Potassium-oxygen batteries (KOBs) are a promising energy storage technology with high theoretical en-ergy density, low overpotential and long cycle life. Cathode microstructure plays a significant role in the electrochemical performance of KOB. In this article, hierarchical porosity was introduced to commer-cially available carbon paper cathodes by the thermal pretreatment in air at different pretreatment times. This pretreatment modifies the properties, such as, surface area, defects, oxygen functional groups etc. and it has been found to enhance the discharge capacity and it result in reduction of dis-charge overpotentials.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

Sinkhole formation caused by leaking pipes in karst soluble rocks is a significant concern, leading to infrastructure damage and safety risks. In this paper, an experiment was conducted to investigate sinkhole formation in dense sand induced by a leaking pipe. Fibre Bragg gratings (FBGs) sensors were used to record the strain. A balloon was gradually deflated within a bed of wet silica sand to create an underground cavity. Eighteen FBG sensors, with a wavelength range between 1550 nm and 1560 nm, were embedded horizontally and vertically in the physical model at different levels to monitor deformation at various locations. A leaking pipe was installed to induce the collapse of the formed arch above the cavity. The strain measurements suggest four phases in the sinkhole formation process: (1) cavity formation, (2) progressive weathering and erosion, (3) catastrophic collapse, and (4) subsequent equilibrium conditions. The results showed differences in strain signatures and distributions between horizontal and vertical measurements. During the critical phase of sinkhole collapse, horizontal measurements primarily showed tension, while vertical measurements indicated compression. This investigation demonstrates the effectiveness of FBGs as advanced monitoring tools for sinkhole precursor identification. The study also suggests using FBGs in geotechnical monitoring applications to improve understanding and mitigation of sinkholes and related geohazards.

Sinkhole flooding is an essential hydrological process to recharge karst aquifer in arid to dry sub-humid regions. On the other hand, the increase of rain extremes is one of the major consequences of the global warming, together with the expansion of drylands. Thus, appropriate runoff regulation in endorheic karst basins in order to reduce the risk of flooding and improve the quantity and quality of the water drained by sinkholes will be more and more crucial. With these premises, a systematic review was performed by using WoS engine to infer the best practices for the karst water management in regions actually or potentially affected by water scarcity. Hydrological models are essential to manage the consequences of climate change on karst water resource, however the review shows that providing the tools necessary for reliable modeling is still challenging. Finally, due to the intrinsic vulnerability of the karst aquifers, pollution reduction and wastewater recycling policy will play key role in the next decades.

The persistence of symptoms following COVID-19 infection represents a significant challenge in healthcare management. During the outbreak, tele-rehabilitation emerged as a new tool to support healthcare structures in providing rehabilitation services. This study assessed the effectiveness and the feasibility of a 3-week home-based motor and respiratory rehabilitation program for long COVID-19 individuals after traditional rehabilitation. Twenty-three patients completed the program and underwent functional tests at different time points (i.e. baseline, after hospital discharge, and after tele-rehabilitation). Motor function was evaluated using the instrumented Six-Minutes Walking Test (i6MWT), with monitored heart rate and oxygen saturation. Conversely, respiratory function was measured via forced vital capacity (FVC) and maximal voluntary ventilation (MVV) tests. Significant improvements (p < 0.05) in motor and respiratory function were observed throughout the intervention, including an 18.3% increase in walked distance from the baseline. The findings suggest that a home-based tele-rehabilitation can enhance motor and respiratory function in post-COVID patients. Despite limitations such as sample size and lack of control group, the positive outcomes seem to support the feasibility of the proposed tele-rehabilitation program in managing long COVID symptoms and promoting functional recovery. Further research is needed to validate these findings and explore tele-rehabilitation’s potential in broader patient populations.

(1) Background: As part of the Scottish Governments five-year recovery plan to address the backlog in NHS care following the COVID-19 pandemic, community pharmacies in Scotland are planned to provide a Hospital Discharge Medicines Supply and Medicines Reconciliation Service. We aimed to qualitatively explore patients’ experience of this new service; (2) Method: Adult patients (≥18yrs age) who consented to participate in the Community Pharmacy Hospital Dis-charge and Medicines Reconciliation Service were invited for interview within 21 days of dis-charge from hospital. Qualitative, one-to-one, semi-structured, patient interviews were conducted by telephone and audio-recorded using Microsoft Teams®. The interview audio recordings were transcribed verbatim and underwent thematic analysis; (3) Results: 12 patients were inter-viewed, evenly split by sex and with a median age of 62 years (range; 36 to 88 years). Analysis generated main five themes; Patient Engagement, Stakeholder Communication, Practical Factors, Human Factors, and Comparative Experiences. Many of these were interdependent; (4) Con-clusions: Patients appreciated that the service ensured a quicker discharge from hospital. Good stakeholder communication, practical factors (including choice, location, and the realities of ob-taining their medication from the community pharmacy), and a pre-existing and trusted rela-tionship in their usual community pharmacy were the key factors that regulated the patient ex-perience. In the main, patients were positive about the introduction of this new service. However, a lack of previous relationship or trust with a community pharmacy, and previous experiences with medication supply problems were factors which had the potential to negatively impact on patient experiences.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

With the aim of developing an innovative water treatment approach for developing countries in the Global South, we have applied the method of treating a cavitating water stream with a plasma discharge under real conditions. To this end, we have optimised the approach after investigating the effects that occur in the treated medium during such a treatment. Based on the obtained light absorption curves of treated model solutions of titanium oxysulphate and potassium bichromate, it was found that inside the reactor the main role in the destruction of chemical contaminants is played by hydroxide ions, while outside the reactor the main chemical interaction takes place with hydrogen peroxide. The plasma treatment unit was tested in the biological wastewater treatment plants of a health resort on the territory of the Russian Federation (Almetyevsk, Republic of Tatarstan). Water samples taken directly from the tertiary decantation tank were used as real wastewater samples instead of adding chemical reagents for disinfection. It was found that with different modes of operation of the plasma treatment plant, the concentration levels of coliform bacteria, coliphages and Escherichia coli decrease significantly and fall below the limit of permissible concentrations for wastewater discharge. At the same time, the possible effect of the plasma on persistent inorganic compounds was investigated. It was shown that the plasma discharge in the flow of the incoming liquid can almost completely destroy compounds that are difficult to remove, such as hydrogen sulphide and chlorides. In the course of the study, the optimum frequency of the electrical pulses of 68 kHz was selected, which ensures the lowest consumption of electrical energy while maintaining the required efficiency.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

ABSTRACT Background: To date, the COVID-19 pandemic has been the foremost health concern for humankind in the new millennia. This paper aims to describe the related hospitalizations in Italy during the first two years of the health emergency. Design and methods: This is a retrospective, population-based study of Italian hospitalizations for patients diagnosed with COVID-19 during the 2020-2021 period, extracted from the National Hospital Discharge Registry. The outcome variables considered include hospital admissions, costs, and length of stay, among other hospitalization-level variables. Costs were estimated through the charges associated with the Diagnosis-Related Group and Major Diagnostic Categories coding system, plus an additional cost attributed to COVID-19 admissions. To these charges was added an extra cost defined by the ministry of health. Results: In Italy, there were 357,354 hospitalizations for COVID-19 attributed to 298,856 patients in 2020 and 399,043 hospitalizations for COVID-19 attributed to 333,447 patients in 2021. COVID-19 patients faced a transfer rate thrice that of other patients. Hospitalizations were concentrated predominantly in the northern regions, particularly in the first year. Hospitalization rates varied by age in a sine wave pattern, peaking in the youngest and oldest age groups, with mortality rates escalating with age— tending to remain below 3% for those under 44 but surging to 40% in individuals over 75. The financial impact of COVID-19 hospitalizations was substantial, with total costs reaching €3.97 billion in 2020 and €4.99 billion in 2021. Costs per admission and per day also rose, from €11,112 and €807 in 2020 to €12,503 and €844 in 2021, respectively. Excluding the added financial burden of COVID-19, costs would have been notably lower. Hospitalizations involving continuous invasive mechanical ventilation were particularly costly (about 24.000 euros x admission), reflecting the significant resources required for these treatments. Conclusion: Implementing a protective pad around the entire health system that leverages networks of family doctors and nurses, connected in real time to the entire health system, can be crucial. Such a network, tasked with monitoring the local epidemiological situation, protecting vulnerable individuals also through telehealth visits, and establishing a triage system for infections in the initial phase, may effectively help in managing virus spread and protecting hospitals from unpredictable waves of admission demand. Strengthening primary health care could be a decisive factor for the future and enhance the system's resilience in facing new challenges.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

The formation of sinkholes in Winkler County, Texas is concerning due to the amount of oil and gas infrastructure and the potential for catastrophic losses. Evidences of new and potential sinkholes have been documented, and determining the cause of these sinkholes is paramount to mitigate the devastating consequences thereof. Studies shown that the Wink sinkholes result from both natural and anthropogenic influences. Data depicting land-cover changes, alterations in the hydrologic systems, climate changes, and oil and gas activity were analyzed in an effort to better understand the link between these processes and sinkhole formation. Results indicate that the combination of these processes lead to the current state; Land cover changes were highest in shrub versus grasses, undeveloped to developed and croplands. Rises in temperature and a decrease in precipitation indicate a shift towards a more arid climate. Changes to the hydraulic system are a direct result of these land cover changes while the groundwater quality depict an environment prone to dissolution. Historical oil and gas activities have created pathways of meteoric water infiltration to the underlying limestone and evaporite formation. The combination of these processes create an environment that accelerates sinkhole formations. Understanding these processes allows for the development and implementation of better land practices, better groundwater protections, and the need for monitoring and maintaining aging oil and gas infrastructure.

Patients who survived critical COVID-19 frequently reported post-acute sequelae of COVID-19 (PASC) such as psychosomatic and neurocognitive health problems. The goal of this study was to identify clinical risk factors and other predictors for such long-term consequences in severely ill COVID-19 patients. Adult COVID-19 intensive care unit (ICU) survivors from August 2020 to May 2021 were enrolled. A broad range of clinical, laboratory and chest computed tomography (CT) data was collected during ICU stay. The association between ICU predictors and psychosomatic, respiratory and neurocognitive assessments 12 months after ICU discharge was analyzed using univariate regression analysis. In 17 patients (mean age 58.9 ± 11.4 years), laboratory markers (CRP, lymphocytes, hemoglobin), ICU severity (SOFA, SAPS II, need for mechanical ventilation), complications (ARDS), and lung CT data (ground-glass opacity) were promising predictors of depressive and anxiety symptoms, fatigue, and sleep problems. Recovery of psychosomatic health such as fatigue, depression and anxiety correlated with lower levels of inflammation and high hemoglobin levels. ARDS, mechanical ventilation and worse SOFA and SAPS II scores were further risk factors for depressive and anxiety symptoms. Our study identified novel associations such as pulmonary ground-glass opacity being positively associated with depression, anxiety, fatigue, and insomnia levels.

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

Fatigue and dyspnea are the most commonly presented long-term complaints in individuals previously infected with SARS-CoV-2. The purpose of the study was to comprehensively evaluate diaphragm muscle function in COVID-19 survivors, as well as investigate whether potential diaphragm dysfunction will contribute to physical functioning impairment. 46 patients qualified to pulmonary rehabilitation were examined. Diaphragm muscle function parameters were evaluated using ultrasonography, while severity of dyspnea, aerobic capacity and amount of energy used by the body during physical activity were assessed by 6-minute walk test, mMRC scale and Metabolic Equivalent Task (MET), respectively. We identified 69.5% patients with diaphragm atrophy and 6.5% with diaphragm paralysis. Percentage of atrophy was not related to age, gender, BMI index, oxygen therapy use during COVID-19 infection course and severity of disease. Patients with presence of cough, fever and without loss of smell during COVID-19 course had a significantly greater values of diaphragm inspiratory thickness, while patients with cough and no smell disorders had a significantly lower percentage of diaphragm atrophy. Diaphragm functional parameters were strongly associated with selected variables of person's exercise tolerance, such as distance in 6-minute walk test, saturation level, fatigue and exertion in Borg scale. In conclusion, diaphragm muscle dysfunction is a serious long-term post-COVID aftermath and can be viewed as a major contributing factor of prolonged functional impairments.

The targeted compounds in this research, resveratrol analogs 1–14 were synthesized as mixtures of isomers by the Wittig reaction using heterocyclic triphenylphosphonium salts and various benzaldehydes. The planned compounds were those possessing the trans-configuration as the biologically active trans-resveratrol. The pure isomers were obtained by repeated column chromatography in various isolated yields depending on the heteroaromatic ring. It was found that butyrylcholinesterase (BChE) was more sensitive to the heteroaromatic resveratrol analogs than acetylcholinesterase (AChE), except for 6, the methylated thiophene derivative with chlorine, which showed equal inhibition toward both enzymes. Compounds 5 and 8 achieved the highest BChE inhibition with IC50 values of 22.9 and 24.8 μM, respectively. The same as with AChE and BChE, methylated thiophene subunits of resveratrol analogs showed better enzyme inhibition than unmethylated ones. Two antioxidant spectrophotometric methods, DPPH and CUPRAC, were applied to determine the antioxidant potential of new heteroaromatic resveratrol analogs. Molecular docking of these compounds was conducted to visualize the ligand-active site complexes' structure and identify the non-covalent interactions responsible for the complex's stability, which influence the inhibitory potential. As ADME properties are crucial in developing drug product formulations, they have also been addressed in this work. The potential genotoxicity is evaluated by in silico studies for all compounds synthesized.

The marine region of the Zhongjieshan Islands is an essential component and location for enhancement and release in Zhoushan Fishing Ground. The scientific assessment of the target species' ecological carrying capacity serves as the foundation for augmentation and release efforts. Based on data from the 2021-2022 survey of biological resources in the waters of Zhongjieshan islands, the Ecopath model was built to analyze the trophic structure, energy flow, and overall characteristics of the ecosystem, as well as the ecological carrying capacity of the main enhancement and releasing species, Larimichthys crocea and Sepiella maindroni. The ecosystem's functional groups had trophic levels ranging from 1 to 3.48, with an average energy transfer efficiency of 8.11% and total flow of 2125.905 t·km-2. The ratio of total primary output to total respiration is 1.713. Zhongjieshan Islands' ecosystem was currently at an embryonic stage. The ecological carrying capacity of Larimichthys crocea and Sepiella maindroni was calculated to be 0.2325 t·km-2 and 0.1617 t·km-2, separately or individually. Larimichthys crocea and Sepiella maindroni showed enormous potential for development and release. The findings offered essential data for ecological studies on the waters of Zhongjieshan Islands, as well as a reference for enhancement and release efforts in this area.

Concerns regarding the safety of ethoxyquin (EQ) have gradually increased, highlighting the necessity of identifying safer and more effective antioxidants for use in animal feed. This study investigates the effects of a compound antioxidant (CA) as an alternative to ethoxyquin on feed oxidative stability, growth performance, antioxidant capacity, and intestinal health in broilers. A total of 351 one-day-old Arbor Acres Plus male broilers were randomly assigned to three treatments with nine replicates of 13 birds each. The experimental treatments included: CON group (basal diet), EQ group (basal diet + 200 g/ton EQ at 60% purity), and CA group (basal diet + 200 g/ton compound antioxidant, which comprises 18% butylated hydroxytoluene, 3% citric acid, and 1% tertiary butylhydroquinone). The experiment lasted for 21 days. Compared to the control group, supplementation with CA significantly reduced the acid value, peroxide value, and malondialdehyde content in the feeds after storage. Moreover, CA supplementation significantly decreased feed intake and the feed conversion ratio (FCR) without affecting weight gain of boilers, while also improving liver antioxidant capacity (increased T-AOC and SOD levels), intestinal antioxidant capacity (increased CAT, HO-1, and GPX7 protein expression), and enhancing the duodenal villus height-to-crypt depth ratio and jejunal villus height. Additionally, CA treatment reduced intestinal barrier permeability (decreased diamine oxidase activity and D-lactate levels), potentially by promoting the expression of Occludin, ZO-1, and Mucin2 protein. Furthermore, the addition of CA elevated the protein levels of NF-κB p50 along with its inhibitory factors, IκB and NF-κB p105, in the intestines of broilers, thereby enhancing immune regulatory capacity. This supplementation also led to an increased abundance of beneficial gut microorganisms, including Lactobacillus, Alistipes, Candidatus Arthromitus, and Turicibacter. In comparison to the EQ group, CA supplementation enhanced feed oxidative stability, decreased the FCR, and improved the intestinal morphology, barrier functions, and inflammatory status in broilers. These findings suggest that this compound antioxidant may serve as a healthier and more effective alternative to ethoxyquin.

Optical backbone networks constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is a key factor influencing optical network performance, it is important to understand how topological and physical properties impact its behavior and to have the capability to estimate its value. In this context, we propose here a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with constrained routing techniques for traffic routing. As this type of routing can lead to traffic blocking, particularly due to the limitation on the number of wavelengths per fiber, we also propose a fiber assignment algorithm designed to deal with this problem. We apply this method to a set of randomly generated networks using a modified Waxman model, and for a network with 60 nodes, in a scenario without blocking, we obtain capacities of about 2.5 Pbit/s for a symbol rate of 64 Gbaud and about 5 Pbit/s for a symbol rate of 128 Gbaud. Remarkably, this duplication in the total network capacity is achieved by an increase in the total fiber length of only about 51%.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

In this study, we evaluated the antibacterial effect against Staphylococcus aureus and Salmonella Typhimurium in fried fish paste using floating electrode-dielectric barrier discharge (FE-DBD) plasma (1.1 kV, 43 kHz, N2 1.5 m/s, 1-60 min). In addition, quality evaluation (pH, VBN) of fried fish paste was conducted after FE-DBD plasma treatment. When FE-DBD plasma was treated for 1, 5, 10, 20, 30 and 60 min, S. aureus decreased by 0.16-1.13 log10 CFU/g, and S. Typhimurium decreased 0.25-1.13 log10 CFU/g. Both decreased &gt; log10 CFU/g at 60 min. The D-value was 58.92 and R2 was 0.97 for S. aureus using first-order kinetics, and the D-value was 43.60 and R2 was 0.97 for S. Typhimurium using the Weibull model. There was no significant difference in pH after FE-DBD plasma treatment (p &gt; 0.05). However, volatile basic nitrogen (VBN) significantly decreased as the treatment time increased (p &lt; 0.05), and it was the lowest at 60 min to 3.46. Therefore, FE-DBD plasma treatment could be considered as a technology for preserving the quality of processed foods.

Digital transformation provides new drivers for economic performance growth in enterprises, but can it further improve ESG performance and support sustainable development? Based on the perspective of resources and capabilities, this paper uses the relevant data of 1588 listed companies in strategic emerging industries from 2011 to 2021 to study the differential impact of digital transformation on enterprise ESG performance, and further tests the mediating role of absorptive capacity and the moderating role of regional digital level. The research results indicate that: firstly, digital transformation of enterprises can positively promote the improvement of ESG performance; Secondly, there are significant differences in the impact of digital transformation on the ESG performance of enterprises in terms of property rights and industry characteristics. The ESG performance of state-owned enterprises and high-end equipment manufacturing enterprises is more sensitive to digital transformation; Thirdly, absorptive capacity plays a mediating role between digital transformation and corporate ESG performance; Fourthly, the positive regulation of regional digital level promotes the ESG performance of enterprises through digital transformation. The research conclusion is based on a digital perspective, providing relevant insights for improving the ESG performance of strategic emerging industry enterprises and expanding their ESG development paths.

A novel plasma source of pulsed electrolyte cathode atmospheric pressure discharge (pulsed-ECAD) driven by an alternating current (AC) power supply coupled with a high voltage diode was generated, and the discharge was generated in the open-to-air atmosphere between a metal electrode and a small-sized flowing liquid cathode. The spatial distribution of plasma temperatures (excitation, vibrational and rotational) of the pulsed-ECAD were investigated. The electron excitation temperature of H T_exc(H), vibrational temperature of N₂ T_vib(N₂), and rotational temperature of OH T_rot(OH) were measured as 4900±36-6800±108 K, 4600±86-5800±100 K and 1050±20-1140±10 K, respectively. Meanwhile, the temperature characteristics of dc solution cathode glow discharge (dc-SCGD) were also studied for comparison with pulsed-ECAD. The effects of operating parameters, including discharge voltage and discharge frequency, on the plasma temperatures were investigated. The electron number density determined in the discharge system and dc-SCGD were within the range (3.8–18.9) ×10¹⁴ cm^-3 and 2.6×10¹⁴-17.2×10¹⁴ cm^-3, respectively.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

Africa, home to the world's second-largest population of approximately 1.3 billion, grapples with significant challenges in meeting its medical needs, particularly in accessing quality healthcare services and products. The continent faces a continuous onslaught of emerging infectious diseases, exacerbating the strain on its already fragile public health infrastructure. The emergence of SARS-Cov2 has further exposed the deficiencies in Africa's public health response, ranging from limited diagnostic capabilities to difficulties in vaccine distribution. Compounding these challenges is vaccine hesitancy, which is prevalent in many regions due to varying levels of understanding and trust regarding vaccines. The disparities in vaccine literacy across the continent stem from a complex interplay of factors, including low literacy rates and a history of medical exploitation and misinformation campaigns. These factors have led to a pervasive distrust in medical institutions and healthcare providers among certain African communities. Despite concerted efforts by national governments, private entities, and international partners to address these challenges and improve vaccine literacy, significant hurdles persist. This manuscript examines the current state of education in vaccinology and related sciences in Africa, as well as the continent's efforts to address educational needs in vaccine development and manufacturing. It evaluates initiatives aimed at strengthening vaccine education and literacy, highlighting successful approaches and ongoing challenges. By assessing the progress made and identifying remaining obstacles, this review offers insights into how Africa can enhance its capacity in vaccinology and accelerate its contributions to global health security.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

In this study, Acısu Basin, which is upper side of one of the most important basins (Gediz) in Türkiye, was modelled using three types of hydrological models and three different calibration algorithms. Lumped (GR4J), semi-distributed (SWAT+), and fully distributed (mHM) hydrological models were built and integrated with Parameter Estimation Tool (PEST) which is a model independent calibration tool including various algorithms. Levenberg Marquardt (L-M), Shuffled Complex Evolution (SCE), and Covariance Matrix Adoption Evolution Strategy (CMA-ES) were selected as calibration algorithms. Calibration period was 1991-2000, and validation results were obtained for 2002-2005. The effect of model structure and calibration algorithm selection on discharge simulation was evaluated via comparison of 9 different model-algorithm combinations. Results have shown that mHM and CMA-ES combination showed the best discharge simulation performance according to NSE values (calibration: 0.67, validation: 0.60). Although statistically the model results were classified as acceptable, the pattern comparison of discharge value shows that all of the models miss the peak values in significant amounts. This problem may be related to the interventions made in 2000-2001 years interval and possible to overcome by changing the calibration and validation periods, increasing the number of iterations or using the naturalized gauge data.

Objective: To investigate whether the relationships between acute care occupational therapy (OT) and physical therapy (PT) utilization and community discharge are moderated by functional or physical performance at discharge among individuals hospitalized with traumatic brain injury (TBI). Setting: 14 acute care hospitals in the state of Colorado. Participants: We studied 5,599 adults hospitalized with TBI between June 2018 and April 2021. Design: In a secondary analysis of de-identified electronic health record (EHR) data, multivariable moderation logistic regression models were performed to calculate odds ratios (ORs) for the likelihood of community discharge among patients who utilized OT/PT services. Main Measures: Functional (activities of daily living [ADL]) and physical (mobility) performance at discharge, OT and PT utilization, and community discharge status. Results: Overall, 67% of patients discharged to the community. The mean age of the sample was 55 years (SD = 20 years). Most participants were male (64%) and non-Hispanic white (72%). Mean hospital length of stay was 6 days (SD = 6 days). Both OT and PT utilization (OT: OR= 1.21, 95% CI [1.11, 1.33]; PT: OR= 1.22, 95% CI [1.14, 1.30]) and discharge ADL and mobility scores (ADL: OR= 1.34, 95% CI [1.30, 1.39]; mobility: OR= 1.38, 95% CI [1.33, 1.42]) were significantly and positively associated with community discharge. The OT and PT utilization-by-discharge ADL and mobility interaction terms yielded slightly negative, but statistically significant moderation effects in both models (ORs= 0.99, 95% CIs [0.98, 1.00]); indicating the magnitude of the OT and PT utilization effect diminished as ADL and mobility scores increased. Several sociodemographic characteristics and clinical factors were also independently associated with community discharge in both models (p-values

Dielectric barrier discharge (DBD) plasma has several applications in different fields. One of these fundamental applications is medical usages, where various methods are employed to improve the plasma treatment process. The combination of different gases is one of the important strategies to improve the performance of plasma in treatment. In this paper, the optimized plasma parameters for one-dimensional radiofrequency discharge produced at low pressures in a helium gas combination is studied. In this research, the optimal combination of H₂O and He is identified to attain the highest amount of reactive oxygen species (ROS). Considered mixture are 5,10,15 and 20 precent of H₂O for one dimensional helium gas discharge. The results show that the parameters of the output plasma are highly dependent on the composition of the input gases. It is found that the greatest concentrations of H+, He+, Hes (excited helium), and OH/ densities are observed when the H₂O percentage is 10%. Moreover, the density distributions of various species and the temperatures of electrons are numerically calculated during the electrical discharge process. These findings provide useful knowledge on how to optimize plasma parameters for biomedical applications, which may lead to improved treatment results in several therapeutic areas.

The properties of coatings obtained using two surface preparation methods were compared: heating and etching by ion bombardment with plasma generation by arc evaporators and heating and etching by a glow discharge. A Ti-TiN-(Ti,Cr,Al)N coating was deposited. The use of a glow discharge provides better resistance of the coating to destruction during the scratch test and wear resistance of metal-cutting tools when turning steel. As the cutting speed increases, the advantage in wear resistance of the coating deposited using a glow discharge increases. During the process of heating and etching by ion bombardment with metal ions, a nanolayer rich in cobalt and tooling elements (iron, molybdenum) is formed in the area of the interface of the coating and the carbide substrate. When heated and etched by a glow discharge, such a layer does not form. When using both methods, there is identical diffusion of tungsten into the coating and diffusion of chromium and possibly titanium into the substrate. Thus, the glow discharge heating and etching method can be effectively used in the process of PVD coating deposition.

Background: Mental capacity is a fundamental aspect that enables patients to fully par-ticipate in various healthcare procedures. To assist healthcare professionals (HCPs) in assessing patients' capacity, especially in the mental health field, several standardized tools have been developed. These tools include the MacArthur Competence Assessment Tool for Treatment (MacCAT-T), the MacArthur Competence Assessment Tool for Clinical Research (MacCAT-CR), and the Competence Assessment Tool for Psychiatric Advance Directives (CAT-PAD). The core dimensions explored by these tools include Understanding, Appreciation, Reasoning, and Expression of a choice. Objective: This meta-analysis aimed to investigate potential differences in deci-sion-making capacity within the healthcare context among groups of patients with bi-polar disorder (BD) and schizophrenia spectrum disorder (SSD). Methods: A systematic search was conducted on Medline/Pubmed, and Scopus. Addi-tionally, Google Scholar was manually inspected, and a manual search of emerging re-views and reference lists of the retrieved papers was performed. Eligible studies were specifically cross-sectional, utilizing standardized assessment tools, and involving pa-tients diagnosed with BD and SSD. Data from the studies were independently extracted and pooled using random-effect models. Hedges g was used as a measure for outcomes. Results: Six studies were identified, with three studies using the MacCAT-CR, two studies the MacCAT-T, and one the CAT-PAD. The participants included 189 individuals with BD and 324 individuals with SSD. The meta-analysis revealed that patients with BD performed slightly better, and the difference was statistically significant, compared to patients with SSD, particularly in the domain of Appreciation (ES=0.23, 95% CI: 0.01 to 0.04, p=0.037). There was no statistically significant difference between the two groups for Understanding (ES=0.09, 95% CI: - 0.10 to 0.27, p=0.352), Reasoning (ES=0.18, 95% CI: - 0.12 to 0.47, p=0.074), and Expression of a choice (ES = 0.23, 95% CI: - 0.01 to 0.48, p=0.60). In the sensitivity analysis, furthermore, when considering only studies involving patients in symptomatic remission, the difference for Appreciation also resulted in non-significant (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). Conclusions: These findings indicate that there are no significant differences between patients with BD and SSD during remission phases, while differences are minimal during acute phases. The usefulness of standardized assessment of capacity at any stage of the illness should be considered, both for diagnostic-therapeutic phases and for research and advance directives. Further studies are necessary to understand the reasons for the overlap in capacity between the two diagnostic categories compared in this study.

The antioxidant properties and polyphenol content of some selected aromatic plants grown in Greece were studied. Plants were refluxed with 60% methanol after acid hydrolysis. The phenolic substances were quantified by HPLC-DAD. The antioxidant capacity of the extracts was determined with the Rancimat test using sunflower oil as substrate. Free radical scavenging activity was measured using the stable free radical 1, 1-diphenyl-2-picrylhydrazyl (DPPH). Results were compared with standard BHT and ascorbic acid. Total phenol concentration of the extracts was estimated with Folin-Ciocalteu reagent using gallic acid as standard.

Accurate estimation of livestock carrying capacity (LCC) and implementing an appropriate actual stocking rate (ASR) is key to sustainable management of grazing adapted alpine grassland ecosystems. Reliable determination of aboveground biomass is fundamental to these determinations. Peak aboveground biomass (AGBP) captured from satellite data at the peak of the growing season (POS) is widely used as a proxy for annual aboveground biomass (AGBA) to estimate LCC of grasslands. Here we demonstrate limitations of this approach and highlight the ability of POS in the estimation of ASR. We develop and trail new approaches that incorporate remote sensing phenology timings of grassland response to grazing activity, considering relations between biomass growth and consumption dynamics, in efforts to support more accurate and reliable estimation of LCC and ASR. Results show that based on averaged values from large-scale studies of alpine grassland on the Qinghai-Tibet Plateau (QTP), differences between AGBP and AGBA underestimate LCC by about 31%. Findings from a smaller-scale study that incorporate phenology timings into estimation of annual aboveground biomass reveal that Haibei alpine meadows were overgrazed by 11.5% during the study period from 2000-2005. The methods proposed can be extended to map grassland grazing pressure by predicting LCC and tracking ASR, thereby improving sustainable resource use in alpine grasslands.

Admission and discharge diagnoses of in-hospital patients are often in discord. Incorrect admission diagnoses are related to increased cost of care and patient safety. Additionally, due to the seasonality of many conditions, this discord may vary across the year. In this paper, we used medical claims data to develop a methodological framework that examines these differences, for Medicare beneficiaries. We provide examples for pneumonia, a condition with seasonal implications, and aneurysm, where early detection can be life-saving. Following a Bayesian approach, our work quantifies and visualizes with time series plots the degree that any clinical condition is correctly diagnosed upon admission. We examined differences in weekly intervals, during a calendar year. The mean length of stay and hospital charges were furthermore compared between matching and non-matching {admission, discharge Dx} pairs, and 95% confidence intervals of the difference of means were estimated. We applied Statistical Process Control methods and then visualized differences, for the hospital charges and the length of stay, per week, with time series plots. Our methodology and the visualizations underline the importance of a rigorous and non-delayed diagnostic process upon admission since there are significant implications in terms of hospital outcomes and cost of care.

This paper presents the experimental campaign conducted near the Condoroma dam at 4075 m a.s.l. in an experimental setup consisting of a series of standard profile spillways with a vertical upstream face of up to five different dimensionless heights (P/Hd). The experimental results indicate that for all P/Hd ratios studied, the discharge coefficients adjusted to the Condoroma altitude are lower than those reported by classical formulations used in conventional spillway design. As a result, a generalized equation is proposed to estimate the discharge coefficient for standard spillways located in dams at similar elevations above sea level.

Financial capacity instruments are psychometric tools designed to evaluate individual decisional capacity based on financial decisions. As tests are complex and need special conditions for administration and evaluation, it is difficult to use them in daily geriatric clinics. Our scoping review objective was to evaluate existing financial capacity instruments from the perspective of simplicity and portability. We evaluated one English speaking knowledge database (Medline) using a dedicated MeSH terminology. The review yielded one independent instrument, The Semi-Structured Clinical Interview for Financial Capacity, that can be easy adapted for every-day clinical use. It is simple to understand and perform and do not need trained personnel for administration. It can be finalized in 15 minutes. Initially validated on 261 subjects (with different forms of cognitive impairment), it showed good accuracy and precision mainly in subjects with cognitive impairment. The test is less apt to detect early or fluctuating cognitive impairment. Simplicity, the main advantage of the test, allows gamification fact that increases portability. Familiar images (coins, money) that are used for performing simple tasks does not need complex translation and adaptation. In form of a game, the test is suitable for serial administration, increasing the chance for early capacity reduction detection. Results reflect a physician judgement related to the subjects’ capacity to understand and execute simple financial instructions and not financial proficiency scores. The main limitation of our review is that we investigated only one, English speaking, knowledge database. The scoping strategy generated a financial capacity instrument that can be used in geriatric clinics for early diagnostic of decisional capacity reduction. Further studies are needed to evaluate the reliability and validity of the test in conditions of serial administration and in populations having various financial experience.

The relentless challenges posed by the COVID-19 pandemic have placed immense pressure on densely populated regions, such as Hong Kong, particularly in the context of an aging population. The burgeoning demand for healthcare services has necessitated the optimization of resource al-location within healthcare systems. This research presents an innovative analytical queueing model specifically tailored to address the intricate gridlock dynamics prevalent in healthcare systems, with a focused application in the challenging landscape of COVID-19 management. Hong Kong, like numerous other regions, has experienced a demo-graphic transition leading to heightened healthcare demands. Traditional methodologies for scrutinizing gridlock issues in healthcare settings, including simulation models, often prove suboptimal within the context of sophisticated optimization frameworks. This study, however, delves into analytical queueing models, offering a more efficient and effective approach. These models have been underexplored, primarily due to the intricacies involved in modeling gridlock propagation within restricted capacity, a critical concern magnified by the COVID-19 pandemic. The novel Queueing Model introduced in this research incorporates the maintenance of queue capacities and topological aspects as exogenous parameters, rendering it exceptionally adaptable for diverse gridlock-related applications. This adaptability is especially pertinent to healthcare management during the COVID-19 crisis. The model meticulously integrates the concept of gridlock, furnishing a comprehensive comprehension of its origins and repercussions. Validation of this model involves rigorous comparison with established methodologies, exact results, and simulation data, consistently high-lighting its versatility and precision. By applying the model to healthcare management, we scrutinize the dynamics of patient flow within a Hong Kong hospital, placing specific emphasis on the critical issue of bed blockage, further exacerbated by the COVID-19 pandemic. The model's gridlock decomposition unearths the nuanced impact of bed blockage on distinct hospital units, addressing the imperative requirement for quantifying in-patient bed blockage within healthcare systems during a pandemic.

We report on the role of synergistic polarization of Ba0.9Sr0.1TiO3 (BST) nanoparticles in sulfur cathodes to enhance the redox kinetics of polysulfides for high-capacity Li-S batteries. Ferroelectric nanoparticles are known to significantly improve the electrochemical performance of Li-S batteries due to their inherent self-polarization and high adsorption capacity towards polysulfides. X-ray diffraction spectra confirmed the tetragonal symmetry (c/a=1.0073), while Raman spectroscopic analysis validated the presence of tetragonal orientation Raman modes in BST-modified composites. Scanning electron microscope (SEM) images showed a homogeneous distribution of BST in the sulfur cathode system, with grain sizes ranging from 1 to 1.5 μm. Notably, the BST-coupled S50BST30CB10PVDF10 composite cathode achieved a capacity of approximately 820 mAh/g at 100 mA/g, maintaining stability over 100 cycles, demonstrating improved electrochemical performance. Two distinct plateaus between 2.3 V to 2.0 V and 2.0 V to 1.5 V further underscore the superior performance of BST ferroelectric nanoparticles in enhancing the redox kinetics of Li-S batteries. By leveraging the favourable affinity of polar substances towards polysulfides, we aimed to create a more stable reactive environment within the cathodic site, effectively trapping polysulfide intermediates through the synergistic polarization of BST nanoparticles. The synergistic polarization induced by the asymmetric crystal structure of ferroelectrics is anticipated to generate internal electric fields, enhancing chemisorption with heteropolar reactive. The observed high cyclic stability further validates the efficacy of these composite cathodes in mitigating the polysulfide shuttle effect, offering promising prospects for advancing Li-S battery technology.

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

Earthquakes often entail alterations in the groundwater flow regime, in the phreatic level, in the surge and loss of springs, and discharge in brooks and springs. As for the latter, there are diverse feasible mechanisms, so there is a variety of theoretical approaches to elucidate the post-earthquake effects on spring discharge. This study adopts a conceptual approach, primarily presenting various methods for estimating water released by earthquakes by calculating discharge surpluses in springs. This study delves into refined techniques rooted in groundwater hydraulics, displaying applications of analytical and simulation methodologies to quantify seismic-induced groundwater discharge in springs. Investigating springs as natural indicators, this research applies mathematical precipitation-runoff models, specifically the CREC model, for simulating hydrographs in post-earthquake scenarios. We apply analytical procedures or mathematical simulation techniques employed in groundwater hydraulics for natural aquifer recharge calculations. Firstly, we briefly describe the methods based on the analysis of depletion curves of hydrographs in spring discharge. Additionally, certain mathematical rainfall-runoff models utilized in simulating hydrographs of karstic springs, along with derived analytical approximations, are adapted for this scenario. These hydraulic calculations involve the depletion coefficient and hydrodynamic volumes of aquifers, parameters that reveal certain aspects of the relation between groundwater and earthquakes, such as: a) Acknowledging faults as the primary geological structures in transmitting pore pressures due to earthquakes. b) Clarifying mechanisms of permeability enhancement during earthquakes. c) Highlighting the substantial volumes in motion within the Earth's interior, which, for instance, could constitute a significant source for the origin of mineral deposits. The findings highlight diverse features of the complex interplay between hydrogeological and tectonic processes at challenging spatial and temporal scales.

Patients hospitalized with COVID-19 are at a higher risk of thrombotic events following discharge, however the role of extended thromboprophylaxis remains controversial. The purpose of this study is to evaluate current extended post-discharge thromboprophylaxis practice and its outcomes.This study was a single-center, retrospective chart review of patients within Hennepin Healthcare hospitalized with COVID-19 from April 1^st 2020 to December 31^st 2021 with increased risk of thrombotic event based on D-dimer. The primary outcome was to describe current prescribing practices based on the number of patients who were eligible and received anticoagulants on discharge. Secondary outcomes included comparing the patient’s risk for thromboembolism based on a modified International Medical Prevention Registry on Venous Thromboembolism (IMPROVE-VTE) score to the current internal prescribing practice guideline, evaluating efficacy outcomes based on new thromboembolic events, and assessing safety of extended-thromboprophylaxis using the International Society of Thrombosis and Hemostasis criteria for major bleeding within 30 days of hospitalization discharge.Of 1984 patients who were hospitalized with COVID-19 infection, 961 patients were eligible to receive thromboprophylaxis at discharge, with a total of 191 patients who received anticoagulation according to the Hennepin Healthcare practice guideline. However, using the IMPROVE-VTE score, only 206 patients qualified for post-discharge thromboprophylaxis, and 63 total patients received anticoagulation. A new thromboembolic event occurred in 20 patients (5.8%) and 14 patients (4.1%) experienced major bleeding.The Hennepin Healthcare guideline for extended thromboprophylaxis at discharge encompassed more patients compared to the IMPROVE-VTE score. The incidence of a new thromboembolic event and major bleeding were low in both groups, although venous thrombotic events occurred more in thromboprophylaxis group than in patients who did not receive anticoagulation at discharge, more clinical data are needed for a conclusion.

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

This work is an addition to the previously developed two-dimensional model of the shock-plasma interaction extending it into the third dimension. The model allows tracing the evolution of the state of the hypersonic flow and the shock front refracted at a thermal discontinuity. The advantages of using the spherical coordinate system for this type of the problems include more transparency in interpreting the solution and a shortened calculation procedure, because all the changes to the front become reduced to one distortion component only. Although the vorticity generation triggered at the interface is the consequence of the refraction and tied to the steep changes of the front, it is shown here that it is not because of an instant parameter jump at the interface due to refraction itself.

Disposal and treatment of excess sludge is a huge problem in waste water treatment plants. Discharge plasma oxidation is an effective approach for sludge dewatering and digestion. In this study, the excess sludge disintegration by non-thermal discharge plasma coupled with thiosulfate (TSA) was investigated. The soluble chemical oxygen demand (SCOD) increased to 404.93 mg L-1 after 20 min of single discharge plasma treatment, and it further increased to 549.08 mg L-1 after adding 15 mmol L-1 of TSA; the water content of filter cake also further decreased in the presence of TSA. There existed an appropriate TSA dosage. In the discharge plasma coupled with TSA system, reactive oxygen species (·OH and ·O2-) were produced and played important roles in sludge disintegration. The addition of TSA promoted the production of ·OH. These reactive oxygen species destroyed the floc structures and promoted the transformation of organic substances, leading to reduction in average size of sludge flocs. The ratio of soluble extracellular polymer substances (S-EPS) was enhanced, while the ratio of tightly bound fraction was reduced after treatment. Thus, discharge plasma coupled with TSA promoted the lysis of microbial cells and released intracellular organic matter and bound water, finally improving sludge dewaterability.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

Detection of partial discharge (PD) activities in high-voltage equipment can be done according to the several mechanisms of signal detection, which are electromagnetic wave signal detection, acoustic signal detection, chemical reactions, electrical signal detection, or optical emission detection. Recently, multiple methods of detection and localization of partial discharge activities occurred in power transformers and gas-insulated switchgear (GIS) have been proposed to monitor the health condition of high-voltage equipment, especially when the awareness regarding preventive maintenance has been emphasized at the industrial level and electrical providers. In aligning the needs of industrial and the improvement of PD detection methods, this manuscript focused on reviewing the current practice methods for the detection and localization of PD signals in high-voltage equipment and comparing their efficacy, in summarizing the future direction of research work-related methods of PD detection. The comparative reviews are discussed in terms of the mechanism of PD signal detection, indication parameters, calibration technique, advantages, and limitations of each method of PD measurement in detail.

Negative corona discharges occur widely in high voltage transmission lines and charged aircraft, which can cause strong electromagnetic interference. Negative corona discharge is typically performed simultaneously at multiple discharge points. In this study, the current and its EM radiation characteristics of single-needle and multi-needle negative corona discharge in different conditions were tested. The current and electromagnetic radiation characteristics of the two discharge structures were compared. The dipole radiation model was established to analyze the EM radiation characteristics of the negative corona discharge.The results show that, It is only when the voltage reaches a certain threshold that the current and electromagnetic radiation fields of the multi-needle discharge structure will be superimposed and their amplitudes will increase significantly. The frequency of electromagnetic radiation signal does not change with the number of needles, cathode geometry and applied voltage, but only depends on ambient pressure. It provides a basis for detecting corona discharge sources under different conditions.

The RMA11 water quality model, which has been previously calibrated and validated, was coupled with the RMA10 3D hydrodynamic model to evaluate sanitation scenarios in Buenaventura Bay. The bay receives direct discharge of untreated wastewater from 500,000 people through 695 outlets along the coast. Five different effluent reduction scenarios were proposed and compared based on fecal coliform concentration as an indicator. The areas where values exceed the standard for primary contact were also used to evaluate the scenarios. The model results indicate poor water quality in the bay and how that the situation will become even more severe if immediate action is not taken. The proposed reduction in discharges in stages will have temporarily more severe effects than the current situation, but these will end when the treatment plant becomes operational. However, even with the plant in operation, complete sanitation of the bay cannot be achieved, and further measures must be considered.

This work communicates cavity ring-down spectroscopy (CRDS) of methylidyne (CH) in a chemiluminescent plasma that is produced in a microwave cavity. Of interest are the rotational lines of the 0-0 vibrational transition for the A-X band and the 1-0 vibrational transition for the B-X band. The reported investigations originate from CH-radical research in 1996 that constituted the first case of applying CRDS to the CH radical. The report also includes recent analysis that shows excellent agreement of measured and computed data, and it communicates CH line strength data.

The on-site wastewater treatment system (OWTS) with a sand trench is an economical option for residents in rural areas or the countryside where a centralised sewer system is inaccessible. 2A sand achieves improved filtration, microbial activity and consistent long term performance when compared to gravel or scoria based trench systems. However, it is expensive and only readily available in a few areas across New Zealand. Additionally, it has a reputation for premature blockage when overloaded or compacted. The aim of this study is not only to critically evaluate the performance of Crushed Glass (CG) with respect to 2A sand, but also to investigate different loading rates for CG when treating primary treated effluent from a septic tank. A test rig was designed and constructed to simulate the real environment of the sand column in a discharge control trench. The treatment efficiency of three filters was recorded and compared in this study. Overall, the CG loaded at 25mm/day (CG₂₅) and 50mm/day (CG₅₀) provided an average of 13% and 6% more Total Nitrogen (TN) reduction than the sand filter, respectively. The removal rates for the TN were up to 69.5%. The CG₅₀ filter performed similarly at 50mm/day as the 2A sand filter in terms of Total Suspended Solids (TSS) and Biochemical Oxygen Demand (BOD)₅ removal of more than 94%. The CG₂₅ removal rates for TSS and BOD₅ at the start of the trial (likely due to residual liquid contamination from the bottles when crushed) improved over the sampling period and ultimately achieved similar results of 92% and 91.3% to the filters loaded at 50mm/day. Lifecycle cost analyses and carbon balances were completed for the two media. It highlighted that the current price of CG is only half of 2A sand, yet it produces significantly less CO₂ emissions than 2A sand. A 3-bedroom dwelling could save up to $500 and reduce 200kg of CO₂ released to the environment annually when 2A sand is substituted for CG. Based on the findings of this paper, it is likely that the reduced installation cost, lessened environmental impact and theoretical availability will lead to CG systems becoming more common in New Zealand and abroad.

Abiogenic hydrocarbons are fundamentally important for understanding the deep microbial communities and the origin of life. The generation of abiogenic hydrocarbons was proposed to be limited to ultramafic-hosted hydrothermal systems, fueled by the serpentinization product H₂. Here, we present the discharge of short-chain alkanes from an andesitic rock-hosted Lutao geothermal field in the north Luzon arc, carrying abiotic chemical and isotopic signals. These abiogenic hydrocarbons were generated from CO₂-H₂O-rich fluid inclusions, where the long-term storage since Lutao volcanism (~ 1.3 Ma) allowed overcoming the sluggish kinetics of CO₂ to CH₄ reduction at temperatures of 174 - 206 ^oC. Natural abiogenic production of hydrocarbons, therefore, can be more ubiquitous than previously thought. The hypothesis regarding the origin of methane in Earth’s early atmosphere and its implication to the origin of life may require reconsideration.

Optical networks, characterized by using optical fibers as a transmission medium, constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is one of the key factors influencing optical network performance, it is important to comprehend its limitations and have the capability to estimate its value. In this context, we revisit the concept of capacity from various perspectives, including channel capacity, link capacity, and network capacity, thus providing an integrated view of the problem. Hence, we review the fundamental concepts behind optical networks, along with the basic physical phenomena present in optical fiber transmission and provide methodologies for estimating the different types of capacities, mainly using simple formulations. In particular, we propose a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with capacitated routing techniques for traffic routing. We apply this method to three reference networks and obtain capacities ranging from tens to hundreds of Terabits/s. Whenever possible, we also compare our results with published experimental data to understand how they relate.

To identify factors associated with interstitial lung disease (ILD) in patients with systemic sclerosis (SSc) and build an algorithm to better define this association, for a personalized application in clinical practice. Methods. 78 SSc patients underwent HRCT to assess ILD. Demographic, clinical and laboratory variables were collected, focusing on those associated either directly or indirectly with lung involvement. The discriminant value of each variable was determined using the operating characteristic curves (ROC) and included in a model to estimate the strength of ILD association in SSc. Results. Thirty-three (42.31%) patients showed ILD on HRCT. DLco, M-Borg, GERD-Q, and capillary density were significantly associated with the presence of ILD-SSc. A model including these variables had a coefficient of determination (R2) of 0.697. DLco had an AUC of 0.861 (p&lt;0.001) with a cut-off ≤72.3% (sensitivity 78.8%, specificity 91.1%, +LR 8.86). The m-Borg scale showed an AUC of 0.883 (p&lt;0.001) with a cut-off &gt;2 (sensitivity 84.8%, specificity 82.2%, +LR 4.77), GERD-Q had an AUC of 0.815 (p&lt;0.001) with a cut-off &gt;7 (sensitivity 72.7%, specificity 86.7%, +LR 5.45). The capillary density showed an AUC of 0.815 (p&lt;0.001) with a cut-off ≤4.78 (sensitivity 87.9%, specificity 68.9%, +LR 2.82). Based on the pre-test probability values, these four variables were applied to Fagan's nomogram to calculate the post-test probability of this association. Conclusions. Our study identified four associated clinical factors of ILD in SSc patients. Moreover, their inclusion in an algorithm for the post-test probability, tailored to the specific patients’ characteristics, significantly increases the ability to find out the presence of SSc-ILD.

The intrinsic non-linearity and complexity of suspended sediment dynamics, which are impacted by the geographical variability of basin parameters and temporal climatic patterns, make it difficult to estimate suspended sediment concentration (SSC) accurately in hydrological processes. Deep neural networks (DNNs), a cutting-edge modeling method that can capture the innate non-linearity in hydrological systems, have emerged as a solution to this problem. Using primary data on discharge, SSC, and turbidity, the long short-term memory method of DNNs was employed in this study to simulate the discharge-suspended sediment connection for the Esopus Creek, NY, USA as the first objective. To develop effective modeling strategies, multiple scenarios of feature selection, including combinations of discharge, turbidity and SSC for preceding days, were considered. Secondly, the variations in SSC and discharge between the three USGS gages along Esopus Creek that were upper stream, lower stream, and downstream, adjacent to the pourpoint were analyzed. Statistical metrics and scenarios of feature importance were used to evaluate the effectiveness of the DNN-based models. The study shows that among 24 DNN approaches feature selection is crucial in simulating the daily SSC, and discharge and presenting novel research directions for utilizing machine learning algorithms in water quality.

This paper proposes a solution for the development of microclimate monitoring for Low Voltage / High Voltage switchgear using the PRTG Internet of Things (IoT) platform. This IoT-based real time monitoring system can enable predictive maintenance to reduce the risk of electrical station malfunctions due to unfavorable environmental conditions. The combination of humidity and dust can lead to unplanned electrical discharges along the isolators inside a low or medium voltage electric table. If no predictive measures are taken, the situation may deteriorate and lead to significant damage inside and outside the switchgear cell. Thus, the mentioned situation can lead to unprogrammed maintenance interventions that can conduct to the change of the entire affected switchgear cell. Using a low-cost and efficient system, the climate conditions inside and outside the switchgear is monitored and transmitted remotely to a monitoring center. From the results obtained using a 365-day time interval, we can conclude that the proposed system is integrated successfully in the switchgear maintaining process, having as result the reducing of maintenance costs.

An automated discharge imaging system (ADIS), a non-intrusive and safe approach, was developed for measuring river flows during flash flood events. ADIS consists of dual cameras to capture complete surface images in the near and far fields. Surface velocities are accurately measured using the Large Scale Particle Image Velocimetry (LSPIV) technique. The stream discharges are then obtained from the depth-averaged velocity (based upon an empirical velocity-index relationship) and cross-section area. The ADIS was deployed at the Yu-Feng gauging station in Shimen Reservoir upper catchment, northern Taiwan. For a rigorous validation, surface velocity measurements were conducted using ADIS/LSPIV and other instruments. In terms of the averaged surface velocity, all measured results were in good agreement with small differences, i.e., 0.004 to 0.39 m/s and 0.023 to 0.345 m/s when compared to those from acoustic Doppler current profiler (ADCP) and surface velocity radar (SVR), respectively. The ADIS/LSPIV was further applied to measure surface velocities and discharges during typhoon events (i.e., Chan-Hom, Soudelor, Goni, and Dujuan) in 2015. The measured water level and surface velocity both showed rapid increases due to flash floods. The estimated discharges from ADIS/LSPIV and ADCP were compared, presenting good consistency with correlation coefficient R = 0.996 and normalized root mean square error NRMSE = 7.96%. The results of sensitivity analysis indicate that components till (τ) and roll (θ) of the camera are most sensitive parameter to affect the surface velocity using ADIS/LSPIV. Overall, the ADIS based upon LSPIV technique effectively measures surface velocities for reliable estimations of river discharges during typhoon events.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

Motivated by the way animals react in nature, we introduce a fully-connected neural-network model, which incorporates the external pattern presented to the system as a fundamental tool of the recognition process. In this new scenario, in the absence of this external field, memories are not attractors inside basins of attraction, as in usual attractor neural networks, although basins may be created according to the external pattern, thus allowing storing a much larger number of memories. The key point consists in calibrating the influence of the external pattern such as to cancel the noise generated by those memories not correlated with the external pattern.We illustrate how this proposal works by including this new contribution in the standard Hopfield model, showing a significant increase in its recognition capacity (typically by a factor $10^{2}$). As an additional feature of this model, we show its ability to react promptly to changes in the external environment, a crucial attribute of living beings. This procedure can be applied to a wide variety of neural-network models to increase considerably their recognition and reaction capabilities.

Propolis is a bee product widely used as a dietary supplement and included in sweets or baby foods due to its well-known antioxidant and nutritional properties that are directly correlated with its phenolic composition. For this reason, this study analysed the total contents of flavones and flavonols, flavanones and dihydroflavonols, and the antioxidant capacity by using the methods of ABTS and linoleic acid/β-carotene in 99 samples of propolis from Spain and Chile. A rapid method was developed for quantifying these parameters in raw propolis using near infrared (NIR) spectroscopy with an optical fibre probe of remote reflectance applied directly to the ground up sample. The models developed allow the determination of the total of flavones and flavonols (0-183 mg rutin/ g propolis), of the total of flavanones and dihydroflavonols (9-109 mg pinocembrin/ g propolis extract), and the antioxidant capacity by the ABTS method (0-3212 nmolesTrolox/ mg of propolis) and of linoleic acid/β-carotene (22-86% inhibition). The NIR spectroscopy models were applied in external validation to different samples of the calibration group, which led to the conclusion that the methods developed provide significantly identical data to the initial chemical data of reference.

An arc glow discharge device was used to prepare a helical carbon fiber skeleton with helical carbon fibers hooked to each other by spraying hydrogen and ethanol mixture onto the iron wire substrate through the discharge area, using anhydrous ethanol as carbon source. The various growth modes of carbon fiber during the formation of carbon fiber skeleton were investigated. A ring appearance that indicates a change in the direction of carbon fiber growth is observed. And double helical carbon fiber was constructed from single helical carbon fiber in two ways. A super-large carbon fiber with a diameter of about 13μm was observed, and it is speculated that this super-large carbon fiber is the backbone of the carbon fiber skeleton. The mechanical properties of carbon fiber skeleton are isotropic.

Electric Transformers make up some of the most critical components of a power system. Their reliable operation is critical for an efficient power grid as well as economic viability for the transformer operators and owners. Power transformers, like other High Voltage (HV) electrical equipment experience aging and insulation degradation due to chemical, mechanical and electrical forces during their operation. Partial Dischargers (PD) are localized electrical discharges that develop within insulation systems of HV electrical equipment such as transformers. In transformers, PD occurs in different forms and various locations and insulation both internal and external of the transformer. PD originates as small pulses but tends to increase in size and intensity which can result in complete insulation failure. Monitoring partial discharges has proven to provide valuable information on the state of the insulation systems of the power transformer, allowing transformer operators to make calculated decisions for the maintenance and life of plant plans. This systematic literature review aims to systematically examine the use of machine learning techniques in classifying PD in transformers to present a complete indicator to allow for future research in the field. The systematic review surveyed a total of 81 research literature published from 2010 to 2023 that fulfilled a specific methodology which was developed as part of this study. The results revealed that supervised learning has been the most widely used Artificial Intelligence (AI) algorithm utilized, primarily in the form of Support Vector Machine (SVM). Regarding PD, the survey revealed that most researchers tend to use numerous types of PD and compare them to one another. Furthermore, the use of artificial PD defect models to simulate the occurrence of PD is widely used versus the use of actual power transformers. Most of the literature tends to not specify the physical characteristics of PD, such as the magnitude of PD, PD inception voltage and PD extinction voltage.

Nanostructured transition metal nitrides (TMNs) have been considered a promising substitute for precious metal catalysts toward ORR due to their multi-electron orbitals, metallic properties, and low cost. To design TMNs catalysts with high catalytic activity toward ORR, the intrinsic features of the influencing factor on the catalytic activity toward ORR of nanostructured TMNs need to be investigated. In the paper, titanium nitride (TiN), zirconium nitride (ZrN), and hafnium nitride (HfN) nanoparticles (NPs) are high-efficiency and one-step synthesized by the direct current arc plasma. TiN, ZrN, and HfN NPs with an oxidation layer are applied as the catalysts of hybrid sodium-air batteries (HSABs). The effect of composition and structure attributes of TMNs on ORR catalysis is defined as follows. (ⅰ) Composition effect. With the increase of the oxygen content, the catalytic ORR capability of TMNs decreases progressively due to the reduction of oxygen adsorption capacity; (ⅱ) Structure effect. The redistribution of the density of states (DOS) of ZrN indicates higher ORR activity than TiN and HfN. HSABs with ZrN exhibit an excellent cyclic stability up to 137 cycles (about 140 h), an outstanding rate performance, and a specific capacity of 2817 mAh·g−1 at 1.0 mA·cm−2.

A highly-integrated experimental system for plasma decomposition of fuels was built. Experiments were conducted and confirmed that macromolecular chain hydrocarbons were cracked by large-gap dielectric barrier discharge under the excitation of a microsecond-pulse power supply. Alkanes and olefins with a C atom number smaller than 10 as well as hydrogen were found in the cracked products of n-decane (n-C10H22). The combination of preheating and plasma decomposition had strong selectivity for olefins. Under strong discharge conditions, micromolecular olefins were found in the products. Moreover, there was a general tendency that micromolecular olefins gradually accounted for higher percentage of products at higher temperature and discharge frequency.

Over recent years, the swine industry has witnessed the withdrawal of antibiotics and continuous regulation of zinc and copper oxides in the early-life nutrition of piglets. Due to this development, alternative ingredients or additives from plant sources have been tremendously explored. Therefore, this study's objective was to evaluate the effect of dietary supplementation with tannins on weaned piglets’ growth performance, serum antioxidant capacity, and immune status using a meta-analysis approach. With only the inclusion of non-challenged weaned piglets, a total of 16 studies with parameters of interest were deemed eligible after a two-step screening process following a comprehensive literature search in the scientific databases of Web of Science, Scopus, ScienceDirect, PubMed, and Google Scholar. Two main categories of data, including the study’s characteristics and response variables (growth performance, serum antioxidant, and immune indices), were extracted. Applying the random-effects models, Hedges’ g effect size of supplementation with tannins was calculated using the R software to determine the standardized mean difference (SMD) at a 95% confidence interval. Sub-group analysis and meta-regression further explored heterogeneity (PSMD 0.05, I2 50%, n ≥10). Supplementation with tannin reduced average daily gain (p = 0.20) and feed conversion ratio (p 0.01); however, it increased average daily feed intake (p = 0.07) and final body weight (p 0.01). Meta-regression models indicated that tannin dosage and supplementation duration were directly associated with tannins' effectiveness on productive performance. In the serum, the concentration of glutathione peroxidase, superoxide dismutase, and total antioxidant capacity were elevated (p 0.01) in response to tannins supplementation, while malondialdehydes was reduced (p 0.01). Likewise, decreased immunoglobin A (p = 0.47) and increased immunoglobin M and G levels (p 0.01) were detected. In conclusion, dietary supplementation with tannins, particularly with chestnut and grape seed proanthocyanidins, increases the productivity of weaned piglets. At the same time, it is a possible nutritional strategy to mitigate oxidative stress and stimulate gut health. Thus, supplementing chestnut and grape seed proanthocyanidin tannins in the early phase of swine production could be used to alleviate the incidence of diarrhea.

Quercetin is a flavonoid with a low molecular weight that belongs to the human diet's phenolic phytochemicals and non-energy constituents. Quercetin has a potent antioxidant capacity, being able to capture Reactive Oxygen Species (ROS), reactive nitro-gen species (RNS), and Reactive Chlorine Species (ROC), which act as reducing agents by chelating transition metal ions. Its structure has five functional hydroxyl groups, which work as electron donors and are responsible for capturing free radicals. In addition to its antioxidant capacity, it was described different pharmacological properties of Quercetin, such as carcinostatic properties, antiviral, antihypertensive, anti-inflammatory, protection of Low-Density Lipoprotein (LDL) oxidation, and inhibi-tion of angiogenesis are developed in this review.

This paper has two objectives: the first, to analyze the mediating effect of teacher empowerment between innovation culture and innovation capacity, and between inclusive leadership and innovation capacity; the second, to analyze the moderating effects of the school context on the innovation capacity. Data were collected in a representative sample of secondary schools in Valencia, Spain. The research model adopted is structural equation modeling, using the partial least squares (PLS) technique. The model has confirmed that teacher empowerment mediates between innovation culture and innovation capacity and between inclusive leadership and the innovation capacity. It is found that the educational context does not moderate the relationships in the proposed analysis model. This paper emphasizes the role of teacher empowerment in educational innovation and extends the knowledge of culture and leadership in the school organization.

Climate change is an important threat to orchard production at Mediterranean basin. Diversification seems to be implemented at a farm level as an important strategy to face these challenges. This paper aims to analyse farmer’s perceptions on crop diversification as a way to enhance farm’s adaptive capacity in a context of current and future climate changes impacts. Our case study is focused in orchards growers from French department of Vaucluse recently diversifying their activities through pistachio (Pistacia vera L.). We did in-depth semi-structured farmers’ interviews in 2021. The results show that diversification is supposed to enhance 3 main components of farms adaptative capacity: (1) strengthening robustness through improvement of buffering capacities to climate impacts (trough robust and adapted plants), economic uncertainties (by exploring local/niche markets) and labour scarcity (by lowering workforce requirements and mechanization); (2) Learning by experimenting, monitoring and exchanging with pairs and advisors (3) Cope with change related with societal demands and helps to increase personal satisfaction. Finally, promote farm’s diversification can contribute to enhance farm’s adaptive capacity under climate change impacts.

The study evaluated potassium peroxymonosulfate (PPMS) efficacy against rifampicin-resistant Salmonella Infantis (rif-SI), Escherichia coli (E. coli), Salmonella Infantis (SI), Newcastle disease virus (NDV) and avian influenza virus (AIV). The assessment encompassed varied concentrations, organic material conditions, and exposure durations to comprehensively evaluate PPMS efficacy. Moreover, PPMS’s efficacy was tested on diverse carrier surfaces and clothing to evaluate its bactericidal and virucidal potential. At the recommended concentrations (1X), PPMS effectively inactivated all pathogens within 5 sec, except for NDV, which required 30 sec in the presence of organic materials. At 0.5X, PPMS successfully inactivated E. coli, AIV and NDV within 5 sec in the absence of organic material. However, rif-SI and SI necessitated 30 sec for inactivation. Most pathogens were inactivated within 30 sec, with the exception for AIV, which was inactivated within 5 sec. PPMS effectively eliminated rif-SI on all carriers within 30 sec. Moreover, at both concentrations, PPMS successfully inactivated AIV on all carriers within 30 sec, except on stainless steel at 0.5X. Furthermore, PPMS at both concentrations required 5 and 30 sec, respectively, to inactivate AIV on the rayon sheet. Therefore, due to its demonstrated efficacy against a wide range of pathogens across diverse surfaces, PPMS emerges as a crucial alternative disinfectant significantly enhancing biosecurity on and around chicken farms. found in and around animal farms, slaughterhouses, and hospitals.

Temperature differences between the atmosphere and river water allow rivers to be used as a hydrothermal energy source. The river-water heat pump system is a relatively non-invasive renewable energy source; however, effluent discharged from the heat pump can cause downstream temperature changes which may impact sensitive fluvial ecosystems. In this study, the water temperature recovery distance of the effluent was estimated for a river section in the Han River Basin, Korea, using the heat transfer equation and the Environmental Fluid Dynamic Code (EFDC) model. Results showed that, compared to the EFDC model, the heat transfer equation tended to overestimate the water temperature recovery distance due to its simplified assumptions. The water temperature recovery distance could also be used as an objective indicator to decide the reuse of downstream river water. Furthermore, as the river system was found to support an endangered fish species that is sensitive to water environment changes, care should be taken to exclude the habitats of protected species affected by water temperatures within water temperature recovery distance.

Microbiome research has gained considerable interest due to the emerging evidence of its impact on human and animal health. Similar to higher organisms, the gut-associated microbiota of mosquitoes affect host fitness and other phenotypes. It is now well established that microbes can alter pathogen transmission in mosquitoes, either positively or negatively, and avenues are being explored to exploit microbes for vector control. However, less attention has been paid to how microbiota affect phenotypes that impact vectorial capacity. Several mosquito and pathogen components, such as vector density, biting rate, survival, vector competence and pathogen extrinsic incubation period all influence pathogen transmission. Interestingly, the mosquito gut-associated microbes can impact each of these components, and therefore ultimately modulate vectorial capacity. Promisingly, this expands the options available to exploit microbes for vector control by also targeting parameters that affect vectorial capacity. However, there are still many knowledge gaps in the biology of the mosquito – microbe symbiosis that need to be addressed in order to understand these interactions more thoroughly and exploit them efficiently. Here, we review current evidence of the impacts of the microbiome on aspects of vectorial capacity highlighting opportunities for novel vector control strategies and areas where further studies are required.

An increasing body of evidence shows that seaweeds, including kelp, can be used as a tool to neutralize or remove excess nutrients and metals from the water column. Here we report on a preliminary field assessment showing potential nutrient and carbon removal differences by sugar kelp and ribbon kelp grown in common gardens. Seawater and tissue samples were collected systematically from two farms in Alaska. Results show differences between % N and % C content between ribbon kelp (Alaria marginata) and sugar kelp (Saccharina latissima). Results also show that tissue nitrogen in ribbon kelp varies sharply due to nitrogen availability in the water column. In contrast, the percentage of tissue N in sugar kelp remains comparatively stable. Our outcomes provide insight into potential differences in nutrient removal and harvest timing for different kelp species.

Considerable amounts of agro-industrial by-products are discarded or burnt as fuel every year. However, they can be utilized as a valuable source of fiber, phenolics and other useful compounds such as antioxidants. The profile of beneficial compounds can be affected by genotype, locality, orchard management and productive season, adding or decreasing the bioactive potential of by-products. In this study, hazelnut (Corylus avellana L.) and walnut (Juglans regia L.) nutshells were investigated for their fiber content and antioxidant capacity as valorized by-products for the industry. Determinations (ORAC, TPC and color asses) were performed in hazelnut and walnut orchards located in Southern Chile during three consecutive seasons (2020/21; 2021/22 and 2022/23). Analyses of oxygen radical absorbance capacity (ORAC) in nutshells showed the highest ORAC from both species in the season 2020/21 (3217 µmol TE g1DW for hazelnut shells and 4663 µmol TE g DW1 for walnut shells), while variability in the consecutive seasons was lower for hazelnut than in walnut. Total phenolic content in hazelnut shells was positively correlated with L* (R: 0.883) and E (R: 0.924) during 2020/21 season, also with L* for 2022/23 (R: 0.907). While ORAC was negatively correlated with L* (R: 0.922) in 2021/22. In addition, morphological and structural features of both nutshells examined by Scavenging Electron Microscopy (VP-SEM) and Confocal Scavenging Laser Microscopy (CSLM) revealed differential tissue distribution and accumulation patterns of both cellulose and lignin. On the other hand, photo-colorimetric values were determined for both shells and corresponding seasons, and non-significative differences were found both shells and among seasons Finally, these results provide insight into the physicochemical characteristics of two shell types which should be considered together with antioxidant capacity in their valorization as a residual material.

This study investigated the effects of dietary garlic powder and fermented garlic powder supplementation at 1% and 2% levels on growth performance, digestive tract efficacy, blood biochemistry, immunity, and antioxidant status of Liza ramada (n=225 fish; 86.00±0.42 g) over a 60-day period. Fish fed diets supplemented with both forms of garlic at both levels exhibited significantly improved final body weight, weight gain, specific growth rate, and feed conversion ratio compared to the control group. Digestive enzyme activities (amylase, lipase, and protease) were significantly enhanced in all supplemented groups. Blood biochemical analysis revealed reduced glucose levels and increased total protein in garlic-supplemented groups, with no adverse effects on liver or kidney function markers. Immune parameters, including lysozyme activity, bactericidal activity against Streptococcus agalactiae, alternative complement pathway (ACP), and, respiratory burst (NBT) were significantly enhanced in garlic-supplemented groups, with fermented garlic showing more pronounced effects. Antioxidant enzyme activities (SOD, CAT, and GPx) were also significantly increased in all supplemented groups, particularly in those fed fermented garlic. No significant differences in survival rates were observed among treatments. The results suggest that both garlic powder and fermented garlic powder supplementation, especially at the 2% level, can effectively improve growth, feed utilization, immune function, and antioxidant status in L. ramada. Fermented garlic generally demonstrated superior effects, indicating its potential as a beneficial feed additive in aquaculture. Based on these findings, it is recommended to incorporate fermented garlic powder at a 2% level in L. ramada diets to optimize growth performance and health status. Further research is warranted to investigate the long-term effects and cost-effectiveness of this supplementation strategy in commercial aquaculture settings.

With the increasing demand for precise condition monitoring and diagnosis of gas-insulated switchgears (GIS), it has become a challenge to improve the detection sensitivity of partial discharge (PD) induced in the GIS spacer. This paper deals with the elimination of the capacitive component from the phase resolved partial discharge (PRPD) signal generated in GIS spacer based on the discrete wavelet transform. Three types of typical insulation defects were simulated using PD cells. The single PD pulses were detected and were further used to determine the optimal mother wavelet. As a result, the bior6.8 was selected to decompose the PD signal into 8 levels and the signal energy at each level was calculated. The decomposed components related with capacitive disturbance were discarded whereas those associated with PD were de-noised by a threshold and a thresholding function. Finally, the PRPD signals were reconstructed using the de-noised components.

The operation of transformers suffers from natural or man-made disasters, subjecting the equipment to prolonged exposure to temperature, lightning strikes, transient over-voltages, and over-current, gradually producing insulation aging phenomenon, which results in partial discharges within the transformer. Without dealing with it beforehand properly, it may lead to insulation breakdown. Nowadays, with the mature development of microchip control technology and wireless communication technology, which is helpful for realizing the research for online real-time and long-term monitoring capabilities for power equipment. A transformer operating condition monitoring and diagnostic system that can rapidly and effectively prevent the breakdown of transformer insulation, which can impact the overall power supply system is developed in this paper. The system is divided into two parts based on its function. The first part is the operating condition monitoring and real-time alert unit for the transformer, primarily composed of an embedded computing module, a sensor module, and a transmission module. Its work content is to capture real-time online partial discharge ultrasonic signals and high frequency current comparator pulse signals, and analyze and determine the condition of the internal insulation and operational status whether it is fault or not. The second part is the central control unit, consisting mainly of an industrial computer and a transmission module. Its work content is to store the ultrasonic and high frequency current comparator pulse signals from the transformer operation monitoring and real-time alert unit. It uses the software to eliminate signal noise and interference, and then utilizes artificial neural networks to identify the type of fault. In this paper, the research for the phenomenon of insulation degradation in transformer equipment aims to establish aging trend profiles through the dual malfunctioning alert and aging process analysis, as well as the long-term measurement of ultrasonic signals from partial discharges and high-frequency current comparator pulse signals. This approach provides crucial reference data and a foundation for disposable on-site measurement, assessing the phenomenon of insulation aging stages, defects and damage of the transformers effectively. It allows for timely replacement or maintenance in advance, achieving the prevention of malfunctioning and predictive diagnosis of aging.

The dynamics of suspended sediment involves inherent non-linearity and complexity as a result of the presence of both spatial variability of the basin characteristics and temporal climatic patterns. As a result of this complexity, the conventional sediment rating curve (SRC) and other empirical methods produce inaccurate predictions. Deep neural networks (DNNs) have emerged as one of the advanced modeling techniques capable of addressing inherent non-linearity in hydrological processes over the last few decades. DNN algorithms are used to perform predictive analysis and investigate the interdependencies among the most pivotal water quantity and quality parameters i.e., discharge, suspended sediment concentration (SSC), and turbidity. In this study, the Long short-term memory (LSTM) algorithm of DNNs is used to model the discharge-suspended sediment relationship for the Stony Clove Creek. The simulations were run using primary data on discharge, SSC and turbidity. For the development of the DNN models and examining the effects of input vectors, combinations of different input vectors (namely discharge, and SSC) for the current and previous days are considered. Furthermore, a suitable modelling approach with an appropriate model input structure is suggested based on model performance indices for the training and testing phases. The performance of developed models is assessed using statistical indices such as root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). Statistically, the performance of DNN-based models in simulating the daily SSC performed well with observed sediment concentration series data. The study demonstrates the suitability of the DNN approach for simulation and estimation of daily SSC, opening up new research avenues for applying hybrid soft computing models in hydrology.

Capacitor banks are widely used in current electrical transmission systems in order to improve power quality and increase efficiency. Utilizing high voltage components such as, shunt capacitors in the power grid imposes new challenges to the system which are required to be addressed. One of these challenges is corona discharges that can have negative impacts on capacitor banks such as power loss, insulator erosion followed by equipment failure, and radio interference. Although previous studies have almost exclusively focused on optimization of corona suppression rings for transformers and transmission lines, no specific studies have conducted regarding high voltage capacitor banks. This paper presents a novel study concerning verification and development of corona discharge suppression models on AC and DC capacitor banks with two different voltage levels. The employed method is based on the Maxwell’s equations and finite element method (FEM) which is implemented with the help of COMSOL Multiphysics© software. Results have verified the necessity of suppression methods as well as the efficiency of proposed solutions. Corona inception voltage levels are identified and effective factors on its appearance are reviewed. Analyses of proposed solutions have shown significant improvements in optimization of corona suppression methods as well as enhancement of maintenance maneuverability.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

The prevention, mitigation and treatment of movement impairments, ideally, requires early diagnosis or identification. As the human movement system has physiological and functional redundancy, movement limitations do not promptly arise at the onset of physical decline. A such, prediction of movement limitations is complex: it is unclear how much decline can be tolerated before movement limitations start. Currently, the term ‘homeostatic reserve’ or ‘physiological reserve’ is used to refer to the redundancy of the human biological system, but these terms do not describe the redundancy in the muscle architecture of the human body. The result of functional redundancy is compensation. Although compensation is an early predictor of movement limitations, clear definitions are lacking and the topic is underexposed in literature. The aim of this article is to provide a definition of compensation and emphasize its importance. Compensation is defined as an alteration in the movement trajectory and/or altering muscle recruitment to complete a movement task. Compensation for capacity is the result of a lack in neuromusculoskeletal reserve, where reserve is defined as the difference between the capacity (physiological abilities of the neuromusculoskeletal system) and the task demand. Compensation for movement objectives is a result of a shift in weighting of movement objectives, reflecting changing priorities. Studying compensation in biomechanics requires altered protocols in experimental set-ups, musculoskeletal models that are not reliant on prescribed movement, and inclusion of alternative movement objectives in optimal control theory.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of radio-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes were investigated. The main gas-phase and solid products of plasma-chemical transformations were determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems was carried out. It is shown that under the implemented experimental conditions, equilibrium components of the products are established. The detected spectra of chemical activity were studied, which gave reason to assume that the molecular mechanism of the hydrogen reduction process is the main one. The impurity composition of gas-phase and solid reaction products was investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, was shown.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

This study aims to assess trends and significant changes in precipitation and river flow in the Senegal River basin and its upper basin over the period 1982-2021. Eight hydroclimate indicators, namely maximum river discharge (QMAX), standardized flow index, mean daily rainfall intensity index (SDII), maximum 5-day consecutive precipitation (RX5DAY), annual precipitation exceeding the 95th percentile (R95p), annual precipitation exceeding the 99th percentile (R99P), annual flows exceeding the 95th percentile (Q95p), and annual flows exceeding the 99th percentile (Q95p) were considered.. The modified Mann-Kendall test (MMK) was used to analyze trends in extremes while standard normal homogeneity and Pettit’s tests were employed to detect potential breakpoints in these trends. The results indicated an irregular precipitation pattern, with high values of extreme precipitation indices (R95p, R99p, SDII, and RX5DAY) in the southern part, while the northern part exhibits lower values. Inter-annual analysis revealed a significant increase in extreme precipitation events between 1982 and 2021, with a notable breakpoint around the years 2006 and 2007. This breakpoint marks a transition to a much wetter period starting from 2008. Regarding extreme flows, a significant increase was observed between 1982 and 2021. This study provides insights into past hydrological extremes in the study area and can serve as a basis for future research in this field.

The correct classification of defects originating from partial discharges (PD) in medium-voltage (MV) switchgears with air insulation (AIS) remains a challenging research topic for scientists worldwide. In this article, the authors simulated four possible defects occurring in the power industry, including one that is a simultaneous combination of two commonly ones. In addition, the correctness of the algorithm was checked by adding a classification class without any fault. The measurement signals were recorded with TEV sensors. The effectiveness of various hy-brid-connected neural networks was tested and discussed: GoogleNet and SqueezeNet based on spectrograms, SAE with FNN, 2D-CNN with LSTM, and hybrid AE combined with CNN and LSTM. The highest effectiveness – approximately 97% – was demonstrated by the GoogleNet and SqueezeNet networks. The research results are expected to form the basis for the development of a universal and wireless capacitive sensor for monitoring the level of PD in switchgears.

Photodynamic therapy (PDT) has garnered significant attention in the fields of cancer treatment and drug-resistant bacteria eradication due to its non-invasive nature and spatiotemporal controllability. Iridium complexes have captivated researchers owing to their tunable structure, exceptional optical properties, and substantial Stokes displacement. However, most of these complexes suffer from aggregation-induced quenching, leading to diminished luminous efficiency. In contrast to conventional photosensitizers, photosensitizers exhibiting aggregation-induced luminescence (AIE) properties retain the ability to generate a large number of reactive oxygen species when aggregated. To overcome these limitations, we designed and synthesized a novel iridium complex named Ir-TPA in this study. It incorporates quinoline triphenylamine cyclomethylated ligands that confer AIE characteristics for Ir-TPA. We systematically investigated the photophysical properties, AIE behavior, spectral features, and reactive oxygen generation capacity of Ir-TPA. The results demonstrate that Ir-TPA exhibits excellent optical properties with pronounced AIE phenomenon and robust capability for producing singlet oxygen species. This work not only introduces a new class of metal iridium complex photosensitizer with AIE attributes but also holds promise for achieving remarkable photodynamic therapeutic effects in future cellular experiments and biological studies.

eHealth applications are an essential component in achieving Universal Health Coverage. (1) Background: The lack of skilled healthcare personnel has hindered successful integration and use, especially in developing and low and middle-income countries. (2) Methods: A descriptive study was conducted using an online survey to collect quantitative data from 37 organizations to address this issue. (3) Results: The findings showed that there are limited training opportunities available for policymakers and eHealth specialists. Additionally, obstacles such as insufficient funds, inadequate infrastructure, poor leadership, and governance were identified and found to be context specific. To mitigate these challenges, the study proposed continuous in-service training, the implementation of computer-based systems, and the integration of academic modules. The importance of strong eHealth policies and committed leaders was also emphasized. (4) Conclusions: The results of this study support previous research and emphasize the importance of implementing practical and uncomplicated solutions to overcome eHealth barriers to capacity building in low- and middle-income countries. It is essential to recognize that the data collected for this study only pertains to BETTEReHEALTH.

Soy isoflavones are considered important sources of bioactive compounds, but they are poorly absorbable, due to their large hydrophilic structures. Some biotransformation strategies have been used to convert the glycosidic form into aglycones, making them available for absorption. This study evaluated the potential of enzymatic and/or microbial fermentation bioprocesses in soymilk extract before and after gastrointestinal in vitro digestion. Commercial β-glucosidase and mix of commercial probiotics containing Lactobacillus acidophilus, L. casei, Lactococcus lactis, Bifidobacterium bifidum e B. lactis were used to biotransform soymilk extract. Isoflavone profile was quantified by HPLC-DAD, total phenolic content by Folin–Ciocalteu test, and antioxidant capacity by ORAC and FRAP. Soymilk enzymatically treated (ET) followed by microbial fermentation (ET+F) resulted in the conversion of glycosylated isoflavones (6-fold lower than control for daidzin and 2-fold for genistin) to aglycones (18-fold greater than control for dadzein and genistein), besides to increase the total phenolic content (3.48 for control and 4.48 mg/ml ET+F) and to improve antioxidant capacity represented by the ORAC (120 for control and 151 mg/ml ET+F) and by the FRAP (285 for control and 317 µl/ml for ET+F) before in vitro digestion. Further, the digested ET+F samples resulted a higher content of genistein (2-fold higher than control) also an increase in the total phenolic content (2.81 for control and 4.03 mg/ml for ET+F) and antioxidant capacity by ORAC were greater compared to undigested samples. In addition, the microbial fermentation process isolated also resulted in the positive effects, but de combination of ET followed by F presented a synergistic effect, suggesting the greater potential for both bioprocesses to contribute to functional and nutritional properties on fermented soy-based products.

The coal mine underground reservoir is an appropriate solution between coal mining and groundwater resource protection and utilization. By calculating the storage capacity of a groundwater reservoir, the storage coefficient has been proved to be always an empirical value. Based on the mathematical derivation of the vertical fracture area ratio and the horizontal fracture area rate of the collapse zone and the fissure zone in the goaf area of the coal seam, the mathematical models of tem are derived, and the model for calculating the water storage coefficient is derived. The water storage coefficient derived from the theoretical model had more basis and more advanced than the traditional empirical value. By using this method, the practical calculation of No.1 underground reservoir of the DaLliuta Coalmine in Shenhua Shendong, has got a perfect matching with the actual groundwater storage capacity.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

Water pollution is the main cause of global ecological degradation and seriously affects people's water supply. In order to respond to the water environmental protection policy and provide management departments with a basis for refining water quality, this paper used the environmental Gini coefficient (EGC) method based on four indicators such as water environmental capacity, population, land area, and gross domestic production (GDP) to represent social factors, economic factors, and environmental factors, respectively. After the optimization, for COD, the EGC based on the land area was 0.30, EGC based on population was 0.21, EGC based on environment capacity was 0.02, and the EGC based on GDP was 0.45, and the sum of EGC was 0.962. From this result, we observed that the change in the Gini coefficient of each indicator was not very big. Hence, the most significant change in the Gini coefficient was that of GDP, with a higher rate than other criteria. Then, the COD, AND, and TP discharge allocation model was constructed to obtain the total allocated discharge permit in Lushui Basin. The results found that the total discharge permit allocation of COD, AN, and TP to the Lushui basin were 51483.304 tons/year, 843.119 tons/year, and 340.926 tons/year, respectively. Based on the GIS spatial analysis technology, the distribution of unfair factors that cause pollution inequity was investigated. Finally, the reduction measures were proposed to implement environmental supervision and strengthen water environment management strictly.

Intensive care unit discharge is an important transition which impacts on patient wellbeing. Nurses can play an essential role in this scenario, potentiating patient empowerment. A systematic review was conducted using the Preferred Reporting Items for Systematic Reviews and Meta-Analyses: the PRISMA Statement. Embase, PubMed/MEDLINE, CINAHL, and Cochrane Central Register of Controlled Trials (CENTRAL) databases were evaluated in May 2021. Two independent reviewers analyzed the studies, extracted the data, and assessed the quality of evidence. Quality of the studies included was assessed using the Cochrane risk-of-bias tool. Of the 273 articles initially identified, eight randomized controlled trials reported nursing interventions mainly focused on patients’ ICU discharge preparation through information and education. The creation of ICU Nurse-Led and nurses’ involvement in critical care multidisciplinary teams also aimed to support patients during ICU discharge. This systematic review provides an update on clinical practice aimed at improving the patient experience during ICU discharge. The main nursing interventions were based on information and education, as well as the development of new nursing roles. Understanding transitional needs and patient empowerment are key to making the transition easier.

The article contains the results of experimental studies for a multi-opening orifice with substitute constriction factor of β = 0.5 (m = 0.25), mounted in a DN50 hydraulic measuring flume. Flow measurements were taken for a progressing turbulent flow within Reynolds numbers (Re = 4700...19500). Based on experimental data, flow characteristics as well as discharge coefficient C characteristics were determined. Relative expanded uncertainty of determining a discharge coefficient C was estimated within the changes of volume flow qv from 0.35 dm3/s to 0.68 dm3/s. The value does not exceed 1.25% within the changes of Reynolds numbers 9800 ≤ Re ≤ 19500.

Passive plasma spectroscopy is a well-established non-intrusive diagnostic technique. Depending on the emitter and its environment which determine the dominant interactions and effects governing emission line shapes, passive spectroscopy allows the determination of electron densities, emitter and perturber temperatures as well as other quantities like abundances. However, using spectroscopy needs appropriate line shape codes retaining all the physical effects governing the emission line profiles. This requires for line shape code developers to continuously correct or improve them to increase their accuracy when applied for diagnostics. This is exactly the aim expected from code-code and code-data comparisons. In this context, the He I 492 nm emitted in a helium corona discharge at room temperature represents an ideal case since its profile results from several broadening mechanisms: Stark, Doppler, resonance and van der Waals. The importance of each broadening mechanism depends on the plasma parameters. Here the profiles of the He I 492 nm in a helium plasma computed by various codes are compared for a selected set of plasma parameters. In addition, preliminary results related to plasma parameter determination using experimental spectra from a helium corona discharge at low pressure 1- 2 bars, are presented.

Nowadays, there is extensive production and use of plastic materials for different industrial activities. These plastics, either from their primary production sources or through degradation processes of the plastics themselves, can contaminate the ecosystem with micro and nanoplastics. Once in the aquatic environment, these microplastics can be the basis for the adsorption of chemical pollutants, favoring that these chemical pollutants disperse more quickly in the environment and can affect living beings. Due to the lack of information on adsorption, three machine learning models (random forest, support vector machine, and artificial neural network) to predict different microplastic/water partition coefficients (log Kd) were developed using two different approximations (based on the number of input variables). The best-selected machine learning models present, in general, correlation coefficients upper than 0.92 in the query phase, which indicate that these type of models could be used for a rapid estimation of the absorption of organic contaminants on microplastics.

One of the mechanisms used in the management and cure of atherosclerosis is reverse cholesterol transfer (RCT), which plays a vital role in the export of cholesterol from peripheral cells. Cholesterol efflux from macrophages in the subintima of the vessel wall is a critical part of RCT. ATP-binding cassette transporter A1 (ABCA1) and ATP-binding cassette transporter G1 (ABCG1) are involved in the transfer of cholesterol from arterial macrophages to extracellular high-density lipoprotein cholesterol (HDL). The HDL then transports esterified cholesterol to the liver for elimination. An important factor in the reverse cholesterol transport and excretion of extracellular cholesterol is HDL. Atherogenesis can be prevented by altering the processes of RCT and cholesterol efflux, and this might lead to novel treatment options for cardiovascular disease. Research of novel modifying variables for RCT and cholesterol efflux is necessary. A better understanding of RCT's molecular processes has been gained via research, allowing for the creation of new treatments that make use of RCT's potential for pharmacological improvement. The purpose of this review is to provoke discussion on the potential impact of selected flavonoids on cholesterol efflux on the progression of atherosclerosis (Fig. 1.).

Water is essential for living organisms. The increase in world population, global climate change and rapid growth in industrialization and urbanization have brought with them water issues around the world in recent years. Not only should existing water resources be used reasonably and efficiently but alternative water resources should also be explored and secured. Rainwater harvesting, which is one of the alternative water resources, can provide economic and environmental solutions. For rainwater harvesting, the size of reservoirs in which rainwater captured from roof catchments is stored should be determined. Determining the optimum tank capacity depending on precipitation and consumption rates allows us to make maximum use of rainwater tanks. The aim of this study is to determine the optimum tank capacity for the storage of rainwater captured from roof catchments in order to meet the water demand for agricultural production. Precipitation data were collected from the city of Isparta and its districts. Rainwater tank capacity was determined using the Rippl, residual mass curve, minimum flow and particle swarm optimization methods. Storage capacities varying according to roof areas and consumption rates are shown in a graph. Results show that particle swarm optimization is the best method.

A statistical analysis of semantic memory should reflect the complex, multifactorial structure of the relations among its items. Still, a dominant paradigm in the study of semantic memory has been the idea that the mental representation of concepts is structured along a simple branching tree spanned by superordinate and subordinate categories. We propose a generative model of item representation with correlations that overcomes the limitations of a tree structure. The items are generated through "factors" that represent semantic features or real-world attributes. The correlation between items has its source in the extent to which items share such factors and the strength of such factors: if many factors are balanced, correlations are overall low; whereas if a few factors dominate, they become strong. Our model allows for correlations that are neither trivial nor hierarchical, but may reproduce the general spectrum of correlations present in a data-set of nouns. We provide an estimate of the number of concepts that can be stored and retrieved by a large-scale cortical network, the Potts network, which is perhaps approximately 10⁷ with human cortical parameters. When this storage capacity is exceeded, however, retrieval fails completely only for balanced factors; above a critical degree of imbalance, a phase transition leads to a regime where the network still extracts considerable information about the cued item, even if not recovering its detailed representation: partial categorization seems to emerge spontaneously as a consequence of the dominance of particular factors, rather than being imposed ad hoc. We argue this to be a relevant model of semantic memory resilience in Tulving’s remember/know paradigms.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

The availability of current land cover and land use (LCLU) information for monitoring the status of land resources has considerable value in ensuring sustainable land use planning. Similarly, the need to provide updated information on the extent of LCLU change in West Africa has become apparent, given the increasing demand for land resources driven by the rapid population growth in the sub-region. SERVIR West Africa, a regional consortium jointly supported by USAID and NASA to foster the use of geospatial and earth observation data and science for decision-making on critical environmental and food security challenges, in collaboration with the Food and Agriculture Organization of the United Nations (FAO), is building technical capacity in the sub-region to develop and implement harmonized regional land cover classification system for LULC change monitoring in West Africa, based on the Land Cover Meta Language (LCML-ISO 19144-2). This article focuses on the process, potential opportunities, outputs of this collaboration, exemplary use cases, and recommendations for the next steps.

Alum sludge, an inevitable by-product from the water purification process, which had been applied as substrates in some constructed wetlands with good performance, especially for phosphorus (P) adsorption. The raw alum sludge is like clay lump with irregular shape and has a leaching concern used in the water. For a better reuse, herein, sludge was fired to produce alum sludge ceramsite (ASC) with a uniform spherical shape via four-step process of kneading sludge ball, air drying, preheating at 400°C for 10 min and firing at 600℃ for 5 min. Thereafter the physicochemical properties and P adsorption ability of ceramsite were investigated. Through XRD and FT-IR tests, there was no obvious difference between ASC and air-dried alum sludge ball (adASB) on the phase structure, but a certain amount of Al-OH group loss on the surface of ASC. The structure of ASC was still amorphous as same as adASB, while ASC possessed more micropore structure and bigger specific surface area than those of adASB. Adsorption experiments showed the P adsorption behaviors of ASC and adASB were much similar, and their adsorption kinetics all accorded with the two-step adsorption kinetics rate equation and pseudo-second-order kinetics equation. The maximum adsorption capacities of ASC and adASB fitted by Langmuir model were 1.66 mg/g and 1.89 mg/g respectively. It should be pointed that, compared with other adsorbents, ASC produced in this study still had a higher ability to adsorb P. Therefore, ASC should have a great application potential for P removal in the wastewater treatment in China.