The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

Non-invasive continuous health monitoring has become feasible with the advancement of biosensors. While monitoring certain biomarkers such as heart rate or skin temperature are now at certain maturity, monitoring molecular biomarkers is still challenging. Progress has been shown in sampling, measurement and interpretation of data towards non-invasive molecular sensors that can be integrated in daily wearable items. Towards this goal, this paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. In controlled experiments, we have shown the variation of glucose concentration in water can be wirelessly detected by tracking the resonant frequency of the embroidered sensors. The current sensors operate at 1.8GHz–2GHz and respond to the change of glucose concentration with a sensitivity of 0.17 MHz/(mg/dl). The embroidered IDT-based sensors with wireless sensing will be a new measurement modality for molecular wearable sensors. The establishment of a wireless sensing mechanism for embroidered IDT-based sensors will be followed by investigation of sweat for molecular detection. This will require adding functionalities for sampling and interpretation of acquired data. We envisage the embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Smart City has emerged as the mainstream paradigm for urban governance innovation, sustainable development, and strategy upgrades, which is drawing attention from scholars worldwide. However, current frameworks for Smart City assessment remain incomplete and simplistic. In is paper, 30 national or provincial capitals in China were selected and we designed a tri-dimensional SPI model—Social, Physical, and Information Space—for smart city spatial development assessment. Utilizing methods such as entropy weighting, coupled coordination degree models, and the Dagum Gini coefficient, this study assesses the spatial development and coupled coordination of 30 cities from 2011 to 2019. Finally, by means of BP neural networks, the study examines the contribution of each indicator to the spatial coupled coordination. The results indicated that with a narrowing disparity in development speeds among different regions, the spatial coupled coordination development level of smart capitals in China has steadily increased, presenting a pattern of staggered distribution. Moreover, the IS subsystem plays the most significant role in coupled coordination. The significance of this research lies in its tri-dimensional spatial perspective of the spatial development and coupled coordination differences of the Smart City, providing evidence-based support for the regional layout and optimization in China.

Transportation plays an important role in urban development. Population growth and environmental burden have turned the efforts of cities globally towards smarter and greener mobility. Cooperative and Connected Automated Mobility (CCAM) serves as a concept with the power and potential to help achieve these goals building upon technological fields like Internet of Things, computer vision and distributed computing. However, its implementation is hindered by various challenges covering technical parameters such as performance and reliability in tandem with other issues, such as safety, accountability and trust. To overcome these issues, new distributed and decentralized approaches like blockchain and smart contracts are needed. This paper aims at identifying a comprehensive inventory of CCAM challenges and use it as a framework to describe methodologies using blockchain and smart contracts to address them. It provides a comparative analysis of the findings to draw useful conclusions and discuss future directions in CCAM and relevant blockchain applications. The paper contributes to intelligent transportation systems’ research by offering an integrated view of the difficulties in substantiating CCAM and providing insights on the most prominent blockchain and smart contract technologies that tackle them.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

Presence detection is essential in many applications, including smart homes, office automation, and public space management. Traditional technologies like infrared sensors and cameras frequently encounter obstacles due to privacy concerns, high costs, and complexity. The study provides a novel way to detect presence based on Wi-Fi signals and machine learning algorithms, utilizing the ESP8266 microcontroller. The suggested system attempts to reliably detect the presence of people in a given place by evaluating fluctuations in Wi-Fi signal strength and patterns. The theoretical basis of this strategy is investigated, including the ESP8266’s capabilities for Wi-Fi data gathering and the use of machine learning methods for data analysis. The methodology includes data collecting with the ESP8266, preprocessing, feature extraction, and training and evaluating machine learning models. This system’s potential uses include smart home automation, office occupancy tracking, and crowd management in public settings. The paper also discusses potential issues such as signal interference, data privacy concerns, and the limitations of Wi-Fi detection. Future work is also mentioned, including the suggested system’s installation and testing and enhancement proposals to improve accuracy and scalability. This research aims to provide a cost-effective, non-intrusive, and scalable presence detection system by harnessing the power of Wi-Fi signals and machine learning, enhancing intelligent environments

Protection suit is vital for fireman’ safety. Traditional protection suit just physically protects fireman from empyrosis, but can not locate the body injury position from the impact debris. Herein, we present a wearable impact debris positioning system for fireman protection suit alarming based on accelerometer array. The wearable piezoelectric accelerometers with distribute regularly on the suit to detect the vibration on different body parts, which is conducive to positioning injured body parts. In addition, the injured parts can be displayed on the dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11ms attributing to smart signal processing method. This work provides a reliable and smart method for locating and assessing the body injury position from the impact debris, which is significant for fire disaster commander to rescue injured fireman in time.

In an era marked by swift technological progress, the pivotal role of Artificial Intelligence (AI) is increasingly evident across various sectors, including local governments. These governmental bodies are progressively leveraging AI technologies to enhance service delivery to their communities, ranging from simple task automation to more complicated engineering endeavours. While more and more local governments are adopting AI, it is imperative to understand the functions, implications, and consequences of AI. Despite the growing importance of this domain, a significant gap persists within the scholarly discourse. This study strives to bridge this void by exploring the applications of AI technologies within the context of local government service provision and using this inquiry to generate lessons and best practices for similar smart city initiatives. Through a comprehensive grey literature review, we analysed 262 real-world AI implementations across 170 local governments worldwide. The findings underscore several key points: (a) There has been a consistent upward trajectory in the adoption of AI by local governments over the last decade; (b) Local governments from China, the US, and the UK are at the forefront of AI adoption; (c) Among local government AI technologies, Natural Language Processing and Robotic Process Automation emerge as the most prevalent ones; (d) Local governments primarily deploy AI across 28 distinct services; (e) Information management, back-office work, and transportation and traffic management are leading domains in terms of AI adoption. This study enriches the extant body of knowledge by providing an overview of existing AI applications within the sphere of local governance. It offers insights for smart city policymakers and decision-makers considering the adoption, expansion, or refinement of AI technologies in urban service provision. Additionally, it underscores the importance of using these insights to guide the successful integration and optimisation of AI in future smart city projects, ensuring they meet the evolving needs of communities.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

Artificial Intelligence (AI) and Deep Reinforcement Learning (DRL) have revolutionised e-learning by creating personalised, adaptive, and secure environments. However, challenges such as privacy, bias, and data limitations persist. E-FedCloud aims to address these issues by providing more agile, personalised, and secure e-learning experiences. This study introduces E-FedCloud, an AI-assisted adaptive e-learning system that automates personalised recommendations and tracking, thereby enhancing student performance. It employs federated learning-based authentication to ensure secure and private access for both course instructors and students. Intelligent Software Agents (ISAs) evaluate weekly student engagement using the Shannon Entropy method, classifying students into either engaged or not-engaged clusters. E-FedCloud utilises weekly engagement status, demographic information, and an innovative DRL-based early warning system, specifically ID2QN, to predict the performance of not-engaged students. Based on these predictions, the system categorises students into three groups: risk of dropping out, risk of scoring lower in the final exam, and risk of failing the end exam. It employs a multi-disciplinary ontology graph and an attention-based capsule network for automated, personalised recommendations. The system also integrates performance tracking to enhance student engagement. Data is securely stored on a blockchain using the LWEA encryption method.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

Information and Communication Technology (ICT) is at the heart of the Smart City approach, which constitutes the next level of cities’ and communities’ development across the globe. Thereby, ICT serves as the gluing component enabling different domains to interact with each other and facilitating the management and processing of vast amounts of data and information towards intelligently steering the cities infrastructure and processes, engaging the citizens and facilitating new services and applications on various aspects of urban life - e.g. supply chains, mobility, transportation, energy, citizens’ participation, public safety, interactions between citizens and the public administration, water management, parking and many other use cases and domains. Hence, given the fundamental role of ICT in cities in the near future, it is of paramount importance to lay the ground for a sustainable and reliable ICT infrastructure, which can enable a city/community to respond in a resilient way to upcoming challenges whilst increasing the quality of life for its citizens. This paper constitutes a continuation of a series of research documents and standardization activities, which relate to the concept of Open Urban Platforms (OUP) and the way they serve as a blueprint for each city/community towards the establishment of an ICT backbone. Thereby, the current paper emphasizes on the aspects of sustainability and resilient ICT, whilst reporting on our latest activities and related developments in the research area.

This paper addresses challenges and solutions in urban development and infrastructure resilience, particularly in the context of Japan's rapidly urbanizing landscape. It explores the integration of smart city concepts to combat land subsidence and liquefaction, phenomena highlighted by the 2011 Great East Japan Earthquake. Using advanced technologies such as smart sensing and predictive analytics through kriging and ensemble learning, the study aims to improve the accuracy of geotechnical investigations and urban planning. By analyzing data from 433 geotechnical surveys in Setagaya, Tokyo, it develops predictive models to accurately determine the depth of bearing layers critical to urban infrastructure. The results demonstrate the superiority of ensemble learning in predicting the depth of bearing layers, with significant implications for smart city development and the sustainability of urban environments. This interdisciplinary approach not only seeks to mitigate risks associated with geological disturbances, but also promotes sustainable urban growth that prioritizes safety and prosperity. Through advanced technology and comprehensive research, the study underscores the potential of smart cities to address urban complexities and ensure a resilient, sustainable future.

Intelligent cities or smart cities evolve bottom-up along with the digitisation and the creation of digital entities linked to human activities, physical space, and institutional settings of cities; but also, they progress top-down through smart city strategies and projects designed and implemented by public authorities. Yet, thirty-five years since the first use of the term “smart city” or “intelligent city” in the second half of the 1980s, and more than ten years of intense publications in this field, since 2009, there is still a great deal of fuzziness about the projects that make cities intelligent or smart. There is low awareness about the big differences between large, complex urban projects, such as ‘Zero Energy Districts’ or “Mobility-as-a-Service” and projects for automation of city infrastructures, such as smart city lighting, smart metering or finding a parking place. There is a widespread misconception that city intelligence or smartness, the core attribute of smart cities, can be achieved through automation of the city infrastructure. This paper focuses on projects that make cities intelligent or smart. Our intention is to show the complexity and effort needed to achieve this objective. It is an inquiry on projects and data from a large number of smart cities around the world. We analyse core properties of smart city projects, such as (a) interventions on the physical, social, and digital space of cities, (b) the relation to city sectors and ecosystems, (c) engagement of users and stakeholders in decision-making, and (c) impact through optimisation and innovation of city processes and routines. We discuss also projects we have designed and implemented in the framework of URENIO Research and ITI-CERTH. Our conclusions are two-fold. First, we propose a typology of smart city projects along 3 axes and 9 properties. Second, we argue that success and failure to achieve city smartness are mainly institutional. Most barriers to implementation are organisational, legal, and institutional. This can be explained by the social and institutional inertia of the urban system against new solutions, especially when innovation and radical change of existing routines take place. Change management should be a permanent companion of smart city projects implementation, and the modification of routines should be clearly defined and considered already at the design phase of projects.

This paper formulates the performance evaluation of cloud services as a multicriteria group decision making problem, and presents a fuzzy multicriteria group decision making method for evaluating the performance of cloud services. Interval-valued intuitionistic fuzzy numbers are used to model the inherent subjectiveness and imprecision of the performance evaluation process. An effective algorithm is developed based on the technique for order preference by similarity to ideal solution method and the Choquet integral operator for adequately solving the performance evaluation problem. An example is presented to demonstrate the applicability of the proposed fuzzy multicriteria group decision making method for solving the multicriteria group decision making problem in real world situations.

As technology advances, people are increasingly adopting IoT (Internet of Things) devices in smart cities. These devices are equipped with sensors that are connected everywhere, from energy infrastructure and transportation to telecommunications, health and human services, waste management, public safety, and more. People want to access sensor data anytime and everywhere to make better decisions and improve their lives. To achieve this, a sensor integration model has been developed where multiple sensors are integrated under one gateway to manage and share sensor data. However, effective sharing of sensor data requires data security, privacy, confidentiality, fairness, effective architectural design, and low communication and computation costs. These issues need to be addressed in the sensor integration model in smart cities. Existing storage models face challenges in managing sensor data effectively. To overcome these issues and hurdles, a data storage framework leveraging blockchain technology has been proposed within the sensor integration model. This framework ensures data security, privacy, confidentiality, and a fair and transparent financial model, all while minimizing communication and computation costs.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

Climate change and food security are the most relevant issues to be considered in sustainable agricultural development. The FAO’s initiative of climate-smart agriculture has attracted international attention. Since then, the smart agriculture (SA) has been recognized as the most influential trends in contributing to agricultural development. Therefore, encouraging farmers to adopt digital technologies and mobile devices into farming practices becomes a policy priority worldwide. However, there is limited literature available on psychologic factors that drive farmers’ intentions to adopt SA technologies. The purpose of this study is to investigate how farmer’s knowledge and attitude toward SA affects their adoption of smart technologies in Taiwan. A total of 321 farmers participated in the project’s survey in 2017 and 2018, from which the data was used to perform an OLS regression model of SA adoption. This study contributes to a preliminary understanding of relationship between innovation and adoption of SA technologies in a small-scale farming economic context. The findings suggest that the policy makers and R&D institutes need to concentrate on improving market access for well-known and high important SA technologies.

In response to increasing urbanization and the need for infrastructure resilient to natural hazards, this study introduces an AI-driven predictive model designed to assess the risk of soil liquefaction. Utilizing advanced ensemble machine learning techniques, the model integrates geotechnical and geographical data to accurately predict the potential for soil liquefaction in urban areas, with a specific focus on Yokohama, Japan. This methodology leverages comprehensive datasets from geological surveys and seismic activity to enhance urban planning and infrastructure development in smart cities. The primary outputs include detailed soil liquefaction risk maps that are essential for effective urban risk management. These maps support urban planners and engineers in making informed decisions, prioritizing safety, and promoting sustainability. The model employs a robust combination of neural networks and gradient boosting decision trees to analyze and predict data points, assessing soil susceptibility to liquefaction during seismic events. Notably, the model achieves high accuracy in predicting soil classifications and N-values, which are critical for evaluating soil liquefaction risk. Validation against an extensive dataset from geotechnical surveys confirms the model’s practical effectiveness. Moreover, the results highlight the transformative potential of AI in enhancing geotechnical risk assessments and improving the resilience of urban areas against natural hazards.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

During the last decade, smart materials have increasingly impacted on several niches, among which that of one-off/limited edition experimental fashion. Thanks to their performativity, due to the implementation of Smart Materials Systems, they have reached indeed catwalks as well as museums and galleries. As boundaries between what-is-art and what traditionally was not supposed to be art are now turning into osmotic membranes, zooming on how smart materials are highly contributing to outline the new creative landscape can provide with interesting and compelling issues. Introducing three different areas of experimental fashion, named Multi-sensory dresses, Empathic dresses, and Bio-smart dresses and accessories, respectively covering the world of in-Lab experiments and design collaborations in relation to the application of advanced smart materials systems, the article discuss some of the implications in term of Design Thinking and Design Aesthetics.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Multiple sensor nodes known as detection stations make the sensor networks; each node is light and portable. Every sensor node contains power source, microcomputer, transducer and transceiver. Power source provides power to each node. Micro-computer is used for storing and processing the output coming from the sensors. The transducer is used to generate the signals and the transceiver is used to receive and transmit data to the central computer. Eavesdropping gets facilitated with wireless communication, and it has many useful applications in military, homeland, hostile and uncontrolled environments. So it is prone to the high level of security. The process in which information is gathered to form a summarized type for analysis is known as data aggregation, as it is used to reduce the energy consumption in wireless sensor networks. The security issues have become crucial in data aggregation, especially when gets deployed in hostile and remote environment. In wireless sensor networks many secure aggregations have been proposed. It still faces some resource constrained that’s why new techniques are needed. In our survey we will discuss those approaches and their pros and cons.

With the rapid development of global offshore wind power, the demand for offshore wind power operation and maintenance is also increasing. Wisdomization of offshore wind farms is a practical need to improve the operation level and benefit of offshore wind farms. This paper first introduces the current development situation and characteristics of global offshore wind power, and expounds the current situation and main challenges of offshore wind power operation and maintenance market. Therefore, our paper discusses the innovation of offshore wind power operation and maintenance from the aspects of operation and maintenance management of offshore wind power, monitoring and analysis technology of units, far-reaching wind field monitoring and operation and maintenance risks. Then, combined with information technology and lean management concept, a smart operation and maintenance management platform for wind farms in far-reaching sea areas is built to explore centralized and intelligent operation and maintenance management mode, improve operation and maintenance efficiency of wind farms in far-reaching sea areas, and minimize operation and maintenance costs. Finally, through the research on the characteristics of 5G technology, combined with the practical experience of operation and maintenance, and in view of the characteristics of offshore wind farms, we analyze and propose several typical application scenarios of 5G technology in the intelligent operation and maintenance of offshore wind farms, which provides a new solution for the efficient operation and maintenance of offshore wind farms.

The escalating global population and subsequent demand for agricultural products have led to a surge in agricultural waste generation, posing significant disposal challenges. Conventional disposal methods such as burning and dumping not only harm the environment but also jeopardize human health and safety. Recognizing the urgent need for sustainable waste management, researchers have increasingly focused on repurposing agricultural plant waste as a valuable resource. This paper presents a comprehensive review of the potential of agricultural plant waste in wealth creation and sustainable development. It highlights the detrimental impacts of current disposal methods and emphasizes the necessity for alternative approaches. By analyzing the physical, mechanical, and chemical properties of plant fibers, particularly cellulose, hemicellulose, and lignin, this review underscores their suitability for diverse applications. Moreover, it explores the emerging trend of utilizing pineapple leaf fiber, a sustainable and lightweight material, in structural applications such as UAV construction. With its exceptional mechanical properties and biodegradability, pineapple leaf fiber holds promise as a viable alternative to traditional materials, contributing to a more sustainable future. In conclusion, this review advocates for a paradigm shift towards embracing agricultural plant waste as a valuable asset for economic prosperity and environmental sustainability. It underscores the importance of continued research and technological advancements to unlock the full potential of agricultural waste in fostering a circular economy and driving sustainable development globally.

Programmable Object Interfaces are increasingly intriguing researchers because of their broader applications, especially in the medical field. In Wireless Body Area Network (WBAN), for example, the patients’ health can be monitored using clinical nano sensors. Exchanging such sensitive data requires a high level of security and protection against attacks. To that end, the literature is rich with security schemes that include the advanced encryption standard, secure hashing algorithm, and digital signatures that aim to secure the data exchange. However, such schemes elevate the time complexity rendering the data transmission slower. Cognitive Radio technology with a medical body area network system involves communication links between WBAN gateways, server and nano sensors rendering the entire system vulnerable to security attacks. In this paper, a novel DNA-based encryption technique is proposed to secure medical data sharing between sensing devices and central repositories. It has less computational time throughout authentication, encryption, and decryption. Our analysis of experimental attack scenarios shows that our technique is better than its counterparts.

This paper investigates the periodic and quasi-periodic orbits in the symmetric collinear four-body problem through a variational approach. In Section 3, we analyze the conditions under which homographic solutions minimize the action functional. We demonstrate that these solutions for four equal masses arranged in a linear configuration are indeed the minimizers of the action functional and compute the minimum value of the action functional for these solutions. Additionally, we employ numerical experiments using Poincaré sections to explore the existence and stability of periodic and quasi-periodic solutions within this dynamical system. Our results provide a deeper understanding of the variational principles in celestial mechanics and reveal complex dynamical behaviors that are crucial for further studies in multi-body problems. The findings have significant implications for theoretical research and practical applications in astrodynamics and space mission planning.

The present work proposed a low-cost portable device as an enabling technology for Smart Farms using multispectral imaging and Machine Learning in soil texture. Clay is an important factor for the verification and monitoring of soil use due to its fast reaction to chemical and surface changes. The system developed uses the analysis of reflectance in wavebands for clay prediction. The selection of each wavelength is performed through an LED lamp panel. A NoIR microcamera controlled by a Raspberry Pi device is employed to acquire the image and unfold it in RGB histograms. Results showed an good prediction performance with R2 of 0.96, RMSEC of 3.66% and RMSECV of 16.87%. The high portability allows the equipment to be used in a field providing strategic information related to soil sciences.

This review paper aims to understand the current processing plant maintenance systems and further identify on-stream phased array corrosion mapping (PACM) to reduce turnaround maintenance (TAM) activity during plant operations. Reducing the TAM duration and extending the TAM interval are common goals of most researchers. Thus, a detailed review was performed to understand the maintenance systems and the problems faced. Furthermore, a review of the current PACM application and the possibility of applying it during on-stream inspection was also per-formed. PACM has better detectability for localized corrosion, and the results can be obtained for a range of thicknesses, which is the main advantage of this method. The challenge is to apply it to a surface with high temperatures, owing to the greater probe contact and the limitation of ultrasonic properties. This literature review provides a more precise direction for future research to evaluate PACM on piping that can be utilized in inspection during plant operation at elevated temperatures. Detecting and monitoring corrosion growth without shutdown.

Open-vocabulary learning has recently gained prominence as a means to enable image segmentation for arbitrary categories based on textual descriptions. This advancement has extended the applicability of segmentation systems to a broader range of generally purpose scenarios. However, current methods often revolve around specialized architectures and parameters tailored to specific segmentation tasks, resulting in a fragmented landscape of segmentation models. In response to these challenges, we introduce OVAMTSeg, a versatile framework designed for Open-Vocabulary and Multitask Image Segmentation. OVAMTSeg harnesses adaptive prompt learning to empower the model to capture category-sensitive concepts, enhancing its robustness across diverse multi-task and scenario contexts. Text prompts are employed to effectively capture semantic and contextual features of the text, while cross-attention and cross-modal interactions enable the fusion of image and text features. Furthermore, a transformer-based decoder is incorporated for dense prediction. Extensive experimental results underscore the effectiveness of OVAMTSeg, showcasing its state-of-the-art performance and superior generalization capabilities across three segmentation tasks. Notable achievements include a 47.5 mIoU in referring expression segmentation, 51.6 mIoU on Pascal-VOC with four unseen classes, 46.6 mIoU on Pascal-Context in zero-shot segmentation, 65.9 mIoU on Pascal-5i, and 35.7 mIoU on COCO-20i datasets for one-shot segmentation.

Software-Defined Networking (SDN) has revolutionized network management by providing unprecedented flexibility, control, and efficiency. However, its centralized architecture introduces critical security vulnerabilities. This paper presents an innovative approach to securing SDN environments using IOTA 2.0 smart contracts. The proposed system leverages the IOTA Tangle, a directed acyclic graph (DAG) structure, to enhance scalability and efficiency while eliminating transaction fees and reducing energy consumption. We introduce three smart contracts—Authority, Access Control, and DoS Detector—to ensure secure network operations, prevent unauthorized access, and mitigate denial-of-service attacks. Through comprehensive simulations using Mininet and the ShimmerEVM IOTA Test Network, we demonstrate the efficacy of our approach in enhancing SDN security. Our findings highlight the potential of IOTA 2.0 smart contracts to provide a robust, decentralized solution for securing SDN environments, paving the way for further integration of blockchain technologies in network management.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

The nutrient absorption and utilization efficiency in the roots of seedlings are beneficial for increasing crop yield. Creating marker assisted selection for wheat root traits can assist wheat breeders in choosing robust roots to maximize nutrient uptake. Exploring and identifying the effect of different nitrogen applications on RSA is of great significance for breeding nitrogen efficient wheat varieties. In this study, A total of 243 wheat varieties native to the Yellow and Huai Valley regions of China were utilized for genome-wide association studies (GWAS). Furthermore, a recombinant inbred line (RIL) population of 123 lines derived from the cross between Avocet and Chilero was utilized for linkage examination and confirmation of the hereditary loci distinguished by GWAS. Five RSA traits include the relative number of root tips (RNRT); relative total root length (RTRL); relative total root surface area (RTRS); relative total root volume (RTRV) and relative average root diameter (RARD) where evaluated under two N conditions—normal N (NN) supply and low N (LN)—to characterize the NUE of each accession. GWAS and linkage analysis were performed by integrating data from the wheat 660k single nucleotide polymorphism (SNP) chip and diversity arrays technology (DArT) to identify genetic loci associated with RSA. The results showed that based on the ratio of RSA related traits under two N supply conditions, a total of 598 SNP markers, which are significantly associated with RSA related traits, were detected at 160 genetic loci by GWAS. A total of 10 QTL loci related to RSA were dis-covered and identified by linkage mapping. In which, three significant RSA related Quantitative Trait Locus (QTL) were identified, namely qRtrl-3D, qRnrt-3D, and qRtrl-7D. The study has the potential to enhance the effectiveness of selecting root traits in wheat breeding programs, offering valuable insights into the genetic underpinnings of nitro-gen use efficiency (NUE) in wheat. This could lead to the creation of NUE wheat varieties by implementing focused breeding strategies.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

The world is struggling with the increasing rate at which water bodies are constantly polluted due to rapid modernization and industrialization. The different types of water contaminants include both anthropogenic and natural contaminants. Environmentalists are mainly concerned about heavy metals such as cadmium ions, as they are considered poisonous and carcinogenic even if they are present at a minimum concentration, and they are considered an immediate concern, according to the World Health Organization. Recently, many methods, such as solvent extraction, ion exchange, electrochemical precipitation, and reverse osmosis, have been developed to remove heavy metals from wastewater. These methods have been reported to be expensive and inefficient; hence, more cost-effective and eco-friendly alternative strategies are needed. Amidst these challenges, a ray of hope emerges in the form of biosorbents. These abundant, eco-friendly, and cost-efficient materials have shown promise as an alternative method for removing heavy metals from wastewater. They are equipped with functional groups that can effectively absorb metal ions onto their surfaces, offering a potential solution to our water contamination woes. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater

Cymbidium faberi Rolfe is one of the traditional Chinese orchids with important ornamental value, and the cultivation of Cymbidium faberi Rolfe mutant strains with different appearances is essential to increase its economic value, but at present, the acquisition of Cymbidium faberi Rolfe mutant strains basically relies on natural mutation.The objectives of this research were to mutagenize Cymbidium faberi Rolfe protocorm-like bodies (PLBs) and shoots in vitro using sodium azide (NaN3), and to screen and evaluate mutants in mutagenized Cymbidium faberi Rolfe seedlings using morphological characteristics.Cymbidium faberi Rolfe PLBs and shoots were used as mutagenic materials, and co-cultivated in induced shoots growth medium with the addition of 0.0 (control), 0.5, 1.0, 1.5, 2.0, 2.5, 3.0 mg/L and 0.0 (control), 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, and 10.0 mg/L NaN3 to induce the mutations, and the mortality rates of the PLBs and shoots were increased with the increase of the NaN3 concentration.At 14 d of co-cultivation, PLBs and shoots were most efficiently mutagenized with 1.5 mg/L and 4.0 mg/L NaN3, respectively.After the explants were cultured for 3 months, changes in leaf and flower morphology were observed in some mutants: shorter and thicker leaves, shorter node length, reduced height, and mid-translucent leaves compared with controls; and some Cymbidium faberi Rolfe bloomed prematurely, with single flowers with large, thick petal sepals and small inflorescences, and colours include light green throughout, and a few with purple stamens.This suggests that NaN3 can effectively mutagenise Cymbidium faberi Rolfe PLBs and shoots to satisfy people's demand for Cymbidium faberi Rolfe's ornamental properties while increasing its economic value.

Road cracks significantly affect the serviceability and safety of roadways, especially in mountainous terrain. Traditional inspection methods, such as manual detection, are excessively time-consuming, labor-intensive, and inefficient. Additionally, multi-function detection vehicles equipped with various sensors are expensive and not suitable for mountainous roads due to poor conditions. To address these challenges, this study proposes a customized Unmanned Aerial Vehicles (UAV) inspection system designed for automatic crack detection. The system focuses on enhancing autonomous capabilities in mountainous terrains by incorporating embedded algorithms for route planning, autonomous navigation, and automatic crack detection. The slide window method is proposed to enhance the autonomous navigation of UAV flights by generating path planning in mountainous roads. This method compensates for GPS/IMU positioning errors, particularly in GPS-denied or GPS-drift scenarios. Moreover, the YOLOv8 algorithm is introduced to conduct autonomous crack detection from UAV imagery in the offboard module. To validate our UAV inspection system's performance, we conducted several experiments to assess its accuracy, robustness, and efficiency. The experimental results demonstrate that our UAS inspection system accurately estimates the flight trajectory along the mountainous road for autonomous navigation. Furthermore, the experimental detection results also demonstrate that the YOLOv8 algorithm achieves higher recognition accuracy compared to the YOLOv5, and YOLOv7-tiny algorithms, exceeding 3.1%,and 6.8% of mAP, respectively. In summary, the UAV inspection system proposed in this study can provide a useful tool and technological guidance for the regular inspection of mountainous roads.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Statistical denoising techniques have been well studied, however many challenges still remain. This 9 article focuses on determining the least necessary number of significant samples in a statistical pop-10 ulation sampling, while minimizing the impact on the statistical detection of the fiber Bragg grating 11 (FBG) power spectra. This is achieved by using Bayesian decision making, small population statis-12 tics while excluding false detection. First, we investigate the impact of two-sided sliding window 13 technique applied near the cell under the test. The window size varies from 8 to 60 samples. The 14 considered maximum size of population sampling is connected with the number of wavelength 15 samples within the bandwidth of the symmetrical FBG power spectra peaks. Regarding the sym-16 metry of FBG power spectra peaks and the possible reduction of computational demands, we inves-17 tigate the impact of a one-sided sliding window. This enables to achieve less processing latency for 18 real time applications thus brings benefits to FBG-based fiber optical sensing. Both, two- and one-19 sided small population sampling techniques are then experimentally verified. Detection results are 20 analyzed in depth via calculating detection thresholds by using the small size window sliding along-21 side the waveband. From results achieved, it was found that the normality three-sigma rule does 22 not need to be followed while using the small population sampling. Experimental demonstrations 23 and analyses showed that the proposed concept of denoising and statistical threshold detection 24 based on the sliding window does not depend on the prior knowledge of probability distribution 25 functions of the FBG power spectra peaks level and background noise. We have also found that the 26 thresholds’ adaptability mainly depends on the statistical numerical characteristics of the above ad-27 ditive mixture of the FBG power spectra peaks signals and background noise.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

Iron tailings are solid waste generated after the mining of iron mines, which have caused serious damage to the surrounding ecology and environment and have attracted widespread attention. By analyzing the formation causes, main components, and environmental effect mechanisms of iron tailings, the article systematically elaborates on the degree and mechanism of the harm of iron tailings to water bodies, atmosphere, soil, and ecosystems, and evaluates its impact on human health and sustainable development of society. On this basis, specific prevention and control measures have been proposed to reduce iron tailings emissions, realize resource recycling, and restore ecosystems. Research shows that iron tailings containing heavy metals can widely pollute the environment through dissolution and migration, and have significant biological toxicity effects. The research results can provide a theoretical reference for decision-making departments to formulate scientific and reasonable iron tailings disposal and ecological protection policies. It is recommended to strengthen specific research on the infiltration of toxic and harmful components in tailings in the future, and develop efficient and stable solidification technology, and vegetation-microbial joint restoration models to further reduce the ecological and environmental risks of iron tailings.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

X-ray Fluorescence Computed Tomography (XFCT) is an emerging non-invasive imaging technique providing molecular-level data, gaining attention for high-resolution imaging. However, increased sensitivity with benchtop X-ray sources raises radiation exposure. Artificial Intelligence (AI), particularly deep learning (DL), has revolutionized medical imaging by delivering high-quality images in the presence of noise. In XFCT, traditional methods rely on complex algorithms for noise reduction, but AI holds promise in addressing high-dose concerns. We present an optimized SCUNet model for noise reduction in low-concentration XRF images. Compared to higher-dose images, our method’s effectiveness is evaluated. While various denoising techniques exist for X-ray and CT, few address to XFCT. The DL model is trained and assessed using the augmented data, focusing on background noise reduction. Image quality is measured using PSNR and SSIM, comparing outcomes with 100% X-ray dose images. Results show the proposed algorithm achieves high-quality images from low-dose and low-contrast agents, with a maximum PSNR of 39.05 and SSIM of 0.86. The model outperforms BM3D, NLM, DnCNN, and SCUNet in both visual inspection and quantitative analysis, particularly in high-noise scenarios. This indicates the potential of AI, specifically the SCUNet model, in significantly improving XFCT imaging by mitigating the trade-off between sensitivity and radiation exposure.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

To achieve n-type doping in diamond, extensive investigations employing first principles have been conducted on various models of phosphorus doping and boron-phosphorus co-doping. The primary focus of this study is to comprehensively analyze the formation energy, band structure, density of states, and ionization energy of these structures. It is observed that within a diamond structure solely composed of phosphorus atoms, the formation energy of an individual carbon atom is excessively high. However, the substitution of two carbon atoms leads to the conversion of diamond into a p-type semiconductor. Upon examining the P-B co-doping structure, it is revealed that the doped impurities exhibit a tendency to form more stable cluster configurations. As the separation between the freely doped atoms and the cluster impurity structure increases, the overall stability of the structure diminishes, consequently resulting in an elevation of the ionization energy. Analysis of the electronic density of states demonstrates that the electron orbit of the B atom makes negligible contributions to the impurity levels during P-B doping.

With the ongoing amendment of the EU legislation on the treatment of urban wastewater, stricter requirements for the removal of pollutants are expected, which calls for the need for innovative wastewater treatment technologies. Biological systems are still the first choice. The survey of typical bioreactors applied in wastewater treatment is presented. Wastewater treatment objective, bio-chemical environment and microbial growth are selected as a main criterion for classification of these bioreactors. Hydraulic and kinetic aspects are considered, advantages and drawbacks of these bioreactors regarding the selection of appropriate type of the reactor as well as regarding operation of reactors are mentioned. The aim of this paper is to provide operators and designers with a brief overview of selected traditional and advanced processes, reactors, and technologies for nutrient removal from municipal wastewater. Another goal is to discuss the possibilities and limitations to comply with more strict effluent standards. From the evaluation of the published papers, it follows that the currently applied traditional methods of nutrients removal have the potential to convey also with the expected stricter limits.

Lactoperoxidase (LP) is an important enzyme of the salivary and mammary glands. It has been proven to increase the shelf life of raw milk by inhibiting the growth of bacteria, especially Listeria monocytogenes, Escherichia coli, Staphylococcus aureus, and Pseudomonas spp. The aim of this work was to verify the use of LP to extend the shelf life of meat products. In vitro experiments showed inhibitory effects against selected bacteria (Listeria innocua (ATCC 33090), Staphylococcus saprophyticus (CP054440.1), and Pseudomonas fluorescens (ATCC 13525) due to prolongation of the lag phase of growth curves. A lower increase in viable counts (P &lt; 0.05) was also found by testing the pork cubes surface treated with LP solution (5%) + L. innocua and stored for 7 days at 15 °C. LP has also been studied at concentrations of 0.25 and 0.50% in meat products (pork ham and pâté) during refrigerated storage (4 °C for 28 days). Lower viable counts were observed throughout the storage experiment, especially for 0.50% LP (P &lt; 0.05). Meat products containing LP also showed lower levels of oxidation (MAD) (P &lt; 0.05). According to these results, LP could extend the shelf life of a wider range of products.

Agriculture contributes towards South African economy, but this sector is highly vulnerable to risks imposed by climate change. Smallholder maize farmers are specifically susceptible to climate change impacts. Maize crop plays a crucial role in the country's food security as it is considered a stable food for households and source of feed for livestock. The study aimed to analyze the socio-economic factors influencing smallholder maize farmers’ willingness to adopt climate-smart agriculture. It was conducted in three different areas due to their specific agro-ecological zones. Multipurpose research design was used to gather data, and multistage random sampling to choose the study areas. Subsequently, 209 purposively selected farmers were interviewed face-to-face using structured questionnaires and focus discussion groups. Descriptive statistics and Double-hurdle regression model were used to analyze the data. Descriptive results indicated that 81%, 67%, and 63% farmers were willing to adopt CSA in Ga-Makanye, Gabaza, and Giyani, respectively. Empirical results from the first and second hurdles of the regression analysis showed that farmers’ education, crop diversification, information about CSA positively influenced the decision to adopt CSA while household size and agricultural experience negatively influenced the decision to adopt CSA. It is recommended that the Department of Agriculture, Land Reform, and Rural Development should provide CSA workshops and educational programs to farmers to enhance their knowledge and decision-making processes regarding adaptation strategies.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

Developing and utilising of underground space is an vital direction for urban growth. Underground commercial streets, as a significant component of underground space accommodating extensive human social activities, and consequently necessitate the creation of human-scale spaces. In the evolution of urban design development towards greater refinement, applying architectural theories and excessively subjective designs has resulted in a deficiency of human-centered design and a disordered spatial environment. This study merges environmental psychology and architectural theory to determine the appropriate length of spatial scale. Two experiments focusing on spatial perception evaluation were conducted using a virtual experimental platform that featured varying dimensions of spatial scale combinations. These quantified combinations were correlated with perception evaluation, and regression analysis was employed to identify appropriate scale ranges, which were superimposed on the range of length selection. Finally, the optimal length and scale combination for underground commercial street spaces were established, providing a reference for the human-centered design of these environments.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Despite the partial disclosure of driving scenario knowledge graphs, they still fail to meet the comprehensive needs of intelligent connected vehicles for driving knowledge. Current issues include the high complexity of pattern layer construction, insufficient accuracy of information extraction and fusion, and limited performance of knowledge reasoning models. To address these challenges, a hybrid knowledge graph method was adopted in the construction of the Driving Scenario Knowledge Graph (DSKG). Firstly, core concepts in the field were systematically sorted and classified, laying the foundation for the construction of a multi-level classified knowledge graph top-level ontology. Subsequently, by deeply exploring and analyzing the Traffic Genome data, 34 entities and 51 relations were extracted and integrated with the ontology layer, achieving the expansion and updating of the knowledge graph. Then, in terms of knowledge reasoning models, an analysis of the training results of the TransE, Complex, Distmult, and Rotate models in the entity linking prediction task of DSKG revealed that the Distmult model performed the best in metrics such as hit rate, making it more suitable for inference in DSKG. Finally, a standardized and widely applicable Driving Scenario Knowledge Graph was proposed. The DSKG and related materials have been publicly released for use by industry and academia.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

(S)-Atenolol ((S)-2-(4-(2-Hydroxy-3-(isopropylamino)propoxy)phenyl)acetamide) has been synthesized in >99% ee with use of Candida antarctica lipase B from Syncozymes (Shanghai, China), in a kinetic resolution of the corresponding racemic chlorohydrin. Deprotonation of the starting phenol building block was base catalyzed. The enantiopurity of the chlorohydrin building block remained unchanged upon subsequent amination. All four steps in the synthesis protocol have been optimized compared to previously reported methods, which makes this new protocol more sustainable and in accordance with green chemistry principles compared to previously reported protocols.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

The publication presents an innovative tower cultivation device designed to significantly increase vertical farming efficiency. The device divides the cultivation system into separate chambers. One division corresponds to the different growth phases of the plants, while another reflects the daily variation in conditions. Each chamber presents slightly different conditions and cultivation patterns from the others. For the early stages, crops are grown horizontally in trays once they mature, transplanted into mobile cultivation towers. The closed circulation of ventilation and irrigation reduces water consumption by up to 95%. A unique separate day-night division optimises light, temperature and humidity conditions, mimicking natural growth patterns. This approach not only saves water and energy but also optimises cultivation in a three-dimensional space. The presented solution focuses on the often overlooked aspects of cultivating in vertical farms and makes this method of growing much more cost-effective and feasible to implement on a large scale.

It has been demonstrated that cancer cells that have survived cancer treatment may be more malignant than the original cancer cells. These cells are considered to be the main cause of metastasis in prognosis. A Nanog-overexpressing colon-26 (Nanog+colon26) was generated and its metastatic potential was confirmed to be enhanced, indicating higher malignancy. Extracellular vesicles (EVs) secreted from the cell line (Nanog+colon26EVs) were administered to mice at 5 μg nine times (three times per week for three weeks) via the tail vein (PBS was used as a control). Subsequently, Nanog+colon26 cells were administered to mice via the spleen, and the quantity of metastatic colonies in the liver was analyzed two weeks later. The results demonstrated that the administration of EVs suppressed metastasis. The enhanced phagocytic activity of macrophages observed in the group treated with Nanog+colon26EVs indicated the involvement of the immune system in the observed metastasis-suppressing effect. Small RNA sequencing was conducted to identify Nanog-dependent miRNAs that exhibited significant changes (Fc>=1.5 or Fc

Rapidly digestible starch can be obtained by gelatinization (cooking), cooking extrusion, use of small granule starch, breaking down starch granules, or by hydrolysis to maltodextrins. Resistant starch includes five groups: the first group is physically encapsulated starch within a food/polymer matrix, the second one is some native starch, the third one is recrystallized starch, the fourth one is chemically modified starch, and the fifth one is starch-lipid complexes. Starch digestion in the human body is also influenced by the degree of chewing, activity of α-amylase in the intestine, and transit time through the stomach and small intestine. Resistant starch or dietary fiber (DF) enriches specific bacterial groups located in the large intes-tine. They produce short chain fatty acids (SCFAs) and gases, causes the lowering of the pH, and inhibits pathogens. SCFAs are considered endogenous signaling molecules, acting through their free fatty-acid receptors 2 and 3 which can trigger the secretion of glucagon-like peptide-1 and peptide PYY, being released together following a meal to mediate postprandial satiety. A sufficient intake of DF reduces the risk of cardiovascular disease, coronary heart disease, stroke, hyperten-sion, colorectal cancer, and type 2 diabetes. Gluten matrix or phenolic compounds can lead to a low digestion rate of starch.

Glioblastoma (GBM) is the most common malignant brain tumor in adults. Despite advancements in treatment, the prognosis for patients with GBM remains poor due to its aggressive nature and resistance to therapy. CRISPR-based genetic screening has emerged as a powerful tool for identifying genes crucial for tumor progression and treatment resistance, offering promising targets for tumor therapy. In this review, we provide an overview of the recent advancements in CRISPR-based genetic screening approaches and their applications in GBM. We highlight how these approaches have been used to uncover genetic determinants of GBM progression and susceptibility to various therapies. Furthermore, we discuss ongoing challenges and future directions of CRISPR-based screening methods in advancing GBM research.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

The high flammability and lack of charrability of polystyrene (PS) pose significant limitations on its broader applications. Therefore, there is an urgent need for a straightforward and efficient method for the synthesis of flame-retardant PS, which still poses a considerable challenge. In this study, we present an efficient approach to enhance the flame-retardant properties of PS through direct phosphorylating aromatic C(sp2)-H bonds using commercially available and inexpensive manganese catalyst. A range of phosphonates served as reactive substrates to enable a tunable degree of polymer functionalization. The corresponding phosphorylated PS specimens were determined by means of 1H NMR, 31P NMR, FTIR spectroscopy and GPC. Microscale combustion calorimetry (MCC) tests indicate that this protocol indeed enhances the flame-retardant performance of PS. Moreover, other advantages associated with the incorporation of the phosphonate group have been observed, including improved thermal resistance and wettability. This cost-effective strategy of Mn-catalyzed C-H can also be utilized to directly obtain phosphonate modification of waste foamed PS and styrene acrylonitrile copolymer, providing a new method for the purpose of recycling and upgrading PS plastics.

Problem:Palestinian demographic landscape is undergoing an increase in the elderly population like many regions across the world. The elderly Palestinians face a unique challenges and problems of limited access to traditional care due to restricted movement, checkpoints, and also for limited healthcare resources. Therefore, the need arose to develop a sensitive and adaptable smart health monitoring system for Palestinian elderly to provide accurate and timely health data to improve well-being and prevent complications. Method: The proposed system (SHMS) leverages the Internet of Things (IoT) with appropriate sensors to track vital signs like heart rate, blood oximeter, body temperature and signal from a patient heart. Advanced algorithms analyze the data, generating alerts for potential health risks, triggering timely interventions, and enabling remote consultations. Results: This system has the potential to contributes to SDG 3 to significantly improve the health and well-being of elderly Palestinians by providing an accurate, low-power, and low-cost system for remote health monitoring. The system, being wearable, reads vital signs in real-time, overcoming geographical barriers and facilitating remote monitoring, especially in areas with limited healthcare centers and suffered from barriers along the way. The Doctor can suggest the patient’s prescription needed based on the momentary condition of the elderly and on previous readings of the sensors, if necessary. Which will also be notified via messages. Moreover, the doctor can take immediate intervention in case of an emergency. By implementing the system, it will be unnecessary for more than 50\% of the elderly to visit health care, thus reducing the cost to 50\%.}

Smart living, a concept that has gained increasing attention in recent years, revolves around integrating advanced technologies in homes and cities to enhance the quality of life for citizens. Sensing and human action recognition are crucial aspects of this concept. Smart living applications span various domains, such as energy consumption, healthcare, transportation, and education, which greatly benefit from effective human action recognition. This field, originating from computer vision, seeks to recognize human actions and activities using not only visual data but also many other sensor modalities. This paper comprehensively reviews the literature on human action recognition in smart living environments, synthesizing the main contributions, challenges, and future research directions. This review selects five key domains: Sensing Technology, Multimodality, Real-time Processing, Interoperability, and Resource-Constrained Processing, as they encompass the critical aspects required for successfully deploying human action recognition in smart living. These domains highlight the essential role that sensing and human action recognition play in successfully developing and implementing smart living solutions. This paper serves as a valuable resource for researchers and practitioners seeking to explore further and advance the field of human action recognition in smart living.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

This study evaluates the efficiency of biodegradable polyurethane foams as thermal insulation materials compared to conventional materials like expanded polystyrene (EPS). Key parameters analyzed include thermal conductivity, energy savings, CO2 emission reductions, and investment payback periods. Biodegradable polyurethane foams demonstrated a thermal conductivity of 0.022 W/(m·K), significantly lower than EPS's 0.035 W/(m·K), leading to higher energy savings. Calculations reveal an annual energy saving of 443,820 kWh for polyurethane foams, compared to 441,330 kWh for EPS. Financially, polyurethane foams save approximately €53,258.4 annually, while EPS saves €52,959.6. In terms of environmental impact, polyurethane foams reduce CO2 emissions by 88,764 kg annually, versus 88,266 kg for EPS. Despite the higher initial cost of polyurethane foams (€50/m² compared to €30/m² for EPS), the payback period is remarkably short at 0.094 years (1.13 months) compared to EPS's 0.057 years (0.68 months). These findings highlight biodegradable polyurethane foams as a superior option for thermal insulation, offering significant energy, financial, and environmental benefits.

The imperative to achieve carbon neutrality has driven significant advancements in the construction sector, particularly in the production and utilization of building materials. This paper explores innovative strategies and practices designed to reduce the carbon footprint of construction materials, with a focus on both the production processes and the application of sustainable materials. Key innovations include the development of low-carbon and carbon-negative materials, the integration of renewable energy sources in production, and the implementation of advanced recycling technologies. Case studies of successful projects demonstrate how these strategies can be applied in real-world scenarios, highlighting both the benefits and challenges encountered. The analysis also delves into the technical and economic aspects of these innovations, addressing the barriers to their widespread adoption and proposing solutions to overcome these challenges. Through a comprehensive examination of current practices and future trends, this paper aims to provide a roadmap for the construction industry to achieve carbon neutrality, contributing to broader climate change mitigation efforts and fostering a more sustainable built environment.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

Wearable Biosensor Technology (WBT) has emerged as a transformative tool in the educational system over the past decade. This systematic review encompasses a comprehensive analysis of WBT utilization in educational settings over a 10-year span (2012-2022), highlighting both the evolution of this field and its integration to address challenges in education by integrating technology to solve specific educational challenges, such as enhancing student engagement, monitoring stress and cognitive load, improving learning experiences, and providing real-time feedback for both students and educators. By exploring these aspects, the review sheds light on the potential implications of WBT for the future of learning. A rigorous and systematic search of major academic databases, including Google Scholar and Scopus, was conducted in accordance with PRISMA guidelines. Relevant studies were selected based on predefined inclusion and exclusion criteria. The articles selected were assessed for methodological quality and bias using established tools. The process of data extraction and synthesis followed a structured framework. Key findings include the shift from theoretical exploration to practical implementation with the EEG being the predominant measurement, aiming to explore mental states, physiological constructs, and teaching effectiveness. Wearable biosensors are significantly impacting the educational field, serving as an important resource for educators and a tool for students. Their application has the potential to transform and optimize academic practices through sensors that capture biometric data, enabling the implementation of metrics and models to understand the development and performance of students and professors in an academic environment, as well as to gain insights into the learning process.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

Cloud-induced atmospheric extinction and occlusion have a major effect on the effectiveness and quality of telescope observations. Real-time cloud cover distribution and long-term statistical data are essential for astronomical siting and telescope operations. At ground-based astronomical telescope sites, cloud cover distribution is currently analyzed using manual observation methods. However, the main disadvantages of manual observation methods are human subjective, heavy workloads and poor real-time performance. Therefore, a real-time automatic cloud images classification method is desperately needed. This paper presents a new cloud identification method, which is named PSO+XGBoost model by combining eXtreme Gradient Boosting (XGBoost) and Particle Swarm Optimization (PSO). The entire cloud image is divided into 37 sub-regions in order to more precisely identify the distribution of the clouds. 19 features are then extracted, including the sky background, star density, lighting conditions, and subregion grayscale values. The experimental results have shown that the overall classification accuracy of 96.91% and our model is able to outperform several state-of-the-art baseline methods. Our approach achieves high accuracy in comparison with the manual observation methods. Moreover, this method meets telescope real-time scheduling requirements.

Sentiment analysis plays a crucial role in understanding customer feedback, guiding product development, and informing business decisions. This paper introduces term sentiment entropy (TSE), a novel weighting method that leverages the distribution of sentiment labels associated with words to enhance text classification accuracy. TSE complements traditional TF-IDF techniques by capturing the nuances of sentiment variation across different contexts. Experiments across diverse public datasets demonstrate TSE's potential to improve sentiment analysis performance, especially in capturing subtle sentiment shifts and adapting to specific domains. While computational cost and label quality pose challenges, TSE offers a promising avenue for refining sentiment analysis and opening new research frontiers.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

This review paper presents a comprehensive synthesis of current knowledge on the contamination of water systems by polycyclic aromatic hydrocarbons (PAHs). PAHs, organic contaminants characterized by two or more fused aromatic rings, are notably problematic due to their persistence, bioaccumulation, and significant health risks. The review commences with an examination of various sources of PAHs in aquatic environments, encompassing both anthropogenic activities, such as industrial discharges, urban runoff, and oil spills, and natural phenomena including volcanic eruptions and wildfires. Subsequently, the discussion shifts to the distribution patterns of PAHs within different aquatic ecosystems, with an analysis of factors that influence their transport. Considerable focus is placed on the entry mechanisms of PAHs into water systems and their interactions with diverse environmental matrices. Additionally, the ecotoxicological effects of PAHs on aquatic life are scrutinized, with particular emphasis on molecular, individual, and ecosystemic impacts. This includes an exploration of PAH bioaccumulation in aquatic organisms and their potential mutagenic and carcinogenic consequences. The review further addresses the challenges associated with detecting and quantifying PAHs in aquatic settings, reflecting on the advancements in analytical methodologies and the complexities introduced by their varied physicochemical properties. The paper concludes with a summary of existing regulatory frameworks and guidelines governing PAH contamination in water systems, underscoring the imperative for global collaboration in the monitoring and management of PAH pollution.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

Fluidized beds are pivotal in the process industry and chemical engineering, with Computational Fluid Dynamics (CFD) playing a crucial role in their design and optimization. Challenges in CFD modeling stem from the scarcity or inconsistency of experimental data for validation, along with the uncertainties introduced by numerous parameters and assumptions across different CFD codes. This study navigates these complexities by comparing simulation results from the open-source MFIX and OpenFOAM, and the commercial ANSYS FLUENT, against experimental data. Utilizing a Eulerian-Eulerian framework and the kinetic theory of granular flow (KTGF), the investigation focuses on solid-phase properties through the classical drag laws of Gidaspow and Syamlal-O’Brien across varied parameters. Findings indicate that ANSYS Fluent, MFiX, and OpenFOAM can achieve reasonable agreement with experimental benchmarks, each showcasing distinct strengths and weaknesses. The study also emphasizes that both the Syamlal-O’Brien and Gidaspow drag models exhibit reasonable agreement with experimental benchmarks across the examined CFD codes, suggesting a moderated sensitivity to the choice of drag model. Moreover, the analysis were also carried out for 2D and 3D simulations, revealing that the dimensional approach impacts the predictive accuracy to a certain extent, with both models adapting well to the complexities of each simulation environment. The study highlights the significant influence of restitution coefficients on bed expansion due to their effect on particle-particle collisions, with a value of 0.9 deemed optimal for balancing simulation accuracy and computational efficiency. Conversely, the specularity coefficient, impacting particle-wall interactions, exhibits a more subtle effect on bed dynamics. This finding emphasizes the critical role of carefully choosing these coefficients to effectively simulate the nuanced behaviors of fluidized beds.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

This article provides a detailed analysis of non-invasive techniques for prediction and diagnosis of faults in internal combustion engines, focusing on the application of the Proknow-C and Methodi Ordinatio systematic review methods. Initially, the relevance of these techniques in promoting energy sustainability and mitigating greenhouse gas emissions is discussed, aligning with the Sustainable Development Goals (SDGs) of Agenda 2030 and the Paris Agreement. The systematic review conducted in the subsequent sections offers a comprehensive mapping of the state-of-the-art, highlighting the effectiveness of combining these methods in categorizing and systematizing relevant scientific literature. The results reveal significant advancements in the use of artificial intelligence (AI) and digital signal processors (DSP) to enhance fault diagnosis, as well as underscore the crucial role of non-invasive techniques in minimizing interference in monitored systems. Finally, concluding remarks point towards future research directions, emphasizing the need to develop digital twins for internal combustion engines and identify gaps for further improvements in fault diagnosis and prediction techniques.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.