Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

The second article in the series presents the application of the Smoothed Particle Hydrodynamics (SPH) method to modelling of batch crystallisation in stirred tanks. A methodology to integrate the population balance equations (PBE) in parallel and independently from the Navier-Stokes equations is demonstrated. The benefits of the proposed methodology in terms of computational requirements, accuracy and availability of the crystal size distribution are discussed. The specific formulation of the SPH equations where the resulting system of ordinary differential equations is solved using the weighted contributions rather than numerically by solving a linear system of equations allows for massive parallelisation and a very loose coupling of the population balance and the fluid dynamics. It has been demonstrated, that the population balance equations can be solved on a Shared Memory Architecture (SMA) system using the OpenMP interface while the fluid dynamics equations being computed independently on a General Purpose Graphics Processing Unit (GPGPU) using the NVidia CUDA technology. This way, a significant portion of the computational overhead due to the large number of additional transport equations resulting from the discretisation of the population balance was removed: the SPH simulation coupled with 200 population balance equations was only 40% slower compared to SPH-only simulation. Two methods for the solution of population balance equations that preserve full crystal size distribution were implemented: discretised population balance (DPB) and method of characteristics (MOCH). The DPB equations are solved using the high-resolution finite-volume method with flux limiter and the effect of a large number of different flux limiters have been investigated. Both methods were validated using the case studies from the literature where an analytical solution can be derived. The developed models were applied to a numerical solution of coupled computational fluid dynamics and population balance equations to model a batch crystallization process. The effect of the hydrodynamics on the local temperature/supersaturation and the resulting crystal size distribution was captured and compared to the ideal mixing case. The simulation results from the DPB and MOCH methods were compared in terms of computational requirements and accuracy and MOCH selected as computationally more efficient and accurate.

In this review, we summarize recent progress in crystal growth and understanding the influence of crystal structure on the superconductivity in pure and Pb-doped Bi2Sr2CuOy (Bi-2201) materials belonging to the overdoped region of high temperature cuprate superconductors. The crystal growth of Bi-2201 superconductors faces challenges due to intricate materials chemistry and lack of knowledge of corresponding phase diagrams. Historically, a crucible-free floating zone method has emerged as the most promising growth approach for these materials, resulting in high-quality single crystals. This review outlines the described in the literature and the authors' synthesis endeavors, encompassing Pb-doped Bi-2201 crystals, detailed structural characterization of as-grown and post-growth annealed samples, and highlights optimal growth conditions that yield large-size, single-phase, and compositionally homogeneous Bi-2201 single crystals.

Crystal structures of simple metals and binary alloy phases based on the face-centered cubic (fcc) structure are analyzed within the model of Fermi sphere – Brillouin zone interactions to understand the stability of original cubic structure and derivative structures with distortions, superlattices and vacancies. Examination of the Brillouin-Jones configuration in relation to the nearly-free electron Fermi sphere for several representative phases reveals significance of the electron energy contribution to the phase stability. Representation of complex structures in the reciprocal space clarifies their relationship to the basic cubic cell.

Hydrogen is the lightest atom and composes roughly half of the atomic content in macromolecules, yet their location can only be inferred or predicted in most macromolecular structures. This is because hydrogen can rarely be directly observed by the most common structure determination techniques (such as X-ray crystallography and electron cryo-microscopy). However, knowledge of hydrogen atom positions, especially for enzymes, can reveal protonation states of titratable active site residues, hydrogen bonding patterns, and the orientation of water molecules. Though we know they are present, this vital layer of information, which can inform a myriad of biological processes, is frustratingly invisible to us. The good news is that, even at modest resolution, neutron crystallography (NC) can reveal this layer and has emerged this century as a powerful tool for elucidating enzyme catalytic mechanisms. Due to its strong and coherent scattering of neutrons, incorporation of deuterium into the protein crystal amplifies the power of NC. This is especially true when solvation and the specific participation of key water molecules are crucial for catalysis. Neutron data allow the modeling of all three atoms in water molecules and have even revealed previously unobserved and unique species such as hydronium (D3O+) and deuteroxide (OD-) ions as well as lone deuterons (D+). Herein, we briefly review why neutrons are ideal probes for identifying catalytically important water molecules and these unique water-like species, limitations in interpretation, and four vignettes of enzyme success stories from disparate research groups. One of these groups was that of Dr. Chris G. Dealwis, who died unexpectedly in 2022. As a memorial appreciation of his scientific career, we will also highlight his interest and contributions to the neutron crystallography field. As both the authors were mentored by Chris, we feel we have a unique perspective on his love of molecular structure and admiration for neutrons as a tool to query those structures.

Nuclear waste is one of the most important environmental problems of nuclear power plants. A novel renewable distillation method has been proposed for an on-site recycling of the spent nuclear fuel and separation of its valuable components from the fissile isotopes, which is especially applicable for reactors using liquid fuels.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Ruminant animals naturally emit methane gas owing to anaerobic microbial fermentation in the rumen, and these gases are considered major contributors to global warming. Scientists worldwide are attempting to minimize methane emissions from ruminant animals. Some of these attempts include the manipulation of rumen microbes using antibiotics, synthetic chemicals, dietary interventions, probiotics, propionate enhancers, stimulation of acetogens, manipulation of rumination time, vaccination, and genetic selection of animals that produce low methane (CH4). The majority of synthetic additives are harmful to both beneficial rumen microbes and the host or only temporarily affect methanogenesis. Phytogenic feed additives (PFAs) have recently emerged as the best alternatives to antibiotics and synthetic chemicals because of growing public concerns regarding drug resistance and the negative impacts of antibiotics and synthetic chemicals on humans, livestock, and the environment. These additives reduce methane production and improve the volatile fatty acid profile. In this review, we provide an overview of PFA sources and how their bioactive components affect the rumen microbiome to reduce methane emissions. Additionally, we highlight the mechanisms of action of PFAs as a whole as well as some of their bioactive components.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

General derivation of the well-known Ren-Otsuka relation, 1/α (dTo)/dx=-α/β (where To, x, α and β(>0) are the transformation temperature, the composition, as well as the composition and temperature coefficient of the critical shear constant, c’, respectively) for shape memory alloys, SMAs, is provided based on the similarity of interatomic potentials in the framework of dimensional analysis. A new dimensionless variable, to(x)=(To (x))/(Tm (x) ), describing the phonon softening (where Tm is the melting point) is introduced. The dimensionless values of the heat of transformation, H, and entropy, S as well as the elastic constants c’, c44, A=c44/c' are universal functions of to(x) and have the same constant values at to(0) within sub-classes of host SMAs having the same type of crystal symmetry change during martensitic transformation. The ratio of (dto)/dx and α has the same constant value for all members of a given sub-class and relative increase of c’ with increasing composition should be compensated by the same decrease of to. In the generalized Ren-Otsuka relation the anisotropy factor, A appears instead of c’ and α as well as β are the differences of the corresponding coefficients for the c44 and c’ elastic constants. The obtained linear relation between h and to rationalizes the observed empirical linear relations between the heat of transformation measured by DSC (QAM) and the martensite start temperature, Ms.

This paper proposes an innovative approach to address the challenge of softening deformation of thermal-curable thermosets during additive manufacturing. This approach involves the development of a composite powder composed of thermosetting materials with distinct curing temperatures, the utilization of Cold Spray Additive Manufacturing (CSAM) technology for 3D printing, and the application of a stepwise isothermal curing process. The corresponding effectiveness is validated by case studies. The results demonstrate that samples printed via CSAM maintain a solid state without deformation. During the post-curing process, each component of the composite material cures independently while the other components remain in a solid state, providing structural support for the whole material, thereby effectively reducing the softening deformation during the post-curing process. This approach offers a novel perspective for the additive manufacturing of thermal-curable thermosets.

The present paper reports exact results for the muon self-energy and anomalous g-factor. A unique to the muon cut-off terms that remove the radial singularity in the system and regularize the corresponding electrodynamics are presented. Equations of motion and a transcendental equation satisfied by the muon anomalous g-factor are derived, with solution a_m=0.001165920162(198). The obtained value matches the latest experimental one found in the literature to about 0.43 ppb ruling out a possible tension between theory and experiment.

From their discovery in 2002, BRAF mutations have been identified as clear drivers of oncogenesis in several cancer types. Currently, their incidence rate is nearly 7% of all solid tumors with BRAF V600E constituting approximately 90% of these diagnoses [1]. In melanoma, thyroid cancer, and histiocytic neoplasms, BRAF hotspot mutations are found at a rate of about 50%, while in lung and colorectal cancers they range from 3 to 10% of reported cases [2-5]. Though present in other malignancies such as breast and ovarian cancers, they constitute a small portion of diagnoses (<1%). Given their frequency along with advancements in screening technologies, various methods are used for the detection of BRAF-mutant cancers. Among these are targeted next-generation sequencing (NGS) on tumor tissue or circulating tumor DNA (ctDNA) and immunohistochemistry (IHC)-based assays. With advancements in detection technologies, several approaches have been taken for the treatment of BRAF mutant cancers. In this review we retrace the milestones that led to the clinical development of targeted therapies currently available for these tumors.

The radiation-induced optical absorption at 1.5-5.5 eV (up to the beginning of fundamental absorption) has been analyzed in CVD diamond disks exposed to 231-MeV 132Xe ions with four fluences from 1012 to 3.81013 cm-2. The 5-mm diameter samples (thickness 0.4 mm) were prepared by Diamond Materials, Freiburg (Germany), average grain size at growth site was around 80 m, the range of xenon ions was R= 11.5 m. The intensity of several bands grows with ion fluence thus confirming radiation-induced origin of the defects responsible for these bands. The recovery of radiation damage has been investigated via isochronal (stepwise) thermal annealing procedure up to 650°C, while all spectra were measured at room temperature. Based on these spectra, the annealing kinetics of several defects, in particular carbon vacancies (GR1 centers with a broad band 2 eV) and complementary C-interstitial-related defects ( 4 eV), as well as vacancies located nearby nitrogen substitutional atoms (narrow bands around 2.5 eV) have been constructed. The experimental kinetics have also been analyzed in terms of the diffusion-controlled bimolecular reactions. The migration energies of tentatively interstitial atoms (mobile components in recombination process) are obtained, their dependence on the irradiation fluences is discussed.

Fungi inhabiting deep subseafloor sediments have been shown to possess anaerobic methane (CH₄) production capabilities under atmospheric conditions. However, their ability to produce CH₄ under in situ conditions with high hydrostatic pressure (HHP) remains unclear. Here, Schizophyllum commune 20R-7-F01, isolated from ~ 2 km below the seafloor, was cultured in Seawater Medium (SM) in culture bottles fitted with sterile syringes for pressure equilibration. Subsequently, these culture bottles were transferred into 1-liter stainless steel pressure vessels at 30 °C for 5 days to simulate in situ HHP and anaerobic environments. Our comprehensive analysis of bioactivity, biomass, transcriptomics revealed that S. commune not only survived but significantly enhanced CH₄ production, reaching approximately 2.5 times higher levels under 35 MPa HHP compared to 0.1 MPa standard atmospheric pressure. Pathways associated with carbohydrate metabolism, methylation, hydrolase activity, cysteine and methionine metabolism, and oxidoreductase activity were notably activated under HHP. Specifically, key genes involved in fungal anaerobic CH₄ synthesis, including methyltransferase mct1 and dehalogenase dh3, were upregulated 7.9- and 12.5-fold, respectively, under HHP. Enhanced CH₄ production under HHP was primarily attributed to oxidative stress induced by pressure, supported by intracellular Reactive Oxygen Species (ROS) levels and comparative treatments with cadmium chloride and hydrogen peroxide. These findings suggest that fungi persisting in deep-sea sediments over millions of years have the potential to significantly contribute to global CH₄ flux.

This study presents a comprehensive approach to calculating the free energy of hydration of methane using Molecular Dynamics simulations. We employed the Free Energy Perturbation (FEP) method to determine the Gibbs free energy associated with transferring a methane molecule into water. Simulations were conducted in a cubic simulation box containing one methane molecule and 1000 TIP4P water molecules. The forward and backward routes were both analyzed, providing consistent free energy differences, which validates the robustness of our methodology. The Gibbs free energy profiles demonstrated characteristic energy barriers and stabilization points, indicative of the interaction dynamics in the solvation process. The results demonstrate the robustness of the FEP method implemented in LAMMPS, yielding free energy in close agreement with experimental data and previous computational studies. The calculated free energy differences for methane hydration exhibited deviations of 13% and 8% for the forward and backward routes, respectively, compared to experimental values. These findings underscore the accuracy and efficiency of using LAMMPS for free energy calculations, contributing to the broader understanding of solvation thermodynamics. Additionally, radial distribution functions were analyzed to provide insights into the structural arrangement of water molecules around methane, revealing strong interaction between methane's carbon atom and water molecules.

In this work various sample of primary aluminum dross were investigated for composition and evaluation of hydrogen generation via hydrolysis in low concentration alkali solution. Composi-tion revealed low to moderate aluminium content and hydrolysis reactions showed low hydrogen generation volumes per sample mass as well as purity, where composition plays substantial role in the hydrogen evolution, yet showing that there is possible place for dross use in hydrogen generation. It was revealed that some dross samples in addition to hydrogen also release methane via hydrolysis. Rection rate was obtained by the shrinking core model, written for spherical solid particles. Sample composition on hydrogen generation volume is compared to known literature.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

A binary biomass-based solid electrolyte film (LSE) was successfully synthesized through the incorporation of lignin nanoparticles (LNP) with sodium alginate (SA). The impact of the mass ratio of SA to LNP on the microstructure, porosity, electrolyte absorption capacity, ionic conductivity, and electrochemical properties of the LSE was thoroughly investigated. The results indicated that as the proportion of SA increased from 5% to 15% LNP, the pore structure of the LSE became increasingly uniform and abundant. Consequently, enhancements were observed in porosity, liquid absorption capacity, ionic conductivity, and overall electrochemical performance. Notably, at a SA amount of 15% LNP, the ionic conductivity of resultant LSE-15 was recorded at 14.10 mS cm1, with porosity and liquid absorption rates reaching 308% and 58.4%, respectively. LSE-15 was employed as a solid electrolyte, while LNP-based carbon aerogel (LCA) served as the two electrodes in the construction of a symmetric all-solid-state supercapacitor (SSC). The SSC device demonstrated exceptional electrochemical storage capacity, achieving a specific capacitance of 197 F g1 at 0.5 A g1, along with maximum energy and power density of 27.33 W h kg1 and 4998 W kg1, respectively. Furthermore, the SSC device exhibited highly stable electrochemical performance under extreme conditions, including compression, bending, and both series and parallel connections. Therefore, the development and application of the binary biomass-based solid electrolyte film in supercapacitors represent a promising strategy for harnessing high-value biomass resources in the field of energy storage.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

Solid-state batteries (SSBs) have emerged as a promising alternative to conventional lithium-ion batteries, with notable advantages in safety, energy density, and longevity, yet the environmental implications of their lifecycle, from manufacturing to disposal, remain a critical concern. This review paper examines the environmental impacts associated with the production, use, and end-of-life management of SSBs, starting with the extraction and processing of raw materials which highlights significant natural resource consumption, energy use, and emissions. A comparative analysis with traditional battery manufacturing underscores the environmental hazards of novel materials specific to SSBs. The review also assesses the operational environmental impact of SSBs by evaluating their energy efficiency and carbon footprint in comparison to conventional batteries, followed by an exploration of end-of-life challenges including disposal risks, regulatory frameworks, and the shortcomings of existing waste management practices. A significant focus is placed on recycling and reuse strategies, reviewing current methodologies like mechanical, pyrometallurgical, and hydrometallurgical processes, along with emerging technologies that aim to overcome recycling barriers, while also analyzing the economic and technological challenges of these processes. Additionally, real-world case studies are presented, serving as benchmarks for best practices and highlighting lessons learned in the field. In conclusion, the paper identifies research gaps and future directions for reducing the environmental footprint of SSBs, underscoring the need for interdisciplinary collaboration to advance sustainable SSB technologies and contribute to balancing technological advancements with environmental stewardship, thereby supporting the transition to a more sustainable energy future.

The field of biosensors has found great use for surface plasmon resonance (SPR), which has attracted attention for its multiple applications. With the goal of early cancer detection at the level of a single living cell, this research numerically investigates a very sensitive D-shaped fiber-optic biosensor based on surface plasmon resonance (SPR). The titanium oxide (TiO2) is coated on gold (Au), which is utilized as a thin-film plasmonic material in the suggested biosensor structure. The guiding of light in the fiber is modeled using the finite element method (FEM) when six different types of healthy human cells and their malignant counterparts are exposed to its sensitive region. Refractive index (RI) differences between cancer cells and healthy cells are found through the analysis of the optical spectra and their amplitudes. This enables us to identify small changes in the optical characteristics of cells that could be a sign of pathogenic alterations. In this work, we concentrated on three forms of cancer: skin cancer (basal cell) and breast cancer (MDA-MB-231 and MCF-7). The results show which parameters are optimal to ensure that the sensor performs well when used to detect the three types of cancer under study. When the suggested sensor’s performance is compared to SPR sensors that have previously been published in the literature, it becomes clear that our sensor offers great promise for early cancer detection.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

We investigate perovskite oxides from different aspects, namely their pseudoharmonic dynamical properties, their dynamical properties when strong anharmonicity exists and the intriguing functionalities arising from domain walls. Taking these viewpoints together yields a rather complex picture of this material class which was not anticipated in previous approaches. It opens pathways to novel applications and reveals the rich ground states beyond the fictitious belief in ‘simplicity of perovskites and such structures’.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

Due to its high short-term global warming potential (GWP) compared to carbon dioxide, methane (CH₄) is a considerable agent of climate change. This research is aimed at analyzing data on methane gathered at the GAW (Global Atmosphere Watch) station of Lamezia Terme (Calabria, Southern Italy) spanning seven years of continuous measurements (2016-2022) and integrating the results with key meteorological data. Compared to previous studies on detected methane mole fractions at the same station, daily-to-yearly patterns have become more prominent thanks to the analysis of a much larger data set. Overall, the yearly increase of methane at the Lamezia Terme station is in general agreement with global measurements by NOAA, though local peaks are present, and an increase linked to Covid-19 is identified. Seasonal changes and trends have proved to be fully cyclic, with the daily cycles being largely driven by local wind circulation patterns and synoptic features. Outbreak events have been statistically evaluated depending on their weekday of occurrence to test possible correlations with anthropic activities. A cross analysis between methane peaks and specific wind directions has also proved that local sources may be deemed responsible for the highest mole fractions.

The emphasis in the automotive industry towards sustainable mobility has led to a significant interest in hybrid-electric propulsion systems with high energy density batteries. Addressing the needs of this strategy, the battery market is exploring new technologies to improve the safety and lifespan of electric vehicles. To this end, there is a focus on the all-solid-state battery (ASSB) technology for its cycle capabilities. Filling the current void in the literature pertaining to accurate ageing models for ASSBs, in this work, we present an enhanced version of the numerical ageing model, originally developed for liquid electrolyte based batteries, to forecast the development of the solid electrolyte interface layer that is the major cause of battery capacity fading. The model has been tested on prototype batteries and reveals an accuracy of 99%. The capacity fade in ASSBs has been investigated under different conditions, and the enhanced ageing model has been validated using experimental data from these batteries. The findings suggest that there is potential for solid-state batteries to be commercialized, although significant work is needed to match the manufacturing level of lithium-ion batteries with liquid electrolytes.

Hydrogen and carbon monoxide over-equilibria have been found computationally in kinetic dependencies of methane reforming catalytic reactions (steam and dry reforming) using conditions of the conservatively perturbed equilibrium (CPE) phenomenon, i.e. at the initial equilibrium concentration of hydrogen or carbon monoxide.  The influence of pressure, temperature, flow rate and composition of the initial mixture on the position of the CPE point (the extremum point) was investigated in a wide domain of parameters. It is demonstrated that the CPE phenomenon significantly increases the product concentration (H2 and CO) at the reactor length which is significantly less than the reactor length required to reach the equilibrium. The CPE-point was interpreted as the “turning point” in kinetic behavior.  Recommendations on the temperature and pressure regimes are different from the traditional ones related to the Le Chatelier’s law. Obtained results provide valuable information on optimal reaction conditions for complex reversible chemical transformations, offering potential applications in chemical engineering processes.

This study investigates the impact of thin flame combustor design on hydrogen flame characteristics and combustion performance through numerical simulations. Variations in flame shape and combustibility between 100% methane and 100% hydrogen combustion are analyzed. Three combustor header shapes (flat, concave, and convex) are modeled to assess their influence on flame behavior. Results show distinct flow patterns, with concave headers promoting strong central flows and convex headers dispersing the flow outward. Temperature field analysis indicates that hydrogen flames have higher temperatures and shorter quenching distances compared to methane flames. A comparative analysis of combustion products is conducted to evaluate combustion performance and NOx emissions. Consequently, the concave header has high combustibility and increases temperatures and NOx fraction in hydrogen combustion.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Blood vessels are essential for maintaining tumor growth, progression, and metastasis, yet the tumor vasculature is under a constant state of remodeling. Since the tumor vasculature is an attractive therapeutic target, there is a need to predict the dynamic changes in intratumoral fluid pressure and velocity which occur across the tumor microenvironment (TME). The goal of this study is to get insight into perfusion anisotropy within lung tumors. To achieve this goal, we used the perfusion marker Hoechst 33342 and vascular endothelial marker CD31 to stain tumor sections from C57BL/6 mice harboring Lewis Lung Carcinoma tumors on their flank. Vasculature, capillary diameter, and permeability distribution were extracted at different time points along the tumor growth curve. A computational model was generated applying a unique modeling approach based on the smeared physical fields (Kojic Transport Model, KTM). KTM predicts spatial and temporal changes in intratumoral pressure and fluid velocity within the growing tumor. Anisotropic perfusion occurs within two domains - capillary and extracellular space. Anisotropy in tumor structure causes nonuniform distribution of pressure and fluid velocity. These results provide insights regarding local vascular distribution for optimal drug dosing and delivery to better predict distribution and duration of retention within the TME.

Solving the problem of searching for new scintillators based on available materials, we were the first to obtain and study a single crystal of CsI doped with divalent ytterbium ions. This work was directed to study of luminescence mechanism of Yb2+ ions and excitation transfer from crystalline matrix of CsI to dopant ions under VUV excitation. Using time-resolved spectroscopy, spin-allowed and spin-forbidden radiative transitions of ytterbium ions at room temperature were discovered. At 10 degrees, the emission of self-trapped excitons was detected. UV and VUV excitation spectra were obtained in the emission bands of ytterbium and self-trapped excitons. It was found that Yb2+ luminescence is excited in the excitonic region in the range of 10-45 eV. The mechanism of charge compensation of Yb2+ ions in a CsI crystal was also studied, the spectrum of the thermally stimulated depolarization current was measured, and the activation energies of the two observed peaks were calculated. These peaks belong to impurity-vacancy complexes in two different positions.It is concluded that Yb2+ ions are promising dopants for CsI scintillators and X-ray phosphors in combination with SiPM photodetectors.

This research project aimed to address the growing concern about methane emissions from seaweed by developing a Convolutional Neural Network (CNN) model capable of accurately predicting these emissions. The study used PANDAS to read and analyze the dataset, incorporating statistical measures like mean, median, and standard deviation to understand the dataset. The CNN model was trained using the ReLU activation function and mean absolute error as the loss function. Model performance was evaluated through MAPE graphs, comparing the mean absolute percentage error (MAPE) between training and validation sets and between true and predicted emissions, and analyzing trends in yearly greenhouse gas emissions. The results demonstrated that the CNN model achieved a high level of accuracy in predicting methane emissions, with a low MAPE between the expected and actual values. This approach should enhance our understanding of methane emissions from Sargassum, contributing to more accurate environmental impact assessments and effective mitigation strategies.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

Femtosecond laser two-photon polymerization (TPP) technology, known for its high precision and capability to fabricate arbitrary 3D structures, has been widely applied in the production of various micro-nano optical devices, achieving significant advancements particularly in the field of photonic wire bonding (PWB) for optical interconnects. Currently, research on optimizing both the optical loss and production reliability of polymeric photonic wires is still in its early stages. One of the key challenges is that inadequate metrology methods cannot meet the demand for multiphysical measurements in practical scenarios. This study utilizes in-situ scanning electron microscopy (SEM), for the first time, to monitor the working PWBs fabricated by TPP technology at the microscale. Optical and mechanical measurements are made simultaneously to evaluate the production qualities and to study the multiphysical coupling effects of PWBs. The results reveal that photonic wires with larger local curvature radii are more prone to plastic failure, while those with smaller local curvature radii recover elastically. Furthermore, larger cross-sectional dimensions contribute dominantly to the improved mechanical robustness. The optical loss deterioration of the elastically deformed photonic wire is only temporary, which can be fully recovered when the load is removed. After further optimization based on the results of multiphysical metrology, the PWBs fabricated in this work achieve a minimum insertion loss of 0.6 dB. In this study, the multiphysical analysis of PWBs carried out by in-situ SEM metrology offers a novel perspective for optimizing the design and performance of microscale polymeric waveguides, which could potentially promote the mass production reliability of TPP technology in the field of chip-level optical interconnection.

As an important element of methane prevention in mining facilities, measurements of concentration serve to obtain information about methane hazards. Information about methane concentration must be linked to the place and time of its occurrence to create valuable data for ongoing hazard analysis. The article presents the results of a methane hazard analysis based on an airflow and methane concentration model, validated using measurement data. Subsequently, simulations of crew movement and the operation of individual methane detectors working according to the algorithms of the Methane Hazard Detection System were conducted based on this model.

Organic soil amendments, such as composts, mitigate the environmental burdens associated with wasting organic resources. Although compost application to soil enhances an agroecosystem's capacity to store carbon and produce food, studies investigating the agronomical efficacy and their ability to ameliorate drought stress when used as a soil amendment are minimal. In this study, we produced and used a nutrient rich co-compost through the composting of sludge, a nitrogen-rich organic material with carbon rich municipal solid wastes (MSW) to evaluate the agronomic efficacy of the MSW derived co-compost and their ability to ameliorate drought stress. Application of co-compost significantly enhanced growth and yield of lettuce and maize, by a magnitude comparable to chemical fertilizers. Furthermore, under drought stress, lettuce plants grown under co-compost soil amendment grew much better with less wilting, more biomass and yield, and improved root growth. Also, co-compost application enhanced relative root mass ratio (RRMR) under drought stress, indicative that co-compost amendment increased the allocation of biomass to the roots, which is an important morphological attribute for drought adaptability. K content in both leaves and roots of plants amended with co-compost was also higher under drought stress, which may have played a role in osmotic adjustment, consequently, the plants exhibited higher leaf relative water content (RWC). Other nutrient elements that were significantly enhanced by co-compost application included Mg, Ca, Fe and Cu. These results provide evidence that MSW co-composting could optimize organic resource recycling for climate change mitigation and agricultural productivity while minimizing nutrient losses from agroecosystems.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Dental implantology has evolved greatly as a result of the application of biomechanical engineering concepts, notably the utilization of additive manufacturing technologies that recreate the intricate architecture of real bone. This technique intends to improve functional compatibility with bone tissue while also addressing continuing problems of stress distribution inside dental implants. The research examines two types of dental implants: fully gyroid latticed and hybrid gyroid latticed with a solid neck, comprising three different cell sizes—FI-111, FI-222, FI-333, and their hybrid equivalents HI-111, HI-222, and HI-333. Traditional solid implants often cause stress shielding, which reduces long-term osseointegration and implant durability. Developed using nTopology for lattice configuration and meshing, this design undergoes a comprehensive stress analysis using finite element analysis (FEA). The study seeks to determine the most efficient implant design by maximizing stress distribution and mechanical stiffness. Analyses suggest that hybrid latticed implants, notably the HI-222 type, possess superior mechanical characteristics. These implants successfully balance stiffness and flexibility, reducing stress concentrations and improving stress distribution throughout the implant structure. This balance is critical for decreasing micromotions at the bone-implant interface, boosting osseointegration, and, ultimately, increasing implant longevity and success rates in clinical settings. The paper describes a substantial redesign of dental implants by combining biomechanical engineering and modern additive manufacturing. The novel proposed hybrid structure not only addresses typical challenges such as stress shielding, but it also establishes new standards in implantology, potentially leading to better clinical results and patient quality of life. This complete approach emphasizes the ability of personalized implant designs to fulfill individual clinical demands, indicating a significant improvement in dental treatment technology.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

This paper reviews the requirements for the production, quality, and quality assurance of solid recovered fuels (SRF) that are increasingly used for the substitution of fossil fuels in the indus-trial utilities. The economical, technological and environmental aspects should be considered before using SRF as an alternative fuel. In general, the most important factors determining the commercial production of SRF referred to the calorific values and their available amounts adopted in the starting materials. Furthermore, the low-melting impurities and undesired constituents/elements, including chlorine, sulfur, potassium and sodium, may pose negative impacts on air pollutant emission and slagging & fouling in the process utilities. In this regard, the vent emitted from the industrial utilities must comply with the effluent standards of station-ary sources like particulate, sulfur oxides, nitrogen oxides, heavy metals (e.g., lead, cadmium, and mercury) and dioxins. For these reasons, this work will summarize the legal or regulatory requirements under development in Asian countries (i.e., Japan, South Korea, and Taiwan) and European Union (EU). Finally, the outlook of solid recovered fuel (SRF) in the waste manage-ment and industrial sectors will be addressed to echo the sustainable development goals (SDGs).

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

For very first time, we report the synthesis of 8-(2-methoxyphenyl)-6-methyl-2-(1-methyl-1H-benzo[d]imidazol-2-yl)quinoline 1. This was achieved in several steps, including usage of Suzuki reaction for functionalization of 2-(1H-benzo[d]imidazol-2-yl)quinoline moiety. The new compound exhibits blue fluorescence. Its structure was confirmed with 1D- and 2D-NMR spectroscopy, IR-spectroscopy, high-resolution mass spectrometry and X-ray analysis.

Rechargeable solid-state batteries (SSBs) offer enhanced safety, higher energy density, and longer cycle life compared with conventional lithium-ion batteries, making them a promising solution for electric vehicles, grid storage, and other high-demand applications. However, challenges such as interface stability, low ionic conductivity, and manufacturing scalability hinder their commercial viability. This research provides a comprehensive cross-sectional thematic and bibliometric analysis of recent SSB research, focusing on four key areas: electrolyte engineering, electrode engineering, battery architecture, and performance evaluation. By analyzing publications from major databases, this study highlights the latest innovations, including improved solid electrolytes, advanced electrode materials, and novel architectures that enhance both performance and manufacturability. The findings offer valuable insights for researchers, engineers, and industry stakeholders by identifying critical gaps in the field and highlighting future research directions. The work examines progress in interface optimization, ion transport improvements, and scalable production techniques, which are crucial for advancing SSB technology. By presenting a detailed review of key developments and challenges, this study contributes to a deeper understanding of SSB progress and its potential to revolutionize the energy storage industry. The results will guide researchers in targeting high-impact areas and help industry leaders and policymakers strategize the commercial deployment of SSBs in electric vehicles, stationary energy storage, and other applications requiring reliable and efficient energy solutions.

Protein degradation is a biological phenomena essential for cellular homeostasis and survivor. Selective protein degradation is performed by the ubiquitination system which selectively target proteins that need to be eliminated and lead them to proteasome degradation. In this review, we focus on the ubiquitin-conjugating enzyme E2 O (UBE2O) and highlight the role of UBE2O in many biological and physiological process. We further discuss the UBE2O implications in various human diseases, particularly in leukemias and solid cancers and suggest how UBE2O targeting could be novel strategy in the treatment of different human neoplasia.

Ghana spends over $4000 (US dollars) annually managing municipal solid waste (MSW) with little improvement in regional sanitation. Energy demand in the country is also on the rise. Therefore, addressing waste problems via the waste-to-energy valorization approach is necessary for dual benefits. This paper thus seeks to comprehensively review Ghana's MSW's proximate and ultimate compositions for biological and thermochemical conversions. Studies between 2011 and 2024 were analyzed. The findings revealed that the organic fraction of Ghana’s MSW is currently about 10.47Kt per day. The proximate analysis reveals a moisture content from 13.55 – 61.9 %, volatile matter ranges from 6.24 - 80.25%, and the calorific value ranges from 14.96-21.46MJ/Kg. The ultimate analysis revealed that the carbon-to-nitrogen ratios range from 24.3-32.2, and the hydrogen content ranges from 5.53-22.8%. The sulphur and nitrogen contents were below 0.6 and 1.7% respectively. Approximately 2,534.65 GWh of electricity is estimated from the organic fraction. Ghana’s MSW is more suited for biochemical conversions.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

One of the possible mechanisms causing significant emissions of methane into the atmosphere within the Arctic shelf may be the decomposition of gas hydrates. Their accumulations within the Arctic shelf formed during Ice Age almost simultaneously with the formation of permafrost, which contributed to the emergence of a zone of stable existence of gas hydrates. The subsequent flooding of the Arctic shelf led to the degradation of the permafrost and the violation of the conditions for the existence of hydrates. To assess the state of the stability zone, methods of mathematical numerical modeling are used. Standard seismic methods are widely used to localize gas hydrates, but monitoring their physical state requires the development of fundamentally new approaches based on solving multiparameter inverse seismic problems. In particular, the degree of attenuation of seismic energy is one of the objective parameters for assessing the consolidation of gas hydrates: the closer they are to the beginning of decomposition, the higher the attenuation, and hence the lower the quality factor. Thus, the methods of seismic monitoring of the state of gas hydrates in order to predict the possibility of developing dangerous scenarios should be based on solving a multi-parameter inverse seismic problem. This publication is devoted to the presentation of this approach.

(1) Background: With the rising incidence of life expectancy, obesity, and tumours, understanding the incretory influence of adipose tissue in tumorigenesis becomes increasingly important. As the adipokines leptin and adiponectin are released by fat tissue, we aimed to analyse the expression of their respective receptors in tumours for which an association with obesity is epidemiologically hypothesized; (2) Methods: The expression of leptinR and adipoR1 were analysed in cohorts of renal cell cancer (n = 391), cervical cancer (n = 155), vulvar cancer (n = 107), and endometrial cancer (n = 90) by immunohistochemistry and correlated with clinicopathological parameters including survival times; (3) Results: Expression of leptinR was high in renal cell cancer (62.2% of cases), vulvar carcinoma (50%) and endometrial cancer (80.5% of tissue-samples). High expression was associated with favourable clinicopathological markers and longer overall survival times in renal cell cancer and vulvar cancer. AdipoR1 was only weakly expressed in all four tumor entities and did not show significant associations with clinicopathological parameters or prognosis; (4) Conclusion: High leptinR is a promising biomarker for favourable tumour outcome in renal cell carcinoma and vulvar carcinoma.

Coalbed Methane(CBM) production enhancement for single wells is a big problem to CBM industrialization. Low production is due to insufficient gas generation by thermogenic. Luckily, Biogenic gas was found in many areas and its supply is assumed to improve coalbed methane production. Therefore, microbial simulation experiment will demonstrate the effectiveness of the assumption. From microbial simulation experiment on different coal ranks, it is found that microbes can use coals to produce biogas under laboratory conditions. With different temperatures for different experiments, it turns out that the gas production at 35 ℃ is greater than that at 15℃,indicating that 35℃ is more suitable for microbes to produce gas. According to quantitative experiments, adding exogenous nutrients or exogenous bacteria can improve CBM production. Moreover, the production enhancement ratio can reach up to 115% under the condition of adding exogenous bacterial species, while the ratio for adding nutrients can be up to 144%.

The author demonstrates a stable Lagrangian solid modeling method, tracking the interactions of solid mass particles rather than using a meshed grid. This numerical method avoids the problem of tensile instability often seen with smooth particle applied mechanics by having the solid particles apply stresses expected with Hooke's law, as opposed to using a smoothing function for neighboring solid particles. This method has been tested successfully with a bar in tension, compression, and shear, as well as a disk compressed into a flat plate, and the numerical model consistently matched the analytical Hooke's law as well as Hertz contact theory for all examples. The solid modeling numerical method was then built into a 2-D model of a pressure vessel, which was tested with liquid water particles under pressure and simulated with smoothed particle hydrodynamics. This simulation was stable, and demonstrated the feasibility of Lagrangian specification modeling for fluid–solid interactions.

Flexible energy storage devices, such as solid-state supercapacitors, are becoming increasingly attractive due to their characteristics of high electrochemical performance, reliability, light weight, flexibility, absence of electrolyte leakage, high power density, and long lifetime. For the optimization of the solid-state symmetrical supercapacitor proposed in this work, it was employed in sodium and lithium form Aquivion electrolyte membrane, which serves as the separator and electrolyte. As electrode materials, carbon xerogels, synthesized by microwave-assisted sol-gel methodology, with designed and controlled properties were obtained. Commercial activated carbon (YP-50F, 'Kuraray Europe' GmbH) was used for comparison. Specifically, the developed solid-state symmetrical supercapacitors deliver sufficient high specific capacitances of 105−110 F g−1 at 0.2 A g−1, along with an energy density of 4.5 Wh kg−1 at 300 W kg−1, and in a voltage window of 0-1.2 V in an aqueous environments, also demonstrating excellent cycling stability up to 10,000 charge/discharge cycles. These results can demonstrate the potential applications of carbon xerogel as an active electrode material and cation exchange membrane as the electrolyte in the development of solid-state supercapacitor devices

Li₇La₃Zr₂O₁₂Solid-state reaction was used for Li₇La₃Zr₂O₁₂ material synthesis from Li₂CO₃, La₂O₃ and ZrO₂ powders. Phase investigation by XRD, SEM and EDS methods of Li₇La₃Zr₂O₁₂ were carried out. The molar heat capacity of Li₇La₃Zr₂O₁₂ at constant pressure in the temperature range 298-800 K should be calculated as Cp,m = 518.135+0.599 × T - 8.339 × T−2, where T is absolute temperature, . Thermodynamic characteristics of Li₇La₃Zr₂O₁₂ were determined as next: entropy S0298 = 362.3 J mol-1 K-1, molar enthalpy of dissolution ΔdHLlZO = ˗ 1471.73 ± 29.39 kJ mol−1, the standard enthalpy of formation from elements ΔfH0 = ˗ 9327.65 ± 7.9 kJ mol−1, the standard Gibbs free energy of formation ∆f G0298 = ˗9435.6 kJ mol-1.

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

The aim of this study was to quantify methane (CH4) emissions from dairy cows during milking by maximum amplitude of eructation peaks and compare estimates with other metrics for CH4 emissions. Spot measurements of CH4 and carbon dioxide (CO2) emissions were recorded for at least 7 days of continuous sampling using an infrared gas analyser in a robotic milking station whilst cows were milked. Concentrations of CH4 and CO2 were measured at 1 second intervals. A total of 105,701 CH4 spot measurements were obtained from 2,206 dairy cows on 18 farms. Methane emissions per individual cow were quantified by maximum amplitude of eructation peaks, average area under eructation peaks (integral of eructation), average concentration during milking and ratio of CH4 to CO2 concentration. There was a high correlation (r = 0.71) between CH4 emissions quantified by maximum amplitude and integral of eructation peaks. The correlation between maximum amplitude and average CH4 concentration was low, and there was no correlation between maximum amplitude and ratio of CH4 to CO2. As both approaches identify and extract eructation peaks to quantify enteric CH4 emissions, the substantial association between maximum amplitude and eructation integral was expected.

Owing to the growing concerns due to dwindling fossil fuel reserves, increasing energy demand and climate emergency, it is imperative to develop and deploy sustainable energy technologies to ensure future energy supply as well as transition to the net zero world. In this context, there is great potential in the biorefinery concept for supplying drop in biofuels in the form of biodiesel. Biodiesel as a fuel can certainly bridge the gap where electrification or the use of hydrogen is not feasible, for instance heavy vehicles, farm and marine transportation sector. However, biodiesel industry also leads to formation of large amount of crude glycerol as the byproduct. Crude glycerol due to presence of several impurities may not be a suitable feedstock for all high value products derived from glycerol but fits well with glycerol esterification for producing glycerol acetins, which have numerous applications. This review critically looks at the processes using nanostructured solid/liquid acid catalysts for glycerol esterification including the economic viability of the scale up.

The primary goal of this review is to provide a comprehensive overview of the state-of-the-art in solid-state batteries (SSBs), with a focus on recent advancements in solid electrolytes and anodes. The paper begins with a background on the evolution from liquid electrolyte lithium-ion batteries to advanced SSBs, highlighting their enhanced safety and energy density. It addresses the increasing demand for efficient, safe energy storage in applications like electric vehicles and portable electronics. A major part of the paper analyzes solid electrolytes, key to SSB technology. It classifies solid electrolytes as polymer-based, oxide-based, and sulfide-based, discussing their distinct properties and application suitability. The review also covers advancements in anode materials for SSBs, exploring materials like lithium metal, silicon, and intermetallic compounds, focusing on their capacity, durability, and compatibility with solid electrolytes. It addresses challenges in integrating these anode materials, like interface stability and lithium dendrite growth. This review includes a discussion on the latest analytical techniques, experimental studies, and computational models to understand and improve the anode-solid electrolyte interface. These are crucial for tackling interfacial resistance and ensuring SSBs' long-term stability and efficiency. Concluding, the paper suggests future research and development directions, highlighting SSBs' potential in revolutionizing energy storage technologies. This review serves as a vital resource for academics, researchers, and industry professionals in advanced battery technology development. It offers a detailed overview of materials and technologies shaping SSBs' future, providing insights into current challenges and potential solutions in this rapidly evolving field.

In the framework of fully vertical GaN-on-Silicon device technology development, we report on the optimization of non-alloyed ohmic contacts on the N-polar n+ doped GaN face backside layer. This evaluation is made possible by using patterned TLMs (Transmission Line Model) through direct laser writing lithography after locally removing the substrate and buffer layers in order to access the n+ doped backside layer. As deposited non-alloyed metal stack on top of N-polar orientation GaN layer after buffer layers removal results in poor ohmic contact quality. To significantly reduce the related contact resistances, an HCl treatment is applied prior to metallization under various time and temperature conditions. A 3-minutes HCl treatment at 70°C is found to be the optimum condition to achieve thermally stable high ohmic contact quality. To further understand the impact of the wet treatment, SEM (Scanning Electron Microscopy) and XPS (X-ray Photoelectron Spectroscopy) analysis were performed. XPS revealed a decrease in Ga-O concentration after applying the treatment, reflecting the higher oxidation susceptibility of the N-polar face compared to the Ga-polar face, which was used as a reference. SEM images of the treated samples show the formation of pyramids on the N-face after HCl treatment, suggesting specific wet etching planes of the GaN crystal from the N-face. The size of the pyramids is time-dependent; thus, increasing the treatment duration results in larger pyramids, explaining the degradation of ohmic contact quality after prolonged high temperature HCl treatment.

The aim of this study was to investigate the relationship between postprandial glycemic levels based on flash-monitoring and the production of intestinal hydrogen (H2) and methane (CH4) gases based on measurement of the amount of these gases in exhaled air. We studied 14 subjects with type 2 diabetes mellitus (T2DM) and 10 individuals without diabetes (control) with 3 food-load tests with simultaneous determination of gases in exhaled air and assessment of glucose levels. In 15.4% of patients with T2DM, there was a non-significant increase in exhaled H2. How-ever, all subjects in the control group had significant increase in exhaled H2. Moreover, the level of H2 in exhaled breathafter food load in patients with T2DM was lower than in normoglycemic subjects. Also, in normoglycemic subjects there was an inverse correlation between maximum glucose rise and maximum H2 in exhaled air after food load. At the same time in patients with T2DM the level of CH4 in exhaled air directly correlated with the parameters of postprandial glycemia in the test with lactulose. Confirmation of a causal relationship between decreased H2 production, increased intestinal CH4 production, and more severe postprandial glycemia may identify new therapeutic targets in the correction of postprandial glycemia in patients with T2DM.

This study investigates the use of Au-doped Pd anodic electrocatalysts on ATO support for the conversion of methane to methanol. The study involves cyclic voltammetry, in-situ Raman spectra, polarization curves, and FTIR analysis to determine the optimal composition of gold and palladium for enhancing the conversion process. The results demonstrate the potential for utilizing methane as a feedstock for producing sustainable energy sources. Pd75Au25/ATO electrode exhibited the highest OCP value, and Pd50Au50/ATO had the highest methanol production value at a potential of 0.05 V. Therefore, it can be concluded that an optimal composition of gold and palladium exists to enhance the conversion of methane to methanol. The findings contribute to the development of efficient and sustainable energy sources, highlighting the importance of exploring alternative ways to produce methanol.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2&gt;CH4&gt;N2.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P &lt; 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P &lt;0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

The Signal Transducer and Activator of Transcription (STAT)3 and 5 are activated by many cytokine receptors to regulate specific gene expression and mitochondrial functions. Their role in cancer is largely context dependent as they can both act as oncogenes and tumor suppressors. We review here the role of STAT3/5 activation in solid cancers and summarize their association to survival in cancer patients. The molecular mechanisms that underpins the oncogenic activity of STAT3/5 signaling includes the regulation of genes that control cell cycle, cell death, inflammation and stemness. In addition, STAT3 mitochondrial functions are required for transformation. On the other hand, several tumor suppressor pathways act on or are activated by STAT3/5 signaling including the p19ARF/p53 pathway, tyrosine phosphatases, suppressor of cytokine signaling 1 and 3, the sumo ligase PIAS3, the E3 ubiquitin ligase TMF/ARA160 and the miRNAs miR-124 and miR-1181. Cancer mutations and epigenetic alterations may alter the balance between pro-oncogenic and tumor suppressor activities associated to STAT3/5 signaling explaining their context dependent association to tumor progression both in human cancers and animal models.

The mechanical pre-treatment constitutes an unavoidable pre-step prior to biofuels conversion. As the cost of this step is often underestimated, recently researchers have striven to identify and characterize the mechanical pre-treatment effects in terms of post-treatment physical characterization, derived improvement of enzymatic digestibility, and output yields. The status of existing mechanical pre-treatment techniques is reviewed by substrate’s typology for lignocellulose biomass, focusing on comminution techniques. Emphasis has been dedicated to the particle size achieved after treatment, crystallinity breakage and eventual inhibitory phenomena deriving from the application of particle size reduction, which are analysed and discussed.

Biogenic emissions affect the urban air quality as they are ozone and SOA precursors and should be taken into account when applying photochemical pollution models. The present study presents an estimation of the magnitude of Non-Methane Volatile Organic Compounds emissions (NMVOCs) emitted by vegetation over Greece. The methodology is based on computation performed with the aid of a Geographic Information System (GIS) and theoretical equations in order to develop an emission inventory on a 6x6 spatial resolution, in a temporal resolution of 1hr covering one year (2016). For this purpose, a variety of input data was used: improved satellite land-use data, land-use specific emission potentials, foliar biomass densities, temperature and solar radiation data. Hourly, daily and annual isoprene, monoterpenes and other volatile organic compounds (OVOCs) were estimated. In the area under study, the annual biogenic emissions were estimated up to 472 kt, consisting of 46.6% isoprene, 28% monoterpenes and 25.4% OVOCs. Results delineate an annual cycle with increasing values from March to April, while maximum emissions were observed from May to September, followed by a decrease from October to January.

This comprehensive review has systematically examined the use of heterogeneous solid acid catalysts in the production of biodiesel from wastewater-derived sludge by using the PRISMA methodology. The manuscript highlighted the composition and characteristics of wastewater-derived sludge, presenting both the opportunities and challenges associated with its use as a feedstock for biodiesel production. Various types of catalysts were dis-cussed, with a detailed exploration of heterogeneous solid acid catalysts, including zeolites, hetero-polyacid (HPA), mixed metal oxides, and sulphonic acid group catalysts. The advantages and limitations of these catalysts were critically analyzed, providing a balanced view of their potential in industrial applications. The application section delved into the catalytic transesterification reaction, mechanisms of biodiesel production, and the effects of catalyst loading on yield. Performance metrics such as catalytic activity, stability, recyclability, cost-effectiveness, and environ-mental impact were thoroughly evaluated, offering a clear understanding of the efficacy of these catalysts. Synthesis and characterization techniques were also reviewed, shedding light on the latest preparation methods and characterization techniques. Recent advances in catalyst development were presented, showcasing the innovative strides made in enhancing catalyst performance. The environmental and economic implications of using solid acid catalysts for bio-diesel production were assessed, emphasizing the importance of sustainability and economic viability.

In this study, robust composite solid electrolytes were developed and employed them to enhance the performance of Li-metal batteries significantly. The robust composite solid electrolytes are composed of a soft polymer, poly(ethylene oxide), a Li salt, bis(trifluoromethanesulfonyl)imide (LiTFSI), and super ionic conductive ceramic fillers such as Li1.5Al0.5Ti1.5(PO4)3 (LATP), and Li6.4La3Zr1.4Ta0.6O12 (LLZTO). The main goal of this study is to enhance the electrochemical stability and ionic conductivity. The ionic conductivities of the composite solid electrolytes were found to be 2.08 × 10-4 and 1.64 × 10-4 S cm-1 with the introduction of LATP and LLZTO fillers, respectively. The results prove that the fabricated solid electrolyte was electrochemical stable at voltage exceeding 4.25 V vs. Li/Li+. The internal resistance of the solid electrolyte significantly reduced as compare to gel electrolyte. This reduction can be attributed owing to the alleviation of bulk electrolyte, charge-transfer, and interfacial electrolyte/electrode impedance. When LiFePO4 cathode sheets are coated with a composite solid electrolyte containing LATP powders, the resulting Li-metal battery displays high capacity at 5 C (with a capacity retention of 65.2% compared to the original capacity at 0.2 C) as well as superior cyclic stability and excellent Coulombic efficiency (&gt; 99.5%, over 200 cycles). These results confirm that the composite solid electrolyte acts as a protective layer which have ability to prevent the growth of Li dendrites. Consequently, the fabricated electrolyte configuration can be engineered to enable high energy/power density and electrochemical stable cyclability in Li-metal batteries.

Methane is a greenhouse gas and identified as a key driver of near-term climate change. Bottom-up approaches estimate annual methane loss from US natural gas production and transport at 6 Tg, but recent studies suggest this may be an underestimate. To investigate this possibility, an equipment-based emissions inventory, using EPA emission factors, was developed to calculate methane emissions from oil and gas operations in the Delaware Basin, USA. Emission factors and activity data were then updated using contemporary and region-specific measurement data. The original inventory estimated emissions at 315 Gg CH4 y-1 (gas production-normalized rate of 0.6% loss), while the updated inventory estimated emissions of 1,500 Gg CH4 y-1 (2.8% loss). The largest changes resulted from large fugitive emissions from oil production (+430 Gg CH4 y-1), updating maintenance activity emissions (+214 Gg CH4 y-1), considering flaring inefficiency (+174 Gg CH4 y-1), and the inclusion of associated gas venting (+136 Gg CH4 y-1). This study suggests that a systematic underestimate probably exists in current bottom-up inventories and identifies sources currently missing or may be incorrect. We also strongly recommend that emission factors should be validated through direct comparison against measurement campaigns that include long-tail distributions typical of oil and gas activities.

To estimate The potential inventory of natural gas hydrates in the Levant Basin we correlated the gas hydrate stability zone (GHSZ), modeled with locally estimated thermodynamic parameters, with seismic indicators of gas. Compilation of oceanographic measurements define the deep-water temperature and salinity to 13.8°C and 38.8‰ respectively, predicting the top GHSZ at a water depth of 1250±5 m. Assuming beneath the seafloor a hydrostatic pore-pressure, the water body salinity, and geothermal gradients ranging between 20 to 28.5°C/km, yields a useful first-order base-GHSZ approximation. Our model predicts that the entire northwestern half of the Levant Basin lies within the GHSZ, with a median thickness of ~150 m. High amplitude seismic reflectivity (HASR) imaged on an extensive 3D seismic dataset, consistently correlates with verified active seafloor gas seepage and is pervasively distributed across the deep-sea fan of the Nile within the Levant. Two main trends observed for the distribution of HASR are suggested to represent: (1) shallow gas and possibly hydrates, within buried channel-lobe systems 25 to 100 m beneath the seafloor; and (2) a regionally discontinuous bottom simulating reflection (BSR) broadly matching the modeled base GHSZ. We therefore estimate the potential methane hydrates reserve within the Levant Basin at ~4 Tcf.

More than 700 anthocyanins are described so far, and many different sources are rich in these natural pigments. During the last few years, researchers have been focusing of strategies to recover and purify anthocyanins, from simple liquid-liquid extractions to more advanced supercritical CO2 extractions, however, with such a huge number of different sources, it’s extremely hard to get a simple and fast methodology that fits several sources, not only by the structural nature of the anthocyanins but also by the presence of specific groups of natural compounds. Using simple methodologies like solid-phase extraction resins represents a powerful economical and efficiency strategy. In this work, we tested several sources of structurally distinct anthocyanins, including purple basil, purple cabbage, purple sweet potato, butterfly pea flower, cornflower and wild pansy, in different resins to assess their efficiency in the obtention of anthocyanin-pure extracts. The results showed us that the combination of oasis HLB® resin followed by a cation-exchange SPE with DSC-MCAX® resulted in high-purity anthocyanin extracts for all the cases.

Quantifying methane emissions is essential for meeting near-term climate goals and typically done using methane concentrations measured downwind of the source. One major source of methane that is important to observe and promptly remediate is fugitive emissions from oil and gas productions sites but installing methane sensors at the thousands of sites within a production basin is expensive. In recent years, relatively inexpensive metal oxide sensors have been used to measure methane concentrations at production sites. Current methods used to calibrate metal oxide sensors have been shown to have significant shortcomings resulting in limited confidence in methane concentrations generated by these sensors. To address this, we investigate using machine learning (ML) to generate a model that converts metal oxide sensor output to methane mixing ratios. To generate test data, two metal oxide sensors, TGS2600 and TGS2611, were collocated with a trace methane analyzer downwind of controlled methane releases. Over the duration of the measurements, the trace gas analyzer’s average methane mixing ratio was 2.40 ppm with a maximum of 147.6 ppm. The average calculated methane mixing ratios for the TGS2600 and TGS2611 using the ML algorithm were 2.42 ppm and 2.40 ppm with maximum values of 105.9 ppm and 106.3 ppm, respectively. A comparison of histograms generated using the analyzer and metal oxide sensors mixing ratios show overlap coefficients of 0.95 and 0.94 for the TGS2600 and TGS2611, respectively. Overall, our results showed there was a good agreement between the ML derived metal oxide sensors’ mixing ratios and those generated using the more accurate trace gas analyzer. This suggests that the response of lower-cost sensors calibrated using ML could be used to generate mixing ratios with precision and accuracy comparable to higher price trace methane analyzers. This would improve confidence in low-cost sensors’ response, reduce the cost of sensor deploying, and allow for timely and accurate tracking of methane emissions.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

The air in subterranean karst cavities is often depleted in methane (CH₄) relative to the atmosphere. Karst is considered a potential sink for the atmospheric greenhouse gas CH₄ because its subsurface drainage networks and solution-enlarged fractures facilitate atmospheric exchange. Karst landscapes cover about 14% of earth’s continental surface, but observations of CH₄ concentrations in cave air are limited to localized studies in Gibraltar, Spain, Indiana (USA), Vietnam, Australia, and by incomplete isotopic data. To test if karst is acting as a global CH₄ sink, we measured the CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values of cave air from 33 caves in the USA and three caves in New Zealand. We also measured CO₂ concentrations, δ¹³C_CO2, and radon (Rn) concentrations to support CH₄ data interpretation by assessing cave air residence times and mixing processes. Among these caves, 35 exhibited subatmospheric CH₄ concentrations in at least one location compared to their local atmospheric backgrounds. CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values suggest that microbial methanotrophy within caves is the primary CH₄ consumption mechanism. Only 5 locations from 3 caves showed elevated CH₄ concentrations compared to the atmospheric background and could be ascribed to local CH₄ sources from sewage and outgassing swamp water. Several associated δ¹³C_CH4 and δ²H_CH4 values point to carbonate reduction and acetate fermentation as biochemical pathways of limited methanogenesis in karst environments and suggest that these pathways occur in the environment over large spatial scales. Our data show that karst environments function as a global CH₄ sink.

NaClO3 and NaBrO3 are believed to form a complete solid solution from RT to fusion. The unique solid phase can thus be written: NaClO3 (1-x)-NaBrO3 (x) with: 0 ≤ x ≤ 1. This study shows that at high temperature this statement might be valid. Nevertheless, up to 50°C and probably up to 160°C and even higher temperature, this is not true when the system is in thermodynamic equilibrium. A large miscibility gap exists at room temperature (RT). This gap could be reduced up to a complete disappearance by fast crystallization, for instance by spray-drying. The necessary conditions to access to equilibrium including homochirality are also discussed.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

The oxidative coupling of methane (OCM) to produce ethane and ethylene (C2 compounds) as platform chemicals involves complex chemistry with reactions both in the gas phase and on the catalyst surface, resulting in a distribution of products at the expense of C2 selectivity. This work uses experimental data from a variety of mixed metal oxides on supports at different reaction conditions (temperature, contact time, and reactant flow rates) to train a random forest regressor that predicts methane conversion and C2 selectivity (key performance indicators (KPIs)), and deploys it to locate optimal conditions that maximize C2 yield for a catalyst. Investigating the regressor interpretability via feature importance reveals that the choice of metals and support are crucial to C2 selectivity predictions, while the predictions of methane conversion are driven by the reaction conditions. The machine learning (ML) regressor is used as a surrogate to develop performance curves for each of the catalysts via a multi-objective optimization routine that seeks to maximize the KPIs in the decision space of reaction conditions, is seen to locate optimal conditions at which the maximum C2 yields for catalysts are predicted to be 15%, higher on average. Analyzing the catalysts in the space of their performance curves with respect to a popular OCM catalyst, Mn-Na2WO4/SiO2, reveals distinct patterns based on intrinsic properties of metals and supports. Further, the decision space with catalyst descriptors and reaction conditions is optimized for high C2 yields using the ML surrogate, in a static multi-objective optimization routine, and an adaptive Bayesian routine, where the latter was found to have a wider field focus in proposing catalyst formulations and conditions. Transition metal oxides on a variety of supports were proposed but not their lanthanide oxide counterparts.

Methane (CH4), produced endogenously in animals and plants, has recently been suggested to play a role in cellular physiology, potentially influencing the signaling pathways and regulatory mechanisms involved in nitrosative and oxidative stress responses. In addition, it has been proposed that supplementation of CH4 to organisms may be beneficial for the treatment of several diseases, including ischemia, reperfusion injury, and inflammation. However, it is still unclear if and how CH4 is produced in mammalian cells without the help of microorganisms, and how CH4 might be involved in physiological processes in humans. In this study, we provide first proof of the principle that CH4 is formed non-microbially in the human body by applying isotopically labeled methylated sulfur compounds, such as dimethyl sulfoxide (DMSO) and methionine, as carbon precursors to confirm cellular CH4 formation. A volunteer applied isotopically labeled (2H and 13C) DMSO on the skin, orally, and to blood samples. Monitoring of stable isotope values of CH4 convincingly showed the conversion of the methyl groups, as isotopically labeled CH4 was formed during all experiments. Based on these results, we consider several hypotheses about endogenously formed CH4 in humans, including physiological aspects and stress responses involving reactive oxygen species (ROS). While further and broader validation studies are needed, the results may unambiguously serve as a proof of concept for the endoge-nous formation of CH4 in humans by a radical-driven process. Furthermore, these results might encourage follow up studies to decipher the potential physiological role of CH4 and its bioactiv-ity in humans in more detail. Of particular importance is the potential to monitor CH4 as an ox-idative stress biomarker if the observed large variability of CH4 in breath air is an indicator for physiological stress responses and immune reactions. Finally, the potential role of DMSO as a radical scavenger to counteract oxidative stress caused by ROS might be considered in the health sciences. DMSO has already been investigated for many years, but its potential positive role for medical use remained highly uncertain.

The garnet Li₇La₃Zr₂O₁₂ (LLZO) has been widely investigated because of its high conductivity, wide electrochemical window and chemical stability to lithium metal. However, the usual preparation process of LLZO requires a long time of high-temperature sintering and a lot of mother powders against the lithium evaporation. The submicron Li₆.6La₃Zr₁.6Nb₀.4O₁₂ (LLZNO) powders are prepared by conventional solid-state reaction method and attrition milling process, which are stable cubic phase and have high sintering activity, and Li stoichiometric LLZNO ceramics are obtained by sintering at a relative lower temperature or for a short time by using these powders which are difficult to control under high sintering temperature and long sintering time. The particle size distribution, phase structure, microstructure, distribution of element, total ionic conductivity, relative density and activation energy of submicron LLZNO powders and LLZNO ceramics are tested and analyzed by laser diffraction particle size analyzer, XRD, SEM, EIS and Archimedean method. The total ionic conductivity of sample sintered at 1200 °C for 30 min is 5.09 × 10-4 S·cm-1, the activation energy is 0.311 eV, and the relative density is 87.3%, and sintered at 1150 °C for 60 min total ionic conductivity is 3.49 × 10-4 S·cm-1, the activation energy is 0.316 eV, and the relative density is 90.4%. At the same time, all-solid-state batteries are assembled with LiMn₂O₄ as positive electrode and submicron LLZNO powders as solid state electrolyte. After 50 cycles, the discharge specific capacity is 105.5 mAh/g and the columbic efficiency is above 95%.

In this paper, four lithological parameters, i.e. thermal conductivity, particle size, porosity and saturation, are investigated by combining experimental observations with numerical simulations to study the influence laws and mechanisms of action on the combustion process of methane hydrate sediments. The variation of combustion characteristics parameters such as flame height, effective combustion ratio and dimensionless discharge water mass with the lithological parameters are studied. In addition, the combustion mechanism of lithologic parameters on methane hydrate deposits is revealed. Combining the experimental results and simulation calculations, to optimize the combustion of methane hydrate sediments, it is recommended to use methane hydrate sediment samples with high saturation and low thermal conductivity, while the oxidant concentration and porosity of methane hydrate sediment samples should be increased.

Researchers have been exploring seaweed to reduce methane (CH4) emissions from livestock. This study aimed to investigate the potential of a red alga, Bonnemaisonia hamifera, as an alternative to mitigate CH4 emissions. B. hamifera, harvested from the West coast of Sweden, was used in an in vitro experiment using a fully automated gas production system. The experiment was a ran-domized complete block design consisting of a 48-h incubation that included a control (grass si-lage) and B. hamifera inclusions at 2.5%, 5.0% and 7.5% of grass silage OM mixed with buffered rumen fluid. Predicted in vivo CH4 production and total gas production were estimated by ap-plying a set of models to the gas production data and in vitro fermentation characteristics were evaluated. The results demonstrated that the inclusion of B. hamifera reduced (P = 0.01) predicted in vivo CH4 and total gas production, and total gas production linearly decreased (P = 0.03) with higher inclusion of B. hamifera. The molar proportion of propionate increased (P = 0.03) while isovalerate decreased (P = 0.04) with inclusion of B. hamifera. There was a tendency for increased (0.06 ≤ P ≤ 0.10) total volatile fatty acid production, as well as lower proportions of butyrate, isobutyrate, and 2-methylbutyrate. Chemical analyses revealed that B. hamifera had moderate concentrations of polyphenols. The iodine content was low and there was no detectable bromo-form, suggesting quality advantages over Asparagopsis taxiformis. Additionally, B. hamifera exhib-ited antioxidant activity comparable to the positive control Resveratrol. The findings of this study indicated that B. hamifera harvested from temperate waters in Sweden possesses capacity to mitigate CH4 in vitro.

The direct methane to methanol (MTM) oxidation is a grand challenge in catalysis, with profound economical implications for the modern chemical industry. Bioinspired metal-organic frameworks (MOFs) with active iron and copper sites have been emerging very recently as innovative catalytic platforms to accomplish the MTM conversion under mild conditions. This review discusses the current state of the art regarding the application of MOFs with iron and copper catalytic centers to perform the MTM reaction, with a focus on the diverse spectroscopic techniques used to unveil the electronic and structural properties of the MOF catalysts at a microscopic level. We explore the synthetic strategies employed to incorporate iron and copper sites into different MOF topologies, the efficiency and selectivity of the iron- and copper-bearing MOF catalysts, and the ensuing MTM reaction mechanisms proposed on the basis of spectroscopic characterization supported by theory. In particular, we evidence how the combination of complementary spectroscopic tools probing different regions of the electromagnetic spectrum is particularly useful to reach a satisfactory understanding of the key reaction pathways and intermediates. Finally, we provide a critical perspective on future directions to advance the use of MOFs to accomplish the MTM reaction.

Methane (CH4) emissions from agricultural sources make a significant contribution to the total anthropogenic greenhouse gas emissions that contribute to climate change. According to the International Panel on Climate Change (IPCC) guidelines for calculating greenhouse gas emissions, agriculture is responsible for approximately 10% of total CH4 emissions from anthropogenic sources. CH4 is mainly emitted from livestock farming, especially from cattle production during enteric fermentation and from manure. The article describes the results of multivariate statistical analyzes carried out on data collected in 1961–2020 based on the data for 30 countries with the largest cattle population. The trends of temporal changes in cattle population were evaluated and groups of countries with similar patterns in the study period were distinguished. Variables which are correlated with changes in the number of cattle were indicated. Forecasts of cattle population and CH4 emission related to cattle for the coming years are presented.

The conversion of methane into chemicals is of interest to achieve a decarbonized future. Fuel cells are electrochemical devices commonly used to obtain electrical energy, but can be utilized either for chemicals production or both energy and chemicals cogeneration. In this work, the partial oxidation of methane in fuel cells for electricity generation and valuable chemicals production at the same time is reviewed. For this purpose, different types of methane-fed fuel cells, both low temperature fuel cells, such as PEMFCs and AAEMFCs, and high temperature fuel cells, such as SOFCs, have been used. Also if few works have been devoted to this topic, the promising results drive the development of fuel cells using methane as the source for the cogeneration of power and valuable chemicals.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

Due to the rapid development of nanotechnologies, materials, in particular , solid dispersions (SDs), which are actively introduced into the life of modern man, have been obtained. Special progress in this area is observed in industry and medicine. The use of SDs in agriculture is lagging far behind, despite the growing number of scientific papers on this topic. At the same time, the prospects for the introduction of SDs in the agro-industrial complex are obvious. The review presents the results of research on the development of innovative preparations based on SD to protect plants from diseases and pests of cultivated plants, as well as parasiticides to protect animal health based on modern achievements of nanotechnology. One of these technologies is the methods of mechanochemistry, which improve the properties of poorly soluble biologically active substances by their joint mechanical treatment with water-soluble polymers and auxiliary substances.

Personal Information Management Systems (PIMS) are acquiring a prominent role in the data economy by promoting services that help individuals to have more control over the processing of their personal data, in line with the European data protection law. One of the highlighted solutions in this area is Solid, a new protocol that is decentralizing the storage of data, through the usage of interoperable Web standards and semantic vocabularies, to empower its users to have more control over the processing of data by agents and applications. However, to fulfill this vision and gather widespread adoption, Solid needs to be aligned with the law governing the processing of personal data in Europe, the main piece of legislation being the General Data Protection Regulation (GDPR). To assist with this process, we analyze the current efforts to introduce a policy layer in the Solid ecosystem, in particular, related to the challenge of obtaining consent for processing personal data, focusing on the GDPR. Furthermore, we investigate if, in the context of using personal data for biomedical research, consent can be expressed in advance, discuss the conditions for valid consent and how it can be obtained in this decentralized setting, namely through the matching of privacy preferences, set by the user, with requests for data and whether this can signify informed consent. Finally, we discuss the technical challenges of an implementation that caters to the previously-identified legal requirements.

Cities are important sources of anthropogenic methane emissions. Municipal governments can play a role in reducing those emissions to support climate change mitigation, but they need information on the rate of emissions to context mitigation actions and track progress. Here, we examine the application of satellite data from the TROPOspheric Monitoring Instrument (TROPOMI) to estimate city-level methane emissions rates in a case study of the City of Calgary, Alberta, Canada. While satellites are touted as a global methane monitoring system, we found limited observational coverage over Calgary that precluded the reliability of measurement-based models to track the annual emissions. In this work, we integrated valid observations over three years (2020-22) and used mass balance modeling to derive a long-term averaged emission estimate. The column-averaged dry-air mole fraction (XCH4) enhancement over Calgary was small, 4.7 ppb, but within the city boundary, we identified local hot spots in the vicinity of known sources (wastewater treatment facility and landfills). The city-scale emissions estimate from mass balance was 215.4 ± 132.8 t/d CH4. This estimate is approximately four- and six-times larger than estimates from Canada's gridded national inventory report of anthropogenic CH4 emissions and the Emissions Database for Global Atmospheric Research (EDGAR v8.0), respectively. Valid observations are more common in warmer months and occur during a narrow daily overpass timeslot over Calgary – these effects may bias the emissions estimate. Overall, the findings from this case study highlight the challenge of deriving routine (sub-annual to annual) satellite-based estimates of city-scale methane emissions in similar geographic settings and suggest that more granular emissions inventories are needed to improve methane reporting.

Prevention of infections is crucial in solid organ transplant (SOT) candidates and recipients. These pa-tients are exposed to an increased infectious risk due to previous organ insufficiency and to pharmaco-logic immunosuppression. Besides infectious-related morbidity and mortality, this vulnerable group of patients is also exposed to the risk of acute decompensation and organ rejection or failure in the pre- and post-transplant period respectively, since antimicrobial treatments are less effective than in the immunocompetent patients. Vaccination represents a major preventive measure against specific infec-tious risks in this population but as responses to vaccines are reduced, especially in the early post-transplant period or after treatment for rejection, an optimal vaccination status should be obtained prior to transplantation whenever possible. This review reports the currently available data on the indications and modalities of vaccination in SOT adult candidates and recipients.

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

The aim of this paper is the presentation of an analytical model of insulator flashover and its application for air at atmospheric pressure and pressurized SF6. After a review of the main existing models in air and compressed gases, we develop a relationship of flashover voltage on the basis of an electrical equivalent circuit and the thermal properties of the discharge. The model includes the discharge resistance, the insulator impedance, and the gas interface impedance. The application of this model to a cylindrical resin-epoxy insulators in air medium and SF6 gas with different pressures gives results close to the experimental measurements.

: Sulfate presence is of great importance for anaerobic digestion as its addition can control the anaerobic microbial community. In this study, the effect of sulfuric acid addition on the perfor-mance of an UASB reactor fed with hydrolyzed starch was investigated. TOC, Fe and SO4-2 re-moval as well as the methane production were monitored under various COD/ SO4-2 ratios, HRTs and OLRs. When HRT was 16 hours and OLR equal to 2 g COD/LUASB-d the methane production was 0.24 L CH4/LUASB-day. After the sulfuric acid addition, TOC removal reached 95%. At HRT, OLR, and COD/ SO4-2 ratio equal to 16 hours, 2 g COD/ LUASB-d and 3.72 respectively, the methane production was 0.267 L CH4/LUASB-d. When the OLR was increased to 5.94 g COD/LUASB-d and COD/SO4-2 ratio was equal to 12.5, the methane production was 3 times higher (0.84 L CH4/LUASB-d) with a methane content in the produced biogas greater than 70%. 16s rRNA gene analysis demonstrated that after the sulfate addition, SRB were enriched and methane was mainly produced by Methanosaeta sp. This study indicates that appropriate sulfate concentrations in the feed in combination with the presence of iron in the UASB reactor lead to enhanced me-thane yields.

The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

This study numerically analyzed the effect of composition and temperature and oxygen concentration changes on the selfignition characteristics of n-heptane/methane blended fuels in order to cope with development of alternative fuels and international environmental regulations. CHEMKIN-PRO is used as the analysis program and the LLNL model is used as the reaction model. The numerical results revealed that on autoignition and ignition delay time were sensitive to changes in fuel composition and oxygen concentration. As the methane ratio increases, OH radicals causing ignition are delayed in generation and the concentration is lowered, thus longer the ignition timing. The oxygen concentration in the mixed fuels are changed to simulate the exhaust gas recirculation and a numerical analysis in then performed. As the oxygen concentration decreases, the ignition delay time longer because the nitrogen gas acts as a thermal load in the combustion chamber.

Migraine has a high prevalence worldwide and is one of the main disabling neurological diseases in individuals under the age of 50. In general, treatment includes the use of oral analgesics or non-steroidal anti-inflammatory drugs (NSAIDs) for mild attacks, and, for moderate or severe attacks, triptans or 5-hydroxytryptamine/serotonin (5-HT)1B/1D receptor agonists. However, the administration of antimigraine drugs in conventional oral pharmaceutical dosage forms is a challenge, since many molecules have difficulty crossing the blood-brain barrier (BBB) to reach the brain, which leads to bioavailability problems. Efforts have been made to find alternative delivery systems and/or routes for antimigraine drugs. In vivo studies have shown that it is possible to administer drugs directly into the brain via the intranasal (IN) or the nose-to-brain route, thus avoiding the need for the molecules to cross the BBB. In this field, the use of lipid nanoparticles, in particular solid lipid nanoparticles (SLN) and nanostructured lipid carriers (NLC), has shown promising results, since they have several advantages for drugs administered via the IN route, including increased absorption and reduced enzymatic degradation, improving bioavailability. Furthermore, SLN and NLC are capable of co-encapsulating drugs, promoting their simultaneous delivery to the site of therapeutic action, which can be a promising approach for the acute migraine treatment. This review highlights the potential of using SLN and NLC to improve the treatment of acute migraine via the nose-to-brain route. First sections describe the pathophysiology and the currently available pharmacological treatment for acute migraine, followed by an outline of the mechanisms underlying the nose-to-brain route. Afterwards, the main features of SLN and NLC and the most recent in vivo studies investigating the use of these nanoparticles for the treatment of acute migraine are presented.

Mere similar grades of same excipients manufactured by two different manufacturers often differ significantly that they even have an impact on the variations in final product or dosage form. Solid lipids are one of the most available options as matrix former in sustained drug delivery. Due to their chemical and physical complexity, lipids may exhibit a complex behaviour (i.e. melting crystallization and polymorphism). The aim of this study was to evaluate the physical and chemical properties of two Glyceryl Monostearate (GMS) lipids (Geleol from Gattefosse and Capmul GMS 50K from Abitec Corp. USA) and how these properties may affect during melt granulation process for sustained release applications. Thermal processing was applied on GMS samples to understand the polymorphic nature and suitability as meltable binders. Niacin was used as model drug. A thorough evaluation of GMS samples and sustained release tablets was undertaken using analytical techniques such as differential scanning calorimetry (DSC), X-ray diffraction (XRD). Moreover, melt viscosity study assisted to apprehend the behaviour of GMS samples in hot melt extrusion processing. Surface morphology of the drug and extruded granules examined via SEM and AFM revealed high level of surface interaction and dense structure of drug inside lipid matrix. The DSC and XRD study confirmed that Geleol could not withstand the heat treatment applied during thecontinuous melt granulation processing. The shifting of stable β form to an unstable α form in Geleol was detected. In the contrary case, Capmul GMS 50K was able to withstand the heat treatment supported by the applied analytical techniques. Nonetheless,both GMS samples perform differently in final dosage form. This change in stable β form to an unstable α form affected dissolution profiles at 3 months storage in accelerated condition. This study helped to interpret the complex solid-state behaviour of solid lipid extrudates with different compositions, in order to the simply and outline a suitable formulation strategy for the development of lipid-based oral dosage forms.

The increasing deployment of intermittent renewable energy sources necessitates effective methods for balancing the electrical grid to ensure stability and safety. Energy storage systems that can store excess electrical power during periods of low demand and release it during high demand are crucial for both short-term and long-term applications. Power-to-Gas is an innovative energy storage solution that converts surplus renewable electricity into gas fuels, such as hydrogen, which can be stored and used later. This hydrogen can serve multiple purposes, including energy storage and as fuel for transportation modes like cars, trams, trains, and buses. While most hydrogen today is derived from fossil fuels, solid-oxide electrolysis (SOE) offers a cleaner alternative by producing hydrogen without harmful emissions. SOE is also the most efficient method of electrolysis. This study aims to determine the operational parameters for an SOE system, including lower heating value (LHV)-based efficiency and total input power, using a mathematical model. Results are presented for three different operating temperatures and four different steam utilization ratios. The paper is structured as follows: the introduction provides the context and motivation for the study; the second section outlines the fundamentals of electrolysis and its various types; the third section delves into solid-oxide electrolysis and electrolyser systems; the fourth section describes the methodology, including the mathematical formulation and simulation software used; the fifth section presents the calculation results and conclusions; and the final section summarizes the findings.

Iron is a critical yet limited nutrient for microbial growth. To scavenge iron, most microbes produce siderophores—diverse small molecules with high iron affinities. Different siderophores are specifically recognized and uptaken by corresponding recognizers, enabling targeted interventions and intriguing cheater-producer dynamics. We propose constructing a comprehensive iron interaction network, or "iron-net," across the microbial world. Such a network offers the potential for precise manipulation of the microbiota, with conceivable applications in medicine, agriculture, and industry, as well as advancing microbial ecology and evolution theories. Previously, our successful construction of an iron-net in the Pseudomonas genus demonstrated the feasibility of co-evolution-inspired digital siderophore typing. Enhanced by machine learning techniques and expanding sequencing data, forging such an iron-net calls for multidisciplinary collaborations, and holds significant promise in addressing critical challenges in microbial communities.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.