The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In small data set learning, obtaining a large number of training samples from the source class for transfer learning is a challenge for fine-grained visual classification. Based on the fact that fine-grained concepts can be learned with very few samples, we use very few labeled samples (for example, three) in each category. However, due to the difficulty in distinguishing the subtle differences between fine-grained images, we propose a local structure information extraction method of SDFGVC based on spatial frequency features. The proposed learning module enhances the ability of the network to find significant regions and shows excellent performance in experiments on six datasets.

A well known technique to enhance the signal to noise ratio (SNR) of repetitive signals is to average them. The coherent parts of the signal add up constructively while the incoherent parts are averaged out. The prerequisite is that the signals are acquired under conditions of high repeatability, i.e.\ the signals must be sufficiently similar. In the present technical note we describe an efficient method for maintaining signal similarity by ensuring spatial and temporal proximity of laser waveform signals obtained by a sensor operated from an airborne platform. The method makes use of a few auxiliary parameters such as laser pulse repetition rate, mirror rotation rate, platform altitude, and flight speed. The method can be extended to be operated in real time.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

The accurate assessment of wound size is a critical step in advanced wound care management. This study aims to introduce and validate a Light Detection and Ranging (LiDAR) technique for measuring wound size. Twenty-eight wounds treated from December 2022 to April 2023 at the Chunganam National University Hospital were analyzed. All wounds were measured using three techniques; conventional ruler methods, the LiDAR technique, and ImageJ analysis. Correlation analysis, linear regression, and Bland-Altman plot analysis were conducted to validate the accuracy of the newly introduced method. The measurement results (Mean ± Standard deviation) obtained using the Ruler method, LiDAR technique, and ImageJ analysis were 112.99 ± 110.07 cm², 73.59 ± 72.97 cm², and 74.29 ± 72.15 cm², respectively. The Pearson correlation coefficient was higher in the LiDAR application (0.995) than the conventional ruler methods (Mean difference; -5.0000 cm2), as was the degree of agreement (Mean difference; 38.6933 cm2). Wound size measurement using LiDAR is a simple and reliable method that allows practitioners to conveniently assess wounds with a flattened and irregular shape. However, non-flattened wounds cannot be assessed owing to the technical limitations of LiDAR.

In higher education, the cultivation of research competency is pivotal for students’ critical thinking development and their subsequent transition into the professional workforce. While statistics plays a fundamental role in supporting the completion of a research project, it is often perceived as challenging, particularly by students in majors outside mathematics or statistics. The connection between students’ statistical proficiency and their research competency remains unexplored despite its significance. To address this gap, we utilized the supervised machine learning approach to predict students’ research competency, as represented by their performance in a research methods class, with predictors of students’ proficiency in statistical topics. Predictors relating to students’ learning behavior in a statistics course such as assignment completion and academic dishonesty are also included as auxiliary variables. Results indicate that the three primary categories of statistical skills—namely, understanding of statistical concepts, proficiency in selecting appropriate statistical methods, and statistics interpretation skills— can be used to predict students’ research competency, as demonstrated by their final course scores and letter grades. This study advocates for strategic emphasis on the identified influential topics to enhance efficiency in developing students’ research competency. Findings could inform instructors in adopting a strategic approach to teaching the statistical component of research for enhanced efficiency.

For our research on droplet deformation and breakup in scaled high-pressure homogenizing units we developed a pressure stable inline droplet generator. It consists of an optically accessible flow channel with a combination of stainless steel and glass capillaries and a 3D printed orifice. The droplet size is determined online by live image analysis. The influence of the orifice diameter, the mass flow of the continuous phase and the mass flow of the disperse phase on the droplet diameter was investigated. Furthermore, the droplet detachment mechanisms were identified. Droplet diameters with small diameter fluctuation between 175 µm and 500 µm could be realized, which allows a precise adjustment of the Ca and We Number in the subsequent scaled high pressure homogenizer disruption unit. The determined influence of geometry and process parameters on the resulting droplet size and droplet detachment mechanism agreed well with literature on microfluidics. Furthermore, droplet trajectories in an exemplary scaled high-pressure homogenizer disruption unit are presented which show that the droplets can be reinjected on a trajectory close to the center axis or close to the wall, which should result in different stresses on the droplets.

The seed habit is the most complex and successful method of sexual reproduction in vascular plants. It represents a remarkable moment in the evolution of plants that afterwards spread on land. In particular, seed size had a pivotal role as for evolutionary success and agronomic trait, especially in the field of crop domestication. Given that crop seeds constitute one of the primary products for consumption, it follows that seed size represents a fundamental determinant of crop yield. This adaptative feature is strictly controlled by genetic traits from both maternal and zygotic tissues, although seed development and growth are also affected by environmental cues. Despite being a highly exploited topic for both basic and applied research, there are still many issues to be elucidated as for developmental biology as well as for agronomic science. This review addresses a number of open questions related to cues that influence seed growth and size, and how developmental processes are influenced by them. Besides, new insights on the genetic-molecular control of this adaptive trait are presented.

Knowledge of a lasers beam’s profile throughout a laser system and experiment can help immensely in diagnosing laser problems and assisting in beam alignment and focusing at a sample. Obtaining such profiles is a trivial task in the ultraviolet-visible wavelength range but more challenging with near-infrared to infrared beams. Scientific grade bolometer arrays, suitable for such a task, do exist but are extremely costly, relatively large and have a large pixel size, of the order of 80 μm, which is adequate for profiling larger beams but poses an issue when trying to profile sub 100 μm beams for example at a focal point. This communication identifies a micro-bolometer array for near- to mid-infrared laser beam profiling, which is extremely low cost. In addition, the device is very compact, enabling use in confined spaces, and has a small, 12 μm, pixel size permitting the profiling of focused laser beams. The best scientific grade device identified has a pixel size of 17 μm. This device is a powerful tool for infrared laser spectroscopists, reducing the time required to measure the spot size of beams and to achieve spatial overlap of multiple infrared beams as used in two-dimensional infrared spectroscopy, saving many hours of setup time. The use of the bolometer array as a spectrographic detector and probe of long-term beam drifts is also demonstrated.

Having garnered significant attention in the scientific community over the past decade, Wire Arc Directed Energy Deposition (arc-DED) technology is at the heart of this investigation into additive manufacturing parameters. Singularly focused on invar as the selected material, the primary objective revolves around devising an indirect cord height measurement approach. This innovative methodology involves the seamless integration of internal signals and sensors, enabling the derivation of crucial measurements sans the requirement for direct physical interaction or conventional measurement methodologies. Through the course of this research, meticulous alteration of deposition parameters is undertaken to thoroughly scrutinize their influence on the ultimate cord dimensions. The fusion of cutting-edge manufacturing techniques with advanced sensor technology constitutes the essence of this endeavor, offering substantial potential to augment precision and efficiency in additive manufacturing processes. Remarkably cost-effective, this solution circumvents the need for intricate measurements and significantly contributes to the proper layer-by-layer growth process.

Background and Objectives: To assess femoral shaft bowing (FSB) in the coronal and sagittal planes and introduce the clinical implications of total knee arthroplasty (TKA) by analyzing a three-dimensional (3D) model with virtual implantation of the femoral component. Materials and Methods: Sixty-eight patients (average age: 69.1 years) underwent 3D model reconstruction, incorporating medullary canals, by importing computed tomography (CT) data into Mimics® software. A mechanical axis (MA) line was drawn from the midportion of the femoral head to the center of the intercondylar notch; proximal/distal straight centerlines (length, 60 mm; diameter, 1 mm) were placed in the center of the medulla canal. Acute angles between the two centerlines were measured as lateral and anterior bowing. The acute angle by distal centerline and MA line was measured as distal coronal and sagittal alignment in both anteroposterior (AP) and lateral views. The diameter of curve (DOC) of the medulla along the posterior border was measured. Results: The mean lateral bowing on the AP view was 3.71°, and the mean anterior bowing on the lateral view was 11.82°. The average DOC of the medullary canal was 1501.68 mm. The distal coronal alignment of all femurs was an average of 6.40°, and the distal sagittal alignment was 2.66°. Overall, 22 femurs had coronal bowing, 42 had sagittal bowing, and 15 had both. Conclusion: In Asians, FSB is present in coronal, sagittal, or both directions. Increased anterolateral FSB may lead to cortical abutment in the sagittal plane despite limited space in the coronal plane. During TKA, distal coronal alignment can guide distal femoral valgus cut angle, whereas distal sagittal alignment helps anticipate femoral component positioning, avoiding anterior notching. Osteotomy along the anterior cortical bone to prevent notching may result in outliers due to differences between distal sagittal alignment and distal anterior cortical axis.

In order to solve the labor-intensive and time-consuming problem in the process of measuring yak body ruler and weight in yak breeding industry in Qinghai Province, a non-contact method for measuring yak body ruler and weight was proposed in this experiment, and key technologies based on semantic segmentation, binocular ranging and neural network algorithm were studied to boost the development of yak breeding industry in Qinghai Province. Main conclusions: (1) Study yak foreground image extraction, and implement yak foreground image extraction model based on U-net algorithm; select 2263 yak images for experiment, and verify that the accuracy of the model in yak image extraction is over 97%. (2) Develop an algorithm for estimating yak body ruler based on binocular vision, and use the extraction algorithm of yak body ruler related measurement points combined with depth image to estimate yak body ruler. The final test shows that the average estimation error of body height and body oblique length is 2.6%, and the average estimation error of chest depth is 5.94%. (3) Study the yak weight prediction model; select the body height, body oblique length and chest depth obtained by binocular vision to estimate the yak weight; use two algorithms to establish the yak weight prediction model, and verify that the average estimation error of the model for yak weight is 10.7% and 13.01% respectively.

This paper presents geometric analyses of welded frames after free relaxing and vibratory stress relief (VSR). Respected frames were tested components of a prototype packaging machine. Two types of relaxation were carried out to remove stresses introduced as a result of welding process. One of the frame was subjected to free relaxing, while the other one to accelerated vibration relaxing. Detection of the frame geometry changes was performed using a photogrammetric system. In addition, an evaluation of the geometry change was conducted for fifteen variants of steel frame support. A comparative analysis of the geometric deviations of the frames after free and vibratory stress relief confirmed the assumption that the frame after vibration stress relief better reproduces the nominal dimensions. Nevertheless, it should be emphasized that after vibratory stress relief the frame is not subject to further deformation, which is a desirable effect. In the case of free relaxing, the frame undergoes dimensional changes in a random manner. In summary, carrying out accelerated vibratory stress relief allows control of spontaneous dimensional changes in the designed frame of a packaging machine resulting from spontaneous relaxation of stresses arising from the welding process. The shortening of the relaxation process of the welded frame is also an unquestionable advantage.

The existence of multiple copies of genes is a well-known phenomenon. A gene family is a set of sufficiently similar genes, formed by gene duplication. In earlier works conducted on limited number of completely sequenced and annotated genomes it was found that size of gene family and size of genome are positively correlated. Additionally, it was found that several atypical microbes deviated from the observed general trend. In this study, we reexamined these associations on a larger dataset consisting of 1484 prokaryotic genomes and using several ranking approaches. We applied ranking methods in such a way that genomes with lower number of paralogs would have lower rank. Until now only simple ranking methods were used; we applied the Kemeny optimal aggregation approach as well. Regression and correlation analysis were utilized in order to accurately quantify and characterize the relationships between measures of paralog indices and genome size. In addition, boxplot analysis was employed as a method for outlier detection. We found that, in general, all paralog indexes positively correlate with an increase of genome size. As expected, different groups of atypical prokaryotic genomes were found for different types of paralog quantities.

This article is about a framework for determining the degree of realism of any given 1 passenger ride motion discomfort measurement formula. After providing some context and reviewing 2 evidence of deficiency in currently popular ride motion discomfort measurement formulas, the article 3 outlines the research program that needs to be carried out in order to establish such a framework. 4 The research begins with gathering recordings of uncomfortable ride motion episodes encountered in 5 a chosen type of passenger transport service. It then has test subjects compare the episodes via a ride 6 motion simulator and adjust their amplitudes pair wise until they cause equal discomfort. It explains 7 how to take the pair wise amplitude adjustments and determine amplitude adjustments that bring all 8 of the motion episode recordings to a common level of discomfort so that they form a normalized set. 9 Then, the lower the scatter of the scores assigned by any given discomfort measurement formula to 10 the members of that set, the more realistic that formula will be for the chosen service.

The aim of this paper is to at first evaluate the influence of three key parameters including weld current, weld time and electrode force on nugget diameter and tensile strength in resistance projection welding. Then, a 2-D axis-symmetric finite element model is developed to simulate the projection welding and predict the nugget diameter. Finally, the FEM results are compared to experimental data to verify the simulation model and simulated results. In the finite element model, the temperature-dependent material properties were taken into account.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

The implementation of sentinel lymph node (SLN) biopsy is changing the scenario in the surgical treatment of early-stage cervical cancer and the oncologic safety of replacing bilateral pelvic lymphadenectomy with SLN biopsy is currently under investigation. One of the undisputed values of SLN biopsy is its diagnostic accuracy in detecting low-volume metastases (LVM) via pathologic ultrastaging. In early-stage cervical cancer, the reported incidence of LVM ranges from 4 to 20%. The prognostic impact and the role of adjuvant treatment in patients with LVM is still unclear. Some non-prespecified analyses in prospective studies showed no impact on the oncologic outcomes compared to node-negative disease. However, the heterogeneity of the studies, the differences in the disease stage and the use of adjuvant treatment, and the concomitant pelvic lymphadenectomy (PLND) make any conclusion on this topic hard. Current guidelines suggest considering micrometastasis (MIC) as a node-positive disease, while isolated tumor cells (ITC) as a node-negative disease, with a low level of evidence. This review aims to highlight the unanswered questions about the definition, identification, prognostic and therapeutic role of LVM and underline the present and future challenges we are facing. We hope this review will guide further research, giving robust evidence on LVM and their impact on clinical practice.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

As companies increasingly undergo digital transformation, the role of talent management pro-cesses becomes pivotal in enhancing overall organizational performance. The research addresses the significance of talent management in corporate digital transformation, examining whether variations in the digitalization of these processes can be attributed to company size. A qualitative approach was employed, utilizing a questionnaire, collecting responses from 202 organizations across diverse sectors. Findings reveal disparities in digitalization throughout the talent man-agement process, with pronounced presence in the attracting, selecting, and rewarding phases, but diminishing in deployment and development, further declining in planning. A positive cor-relation between company size and adoption of specific digital platforms was observed. Larger enterprises exhibit greater utilization of digital platforms in talent deployment and development. Moreover, corporate communication tools are consistently utilized in the rewarding phase, irre-spective of company size. These findings offer practical insights for organizations to optimize their digitalization strategies based on their scale, thereby contributing to more effective and tailored digitalization endeavors. The uniqueness of this research lies in its exploration of the in-fluence of company size on the digitalization of talent management processes and its potential to explain variations across different stages of these processes.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

Single-particle inductively coupled plasma mass spectrometry (spICP-MS) has been used for particle size measurement of diverse types of individual nanoparticles and micrometer-sized carbon-based particles, such as microplastics. However, its applicability to the measurement of micrometer-sized non-carbon-based particles such as silica (SiO2) is unclear. In this study, the applicability of spICP-MS to particle size measurement of non-porous/mesoporous SiO2 micro-spheres with a nominal diameter of 5.0 µm or smaller was investigated. Particle sizes of these microspheres were measured using both spICP-MS based on a conventional calibration approach using an ion standard solution and scanning electron microscopy (SEM) as a reference technique and the results were compared. The particle size distributions obtained using both techniques were in agreement within analytical uncertainty. The applicability of this technique to the detection of metal-containing protein-binding mesoporous SiO2 microspheres was also investigated. Bound iron (Fe)-containing proteins (i.e., lactoferrin and transferrin) of mesoporous SiO2 microspheres were detected using Fe as a presence marker for the proteins. Thus, spICP-MS is applicable to the particle size measurement of large-sized and non-porous/mesoporous SiO2 microspheres; it has considerable potential for element-based detection and qualification of bound proteins of mes-oporous SiO2 microspheres in a variety of applications.

This paper presents design and optimization of a small-size electromagnetic induction heating control system powered by a 3.7V-900mAh lithium battery and featuring an LC series resonant full bridge inverter circuit, which can be used in small size materials heating applications, such as micro medical devices. The effects of resonant capacitance, inductor wire diameter, heating tube material and wall thickness are studied to maximize the heating rate of the workpiece and meantime reduce the temperature rise of the NMOS transistor. The optimal circuit configuration meeting the design requirements was finally identified via comparing the operational parameters and NMOS transistor loss under different circuit conditions. The validation experiments were conducted on a designed electromagnetic induction smoking devices. The results indicate that under an output current of 4.6A, the heating tube can reach up to the temperature target of 250℃ within 11 seconds, and all NMOS transistors stay below 50°C in a 5 minutes heating process.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the synthesis as well as theoretical considerations concerning to design of gear size ranges. The synthesis consists in composition (aggregation) of single details into units – according to the rule: “from details up to general view”. The basics of the object-oriented synthesis were formulated. Furthermore, the consecutive stages of synthesis were formulated. The interactions between these stages were discussed. Some aspects were described in details e.g.: creation of interfaces for performance of the embodiment phase the designed artefact via CAD system drawing with specification (dimensions are still parametrically set). The final step of the procedure is creation of so called substantial (concrete) form of artifacts i.e. final assignment of dimensions which stored in the special data base. The final stage of the design process is issuing of technical documentation (technical drawings) created automatically via CAD system. The considerations are terminated by the list of advantages connected with the object-oriented approach to design (in comparison to the traditional way).

This study systematically addresses the challenge of accurately modeling memristors, focusing on four distinct types doped with tungsten, tin, chromium, and carbon, fabricated by Known Inc. A comprehensive characterization was performed by subjecting the devices to sinusoidal excitations with varying frequencies and amplitudes, followed by data averaging and high-frequency filtering. The resulting measurements were fitted using three prominent memristor models: VTEAM, MMS, and Yakopcic, with additional bespoke modifications assessed. These models, typically formulated as coupled algebraic-differential equations integrating electrical quantities (voltage and current) with internal state variables governing device dynamics, were optimized using two robust approaches: (1) interior-point optimization with gradient-based search, and (2) Nelder-Mead gradient-free optimization, both with box constraints applied. A thorough comparison and discussion of the optimized model parameters ensued, accompanied by an examination of sensitivity to diverse frequency and amplitude ranges. The findings inform conclusions and provide a foundation for future refinements, underscoring the importance of multi-model evaluation and advanced optimization strategies in precise memristor modeling. The presented methodology offers a valuable framework for elucidating optimal modeling paradigms tailored to specific memristor architectures and operating regimes, ultimately enhancing their integration in emerging neuromorphic and computational applications.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

This study introduces a novel predictive model for atomization droplet size, developed through comprehensive data collected under elevated temperature and pressure conditions using a twin swirl airblast nozzle. The model, grounded in flow instability theory, has been meticulously parameterized using the Particle Swarm Optimization (PSO) algorithm. Through rigorous analysis, including analysis of variance (ANOVA), the model has demonstrated robust reliability and precision, with a maximum relative error of 19.3% and an average relative error of 6.8%. Compared to the classical atomization model by Rizkalla and Lefebvre, this model leverages theoretical insights and incorporates a range of interacting variables, enhancing its applicability and accuracy. Spearman correlation analysis reveals that air pressure and the air pressure drop ratio significantly negatively impact droplet size, whereas the fuel-air ratio (FAR) shows a positive correlation. Experimental validation at ambient conditions shows that the model is applicable with a reliability threshold of ≥0.13 and highlight the predominance of the pressure swirl mechanism over aerodynamic atomization at higher fuel flow rates (q > 1.25 kg/h). This research effectively bridges theoretical and practical perspectives, offering critical insights for the optimization of airblast nozzle design.

The achievement of size uniformity and monodispersity in perovskite quantum dots (QDs) requires the implementation of precise temperature control and the establishment of optimal reaction conditions. Nevertheless, the accurate control of a range of reaction variables represents a considerable challenge. This study addresses the aforementioned challenge by employing manganese (Mn) doping to achieve size uniformity in CsPbBr₃ perovskite QDs without the necessity for precise control of the reaction conditions. By optimizing the Mn:Pb ratio, it is possible to successfully dope CsPbBr₃ QDs with appropriate concentrations of Mn²⁺ and achieve a uniform size distribution. The spectroscopic measurements on single QDs indicate that the appropriate Mn²⁺ concentrations can result in a narrower spectral linewidth, a longer photoluminescence (PL) lifetime, and a reduced biexciton Auger recombination rate, thus positively affecting the PL properties. This study not only simplifies the size control of perovskite QDs, but also demonstrates the potential of Mn-doped CsPbBr₃ QDs for narrow linewidth light-emitting diode applications.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the analysis as well as theoretical considerations concerning to design of gear size ranges. This analysis consists in decomposition of the designed artefact (a gear) according to the rule “from general to details view”. The basics of the object-oriented analysis were formulated. Furthermore, design phases and the objects related to theses phases were discussed. The following models have been considered: hierarchical model, entity-relationship model, data-flow model and object model. Analysis is additionally connected with interactions between particular design phases.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

This study presents a reproducible and scalable method for synthesizing silica nanoparticles (SNPs) with controlled sizes below 200 nm, achieved by systematically varying three key reaction parameters: ammonium hydroxide concentration, water concentration, and temperature. SNPs with high monodispersity and controlled dimensions were produced by optimizing these factors. The results indicated a direct correlation between ammonium hydroxide concentration and particle size, while higher temperatures resulted in smaller particles with increased polydispersity. Water concentration also influenced particle size, with a quadratic relationship observed. This method provides a robust approach for tailoring SNP sizes, with significant implications for biomedical applications, particularly in drug delivery and diagnostics. Using eco-friendly solvents such as ethanol further enhances the sustainability and cost-effectiveness of the process.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Autosomal dominant polycystic kidney disease (ADPKD) is an inherited disorder characterized by renal tubular cystic dilatations. The cysts can develop anywhere along the nephron and over time the cystic dilatation lead to kidney enlargement. On the other hand, the cysts begin to reduce the number of functional nephrons as a consequence of cystic expansion that further contributes to the decline in renal function over the years. The pressure exerted by the dilated cysts lead to compensatory mechanisms that further contribute to the decline in renal function. These structural changes are responsible of glomerular hyperfiltration states, albuminuria, proteinuria, and haematuria. However, the presentation of ADPKD varies in children from a completely asymptomatic child with incidental ultrasound detection of cysts to a rapidly progressive disease. There have been reports of early onset of ADPKD in children younger than 2 years that showed a more rapid decline in renal function. ADPKD is caused by mutation in PKD1 and PKD2 genes. Today, the PKD1 gene mutation seems to account for up to 85% of the cases worldwide, and it is associated with worse renal outcomes. Individuals with PKD2 gene mutation seem to present a milder form of the disease, with a more delayed onset of end stage kidney disease. The cardinal sign of ADPKD is the presence of renal cysts during renal ultrasound. The current guidelines provide the clinicians the recommendations for genetic testing in children with a positive family history. Given that the vast majority of children with ADPKD present with normal or supra normal kidney function we explored the glomerular filtration rates dynamics and the renal ultrasound adjusted percentiles. 14 out of 16 patients had kidney percentile over 90%. The gene mutations were equally distributed among our cohort. In addition, we compared the modified Schwartz formula to the quadratic equation after adjusting the serum creatinine measurements. It seems that even though children with ADPKD have enlarged kidneys, the renal function is more likely normal or near normal when the quadratic estimation of glomerular filtration rate is used (qGFR tended to be lower, 111.95 ± 12.43 ml/min/1.73m2 compared to Schwartz eGFR 126.28 ± 33.07ml/min/1.73m2, p=0.14). Also, when the quadratic equation was employed, not even a patient reached the glomerular hyperfiltration thresholds. The quadratic formula showed that glomerular filtration rates are linear or slightly decreasing after 1-year of follow-up (Quadratic ΔeGFR=0.32±5.78ml/min/1.73m2) as opposed to Schwartz formula that can falsely classify children in a hyperfiltration state ΔeGFR=7.51±19.46ml/min/1.73m2), p=0.019.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

This paper presents a compact wideband circularly polarized cross dipole antenna with low-pass filter response. It consists of two pairs of folded crossed dipole arms printed separately on both sides of the top substrate, and the two dipole arms on the same surface are connected by an annular phase-shifting delay line to generate circular polarization. A bent metal square ring and four small metal square rings around the cross dipoles are employed to introduce new resonant frequencies, effectively extending the impedance and axial ratio bandwidth. Four square patches printed on the middle substrate are connected to the ground plane by the vertical metal plates, in order to reduce the antenna height. Thus, a compact wideband circularly polarized antenna is realized. In addition, a transmission zero can be introduced at the upper frequency stopband by the bent metal square rings, without using extra filter circuits. For verification, the proposed model is implemented and tested. The overall size of the model is 90mm×90mm×33mm(0.37λ0×0.37λ0×0.14λ0, λ0 denotes the center operating frequency). The measured impedance bandwidth and 3 dB axial ratio bandwidth are 53.3% and 41%, respectively. More than 15 dB upper-band radiation suppression level is realized, indicating a good low-pass filter response.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high-precision seawater refractive index measurements. A seawater refractive index measurement system based on position-sensitive detectors is an effective means to achieve high-precision measurement of seawater refractive index. However, in the actual seawater refractive index measurement process, the impact of the measurement error caused by the jitter signal obtained from the measurement on the measurement results cannot be ignored. In this paper, we theoretically analyse the causes of the long jitter signals during seawater refractive index measurement and quantify the influencing factors. Through the analysis, it can be seen that the angle between the two windows in the refractive index measurement area of seawater causes a great error on the measurement results, so the angle between the two windows should be controlled within 2.06° in order to effectively reduce the measurement error. At the same time, the factors affecting the measurement accuracy of the position-sensitive detector are analysed, and the factors leading to the reduction of the measurement accuracy of the position-sensitive detector are mainly the background light, the size of the photosensitive surface, and the change of the temperature of the working environment. For the above factors, we add a narrow-band filter with a bandwidth of 0.9nm in front of the photosensitive surface of the position-sensitive detector during the construction of the measurement system, so as to filter out stray light other than the signal light source. On the premise of ensuring the measuring range of the refractive index of seawater, a position-sensitive detector with a photosensitive surface size of 4 mm×4 mm was selected. In order to reduce the temperature variation of the working environment of the position-sensitive detector, the measurement system was partitioned. In order to validate the testing error range of the optimised test system, standard seawater samples under the same conditions were measured. It can be seen that the jitter signal of the measurement system has been reduced from 0.0022mm before the optimisation to 0.0011mm after the optimisation, and the deviation of the refractive index has been reduced by 1.09×10−8RIU. The experimental results show that the refractive index of seawater has been effectively reduced by adjusting the optical path and the structure of the seawater refractive index measurement system.

Federated learning is an effective approach for preserving data privacy and security, enabling machine learning to occur in a distributed environment and promoting its development. However, an urgent problem that needs to be addressed is how to encourage active client participation in federated learning. The Shapley Value, a classical concept in cooperative game theory, has been utilized for data valuation in machine learning services. Nevertheless, existing numerical evaluation schemes based on the Shapley Value are impractical as they necessitate additional model training, leading to increased communication overhead. Moreover, participants’ data may exhibit Non-IID characteristics, posing a significant challenge to evaluating participant contributions. Non-IID data weakens the marginal effects of participants, which in turn affects model accuracy and leads to underestimated contribution measurements. Current works often overlook the impact of heterogeneity on model aggregation. This paper presents a fair federated learning contribution measurement scheme that addresses the need for additional model computations. By introducing a noval aggregation weight, it enhances the accuracy of contribution measurement. Experiments on the MNIST dataset show that the proposed method can accurately compute the contributions of participants. Compared to existing baseline algorithms, the model accuracy is significantly improved, with a similar time cost.

Ferritin is an indirect marker for total body iron stores. Comparison of the ferritin concentrations in the meconium with the concentrations of proteins regulating iron metabolism could aid better understanding of principles behind the adjustment between the fetal iron pool and newborn body size. Ferritin, transferrin, haptoglobin, ceruloplasmin, lactoferrin, myeloperoxidase, neutrophil gelatinase-associated lipocalin (NGAL) and calprotectin concentrations were measured by ELISA in meconium samples from 122 neonates. The neonates were classified according to the meconium ferritin tertiles and the values were collated with the meconium concentrations of other proteins and newborn body weight and length measurements. Increasing ferritin concentrations in meconium in consecutive tertiles (p < 0.05) were parallel to increased NGAL concentrations (p < 0.05). The interrelationships between the meconium concentrations of transferrin, haptoglobin and NGAL as well as between myeloperoxidase, calprotectin and lactoferrin are maintained in all subsequent tertiles of ferritin concentrations, (p < 0.05). In contrast to ferritin, increasing meconium NGAL concentrations in consecutive tertiles were linked to increased concentrations of transferrin, haptoglobin, lactoferrin and myeloperoxidase (p < 0.05) and of calprotectin, ferritin and ceruloplasmin (p < 0.1). Meconium ceruloplasmin concentrations correlate exclusively with neutrophil granule proteins, i.e. myeloperoxidase, NGAL, lactoferrin and calprotectin (p < 0.05). Meconium ferritin concentrations negatively correlates with birth weight (r= -0.20) and length (r= -0.31) of neonates, whereas NGAL concentrations just with birth length (r= -0.26). The remaining proteins did not show such relationships with the size of the newborn. High meconium concentrations of both ferritin and NGAL may specifically characterize neonates of smaller size. High meconium concentrations of both ferritin and NGAL may specifically characterize neonates with lower body measurements. Correlations between meconium transferrin, haptoglobin and NGAL may confirm the interrelationships of these proteins for proper iron control and transport in the intrauterine environment. Meconium ceruloplasmin concentrations may reflect the control of neutrophil activity in utero.

Nitrates can cause severe ecological imbalances in aquatic ecosystems, with considerable consequences for human health. Therefore, monitoring this inorganic form of nitrogen becomes essential for any water quality management structure. This research aimed at developing a novel Nitrate Portable Measurement System (NPMS) for monitoring nitrate concentrations in water samples. NPMS is a reagent-free ultraviolet system developed using low-cost electronic components. Its operation principle is based on Beer-Lambert law for measuring Nitrate concentrations in water samples through light absorption in the spectral range 295-315 nm. The system is equipped with ready to use ultraviolet sensor, Light Emission Diode (LED), op-amp, microcontroller, liquid crystal display, quartz cuvette, temperature sensor, and battery. All the components are assembled in a 3D-printed enclosure box which allows a very compact self-contained equipment, with high portability, enabling field and near real time measurements. The proposed methodology and the developed instrument were used to analyse multiple nitrate standard solutions. The performance was evaluated in comparison with the Nicolet Evolution 300, a classical UV-Vis spectrophotometer. The results demonstrate a strong correlation between the retrieved measurements by both instruments within the investigated spectral band and for concentrations above 5 mg NO3- /l.

In the realm of physical activity and sports science, motion tracking emerges as an important tool for specialists aiming to analyze movement data, whether for daily life activities or enhancing athletic performance. This study introduces an innovative approach to motion tracking through the development of a fully embedded smart shoe sensor system, which employs an inertial measurement unit (IMU) affixed to the shoe sole, coupled with six pressure sensors, to provide real-time calculation of individual stride lengths along with other vital movement statistics. Traditional motion tracking methods, which typically rely on various body-attached sensors, often necessitate substantial post-processing, delaying the feedback loop. In contrast, our system is designed to overcome these limitations by offering high-accuracy, real-time feedback with a minimal error rate of 1.88% from our experiments. Such prompt data acquisition facilitates immediate interventions by sports performance coaches or healthcare professionals, significantly contributing to injury prevention and performance enhancement. The experimental outcomes of this study underscore the system’s capability to deliver precise stride length measurements instantaneously, marking a significant advancement in motion tracking technology and its application in sports science and healthcare.

Although researchers have proposed various indentation size effect (ISE) models, these models often involve different form and number of parameters that can make our wonder which is the best in existed ISE models. Three types of ISE test data, namely, normal ISE, reverse ISE and transition of normal to reverse ISE, are used to evaluate the sixteen ISE models. The comparatively study indicates that H-J, N-G-Fs, N-G-H, N-G-A and N-G-Qs models can accurately predict the normal ISE. The reason for this is that the friction stress that is not related to dislocation activities or the indentation size effect of plastic zone has been introduced into these models. Therefore, these two factors should be considered in future ISE models. The sixteen ISE models are originally proposed to describe the normal ISE of different materials. However, to our surprise, some of these models are able to capture the reverse ISE and the transition of normal to reverse ISE of different materials. The determination coefficients (DC) of the sixteen ISE models are also determined for different materials. For reverse ISE, the highest DC value for NiCSi, TC4 and PED Ni are given by the EXP, N-G-Fs and N-G-A models, respectively. For the transition of normal to reverse ISE, the N-G-YC, N-G-Fs, and N-G-H models produce the maximum DC for ZrO2, Cu and Y2O3-ZrO2, respectively. Moreover, the mean DC of the N-G-Fs model is the maximum among the sixteen ISE models, followed by the N-G-H model, but they cannot accurately predict the reverse ISE. Therefore, the N-G-Fs and N-G-H models should be further modified to accurately predict the reverse ISE.

Predicting the thermophysical properties of designed materials at the nanoscale is crucial. However, this remains a significant challenge despite numerous efforts by researchers and scientists. This paper presents a unified thermodynamic model to study the size and shape-dependent cohesive energy and the melting temperature of semiconductor nanosolids, including InSb, ZnSe, CdS, and CdSe. The model provides insight into the thermal stability of nanosolid materials by considering the combined impact of size, shape, and packing density. The finding indicates that smaller nanoparticles exhibit a lower cohesive energy than larger ones. Our unified thermodynamic model yields results consistent with experimental values and demonstrates a closer agreement than those from the universal liquid drop model of size-dependent cohesive energy, which includes a shape factor of α = 2/3 for nanowires. According to the results, the melting temperature of nanoparticles drops as their size decreases. Below a diameter of 5 nm, this trend becomes more noticeable. In the nano-scale domain, the nanoparticle's shape also matters greatly. In particular, compared to tetrahedral nanoparticles, nanowires show a lesser reduction in melting temperature. Also, up to a diameter of roughly 10 nm, the melting temperatures of these nanoparticles rise with particle size. The search results show that, especially in the < 5 nm size range, the size and shape of nanoparticles significantly affect their melting point. The models accurately predict the relationship between particle size and melting point for various semiconductor nanomaterials, aligning with experimental findings. Interestingly, the information indicates a potential preference for these nanomaterials to form nanowire structures in the < 5 nm size range. Our research offers helpful insights into the thermophysical properties of these semiconducting materials, which may have significant implications for their use in a diversity of technological applications.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Despite soccer popularity, comparatively little scientific information is available concerning the assessment of youth players’ physiological characteristics. The use of medical software integrating wearable sensors to provide accurate and objective data is necessary. In the present study, the objective assessment of physical performance of 128 adolescent soccer players at two timepoints (pre-season and end-season) has been performed. Participants completed a comprehensive test battery including stability, countermovement jumps (CMJ), plyometric jumps (PJ), agility, and quick feet tests. A single Inertial Measurement Unit (IMU) sensor provided quantitative data on various performance metrics. Principal Component Analysis (PCA) reduced the dataset to four principal components (PCs) explaining over 80% of the variance: power (PC1), balance (PC2), speed/agility (PC3), and stiffness (PC4). Paired samples t-test between the two timepoints showed no significant differences in the PCs between the two timepoints, indicating that the training program did not significantly alter the assessed physical attributes. However, subtle individual changes may still inform personalized training adjustments. The study highlights the importance of continuous monitoring and individualized training strategies to optimize athlete performance and reduce injury risk.

Phytoplankton guilds are commonly characterised by dominance effects, while the main contribution to biological diversity is given by rare species. Here, we analysed the influence of rare species on taxonomic and functional diversity, described by taxa richness and composition, cell size and size abundance relationships in phytoplankton guilds. We explore these relationships at global and regional scales by analysing phytoplankton guilds from five biogeographical regions: Northern Atlantic Ocean (Scotland), South-Western Atlantic Ocean (Brazil), South-Western Pacific Ocean (Australia), Indo-Pacific Ocean (Maldives) and Mediterranean Sea (Greece and Turkey). We have comparatively analysed the phytoplankton taxonomic diversity of the whole dataset and with the datasets obtained by progressively subtracting taxa occurring in the last 1%, 5%, 10% and 25% of both numerical abundance and overall biomass. Globally 306 taxa were identified across five ecoregions with only 27 taxa accounting for the 75% of overall numerical abundance and biomass; almost the 50% of taxa were lost on every step. The removal of 1% most rare taxa significantly affected the phytoplankton size-abundance relationships and body-size structure, strongly impacting on small taxa. The progressive removal of additional rare taxa did not further affect phytoplankton size-abundance relationships and size structure.

This study utilized electrical resistivity imaging (ERI) to investigate subsurface characteristics near Nicolaus Copernicus University Polar Station on the western Spitsbergen-Kaffiøyra Plain, island in the Svalbard archipelago. Surveys along two lines, LN (148 meters) collected in 2022 and 2023 and ST (40 meters) collected in 2023, were conducted to assess resistivity and its correlation with ground temperatures. The LN line revealed a 1 to 2 meters thick resistive unsaturated outwash sediment layer, potentially indicative of permafrost. Comparing LN resistivity result between 2022 and 2023, a 600 Ohm-m decrease in the unsaturated active layer in 2023 was observed, attributed to a 5.8℃ temperature increase, suggesting a link to global warming. ERI along the ST line depicted resistivity reaching its minimum at approximately 1.6 meters, rising to over 200 Ohm-m at 4 meters, and slightly decreasing to around 150 Ohm-m at 7 meters. Temperature measurements from the ST line's monitoring well confirmed permafrost at a depth of 1.6 to 2 meters. Additionally, water content distribution in the ST line was estimated after temperature correction, revealing a groundwater table depth of approximately 1.06 meters, consistent with measurements from the S4 borehole on the ST line. This study provides valuable insights into Arctic subsurface dynamics, emphasizing the sensitivity of resistivity patterns to climate change and offering a comprehensive understanding of permafrost behavior in the region.

In order to investigate the size distributions and seasonal variations of carbonaceous aerosols (OC and EC), the carbonaceous species were collected and then analyzed by using a 9-stage Anderson-type aerosol sampler and DRI Model 2001A Thermal/Optical Carbon Analyzer on the typical industrial city Nanjing in Yangtze River Delta, China in the summer, autumn and winter of 2013 and spring of 2014. OC, EC, SOC and POC exhibited obvious seasonal variations, with the highest level in winter (39.1±14.0, 5.7±2.1, 23.6±11.7 and 14.1±5.7 μg•m^-3) and the lowest level in summer (20.6±6.7, 3.3±2.0, 12.2±3.8 and 8.4±4.1 μg•m^-3), and were mainly centralized in PM_1.1 in four seasons. The concentrations of OC in PM_1.1 varied in the order of winter > autumn > spring > summer, while EC ranked in the order of autumn > winter > summer > spring. In the PM_1.1-2.1 and PM_2.1-10, the concentrations of OC and EC decreased in the sequence of winter > spring > autumn > summer. The size spectra of OC, EC and SOC had bimodal distributions in four seasons, except for EC with four peaks in summer. The size spectra of POC varied greatly with seasons, exhibiting bimodal distribution in winter, trimodal distribution in spring and summer, and four peaks in autumn. The OC/EC ratios were 7.0, 6.3, 7.6 and 6.9 in spring, summer, autumn and winter, respectively, which demonstrated the abundance of secondary organic aerosols in Nanjing. The sources of carbonaceous aerosol varied significantly with seasons, and were dominated by vehicle exhaust, coal and biomass burning in PM_2.1, and dominant by dust, coal and biomass burning in PM_2.1-10.

The air is not the same as thousands and hundreds of years ago. In the air, suspended particles originate from natural phenomena like dust storms or volcanic activities, as well as anthropogenic pollutants such as fuel engine exhaust and everyday activities at home. The total particles in the air can be classified by sizes, such as PM10, PM2.5 or ultrafine particles. However, there are many other important factors in addition to the particle size, influencing the particle behavior and affecting our health. The surface area, chemical and biological composition, aspect ratio, and the charge are all factors characteristic of particles. OoC microfluidic chips are very useful for the pollutant toxicity measurements on various body tissues. A better understanding of pollutants will help to trace these to the potential sources. The data from the on-the-ground and satellite monitoring can be integrated into models, helping to predict and prevent pollution exposure.

The scope of this study was twofold: first, to introduce a new method in examining measurement invariance, especially with large-scale studies where a large number of group comparisons are involved: the alignment approach, where only configural invariance is necessary to achieve measurement invariance. Second, to evaluate the psychometric robustness of this approach using real-life data. Particularly, we applied this approach to examine whether the factor structure of a cognitive ability test (PGAT) exhibits measurement invariance across the 26 universities of the Kingdom of Saudi Arabia. The sample consisted of 9,849 graduate students from 26 universities around the Kingdom. The results indicated a robust configural model suggesting that the P-GAT subscales were invariant across the 26 universities. Finally, the aligned factor mean values were estimated, and factor mean comparisons of every group’s mean with all other group means were conducted for both cognitive domains (Verbal and Quantitative). In both domains, King Saud University had the highest mean score among all universities. Moreover, its mean factor score was significantly higher than any other university besides Dammam University. On the other hand, several universities allocated at the northern and Southern borders of the country exhibited the lowest factor mean scores.

Energy Measurement and Verification (M&V) aims to make inferences about the savings achieved in energy projects, given the data and other information at hand. Traditionally, a frequentist approach has been used to quantify these savings and their associated uncertainties. We demonstrate that the Bayesian paradigm is an intuitive, coherent, and powerful alternative framework within which M&V can be done. Its advantages and limitations are discussed, and two examples from the industry-standard International Performance Measurement and Verification Protocol (IPMVP) are solved using the framework. Bayesian analysis is shown to describe the problem more thoroughly and yield richer information and uncertainty quantification than the standard methods while not sacrificing model simplicity. We also show that Bayesian methods can be more robust to outliers. Bayesian alternatives to standard M&V methods are listed, and examples from literature are cited.

Stimulation of the alpha 7 nicotinic acetylcholine receptor (α7nAChR) has shown beneficial effects in several acute inflammatory disease models. This study aims to examine whether treatment with the selective α7nAChR agonist PHA 568487 can dampen inflammation and thereby improve cardiac function after myocardial infarction in mice. The possible anti-inflammatory properties of α7nAChR agonist PHA 568487 were tested in vivo using the air pouch model and in a permanent occlusion model of acute myocardial infarction in mice. Hematology parameters and cytokine levels were determined. Infarct size and cardiac function were assessed via echocardiography 24 h and one week after the infarction. Treatment with α7nAChR agonist PHA 568487 decreased 12 (CCL27, CXCL5, IL6, CXCL10, CXCL11, CXCL1, CCL2, MIP1a, MIP2, CXCL16, CXCL12 and CCL25) out of 33 cytokines in the air pouch model of acute inflammation. However, α7nAChR agonist PHA 568487 did not alter infarct size, ejection fraction, cardiac output or stroke volume at 24 h nor at 7 days after the myocardial infarction compared with control mice. In conclusion, despite promising immunomodulatory effects in the acute inflammatory air pouch model, α7nAChR agonist PHA 568487 did not affect infarct size or cardiac function after a permanent occlusion model of acute myocardial infarction in mice. Consequently, this study does not strengthen the hypothesis that stimulation of the α7nAChR is a future treatment strategy for acute myocardial infarction when reperfusion is lacking. However, whether other agonists of the α7nAChR can have different effects remains to be investigated.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

This review discusses approaches and implementations of flowrate sensing and measurement in smart inhalers for effective respiratory disease management. It highlights the importance of compliance with proper inhaling techniques and consistent adherence for managing respiratory conditions. Methods and relevant commercial and prototype research-type devices for sensing and measuring inhalation flowrate in smart inhalers are studied and compared. The study argues that utilisation of acoustic analysis and air pressure sensing is a promising approach to detect and evaluate the inhaling action ultimately allowing to improve the treatment outcomes and life quality of patients with respiratory diseases.

Models of quantum measurements are presented, including observers subject to the laws of quantum mechanics. Observers perform multiple measurements in an attempt to disprove the collapse hypothesis. It is shown that under reasonable assumptions the effort cannot succeed. Under a unitary evolution the end state is a correlation between the result of the first measurement and the result(s) of the others, consistent with the observer's collapse hypothesis. The observer may conclude that the laws of nature include a non-unitary collapse mechanism, even if one does not actually exist. Discard of information is the crucial factor which distinguishes entanglement from measurement.

A variant of the von Neumann-Wigner Interpretation is proposed. It does not make use of the familiar language of wave functionsand observers. Instead it pictures the state of the physical world as a vector in a Fock space and, therefore not, literally, a functionof any spacetime coordinates. And, rather than segregating consciousness into individual points of view (each carrying with it asense of its proper time), this model proposes only unitary states of consciousness, Q(t), where t represents a fiducial time withrespect to which both the state of the physical world and the state of consciousness evolve. States in our world's Fock space areclassified as either 'admissible' (meaning they correspond to definite states of consciousness) or 'inadmissible' (meaning they donot). The evolution of the state vector of the world is such as to always keep it restricted to 'admissible' states. Consciousness istreated very much like what Chalmers calls an "M-Property." But we try to show that problems with the quantum Zeno effect do not arise from this model.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

Vitamin D deficiencies are very common in pregnant women, raising concerns about adverse health outcomes in children. This issue has hardly been studied in multiple pregnancies, the prevalence of which has been steadily increasing. Therefore, our study investigated the relationship between newborns’ anthropometric parameters and the concentration of 25(OH)D in maternal blood of women with twin pregnancies and umbilical cord blood. The study included 50 women who gave birth after the 36th week of twin gestation. 25(OH)D was determined in maternal blood collected during the antenatal period and in the umbilical cord blood of 100 newborns. Anthropometric parameters of the newborns (birth weight, length, head and chest circumference) were obtained from hospital records. Data on nutrition and lifestyle during pregnancy were collected from the patients during an interview conducted by a dietitian. No relationship between maternal and neonatal cord blood vitamin D concentrations and any of the anthropometric parameters of the newborns was found. However, only 6% of the mothers and 13% of the newborns had vitamin D deficiency (≤20 ng/mL). The type of pregnancy and maternal height were the main factors associated with neonatal size. Newborns from dichorionic pregnancies were on average 202 g heavier (p<0.001) and 1 cm longer (p=0.006) than newborns from monochorionic pregnancies. Newborns of mothers ≤ 160 cm in height had on average 206 g lower birth weight (p=0.006) and were 3.5 cm shorter (p=0.003) compared to newborns of taller mothers. Therefore, in our study, neonatal size of the twins was not related to the vitamin D status but to other factors such as the type of pregnancy and maternal height.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

Influencer marketing has become a pivotal component of digital marketing strategies, offering brands a unique way to connect with audiences through trusted voices. However, measuring the return on investment (ROI) from influencer marketing campaigns can be challenging due to the intangible nature of brand influence and engagement. This abstract explores various techniques and strategies to measure and optimize ROI in influencer marketing. Measurement Techniques: The paper delves into both quantitative and qualitative methods for assessing influencer marketing ROI. Quantitative techniques include tracking metrics such as impressions, clicks, conversions, and sales, using tools like Google Analytics and social media insights. Additionally, advanced attribution models, such as multi-touch attribution and econometric modeling, are discussed for more accurately linking influencer activities to business outcomes. Qualitative approaches involve sentiment analysis and brand awareness studies, which help gauge the impact of campaigns on brand perception and customer loyalty. Optimization Strategies: To maximize the effectiveness of influencer marketing, the paper outlines several optimization strategies. These include selecting the right influencers based on audience alignment and engagement rates, setting clear and measurable campaign goals, and employing A/B testing to refine content and strategies. The importance of long-term partnerships and content diversification is also emphasized, as they can enhance authenticity and sustain audience interest. The abstract concludes that a comprehensive approach combining rigorous measurement techniques and strategic optimization can significantly enhance the ROI of influencer marketing campaigns. By continuously analyzing data and refining strategies, brands can better leverage influencer partnerships to achieve their marketing objectives.

Different values of the Hubble constant for extragalactic objects are not considered here. We give a number of examples of the extreme accordance of expansion rates of different fields of knowledge with the cosmological expansion rate. The coincidence of the expansion rates means that a common cause is almost inevitable. All these examples are gravitationally bound in themselves and in this case are subject to cosmological expansion. According to standard theory, this should not happen. We therefore question the common boundary of gravity and expansion for both theoretical and observational reasons and conclude that all gravitationally dominated objects participate in cosmological expansion or scale drift, contrary to general doctrine. The space expands with its contents while numerically maintaining distance, radius, rotation time and density. What is generally interpreted as an expansion is obviously a scale drift with a drift rate that corresponds to the size of the Hubble constant. The Earth is subject to expansion and scale drift. This results in numerically constant measured values. This drift apparently also applies to distant galaxies and other objects. The cosmological red shift is not interpreted here as a Doppler effect and numerical increase in distances, but in accordance with standard theory as an expansion or drift of the space-time scale. The expansion of the radii of galaxies makes the assumption of dark matter superfluous. The continents and our everyday environment are not subject to expansion or scale drift.

The forest regeneration phase in Sweden commonly involves mechanical soil preparation followed by planting of Scots pine or Norway spruce seedlings. The prepared soil offers planting positions with different properties, including decreased damage by pine weevil (Hylobius abietis L.). Nitrogen fertilization can be applied at the time of planting to aid establishment of the seedlings. In this study we compared the effect of organic nitrogen-fertilization for different planting positions, and seedling sizes on early survival and growth of Scots pine and Norway spruce seedlings. The main planting positions were capped mound, hinge, and mineral soil. Seedlings planted close to organic material were categorized as “low quality positions”, since proximity to organic material increase pine weevil attraction. Higher mortality rates related to pine weevil damage were recorded for seedlings planted in the low-quality positions, regardless of seedling size or N-fertilization. Pine weevil attack rates increased with increasing seedling size. Growth was in general lowest in mineral soil positions. The effect of organic N-fertilization on growth was positive for spruce regardless of planting positions and seedling size, while depending on planting position and seedling size for pine, indicating that effects of organic N-fertilization depend on seedling species, -size and planting position.

The present work studies the concept of productivity in shipbuilding and how it should be measured. The existing metrics, shipbuilding process and shipyard organization were studies in order to choose the most adequate metrics which would allow the measuring of a shipyard productivity in a systematic and holistic way. This is achieved by gathering the man-hours spent in each ship organized by cost centre and using Compensated Gross Tonnages as the measure of output from the shipyard. Data was gathered for thirty ships built in the same European yard organized by cost centre. From the data collected it was found that the ratio of hours spent in outfitting to the hours spent in structures is proportional to the complexity of the ship. There was also opportunity to study the work reduction resulting from building ships in series and the shares of labour for ships series and across ship types.

Qualitative and quantitative values estimation is a crucial aspect of social data science and plays a vital role in social and psychological research. Numerous methods of personal values measurement such as Schwartz Value Survey (SVS) and its re-modified versions have been proposed and invented, but many are challenged with one or more limitations. In this article, an alternative approach in a new paradigm of values measurement called Kabiru’s Value Survey (KVS) was proposed to measure the relative degree of importance or significance attached to particular value-actions of an individual(s) in a given population over a period. The methodological innovations in KVS unlike other existing methods of human value measurement include the use of habitually reported practices associated with a particular value-action in place of judging the series of Schwartz hypothetical statements, the use of multiple dependent variables rather than a single coded hypothetical statement. In terms of data analysis, a new approach of multivariate compression is introduced which merges the chain of multiple dependent variables into one coded scale. Psychometric result interpretation is also another innovative aspect of KVS methodology. Finally, the proposed methodology however solved some of the criticized limitations of the other methods of human value measurement.

Complex-structured polymeric microparticles hold significant promise as advance in next-generation medicine mostly due to demand from developing targeted drug delivery. However, the conventional methods for producing these microparticles of defined size, shape and sophisticated composition often face challenges in scalability, reliance on specialized components such as micro-patterned templates, or have limited control over particle size distribution and cargo release kinetics. In this study, we introduce a novel and reliably scalable approach for manufacturing microparticles of defined structures and sizes with variable parameters. The concept behind this method involves the deposition of a specific number of polymer layers on a substrate with low surface energy. Each layer can serve as either the carrier for cargo or a programmable shell-former with predefined permeability. Subsequently, this layered structure is precisely cut into desired-sized blanks using a laser. The manufacturing process is completed by applying of heat to the substrate what results on sealing the edges of the blanks. The combination of the high surface tension of the molten polymer and the low surface energy of the substrate enables the formation of discrete particles, each possessing semi-spherical or other designed geometries determined by their internal composition. Such anisotropic microparticles are envisaged versatile applications.

Asphaltene precipitation and deposition pose significant operational challenges in both reservoirs and surface facilities by inducing formation damage. To understand the kinetics involved in asphaltene particle nucleation, growth, and aggregation, this study employed confocal microscopy and centrifuge-based methods under a unified set of experimental parameters. The acquired time-resolved particle size images were analyzed using MIPAR image processing software, while asphaltene mass yield was quantitatively evaluated through centrifugation. Experimental conditions were varied to study the effects of heptane concentration, asphaltene concentration, and shear rate. Notably, this investigation introduces, for the first time, the parameter of particle count as an additional variable influencing asphaltene mass production. This study aims to discern how particle count correlates with asphaltene mass yield over time. Results indicate that the minimum mean particle diameter was observed to be 2 microns, which progressively grew up to 80 microns. The mean particle diameter exhibited a positive correlation with both asphaltene concentration and shear rate, whereas an inverse correlation was seen with heptane concentration. Furthermore, the asphaltene mass yield was found to increase with greater asphaltene and heptane concentrations, as well as with higher shear rates. The relationship between mean particle diameter and mass yield was found to be nonlinear. In the early stages, a higher prevalence of small particles contributed to a greater total particle count, while at later stages, particle aggregation led to the formation of larger particles that influenced the overall asphaltene mass. The insights gained from understanding the relationship between particle diameter, count, and mass yield are crucial for advancing the fundamental science of asphaltene precipitation and deposition. These findings may also guide future research that relies solely on particle counts for assessing asphaltene deposition.

Polymeric particles made up of biodegradable and biocompatible polymers such as poly(lactic-co-glycolic acid) (PLGA) are promising tools for several biomedical applications including drug delivery. Particular emphasis is placed on the size and surface functionality of these systems as they are regarded as the main protagonists in dictating the particle behavior in vitro and in vivo. Current methods of manufacturing polymeric drug carriers offer a wide range of achievable particle sizes, however, they are unlikely to accurately control the size while maintaining the same production method and particle uniformity, as well as final production yield. Microfluidics technology has emerged as an efficient tool to manufacture particles in a highly controllable manner. Here, we report on tuning the size of PLGA particles at diameters ranging from sub-micron to microns using a single microfluidics device, and demonstrate how particle size influences the release characteristics, cellular uptake and in vivo clearance of these particles. Highly controlled production of PLGA particles with ~100 nm, ~200 nm and >1000 nm diameter is achieved through modification of flow and formulation parameters. Efficiency of particle uptake by dendritic cells and myeloid-derived suppressor cells isolated from mice is strongly correlated with particle size and is most efficient for ~100 nm particles. Particles systemically administered to mice mainly accumulate in liver and ~100 nm particles are cleared slower. Our study shows the direct relation between the particle size varied through microfluidics and the pharmacokinetics behavior of particles, which provides a further step towards the establishment of a customizable production process to generate tailor-made nanomedicines.

Human number understanding is thought to rely on the analogue number system (ANS), working according to Weber’s law. We propose an alternative account, suggesting that symbolic mathematical knowledge is based on a discrete semantic system (DSS), a representation that stores values in a semantic network, similar to the mental lexicon or to a conceptual network. Here, focusing on the phenomena of numerical distance and size effects in comparison tasks, first we discuss how a DSS model could explain these numerical effects. Second, we demonstrate that DSS model can give quantitatively as appropriate a description of the effects as the ANS model. Finally, we show that symbolic numerical size effect is mainly influenced by the frequency of the symbols, and not by the ratios of their values. This last result suggests that numerical distance and size effects cannot be caused by the ANS, while the DSS model might be the alternative approach that can explain the frequency-based size effect.

The Dual-Frequency Precipitation Radar (DPR) on the Core GPM satellite provides spaceborne 3-dimensional observations of the precipitation field and surface rainfall rate with quasi global coverage. The present study evaluates the behavior of liquid precipitation intensity, radar reflectivity factor (ZKu and ZKa) and Drop Size Distribution (DSD) parameters (weighted mean diameter Dm and intercept parameter Nw) of the GPM DPR derived products version 07 from 2014 to 2023. Observations from seven Parsivel disdrometers located in different topographic zones in the Western Mediterranean are taken as ground reference. Four matching techniques between satellite estimates and ground level observations were tested, and best results were found for the so-called optimal comparison approach. Overall, GPM DPR products capture well the variability of the observed DSD at different rainfall intensities. However, overestimation of the mean Dm and underestimation of the mean Nw are observed, being much more sensitive to errors in drop diameters larger than 1.5 mm. Moreover, lowest errors were found for radar reflectivity factor and Dm, and highest for Nw and rainfall rate. In addition, the GPM DPR convective and stratiform classification was tested and it was found a substantial overestimation of stratiform cases compared to disdrometer observations.

This study describes a comparative in vitro study of the toxicity behavior of zinc oxide (ZnO) nanoparticles and micro-sized particles. The study aimed to understand the impact of particle size on ZnO toxicity by characterizing the particles in different media, including cell culture media, human plasma, and protein solutions (bovine serum albumin and fibrinogen). The study used various techniques such as atomic force microscopy (AFM), transmission electron microscopy (TEM), and dynamic light scattering (DLS) to characterize the particles and their interactions with proteins. Hemolytic activity, coagulation time, and cell viability assays were used to assess ZnO toxicity. The results highlight the complex interactions between ZnO NPs and biological systems, including their aggregation behavior, hemolytic activity, protein corona formation, coagulation effects, and cytotoxicity. Moreover, the study indicates that ZnO nanoparticles are not more toxic than micro-sized particles, and the 50 nm particles resulted in general the least toxic. Furthermore, the study found that at low concentrations, no acute toxicity was observed. Overall, this study provides important insights into the toxicity behavior of ZnO particles and highlights that no direct relationship between nanometer size and toxicity can be directly attributed.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Background: Screening for postpartum depression can lower prevalence and ensure that mothers get adequate treatment and support. Yet, few practitioners screen.The present article is a brief review on barriers to screening and two screening scales that are validated for perinatal women. Findings: Despite recommendations from health organizations, most new mothers are not screened for depression. Providers cite lack of time, opening “Pandora’s box,” and lack of resources for mothers who screen positive as reasons for why they do not screen. The Edinburgh Postnatal Depression Scale and the Patient Health Questionnaires are brief screening scales that have been validated for new mothers and are widely available.Conclusions: Screening is the necessary first step to identifying new mothers who are depressed. Practitioners who screen need a clear plan, and to know how to access available community resources, so they will know what to do when a mother screens positive.

The utilization of inertial measurement units (IMUs) as wearable sensors is proliferating 1 across various domains such as healthcare, sports, and rehabilitation. This expansion is driven by 2 the continuous improvement of sensor technology to accommodate specific operational demands. 3 This paper introduces the development of a configurable wearable device capable of capturing both 4 high-frequency and low-frequency signals, tailored for a wide range of monitoring applications.Our 5 focus is on a comprehensive evaluation of the device in terms of deviation, noise levels, and precision. 6 We present initial findings that demonstrate the device’s robust performance, and put on the spotlight 7 the most critical optimizations needed to improve the device to reach the goal of a smart general-use 8 unit for human motion monitoring.

Starting with unitary quantum dynamics, we investigate how to add quantum measurements. Quantum measurements have four essential components: the furcation, the witness production, an alignment projection, and the actual choice decision. The first two components still lie in the domain of unitary quantum dynamics. The decoherence concept explains the third contribution. It can be based on the requirement that witnesses reaching the end of time on the wave function side and the conjugate one have to be identical. In this way, it also stays within the quantum dynamics domain. The surjection hypothesis explains the actual choice decision. It is based on a two boundary interpretation applied to the complete quantum universe. It offers a simple way to reduce these seemingly random projections to purely deterministic unitary quantum dynamics, eliminating the measurement problem.

In order to enhance the accuracy of the relative velocity measurement for the Mars explorer formation flight, we develop a relative velocity measurement method. In this method, the spectrometers at two Mars explorers are adopted to measure the starlight frequency shift and to estimate the velocity with respect to the star. Unfortunately, the instantaneous velocity of star can not be predicted accurately, which results in a large error in the velocity measurement. The difference of these two velocities, which does not include the proper motion of star, is the relative velocity between a pair of Mars explorers at the direction of the star. However, this navigation method can not work alone because of unobservability. To make the navigation system observable and improve the accuracy of both absolute and relative navigation for the Mars explorer formation flight, we combine it with X-ray pulsar navigation and the inter-satellite links, and propose an autonomous integrated navigation method with observability. In this integrated navigation scheme, the extended Kalman filter is adopted to deal with the relative velocity, the inter-satellite links and the pulse time-of-arrival, and estimate the absolute and relative navigation information for the Mars explorer formation flight. The simulation results demonstrate that both absolute and relative navigation accuracy of the proposed method are higher than that of the pulsar navigation, especially the relative one.

Introduction: Laeverin is an extravillous trophoblast marker playing a significant role in the trophoblast migration. The purpose of this study was to evaluate the association between the amniotic and serum laeverin concentrations at 16-22 weeks of gestation and the fetal and placental ultrasound measurements in healthy, unaffected pregnancies. Materials and methods: This was a prospective cross-sectional study. Pregnant women with singleton pregnancies undergoing amniocentesis were recruited consecutively. Fetal structural malformations and/or aneuploidy were exclusion criteria. Fetal biometric parameters and placental growth/perfusion were measured in 44 high-risk pregnancies who had no pregnancy complication and any other chronic disease. Maternal serum and amniotic levels of laeverin were essayed with sandwich enzyme-linked immunosorbent assay. Results: Serum laeverin levels are decreasing slightly with the maternal age in mid-gestation. Serum laeverin level correlated negatively slightly with head size of the fetus with the gestational length at delivery (β=-0.38, 95% confidence interval (CI) -0.03-0.01), while the amniotic laeverin level correlated strongly with the abdominal circumference of the fetus (β=-0.64, 95% CI: -0.03-0.01). Furthermore, laeverin level in the amnion correlated moderately and positively with the placental volume (β=0.46, 95% CI: 0.01-0.08). Conclusions: Laeverin levels detected in the serum and in the amniotic fluid denotes the fetoplacental growth in uncomplicated high-risk pregnancies.

The fast spread of COVID-19 constitutes a worldwide challenge to the public health, educational, and trade systems, affecting the overall wellbeing of human societies. The high transmission and mortality rates of this virus, and the unavailability of a vaccine or treatment, resulted in the decision of multiple governments to enact measures of social distancing. Thus, it is of general interest to consider the validity of the proposal for keeping a social distancing of at least 2 m from other persons to avoid the spread of COVID-19. The exposure to the bioaerosol can result in the deposition of the pathogen in the respiratory tract of the host causing disease and an immunological response. In the atmospheric context, the work evaluates the effect of aerodynamic diameter (size) of particles in carrying RNA copies of the novel coronavirus. A SARS-CoV-2 carrier person talking, sneezing, or coughing at distance of 2 m can still provide a pathogenic bioaerosol load with submicron particles that remain viable in air for up to 3 hours for exposure of healthy persons near and far from the source in a stagnant environment. The deposited bioaerosol creates contaminated surfaces, which if touched can act as a path to introduce the pathogen by mouth, nose, or eyes and cause disease.

We investigate the physics of a medium-size quantum particle' gases, of the order of hundreds or thousands of fermions/bosons (far below the thermodynamic limit $N \, \rightarrow \, 10^{24}$). Appeal to microcanonical ensemble becomes then unavoidable. The so-called statistical complexity is our protagonist. Interesting facts are uncovered, both for fermions and bosons, yielded by statistical quantifiers.

The access to cardiac rehabilitation (CR) is contingent upon physician referrals, yet these are often inadequate, particularly in low-resource settings. This multi-method study aimed to translate, culturally adapt, and validate the Portuguese version of the Provider Attitudes toward CR and Referral (PACRR-P) scale, as well as to identify key factors influencing CR referral in a Latin American context for the first time. The PACRR was translated into Brazilian-Portuguese through a rigorous process involving independent translation, back-translation, and expert panel review to ensure face, content, and cross-cultural validity. A total of 44 Brazilian physicians completed the questionnaire, allowing for an assessment of internal consistency, criterion validity, and convergent validity. The findings confirmed the face, content, and cultural validity of the 20 translated items, with a mean item clarity rating of 4.8/5. The final version included 17 of the original 19 PACRR-P items, with a Cronbach’s alpha of 0.73. Referral rates were significantly associated with specific PACRR-P items, supporting the scale's criterion validity, while correlations with ReCaRe scores further supported convergent validity. The most prominent barriers to referral were a lack of familiarity with CR site locations, absence of a standard referral form, and lack of automatic referral processes. The PACRR's validity and reliability among Portuguese-speaking providers are preliminarily supported.

Objective: To explore the inter-rater reliability of the Measurement Of adherence Via Exercise Demonstration (MOVED) adherence tool. Design: Reliability study of a patient adherence measurement tool.Setting: Simulated physiotherapist-patient consultations. Participants: Sixteen experienced physiotherapists rated patient adherence to exercise. Interventions: N/A Main Outcome Measure: Inter-rater reliability of MOVED.Methods: The MOVED tool consists of two parts. Part one asks patients to self-report their adherence to exercise dose (including number of completed sessions, sets and repetitions in the last seven days). Part two asks patients to demonstrate each exercise. Component scores are totalled to give an overall level of patient adherence to each exercise.Participants were provided with a copy of five physiotherapist-prescribed exercises. Participants were then shown five corresponding video vignettes of simulated physiotherapist-patient consultations where patients were asked to self-report exercise frequency, sets and repetitions and demonstrate each exercise within the context of a consultation. Participants were asked to rate the level of patient adherence to each of the five exercises using the MOVED tool. Inter-rater reliability of MOVED scores was assessed using Intraclass Correlation Coefficient (ICC) and 95% Confidence Intervals. Results: The ICC of part one (self-report) was .90 (95%CI .74-.98), part two (demonstration) was .98 (95%CI .94-.99) and total score was .96 (95%CI .88-.99), demonstrating excellent inter-rater reliability. Conclusion: The MOVED tool, which can highlight whether patients are adhering to exercise technique as well as exercise dose, may provide clinicians and researchers with a more robust measure of exercise adherence when compared with other measures currently available.

Tumor to stroma ratio is a highly debated prognostic factor in the management of several solid tumors and there is no universal agreement on its practicality. In our study we proposed to confirm or dismiss the hypothesis that a simple measurement of stroma quantity is an easy-to-use and strong prognostic tool. We have included 74 consecutive patients with colorectal cancer who underwent primary curative abdominal surgery. The tumors have been grouped into stroma-poor (stroma &lt;10%), medium-stroma (between 10 and 50%) and stroma-rich (over 50%). The proportion of tumor stroma ranged from 5% to 70% with a median of 25%. Very few, only 6.8% of patients had stroma-rich tumors, 4% stroma-poor tumors and 89.2%tumors with a medium quantity of stroma. The proportion of stroma, at any cut-off, had no statistically significant influence on the disease specific survival. This can be explained by the low proportion of stroma-rich tumors in our patient group and the inverse correlation of stroma proportion with tumor grade. The real-life proportion of stroma-rich tumors and the complex nature of the stroma-tumor interaction has to be further elucidated.

Cotton seeds as the main by-product of cotton are not only an important raw material for edible oil and feed but also a source of biofuel. The quality of cotton seeds directly affects cotton planting and is closely related to the yield and fiber quality. However, the molecular mechanism governing cotton seed size remains largely unexplored. This study investigates the regulatory mechanisms of cotton seed size by focusing on two cotton genotypes, N10 and N12, which exhibit notable phenotypic variations across multiple environments. Developing seeds were sampled at various stages (5, 20, 30, and 35 DAP) and subjected to RNA-seq. The temporal pattern clustering and WGCNA on differentially expressed genes identified 413 candidate genes, including these related to sugar metabolism that were significantly enriched in transcriptional regulation. A genetic transformation experiment indicated that the overexpression of the GhUXS5 gene encoding UDP-glucuronate decarboxylase 5 significantly increased seed size, suggesting an important role of GhUXS5 in regulating cotton seed size. This discovery provides crucial insights into the molecular mechanisms controlling cotton seed size, helping to unravel the complex regulatory network and offering new strategies and targets for cotton breeding to enhance the economic value of cotton seeds and overall cotton yield.

Although some alternative metrics have been proposed in classical gravity, the singularity problem remains unresolved perfectly. To satisfy the super-gravitational requirement of a black hole without singularities, we propose some possible finite-size structure to avoid the confused one. In this research, the degenerate Fermi electron gas is first used to reveal that the Fermi electron gas cannot shrink to a point regardless of how much energy it obtains; therefore, the singularity existing at the center becomes very unreasonable. To avoid these problems, a finite-size nucleus of the black hole is proposed and explained by the behaviors of the Fermi electron gas and Fermi neutron gas for this finite-size nuclear model. We construct the Kerr-Newman black hole by using a non-rotating but charged finite-size nucleus, a compact-like star, which is surrounded by counter-rotating and corotating electrons. Based on this model, the super-gravity the same as the one from a black hole is presented, and the speed of light observed at far-away places can be nonzero at the event horizon.

The Finite size Lyapunov exponent (FSLE) has been used extensively since the late 1990’s to diagnose turbulent regimes from Lagrangian experiments and to detect Lagrangian coherent structures in geophysical flows and two-dimensional turbulence. Historically, the FSLE was defined in terms of its computational method rather than via a mathematical formulation, and the behavior of the FSLE in the turbulent inertial ranges is based primarily on scaling arguments. Here we propose an exact definition of the FSLE based on conditional averaging of the finite amplitude growth rate (FAGR) of the particle pair separation. With this new definition, we show that the FSLE is a close proxy for the inverse structural time, a concept introduced a decade before the FSLE. The (in)dependence of the FSLE on initial conditions is also discussed, as well as the links between the FAGR and other relevant Lagrangian metrics, such as the finite time Lyapunov exponent and the second order velocity structure function.

Additive manufacturing (AM) is today’s buzzword—and not only in commercial production. One of the AM techniques produces 3D objects with complex geometry using a laser beam. The relationship between the morphology of individual powder particles and the printing process has not been adequately documented yet. This article presents a detailed microscopic analysis of virgin and reused powder particles of maraging steel. Metallographic observation was performed using a scanning electron microscope (SEM). Detailed analyses of individual particles were carried out using SEM with a focused ion beam (FIB) milling capability. Analyses of elemental distribution and phase distribution were performed using EDS and EBSD, respectively. The findings have led to a better understanding and prediction of defects in additive-manufactured products.

There are no studies that quantitatively compare life histories among scorpion species. Statistical procedures applied to 94 scorpion species indicate that those with larger bodies do not necessarily have larger litters or longer life cycles, opposite to some theoretical predictions.

In this paper we show that the Schwarzschild radius can be extracted easily from any gravitationally-linked phenomena without having knowledge of the Newton gravitational constant or the mass size of the gravitational object. Further, the Schwarzschild radius can be used to predict any gravity phenomena accurately, again without knowledge of the Newton gravitational constant and also without knowledge of the size of the mass, although this may seem surprising at first. Hidden within the Schwarzschild radius are the mass of the gravitational object, the Planck mass (their relative mass), and the Planck length. We do not claim to have all the answers, but this seems to indicate that gravity is quantized, even at a cosmological scale, and this quantization is directly linked to the Planck units. This also supports our view that the Newton gravitational constant is a universal composite constant of the form $G=\frac{l_p^2{c}^3}{\hslash }$ , rather than relying on the Planck units as a function of G. This does not mean that Newton’s gravitational constant is not a universal constant, but that it is instead a composite universal constant that depends on the Planck length, the speed of light, and the Planck constant. Further, $\frac{G\times 1\hspace{0.17em}\mathrm{weight}\hspace{0.17em}\mathrm{unit}}{c^2}=\frac{G}{c^2}$ is the Schwarzschild radius off one weight unit. So G is only needed when we want to use gravity to find the weight of an object, such as weighing the Earth. This is, to our knowledge, the first paper that shows how a long series of major gravity predictions and measurements can be completed without any knowledge of the mass size of the object, or Newton’s gravitational constant. As a minimum we think it provides an interesting new angle for evaluating existing gravity theories, and it may even give us a small hint on how to combine quantum gravity with Newton and Einstein gravity.

One of the most popular techniques for determining electrical properties of material is the free-space measurement technique. With the potential for new applications requiring efficient, accurate and broadband material measurement systems using higher millimeter-wave and terahertz frequencies, the free-space measurement method has received renewed interest. This is mainly due to its simplicity, favorable properties as a non-destructive method, and it allows transmission and reflection measurements without any physical contact with the sample. This paper reviews and discusses state- of-the-art free space material measurement systems, starting with the different measurement techniques available for material characterization, their important concepts, post-processing in determining their properties, and progress towards expanding their use at higher frequencies. Also, this paper reviews dielectric material characterization using the free space method focusing on their application extension towards the higher frequencies. Besides, the algorithms for conversion methods and usage of lens in free space material measurement system was discussed in this paper. Finally, a future perspective on the outlook of this free space method is presented prior to the conclusion.

Acquisition of real-time hydraulic data is an essential component for flood forecasting. However, we frequently face difficulties in obtaining discharge data using classical contact methods during high magnitude floods and for systems experiencing rapid hydro-geomorphological adjustment. Therefore, we developed low-cost, non-contact sensors and platforms that are designed to overcome these difficulties. These advances enable flood flow properties to be monitored at multiple locations across a river catchment, at low-cost, and communicated in near real-time by using an image velocimetry method. This is an optics-based approach for stream flow measurement using commercially available near-infrared digital cameras to acquire video footage in full HD (30fps). Video footage is then subjected to optical flow tracking techniques based on cross-correlation, and feature-based tracking, enabling the displacement rates of detected features (for example natural foam, seeds, woody debris, and turbulent structures) to be computed. This manual provides step by step guidance to install an image-based gauging station. It contains the list of necessary components, the calibration process of a new camera and the assembly procedure of the system.

Introduction and Problem: With conventional mechanical rotation measurement of joints, only static measurements are possible with the patient at rest. In the future, however, it would be interesting to carry out dynamic rotation measurements, for example when walking or doing sports. Therefore, a measurement method with an elastic capacitive measuring system was developed and validated. Material and Methods: The measurement system consists of a capacitive strain gauge connected to a flexible printed circuit board. The electronics on the printed circuit board are used for data acquisition and transmission. When the sensor strip is stretched, the distance between the fingers of the strain gauge changes and with it the capacitance. Consequently, the strain can be measured via the change in capacitance. The measurement system is taped to the knee with the sensor on the skin in the direction of the anterolateral ligament (ALL). The bottom of the sensor (silicone) and the bottom of the circuit board are in contact with the knee surface. The sensor must be attached to the knee without pre-stretching The system is validated with an in vivo test on 11 patients. For this purpose, the internal rotational laxity of the knee was tested on healthy volunteers and the results compared with the measurements on the static measuring device (Laxitester). The subjects are placed in the supine position. First the left and then the right leg is clinically examined one after the other and documented using an examination form. Exclusion criteria are the presence of a pathological ligament findings in the area of the collateral/cruciate ligaments, previous knee operations or limitations in the range of motion. The distal thigh rests on a support bench on which a knee joint flexion of 30° is set by height adjustment. The femoral condyles are secured against rotation in the positioning aid by posts. This also prevents internal rotation and displacement of the thigh. The foot is strapped into the holding device without shoes. The second toe beam is centered using an adjustable side clamp on the medial and lateral edge of the foot. Dorsiflexion is set at 2 Nm with a torque meter, in accordance with previous studies, to rule out rotational laxity in the ankle. The strain gauge sensor is taped to Gerdii’s tubercle in the course of the antero-lateral ligament below the lateral epicondyle of the thigh. Then, in three repeated measurements, the internal rotation of the foot and thus the lower leg is measured with a torque of 2 Nm. The change in length of the stretch mark is compared with the measured internal rotation angle in the static measuring device (Laxitester). Results: A significant difference between the sexes was found in the internal rotation range of the knee (p=0.003). The range of rotation was greater for female participants than for male participants. Regarding the measured length change values, the measurements presented showed an individual result for each participant, which tended to decrease with increasing internal rotation angle, with no age or gender differences being observed. The stiffness of the strain gauge was in the linear range for all measurements, within the first 20% strain of the sensor. The differences determined do not result from a different stretching of the sensor, but from individual differences between the test persons. The comparison between length change and internal rotation angle of the knee showed a strong positive correlation (r=1, p&lt;0.01). Conclusion: Elastic capacitive strain gauges can be used to reliably measure the internal rotation angle of the knee joint. This will allow dynamic measurements in the future.

Our study aimed to identify predictors for the effectiveness of tumor regression in lung cancer patients undergoing neoadjuvant treatment and cancer resections. Patients admitted between 2016 and 2022 were included in the study. Based on the histology of the tumor, patients were categorized into lung adenocarcinoma group (LUAD), and squamous cell carcinoma group (SQCA). Ninety-five patients with non-small cell lung cancer were included in the study. Fifty-eight (61.1%) and 37 (38.9%) patients were included in the LUAD and SQCA groups, respectively. Nine (9.5%), 56 (58.9%), and 30 (31.6%) patients were categorized with a tumor regression score of I, II, and III respectively. In multivariable analyses, histology of the primary tumor (SQCA), lymph node size in the preoperative CT scan (>1.7cm) and absolute tumor size reduction after neoadjuvant treatment (>2.6 cm) independently predict effectiveness of tumor regression (OR, [95% Confidence interval, p-value] of 6.88 [2.40-19.77, p70 years, extended resection >one lobe, and tumor recurrence or metastasis were identified as significant independent predictors of reduced overall survival. Assessment of tumor size before and after neoadjuvant treatment might help to identify high-risk patients with decreased survival and to improve patient management and care.

To solve the problem of complex sensor installation and easy damage in contact displacement measurement, a non-contact measurement method of brace displacement in bridge swivel construction based on binocular vision is proposed in this study. Combined with monitoring data in a swivel construction interchange project, binocular vision system was compared and analyzed with the traditional displacement meter and total station. Results showed that force versus displacement variation plots were obtained by binocular visual measurement in the weighing test, the inflection point can be clearly distinguished, and the position of the inflection point was the same as that of the displacement meter; monitoring data of binocular vision measurement and total station were compared and analyzed in the bridge swivel process, the average error was no more than 0.18 mm, the maximum error was no more than 0.42 mm, and the standard deviation was no more than 0.12. The method proposed in this study can be used as an alternative to displacement meter and total station measurement methods in bridge swivel construction, the problem of complex sensor installation and easy damage is solved in brace displacement measurement, equipment and labor costs can be effectively saved.

The results of the study of the influence of the size of cylindrical samples of A5N aluminum on the time and rate of their cooling are presented. According to experimental data, the temperature dependence of the heat transfer coefficient for pure metals is calculated. It revealed that the process of cooling of the aluminium and its alloys has a relaxation behavior. It has found that the main mechanisms of natural air cooling are convection heat transfer and radiation. The characteristic cooling time due to radiation is less than due to convection. The contribution of thermal radiation is noticeable at high temperatures. It was found that the characteristic times of cooling due to radiation and convection increase with increase in volume to area ratio of the sample.

The angular diameter is the angle subtended by a generic object – an apple or a star – to the eye of an observer, and it describes how large the object appears from a given viewpoint. The angular diameter represents a powerful tool for distance calculations starting from a directly measurable information and it finds application in several contexts varying from cosmography to architecture. In this article, the author proposes a novel equation to calculate the apparent diameter of whatever object. This equation defines the relationship between the object’s apparent diameter with respect to the travelled distance starting from the initial distance R₀ at which the observed object is located. Based on the preliminary tests conducted, the model seems to faithfully portray this relation with respect to measured values, also at the astronomical scale, thus considering the Earth-Moon distance, where, the absolute error detected is about 0.56%. Tests highlight also a dependency between the results accuracy and the measurement conditions suggesting a high level of sensibility linked to the initial magnification effect produced by the retina or the artificial lens employed.