The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Non-invasive continuous health monitoring has become feasible with the advancement of biosensors. While monitoring certain biomarkers such as heart rate or skin temperature are now at certain maturity, monitoring molecular biomarkers is still challenging. Progress has been shown in sampling, measurement and interpretation of data towards non-invasive molecular sensors that can be integrated in daily wearable items. Towards this goal, this paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. In controlled experiments, we have shown the variation of glucose concentration in water can be wirelessly detected by tracking the resonant frequency of the embroidered sensors. The current sensors operate at 1.8GHz–2GHz and respond to the change of glucose concentration with a sensitivity of 0.17 MHz/(mg/dl). The embroidered IDT-based sensors with wireless sensing will be a new measurement modality for molecular wearable sensors. The establishment of a wireless sensing mechanism for embroidered IDT-based sensors will be followed by investigation of sweat for molecular detection. This will require adding functionalities for sampling and interpretation of acquired data. We envisage the embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Protection suit is vital for fireman’ safety. Traditional protection suit just physically protects fireman from empyrosis, but can not locate the body injury position from the impact debris. Herein, we present a wearable impact debris positioning system for fireman protection suit alarming based on accelerometer array. The wearable piezoelectric accelerometers with distribute regularly on the suit to detect the vibration on different body parts, which is conducive to positioning injured body parts. In addition, the injured parts can be displayed on the dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11ms attributing to smart signal processing method. This work provides a reliable and smart method for locating and assessing the body injury position from the impact debris, which is significant for fire disaster commander to rescue injured fireman in time.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

Introduction: Anterior Lumbar Interbody Fusion (ALIF) and Posterior Spinal Fusion (PSF) play pivotal roles in restoring lumbar lordosis in spinal surgery. Debates persist between combined single-position surgery and traditional prone-position PSF for optimizing segmental lumbar lordosis. Research Question: The study investigates the impact of performing ALIF in the supine position followed by PSF in the prone position on segmental lumbar lordosis. Material and Methods: A cohort of 59 patients underwent ALIF and PSF at a single institution. Preoperative, post-ALIF supine, and post-PSF prone Cobb angles were assessed using x-ray imaging. Statistical analyses, including one-way repeated measures ANOVA and Post-hoc analyses with Bonferroni adjustment, were employed for mean comparisons within subjects. Results: The mean Cobb angle for the entire cohort showed significant variations over different time points (p).

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

In this digital era, laundry applications come as an innovative solution to meet the laundry needs of modern people who often have busy schedules and limited time. This research aims to make a significant contribution to our broader understanding of how digital innovations can revolutionize mundane tasks. This research uses the Waterfall model, which is one of the methods in the Software Development Life Cycle (SDLC). The development process begins with the Requirement Analysis stage, where application requirements and specifications are collected and thoroughly analyzed to ensure that the developed application will meet user expectations. After that, the System Design stage is conducted, where the application architecture, user interface design, and database structure are designed in detail to ensure conformity with the previously identified needs.The next stage is Implementation, where program code is written and application features are developed according to the design that has been made. The final stage is Integration and Testing, where all application components are combined and tested thoroughly to detect and fix any errors or bugs that may exist. The results of this study produced a web-based shuttle laundry service application using the Laravel framework called "All Fresh Laundry". This application can order clothes washing services according to its membership, where there are 3 types of membership based on price and of course have different benefits. In addition, the testing phase of this application using black box testing shows that all menu features function properly according to their functions. Each component of the "All Fresh Laundry" app was thoroughly tested to ensure that no errors or malfunctions occurred. The results of this testing make it clear that every feature, from online ordering to laundry status tracking, works well and meets the specifications that have been set, so that this application can provide an optimal and reliable user experience.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

Agriculture contributes towards South African economy, but this sector is highly vulnerable to risks imposed by climate change. Smallholder maize farmers are specifically susceptible to climate change impacts. Maize crop plays a crucial role in the country's food security as it is considered a stable food for households and source of feed for livestock. The study aimed to analyze the socio-economic factors influencing smallholder maize farmers’ willingness to adopt climate-smart agriculture. It was conducted in three different areas due to their specific agro-ecological zones. Multipurpose research design was used to gather data, and multistage random sampling to choose the study areas. Subsequently, 209 purposively selected farmers were interviewed face-to-face using structured questionnaires and focus discussion groups. Descriptive statistics and Double-hurdle regression model were used to analyze the data. Descriptive results indicated that 81%, 67%, and 63% farmers were willing to adopt CSA in Ga-Makanye, Gabaza, and Giyani, respectively. Empirical results from the first and second hurdles of the regression analysis showed that farmers’ education, crop diversification, information about CSA positively influenced the decision to adopt CSA while household size and agricultural experience negatively influenced the decision to adopt CSA. It is recommended that the Department of Agriculture, Land Reform, and Rural Development should provide CSA workshops and educational programs to farmers to enhance their knowledge and decision-making processes regarding adaptation strategies.

Traditional agricultural extension services rely on extension workers, especially in countries with large agricultural areas. In order to increase adoption of sustainable agriculture, the recommendations given by such services must be adapted to local conditions and be provided in a timely manner. The AgroTutor mobile application was built to provide highly specific and timely agricultural recommendations to farmers across Mexico and complement the work of extension agents. At the same time, AgroTutor provides direct contributions to the United Nations Sustainable Development Goals, either by advancing their implementation or providing local data systems to measure and monitor specific indicators such as the proportion of agricultural area under productive and sustainable agriculture. The application is freely available and allows farmers to geo-locate and register plots and the crops grown there, using the phone’s in-built GPS, or alternatively, on top of very high-resolution imagery. Once a crop and some basic data such as planting date and cultivar type have been registered, the app provides targeted information such as weather, potential and historical yield, financial benchmarking information, data-driven recommendations as well as commodity price forecasts. Farmers are also encouraged to contribute in-situ information, e.g., soils, management, and yield data. The information can then be used by crop models, which, in turn, would send tailored results back to the farmers. Initial feedback from farmers and extension agents has already improved some of the app’s characteristics. More enhancements are planned for inclusion in the future to increase the app’s function as a decision support tool.

As people grow a custom to effortless outdoor navigation there is a rising demand for similar possibility indoors as well. Unfortunately, indoor localization, being one of the necessary requirements for navigation, continues to be problem without a clear solution. In this article we are proposing a method for an indoor positioning system using a single image. This is made possible using small preprocessed database of images with known control points as the only preprocessing needed. Using feature detection with SIFT algorithm we can look through the database and find image which is the most similar to the image taken by user. Pair of images is then used to find coordinates of database image using PnP problem. Furthermore, projection and essential matrices are determined allowing for the user image localization ~ determining the position of the user in indoor environment. Benefits of this approach lies in the single image being the only input from user and no requirements for new onsite infrastructure and thus enables a simpler realization for the building management.

The use of mobile phones has increased dramatically among drivers in multiple countries in the past few years. The primary objective of this study was to measure the prevalence of cell phone use while driving in Saudi Arabia and to find whether there is a relationship between car accidents and the use of mobile phones while driving. The secondary objective was to explore general knowledge and attitudes toward traffic regulations related to cell phone usage while driving. This is a cross-sectional study conducted among 585 drivers in Saudi Arabia using a self-reported online survey distributed through social media channels. Our results showed that 78.6% of the participants acknowledged that they use the phone while driving. The percentage who reported car accidents involving them or their friends or relatives while using the phone while driving was 43.8%, along with 71.8% mentioning near misses. The percentage of respondents who thought that using a mobile phone while driving had a strong impact on the driver’s ability to drive was 31.5%. This study highlights the importance of raising awareness about risks of using Mobile phones during driving in Saudi Arabia and it recommends harsher penalties to reduce the use of mobile phones while driving.

This study aims to assess using a smartphone app (DecibelX), as a noise measuring alternative to the more costly traditional use of measuring noise levels with a Sound Level Meter (SLM). The study compares the accuracy of the app to readings taken with a SLM and dosimeter, and also evaluates the app’s performance for pure tone and narrow band noise. And a usability study identifies strengths and weaknesses related to usability of the app.

This research proposes a methodology for minimizing losses in transmission lines (LT), considering the reconfiguration of the architecture of the electrical power system (SEP). The implementation of this methodology redirects the power flow with optimal switching through its LTs to guarantee the stability of the voltage, angle, frequency, and power balance to minimize losses that affect the reliability and quality of the system. Optimal transmission switching (OTS) allows various types of analysis to be carried out, where the loadability of the lines, response times, and operating costs, among others, can be improved. This article proposes to minimize the losses in the transmission lines with the OTS by using AC power flows as a mixed integer nonlinear problem (MINLP). Several test scenarios evaluate the method’s effectiveness, determining the optimal topology for corrective control that optimizes power flows in different situations. It has been proven that this approach reduces losses compared to a base case by 99%, even in the face of N-1 or random contingencies, without losing load, maintaining the same active power dispatch, and finally verifying a strategic increase in dispatch of reactive power to maintain operating parameters within stable limits.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

Excessive cell phone use contributes to distracted driving, may increase risk for automobile accidents, and a minority of mobile phone users exhibit behaviors consistent with technological addiction. The purpose of this study was to determine whether cell phone beliefs and behaviors could be changed by a brief educational encounter. The Theory of Reasoned Action provided a lens for viewing attitudes and behavior. A one-week pre-post design with a thirty-day follow-up was used with participants (N = 215, 67.0% female, age = 20.0 + 1.6) assigned to a peer led intervention or comparison groups. The intervention included cell-phone educational materials. A short index of cell phone behavior was developed which showed good internal consistency with a Cronbach’s alpha of .81. The intervention group “agreed” or “strongly-agreed” more than the comparison group on five of the seven areas of cell phone beliefs and behaviors ( p < 0.05, item Cohen’s d = .32 to .47, total d = .50) at one-week following receipt of informational materials. We conclude that attitudes and behaviors regarding cell phones are malleable and susceptible to change in young-adults following a brief psychoeducational intervention.

This article summarizes the results of a research conducted to create an intelligent platform supporting small farmers growing vegetables. In Bulgaria, many farmers use relatively small areas for their production. Considering this situation, the platform is designed for regional use, trying to make maximum use of the specific climatic features of the monitored microdistrict. Consequently, special attention is paid to the possibilities of adapting the platform to the specific environment in which the observed plants grow. Thus, the platform is implemented as an agent-oriented system providing needed flexibility. The core of the platform is a personal assistant, which is responsible for tracking the vegetation cycle of the monitored crop and, upon detection of anomalies, preparing warnings to the farmer. The general architecture of the platform is also presented. In a distributed knowledge base, agriculture-specific knowledge are stored. Furthermore, a standardized interface for receiving data from the sensor networks located in the production areas is briefly described. Currently, the platform is being tested for monitoring four varieties of tomatoes grown on the territory of the national research center for potato breeding. Special attention is paid to the measurements carried out. Conclusions have been drawn that will help improve the platform.

Adolescents spend an increasing amount of time on mobile phones. The aim of this study was to assess the relationship between duration of mobile phone use and insomnia and depression in senior high school students. The cross-sectional study was conducted on 295 senior high school students in Japan. Mobile phones were owned by 98.6% of students; 58.6% of students used mobile phones for more than 2 h daily and 10.5% used them for 5 h daily. The risk of insomnia was significantly high in students who used mobile phones for 5 h or more (OR: 3.89 [95% CI: 1.21-12.49]). There was no significant association between depression and duration of mobile phone use. However, individuals who spent 120 min or more using mobile phones for social network services (OR: 3.63 [1.20-10.98]) and online chats (OR: 3.14 [1.42-6.95]) were at risk for depression. Excessive mobile phone use is associated with unhealthy sleep habits and insomnia. Moreover, the excessive use of the social network services and online chats are related to depression rather than duration of mobile phone use. Adolescents should use mobile phones appropriately to avoid sleep disturbances and the impairment of mental health.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

Whereas bisexuality, as it existed in modernity, has been described as a ‘floating signifier', one that was problematically conflated with gender and intersex bodies, the articulation of bisexuality is now experiencing a discursive resurgence in spaces and platforms online. Through a deliberately disparate comparison between Virginia Woolf’s modernist writing and the discussions of bisexuality on the video-sharing social networking service TikTok, this essay presents a reflective reassessment of how far bisexual representation in the popular imagination has progressed and by extension, evaluate extant limitations. To realize these ambitions, I compare the reception of sexology (the new science of sexuality) in ‘high’ modernist literature with a post-modern demographic whose bisexuality is articulated in the 2020s online via TikTok’s towards what I would demarcate as a post-queer theory user base. This essay is not intended as an overview of the advancements made in psychoanalytic institutions about bisexuality nor does it set out to comment on the refinement of bisexuality’s aestheticization through time. Instead, it uses these two temporally specific moments in the cultural zeitgeist to compare and contrast how differently two different demographics articulate bisexuality, both as a written mode in modernism and as a visual apparatus online. This is less a critique of bi-erasure, but an interrogation of why and how bisexual representation, as an aestheticized subjectivity that compromises romantic, spiritual, and erotic desires for bodies of all genders, continues to be problematically restrictive.

For the purpose of improve the sustainability of products sold in the EU, Digital Product Passports is a mandatory solution. These passports would systematically gather information about products, such as detailing the materials involved to aid recycling and remanufacturing efforts, or recording the emissions produced throughout the manufacturing process. The overall goal is the establishment of a circular economy in the EU. Current research on Digital Product Passports is focused on collating content for sector-specific applications. However, achieving sustainability goals through Digital Product Passports will require new methods and technical solutions for digital collaboration between supply chain participants, especially in the manufacturing sector. Collaborative work on Digital Product Passports requires trust and traceability in data and access management to ensure privacy over the data contained. One way to enable this securely and confidentially is through the use of blockchain technology, in which stored data cannot be concealed, which is key to the traceability of digital product data documentation. This paper therefore presents a concept for the implementation of generically applicable cross-industry blockchain-based digital product passports. To this end, generic supply chain processes have been abstracted and condensed into the architecture of smart contracts. Great attention is paid to the establishment of traceability as well as privacy through the selection of the blockchain technology Secret Network in combination with Gaia-X functionalities. An illustrative use case for digital product passports in manufacturing is used to demonstrate the applicability of the presented concept. In this use case information about the digital nameplate and carbon footprint is exchanged securely and confidentially in a multi-tenant supply chain network based on the Industry 4.0 infomation model of the Asset Administration Shell.

In California, water is a perennial concern. As competition for water resources increases due to growth in population, California’s tree nut farmers are committed to improving the efficiency of water used for food production. There is an imminent need to have reliable methods that provide information about the temporal and spatial variability of crop water requirements, which allow farmers to make irrigation decisions at field scale. This study focuses on estimating the actual evapotranspiration and crop coefficients of an almond and pistachio orchard located in Central Valley (California) during an entire growing season by combining a simple crop evapotranspiration model with remote sensing data. A dataset of the vegetation index NDVI derived from Landsat-8 was used to facilitate the estimation of the basal crop coefficient (Kcb), or potential crop water use. The soil water evaporation coefficient (Ke) was measured from microlysimeters. The water stress coefficient (Ks) was derived from airborne remotely sensed canopy thermal-based methods, using seasonal regressions between the crop water stress index (CWSI) and stem water potential (Ystem). These regressions were statistically-significant for both crops, indicating clear seasonal differences in pistachios, but not in almonds. In almonds, the estimated maximum Kcb values ranged between 1.05 to 0.90, while for pistachios, it ranged between 0.89 to 0.80. The model indicated a difference of 97 mm in transpiration over the season between both crops. Soil evaporation accounted for an average of 16% and 13% of the total actual evapotranspiration for almonds and pistachios, respectively. Verification of the model-based daily crop evapotranspiration estimates was done using eddy-covariance and surface renewal data collected in the same orchards, yielding an r² >= 0.7 and average root mean square errors (RMSE) of 0.74 and 0.91 mm day^-1 for almond and pistachio, respectively. It is concluded that the combination of crop evapotranspiration models with remotely-sensed data is helpful for upscaling irrigation information from plant to field scale and thus may be used by farmers for making day-to-day irrigation management decisions.

Smart manufacturing encompasses a category of manufacturing that employs computer-integrated capabilities and technologies to enhance supply chain optimization, production efficiency, and recyclability. Yet limited studies have been conducted to optimize these prospects from the perspective of low resource countries where such innovative studies have not been adequately explored. This paper aims to examine the implications of smart manufacturing practices (Smart Procurement, Smart Supply Chain, Smart Production Planning and Control, Automation and Industrial Robot, and Supply Chain Configuration) on pro-environmental behaviour and develop a baseline moderated mediation model to explain the relationship between smart manufacturing and pro-environmental behaviour with a role of green dynamic capability, and environmental orientation. This study is anchored on quantitative research approach, deductive reasoning, and explanatory design. Cross – sectional survey data have been obtained from 382 manufacturing companies in Ghana. Our hypotheses have been tested using Structural Equation Modelling and SMART-PLS version 3.8.9. The study has revealed that smart manufacturing practices significantly and positively relate to pro-environmental behaviour. Moreover, green dynamic capability and environmental orientation moderate the relationship between smart manufacturing and pro-environmental behaviour. The implications of the study include the emergence of a baseline model to guide policymakers, practitioners, and academicians to explain the relationship between smart manufacturing and sustainable manufacturing in the context of developing countries. Again, the social implication of the study includes the realisation of decent job and economic growth, responsible consumption and production as well as actions taken to combat climate change.

This paper describes a system that is used to gather data from Smart Home sensors measuring energy consumption, analyze and predict future consumption by using machine learning algorithm for prediction. It focuses on the architecture of the system as well as the need for such system to exist in practice – why the consumption should be measured at all and how that measurement can be put to good use for achieving energy efficiency.

This paper describes the proposal and development of a proof of concept (PoC) for a data logger system designed for operation and fault detection in bench testing of combustion engines. The main objective was to develop a data logger system that collects data on vibration, sound, temperature, and CO2 levels to identify ignition and combustion faults, thereby contributing to reducing greenhouse gas emissions (GHG). The paper presents (i) the proposal and development and (ii) the open-source code: proof of concept for a data logger system focused on detecting faults and monitoring the operational condition of benchtop combustion engines. The results indicate the feasibility of the PoC for data acquisition and dataset creation for Research and Development purposes.

Incorrect sitting posture, characterized by asymmetrical or uneven positioning of the body, often leads to spinal misalignment and muscle tone imbalance. Prolonged maintenance of such postures can adversely impact well-being and contribute to the development of spinal deformities and musculoskeletal disorders. In response, smart-sensing chairs equipped with cutting-edge sensor technologies have been introduced as a viable solution for real-time detection, classification, and monitoring of sitting postures, aiming to mitigate the risk of musculoskeletal disorders and promote overall health. This comprehensive literature review evaluates the current body of research on smart-sensing chairs, with a specific focus on the strategies used for posture detection and classification, as well as the effectiveness of different sensor technologies. A meticulous search across MDPI, IEEE, and Google Scholar databases yielded 34 pertinent studies that utilize non-invasive methods for posture monitoring. The analysis reveals that Force Sensing Resistors (FSR) are the predominant sensors utilized for posture detection, whereas Convolutional Neural Networks (CNN) and Artificial Neural Networks (ANN) are the leading machine learning models for posture classification. However, it was observed that CNNs and ANNs do not outperform traditional statistical models in terms of classification accuracy, due to constrained size and lack of diversity within training datasets. These datasets often fail to comprehensively represent the array of human body shapes and musculoskeletal configurations. Moreover, this review identifies a significant gap in the evaluation of user feedback mechanisms, essential for alerting users to their sitting posture and facilitating corrective adjustments.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

This paper formulates the performance evaluation of cloud services as a multicriteria group decision making problem, and presents a fuzzy multicriteria group decision making method for evaluating the performance of cloud services. Interval-valued intuitionistic fuzzy numbers are used to model the inherent subjectiveness and imprecision of the performance evaluation process. An effective algorithm is developed based on the technique for order preference by similarity to ideal solution method and the Choquet integral operator for adequately solving the performance evaluation problem. An example is presented to demonstrate the applicability of the proposed fuzzy multicriteria group decision making method for solving the multicriteria group decision making problem in real world situations.

The use of mobile devices facilitates access to knowledge and is at the base of the education of the future. Although the digital society has contributed a number of benefits, however, it has also been associated with worrying behaviours. The study design consisted of a quantitative approach that was descriptive, inferential and ex post-facto in nature. Its purpose was to better understand the opinion of young people regarding mobile phone use and describe dependence deriving from regular use. The sample was formed of 420 students from the Faculty of Education at the University of Granada. Results indicate that mobile phone use has displaced use of other technologies such as the television, and is associated with communication and recreational activities. In addition, a profile was identified for young people at greater risk of developing a dependence on their mobile devices. This profile constituted females, mobile phone users with recreational motives and individuals who exceeded mobile phone use by more than six hours a day. To improve the educational use of mobile phone, prevention and intervention plans must be designed which ensure correct management of this device, taking advantage of the benefits it offers whilst avoiding problems derived from inappropriate use.

The purpose of this article is to present an IoT architecture implemented in an intelligent environment, focusing on the optimization of initial conditions and device management. A general control system was developed using an open-source platform, integrating aWi-Fi network and YAML coding to enable communication and control of the IoT architecture devices. The implementation includes actuators, sensors, and control devices that, through a graphical interface, allow the visualization of the historical record of activities and real-time measurements of connected devices. The design includes specific mechanisms and the analysis of materials through tensile tests on specimens, following the ASTM E8 standard, and deformation test simulations, in which PLA demonstrated better performance compared to materials like ABS and resin. The significance of the implemented IoT system lies in an energy saving of 58% compared to conventional structures. Additionally, the study of response times for network connections showed that using an Ethernet cable resulted in a response time of 1.21 seconds, representing a reduction of 1.65 seconds compared to the second lowest value obtained.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

Research focused on understanding wider systemic factors driving behavioral change is limited with a dominant focus on the role of individual farmer and psychosocial factors for farming practice change, including reducing fertilizer application in agriculture. Adopting a wider systems perspective, the current study examines change and the role that supporting services have on fertilizer application rate change. A total of 238 sugarcane growers completed surveys reporting on changes in fertilizer application along with factors that may explain behavior change. Logistic regressions and negative binomial count-data regressions were used to examine whether farmers had changed fertilizer application rates and if they had, how long ago they made the change, and to explore the impact of individual and system factors in influencing change. Approximately one in three sugarcane growers surveyed (37%) had changed the method they used to calculate fertilizer application rates for the cane land they owned/managed at some point. Logistic regression results indicated growers were less likely to change the basis for their fertilizer calculation if they regarded maintaining good relationships with other local growers as being extremely important, they had another source of off-farm income, and if they had not attended a government-funded fertilizer management workshop in the five years preceding the survey. Similar drivers promoted early adoption of fertilizer practice change; namely, regarding family traditions and heritage as being unimportant, having sole decision-making authority on farming activities and having attended up to 5 workshops in the five years prior to completing the survey. Results demonstrated the influence of government-funded services to support practice change.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

Fires in houses are inevitable and they cause loss of life and major repair costs for the damage structure and contents. There is a clear need to prevent its ignition and spread to adjacent areas. This article presents the steps taken, namely: contacts, data collection, tests, analysis and conclusions regarding the accident resulting from the outbreak and spread of a fire, on December 25, 2020, in a traditional Portuguese house in Arganil, Portugal. The owners and the court requested to carry out an expert opinion by a person with specialized technical-scientific knowledge, which led to this work as an expert. the work consists of carrying out observations and data analysis. Then, the observed and analysed data were laboratory tested in order to consistently identify characteristics that lead to the ignition and propagation of the fire. This work identified construction problems, materials used and heat sources that are responsible for the accident. The conclusions may be used to avoid future incidents or accidents with houses of same construction type.

In an era marked by swift technological progress, the pivotal role of Artificial Intelligence (AI) is increasingly evident across various sectors, including local governments. These governmental bodies are progressively leveraging AI technologies to enhance service delivery to their communities, ranging from simple task automation to more complicated engineering endeavours. While more and more local governments are adopting AI, it is imperative to understand the functions, implications, and consequences of AI. Despite the growing importance of this domain, a significant gap persists within the scholarly discourse. This study strives to bridge this void by exploring the applications of AI technologies within the context of local government service provision and using this inquiry to generate lessons and best practices for similar smart city initiatives. Through a comprehensive grey literature review, we analysed 262 real-world AI implementations across 170 local governments worldwide. The findings underscore several key points: (a) There has been a consistent upward trajectory in the adoption of AI by local governments over the last decade; (b) Local governments from China, the US, and the UK are at the forefront of AI adoption; (c) Among local government AI technologies, Natural Language Processing and Robotic Process Automation emerge as the most prevalent ones; (d) Local governments primarily deploy AI across 28 distinct services; (e) Information management, back-office work, and transportation and traffic management are leading domains in terms of AI adoption. This study enriches the extant body of knowledge by providing an overview of existing AI applications within the sphere of local governance. It offers insights for smart city policymakers and decision-makers considering the adoption, expansion, or refinement of AI technologies in urban service provision. Additionally, it underscores the importance of using these insights to guide the successful integration and optimisation of AI in future smart city projects, ensuring they meet the evolving needs of communities.

This publication aims to create 4K UHD video sequences with a specific focus on smart cities and transport. The created database will be accessible to all experts in the field and can be further used for research purposes. All reference video sequences will be transcoded into different quality settings. The resolution, compression standard, and bitrate will be changed. The work will aim to find out the best combination of video parameters from the measured values. Thanks to the overall evaluation, we will ensure for each single video sequence the quality with the best experience for the providers that will offer the service. The database will also be available with its objective and subjective ratings, with dynamicity information characterized by spatial and temporal information. After, It will be possible to compare the results of the subjective evaluation of a selected sample of our respondents with the work of other researchers who can evaluate with a different sample of evaluators.

The Metaverse of Things (MoT) is an advanced technology that has the potential to revolutionise urban living in the present era. This article explores the advantages, uses, and transformative outcomes of MoT in smart cities. The covered subjects encompass sustainability, urban planning, citizen participation, infrastructure management, and various more. MoT integrates the Internet of Things (IoT) with metaverse technologies. The ultimate objective is to develop virtual environments that are highly interactive, interconnected, and immersive while maintaining a high level of fidelity to reality. The IoT utilises virtual reality (VR), augmented reality (AR), and other digital technologies to gather data, facilitate communication, and automate certain processes, thereby enhancing several elements of urban living. It is all a component of the metaverse. The IoT will bring about a profound transformation in the way cities gather and utilise data to enhance services and optimise efficiency. Cities that can efficiently distribute this data can enhance public safety, optimise energy usage, regulate traffic, and manage waste properly. MoT apps that utilise immersive technologies and the IoT can be used to generate more intelligent and captivating cityscapes. The implementation of MoT can greatly enhance the quality of life for residents of smart cities through improvements in transportation, healthcare, education, and community engagement. The study's author examined how smart cities utilise the IoT to enhance the daily experiences of their inhabitants. This study examines the technical structure, possible advantages, and difficulties of implementing MoT in urban settings, aiming to enhance the resilience, responsiveness, and adaptability of cities. The findings emphasise the importance of robust legislative frameworks, stringent security requirements, and well-developed infrastructure to facilitate the extensive use of MoT technology. These factors are crucial for establishing a highly interconnected and efficient urban environment.

Ice formation on aircraft surfaces poses significant safety risks, and current detection systems often struggle to provide accurate, real-time predictions. This paper presents the development and comprehensive evaluation of a smart ice control system using a suite of machine learning models. The system utilizes various sensors to detect temperature anomalies and signal potential ice formation. We trained and tested supervised learning models (Logistic Regression, Support Vector Machine, Random Forest), unsupervised learning models (K-means clustering), and neural networks (Multi-Layer Perceptron) to predict and identify ice formation patterns. Experimental results demonstrate that our smart system, driven by machine learning, accurately predicts ice formation in real-time, optimizes de-icing processes, and enhances safety while reducing power consumption. This solution holds the potential for improving ice detection accuracy in aviation and other critical industries requiring robust predictive maintenance.

Presence detection is essential in many applications, including smart homes, office automation, and public space management. Traditional technologies like infrared sensors and cameras frequently encounter obstacles due to privacy concerns, high costs, and complexity. The study provides a novel way to detect presence based on Wi-Fi signals and machine learning algorithms, utilizing the ESP8266 microcontroller. The suggested system attempts to reliably detect the presence of people in a given place by evaluating fluctuations in Wi-Fi signal strength and patterns. The theoretical basis of this strategy is investigated, including the ESP8266’s capabilities for Wi-Fi data gathering and the use of machine learning methods for data analysis. The methodology includes data collecting with the ESP8266, preprocessing, feature extraction, and training and evaluating machine learning models. This system’s potential uses include smart home automation, office occupancy tracking, and crowd management in public settings. The paper also discusses potential issues such as signal interference, data privacy concerns, and the limitations of Wi-Fi detection. Future work is also mentioned, including the suggested system’s installation and testing and enhancement proposals to improve accuracy and scalability. This research aims to provide a cost-effective, non-intrusive, and scalable presence detection system by harnessing the power of Wi-Fi signals and machine learning, enhancing intelligent environments

As technology advances, people are increasingly adopting IoT (Internet of Things) devices in smart cities. These devices are equipped with sensors that are connected everywhere, from energy infrastructure and transportation to telecommunications, health and human services, waste management, public safety, and more. People want to access sensor data anytime and everywhere to make better decisions and improve their lives. To achieve this, a sensor integration model has been developed where multiple sensors are integrated under one gateway to manage and share sensor data. However, effective sharing of sensor data requires data security, privacy, confidentiality, fairness, effective architectural design, and low communication and computation costs. These issues need to be addressed in the sensor integration model in smart cities. Existing storage models face challenges in managing sensor data effectively. To overcome these issues and hurdles, a data storage framework leveraging blockchain technology has been proposed within the sensor integration model. This framework ensures data security, privacy, confidentiality, and a fair and transparent financial model, all while minimizing communication and computation costs.

The goal of the paper is to investigate the expected participation and mentality of smart citizens in smart cities. The key question is the role of the human factor in smart environments globally studied through a research corpus of the mainstream summaries, trend reports, white papers and visions of business – governmental – university research co- operations. Foremost, a short review of the changing scholarly trends is presented as a theoretical framework. Concerning its key ideas, the corpus based findings are recapped and analysed by content networks and the most referred city strategies. Besides, a critical approach reveal further required factors and risks to investigate. The ultimate goal is to understand how the smart city landscape is shaped by citizen-based strategies, open data, empowerment and responsibility. Accordingly, the paper closes with theoretical, practical and metaphor-based recommendations to support the business and political decision making, and also, the emerging scholarly trends in the context of upcoming technological-structural changes.

Transportation plays an important role in urban development. Population growth and environmental burden have turned the efforts of cities globally towards smarter and greener mobility. Cooperative and Connected Automated Mobility (CCAM) serves as a concept with the power and potential to help achieve these goals building upon technological fields like Internet of Things, computer vision and distributed computing. However, its implementation is hindered by various challenges covering technical parameters such as performance and reliability in tandem with other issues, such as safety, accountability and trust. To overcome these issues, new distributed and decentralized approaches like blockchain and smart contracts are needed. This paper aims at identifying a comprehensive inventory of CCAM challenges and use it as a framework to describe methodologies using blockchain and smart contracts to address them. It provides a comparative analysis of the findings to draw useful conclusions and discuss future directions in CCAM and relevant blockchain applications. The paper contributes to intelligent transportation systems’ research by offering an integrated view of the difficulties in substantiating CCAM and providing insights on the most prominent blockchain and smart contract technologies that tackle them.

In this paper, we present a novel approach for text independent phone-to-audio alignment based on phoneme recognition, representation learning and knowledge transfer. Our method leverages a self-supervised model (wav2vec2) fine-tuned for phoneme recognition using a Connectionist Temporal Classification (CTC) loss, a dimension reduction model and a frame-level phoneme classifier trained thanks to forced-alignment labels (using Montreal Forced Aligner) to produce multi-lingual phonetic representations, thus requiring minimal additional training. We evaluate our model using synthetic native data from the TIMIT dataset and the SCRIBE dataset for American and British English, respectively. Our proposed model outperforms the state-of-the-art (charsiu) in statistical metrics and has applications in language learning and speech processing systems. We leave experiments on other languages for future work but the design of the system makes it easily adaptable to other languages.

In this work, an innovative numerical approach for polylinear approximation (polylinearization) of non-self-intersecting compact sensor characteristics (transfer functions) specified either pointwise or analytically is introduced. The goal is to optimally partition the sensor characteristic, i.e. to select the vertices of the approximating polyline (approximant) along with their positions on, the sensor characteristics so that the distance (i.e. the separation) between the approximant and the characteristic is rendered below a certain problem-specific tolerance. To achieve this goal, two alternative non-linear optimization problems are solved, whose essential difference is in the adopted quantitative measure of the separation between the transfer function and the approximant. In the first problem, which relates to absolutely integrable sensor characteristics (their energy is not necessarily finite, but they can be represented in terms of convergent Fourier series), the polylinearization is constructed by numerical minimization of the L^1--metric (a distance-based separation measure), concerning the number of polyline vertices and their locations. In the second problem which covers the quadratically integrable sensor characteristics (whose energy is finite, but they do not necessarily admit a representation in terms of convergent Fourier series), the polylinearization is constructed by minimizing numerically the L^2-metric (area-, or energy-based separation measure) for the same set of optimization variables –the locations, and the number of polyline vertices.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

Industry 4.0 (I4.0) epitomizes the nexus of technological evolution and manufacturing process enhancements, underpinned by four critical pillars: Cyber-Physical Systems (CPS), Digital Twins (DT), the Industrial Internet of Things (IIoT), and Cloud Computing (CC). Through the lens of the German Reference Architectural Model Industrie (RAMI) 4.0, these components are integral to fostering Smart Manufacturing (SM) practices. In conjunction, the Asset Administration Shell (AAS) facilitates seamless inter-company communication and enables adaptability to fluctuating market demands. This paper delves into the structural intricacies of AAS and SM within the RAMI 4.0 framework, unveiling three distinct implementation strategies. Furthermore, it meticulously scrutinizes challenges that hinder the full realization of I4.0 potential, such as interoperability, security concerns, and standardized communication protocols. By examining these models and identifying current barriers, the study illuminates pathways for future research, particularly in enhancing the integration of AAS and SM systems, ensuring robust security measures, and advocating for the development of universal standards. This exploration aims to contribute to the ongoing discourse on I4.0, proposing avenues for advancing manufacturing technologies and operational frameworks in alignment with the principles of RAMI 4.0.

Smart City has emerged as the mainstream paradigm for urban governance innovation, sustainable development, and strategy upgrades, which is drawing attention from scholars worldwide. However, current frameworks for Smart City assessment remain incomplete and simplistic. In is paper, 30 national or provincial capitals in China were selected and we designed a tri-dimensional SPI model—Social, Physical, and Information Space—for smart city spatial development assessment. Utilizing methods such as entropy weighting, coupled coordination degree models, and the Dagum Gini coefficient, this study assesses the spatial development and coupled coordination of 30 cities from 2011 to 2019. Finally, by means of BP neural networks, the study examines the contribution of each indicator to the spatial coupled coordination. The results indicated that with a narrowing disparity in development speeds among different regions, the spatial coupled coordination development level of smart capitals in China has steadily increased, presenting a pattern of staggered distribution. Moreover, the IS subsystem plays the most significant role in coupled coordination. The significance of this research lies in its tri-dimensional spatial perspective of the spatial development and coupled coordination differences of the Smart City, providing evidence-based support for the regional layout and optimization in China.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

This paper investigates the periodic and quasi-periodic orbits in the symmetric collinear four-body problem through a variational approach. In Section 3, we analyze the conditions under which homographic solutions minimize the action functional. We demonstrate that these solutions for four equal masses arranged in a linear configuration are indeed the minimizers of the action functional and compute the minimum value of the action functional for these solutions. Additionally, we employ numerical experiments using Poincaré sections to explore the existence and stability of periodic and quasi-periodic solutions within this dynamical system. Our results provide a deeper understanding of the variational principles in celestial mechanics and reveal complex dynamical behaviors that are crucial for further studies in multi-body problems. The findings have significant implications for theoretical research and practical applications in astrodynamics and space mission planning.

As one of the most critical parameters to evaluate the quality and performance of mobile phones, real-time temperature monitoring of the mobile phone integrated chips is vitally important in the electronics industry. Although several different strategies for chip surface temperature measurement have been proposed in recent years, distributed temperature monitoring with the high spatial resolution is still a hot issue to be solved urgently. In this work, a fluorescent film material with photothermal properties containing thermosensitive upconversion nanoparticles (UCNPs) and polydimethylsiloxane (PDMS) is fabricated for chip surface temperature monitor-ing. The presented fluorescent films have thicknesses ranging from 23 to 90 μm and are both flexible and elastic. Using the fluorescence intensity ratio (FIR) technique, the temperature sens-ing properties of these fluorescent films are investigated. The maximum sensitivity of the fluo-rescent film was measured to be 1.43% K-1 at 299 K. By testing the temperature at different posi-tions of the optical film, a distributed temperature monitoring with a high spatial resolution down to 10 μm on the chip surface is successfully achieved. It is worth mentioning that the film maintains stable performance even under pull stretch up to 100%. The correctness of the method is verified by taking infrared images of the chip surface with an infrared camera. These results demonstrate that the as-prepared optical film is a promising anti-deformation material for high spatial resolution temperature monitoring on-chip surfaces.

At present, indoor localization is one of the core technologies of location-based services (LBS), and there exist numerous scenario-oriented application solutions. Visual features, as the main semantic information to help people understand the environment and thus occupy the dominant part, many techniques about indoor scene recognition are widely adopted. However, the engineering application problem of cell phone indoor scene recognition and localization has not been well solved due to insufficient semantic constraint information of building map and the immaturity of building map location anchors (MLA) matching positioning technology. To address the above problems, this paper proposes a cell phone indoor scene recognition and localization method with building map semantic constraints. Firstly, we build a library of geocoded entities for building map location anchors (MLA), which can provide users with "immersive" real-world building maps on the one hand and semantic anchor point constraints for cell phone positioning on the other. Secondly, using the improved YOLOv5s deep learning model carried on the mobile terminal, we recognize the universal map location anchors (MLA) elements in building scenes by cell phone camera video in real-time. Lastly, the spatial location of the scene elements obtained from the cell phone video recognition is matched with the building MLA to achieve real-time positioning and navigation. The experimental results show that the model recognition accuracy of this method is above 97.2%, and the maximum localization error is within the range of 0.775 m, and minimized to 0.5 m after applying the BIMPN road network walking node constraint, which can effectively achieve high positioning accuracy in the building scenes with rich MLA element information. In addition, the building map location anchors (MLA) has universal characteristics, and the positioning algorithm based on scene element recognition is compatible with the extension of indoor map data types, so this method has good prospects for engineering applications.

Vein blood sampling is one of the methods of mass blood sampling, and is an act of drawing blood from a vein for blood type discrimination, confirmation of various physiological indicators, disease diagnosis, and the like, and is the most commonly used blood sampling method. An important point in vein blood sampling is to search for the exact location of the vein and insert the blood sampling. This is influenced by the patient's obesity, skin and blood vessel conditions, and the experience of the clinical technologist, nurse, and resident who performs the blood sampling. It is required to perform blood sampling technique practice. However, due to many limitations of the practice room or laboratory, there is a problem of using only a limited environment and model for clinical practice. As a result, many medical educational institutions have situations in which only fragmentary clinical practices are performed, and it is difficult to per-form a large number of blood sampling skills practices, so they do not provide enough experience to understand the actual skill field. In this paper, we propose a method for developing a virtual reality-based vein blood sampling simulator to practice a large number of blood sampling techniques without restrictions. The proposed vein blood sampling simulator can operate a 3D model related to vein blood sampling using HMD Controller and Haptic in a virtual space for vein blood sampling practice by wearing an HMD (Head mounted display), and can perform vein blood sampling practice through interaction with the patient 3D model. there is. In addition, the effectiveness of the simulator developed for dental students was verified, and as a result of the verification, the potential of the proposed vein blood sampling simulator was confirmed.

Poplar and willow species in the Salicaceae are dioecious, yet have been shown to use different sex determination systems located on different chromosomes. Willows in the section Vetrix are interesting for comparative studies of sex determination systems, yet genomic resources for these species are still quite limited. Only a few annotated reference genome assemblies are available, despite many species in use in breeding programs. Here we present de novo assemblies and annotations of 11 shrub willow genomes from six species. Copy number variation of candidate sex determination genes within each genome was characterized and revealed remarkable differences in putative master regulator gene duplication and deletion. We also analyzed copy number and expression of candidate genes involved in floral secondary metabolism, and identified substantial variation across genotypes, which can be used for parental selection in breeding programs. Lastly, we report on a genotype that produces only female descendants and identified gene presence/absence variation in the mitochondrial genome that may be responsible for this unusual inheritance.

The increase in population and the challenges caused by it are always among the concerns of decision-makers and policymakers in large countries. One of the most serious concerns is in the field of energy consumption. Optimizing energy use is one of the most effective ways to manage limited resources and energy. Energy consumption in residential houses constitutes a significant percentage of the total energy consumption worldwide; therefore, current research focusing on mathematical models aims to provide a predictive multi-objective linear mathematical model for residential house consumption. For this purpose, the consumption of water, electricity, and gas for 80 residential houses, including 10 household appliances and equipment on a weekly basis, has been considered. The results showed that the mixed-integer multi-objective predictor model is able to optimize household consumption plans compared to the actual state of household energy consumption. Since the goals of household satisfaction and energy consumption costs in the model conflict with each other, the influence coefficient was calculated to demonstrate the simultaneous achievement of these goals. The optimal value achievable with the default model for the model's purposes is 69%.

The objective of this study was to carry out the extraction and characterization of chitin and chitosan from the exoskeletons of the Farfantepenaeus californiensis species of shrimp, as well as its application in the formulation of polymeric films plasticized with glycerol used in the process of food packaging. The characterization of the extracted polymer was made by Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), and physicochemical analysis of chitin and chitosan, resulting in a theoretical performance of 29.33% and 16.46%, respectively. In terms of quality, it was determined that the extracted chitosan had a molecular weight of 1.10 x105 g/mol and a deacetylation degree of 80.23%, which classifies it as a low-molecular weight chitosan, suitable for food packaging. It was shown that the extracted chitosan is fit for the production of the films by using the casting method, presenting a tension resistance of 1 MPa. The Antibacterial analysis was carried out using Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), bacterial models commonly found in food. The results showed an effective inhibition capability of the polymeric materials. Overall, the results for both chitosan and the films indicate a high potential for application in the food packaging sector.

As digital technology has become an integral part of urban’s daily operations; the urban landscape is constantly evolving with the needs of its society. This new reality allowed Municipalities to exert a higher influence in the national and local economy. Through deliberate planning and executing initiatives, they can ignite the local financial ecosystem to growth. In line with this, the paper aims to understand the possibilities available to the Greek Municipalities to exploit the smart city benefits to foster economic development. It is essential to understand the role of different factors including the strategy during the planning and implementing phases of initiatives concerning economy and innovation in a smart city. To achieve this, a tailor-made questionnaire and advanced statistical techniques are applied. The main findings highlight the importance to plan initiatives aligned with the needs of the municipality and the business environment. The existence of a smart city strategy has a catalytic effect on the final impact of the implemented initiatives on the urban environment. A systematic analysis of the smart cities’ dynamics and the new state of the urban environment can help the local actors focus on the value creation and public service provision, fostering innovation and profitability.

The teaching and learning environment have changed significantly over the last decade with the integration of an increasing amount of information and communication technologies, especially in distance education due to global pandemics, total lockdowns, isolation, and quarantine periods. The number of numerous virtual and non-virtual tools involved in educational processes is growing day by day. In terms of technological innovations used in learning environments, many researchers and educators are trying their best to bring more creative ideas into the technology- based learning environments. Although higher educational institutions have greatly benefited from the growing number of hardware and software resources in the educational process, they have also faced some setbacks that have harmed the learning processes. These technologies have in turn complicated some of the processes in the learning atmosphere. Therefore, we take Spanish teaching course as an example to present the challenging smarter teaching and learning systems that higher educational institutions face today.

It is well established that the interacting effects of temperature and precipitation will alter agroecological systems on a global scale. These shifts will influence the fitness of specialty crops, specifically strawberries (Fragaria x ananassa), an important crop in the Northeastern United States. In this study, four precipitation scenarios were developed that are representative of current and probable-future growing season precipitation patterns. Using a precipitation simulator, we tested these scenarios on potted day neutral strawberries. This study generated four primary results: (1) though treatments received different amounts of precipitation, little difference was observed in soil volumetric water content or temperature. However, treatments designed to simulate future conditions were more likely those designed to simulate current conditions to have higher nitrate-in-leachate (N-leachate) concentrations; (2) neither total precipitation nor seasonable distribution were associated with foliar or root disease pressure; (3) while there was a slightly higher chance that photosynthetic potential and capacity would be higher in drier conditions, little difference was observed in the effects on chlorophyll concentration, and no water stress was detected in any treatment; and (4) leaf biomass was likely more affected by total rather than seasonal distribution of precipitation, but interaction between changing rainfall distribution and seasonal totals is likely to be an important driver of root biomass development in the future.

This article provides a detailed analysis of non-invasive techniques for prediction and diagnosis of faults in internal combustion engines, focusing on the application of the Proknow-C and Methodi Ordinatio systematic review methods. Initially, the relevance of these techniques in promoting energy sustainability and mitigating greenhouse gas emissions is discussed, aligning with the Sustainable Development Goals (SDGs) of Agenda 2030 and the Paris Agreement. The systematic review conducted in the subsequent sections offers a comprehensive mapping of the state-of-the-art, highlighting the effectiveness of combining these methods in categorizing and systematizing relevant scientific literature. The results reveal significant advancements in the use of artificial intelligence (AI) and digital signal processors (DSP) to enhance fault diagnosis, as well as underscore the crucial role of non-invasive techniques in minimizing interference in monitored systems. Finally, concluding remarks point towards future research directions, emphasizing the need to develop digital twins for internal combustion engines and identify gaps for further improvements in fault diagnosis and prediction techniques.

The rapid increase in the number of mobile phone base stations (MPBS) has raised global concerns about the potential adverse health effects of exposure to radiofrequency electromagnetic fields (RF-EMF). The application of machine learning techniques can enable healthcare professionals and policymakers to proactively address concerns surrounding RF-EMF exposure near MPBS. In this study, we investigated the potential of machine learning models to predict health symptoms associated with RF-EMF exposure in individuals residing near MPBS.We utilized support vector machine (SVM) and random forest (RF) algorithms, incorporating 11 predictors related to participants' living conditions. A total of 699 adults participated in the study, and model performance was assessed using sensitivity, specificity, accuracy, and the area under the receiver operating characteristic curve (AUC). The SVM-based model demonstrated strong performance, achieving accuracies of 85.3%, 82%, 84%, 82.4%, and 65.1% for headache, sleep disturbance, dizziness, vertigo, and fatigue, respectively. The corresponding AUC values were 0.99, 0.98, 0.920, 0.89, and 0.81. Compared to the RF model and a previously developed model, the SVM-based model exhibited higher sensitivity, particularly for fatigue, with sensitivities of 70.0%, 83.4%, 85.3%, 73.0%, and 69.0% for these five health symptoms. Particularly for predicting fatigue, sensitivity and AUC were significantly improved (70% vs 8% and 11.1% for SVM, MLPNN, and RF, respectively, and 0.81 vs 0.62 and 0.64, for SVM, MLPNN, and RF, respectively). These findings suggest that machine learning methods, specifically SVM, hold promise in effectively managing health symptoms in individuals residing near or planning to settle in the vicinity of MPBS.

Can the smart city provide a new perspective for public and academic libraries? How does the smart city impact the libraries as cultural and scientific assets? And how can libraries contribute to the development of the smart city? An overview of recent library models, like the learning center or the green library, reveals affinities with the concept of the smart city, especially regarding the central role of information and the integration of technology, people and institution. From this observation, the paper develops the outline of a new concept of the smart library which can be described on four dimensions, i.e. smart services, smart people, smart place and smart governance. However, the smart library concept does not constitute a unique model or project but a process, a way how to get things done, less linear, less structured, more creative and innovative. Also, smartness may not be a solution for all library problems.

The influence of technology corporations on the development of smart cities can generate corporate-centric models of governance. Thus, it is relevant to examine which governance models help to promote sustainability. Based on a rapid review on the governance of smart cities, this paper aims to evaluate the merits and drawbacks of various governance models adopted by diverse smart city initiatives. It contends that top-down models often prioritize corporate-centric governance structures, potentially neglecting sustainability concerns. Nonetheless, our findings indicate that top-down approaches can mitigate corporate-centric tendencies by integrating citizen participation into their visions and strategies. Hybrid models offer the advantage of governmental leadership but may lean towards a triple-helix model, with limited citizen involvement. Conversely, bottom-up models represent quadruple-helix collaborations with active citizen engagement.

Grid modernization has been ushered in by rising electricity consumption, deteriorating infrastructure, and increasing reliability concerns for electric utilities. New advances, collectively referred to as the smart grid, include modern electronics, technology, telecommunications, and computing capabilities. Smart grid telecommunication frameworks provide two-way communication to support grid operations. Software-defined networking (SDN) has been proposed as a method of monitoring and controlling telecommunication networks, enabling increased smart grid visibility, control, and security. However, being connected to telecommunications infrastructure means that smart grid networks are exposed to cyber-attacks. Attackers may use unauthorized access to intercept messages, inject false data into system measurements, flood communication channels with false data packets, or target centralized controllers to cripple network control. Defense and security techniques against these threats are constantly evolving, necessitating an up-to-date, comprehensive study analyzing cyber attacks and defense methods for smart grid networks. Previous smart grid security surveys do not contain recent techniques and to our knowledge most, if not all, address only one type of attack type and/or one type of defense. This survey considers the latest security techniques, simultaneous multi-pronged cyber attacks and defensutilityes to meet the challenges of the next-generation SDN smart grid research with the goal of identifying future research needs, describing the open security challenges, and exposing both emerging threats and their potential impact on SD-SG deployment.

Artificial Intelligence (AI) and Deep Reinforcement Learning (DRL) have revolutionised e-learning by creating personalised, adaptive, and secure environments. However, challenges such as privacy, bias, and data limitations persist. E-FedCloud aims to address these issues by providing more agile, personalised, and secure e-learning experiences. This study introduces E-FedCloud, an AI-assisted adaptive e-learning system that automates personalised recommendations and tracking, thereby enhancing student performance. It employs federated learning-based authentication to ensure secure and private access for both course instructors and students. Intelligent Software Agents (ISAs) evaluate weekly student engagement using the Shannon Entropy method, classifying students into either engaged or not-engaged clusters. E-FedCloud utilises weekly engagement status, demographic information, and an innovative DRL-based early warning system, specifically ID2QN, to predict the performance of not-engaged students. Based on these predictions, the system categorises students into three groups: risk of dropping out, risk of scoring lower in the final exam, and risk of failing the end exam. It employs a multi-disciplinary ontology graph and an attention-based capsule network for automated, personalised recommendations. The system also integrates performance tracking to enhance student engagement. Data is securely stored on a blockchain using the LWEA encryption method.

Objects recognition is a necessary task in smart city environments. This recognition can be used in processes such as the reconstruction of the environment map or the intelligent navigation of vehicles. This paper proposes an architecture that integrates heterogeneous distributed information to recognize objects in intelligent environments. The architecture is based on the IoT / Industry 4.0 model to interconnect the devices, called Smart Resources. Smart Resources can process local sensor data and send information to other devices. These other devices can be located in the same operating range, the Edge, in the same intranet, the Fog, or on the Internet, the Cloud. Smart Resources must have an intelligent layer in order to be able to process the information. A system with two Smart Resources equipped with different image sensors has been implemented to validate the architecture. Experiments show that the integration of information increases the certainty in the recognition of objects between 2\% and 4\%. Consequently, in the field of intelligent environments, it seems appropriate to provide the devices with intelligence, but also capabilities to collaborate closely with other devices.

Wireless Sensor Networks (WSNs) are gaining traction in the realm of network communication, renowned for their adaptability, configuration, and flexibility. The forthcoming network traffic within WSNs can be forecasted through temporal sequence models. In this correspondence, We present a method (TSENet) that can accurately predict the traffic in the cellular network. TSENet is composed of transformers and self-attention network. We have designed a temporal transformer module specifically for extracting temporal features. This module accomplishes this by modeling the traffic flow within each grid of the communication network at both near-term and periodical intervals. Simultaneously, we amalgamate the spacial features of each grid with information from its correlated grids, generating spacial predictions within the spacial transformer. Furthermore, we employ self-attention aggregation to capture dependencies between external factor features and celluar data features. Empirical assessments performed on a genuine cellular traffic dataset offer compelling evidence substantiating the efficacy of TSENet.

According to ISO/TR 23383, smart textiles reversibly interact with their environment and respond or adapt to changes in the environment. The present review and bibliometric analysis was performed on 5,810 documents (1989–2022) from the Scopus database, using VOSviewer and Bibliometrix/Biblioshiny for science mapping. The results show that the field of smart textiles is highly interdisciplinary and dynamic, with an average growth rate of 22% and exponential growth in the last 10 years. Beeby, S.P., and Torah, R.N. have published the highest number of papers, while Wang, Z.L. has the highest number of citations. The leading journals are Sensors, ACS Applied Materials and Interfaces, and Textile Research Journal, while Advanced Materials has the highest number of citations. China is the country with the most publications and the most extensive cooperative relationships with other countries. Research on smart textiles is largely concerned with new materials and technologies, particularly in relation to electronic textiles. Recent research focuses on energy generation (triboelectric nanogenerators, thermoelectrics, Joule heating), conductive materials (MXenes, liquid metal, silver nanoparticles), sensors (strain sensors, self-powered sensors, gait analysis), specialty products (artificial muscles, soft robotics, EMI shielding), and advanced properties of smart textiles (self-powered, self-cleaning, washable, sustainable smart textiles).

Today, mobile phones are at the center of many consumers' lives and a part of people's lives. Although this tool was considered a luxury initially, it has gradually become a necessary tool with the reduction of the price and the increase of its functions. Consumers choose specific models of mobile phones according to their needs. Mobile phones have quality features that are expressed in the form of quality dimensions. These dimensions are mostly expressed by word of mouth (WOM). In this research, first; we collected the opinions of 350 students about 4 brands of mobile phones based on Garvin's quality of dimensions, finally; the students’ opinions about mobile phones were evaluated with integrated TOPSIS with interval-valued intuitionistic fuzzy numbers technique, and the priority of 4 phone brands was determined based on students' opinions.

Abstract：Commuting of residents in big city often brings tidal traffic pressure or congestions. Understanding the causes behind this phenomenon is of great significance for urban space optimization. Various spatial big data make possible the fine description of urban residents travel behaviors, and bring new approaches to related studies. The present study focuses on two aspects: one is to obtain relatively accurate features of commuting behaviors by using mobile phone data, and the other is to simulate commuting behaviors of residents through the agent-based model and inducing backward the causes of congestion. Taking the Baishazhou area of Wuhan, a local area of a mega city in China, as a case study, travel behaviors of commuters are simulated: the spatial context of the model is set up using the existing urban road network and by dividing the area into travel units; then using the mobile phone call detail records (CDR) of a month, statistics of residents' travel during the four time slots in working day mornings are acquired and then used to generated the OD matrix of travels at different time slots; and then the data are imported into the model for simulation. By the preset rules of congestion, the agent-based model can effectively simulate the traffic conditions of each traffic intersection, and can also induce backward the causes of traffic congestion using the simulation results and the OD matrix. Finally, the model is used for the evaluation of road network optimization, which shows evident effects of the optimizing measures adopted in relieving congestion, and thus also proves the value of this method in urban studies.

While the mobile phone is the world’s most popular media device, it is actually not one single medium, but is effectively used as a different medium by different user groups. The article characterizes polymodal differences in mobile apps usage among different user groups, including gender, education, occupation, screen size, and price. We monitored the complete app usage of 10,725 smartphone users for one month each (56 million sessions, recording almost 1 million hours). Our key contribution consists in developing and analyzing a theoretical framework to classify the over 16,000 apps used into five categories. Exploring nine research questions we provide a broad characterization by asking who, with which characteristics, uses which kinds of apps in what extensity and intensity? For example, it is not the young and high occupational grades that use the mobile phone as a human-to-machine computer (including gaming and artificial intelligence tools). Large screen size is related to extensive long sessions, while a small screen size is related to intensive frequent usage. The results go beyond providing ample empirical evidence for the inherently polymodal nature of the mobile phone, but also proposes a framework on how to possibility deal with it analytically.

Software-Defined Networking (SDN) has revolutionized network management by providing unprecedented flexibility, control, and efficiency. However, its centralized architecture introduces critical security vulnerabilities. This paper presents an innovative approach to securing SDN environments using IOTA 2.0 smart contracts. The proposed system leverages the IOTA Tangle, a directed acyclic graph (DAG) structure, to enhance scalability and efficiency while eliminating transaction fees and reducing energy consumption. We introduce three smart contracts—Authority, Access Control, and DoS Detector—to ensure secure network operations, prevent unauthorized access, and mitigate denial-of-service attacks. Through comprehensive simulations using Mininet and the ShimmerEVM IOTA Test Network, we demonstrate the efficacy of our approach in enhancing SDN security. Our findings highlight the potential of IOTA 2.0 smart contracts to provide a robust, decentralized solution for securing SDN environments, paving the way for further integration of blockchain technologies in network management.

Cities are undergoing huge shifts in technology and operations in recent days, and `data science' is driving the change in the current age of the Fourth Industrial Revolution (Industry 4.0 or 4IR). Extracting insights or actionable knowledge from city data and building a corresponding data-driven model is the key to making a city system automated and intelligent. Data science is typically the study and analysis of actual happenings with historical data using a variety of scientific methodology, machine learning techniques, processes, and systems. In this paper, we concentrate on and explore ``Smart City Data Science", where city data collected from various sources like sensors and Internet-connected devices, is being mined for insights and hidden correlations to enhance decision-making processes and deliver better and more intelligent services to citizens. To achieve this goal, various machine learning analytical modeling can be employed to provide deeper knowledge about city data, which makes the computing process more actionable and intelligent in various real-world services of today's cities. Finally, we identify and highlight ten open research issues for future development and research in the context of data-driven smart cities. Overall, we aim to provide an insight into smart city data science conceptualization on a broad scale, which can be used as a reference guide for the researchers, professionals, as well as policy-makers of a country, particularly, from the technological point of view.

This article provides a comprehensive review of the intersection of 5G technology and Beyond, and Smart Grids, focusing on the potential of Vehicle-to-Fog as an industrial alternative for addressing energy efficiency challenges in data processing. This study aims to investigate relevant articles and patents to understand the collaborative potential between 5G and Smart Grids. It explores how to establish new regulatory standards within the architectural framework of 5G to facilitate decentralized data processing and remodel energy consumption patterns. The hypothesis suggests that decentralized 5G architecture and Smart Grids can be most effectively applied through vehicular fogging powered by solar energy. A combined quantitative and qualitative methodology guides the exploration of articles and patents. The study concludes by advocating for new standards that embrace decentralized 5G data processing, emphasizing the potential of Vehicle-to-Fog and the future deployment of 6G technology in Smart Grids. These advancements can significantly enhance energy efficiency in the context of 5G and pave the way for future innovations.

Over the recent decades people’s (rural and urban) communities are facing numerous social and economic changes and challenges. Some of those challenges have been increasingly addressed through the lenses of technological developments and digitalization. In this paper we have made a review of already existing practices while focusing on the existing implementations of the smart village concept and the importance of digital transformation for rural areas. We give special attention to EU policies which we are using as an already existing framework for understanding our own forthcoming examples. We have shown the parallels between the findings and insights from different regions and made an evaluation of presented practices. Our main argument stems from our own previous experiences and experiences of other research approaches, and is grounded on the argument that rural areas are not uniform, and that smart rural development has to be applied in combination with place-based approach. We present the cases of Slovenian pilot practices and support our argument by proposing the FabVillage concept.

The complexity and interconnection of smart cities provide huge political, technical, and socioeconomic challenges for the designers, integrators, and organisations who are responsible for the administration of these new entities. A growing number of studies are concentrating their attention on the safety, privacy, and potential dangers that exist within smart cities. These studies are drawing attention to the dangers that are associated with information security as well as the challenges that smart city infrastructure faces in the management and processing of personal data. This state of the art review of the literature analyses a number of issues pertaining to smart homes, offers a helpful synthesis of the important information found in the primary research, and creates a model for the interaction between smart cities. An overview of smart home research incorporating machine learning, including everything from definition to current research state. The state of art begins with a smart home definition, followed by descriptions of smart home elements, typical research projects, smart home network research status, smart home appliances, and difficulties. The term "smart home" refers to a subcategory of "everyday computing" that includes "smart technology" in order to improve a person's level of convenience, health, safety, and security while also reducing their When controlled by artificial intelligence, the applications for the smart home provide users with context-aware settings, services, and remote control, which significantly increases the level of user satisfaction.

Background: HIV poses a threat to global health. With effective treatment options available, education and testing strategies are essential in preventing transmission. Text messaging is an effective tool for health promotion and can be used to target higher risk populations. This study reports on the design, delivery and testing of a mobile text messaging SMS intervention for HIV prevention and awareness, aimed at adults in the construction industry and delivered during the COVID-19 pandemic. Method: Participants were recruited at Test@Work workplace health promotion events (21 sites, n=464 employees), including health checks with HIV testing. Message development was based on a participatory design and included a focus group (n=9) and message fidelity testing (n=291) with assessment of intervention uptake, reach, acceptability, and engagement. Barriers to HIV testing were identified and mapped to the COM-B behavioural model. 23 one-way push SMS messages (19 included short web links) were generated and fidelity tested, then sent via automated SMS to two employee cohorts over a 10-week period during the COVID-19 pandemic. Engagement metrics measured were; opt-outs, SMS delivered/read, number of clicks per web link, and four two-way pull messages exploring repeat HIV testing, learning new information, perceived usefulness and behaviour change. Results: 291 people participated (68.3% of eligible attendees). A total of 7,726 messages were sent between March and June 2020, with 91.6% successfully delivered (100% read). 12.4% of participants opted out over 10 weeks. Of delivered messages, links were clicked an average of 14.4%, max 24.1% for HIV related links. The number of clicks on web links declined over time (r= -6.24, p=0.01). Response rate for two-way pull messages was 13.7% of participants. Since the workplace HIV test offer at recruitment, 21.6% reported having taken a further HIV test. Qualitative replies indicated behavioural influence of messaging on exercise, lifestyle behaviours and intention to HIV test. Conclusion: SMS messaging for HIV prevention and awareness is acceptable to adults in the construction industry, has high uptake, low attrition and good engagement with message content, when delivered during a global pandemic. Data collection methods may need refinement for audience and effect of COVID-19 on results is yet to be understood.

No doubt pollution is a global problem which must be holistically tackled. In doing this, adequate knowledge of the sources of pollution is important, therefore the aim of this paper is to review source apportionment with reference to top-down and bottom-up methods. In this paper, dispersion modeling, emissions inventory, and sampling methods were discussed. Also, analytical methods involved in top-down source apportionment were mentioned. The two techniques are needed to evaluate pollutants and their sources. Based on these two approaches, pollution control strategy would be developed and decisions can be made in deciding the right approach to solve or reduce the pollution problems.

: Medical gloves, along with masks and gowns, serve as the initial line of defense against poten-tially infectious microorganisms and hazardous substances in the health sector. During the COVID-19 pandemic, medical gloves played a significant role, as they were widely utilized by society in daily activities as a preventive measure. These products demonstrated their value as important personal protection equipment (PPE) and reaffirmed their relevance as infec-tion-prevention tools. This review describes the evolution of medical gloves since the discovery of vulcanization by Charles Goodyear in 1839, which fostered the development of this industry. Regarding the current market, a comparison of the main properties, benefits, and drawbacks of the most widespread types of sanitary gloves is presented. The most usual gloves are produced from natural rubber (NR), polyisoprene (IR), acrylonitrile butadiene rubber (NBR), polychloroprene (CR), polyethylene (PE), and poly(vinyl chloride) (PVC). Furthermore, the environmental impacts of the conventional natural rubber gloves manufacturing process and mitigation strate-gies, such as bioremediation and rubber recycling, are addressed. In order to create new smart medical gloves with improved properties, several biopolymers (e.g. poly(vinyl alcohol) and starch) and additives such as biodegradable fillers (e.g., cellulose and chitin), reinforcing fillers (e.g. silica and cellulose nanocrystals), and antimicrobial agents (e.g., biguanides and quaternary ammonium salts) have been evaluated. This paper covers these smart materials and describes different innovative prototypes of gloves and coatings designed with them.

Placing the needle inside the epidural space for locoregional anesthesia is a challenging procedure, which even today is left to the expertise of the operator. Recently, we have demonstrated that the use of optically sensorized needles significantly improve the effectiveness of such procedure. Here we propose an optimized configuration, where the optical fiber strain sensor is directly integrated inside the epidural catheter. The new design allows to solve the biocompatibility issues and increases the versatility of the former configuration. Through an in vivo study carried out on a porcine model we confirm the reliability of our approach, which also opens the way to catheter monitoring during its insertion inside biological spaces.

Universities, like cities, have embraced novel technologies and data-based solutions to improve their campuses with ‘smart’ becoming a welcomed concept. Campuses in many ways are small-scale cities. They increasingly seek to address similar challenges and to deliver improved experiences to their users. How can data be used in making this vision a reality? What can we learn from smart campuses that can be scale up to smart cities? A short research study was conducted over a three-month period at a public university in the United Kingdom employing stakeholder interviews and user surveys, aiming at gaining insight into these questions. Based on the study, the authors suggest that making data publicly available could bring many benefits to different groups of stakeholders and campus users. These benefits come with risks and challenges such as data privacy and protection and infrastructure hurdles. However, if these challenges can be overcome, open data could contribute significantly to improving campuses and user experiences, and potentially set an example for smart cities.

Although the majority of mobile phone (MP) users do not attribute adverse effects on health or well-being to MP-emitted radiofrequency (RF) electromagnetic fields (EMFs), the exponential increase in the number of RF devices necessitates continuing research aimed at the objective investigation of such concerns. In this work, we investigate the effects of acute exposure from Long Term Evolution (LTE) MP EMFs on thermal pain threshold in healthy young adults. We use a protocol that was validated in a previous study in a capsaicin-induced hyperalgesia model, and was also successfully used to show that exposure from an RF source mimicking a Universal Mobile Telecommunications System (UMTS) MP led to mildly stronger desensitization to repeated noxious thermal stimulation relative to the sham condition. Using the same experimental design, we did not find any effects of LTE exposure on thermal pain threshold. The present results are in accordance with previous evidence suggesting that effects are likely to be placebo/nocebo effects and are unrelated to the brief acute LTE EMF exposure itself. The fact that this is dissimilar to our previous results on UMTS exposure implies that RF modulations might differentially affect pain perception, and points to the necessity of further research in the topic.

Smart grids represent the evolution of traditional electrical grids through the integration of digital and communication technologies. These grids are capable of monitoring and managing the distribution of electricity efficiently and resiliently. Artificial Intelligence (AI) plays a crucial role in this context, offering advanced solutions for optimization, forecasting, and energy management. This paper explores the main AI technologies applied to smart grids, highlighting their advantages, challenges, and impacts on energy efficiency and sustainability. The methodology employed includes a comprehensive literature review, analysis of current AI applications in smart grids, and examination of case studies to illustrate the practical implementation and benefits of AI technologies in this field.

The rapid integration of Information and Communication Technology (ICT) is transforming the traditional electrical grid into a {\em Smart Grid}. Smart grids enable two-way communication and improved monitoring and control between utilities and customers. However, due to its heterogeneous nature, public exposure, and weak security at low-powered devices, the Smart Grid has vulnerabilities to various malicious threats, adversaries, and cyber attacks, which may affect cost and service availability. Additionally, when the systems' confidentiality, integrity, or availability are compromised, the resulting fallout can threaten national security and have cascading effects on human lives. Given the extreme consequences of an attack, smart-grid technology must be thoroughly tested for correct operation and security {\em before} it is deployed. As a result, vulnerability testing of smart grids, not only for correctness but for security purposes, has been the subject of numerous studies by academics, government agencies, and private companies. This paper reviews the vulnerabilities associated with the smart grid and spotlights simulation as the vulnerability testing methodology conducted in recent pertinent research works. It also presents various security aspects of the smart grid, including grid applications, system and network infrastructure and components, cyber threats and attacks, simulation, and different mitigation techniques. Finally, we analyze the gaps in the current research works, focusing on simulation. We briefly present a real-time simulation testbed that mimics customer behaviour and integrates hardware in the loop to apply attack methods, analyze vulnerabilities and risk mitigation associated with the smart grid system, and propose future work to improve the current framework.

Urban planning is recognized as an interaction between the state and society, which aims to articulate public policies in the territory, facilitating their administration in favor of greater development and well-being of society. However, this interaction becomes complex because consumption demands increase, and the needs of the community exceed the capacity of the urban ecosystem to supply them, hindering its sustainable functionality. With this panorama, it becomes relevant to study urban planning from a sustainable environmental planning perspective, based on four topics: urban planning, sustainability, resilience and smart cities. The methodology used is based on a bibliometric study through a PRISMA adjustment to 87 articles, supported by VOSviewer® to construct and visualize the co-occurrence networks of important terms extracted from a body of scientific literature. The main result is to consider cities with a complex systems approach that works like a gear, that is, there is a connective element between inter- and intra-urban processes. This relationship is the key factor that allows understanding their synchronization, stating that the deepening of each of these topics is crucial to the ideal of a territorial administration through time scales, by means of adaptive cycles, allowing to provide new tools to concepts such as carrying capacity and the measurement of the environmental footprint.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

During the last decade, smart materials have increasingly impacted on several niches, among which that of one-off/limited edition experimental fashion. Thanks to their performativity, due to the implementation of Smart Materials Systems, they have reached indeed catwalks as well as museums and galleries. As boundaries between what-is-art and what traditionally was not supposed to be art are now turning into osmotic membranes, zooming on how smart materials are highly contributing to outline the new creative landscape can provide with interesting and compelling issues. Introducing three different areas of experimental fashion, named Multi-sensory dresses, Empathic dresses, and Bio-smart dresses and accessories, respectively covering the world of in-Lab experiments and design collaborations in relation to the application of advanced smart materials systems, the article discuss some of the implications in term of Design Thinking and Design Aesthetics.

With the rise of serious problems of urbanization and climate change, the call for intelligent and sustainable urban development is increasing nowadays. Therefore, smart cities have become a hot topic in academia, industry, and politics, resulting in the emergency of numerous smart city programs and projects. This study selected 26 evaluation frameworks proposed in recent years or large-scale research projects that have lasted for many years and analyzed and compared them from the 7 aspects of generalizability, comprehensiveness, availability, flexibility, scientific, transparency, and interpretability. The result indicates that the current smart city evaluation framework still needs to be upgraded and updated. These standards can not only guide the development direction and hotspot of the future smart city evaluation model but also serve as a guide for model demanders to test results and an effective tool to verify the framework designed by themselves.

Sustainability is pivotal in the urban transformation strategy in order to reach more resource-efficient, resilient and smarter cities. The goal of being a sustainable city should drive the decisions for city interventions. Nonetheless, impacts need to be quantified, lacking of standard and/or common methodologies that could be replicable across multiple cities. There exist many initiatives aiming at defining indicators and assessment procedures, but without convergence in the definition of terms and application methodologies, making complex its real implementation. Within mySMARTLife project (GA#731297), a KPI-driven evaluation framework is defined with the aim of covering the multiple pillars of a city (i.e. energy, mobility, citizens, economy) in a holistic way. This methodology also defines the concepts and terms to guide urban planners and/or experts at time of implementing the framework in a specific city. The evaluation framework has been deployed in the three cities of Nantes, Hamburg and Helsinki and some lessons learnt have been extracted, such as the necessity of providing a definition of measurement boundary to avoid interpretations. Thanks to a co-creation strategy, the main difficulties and issues from the cities have been taken into consideration for increasing the replicability.

Information and Communication Technology (ICT) is at the heart of the Smart City approach, which constitutes the next level of cities’ and communities’ development across the globe. Thereby, ICT serves as the gluing component enabling different domains to interact with each other and facilitating the management and processing of vast amounts of data and information towards intelligently steering the cities infrastructure and processes, engaging the citizens and facilitating new services and applications on various aspects of urban life - e.g. supply chains, mobility, transportation, energy, citizens’ participation, public safety, interactions between citizens and the public administration, water management, parking and many other use cases and domains. Hence, given the fundamental role of ICT in cities in the near future, it is of paramount importance to lay the ground for a sustainable and reliable ICT infrastructure, which can enable a city/community to respond in a resilient way to upcoming challenges whilst increasing the quality of life for its citizens. This paper constitutes a continuation of a series of research documents and standardization activities, which relate to the concept of Open Urban Platforms (OUP) and the way they serve as a blueprint for each city/community towards the establishment of an ICT backbone. Thereby, the current paper emphasizes on the aspects of sustainability and resilient ICT, whilst reporting on our latest activities and related developments in the research area.

Background: Smart transport plays a crucial role in urban planning and the transition from traditional to smart cities in developing countries with sustainability requirements.Traditional cities in developing countries often suffer from traffic congestion,air pollution, and inadequate public transportation systems,which can impede economic growth and negatively impact the quality of life for residents. Smart transport solutions can address these challenges by providing more efficient, sustainable.Here is a possible business model for an ITS system in a high-potential city in Iran,Based on IoT analysis, Mashhad city in Iran selected as a high-potential city to be changed to a smart city in the transportation sector.In the localization business model,the Uber smart transportation business model as a successful world experience is considered the base model. Methods: Based on the literature review,various criteria and sub-criteria were identified and determined in designing a new localized transportation business model.A questionnaire was prepared and filled with the help of 11 experts,method IAHP technique; Results:The present study showed the possibility of monthly payments for customers,software development, and the addition of luxury cars are among the most important sub-criteria with high weights;Conclusions: Working with transport companies,schools and universities as key partners solves reaching a strong and sustainable smart transportation system.

The widespread adoption of electromobility constitutes one of the measures designed to reduce air pollution caused by traditional fossil fuels. However, several factors are currently impending this process, ranging from insufficient charging infrastructure, battery capacity, long queueing and charging time, to psychological factors. On top of range anxiety, the frustration of the EV drivers is further fueled by the lack the uncertainty of finding an available charging point on their route. To address this issue, we propose a solution that comes to bypass the limitations of the Reserve now function of the OCPP standard, enabling drivers to make charging reservations for the upcoming days, especially when planning a longer trip. We created an algorithm that generates reservation intervals based on the charging station's reservation and transaction history. Subsequently, we ran a series of test cases that yielded promising results, with no overlapping reservations.

Turmeric is highly tolerant to several climatic changes and can grow under high temperatures and moderate drought conditions. This herb is very much dependant on optimum rainfall, optimum heat with less chilling or freezing conditions. These conditions if are more than normal would tend to reduce the yields of the crops and also effect the productivity. To reduce such drastic yield losses certain conventional plant breeding methods were employed but were very less effective compared to plant biotechnology. To reduce these loses by stresses, extensive and effective molecular biology methods were employed which identifies the genes that are stress responsive along with certain methods like gene transfer, genetic engineering was also known to be effective. All these methods are quite helpful in mitigating the yield losses and promoting healthy growth in the plants. The maintenance of rhizome size, curcumin content, essential oils etc. is very much necessary for the turmeric crop because of its role, especially in the medical field. Therefore, the yield losses are reduced to a maximum extent so that development of smart turmeric is easy and crop designing is possible only with the advanced techniques involved in agriculture biotechnology.

The definition of a Smart-complex of educational discipline and its technology is given. Attention is focused on the form of the Smart-complex and constructive elements: the creative educational environment, the author's environment, the non-verbal environment, the encyclopedia, the creative / self-realization environment, the monitoring / self-evaluation environment.A feature of the Smart-complex of the academic discipline is the integration into it of the structural equalization block. Constructive alignment (alignment) is based on the design of the student's own learning participation in educational projects. Alignment refers to creating an appropriate learning environment and involves selecting the most appropriate training activities and evaluating each learning outcome. If the result of the training is to develop analytical skills, then for the assessment it is necessary to build questions and scenarios for their development.Two main components of the structural alignment are considered: 1) the first component is based on cognitive psychology and constructivist theory, recognizes the importance of linking new material with the concepts and experiences of students and extrapolation to possible future scenarios in the process of mission activity - they comprehend what they are doing during training; 2) the second component is based on the declaration by the teacher of the correspondence between the planned educational activities and the results of the training of students. This makes planning of educational activities and development of self-assessment criteria for organizing feedback. It is necessary to take into account the impact of Smart-complexes of educational disciplines on three think-tank training networks: 1) effective networks (why learn) - several ways of presenting to give students different ways of obtaining information and knowledge; 2) recognition networks (learning outcomes) - several ways of expressing them to provide them with an alternative for demonstrating what they know; 3) strategic exercises (how to learn) - several ways to increase the motivation for learning to attract their attention to both their own learning project and its technical and historical decision. Smart-complexes of educational disciplines should be: 1) scientific; 2) with user-friendly interface; 3) have a connection with LMS; 4) structured; 5) with visual material; 6) working in Off-line mode; 7) used on various devices in an educational institution, as well as at home.

In the smart city, information and communications technologies (ICTs) are proposed as solutions to urban challenges, including sustainability concerns. While sustainability commonly refers to economic and environmental dimensions, the concept also contains a social component. Our study asked how smartphone applications (apps) address social sustainability challenges in urban transport, if at all. We focused on transport disadvantages experienced due to low income, physical disability, and language barriers. A review of 60 apps showed that transport apps respond to these equity and inclusion issues in two ways: (a) by employing universal design in general-use apps; including cost-conscious features; and providing language options (b) by specifically developing smartphone apps for persons with disabilities. The article discusses the study by positioning it in the literature of smart cities as well as socially sustainable transport.

Information and communication technologies play an increasingly important role in the process of knowledge and management of places at different scales. ICTs allow a rapid diffusion of data not only through institutional channels but also through social networks where the smart community share experiences and perceptions. In this sense, ICTs become strategic tools to support the promotion of sustainable tourism development of territories, especially if the digital data are organised within a circular smart dashboard. This research focuses on the case study of the Santa Barbara Walk (SBW), an ancient mining route in the Sulcis Iglesiente region (Sardinia, Italy), where the authors have recognized a state of disorganization in slow tourism promotion activities. In fact, if the SBW represents a network - material infrastructure - which connects the main points of interest along the Walk, its digital network - intangible infrastructure - is fragmented in terms of policies and contents. The goal of this study is to provide a comprehensive set of data and to propose the architecture and design for a circular dashboard of the SBW, capable of organizing information concerning the main features of the walk, in order to facilitate a shared governance for an effective tourism promotion.

Crisis environments, which are becoming systemic, pose significant challenges to smart government strategies. The paper aims to contribute to academic debate by proposing an analytical framework for examining the institutional capacities of smart government systems in addressing local crises. The paper focuses on the recent approach of robust governance and highlights a set of variables that promote effective smart government: contingency planning capacity, analytical capacity, organizational management capacity, and collaborative capacity. The study presents an analytical model for evaluating the robustness and effectiveness of local smart government systems in crises. One of the significant findings of this study has been the identification of critical indicators that inform institutional capacities of smart government systems. By analyzing these indicators, the proposed analytical framework provides a comprehensive approach to assess the preparedness of smart government systems in dealing with crises. Moreover, it can be used to benchmark the performance of local smart government systems in similar contexts and identify best practices for improving crisis management.

The global process of urbanization, and the modification of social interaction determined by the pandemic crisis poses the issue of the place of vulnerable users, and in particular children, within the contemporary city. This research aims to elaborate a theoretical and methodological framework, based on the concepts of affordance and capability, for analyzing the potential of public spaces to enable and support children’s independent activities. This potential, or meaningful usefulness, is expressed by the Index of Meaningful Usefulness of public Urban Spaces (IUIS). The latter is calculated via the tool ‘Opportunities for Children in Urban Spaces’ (OCUS). This methodology is applied to the analysis of significant public spaces within the historic center of the city of Iglesias in Sardinia, Italy. The results reveal adequate usefulness of the selected spaces, while underlining criticalities related to intrinsic spatial and physical attributes. The application to the case study confirms the validity of the theoretical and methodological framework embodied in the OCUS tool for supporting urban design and planning by orienting place-shaping processes towards the acknowledgement of children’s needs.