A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

This paper addresses the evolving landscape of electricity markets in Europe, with a focus on the integration of Renewable Energy Communities as introduced by the Renewable Energy Directive 2018/2001. Residents within a postal code area are highly incentivized to join a community, which enables them to exchange energy among themselves at lower procurement costs. Thereby, energy management systems optimize the operation of respective energy systems, with electrical load forecasting playing a key role. Given that prosumers may switch between communities on a daily basis, electricity demands within these groups will vary, leading to data that is non-stationary, discontinuous as well as non-identical and independently distributed. To encounter this issue, we propose a sophisticated forecasting model that applies federated learning, using informations from various distributed communities to learn domain-invariant features. To achieve this, we initially utilize synthetic electrical load time series at district level and aggregate them to profiles of Renewable Energy Communities with dynamic portfolios. Subsequently, we develop a forecasting model that accounts for the composition of residents of a Renewable Energy Community, adapt data pre-processing in accordance with the time series process, and detail a federated learning algorithm that incorporates weight averaging and data sharing. Following the training of various experimental setups, we ultimately evaluate their effectiveness. The findings suggest that our proposed framework is capable of effectively forecast non-stationary and discontinuous time series and that it can be applied to new, unseen data through the integration of knowledge from multiple sources.

The decarbonization of the electricity grid as one among the actions to reduce fossil fuel emissions, and thus their impact on global warming in the future, will be achieved mainly via the integration and widespread diffusion of renewable power sources. This is going to be supported also by the shift from the paradigm production-transmission-distribution, where electricity production oversees large-size power plants, to renewable-based distributed/diffused production, where electricity is generated very close or even by the same (group of) user(s) (or prosumers in the latter case). The number of mid-/small-size installations based on renewable energy technologies will therefore increase substantially, and the related renewable generation will be dominant against that from large-size power plants. Unfortunately, this will reduce the reliability of the grid very likely, unless appropriate countermeasures are taken/implemented, hopefully at the same time the paradigm shift is being achieved. To this aim, it is important to identify the anomalies and main fault causes that might determine in renewable-based power systems. This paper surveys the current state-of-the-art on anomalies and faults affecting wind-PV-storage hybrid power systems, i.e., the main renewable technology ensemble that will establish the future grid, and highlights possible research directions that may help to fill the literature gaps.

Polar stratospheric clouds (PSCs) form in polar regions typically between 15 and 25 km, when the local temperature is sufficiently low. PSCs play an important role in the ozone chemistry and the dehydration and denitrification of the stratosphere. Lidars with a depolarization channel may be used to detect and classify different classes of PSCs. The main PSC classes are water ice, nitric acid trihydrate (NAT) and supercooled ternary solutions (STS), the latter being liquid droplets consisting of water, nitric acid and sulphuric acid. PSCs have been observed at the lidar observatory at Concordia Station from 2014 on. The harsh environmental conditions at Concordia during winter render successful lidar operation difficult. In order to facilitate the operation of the observatory several measures have been put in place to achieve an almost complete remote control of the system. PSC occurrence is strongly correlated with local temperatures and is affected by dynamics, as the PSC coverage during the observation season shows.

Chronic stress, culminating in burnout, evolves gradually and is notoriously difficult to detect due to vague symptoms and individuals' hesitance to acknowledge their struggles. To expedite the identification and recognition of this condition, enabling timely psychological intervention, the integration of Artificial Intelligence (AI) is increasingly considered. This research does not assert the feasibility of an AI system managing all aspects of chronic stress's impact. However, it highlights the capability of current technology to detect stress indicators based on quantifiable data like Heart Rate (HR) and organizational climate dimensions. Although other physiological markers such as oximetry, skin galvanic response, and EKG have been explored, they have not shown reliable differentiation between stress and joy. Focused on the unique context of school principals in the Bedouin regions of Israel, this study investigates the interplay between HR, organizational climate, and stress levels. It introduces a novel application of a fuzzy logic tool that combines HR and organizational climate metrics to aid in stress diagnosis. This tool incorporates the psychologist's expertise to provide real-time data crucial for developing effective coping strategies. While the AI-supported fuzzy system does not replace professional psychological intervention, it significantly enhances the speed of condition identification and intervention planning, thus shortening the response time to stress-related issues in educational leadership within culturally specific settings. The application of such AI-driven tools is pivotal for sustaining the well-being and effectiveness of educational leaders, thereby supporting the broader goal of educational sustainability.

Climate change presents an urgent global challenge, manifesting in rising temperatures and extreme weather events with severe societal impacts. The Eastern Mediterranean, warming faster than the global average, faces immediate repercussions. Climate literacy emerges as pivotal, empowering individuals to comprehend climate science and act accordingly. This study delves into climate literacy, attitudes, and 'greening' behaviours in the Eastern Mediterranean hotspot of Greece, based on a survey of 1,962 citizens. Findings indicate high climate literacy but lower adoption of 'greening' behaviours, especially those involving financial costs. Regression analyses highlight the significant role of climate literacy, concerns about personal impacts, coping appraisal and trust in institutions in promoting 'greening' behaviours. The study underscores the need for multifaceted strategies emphasizing financial motivation, trust-building, and societal norm shifts. Socio-demographic disparities, including gender and occupation, highlight areas for targeted interventions. The emphasis on the mental health impacts of climate-related events underscores the need for holistic disaster management. Policy implications are discussed, highlighting the potential of expanded climate literacy to catalyze collective action toward sustainability.

The effects of climate change health impacts on urban health care systems and vulnerable populations are a researched topic with foundations on urban risk management, urban health methodologies, and sustainable urbanization. As climate change is a dynamic and transformative global issue the gap between adaptation and mitigation efforts and urban planning relies, among other things, in the limitations of previous studies of risk management structures tailored to the existing strategy to calculate the uncertainties and predict their influence on urban systems and subsystems. Moreover, as climate and health is a well-researched issue, it is also complex as the methodologies and strategic approach to minimize health risks of climate change is intrinsically contingent to risk methodologies and policy-making processes that are efficient with support of knowledge-based information. This paper emphasis the need for focusing on urban health risk management methods that serves to identify potential opportunities, and then manage and take action to prevent adverse health effects. It also emphasizes the probability of events and their consequences, which are measurable both qualitatively and quantitatively.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

The study examines projected changes in dry- and wet-spell probabilities in West Africa using a Markov chain approach. Four simulations of regional climate models from the CORDEX-Africa program were used to analyze projected changes in intraseasonal variability. The results show an increase in the probability of having a dry day, a dry day preceding a wet day and a dry day preceding a dry day, and a decrease in the probability of wet days in the Sahel region under anthropogenic forcing scenarios RCP4.5 and RCP8.5. The decrease in wet days is stronger in the far future and under the RCP8.5 scenario (up to -30%). The study also finds that the probability of consecutive dry days (lasting at least 7 days and 10 days) is expected to increase in the Western Sahel, the Central Sahel, and the Sudanian Area under both scenarios, with stronger increases in the RCP8.5 scenario. In contrast, the decrease is expected over the Guinea Coast, with the changes more important under the RCP4.5. These changes in dry- and wet-spell probabilities are important for water management decisions and risk reduction in the energy and agricultural sectors. The study also highlights the need for decision-makers to implement mitigation and adaptation policies to minimize the adverse effects of climate change.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

The study investigated the usage of open data in public organizations, focusing on the motives, preferences, and governance ideals that determine their quality. The study shed light on how open data platforms are created and improved, as well as their influence on government operations. The primary goal was to understand the motivations behind the usage of open data, evaluate gov-ernance ideals, and examine institutions' efforts to standardize data formats. Hierarchical regres-sion analysis divides variables into core reasons and different preferences, demonstrating a need for "diversification" in order to use open data effectively. Efficiency, accountability, community impact, knowledge, and high-quality service delivery are all emphasized in governance value analysis. The institution's dedication to standardizing open data formats is evidenced by legislative measures and the integration of many technologies. The findings illustrate the institution's dual strategy of em-ploying traditional techniques and new technologies for effective data management. The report suggests increasing data openness and standardization, investing in ongoing training, upgrading alerting and awareness systems, and adopting specific regulations for open data use. Monitoring and feedback techniques are critical for adjusting and refining open data services to satisfy de-velopment needs. This study adds to the scientific knowledge of open data use by highlighting important motives, preferences, and governance ideals. The offered guidelines provide practical insights for public organizations looking to improve their open data platforms by promoting openness, efficiency, and community participation.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

Climate change is a major development challenge to Ethiopia. Unless adaptation measures are widely implemented, climate change can set back development efforts and achievements by years. Recognizing this, the Government of Ethiopia (GoE) and civil society organizations have since recently been making considerable efforts to tackle the climate change problem. This paper documents the experience of CARE International in Ethiopia in facilitating bottom-up approaches to promote community-led disaster risk management and climate change adaptation planning through a participator scenario planning (PSP) methodology. PSP is a coordinated approach which leverages a variety of stakeholders' skills and mandates to explore potential climate change risks and their impacts, and then develop locally relevant and shared adaptation action plans that support livelihoods, social capital and ecosystem resilience. The approach has facilitated timely access to and communication of seasonal climate advisories which in turn is empowering communities to take advantage of opportunities that climate presents, which is a key part of adapting to climate change. The institutionalization of the approach by district and regional disaster prevention and food security coordination offices in the southern pastoral regions of Ethiopia encouraged integration of PSP into community livelihood adaptation and local government development planning, hence continuity of the process. Sustainability is expected to be fully achieved when local government planning processes recognize the importance of and provides resources for the participation of meteorological services and community forecasting experts to help refine plans on a seasonal basis, and for systems for dissemination of advisories. Key words: Climate Change, Disaster Risk Reduction, Adaptation, Pastoralism, Ethiopia,

This bibliographic study addresses key aspects related to fishing, product safety, and climate change in the Adriatic Sea region. The examination of product safety focuses on the assessment of contaminants originating from human activities such as industry, mining, agriculture, and household waste disposal. The contamination of the aquatic environment has emerged as a pressing global concern, extending to the Adriatic subbasin. Aquatic organisms, including fish, are prone to accumulating pollutants directly from polluted water sources and indirectly through the food web. The bio-accumulation of potentially hazardous substances, particularly heavy metals, pesticides, PCBs, PAHs, and antibiotic resistance in aquatic organisms, poses a significant threat to human health. Climate change effects will deplete our seafood supply in terms of quantity and safety owing to negative consequences such as higher levels of pollution, parasites, viruses, infections, acidification, and toxicities such as shellfish poisoning. Global food safety strategies should be developed to reduce greenhouse gas emissions and promote environmentally friendly technology, which indirectly affects seafood quality and microbiological safety, especially for Adriatic Sea, which is part of the Mediterranean Sea, characterized by the most polluted waters in the world.

The importance of bio robotics has been increasing day by day. Researchers are trying to mimic nature in a more creative way so that, the system can easily adopt the complex nature and its environment. Hence, bio robotic gripper plays a role in physical connection between the environment and bio robotics system. While handling the physical world in biorobots gripper, the complexity occurs in feedback system where sensor plays a vital role. Therefore, human centered gripper sensor has a good impact on bio robotics field. But categorical classification and their selection process is not very systematic. This review paper follows PRISMA methodology to summarize the previous works on bio robotics gripper sensor and its selection process.. This paper discusses challenges in soft robotics systems, and the importance of sensing systems to facilitate critical control mechanisms along with their selection considerations. Furthermore, a classification of soft actuation based on gripper has been introduced. Moreover, some unique characteristics for soft robotics sensor are explored namely compliance, flexibility, multifunctionality, sensor nature, surface properties, and material requirements. In addition, a categorization of sensors for soft robotic gripper in terms of modalities has been established ranging from the tactile and force sensor to slippage sensor. Various tactile sensors ranging from piezoelectric sensing to optical sensing are explored as it has utmost importance in soft gripper to effectively address the increasing requirements for intelligence and automation. Finally, taking everything into consideration, a flow diagram has been suggested for selecting sensors specific to soft robotics applications.

Plastic contamination of small dimensions (

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

Social Economy institutions seek to provide answers to social problems, given that they naturally have a socially responsible mission. This study aims to answer the research question: how sustainable practices, namely environmental behaviour, have been adopted by Portuguese Private Social Solidarity Institutions (IPSS) with the purpose of contributing to Sustainable Development? To achieve this objective, qualitative research was carried out in 31 IPSS, which was framed within the scope of the TFA project (Theoretical framework for promotion of accountability in the social economy sector: the IPSS case). Semi-structured interviews were conducted, with a script based on the literature review, from May to July 2019, with those responsible for the management of these entities. A content analysis was conducted, using the NVivo12 Version 12.6.0 software, which enables data to be coded and categorised, reducing any researcher bias. The results indicate that most entities carry out activities of an environmental nature, related to the reuse of materials, the recycling of waste, the sale of materials for recycling, and user awareness. Several entities expressed financial limitations to the implementation of Environmental Management Systems and their accomplishment. However, the objections presented are not impossible to overcome, according to studies presented in other countries.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

The technological revolution has contributed significantly to environmental and social issues worldwide. In higher education institutions, there is a theoretical gap in systematic reviews on the integration of digital transformation into sustainability. This systematic review of the literature aims to address this gap by exploring how digital transformation improves sustainability in higher education institutions, identifying emerging trends and best practices for effective strategies. Using the PRISMA guidelines, the study conducted a comprehensive search in the Scopus database, producing 1,686 publications from 2019 to 2024. The findings reveal a widespread awareness of digital technology integration but highlight a lack of consensus on sustainable integration strategies. Furthermore, the results demonstrate that educational achievements can be enhanced through tools and methodologies that align with the Sustainable Development Goals of the United Nations. The analysis identifies three primary domains: sustainability capabilities enabled by digital transformation, innovative sustainable approaches, and the conceptualisation of sustainability in higher education. The incorporation of digital tools, such as AI chatbots, institutions foster innovation and achieves sustainability objectives, thus transforming teaching and learning approaches. This review contributes significantly to understanding the role of digital transformation in promoting a sustainable and digitally enabled future in higher education.

Ice formation on aircraft surfaces poses significant safety risks, and current detection systems often struggle to provide accurate, real-time predictions. This paper presents the development and comprehensive evaluation of a smart ice control system using a suite of machine learning models. The system utilizes various sensors to detect temperature anomalies and signal potential ice formation. We trained and tested supervised learning models (Logistic Regression, Support Vector Machine, Random Forest), unsupervised learning models (K-means clustering), and neural networks (Multi-Layer Perceptron) to predict and identify ice formation patterns. Experimental results demonstrate that our smart system, driven by machine learning, accurately predicts ice formation in real-time, optimizes de-icing processes, and enhances safety while reducing power consumption. This solution holds the potential for improving ice detection accuracy in aviation and other critical industries requiring robust predictive maintenance.

Despite saltmarshes being considered as nature-based solutions (NbS) towards climate change mitigation, India’s saltmarsh ecosystems are least studied. This study quantifies the seasonal variation in carbon stocks mono-specific saltmarsh species (Porteresia coarctata) and its potential to play an important role in India’s climate change mitigation plans. Seasonal (pre-and post-monsoon) sampling of P. coarctata surface water, biomass and 30 cm sediment core was collected across four locations on the east coast of India to quantify sediment dry bulk density (DBD), organic matter (OM%), organic carbon (Corg%), Corg stocks of sediment and biomass, total carbon (C%) and nitrogen (N%) and stable isotopes of δ13C and δ15N. In general, the sediment DBD, OM and Corg of P. coarctata meadows was higher in post-monsoon and was influenced by salinity and pH changes. Isotope (δ¹³C) modelling of various sediment C sources suggested, particulate organic matter (POM) contribution was highest (0.04-0.79%) followed by P. coarctata (0.01–052%) and other macrophytes across our study locations. The seasonal variation of δ¹³C showed increased contribution of marine derived particulate and dissolved organic matter into P. coarctata meadows in post-monsoon season. Heavier δ¹⁵N values were observed in post-monsoon season suggesting anthropogenic input, that was utilized by P. coarctata to increase its above and below-ground biomass and shoot density. The combined ecosystem (30 cm sediment + biomass) Corg stocks of P. coarctata was 1.7-fold higher in post-monsoon (4021.20± 917 Mg C) compared to pre-monsoon (2297.36 ±647 Mg C) season among the four locations with a sediment Corg contribution >70%. Based on the International Panel for Climate Change Tier II assessment the P. coarctata meadows (443 ha) can help in avoiding the pre and post-monsoon emissions of 8431.34 and 14757.84 Mg CO₂ respectively. The combined price of the total CO₂ equivalent stored in P. coarctata meadows in pre- and post-monsoon is US$ 14.50 and US$ 25.38 million respectively. Further studies quantifying the NbS potential of P. coarctata mono-specific and mixed meadows of India’s coast is needed along with integration of saltmarsh ecosystems into India’s National Action Plan on Climate Change.

The build-up of greenhouse gases (GHGs) is causing warmness in the Earth’s atmosphere, resulting in climate change. The transport sector is one of the active members of GHG emissions and it is imperative to use sustainable transport sources to control climate change. The measure aims to encourage citizens to stop using their private vehicles as their choice of transport and instead opt for joint sustainable mobility during traveling. In this study, a quantitative research method was used and data were collected from a sample of 410 respondents through questionnaire. On the other hand, study also took a simulation-based (N=10000) sample size of private vehicle data. The data were analyzed using structural equation modelling. The results revealed that sustainable transportation, climate change technologies and electric rail vehicles reduce climate change in the ecoregions of China. We conclude that sustainable transportation policies could be formulated and implemented to reduce climate change. In response to the research results, it is recommended that, since climate change is a multi-level governance issue and the outdated pyramidal transport industry models must be shifted to a sustainable transportation system model.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

This study examines the relationship between Gross Domestic Product (GDP) and income inequality in Greece across three key periods: the pre-crisis period (2003-2008), the crisis and memoranda period (2009-2014), and the post-crisis period (2015-2020). Using data from the World Bank Open Data database, the study employs correlation analysis, and linear regression models to analyze how economic changes influence income distribution. The findings reveal that during the pre-crisis period, economic growth was moderately correlated with increasing inequality, although this relationship was not statistically significant, indicating uneven distribution of growth benefits. In the crisis period, a strong and statistically significant negative relationship between GDP and the Gini coefficient was identified, highlighting the sharp rise in inequality as the economy contracted due to austerity measures. In the post-crisis period, the relationship between GDP and inequality weakened, showing a statistically insignificant correlation, suggesting that economic recovery alone did not significantly reduce inequality. The study concludes that economic growth is insufficient to address income inequality without targeted policy interventions, particularly during periods of crisis. These findings underscore the importance of comprehensive social policies to mitigate inequality and suggest areas for future research on the impact of specific interventions on income distribution.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

Water scarcity, particularly in arid and semi-arid regions, poses a significant challenge to crop production, with drought being a prevalent factor limiting grain production globally. Enhancing agricultural water use efficiency is crucial for managing water resources effectively in these areas. Water resource management involves planning, developing, distributing, and optimizing the use of water resources. Water use efficiency management is also essential for crop growth in arid regions. Various agronomic and irrigation strategies can improve crop water use efficiency and drought tolerance. The primary goal of these strategies is to maximize irrigation efficiencies by applying the precise amount of water needed to restore soil moisture to the desired level. These sustainable practices not only reduce the cost of water and labor for farmers through reduced irrigation but also optimize the use of soil moisture storage. This review paper explores practical techniques to improve water use efficiency, highlighting the role of nutrients in enhancing water use efficiency in crop plants.

The monitoring of coastal waters using satellite data, from sensors including Sentinel-3 OLCI, has become a vital tool in the management of these water environments; especially when it comes to improving our understanding of the effects of climate change on these regions. In this study, Level-2 water products derived from different OLCI Sentinel-3 processors were validated against a comprehensive in situ dataset from the NW Baltic Sea proper region. The products validated were those of the regionally adapted Case-2 Regional Coast Colour (C2RCC) OLCI processor (v1.0 and v2.1), as well as the latest standard Level-2 OLCI case 2 (Neural Network) products from Sentinel-3’s processing baseline: Baseline Collection 003 (BC003), including “CHL_NN”, “TSM_NN”, and “ADG443_NN”. Furthermore, the effect of the current EUMETSAT system vicarious calibration (SVC) on the Level-2 water products was also validated. Results showed that the system vicarious calibration (SVC) reduces the reliability of the Level-2 OLCI products. For example, the application of these SVC gains to the OLCI data for the regionally adapted v2.1 C2RCC products resulted in RMSD increases of 36% for “conc_tsm”; 118% for “conc_chl”; 33% for “iop_agelb”; 50% for “iop_adg”; and 10% for “kd_z90max” using a ±3h validation window. The findings indicate that the current EUMETSAT SVC gains should be applied and interpreted with caution in the region of study at present. A key outcome of the paper recommends the development of a regionally specific SVC against AERONET-OC data for the region.

Aerosol-cloud interactions play a crucial role in shaping Earth’s climate and hydrological 1 cycle. Observing these interactions with high precision and accuracy is of the utmost importance 2 for improving climate models and predicting Earth’s climate. Over the past few decades, lidar 3 techniques have emerged as powerful tools for investigating aerosol-cloud interactions due to their 4 ability to provide detailed vertical profiles of aerosol particles and clouds with high spatial and 5 temporal resolutions. This review paper provides an overview of recent advancements in the study 6 of aerosol-cloud interactions using lidar techniques. The paper begins with a description of the 7 different cloud microphysical processes that are affected by the presence of the aerosol, and with 8 an outline of lidar remote sensing application in characterizing aerosol particles and clouds. The 9 subsequent sections delve into the key findings and insights gained from lidar-based studies of 10 aerosol-cloud interactions. This includes investigations into the role of aerosol particles in cloud 11 formation, evolution, and microphysical properties. Finally, the review concludes with an outlook 12 on future research. By reporting the latest findings and methodologies, this review aims to provide 13 valuable insights for researchers engaged in climate science and atmospheric research.

Addressing escalating energy demands and greenhouse gas emissions in the oil and gas industry has driven extensive efforts in carbon capture and utilization (CCU), focusing on power plants and industrial facilities. Utilizing CO2 as a primary feedstock for industrial fuels and petrochemical materials offers a favorable alternative to sequestration, with byproducts substituting traditional chemical feedstocks. This comprehensive review explores the current landscape of CO2 capture technologies, examining opportunities, economic viability, and efficiency challenges. It provides a detailed analysis of various CO2 utilization methods and the combined process of capture and utilization. The review highlights primary obstacles in planning, production, and widespread implementation, emphasizing the need for strategic integration of materials research, process performance, and cost-effectiveness to advance new technologies.

Since the 1960s, the countries of sub-Saharan Africa have been affected by an urban crisis due to the demographic explosion in cities and the resulting land pressures. These have resulted in the proliferation of spontaneous housing areas which question the future of urban vegetation and its degree of inclusion in city planning. To analyze the state of knowledge on the research already carried out on the development of urban landscape, particularly in sub-Saharan Africa, a literature review on urban forestry covering the period 1998-2022 was carried out in order to better orient future research works for a greater consideration to urban forestry and their contributions in combating the adverse effects of climate change. Out of a set of 110 scientific papers selected, 50 were considered relevant because of their direct link with urban forestry. From the analysis of this papers, a classification of the articles according to 05 themes was carried out. These are: management of green spaces in urban areas, functions of trees in an urban environment, development of urban forestry, characterization of urban tree flora and financing of urban forestry. Thus, “function of trees in an urban environment and the characterization of urban tree flora” are the most addressed respectively at 42% and 28%. “Financing urban forestry” is practically not addressed (2%). The analysis of the 50 selected articles reveals a significant geographic concentration of urban forestry research. Countries like South Africa, Kenya, and Ghana are more represented in the literature, while vast regions in Central and Western Africa (e.g., Democratic Republic of Congo, Chad, and Niger) have minimal or no documented research on urban forestry. Future research should address these underrepresented themes, as they are crucial for the long-term sustainability of urban forestry projects. Particularly, research on financing mechanisms is essential to unlock sustainable funding sources for urban forestry, a critical barrier to its expansion.

Increased wildfire activity is the most significant natural disturbance affecting forest ecosystems, with a strong impact on their natural regeneration. This study presents a comprehensive analysis of post-fire forest recovery using Landsat time series data from 2000 to 2023 in the Middle Volga region of the Russian Federation. The analyses utilised the LandTrendr algorithm in Google Earth Engine (GEE) cloud computing platform to examine Normalized Burn Ratio (NBR) spectral metrics and quantify the forest recovery at low, moderate, and high burn severity (BS) levels. To assess the spatio-temporal trends of the recovery, the Mann–Kendall statistical test and Theil–Sen’s slope estimator was applied. The results suggested that the post-fire spectral recovery is significantly influenced by the degree of the BS on affected areas. The higher the class of BS, the faster and more extensive the reforestation of the area occurs. About 91% (40,446 ha) of the first 5-year forest recovery after the wildfire belong to the BS classes of moderate and high severity. A regression model showed that land surface temperature (LST) was more significant to post-fire recovery than the variability in precipitation (Pr), explaining about 65% of the variance in post-fire recovery. This study provides new insights into the post-fire forest recovery dynamics and scientific bases for the cost-effective management strategies under changing climate conditions.

The paper is devoted to fundamental issues concerning to the ideology of the future sustainable development. Its implementation has available in the first place basing on the recognized framework concept of sustainable development (SD). At the same time, this concept requires serious improvement. As follows from the argumentation, a realistic design of institutional changes in connection with resource and organizational/behavioral changes needed for SD is called for to realize in the line of overall social system transformation. Its adequate understanding presupposes an exhaustive study of interconnected transformations in the main social fields as system processes taking into account the influence of relatively exogenous factors (technological, demographic and climate changes).According to the author, the transition to global sustainable social transformation is achievable. Main attention focuses on a number of possible fundamental shifts, the synergetic implementation of which will make such a transition possible.Proceeding from the arguments, the sustainable reproduction of the economy of a mature post-industrial type, including the green sectors, implies its stable and quiet growth, although the rapid growth of individual markets, especially innovative ones, may take place. The main findings also include the substantiation in favor of the choice of the national middle way model as the most appropriate for the corresponding sustainable system transformation of society.

Crawling robots are the focus of intelligent inspection research, and the main feature of this type of robot is the flexibility of in-plane attitude adjustment. The crawling robot HIT_Spibot is a new type of steam generator heat transfer tube inspection robot with a unique mobility capability different from traditional quadrupedal robots. This paper introduces a hierachical motion planning approach for HIT_Spibot, aiming to achieve efficient and agile maneuverability. The proposed method integrates three distinct planners to handle complex motion tasks: a nonlinear optimization-based base motion planner, a TOPSIS-based base orientation planner, and a Mask-D3QN (MD3QN) algorithm-based gait motion planner. Initially, the robot's base and foot workspace are delineated through envelope analysis, followed by trajectory computation using Larangian methods. Subsequently, the TOPSIS algorithm is employed to establish an evaluation framework conducive to foundational turning planning. Finally, the MD3QN algorithm trains foot points to facilitate robot movement along predefined paths. Experimental results demonstrate the method's adaptability across diverse tube structures, showcasing robust performance even in environments with random obstacles. Compared to the D3QN algorithm, MD3QN achieves a 100% success rate, enhances average overall scores by 6.27%, reduces average stride lengths by 39.04%, and attains a stability rate of 58.02%. These results not only validate the effectiveness and practicality of the method but also showcase the significant potential of HIT_Spibot in the field of industrial inspection.

The COVID-19 pandemic has triggered seismic shifts in how we work, and organizations behave. It has caused many organizations to transition from an office-centric culture to more flexible ways of working. This shift is necessitated by health conditions and the need for controls. It is also driven by the assumption that remote work or working from home offer a certain assurance of safety for employees against the threat of infection in highly vulnerable office conditions. The shift to remote work has so far been mainly experimental as most businesses continue to learn about what works and what doesn’t. There is also the assumption that all that matters for the efficient operability of a remote work regime is the availability and effectiveness of computing technologies and internet connectivity. Thus, once those supplies are in place remote work is expected to be fully functional and without problems. As learning continues about what works and what doesn’t, it has also become increasingly clear that beyond the threat of covid-19 and the relative safety that individual homes may offer, there are other vulnerabilities which are ignored or underestimated in the process. In most instances, the home environment of the employee, the conditions under which employees operate from home and the health and safety such environments provide (or not) are either ignored or underestimated in discussions around remote work practices. This paper highlights remote work as an emergent practice while exploring associated, but ignored, health and safety issues in employee homes.

.Maize cultivation in Thailand faces challenges owing to climate change and soil organic carbon (SOC) loss. This highlights the importance of comparing maize soil with paddy soil in terms of the role of dissolved organic carbon (DOC) and nutrient availability, as they influence SOC content. Soil samples from Chiang Mai province, primarily Fluvisol, were collected for the cultivation of paddy rice and maize, analysed for carbon fractions and chemical properties, and categorised into layers. Comparative analysis revealed that maize soils had lower levels of labile carbon components and organic carbon than paddy soils (P

Floods, recognized for their erratic behavior and devastating effects, are a significant threat as a natural disaster. In Brunei Darussalam, the impact of climate change is becoming increasingly evident through higher temperatures and an expected increase in annual rainfall (5.0mm per year from 2021 to 2050), highlighting the critical need for updated flood risk management techniques. In line with the climate resilience and adaptation objectives of WAWASAN 2035, this paper introduces an innovative approach—a cutting-edge flood risk management framework that utilizes the capabilities of big data analytics, sophisticated machine learning algorithms, and smart Internet of Things (IoT) sensors. Traditional methods, which rely on numerical and physical data modeling, often do not provide precise short-term flood forecasts. Our suggested framework uses machine learning to analyze real-time flood forecasting, sensor data and enhance warning systems, addressing the shortcomings of traditional approaches. The key advantage of this approach is its potential to drastically decrease flood-related damages, protect lives, and boost infrastructure resilience. This proposal is not only in aligns with Brunei's vision for a safe and climate-adaptable future but also marks a significant step forward in adopting innovative and sustainable flood risk management solutions amidst an evolving climate.

Beliefs that maintain patriarchal principles may affect individuals’ willingness to avoid conflicts in their intimate partner relationships and eventually are likely to affect chances of intimate partner economic violence. Nonetheless, research has yet to fully explore these associations. This study used a sample of 321 adults in the ultra-Orthodox Jewish community—a patriarchal and traditional culture—to examine associations in beliefs supporting patriarchal principles at the micro (gendered domestic roles), meso, and macro ( institutional power of men and inherent inferiority of women) levels; conflict avoidance and economic violence; and sex differences in these factors. Descriptive statistics were used to explore gender differences in research variables, and path analysis examined the correlations between research variables for men and women. Beliefs in patriarchal ideologies were moderate at all levels, although slightly higher among men. Men tended to avoid conflict with their intimate partner significantly more than women did. Beliefs in support of patriarchal ideologies predicted conflict avoidance, especially among women. Finally, in opposition to prior research findings, this study revealed nonsignificant sex differences in the prevalence of economic violence victimization. These findings, however, do not suggest that economic violence victimization is not rooted in sex issues. We discuss the findings and the meanings assigned to conflict avoidance by men and women while considering gender disparities of power and control. We suggest that the contribution of men’s tendency to avoid conflict likely moderated their chances to perpetrate economic violence.

This study explores the current landscape of social value (SV) research in the construction industry, analyzing global trends and identifying future research directions. Using bibliometric analysis, research published in Elsevier Scopus database from 2013 to 2023 was extracted using the keywords "social value" AND "construction industry." Results indicate a focus on social value indicators, socioeconomic impacts, project management, innovative practices, and cross-sector collaborations. The study also reveals a lack of attention to SV in African countries' construction sectors. By highlighting research areas and identifying gaps, this study contributes to academic literature, suggesting the need for guidelines, particularly in developing countries, and advocating for further research on SV in the built environment and strategies for global social value creation.

The Kampar Peninsula, a significant peatland region in Riau, Indonesia, is vital for its carbon re-serves and biodiversity, including the Sumatran tiger. Covering approximately 735,091 hectares, it comprises critical peat domes essential for hydrological balance. This research investigates land use changes from 1990-2020 using the Normalized Difference Fraction Index (NDFI) to map disturb-ances and land cover changes. Additionally, interviews and regulatory analysis were conducted to examine the historical drivers of land use change in the Kampar Peninsula. In 2020, natural forests covered 433,395.20 hectares (59.9% of the total area), industrial pulpwood plantations (primarily acacia) covered 27.3%, oil palm plantations accounted for 10.4%, infrastructure occupied 2.4%, and water bodies made up 0.9%. Key drivers of land use change include the construction of access roads by oil companies since 1975 and government policies during the New Order period (1980s-1998) promoting forest exploitation and transmigration programs. These activities have significantly transformed the Kampar Peninsula's land cover, highlighting the need for sustainable management and conservation efforts.

Heavy metals are dangerous contaminants constituting a threat to human health because they persist in soils and are easily transferred into the food chain, causing damages to human health. Among heavy metals, nickel appears to be one of the most dangerous responsible for different disorders. Public health protection requires nickel detection in environment and food chains; a simple, rapid and sensitive method to detect nickel contamination is represented by biosensors. In this paper we report the setup of a whole-cell based system, in which protoplasts, obtained from Nicotiana tabacum leaves, were used as transducers to detect the presence of heavy metal ions and, in particular, nickel ions. Protoplasts were genetically modified with a plasmid containing the GFP reporter gene under the promoter region of a sunflower small HSP gene control. By this device the presence of heavy metal ions was detected. Thus, the possibility to use this whole-cell system as a novel tool to detect the presence of nickel ions in food matrices was assessed.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

Biodiversity loss and nature degradation are pressing issues with huge impacts on our society and economy. Businesses, investors, and regulators focus on corporate efforts to support biodiversity and nature positive actions. This review provides a comprehensive overview about the importance of biodiversity in businesses, the materiality of biodiversity and the role of mandatory and non-mandatory regulations on corporate environmental reporting and sustainability disclosure frameworks. The review also discusses descriptive information on the evolution of sustainability frameworks with a comparison of most prominent sustainability frameworks with a key focus on the materiality approach and biodiversity-related disclosure recommendations. Further, we provide suggestions for more holistic approaches to improve the future sustainability frameworks focusing on the biodiversity impact while showing the necessity of more focus on the decision-making paradigm. Further research on measuring biodiversity impact and innovative trends in sustainability reporting are required to better reflect nature-positive outcomes in corporate sector businesses.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

In order to achieve global climate goals, it is necessary to estimate greenhouse gases (GHG) fluxes from ecosystems. To obtain a comprehensive assessment of CO2, СН4, N2O natural fluxes for the Russian Federation we used the "bottom-up" method according to [1]. We updated estimates for forest ecosystems based on State Forest Inventory data and satellite monitoring of forest disturbances. For grassland ecosystems, it was based on the correct distribution of areas between steppe and non-steppe zones. The estimated net uptake of natural ecosystems of Russia was 1.1 ± 1.8 billion tons of CO2-eq./year. The study shows that if only CO2 is taken into account, the net absorption of terrestrial ecosystems in Russia corresponds to more than -2.5 billion tons of CO2 (35% of forests’ contribution). However, given the emissions of non-CO2 GHGs, total net absorption in Russia’s natural ecosystems is reduced to about -1 billion tons of CO2-eq (with the forests’ contribution increasing to 80%). With regard to anthropogenic fluxes, the overall balance of GHGs in Russia corresponds to net-emissions of 1 billion tons of CO2-eq/year into the atmosphere. To improve reporting under the Paris Agreement, countries should aim to include only anthropogenic ("manageable") GHG fluxes on managed land.

Background: The workplace burnout syndrome is often associated with particular aspects of certain job positions, especially those which entail working with people with special needs. The burnout syndrome in healthcare jobs is a serious problem which has grown into an epidemic among healthcare workers and associates. Objectives: The aim of this research is to assess the presence of stress and burnout syndrome at work with healthcare workers, expert workers, professional associates and associates in social service institutions in Belgrade. Material and Methods: This research has been conducted in the form of a cross-sectional study of a representative sample in social institutions in Belgrade. It has been conducted from March to the end of June of 2023. The sample of the study had 491 participants. The questionnaires used were a structured instrument with social-demographic and social-economic characteristics, workplace characteristics, life style characteristics, and the following questionnaires: DASS-21, Copenhagen, Brief Resilience Scale, and Brief Resilient Coping Scale. Results: The end results indicate the following to be significant risk factors for the occurrence of workplace burnout syndrome: overtime (OR=2.62; CI=1.50-4.56), BRS average score (OR=0.28; CI=0.17-0.44), DASS21 D heightened depression (OR=2.09; CI=1.1-4.04), DASS21 A heightened anxiety (OR=2.38; CI=1.34-4.21), DASS21 S heightened stress (OR=2.08; CI=1.11-3.89). The only protective risk factor which stood out was the self-assessment of health levels (OR=0.60; CI=0.42-0.85). Conclusion: Overtime is a significant predictor of workplace burnout. Apart from it, other significant predictors of workplace burnout were heightened depression, anxiety, and stress levels.

Currently, one of the main challenges is the mitigation of the effects of climate change on the agricultural sector. Conventional agriculture, with the intensive use of herbicides and pesticides to control weeds and pests, and the improper use of mineral fertilizers, contributes to climate change by causing increased greenhouse gases and groundwater pollution. Therefore, more innovative technologies must be used to overcome these problems. One possible solution is nanotechnology, which has the potential to revolutionize the conventional agricultural system. Active nanoparticles can be used both as a direct source of micronutrients and as a delivery platform for bioactive agrochemicals to improve crop growth, yield and quality. The use of nanoparticle formulations, including nanopesticides, nanoherbicides, nano-fertilizers and nano-emulsions, has been extensively studied to improve crop health and shelf life of agricultural products. Comprehensive knowledge of the interactions between plants and nanoparticles opens up new opportunities to improve cropping practices through the enhancement of properties such as disease resistance, crop yield, and nutrient use. The main objective of this review is to analyze the main effects of climate change on conventional agricultural practices, such as the use of pesticides, herbicides and fertilizers. It also focuses on how the introduction of nanoparticles into conventional practices can improve the efficiency of chemical pest control and crop nutrition. Finally, this review examines in depth the last 10 years (2014-2024) of scientific literature regarding the use of nanoparticles in agriculture to mitigate the effects of climate change.

The West Pomeranian Anti-Crisis Package was an effective tool of the Voivodeship Executive Board of West Pomeranian self-government, which was used to combat and counteract and counteract the social and economic effects of the COVID-19 pandemic. The Anti-Crisis Package was prepared with a view to undertaking systemic, but also point-based measures in order to save and protect regional health care, entrepreneurs, the labour market, but also to use the existing social capital of non-governmental organizations involved in measures reducing the effects of the COVID-19 pandemic. The West Pomeranian Anti-Crisis Package, as evidenced not only by the financial outlays incurred, but also by the outcome of implementing measures achieved in 2020 and their continuation in 2021.

Rice yield underperformance coupled with production instability in Odisha state of India is primarily due to low irrigation potential, the spatiotemporal disparity in rainfall pattern and relentless confrontation with biotic and abiotic stresses. System of Rice Intensification (SRI) was introduced in the state with the promises of higher production horizon. However, the present scenario of patchy adoption pattern has necessitated comprehensive study on dynamics and determinants of adoption of SRI. We found that, 57 percent farmers continued SRI, 28 percent discontinued and rest were practicing conventional rice farming. The focused group discussion among the farmers helped us to triangulate the determinants of SRI adoption.The increased SRI area allocation was observed at the expense of reduced number of adopting farmers. Economic scarcity of skilled labour, difficulties in transplantation and mechanical weeding, low irrigation potential and poor on-farm water management were major constraints in SRI practice. Farmers’ compliance in following different resilient SRI components that also varied spatiotemporally has resulted in realized incremental yield. SRI was proved to be resilient to severe drought during 2015-16 and yielded 27 percentage higher than conventional one with considerable decline in hazardous chemicals usage. Farmers’ decision on SRI adoption/discontinuation was analysed using probit regression analysis. The results indicated that, active social involvements of NGOs, on-farm training and demonstrations, and realized incremental rice income influenced SRI adoption. On the other hand, SRI area expansion hindered mainly because of infeasible land topography, area saturation and lack of farmers’ interest. The sustainability index was developed to analyse SRI’s performance to other conventional methods at farm level. Comparatively, SRI adopters benefitted in terms of incremental net return by enhancing ecological balance and sustained productivity of soil, use of eco-friendly and own farm inputs. Nonetheless, higher women labour displacement observed under SRI can be curtailed by providing training to young farm women.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

In 2020, the Covid-19 outbreak led many countries across the globe to introduce lockdowns (LDs) that effectively caused most anthropic activities to either stop completely or be significantly reduced. In Europe, Italy played a pioneeristic role via the early introduction of a strict nationwide LD on March 9^th. This study is aimed at evaluating, using both chemical and meteorological data, the environmental response to that occurrence as observed by the Lamezia Terme (LMT) GAW/WMO station in Calabria, Southern Italy. The first 2020 lockdown has therefore been used as a “proving ground” to assess CO, CO₂, CH₄, BC, and NO_x concentrations in a rather unique context by exploiting the location of LMT in the context of the Mediterranean Basin. In fact, its location on the Tyrrhenian coast of Calabria and local wind circulation both lead to daily cycles where western-seaside winds depleted in anthropogenic pollutants can be easily differentiated from northeastern-continental winds, enriched in anthropogenic outputs. In addition to that, the first Italian LD occurred during the seasonal transition from Winter to Spring and, consequently, Summer, thus providing new insights on emission outputs correlated with seasons. Findings have clearly indicated BC and, in particular, CO as strongly correlated with average daily temperatures, and possibly domestic heating. CO₂’s reduction during the lockdown and consequent increase in the post-lockdown period, combined with wind data, has allowed to constrain local source of emissions located northeast from LMT. NO_x reductions during specific circumstances are consistent with hypotheses from previous research which linked them to rush hour traffic and other forms of transportation emissions. CH₄’s stable patterns are consistent with livestock, landfills, and other sources assumed to be nearly constant during LD periods.

Driven by the growing interest of the scientific community and the proliferation of research in this field, cranial implants have seen significant advancements in recent years regarding design techniques, structural optimisation, appropriate material selection and fixation system method. Custom implants not only enhance aesthetics and functionality but are also crucial for achieving proper biological integration and optimal blood irrigation, critical aspects in bone regeneration and tissue health. This research aims to optimize the properties of implants designed from triply periodic minimal surface structures. The gyroid architecture is employed for its balance between mechanical and biological properties. Experimental samples were designed varying three parameters of the surface model: cell size, isovalue and shape factor. Computational simulation tools were used for determining the relationship between those parameters and the response variables: the surface area, permeability, porosity and Young modulus. These tools include computer aided design, finite element method and computational fluid dynamics. With the simulated values, the corresponding regression models were fitted. Using the NSGA-II, a multi-objective optimisation was carried out, finding the Pareto set which includes surface area and permeability as targets, and fulfil the constraints related with the porosity and Young modulus. From these non-dominated solutions, the most convenient for a given application was chosen, and an optimal implant was designed, from a patient computed tomography scan. An implant prototype was additively manufactured for validating the proposed approach.

Despite the known benefits of precision agriculture, the adoption is challenging due to the cost of investment and the farm sizes. Therefore, profitability is an important aspect to consider. This study aimed to evaluate the net returns, profitability, and investment efficiencies of PA by different economic farm sizes. The study was based on data retrieved from FADN and Eurostat. The study examined four countries (Poland, Germany, France, and Romania) under field crop farming using an investment cost of €35 941 - €71 883, and a 20% and 15% reduction in the cost of crop protection and fertilizer usage respectively without compromising productivity. There is a positive relationship between the adoption of PA and farm returns for larger-scale farms. The result of the profitability and analysis of investment efficiency using NPV showed a positive value for economic farm sizes of €100 000 and above. Hence, it is not economically advisable that all farmers use PA technologies with the hope that they will be profitable but with public support (subsidies) more farms will be able to use PA and be profitable. Also, an opportunity to meet the goal of the European Union Green Deal of minimizing emissions that cause climate change.

The aim of this work was to classify the business incubators in Spain according to the four phases of the startup’s incubation process. Considering that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the business incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis has been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors. Finally, the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3, named activity monitoring and control, was related to phase 3 or basic incubation variables. Cluster analysis facilitates the grouping of business incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small sized business incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factors 1 and 2. Factor 3, although positive, it is susceptible to improvement. They are the largest group of business incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

The use of educational robotics has become increasingly popular in STEM education, offering motivating and hands-on learning experiences. This paper explores the potential of educational robotics for teaching plane curves at the university level. Specifically, it investigates the development and implementation of a LEGO SPIKE Prime robot designed to draw various central trochoids, including epicycloids and hypocycloids. The robot’s construction and programming are described, emphasizing the relationship between the robot’s physical movements and the mathematical equations of the curves it produces. The study also examines the integration of dynamic geometry software, which allows for visualization of the curves and verification of the robot’s accuracy. The paper concludes that educational robotics can serve as a valuable tool for enhancing both theoretical and practical understanding of mathematical and engineering concepts, offering a more engaging and interactive approach to learning.

In Africa, the urban population and informal settlements are increasing, resulting in additional public health and environmental risks and challenges related to the need of basic and sustainable infrastructures and services. In Maputo, the capital of Mozambique, at least 80% of the city is composed of informal settlements, and although some areas are regularized and have approved urbanization plans, the municipality has major deficiencies in meeting current demands in terms of basic infrastructures, such as water supply, sewerage, solid wastes, energy, roads and communications. Most of the peri-urban areas is occupied with small but overcrowding houses, mostly self-built, served by unpaved roads, and with access limitations. The water network is almost non-existent, and the same occurs for stormwater drainage, sanitation, waste collection and public illumination. Despite the improvements made in the last few years, some households still do not have safe sanitation, and in some neighborhoods, open defecation still prevails. In this study, the authors try to understand and explore the interdependences among the infrastructures of the different sectors and how they may jointly contribute for adequate services and a better life of the urban poor, and how to identify the combination of infrastructures to be implemented at short term in face of the limited budgets for investments.

A multimodal detection system with complementary capabilities for efficient detection was developed for impurity detection. The system consisted of a visible light camera, a multispectral camera, image correction and registration algorithms. It can obtain spectral feature and color feature at the same time, and has higher spatial resolution than a single spectral camera. This system was applied to detect impurities in Pu ’er tea to verify its high efficiency. The spectral and color features of each pixel in the images of Pu ’er tea were obtained by this system and used for pixel classification. The experimental results show that the accuracy of Support Vector Machine (SVM) model based on combined features is 93%, which is 7% higher than that based on only spectral features. By applying median filtering algorithm and contour detection algorithm to the label matrix extracted from pixel-classified images, 8 impurities except hair were detected successfully. Moreover, taking advantage of the high resolution of visible light camera, small impurities can be clearly imaged. By comparing the segmented color image with the pixel-classified image, small impurities such as hair could be detected successfully. Finally, it is proved that the system can obtain multiple images to allow a more detailed and comprehensive understanding of the detected items, and has excellent ability to detect small impurities.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Foods are complex products consisting of various ingredients of diverse origins. Along the food supply chains, food products are prone to spoilage and safety issues, which could give rise to different health-related concerns and outcomes. Furthermore, the existing highly centralised food systems generate substantial greenhouse gas emissions and food waste. In order to strengthen the sustainable decentralised "farm-to-fork" food chains, a mindset shift supported by relevant education and policy initiatives is highly required. The ERASMUS+ KA220 project SafeFood4EU was conceived with a crucial mission- to develop an interdisciplinary and innovative toolbox of higher education and lifelong learning courses that reflect various aspects of sustainable agri-food systems. The thematic areas discussed within the SafeFood4EU project have covered food safety and supply chain management, sustainable food systems and design, food production and quality of raw materials, food authenticity and analysis, and digital and soft skills. The main objectives have been to develop a distinctive content package and make it available to the students via an e-learning management system. The project's results, aimed at creating a pool of young and capable experts, can significantly impact future food security, thereby increasing awareness about the future challenges regarding food systems transition, dietary shift and the next generation's food security.

The analysis of chemical warfare agents and their degradation products has become increasingly important for public and military safety in recent years. In the article, we drew attention to the possibilities of the HPLC-ICP-MS analytical technique, which has been relatively rarely used for identifying and quantitatively analyzing highly toxic and hazardous substances in environmental samples. This technique enables the identification and determination of minimal amounts (ppt range) of chemicals in various matrices. This fact is important for the analysis of chemical warfare agents and other highly harmful compounds, even small amounts of which can have serious consequences for living organisms. The article critically analyzes the results of scientific research on the identification and quantitative analysis of extremely toxic organophosphorus, organosulfur and organoarsenic substances, their derivatives and degradation products using high-performance liquid chromatography (HPLC) coupled with inductively coupled plasma mass spectrometry (ICP-MS).

Oedaleus decorus asiaticus, Calliptamus abbreviatus, Angaracris rhodopa, and Myrmeleotettix palpalis are the main grasshoppers that harm the natural grassland in the Hexi Corridor. In this study, the MaxEnt model was employed to identify the key environmental factors affecting the distribution of the four grasshoppers habitats and to assess their distribution under current and future climate change conditions. The aim was to provide a basis for grasshopper monitoring, prediction, and precise control. In this study, 61 occurrences of O. decorus asiaticus, 68 occurrences of A. rhodopa, 58 occurrences of C. abbreviatus, and 92 occurrences of M. palpalis were recorded by GPS, and the distribution of suitable habitats for O. decorus asiaticus, C. abbreviatus, A. rhodopa, and M. palpalis were predicted under current and future climatic scenarios using a MaxEnt model. The average AUC and TSS values of the four grasshoppers were greater than 0.9, and the simulation results were excellent and highly reliable. The mean annual precipitation was the main factor limiting the current range of suitable areas for these four species. Under the current climate, O. asiaticus, C. abbreviatus, and A. rhodopa were mainly distributed in the central and eastern parts of the Hexi Corridor, and M. palpalis was distributed throughout the Hexi Corridor, with a potential distribution area of 1.44×104, 1.43×104, 1.29×104, and 2.12×104 km2, accounting for 15.3, 15.2, 13.7, and 22.5% of the total area of the grasslands in the Hexi Corridor, respectively. The highly suitable areas of O. asiaticus, C. abbreviatus, and A. rhodopa were mainly distributed in the east-central part of Zhangye City, the western part of Wuwei City, and the western and southern part of Jinchang City, with areas of 0.35×104, 0.29×104, and 0.20×104 km2, accounting for 3.7, 3, and 2.2% of the grassland area, respectively. The high habitat of M. palpalis was mainly distributed in the southeast of Jiuquan City, the west, middle, and east of Zhangye City, the west of Wuwei City, and the west and south of Jinchang City, with an area of 0.32×104 km2, accounting for 3.4% of the grassland area. In the 2030s, the range of O. asiaticus, C. abbreviatus, A. rhodopa, and M. palpalis was predicted to decrease.

In terahertz communication systems, lens antennas used in transceivers are basically plano-convex dielectric lenses. As the aperture increases and the focal length decreases, the thickness and mass of the plano-convex lens increase rapidly. Through theory and simulation, we designed a Fresnel lens suitable for the terahertz band to meet the requirements of large aperture and short focal length, and simulated the performance, advantages and disadvantages of the terahertz Fresnel lens. A 300GHz terahertz wireless communication system was built to verify the gain effect of the Fresnel lens antenna. The experimental results show that the Fresnel lens can amplify the signal in the terahertz band. The theoretical gain of a 30 cm Fresnel lens is 48.83dB, while the actual measured gain is approximately 45dB.

This paper undertakes a comprehensive review to underscore the central role of sustainability in the evaluation and innovation of jet grouting technologies. It meticulously traces the evolution of evaluation methodologies, emphasizing the imperative of sustainable practices throughout history. Traditional evaluation paradigms are examined alongside contemporary trends, with a particular focus on sustainability metrics and visualization techniques. Through an examination of innovative jet grouting technologies, this paper illustrates how sustainability principles have driven advancements aimed at improving the efficiency and environmental impact of jet grouting methods. Central to this review is an assessment of sustainability across multiple dimensions, including method applicability, installation and operational compatibility, and the performance of the resulting jet grouted piles. By emphasizing sustainability considerations, the paper highlights the intrinsic link between environmental integrity and technological innovation in the field of jet grouting. In addition, it discusses analytical evaluation methods designed to proactively address sustainability concerns prior to construction, thereby promoting a more environmentally responsible approach. Finally, this paper presents a pioneering evaluation framework that integrates real-time monitoring and visualization tools, allowing stakeholders to track sustainability milestones throughout the construction process. By emphasizing sustainability as a guiding principle, this review advocates for a paradigm shift toward more ecologically sound and resilient jet grouting practices.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Due to its high short-term global warming potential (GWP) compared to carbon dioxide, methane (CH₄) is a considerable agent of climate change. This research is aimed at analyzing data on methane gathered at the GAW (Global Atmosphere Watch) station of Lamezia Terme (Calabria, Southern Italy) spanning seven years of continuous measurements (2016-2022) and integrating the results with key meteorological data. Compared to previous studies on detected methane mole fractions at the same station, daily-to-yearly patterns have become more prominent thanks to the analysis of a much larger data set. Overall, the yearly increase of methane at the Lamezia Terme station is in general agreement with global measurements by NOAA, though local peaks are present, and an increase linked to Covid-19 is identified. Seasonal changes and trends have proved to be fully cyclic, with the daily cycles being largely driven by local wind circulation patterns and synoptic features. Outbreak events have been statistically evaluated depending on their weekday of occurrence to test possible correlations with anthropic activities. A cross analysis between methane peaks and specific wind directions has also proved that local sources may be deemed responsible for the highest mole fractions.

(1) Background: A simple approach to map irrigated landcover has been introduced by using measures derived from optical spectral range as an alternative to thermal range. It has been demonstrated that substituting surface temperature (Ts, ‘thermal approach’) with SWIR transformed reflectance (STR, ‘optical approach’) to detect surface moisture is feasible with comparable results. (2) Methods: Using an iterative thresholding procedure to minimize within-class variance, the bilevel segmentation of variables derived from Landsat-8 representing surface moisture and vegetation cover was achieved for the 2020-21 summer for a key irrigation district in Australia. (3) Results: The results of irrigated landcover by optical approach found to be comparable with those by thermal approach. The classification accuracy was assessed using water delivery records at farm level. Though the overall accuracy is high in both cases, the optical approach (97.6%) performed slightly better than the thermal approach (93.9%). (4) Conclusions: The feasibility of using STR to map irrigated landcover has been confirmed by a high-level overall accuracy assessment. This has broader implications in terms of irrigated landcover assessment, as the use of satellite imagery in these applications may not necessarily be limited to microwave or thermal sensors.

German noise action plans aim to reduce negative health outcomes from noise exposure and identify quiet areas free of noise pollution. Quiet area identification in German noise action plans is based primarily on noise mapping and spatial analysis and not empirical or qualitative data about acoustic environments, thus leaving a gap in the understanding of the quality of formally recognized quiet areas in noise action plans. This work presents a comparative empirical case study in Dortmund, Germany, with the aim to describe the diurnal dB(A) and biophonic properties of quiet areas versus noise 'hot spots'. Sound observations were collected (n=282,764) in five different natural or recreational land use patch types larger than four acres within 33 proposed quiet areas in Dortmund (n=70) and 23 noise hot spots between April 27^th, 2022 and March 2^nd, 2023. We find that quiet areas are on average more than 20 dB(A) quieter than noise hot spots almost every hour of the day. Forests, managed tree stands, cemeteries, and agriculture diel patterns are dominated by dawn dusk chorus in spring and summer, whereas sport and recreation as well as noise hot spots are dominated by traffic and human noise. A novel composite biophony mapping procedure is presented that finds distinct temporal distribution of biophony in forested and agriculture peri-urban locations positively associated with patch size, distance away from LDEN > 55, proximity to water, and the number of vegetation layers in the plant community. Anthrophony distribution dominates urban land uses in all hours of the day, but expands during day and evening and contracts at night and in dusk hours. The procedures presented here illustrate how qualitative information regarding quiet areas can be integrated into German noise action planning.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Objective: To examine the dose-response relationship between average daily temperature and sunlight hours with daily steps across a 35-week period in school-aged children, and to evaluate whether there were differences by sex. Methods: We conducted a follow-up study involving 655 children (50.8% girls, mean age 10.45 ± 0.95) from six public primary schools in Cuenca, Spain. We measured daily steps using Xiaomi Mi Band 3 Smart Bracelets from October 2022 to June 2023 (over 35 weeks). We collected daily average temperature from the local weather station in Cuenca and sunlight hours during the same period. We used ANCOVA models and LOESS regression to examine the dose-response relationship between average daily temperature and daily hours of sunlight with daily steps. Additionally, we performed a multiple linear regression model. Results: Our findings revealed significant variations in daily steps across the 35 weeks. The relationship between environmental factors and daily steps was non-linear, in both girls and boys. The optimal values for higher activity levels were an average temperature of 14°C and 13 hours of sunlight. Furthermore, a 1 ºC increase in temperature was associated with an increase of 74 ± 130 steps/day, while an increase of one hour of sunlight was associated with an increase of 315 ± 237 steps/day. However, sunlight hours may act as a moderating factor. Conclusion: Our study showed a non-linear association between t average daily temperature and sunlight hours with daily steps over a 35-week period. Additional strategies may be necessary to encourage increased physical activity during periods of extreme temperatures or sunlight exposure.

The present study aimed to investigate the effect of solution of ethanol extractions of different microalgae species: Spirulina sp., Dunaliella sp. and Chlorella sp. on the accumulation of biologically active compounds in tomato fruits. Ethanol solution as well as treatment with drinking water were used as a control. Tomato cultivar ‘Belle’ F1 (Enza Zaden) was grown in 25 L pots, in peat substrate (pHKCl 5.5, producer Laflora LTd), polycarbonate greenhouse. Chemical composition – total carotenoids, lycopene and β-carotene content, total phenolics and anthocyanins, organic acids, vitamin C as well as dry matter, pH and soluble solids content – was determined in tomato fruits at the stage of full ripen. The influence of tested extracts on biologically active compounds on quality parameters of tomatoes was different, but no negative effect was observed. As only pH values as well as total phenol content and total soluble solids had statistically significant differences, results can be described with genetical stability of the cultivar.

Robotics offers innovative possibilities at all levels of education, which should be considered when planning the teaching process for certain topics of engineering mathematics in higher education. In this paper, we present a new teaching-learning technique using STEAM-based methods to explore the properties of cycloidal curves for Computer Science Engineering BSc students. Frontal teaching, which is part of the tradition of higher education, has been complemented with teaching methods that meet the generational needs of students: problem-based learning, integration of STEAM-based methods and project-based learning. We have developed a new methodological model that combines the advantages of the traditional teaching method with new forms of teaching that have proven to be effective in teaching Generation Z. The four-stage methodological model uses a variety of didactical approaches because each stage applies a different type of learning technique to make the learning process interesting, motivating and effective. One of the main pillars of the model is the use of Desmos dynamic geometry software to create animations, and the other is the use of educational robotics to support visualisation. The implementation of educational robotics and its potential for teaching cycloidal curves is discussed in detail. The effectiveness of the method was investigated with first-year undergraduate students in computer science engineering. Quantitative studies were carried out to test the effectiveness of the new teaching technique. The experimental results strongly indicate the value of using the four-stage methodological model to implement active learning in the field of cycloidal curves.

This research aims to apply Artificial Intelligence (AI) methods, specifically Artificial Immune Systems (AIS), to design an optimal control strategy for a multivariable control plant. Two specific industrial control approaches are investigated: I-PD (Integral-Proportional Derivative) and PI-D (Proportional-Integral Derivative) control. The motivation for using these variations of PID controllers is that they are functionally implemented in modern industrial controllers, where they provide precise process control. The research results in a novel solution to the control synthesis problem for the industrial system. In particular, the research deals with the synthesis of I-P control for a two-loop system in the technological process of a distillation column. This synthesis is carried out using the AIS algorithm, which is the first application of this technique in this specific context. Methodological approaches are proposed to improve the performance of industrial multivariable control systems by effectively using optimization algorithms and establishing modified quality criteria. The numerical performance index ISE justifies the effectiveness of the AIS-based controllers in comparison with conventional PID controllers (ISE₁ = 1.865, ISE₂ = 1.56). The problem of synthesis of the multi-input multi-output (MIMO) control system is solved, considering the interconnections due to the decoupling procedure.

Despite nearly a century of research on water related issues, water erosion remains one of the greatest threats to soil health and soil ecosystem services around the world. Yet to date, data on water erosion needed to develop mitigation strategies is scarce, especially in the Sahelian regions. The current study therefore sets out to estimate annual soil losses caused by water erosion and to analyze trends over the period of 1981-2020 in the Mékrou watershed, located in the Middle Niger river sub-basin in West Africa. The revised universal soil loss equation, remote sensing and the Geographic Information System (GIS) were deployed in this study. Several types of data were used, including rainfall, soil conditions, topography and satellite images. The estimated average annual amount of water erosion in the Mékrou watershed is 6.49 t/ha/yr over 1981-2020. The dynamics of the ten-year average are highly variable, with a minimum of 3.45 t/ha/yr between 1981 and 1990, and a maximum of 8.50 t/ha/yr between 1991 and 2000. Even though these average soil losses in the Mékrou basin are below the tolerable threshold of 10 t/ha/yr, mitigation actions are needed for prevention. In addition, the spatial dynamics of water erosion are noticeably heterogeneous. The study reveals that 72.7% of the surface area of the Mékrou watershed is subject to slight water erosion below the threshold, compared with 27.3%, particularly in the mountainous south-western part, which is subject to intense erosion above the threshold.

Throughout the Covid19 period, families were forced to stay indoors, adapting to online school-ing, remote work, and virtual social engagements, inevitably altering the dynamics within households. There is a notable increase in mental health challenges in terms of anxiety and de-pression in children and adolescents. This study intends to explore the psychosocial effects of the Covid-19 pandemic in Italian families adopting self- and proxy-report questionnaires on anxiety, anger, and health-related quality of life. The results showed that approximately 20% obtained a clinical anxiety score and only 10% obtained a clinical anger score. There was found a difference in the perception of the quality of life reported by the child and that perceived by the parent. The stepwise regression model showed that total anxiety scores were predicted by sex, quality of life scores from the parents' self-report version and total anger score. Another stepwise regression model identified physiological and social anxiety as the best predictors that impact the quality of life. Parental well-being actively influences the well-being of children, so it is fundamental to implement preventive programmes and promote child well-being providing parents the most adequate support possible.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

The key towards a sustainable future is the reduction of mankind’s impact on natural systems via the development of new technologies and the improvement of source apportionment. Though days, years and seasons are arbitrarily set, their mechanisms are based on natural cycles driven by Earth’s orbital periods. This is not the case for weeks, which are a pure anthropic category and are known from literature to influence emission cycles. For the first time since it started data gathering operations, CO (carbon monoxide), CO₂ (carbon dioxide), CH₄ (methane) and eBC (equivalent black carbon) values detected by the Lamezia Terme WMO/GAW station in Calabria, Southern Italy have been evaluated via a two-pronged approach accounting for weekly variations in absolute concentrations, as well as the number of hourly averages exceeding select thresholds. The analyses were performed on seven continuous years of measurements, from 2016 to 2022. Moreso, the two results have been combined into a new parameter: the hereby defined WDWO (Weighed Distribution of Weekly Outbreaks) normalizes weekly trends of CO, CO₂, CH₄ and eBC on an absolute scale as percentages, with the scope of providing regulators and researchers alike with a new tool meant to better evaluate anthropogenic pollution and mitigate its effects.

Human induced climate change led to the recognition of Community-Based Adaptation (CBA) as one of the remedies in building adaptive capacity and resilience of communities. It recognizes the resources and the skills as well as the agency of communities in shaping the optimal strategy. CBA interventions are vital in addressing community needs and contextual specificities, enable participatory and inclusive engagement and thereby facilitate more profound adaptation impacts. Agent-based modelling (ABM) harbors the potential to be the ideal tool to support developing of tailored adaptation strategies while considering capacities, resources, skills, priorities, needs and the cultural context of local communities. ABM allows to capture the complex relationships among various components within community decision making on CBA actions, the CBA actions themselves and the environment. There exist plenty of tools, however they provide for varying degrees of freedom in agent definition, sensitivity analysis, scalability, experiment design and output analysis to name a few. A set of required key criteria for CBA modelling is developed and all available ABM modelling and simulation tools are assessed for their suitability for CBA. NetLogo emerges as the most fitting tool for incorporating and handling the special features of CBA. It is closely followed by GAMA and Envision. The article provides insights and guidance to researchers and practitioners in selecting ABM tools aligned with the specific requirements of their CBA simulations and projects.

Background: The receptor activator of the nuclear factor-kB (RANK)/RANK ligand (RANKL)/osteoprotegerin (OPG) pathway is a determining pathway in the balance between bone formation and resorption; disruptions in this complex can affect bone metabolism. Methods: This study analyzed the changes in RANKL, OPG and 25(OH)D levels, the RANKL/OPG ratio, and other bone turnover markers (BTM) from diagnosis to complete remission in children with acute lym-phoblastic leukemia (ALL). This is a prospective observational cohort study. This study was carried out in the Instituto Mexicano del Seguro Social in Mexico City. Thirty-three patients (4-17 years) with newly diagnosed B-cell ALL were included. The patients were treated with the HP09 chemotherapy protocol. Children who had previously been treated with corticosteroids were excluded. A pe-ripheral blood sample at diagnosis and remission was collected to determine the 25(OH)D and BTM concentrations. Results: Increased RANKL (p=0.001) and osteocalcin (p

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

Tackling the intricacies of network dismantling in complex systems poses significant challenges. This task has relevance across various practical domains, yet traditional approaches focus primarily on singular metrics, such as the number of nodes in the Giant Connected Component (GCC) or average pairwise connectivity. In contrast, we propose a unique metric that concurrently targets nodes with the highest degree and reduces the GCC size. Given the NP-hard nature of optimizing this metric, we introduce MaxShot, an innovative end-to-end solution that leverages graph representation learning and reinforcement learning. Through comprehensive evaluations on both synthetic and real-world datasets, our method consistently outperforms leading benchmarks in accuracy and efficiency. These results highlight MaxShot’s potential as a superior approach to address the network dismantling problem effectively.

Background: Gender differences characterize the prevalence and attitudes toward weight management. Despite limited evidence suggesting greater weight loss in women with anti-obesity pharmacotherapy, gender-specific analysis remains underexplored. This retrospective study aimed to evaluate the gender-specific response to liraglutide 3.0 mg treatment in people with obesity without type 2 diabetes (T2D). Methods: Data were collected from 47 patients (31 women, 16 men), with age > 18 years, BMI ≥ 30 kg/m^2, absence of T2D, and with exclusion of prior anti-obesity treatment, comorbidities, or bariatric surgery. Only patients who maintained the liraglutide 3.0 mg dose for at least 6 months were included. Results: Both sexes showed significant reductions in weight and BMI at 3 and 6 months. Men achieved greater weight loss (WL), BMI reduction, % WL, WL >5% and >10% than women, and they also showed more significant improvements in metabolic parameters (total and LDL cholesterol, Fibrosis-4 Index FIB-4). No significant gender differences were observed in glucose metabolism or renal function. Conclusion: This study showed a greater therapeutic effect of liraglutide 3.0 mg in men. Given men's higher risk of cardiovascular disease (CVD), and underrepresentation in clinical weight loss programs, these findings may increase male engagement and improve their CVD risk.

Education plays a key role in human societies and the development of nations. Providing social justice in a country creates educational justice, and educational justice grants equal opportunities for growth and prosperity to the members of the society. In reality, there are differences between urban and rural educational facilities, as well as between girls and boys. Deprived and rural areas are full of losses, from economic problems to intellectual and cultural blockages. Failure to enhance these areas leads to further decline in these environments, and one of its consequences in education is the dropout of students. Girls are especially exposed to this problem due to gender discrimination, traditional and religious views, and living conditions. The purpose of this research was to obtain in-depth information about the experiences and reactions of girls in deprived areas and to identify its factors. This case study was conducted in the Khuzestan province of Iran using the grounded theory, and the results of the interviews were categorized after coding and its paradigm model was presented. In the end, solutions were presented to reduce the dropout rate of girls in deprived areas and prevent this problem.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

Many anti-tumor effects of group-specific component-derived macrophage-activating factors (GcMAFs) have been reported; however, the specific mechanisms remain unclear. Controlling tumor-associated macrophages (TAMs) in the tumor microenvironment is essential for cancer treatment. This study assessed the role of GcMAF in macrophage activation, elucidated the mechanisms by which it exerts its anti-tumor effects, and determined its effects on TAMs in the tumor microenvironment. GcMAF-stimulated RAW264.7 macrophages and EMT6 breast tumor cells were co-cultured in a 0.4-µm pore cell culture insert, and gene and protein expression and cell viability were evaluated. DNA microarray analysis of GcMAF-stimulated RAW264.7 cells was conducted. The induction of M2 RAW264.7 cells by interleukin (IL)-4 and IL-13 was analyzed. GcMAF stimulation increased the tumor necrosis factor-α and inducible nitric oxide synthase mRNA and protein levels in RAW264.7 cells but decreased the viability of co-cultured EMT6 cells. These results were confirmed in the M2 RAW264M2.7 cells, suggesting that GcMAF exerts anti-tumor effects by inducing the differentiation of macrophages into the M1 type and reprogramming M2 macrophages to the M1 type. The anti-tumor activity of GcMAF via M2-to-M1 macrophage reprogramming could aid in developing novel cancer immunotherapies.

Continuing the investigation already started (See Farcaş, A.-A.; Bende, A. PCCP 2024, 26, 14937), the light absorption and charge-transfer properties of the dopamine (DA), dopamine zwitterion (called as dopamine-semi-quinone or DsQ) and dopamine-o-quinone (DoQ) adsorbed on the graphene nanoparticle surface have been investigated using the ground state and linear-response time-dependent density functional theories, considering the B97X-D3BJ/def2-TZVPP level of theory. In terms of the strength of molecular adsorption on the surface, the DsQ form has 50 % higher binding energy than that for the DA or DoQ cases (-20.24 kcal/mol vs. -30.41 kcal/mol). The results obtained for electronically excited states and UV-Vis absorption spectra show that the photochemical behavior of DsQ is more similar to DA than that observed for DoQ. Of the three systems analyzed, the DsQ-based complex showed the most active CT phenomenon, both in terms of the number of CT-like states and the amount of charge transferred. Of the first thirty electronically excited states computed for the DsQ case, eleven are purely CT-type and nine are mixed CT and localized (or Frenkel) excitations. By varying the adsorption distance between the molecule and the surface vertically, the amount of charge transfer obtained for DA decreases significantly as the distance increases, for DoQ it remains stable, while for DsQ there are states for which little change is observed, while for others there is a significant change. Furthermore, the mechanistic compilation of the electron orbital diagrams of the individual components cannot describe in detail the nature of the excitations inside the complex.

In the second decade of the 21st century, social media changed the nature of communication and cooperation between participants of the culture services market. They became, among other things, an important marketing instrument in the area of contact with the customers of the cultural offer. However, despite their growing importance in various areas of activity of organisations in the cultural sector, the issue of building the cultural institution's brand equity by social media users is relatively seldom raised. Research on the impact of online consumer activity on brand equity is at an early stage of development. Therefore, this article is an attempt to fill the research gap in this area. The article presents the results of a survey conducted in 2018 on a group of 1021 consumers of cultural services, who at the same time regularly used social media. The statistical analysis carried out and the research results obtained prove that the 3C sustainable system developed by the authors, concerning the activity of consumers of cultural services in social media, stimulates the consumer-based brand equity (CBBE). Statistically significant relations have been observed in particular for CBBE components related to the awareness of a cultural institution's brand and for the relationship related to the perception of its quality. The study opens a review of literature on social media and consumer-based brand equity (CBBE). Next, based on the COBRA model (consumer's online brand-related activities), a proposal of the 3C sustainable system, concerning the activity of consumers of cultural services in social media, has been presented. The further part of the article presents research hypotheses, a conceptual model, research methodology as well as results and conclusions. The last part of the article discusses the results obtained and indicates the existing management implications.

Climate simulations in West Africa have been attributed with large uncertainties. Global climate projections are not consistent with changes in observations at the regional or local level of the Niger basin, making management of hydrological projects in the basin uncertain. This study evaluates the potential of using the quantile mapping bias correction to improve the Coupled Model Intercomparison Project (CMIP5) outputs for use in hydrology impact studies. Rainfall and temperature projections from 8 CMIP5 Global Climate Models (GCM) were bias corrected using the quantile mapping approach. Impacts of climate change was evaluated with bias corrected rainfall, temperature and potential evapotranspiration (PET). The IHACRES hydrological model was adapted to the Niger basin and used to simulate impacts of climate change on discharge under present and future conditions. Bias correction significantly improved the accuracy of rainfall and temperature simulations compared to observations. Nash coefficient (NSE) for monthly rainfall comparisons of 8 GCMs to the observed was improved by bias correction from 0.69 to 0.84. The standard deviations among the 8 GCM rainfall data were significantly reduced from 0.13 to 0.03. Increasing rainfall, temperature, PET and river discharge were projected for all GCMs used in this study under the RCP8.5 scenario. These results will help improving projections and contribute to the development of sustainable climate change adaptation strategies.

This article presents an innovative approach to the design of a safe adaptive backstepping control system. Tailored specifically for underactuated marine robots, the system utilizes simple sensors for enhanced practicality and efficiency. Given their operation in diverse oceanic environments fraught with various sources of uncertainties, ensuring the system's safe and robust behavior holds paramount importance in the control literature. To address this concern, this paper introduces a control strategy designed to ensure robustness at both the kinematic and dynamic levels. By emphasizing the compensation for the system uncertainties, the design integrates a straightforward fuzzy system structure. To further ensure the system's safety, a funnel surface is defined, followed by the design of a suitable nonlinear sliding surface as a function of the funnel and tracking error. Specifically leveraging the Lyapunov function, the study formally establishes the Semi-globally Practically Finite-time Stability of the closed-loop system, validated through simulations conducted on underactuated marine robots.

The number of physical devices connected to the Internet such as vehicles, household appliances and other "things" has been steadily increasing in recent years, thus forming the basis for the Internet of Things (IoT). IoT ecosystem extends beyond country borders and application domains, combining thousands of versatile devices that differ in terms of their structures, capabilities, and available resources. It is therefore not surprising that the landscape of wireless communication technologies and the degree of IoT devices available today is excessively broad and diverse. Interference between networks leads to frame collisions and consequent packet loss. Frame collisions occur when two or more packets overlap in time and frequency and use the same Long Range (LoRa) parameters, i.e. the same Spreading Factor (SF), Bandwidth (BW) and Carrier Frequency (CF). When most devices use the same configuration, collision probability is higher. The probability of frame collisions is also affected by traffic characteristics, particularly the periodicity of the transmission and the payload size. Larger payload sizes and more frequent transmissions accumulate with higher Time on Air (ToA) and channel occupancy [1]. Transmission powers and the location of the gateways also influences this situation. The aim of this experimental work is to verify the effects of collisions and interference in Long Range Wide Area Network (LoRaWAN), regarding the periodicity of transmissions and the payload sizes in a context of an inter-SF interference scenario. And to validate measuring tools like Received Signal Strength Indicator (RSSI), ToA and Packet Delivery Ratio (PDR) in the reliability of a network. We validate our conclusions by analyzing ToA according with RSSI and different data sizes, the RSSI for different SFs and different data sizes and finally the packet loss through the PDR for a better understanding of the reliability of packet transmission in our link. In the end we conclude that in an environment with inter-SF interference, the choice of SFs and packet lengths impacts ToA. When dealing with multiple devices near gateways, different SFs and varying packet lengths can lead to increased latency and longer ToA. Consequently, the risk of packet loss becomes more significant, especially if the signal-to-interference ratio (SIR) is low. This limitation will therefore affect scalability, particularly in Non-Line-Of-Sight (NLOS) scenarios.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.