The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

In this paper, the effect of multi-rotational speeds super-gravity field on the grain refinement and tensile properties of as-cast H13 steel were investigated systematically. The experimental results revealed that the as-cast grains of H13 steel can be significantly refined in multi-rotational speeds supergravity field. In conventional supergravity field, with the decrease of rotational radius, the secondary dendrite average spacing (SDAS) and the austenite grain average size (AGAS) increase, and the maximum values of SDAS and AGAS are 90 µm and 55 µm, respectively. while in multi-speeds supergravity fields, at the range of increasing rotational speeds, SDAS and AGAS decrease as the rotational radius decreases. In three-rotational speeds supergravity field, the maximum values of SDAS and AGAS are 80 µm and 50 µm. In five-rotational speeds supergravity field, the maximum values of SDAS and AGAS are reduced to 58 µm and 34 µm. Accordingly, both the tensile strength and the plasticity are enhanced with the increasing the number of rotational speeds in supergravity field, especially for the inner position of supergravity sample. The ultimate tensile strengths at outer, middle, and inner positions of H13 steel solidified in conventional supergravity field are 1445 MPa, 1378 MPa, and 1023 MPa, corresponding elongations of 2%, 1.5%, and 0.5%, while in the five-rotational speeds supergravity field, they are 1408 MPa, 1443 MPa, and 1453 MPa, corresponding elongations of 1.8%, 3.9%, and 2.2%. The mechanism for the grain refinement is that multi-speeds super-gravity can reduce the critical nucleation work of austenite, and the tangential force produced by changing the rotational speeds breaks dendrites at the solidification front, refining solidification structure.

The effects of chemical composition and solidification rate on the solidification behavior of high-Cr white irons were investigated through directional solidification. Increasing the solidi-fication rate in hypoeutectic alloys caused the finer dendrite arm spacing as expected. The eutec-tic structure which formed in the interdendritic region comprised of M7C3 and austenite, how-ever, secondary dendrite arms of hypoeutectic alloys contained a few M7C3 particles that solidi-fied prior to the eutectic structure. The transition from cellular to dendritic solidification oc-curred at a solidification rate between 50 µm/s and 100 µm/s in a near eutectic alloy. In the near eutectic alloy with cellular solidification, a directionally arrayed in-situ composite of M7C3/austenite formed within the cell. Speckle-like feature appeared in the intercellular region due to M23C6 carbide precipitation during subsequent cooling after freezing. Like dendrite arm spacing in hypoeutectic alloys, the inter-speckle spacing and the inter-fibre spacing became finer with increasing solidification rate in the cellular solidification range.

Sustainable development of our society demands recycling of metallic wastes which may contain a variety of metallic impurities. Thus, it is desirable to develop a ‘universal’ structure, such as an amorphous alloy tolerating high concentrations of metallic pollutants. We performed ab initio molecular dynamics simulations to manufacture a novel multicomponent amorphous alloy of twenty elements (20e-HEAA). Analysis reveals both topological and chemical compositional short-range ordering in the obtained 20e-HEAA and formation of B-B clusters. Electronic structure calculations reveal the metallic nature of the amorphous alloy with its Fermi level falling in a valley in the density of states. Moreover, the Zn 3d and Cd 4d electrons exhibit a localized nature and thus, should be excluded from the valence electron concentration (VEC) analysis in the study of high-entropy alloys. The information obtained here is helpful to get insight into multicomponent high entropy materials, especially multicomponent high-entropy amorphous alloys as potential circular metals.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

Among the thermophysical properties, the surface / interfacial tension, viscosity and density / molar volume of liquid alloys are the key properties for the modelling of microstructural evolution during solidification. Therefore, only reliable input data can yield accurate predictions preventing the error propagation in numerical simulations of solidification related processes. Due to experimental difficulties related to reactivity of metallic melts at high temperatures, the measured data are often unreliable or even lacking. The application of containerless processing techniques either leads to a significant improvement of the accuracy or makes the measurement possible at all. On the other side, accurate model predicted property values could be used to compensate the missing data; otherwise, the experimental data are useful for the validation of theoretical models. The choice of models is particularly important for the surface, transport and structural properties of liquid alloys representing the two limiting cases of mixing, i.e. ordered and phase separating alloy systems. To this aim, the thermophysical properties of the Fe-Si and Cu-Pb systems were analysed and the connections with the peculiarities of their mixing behaviours are highlighted.

Floral nectar is a key reward in Leguminosae despite the exceptional diversity of flowers in this family. The paper aims to summarize the available data on structure, ontogeny, regulation, and possible evolution of the leguminous floral nectaries. To date, detailed characterization of ultrastructure and mode of secretion is available only for a few representative of the family whereas the majority remains understudied from this perspective. In most cases, regardless of flower symmetry, nectaries are localized between stamens and a carpel. The nectar is usually exuded from modified stomata although the exact mode of secretion by specialized parenchyma may differ between taxa. The leguminous floral nectaries often have certain features of monosymmetry with preferentially abaxial development. Nectaries were independently lost in several lineages, and equally recurrent is the emergence of substitutive, i.e. evolutionary innovative, nectar-producing structures. Floral nectaries possess a certain degree of evolutionary inertia, i.e. they remain stable even in lineages in which flower morphology underwent significant changes compared with an ancestral plan, such as shifts in merism, symmetry, organ number and alike. Due to their evolutionary stability, floral nectaries are rarely used in taxonomy of Leguminosae.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

The article continues the search for a general law that describes the physical properties of a solid body, represented as a complex compound, through the physical properties of its elements. For a set of mixtures of metal oxides (actinide oxides), their melting or solidification temperatures were described in terms of the atomic weighted sum of the melting/solidification temperatures of these metals and molecular oxygen, multiplied by a variable which depending on the crystal structure and properties of melt of the compound and on the atomic numbers of the elements that make up the compound.

We summarise contributions made to the computational phase-field modelling of alloy solidification from the University of Leeds spoke of the LiME project. We begin with a general introduction to phase-field, and then reference the numerical issues that arise from solution of the model, before detailing each contribution to the modelling itself. These latter contributions range from controlling and developing interface-width independent modelling; controlling morphology in both single and multiphase settings; generalising from single to multi-phase models; and creating a thermodynamic consistent framework for modelling entropy flow and thereby postulate a temperature field consistent with the concepts of, and applicable in, multiphase and density-dependent settings.

Heat-treated aluminum-silicon (Al-Si)-based alloys have dominated the cast lightweight alloy industry for several decades. However, in the last decade, Al-Ce-based alloys have shown promise in replacing Al-Si alloys due to their ability to remove the need for costly heat treatments. Since the properties of Al-Ce alloys depend on the as-cast microstructure, it is important to characterize the solidification kinetics of these alloys. Therefore, this study focused on characterizing the solidification of a near eutectic Al-Ce alloy with additions of Ni and Mn. The alloy was cast in a wedge mold configuration, resulting in cooling rates between 0.18 and 14.27 °C/s. SEM coupled with EDS and DSC techniques characterized the evolution rate of solid phases. The SEM/EDS data revealed that an Al10CeMn2 phase is present at higher cooling rates. At lower cooling rates, near the center of the casting, a proeutectic Al23Ce4Ni6 phase was more present. It was observed that up to 2.6 at. % of Mn was dissolved in this proeutectic Al23Ce4Ni6 phase, thereby removing a large portion of the available Mn for forming the Al10CeMn2 phase. DSC analysis showed differences in the samples' liquidus temperatures which is indicative of compositional variations. Inductively coupled plasma atomic emission spectroscopy (ICP-OES) and Scheil solidification simulations correlated the compositional differences to phase formation, which agreed with the SEM and DSC results. This experimentation provides insight into novel Al-Ce-Ni-Mn alloys and where their potential lies in industrial applications.

Non steady applied magnetic field impact on a liquid metals has good prospects for industry. For a better understanding of heat and mass transfer processes under these circumstances, numerical simulations are needed. A combination of finite elements and volumes methods was used to calculate the flow and solidification of liquid metal under electromagnetic influence. Validation of numerical results was carried out by means of measuring with ultrasound Doppler velocimetry technique, as well as with neutron radiography snapshots of the position and shape of the solid/liquid interface. As a result of the first part of the work, a numerical model of electromagnetic stirring and solidification was developed and validated. This model could be an effective tool for analyzing the electromagnetic stirring during the solidification process. In the second part, the dependences of the velocity pulsation amplitude and the melt velocity maximum value on the magnetic field pulsation frequency are obtained. It was found numerically the ability of the pulsating force action to develop higher values of the liquid metal velocity at a frequency close to the MHD resonance. Obtained characteristics give a more detailed description of the electrically conductive liquid behaviour under action of pulsating traveling magnetic field.

Lignin is insoluble in water, limiting its use in the synthesis of adhesives. Therefore, in order to increase the amount of lignin raw materials used in the synthesis of adhesives, a kind of aminated lignin compounds was prepared through lignin amination reaction, and conducting structural analysis in this paper. The particle size of the amino lignin is about 100 nm, with the weight average molecular weight of 57,627 g/mol and a water solubility of 0.45g/100ml. The reaction mechanisms were proposed that the phenolic hydroxyl groups of lignin react with ammonia molecules, and thereby successfully introducing amino groups to generate the aminated lignin compounds. Therefore, this article enriches the scientific theory of lignin reactions and provides reference for the widespread application of lignin raw materials in the field of adhesives.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

The theory of heterogeneous nucleation was initially developed as a part of condensed matter physics and later it was used as an important engineering tool to design metallurgical processes. The success leads to wide applications of the theory in metallurgical practice. For example, engineering heterogeneous nucleation in ductile iron has been used to reduce shrinkage defects, suppress cementite formation, and modify size and shape of micro-structural constituencies. This demonstrates how theoretical knowledge could benefit industry practice. This overview aims to summarize the authors’ published studies in co-authorship with colleagues and students, which covered different aspects of engineering heterogeneous nucleation in multiphase cast alloys. Several approaches for engineering heterogeneous nucleation using thermodynamic simulation and practical methods for improving efficiency of nucleation using co-precipitation technique and a local transient melt supersaturation were suggested. Automated Scanning Electron Microscopy Energy-Dispersive-X-ray (SEM/EDX) analysis and a high-resolution Transmission Electron Microscopy (TEM) were used to verify simulation predictions. Practical examples of controlling micro-porosity shrinkage in cast irons with spheroidal graphite are presented to illustrate the power of engineering heterogenous nucleation. The authors appreciate the great efforts that the co-authors have made on the original, overviewed articles here.

The production of high-quality castings without foundry defects at minimal production costs is a constant priority for foundries. Innovation and optimization of production processes are key to achieving this goal. Computer simulation of foundry processes offers a modern alternative to expensive and time-consuming experiments in real foundries and provides a reliable representation and analysis of casting and solidification processes. A detailed analysis of the casting and solidification simulation results allows the prediction of various risks that can cause defects in cast castings, thereby reducing their quality and, last but not least, the cost of their production. The paper deals with the analysis of a computer simulation of the casting of a brake disc in the Slovak foundry. This brake disc has had shrinkages and micro shrinkages that reduce the internal quality of the casting. These defects occurred in the ribs in the upper part of the casting under the feeders. A computer simulation of the casting and solidification of this casting was made according to real conditions. It turned out that the designed ingate system with a system of feeders was not sufficient to eliminate emerging defects. A new layout of the feeders was proposed, which ultimately eliminated the occurrence of defects based on the results of computer simulation. The input parameters were set to be as close as possible to the actual needs of the foundry. 3D models of the assemblies were designed in SolidWorks CAD software, and filling and solidification simulations were performed using the NovaFlow & Solid CV 4.6r42 simulation program.

Knowledge is not merely the characteristic of certain pieces of information being deemed true and justifiable, but rather a process. Within an axiomatic system, the set of information that reaches the status of knowledge forms a universe that provides an interpretation of the reality one aims to describe. Language exchanges information through communication and the process of justification (exchange of information), if it consistently justifies a particular piece of information, it elevates it to knowledge. In this paper, we provide a framework for knowledge within an axiomatic model where we define the fundamental elements of communication and grammar. As a result, the structure dictates that knowledge, to be considered as such, must be investigateable by anyone who utilizes it in its entirety, both in form and content. Ultimately, the development of knowledge processing, referred to as \emph{knowmatics}, represents a clear evolution of the computer science that processes information (subset of knowledge).

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

This work explored and contrasted the effect of microstructure on the tensile properties of AlSi10Mg alloys generated by transient directional solidification depending on variations in cooling rate and Magnesium (Mg) content (i.e., 0.45 and 1wt.% Mg), with a focus on understanding the dendritic growth and phases constitution. Optical and Scanning electron (SEM) microscopies, CALPHAD and thermal analysis were used to describe the microstructure, forming phases and resulting tensile properties. The findings showed that the experimental evolution of the primary dendritic spacing is very similar when both directionally solidified (DS) Al-10wt.% Si-0.45wt.% Mg and Al-10wt.% Si-1wt.% Mg alloys samples are compared. The secondary dendritic spacing was lower for the alloy with more Mg, especially considering the range of high growth velocities. Moreover, a greater fraction of (Al+Si+Mg2Si) ternary eutectic islands surrounding the -Al dendritic matrix was noted for the alloy with 1wt.% Mg. As a result of primary dendritic spacings greater than 180 m related to lower cooling rates, slightly higher tensile properties were attained for the Al-10wt.% Si-0.45wt.% Mg alloy. In contrast, combining dendritic refining (< 150 m) and larger Mg2Si fraction, fast solidified DS Al-10wt.% Si-1wt.% Mg samples exhibited higher tensile strength and elongation. The control of cooling rate and fineness of the dendritic array provided a new insight related to the addition of Mg in slightly higher levels than conventional ones, capable of achieving a better balance of tensile properties in AlSi10Mg alloys.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

The microstructure and solidification behavior of nickel based GTD222 superalloy at different cooling rates are studied. The solidification of the GTD222 superalloy proceeds as follows: L→L+γ, L→L+γ+MC, L→L+(γ/γ ′)-Eutectic and L→η phase. The temperature of liquidus of GTD222 superalloy is 1360 °C while the solidus is slightly lower at 1310 °C, which due to the alloying elements redistribution. It was found that the dendrite arm spacing of the alloy decreased with the increase of cooling rate (From 200 μm at 2.5 K/min to 100 μm at 20 K/min).

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P&lt;0.05), left hippocampus volume (LHV, β: -0.02435, P&lt;0.01) and right hippocampus volume (RHV, β: -0.02544, P&lt;0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P&lt;0.05) and LHV (β: -0.01173, P&lt;0.05) and RHV (β: -0.01193, P&lt;0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P&lt;0.05; RHV, β: -0.005527, P&lt;0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

Capital structure decision plays an imperative role in firm’s performance. Recognizing the importance, there has been many studies inspected the rapport of capital structure with performance of firms and findings of those studies are inconclusive. In addition, there is relative deficiency of empirical studies examining the link of capital structure with performance of banks in Bangladesh. This paper attempted to fill this gap. Using panel data of 22 banks for the period of 2005-2014, this study empirically examined the impacts of capital structure on the performance of Bangladeshi banks assessed by return on equity, return on assets and earnings per share. Results from pooled ordinary least square analysis show that there are inverse impacts of capital structure on bank’s performance. Empirical findings of this study is of greater significance for the developing countries like Bangladesh because it will call upon concentration of the bank management and policy makers to pursue such policies to reduce reliance on debt and to accomplish optimal level capital structure. This research also contributes to empirical literatures by reconfirming (or otherwise) findings of previous studies.

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

Under pure diffusive growth conditions, layered peritectic solidification is possible. In reality, the competitive growth of the primary alfa-phase and the peritectic beta-phase revealed some complex peritectic solidification morphologies due to thermo-solutal convection. The binary organic components TRIS-NPG were used as model system for metal-like solidification. The transparency of the high-temperature non-faceted phases allows studying the dynamic of the solid/liquid interface which lead to peritectic solidification morphologies. Investigations were carried out by using the Bridgman technic for process conditions where one or both phases solidify in a non-planar manner. Different growth conditions were observed which led to competitive peritectic growth morphologies. Additionally, the competitive growth was solved numerically to interpret the observed transparent solidification patterns.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

The extracellular matrix (ECM) plays a key role as both structural scaffold and regulator of cell signal transduction in tissues. In times of ECM assembly and turnover, cells upregulate assembly of the ECM protein, fibronectin (FN). FN is assembled by cells into viscoelastic fibrils that can bind upward of 40 distinct growth factors and cytokines. These fibrils play a key role in assembling a provisional ECM during embryonic development and wound healing. Fibril assembly is also often upregulated during disease states, including cancer and fibrotic diseases. FN fibrils have unique mechanical properties, which allow them to alter mechanotransduction signals sensed and relayed by cells. Binding of soluble growth factors to FN fibrils alters signal transduction from these proteins, while binding of other ECM proteins, including collagens, elastins, and proteoglycans, to FN fibrils facilitates the maturation and tissue specificity of the ECM. In this review, we will discuss the assembly of FN fibrils from individual FN molecules; the composition, structure, and mechanics of FN fibrils; the interaction of FN fibrils with other ECM proteins and growth factors; the role of FN in transmitting mechanobiology signaling events; and approaches for studying the mechanics of FN fibrils.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p &lt; 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Railway transportation is one of the main modes of long-distance coal transportation, and it is inevitable to cause environmental pollution during the transportation process. In order to improve the environment along the railway and increase the utilization rate of coal resources, this paper proposes a detection algorithm for scattered coal solidification layer during transportation based on the YOLO v8 model, and designs an intelligent recognition model suitable for coal solidification layer detection devices by combining fluorescence detection methods. Through experimental analysis, the model meets the requirements of practical detection and plays a crucial role in environmental protection, with strong practical application value.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Understanding the infiltration and solidification processes of liquid 5083Al alloy into Al2O3 three-dimensional reticulated porous ceramic (Al2O3(3D) RPC) is essential for optimizing the microstructure and properties of Al2O3(3D)/5083Al interpenetrating phase composites (IPCs) prepared by low-pressure infiltration process (LPIP). This study employs ProCAST software to simulate the infiltration and solidification processes of liquid 5083Al with pouring velocities (PV) of 0.4 m/s infiltrating into Al2O3(3D) RPC preforms with varying porosities at different pouring temperatures (PT) to prepare Al2O3(3D)/5083Al IPCs using LPIP. The results demonstrate that pore diameter of Al2O3(3D) RPC preforms and PT of liquid 5083Al significantly influence the of the infiltration. Solidification process analysis reveals that the Al2O3(3D) RPC preform with smaller pore diameters allows the lower pouring velocity of 5083Al to solidify faster compared to the preform with larger pore diameters. Al2O3(3D)/5083Al IPCs were prepared successfully from Al2O3(3D) RPC porosity of 15 PPI with liquid 5083Al at PV 0.4 m/s and PT 800 °C using LPIP, resulting in nearly fully dense composites, where both Al2O3(3D) RPCs and 5083Al interpenetrate throughout the microstructure. The infiltration and solidification defects were reduced under air pressure of 0.3 MPa (corresponding to PV of 0.4 m/s) during LPIP. Finite volume method simulations are in good agreement with experimental data, validating the suitability of the simplified model for Al2O3(3D) RPCs in the infiltration simulation.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Acidic ostreolysin A/pleurotolysin B (OlyA/PlyB, formerly known as ostreolysin (Oly), and basic 20 kDa equinatoxins (EqTs) are cytolytic proteins isolated from the edible mushroom Pleurotus ostreatus and the sea anemone Actinia equina, respectively. Both toxins, although from different sources, share many similar biological activities: (i) colloid-osmotic shock by forming pores in cellular and artificial membranes enriched in cholesterol and sphingomyelin; (ii) increased vascular endothelial wall permeability in vivo and perivascular oedema; (iii) dose-dependent contraction of coronary vessels; (iv) haemolysis with pronounced hyperkalaemia in vivo; (v) bradycardia, myocardial ischemia and ventricular extrasystoles accompanied by progressive fall of arterial blood pressure and respiratory arrest in rodents. Both types of toxins are haemolytic within nanomolar range concentrations, and it seems that hyperkalaemia plays an important role in toxin cardiotoxicity. However, it was observed that the haemolytically more active EqT III is less toxic than EqT I, the most toxic and least haemolytic EqT. In mice, EqT II is more than 30 times more toxic than OlyA/PlyB when applied intravenously. These observations imply that haemolysis with hyperkalaemia is not the sole cause of the lethal activity of both toxins. Additional mechanisms responsible for lethal action of the two toxins are direct effects on heart, coronary vasoconstriction and related myocardial hypoxia. In this review, we appraise the pathophysiological mechanisms related to the chemical structure of OlyA/PlyB and EqTs, as well as their toxicity.

Depressions containing partially molten rocks were investigated in Quaternary pebbly sedi-ments in Alpine foreland in Bavaria, Germany. Ruins of limekilns from 18-19th centuries are abundant around Seeshaupt. They are usually associated with earthworks for fuel feeding and protection from wind. Depressions contain partially molten stones from furnace walls, with lime and burnt loam remnants. On the surface of pebbles (typically gneisses), green glass formed with chemical composition possibly affected by moderately volatile components of wood biomass, mainly K and Cu. Thermoplastic deformation of pebbles is limited and the sur-face melt deformation points to slow flow. At Emmerting, on the other hand, two walled circu-lar depressions which lack additional earthworks have been identified as possible impact cra-ters. Thermally affected pebbles show much more intense deformation. Colorless to greenish glass, also K and Cu enriched, usually forms only thin surface coatings, in places covered by younger melt extruded from pebble interior. Burnt loam is missing. At Grabenstätt-Kaltenbach, a depression of unclear origin was investigated. Morphologically, it matches craters rather than limekilns, but anthropogenic contamination (brick-like material) is probable. The rare molten samples do not display extreme deformation features. The thermally affected stones, mainly those from Emmerting, have elevated magnetic susceptibility.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Metallic glass matrix composites are unique new materials which have superior mechanical properties as compared to existing conventional materials. Owing to this, they are potential candidates for various future structural applications. However, they suffer from disadvantages of brittleness, poor ductility and little or no toughness and they manifest catastrophic failure on application of force. Their behavior is dubious and require extensive experimentation to draw conclusive results. In present study, which is continuation of previous study by author, an effort has been made to overcome this pitfall by simulation. A quantitative mathematical model based on KGT theory has been developed to describe nucleation and growth of crystalline phase dendrites in glassy matrix during solidification. It yields information about numerical parameters to understand the behavior of each individual element in a phase in multicomponent sluggish slurry and their effect on final microstructural evolution. Model is programmed and simulated in MATLAB®. Its validation is done by comparison with identical curves reported in literature previously for similar alloys. Results indicate that effect of incorporating all heat transfer coefficients at macroscopic level and diffusion coefficients at microscopic level play a vital role in refining the model and bringing it closer to actual experimental observations. Two types of hypoeutectic and eutectic systems namely Zr₆₅Cu₁₅Al₁₀Ni₁₀ and Zr_47.5Cu_45.5Al₅Co₂ respectively were studied. Simulation results were found to be in good agreement with prior simulated and experimental values

Solidification microstructure is formed under high cooling rates and temperature gradients in powder-based additive manufacturing. In this study, a non-equilibrium multi-phase field method (MPFM), which was based on a finite interface dissipation model proposed by Steinbach et. al., coupled with a CALPHAD database was developed for a multicomponent Ni alloy. A qua-si-equilibrium MPFM was also developed for comparison. Two-dimensional equiaxed micro-structural evolution for the Ni (Bal.)–Al–Co–Cr–Mo–Ta–Ti–W–C alloy was performed at various cooling rates. The temperature–γ fraction profiles obtained under 10^5 K/s using non- and qua-si-equilibrium MPFMs were in good agreement with each other. Over 10^6 K/s, the differences between non- and quasi-equilibrium methods grew as the cooling rate increased. The non-equilibrium solidification was strengthened over a cooling rate of 10^6 K/s. Colum-nar-solidification microstructural evolution was performed under cooling rates from 5×10^5 K/s to 1×10^7 K/s at various temperature gradient values under the constant interface velocity (0.1 m/s). The results showed that as the cooling rate increased, the cell space decreased in both methods, and the non-equilibrium MPFM agreed well with experimental measurements. Our results show that the non-equilibrium MPFM can simulate solidification microstructure in powder bed fusion additive manufacturing.

The role played by non extensive thermodynamics in physical systems has been under intense debate for the last decades. With many applications in several areas, the Tsallis statistics has been discussed in details in many works and triggered an interesting discussion on the most deep meaning of entropy and its role in complex systems. Some possible mechanisms that could give rise to non extensive statistics have been formulated along the last several years, in particular a fractal structure in thermodynamics functions was recently proposed as a possible origin for non extensive statistics in physical systems. In the present work we investigate the properties of such fractal thermodynamical system and propose a diagrammatic method for calculations of relevant quantities related to such system. It is shown that a system with the fractal structure described here presents temperature fluctuation following an Euler Gamma Function, in accordance with previous works that evidenced the connections between those fluctuations and Tsallis statistics. Finally, the fractal scale invariance is discussed in terms of the Callan-Symanzik Equation.

Savannas and adjacent vegetation types like gallery forests are highly valuable ecosystems contributing to several ecosystem services including carbon budgeting. Financial mechanisms such as REDD+ have provided an opportunity for developing countries to alleviate poverty through conservation of its forestry resources. For availing this opportunity carbon stock assessments are essential. Therefore, a research study at two protected areas i.e. Nazinga Game Ranch and Bontioli Nature Reserve, in Burkina Faso was conducted with the objective of assessing carbon Mg C ha-1 in aboveground biomass (AGB)dry of trees in different formations of the south-sudanian savanna in Burkina Faso, West Africa. Similarly analysis of various vegetation parameters was also conducted to understand the overall vegetation structure of these two protected areas. For estimating AGBdry, existing allometric equation for dry tropical woody vegetation types was used. The Importance Value Index (IVI) and Family Importance Value (FIV) were estimated through standard procedures. Various linear and non-linear regression analyses were conducted to test the relationships between carbon and other parameters such as DBH, height and basal area (BA). The results showed that both sites collectively contain mean carbon of 3.41 ± 4.98 Mg C ha-1. Amongst different vegetation types, gallery forests recorded the highest mean carbon of 9.38 ± 6.90 Mg C ha-1. The highest IVI of 115.56 at Nazinga Game Ranch was recorded for Anogeissus leiocarpa. Similarly, highest IVI of 98.59 was recorded for Mitragyna inermis at Bontioli Nature Reserve. The highest FIV was recorded for Combretaceae for both of the sites. To our knowledge, this was the first study conducted to assess the carbon stocks at the two protected areas in southern Burkina Faso. The study therefore was an attempt for addressing the knowledge gap particularly on carbon stocks of protected savannas. It could serve as a baseline for carbon stocks for future initiatives such as payment for environmental services and REDD+ at these areas.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

Many studies discuss carbon-based materials because of the versatility of its element. They include different opinions for scientific problems and discuss fairly at convincing and compelling levels within the scope and application. A gas-state carbon atom converts into various states depending on its conditions of processing. The electron transfer mechanism in the gas-state carbon atom is responsible to convert it into various states, namely, graphite, nanotube, fullerene, diamond, lonsdaleite and graphene. The shape of ‘energy trajectory’ enables transferring electrons from the left- and right-sides of an atom is like a parabola. That ‘energy trajectory’ is linked to states (filled state and suitable nearby unfilled state) where force-exertion along the poles of transferring electrons is remained balance. So, the mechanism of originating different states of a gas-state carbon atom is under the involvement of energy first. This is not the case for atoms executing confined inter-state electron-dynamics as the force is involved first. Graphite-, nanotube- and fullerene-state atoms ‘partially evolve partially develop’ (form) their structures. These possess one-dimensional, two-dimensional and four-dimensional ordering of atoms, respectively. Their structural formation also comprises ‘energy curve’ having a shape-like parabola. Transferring suitable filled state electron to suitable nearby unfilled state is under a balance force exerting along the poles. The graphite structure under only attained-dynamics of atoms can also be formed but in two-dimension. Here, binding energy between graphite-state carbon atoms is for a small difference of exerting forces along their opposite poles. Structural formation in diamond, lonsdaleite and graphene atoms involve energy to gain required infinitesimal displacements of electrons through which they maintain orientationally-controlled exerting forces along dedicated poles. In this study, the growth of diamond is found to be south to east-west (ground) where atoms bound ground to south. Thus, diamond atoms merge for a tetra-electron ground to south topological structure. Lonsdaleite atoms merge for a bi-electron ground to just-south topological structure. The growth of graphene is found to be north to ground where atoms bound ground to north. Thus, graphene atoms merge for a tetra-electron ground to north topological structure. Glassy carbon exhibits layered-topological structure where, tri-layers of gas-, graphite- and lonsdaleite-state atoms successively bind in repetitive order. Nanoscale hardness is also sketched based on different force-energy behaviors of different state carbon atoms. Here, structure evolution in each carbon state atom explores its own science.

Planck's constant plays an important role in quantum mechanics but has little physical meaning apart from its contribution to the formulas. Evaluating each of the constant's unit dimensions gives a more granular account of the physical phenomena described by the equations. These formulas show how classical and quantum mechanical equations are related, and they give consistent descriptions of phenomena like momentum and energy in classical and quantum systems.

G-quadruplexes are noncanonical nucleic acid structures formed from stacked guanine tetrads. They are frequently used as building blocks and functional elements in fields such as synthetic biology and also thought to play widespread biological roles. G-quadruplexes are often studied as monomers but can also form a variety of higher-order structures. This increases the structural and functional diversity of G-quadruplexes, and recent evidence suggests that it could also be biologically important. In this review we describe the types of multimeric topologies adopted by G-quadruplexes and highlight what is known about their sequence requirements. We also summarize the limited information available about potential biological roles of multimeric G-quadruplexes and suggest new approaches that could facilitate future studies of these structures.

This paper studies a model of dynamic compensation and capital structure with managerial traits. We show that Optimistic manager perceives equity as more undervalued than debt, while, confident manager perceives debt as more undervalued than equity. Managerial risk aversion mitigates manager’s bias. The risk aversion of the optimistic manager has a convex effect on the optimal coupon. There exists the level of risk aversion eliminating the bias on the leverage. The managerial optimist has an ambiguous effect on the owner’s bankruptcy level. The risk aversion has a convex effect on the owner’s bankruptcy level. The optimistic/confident manager underestimates the credit spread. The risk aversion has convex effect on the credit spread. In contrast to rational manager, the optimistic/confident manger has higher level of effort. The risk aversion has a negative effect on the effort.

Tyrosine kinase fibroblast growth factor receptor (FGFR), which is aberrant in various cancer types, is a promising target for cancer therapy. Here we reported the design, synthesis, and biological evaluation of a new series of 6-(2,6-dichloro-3,5-dimethoxyphenyl)-4-substituted-1H-indazoles derivatives as potent FGFR inhibitors. Compound 10a was first identified as a potent FGFR1 inhibitor, with good enzymatic inhibition. Further structure-based optimization revealed that compound 13a is the most potent FGFR1 inhibitor in this series with the enzyme inhibitory activity about 30.2 nM of IC50 value.

It is commonly recognized that a ship’s ability to maintain stability is dependent upon the way its loads are distributed. This means making sure the center of gravity is sufficiently low and evenly distributed. Yet when a ship encounters turbulent water with extremely large wave amplitudes, load distribution is a critical factor in determining how stressed the ship becomes. In particular, this article examines several methods for increasing the ship's longitudinal strength to prevent ship structural damage during hogging and sagging. This research presents a number of proposed techniques to enhance the longitudinal strength of cargo ships in order to guarantee minimal stress and deformation during sagging and hogging. The first method is the stern-to-bow use of curved support structures to increase the longitudinal strength of a cargo ship. And another way to stiffen the lateral plate is the proposed use of different designs of the side plate, such as wavy curves, stars, etc. To further boost the strength, the lateral plate upper part is suggested to curve upward. A numerical simulation using ANSYS of the stiffened plate when subjected to uniform load distribution and fixed support on either end shows that there is a decrease in deformation of the plate when we use wavy curved plates compared with those of the other plate stiffening methods used, and furthermore, curving the plate on top increases its strength during sagging as well as hogging. Finally, the use of a curved support structure further enhanced the overall longitudinal strength of the vessel.

A review is given of the experimental values of the magnetic hyperfine structure and the Bohr-Weisskopf effect in muonic atoms. The need for more measurements and systematic calculations is discussed in the light of distinguishing between different models of the Bohr-Weisskopf effect in nuclei.

ZnO has many technological applications which largely depend on its properties that can be tuned by controlled synthesis. Ideally, the most convenient ZnO synthesis is carried out at room temperature in aqueous solvent. However, the correct temperature values are often loosely defined. In the current paper we performed synthesis of ZnO in aqueous solvent, by varying reaction and drying temperature by 10°C steps and monitored the synthesis products primarily by XRD. We found out that a simple direct synthesis of ZnO, without additional surfactant, pumping of freezing, required both a reaction (TP) and a drying (TD) temperature of 40°C. Higher temperatures also afford ZnO, but lowering any of the TP or TD below the threshold value results either in the achievement of Zn(OH)2 or in a mixture of Zn(OH)2/ZnO. A more detailed Rietveld analysis of the ZnO samples reveals a density variation with the synthesis temperature and an increase of the nanoparticles average size also verified by SEM images. The optical properties of ZnO obtained by UV-Vis reflectance spectroscopy indicate a red shift of the band gap by ~0.1 eV.

Design and advancement of the durable urban train infrastructures are of utmost importance for reliable mobility in the smart cities of the future. Given the importance of urban train lines, tunnels, and subway stations, these structures should be meticulously analyzed. In this research, two-dimensional modeling and analysis of the soil-structure mass of the Alan Dasht station of Mashhad Urban Train are studied. The two-dimensional modeling was conducted using Hashash’s method and displacement interaction. After calculating the free-field resonance and side distortion of the soil mass, this resonance was entered into PLAXIS finite element program, and finally, stress and displacement contours together with the bending moment, shear force and axial force curves of the structure were obtained.

1) Background: Traditionally, complex biological products such as vaccines presented unique challenges to implementation of even rudimentary characterization packages; thus, the product was defined almost exclusively by its manufacturing process. The advances in technology and analytical tools allowed the application of more comprehensive characterization packages for products such as adsorbed combination vaccines, which contain several antigens in a single formulation to protect against more than one disease, and may contain adjuvants and excipients. Aluminum phosphate (AlPO4) is a well-established adjuvant for enhancing the uptake of vaccines and to induce robust immunity against pathogens. During manufacturing, adjuvant is mixed with protein antigens which may in turn impact their higher order structure and stability. 2) Methods: To study the structural changes of protein antigens after adsorption several analytical tools including DLS, FTIR, Fluorescence, LD, and SEM were used. 3) Results: the AlPO4 adjuvant suspension consists of small submicron particles that form a continuous porous surface. Secondary structure alpha-helix and beta-sheet content of DT and TT increased after adsorption to AlPO4 adjuvant, whereas no significant changes were noted for other protein antigens. Interactions were noted between AlPO4 adjuvant and DT, TT, and FHA. 4) Conclusions: here we report for the first time the use of SEM for the visualization of adsorbed multivalent vaccine components. A unique signature profile detected for each multivalent vaccine by FTIR can be used as a lean in-process test to verify vaccine product composition and identity prior to filling.

A fully relativistic description of an atomic clock is achieved by applying the equivalence principle directly to the space-time coordinates of electron transitions. The resulting differential equation of motion is then reformulated by means of Hamilton's principle to obtain an equivalent integral equation. Generalized coordinates describe the electron in a configuration space consisting of three coordinates that define the origin, or nucleus, and three coordinates that define the manifold on which the electron is constrained to move (the electron shells). Following Dirac the particle model is transformed to a field model by describing energy quantization as the four-dimensional localization of radial and transverse electromagnetic fields. It can then be compared to the emission energy of galaxies in terms of the radial baryonic fields and transverse gravitomagnetic fields that emanate from black holes. The symmetry exhibited by these diverse forms of energy demonstrates that the properties of energy, when described four-dimensionally with time, are independent of the material system which supports them.

Recent advancements in artificial intelligence (AI) and deep learning have revolutionized the field of protein engineering, particularly in the area of de novo protein design. This review article explores the impact of AI-driven approaches on protein design, with a specific focus on the role of structure prediction neural networks, such as AlphaFold and RoseTTAFold. The article discusses the paradigm shift brought about by these networks, which have enabled the design of proteins with unique structures and functions that are not found in nature. The review covers various aspects of AI-driven protein design, including the use of protein language models to harness evolutionary information, the development of de novo protein design workflows utilizing deep learning, and the application of generative models like RFdiffusion and RoseTTAFold All-Atom. The article also highlights the successes and applications of AI-driven protein design across diverse domains, such as enzyme engineering, antibody design, and vaccine development. Additionally, the review identifies current challenges and future directions in the field, emphasizing the need to address limitations in modeling conformational dynamics and designing proteins for in vivo functionality. The article concludes by underscoring the potential of AI-driven protein design to transform various aspects of science and technology, while also acknowledging the importance of interdisciplinary collaboration and the development of robust pipelines for the validation and optimization of designed proteins. Overall, this comprehensive review serves as a valuable resource for researchers and practitioners interested in understanding the current state and future prospects of AI-driven protein design.

This paper introduces an innovative approach to numerically model Structure-Soil-Structure Interaction (SSSI) by integrating the Boundary Element Method (BEM) and the Finite Element Method (FEM) in a coupled manner. To assess the accuracy of the proposed method, a comparative study is undertaken, comparing its outcomes with those generated by the conventional FEM technique. Alongside accuracy, the computational efficiency aspect is crucial for the analysis of large-scale SSSI problems. Hence, the computational performance of the coupled BEM-FEM method undergoes a thorough examination and is compared with that of the standalone FEM method. The results from these comparisons illustrate the superior capabilities of the proposed method in comparison to the FEM method. The novel approach provides more reliable results compared to traditional FEM methods, serving as a valuable tool for engineers and researchers involved in structural analysis and design.

Abstract—In this paper, decidability of the structures of real, rational, integer and natural numbers will be studied in different languages. Decidability or undecidability of mathematical structures is one of the fundamental and sometimes very difficult problems of mathematical logic, where several examples of problems in this field are still open and unresolved even after decades. One of the goals of Mathematical Logic is the axiomatization of mathematical theoriesTarski has proved the decidability of the theory of real and complex numbers in the language of addition and multiplication, and it is proved that theories of natural, integer, and rational numbers, in the language of addition and multiplication, are undecidable (Theorems of Gödel and Robinson). We will review The following problemes: The Main Problem 1: ⟨Q; ⊑⟩ is decidable? Problem 2: an explicit axiomatization for ⟨Z; \times⟩? and we will study boolean algebras. Boolean algebras are famous mathematical structures.Tarski showed the decidability of the elementary theory of Boolean algebras.In this paper, we study the different kinds of Boolean algebras and their properties. And we present for the first-order theory of atomic Boolean algebras a quantifier elimination algorithm. The subset relation is a partial order and indeed a lattice order,And I will prove that the theory of atomic Boolean lattice orders is decidable, and furthermore admits elimination of quantifiers. So the theory of the subset relation is decidable. And we will study decidability of atomlss boolean algebra.

We discuss three key points: defining mathematically the notions of phase, symmetry breaking, topological defects and their stability in a formal language of homotopy theory and fiber bundle formalism; postulating and proving two theorems for successive symmetry breaking scenarios in condensed matter physics and cosmology, and demonstrating application of theorems to superfluid Helium 3 and Kibble-Lazarides-Shafi (KLS) walls, supporting and mathematically justifying the results of [Volovik, 2020].

The solid-state technique was utilized to make a single phase of delafossite CuAlO2, along with 1%, 2%, 3% and 4% silver doped CuAlO2 samples in this study. The content of the samples was investigated using energy dispersive X-ray spectroscopy (EDS) equipped with a field emission scanning electron microscope (FE-SEM). The polycrystalline nature of all of the analyzed cases was confirmed by structural analyses utilizing an X-ray diffraction (XRD) pattern with a simple typical peak of CAO rhombohedral phase. Raman, FT-IR and UV–Vis spectroscopy were used to study the structural, and optical energy band gap (Eg) of Ag doped CuAlO2 nanoparticles. The Kubelka–Munk function was used to calculate the optical band gap of ACAO alloys using diffuse reflectance spectra, and it altered as the Ag ion concentration increased. A. c. impedance spectroscopy was used to investigate the dielectric characteristics of Ag doped CuAlO2 nanoparticles.

SETMAR is a protein lysine methyltransferase that is involved in several DNA processes, including DNA repair via the non-homologous end joining (NHEJ) pathway, regulation of gene expression, illegitimate DNA integration, and DNA decatenation. However, SETMAR is an atypical protein lysine methyltransferase since in anthropoid primates, the SET domain is fused to an inactive DNA transposase. The presence of the DNA transposase domain confers to SETMAR a DNA binding activity towards the remnants of its transposable element, which has resulted in the emergence of a gene regulatory function. Both the SET and the DNA transposase domains are involved in the different cellular roles of SETMAR, indicating the presence of novel and specific functions in anthropoid primates. In addition, SETMAR is dysregulated in different types of cancer, indicating a potential pathological role. While some light has been shed on SETMAR functions, more research and new tools are needed to better understand the cellular activities of SETMAR and to investigate the therapeutic potential of SETMAR.

Biomolecular structure drives function, and computational capabilities have progressed such that the prediction and computational design of biomolecular structures is increasingly feasible. Because computational biophysics attracts students from many different backgrounds and with different levels of resources, teaching the subject can be challenging. One strategy to teach diverse learners is with interactive multimedia material that promotes self-paced, active learning. We have created a hands-on education strategy with a set of fifteen modules that teach topics in biomolecular structure and design, from fundamentals of conformational sampling and energy evaluation to applications like protein docking, antibody design, and RNA structure prediction. Our modules are based on PyRosetta, a Python library that encapsulates all computational modules and methods in the Rosetta software package. The workshop-style modules are implemented as Jupyter Notebooks that can be executed in the Google Colaboratory, allowing learners access with just a web browser. The digital format of Jupyter Notebooks allows us to embed images, molecular visualization movies, and interactive coding exercises. This multimodal approach may better reach students from different disciplines and experience levels as well as attract more researchers from smaller labs and cognate backgrounds to leverage PyRosetta in their science and engineering research. All materials are freely available at https://github.com/RosettaCommons/PyRosetta.notebooks.

In the work, the nuclei structure was modeled by a system of shells consisting of combinations of spherical and annular vortices. Having connected the spin and the magnetic moments of the nuclei with the dynamics of the outer shell of the nucleus, we determined its type and carried out a semiempirical calculation of the parameters of its structure for stable and unstable nuclear isotopes in the sequence of the order number Z from 1 to 37. Comparison of the obtained nuclear sizes with the radii of the electron shells of atoms made it possible to reveal a definite correlation. On the basis of it, it was concluded that the periodic law of Mendeleyev can determine the patterns in the change in the structure of the atomic nucleus.

This paper utilizes dynamic panel threshold technology to conduct a nonlinear test on the direct effect between environmental regulation and economic fluctuations and the effect of industrial structure upgrading by taking 35 industrial sectors in China from 2003 to 2016 . The research has found that there is an inverted "U" relationship between environmental regulation and economic fluctuations, with the enhancement of environmental regulations, the economic fluctuation increases first and then decreases. The cross-terms of environmental regulation and industrial structure rationalization or industrial structure upgrading are significantly negative, which indicates that the enhancement of environmental regulation is conducive to promoting industrial structure upgrading and reducing the economic fluctuations. While the rationalization factors of industrial structure and advanced industrial structure are significantly negative, indicating that both forms of industrial structure upgrading are conducive to reducing the economic fluctuations. Environmental regulation has technical innovation thresholds for industrial structure upgrading and economic fluctuations, but there are no human capital or FDI thresholds. In the rationalization model of industrial structure, there is a nonlinear "U" relationship between environmental regulation and economic fluctuations when the proportion of scientific research expenditure is more than 1.35%. With the enhancement of environmental regulation, the economic fluctuation reduces first and then increases, and the corresponding inflection point value is 2.398% of the environmental regulation level. At the same time, the environmental regulation can indirectly reduce economic fluctuations by pushing down the industrial structure upgrades. In the advanced model of industrial structure, there is a “U” relationship between environmental regulation and economic fluctuation when the proportion of scientific research expenditure is greater than 1.26%. With continuous enhancement of environmental regulation, the economic fluctuation reduces first and then increases. The corresponding inflection point value is 1.78% of the environmental regulation level, and environmental regulation can indirectly reduce economic fluctuations by promoting the industrial structure at the same time.

Most non-infectious diseases are associated with dysfunction of proteins or protein complexes. Аssociation between sequence and structure is analyzed since a long time, and analysis of sequence organization in domains and motifs is actual research area. A mathematical method is proposed here to identify the hierarchical organization of protein sequences. The method is based on pentapeptide as a unit of protein sequences. This method was applied on a non-homologous dataset of protein sequences. The analysis revealed 11 hierarchical levels of protein sequence organization, showing the relationship of these multiple fragments of sequences. Using different examples, we illustrated how the fragments of the spatial structure of protein correspond to the elements of the hierarchical structure of the protein sequence. A hierarchical structure is observed in the protein sequence. This methodology is an interesting basis for mathematically based classification of elements of spatial organization of proteins. Elements of the hierarchical structure of different levels of the hierarchy can be used for biotechnological and medical problems.

Understanding the flow in urban environments is an increasingly relevant problem due to its significant impact on air quality and thermal effects in cities worldwide. In this review we provide an overview of efforts based on experiments and simulations to gain insight into this complex physical phenomenon. We highlight the relevance of coherent structures in urban flows, which are responsible for the pollutant-dispersion and thermal fields in the city. We also suggest a more widespread use of data-driven methods to characterize flow structures as a way to further understand the dynamics of urban flows, with the aim of tackling the important sustainability challenges associated to them.

The contribution deals with the joining of various types of materials by technology of thermal drilling. In various branches of industries, also in the automotive industry must be joining operations, service, repairing, substitution or protection workpieces, components with various types of materials. Equally, the important role as joint, is also used material, and a product preparation by assembly and disassembly operations. By utilization of new friction hybrid joining technologies we can shortage the production time, provide automation in operations, increase the quality of joints, spare of economical expenses and also we can protect the environment. In this paper authors have investigated the effect of friction drilling on the tested material, aluminium alloy AlMgSi, which was used for material testing. The created joints were evaluated visually and by microscopy methods. The errors of tested joining were documented and described, too. This contribution was made with cooperation of Technical University of Kosice and with U. S. Steel Kosice, s.r.o.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

The Internet's core network, crucial for key services, lacks a clear definition, hindering Internet development and security research. This study analyzes important Autonomous Systems (ASes) and proposes a rule-filtering, top-down method to infer the Internet's core network. It identifies two core memberships: Tier-1 ASes and Regional Tier-1 ASes. Despite a gap, Regional Tier-1 ASes show potential to join the core. Our proposed core structure, unlike traditional methods that randomly select TOP-K nodes, offers improved rationality and interpretability. Historical data analysis reveals the Internet's core structure as a tightly interconnected network of large provider ASes. Despite some changes, this structure shows remarkable stability and growing influence, potentially encouraging other ASes to establish direct connections with the core ASes, accelerating the trend towards a flattened Internet structure. Furthermore, the core structure may be evolving from a majority to a more minority-centric structure.

Complex-structured polymeric microparticles hold significant promise as advance in next-generation medicine mostly due to demand from developing targeted drug delivery. However, the conventional methods for producing these microparticles of defined size, shape and sophisticated composition often face challenges in scalability, reliance on specialized components such as micro-patterned templates, or have limited control over particle size distribution and cargo release kinetics. In this study, we introduce a novel and reliably scalable approach for manufacturing microparticles of defined structures and sizes with variable parameters. The concept behind this method involves the deposition of a specific number of polymer layers on a substrate with low surface energy. Each layer can serve as either the carrier for cargo or a programmable shell-former with predefined permeability. Subsequently, this layered structure is precisely cut into desired-sized blanks using a laser. The manufacturing process is completed by applying of heat to the substrate what results on sealing the edges of the blanks. The combination of the high surface tension of the molten polymer and the low surface energy of the substrate enables the formation of discrete particles, each possessing semi-spherical or other designed geometries determined by their internal composition. Such anisotropic microparticles are envisaged versatile applications.

Single crystals of quaternary adamantine type Cu•GaGeS4 were grown by chemical vapor transport technique using iodine as transport agent. Dark red transparent crystals grew in a temperature gradient of dT = 900–750 °C. Chemical characterization by X-ray fluorescence showed an off-stoichiometric composition of the Cu•GaGeS4 crystals, in particular a slight Ge-deficit. By X-ray diffraction, Cu•GaGeS4 was found to adopt the chalcopyrite-type structure with the space group I-42d. The cation distribution in this structure was analyzed by multiple energy anomalous synchrotron X-ray diffraction and it was found that Cu and vacancies occupy the 4a site, whereas Ga and Ge occupy the 4b site. The band gap energies of several off-stoichiometric Cu•GaGeS4 crystals were determined by UV-Vis spectroscopy and are in the range of 2.1 to 2.4 eV. A non-linear correlation of the band gap energy with the Ge-content of the compound follows the usual bowing behaviour of semiconductor alloys with a bowing parameter of b = 1.45(0.08).

The composition, structure and functionalities of prolamins from highland barley was investigated. These parameters of was compared with the widely applied prolamins (zein). There are more charged and hydrophilic amino acids in prolamins from highland barley than zein. The molecu-lar weight of prolamins from highland barley were between 30 to 63 kDa, which was larger than zein (20 to 24 kDa). β-turn helices is the main secondary structure in prolamins from highland barley, while α-helical structure is the main secondary structure in zein. The water holding capacity, thermal stability, emulsifying capacity and stability of prolamins from highland barley is quite lager than zein, while opposite results can be observed for oil absorption capacity. The diameter of fibers prepared with prolamins from highland barley was almost 6 times that of zein, while ribbon structures rather than fibers were formed by prolamins from highland barley. The results would provide the guidance for application of prolamins from highland barley.

The Lokpaukwu Uru Quarry was examined geologically, geophysically, and core-wise. The location is between 5056.149'N and 5056.193'N and 7028.312'E and 7028.356'E. The study location may include the Asu River Group and the Eze-Aku Formation. This area has five rock units. In the eastern research region, siltstone forms a "CAP" on the shale. Shale underlies half of the study area. The west has calcareous sandstone. The eastern part of the area is dolerite, the main rock that spans siltstone and shale. The region's geological matter contains iron. Two geological sections were analysed and interpreted to identify the five rock units and their outcrops in the study area. electroresistivity in geophysical research Schlumberger found that the western, northwesterly, and central sections of the research region had a thick sedimentary sequence, whereas the eastern half has an igneous body, the project's main component. Sandstone, siltstone, and shale follow the high-resistivity rock in this location. The rock unit in the region was found in eleven core samples from the east half of the study area. Nine rock-unit core samples were found near Obichioke. The Lokpaukwu area's core data shows the rocks' positions, kinds, minerals, and strengths. Geologic mapping shows that a major fault separates the viable Uru end from the unviable Obichioke lot. Recrystallization dominates the fault track (alcitic matter). Thus, prior to quarrying igneous (basic) units, comparable investigations are advised.

In this study, Acısu Basin, which is upper side of one of the most important basins (Gediz) in Türkiye, was modelled using three types of hydrological models and three different calibration algorithms. Lumped (GR4J), semi-distributed (SWAT+), and fully distributed (mHM) hydrological models were built and integrated with Parameter Estimation Tool (PEST) which is a model independent calibration tool including various algorithms. Levenberg Marquardt (L-M), Shuffled Complex Evolution (SCE), and Covariance Matrix Adoption Evolution Strategy (CMA-ES) were selected as calibration algorithms. Calibration period was 1991-2000, and validation results were obtained for 2002-2005. The effect of model structure and calibration algorithm selection on discharge simulation was evaluated via comparison of 9 different model-algorithm combinations. Results have shown that mHM and CMA-ES combination showed the best discharge simulation performance according to NSE values (calibration: 0.67, validation: 0.60). Although statistically the model results were classified as acceptable, the pattern comparison of discharge value shows that all of the models miss the peak values in significant amounts. This problem may be related to the interventions made in 2000-2001 years interval and possible to overcome by changing the calibration and validation periods, increasing the number of iterations or using the naturalized gauge data.

Egg white lysozyme was modified by chemical methods using organic acids. Caffeic acid and p-coumaric acid in organic acids were used as modifiers, and 1-Ethyl-3- (3-dimethylaminopropyl) carbodiimide hydrochloride and N-hydroxy succinimide were used as dehydration condensation agents during modification. A certain degree of modified lysozyme was obtained through appropriate modification conditions. The antibacterial properties and structure of the obtained two organic acid modified lysozymes were compared with natural enzymes. The results showed that compared with the natural enzyme, the activity of modified lysozyme decreased, but the inhibitory effect on Gram-negative bacteria was enhanced. The minimum inhibitory concentrations of caffeic acid modified enzyme and p-coumaric acid modified enzyme on Escherichia coli and Pseudomonas aeruginosa were 0.5 mg/mL and 0.75 mg/mL, respectively. However, the antibacterial ability of modified lysozyme to Gram-positive bacteria was lower than that of natural enzyme. The minimum inhibitory concentration of caffeic acid modified enzyme and p-coumaric acid modified enzyme to Staphylococcus aureus and Bacillus subtilis was 1.25 mg/mL. The peak fitting results of the amide-I band (1600 cm-1-1700 cm-1) absorption peak in the infrared spectroscopy showed that the content of the secondary structure of the two modified enzymes obtained after modification was different from that of natural enzymes.

Surface temperature influences human health directly and alters the biodiversity and productivity of the environment. While previous research has identified that the composition of urban landscapes influences the physical properties of the environment such as surface temperature, a generalizable and flexible framework is needed that can be used to compare cities across time and space. This study employs the Structure of Urban Landscapes (STURLA) classification combined with remote sensing of New York City’s (NYC) surface temperature. These are then linked using machine learning and statistical modeling to identify how greenspace and the built environment influence urban surface temperature. It was observed that areas with urban units composed of largely the built environment hosted the hottest temperatures while those with vegetation and water were coolest. Likewise, this is reinforced by borough-level spatial differences in both urban structure and heat. Comparison of these relationships over the period between2008 and 2017 identified changes in surface temperature that are likely due to the changes in prevalence in water, lowrise buildings, and pavement across the city. This research reinforces how human alteration of the environment changes ecosystem function and offers units of analysis that can be used for research and urban planning.

Although the presence of dark energy is well established from various observations, its true nature is still not well understood. The cosmological constant term seems to be the preferred candidate. In earlier work we had a constant cosmological constant term to limit the sizes of large-scale structures at lower redshifts. In this work, we extend this to large scale structures at higher redshifts. Here we invoke a time varying cosmological constant to set constraints on sizes of galaxies at high redshifts and see that they are consistent with their observed sizes. The time-varying cosmological constant also provides a possible solution to the puzzle of structure formation of large disk galaxies (like the Wolfe disk) observed at very early stages of the Universe. Future observations of galaxies at even higher redshifts could support our approach.

Entamoeba histolytica, like other Organismes, is characterized by diversity and heterogeneity in its genetic content, which is one of the most important reasons for survival, and the increase in susceptibility to infection.Non-condensation of chromosomes during the process of cell division and the ambiguity of the chromosomal ploidy makes predicting the exact chromosomal number difficult. Genes distributed across 14 chromosomes as well as many extra-chromosome elements. Most Genes composed of one axon only, with Introns in 25% of Genes. This genome is characterized by the presence of Polymorphic internal repeat regions, and several gene families, one of these large families encoding Transmembrane kinas, Cysteine protease (CP), SREHP protein, and others.

One method of creating a brass coating is through electrodeposition, which is most often completed in cyanide galvanic baths. Because of the toxicity of cyanides, many are working on the development of cyanide-free baths, which are promising but not satisfactory to replace the classic methods. The purpose of the study was to explore a new generation of non-aqueous cyanide-free baths based on 1-ethyl-3-methylimidazolium acetate ionic liquids. The study involved the formation of copper, zinc, and brass coatings. The influence of the bath composition, cathodic current density, and temperature was determined. The obtained coatings were characterized by their morphology, chemical composition, roughness, and corrosion resistance. It was found that the structure of the obtained coatings is strongly dependent on the process parameters. The three main structures observed were fine-grained, porous, and olive-like. To the best knowledge of the authors, it is the first time the olive-like structure was observed in the case of an electrodeposited coating. The Cu-Zn coatings consisted of 19–96 at.% copper and exhibited relatively strong corrosion resistance. High improvement of corrosion properties was found in the case of copper and brass coatings with an olive-like structure.

This article presents description of social structures such as, for example, states, in the context of their consideration as systems. Moreover, it seeks to develop K. Marx’s model in terms of systematic approach, as well as to justify the application of the Fibonacci sequence to systems in general and, in particular, to social systems. The description covers a wide range of issues, ranging from the assertion of the basic principle of living systems as patterns in resources flows to description of functions of various aspects of states and their economics in terms of objective needs of such structures. In addition, this article justifies synergetic effect based on proposed model, and the way this effect is applied to state systems. Moreover, it includes the description of main changes of socio-economic formations throughout the history as a natural development of social systems, including possible modern stages. The fundamental tool of this description is description of essence of the mechanism of property rights and its formation options. The differences of two extreme directions of such development are also described on the basis of the objective factor of resource provision. Special attention is given to the concept of surplus value as a feature of social production systems.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

The structure of turbulent flow over non-flat surfaces is a topic of major interest in practical applications in both engineering and geophysical settings. A lot of work has been done in the fully rough regime at high Reynolds numbers where the effect on the outer layer turbulence structure and the resulting friction drag is well documented. It turns out that surface topology plays a significant role on the flow drag especially in the transitional roughness regime and therefore, hard to characterize. Survey of literature shows that roughness function depends on the interaction of roughness height, flow Reynolds number and topology shape. In addition, if the surface topology contains large enough scales then it can impact the outer layer dynamics and in turn modulate the total frictional force. Therefore, it is important to understand the mechanisms underlying drag increase from systematically varied surface undulations in order to better interpret quantifications based on mean statistics such as roughness function. In this study, we explore the mechanisms that modulate the turbulence structure over a two-dimensional (2D) sinusoidal wavy surface with a fixed amplitude, but varying slope. To accomplish this, we model the turbulent flow between two infinitely wide 2D wavy plates at a friction Reynolds number, $Re_{\tau}=180$. We pursue two different but related flavors of analysis. The first one adopts a roughness characterization flavor of such wavy surfaces. The second one focuses on understanding the non-equilibrium near surface turbulence structure and their impact on roughness characterization. Analysis of the different statistical quantifications show strong dependence on wave slope for the roughness function indicating drag increase due to enhanced turbulent stresses resulting from increased production of vertical velocity variance from the surface undulations.

Micro elastofluidics is a transformative branch of microfluidics, leveraging fluid-structure interaction (FSI) at the microscale to enhance the functionality and efficiency of various microdevices. This review paper elucidates the critical role of advanced computational FSI methods in the field of micro elastofluidics. By focusing on the interplay between fluid mechanics and structural responses, these computational methods facilitate the intricate design and optimisation of microdevices such as microvalves, micropumps, and micromixers, which rely on the precise control of fluidic and structural dynamics. In addition, these computational tools extend to the development of biomedical devices, enabling precise particle manipulation and enhancing therapeutic outcomes in cardiovascular applications. Furthermore, this paper addresses the current challenges in computational FSI and highlights the necessity for further development of tools to tackle complex, time-dependent models under microfluidic environments and varying conditions. Our review highlights the expanding potential of FSI in micro elastofluidics, offering a roadmap for future research and development in this promising area.

Every subset S of a Cartesian spaces Rd, endowed with differen- tial structure C∞(S) generated by restrictions to S of functions in C∞(Rd), has a canonical partition M(S) by manifolds, which are or- bits of the family X(S) of all derivations of C∞(S) that generate local one-parameter groups of local diffeomorphisms of S. This partition satisfies the frontier condition, Whitney’s conditions A and B. If M(S) is locally finite, then it satisfies all definitions of stratification of S. This result extends to Hausdorff locally Euclidean differential spaces.

Herpesviridae is a family of enveloped double-stranded DNA viruses that cause a wide range of diseases in hosts. Among the various components of herpesvirus particles, tegument proteins residing between the envelop and nucleocapsid play crucial roles in viral replication, immune evasion, and modulation of host cellular pathways. Understanding the three-dimensional structure of herpesvirus tegument proteins help to reveal the molecular mechanism underlying the crosstalk with other viral and cellular components, and thus is crucial for the investigation of their biological and pathological functions. In this review, we summarize the current knowledge of the structural features of herpesvirus tegument proteins, highlighting the structure-based functional implications, including the potential as targets for antiviral drug development.

A modern binary executable is a composition of various networks. Control flow graphs are commonly used to represent an executable program in labeled datasets used for classification tasks. Control flow and term representations are widely adopted, but provide only a partial view of program semantics. This study is an empirical analysis of the networks composing malicious binaries in order to provide a complete representation of the structural properties of a program. This is accomplished by the measurement of structural properties of program networks in a malicious binary executable dataset. We demonstrate the presence of Scale-Free properties of network structure for program data dependency and control flow graphs, and show that data dependency graphs also have Small-World structural properties. We show that program data dependency graphs have a degree correlation that is structurally disassortative, and that control flow graphs have a neutral degree assortativity, indicating the use of random graphs to model the structural properties of program control flow graphs would show increased accuracy. By providing an increase in feature resolution within labeled datasets of executable programs we provide a quantitative basis to interpret the results of classifiers trained on CFG graph features. An increase in feature resolution allows for the structural properties of program classes to be analyzed for patterns as well as their component parts. By capturing a complete picture of program graphs we can enable theoretical solutions for the mapping a program's operational semantics to its structure.

Nuclear lamins are type V intermediate filament proteins that form a filamentous meshwork beneath the inner nuclear membrane. Additionally, a sub-population of A-type and B-type lamins is localized in the nuclear interior. The nuclear lamina protects the nucleus from mechanical stress and mediates nucleo-cytoskeletal coupling. Lamins form a scaffold that partially tethers chromatin at the nuclear envelope. The nuclear lamina also stabilizes protein-protein interactions involved in gene regulation and DNA repair. The lamin-based protein sub-complexes are implicated in both nuclear and cytoskeletal organization, the mechanical stability of the nucleus, genome organization, transcriptional regulation, genome stability, and cellular differentiation. Here we review recent research in the field of nuclear lamins and their role in modulating various nuclear processes and their impact on cell function.

Two ferrocene derivatives, namely, 1,2-(tetramethylene)-ferrocene and 1,2,1’,2’-bis(tetramethylene)-ferrocene, were synthesized in a four-step reaction sequence starting from ferrocene. Friedel-Craft acylation of ferrocene with succinic anhydride gave mono- or bis(3-carboxypropinoyl)ferrocene depending on the stoichiometry of succinic anhydride. The reduction of the keto groups to methylene, followed by ring-closing using trifluoroacetic anhydride gave 1,2-(α-ketotetramethylene)-ferrocene or 1,2,1’,2’-bis(α-ketotetramethylene)ferrocene. The diastereomeric mixture of the latter diketones was separated by column chromatography, characterized by single-crystal X-ray analysis, and assigned their stereochemistry. Reduction of the keto groups to methylene under Clemmensen conditions gave homoannular mono- or bis(tetramethylene) ferrocene derivatives. The molecular structure of 1,2-(tetramethylene)-ferrocene revealed that the ipso carbon atoms of the cyclopentadienyl group are 0.023(3) Å farther away from Fe(II) compared to the remaining three carbon atoms. Both complexes exhibit lower half-wave oxidation potentials than ferrocene, possibly due to the electron-releasing effects of the tetramethylene bridges.

After brings about a brief review of the theoretical explanations and researches on the reasons for being a victim, this article is organized into two sections. The first presents a comparative analysis of the data for 1999 and 2016 in terms of perceptions, profiles and most significant sociodemographic and socioeconomic variables. The second one shows an explanatory analysis based on a multivariate logistical regression model using as an independent variable lifestyle of the population and socioeconomic variables, and as dependent variables individual’s susceptibility to becoming a victim of certain crimes. The results points towards an explanatory model of victimization in which sociodemographic variables play an increasingly less important role while variables related to lifestyle and subjective perceptions make a significant contribution to greater understanding of the nature of being the victim of a crime.