portable device was developed that takes audio signals generated from tapping the fruit mechanically. This audio clip was converted to spectrogram and was used as input to a LeNet CNN architecture. We argue that CNN classifier has improved accuracy compared to the non-deep learning system. Our evaluation confirmed that the use of CNN had improved the accuracy of classifying coconut by about 15%.

In the paper, the author finds bounds of the sine and cosine along a circle on the complex plane in terms of two double inequalities for the norms of the sine and cosine along a circle on the complex plane.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

Photon-counting Computed Tomography (PCCT) is a promising cardiovascular-imaging technique. Using detectors that count the number and energy of photons in multiple bins, PCCT offers several advantages over conventional CT, including a higher image quality, reduced contrast agent volume, radiation doses, and artifacts. Although PCCT is well established for cardiac imaging in assessing coronary artery disease, its application in vascular imaging remains limited. This review summarizes the available literature and provides an overview of the current use of PCCT for the diagnosis of vascular conditions. Of the 13 records selected in the initial search, 7 articles were included in the present review: 6 cohort studies and 1 case report. This review synthesized the available literature on PCCT in vascular imaging, focusing mainly on endoleaks detection and characterization after endovascular aneurysm repair (EVAR), contrast dose volume, and radiation exposure reduction, particularly in patients with chronic kidney disease and in those requiring follow-up CT.

Determining the estrous cycle stages in mice is essential for optimizing breeding strategies, synchronizing experimental time lines, and facilitating studies in behavior, drug testing, and genetics. It is critical for reducing the production of genetically unmodified offspring in the generation and investigation of genetically modified animal models. An accurate detection of the estrus cycle is particularly relevant in the context of the 3Rs—Replacement, Reduction and Refinement. The estrous cycle, encompassing the reproductive phases of mice, is key to refining experimental designs and addressing ethical issues related to the use of animals in research. This study presents results from two independent laboratories on the efficacy of the Mouse Estrus Detector (MED) from Elmi Ltd. (Latvia) for the accurate determination of the estrus phase. The female mice of five strains/stocks (CD1, FVB/N, C57Bl6/J, B6D2F1, and Swiss) were used. The results showed that the MEDProTM is a low -traumatic, simple, rapid and painless method of estrus detection that supports the principles of the 3Rs. The use of the MEDProTM for estrus detection in mice caused minimal stress, enhanced mating efficiency, facilitated an increase in the number of embryos for the in vitro fertilization and allowed the production of the desired number of foster animals.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

: This work introduces the instrument design of the medium energy proton detector (MEPD, detection range: 30keV-5MeV) mounted on the Chinese Fengyun-4B (FY-4B) satellite. Compared with the similar detector on the Fengyun-3E (FY-3E) satellite, the instrument has undergone significant changes due to the different orbital radiation environment and solar lighting conditions. Based on the calculation of radiation model AP8, the geometry factor is reduced to 0.002 cm2sr, while the MEPD on FY-3E satellite is 0.005 cm2sr. Another difference is that sensors in some directions is exposed to direct sunlight for 80 minutes every day on this orbit, depending on the attitude angle of the satellite, which is much worse than that on FY-3E satellite. According to the calculation results of permeability of photons through different materials, a 100 nm thickness nickel film is added in front of sensors in order to eliminate light pollution completely. The experiment on the solar simulator shows that the measure is effective and the detector has no error counts when the solar irradiance coefficient is 1.0. In addition, Geant4 software is applied to simulate particle transportation process under complete machine condition so that to check the contamination of electrons on sensors among all directions after magnetic deflection. Data obtained in orbit shows that the instrument works properly, and the data is in good agreement with the AP8 model. The observations of the MEPD on board the FY-4B satellite can provide important support for the safety of the spacecraft and the theoretical research related to space weather.

We demonstrate the use of a nanotechnology-based approach for the investigation of enzymatic activity of a single molecule of horseradish peroxidase with a solid-state nanopore. The artificial 5 nm solid-state nanopore has been formed in a 40-nm-thick silicon nitride structure. Single molecule of HRP has been entrapped into the nanopore. The activity of horseradish peroxidase (HRP) enzyme molecule inserted in the nanopore has been monitored by recording the time dependence of the ion current through the nanopore in the course of the reaction of 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonate) (ABTS) oxidation reaction. We have found that in the process of ABTS oxidation in the presence of 2.5 mM hydrogen peroxide, individual HRP enzyme molecules are able to retain activity for approximately 700 seconds before a decrease in the ion current through the nanopore, which can be explained by structural changes of the enzyme.

Smart sensors based on graphene field effect transistor and biologically receptors are regarded as a promising nanomaterial that could be the basis for future generations of selective real-time monitoring of target analytes and smaller electronics. So the purpose of this paper is to provide details a real-time and selective explosive sensor based on GFETs and PDA-based lipid membranes coupled with biologically inspired TNT peptide receptors. Following an introduction, this paper describes the way of fabrication of the GFETs device by investigation methods for transferring graphene sheet from Cu substrates to target substrates, which is functionalized by the TNT peptide receptors, in order to offer a system which has the capability of answering the presence of related target molecules. Field effet transistor was fabricated using graphene as a channel and monitored by the source-drain current and back-gate voltage curves in the measurement. The transport property changed compared to that of the FET made by intrinsic graphene, that is, the Dirac point position moved from positive Vg to negative Vg, indicating the transition of graphene from p-type to n-type after annealing in TNT, and GFET sensor show good sensitivity and selectivity response.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high-precision seawater refractive index measurements. A seawater refractive index measurement system based on position-sensitive detectors is an effective means to achieve high-precision measurement of seawater refractive index. However, in the actual seawater refractive index measurement process, the impact of the measurement error caused by the jitter signal obtained from the measurement on the measurement results cannot be ignored. In this paper, we theoretically analyse the causes of the long jitter signals during seawater refractive index measurement and quantify the influencing factors. Through the analysis, it can be seen that the angle between the two windows in the refractive index measurement area of seawater causes a great error on the measurement results, so the angle between the two windows should be controlled within 2.06° in order to effectively reduce the measurement error. At the same time, the factors affecting the measurement accuracy of the position-sensitive detector are analysed, and the factors leading to the reduction of the measurement accuracy of the position-sensitive detector are mainly the background light, the size of the photosensitive surface, and the change of the temperature of the working environment. For the above factors, we add a narrow-band filter with a bandwidth of 0.9nm in front of the photosensitive surface of the position-sensitive detector during the construction of the measurement system, so as to filter out stray light other than the signal light source. On the premise of ensuring the measuring range of the refractive index of seawater, a position-sensitive detector with a photosensitive surface size of 4 mm×4 mm was selected. In order to reduce the temperature variation of the working environment of the position-sensitive detector, the measurement system was partitioned. In order to validate the testing error range of the optimised test system, standard seawater samples under the same conditions were measured. It can be seen that the jitter signal of the measurement system has been reduced from 0.0022mm before the optimisation to 0.0011mm after the optimisation, and the deviation of the refractive index has been reduced by 1.09×10−8RIU. The experimental results show that the refractive index of seawater has been effectively reduced by adjusting the optical path and the structure of the seawater refractive index measurement system.

The effect of wave forces on the structural safety of fixed oscillating water-column (OWC) devices is critical. In this study, a three-dimensional numerical model of an oscillating water column (OWC) device is constructed using the computational fluid dynamics software OpenFOAM. Subsequently, the hydrodynamic performance of the numerical model is comprehensively validated. Finally, the hydrodynamic performance data are analyzed in detail to obtain meaningful conclusions. The results indicate that the horizontal wave force on the OWC device is approximately 6.6 to 7.9 times greater than the vertical wave force, whereas the lateral wave force is relatively small. Both the horizontal and vertical wave forces decrease as the relative water depth increases under a constant wave period and height. The horizontal wave force increases linearly with the wave height, whereas the vertical wave force increases with the square of the wave height. In addition, the highest dynamic water pressure is observed at the interface between the water surface and device, both within and outside the front wall of the gas chamber. The dynamic water pressure at different locations on the front chamber increases and subsequently decreases as the wave frequency increases.

Wave steepness is presented as an extension and a valuable add-on to the conventional set of sea state parameters retrieved from satellite altimetry data. Following physical model based on recent advances of weak turbulence theory wave steepness is estimated from directly measured spatial gradient of wave height. In this way the method works with altimetry trajectories rather than with point-wise data. Moreover, in contrast to widely used parametric models this approach provides us with instantaneous values of wave steepness and period. Relevance of single-track estimates of wave steepness (period) is shown for wave climate studies and confirmed by a simple probabilistic model. The approach is verified via comparison against buoy and satellite data including crossover points for standard 1 second data of Ku-band altimeters. High quality of the physical model and robustness of the parametric ones are examined in terms of global wave statistics. Prospects and relevance of both approaches in the ocean wave climate studies are discussed.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Two distinct measures of information, connected respectively to the amplitude and phase of the wave function of a particle, are proposed. There are relations between the time derivatives of these two measures and their gradients on the configuration space, which are equivalent to the wave equation. The information related to the amplitude measures the strength of the potential coupling of the particle (which is itself aspatial) with each volume of its configuration space, i.e. its tendency to participate in an interaction localized in a region of ordinary physical space corresponding to that volume. The information connected to the phase is that required to obtain the time evolution of the particle as a persistent entity starting from a random succession of bits. It can be considered as the information provided by conservation principles. The meaning of the so-called "quantum potential" in this context is briefly discussed.

Chaotic theory is commonly being researched for application in image encryption scheme (IES). In this paper, a novel two-dimensional cross hyperchaotic Sine-modulation-Logistic map (2D-CHSLM) based on the famous Sine and Logistic maps. The hyperchaotic behaviors of 2D-CHSLM is testified with the help of their bifurcation diagrams, trajectory plots, Lyapunov exponents, sample entropy, C0 complexity, permutation entropy and 0-1 test. A new bit-level IES with traditional encryption structure is proposed utilizing 2D-CHSLM. The 2D-CHSLM-IES performs a 2D-CHSLM-based bit-level confusion using zig-zag transform and a 2D-CHSLM-based cross coupled diffusion operations for generating a highly secure cipher-image. Then the simulations and security analyses are further carried out with the help of key space, key sensitivity, histogram, correlation, information entropy, differential attack, noise and data loss attacks, prove that the security of the proposed 2D-CHSLM-IES

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

This review explores the potential implementation of lithium tetraborate (Li2B4O7) as a scintillator medium for neutron detection applications. Several characteristics required for the neutron detection process suggest that Li2B4O7 could be a suitable material for scintillation-based neutron detection systems. The inherently large neutron capture cross-section due to 10B and 6Li isotopes, and the ease with which Li2B4O7 can be enriched with these isotopes, combined with the facile inclusion of rare-earth dopants are all expected to improve luminescent properties as well as neutron detection efficiency of Li2B4O7. The electronic structure of doped and undoped Li2B4O7 are explored using photoemission and inverse photoemission spectroscopies, optical measurements, and theoretical computational studies such as density functional theory. The scintillation properties are further enhanced because of the wide bandgap, and transparency towards the photons that are emitted following neutron capture.

We describe a family of paraxial and quasi-monochromatic optical wave packets with finite energy and smoothly shaped amplitude in space and time that develops a singularity in the intensity when spatiotemporally focused by imparting a converging spherical wave front and a negative temporal chirp. This singular behavior upon ideal focusing is manifested in actual focusing with finite apertures and in media with high-order dispersion in an "exploding" behavior featuring indefinitely increasing concentration of the energy when opening the aperture radius, thus exercising a continuous control on the focal intensity and spatial and temporal resolution. These wave packets offer a new way of focusing that outperforms what can be achieved with standard Gaussian wave packets in terms of focal intensity and resolution, and new possibilities in applications where energy concentration and its control are crucial.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

Continuous-wave photocathode guns are capable of delivering electron beams with high repetition rates and high average currents. However, they are limited by relatively low accelerating gradients and cathode fields. This limitation leads to a larger beam size at the gun exit due to space charge forces, making the beam more sensitive to optical aberrations and posing challenges for low-emittance electron beam transmission. This paper focuses on the aberrations induced by multipole fields. We analyze the effects of quadrupole, sextupole, and higher-order fields on beam profile and transverse emittance and propose a beam-based method for the rapid characterization and correction of these multipole fields. Furthermore, we present an experimental study conducted on the DC-SRF-II photocathode gun equipped with dedicated correctors. Both simulation and experimental results demonstrate that our approach effectively mitigates beam aberrations caused by multipole fields, resulting in improved beam symmetry and reduced emittance.

By using Modified simple equation method, we study the Cahn Allen equation which arises in many scientific applications such as mathematical biology, quantum mechanics and plasma physics. As a result, the existence of solitary wave solutions of the Cahn Allen equation is obtained. Exact explicit solutions interms of hyperbolic solutions of the associated Cahn Allen equation are characterized with some free parameters. Finally, the variety of structure and graphical representation make the dynamics of the equations visible and provides the mathematical foundation in mathematical biology, quantum mechanics and plasma physics.

Recent advancements in semiconductor photonic and electronic devices such as Uni-travelling-carrier photodiodes (UTC-PDs), have played a significant role in the development of Terahertz communication technology. However, a major challenge that still persists is the limited output power from a single UTC-PD required for practical transmission distances. To enhance the output power, we propose and demonstrate a novel Terahertz wave power combining technique using a photomixer device that comprises of two arrayed UTC-PDs monolithically integrated with a microstrip line-based 2 × 1 Wilkinson power combiner and a rectangular patch antenna on a Silicon Carbide (SiC) substrate at 300 GHz. At photocurrents of 8 mA and 10 mA from the two UTC-PDs, the device experimentally exhibited a 7.3 dB increase in power relative to the power obtained with 8 mA UTC-PD and a 4.4 dB increase in power relative to the power obtained with 10 mA UTC-PD, when both UTC-PDs were irradiated. This implies that power can be enhanced by a factor of N2 if the photocurrent is multiplied by a factor of N. This technology presents a holistic and cutting edge platform for further power multiplication by further increasing the number of arrayed UTC-PDs.

We review time expansion wave theory and refine our model showing it to accurately match observed cosmological luminosity data. The theory augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension that we observe as the expansion of the universe. This leads us to explain mass creation, the speed of light limit, gravity, black holes without singularities and other macroscopic effects. Our model leads to an expansion velocity of 6.87 0.36 × 106 ms-1, which results in a Hubble expansion rate constant of 71.3 3.7 km/s/Mpc. Because of the finite window of time in which we exist, an extra a degree of freedom is available leading to interesting interpretations at the subatomic level. At this size range, then a spin is allowed within the time dimension explaining why wave particle duality occurs and explains the electromagnetic force and other quantum mechanical properties. It provides a solution to the double slit conundrum and can explain how quantum entangled partners can behave in a quantum way and pass seemingly time-defying information. The potential quantitative origin of the fine structure constant which governs the size of the electromagnetic force is also strongly indicated by this theory.

Planetary waves in the mesosphere are studied using observational data and models to establish their origin, as there are indications of their generation independently of waves in the stratosphere. The quantitative relationships between zonal wave numbers m = 1 (wave 1) and m = 2 (wave 2) were studied with a focus on the mid-latitude mesosphere at 50N latitude. Aura Microwave Limb Sounder measurements were used to estimate wave amplitudes in geopotential height during the 2020–2021 winter major sudden stratospheric warming. The moving correlation between the wave amplitudes shows that, in comparison with the anticorrelation in the stratosphere, wave 2 positively correlates with wave 1 and propagates ahead of it in the mesosphere. A positive correlation r = 0.5–0.6, statistically significant at the 95% confidence level, is observed at 1–5-day time lag and in the 75–91 km altitude range, which is the upper mesosphere–mesopause region. Wavelet analysis shows a clear 8-day period in waves 1 and 2 in the mesosphere at 0.01 hPa (80 km), while in the stratosphere–lower mesosphere the period is twice as long at 16-days; this is statistically significant only in wave 2. Possible sources of mesospheric planetary waves are discussed.

An expansion method based on time fractional Sine-Gordon equation is implemented to construct some real and complex valued exact solutions to the Korteweg-de Vries and modified Korteweg-de Vries equation in time fractional forms. Compatible fractional traveling wave transform plays a key role to be able to apply homogeneous balance technique to set the predicted solution. The relation between trigonometric and hyperbolic functions based on fractional Sine-Gordon equation allows to form the exact solutions with multiplication of powers of hyperbolic functions.

The Sine-Gordon expansion method is implemented to construct exact solutions some conformable time fractional equations in Regularized Long Wave(RLW)-class. Compatible wave transform reduces the governing equation to classical ordinary differential equation. The homogeneous balance procedure gives the order of the predicted polynomial-type solution that is inspired from well-known Sine-Gordon equation. The substitution of this solution follows the previous step. Equating the coefficients of the powers of predicted solution leads a system of algebraic equations. The solution of resultant system for coefficients gives the necessary relations among the parameters and the coefficients to be able construct the solutions. Some solutions are simulated for some particular choices of parameters.

The main goal of the paper is to compare the effects of the wave spectrum, computed using the Discrete Interaction Approximation (DIA) and the Webb–Resio–Tracy (WRT) methods, on statistical wave properties such as skewness and kurtosis. The statistical properties are obtained by integrating the three-dimensional free-surface Euler equations with a high-order spectral method combined with a phenomenological filter to account for the energy dissipation due to breaking waves. In addition, we investigate the minimum spatial domain size required to obtain meaningful statistical wave properties. The numerical simulations are performed over a physical domain of size 4.13 km × 4.13 km. The results indicate that statistical properties must be computed over an area of at least 4 km2. The results also suggest that selecting a more computationally expensive WRT method does not affect the statistical values to a great extent. The most noticeable effect is due to the energy dissipation filter that is applied. It is concluded that selecting the WRT or the DIA algorithm for computing the wave spectrum needed for the numerical simulations does not lead to major differences in the statistical wave properties. However, more accurate energy dissipation mechanisms due to wave breaking are needed.

In the framework of maritime surveillance, vessel detection techniques based on spaceborne Synthetic Aperture Radar (SAR) images have promoted extensive applications for the effective understanding of unlawful activities at sea. The paper deal with this topic presenting a novel approach exploiting a cascade application of a pre-screening, and discrimination phase. The latter leverage the SAR spectrum by means of sub-looks analysis. For the first time, the method has been validated with experiments on multi-frequency (C-, X-, and L-band) SAR images. For a future syngergic exploitation of more SAR missions, the developed dataset, composed of Sentinel-1, SAOCOM and COSMO-SkyMed images, is comprehensive of multiple images gathered over the same area with short time lag (below 15 minutes). Finally, the diversified processing chains and the results for each mission product and scenarios are discussed. Being the first dataset of SLC (Single Look Complex) SAR multi-frequency data, the present work intends to encourage additional research in this promising field of research.

Loop detectors are probably the widest-used technology for traffic state estimation. Previous research has shown that loop detector positions within the link significantly affect the estimation of the macroscopic fundamental diagram (MFD) of a given network. This paper examines the biases produced by the positioning of loop detectors on the MFD, using both analytical and simulation methods, as well as empirical data from UTD-19. We confirm earlier results that a uniform distribution of loop detector positions reduces the bias. For non-uniform distribution, we found that: (i) the subsets of the MFD by the loop detector position help estimate whether the loop detector MFD will have a bias; (ii) if the detectors in the network are positioned more downstream with a larger variation, the loop detector MFD is more likely to have a discrepancy in position subsets of the MFD; (iii) a lower ratio of link length to green signal time elevates the MFD bias as well. This research opens the possibility for the bias of MFD induced by the loop detector data to be corrected by only using itself.

The vast rise in the number of Internet-connected devices necessitates a more accessible spectrum. As a result, Cognitive Radio was already proposed as a solution to the problem of restricted spectrum resources by utilizing available spectrum which is assigned to primary users. This method allows the secondary user to utilize the spectrum whenever the primary user is not using it, and it does so without intruding with the primary user. Whenever the secondary user detects the spectrum, it faced some issues, such as complexity in sensing leading to a lack of noise value, and the primary user is hidden to all secondary users. In order to tackle these challenges, an adaptive threshold matched filter detector and a cooperative matched filter detector are utilized in this paper to detect the spectrum. The probability of detection (Pd), probability of miss detection (Pm), and probability of false alarm (Pf) are the metrics used to assess sensing accuracy. To simulate suggested detectors, the MATLAB R2020a software was utilized. In comparison to earlier studies, the simulation conclusions reveal that the detection process starts with lower SNR values.

Fluorescence microscopy provides an unparalleled tool for imaging biological samples. However, producing high-quality volumetric images quickly and without excessive complexity remains a challenge. Here, we demonstrate a simple multi-camera structured illumination microscope (SIM) capable of simultaneously imaging multiple focal planes, allowing for the capture of 3D fluorescent images without any axial movement of the sample. This simple setup allows for the acquisition of many different 3D imaging modes, including 3D time lapses, high-axial-resolution 3D images, and large 3D mosaics.

Significant Wave Height(SWH) is a crucial parameter in oceanographic research, essential for understanding various marine and atmospheric processes. Traditional methods for obtaining SWH, such as ship-based and buoy measurements, face limitations like limited spatial coverage and high operational costs. With the advancement of Global Navigation Satellite Systems reflectometry(GNSS-R) technology, a new method for retrieving SWH has emerged, demonstrating promising results. This study utilizes Radio occultation sounder(GNOS) data from the FY-3E satellite and incorporates the latest Vision Transformer(ViT) technology to investigate GNSS-R-based SWH retrieval. We designed and evaluated various deep learning models, including ANN-Wave, CNN-Wave, Hybrid-Wave, Trans-Wave, and ViT-Wave. Through comparative training using ERA5 data, the ViT-Wave model was identified as the optimal retrieval model. The ViT-Wave model achieved an Root Mean Square Error(RMSE) accuracy of 0.4052 meters and Mean Absolute Error(MAE) accuracy of 0.2700 meters, significantly outperforming both traditional methods and newer deep learning approaches utilizing Cyclone Global Navigation Satellite Systems(CYGNSS) data. These results underscore the potential of integrating GNSS-R technology with advanced deep learning models to enhance SWH retrieval accuracy and reliability in oceanographic research.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Using a scaling symmetry, it is shown how to compute polynomial conservation laws, generalized symmetries, recursion operators, Lax pairs, and bilinear forms of polynomial nonlinear partial differential equations thereby establishing their complete integrability. The Gardner equation is chosen as the key example for it comprises both the Korteweg-de Vries and modified Korteweg de Vries (mKdV) equations. The Gardner and Miura transformations which connect these equations are also computed using the concept of scaling homogeneity. Exact solitary wave solutions and solitons of the Gardner equation are derived using Hirota’s method and other direct methods. The nature of these solutions depends on the sign of the cubic term in the Gardner equation and the underlying mKdV equation. It is shown that flat (table-top) waves of large amplitude only occur when the sign of the cubic nonlinearity is negative (defocusing case) whereas the focusing Gardner equation has the standard elastically colliding solitons. The paper’s aim is to provide a review of integrability properties and solutions of the Gardner equation and illustrate the applicability of the scaling symmetry approach. The methods and algorithms used in this paper have been implemented in Mathematica but can be adapted for major computer algebra systems.

A well known technique to enhance the signal to noise ratio (SNR) of repetitive signals is to average them. The coherent parts of the signal add up constructively while the incoherent parts are averaged out. The prerequisite is that the signals are acquired under conditions of high repeatability, i.e.\ the signals must be sufficiently similar. In the present technical note we describe an efficient method for maintaining signal similarity by ensuring spatial and temporal proximity of laser waveform signals obtained by a sensor operated from an airborne platform. The method makes use of a few auxiliary parameters such as laser pulse repetition rate, mirror rotation rate, platform altitude, and flight speed. The method can be extended to be operated in real time.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

Background: Injury of the spinal cord causes motor and sensory dysfunction, and pathological reflexes, leading to paraplegia or tetraplegia. The sequelae of traumatic spinal cord injury (SCI) is a significant burden and impact on healthcare systems. Despite constant progress in medicine, traumatic SCI still remains irreversible. Till now, no satisfying treatment that can enable neuronal regeneration and recovery of function at the damaged level has been found. Hundreds of experiments have been conducted on various possibilities of influencing spinal regeneration, some of them have yielded promising results, but unfortunately, the successes obtained in experimental animals have not translated into humans. Methods: This narrative review article presents the application of Extracorporeal Shock Wave Therapy (eSWT) in Spinal Cord Injury. The article has been divided into parts: 1. Use of extracorporeal Shock Wave Therapy for regeneration of the spinal cord after traumatic Spinal Cord Injury. 2. Application of extracorporeal Shock Wave Therapy in spasticity after Spinal Cord Injury. In both cases, the hypotheses of possible mechanisms of action will be described. Results and conclusions: A small number of clinical trials have demonstrated the potential of eSWT to influence the regeneration of the spine, as an innovative, safe, and cost-effective treatment option for patients with SCI. Some reports have shown that eSWT can improve spasticity, walking ability, urological function, quality of life, and independence in daily life.

In this paper, we study nonlocal problems for a fractional diffusion equation and a degenerate hyperbolic equation with singular coefficients in the lower terms. The uniqueness of the solution to the problem is proved by the method of energy integrals. The existence of a solution is equivalently reduced to the question of the solvability of Volterra integral equations of the second kind and a fractional differential equation. For a particular solution of the proposed problem, its visualization is carried out for various values of the order of the fractional derivative. It is shown that the order of the derivative affects the intensity of the diffusion process (subdiffusion), as well as the shape of the wave front.

In the framework of the H2020 CLEANDEM project a small robotic vehicle was equipped with a series of different sensors, developed for the preliminary inspection of areas possibly contaminated by radiation. Such unmanned inspection allows to identify dangerous locations prior to the possible start of human operations. One of the developed devices, named MiniRadMeter, is a compact, low-cost sensor to perform gamma and neutron radiation field mapping of the environment. The MiniRadMeter was successfully tested in a simulated field mission with four "hidden" radioactive sources and a neutron generator. In this work we describe the test procedure and the results, also supported by the outcome of dedicated Monte Carlo simulations.

Abstract: Development of the fast neutron radiography with higher penetration capability in Non-Destructive Testing (NDT) techniques is rapidly. The detection efficiency and the imaging spatial resolution are the main problem of the radiography detector for many fast neutron imaging systems. In this paper, a detector composed of pixelated EJ200 scintillator array，an 16 × 16 silicon-photomultipliers (SiPM) array, and a capacitive multiplexing network readout electronics is designed. Using Monte-Carlo simulations，the main parameters of the detector was optimization. Then the detector prototype was fabricated and tested at a 14 MeV D-T neutron source. The preliminary test results showed that the prototype has spatial resolution of 1.26 mm. Using pixelated scintillator structure，the conflict between spatial resolution and detect efficiency could improved. Moreover, SiPMs offer a flexibility for the expansion of application field of the imaging system due to their excellent photon detection performance, relatively low price and joint possibility for large area.

Compton cameras detect scattered gamma rays and estimate the distribution of gamma-ray sources. Nonetheless, crafting a camera tailored to a specific application presents formidable challenges, often necessitating the implementation of diverse image reconstruction techniques. Delving into the factors influencing these cameras can pave the way for design optimization and performance enhancement. This study introduces an inventive detector design for Compton imaging systems, building upon the achievements of prior designs. The proposed system contains eight scatterer detectors and a semiconductor absorber detector, spaced at 1 mm and 30 mm intervals, respectively. The source-to-first-scatterer-detector distance is 5 mm, with scatterer and absorber detector plates measuring 70× 70× 2.125 mm³ and 70× 70× 10 mm³, respectively. Geant4 simulation toolkit models the Compton imaging system, and an analytical method reconstructs Compton camera images. Unlike more straightforward techniques, the analytical method directly reconstructs Compton camera images by solving the equation relating to the reflected image data. This approach is implemented in the C++ programming language. The study's findings reveal that the analytical method discerns optimal conditions and parameters that significantly influence efficiency, yielding a full width at half maximum (FWHM) of 3.7 mm with an angular uncertainty of approximately 2.7 degrees at an energy level of 0.662 MeV. Compared to another experimental design employing the analytical image reconstruction approach, the FWHM value decreased by 0.7 mm. This study presents an innovative detector design and an analytical reconstruction method for Compton imaging systems, showcasing improved efficiency and accuracy.

We report a novel dual-band barrier infrared detector (DBIRD) design using type-II superlattices (T2SLs). The DBIRD structure consists of back-to-back barrier diodes: a "blue channel" (BC) diode which has an nBp architecture, an n-type layer of larger bandgap for absorbing blue band infrared/barrier/p-type layer, and a "red channel" (RC) diode which has an pBn architecture, a p-type layer of smaller bandgap for absorbing red band infrared/barrier/n-type layer. Each has a unipolar barrier using a T2SL lattice matched to a GaSb substrate to impede the flow of majority carriers from the absorbing layer. Each channel in the DBIRD can be independently accessed with a low bias voltage, as is preferable for high-speed thermal imaging. Device modeling of DBIRDs and simulation results of the current-voltage characteristics under dark and illuminated conditions are also presented. They predict that dual-band operation of the DBIRD will produce low dark currents and 27-33% quantum efficiencies for the in-band photons in the BC with λc=5.58 μm, and a nearly-constant 33% in the RC with λc=8.05 μm. The spectral quantum efficiency of the BC for 500 K blackbody radiation is approximately 20% over the range of λ=3 − 4.2 μm, while that of the RC has a peak of 42% at 5.7 μm. The DBIRD may provide improved high-speed dual-band imaging in comparison with NBn dual-band detectors.

Muography is an expanding technique for the investigation of the internal structure of targets of interest in geophysics. The flux of high penetrating muons produced by primary cosmic rays is attenuated by traversing kilometer size objects like X-ray flux is attenuated through the human body. This gives the possibility to study the internal structure of volcanoes or underground cavities, e.g., starting from the measure of the muon flux transmission through the target. Many groups of researchers working with this technique have to face with high background level that afflicts the reconstruction of muon tracks near the horizontal direction. An important source of background is the scattering of particles near the detector that produces a wrong reconstruction of the incoming direction. An innovative technique based on Cherenkov radiation was investigated by means of Monte Carlo simulations developed in Geant4 toolkit and MATLAB. The results reported in this paper show that the presented technique is able to correctly distinguish the incoming direction of particles with an efficiency higher than 98%. This new kind of detector could represent an alternative for high resolution charged particle tracking also for other applications.

Malignant growth is the most widely recognized repulsive infections winning around the world, and the patients with disease are saved just when the malignant growth is distinguished at the beginning phase. Each kind of disease is interesting, with its own arrangement of development properties and hereditary changes. This paper presents the lung knob division and disease characterization by proposing an enhancement calculation. The general technique of the created approach includes four stages, such as pre-processing, division, highlight extraction, and the order. From the outset, the CT picture of the lung is taken care of to the division. When the division is done, the highlights are extricated through morphological and measurable and surface highlights like LOOP and LGP. At long last, the extricated highlights are given to the order step. Here, the characterization is done dependent on the Deep Belief Network (DBN) which is prepared by utilizing the proposed Chicken-Sine Cosine Algorithm (CSCA) which distinguish the lung tumor, giving two classes in particular, knob or non-knob. The presentation assessment of lung knob division and malignant growth grouping dependent on CSCA is figured utilizing three measurements to be specific, precision, affectability, and the explicitness.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

An HFMD outbreak spread over the city of Hải Phòng from Summer 2011 to Autumn 2012. This epidemic was chosen because it was the very first HFMD epidemic in North Vietnam, eliminating thus interferences with previous outbreaks. This epidemic displayed 3 separate waves. A complete dataset was collected for more than 9500 patients during this period, which enabled us to analyze this epidemic at different scales. Access to the healthcare system was crucial during this period, with a reorganization of the system in February-March 2012. An analysis at commune level enables us to track the epidemic along certain communication routes. The three-waves structure reveals a wide disparity at district level. We develop a mathematical model showing high accuracy at the adjustment of data for both the total number of cases and for the number of cases per week. As a consequence, the model was able to accurately determine the dates of beginning and end of each wave and to show that they overlapped. Using mathematical functions associated with this model, it was possible to calculate the probability for a patient to belong to a specific wave.

New exact solutions to conformable time fractional EW and modified EW equations are constructed by using Sine-Gordon expansion approach. The fractional traveling wave transform and homogeneous balance have significant roles in the solution procedure. The predicted solution is of the form of some finite series of multiplication of powers of cos and sin functions. The relation among trigonometric and hyperbolic functions in sense of Sine-Gordon expansion gives opportunity to construct the solutions in terms of hyperbolic functions.

Anomaly occurrences in hydraulic machinery may lead to massive systems shut down, jeopardizing the safety of the machinery and its surrounding human operator(s) and environment, and the severe economic implications succeeding the faults and their associated damage. Hydraulics are mostly placed in ruthless environments, where they are consistently vulnerable to many faults. Hence, not only the machines and their components are prone to anomalies, but also the sensors attached to them, which monitor and report their health and behavioral changes. In this work, a comprehensive applicational analysis of anomalies in hydraulic systems extracted from a hydraulic test rig is thoroughly achieved. Firstly, we provided a combination of a new architecture of LSTM autoencoders and supervised machine and deep learning methodologies to perform two separate stages of fault detection and diagnosis. The two phases are condensed by: the detection phase using the LSTM autoencoder. Followed by the fault diagnosis phase represented by the classification schema. The previously mentioned framework is applied to both component and sensor faults in hydraulic systems, deployed in the form of two in-depth applicational experiments. Moreover, a thorough literature review of the past decade related work for the two stages separately is successfully conducted in this paper.

Any Geiger counter can be used as an effective cosmic ray detector on its own. In fact, it is known that even in the absence of a radioactive source, the instrument detects what is known as background radiation, which consists of various types of ionizing particles present in the environment. Remarkably, it is estimated that up to 15% of this background radiation is attributable to cosmic rays, high-energy particles originating from outer space. The remaining radiation detected by the Geiger counter originates from terrestrial sources, such as natural radioactivity in the ground and in the air. The main goal of this project is to build a muon detector for scientific and educational purposes using two commercial DIY Geiger counter kits and just a few additional components. To identify cosmic radiation from terrestrial radiation and improve the accuracy of cosmic ray measurements, the use of a coincident circuit is essential. This coincident circuit was introduced in cosmic ray physics by Walther Bothe and Bruno Rossi in the early 1930s and allows for the detection of a subatomic particle passing through two or more sensors, thereby reducing false positives and enhancing the reliability of cosmic ray detection.The following idea is an alternative to our AMD5 detectors, instruments that we have been using for years to teach and perform scientific experiments in the cosmic ray field under the umbrella of the ADA project (2023 Particles, Arcani et al.). The resulting device offers a reliable and cheap solution for the same goal, making it a valuable tool for both educational purposes and even scientific surveys.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

We attempted to apply the optoelectronic sensor entitled 'OPT101' in intensive care unit clinics, based on its optoelectronic response characteristics in near-infrared wavelength range and near-infrared spectroscopy principle. The successful novel applications in our lab include early-diagnosis and therapeutic effect tracking of thrombus, noninvasive monitoring of patients' shock severity, and fatigue evaluation. This study also expects further improvements of the detector in noninvasive clinical applications.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

The scattering eigenstates of any Hamiltonian of electrons, coupled through a two-body force and moving on a one-dimensional lattice, are shown to be Bethe's wave-functions. The energy of the groundstate is compared with values, obtained previously for the Hubbard Hamiltonian by means of Bethe's wave-function and within the framework of the correlated Fermi gas. The same analysis is applied to electrons, interacting on neighbouring sites. The significance of those various groundstates is assessed with help of thermodynamics.

The wave packet consisting of two harmonic plane waves with the same frequencies, but with different wave vectors is considered. The dispersion relation of a packet is structurally similar to the dispersion relation of a relativistic particle with a nonzero rest mass. The possibility of controlling the group velocity of a quasi-monochromatic wave packet by varying the angle between the wave vectors of its constituent waves is discussed.

The Wave Mode (WM) is a unique imaging mode of spaceborne synthetic aperture radar (SAR), which is dedicatedly designed for global ocean surface wave observations. Since it was firstly achieved in the ERS-1/SAR satellite starting from 1991, the WM data over global oceans have been continuously acquired by the ESA’s SAR instruments onboard the satellites of ERS-2 (1997 – 2011), ENVISAT (2002 – 2012), Sentinel-1A(2014--)/1B(2016--) and the Chinese GaoFen-3 SAR (2016--), for nearly 30 years. Therefore, spaceborne SAR WM data have been a ‘big data’, which however, has not been widely exploited for global ocean wave measurements. In this study, we demonstrate its application on global ocean wave measurements based on the ten-year Advanced SAR (ASAR) WM data.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high precision seawater refractive index measurement. In this paper, we propose a method for measuring the refractive index of seawater based on a Position Sensitive Detector (PSD). Theoretical model is established to depict the correlation between laser spot displacement and refractive index change, utilizing a combination of position sensitive detector and laser beam deflection principle. Based on this optical measurement method, a seawater refractive index measurement system was established. To effectively enhance the sensitivity of refractive index detection, a focusing lens was incorporated into the optical path of the measuring system, and simulations were conducted to investigate the impact of focal length on refractive index sensitivity. The calibration experiment of the measuring system was performed based on the relationship between refractive index of seawater and underwater pressure (depth). By measuring laser spot displacement at different depths, changes in displacement with respect to both refractive index and depth were determined. Experimental results demonstrate that the system exhibits a sensitivity of 9.9277×10−9RIU (refractive index unit), the refractive index deviation due to stability is calculated as ±7.545×10−9RIU. Thereby the feasibility of highly sensitive measurement of seawater refractive index is verified.

The shortwave infrared Ge-Si photodetector will become the core device of the LiDAR optical receiver. In order to meet the urgent demand for photodetectors in the LiDAR field, we have designed and produced a 32×32 pixel Ge-Si photodetector array proposed and developed to meet the performance requirements of the detector array. A dark current detection system for fast scanning and detecting large-scale Ge-Si detector arrays is proposed and developed to achieve rapid detection of dark current in each pixel of the detector. The system was used to validate the main performance indicators of the detector array we designed, achieving rapid discrimination of array performance and rapid localization of damaged pixels. The scanning test results show that the average dark current of the detector array chip we designed is at the nano ampere level, and the proportion of bad points is less than 1%. The consistency of the array chip is high, which can meet the requirements of light detection at the receiving end of the LiDAR. This work laid the foundation for our subsequent development of a LiDAR prototype system.

In this work, PMMA(Poly methyl methacrylate) microfluidic system was used as a micro-reactor for urea hydrolysis by urease enzyme with use conductivity principle and utilize sound level meter(SLM) App in smartphone as a novel detector by considering the peak height in the App as an indicate for urea concentration. the advantage of use small volume and how the reaction carried on in the microfluidic system with simple and low cost are discussed, and the results were analyzed and statically determine. The linearity, detection limit (3×noise )and Correlation Coefficient, 62.5-500 ppm, 31.25 ppm and 0.992 respectively also, recovery studied were between(98.5-100.13%).

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

Introduction: The COVID-19 pandemic challenged people with spinal cord injury (SCI) regarding a variety of mental and physical issues. New challenges may arise as the effects of the pandemic continue. The objective of the present study was to explore the social participation of Canadians with SCI during the second wave of COVID-19. Methods: Participants with SCI from two Canadian provinces (Quebec and British Columbia) were interviewed. Results: Eighteen participants completed interviews. Facilitators of social participation remain similar since the first wave of COVID-19, such as the use of technology, help received by relatives and the use of delivery services to obtain groceries and other essentials. Obstacles to mobility due to winter conditions and lack of considerations related to COVID-19 public health measures specific to wheelchair users were also discussed by participants. Conclusions: People with SCI perceived participation restrictions, little changes in life habits, and uncertainty about the future during the second wave of COVID-19. The unique living conditions of people with SCI, ability to adapt life habits, and the lived experiences of people with SCI may have contributed to an overall resilience during the pandemic. Adaptive families, social contacts and technology made a difference during the pandemic.

Hydrogenated amorphous silicon (a-Si:H) can be produced by plasma-enhanced chemical vapour deposition (PECVD) of SiH4 (Silane) mixed with Hydrogen. The resulting material shows outstanding radiation resistance properties and can be deposited on a wide variety of different substrates. These devices have been used to detect many different kinds of radiation namely: MIPs, x-rays, neutrons and ions as well as low energy protons and alphas. However, MIP detection using planar diodes has always been difficult due to the unsatisfactory S/N ratio arising from a combination of high leakage current, high capacitance and a limited charge collection efficiency (50% at best for a 30 µm planar diode). To overcome these limitations the 3D-SiAm collaboration proposes to use a 3D detector geometry. The use of vertical electrodes allows for a small collection distance to be maintained while conserving a large detector thickness for charge generation. The depletion voltage in this configuration can be kept below 400 V with consequent reduction in the leakage current. In this paper, following a detailed description of the fabrication process, the results of the tests performed on the planar p-i-n structures made with ion implantation of the dopants and with carrier selective contacts will be illustrated.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

In this short note we present a technique using which one attributes frequency and wavevector to (almost) arbitrary scalar fields. Our proposed definition is then applied to the classical wave equation to yield a novel nonlinear PDE.

Time is a component quantity of various measurements and is also used on its own to sequence events, to compare the duration of events or the intervals between them, and to quantify rates of change of quantities in material reality or in the conscious experience [1]. The measuring equipment well might happen to be a clock. By making a presupposition that clock is Time, it is perceived experimentally that “Time exhibits wave-like properties”

Wave overtopping, i.e., excess of water over the crest of a coastal protection infrastructure due to wave run-up, of a smooth slope can be reduced by introducing slope roughness. A stepped revetment ideally constitutes a slope with uniform roughness. Apart from reducing overtopping, a stepped revetment provides safer access to a beach compared to conventional rubble. In recent years, research studies on stepped revetments have provided valuable findings regarding the performance and design optimization of stepped revetments as a typical mean of coastal protection. A stepped revetment can reduce overtopping volumes of breaking waves up to compared to a smooth slope. The effectiveness of the overtopping reduction decreases with increasing Iribarren number. However, up to date a unique approach applicable for a wide range of boundary conditions is still missing. The present paper critically reviews previous findings, gathers and analyzes data from previous studies and proposes a new formula for robust prediction of overtopping of stepped revetments. By means of this approach a critical assessment based on beforehand disclosed parameter ranges between a smooth slope on the one hand and a plain vertical wall on the other are contrasted. By analysis of a new data set compounded from different original studies a novel empirical formulation is derived to predict the roughness reduction coefficient of a stepped revetment for breaking and non-breaking waves. This coefficient is developed and adjusted for a direct incorporation into the present design guidelines. Underlying uncertainties are clearly addressed and quantified. Scale effects are highlighted.

Detecting rotational objects in remote sensing imagery is a significant challenge. These images typically encompass a broad field of view, featuring diverse and intricate backgrounds, with ground objects of various sizes densely scattered. As a result, identifying objects of interest within these images is a daunting task. While the integration of Convolutional Neural Networks (CNN) and Transformer networks leads to some advancements in rotational object detection, there is still room for improvement, particularly in enhancing the extraction and utilization of information related to smaller objects. To address this, our paper presents a multi-scale feature fusion module and a global feature context aggregation module. Initially, we fuse original, shallow, and deep features to reduce the loss of shallow feature information, thereby improving the detection performance of small objects in complex backgrounds. Subsequently, we compute the correlation of contextual information within feature maps to extract valuable insights. We name the newly proposed model the "Multiscale Feature Context Aggregation Module" (MFCA). We evaluate our proposed methodology on three challenging remote sensing datasets: DIOR-R, HRSC, and MAR20. Comprehensive experimental results show that our approach surpasses baseline models by 2.07\% mAP, 1.02\% mAP, and 1.98\% mAP on the DIOR-R, HRSC2016, and MAR20 datasets, respectively.

Automatic target detection of remote sensing images (RSI) plays an important role in military reconnaissance, disaster monitoring, and target rescue. The core task of remote sensing target detection is to judge the target categories and complete precise location. However, the existing target detection algorithms have limited accuracy and weak generalization capability for remote sensing images with complex backgrounds. To achieve accurate detection of different categories targets in remote sensing images, this study presents a novel feature enhancement single shot multibox detector (FESSD) algorithm for remote sensing target detection. The FESSD introduces feature enhancement module and attention mechanism into the convolution neural networks (CNN) model, which can effectively enhance the feature extraction ability and nonlinear relationship between different convolution features. Specifically, the feature enhancement module is used to extract the multi-scale feature information, and enhance the model nonlinear learning ability; the self-learning attention mechanism (SAM) is used to expand the convolution kernel local receptive field, which makes the model extract more valuable features. In addition, the nonlinear relationship between different convolution features is enhanced using the feature pyramid attention mechanism (PAM). The advantage of FESSD over other state-of-the-art target detection methods is validated by experiments on the presented seven-class target detection dataset (SD-RSI) and the public DIOR dataset.

This review article provides a comprehensive overview of the anatomical structure of the human brain, highlighting its key components and their functional significance. The brain is the central organ of the nervous system, responsible for controlling and coordinating various bodily functions. The article begins with an introduction to the brain's gross anatomy, including the cerebrum, cerebellum, brainstem, and diencephalon. It then delves into the detailed microstructure of the brain, discussing neurons, glial cells, and the complex network of neural connections. The review also explores the functional organization of the brain, emphasizing the roles of different regions such as the frontal, parietal, temporal, and occipital lobes. It discusses the importance of the limbic system in emotional processing and the basal ganglia in motor control. Additionally, the article covers the brain's vascular system and the blood-brain barrier, which are crucial for maintaining the brain's homeostasis. Recent advancements in neuroimaging techniques, such as magnetic resonance imaging (MRI) and functional MRI (fMRI), have significantly enhanced our understanding of brain anatomy and function. These techniques have enabled researchers to map brain activity in real-time, providing insights into cognitive processes and neurological disorders. The article concludes by discussing the implications of understanding brain anatomy for clinical practice, including the diagnosis and treatment of neurological conditions. It also highlights areas for future research, emphasizing the need for further exploration of the brain's structural and functional complexity.

The detection performance of small objects in remote sensing images has not been satisfactory compared to large objects, especially in low-resolution and noisy images. A generative adversarial network (GAN)-based model called enhanced super-resolution GAN (ESRGAN) showed remarkable image enhancement performance, but reconstructed images usually miss high-frequency edge information. Therefore, object detection performance showed degradation for small objects on recovered noisy and low-resolution remote sensing images. Inspired by the success of edge enhanced GAN (EEGAN) and ESRGAN, we applied a new edge-enhanced super-resolution GAN (EESRGAN) to improve the quality of remote sensing images and used different detector networks in an end-to-end manner where detector loss was backpropagated into the EESRGAN to improve the detection performance. We proposed an architecture with three components: ESRGAN, EEN, and Detection network. We used residual-in-residual dense blocks (RRDB) for both the ESRGAN and EEN, and for the detector network, we used a faster region-based convolutional network (FRCNN) (two-stage detector) and a single-shot multibox detector (SSD) (one stage detector). Extensive experiments on a public (car overhead with context) dataset and another self-assembled (oil and gas storage tank) satellite dataset showed superior performance of our method compared to the standalone state-of-the-art object detectors.

In the study of materials and macromolecules by first-principle methods, the bond order is a useful tool to represent molecules, bulk materials and interfaces in terms of simple chemical concepts. Despite the availability of several methods to compute the bond order, most applications have been limited to small systems because a high spatial resolution of the wave function and an all-electron representation of the electron density are typically required. Both limitations are critical for large-scale atomistic calculations, even within approximate density-functional theory (DFT) approaches. In this work we describe our methodology to quickly compute delocalization indices for all atomic pairs, while keeping the same representation of the wave function used in most compute-intensive DFT calculations on high-performance computing equipments. We describe our implementation into a post-processing tool, designed to work with Quantum ESPRESSO, a popular open-source DFT package. In this way we recover a description in terms of covalent bonds from a representation of wave function containing no explicit information about atomic types and positions.

Retired Electric vehicles (EVs) batteries are reused in second life energy storage applications. However, the overall performance of repurposed energy storage system (ESS) is limited by the unevenness of individual batteries use in it. Therefore, battery grading is required for optimal performance of ESS. Electrochemical impedance spectroscopy (EIS) based evaluation of battery aging is a promising way to grade lithium-ion batteries. However, it is not practical to measure impedance of mass retired batteries due to high complexity and slowness. In this paper, a broadband multi-sine binary signal (MSBS) perturbation integrated with multichannel EIS system is presented to measure impedance spectra for high-speed aging evaluation of lithium-ion batteries or modules. The measurement speed is multi-times higher than conventional EIS with single-channel configuration. The broadband MSBS is validated with reference sinusoidal sweep perturbation and corresponding root-mean-square error (RMSE) analysis is performed. Moreover, the accuracy of the presented multichannel EIS system is validated by impedance spectra measurement of Samsung INR18650-29E batteries and comparing it with those measured with commercial EIS instrument. A chi-squared error under 0.641% is obtained for all 8-channels. Since the non-linearity of battery has significant impact on quality of impedance spectra. Therefore, Kronig-Kramer (KK) transform validation is also performed.

Maritime search and rescue is a crucial component of the national emergency response system, which currently mainly relies on Unmanned Aerial Vehicles (UAVs) to detect the objects. Most traditional object detection methods focus on boosting the detection accuracy while neglecting the detection speed of the heavy model. However, it is also essential to improve the detection speed which can provide timely maritime search and rescue. To address the issues, we propose a lightweight object detector named Shuffle-GhostNet-based detector (SG-Det). First, we construct a lightweight backbone, named Shuffle-GhostNet, which enhances the information flow between channel groups by redesigning the correlation group convolution and introducing the channel shuffle operation. Second, we propose an improved feature pyramid model, namely BiFPN-tiny, which has a lighter structure while being capable of reinforcing small object features. Furthermore, we incorporate the atrous spatial pyramid pooling module (ASPP) to the network, which employs atrous convolution with different sampling rates to obtain multi-scale information. Finally, we generate three sets of bounding boxes at different scales – large, medium, and small – to detect objects of different sizes. Compared with other lightweight detectors, SG-Det achieves better tradeoffs across performance metrics, and enables real-time detection with an accuracy rate of over 90% for maritime objects, which shows that it can be better meet the actual requirements of maritime search and rescue.

In the leading/trailing edge’s adaptive machining of the near-net-shaped blade, a small portion of the theoretical part is retained for securing aerodynamic performance by manual work. However, this procedure is time-consuming and depends on the human experience. In this paper, we defined retained theoretical leading/trailing edge as the reconstruction area. To accelerate the reconstruction process, an anchor-free neural network model based on Transformer was proposed, named LETR (Leading/trailing Edge Transformer). LETR extracts image features from an aspect of mixed frequency and channel domain. We also integrated LETR with the newest meta-Acon activation function. We tested our model on the self-made dataset LDEG2021 on a single GPU and got an mAP of 91.9\%, which surpassed our baseline model, Deformable DETR by 1.1\%. Furthermore, we modified LETR’s convolution layer and named the new model after GLETR (Ghost Leading/trailing Edge Transformer) as a lightweight model for real-time detection. It is proved that GLETR has fewer weight parameters and converges faster than LETR with an acceptable decrease in mAP (0.1\%) by test results.

Diabetic patients need long-term and frequent glucose monitoring to assist in insulin intake. The current finger-prick devices are painful and costly which make noninvasive glucose sensors highly demanded. In this review paper, we discuss several advanced electromagnetic (EM) wave based technologies for noninvasive glucose measurement, including infrared (IR) spectroscopy, photoacoustic (PA) spectroscopy, Raman spectroscopy, fluorescence, optical coherent tomography (OCT) and microwave sensing. Development and progress of each method are discussed regarding fundamental principle, system setup and experimental results. Despite the promising achievements reported previously, there is no established product to obtain FDA approval or survive marketing test. Limitations and prospects of these techniques are discussed at the end of this review.

An accurate flux measurement of low-energy charged particles trapped in the magnetosphere is necessary for space weather characterization and to study the coupling between the lithosphere and magnetosphere, which allows for the investigation of the correlations between seismic events and particle precipitation from Van Allen belts. In this work, the project of a CubeSat space spectrometer, the Low-Energy Module (LEM), is shown. The detector will be able to perform an event-based measurement of the energy, arrival direction, and composition of low-energy charged particles down to 0.1 MeV. Moreover, thanks to a CdZnTe mini-calorimeter, the LEM spectrometer also allows for photon detection in the sub-MeV range, joining the quest for the investigation of the nature of Gamma-ray bursts. The particle identification of the LEM relies on the ΔE−E technique performed by thin silicon detectors. This multipurpose spectrometer will fit within a 10 × 10 × 10 cm3 CubeSat frame, and it will be constructed as a joint project between the University of Trento, FBK, and INFN-TIFPA. To fulfil the size and mass requirements, an innovative approach, based on active particle collimation, was designed for the LEM; this avoids the heavy/bulky passive collimators of previous space detectors. In this paper, we will present the LEM geometry, its detection concept, the results from the developed GEANT4 simulation, and some characterisations of a candidate silicon detector for the instrument payload.

Millimeter wave antennas have significance for high-speed, high-capacity wireless communication, delivering substantial advantages and an array of applications. This literature review analyzes the historical development, assessment of performance, difficulties with design, and contemporary applications in telecommunications, radar systems, and imaging. It covers the development of technology, especially within the context of 5G and beyond, and focuses at several antenna designs that deal with technical issues including reduction and impedance matching. The review also studies the effect of design on efficiency and bandwidth, identifying research gaps and potential futures, notably in terms of 5G technology. The commitment to develop millimeter wave antenna technology for next-generation wireless networks is evident, underlining the need of continued research and development.