Global navigation satellite system (GNSS) array antenna receivers are widely used to suppress wideband interference in navigation countermeasures. However, existing array antenna receivers all adopt digital array structure and digital beamforming technique, and it has limited analog-front-end (AFE) dynamic range. In strong interference scenarios, AFE saturation will occur, which limits the maximum interference suppression ability of the array receiver. Aiming at this issue, this paper proposes a robust wideband interference suppression method for GNSS array antenna receivers based on hybrid beamforming technique. Firstly, a novel fully connected hybrid array receiver structure is proposed; Secondly, the corresponding hybrid beamforming method is proposed at the same time, and it realizes the complete elimination of strong interference by jointly suppression in analog domain and digital domain. After mathematical simulation experiments, it is verified that compared to the digital beamforming-based anti-jamming technique, the proposed method can effectively suppress strong wideband interference, and the maximum interference suppression ability is improved by 36 dB.

The ubiquitous connectivity for the space-air-ground integrated network (SAGIN) of the beyond fifth generation of communication and sixth generation of communication (B5G/6G) is envisaged to meet the needs for the demanded quality of service (QoS), green communication, and "dual carbon" target. However, the offloading and computation of massive latency-sensitive tasks dramatically increases the energy consumption of the network. Furthermore, the traditional power supply technology of the network base stations (BSs) enhances the carbon emission. To address these issues, we first propose a SAGIN architecture with energy harvesting devices, where the BS is powered by both renewable energy (RE) and the conventional grid. The BS explores wireless power transfer (WPT) technology to power the unmanned aerial vehicle (UAV) for stable network operation. RE sharing between neighbouring BSs is designed to fully utilize RE for reduce carbon emission. Secondly, on the basis of task offloading decision, UAV trajectory, and RE sharing ratio, we construct cost functions with joint latency-oriented, energy consumption, and carbon emission. Then, we develop a twin delayed deep deterministic policy gradient (TD3PG) algorithm based on deep reinforcement learning to minimize the cost function. Finally, simulation results demonstrate that the proposed algorithm outperforms the benchmark algorithm in terms of reducing latency, energy saving, and lower carbon emission.

Space–air–ground integrated network (SAGIN) is considered as an enabler for the sixth-generation (6G) networks. By integrating terrestrial and non-terrestrial (satellite, aerial) networks, SAGIN seem to be a quite promising solution to provide reliable connectivity everywhere and all the time. Their availability can be further enhanced if hybrid free space optical (FSO)/radio frequency (RF) links are adopted. In this paper, the performance of a hybrid FSO/RF communication system operating in SAGIN has been analytically evaluated. In the considered system, a high altitude platform station (HAPS) is used to forward the satellite signal to the ground station. Moreover, the FSO channel model assumed takes into account the turbulence, pointing errors and path losses, while for the RF links, a relatively new composite fading model has been considered. In this context, a new link selection scheme has been proposed that is designed to reduced the signaling overhead required for the switching operations between the RF and FSO links. The analytical framework that has been developed is based on the Markov chain theory. Capitalizing on this framework, the performance of the system has been investigated using the criteria of outage probability and the average number of link estimations. The numerical results presented reveal that the new selection scheme offers a good compromise between performance and complexity.

As an emerging network paradigm, Space-Air-Ground integrated networks (SAGIN) has attracted the attentions from academia and industry. That is because SAGIN can implement seamless global coverage and connections among electronic devices in space, air, and ground spaces. Additionally, the shortages of computing and storage resources in mobile devices greatly affect the quality of experiences for intelligent applications. Hence, we devise to integrate SAGIN as an abundant resource pool into mobile edge computing environments (MEC). To facilitate efficient processing, we need to solve the optimal task offloading decisions. Different from the existing MEC task offloading solutions, we have to face some new challenges, such as the fluctuation of processing capability for an edge computing node, the uncertainty of the transmission latency caused by the heterogeneous network protocols, the uncertain amount of uploaded tasks during a period, and so on. In this paper, we firstly describe a task offloading decision problem in new challenge environments. But, we cannot use the standard robust optimization and stochastic optimization methods to obtain the optimal result under the uncertain network environments. In this paper, we propose the condition value at risk-aware distributionally robust optimization algorithm, named as CVAR-DRO, to solve the task offloading decision problem. The proposed CVAR-DRO method combines the distributionally robust optimization and the condition value at risk model for solving the optimal result. And then, We have evaluated our approach in simulation SAGIN environments with the confidence interval, the number of mobile task-offloading and the various parameters. We compare our proposed CVAR-DRO algorithm with the state-of-the-art algorithms, such as the standard robust optimization algorithm, the stochastic optimization algorithm, the DRO algorithm, and the brute algorithm. The experimental results show that CVAR-DRO can get a sub-optimal mobile task-offloading decision. Overall, CVAR-DRO is more robust than others to the new challenges mentioned above in SAGIN.

To analyze the combined response of ocular cyclotorsion and head tilt during body tilt and to interpret the physiologic role of those movements, each of the three subjects completed six different experiments of body tilt not fixating their head movements using a flight simulator, which consisted of combinations of three tilt angles (30, 45, and 60) and two visual conditions. Head tilt and ocular cyclotorsion of the right eye before, during, and after the tilt maneuver were recorded and analyzed by time sequence. In the active tilting phase, the right eye showed a stepladder pattern of multiple repeats of fast and slow cyclotorsion along with head tilt to obtain maximum visual information. During the stationary tilting phase, there occurred a small amount (mean, 2.3) of ocular cyclotorsion which was reciprocal to that of head tilt. The visual cue of body tilt through the central visual field induced a larger amount of head tilt but affected little ocular cyclotorsion. The maximum degree of ocular cyclotorsion during each experiment was 10.2 on average. In conclusion, the combined response of ocular cyclotorsion and head tilt develops during body tilt and it compromises the conflicting needs between binocular vision and gravitational orientation.

Recently, the Integrated Air Defense System (IADS) has become vital for the defense system as the military defense system is vital for national security. Placing Integrated Air Defense System batteries among locations to protect locations assets is a crucial problem because optimal solutions are needed for interceptor missiles to intercept attacker missiles for maximizing protection of assets across locations or places. In this research, the procedures of using network algorithms along with developing several network algorithms are going to be demonstrated to develop a model for sequential development of seven network securing strategies of placing Surface to Air Missile (SAM) batteries to maximize the protection of assets across locations (based on given asset values) by generating optimal solutions through computation to destroy maximum attacker missiles by using minimum interceptor missiles with given intercept probability. This network securing strategies can be implemented not only for Integrated Air Defense System (IADS) planning but also Counter Air (CA) planning as Integrated Air Defense System (IADS) is conducted with defensive counter air supported by attack operations in offensive counter air.

Ulcerative colitis (UC) is a chronic inflammatory disease, the incidence of which is increasing worldwide. However, the etiology and pathogenesis of UC remains unclear. The n-butanol extract of pulsatilla decoction (BEPD) of the traditional Chinese medicine herbal formula has been shown to be effective in treating UC. We aimed to explore the molecular mechanism underlying the effects of BEPD on UC, in particular its effects on neutrophil extracellular trap (NET) formation by neutrophils. High-performance liquid chromatography was used to determine the principal compounds of BEPD. UC was induced in mice using dextran sodium sulfate, and mice were treated with 20, 40, or 80 mg/kg BEPD daily for seven days. Colonic inflammation was determined by assessing the disease activity index, histopathology, colonic mucosal damage index, colonic mucosal permeability, and pro- and anti-inflammatory cytokine levels. The infiltration and activation status of neutrophils in the colon were determined by analyzing the levels of chemokine (C-X-C motif) ligand (CXCL)1 and CXCL2, reactive oxygen species, Ly6G, and numerous NET proteins. Our results showed that BEPD improved the disease activity index, histopathology, and colonic mucosal damage index scores of mice with UC, and restored colonic mucosal permeability compared with untreated mice. The expression levels of the pro-inflammatory cytokines interleukin-1β, interleukin-6, and tumor necrosis factor-α in colon tissues were significantly decreased, while the expression levels of anti-inflammatory cytokines in colon tissues were significantly increased, exceeding those of control mice. In addition, BEPD reduce the expression of the neutrophil chemokines CXCL1 and CXCL2 in the colon tissue of mice with UC, reduced neutrophil infiltration, reduced reactive oxygen species levels, and significantly reduced the expression of NET proteins. BEPD also significantly reduced NET formation. The results of this study suggest that BEPD exerts therapeutic effects in a murine model of UC by inhibiting neutrophil infiltration and activation in the colon, as well as by inhibiting the expression of key proteins involved in NET formation and reducing NET formation, thereby alleviating local tissue damage and disease manifestations.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

The design and operation of quantum networks are both decisive in the current push towards a global quantum internet. Although space-enabled quantum connectivity has already been identified as a beneficial candidate for long-range quantum channels for over two decades, the architecture of a hybrid space-ground network is still a work in progress. Here, we propose an analysis of such a network based on a best-path approach, where either fiber- or satellite-based elementary links can be concatenated to form a repeater chain. The network consisting of quantum information processing nodes, equipped with both ground and space connections, is mapped into a graph structure, where edge weights represent the achievable secret key rates, chosen as the figure of merit for the network analysis. A weight minimization algorithm allows identifying the best path dynamically, i.e., as the weather conditions, stray light radiance, and satellite orbital position changes. From the results we conclude that satellite links will play a significant role on the future large-scale quantum internet, and both a constellation of satellites and significant advances in filtering technology are required to fulfill continuous coverage.

The Axillary Seabream Pagellus acarne is of economic importance for recreational and commercial fisheries in the Atlantic and the Mediterranean, but a decline in total landings has been observed and raised some concern. Although biological information on the species has been provided for the Atlantic and Mediterranean, in the Portuguese continental slope data is restricted to the southern part of the country, which points to the relevance of the present work. A total of 520 individuals, between 7.8 cm and 39.9 cm TL, were monthly collected from September 2020 to August 2022 from commercial landings of fishing vessels operating off mainland Portugal, and used to study age and growth, the reproductive strategy and the annual sexual cycle. Age varied between 0 years (7.8 cm TL) and 15 years (34.2 cm TL) and the von Bertalanffy growth parameters were estimated from whole-otolith readings (L∞ = 35.2 cm, k = 0.133 yr–1 and t 0 = –2.78 yr). Pagellus acarne proved to be a protandric hermaphrodite species with males prevailing until 28.0 cm TL and females between 28.0 cm and 34.0 cm TL with a brief sex change phase. Females presented asynchronous oocyte development with a batch spawning pattern. The spawning season occurred from April to October with a spawning peak between June and August aas shown by histological analysis of the gonads and high levels of GSI during the period.

Addressing real-time aircraft target detection in microsatellite-based visible light remote sensing video imaging requires considering the limitations of imaging payload resolution, complex ground backgrounds, and the relative positional changes between the platform and aircraft. These factors lead to multi-scale variations in aircraft targets, making high-precision real-time detection of small targets in complex backgrounds a significant challenge for the detection algorithms. Hence, this paper introduces a real-time aircraft target detection algorithm for remote sensing imaging using an improved lightweight attention mechanism that relies on the YOLOv7 framework (SE-CBAM-YOLOv7). The proposed algorithm replaces the standard convolution (Conv) with a lightweight convolutional SEConv to reduce the computational parameters and accelerate the detection process of small aircraft targets, thus enhancing real-time onboard processing capabilities. Besides, the SEConv-based SPPCSPC (Spatial Pyramid Pooling and Connected Spatial Pyramid Convolution) module extracts image features. It improves detection accuracy while the feature fusion section integrates the CBAM hybrid attention network, forming the CBAMCAT module. Furthermore, it optimizes small aircraft target features in channel and spatial dimensions, improving the model's feature fusion capabilities. Experiments on public remote sensing datasets reveal the proposed SE-CBAM-YOLOv7 improves detection accuracy by 3% and mAP value by 4.2% compared to YOLOv7, significantly enhancing the detection capability for small-sized aircraft targets in satellite remote sensing imaging.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

To address the issue of reduced orbit estimation accuracy resulting from discrepancies between in-orbit measured geomagnetic field values and IGRF model values in autonomous orbit estimation of microsatellites based on geomagnetic field measurements, this study introduces an adaptive cubature H-infinity filtering algorithm. Firstly, it presents the low-altitude orbital dynamics model and geomagnetic field measurement model for microsatellites. Subsequently, within the adaptive cubature H-infinity filtering algorithm, a spherical simplex rule and a second-order Gaussian-Legendre quadrature criterion are employed to compute the spherical surface integral and radial integral. Additionally, a spherical simplex-radial quadrature rule is proposed to enhance the approximation accuracy of nonlinear Gaussian weighted integrals. Furthermore, by integrating extended H-infinity filtering based on game theory with the cubature quadrature rule, an inverse proportional relationship between constraint level and filtering innovation is established. This allows for adaptive adjustment of the constraint level to enhance robustness against model errors. Finally, through semi-physical simulation experiments, it is demonstrated that compared with traditional algorithms, the proposed algorithm improves autonomous orbit estimation position accuracy of microsatellites by 7.49%, while also enhancing velocity accuracy by 3.1%, thus validating its effectiveness.

Abstract: Although the pathophysiology of fibromyalgia syndrome has been better understood in recent decades, a unified model of its pathogenesis and an effective therapeutic approach are still far from being realized. The main aim of this article will be to delve into the fundamental mechanisms of the pathophysiology of fibromyalgia conceptualized as stress intolerance syndrome. Using the biopsychosocial model of chronic pain syndromes, we will describe the potential role of the attachment system, C tactile fibers, and oxytocinergic system dysfunction in the pathophysiology of fibromyalgia syndrome and other central sensitivity syndromes. At the end of the article, the therapeutic implications of this new global and translational pathophysiological model will be briefly discussed.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

We present a case of adult-onset systemic chronic active EBV disease (CAEBV) in a 40-year-old woman with chronic HBV hepatitis. Initial symptoms resembled a viral illness, progressing to recurrent fever, transaminitis, and anasarca. Investigations revealed high-level EBV viremia and an abnormal T-cell population in liver and bone marrow, indicative of CAEBV. Liver biopsy showed CD3+ T-cells lacking TCRbeta and displaying dim/negative CD5, with elevated EBV-infected T-cells. Next-generation sequencing identified rare variants in CREBBP, SPEN, TP73, and PLCG2, suggesting potential contributions to disease pathogenesis. This case underscores diagnostic challenges and management complexities of adult-onset CAEBV, particularly with underlying chronic HBV infection. Genomic profiling offers crucial insights into the molecular landscape of rare lymphoid malignancies, highlighting the importance of personalized treatment strategies. The distinct immunophenotypic features underscore the heterogeneity in EBV-associated T-cell LPDs, urging further research for optimized clinical management

There is crescent demand for knowledge improvement of the integrated water vapor (IWV) distribution in regions affected by heat islands that are associated with extreme rainfall events such as in the metropolitan area of Rio de Janeiro (MARJ). This work assessed the suitability and distribution of IWV in the MARJ using products from the Global Navigation Satellite Systems (GNSS), MODerate Resolution Imaging Spectroradiometer (MODIS), and radiosonde. GNSS data were collected by the tracking station named RDJN, from the cooperation of the International GNSS Monitoring and Assessment System (iGMAS) and the National Observatory of Brazil (Observatório Nacional - ON), and the tracking stations ONRJ, RIOD, and RJCG belonging to the Brazilian Network for Continuous Monitoring (RBMC) in the period of January 2015–August 2018. High variability of the near surface air temperature (T) and relative humidity (RH) were observed among eight meteorological sites considered. The mean T differences between sites, up to 4.4 °C, led to mean differences as high as 3.1 K for weighted mean temperature (Tm) and hence 0.83 mm for IWV differences. The performance of the MODIS MOD07 and MYD07 products provided a reasonably good representation of the mean spatial distribution of IWV, especially during the daylight passages of the satellites TERRA and AQUA. Local grid points of MODIS IWV estimates had relatively good agreement with the GNSS-derived IWV, with mean differences from -2.4–1.1 mm considering only daytime passages of the satellites TERRA and AQUA. During nighttime, MODIS underestimated IWV (from -9–-3 mm) with respect to GNSS, due to attenuation of IR radiation by clouds. A contrasting behavior was found in the radiosonde IWV estimates compared with the estimates from GNSS. There were dry biases of 1.4 mm (3.7% lower than expected) by radiosonde IWV during the daytime considering that all other estimates were unbiased and the differences between IWV GNSS and IWV RADS were consistent. Based on the IWV comparisons between radiosonde and GNSS at nighttime, the atmosphere over the radiosonde site is about 1.2 (2.3) mm wetter than over RIOD (RDJN) station. The long time series of the comparisons between IWVRDJN and IWVRIOD showed that the highest values of IWV occurred from the afternoon to nocturnal hours. Further, the atmosphere over the site RIOD was consistently about 1 mm wetter than over RDJN. These results showed the feasibility of the iGMAS RDJN station data compared with the RBMC, MODIS, and radiosonde data to investigate IWV in a region with occurrence of heat islands, and the peculiar physiographic and meteorological characteristics as in the MARJ. This work recommended the usage of complete meteorological station data collocated near every GNSS receiver aiming improvements of local GNSS IWV estimates and serving as additional support for operational numerical assimilation, weather forecast, and nowcast of extreme rainfall events.

The critical systems, which the failure and malfunction may result in human, environment and financial severe damages, are essential components in various sectors and particularly in energy domains. Although unwished, integration error problems in supervision of critical systems occurs, incurring significant expenses because of operator’s subjective analysis and on hardware topology failures. In this work, a malleable model design approach is proposed to formulate and solve the integration error problem in the critical systems supervision in terms of reliability. A real Hybrid Power Plant (HPP) case is considered as a requirement for a study case with simulated data. A method framework with informal approach (C4 diagram) and formal approach (Hierarchical Coloured Petri Nets) in radial spectrum is applied to the HPP supervision design. Using formal methods, a formulation and solution to this problem through structured, scalable and compact mathematical representations are possible. This malleable model intends to guarantee functional correctness and then reliability of the plant supervision system based on system software architecture. Outcomes suggest corroboration that the malleable model is appropriate for energy domain, and can be used for other types of critical systems, bringing all the benefits of this methodology to the context in which it will be applied.

Particulate organic carbon (POC) is a pivotal component within the marine carbon cycle, actively involved in diverse biogeochemical processes. This study focuses on Mediterranean as the research region, selecting the most influential factors from 47 potential ones influencing surface POC. Using geographic detector for factor identification, ten primary influencers were identified. Preliminarily optimized random forest (BRF), backpropagation neural network, adaptive boosting, and extreme gradient boosting were utilized to construct POC assessment models. Notably BRF exhibited superior performance in estimating the sea surface POC. Further optimization of RF using the tuneRanger R package resulted in R² of 0.868, mean squared error of 1.119 (mg/m³) ², and mean absolute error of 1.041 (mg/m³). Surface POC concentrations in the Mediterranean for May and June 2017 were estimated. Spatial distribution analysis unveiled higher concentrations in the west, lower in the east, higher in the north, lower in the south, with higher levels near the coast and lower far from the coast. Additionally, the study deliberated on the impact of human activities on surface POC in the Mediterranean. This research contributes a high-precision method for satellite retrieval of surface POC concentrations in the Mediterranean, thereby enriching the understanding of POC dynamics in the area.

Understanding the structural intricacies of RNA molecules is essential for deciphering numerous biological processes. Traditionally, scientists have relied on experimental methods to gain insights and draw conclusions. However, the recent advent of advanced computational techniques has significantly accelerated and refined the accuracy of research results in several areas. A particularly challenging aspect of RNA analysis is the prediction of its secondary structure, which is crucial for elucidating its functional role in biological systems. This paper deals with the prediction of pseudoknots in RNA, focusing on two types of pseudoknots: K-type and M-type pseudoknots. Pseudoknots are complex RNA formations in which nucleotides in a loop form base pairs with nucleotides outside the loop and thus contribute to essential biological functions. Accurate prediction of these structures is crucial for understanding RNA dynamics and interactions. Building on our previous work in which we developed a framework for the recognition of H- and L-type pseudoknots, an extended grammar-based framework tailored to the prediction of K- and M-type pseudoknots is proposed. This approach uses syntactic pattern recognition techniques and provides a systematic method to identify and characterize these complex RNA structures. Our framework uses context-free grammars (CFGs) to model RNA sequences and predict the occurrence of pseudoknots. By formulating specific grammatical rules for type K and type M pseudoknots, we enable efficient parsing of RNA sequences to recognize potential pseudoknot configurations. This method ensures an exhaustive exploration of possible pseudoknot structures within a reasonable time frame. In addition, the proposed method incorporates essential concepts of biology, such as base pairing optimization and free energy reduction, to improve the accuracy of pseudoknot prediction. These principles are crucial to ensure that the predicted structures are biologically plausible. By embedding these principles into our grammar-based framework, we aim to predict RNA conformations that are both theoretically sound and biologically relevant.

Plato defined a quality as “some degree of perfection” [49]. Studies on quality have unveiled the internal and external quality factors [17] that significantly impact product quality [4]. Internal factors are invisible to the end customer and are dependent on overall work organisation by the development team [17]. This work organisation is called “the process” [11],[33]. In this article, we will discuss how to address the drone-dedicated software development process to support system verification and ensure product quality by supporting quality characteristics and therefore increase software development awareness and control. We will discuss the process's influence on overall work activities and relationships between those activities by addressing the software development process utilised in the drone-dedicated GNSS-denied navigation system development project. The result was observable after three weeks of starting the software development. It was focused on better team awareness, faster task completion, lower number of development mistakes, and better and faster change response than we observed in other projects that didn’t follow the predefined process.

Atopic dermatitis (AD) is a chronic inflammatory disorder presenting a dysregulated immune response and derangement of the epidermal barrier lipids. The Th2-type cytokines interleukin IL-4 and IL-13 play a prominent role in AD by activating the Janus Kinase/Signal Transduction and Activator of Transcription (JAK/STAT) intracellular signal axis. This study aimed to investigate the role of JAK/STAT in the lipid perturbations induced by Th2 signaling in 3D-epidermal equivalents. We used tofacitinib, a low-molecular-mass JAK inhibitor, to screen for the JAK/STAT-mediated deregulation of lipid metabolism. Th2 cytokines decreased the expression of elongases 1, 3, and 4, and serine-palmitoyl-transferase and increased that of sphingolipid delta(4)-desaturase, and carbonic anhydrase 2. Th2 cytokines inhibited the synthesis of palmitate and caused a depletion of triglycerides. This depletion was associated with altered PC profiles and fatty acid (FA) metabolism. Overall, the ceramide profiles were minimally affected. Except for most sphingolipids and very long chain FAs, the effects of Th2 on lipid pathways were reversed by co-treatment with tofacitinib. An increase in the mRNA levels of CPT1A and ACAT1, reduced by tofacitinib, suggests that Th2 cytokines promote FA beta-oxidation. In conclusion, pharmacological inhibition of JAK/STAT activation prevents the lipid disruption caused by halted homeostasis of FA metabolism.

Dark energy and dark matter are described as different manifestations of vacuum energy in a new cyclic universe framework of Extra Dimensional Symmetry (EDS) that doubles large spatial dimensions with microscopic partners. In this testable framework, vacuum energy, constrained by a Planck density constraint, exists in a gravitationally dark state where actual gravitational constant G_o = 0G. While a small repulsive component is constrained by an asymptotically evolving asymmetry to the active state where G_o = 2G, some components in the inert state are enabled to gravitationally attract by neutrino induced gravitational constant with light and shear activated heavy components. Observational and experimental tests are briefly discussed.

In recent years, research on adversarial attack techniques for remote sensing object detection (RSOD) has made great progress. Still, most of the research nowadays is on end-to-end attacks, which mainly design adversarial perturbations based on the prediction information of the object detectors (ODs) to achieve the attack. These methods do not discover the common vulnerabilities of the ODs and thus the transferability is weak. Based on this, this paper proposes a foreground feature approximation (FFA) method to generate adversarial examples (AEs) that discover the common vulnerabilities of the ODs by changing the feature information carried by the image itself to implement the attack. Specifically, firstly, the high-quality predictions are filtered as attacked objects using the detector, after which a hybrid image without any target is made, and the hybrid foreground is created based on the attacked targets. The images' shallow features are extracted using the backbone network, and the features of the input foreground are approximated towards the hybrid foreground to implement the attack. In contrast, the model predictions are used to assist in realizing the attack. In addition, we have found the effectiveness of FFA for targeted attacks, and replacing the hybrid foreground with the targeted foreground can realize targeted attacks. Extensive experiments with seven rotating ODs on the RSOD datasets DOTA and UCAS-AOD show that FFA achieves both targetless and targeted attacks with a high success rate and transferability.

The AUC-ROC is a widespread measure to assess the performance of a binary classification model across various discrimination thresholds. Yet, it is not apt for unbalanced class problems and is misleading for early retrieval. For instance, link prediction in complex networks is an unbalanced early retrieval problem, whose goal is to offer a ranking of the nonobserved network links, prioritizing a small cohort of positive links (for which we are sure the labels are reliable) on top of a list largely populated by unlabeled links (for which the labels are uncertain). Differently from binary classification, here the evaluation focuses on how the predictor prioritizes the positive class, because the negative class does not exist and is replaced by an unlabeled class. For decades, scholars have been investigating the necessity to correct and to generalize the AUC-ROC to work for both unbalanced classification and early retrieval evaluation, this is requested in many applied domains of computational science. Here we propose the area under the magnified ROC (AUC-mROC), a new measure that adjusts the standard AUC-ROC to work for unbalanced early retrieval problems such as link prediction. Finally, we introduce the area under the generalized ROC (AUC-gROC), which unifies both AUC-mROC and AUC-ROC to provide a universal and reliable evaluation measure that can work for both classification and early retrieval problems, regardless of class proportion.This discovery represents a critical achievement, culminating in success after decades of contentious research. Its solution promises to significantly impact various domains within applied computational science.

This paper represents the first investigation into the consensus problem of linear time-varying multi-agent systems utilizing an event-triggered communication scheme. First, a general event-triggered consensus control scheme is proposed for a general category of linear time-varying multi-agent systems. Under some suitable assumptions, it is demonstrated that all agents’ states will converge exponentially, with Zeno behaviour being ruled out. Second, the consensus problem in a network of linear time-varying multi-agent systems with a spanning tree is investigated using the proposed control strategy. It demonstrates that the consensus issue for the specified system can be reformulated as a stabilization problem for an error system through a time-varying linear transformation. Then, the event-triggered consensus problem is just a special instance of the general event-triggered consensus problem mentioned above. Finally, to illustrate the efficacy of the event-triggered method proposed in this study, simulation results are shown.

The Double Diaphragm Forming (DDF) process uses vacuum pressure and heat to pre-shape composite reinforcements between flexible diaphragms. Accurate modelling of heat transfer within DDF requires knowledge of the thermophysical properties of the constituent materials. This study investigates the specific heat and thermal conductivity of silicone diaphragms, carbon fibers (chopped and powdered), thermoplastic veils, and their combinations. Experiments measured the specific heat of each material using differential scanning calorimetry and the thermal conductivity of silicone and carbon fabric preforms using the transient plane source method and modified transient plane source method respectively. The influence of reheating cycles on specific heat of carbon fiber-veil samples and the effect of compaction on thermal conductivity of silicone and carbon fabrics were explored. While silicone exhibited linear specific heat behavior, the thermoplastic veil showed non-linearity due to phase change. The combined carbon fiber-veil samples demonstrated slight non-linear specific heat variations depending on reheating cycles. Thermal conductivity of the fabric preforms decreased with the addition of thermoplastic veil and under vacuum-compaction conditions. The established temperature-dependent property relationships provide valuable data for optimizing DDF preforming parameters and enhancing energy efficiency in composite manufacturing.

The Hindu Kush Himalaya (HKH) is one of the most flood-prone regions in the world, yet heavy cloud cover and limited in-situ observations have hampered efforts to monitor the impact of heavy rainfall, flooding, and inundation during severe weather events. This paper introduces HydroSAR, a Sentinel-1 SAR-based hazard monitoring service that was co-developed with in-region partners to provide year-round, low-latency weather-hazards information across the HKH. The paper describes the end-user focused concept and overall design of the HydroSAR service. It introduces the main processing algorithms behind HydroSAR’s broad product portfolio, which includes qualitative visual layers as well as quantitative products measuring surface water extent and water depth. We summarize the cloud-based implementation of the developed service, which is providing capability to scale automatically with event size. A performance assessment of our quantitative algorithms is described, demonstrating capabilities to map flood extent and water depth at an accuracy of >90% and

Crop productivity is directly dependent to soil fertility. High soil organic carbon (SOC) content in soil is vital as it leads to improved soil quality, increased productivity, and stable soil-aggregates. In addition, with the signing of the climate agreement, there is growing interest in carbon sequestration in landscapes. This paper looks at how SOC can be increased so that it not only contributes to reduction of CO₂, but also translates to increased food production thereby enhancing food security. This synergy between mitigation and enhancing food security is even more relevant for mountain landscapes of the Hindu Kush Himalayan (HKH) region where there remains huge potential to increase CO₂ sequestration and simultaneously address food security in the chronic food deficit villages. Soil samples were collected from seven transects each in Bajhang and Mustang and from 4 land use types in each transect. Samples of soils were taken from two depths in each plot; 0-15 cm below the soil surface and 15-30 cm below the soil surface to compare the top soil and subsoil dynamics of the soil nutrients. The lab analysis was performed to assess the soil texture, soil color, soil acidity in 'power of hydrogen' (pH), macro-nutrients as soil fertility. Secondary data was used to analyze the level of food deficit in the villages. The result shows that most of the sample soils from Mustang were clay (82.1%) which is 46 samples out of 56. The pH value of soil from Bajhang ranged from 5.29 to 9.09. The pH value of soil ranged from 5.65 to 8.81 in Mustang. SOC contents of sampled soils from Bajhang ranged from 0.20% to 7.69% with mean amount of 2.47% ± 0.17. SOC contents of sampled soils from Mustang ranged from 0.51% to 8.56% with mean amount of 2.60% ± 0.25. By land use type, forest land had the highest carbon (C) content of 53.61 t ha^-1 in Bajhang whereas in Mustang, agricultural land had the highest C content of 52.02 tons ha-1. Based on these data, we can say that there is potential for increasing SOC through improved soil health and crop production and soil. Sustainable soil management should be practiced for higher productivity. Livestock may also provide farmyard manure, which can be used to fertilize cultivated soils, which increases soil productivity. Increasing productivity would aid in increasing the access and availability of food in these mountain villages.

The many-body problem in quantum physics originates from the difficulty of describing the non-trivial correlations encoded in the exponential complexity of the many-body wave function. Motivated by the Giuseppe Carleo's work titled solving the quantum many-body problem with artificial neural networks [Science, 2017, 355: 602], we focus on finding the NNQS approximation of the unknown ground state of a given Hamiltonian $H$ in terms of the best relative error and explore the influences of sum, tensor product, local unitary of Hamiltonians on the best relative error. Besides, we illustrate our method with some examples.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

The study of the change in entropy during the formation of stars in collapsing molecular clouds is an important area of research in astrophysics. As the cloud decreases in size, the presence of gases leads to an increase in entropy. However, the extent of this change in entropy is influenced by the amount of space available for the gases. In this scientific investigation, I conduct a detailed analysis of entropy on a small scale within the contracting cloud, following the principles of the second law of thermodynamics. Initially, my focus is on a turbulent cloud composed of N particles with a mass of M, which collapses under the force of gravity. It becomes clear that in order for the collapse to occur, gravitational energy must overcome other pressure forces that oppose it. This process results in the rapid movement of particles within the cloud, ultimately leading to a change in entropy

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

Aiming at solving difficulties related to aero-engine classification and identification, the infrared spectra of aero-engine hot jets are measured by telemetry Fourier transform infrared spectrometer, and a six types aero-engine hot jet spectrum data set is generated. The spectrum data set were randomly sampled at a ratio of 8:1:1 to generate training set, validation set and prediction set. In this paper, a Peak Finding Siamese Convolutional Neural Network (PF-SCNN) is designed to match and classify spectrum data. In the first place, the matching pairs of training set and validation set are made independently with the labels of positive and negative samples creating. The spectrum feature extraction and distance similarity calculation are carried out by the Siamese convolutional neural network (SCNN). When entering the prediction phase, the prediction set and training set are integrated to predict in the trained model. The prediction set labels are ultimately determined by matching them with the training set labels having the highest similarities to ensure accurate predictions. To improve the operation efficiency of the SCNN, a peak finding method is introduced to extract the spectrum peaks. Peak positions of high frequency are counted, while the peak data are extracted. The peak data are used to take the place of the original data for training and prediction. The performance measures are defined as Accuracy, Precision, Recall, Confusion matrix and F1-score, and the prediction accuracy was up to 99%. The experimental results indicate that the proposed PF-SCNN is suitable for our spectral dataset and can complete the task of infrared spectrum classification of aero-engine hot jets.

Focusing on the problem of identifying and classifying aero-engine models, this paper measures the infrared spectrum data of aero-engine hot jets using a telemetry Fourier transform infrared spectrometer. Simultaneously, infrared spectral data sets with the six different types of aero-engines are created. For the purpose of classifying and identifying infrared spectral data, a CNN architecture based on the continuous wavelet transform peak seeking attention mechanism (CWT-AM-CNN) is suggested. This method calculates the peak value of middle wave band by continuous wavelet transform, and the peak data is extracted by the statistics of the wave number locations with high frequency. Attention mechanism is used for the peak data, and the attention mechanism is weighted to the feature map of the feature extraction block. The training set, vali-dation set and prediction set are divided in the ratio of 8:1:1 for the infrared spectral data sets. For three different data sets, CWT-AM-CNN proposed in this paper is compared with the classical classifier algorithm based on CO2 feature vector and the popular AE, RNN and LSTM spectral processing networks. The prediction accuracy of the proposed algorithm in the three data sets is as high as 97%, and the lightweight network structure design not only guarantees high precision, but also has a fast running speed, which can realize the rapid and high-precision classification of the infrared spectral data of the aero-engine hot jets.

Ice formation on aircraft surfaces poses significant safety risks, and current detection systems often struggle to provide accurate, real-time predictions. This paper presents the development and comprehensive evaluation of a smart ice control system using a suite of machine learning models. The system utilizes various sensors to detect temperature anomalies and signal potential ice formation. We trained and tested supervised learning models (Logistic Regression, Support Vector Machine, Random Forest), unsupervised learning models (K-means clustering), and neural networks (Multi-Layer Perceptron) to predict and identify ice formation patterns. Experimental results demonstrate that our smart system, driven by machine learning, accurately predicts ice formation in real-time, optimizes de-icing processes, and enhances safety while reducing power consumption. This solution holds the potential for improving ice detection accuracy in aviation and other critical industries requiring robust predictive maintenance.

Recurrent sunspot groups were studied by using the Debrecen Photoheliographic Data (DPD) which covers more than 40 years. For this task it is necessary to make unambiguous the identification of the returning solar active regions. It starts with an algorithmic listing of possible returns, then the candidates of the algorithmic identifications are checked by the unique HTML-feature of the DPD. The final check is the application of an asymmetric Gaussian function introduced in previous articles to describe the development of short-lived sunspot groups observed continuously from start to end on the visible solar disc. The data of correctly identified recurrent sunspot groups fit surprisingly well to this function throughout the rotations enabling the reconstruction of the development also on the far side of the sun. The primary goal was to find any relationship between the maximum area and the lifetime deduced from the data of the asymmetric curves. This relationship is more complex than earlier results in the literature for short-lived groups. The lifetimes exhibit weak dependencies on the heliographic latitude and solar cycle phase. An apparently returning active area is rather an active nest if its data do not fit to the asymmetric Gaussian.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

Sparse training (ST) aims to ameliorate deep learning by replacing fully connected artificial neural networks (ANNs) with sparse or ultra-sparse ones, such as brain networks are, therefore it might benefit to borrow brain-inspired learning paradigms from complex network intelligence theory. Here, we launch the ultra-sparse advantage challenge, whose goal is to offer evidence on the extent to which ultra-sparse (around 1% connection retained) topologies can achieve any leaning advantage against fully connected. Epitopological learning is a field of network science and complex network intelligence that studies how to implement learning on complex networks by changing the shape of their connectivity structure (epitopological plasticity). One way to implement Epitopological (epi- means new) Learning is via link prediction: predicting the likelihood of non-observed links to appear in the network. Cannistraci-Hebb learning theory inspired the CH3-L3 network automata rule for link prediction which is effective for general-purpose link prediction. Here, starting from CH3-L3 we propose Epitopological Sparse Meta-deep Learning (ESML) to apply Epitopological Learning to sparse training. In empirical experiments, we find that ESML learns ANNs with ultra-sparse hyperbolic (epi-)topology in which emerges a community layer organization that is meta-deep (meaning that each layer also has an internal depth due to power-law node hierarchy). Furthermore, we discover that ESML can in many cases automatically sparse the neurons during training (arriving even to 30% neurons left in hidden layers), this process of node dynamic removal is called percolation. Starting from this network science evidence, we design Cannistraci-Hebb training (CHT), a 4-step training methodology that puts ESML at its heart. We conduct experiments on 7 datasets and 5 network structures comparing CHT to dynamic sparse training SOTA algorithms and the fully connected counterparts. The results indicate that, with a mere 1% of links retained during training, CHT surpasses fully connected networks on VGG16, GoogLeNet, ResNet50, and ResNet152. This key finding is an evidence for ultra-sparse advantage and signs a milestone in deep learning. CHT acts akin to a gradient-free oracle that adopts CH3-L3-based epitopological learning to guide the placement of new links in the ultra-sparse network topology to facilitate sparse-weight gradient learning, and this in turn reduces the convergence time of ultra-sparse training. Finally, CHT offers the first examples of parsimony dynamic sparse training because, in many datasets, it can retain network performance by percolating and significantly reducing the node network size. Our code is available at: https://github.com/biomedical-cybernetics/Cannistraci-Hebb-training.

Graft injury affects over 50% of liver transplant (LT) recipients, but non-invasive biomarkers to diagnose and guide treatment are currently limited. We aimed to develop a biomarker of graft injury by integrating serum metabolomic profiles with clinical variables. Serum from 55 LT recipients with biopsy confirmed metabolic-dysfunction associated steatohepatitis (MASH), T-cell mediated rejection (TCMR) and biliary complications was collected and processed using a combination of LC-MS/MS assay. The metabolomic profiles were integrated with clinical information using a multi-class Machine Learning (ML) classifier. The efficacy of the model was assessed through the evaluation of the Out-of-Bag (OOB) error estimate. Our ML model yielded an overall accuracy of 79.66% with an OOB estimate of the error rate at 19.75%. The model exhibited a maximum ability to distinguish MASH, with an OOB error estimate of 7.4% compared to 22.2% for biliary and 29.6% for TCMR. The metabolites serine and serotonin emerged as the topmost predictors. When predicting binary outcomes using 3 models: Biliary (biliary vs. rest), MASH (MASH vs. rest) and TCMR (TCMR vs. rest), the AUCs were 0.882, 0.972 and 0.96 respectively. Our ML tool integrating serum metabolites with clinical variables shows promise as a non-invasive, multi-class serum biomarker of graft pathology.

To overcome the time-consuming drawbacks of Computational Fluid Dynamics (CFD) numerical simulations, this paper proposes a hybrid model based on a parallel architecture based on the concept of intelligent aerodynamics, named PA-TLA (Parallel Architecture combining TCN, LSTM, and Attention mechanism). This model utilizes CFD data to drive efficient predictions of aircraft wake evolution at different initial altitudes during the approach phase. Initially, CFD simulations of continuous initial altitudes during the approach phase are used to generate aircraft wake evolution data, which are then validated against real-world LIDAR data to verify their reliability. The PA-TLA model is designed based on a parallel architecture, combining Long Short-Term Memory networks (LSTM), Temporal Convolutional Networks (TCN), and a tensor concatenation module based on the attention mechanism, which ensures computational efficiency while fully leveraging the advantages of each component in a parallel processing framework. The study results show that the PA-TLA model outperforms both the LSTM and TCN models in predicting the three characteristic parameters of aircraft wake: vorticity, circulation, and Q-criterion. Compared to the serially structured TCN-LSTM, PA-TLA achieves an average reduction in mean squared error (MSE) by 6.80%, mean absolute error (MAE) by 7.70%, and root mean square error (RMSE) by 4.47%, with an average increase in the coefficient of determination (R²) by 0.36%, and a 35% improvement in prediction efficiency. Lastly, this study combines numerical simulation and the PA-TLA deep learning architecture to analyze the characteristics of wake evolution during the near-ground phase, providing theoretical value for further reducing aircraft wake intervals and enhancing airport operational efficiency.

Mechanical equipment is composed of several parts, the interaction between the parts exists throughout whole life cycle leads to the widespread phenomenon of fault coupling and the diagnosis of independent faults cannot meet the requirements of the health management of mechanical equipment under actual working conditions. In this paper, the topological structure of graph neural network is used to describe the correlation of coupling faults and multiple fault types are regarded as network nodes respectively. The fault features are fused and extracted by graph convolution to achieve the classification of coupling faults. In this paper, dynamic vertexes are defined in data topology and the parameters of DIGNN classification model are optimized by changing the fault type of dynamic vertexes during training stage. The data is loaded into dynamic vertexes for classification and analysis during testing stage. The one-dimensional vibration data is converted into two-dimensional time-frequency domain data by wavelet transform making the input features of the model interpretable to reduce the uncertainty of model training. The data topology is then fed into DIGNN for fault classification, and GCN's node aggregation gives interpretability to each layer of network data processing. The method proposed in this paper can realize accurate diagnosis of independent faults on the data set, and can effectively judge the coupling mode of coupling faults, which is suitable for coupling fault analysis of mechanical equipment.

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

This paper presents an approach to improve the robustness of tip-tilt controllers for fast-steering mirror (FSM)-based laser beam steering (LBS) systems in the presence of dynamic disturbances such as external shocks. To this end, we propose the addition of a disturbance observer (DOB)-based anti-shock controller in parallel to the original linear servo control loop to improve its control performance in the presence of external shocks. To increase the tip-tilt control performance against external shocks, the DOB-based control method, which is an improved control method for eliminating nonperiodic disturbances, is implemented in the original tip-tilt control system. Results indicate that the control error of the DOB-based anti-shock controller decreased, resulting in an efficient improvement in its disturbance-rejection performance.

This study presents an effective control algorithm to improve the robustness of fast steering mirror (FSM)-based laser beam steering systems against dynamic disturbances such as repetitive disturbances resulting from operating conditions. A stable control system must be able to maintain the required high-precision control even when dynamic disturbances affect the FSM system. In this study, an improved control method is proposed using an internal model principle (IMP)-based nonlinear controller with a disturbance observer (DOB) for the FSM system. This IMP-based controller with DOB can attenuate the residual control error signal under dynamic disturbance conditions.

Parasomnias are a group of sleep disorders characterized by abnormal and unpleasant motor, verbal or behavioral events that occur during sleep or during transitions between wake and sleep states. They disrupt sleep and can have a detrimental impact on the individual experiencing them. Our goal was to identify types of parasomnias and their prevalence in the post-secondary student population and to explore students' coping strategies for parasomnias they found distressing. Seventy-seven post-secondary students completed the 21-item Munich Parasomnia Screening (MUPS) frequency scale. They also rated, on a 10-point scale, how disturbing each parasomnia was. Not only did 92% percent of students report at least one parasomnia, but our results also indicate that the vast majority of students experienced more than one parasomnia. This led us to investigate the likelihood of the co-occurrence of different parasomnias. With respect to the level of subjectively experienced distress, the most prevalent parasomnias were not always the more disturbing ones. Coded open-ended responses about what students do about the disturbing parasomnias indicate that grounding strategies and physical manipulation of one’s body were the most common, although most participants indicated that in spite of distress, they do nothing to cope. In conclusion, our study found a strikingly high prevalence of parasomnias in this sample of young adults and a lack of knowledge about effective means of dealing with these.

Dynamic sparse training is an effective strategy to alleviate the training and inference demands of artificial neural networks. However, current sparse training methods face a challenge in achieving high levels of sparsity while maintaining performance comparable to that of their fully connected counterparts. The Cannistraci-Hebb training (CHT) method produces an ultra-sparse advantage compared to fully connected training in various tasks by using a gradient-free link regrowth method, which relies solely on the network topology. However, its rigid selection based on link prediction scores may lead to epitopological local minima, especially at the beginning of the training process when the network topology might be noisy and unreliable. In this article, we introduce the Cannistraci-Hebb training soft rule (CHTs), which applies a flexible approach to both the removal and regrowth of links during training, fostering a balance between exploring and exploiting network topology. Additionally, we investigate the network topology initialization using several approaches, including the bipartite scale-free and bipartite small-world network models. Empirical results show that CHTs can surpass the performance of fully connected networks with MLP architecture by using only 1% of the connections (99% sparsity) on the MNIST, EMNIST, and Fashion MNIST datasets and can provide remarkable results with only 0.1% of the links (99.9% sparsity). In some MLPs for image classification tasks, CHTs can reduce the active neuron network size to 20% of the original nodes (neurons), demonstrating a remarkable ability to generalize better than fully connected architectures, reducing the entire model size. This represents a relevant result for dynamic sparse training. Finally, we present evidence from larger network models such as Transformers, with 10% of the connections (90% sparsity), where CHTs outperform other prevalent dynamic sparse training methods in machine translation tasks.

We present an analysis of high-resolution, near-infrared (NIR) spectra relative to the solar transit of Venus of 5-6 June 2012, as observed with the Facility Infrared Spectropolarimeter (FIRS) at the Dunn Solar Telescope in New Mexico. These observations offer the unique opportunity to probe the upper layers (between ∼84 and 150 km in altitude) of a thick, CO2-dominated atmosphere with the transmission spectroscopy technique – a proxy for future studies of highly-irradiated atmospheres of Earth-sized exoplanets. We were able to visually identify absorption lines from the two most abundant CO2 isotopologues, and from the main isotopologue of CO in the retrieved spectrum of Venus. Furthermore, we perform a cross-correlation analysis of the transmission spectrum using transmission templates generated with petitRADTRANS. With the cross-correlation technique, it was possible to confirm detections of both CO2 isotopologues and CO. Additionally, we retrieve a cross-correlation signal for O3 on Venus. We demonstrate the feasibility of high-resolution, ground-based observations to study the chemical inventory of planetary atmospheres, employing techniques commonly used in exoplanet characterization.

Background. Gene rearrangements affecting KMT2A are frequent in acute myeloid leukemia (AML) and are often associated with a poor prognosis. KMT2A gene fusions are often detected by chromosome banding analysis and confirmed by fluorescence in-situ hybridization. However, small intragenic insertions, termed KMT2A partial tandem duplication (PTD), are particularly challenging to detect using standard molecular and cytogenetic approaches. Methods. We have validated the use of a custom hybrid capture based next-generation sequencing (NGS) panel for comprehensive profiling of AML patients seen at our institution. This NGS panel targets the entire consensus coding DNA sequence of KMT2A; to deduce the presence of a PTD we used the relative ratio of KMT2A exons coverage. We sought to corroborate the KMT2A-PTD NGS results using (1) multiplex-ligation probe amplification (MLPA) and (2) optical genome mapping (OGM). Results. We analyzed 932 AML cases and identified 41 individuals harboring a KMT2A-PTD. MLPA, NGS and OGM confirmed the presence of a KMT2A-PTD in 22 of the cases analyzed where orthogonal testing was possible. Two false positive PTD calls by NGS could be explained by the presence of cryptic structural variants impacting KMT2A and interfering with PTD analysis. OGM revealed the nature of these previously undetected gene rearrangements in KMT2A, while MLPA yielded in-conclusive results. MLPA analysis for KMT2A-PTD is limited to exon 4, whereas NGS and OGM resolved KMT2A-PTD sizes and copy number levels. Conclusion. KMT2A-PTDs are complex gene rearrangements that cannot be fully ascertained using a single genomic platform. MLPA, NGS panels and OGM are complementary technologies applied in standard of care testing for AML patients. MLPA and NGS panels are designed for targeted copy number analysis; however, our results show that integration of concurrent genomic alterations is needed for accurate KMT2A-PTD identification. Unbalanced chromosomal rearrangements overlapping with KMT2A can interfere with the diagnostic sensitivity and specificity of copy number based KMT2A-PTD detection methodologies.

Urban tourism has witnessed significant growth in recent years, driven by various factors that foster the transformation of urban areas into tourist hotspots. These factors include a rising interest in culture and heritage, ongoing urban redevelopment and conversion processes, and the introduction of new experiences and activities. Two particularly influential factors contributing to this growth are low-cost travel, which facilitates more accessible access to urban destinations, and the emergence of new types of accommodation, such as short-term rental (also known as local accommodation or Airbnb-type accommodation). This sudden and continuous growth of this type of tourist accommodation brings new challenges to cities and local communities. On the positive side, it contributes to job opportunities, the dynamism of the local economy, and urban revitalization. On the other hand, it also represents more difficulty in retaining the local population in city centers, as more and more buildings are converted into hostels and tourist apartments. In this context, it becomes essential to conduct studies evaluating the impacts of these dynamics in urban areas and how they influence residents' and visitors' perspectives. Therefore, this study aims to identify the main transformations resulting from short-term rental (STR) development, focusing on the impacts felt by tourists and residents in Porto. A questionnaire was distributed to tourists and residents in Porto's city center in June 2023. The results reveal differences in opinions between tourists and residents, particularly concerning historical heritage preservation, local population relocation, and reduced housing availability for residents. Nevertheless, there is a similarity in their opinions regarding the stimulus that local accommodation brings to the economy and the rehabilitation of buildings and urban areas. This study reinforces the need to pay more attention to the future development of tourist accommodation in city centers, especially regarding local policies and territorial planning, to balance better tourism development and local communities' quality of life.

Introduction: In Traditional Chinese Medicine (TCM), tongue diagnosis plays an important role. Besides shape, colour and textural attributes of tongue regions have significance due to their association with different organs (viz. heart, lung, kidney-bladder, liver-gallbladder and stomach-spleen) in health and disease. Although numerous quantitative methods have been proposed to reduce inter and intra observer variability in tongue diagnosis, almost all of them considered only global colour/ textural features i.e. from entire body of tongue. In this work, regional colour and texture information of tongue have been analysed for healthy subjects (NOM) and patients suffering from chronic acidity-indigestion (ACD). Methods: Tongue boundaries are marked manually in each image and then tongue bodies are automatically partitioned into five regions linked with said internal organs. Rough assessments of regions’ boundaries are obtained from literature and then they are fine-tuned according to experts’ advice. As boundaries are not well defined, regions near the common boundary of two or more organs, are not assigned to any organ. Several first and second order statistical features based on grey scale intensities and a* values of LAB colour space (indicative of redness) have been extracted from five different regions of tongue images. Intragroup analysis using Wilcoxon signed rank test compared different regions within individual study group. Additionally, intergroup analysis using Wilcoxon rank sum test compared tongues of NOM with ACD for each region separately. Results: Intragroup analysis reveals a* values are statistically different (p<0.01) between stomach-spleen and liver-gallbladder regions for ACD while no significant change of a* are noted between these regions of normal tongue. It was found from intergroup analysis that correlation (one of the second order texture features extracted from grey scale images) of heart region has significantly decreased while correlation of kidney, liver-gallbladder and stomach-spleen regions significantly increased from NOM to ACD. Conclusion: This study sheds light on importance of inclusion of regional textural analysis of tongue in quantitative studies and can be applied to automated tongue diagnosis for other diseases.

Recent discoveries of potential ice particles and ice-cemented regolith on celestial bodies like the Moon and Mars have ushered in new opportunities for developing technologies to extract water, facilitating future space missions and activities on these celestial surfaces. This study delves into the potential for water extraction from regolith through an experiment designed to test water recuperation from regolith simulant under varying gravitational conditions. The resultant water vapor extracted from the regolith is re-condensed on a substrate surface and collected in liquid form. Three types of substrates, hydrophobic, hydrophilic, and grooved, are explored. The system’s functionality was assessed during a parabolic flight campaign simulating three distinct gravity levels: microgravity, lunar gravity, and Martian gravity. Our findings reveal that the hydrophobic surface demonstrates the highest efficiency due to drop-wise condensation, and lower gravity levels result in increased water condensation on the substrates. This experiment aims to provide insights into in-situ water recovery, which is pivotal for establishing economically-sustainable water supplies for future missions.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

Many studies utilize sensors to measure foot plantar pressure and analyze gait patterns, often focusing on assessing weight-bearing symmetry or asymmetry compared to control groups. However, a critical question arises: does the selection of the control group significantly impact study outcomes? Does chronic low back pain affect foot plantar pressure measurements? This experimental study involved 23 participants, including healthy individuals and those without foot disorders but with chronic low back pain. Dynamic foot pressure measurements were conducted using the Ortopiezometr, and data were analyzed using the "Steps" program. Participants were divided into two groups: Group 1 comprised completely healthy individuals, while Group 2 consisted of individuals without foot problems but with moderate chronic low back pain. The findings highlight a prevalence of energy release in the forefoot sensors compared to the hindfoot for both the right and left legs in most cases. Even among healthy volunteers, achieving perfect symmetry in the maximum values on the sensors for the right and left feet was a challenge. Results showed no statistically significant differences in energy released on specific sensors or duration of gait phases between the groups. Essentially, this suggests that foot pressure patterns are comparable between healthy individuals and those with low back pain. The use of sensor-equipped inserts for pedobarographic examinations indicates that, in cases of degenerative changes in the lumbar and sacral spine without accompanying acute pain, gait patterns resemble those of the healthy population.

Hyperspectral small target detection (HSTD) is a promising pixel-level detection task. However, due to the low contrast and imbalance number between the target and background spatially and high dimensions spectrally, it is a challenging one. To address these issues, this work proposes a representation learning-based graph and generative network for hyperspectral small target detection. The model builds a fusion network through frequency representation for HSTD, where the novel architecture incorporates irregular topological data and the spatial-spectral feature to improve its representation ability. Firstly, a graph convolutional network (GCN) module better models the non-local topological relationship between samples to represent the hyperspectral scene’s underlying data structure. The mini-batch-training pattern of the GCN decreases the high computational cost of building an adjacency matrix for high-dimensional data sets. In parallel, the generative model enhances the differentiation reconstruction and the deep feature representation ability with respect to the target spectral signature. Finally, a fusion module compensates for the extracted different types of HS features and integrates their complementary merits for hyperspectral data interpretation while increasing detection and background suppression capabilities. Experiments on different hyperspectral data sets demonstrate the advantages of the proposed architecture.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

Unmanned Aerial Vehicles (UAVs) equipped with hyperspectral imagers have emerged as an essential technology for the characterization of inland water bodies. The high spectral and spatial resolutions of these systems enable the retrieval of a plethora of optically-active water quality parameters via band ratio algorithms and machine learning methods. However, fitting and validating these models requires access to sufficient quantities of in situ reference data which are time-consuming and expensive to obtain. In this study, we demonstrate how the Generative Topographic Mapping (GTM), a Bayesian realization of the Self-organizing Map, can be used to visualize high-dimensional hyperspectral imagery and extract spectral signatures corresponding to unique endmembers present in the water. Using data collected across a North Texas pond, we first apply the GTM to visualize the distribution of captured reflectance spectra revealing small-scale spatial variability of water composition. Next, we demonstrate how the nodes of the fitted GTM can be interpreted as unique spectral endmembers. Using extracted endmembers together with the normalized spectral similarity score, we are able to efficiently map the abundance of near shore algae as well as the evolution of a rhodamine tracer dye used to simulate water contamination by a localized source.

The unprecedented progress in Artificial Intelligence (AI), particularly in deep learning algorithms with ubiquitous internet connected smart devices, has created a high demand for AI computing on the edge devices. This review studied commercially available edge processors, and the processors that are still in industrial research stages. We categorized state-of-the-art edge processors based on the underlying architecture, such as dataflow, neuromorphic, and Processing in-Memory (PIM) architecture. The processors are analyzed based on their performance, chip area, energy efficiency, and application domains. The supported programming frameworks, model compression, data precision, and the CMOS fabrication process technology are discussed. Currently, most of the commercial edge processors utilize dataflow architectures. However, emerging non-von Neumann computing architectures have attracted the industry in recent years. Neuromorphic processors are highly efficient for performing computation with fewer synaptic operations, and several neuromorphic processors offer online training for secured and personalized AI applications. This review found that the PIM processors show significant energy efficiency and consume less power compared to dataflow and neuromorphic processors. The future direction of the industry would be to implement state-of-the-art deep learning algorithms in emerging non-Von Neumann computing paradigms for low power computing on the edge devices.

The European Green Deal poses a two-pronged challenge for the automotive industry: migrating to solutions based in light structures, requiring light weight concepts and light materials, while at the same time avoiding dependence towards the importation of these advanced materials. Aluminium alloys are lightweight and cost-effective materials that can successfully cover the requirements of many structural applications, however their production requires from bauxite and other Critical Raw Materials (CRM), such as Si and Mg. Aluminium alloys are fully recyclable, but scrap is usually contaminated and its use is related to an increment of impurities, tramp element and undesired inclusions. Traditionally, the use of secondary alloys has been restricted to low performance applications. The present work analyses the effect that the use of scrap has in the quantity of inclusions present in the alloy and in other properties relevant for the material processing. The study was carried out for common alloys belonging to 3 of the most common aluminium processes used in the car manufacturing industry: High Pressure Die Casting (HPDC) (EN AC-43500), extrusion (6063) and sheet metal forming (5754 and 6181). Reference alloy were mixed with different level of scrap (0, 20, 40, 60, 80 and 100%) trying to keep the chemical composition as unaffected as possible. The inclusions level of the alloy was characterized with the Prefil Foot-printer® test. In addition, the obtained materials, after being cast in an open mould, were subjected to metallographic characterization. Relevant properties to assess the formability quality of the alloys for the corresponding transforming process, were obtained: flowability test for HPDC alloy and high temperature compression for extrusion alloys. The results obtained suggest that the number of inclusions present in the melt highly increase with the amount of scrap used to produce the alloy. These inclusions are also related with an important lost of flowability, but do not have a noticeable impact on microstructure.

In this study, it was analyzed that the characteristics of ammonia and their effects on secondary particulate matter (PM) formation by region in Korea during 2020. The NH3 concentration was high in GJ (11.4 ppb) neighboring agricultural area followed by DJ (9.0 ppb) and SE (8.6 ppb) locating in the urban area. On the other hand, BI (2.6 ppb) and JI (4.5 ppb), which are background regions, were lower than other area. Seasonally, ammonia was high in spring and summer, and it generally increased when human activities are active. Therefore, it is believed that ammonia in the atmosphere changes depending on not only local emissions but also temperature-dependent phase distribution characteristics. For SE and GJ, regions with relatively high ammonia concentrations, the effect of ammonia on secondary PM formation was conducted. In both regions, the ammonium-to-sulfate mole ratio tended to increase with an ammonia or PM2.5 concentration increasing. It can be assumed that PM2.5 concentration increases as nitrates are formed under the ammonia sufficient condition. The adjusted gas ratio is generally greater than 4, indicating that there is a lot of free ammonia. Thus, it is estimated that reduction of ammonia would not effective to restrain the nitrate formation.

We study L_2-approximation problems in the weighted Hilbert spaces in the worst case setting. Three interesting weighted Hilbert spaces appear in this paper, whose weights are equipped with two positive parameters $\ga_j$ and $\az_j$ for $j=1,\,2,\dots,\,d$. We consider the worst case error of algorithms that use finitely many arbitrary continuous linear functionals. We discuss the exponential convergence-(t,s)-weak tractability (EC-(t,s)-WT) of these L_2-approximation problems under the absolute or normalized error criterion. In particular, we obtain the sufficient and necessary conditions for EC-(1,1)-WT and EC-(t,1)-WT with t

The successful 2020 launch and 2021 landing of the National Aeronautics and Space Administration’s (NASA) Perseverance Mars rover initiated the first phase of the NASA and European Space Agency (ESA) Mars Sample Return (MSR) campaign. The goal of the MSR campaign is to collect scientifically interesting samples from the Martian surface and return them to Earth for further study in terrestrial laboratories. The MSR campaign consists of three major spacecraft components to accomplish this objective: the Perseverance Mars rover, the Sample Retrieval Lander (SRL) and the Earth Return Orbiter (ERO). Onboard the ERO spacecraft is the Capture, Containment and Return System (CCRS). CCRS will capture, process and return to Earth the samples that have been collected after they are launched into Mars orbit by the Mars Ascent Vehicle (MAV), which is delivered to Mars onboard the SRL. To facilitate the processing of the orbiting sample (OS) by CCRS we have designed and developed a vision system to determine the OS capture orientation. The vision system is comprised of two cameras sensitive to the visible portion of the electromagnetic spectrum and two illumination modules constructed from broadband light emitting diodes (LED). Vision system laboratory tests and physics-based optical simulations predict CCRS ground processing will be able to correctly identify the OS post-capture orientation using only a single vision system image that is transmitted to Earth from Mars orbit.

The microbial communities are closely related to the overall health and quality of soil, but studies on microbial ecology in apple-pear orchard soils are limited. In the current study, 28 soil samples were collected from three apple-pear orchards in northeastern China, and the composition and structure of fungal and bacterial communities were investigated by high-throughput sequencing. Molecular ecological network showed that the keystone taxa of bacterial communities were Actinobacteria, Proteobacteria, Gemmatimonadetes, Acidobacteria, Nitrospirae, and Chloroflexi, and the keystone taxa of fungal communities was Ascomycota. Mantel tests showed that soil texture and pH were important factors shaping soil bacterial and fungal communities, and soil water soluble organic carbon (WSOC) and nitrate nitrogen (NO3--N) were also closely related to soil bacterial communities. Canonical correspondence analysis (CCA) and variation partition analysis (VPA) analysis revealed that geographic distance, soil texture, pH, and other soil properties could explain 10.55%, 13.5%, and 19.03% of the overall variation of bacterial communities, and they explained 11.61%, 13.03%, and 20.26% of the overall variation of fungal communities, respectively. The key stone taxa of bacterial and fungal communities in apple-pear orchard soils and their strong correlation with soil properties could provide useful clues toward sustainable management of orchards.

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

(1) Background: Multiple alterations of cellular metabolism have been documented in experimental studies of autosomal dominant polycystic kidney disease (ADPKD) and are thought to contribute to its pathogenesis. (2) Methods: To elucidate the molecular pathways and transcriptional regulators associated with the metabolic changes of renal cysts in ADPKD, we compared global gene expression data from human PKD1 renal cysts, minimally cystic tissues (MCT) from the same patients, and healthy human kidney cortical tissue samples. (3) Results: We found PKD1 renal cysts displayed the Warburg effect with gene pathway changes favoring increased cellular glucose uptake and lactate production, instead of pyruvate oxidation. Additionally, mitochondrial energy metabolism was globally depressed, associated with downregulation of gene pathways related to fatty acid oxidation (FAO), branched-chain amino acid (BCAA) degradation, the Krebs cycle, and oxidative phosphorylation (OXPHOS) in renal cysts. Activation of mTORC1 and its two target proto-oncogenes, HIF-1α and MYC, was predicted to drive the expression of multiple genes involved in the observed metabolic reprogramming (e.g., GLUT3, HK1/HK2, ALDOA, ENO2, PKM, LDHA/LDHB, MCT4, PDHA1, PDK1/3, MPC1/2, CPT2, BCAT1, NAMPT); indeed, their predicted expression patterns were confirmed by our data. Conversely, we found AMPK inhibition was predicted in renal cysts. AMPK inhibition was associated with decreased expression of PGC-1α, a transcriptional coactivator for transcription factors PPARα, ERRα, and ERRγ, all of which play a critical role in regulating oxidative metabolism and mitochondrial biogenesis. (4) Conclusions: These data provide a comprehensive map of metabolic pathway reprogramming in ADPKD and highlight nodes of regulation that may serve as targets for therapeutic intervention.

The ground surface deformation induced by shield tunnels passing through enclosure structure of existing tunnels is a particular underground construction scenario, which is encountered in Wuhan metro line 12 engineering cases in China. The classic ground deformation theory is difficult to accurately predict this ground deformation. This paper develops a semi-analytical method to predict ground heave considering space effect in this engineering condition. Based on improved ground deformation theory, a novel deformation prediction method of ground and enclosure structure is derived combined with Kirchhoff plate theory. Comparing with field deformation measurements, the maximum difference between measured and calculated deformation is 14.6%, which demonstrating that the proposed method can be used to predict the ground heave induced by shield tunnels passing through the enclosure structure of existing tunnels. The parameters of underground diaphragm wall used in Wuhan metro line 12 are further studied in detail. The results show that the ground heaves have positive correlation with embedded ratio of diaphragm wall, but negative correlation with its elastic modulus and thickness. But the thickness and embedded ratio has a limited effect on ground heaves. This study provides a technical reference for optimization setting of enclosure structure in protecting existing building.

This work presents emission line flux and kinematic structure mapping based on IFU data of the planetary nebulae Abell 30 (A30). The IFU has a field of view (FoV) of 16" x 12.3" and was used to partially cover knots J1 and J2, and completely cover knots J3 and J4 of A30. Our emission line flux map shows recombination species C II, C III, He I, O II as well as forbidden line species [O III], [Ne III] and [Ne IV] of high excitation level are all distributed in different parts of the knots. The kinematic structure shows considerable variation in both the velocities and spatial locations of these knots with positive and negative velocity excursions from the systematic value. Forbidden line species [O III], [Ne III] are distributed in both knots J3 and J4 but they are travelling at different speeds in opposite directions. Despite variation in distribution of the species, the velocities of [Ne IV] and [O III] are similar and travelling in the same direction while the other species [Ne III], He I, and O II share similar velocity of 200kms−1 up in the opposite direction. The complexity of distribution and kinematic structure of the knots revealed in this work indicates a strong tendency towards the hypothesis of multiple triggering events in the past history of A30.

This study explores fault-tolerant consensus in leader-following heterogeneous multi-agent systems, focusing on actuator failures in uncrewed aerial vehicles (UAVs) and uncrewed ground vehicles (UGVs). An optimization-based fault-tolerant consensus algorithm is proposed. The algorithm utilizes the Euler-Lagrange formula to ensure system consistency under actuator failures, with the Lyapunov stability theory proving the asymptotic stability of the consistency error. The algorithm is applied to heterogeneous multi-agent systems of UAVs and UGVs to derive optimal fault-tolerant consensus control laws for each vehicle type. Simulation experiments give evidence for the feasibility of the proposed control strategy.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of a SPS device used for material processing and synthesis both in both scientific and industrial applications. This work presents an example of processing Arc-Meleted (half-Heusler, cobalt triantimonide) and SHS-synthesized semiconductors (bismuth telluride) materials with SPS device. The system functionalities expansion is presented, showing the possible way of increasing the information amount obtained about SPS processes and using the SPS apparatus for conducting synthesis of materials and increasing reproducibility and accuracy of process parameters control.

We introduce the Symplectic Structure of Information Geometry based on Souriau’s Lie Group Thermodynamics model, with a covariant definition of Gibbs equilibrium via invariances through co-adjoint action of a group on its moment space, defining physical observables like energy, heat, and moment as pure geometrical objects. Using Geometric (Planck) Temperature of Souriau model and Symplectic cocycle notion, the Fisher metric is identified as a Souriau Geometric Heat Capacity. Souriau model is based on affine representation of Lie Group and Lie algebra that we compare with Koszul works on G/K homogeneous space and bijective correspondence between the set of G-invariant flat connections on G/K and the set of affine representations of the Lie algebra of G. In the framework of Lie Group Thermodynamics, an Euler-Poincaré equation is elaborated with respect to thermodynamic variables, and a new variational principal for thermodynamics is built through an invariant Poincaré-Cartan-Souriau integral. The Souriau-Fisher metric is linked to KKS (Kostant-Kirillov-Souriau) 2-form that associates a canonical homogeneous symplectic manifold to the co-adjoint orbits. We apply this model in the framework of Information Geometry for the action of an affine Group for exponentiel families, and provide some illustrations of use cases for multivariate Gaussian densities. Information Geometry is presented in the context of seminal work of Fréchet and his Clairaut-Legendre equation. Souriau model of Statistical Physics is validated as compatible with Balian gauge model of thermodynamics. We recall the precursor work of Casalis on affine group invariance for natural exponential families.

Due to its potential harm to space payload, microwave corona breakdown of microstrip circuits has attracted much attention. This work describes an efficient way to suppress corona breakdown. Since corona breakdown threshold is determined by the highest electric field intensity at the surface of microstrip circuits, lacquer coating with thickness of tens of microns is sprayed on the top of microstrip circuits. The applied dielectric coating is used to move the discharge location away from circuit’s surface which is equivalent to reduce the highest electric field intensity on the in-terface of solid/air of the circuit and thus results into higher breakdown threshold. Two designs of classic coupled-line band-pass filter were used for verification. Corona experimental results at 2.5 GHz show that, in the interested low pressure range (100 to 4500 Pa), 5.3 dB improvement of mi-crowave corona breakdown threshold can be achieved for a filter with narrowest gap of 0.2 mm while its electrical performances like insertion loss, Q-factor are still acceptable. A threshold improvement prediction method is also presented and validated.

In orthopedics, bone drilling is a crucial part of a surgical method commonly carried out for internal fixation in bone fracture treatment. The primary purpose of bone drilling is the creation of holes for screw insertion to immobilize fractured parts. The bone drilling task depends on the orthopedist and surgeon’s high level of skill and experience. This paper aimed to provide a summary of previously published review studies in the field of bone drilling. This review paper also presents a comprehensive review of the application of machine learning for bone drilling and as a future direction for the automation system. This review can also help medical surgeons and bone drillers understand the latest improvements through parameter selection and optimization strategies to reduce bone damage in bone drilling procedures. Apart from the review study, bone drilling vibration data collected in the University laboratory experiment is also presented in this study. The vibration data consist of three different layers of femur cow bone which are processed and classified using several machine learning methods. LSTM is, used in the bone drilling classification study to prove that the layers of the bone drilling are associated with the vibration signal and can be classified and predicted using the machine learning method.

Relativistic shocks are one of the most plausible sites of the emission of strongly variable, polarized multi-wavelength emission from relativistic jet sources such as blazars, via diffusive shock acceleration (DSA) of relativistic particles. This paper summarizes recent results on a self-consistent coupling of diffusive shock acceleration and radiation transfer in blazar jets. We demonstrate that the observed spectral energy distributions (SEDs) of blazars strongly constrain the nature of hydromagnetic turbulence responsible for pitch-angle scattering by requiring a strongly energy-dependent pitch-angle mean free path. The prominent soft X-ray excess (``Big Blue Bump'') in the SED of the BL Lac object AO 0235+164 can be modelled as the signature of bulk Compton scattering of external radiation fields by the thermal electron population, which places additional constraints on the level of hydromagnetic turbulence. It has further been demonstrated that internal shocks propagating in a jet pervaded by a helical magnetic field naturally produce polarization-angle swings by 180$^o$, in tandem with multi-wavelength flaring activity, without requiring any helical motion paths or other asymmetric jet structures. The specific application of this model to 3C279 presents the first consistent, simultaneous modeling of snap-shot SEDs, multi-wavelength light curves and time-dependent polarization signatures of a blazar during a polarization-angle (PA) rotation. This model has recently been generalized to a lepto-hadronic model, in which the high-energy emission is dominated by proton synchrotron radiation. It is shown that in this case, the high-energy (X-ray and $\gamma$-ray) polarization signatures are expected to be significantly more stable (not showing PA rotations) than the low-energy (electron-synchrotron) signatures.

A new generalized definition of Mersenne numbers is proposed of the form (a^n - (a-1)^n), called Global Generalized Mersenne numbers, or simply Generalized Mersenne numbers and noted GM_{a,n} where a is the base and n is the exponent, both being positive integers. The properties are investigated for prime exponents n and several theorems on Mersenne numbers regarding their congruence properties are generalized and demonstrated. In particular, it is found that, for any base a, Generalized Mersenne numbers are in general such that (GM_{a,n} - 1) are even and divisible by n, a and (a-1) for any odd prime exponent n and by (a(a-1)+1) for any prime exponent n > 5. The remaining factor is a function of triangular numbers of (a-1), specific to each prime exponent n. Four theorems on Mersenne numbers are generalized and four new theorems are demonstrated, allowing to show first, that (GM_{a,n} - 1) are divisible by 6, and more precisely GM_{a,n} are congruent to 1(mod 12) or 7(mod 12) depending on the congruence of the base a(mod 4); second, that (GM_{a,n} - 1) are divisible by 10 if n == 1(mod 4) and, if n == 3(mod 4), GM_{a,n} == 1(mod 10), or 7(mod 10) or 9(mod 10) depending on the congruence of the base a(mod 5); third, that all factors c_{i} of GM_{a,n} are of the form (2nf_{i}+1) with f_{i} natural integers such that c_{i} is prime itself or the product of primes of the form (2nj+1) with j natural integer; fourth, that for odd prime exponents n, all GM_{a,n} are periodically congruent to either +/-1\(mod 8) or +/-3(mod 8) depending on the congruence of the base a(mod 8); and fifth, that the factors of a composite GM_{a,n} is of the form (2nf_{i}+1) with f_{i} == u(mod 4) and u being either 0, 1, 2 or 3 depending on the congruence of the exponent n(mod 4) and on the congruence of the base a(mod 8). The potential use of Generalized Mersenne primes in cryptography is shortly addressed.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

Rapid climate change requires more powerful and precise modeling methods to forecast future climate variability. The GSTARIMA Model is efficient, combining space-time analysis with the Autoregressive Moving Average (ARIMA) Model. The integration of heteroscedasticity error and the Kriging method can strengthen the Model's ability to handle the problem of non-constant error variance in the GSTARIMA Model and forecast at unobserved locations of climate observations. This paper's Systematics Literature Review (SLR) is presented comprehensively with the principal aim of developing a thorough understanding of applying the GSTARIMA Model with heteroskedasticity error and the Kriging Method in climate forecasting following the Data Analytics Lifecycle methodology. The Systematic Literature Review (SLR) process consists of three main stages. We sourced the articles from databases such as Scopus, Dimensions, and EBSCO-Host The subsequent stage involved conducting a comprehensive literature review using the PRISMA method to ensure rigor and depth. Additionally, we performed bibliometric analysis to enhance rigor. Lastly, we conducted a gap analysis session to scrutinize existing research on the GSTARIMA Model and identify new opportunities. This literature review reveals that integrating GSTARIMA Model with heteroscedasticity errors and the Kriging method is suitable for climate forecasting. This research inspires researchers to contribute to the improvement and refinement of the Model, making it a more potent and valuable tool in climate forecasting.

Drones have experienced rapid technological advancements, leading to the proliferation of small, low-cost, remotely controlled, and autonomous aerial vehicles with diverse applications, from package delivery to personal transportation. However, integrating these drones into the existing air traffic management (ATM) system poses significant challenges. The current ATM infrastructure, designed primarily for traditional manned aircraft, requires enhanced capacity, workforce, and cost-effectiveness to coordinate the large numbers of drones expected to operate at low altitudes in complex urban environments. To address this critical issue, this study aims to develop an intelligent, highly automated drone management system for integration into smart city transportation networks. The key objectives include: i) Developing a conceptual framework for an intelligent total transportation management system tailored for future smart cities, focusing on incorporating drone operations; ii) Designing an advanced air traffic management and flight control system capable of managing individual drones and drone swarms in complex urban environments; iii) Improving drone management methods by leveraging drone-following models and emerging technologies such as the Internet of Things (IoT) and the Internet of Drones (IoD); and iv) Investigating the landing processes and protocols for unmanned aerial vehicles (UAVs) to enable safe and efficient operations.

With the rapid growth of large language models (LLMs), there is increasing demand for memory and computation in LLMs. Recent efforts on post-training pruning of LLMs aim to reduce the model size and computation requirements, yet the performance is still sub-optimal. In this paper, we present a plug-and-play solution for post-training pruning of LLMs. The proposed solution has two innovative components: 1) Relative Importance and Activations (RIA), a new pruning metric that jointly considers the weight and activations efficiently on LLMs; and 2) Channel Permutation, a new approach to maximally preserve important weights under N:M sparsity. The two proposed components can be readily combined to further enhance the N:M semi-structured pruning of LLMs. Our empirical experiments show that RIA alone can already surpass all existing post-training pruning methods on prevalent LLMs, e.g., LLaMA ranging from 7B to 65B. Furthermore, N:M semi-structured pruning with channel permutation can even outperform the original LLaMA2-70B on zero-shot tasks, together with practical speed-up on specific hardware. Our code is available at: https://github.com/biomedical-cybernetics/Relative-importance-and-activation-pruning

The Automatic Dependent Surveillance-Broadcast (ADS-B) protocol stands as a cornerstone in modern aviation surveillance and Aircraft Traffic Control systems, integral to the NextGen project initiated by the US Department of Federal Aviation Administration (FAA) in 2005. ADS-B utilizes data links to autonomously broadcast Aircraft navigational and identification information to augment air transportation system capacity and safety. However, concerns regarding the protocol's security persist, particularly as its adoption expands. The unencrypted nature of transmitted aircraft data and the absence of robust authentication mechanisms render the protocol susceptible to exploitation by malicious actors. In this study, we comprehensively reviewed existing research in the field, identifying a crucial gap necessitating a holistic survey. Prior surveys have predominantly focused on specific aspects, such as vulnerabilities, attacks, or critiques of existing solutions. Our survey addresses this gap by thoroughly exploring the aviation system, providing readers with a nuanced understanding of ADS-B security. Utilizing a detailed SWOT analysis diagram, our paper delves into the vulnerabilities inherent in the ADS-B protocol outlines potential threats and scrutinizes various attack scenarios. We systematically categorize and analyze existing security solutions, considering cost-effectiveness, scalability, implementation complexity, and coverage against diverse attack vectors. Furthermore, we critically evaluate these solutions, elucidate ADS-B security requirements, discuss current challenges, and propose future research directions. This survey serves as a comprehensive resource for researchers and practitioners alike, shedding light on the multifaceted landscape of ADS-B security and paving the way for enhanced aviation system resilience in the face of evolving cybersecurity threats.

The Azores Archipelago is a collection of volcanic islands near northwestern Portugal in the Atlantic Ocean. Because of the importance of accurate environmental monitoring for the advancement of research, transportation and tourism, a LoRaWan Sensor Network was developed to monitor levels of air pollution across these islands. This study presents an approach to the implementation of a blockchain network that is both lightweight and scalable, with the goal of preventing man-in-the-middle attacks on the design of sensor networks.

Floods, recognized for their erratic behavior and devastating effects, are a significant threat as a natural disaster. In Brunei Darussalam, the impact of climate change is becoming increasingly evident through higher temperatures and an expected increase in annual rainfall (5.0mm per year from 2021 to 2050), highlighting the critical need for updated flood risk management techniques. In line with the climate resilience and adaptation objectives of WAWASAN 2035, this paper introduces an innovative approach—a cutting-edge flood risk management framework that utilizes the capabilities of big data analytics, sophisticated machine learning algorithms, and smart Internet of Things (IoT) sensors. Traditional methods, which rely on numerical and physical data modeling, often do not provide precise short-term flood forecasts. Our suggested framework uses machine learning to analyze real-time flood forecasting, sensor data and enhance warning systems, addressing the shortcomings of traditional approaches. The key advantage of this approach is its potential to drastically decrease flood-related damages, protect lives, and boost infrastructure resilience. This proposal is not only in aligns with Brunei's vision for a safe and climate-adaptable future but also marks a significant step forward in adopting innovative and sustainable flood risk management solutions amidst an evolving climate.

Network Function Virtualization (NFV) allows for the dynamic provisioning of Virtualized Network Functions, adapting services to the complex and real-time network environment for enhanced network performance. Despite the benefits of NFV, virtual network functions (VNFs) migration and the energy consumption pose significant challenges due to the dynamic nature of the physical network, especially in the edge-cloud continuum network. Currently, people tackle this challenge by predicting the network traffic and then proactively migrating the VNFs using the predicted values. There are two challenges here. First, when SFCs belong to different network service providers, the historical network traffic data is held by the service providers, and they are reluctant to share the historical data due to privacy concerns. Without the historical network traffic data of each SFC, the resource provider that owns the underlying network cannot effectively predict the network traffic; in addition, without the feedback of the migration results of the underlying physical network, the network traffic prediction will be difficult to match the needs of the physical network. In this manuscript, we solve the problem of network traffic prediction in the NFV-based edge-cloud continuum network for multiple network service providers. We aim to improve migration performance and reduce energy consumption while ensuring resource and latency requirements. To protect the privacy of each network service provider, we apply an FL algorithm. After that, to improve the migration performance, we tailor the loss function. In the loss function, factors such as the number of migrations, the number of migration failures, and the energy consumption of the NFV-based edge-cloud continuum network are added. Additionally, to obtain the results of the SFC migration, we develop a mathematical model for the problem of multiple network service providers in the NFV-based network. The effectiveness of our algorithm is evaluated through extensive simulations, and the results show a significant reduction in the number of migrated nodes and energy consumption while improving the SFC acceptance ratio compared to state-of-the-art schemes which only use the difference between predicted and actual flows to define the loss function.

Breast cancer (BC) is a prevalent malignancy with various subtypes, each presenting unique diagnostic and therapeutic challenges. Triple-negative breast cancer (TNBC), which comprises 12-17% of breast cancers, is particularly aggressive due to its lack of estrogen receptor (ER), progesterone receptor (PR), and HER2 expression. This case report details the management of a 64-year-old woman with TNBC. Initially presenting with a left breast nodule, she underwent a biopsy that confirmed triple-negative infiltrating ductal carcinoma. Despite negative BRCA genetic testing, her significant family history of cancer and a newly detected right breast lesion led to a bilateral mastectomy. Post-surgery imaging revealed multiple hypodense nodules and a spiculated pulmonary nodule, prompting further investigation. An endoscopic lung biopsy identified a primary pulmonary carcinoma with histological features similar to the breast cancer, indicating the lung as the primary source. This case underscores the complexity of TNBC, the importance of comprehensive diagnostic evaluations, and the need for considering extramammary origins in metastatic cases. The findings emphasize the role of multidisciplinary teams in managing such rare and challenging cases and highlight the necessity for thorough and repeated evaluations in atypical BC presentations.

The digital model of airborne frequency selective surface radomes (AFSSRs) is the basis of design, simulation analysis, manufacturing, and other related research of AFSSRs. This paper proposes a rapid modeling method of AFSSRs based on dynamic customizable primitives. Firstly, a layered digital model construction scheme of AFSSR is presented based on the typical radome wall structure. Then, according to the characteristics of various surface configurations and complex wireframe information of AFSSRs, the dynamic primitives are raised to express the boundary and contour information of all kinds of radomes. Focusing on the undevelopable characteristics of the aero-dynamic shape surface of the AFSSR, the arrangement solution and mapping method for frequency selective elements on undevelopable surfaces are proposed. Furthermore, the imple-mentation logic of this method on the creation of each layer model and the assembly of the whole machine model is introduced. Finally, according to this method, a rapid modeling system (RMS) is established, and the modeling effect and efficiency of the RMS are demonstrated and compared, which verifies the feasibility and effectiveness of this method.

The comparison of three types of ionosonde data from Europe during an Interplanetary Coronal Mass Ejection (ICME) and a Stream Interaction Regions (SIRs) / Corotating Interaction Regions (CIRs) -driven geomagnetic storm event is detailed in this study. The selected events are 16-20 March 2015 for the ICME-driven and 30 May to 04 June 2013 for the SIR/CIR-driven one. Ionospheric data from three European ionosonde stations, namely Pruhonice (PQ), Sopron (SO) and Rome (RO), are investigated. The ionospheric F2-layer responses to these geomagnetic events are analyzed with the ionospheric foF2 and h’F2 parameter, the calculated deltafoF2 and deltahF2 values, ratio of Total Electron Content (rTEC) and Thermosphere, Ionosphere, Mesosphere, Energetics and Dynamics (TIMED) satellite Global Ultraviolet Imager (GUVI) thermospheric [O]/[N2] measurement data. The storm-time and the quiet day mean values are also compared, and it can be concluded that the quiet day curves are similar at all stations while the storm-time ones showed the latitudinal dependence during the development of the storm. As a result of the electron density comparison, during the two events it can be concluded that SSC that characterized the ICME induced a Travelling Atmospheric Disturbance (TAD) seen in the European stations, while this is not in the SIR/CIR-driven ionospheric storm, which showed a stronger and more prolonged negative effect in all stations probably due to the season.

This brief essay explores both the social and biological dimensions of human sexuality in light of the possibility of a substantial commerce in sexually-enabled robots, and concludes with some potentially strategic considerations for those who find themselves involved with their design, production, and/or marketing.

Background and Objectives: Knee osteoarthritis (KOA) is a degenerative disease that is targeting continuously people of different ages, but especially the elderly population, the number of which tends to increase continuously at the global level. Apart from age, excess weight can influence the evolution of the disease, with obesity being associated with a weak inflammation stage, and an imbalance between pro-inflammatory and anti-inflammatory cytokines. The present work aimed to identify specific biomarkers alike ACRP-30, IL-10, TNF-α, and IL-6 in synovial fluid and correlate them with patients’ clinical data. Materials and Methods: 24 subjects with KOA and over 50 years of age are involved in the present study. All patients performed a supine X-ray at the target knee. Ultrasound was performed using an ESAOTE MyLab Omega (ESAOTE Spa, Italy) ultrasound device and a 6-19 MHz linear array transducer. Results: The obtained results highlighted a significant correlation between age and adiponectin level (p=0.0451, r=-0.412). Also, the IL-10 values are lower in cases where the intensity of the pain is more pronounced (p=0.0405, r=-0.421). In addition, analyzing the data by gender, it was observed that in the case of males, stiffness is more related to age (p=0.0079, r=0.7993), compared to women (p=0.0203, r=0.6223). In the case of women, the progression of the disease tends to increase more intensively total WOMAC score’s values (p=0.00031, r=0.8342), compared with men (p=0.0289, r=7013). Regarding interleukins and BMI, significant correlations were observed only in the case of men. Conclusions: A significant correlation between age and adiponectin, and adiponectin and IL-6, suggests that advanced age may contribute to adiponectin reduction. Comparing men with women, it was observed that men's age is more related to rigidity, and IL-6 and IL-10 are directly correlated to BMI and women seem to be more sensitive to pain and stiffness.

The effective integration of aerial remote sensing data and ground multi-source data has always been one of the difficulties of quantitative remote sensing. A new monitoring mode is designed which installs the hyperspectral imager on the UAV and places a buoy spectrometer on the river. Water samples are collected simultaneously to obtain in situ assay data of total phosphorus, total nitrogen, COD, turbidity and chlorophyll during data collection. The cross correlogram spectral matching (CCSM) algorithm is used to match the data of the buoy spectrometer with the UAV spectral data to reduce the UAV data noise significantly. An absorption characteristics recognition algorithm (ACR) is designed to realize a new method for comparing UAV data with laboratory data. This method takes into account the spectral characteristics and the correlation characteristics of test data synchronously. It is concluded that the most accurate water quality parameters can be calculated by using the regression method under five scales after the regression tests of multiple linear regression method (MLR), support vector machine method (SVM) and neural network (NN) method. This new working mode of integrating spectral imager data with point spectrometer data will become a trend in water quality monitoring.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

An innovative wireless sensor network (WSN) based on Ultra-Wide Band (UWB) technology for 3D accurate superficial monitoring of ground deformations, as landslides and subsidence, is proposed. The system has been designed and developed as part of an European Life+ project, called Wi-GIM (Wireless Sensor Network for Ground Instability Monitoring). The details of the architecture, the localization via wireless technology and data processing protocols are described. The flexibility and accuracy achieved by the UWB two-way ranging technique is analysed and compared with the traditional systems, such as robotic total stations (RTSs), Ground-based Interferometric Synthetic Aperture Radar (GB-InSAR), highlighting the pros and cons of the UWB solution to detect the surface movements. An extensive field trial campaign allows the validation of the system and the analysis of its sensitivity to different factors (e.g., sensor nodes inter-visibility, effects of the temperature, etc.). The Wi-GIM system represents a promising solution for landslide monitoring and it can be adopted in conjunction with traditional systems or as an alternative in areas where the available resources are inadequate. The versatility, easy/fast deployment and cost-effectiveness, together with the good accuracy, make the Wi-GIM system a possible solution for municipalities that cannot afford expensive/complex systems to monitor potential landslides in their territory.

This study analyses regional development in one of the poorest provinces in China, Guizhou Province, between 2000 and 2012 using a multiscale and multi-mechanism framework. In general, regional inequality has been declining since 2000. In addition, economic development in Guizhou Province presented spatial agglomeration and club convergence, which shows how the development pattern of one core area, two-wing areas and a contiguous area at the edge of the province have been developed between 2006 and 2012. Multilevel regression analysis revealed that industrialization and investment level were the primary driving forces of regional economic disparity in Guizhou Province. The influences of marketization and decentralization on regional economic disparity were relatively weak. Investment level reinforced regional economic disparity and the development of core-periphery structure in the province. However, investment level actually weakened the regional economic disparity in Guizhou Province when the variable of time was considered. In addition, both the topography and urban–rural differentiation were the two main reasons for forming a core-periphery structure in Guizhou Province.

Logistics Engineering has transcended over the decades into an approach for competitive benefits in organisational performance and logistics efficiency. Most industries are recognising that significant savings are available to companies that are able to ordinate and improve within their logistics operations. Companies today face great challenges because the successful supply of many products and services needs to the effective integration of logistics activities across a prolongation supply chain and an increasing geographical separation. Moreover, logistics integration approach involves both internal integration for an ordinated, unified process as well as relationships to react flexibly, changeability, and responsibility to customer's demands. In this study, by using of Fuzzy Vikor (F-Vikor), the best combination of RIR was selected and RIR Locating was done. The main aim of this paper is survey and design of the integrated operational logistics network (IOLN) and also, a proposed IOLN to integration of the Iran Khodro Co Supply Network.

In this paper, a two-stage stochastic programming modelling is proposed to design a multi-period, multistage, and single-commodity integrated forward/reverse logistics network design problem under uncertainty. The problem involves both strategic and tactical decision levels. The first stage deals with strategic decisions, which are the number, capacity, and location of forward and reverse facilities. At the second stage tactical decisions such as base stock level as an inventory policy is determined. The generic introduced model consists of suppliers, manufactures, and distribution centers in forward logistic and collection centers, remanufactures, redistribution, and disposal centers in reverse logistic. The strength of proposed model is its applicability to various industries. The problem is formulated as a mixed-integer linear programming model and is solved by using Benders’ Decomposition (BD) approach. In order to accelerate the Benders’ decomposition, a number of valid inequalities are added to the master problem. The proposed accelerated BD is evaluated through small-, medium-, and large-sized test problems. Numerical results reveal that proposed solution algorithm increases convergence of lower bound and upper bound of BD and is able to reach an acceptable optimality gap in a convenient CPU time.

The use of didactic and interactive materials is essential in generating interest among students and teachers in utilizing mathematical models and digital technologies for the educational process. These materials create a dynamic and engaging learning environment that promotes a deeper understanding of complex concepts and fosters a passion for learning. Additionally, integrating interactive materials into pilot courses can assist teachers in better assessing student learning and adjusting the teaching strategies accordingly and the teachers can receive valuable insights into students' strengths and weaknesses, allowing them to provide targeted support and intervention when needed. In this context, the purpose of this paper is to introduce an approach for solving mathematics problems embedded in technical scenarios within the defense and security fields with the aid of digital technology. In this way, students can visualize abstract concepts, experiment with different scenarios, and receive instant feedback on their understanding. This paper helps to reinforce key concepts and enhance problem-solving skills, sparking curiosity, creativity, and encouraging active participation and collaboration. Throughout the development of this proposal, good practices are adopted, and advice for improvement is collected while having a wide range of users, giving feedback, discussions, and testing (pilot) short-term learning/teaching/training activities.

Integrated assessment modelling (IAM) has been successfully used in the development of international agreements to reduce transboundary pollution in Europe, based on the GAINS model of IIASA. At a national level in the UK a similar approach has been taken with the UK Integrated Assessment Model, UKIAM, superimposing pollution abatement measures and behavioural change on energy projections designed to meet targets set for reduction of greenhouse gas emissions, and allowing for natural and imported contributions from other countries and shipping. This paper describes how UKIAM has been used in development of proposed targets for reduction of fine particulate PM2.5 in the Environment Act, exploring scenarios encompassing different levels of ambition up to 2050 with associated health and other environmental benefits. There are two PM2.5 targets, an annual mean concentration target setting a maximum concentration to be reached by a future year, and a population exposure reduction target with benefits for health across the whole population. The work goes further, to also demonstrate links to social deprivation. There is a strong connection between climate measures aimed at reducing net GHG emissions to zero by 2050 and future air quality, which may be positive or negative, as illustrated by sectoral studies for road transport where electrification of the fleet needs to match the evolution of energy production, and for domestic heating where use of wood for heating is an air quality issue. UKIAM has been validated against air pollution measurements and other modelling, but there are many uncertainties including future energy projections. New work is beginning to link UKIAM directly with the TIMES model addressing future energy projections, to explore different uptake scenarios for hydrogen production and use with respect to air quality.

A new algorithm is developed in this study to automatically detect reinforced concrete structures' rebar locations and diameters using the ground penetrating radar technique. The method approximates the hyperbolic signatures using two-way travel time and bi-quadratic equations. The study includes formulating electromagnetic wave speed in reinforced concrete (RC) structures. The algorithm was used in a computer code to provide an automated analysis of ground-penetrating radar data collected from a pre-planned survey grid. Two RC slabs were fabricated and tested to validate the proposed method. The proposed method is efficient in signal processing and accurately and reliably determining the rebar information.

Hyperspectral imaging, a rapidly evolving technique, furnishes exhaustive information on Earth's surface reflectance over an extensive spectrum of wavelengths. We have developed a more precise method for analyzing spectral data by meticulously selecting plant leaf pixels and employing a relative reference approach. This enhanced technique correlates camera pixel values with light intensity, bypassing the need for complex equations and thereby providing clearer insights into vegetation vitality. The findings of this study not only enhance the precision of hyperspectral imaging but also bolster our capability for ecological monitoring and understanding environmental health. A novel algorithm based on the red-edge slope was established to classify images, exploiting the spectral reflectance data gleaned from the hyperspectral Liquid Crystal Tunable Filter (LCTF) camera. Compared with conventional SVM and K-means algorithms, our novel algorithm demonstrated commendable performance, achieving an overall accuracy of 90% with a Kappa Coefficient of 0.86. This comparison highlights the novel algorithm's relative strength and potential for large-scale satellite and drone imagery analysis applications. The advancements facilitated by this research are instrumental in ecological assessments, conservation efforts, and resource management strategies, signaling a leap forward in the era of environmental monitoring and analysis.

The increasing emergence of multidrug resistant (MDR) pathogens causes difficult-to-treat infections, with long-term hospitalizations and high incidence of death, thus representing a global public health problem. To manage MDR bacteria bugs, new antimicrobial strategies are necessary, and their introduction in practice is a daily challenge for scientists in the field. An extensively studied approach to treat MDR infections consists in inducing high levels of reactive oxygen species (ROS) by several methods. Although further clinical investigations are mandatory on the possible toxic effects of ROS to mammalian cells, clinical evaluations are extremely promising, and their topical use to treat infected wounds and ulcers, also in presence of biofilm, is already clinically approved. Biochar (BC) is a carbonaceous material obtained by pyrolysis of different vegetable and animal biomass feedstocks, at 200−1000 °C in limited presence of O2. Recently, it has been demonstrated that BC capability of removing organic and inorganic xenobiotics is mainly due to the presence of persistent free radicals (PFRs), which can activate oxygen, H2O2 or persulfate in the presence or not of transition metals by electron transfer thus generating ROS, which in turn degrade pollutants by advanced oxidation processes (AOPs). In this context, the antibacterial effects of BC containing PFRs have been demonstrated by some authors against Escherichia coli and Staphylococcus aureus, thus giving birth to our idea of the possible use of BC-derived PFRs as a novel method capable of inducing ROS generation for antimicrobial oxidative therapy. Here, the general aspects concerning ROS physiological and pathological production and regulation, and the mechanism by which they could exert antimicrobial effects have been reviewed. The methods currently adopted to induce ROS production for antimicrobial oxidative therapy have been discussed. Finally, for the first time, BC-related PFRs have been proposed as a new source of ROS for antimicrobial therapy via AOPs.