Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

Introduction: Hypertension is a serious public health problem in Morocco. The objective of this pilot study was to estimate the salt intake of Moroccan adults by measuring 24-hour urinary sodium excretion. Methods: 132 participants were recruited from the central region of Morocco. Sodium, potassium and creatinine levels were measured using the 24-hour urine samples. Additional data included anthropometric measurements and socio-demographic questionnaire. Results: The daily sodium, potassium and creatinine excretions were 2779.1±1334.9 mg, 1350.0±642.8 mg and 820.3 ± 381.2 mg, respectively. Data analysis revealed that 71.2% of the participants had a daily sodium intake more than 2000 mg (5g of salt) recommended by the WHO. The mean of potassium excretion was 1350.0±642.8 mg /day, this average was lower than 3.51g per day recommended by the WHO. Conclusion: Public health measures to reduce sodium and increase potassium consumption in order to decrease the population’s risk of high blood pressure and heart disease are recommended.

The results of the investigation showed that second-order kinetics govern the adsorption process, and the corresponding rate constants were found. To evaluate the parameters related to the adsorption process, the adsorption equilibrium was examined using a variety of mathematical models, such as the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models. The Langmuir isotherm was found to be the best appropriate among all models for describing the adsorption of Cu2+ and Ni2+ ions using bio-nanocomposite beads. The positive values of ΔH° indicate that the adsorption is physical and endothermic, in agreement with experimental results. The negative value of ∆G° shows that the adsorption process is spontaneous. Positive ΔS° values indicate increased randomness at the solid/liquid interface, during adsorption of Cu2+ and Ni2+ cations onto the engineered bio-nanocomposite. The maximum adsorbed amounts of metal ions by the bio-nanocomposite used were 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ from single system. For the binary system, according to the Langmuir isotherm, the maximum adsorbed amounts of Ni2+ and Cu2+ were 357.14 mg/g and 370,37 mg/g, respectively. There is proof that Alginate-Moroccan clay bio-nanocomposites can serve as a different, less expensive source of sorbents for the removal of metal ions from single and binary systems.

In this paper, we generalize Fibonacci quaternion, octonion, sedenion, trigintaduonion, etc. and define Horadam 2^{k}-ions and investigate their properties. Each Horadam (such as Fibonacci, Lucas, Pell) quaternions, octonions and sedenions are Horadam 2^{k}-ions. We also present connection to some earlier works.

A reduction in population sodium (as salt) consumption is one of the most cost-effective strategies to reduce the burden of cardiovascular disease and it is a global health priority. High potassium intake is also recommended to reduce cardiovascular disease. To establish effective policies for setting targets and monitoring effectiveness within each country, the current level of consumption should be known. Greece lacks data on actual sodium and potassium intakes. The aim of the present study was therefore to assess dietary salt (using sodium as biomarker) and potassium intakes in a sample of healthy adults in northern Greece and to determine whether adherence to a Mediterranean diet is related to different sodium intakes or sodium-to-potassium ratio. A cross-sectional survey was carried out in Thessaloniki greater metropolitan area (northern Greece) (n=252, aged 18-75 years, 45.2% males). Participants’ dietary sodium and potassium intakes were determined by 24h urinary sodium and potassium excretions. In addition, we estimated their adherence to Mediterranean diet by the use of an 11-item MedDietScore (range 0-55). The mean sodium excretion was 175 (SD 72) mmol/day, equivalent to 4,220 (1,745) mg of sodium or 10.7 (4.4) g of salt per day and potassium excretion was 65 (25) mmol/day, equivalent to 3,303 (1,247) mg/day. Men had higher sodium and potassium excretions compared to women. Only 5.6% of the sample had salt intake <5g/d, which is the target intake recommended by the WHO. Mean sodium-to-potassium excretion ratio was 2.82 (1.07). There was no significant difference in salt or potassium intake or their ratio across MedDietScore quartiles. No significant relationships were found between salt intake and adherence to Mediterranean diet, suggesting that the perception of the health benefits of the Mediterranean diet does not hold when referring to salt consumption. These results suggest the need for a larger nation-wide survey on salt intake in Greece and underline the importance of continuation of salt reduction initiatives in Greece.

We first explore negative-ion formation in fullerenes C44, C60, C70, C98, C112, C120, C132 and C136 through low-energy electron elastic scattering total cross sections calculations using our Regge-pole methodology. Water oxidation to peroxide and water synthesis from H₂ and O₂ are then investigated using the anionic catalysts C44ˉ to C136ˉ. The fundamental mechanism underlying negative-ion catalysis involves hydrogen bond strength-weakening in the transition state. DFT transition state calculations found C60ˉ numerically stable for both water and peroxide synthesis, C100ˉ increases the energy barrier the most and C136ˉ the most effective catalyst in both water synthesis and oxidation to H2O2.

Bicyclic peptides have attracted the interest of pharmaceutical companies because of their remarkable properties putting them on a new path in medicine. Their conformational rigidity that improves proteolytic stability, leads to rapid penetration into tissues via any possible route of administration and elimination, occurring by renal metabolism, is of great importance for people with a history of liver diseases. In addition, each ring can function independently, making them extremely versatile molecules for further optimization. In this paper we compared the potentiometric and spectroscopic properties studied by UV-Vis, MCD, and EPR, of four synthetic analogues of the bi-cyclic peptide c(PKKHP-c(CFWKTC)-PKKH). In particular we correlated the structural and spectral properties of complexes with coordinating abilities toward Cu(II) ions of MCL (Ac-PKKHPc(CFWKTC)PKKH-NH2) that contains the unbinding cycle and N- and C-terminal linear parts, with two histidine residues, one per part; two monocyclic ligands containing one histidine residue, both in the N-terminal position i.e., MCL2 (Ac-PKKHPc(CFWKTC)PKKS-NH2) and in the C-terminal position i.e., MCL3 (Ac-PKKSPc(CFWKTC)PKKH-NH2), respectively, and the linear structure LNL (Ac-PKKHPSFWKTSPKKH-NH2).

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

This cross-sectional study evaluated the validity of three alternative methods compared to the gold standard 24-h urine collection for estimating dietary sodium intake, a modifiable risk factor for hypertension, among middle-aged and older adults with elevated blood pressure. These included spot urine collection (using Kawasaki, Tanaka, and INTERSALT equations), 24-h dietary recall, and food frequency questionnaire responses, compared against 24-h urine collection in a subset of 65 participants (aged 50–75 years, 58.5 % women, 61.6 % hypertensive) from the DePEC-Nutrition trial. The validity of the methods was assessed using bias, Spearman correlation coefficient (SCC), intraclass correlation coefficient (ICC), and Bland-Altman analysis. Among the alternative methods, spot urine collection using the Kawasaki equation showed the strongest correlation (SCC 0.238; ICC 0.119, 95 % CI -0.079 to 0.323) but it exhibited a significant bias (1414 mg/day, p-value < 0.001) relative to 24-h urine collection. Conversely, dietary surveys had a smaller bias but wider limits of agreement. These findings underscore the complexities of accurately estimating dietary sodium intake using spot urine collection or dietary surveys in this specific population, suggesting that a combination or refinement of existing methodologies might improve accuracy. Further research with larger samples is necessary to develop more reliable methods for assessing sodium intake in this high-risk group.

Abstract: This work is part of the interest of solving the problems of water contamination with last generation pollutants, for which a novel and in an aqueous medium FeBTC material incorporated with magnetite nanoparticles was proposed. That material was synthesized by in situ solvothermal method, the Fe3O4 nanoparticles were added during the Fe-BTC MOF synthesis and used in the drug’s adsorption. The materials were characterized by XRD, FTIR and Raman spectroscopy, and N2-physisorption at 77 K. Fe3O4-FeBTC material showed a maximum adsorption capacity of 357.1 mg g−1 for diclofenac sodium, 70.9 mg g−1 for naproxen sodium, and 122.9 mg g−1 for Ibuprofen. A pseudo-second-order kinetic model can describe the adsorption process, and the thermodynamic study revealed that the adsorption of the three drugs was a feasible, spontaneous, and exothermic process. The incorporation of magnetite nanoparticles in the FeBTC considerably increased the adsorption capacity of pristine FeBTC. Also, hybridization of the FeBTC with magnetite nanoparticles reinforced the most vulnerable part of the MOF, increasing its thermal and aqueous media stability. The electrostatic interaction, H-bonding, and interactions in the open-metal sites played a vital role in drug adsorption. The competition of sites in the multicomponent mixture's adsorption showed selective adsorption at diclofenac sodium and naproxen sodium.

Chronic kidney diseases (CKD) and end stage renal disease (ESRD) are growing threats worldwide. Tissue engineering is a new hope to surpass the current limitations such as the shortage of donor. To do so, the first step would be fabrication of an intact decellularized kidney scaffold. In the current study, an automatic decellularization device was developed to perfuse and decellularize male rats' kidneys using both sodium lauryl ether sulfate (SLES) and sodium dodecyl sulfate (SDS) and to compare their efficacy in kidney decellularization and post-transplantation angiogenesis. After anesthesia, kidneys were perfused with either 1% SDS solution for 4 h or 1% SLES solution for 6 h. The decellularized scaffolds were stained with hematoxylin and eosin (H&E), periodic acid Schiff (PAS), Masson’s trichrome, and alcian blue to determine cell removal and glycogen, collagen and glycosaminoglycans (GAGs) contents, respectively. Moreover, scanning electron microscopy (SEM) was performed to evaluate the cell removal and preservation of microarchitecture of both SDS and SLES scaffolds. Additionally, DNA quantification assay was applied for all groups in order to measure residual DNA in the scaffolds and normal kidney. In order to demonstrate biocompatibility and bioactivity of the decellularized scaffolds, allotransplantation was performed in back muscle and angiogenesis was evaluated. Complete cell removal in both SLES and SDS groups was observed in SEM and DNA quantification assays. Moreover, the extracellular matrix (ECM) architecture of rat kidney in the SLES group was significantly preservation better than the SDS group was shown. The formation of blood capillaries and vessels were observed in the kidney allotransplantations in both SLES and SDS decellularized kidneys. In conclusion, we demonstrated that both SLES and SDS could be promising tools in kidney tissue engineering. The better preservation of ECM than SDS, introduces SLES as the solvent of choice for kidney decellularization. ¬¬

Zinc protection of galvanized steel is initially dissolved in alkaline solutions. However, passive layer is formed over time which protects the steel from corrosion. The behavior of galvanized steel exposed to strong alkaline solutions (pH values of 12.7) with a fixed concentration of sulfate ion of 0.04M is studied. Electrochemical measurement techniques such as corrosion potential, linear polarization resistance and electrochemical impedance spectroscopy are used. Synergistic effect of sulfate ion is also studied together with other anions such as chloride Cl- or bicarbonate ion HCO3- and with other cations such as calcium Ca2+, ammonium NH4+ and magnesium Mg2+. Presence of sulfate ions can depassivate the steel, leading to corrosion density of 0.3 µA/cm2 at the end of the test. The presence of other ions in the solution increases this effect. The increase in corrosion density caused by cations and anions responds to the following order (greater to lesser influence): NH4+&gt;Ca2+&gt;Mg2+ and HCO3- &gt;Cl- &gt;SO42-.

Selenium is one of the inorganic compounds in human and animal nutrition and is involved in the proper functioning of the body. As a micronutrient, it actively contributes to the regulation of various metabolic activities, i.e., thyroid hormone, and protection against oxidative stress and cancer. Selenium anion also plays an essential role in the mechanism of immunity to viral infec-tions. However, this element can also be hazardous, especially in high concentrations. The toxicity of selenium is strongly associated with its chemical form. Se exhibits a narrow concentration window from having a positive to exerting a toxic effect. The daily uptake for humans is in the range of 55-400 µg/day. In higher doses (of the order of 900-1000 µg/day), it negatively affects the human body and causes DNA damage through the formation of free radicals. Increased reactivity of Se anion can also disrupt the integrity and function of DNA-repairing proteins. As the permis-sible concentration of Se in drinking water is 10 µg/L, it is vital to develop sensitive and robust methods of Se detection in aqueous samples.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

In the present work, a portable device system applied in the detection and classification of different metallic ions was proposed and developed, aiming at its application in the monitoring of hydrological systems like rivers, lakes and groundwater. Considering the system features, a portable colorimetric system was developed by using a multispectral optoelectronic sensor. All the technology of quantification and classification of metallic ions using Optoelectronic Multispectral sensors was fully integrated in the embedded hardware FPGA technology and software based on virtual Instrumentation (NI LabView ®). The system was used as a colorimeter by using the chromogen reagent of 1-(2-pyridylazo)-2-naphthol (PAN) as an indicator and the results obtained together with the signal processing and pattern analysis using the method of the linear discriminant analysis, allowed to obtain excellent results in detection and classification of Pb(II), Cd(II), Zn(II), Cu(II), Fe(III) and Ni(II) ions, with almost the same level of performance in relation to those obtained from the UV-VIS spectrometers of high spectral resolution.

The electrochemical oscillation was first observed in the charging process of anolyte in VRFBs. The chronopotentiometry with current ramp results could be used to judge the appearance of electrochemical oscillation. The electrochemical oscillation could be explained in terms of the competition between the growth and the chemical dissolution of V2O5 film in the H2SO4 solution. It was possible to regular the extra power consumption resulted by the electrochemical oscillation. This work might provide new focus on the charging process of the VRFBs and guide for new methods on energy saving.

Low-sodium salt substitute (LSSS) has the potential in regulating sodium and potassium intake and has been available in China market for years. However, its real-world use and impact to sodium\potassium intake is unclear. Baseline data of 4000 adult participants who participated in three similar-designed randomized controlled trails were pooled together for this study. Self-reported awareness and use of LSSS were collected using the uniform questionnaire, and the 24-h urinary sodium and potassium excretion was used to estimate their dietary intake. Mixed-effects models were developed to assess the relationship between LSSS and 24-h urinary sodium and potassium excretion. 32.0% of the participants reported awareness of LSSS and 11.7% reported its current use. After adjusting location, sex, age, and education, compared with the group of participants unaware of LSSS, participants who were aware but not using LSSS and those who were using LSSS had a lower 24-h urinary sodium excretion by –356.1(95% CI: –503.9, –205.9) mg/d and –490.6(95% CI: –679.2, –293.7), respectively (p&lt;0.001). No significant difference was found for 24-h urinary potassium excretion and sodium-to-potassium ratio among the three groups (p&gt;0.05). In conclusion, although associated with lower sodium intake, the awareness and real-world use of LSSS are still very low in China.

The Conus genus includes around 500 species of marine mollusks with a peculiar production of venomous peptides known as conotoxins (CTX). Each species is able to produce up to 200 different biological active peptides. Common structure of CTX is the low number of aminoacids stabilized by disulfide bridges and post-translational modifications that give rise to different isoforms. µ and µ-O CTX are two isoforms that specifically target voltage-gated sodium channels. These, by inducing the entrance of sodium ions in the cell, modulate the neuronal excitability by depolarizing plasma membrane and propagating the action potential. Hyperxcitability and mutations of sodium channels are responsible for perception and transmission of inflammatory and neuropathic pain states. In this review, we describe the current knowledge of µ-CTX interacting with the different sodium channels subtypes, the mechanism of action and their potential therapeutic use as analgesic compounds in the clinical management of pain conditions.

ZnS-CdS composite nano-powder doped with (0.01 mol %) Cobalt has been collected by a co-precipitation process at 300 K. The sample is characterized by structural, combined spectroscopic methods and magnetic studies. The prepared samples were belonging to cubic structure no impurity phases were observed. Doping of cobalt increase the neighborhood strain assessment and a decreases lattice constants decides from x-ray diffraction data. The crystallite size is 10.42nm. From UV-absorption and EPR studies revealed that the energy band gap of Co2+ doped ZnS-CdS composite nanopowder and extension of sp-d exchange interactions and common d-d transitions. The variation in the energy bandgap varies as a function of cobalt concentration is due to structural modification. Photoluminescence spectrum reveals the defect-related emissions and shows the formation of luminescence. FT-IR spectrum confirmed the feature vibrational manner of Zn, Cd, O–H and sulfide ions are in the host lattice. The doping-induced magnetic properties are studied by vibrating sample magnetometer which matches with the theoretical values besides ferromagnetic nature. Magnetic studies confirm the ferromagnetic nature of the material. Surface morphology and chemical homogeneity studies were carried out by using SEM with EDAX. Transmission electron microscope recommends the crystalline nature of nanoparticles, with average particle size is of the order of 20-100nm.

Significant advances in Penning trap measurements of atomic masses and mass ratios of the proton, deuteron, triton, helion, and alpha-particle have occurred in the last five years. These include a measurement of the mass of the deuteron against 12C with 8.5 x 10-12 fractional uncertainty; resolution of vibrational levels of H2+ as mass and the application of a simultaneous measurement technique to the H2+/D+ cyclotron frequency ratio, yielding a deuteron-proton mass ratio at 5 x 10-12; new measurements of HD+/3He+, HD+/T+ and T+/3He+ leading to a tritium beta-decay Q-value with an uncertainty of 22 meV, and atomic masses of the helion and triton at 13 x 10-12; and a new measurement of the mass of the alpha-particle against 12C at 12 x 10-12. Some of these results are in strong disagreement with previous literature values. Their impact in determining a precise proton/electron mass ratio and electron atomic mass from spectroscopy of the HD+ molecular ion is also discussed.

Free volume is an extremely important intrinsic defect in polymers. Structurally, the free volume is the randomly distributed holes in the polymer molecular chain segments. From the perspective of molecular movement, it is also the space needed for the movement of molecular segments. In proton exchange membrane fuel cells, the free volume is also the space needed for the directional conduction of protons. Irradiation grafting sulfonated polyvinylidene fluoride (PVDF) is one of the methods to produce proton exchange membrane with good proton channel rate. Using the LYS-1 program, based on the linear absorption coefficient and backscatter coefficient models, the percentage of annihilated positrons in PVDF in the two-layer model and the three-layer model was studied, and comparing the two fitting results it is determined that the model closest to the positron annihilation percentage required by the PALS experiment is the two-layer model, which allows the percentage of positrons that are annihilated in PVDF films with a thickness of 100 μm to reach 46% using the high energy positron source ⁴⁴Ti without using the positron moderator. Using positron annihilation lifetime spectrum (PALS) analysis methods, based on Eldrup's classical model of free volume, the influence of absorbed doses of α particles on the free volume and crystallinity of PVDF was investigated, respectively. Based on the two test results the model of cross-linking and degradation of polyvinylidene fluoride irradiated by α particles was determined. Afterwards, X-ray diffraction (XRD) methods was used to study the change of PVDF crystal area before and after irradiation. The XRD results are consistent with the results measured by PALS.

The possibilities of manufacturing batteries with Nafion 117 membranes in the Na⁺-form intercalated by mixtures of non-aqueous organic solvents used both as electrolyte, separator and binder were investigated. Electrochemical stability of various organic solvent mixtures based on N,N-dimethylacetamide, ethylene carbonate, propylene carbonate, tetrahydrofuran was characterized. It was shown that sodium battery based on Nafion-Na membrane intercalated by mixture of ethylene carbonate ‑ propylene carbonate with Na₃V_1.9Fe_0.1(PO₄)₃/C positive electrode is characterized by a discharge capacity of ca. 110 mAh g^-1 (C/10) at room temperature and shows the ability to cycle for a long time. Batteries with Nafion membrane electrolytes, containing N,N-dimethylacetamide were characterized by capacity fading during cycling, which is due to the interaction of N,N-dimethylacetamide and a negative sodium electrode.

In this work, we have studied microstructure and unusual ferromagnetic behavior in cobalt (Co)-implanted epitaxial tin dioxide (SnO2) films. The study was aimed to provide a comprehensive understanding of the interplay between cobalt implant distribution, crystal defects, such as oxygen vacancies, and magnetic properties in Co-implanted SnO2 films, which has potential applications in spintronics and memristor devices. The scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometry (VSM), differential thermo-magnetic analysis (DTMA), and ferromagnetic resonance (FMR) were employed for investigations of SnO2 films implanted with 40 keV Co+ ions at room or the elevated temperatures of substrate. The experimental data showed that the Co ion implantation with high fluence of 1.0 1017 ions/cm2 induces significant changes in the microstructure of SnO2 films, leading to the appearance of ferromagnetism with the Curie temperature significantly above room temperature. Strong influence of implantation temperature and subsequent high-temperature annealing in air or in vacuum on magnetic properties of Co-implanted SnO2 films were established. Moreover, the chemical effect of ethanol on FMR spectra were observed. The obtained results are discussed within the model of two magnetic layers with different concentration and valence states of the implanted cobalt and with high content of oxygen vacancies.

In the context of circular economy that recommends the most efficient use of waste, algae wastes have a huge potential for valorisation. In this study, algae wastes obtained after alkaline extraction of active compounds from two types of marine algae (green algae – Ulva sp. and red algae – Callithamnion sp.), were used as biosorbents to remove metal ions from aqueous effluents. Their efficiency in the biosorption processes was tested for Zn(II), Cu(II) and Co(II) ions, considered technologically valuable metal ions. The batch mono-component experiments performed under optimal conditions (pH = 5.0; 4.0 g biosorbent/L; 22 ± 1C), showed that more than 75 % of the metal ions are removed when their initial concentration is less than 1.25 mmol/L. The very good fit of the experimental data with the pseudo-second order kinetic model and Langmuir isotherm model, and the high values obtained for the maximum biosorption capacity (qmax: Cu(II) (0.52 mmol/g) &gt; Zn(II) (0.41 mmol/g) &gt; Co(II) (0.39 mmol/g) for G-AWB, and qmax: Cu(II) (1.78 mmol/g) &gt; Zn(II) (1.72 mmol/g) &gt; Co(II) (1.66 mmol/g) for R-AWB) highlights the potential use of these biosorbents to remove such technologically valuable metal ions from industrial wastewater. This possibility was tested using industrial wastewater samples obtained from the metal coating industry. Quantitative removal (&gt; 91 %) of Zn(II), Cu(II) and Co(II) ions was obtained when their initial concentration was adjusted to 50 mg/L. Also, the rapid and efficient desorption of these metal ions from loaded-biosorbents, by simple treatment with small volumes of HNO3 (10-1 mol/L), further emphasizes the possibility of their recovery and reuse in the technological circuit. The results included in this study indicate that algae wastes have the potential to be used in industrial effluents decontamination processes and opens new perspectives for the implementation of circular economy principles.

The substrate N1, N3, N5 -tris(2-hydroxyphenyl)benzene-1,3,5-tricarboxamide (Sensor A) was prepared in the reaction of 1,3,5-benzenetricarboxylic acid (trimesic acid) and o-aminophenol in ethanol. The prepared organic sensor fulfills the chemiluminescent requirements including luminophore, spacer, and suitable binding receptor that distress the probe's luminescent features, providing selective and sensitive detection of mercury and iron ions in aqueous solutions. The sensor selectively detects mercury and iron ions in a water matrix containing various metal ions including sodium, calcium, magnesium, zinc, and nickel. Strong and immediate binding was observed between mercury ions and the substrate at pH 7.0 with a binding affinity toward Hg (II) enhanced by nine folds higher than that observed for iron sensor binding affinity, which makes the substrate a distinctive luminescence sensor for mercury detection at ambient conditions. The sensor shows a linear response toward Hg (II) in the concentration range from 4.2 x 10-5 to 2.0 x 10-8 M with a limit of detection of 1.0 x 10-8 M. Further, Sensor A provides linear detection for iron ions in the range from 1.5 x 10-3 to 1.5 x 10-8 M. The measured adsorption capacity of Sensor A toward mercury ions ranged from 1.25 to 1.97 mg/g and the removal efficiency from water samples reached 98.8% at pH 7.0. The data demonstrate that Sensor A is an excellent probe for detecting and removing mercury ions from water bodies.

Abstract The global concern about the leather industries is increasing as the leather industries grow bigger each year. These industries face a very challenging task with an increase in stringent pollution control regulation enforced by various bodies due to environmental concern and human risks. The chromium salts are the most widely used chemical for the tanning process in leather industries, about 35% of chromium used for the tanning process remain as metal and discharge to wastewater stream. The removal and recovery of this quantity of wasted chromium are necessary for environmental pollution control and economic reason. This paper sheds light on the chromium recovery and reuse system of Chromium salts in tanning wastewater by using NaOH as an effective chemical precipitation method to regenerate chromium solution, adapted chrome recovery plant, and evaluated the system technically and economically.

In this work, a colorimetric indicator based on gold nanoparticles (AuNP) and a biodegradable and eco-friendly polymer (sodium alginate, Alg.), has been developed, for the real-time detection of fish spoilage products. AuNP and colorimetric indicator were characterized by: UV-Vis, FTIR spectroscopies, TGA, DSC, XRD, TEM, and colorimetry. The UV-Vis spectrum and TEM showed the successful synthesis, the spherical shape, and the size of AuNPs. Results indicated color changes of the indicator in packaged fish on day 9 of storage at refrigerated temperature (5ºC). These results showed the successful application of colorimetric indicator in the detection of TVB-N in packaged fish.

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

(200 words) Imidazolium ionic liquids containing acetylacetone, thenoyltrifluoroacetone, or 8-hydroxyquinoline, respectively, were used as the extracting agents for the separation of traces of iron (III) from its aqueous solutions with or without citric and oxalic acids. The results show that 8-hydroxyquinoline in imidazolium ionic liquids extract iron quantitatively from all the tested solutions including complexing ones, regardless indications of unexpected iron behavior/speciation.

We present a critical analysis of the mechanism of reversible hydrogen evolution reaction based on thermodynamics of hydrogen processes considering atomic and ionic species as intermediates. Clear distinction between molecular hydrogen evolution/oxidation (H$_2$ER and H$_2$OR) and atomic hydrogen evolution/oxidation (HER and HOR) reactions is made. It is suggested that the main reaction describing reversible H$_2$ER and H$_2$OR in acidic and basic solutions is: $\ce{H3O^+} + 2e^- \xrightleftharpoons{\mathrm{({H}_{2}^{+}})_{ad}} \ce{H2} + \ce{OH^-}$, which proceeds via the formation of hydrogen molecular ion as intermediate and its potential is $E^{0}$ = 0.414~V (at the standard Hydrogen electrode SHE scale). We analyse experimentally reported data with models which provide \emph{quantitative} match (R.J.Kriek et al., Electrochem. Sci. Adv. e2100041 (2021)). The experimentally observed slope of $\lg(Current)$ vs. $Potential$ equal to $\approx 30$~mV/dec corroborates the presented model of H$_2$ER/H$_2$ER based on \ce{H2$^+$} as intermediate.

A novel type of graphene-like quantum dots, synthesized by oxidation and cage-opening of C60 buckminsterfullerene, has been studied as a fluorescent and absorptive probe for heavy-metal ions. The lattice structure of such unfolded fullerene quantum dots (UFQDs) is distinct from that of graphene since it includes both carbon hexagons and pentagons. The basic optical properties, however, are similar to those of regular graphene oxide quantum dots. On the other hand, UFQDs behave quite differently in the presence of heavy-metal ions, in that multiple sensitivity to Cu2+, Pb2+ and As(III) was observed through comparable quenching of the fluorescent emission and different variations of the transmittance spectrum. By dynamic light scattering measurements we confirmed, for the first time in metal sensing, that this response is due to multiple complexation and subsequent aggregation of UFQDs. Nonetheless, the explanation of the distinct behaviour of transmittance in the presence of As(III) and the formation of precipitate with Pb2+ require further studies. These differences, however, also make it possible to discriminate between the three metal ions in view of the implementation of a selective multiple sensor.

The research aims to resolve water pollution generated by dye wastewater. In this paper, the aminated sodium lignosulfonate (AELS) was prepared through the Mannich reaction, and the synthesis conditions were optimized using orthogonal experiments to determine the best amination conditions. The successful preparation of AELS was demonstrated through the use of FT-IR, XRD, TG, SEM and XPS characterization techniques. Then, the adsorption capacity of Methyl blue (MB) by AELS was compared in a range of different circumstances, like pH, adsorbent dose, initial concentration, time, and temperature. Additionally, the kinetics, isotherms, and thermodynamic properties of the AELS adsorption for MB were studied and discussed. The results indicated that the fitting results were consistent with the pseudo-second-order kinetic model and Langmuir isotherm model, in accordance with the mechanism of single-molecular-layer chemisorption. And the adsorption of MB by AELS was a spontaneous and endothermic process. Upon completion of five adsorption experiments, the adsorption capacity of MB by AELS was determined to be 107.95 mg g-1, which was 5.3% lower than the first experiment. This research promotes the effective use of natural resources and allows for the sustainable use of lignin and the advancement of new applications for it.

The effect of chemical degradation of a sodium alginate solution and the possibility of encapsulation of paprika oleoresin were investigated. To produce sodium alginate oligomers, a depolymerization process was performed using hydrogen peroxide as a decomposition factor. The characteristics of the samples were obtained by measuring the contact angle of the surface, the surface tension of solutions, as well as thermal decomposition in thermo - gravimetric analysis. The obtained solution of alginate oligomers served as the carrier material for immobilization of capsaicin. Capsules were prepared by ionic gelation using a calcium chloride solution as a crosslinking agent. In this way, capsules without and with the core (capsaicin) were prepared and their ability to scavenge free radicals (DPPH) and iron-reducing properties (FRAP) were determined. The stability of the capsules was examined under conditions of the gastric and small intestine. It was found that alginate oligomers can be used in the encapsulation of bioactive compounds and the efficiency is above 80%. Capsule production from alginate oligomers affected their thermal stability. The use of alginate derivatives as a carrier increases the antioxidant properties of the finished product, as well as its ability to reduce iron ions. The use of alginate oligomers as a coating material prevents the active substance from being released too early in the conditions of the small intestine, prolongs the stability of the capsules, and supports their durability in gastric conditions.

Sodium-potassium (NaK) liquid alloy is a promising candidate for use as anode material in sodium batteries because of its fluidity, which effectively suppresses the growth of sodium or potassium dendrites. However, the poor wettability of the NaK liquid alloy on conventional metal substrates is unfavorable for cell fabrication due to its strong surface tension. In this paper, low-density and low-cost fluorinated aluminum foam is used as a substrate support material for NaK liquid alloy. By combining low surface tension NaK@C with fluorinated aluminum foam, we obtain a uniformly distributed and structurally stable electrode material. The composite electrode has a cycling stability of more than 3000 hours in a symmetrical cell. Furthermore, when coupled with a sulfurized polyacrylonitrile cathode in carbonate electrolyte, it maintains excellent stability even after 800 cycles, with 72% of capacity retention.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

Due to their well-defined plasmonic properties, gold nanorods (GNRs) can be fabricated with optimal light absorption in the near-infrared region of the electromagnetic spectrum, which make them suitable for cancer-related theranostic applications. However, their controversial safety profile, as a result of surfactant stabilization during synthesis, limits their clinical translation. We report a facile method to improve GNR biocompatibility through the presence of sodium dodecyl sulfate (SDS). GNRs (120 x 40 nm) were synthesized through a seed-mediated approach, using cetyltrimethylammonium bromide (CTAB) as a cationic surfactant to direct the growth of nanorods and stabilize the particles. Post-synthesis, SDS was used as an exchange ligand to modify the net surface charge of the particles from positive to negative while maintaining rod stability in an aqueous environment. GNR cytotoxic effects, as well as the mechanisms of their cellular uptake, were examined in two different cancer cell lines, Lewis lung carcinoma (LLC) and HeLa cells. We not only found a significant dose-dependent effect of GNR treatment on cell viability but also a time-dependent effect of GNR surfactant charge on cytotoxicity over the two cell lines. Our results promote a better understanding of how we can mediate the undesired consequences of GNR synthesis byproducts when exposed to a living organism, which so far has limited GNR use in cancer theranostics.

Background: Sodium intake has been related to several adverse health outcomes; such as, hypertension, and cardiovascular diseases. Processed foods are major contributors to the population’s dietary sodium intake. The aim of the present study was to determine sodium levels in Mexican packaged foods; also to evaluate the proportion of foods that comply with sodium benchmark targets set by the UK Food Standards Agency (UK FSA) and those set by the Mexican Commission for the Protection of Health Risks (COFEPRIS). We also evaluated the proportion of foods that exceeded the Pan American Health Organization (PAHO) targets. Methods: This was a cross-sectional study that comprised data collected from the package of 2,248 processed foods from selected supermarkets of Mexico. Results: Many processed food categories contained excessive amount of sodium, being the processed meats (ham, bacon and sausages) those that have the highest concentrations. The proportion of foods classified as compliant in our sample was lower for international targets (FSA UK and PAHO) compared to the Mexican COFEPRIS criteria. Conclusions: These data provide a critical baseline assessment for monitoring sodium levels in Mexican processed foods.

Population studies have demonstrated an association between sodium (Na) and po-tassium (K) intake and levels of blood pressure (BP) and cholesterol. The aim of this study was to describe the dietary intake and distribution of Na and K in Mexicans, and their as-sociation with metabolic risk outcomes. We analyzed a national survey that included 4,219 participants. Dietary information was obtained through a 24-hour recall. Foods and beverages were classified based on the degree of processing. BP and biomarkers in blood and urine were measured. The mean intake (mg/d) of Na was 1512 in pre-schoolchildren, 2844 in schoolchildren, 3743 in adolescents, and 3132 in adults. The mean intake of K was 1616 in pre-schoolchildren, 2256 in schoolchildren, 2967 in adolescents, and 3401 in adults. Processed and ultra-processed foods (UPF) contribute to sodium intake: 49% in preschool and schoolchildren, 47% in adolescents, and 39% in adults. Adults in the fourth quartile of sodium intake had lower serum concentrations of cholesterol (181.4 mg/dL) and HDL-c (35.5 mg/dL). The Mexican population has high Na and low K intakes. There is a relationship between Na sodium consumption and cholesterol, and LDL levels. UPF contributes to almost 40% of the sodium consumed by Mexicans.

In this study, the effect of NaOCl (10–200 ppm of Cl2) on the inactivation of human norovirus (HuNV) GII.4 and hepatitis A virus (HAV) in groundwater was investigated using PMA/RT­qPCR. Initially, 4.00 log copies/μL of HuNV GII.4 or 5.50 log copies/μL of HAV were artificially inoculated in ground water. The titers of HuNV GII.4 and HAV decreased significantly (p < 0.05) with increasing Cl2 concentrations. Ground water was treated with 10, 30, 50, 100, 150, and 200 ppm of Cl2, and the viable HuNV GII.4 was significantly (p < 0.05) reduced to 3.28 (0.21 log reduction), 3.18 (0.31 log reduction), 3.01 (0.48 log reduction), 2.75 (0.74 log reduction), 2.54 (0.95 log reduction), and 2.34 (1.15 log reduction) log copies/μL, respectively. The viable HAV was also significantly (p < 0.05) reduced to 4.99 (0.23 log reduction), 4.76 (0.46 log reduction), 4.55 (0.67 log reduction), 4.21 (1.01 log reduction), 3.89 (1.33 log reduction), and 3.64 (1.58 log reduction) log copies/μL, respectively. The decimal reduction time (D-value) (1-log reduction) of HuNV GII.4 and HAV infectivity in ground water was predicted as 116.7 and 98.9 ppm of Cl2, respectively using the first-order kinetics model (HuNV GII.4 ; y = - 0.0054x + 3.3585, R2= 0.97, HAV ; y = - 0.0091x + 5.0470, R2= 0.97). The result specifically suggests that 150–200 ppm Cl2 can potentially be used for the inactivation of > 1 log copies/μL HuNV GII.4 and HAV in ground water.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

Arthrospira platensis is a class of microalgae with high economic value. Its high adaptability, high photosynthetic efficiency, and fast growth rate make it one of the few microalgae that can be cultivated on a large scale. Therefore, using the selenium enrichment property of Arthrospira platensis to cultivate selenium-enriched Arthrospira platensis will not only enhance the physiological efficacy of Arthrospira platensis but also increase its economic value significantly. In this study, we investigated the effects of sodium selenite on the growth and photosynthetic performance of Arthrospira platensis selenium by setting different amounts and methods of sodium selenite addition, and we explored the optimal culture conditions. The results showed that the experimental group treated with sodium selenite at 120 mg/L had the fastest growth, and the contents of soluble protein, phycocyanin, and Chlorophyll a increased by approximately 67.9%, 1.44 times, and 38.8%, respectively, compared to the control group. Superoxide dismutase (SOD) and catalase (CAT) activity increased by 1.88-fold and 65%, respectively, and malondialdehyde (MDA) levels were reduced by 62% compared to the control group. The results of the OJIP assay showed that the J and I points were significantly higher at the batch addition and treatment concentration of 120 mg/L, with the rate of QA being reduced and the proportion of the slowly reduced PQ pool being increased. The values of the maximum light energy conversion efficiency (Fv/Fm) per unit of reaction center were higher in both sodium selenite treatment groups than in the control group, indicating that the light energy conversion efficiency of Arthrospira was promoted under all concentration treatment conditions. The batch addition of sodium selenite at concentrations less than 120 mg/L resulted in significantly higher ABS/RC values than the control, and they were far superior to the one-time addition method. The reason for this may have been that the batch addition of sodium selenite at low concentrations increased the light absorption capacity of the unit reaction center of the Arthrospira PSII, resulting in a rise in captured light energy, a rise in the energy captured by the reaction center for electron transfer (ETo/RC), a decrease in the energy dissipated in the absorption of light energy by the reaction center (DIo/RC), and an increase in the photosynthetic performance index (PI abs).

Rechargeable aqueous Zn-ion batteries (ZIBs) have attracted considerable attention owing to their high theoretical capacity of 820 mA h g‒1, low cost and intrinsic safety. However, the electrolyte leakage and the instability issues of Zn negative electrodes originating from side reactions between the aqueous electrolyte and Zn negative electrode, not only restricts the battery stability but also results in short-circuit of aqueous ZIBs. Herein we report a flexible and stable N-isopropylacrylamide/sodium alginate (N-SA) gel electrolyte, which possesses high mechanical strength and high ionic conductivity of 2.96×10‒2 S cm‒1, and enables the Zn metal negative electrode and MnO2 positive electrode to reversibly and stably cycle. Compared to the liquid electrolyte, the N-SA hydrogel electrolyte can effectively form a uniform Zn deposition and suppress the generation of irreversible by-products. The assemble symmetric Zn/Zn cells at a current density of 1 mA cm‒2 shows a stable voltage profile, which maintains a low level of about 100 mV over 2600 h without an obvious short circuit or any overpotential increasing. Specially, the assembled Zn/N-SA/MnO2 batteries can deliver a high specific capacity of 182 mAh g‒1 and maintain 98% capacity retention after 650 cycles at 0.5 A g‒1. This work provides a facile method to fabricate high-performance SA-based hydrogel electrolytes that illustrates their potential for flexible batteries for wearable electronics.

Background: Exposure to inorganic arsenic (iAs) remains a global public health problem. The liver is the main target organ of arsenic, leading to arsenic-induced liver fibrosis. Autophagy is involved. Phosphatase and tensin homology deleted on chromosome ten (PTEN) may participate in arsenic-induced liver fibrosis by regulating autophagy, but the exact mechanisms remain unclear. We established a mouse model of arsenic poisoning through the drinking water, and a fibrosis model using the huma stellate cell (HSC) line LX-2, which was exposed to NaAsO₂ for 24h. HE and Masson staining was adopted to observe the degree of liver fibrosis. The cells were transfected using PTEN overexpression plasmid. Western blot and qRT-PCR were used to determine the levels of protein/mRNA expression. The in vivo results were confirmed in HSCs exposed to NaAsO₂, with changes suggesting fibrosis as seen in mice. NaAsO₂ upregulated the expression of the autophagic markers microtubule-associated protein light chain A/B (LC3), recombinant human autophagy effector protein (Beclin-1), hairy and enhancer of split homolog-1 (HES1), but downregulated PTEN. α-smooth muscle actin (α-SMA) expression was significantly upregulated in all NaAsO₂ groups. PTEN overexpression altered NaAsO₂-induced autophagy which LC3, Beclin-1 were downregulated. Notch1, HES1, α-SMA, and collagenⅠexpression were all downregulated in the NaAsO₂ groups. In conclusion, PTEN overexpression might decrease autophagy and inhibit fibrosis progression caused by this toxin. The NOTCH1/HES1 pathway is likely to be involved in this process. Most previous studies did not investigate PTEN and arsenic-induced liver fibrosis specifically. The present study highlights the importance of targeting PTEN for the management of arsenic exposure.

The pharmacokinetics of salicylic acid (SA) in sheep was evaluated following intravenous (IV) and oral administration of sodium salicylate (sodium salt of salicylic acid) at different doses. Six healthy sheep were administered sodium salicylate (SS) IV at doses of 10, 50, 100 and 200 mg/kg body weight and another six sheep were drenched with 100 and 200 mg/kg of SS orally. Both studies were randomised crossover trials. A one-week washout period between each treatment was allowed in both studies. Blood samples were collected at 0, 15, 30 minutes and 1, 2, 4 and 6 hours after IV and oral SS administrations. Plasma SA concentrations were determined using high performance liquid chromatography with diode array detection method. Pharmacokinetic variables were calculated in a non-compartmental model. The elimination half-life (T_{1/2 el}) of SA after IV administration of 200 mg/kg SS was 1.16 ± 0.32 hours. Mean bioavailability of SA was 64%, and mean T_{1/2 el} was 1.90 ± 0.35 hours, after 200 mg/kg of oral SS. The minimum plasma SA concentration (16.8 µg/mL) required to produce analgesia in humans was achieved after IV administration of 100 and 200 mg/kg SS in sheep for about 0.17 hour in this study. Experiments on pharmacokinetic-pharmacodynamics modelling are required to determine the actual effective plasma concentration range of SA in sheep.

Samples of ZrO2 ceramics with different concentrations of impurity titanium ions were synthesized by mixing powders of zirconium and titanium oxides in various mass ratios. The phase composition and surface morphology of the studied ceramics were determined by X-ray phase analysis and scanning electron microscopy. It was found that irradiation of samples with xenon ions (220 MeV) with fluences 1010 and 1012 ion/cm2 leads to a decrease in the intensity of the pulse cathodoluminescence band at 2.5 eV. It is shown that ion irradiation causes the appearance of a new peak of thermoluminescence at 450-650 K of a non-elementary form associated with radiation-induced traps of charge carriers. In contrast to electron irradiation, an increase in the fluence of ions leads to a decrease in the intensity of this peak. In contrast to electron irradiation, an increase in the fluence of ions leads to a decrease in the intensity of this peak. A complex nonmonotonic dependence of the cathode and thermoluminescence intensity on the dopant concentration was found, which may be due to the effects of concentration quenching and aggregation of defective centers.

Plazomicin is a recently U.S. Food and Drug Administration (FDA)-approved semisynthetic aminoglycoside. Its structure consists of a sisomicin scaffold modified by adding a 2(S)-hydroxy aminobutyryl group at the N1 position and a hydroxyethyl substituent at the 6′ position. These substitutions produced a molecule refractory to most aminoglycoside-modifying enzymes. The main enzyme within this group that recognizes plazomicin as substrate is the aminoglycoside 2′-N-acetyltransferase type Ia [AAC(2′)-Ia], which reduces the antibiotic’s potency. Designing formulations that combine an antimicrobial with an inhibitor of resistance is a recognized strategy to extend the useful life of existing antibiotics. We have recently found that several metal ions inhibit acetylation of numerous aminoglycosides catalyzed by the aminoglycoside 6′-N-acetyltransferase type Ib [AAC(6′)-Ib]. In particular, Ag1+, which also enhances the effect of aminoglycosides by other mechanisms, is very effective in interfering with AAC(6′)-Ib-mediated resistance to amikacin. Here we report that silver acetate is a potent inhibitor of AAC(2′)-Ia-mediated acetylation of plazomicin in vitro, and it reduces resistance levels of Escherichia coli carrying aac(2′)-Ia. The resistance reversion assays produced equivalent results when the structural gene was expressed under the control of the natural or the blaTEM-1 promoters. The antibiotic effect of plazomicin in combination with silver was bactericidal, and the mix did not show significant toxicity to human embryonic kidney 293 (HEK293) cells.

Isobaric ions having the same mass-to-charge ratio cannot be separately identified by mass spectrometry (MS) alone, but this limitation can be overcome using hydrogen-deuterium exchange (HDX) in microdroplets. Because isobaric ions may contain a varied number of exchangeable sites and different types of functional groups, each one produces a unique MS spectral pattern after droplet spray HDX without the need for MS/MS experiments or introduction of ion mobility measurements. As an example of the power of this approach, isobaric ions in urinary metabolic profiles are identified and used to distinguish between healthy individuals and those having bladder cancer.

The color of a thin copper oxide layer formed on a copper plate was transformed from reddish-brown into blue-purple by irradiation with 5 keV Ar+ ions to a fluence as low as 1 1015 Ar+ cm–2. In the unirradiated copper oxide layer, the copper valence state of Cu2+ as well as Cu+ and/or Cu0 was included as indicated by the presence of a shake-up satellite line in a photoemission spectrum. While for the irradiated one, the satellite line decreased in intensity, indicating that irradiation resulted in the reduction from Cu2+ to Cu+ and/or Cu0. Furthermore, nuclear reaction analysis using a 16O(d, p)17O reaction with 0.85 MeV deuterons revealed a significant loss of oxygen (51015 O atoms cm–2) in the irradiated layer. Thus, the chromatic change observed in the present work originated in the irradiation-induced reduction of a copper oxide.

The emission of mercury (II) from coal combustion and other industrial processes continues to be a concern and have local impact on water resources. The detection of these ions in water with sensitive but rapid testing methods is desirable for environmental screening and fieldwork. Nanoparticles of various chemistries have shown promise for this purpose, as they can be used in simple colorimetric analyses. Silver nanoprisms were chemically synthesized resulting in a blue reagent solution, that transitioned towards yellow and colorless solutions when exposed to Hg²⁺ ions at various concentrations. A rapid galvanic reduction of Hg²⁺ onto the nanoprism surfaces is apparently responsible for a change in shape towards spherical nanoparticles, leading to the change in color. There were no interferences by other metal ions in solution, and pH had minimal effect in the range of 6.5 to 9.8. The silver nanoprism reagent provided a detection limit of approximately 0.5 µM (100 µg/L) for mercury (II), which compares favorably with other nanoparticle-based techniques. Further optimization may reduce this detection limit.

In this work we present a versatile, rapid, and low-cost manufacturing technique to develop bioceramic scaffolds that could enhance bone tissue regeneration via microwave preparation using a commercial microwave oven. The scaffolds were prepared combining hydroxyapatite and water glass (sodium trisilicate solution), foamed by using a microwaves oven and then characterized by means of SEM-EDS, mechanical properties, infrared spectroscopy (ATR-FTIR), density and stability test in water. Furthermore, in vitro tests were performed to verify the affinity of osteoclast cells versus the so prepared scaffold. The morphology of the samples showed interconnected pores suitable for promoting tissue regeneration and vascularization while specific mechanical properties were preserved. The physicochemical characterization and the in vitro tests presented promising results for bone regenerative applications.

Risk of cardiovascular disease (CVD), common in childhood cancer survivors (CCSs), may be affected by diet. We assessed sodium (Na) and potassium (K) intake, estimated from food frequency questionnaires (FFQs) and morning urine spots, and its associations with cardiovascular risk in CCSs. We stratified CCS into three risk profiles based on A) personal history (CVD, CVD risk factors, or CVD risk free), B) body mass index (obese, overweight, or normal/underweight), and C) cardiotoxic treatment (anthracyclines and/or chest irradiation, or neither). We obtained a FFQ from 802, and sent a spot urine sample collection kit to 212, of which 111 (52%) returned. We estimated Na intake 2.9 g/day based on spot urine and 2.8 g/day based on FFQ; estimated K intake was 1.6 g/day (spot urine) and 2.7 g/day (FFQ). CCSs with CVD risk factors had a slightly higher Na intake (3.3 g/day), than CCSs risk free (2.9 g/day) or with CVD (2.7 g/day, p = 0.017), and obese participants had higher Na intake (4.2 g/day) than normal/underweight CCSs (2.7 g/day, p<0.001). Daily Na intake was above, and daily K intake below national recommended levels. Adult survivors of childhood cancer need dietary assistance to reduce Na and increase K intake.

Excess salt and inadequate potassium intakes are associated with high cardiovascular disease (CVD). In Montenegro, CVD is the leading cause of death and disability. There is no survey that has directly measured salt and potassium consumption in Montenegro. The aim is to estimate population salt and potassium intakes and explore knowledge, attitudes and behaviour (KAB), amongst the adult population of Podgorica. Random samples of adults were obtained from primary care centres. Participants attended a screening including demographic, anthropometric and physical measurements. Dietary salt and potassium intakes were assessed by 24h urinary sodium (UNa) and potassium (UK) excretions. Creatinine was measured. KAB was collected by questionnaire. Six hundred and thirty-nine (285 men, 25-65 years) were included in the analysis (response rate 63%). Mean UNa was 186.5 (SD 90.3) mmol/day, equivalent to 11.6g of salt/day, and potassium excretion 62.5 (26.2) mmol/day, equivalent to 3.2g/day. Only 7% of them had a salt intake below the WHO recommended target of 5g/day, and 13% ate enough potassium (>90 mmol/day). The majority (86%) knew that high salt causes ill-health. However, only 44% thought it would be useful to reduce consumption. Salt consumption is high, and potassium consumption is low, in men and women living in Podgorica.

Abstract Background: Alcohol consumption is linked to urinary sodium excretion and both of these traits are linked to hypertension and cardiovascular diseases (CVDs). The interplay between alcohol consumption and sodium on hypertension, and cardiovascular diseases (CVDs) is not well-described. Here, we used genetically predicted alcohol consumption and explored relationships between alcohol consumption, urinary sodium, hypertension, and CVDs. Methods: We performed a comparative analysis among 295,189 participants from the prospective cohort of the UK Biobank (baseline data collected between 2006 and 2010). We created a genetic risk score (GRS) using 105 published genetic variants in Europeans that were associated with alcohol consumption. We explored relationships between GRS, alcohol consumption, urinary sodium, blood pressure traits, and incident CVD. We used linear, logistic regression and Cox proportional hazards (PH) models in our analysis. Results: Our analyses supported an interaction effect between alcohol GRS and urinary sodium on hypertension (P interaction =0.03) and CVD (P interaction =0.03). In presence of high urinary sodium excretion, alcohol GRS increases blood pressure in a more enhanced fashion. Conclusions: Our results show that decrease in urinary sodium excretion offsets the risk posed by genetic risk of alcohol consumption.

Inorganic nanoparticles based on magnetite improve the mechanical, thermal, and magnetic properties of microporous cryogel polymer composites. Here we report the synthesis of microporous cryogel based on the crosslinked sodium vinyl sulfonate (Na-VS) and 2-acrylamido-2-methylpropane sulfonic acid sodium salt (Na-AMPS). The magnetite nanoparticles were inserted into Na-VS/Na-AMPS cryogel either during its crosslinking polymerization or by in-situ technique after its crosslinking. The morphology, particle sizes, thermal stability and magnetite contents of Na-VS/Na-AMPS cryogel and its magnetite composites were investigated. The prepared Na-VS/Na-AMPS cryogel and its magnetite composites were used as adsorbents for methylene blue (MB) cationic dye using optimum conditions. The magnetite Na-VS/Na-AMPS cryogel composite prepared by in-situ technique achieved the best adsorption MB removal capacity for 7 cycles among the other adsorbents via chemical adsorption mechanism at room temperature.

The interactions of metal ions with fulvic acids resulted in changes in the particle size and charge. Particle size distribution was trimodal for fulvic acids, bimodal for fulvic complexes with calcium and magnesium, and copper-fulvic complexes had only one size fraction. The compensation of negative charge of carboxylic and phenolic functional groups by positive charged metal ions resulted in the increase in zeta potential which was getting closer to zero in the case of copper-fulvic complexes. However, all metal humic complexes behaved as colloidally unstable which resulted in visually observable sedimentation. Calorimetric measurements provided positive values of changes in enthalpy which indicated endothermic processes. In contrast quantum chemical calculations as well as experiments with model compounds provided negative values indicated exothermic processes. Changes in Gibbs energy were determined as negative and changes in entropy as positive which meant spontaneous processes.

Zirconium dioxide (ZrO2) possesses numerous advantages such as high mechanical strength, low friction coefficient, excellent optical properties, and extended lifespan. Consequently, ZrO2 has a broad research foundation and practical significance in functional films and wear-resistant coatings. However, it suffers from brittleness and low ductility when used as a bio-coating material. In this study, a Ta/ZrO2 film was fabricated on Si (100) and titanium alloy substrates using a magnetron sputtering system, with tantalum (Ta) serving solely as a transition layer. Subsequently, Zr and Nb ions were implanted into the film at varying doses but with consistent energy levels. The analysis focused on the film's microstructure, mechanical properties, hydrophilicity, and corrosion resistance. The results demonstrated a significant improvement in the hydrophilicity and corrosion resistance of the ZrO2 film following the implantation of Zr and Nb ions. First-principles calculations based on density functional theory (DFT) principles indicated that, with increasing doping concentrations of Zr and Nb in the ZrO2 model, the stability of the model increased gradually, thereby enhancing its corrosion resistance.

The removal of metal ions by biosorption on inexpensive materials is still a challenge for environmental engineering research. In this study, marine green algae biomass (Ulva lactuca sp.) and the biochars obtained from this biomass, at 320 C (BC-320) and 550 C (BC-550), were used as biosorbents for the removal of Cu(II) ions from aqueous solution. In addition to comparing the biosorption capacities, the determination of the thermodynamic parameters allows the choice of the most suitable material for the biosorption processes. The experimental results, obtained for Cu(II) ions biosorption on each biosorbent (algae biomass (AB), BC-320 and BC-550), at three different temperatures (10, 30 and 50 C) were analyzed using Langmuir and Freundlich isotherm models, while pseudo-first order, pseudo-second order and intra-particle diffusions models were used to model the kinetic data. The biosorption of Cu(II) ions is best described by the Langmuir model and the pseudo-second kinetic model, regardless of the type of biosorbent. The maximum biosorption capacity (qmax, mg/g) depends on the temperature, but also on the type of biosorbent, and follow the order: BC-320 &lt; AB &lt; BC-550. Using the experimental isotherms, the thermodynamic parameters (G0, H0 and S0) for the biosorption of Cu(II) ions on each biosorbent were calculated. The analysis of the obtained values constitutes the main arguments in choosing BC-550 as the most effective biosorbent for the removal of Cu(II) ions from aqueous media.

The fundamental mechanism underlying negative-ion catalysis involves bond-strength breaking in the transition state (TS). Doubly-charged atomic/molecular anions are proposed as novel dynamic tunable catalysts and demonstrated in water oxidation to peroxide. Density Functional Theory TS calculations have found tunable energy activation barrier reduction ranging from 0.030 eV to 2.070eV, with Si²ˉ, Pu²ˉ, Pa²ˉ and Sn²ˉ the best catalysts; the radioactive elements usher in new application opportunities. C₆₀²ˉ reduces significantly the standard C₆₀ˉ TS energy barrier while graphene increases it, behaving like cationic systems. Rank-ordered catalysts according to their reaction barrier reduction efficiency, variation across charge states and systems reveal their tunable and wide applications, ranging from water purification to biocompatible anti-viral and anti-bacterial sanitation systems.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

Alginate-gelatin hydrogels are extensively used in bioengineering. However, despite different formulations being utilized for growing different cell types in vitro, their pH and its effect, together with the crosslinking ions, of those formulations are still infrequently assessed. In this work we studied how these elements can affect hydrogel stability and printability and influence U2OS and NIH/3T3 cell viability and metabolism on the resulting 3D prints. In this context, 6% alginate + 2% gelatin hydrogels were prepared with 0.1 M MES buffer with pH 5.5, 6.5, 7.0 or 8.0, printed by extrusion-based 3D printing, and crosslinked immediately after printing with either CaCl2 or BaCl2. Our results showed that both the buffer pH and the crosslinking ion (Ca2+ or Ba2+) influence the swelling and degradation rates of the prints. Moreover, the buffer pH influenced the printability of the hydrogel in air, but when printed directly in a fluid-phase CaCl2 or BaCl2 crosslinking bath. In addition, both U2OS and NIH/3T3 cells showed greater cell metabolic activity on one-layer prints crosslinked with Ca2+. Besides, Ba2+ increased cell death of NIH/3T3 cells while had no effect on the U2OS cell viability. The pH of the buffer also caused an important impact on the cell behaviour. U2OS cells showed a 2.25-fold cell metabolism increase on one-layer prints prepared at pH 8.0 in comparison to those prepared at pH 5.5. Whereas, NIH/3T3 cells showed greater metabolism on one-layer prints with pH 7.0. Finally, we observed a difference on cell arrangement of the U2OS cells growing on prints prepared from hydrogels with acidic buffer in comparison to cells growing on those prepared using neutral or basic buffer. These results show that both pH and crosslinking ion influence hydrogel strength and cell behaviour.

Matrix Metaloproteinase-2 (MMP-2) is an extracellular Zn²⁺ protease specific to type I and IV collagens. Its expression is associated with several inflammatory, degenerative, and malignant diseases. Conformational properties, domain movements, and interactions between MMP-2 and its associated metal ions were characterized using a 1.0 µs molecular dynamics simulation. Dihedral principle component analysis revealed 10 families of conformations with the greatest degree of variability occurring in the link region connecting the catalytic and hemopexin domains. Dynamics cross correlation analysis indicated domain movements corresponding to opening and closing of the hemopexin domain in relation to the fibronectin and catalytic domains facilitated by the link region. Interaction energies were calculated using the MMPBSA-interaction entropy analysis method and revealed strong binding energies for the catalytic Zn²⁺ ion 1, Ca²⁺ ion 1, and Ca²⁺ ion 3 with significant conformational stability at the binding sites of Zn²⁺ ion 1 and Ca²⁺ ion 1. Ca²⁺ ion 2 diffuses freely away from its crystallographically defined binding site. Zn²⁺ ion 2 plays a minor role in conformational stability of the catalytic domain while Ca²⁺ ion 3 is strongly attracted to the highly electronegative sidechains of the Asp residues around the central β-sheet core of the hemopexin domain.

The potential of sodium alginate (ALG) and gum arabic (GA) as wall polymers for L-ascorbic acid (AA) encapsulation as a tool for their preservation against the thermo-oxidative degradation was investigated. The influence of such polymers used as wall material on the AA-content, size, encapsulation efficiency, encapsulation yield and thermo-oxidative stability were evaluated. The AA-microparticles were obtained using the spray-drying technique. An experimental Taguchi design was employed to assess the influence of the variables in the encapsulation process. The microparticles morphology and size distribution were characterized by scanning electron microscopy and laser diffraction. The thermal stability of AA microparticles was studied by differential scanning calorimetry and thermogravimetry analysis. This work points out the viability to encapsulate AA using GA and ALG through a spray-drying process. In general, a product yield ranging from 35.1% to 83.2% and an encapsulation efficiency above 90% was reached. Spherical microparticles with a smooth surface were obtained with a mean diameter around 6 μm and 9 μm for the those prepared with GA and ALG, respectively. The thermo-oxidative analysis showed that both polymers allow maintaining AA stable up to 188 °C, which is higher than the traditional processing temperature used in the fish feed industry.

The radiation-induced optical absorption at 1.5-5.5 eV (up to the beginning of fundamental absorption) has been analyzed in CVD diamond disks exposed to 231-MeV 132Xe ions with four fluences from 1012 to 3.81013 cm-2. The 5-mm diameter samples (thickness 0.4 mm) were prepared by Diamond Materials, Freiburg (Germany), average grain size at growth site was around 80 m, the range of xenon ions was R= 11.5 m. The intensity of several bands grows with ion fluence thus confirming radiation-induced origin of the defects responsible for these bands. The recovery of radiation damage has been investigated via isochronal (stepwise) thermal annealing procedure up to 650°C, while all spectra were measured at room temperature. Based on these spectra, the annealing kinetics of several defects, in particular carbon vacancies (GR1 centers with a broad band 2 eV) and complementary C-interstitial-related defects ( 4 eV), as well as vacancies located nearby nitrogen substitutional atoms (narrow bands around 2.5 eV) have been constructed. The experimental kinetics have also been analyzed in terms of the diffusion-controlled bimolecular reactions. The migration energies of tentatively interstitial atoms (mobile components in recombination process) are obtained, their dependence on the irradiation fluences is discussed.

Hypoxia, associated with abnormal vessel growth, is a characteristic feature of many solid tumors that increases their metastatic potential and resistance to radiotherapy. Carbon ion radiation therapy, alone or in combination with other treatments, is one of the most promising treatments for hypoxic tumors because the oxygen enhancement ratio decreases with increasing particle LET. Nevertheless, the current clinical practice does not yet fully benefit from using carbon ions for tackling hypoxia. Here we give an overview of the existing experimental and clinical evidence supporting the efficacy of C-ion radiotherapy in overcoming hypoxia-induced radioresistance, followed by a discussion of the strategies proposed to enhance it, including different approaches to maximize the LET in the tumors.

Within the study, magnetic/polyetherimide-acrylonitrile composite nanofibers membrane with effective adsorption of nickel ions in aqueous solution were established, through a simple electrospinning method. Iron oxide nanoparticles were stirred and ultrasonically dispersed into polyetherimide-acrylonitrile solution for homogenous suspension. Afterwards, the polyetherimide-acrylonitrile solution with uniform suspension of iron nanoparticles was used in electrospinning machine to produce uniform and smooth nanofibers composite membrane. The confirmation of nanoparticles incorporation into polymeric membrane were characterized by SEM, EDX, FTIR, XRD and nanoparticles aqueous stability through leach out test. The high adsorption capability of the composite membranes on nickel ions was mainly attributed to the combination of magnetic nanoparticles, polyetherimide-acrylonitrile matrix and nano-sized structure of membrane. Membrane containing magnetic nanoparticles demonstrate the maximum adsorption capabilities (102 mg/g) for nickel ions from aqueous solution. Different kinetics and isotherm models were applied to understand the adsorption behavior during adsorption process, amongst them pseudo second order kinetic and Langmuir isotherm model were well fitted. Additionally, EDX, FTIR and XRD results confirmed the presence of nickel ions onto membrane after adsorption process. Polyetherimide-acrylonitrile composite nanofibers membranes containing magnetic nanoparticles may use as an environmentally-friendly and non-toxic adsorbent for the removal of nickel ions in aqueous medium due to its ease of preparation, easy to use and stability in aqueous medium by retaining the nanoparticles inside the nanofibers membranes.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

Tungsten is a high-value resource with a wide range of applications. The end-products of tungsten industry are tungsten metal and alloys that are produced through many steps from high-grade concentrates. Pyrometallurgical extraction of tungsten from complex and low-grade ores has great potential to overcome the problems associated with the hydrometallurgical process. In this study, sodium carbonate and silica were used to extract tungsten from wolframite at high temperatures. Sodium tungstate can be obtained directly from the smelting reaction between 1100 and 1300 oC. The smelting slag is further water-leached to recover sodium tungstate in the solution. The effects of Na2CO3/Ore and SiO2/Ore ratios, temperature and reaction time on the recovery of tungstate and the purity of sodium tungstate were systematically studied, which provides a theoretical basis for the pyrometallurgical smelting process of tungsten extraction.

Lanthanum chemical compound incorporates a sensible anionic complexing ability, however lacks stability at low pH scale. Biochar fibers will benefit of their massive space and plethoric useful teams on surface to support metal chemical compound. Herein, wet spinning technology was used to load La3+ onto sodium alginate fiber, and convert La3+ into La2O3 through carbonization. The La2O3 modified biochar (La-BC) fiber was characterized by SEM, XRD and XPS, etc. The adsorption experiment proved that La-BC showed excellent adsorption capacity for chromates, and its saturation adsorption capacity was about 104.93mg/g. The information suggested that the adsorption was in step with both Langmuir and Freundlich model, followed pseudo-second-order surface assimilation mechanics, which instructed that the Cr (VI) adsorption was characterized by single-phase and polyphase adsorption, mainly chemical adsorption. Thermodynamic parameter proved that the adsorption process was spontaneous and endothermic. The mechanistic investigation revealed that the mechanism of adsorption of Cr (VI) by La-BC may include electrostatic interaction, ligand exchange or complexation. Moreover, co-existing anions and regeneration experiments proved that La-BC was recyclable and had a good prospect in the field of chrome-containing wastewater removal.

Addressing the growing need for effective and environmentally friendly fungicides in agricul-ture, this study explored the potential of alginate microparticles loaded with metal ions as a novel approach to combat fungal pathogens. Novel alginate microparticles (microspheres and microcapsules) loaded with zinc or simultaneously with zinc and silver ions were prepared and physicochemically characterized (microparticle size, morphology, topography, encapsulation efficiency, loading capacity, and swelling behavior). Investigation of molecular interactions in microparticles using FTIR-ATR spectroscopy exhibited complex interactions between all con-stituents. Fitting to the simple Korsmeyer-Peppas empirical model revealed the rate-controlling mechanism of zinc and silver ions release from microparticles is Fickian diffusion. Lower values of the release constant k imply a slower release rate of Zn or Ag ions from microcapsules com-pared to that of microspheres. The antimicrobial potential of the new formulations against the fungus Botrytis cinerea was evaluated. When subjected to tests against the fungus, microspheres and microparticles loaded with both zinc and silver ions effectively reduced its growth and al-tered the fungal hyphal structures well as exhibited superior antifungal activity. The results showed the potential of these novel microparticles as potent fungicides in agriculture.

The presence of metal ions, in high concentrations, in the effluents results from industrial metal coating is a well-known fact. Most of time, such metal ions, once they reach the environment, contribute significantly to its degradation. Therefore, it is essential that before such effluents are discharged into the environment, the concentration of metal ions is reduced (as much as possible), to minimize the negative impact on the quality of ecosystems. Among all methods that can be used to reduce the concentration of metal ions, sorption is one of the most viable options, due to its high efficiency and low cost. Moreover, due to the fact that many of the industrial wastes have sorbent properties, this method is in accordance with the principles of circular economy. Based on these considerations, in this study, mustard waste biomass (resulting after oil extraction) was functionalized with an industrial polymeric thiocarbamate (METALSORB), and used as an sorbent to removal Cu(II), Zn(II) and Co(II) ions from aqueous media. The best conditions for the functionalization of mustard waste biomass were found to be: mixing ratio biomass : METASORB = 1g : 1.0 mL and temperature of 30 C. The experimental sorption capacities of functionalized sorbent (MET-MWB) were 0.42 mmol/g for Cu(II), 0.29 mmol/g for Zn(II) and 0.47 mmol/g for Co(II), and were obtained in the following conditions: pH of 5.0, 5.0 g sorbent/L and temperature of 21 C. Modeling of isotherms and kinetic curves, but also the analysis of the results obtained from desorption processes, demonstrates the usefulness of this sorbent in the treatment of effluents contaminated with metal ions. In addition, tests on real wastewater samples highlight the potential of MET-MWB for large-scale applications.

Heavy metal contaminants have serious consequences for the environment and human health. Consequently, effective methods for detecting their presence, particularly in water and food, are urgently required. Accordingly, the present study proposes a sensor for the detection of mercury Hg(II) and lead Pb(II) ions using graphene oxide (GO) as a quenching agent and aptamer solu-tion as a reagent. In the proposed device, the aptamer sequences are labeled by FAM and HEX fluorescent dyes, respectively, and are mixed with 500 ppm GO solution in a microfluidic device. The presence of Hg(II) and Pb(II) ions is then detected by measuring the change in the fluores-cence intensity of the GO/aptamer suspension as the aptamer molecules undergo fluorescence resonance energy transfer (FRET). The experimental results show that the aptamer sensors have a linear range of 10~250 nM (i.e., 2.0~50 ppb) for Hg(II) ions and 10~100 nM (i.e., 2.1~20.7 ppb) for Pb(II) ions. Furthermore, the limit of detection is around 2 ppb for both metals, which is signifi-cantly lower than the maximum limits of 6 ppb and 10 ppb prescribed by the World Health Or-ganization (WHO) for Hg(II) and Pb(II) in drinking water, respectively.

A bacterial strain that could effectively degrade DEHP was isolated from the activated sludge and identified as Bacillus sp. by DNA sequencing. The biochemical degradation pathway of DEHP was further analyzed by GC-MS, and the results showed that DEHP was first decomposed into phthalates (DBP). Diuretic sylycol (DEP) was then generated, and phthalates (PA) were generated by a continuous de-ehelateization reaction. Phthalic acid (PA) was oxidized, dehydrogenated, and decarboxylated into protocatechins. Protocatechins enter the TCA cycle through orthotopic ring opening.　To enhance DEHP degradation, sodium alginate and calcium chloride were used as embedding and cross-linking materials, and the strain was immobilized. The immobilization conditions were optimized via an orthogonal experiment, and the results showed that the optimal immobilization conditions were SA mass fraction of 4%, CaCl2 mass fraction of 5%, ratio of bacteria to SA of 1:1, and the crosslinking time of 6 hours. The immobilized bacteria agent was further applied to MBR systems. The results showed that the removal rate of DEHP (5mg/L) in the system by immobilized bacteria was 91.9%, which is significantly higher than that of free bacteria. The 3, 4-dioxygenase gene and microbial community dynamics were analyzed by q-PCR and Illumina Miseq sequencing. The q-PCR results showed that the number of copies of 3, 4-dioxygenase gene in the immobilized system was significantly higher than that of free bacteria. Illumina Miseq sequencing results showed that Micromonospora, Rhodococcus, Bacteroides and Pseudomonas were the dominant generas in the MBR system. The analysis of bacterial community structure indicated that immobilization technology had a positive impact on the system stability. The results implied that this immobilized technique had potential applications in DEHP wastewater treatment.

In the Republic of Moldova, nearly 90% of all deaths are due to noncommunicable diseases (NCDs), tha majority of which (58%) are caused by cardiovascular disease (CVD). Excess salt (sodium) and inadequate potassium intakes are associated with high CVD. Moreover, salt iodisation is the preferred policy to prevent iodine deficiency and associated disorders. However, there is no survey that has directly measured sodium, potassium and iodine consumption in adults in the Republic of Moldova. The aim is to estimate population sodium, potassium and iodine intakes and explore knowledge, attitudes and behaviour (KAB) towards the use of salt, amongst the adult population in the Republic of Moldova. Proportional random samples of adults were obtained from 28 of the 37 Districts and Municipalities and one Administrative Territorial Unit of Moldova. Participants attended a screening including demographic, anthropometric and physical measurements. Dietary sodium, potassium and iodine intakes were assessed by 24h urinary sodium (UNa), potassium (UK) and iodine (UI) excretions. Creatinine was measured. KAB was collected by questionnaire. Eight hundred and fifty-eight participants (326 men and 532 women, 18–69 years) were included in the analysis (response rate 66%). Mean age was 48.5 yrs (SD 13.8). Mean UNa was 172.7 (79.3) mmoL/day, equivalent to 10.8 g of salt/day and potassium excretion 72.7 (31.5) mmoL/day, equivalent to 3.26 g/day. Men ate more sodium and potassium than women. Only 11.3% of the sample had a salt intake below the World Health Organization (WHO) recommended target of 5 g/day and approximately 39% met WHO targets for potassium excretion (>90 mmoL/day). Whilst 81.7% declared limiting their consumption of processed food and over 70% declared not adding salt at the table, only 8.8% looked at sodium content of food, 31% still added salt when cooking and less than 1% took other measures to control salt consumption. Measures of awareness were significantly more common in urban compared to rural areas. Mean urinary iodine was 225 (SD: 152; median 196) mcg/24h, with no difference between sexes. According to WHO criteria, 41.0% had adequate iodine intake, 28.6% had intake below requirements and 17.8% and 12.6% had above requirement or excessive levels, respectively. Iodine content of salt table was 21.0 (SD: 18.6) mg/kg, with no difference between men and women. However, the content was lower in rural than urban areas (16.7 [SD: 18.6] vs 28.1 [SD: 16.5] mg/kg, p<0.001). There were weak or no correlations between urinary sodium and iodine excretions, and between urinary iodine excretion and iodine concentration in the table salt used in the participants’ households, indicating that in most cases participants were not using iodised salt as their main source of salt, more so in rural areas. In the Republic of Moldova, salt consumption is unequivocally high, potassium consumption is lower than recommended, both in men and in women, whilst iodine intake is still inadequate in 1 in 3 people, although severe iodine deficiency is rare. Salt consumed is often not iodised, with less iodised salt being used in rural areas.

Amplitude growth rates of monochromatic gravity waves were estimated and compared from multiple instrument measurements carried out in Brazil. Wave dynamic parameters were obtained from sodium density profiles from lidar observations carried out in Sao Jose dos Campos (23°S, 46°W), while all-sky images of multiple airglow layers provided amplitudes and parameters of waves over Cachoeira Paulista (23°S, 45°W). Growth rates of gravity wave amplitudes from lidar and airglow imager data were consistent with dissipative wave behavior. Only a small amount of the observed wave events presented freely propagating behavior. Part of the observed waves presented saturated amplitude. The general saturated/damped behavior is consistent with diffusive filtering processes imposing limits to amplitude growth rates of the observed gravity waves.

Salinity substantially affects plant growth and crop productivity worldwide. Plants adopt several biochemical mechanisms including regulation of antioxidant biosynthesis to protect themselves against the toxic effects induced by the stress. One-year-old Pistachio rootstock exhibiting different degrees of salinity tolerance were subjected to sodium chloride induced salt stress to identify genetic diversity among cultivated pistachio rootstock for their antioxidant responses, and to determine the correlation of these enzymes to salinity stress. Leaves and roots were harvested following NaCl-induced stress. Results show that a higher concentration of NaCl treatment induced oxidative stress in the leaf tissue and to a lesser extent in the roots. Both tissues showed an increase in ascorbate peroxidase, superoxide dismutase, catalase, glutathione reductase, peroxidase and malondialdehyde. Responses of antioxidant enzymes were cultivar dependent, as well as temporal and dependent on the salinity level. Linear and quadratic regression model analysis revealed significant correlation of enzyme activities to salinity treatment in both tissues. The variation in salinity tolerance reflected their capabilities in orchestrating antioxidant enzymes at the roots and harmonized across the cell membranes of the leaves. The study provides a better understanding of root and leaf coordination in regulating the antioxidant enzymes to NaCl induced oxidative stress.

For many disciplines of science, all conceivable collisional cross sections and reactions must be precisely known. Although the recent decades were a trial of large-scale research to give these data, many essential atomic and molecular cross section data still missing, and the reliability of the existing cross sections has to be validated. In this paper, we present electron stripping, electron capture, and system breakdown cross sections in carbon (C5+) ions and lithium (Li2+) ions collisions with atomic hydrogen based on the Monte Carlo models of classical and quasi-classical trajectories. According to our expectation, the QCTMC results show higher results in comparison to standard CTMC data, emphasizing the role of Heisenberg correction constraint, especially in the low energy regime. On the Other hand, at high energy, the Heisenberg correction term has less influence as a projectile momentum increase. We present the total cross sections of electron stripping, electron capture, and system breakdown in C5+ ions and Li2+ ions collisions with atomic hydrogen in the impact energy range from 10 keV to 160 keV, which is of interest in astrophysical plasmas, atmospheric sciences, plasma laboratories, and fusion research.

CMC/PVA composite nanofiber membrane was prepared by electrostatic spinning method, using carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) as raw materials and glutaraldehyde as cross-linking agent. The structure, morphology, thermal stability, and filtration performance of CMC/PVA nanofiber membranes were characterized by advanced instrumental analysis methods such as scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, ultraviolet analysis and energy spectrum analysis. The results show that the average fiber diameter decreases from 381 nm to 183 nm, when the spinning voltage is 23 KV and the jet speed is 2 µL/min. The obtained fiber has the smallest particle size and the most uniform distribution. Infrared spectroscopy analysis confirms that the adsorption behavior of nanofiber membranes on Cu2+ and Cr6+ is chemical adsorption. The retention rates of CMC/PVA nanofiber membranes for Cu2+ and Cr6+ reached 97% and 98%, respectively.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

The interaction of solution of poly (diallyldimethylammonium) chloride, PDADMAc and sodium dodecylsulfate, SDS has been studied using conductometric, densimeter and zeta potential methods. the critical micellization concentration (cmc) was determinated with conductance results and increased with the addition of PDADMAc comparing with solutions containing pure SDS. Further the degree of dissociation,  and thermodynamic parameters viz. free energy of micellization, and entropy of micellization, has been evaluated. there results demonstrated that surfactant/polymer complex is governed by both electrostatic and hydrophobic interactions. The apparent molar volume, Vϕ and adiabatic compressibility, Kϕ;s have been determined for the SDS solution from density and speed sound data. the negative charge of the SDS solutions with polymer shows that these complexes probably do not contain surfactant in the form of micelles.

A new and easy-to-make polymer film sensor was prepared by dip-coating technique and this film used as fluorescent chemosensor for the detection of metal ions in aqueous solution. The proposed film sensor exhibited dual emissions at 540 and 582 nm under a single excitation wavelength. The fluorescence behavior of this film sensor toward metal ions has been investigated using these two wavelengths. The proposed sensor was found to show selectivity and sensitive to Fe³⁺ ion when compared the other metal ions in deionized water with excellent photostability. Detection limit of the polymeric film sensor was calculated as 86.15 and 28.90 μM. The results showed that the sensor can be successfully applied to the determination of Fe³⁺ ions in aqueous media. Contact angle measurement of PAZU film probe was also investigated and the result showed that the proposed film probe has hydrophobic property.

This study aimed to investigate the incorporation of micronized salt (MS) to reduce sodium content in fresh sausages while preserving technological, chemical, textural, and sensory characteristics. Four treatments were prepared: control (C) with 2.0% regular salt; M2.0% with 2.0% micronized salt; M1.5% with 1.5% micronized salt; and M1.0% with 1.0% micronized salt. Half of the micronized salt treatment was mixed with the fat during the processing of the fresh sausages. It was possible to achieve a 50% reduction in sodium (M1.0%) in the fresh sausages without negative effects on most technological, chemical, and textural parameters, which did not differ from the control treatment (C). Conversely, "chewiness" decreased in M2.0% compared to the control (C) due to mixing micronized salt with the fat. The sodium reduction did not impact the temporal sensory profile and overall liking. Therefore, using micronized salt in fresh sausages reduces sodium content without affecting sensory traits and product stability.

Hydrogels, soft materials with 3D polymer networks in aqueous solution, have been developed for engineering and bio-related fields. However, these conventional hydrogels are weak and brittle due to lack of energy dissipation mechanisms. Recently, dual-network hydrogels have been proposed, combining rigid and flexible networks and exhibiting high strength, stretchability, and toughness. This paper explores the rheological properties of dual-network hydrogels based on acrylamide and sodium alginate under large deformations. This dual network is a combination of a covalently crosslinked polyacrylamide network and a supramolecular crosslinked sodium alginate network at the presence of divalent calcium cations. Small and large amplitude oscillatory shear methods with Fourier transform rheology, stress decomposition method, and Chebyshev polynomial analysis of large amplitude oscillatory shear (LAOS) data were employed to evaluate non-linearity limit, toughness, and network rigidity. The concentration of calcium ions affects (concentrations 0-80 mg/ml) the nonlinear transition and limit points, and all gel samples exhibit strain hardening, shear thickening, and shear densification.

The nature abundant sodium metal is proposed as ideal anode materials for advanced batteries due to its high specific capacity of 1166mAh g-1 and low redox potential of -2.71V. However, the uncontrollable dendritic Na formation and low coulombic efficiency are still major obstacles for applications. Notably, the unstable and inhomogeneous solid electrolyte interphase (SEI) is recognized to be the root cause. As SEI layer plays a critical role in regulating uniform Na deposition and improving cycling stability, researches on SEI modification, especially the artificial SEI modifications has been extensively investigated recently. In this regard, we discussed the advances on artificial interface engineering from the aspects of inorganic, organic and hybrid inorganic/organic protective layers. Finally, we also highlighted the conclusions and key prospects for further investigations. We hope this review can provide a new insight for sodium metal protection.

Sodium-glucose co-transporter 2 (SGLT2) inhibitors, originally used for diabetes mellitus, are gaining more popularity for other indications owing to their positive cardiovascular and renal effects. Initially, SGLT2 inhibitors were shown to reduce heart failure (HF) hospitalization and improve cardiovascular outcomes in patients with type 2 diabetes. Later, SGLT2 inhibitors were evaluated in patients with HF with reduced ejection fraction (HFREF) and had beneficial effects independent of the presence of diabetes. Recently, reduction in cardiovascular outcomes were also observed in patients with HF with preserved ejection fraction (HFPEF). SGLT2 inhibitors also reduced renal outcomes in patients with chronic kidney disease. Overall, these drugs have an excellent safety profile with a negligible risk of genitourinary tract infections and ketoacidosis. In this review, we discuss the current data regarding SGLT2 inhibitors in special populations including acute myocardial infarction, acute HF, right ventricular (RV) failure, patients with left ventricular assist device (LVAD), and patients with type1 diabetes. We also discuss the potential mechanisms behind the cardiovascular benefits of these drugs.

Ceftiofur (CEF) sodium is a third-generation broad-spectrum cephalosporin commonly used in an extra-label manner in dogs for the treatment of respiratory and urinary system infections. To contribute to the literature supporting CEF use in companion animals, we have developed a compartmental, nonlinear mixed-effects (NLME) model of CEF pharmacokinetics in dogs (PK). We then used the mathematical model to predict (via Monte Carlo simulation) the duration of time for which plasma concentrations of CEF and its pharmacologically active metabolites remained above minimum inhibitory concentrations (respiratory tractEscherichia coli spp). Twelve healthy beagle dogs were administered either 2.2 mg/kg ceftiofur-sodium (CEF-Na) intravenously (I.V) or 2.2 mg/kg CEF-Na subcutaneously (S.C). Plasma samples were collected over a period of 72 hours post-administration. To produce a measurement of total CEF, both CEF and CEF metabolites were derivatized into desfuroylceftiofur acetamide (DCA) before analysis by UPLC-MS/MS. No adverse effects were reported after I.V or S.C dosing. The NLME PK models were parameterized using the stochastic approximation expectation maximization algorithm as implemented in Monolix 2018R2. A two-compartment mamillary model with first-order elimination and first-order S.C absorption best described the available kinetic data. Final parameter estimates indicate that CEF has a low systemic clearance (0.25 L/h/kg) associated with a low global extraction ratio E = 0.02) and a moderate volume of distribution (2.97 L/kg) in dogs. The absolute bioavailability after S.C administration was high (93.7%). Gender was determined to be a significant covariate in explaining the variability of S.C absorption. Our simulations predicted that a dose of 2.2 mg/kg CEF-Na S.C would produce median plasma concentrations of CEF of at least 0.5 µg/mL (MIC₅₀) for approximately 30 hours.

Laser energy per unit surface, necessary to trigger the material removal, decreases with the pulse shortening becoming the pulse-time independent in the sub-picosecond range. These pulses are shorter the electron-to-ion energy transfer time and electronic heat conduction time minimizing the energy losses. The electrons receiving the energy larger than the threshold, drag the ions off the surface in the mode of electrostatic ablation. We show that the pulse shorter than the ion period (Shorter-the-Limit (StL)) ejects conduction electrons with the energy larger than the work function (from a metal) leaving the bare ions immobile in a few atomic layers. The electrons emission is followed by the bare ion’s explosion, ablation, and THz radiation from expanding plasma. We compare this phenomenon to the classic photo effect, nanocluster Coulomb explosions, show differences and consider possibilities for detecting the new mode of ablation experimentally by emitted THz radiation and consider applications of high-precision nano-machining with this low intensity irradiation.

Quaking aspen (Populus tremuloides Michx.) landscapes are valued for their biodiversity, water retention, fire mitigation, aesthetics, and recreation opportunities. Across North America, some aspen populations are experiencing population declines as they face uninhibited ungulate browsing, drought, fire suppression, insects, disease, and inappropriate management. Increased human development and recreational use within aspen landscapes can serve as additive stressors, though there is a dearth of literature examining these elements. At a popular recreational area in Utah, USA, identifying the cause of apparent decline within a larger aspen community is complicated by development upstream and recreation-related activities. We sought to: 1) assess the overall condition of the aspen at the site, 2) understand key variables that influence aspen conditions, and 3) elucidate how aspen fitness varies across the site. We collected data from forty-five plots using established aspen sampling methods, including ungulate presence, tree characteristics, soil chemistry, and environmental descriptors. Results suggest that a combination of higher levels of browsing and elevated soil sodium may be causing premature mortality and limiting aspen recruitment in a portion of the study area. These findings will inform future management at this site, as well as similar recreational forest settings experiencing compound stressors.

Tomato is considered moderately sensitive to salinity, which detracts from the quality and yield of its fruit; therefore, wild populations have been used as a genetic resource. The aim of this research was to identify lines derived from wild tomato populations with tolerance to salinity during the germination and seedling stages. During germination, 52 wild lines and 2 commercial hybrids (Imperial®, Reserva®) were subjected to 150 mM and 0 mM NaCl and evaluated. The test was carried out for 20 days in a germination chamber with constant darkness, temperature of 25±2 °C and relative humidity of 80±4%. At the seedling stage, 22 wild tomato lines with the best performance in the germination test and 2 commercial hybrids (Imperial®, Topanga®) were evaluated for 12 days in a floating raft system. Concentrations of 175 mM and 0 mM NaCl were used. During germination, the saline condition decreased germination percentage (65.2%), speed of germination (88.2%), steam length (72.5%), root length (46.56%), normal plants number (59.5%), stem dry matter (68.78%), root dry matter (61.99%), and total dry matter (67.1%). At the seedling stage, this condition decreased (P<0.05) the aerial part dry matter (46.37%), leaf area (59.35%), root length (42.43%), final plant height (40.24%), and growth rate (71.42%). Seventeen tolerant genotypes were identified at one of both developmental stages, while one genotype showed tolerance at both stages. These results indicate that there are different response mechanisms in each developmental stage. Native tomatoes play an important role in the identification of tolerant genotypes since they can be used as genetic resources for obtaining commercial genotypes with salt tolerance.

Sodium butyrate (NaB) is one of the short-chain fatty acids and is notably produced in large amounts from dietary fiber in the gut. Recent evidence suggests that NaB induces cell proliferation and apoptosis. The skeletal muscle is rich in plenty of mitochondrial. However, it is unclear how NaB acts on host muscle cells and whether it is involved in mitochondria-related functions in myocytes. The present study aimed to investigate the role of NaB treatment on the proliferation, apoptosis, and mitophagy of bovine skeletal muscle satellite cells (BSCs). The results showed that NaB inhibited the proliferation and promoted apoptosis of BSCs, and promoted mitophagy in a time and dose-dependent manner in BSCs. In addition, 1mM NaB increased the mitochondrial ROS level, decreased the mitochondrial membrane potential (MMP), increased the number of autophagic vesicles in mitochondria, and increased the mitochondrial DNA(mtDNA) and ATP level. The effects of the mTOR pathway on BSCs were investigated, and the results showed that 1mM NaB inhibited the mRNA and protein expression of mTOR and genes AKT1, FOXO1, and EIF4EBP1 in the mTOR signaling pathway, while the addition of PP242, an inhibitor of the mTOR signaling pathway, also inhibited mRNA and protein expression levels of mTOR, AKT1, FOXO1, and EIF4EBP1, and promoted mitophagy and apoptosis, which were consistent with the effect of NaB treatment. In conclusion, NaB might promote mitophagy and apoptosis in BSCs by inhibiting the mTOR signaling pathway. Our results would expand the knowledge of sodium butyrate on bovine skeletal muscle cell state and mitochondrial function.

Higher salt (sodium) intake has been associated with a higher blood pressure (BP). The association degree may be influenced by factors such as age, origin and dietary components. This study aimed to evaluate the 24-hours urinary sodium (Na) and potassium (K) excretion in normotensive and hypertensive Dominicans adults and estimate their salt intake. 163 volunteers (18-45, 46-80 years) participated in a cross-sectional study. 24-hours Na and K urinary excretion were measured using an ion selective electrode technique. Na and K urinary excretion (99.4±46.5 and 35.0±17.5 mmol/24h) did not correlated with BP, except in the normotensive group in which K correlated with SBP (0.249, p=0.019). Na and K excretion were similar for normo- and hypertensive subjects. Na-to-K molar ratio (3.1±1.3) was higher in younger subjects (p=0.040). Na-to-K ratio was associated with DBP in the total group (r=0.153, p=0.052), in the hypertensive group (r=0.395, p<0.001) and in the older group with SBP (0.350, p=0.002) and DBP (0.373, p<0.001). In the older group, Na-to-K ratio and DBP correlated after controlling for subjects with hypertension controlled by treatment (r=0.236, p=0.041). The Na-to-K ratio correlated, when salt intake was over 5g/d (52.2%), with SBP (rho=0.219, p=0.044) and DBP (rho=0.259, p=0.017). Determinants of BP were age-dependent and in younger subjects were: sex (SBP, beta: 14.02±2.87, p<0.001) and body mass index (BMI) (beta:-12.07±3.72, p=0.001, beta:9.44±2.87, p=0.001, for SBP and DBP, respectively) and, in the olders, the Na-to-K ratio, for SBP (beta:6.7±2.4, p=0.005) and DBP (beta:3.8±1.1, p<0.001). The mean Na and salt intakes (2.3 and 5.8 g/d) were slightly higher and K intake lower (1.4 g/d) than WHO recommendations.

The stability properties of the Hill equation are discussed, and especially those of the Mathieu equation that characterize ion motion in electrodynamic traps. The solutions of the Mathieu equation for a trapped ion are characterized by using the Floquet theory and Hill's Method solution, which yields an infinite system of linear and homogeneous equations whose coefficients are recursively determined. Stability is discussed for parameters $a$ and $q$ that are real. Characteristic curves are introduced naturally by the Sturm-Liouville problem for the well known even and odd Mathieu equations $ce_m(z,q)$ and $se_m(z,q)$. We illustrate the stability diagram for a combined (Paul and Penning) trap and represent the frontiers of the stability domains for axial and radial motion. In case of a Paul trap the stable solution corresponds to a superposition of harmonic motions. The problem of evaluating the maximum amplitudes of stable oscillations for the ideal conditions (taken into consideration) is also approached. Anharmonic corrections are discussed within the frame of the perturbation theory, while the frontiers of the modified stability domains are determined as a function of the chosen perturbation parameter. The results apply to 2D and 3D ion traps used for different applications in quantum engineering, among which optical clocks, quantum logic and quantum metrology, but not restricted only to these.

Trace metals are essential elements that play key roles in a number of biochemical processes governing human visual physiology in health and disease. Several trace metals, such as zinc, have been shown to play important roles in the visual phototransduction process. In spite of this, there has been little research conducted on the direct effect of trace metal elements on the visual pho-toreceptor rhodopsin. In the current study, we have determined the effect of several metal ions, such as iron, copper, chromium, manganese, and nickel on the conformational stability of rho-dopsin. To this aim, we analyzed, by means of UV-visible and fluorescence spectroscopic methods, the effects of these trace elements on the thermal stability of dark rhodopsin, the stability of its active Metarhodopsin II conformation, and its chromophore regeneration. Our results show that copper prevented rhodopsin regeneration and slowed down the retinal release process after il-lumination. In turn, Fe3+, but not Fe2+, increased the thermal stability of the dark inactive con-formation of rhodopsin, whereas copper ions markedly decreased it. These findings stress the important role of trace metals in retinal physiology at the photoreceptor level, and may be useful for the development of novel therapeutic strategies to treat retinal disease.

The presence of copper in distilled sugar cane spirits, especially cachaça produced in alembics, has impeded the marketing of this product. Red mud (RM) is a residue obtained from alumina production. It contains a high concentration of metal oxides and is very alkaline. The RM was dried at 100 oC and sifted through a 150-micron sieve. The sample was characterized by B.E.T. nitrogen adsorption, scanning electron microscopy-energy-dispersive X-ray (SEM-EDX) and Atomic Absorption Spectrometry (A.A.S.). The textural parameters indicate that the total surface area (S.T.) was 21.9 m2g-1, and the total volume pore (V.T.) was 0.09 cm3g-1. The RM (1 g) was stirred for two hours with a 1.0 L cachaça sample containing 9.39 mg of copper L-1 and filtered under atmospheric pressure. The concentration of copper ions detected in the filtrate was 0.00 mg L-1. No copper ions were retained when the cachaça was filtered through the RM under high pressure without stirring prior to filtration.

The paper discusses the electroreduction of Bi(III) ions in the aspect of expanding the ”cap – pair” effect. The ”cap – pair” rule is associated with the acceleration of the electrode’s processes by organic substances. The interpretation of the ”cap – pair” effect mechanism was expanded to include the effect of supporting electrolyte concentration on the acceleration process and the type of electrochemical active as well as used protonated organic substances. It has also been shown that the phenomena occurring at the electrode/solution interface can influence a change in the dynamics of the electrode’s process according to the ”cap – pair” rule.

Polyethyleneimine (PEI) has been reported to have good potential for the adsorption of metal ions. In this work, PEI was covalently bound to NiFe2O4@SiO2 nanoparticles to form the new adsorbent NiFe2O4@SiO2–PEI. The material allowed magnetic separation and was characterized via powder X-ray diffraction (PXRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier-transform IR spectroscopy (FT-IR), and thermogravimetry-differential thermal analysis (TGA-DTA). The adsorption of CrO42‒, Ni2+, and Pb2+ ions from aqueous solutions was studied at different pH, temperatures, metal ion concentration, and adsorbent dosage. Maximum adsorption capacities of 149.23, 156.68, and 161.25 mg/g were obtained for CrO42‒, Ni2+, and Pb2+, respectively under optimum conditions using 0.075 g of the adsorbent material 250 mg/L ion concentration, at pH = 6.5 and room temperature.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

The hyperactivation of the sympathetic nervous system (SNS) is linked to obesity, hypertension, and type 2 diabetes, with elevated norepinephrine (NE) levels being a key feature. Previous research has shown increased sodium-glucose cotransporter 1 (SGLT1) protein in kidneys of hypertensive rodents, prompting investigation into SGLT1 expression in other tissues such as skeletal muscle. This study aimed to assess: i) whether skeletal muscle cells and tissue express SGLT1 and SGLT2 protein; ii) if NE increases SGLT1 in skeletal muscle cells and iii) whether skeletal muscle of neurogenically hypertensive mice exhibits increased SGLT1 expression. We found that i) skeletal muscle cells and tissue are a novel source of SGLT2 protein and ii) NE significantly elevated SGLT1 in skeletal muscle cells. As SGLT2 inhibition (SGLT2i) with Empagliflozin increased SGLT1, in vivo studies with the dual SGLT1/2i, Sotagliflozin were warranted. Treatment of neurogenically hypertensive mice with Sotagliflozin significantly reduced blood pressure. Our findings suggest that SNS activity upregulates the therapeutic target, SGLT1 in skeletal muscle, potentially worsening cardiometabolic control. As clinical trial data suggests cardiorenal benefits with SGLT2i, future studies should aim to utilize sole SGLT1i which may offer a therapeutic strategy for conditions with heightened SNS activity, such as hypertension, diabetes and obesity.