Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

The battery energy storage systems (BESS) are most promising solution for increasing efficiency and flexibility of distribution networks (DNs) with significant penetration level of photovoltaic (PV) systems. There are various issues related to the optimal operation of DNs with integrated PV sys-tems and BESS that need to be addressed to maximize DN performance. This paper deals with the day-ahead optimal active-reactive power dispatching in unbalanced DNs with integrated sin-gle-phase PV generation and BESSs. The objectives are the minimization of cost for electricity, en-ergy losses in the DN and voltage unbalance at three-phase load buses by optimal managing of active and reactive power flows. To solve this highly constrained nonlinear optimization problem, a hybrid particle swarm optimization with sigmoid-based acceleration coefficients (PSOS) and cha-otic gravitational search algorithm (CGSA), called PSOS-CGSA algorithm, is proposed. A scenario based approach encompassing the Monte Carlo simulation (MCS) method with the simultaneous backward reduction algorithm is used for the probabilistic assessment of the uncertainty of PV generation and power of loads. The effectiveness of the proposed procedure is evaluated through the series test cases in a modified IEEE 13-bus feeder.

Accurately predicting the power of solar power generation can greatly reduce the impact of the randomness and volatility of power generation on the stability of the power grid system, which is beneficial for the balanced operation and optimized dispatch of the power grid system, and reduces operating costs. Solar PV power generation depends on weather conditions, which are prone to large fluctuations under different weather conditions. Its power generation is characterized by randomness, volatility and intermittency. Recently, the demand for further investigation and effective use on the uncertainty of short-term solar PV power generation prediction has been getting increasing attention in many application of renewable energy sources. In order to improve the predictive accuracy of output power of solar PV power generation and develop a precise predictive model, the authors worked predictive algorithms for the output power of a solar PV power generation system. Moreover, since short-term solar PV power forecasting is one of the important aspects for optimizing the operation and control of renewable energy systems and electricity markets, this review focuses on the predictive models of solar PV power generation, which can be verified in the daily planning and operation of a smart grid system. In addition, the predictive methods in the reviewed literature are classified according to the input data source used for accurate predictive models, and the case studies and examples proposed are analyzed in detail. The contributions, advantages and disadvantages of the predictive probabilistic methods are compared. Finally, the future studies of short-term solar PV power forecasting is proposed.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

One of the key areas of the International Renewable Energy Agency’s (IRENA) programme of work is the analysis of renewable technology costs and performance and the dissemination of these results to as wide an audience as possible. In addition to analysis, IRENA seeks to engage a broad range of stakeholders in the context of this work through the Renewable Costing Alliance. The Costing Alliance brings together companies, industry association, governments and researchers to share, confidentially, data for real-world renewable energy project cost and performance, helping to build further on IRENA’s costing work to date. In this context the authors analyse the current cost differentials and cost reduction potentials for solar PV in Japan compared to best practice levels and identify the reasons for higher costs in Japan and how to reduce them. This study analyses the current installed cost differentials for utility-scale, commercial and residential rooftop solar PV systems. In addition to identifying the reasons for the cost differentials, potential policy recommendations to reduce the cost differential are identified.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

In response to the problem of increasing climate change and energy security, investment in renewable energy sources has increased significantly both in Europe and globally. Wind and solar power plants are expected to be the largest contributors to global decarbonization, ranking first and second in projected capacity by 2050. Since all power plants have some impact on the environment, this also applies to photovoltaic power plants. Because of the large capacities projected for PV installed capacity, their environmental impacts should be evaluated. The environmental impacts of PV power plants change over time. Improving the manufacturing technology of PV system components, increasing the efficiency of solar cells, and using materials that are less harmful to the environment will reduce these impacts. Manufacturing PV system components is a highly energy-intensive process that involves greenhouse gas emissions. As new renewable energy capacity is built, the amount of "green" electricity on the grid increases, reducing CO2 emissions per kWh consumed. The objective of this paper is to analyze the current status of the environmental impact of PV power plants under these changing conditions in terms of CO2 emissions, land use, pollutant and noise emissions, and water consumption. The capacity installed to date will reach the end of its lifetime by 2050, which means that the amount of waste associated with it will increase over time. This can have a significant impact on the environment, which is why part of the work is dedicated to this problem. In addition to the available information from the literature, in the part related to land use, the authors also made their own estimates based on data on newly installed PV power plants and PV modules available on the market. The results of the analysis show that there is enough land both in Europe and worldwide to install the planned capacities of rooftop and ground-mounted PV power plants. CO2 emissions are at the same level as for concentrated solar power, with a decreasing trend. Pollutant emissions, noise and water consumption are not a major problem compared to other types of power plants. Overall, it can be concluded that the expansion of PV capacity has a very positive impact on the environment.

Ghana, blessed with abundant solar resources and has strategically invested in solar photovoltaic (PV) technologies to diversify its energy mix and reduce the environmental impacts of traditional energy technologies. The 50 MW solar PV installation by the Bui Power Authority exemplifies the nation's dedication to utilizing clean energy for sustainable growth. This study seeks to close the knowledge gap by providing a detailed analysis of the system's performance under different weather conditions, particularly on days with abundant sunshine and those with cloudy skies. The research consists of one-year monitoring data of the climatic and AC energy output fed into the grid. This data was used to analyze PV performance on each month's sunniest and cloudiest days. The results show that the total amount of AC energy output fed into the grid each month on the sunniest day varies between 229.3 MWh in December and 278.0 MWh in November, while the total amount of AC energy output fed into the grid each month on the cloudiest day varies between16.1 MWh in August and 192.8 MWh in February. Also, the percentage variation in energy produced between the sunniest and cloudiest days within a month ranges from 16.9% (December) to 94.1% (August). The reference and system yield analysis showed that the PV plant has a high conversion efficiency of 91.3%; however, only the sunniest and overcast days had an efficiency of 38% and 92%, respectively. The BPA plant's performance can be enhanced by using this analysis to identify erratic power generation on sunny days and schedule timely maintenance to keep the plant's performance from deteriorating. Optimizing a solar PV system's design, installation, and operation can significantly improve its AC energy output, performance ratio, and capacity factor on sunny and cloudy days.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Based on collected power generation data associated with solar irradiance, PV system conversion efficiency and cell temperature, an hourly solar PV power estimation model by a parallel artificial neural network (ANN) and particle swarm optimization (PSO) algorithm is proposed. Weight matrices related to different seasons and geographic areas for estimation power generations have been trained by real measured operation data. The parallel PSO algorithm with heuristic global optimization technique assists the ANN training process to get near optimal solutions precisely. The accuracy and reliability of estimation is audited by actual details of photovoltaic power stations in various regions and scales. The results of estimation model can not only assist the electricity dispatcher to explicitly monitor the trend of solar power generation in different areas, but also coordinate with traditional power plants to meet load demand more accurately. The presented model will bring benefits to power dispatching for larger scales of intermittent and unstable solar power generation.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

Due to the high solar irradiance or energy price, certain regions in the U.S. may reach 100% PV penetration and experience degradation of frequency response greater than the interconnection as a whole. Therefore, in this section, the 100% PV penetration region in each interconnection is simulated to study the local high PV penetration effects. The study was performed by quantifying RoCoF, frequency nadir, and settling frequency at different regional PV penetration levels. The impact of high regional PV penetration on the compliance of grid code on frequency response is also studied.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

The present study aims at investigating the relationship between Initial Public Offerings (IPOs) variables mainly underpricing on one hand, and the brand value measures on the other. Our final data set is 104 international brand companies. We implement empirical approach using hierarchical OLS regression and descriptive statistics. We show that underpricing is positively related to brand value which emphasizes the marketing role of going public and underpricing in enhancing brand equity through the product market, which additionally confirms some information asymmetry models. We also find that on average brand companies had not been recognized as brands at the IPO time. Moreover, we show the positive role of private equity in enhancing brand value, additionally, the non-linear association between underpricing and brand value is not evident. Finally, we draw some policy implication and suggestions for future research.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

The assessment of Photovoltaic (PV) systems, a key component of sustainable energy solutions, is of paramount importance in the pursuit of a greener future. This abstract provides an overview of environmental assessments associated with PV systems, considering their life cycle, energy production, and ecological impact. The study explores various methodologies and tools employed in the evaluation of PV systems’ environmental performance, addressing issues such as material sourcing, manufacturing, installation, and end-of-life disposal. Additionally, it delves into the trade-offs and challenges in achieving sustainability objectives in the solar energy sector. By critically examining the environmental implications of PV systems, this research contributes to informed decision-making and the sustainable integration of solar power into our energy landscape.

Taking a socio-technical perspective, I focus on solar businesses (niche market actors) in Iran. As one of the key stakeholder groups whose business prosperity is tied to the development of solar PV, they play a crucial role in accelerating the energy transition. Given the incumbent fossil-based electricity sector in Iran and the least enabling policies, I am first interested to find (i) the main drivers and barriers of solar businesses; and (ii) the roles these solar businesses play in bringing solar PV deployment forward in Iran. I collected the data via 20 semi-structured interviews with solar businesses in Golestan, Guilan, Tehran, Khorasan Razavi, and Eastern Azerbaijan Provinces in Iran. Taking an inductive approach, I considered sustainability transition and social acceptance theories as sensitising concepts to investigate common and specific points of solar business acceptance in Iran. I find ecological awareness, belief in intergenerational justice, and willingness to innovate, as the main intrinsic drivers and socioeconomic opportunity and tackling the energy imbalance as extrinsic drivers; while the lack of a common vision with the energy governors, and the low knowledge of solar PV among the customers, escalating prices, and challenges to accessing good quality solar equipment are the most prior obstacles. Moreover, I understand educating people, driving the innovative deployment of solar PV, and facilitating the diffusion of it, as the major roles of solar businesses in Iran. I find that the sustainability transition literature overlooked the key role of solar businesses specially in fossil-based and developing economies. My findings suggest that the positive intrinsic mechanisms among the solar businesses, in combination with better-enabling policy frameworks and external factors, like lifting the sanctions and joining the global energy market, climate change mitigation commitments and standards, can help solar businesspeople to lead and accelerate solar PV development in Iran.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

The paper examines design and operating data of current concentrated solar power (CSP) solar tower (ST) plants. The study includes CSP with or without boost by combustion of natural gas (NG), and with or without thermal energy storage (TES). The latest, actual specific costs per installed capacity are very high, 6085 $/kW for Ivanpah Solar Electric Generating System (ISEGS) with no TES, and 9227 $/kW for Crescent Dunes with TES. The actual production of electricity is very low and much less than the expected. The actual capacity factors are 22% for ISEGS, despite combustion of a significant amount of NG largely exceeding the planned values, and 13% for Crescent Dunes. The design values were 33% and 52%. The study then reviews the proposed technology updates to produce better ratio of solar field power to electric power, better capacity factor, better matching of production and demand, lower plant’s cost, improved reliability and increased life span of plant’s components. The key areas of progress are found in materials and manufacturing processes, design of solar field and receiver, receiver and power block fluids, power cycle parameters, optimal management of daily and seasonal operation of the plant, new TES concepts, integration of solar plant with thermal desalination, integration of solar plant with combined cycle gas turbine (CCGT) installations and finally, specialization and regionalization of the project specification.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

This paper studied the solar PV frequency control in the U.S. Eastern Interconnection (EI) and Texas Interconnection (ERCOT) systems. The studied frequency control approaches include droop frequency control, inertia control, and droop-inertia-combined frequency control. The control effects of different frequency controls of PV in the EI and ERCOT are studied using actual high PV penetration interconnection grid models to provide suggestions to the future revision of future PV frequency control standards.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Wood-borer extermination by a dry heat clean-up is the essential method from the point of view of sustainability of historical wooden structures like trusses and ceilings in heritage-listed buildings. The wooden components are heated by a hot air of temperature about 100°C until the temperature in the centre of the wooden structures reaches 55°C to kill the wood-borers. In this article we review the method and present solution of the heat equation for structural wooden components. We also suggest an approximate formula that enables to estimate the necessary heating time for different cross sections of wooden components and can be used in technical application of the method.

In this study an adjusting post-processing approach is implemented for improving intra-hourly forecasts of solar power and ramp events of PV solar power systems at different locations in the United States. This study also serves as an out-of-sample test to evaluate the performance of the adjusting approach with different locations and timescales. Thus, various individual intra-hourly forecasts of solar power are combined and adjusted by applying the adjusting approach. Both point and probabilistic forecasts of solar power are included. After that, solar power ramp event forecasting by the adjusting approach is carried out.

This paper focuses on designing and assessing Pumped Hydroelectric Energy Storage Systems (PHES), connected to the grid and PV system for self-consumption structured at Mutah university in an area of high solar potential. In focusing on PHES and PV literature was made to have data on the field, based on the grid code needed in Jordan. Next, a prospection to find the proper location for the installation was done. Afterward, a load profile was inserted to know the energy demand of the university. Then The productivity of the solar power plant of Mutah University was included. Finally, MATLAB software was used to realize the amount of energy to be stored, this data was used to implement the system which was chosen and sized. PHES layout was created to find the most accurate values for parameters to optimize the system performance, and to investigate the loss analysis. The system attains 9230.89 MWh/year. An annual load yields 4430 MWh/year, which covers the Mutah university demand with an estimated saving of 2039773 JD.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

In this paper a novel and flexible solution for fault prediction based on data collected from Supervisory Control and Data Acquisition (SCADA) system is presented. Generic fault/status prediction is offered by means of a data driven approach based on a self-organizing map (SOM)and the definition of an original Key Performance Indicator (KPI). The model has been assessed on a park of three photovoltaic (PV) plants with installed capacity up to 10 MW, and on more than sixty inverter modules of three different technology brands. The results indicate that the proposed method is effective in predicting incipient generic faults in average up to 7 days in advance with true positives rate up to 95%. The model is easily deployable for on-line monitoring of anomalies on new PV plants and technologies, requiring only the availability of historical SCADA data, fault taxonomy and inverter electrical datasheet.

One of the most crucial and economically beneficial tasks for energy customer is peak load curtailment. On account of the fast response of renewable energy resources (RERs) such as photovoltaic (PV) units and battery energy storage system (BESS), this task is closer to be efficiently implemented. Depends on the customer peak load demand and energy characteristics, the feasibility of this strategy may warry. When adaptive neuro-fuzzy inference system (ANFIS) is exploited for forecasting, it can provide many benefits to address the above-mentioned issues and facilitate its easy implementation, with short calculating time and re-trainability. This paper introduces a data driven forecasting method based on fuzzy logic for optimized peak load reduction. First, the amount of energy generated by PV is forecasted using ANFIS which conducts output trend, and then, the BESS capacity is calculated according to the forecasted results. The trend of the load power is then decomposed in Cartesian plane into two parts, left and right from load peak, searching for BESS capacity equal. Network switching sequence over consumption is provided by a fuzzy logic controller (FLC) with respect to BESS capacity and PV energy output. Finally, to prove the effectiveness of the proposed ANFIS-based peak shaving method, offline digital time-domain simulations have been performed on a real-life practical test micro grid system in MATLAB/Simulink environment and the results have been experimentally verified by testing on a practical micro grid system with real-life data obtained from smart meter and also, compared with several previously-reported methods.

In this paper, a method of charging lead acid battery with solar power by flyback converter is proposed. The basic system consists of a buffer circuit, auxiliary power circuit, control circuit, voltage feedback circuit and current feedback circuit. The system is capable of monitoring battery voltage and the current, charging the coupling inductor and automatic control of output duty cycle, overcharging and over-discharging protection. The experiment proves that the charging efficiency is improved by about 83% at full load.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Photovoltaic(PV) power generation is highly nonlinear and stochastic. Accurate prediction of PV power generation plays a crucial role in grid connection as well as the operation and scheduling of power plants. To predict the PV power combination model, this paper suggests a method based on Empirical Mode Decomposition (EMD), Ensemble Empirical Mode Decomposition (EEMD), Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN), Nonlinear Auto-Regressive Neural Networks with Exogenous Input (NARXNN), Long Short Term Memory (LSTM) Neural Network, and Light Gradient Boosting Machine (LightGBM) algorithms. To attempt to reduce the non-smoothness of PV power, the weather variable features with the greatest effect on PV power are first identified by correlation analysis. Following this, the PV power modal decomposition is split and reorganized into a new feature matrix. Finally， a NARX is used to obtain preliminary PV power components and residual vector features， and the PV power is predicted by combining three models of LightGBM， LSTM, and NARX and then the final prediction results are obtained by combining the PV power prediction results using error inverse method weighted optimization. The prediction results demonstrate that the model put forth in this paper outperforms those of other models and validate the model's validity by utilizing real measurement data from Andre Agassi College in the United States.

In this paper, a study of modeling PV cell (solar cell), PV module (solar modules) and PV array solar array) using Matlab/Simulink software is presented. This study is focused on the study to design photovoltaic cell, photovoltaic modules, photovoltaic panels and PV array (solar array) and to analyze the change in PV performance according to changes in different parameters such temperature, solar irradiation, reverse saturation current, series resistance and shunt resistance. This study shows the PV and IV characteristics curve for each model from which MPP (maximum power point) is determined. In this study, different PV and IV characteristic curves are gained for varying temperatures with specified solar irradiation conditions,s and then the MPP is tracked. The highest power output is also compared between the designed PV module and the selected PV module (MX Solar USA MX60-245)

The solar heat pump system based on photovoltaic photothermal (PV/T) modules is a new technology that integrates photovoltaics and heat reutilization. It can improve the efficiency of photovoltaic conversion and recovery the remaining heat generated during the photoelectric conversion process, thereby improving the comprehensive efficiency of the whole system. Simulink software is a visual simulation tool, which has the advantages of strong applicability, clear simulation structure and calculation process. The design of its graphical programming greatly simplifies the user modeling process and allows for direct viewing of results, therefore improving the simulation efficiency. At present, there is little research on simulation of solar heat pump systems with PV/T modules based on Simulink software. In this paper, the mathematical models of each component contained in the PV/T solar heat pump system were established based on the system working principle, energy conservation equations and some empirical formulas, and then the operation of the system was simulated by the Simulink software. Due to the operation characteristic of PV/T modules is the key influencing factor for the whole system performance, the model and simulation process for PV/T modules were introduced in detail. The results showed that the surface temperature of PV/T modules under different operating conditions was significantly lower than that of ordinary photovoltaic panels, and the temperature change amplitude was lower. As results, the power generation and photovoltaic conversion efficiency were significantly improved.

Nearly Zero Energy Buildings (NZEBs) play a key role in the world energy transition and this is motivating the scientific community to develop innovative electrical and thermal systems, characterized by very high efficiency to specifically address the energy needs of modern buildings. Naturally, the integration on buildings of latest generation PV-systems helps to satisfy this need and, having in mind this objective, an innovative and highly efficient BIPV-system is presented and discussed in this paper. First, the proposed PV-system is purpose-built to be fully integrated into a variety of buildings and, preferably, into their rooftop. It is based on a certain number of innovative rotating and bifacial PV-modules which are specifically made to be installed “under-glass”, within a likewise custom-made transparent casing. Each of the aforementioned PV-module has the form of single row of bifacial PV-cells and is equipped with two special terminations; the PV-modules are then installed inside their transparent casing, side by side and suitably spaced from each other. Thanks to the aforementioned properties, the PV-modules can rotate around their central longitudinal axis, by using a very low-power, reliable and efficient mono-axial solar tracking system. Finally, by the aforementioned way, the proposed PV-system assumes – de facto - the form of a transparent BIPV-generator (PV-skylight), equipped with an innovative “under-glass” single axis solar tracking system. Once the proposed PV-generator is fully integrated into a building, it generates electricity and, additionally, helps to improve both the whole energy performances and the aesthetic appearance of the building. The electricity generation and illuminance performances of the proposed BIPV-generator are experimentally tested by using a low-power home-made prototype driven by different solar tracking logics and under different operating conditions; the most relevant results are summarized and extensively discussed.

Fourteen (14) rack-mounted polycrystalline modules installed on the concrete roof of the solar energy applications laboratory at the Kwame Nkrumah University of Science and Technology (KNUST) in Ghana, a hot humid environment were assessed after 19 years of continuous outdoor expodure. The physical state of the modules was documented using a visual inspection checklist. They were further assessed by current-voltage (I-V) characterization and thermal imaging. The modules were found to be in good physical state, except some bubbles on front side and minor discolouration/corrosion at edge of the cells. Compared with reference values, the performance decline of the modules observed over the exposure period was: nominal power (P_nom), 21% to 35%; short circuit current (I_sc), 5.8% to 11.7%; open circuit voltage (V_oc) 3.6% to 5.6% and 11.9% to 25.7% for fill factor (FF). It is hoped that this study will provide some helpful information to project developers, manufacturers and the research community on the long-term performance of PV modules in Ghana.

There are ~200.000 households living in the detached houses and ger (yurt) with the small-coal stove which burns a raw coal in the Ulaanbaatar city. The proper heating system and improvement on the energy efficiency of residential dwellings is vital important for Ulaanbaatar city to reduce an air pollution as well as for the operation of current central energy system. This study shows the experimental results of two Gers with two different heating system and different thermal insulation. Technical availability of the system consisting of ETS heater with daytime charging schedule and areal PV system is also examined by using a simulation of MATLAB programming. As a result of the experiment, the indoor comfort level and energy efficiency of the Ger with added insulation and ETS heater with nighttime charging was enhanced to compare with the reference Ger. The Ger with added insulation and ETS heater consumed 3169 kWh for electric appliances and 5989 kWh for the heating season. The simulation was resulted that the ETS heater to be installed in the Ger 2 had prospected to increase the PV self-consumption rate by 76% because of the daytime charging schedule of ETS heater. The PV system supplied 31% of the total energy consumption with remained 69% of the main grid.

This paper deals with the problem of determining the optimal capacity of Concentrated Solar Power (CSP) plants, especially in the context of hybrid solar power plants. This work presents an innovative analytical approach to optimize the capacity of concentrated solar plants. The proposed method is based on the use of additional non-dimensional parameters, in particular the design factor and the solar multiple factor. The paper presents a mathematical optimization model that focuses on the capacity of concentrated solar power plants where thermal storage plays a key role in the energy source. The analytical approach provides a more complete understanding of the design process for hybrid power plants. In addition, the use of additional factors and the combination of the proposed method with existing numerical methods allows for a more refined optimization, which allows for a more accurate selection of the capacity for specific geographical conditions. Importantly, the proposed method significantly increases the speed of computation compared to traditional numerical methods. Finally, the authors present the results of the analysis of the proposed system of equations for calculating the levelized cost of electricity (LCOE) for hybrid solar power plants. The nonlinearity of the LCOE on the main calculation parameters is shown.

We introduce firm solar forecasts as a strategy to operate optimally overbuilt solar power plants in conjunction with optimally sized storage systems so as to make up for any power prediction errors, hence entirely remove load balancing uncertainty emanating from grid-connected solar fleets. A central part of this strategy is plant overbuilding that we term implicit storage. We show that strategy, while economically justifiable on its own account, is an effective entry step to least-cost ultra-high solar penetration where firm power generation will be a prerequisite. We demonstrate that in absence of an implicit storage strategy, ultra-high solar penetration would be vastly more expensive. Using the New York Independent System Operator (NYISO) as a case study, we determine current and future cost of firm forecasts for a comprehensive set of scenarios in each ISO electrical region, comparing centralized vs. decentralized production and assessing load flexibility’s impact. We simulate the growth of the strategy from firm forecast to firm power generation. We conclude that ultra-high solar penetration enabled by the present strategy, whereby solar would firmly supply the entire NYISO load, could be achieved locally at electricity production costs comparable to current NYISO wholesale market prices.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

A novel hybrid CSP-PV power plant is presented. Instead of the integration used in current hybrid power plants, where part of the PV production is charged into the thermal energy storage system through electrical resistors, the proposed system integrates both PV and thermal solar fields using a high-temperature heat pump. Both the heat pump and the heat engine are based on Brayton supercritical CO2 thermodynamic cycles. Such integration allows for charging the molten salts storage as if a central tower receiver field supplied the thermal energy, whereas parabolic trough collectors are employed. Unlike conventional hybrid plants, where the storage of PV production leads to a decrease in power injected into the grid throughout the day, the power injected by the proposed system remains constant. The heat engine efficiency is 44.4%, and the COP is 2.32. The LCOE for a 50 MWe plant with up to 12 hours of storage capacity is 171 $/MWh, which is lower than that of existing CSP power plants with comparable performance. Although the cost is higher compared to a PV plant with batteries, this hybrid system offers two significant advantages: it eliminates the consumption of critical raw materials in batteries, and all the electricity produced comes from a synchronous machine.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

Solar photovoltaic systems (PVs) are becoming more popular in Poland, as the country aims to increase its share of renewable energy sources and reduce its dependence on coal. According to the official data the total installed PV capacity in Poland reached 15.6 GW in September 2023 while at the end of 2020 it was 4.1 GW. This situation was caused by many factors, but mainly by government subsidy programs for households and rising electricity prices. A number of photovoltaic installations with a capacity of up to 50 kWp were carried out, although the installation should always be adapted to the needs of a given household. Estimating the yield of solar energy systems is crucial for that. It can be done by several methods, but always as initial step in modelling of solar energy systems weather data, especially solar irradiation is required. To get this data we can arrange the measurement from ground stations or use reanalysis models and satellite-derived datasets. There are several different datasets, both public and commercial, of solar irradiance data ready to use. This data provides insights into the average solar irradiance levels throughout the year, aiding in estimating the energy generation capacity. The paper contributes the knowledge of energy generation capacity that can be quickly counted for a solar PV micro-system with different orientation and inclination as a multiplier of the energy value obtained from a solar PV system of 1 kW-peak for a significant number of locations in Poland based on open-source solar irradiation data

This paper presents a microgrid distributed energy resources (DERs) for a rural standalone system. It is made up of solar photovoltaic (solar PV) system, battery energy storage system (BESS), and wind turbine coupled to permanent magnet synchronous generator (WT-PMSG). The DERs are controlled by maximum power point tracking (MPPT) based proportional intergral (PI) controllers for both maximum power tracking and error feedback compensation. The MPPT uses the perturb and observe (P&O) algorithm for tracking the maximum power point of the DERs. The PI gains are tuned using the Ziegler-Nichol’s method. The developed system was built and simulated in MATLAB/Simulink under two conditions - constant load, and step load changes. The controllers enabled the BESS to charge even during conditions of varying load and other environmental factors such as change of irradiance and wind speed. The reference was tracked very well by the output voltage of the DC grid. This is a useful research for electrifying the rural islanded areas, too far from the grid.

Access to reliable, clean, modern cooking enhances life chances. One option is photovoltaic cooking systems. Accurate solar data is needed to ascertain to what extent these can satisfy the needs of local people. This paper investigates how to choose the most accurate satellite derived solar irradiance database for use in Africa. This is necessary because there is a general shortage of ground measurements for Africa. The solar data is needed to model the output of solar cooking systems, for instance, a solar panel, battery and electric pressure cooker. Four easily accessible satellite databases are validated against ground measurements using a range of statistical tests. Results demonstrate the impact of the mathematical measure used and the phenomenon of balancing errors. Fitting of the satellite model to appropriate climate zone and/or nearby measurements improves accuracy, as does higher spatial and temporal resolution of input parameters. That said, all the four databases reviewed were found to be suitable for simulating PV yield in East Africa.

This paper provides a study on the development of solar energy, its prospects, and its impacts in Africa. Although the main focus is on technologies adopted for different uses (solar farms, mini-grids, off-grid, solar houses, irrigation, lighting, etc.), we also consider some aspects that increase the adoption of solar energy, such as legislation and business models. Finally, we will examine current and future solar projects managed by NGOs and international companies and how they benefit to leveraging social and economic standards, quality of life as well as capacity building in Africa. This study shows the plethoric interest of institutions outside Africa in the market of solar energy in the continent and that there is no African strategy to increase its independency toward a sustainable development particularly through energy transition.

The rapid industrial growth in solar energy is gaining increasing interest in renewable power from smart grids and plants. Anomaly detection in photovoltaic (PV) systems is a demanding task. In this sense, it is vital to utilize recent advances in machine learning to accurately and timely detect different anomalies and condition monitoring. This paper addresses this issue by evaluating different machine learning techniques and schemes and showing how to apply these approaches to solve anomaly detection and detect faults on photovoltaic components. For this, we apply distinct state-of-the-art machine learning techniques (AutoEncoder Long Short-Term Memory (AE-LSTM), Facebook-Prophet, and Isolation Forest) to detect faults/anomalies and evaluate their performance. These models shall identify the PV system's healthy and abnormal actual behaviors. Our results provide clear insights to make an informed decision, especially with experimental trade-offs for such complex solution space.

Supermarkets in Port Harcourt (PH) city, Nigeria, predominantly rely on diesel electricity generation due to grid instability, leading to high cost of electricity prices. Although solar photovoltaic (PV) systems have been proposed as an alternative, these supermarkets have yet to adopt them, mainly due to high investment costs and a lack of awareness of the long-term financial and environmental benefits. This paper examines the technical and economic practicality of a PV system for these supermarkets using the PVsyst software and a spreadsheet model. Solar resources showed that PH has a daily average solar radiation and temperature of 4.21 kWh/m2/day and 25.73℃, respectively. Market Square, the supermarket with the highest peak power demand of 59.8 kW, and a 561 kWh/day load profile, was chosen as a case study. A proposed PV system with a power capacity of 232 kW, battery storage capacity of 34,021 Ah, a charge controller size of 100 A/560V, and an inverter with a power rating of 60V/75 kW has been designed to meet the load demand. The economic analysis showed a $266,936 life cycle cost, $0.12 per kWh levelized cost of electricity (LCOE), 4-year simple payback time, and a 20.5% internal rate of return (IRR). The PV system is feasible due to its positive net present value (NPV) of $165,322 and carbon savings of 582 tCO2/year.

The paper concludes that the choice of charging strategy depends on the specific requirements and limitations of the off-grid solar PV system, and that a careful analysis of the factors that affect performance is necessary to identify the most appropriate approach. Also provides valuable insights for designing and optimizing off-grid solar PV systems, which can help to improve the efficiency, reliability, and cost-effectiveness of these systems.

The accurate prediction of heat load profiles with a daily resolution is required for a broad range of applications such as potential studies, design, or predictive operation of heating systems. If the heat demand of a consumer is mainly caused by (production) processes independent of the ambient temperature, existing load profile prediction methods fail. To close this gap, this study develops two ex post machine learning models for the prediction of the heat demand with a daily resolution. The selected input features are commonly available to each consumer connected to public natural gas and electricity grids or operating an energy monitoring system: Ambient temperature, weekday, electricity consumption, and heat consumption of the last seven days directly before the predicted day. The study’s database covers electricity and natural gas consumption load profiles from 82 German consumers over a period of two years. Electricity and heat consumption correlate strongly with individual patterns for many consumers. Both, shallow and deep learning algorithms are evaluated. The highest accuracy is achieved by a Long Short Term Memory (LSTM) model with a median of R² of 0.94. The ex post model architecture makes the model suitable for automated anomaly detection in energy monitoring systems.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

One of the major problem of photovoltaic grid integration is limiting the solar-induced imbalances since these can undermine the security and stability of the electrical system. Improving the forecast accuracy of photovoltaic generation is becoming essential to allow a massive solar penetration. In particular, improving the forecast accuracy of large solar farms generation is important both for the producers/traders to minimize the imbalance costs and for the Transmission System Operators to insure stability. In this article, we provide a benchmark for the day-ahead forecast accuracy of utility scale PV plants in 1325 locations spanning the country of Italy. We then use these benchmarked forecasts and real energy prices to compute the economic value of forecast accuracy and accuracy improvement in the context of the Italian energy market regulatory framework. Through this study, we further point out some several important criticisms of the Italian “single pricing” system that brings to paradoxical and counterproductive effects regarding the need to reduce the imbalance volumes. Finally, we propose a new market-pricing rule and innovative actions to overcome these undesired effects of the current dispatching regulations.

We conducted this systematic review with the objective to understand the efficacy and safety of proton pump inhibitors [PPIs] in the pediatric population. We have used PubMed to identify randomized controlled trials [RCTs] published between 1st June 2010 and 30th June 2023, in patients from birth to 18 years old, with gastroesophageal reflux disease [GERD], who received treatment with any PPI. The literature yielded 76 articles and 13 met inclusion criteria. For infants, PPIs were equal to placebo in reducing GERD symptoms in 4 articles. In 1, the number of GER episodes and esophageal acid exposure were lower in infants who received PPIs and left lateral position, but there was no significant improvement in symptoms. In another publication, the combination of PPIs and feeding modifications [FM] was not more effective than PPIs alone. For children and adolescents, PPIs were effective in improving symptoms and achieving mucosal and histological healing, which was subsequently maintained. To conclude, PPIs are not effective to reduce symptoms related to GERD in infants, but are effective in older children, along with histological remission. Generally, PPIs are well tolerated, but it is important to not forget the possible adverse events [AE], especially if they are used for a long time.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

Because of the rapid advancement in the use of photovoltaic (PV) energy systems, it has become critical to look for ways to improve the energy generated by them. The extracted power from the PV modules is proportional to the output voltage. The relationship between output power and array voltage has only one peak under uniform irradiance, whereas it has multiple peaks under partial shade circumstances (PSC). There is only one global peak (GP) and many local peaks (LPs), where the typical maximum power point trackers (MPPT) may become locked in one of the LPs, significantly reducing the PV system's generated power and efficiency. The metaheuristic optimization algorithms (MOAs) solved this problem, albeit at the expense of the convergence time, which is one of these algorithms' key shortcomings. Most MOAs attempt to lower the convergence time at the cost of the failure rate and the accuracy of the findings because these two factors are interdependent. To address these issues, this work introduces the dandelion optimization algorithm (DOA), a novel optimization algorithm. The DOA's convergence time and failure rate are compared to other modern MOAs in critical scenarios of partial shade PV systems to demonstrate the DOA's superiority. The results obtained from this study showed substantial performance improvement compared to other MOAs, where the convergence time is reduced to 0.4 s with zero failure rate compared to 0.9 s, 1.25 s, and 0.43 s for other MOAs under study. The optimal number of search agents in the swarm, optimal initialization of search agents, and optimal design of the dc-dc converter is introduced for optimal MPPT performance.

Grid energy storage system for PV Applications is connected with three different power sources i.e. PV Array, Battery and the Grid. It is advisable to have Isolation between these three different sources to provide safety for the equipment. The configuration proposed in this paper provides the complete isolation between the three sources. A Power Balancing Control (PBC) for this configuration is proposed to operate the system in three different modes of operation. Control of a dual active bridge (DAB) based battery charger which provides a galvanic isolation between batteries and other sources is explained briefly. Various modes of operation of a Grid energy storage system are also presented in this paper. Hardware-In-Loop (HIL) Simulation is carried out to check the performance of the system and the PBC algorithm. Power circuit (comprises of inverter, dual active bridge based battery charger, grid, PV cell, batteries, contactors and switches) is simulated and the controller hardware and user interface panel are connected as HIL with the simulated power circuit through Real Time Digital Simulator (RTDS). HIL simulation results are presented to explain the control operation, steady state performance in different modes of operation and the dynamic response of the system.

Photovoltaic modules should pass series of tests and examinations, verifying the electrical and thermal characteristics of the module, before being released to the market, examining the properties of the modules should undergo appropriate durability and efficiency tests under real outdoor conditions with exposure to climatic conditions and under laboratory conditions. The performance of photovoltaic cells depends on many factors, such as solar irradiance, module operating temperature, installation location, weather conditions and module shading. In this paper, three selected photovoltaic modules were examined using a large-scale steady-state solar simulator. The current-voltage (I-V) characteristics of the photovoltaic modules were experimentally tested and analyzed. The next step was to implement a three-layer artificial neural network model (MLP). The experimental data obtained in the previous step coupled with output data from MLP were then used in global sensitivity analysis (GSA). Experiments carried out on a large-scale stationary solar simulator showed differences between the values declared by the manufacturer and the values obtained from measurements of PV modules. The first module tested achieved the maximum power point greater than that specified by the manufacturer, while the other two showed power drops; it was 85-87% for the second module, and 95-98% for the third, respectively. The performed global sensitivity analysis (GSA) for the MLP model showed that the parameters: eff (22.9) and Voc/V (14.19) have the largest effect on the power-voltage relationship, while U (7.29) has the smallest effect. The usefulness of machine learning (ML) methods in the comparative analysis of PV modules has been proved.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Load Frequency Control (LFC) is essential to ensure the stability and performance of power systems. In this study, a novel optimization algorithm, the Sea Horse Optimizer (SHO) algorithm, was proposed for optimizing controller parameters in LFC problems of power system. The proposed SHO algorithm was tested on a two-area power system with photovoltaic system and reheat thermal units, under three different scenarios: a 10% load change in both area, large load disturbances, and varying solar radiation. The proposed algorithm optimizes the gain parameters of PI/PID controllers using performance metrics such as Integral of Absolute value of the Error (IAE), Integral of Square Error (ISE), Integral of Time multiplied by Square Error (ITSE), and Integral of Time multiplied by Absolute Error (ITAE). The study compared the performance of the SHO-optimized controller with other reported optimization algorithms such as Genetic Algorithm (GA), Firefly Algorithm (FA), Whale Optimization Algorithm (WOA), and Modified Whale Optimization Algorithm (MWOA). The study also evaluated the accuracy and effectiveness of the controllers using performance metrics such as Settling Time, Overshoot (M+), and Undershoot (M-). The results show that the SHO-tuned controller significantly reduces overshoot, undershoot, and settling time of the system oscillations compared to other algorithms. The study provides valuable insights into the optimization of LFC controllers and presents a significant contribution to the literature with its novel algorithm. The proposed SHO algorithm can be considered an effective alternative solution method for LFC in power systems.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

To enhance the safety of power grid operations, this study proposes a high-precision short-term photovoltaic power prediction method that integrates information from surrounding pho-tovoltaic stations and the Conv-LSTM-ATT model. In the deep learning prediction model, not only is numerical weather prediction (NWP) data from the target photovoltaic station used as input features, but also highly correlated features from nearby photovoltaic stations are incor-porated. The research begins by analyzing the correlation between irradiance and power se-quences, along with distance factors, to calculate a composite similarity index between the target and other regional photovoltaic stations. Stations with high similarity indices are then selected as data sources. Subsequently, Bayesian optimization techniques are employed to find the optimal data fusion ratios. Ultimately, using the selected data, power prediction mod-eling is conducted via the Conv-LSTM-ATT deep neural network. Experimental results con-firm the superiority of the proposed model, which demonstrates higher predictive accuracy compared to three other classical models. The data fusion strategy determined by Bayesian optimization significantly enhances prediction accuracy, reducing the root mean square error (RMSE) of the test set by 20.04%, 28.24%, and 30.94% for three weather types, respectively.

Despite a global push in the development and implementation of widespread alternative energy use, significant disparities exist across given nation-states. These disparities reflect both technical and economic factors, as well as the social, political, and ecological gaps between how communities see energy development and national/global policy goals. Known as the “local-national gap,” many nations struggle with fostering meaningful conversations about the role of alternative energy technologies within communities. Mitigation of this problem first requires understanding the distribution of existing alternative energy technologies at the local level of policymaking. Using the State of Georgia, U.S.A. as a case study, we present a model for analyzing how existing adoption trends enable/limit conversation at the scale of local governance (i.e., county governments). Leveraging existing work on the Gini Coefficient as a metric for measuring energy inequity, we argue these tools can be applied to analyze where gaps exist in ongoing solar adoption trends. As we demonstrate, communities that adopt solar tend to be concentrated in a few counties, indicating existing conversations are limited to a circumscribed set of social networks. This information and the model we demonstrate can enable focused qualitative analyses of existing solar trends, not only amongst high-adoption areas but within communities where little to no adoption has occurred.

In this paper, a multi-operator differential evolution algorithm (MODE) is proposed to solve the Optimal Power Flow (OPF) problem and is called MODE-OPF. The MODE-OPF utilizes the strengths of more than one differential evolution (DE) operator in a single algorithmic framework. Additionally, an adaptive method (AM) is proposed to update the number of solutions evolved by each DE operator based on both the diversity of population and quality of solutions. This adaptive method has the ability to maintain diversity at the early stages of the optimization process and boost convergence at the later ones. The performance of the proposed MODE-OPF is tested by solving OPF problems for both small and large IEEE bus systems (i.e., IEEE-30 and IEEE-118) while considering the intermittent solar and wind power generation. To prove the suitability of this proposed algorithm, its performance has been compared against several state-of-the-art optimization algorithms, where MODE-OPF outperforms other algorithms in all experimental results and thereby improving a network's performance with lower cost. MODE-OPF decreases the total generation cost up to 24.08%, the real power loss up to 6.80% and the total generation cost with emission up to 8.56%.

The stability issues in the widely known organic inorganic halide perovskite, CH₃NH₃PbI_3, lead to the development of alternative halide double perovskite materials which get great attention in recent times. Although the stability issue seems promising, both materials and device performance of these photovoltaic materials remain inferior and challenging for improvements. Furthermore, the power conversion efficiency of single junction organic inorganic halide perovskite is now 24.2% and 29.15% for textured monolithic perovskite/silicon tandem solar cell, but for all-inorganic halide perovskite solar cell is 7.11% and halide double perovskite solar cells based on Cs₂AgBiBr₆ and Cs₂TiBr₆ is 2.8% and 3.3%, respectively, which is far less than 24.2% and 29.15%, respectively. This creates big question and concern that can both all-inorganic halide perovskite solar cell and halide double perovskites solar cells really be an acceptable alternatives to replace organic inorganic halide perovskite solar cells or lead based perovskite solar cells in the market in order to realize the sustainable practical applications? Not only this concern, but also there are many other big challenges facing by halide double perovskite solar cells. Such big challenges include: a) geometric constraints and limited integration with interfacial materials, b) dynamic disorder and a wide band gap and localized conduction band caused by cubic unit cell which restrains the interactions of orbitals, c) high processing temperature which may limit on the diverse applications, d) low electronic dimensionality making them less appropriate for single junction solar cell purpose and etc. Moreover, origin of electronic and optical properties such as the polarizability, the presence of molecular dipoles and their influence on the dynamics of the photo-excitations in the halide double perovskites remains unlock concern that need to be elucidated. Now, another big question is how to develop overcoming mechanisms for such challenges. Can we really overcome these current limitations faced by halide double perovskites so that we use them for sustainable commercialization? This research roadmap for performance improvement is suggested focusing on: materials surface and bulk engineering, band gap engineering, interfacial engineering, composition engineering, doping engineering, device architectural engineering, polar and domain order engineering. This was the reason that this review was developed in order to forward great contributions to the readers and commercial ventures.

Passivating the grain boundaries is completely very crucial to achieve high power conversion efficiency in halide PSCs.

Recently, there has been a growing interest in the production of electricity from renewable energy sources (RES). The RES investment is characterized by uncertainty, which is long-term, costly, depend on feed-in-tariff and support schemes. In this paper, we address the real option valuation (ROV) of a solar power plant investment. The real option framework is investigated. This framework considers the renewable certificate price, furthermore the cost of delay between establishing and operating the solar power plant. The optimal time of launching the project and assess the value of deferred option are discussed. The new three stage numerical methods are constructed, the Lobatto3C-Milstein (L3CM) methods. The numerical methods are integrated with concept of Black-Scholes option pricing theory, and applied in option valuation for solar energy investment with uncertainty. The numerical results of L3CM, finite difference and Monte Carlo methods are compared to show the efficiency of our methods. Our data set refers to the Arab Republic of Egypt.

In the early decades of the 19th century, the deaf population in the eastern US and Canada was distributed across a vast area. After the 1817 founding of the American School for the Deaf (ASD) in Hartford, CT and the subsequent establishment of schools for the deaf in New York City (NYSD), Philadelphia, and many other US states, hundreds of deaf students called these schools home for several years. After leaving school, the early American Deaf community faced a challenge: How would the community maintain its social and linguistic ties across a vast geographical area once community members had dispersed to their hometowns? In this paper we analyze the attendance registries of two large gatherings of deaf individuals in Hartford in the years 1850 and 1854. These were among the largest and earliest known gatherings of deaf adults. The demographic data included in these registries open a window onto the evolving American Deaf community of the mid-19th century. Our analyses of the attendees’ school affiliations, ages, and marital status show that the signing community that had taken root among students at schools in Hartford and New York persisted among the adult graduates of those schools in towns across the northeastern US. We compare the places of residence of ASD and NYSD alumni in 1850 and 1854 to their hometowns when they first enrolled at school. Our comparisons suggest the mid-19th-century signing community had become more urban; it was centered to a greater extent in populous cities such as New York, Boston, and Hartford than had been true when the attendees had enrolled in school. We consider how the geography of deafness in the 19th century might inform our understanding of the sources of regional variation in ASL. We also consider how early cross-regional interactions may have inhibited such regional variation.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

Fossil fuels are non-renewable sources of energy, used particularly in developing countries. There are insufficient fossil fuels and their availability is gradually declining. This leads to a steady increase in prices. Renewable energy is clean, cost-effective and limitless. The considerable population growth and industrial growth have made the construction of solar power plants essential in developing countries. The study used Boolean logical-AHP techniques to select a suitable site for solar power in Duhok Governorate. The result indicated that 68.5% of the area in the governorate of Duhok is available for solar power station construction, especially the most appropriate zone which has 132.2 sq. km and can provide more than 8000 megawatts of solar energy. Most of the appropriate areas are in the south and southwest regions of the governorate, located mostly in the districts of Bardarash, Shekhan and Semel, situated between the major cities of Mosul, Erbil and Duhok. These locations can supply a significant amount of clean, renewable energy for these areas.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

This research article aims to present implementation and evaluation of the HPPT design based on using multi-parallel pumps switching for yielding performance with reference to potential change of daily irradiance. After that, the curve fitting of the hydraulic performance scenarios is tested to compare the hydraulic energy growth behaviors with reference to exponential and power growth models.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

This study addresses the pressing energy constraints in nations like Bangladesh by proposing the implementation of photovoltaic (PV) microgrids. Given concerns about environmental degrada-tion, limited fossil fuel reserves, and volatile product costs, renewable energy sources are gaining momentum globally. Our research focuses on a grid-connected solar PV system model at Char Jazira, Lalpur, Natore, Rajshahi, Bangladesh. Through PVsyst simulation software, we assess the performance ratio (PR) and system losses, revealing an annual solar energy potential of 3375 MWh at Standard Test Condition (STC) efficiency. After considering losses, the system generates 2815 MWh annually, with 2774 MWh exported to the grid. We analyze an average PR of 78.63% and calculate a levelized cost of energy (LCOE) of 2.82 BDT/kWh [1 USD = 110 BDT]. The financial assessment indicates a cost-effective LCOE for the grid-connected PV system, with an annual gross income of 27744 BDT from selling energy to the grid and operating costs of 64060.60 BDT/year. Remarkably, this initiative can prevent 33074.061 tCO2 emissions over the project’s 25-year lifespan.

This research work explains the practical realization of hybrid solar wind based standalone power system with maximum power point tracker (MPPT) to produce electrical power in rural places (residential applications). The solar inspired Ant Colony Optimization (ACO) based MPPT algorithm is employed for the purpose of fast and accurate tracking power from solar and wind system. Fuzzy Logic Control (FLC) inverter controlling strategy is adopted in this presented work compared to classical PI control. Moreover, single Cuk converter is operated as impedance power adapter to execute MPPT functioning. Satisfactory practical results have been realized using dSPACE (DS1104) platform that justify the superiority of proposed algorithms designed under various operating situations.

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

Energy demand and consumption in recent times have witnessed a rapid proliferation influenced by technological developments, increased population and economic growth. This has fuelled research trends in the domain of energy management employing tri-generation systems such as the combined cooling, heating and power (CCHP) systems. Furthermore, the incorporation of renewable energy, especially solar energy, to complement the thermal input by fossil fuels has facilitated the effectiveness and sustainability of CCHP systems. This study proposes a new approach to improve the overall efficiency of CCHP systems and compute the optimal design parameters in order to assist decision makers to identify the best geometrical configuration. A multi-objective optimization formulation of a solar-assisted CCHP system was adopted to maximize the net power, the exergy efficiency and minimize the CO2 emission using the greywolf optimization technique. In addition, the effects of the decision variables on the objective functions were analysed. The proposed optimization approach yielded 100 set of Pareto optimal solutions which would serve as options to the decision maker to make a selection in order to improve the performance of a solar-assisted CCHP system. This study demonstrates that the proposed approach is potentially suitable for the optimization of a solar-assisted CCHP system.

This study focused on the predictive models incorporating machine learning techniques that induce new dynamics for forecasting energy generation, enabling effective planning, financing, and system monitoring. The research developed a machine learning-based power generation prediction model tailored explicitly for Kenya's Garissa solar power plant. The selected model demonstrated a root mean squared error of 5.23 during evaluation, resulting in a prediction accuracy of 90.42%. This high accuracy indicates that the model can be relied upon for precise generation prediction, facilitating effective planning, and system performance monitoring

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Metal nanoparticles are used to modify/enhance the properties of a polymer matrix for a broad range of applications in bio-nanotechnology. Here, we study the properties of polymer/gold nanoparticle (NP) nanocomposites through atomistic molecular dynamics, MD, simulations. We probe the structural, conformational and dynamical properties of polymer chains at the vicinity of a gold (Au) NP and a functionalized (core/shell) Au NP, and compare them against the behavior of bulk PE. The bare Au NPs were constructed via a systematic methodology starting from ab-initio calculations and an atomistic Wulff construction algorithm resulting in the crystal shape with the minimum surface energy. For the functionalized NPs the interactions between gold atoms and chemically adsorbed functional groups change their shape. As a model polymer matrix we consider polyethylene of different molecular lengths, from the oligomer to unentangled Rouse like systems. By computing the different properties the concept of the interface, and the interphase as well, in polymer nanocomposites with metal NPs are critically examined. Results concerning polymer density profiles, bond order parameter, segmental and terminal dynamics show clearly that the size of the interface / interphase, depends on the actual property under study. In addition, the anchored polymeric chains change the behavior/properties, and especially the chain density profile and the dynamics, of the polymer chain at the vicinity of the Au NP.

Presently, Jordan confronts a double substantial challenge of enhancing energy security and mitigating greenhouse gas emissions. One of the most encouraging avenues to attain the objectives of sustainable development, energy security, and environmental conservation is to enhance the integration of renewable energy into the generation of electricity. In pursuit of this goal, the Jordanian government intends to expand investments in the green energy sector, with solar and wind energy poised to play a key role in satisfying energy demands and cultivating an environmental sustainability. This paper aims to examine the distinctive dynamics, challenges, obstacles, and potential solutions corresponding to the establishment of community solar and wind farms in Jordan suburban areas. It aims to highlight the opportunities and barriers influencing the track of sustainable energy adoption in the country. Through a comprehensive analysis of the Jordanian context, the goal is to extract insights that can guide policies and practices. Additionally, the findings may serve as a valuable benchmark for other regions confronting similar challenges on their pursuit for a sustainable energy future.

A programmable DC power supply with Real-time Digital Simulator (RTDS)-based photovoltaic (PV) Power Hardware-In-the-Loop (PHIL) simulators have been used to improve the control algorithm and reliability of PV Inverter. This paper proposes a supervisory control algorithm for PV PHIL simulator with non-RTDS device that is an alternative solution of high cost PHIL simulator. However, when such a simulator with conventional algorithm which is used in RTDS is connected to a PV inverter, the output is in the transient state and it makes it impossible to evaluate the performance of the PV Inverter. Therefore proposed algorithm controls the voltage and current target values according to the constant voltage (CV) and constant current (CC) modes to overcome the limitation of the Computing Unit, DC power supply and also uses a multi-rate system to account for the characteristics of each component of simulator. A mathematical models of a PV system, programmable DC power supply, isolated DC measurement device and Computing Unit are integrated to form a real-time processing simulator. Performance tests using a PV PHIL simulator which is applied proposed algorithm connected a PV inverter are carried out and proved superiority and utility of this method against conventional methods.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.