Nuclear waste is one of the most important environmental problems of nuclear power plants. A novel renewable distillation method has been proposed for an on-site recycling of the spent nuclear fuel and separation of its valuable components from the fissile isotopes, which is especially applicable for reactors using liquid fuels.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

Computational methods are essential to support and advance nuclear technologies due to the hazards of handling and analysing highly radioactive materials such as spent nuclear fuel (SNF). However, many such methods, including those thatcan predict SNF compositions and decay heat parameters, require expensive, proprietary software, alongside significant programming experience and computational power for utilisation, severely limiting availability of data and hampering research throughput. Although some datasets are available, many are incomplete or only cover certain fuel systems for older reactor types. Research investigating new methods for SNF recycling, for example, requires compositional and decay heat data for fuel systems not covered by extant data, though analogous source data may be available. With this in mind, we have developed a simple, accessible, and flexible method for extrapolation of isotopic, elemental, and decayheat compositions for SNF at discharge and following decay storage before recycling, based on an extant dataset. This semi-empirical method uses physical and mathematical first principles and can be performed using software accessible to all researchers. This provides outputs accurate to within 1% of reference values interpolated within the range of available data for isotopic compositions, with sensible extrapolations at higher burnups beyond those reported, withoverall elemental outputs accurate to within 0.1%of expected totals. In this publication, we present the developmental methodology, some sample data, the present limitations, and options for future development and expansion of functionality.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

Soft materials bearing rigid, lightweight, and vibration-dampening properties offer distinct advantages over traditional wooden and metal-based fillings for spent fuel transport casks, due to their low density, tunable structure, excellent mechanical properties, and ease of processing. In this study, a novel type of rigid polyurethane foams is prepared using a conventional polycondensation reaction between isocyanate and hydroxy groups. Moreover, the density and size of the pore in these foams are precisely controlled through simultaneous gas generation. The as-prepared polyurethane exhibits high thermal stability exceeding 185 °C. Lifetime predictions based on thermal testing indicate that these polyurethane foams could last up to over 60 years, which is double lifetime of conventional materials of about 30 years. Due to their occlusive structure, the mechanical properties of these polymeric materials meet the design standards for spent fuel transport casks, with maximum compression and tensile stresses of 6.89 and 1.37 MPa, respectively, at a testing temperature of -40 °C. In addition, these polymers exhibit effective flame retardancy; combustion ceased within 2 s after removal of the ignition source. All in all, this study provides a simple strategy for preparing rigid polymeric foams, presenting them as promising prospects for application in spent fuel transport casks.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Molten LiCl-KCl salt and liquid cadmium are proposed as the electrolyte and the reactive cathode for the electrorefining of spent nuclear fuels. Corrosion testing of existing alloys is mandatory to ensure the service life of the electrorefiner vessel and electrode assemblies. Haynes C276, Inconel 600, AISI 316L stainless steel, and 42CrMo low alloy steel were exposed to LiCl-KCl melt at 500°C for 500 h in an argon atmosphere. All alloys suffered from dissolution attacks with the presence of oxide islands or porous oxide layer on the surface. AISI 316L, T91 steel and tungsten specimens were also submitted to corrosion tests in liquid cadmium at 500°C for 120 h. Corrosion of AISI 316L and T91 stainless steel were predominated by chemical oxidation with additional severe Ni dealloying occurred on AISI 316L. Tungsten only suffered from dissolution attack in comparison.

The rapid and accurate detection of viruses and the discovery of single nucleotide polymorphisms (SNPs) are crucial for disease management and understanding viral evolution. In this study, a pipeline for virus detection, validation, and SNP discovery from next-generation sequencing (NGS) data is presented. By integrating state-of-the-art bioinformatics tools with artificial intelligence, the pipeline processes raw sequencing data to identify viral sequences with high accuracy and sensitivity. Before aligning the reads to the reference genomes, quality control measures and adapter trimming are performed to ensure the integrity of the data. Unmapped reads are subjected to de novo assembly to reveal novel viral sequences and genetic elements. The effectiveness of the pipeline is demonstrated by the identification of virus sequences, illustrating its potential for the detection of known and emerging pathogens. SNP discovery is performed using a custom Python script that compares the entire population of sequenced viral reads to a reference genome. This approach provides a comprehensive overview of viral genetic diversity and identifies dominant variants and a spectrum of genetic variations. The robustness of the pipeline is confirmed by the recovery of complete viral sequences, which improves our understanding of viral genomics. This study highlights the synergy between traditional bioinformatics techniques and modern approaches, providing a robust tool for analyzing viral genomes and contributing to the broader field of viral genomics.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

With the influence of Big Data culture on qualitative data collection, acquisition, and processing, it is becoming increasingly important that social scientists understand the complexity underlying data collection and the resulting models and analyses. Systematic approaches for creating computationally tractable models need to be employed in order to create representative, specialized reference corpora subsampled from Big Language Data sources. Even more importantly, any such method must be tested and vetted for its reproducibility and consistency in generating a representative model of a particular population in question. This article considers and tests one such method for Big Language Data downsampling of digitally-accessible language data to determine both how to operationalize this form of corpus model creation, as well as testing whether the method is reproducible. Using the U.S. Nuclear Regulatory Commission's public documentation database as a test source, the sampling method's procedure was evaluated to assess variation in the rate of which documents were deemed fit for inclusion or exclusion from the corpus across four iterations. The findings of this study indicate that such a principled sampling method is viable, thus necessitating the need for an approach for creating language-based models that account for extralinguistic factors and linguistic characteristics of documents.

MicroRNAs are small non-coding RNAs, which contribute to the regulation of many physiolog-ical and pathological processes. Conventionally, miRNAs perform their activity in the cyto-plasm, where they regulate gene expression by interacting in a sequence-specific manner with mature messenger RNAs. Recent studies point to the presence of mature miRNAs in the nucleus. This review summarizes current findings regarding the molecular activities of nuclear miRNAs. These molecules can regulate gene expression at the transcriptional level by directly binding DNA on the promoter or the enhancer of regulated genes. MiRNAs recruit to these regions dif-ferent protein complexes, resulting both in activation or repression of transcription, through a number of molecular mechanisms. Haematopoiesis is presented as a paradigmatic biological process whereby nuclear miRNAs possess a relevant regulatory role. Nuclear miRNAs may af-fect gene expression also acting on nuclear mRNA processing and on the biogenesis of miRNA themselves by regulating pri-miRNA maturation. Overall, nuclear miRNAs are biologically ac-tive molecules that can be critical for the fine tuning of gene expression and deserve further studies in a number of physiological and pathological conditions

Kisspeptin (KISS1) and its cognate receptor (KISS1R) are implicated in the progression of various cancers. However, a theranostic radiopharmaceutical targeting the KISS1 receptor (KISS1R) has yet to be explored. A gallium-68 labelled kisspeptin-10 (KP10) has potential as a pan-tumor radiopharmaceutical for the detection of cancers. Furthermore, a lutetium-177 labelled KP10 could find therapeutic application in treating oncological diseases. We attached DOTA to the NH2-terminus of KP10 as we posited that this modification would not impair biological activity and showed that receptor stimulation of inositol phosphate accumulation in HEK293 transfected with the KISS1R gene was similar for KP10 and DOTA-KP10. We describe optimization of radiolabeling with gallium-68 and lutetium-177 and stability in serum, plasma, and whole blood. Pharmacokinetics was established with µPET/CT and ex vivo measurements. Dynamic studies with µPET/CT demonstrated that background clearance for the radiopharmaceutical was rapid with a blood half-life of 18 ± 3 minutes. DOTA-KP10 demonstrated preserved functionality at KISS1R and good blood clearance. These promising results advocate the further development of KP10 structures which have high binding affinity along with proteolytic resistance.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Depressions containing partially molten rocks were investigated in Quaternary pebbly sedi-ments in Alpine foreland in Bavaria, Germany. Ruins of limekilns from 18-19th centuries are abundant around Seeshaupt. They are usually associated with earthworks for fuel feeding and protection from wind. Depressions contain partially molten stones from furnace walls, with lime and burnt loam remnants. On the surface of pebbles (typically gneisses), green glass formed with chemical composition possibly affected by moderately volatile components of wood biomass, mainly K and Cu. Thermoplastic deformation of pebbles is limited and the sur-face melt deformation points to slow flow. At Emmerting, on the other hand, two walled circu-lar depressions which lack additional earthworks have been identified as possible impact cra-ters. Thermally affected pebbles show much more intense deformation. Colorless to greenish glass, also K and Cu enriched, usually forms only thin surface coatings, in places covered by younger melt extruded from pebble interior. Burnt loam is missing. At Grabenstätt-Kaltenbach, a depression of unclear origin was investigated. Morphologically, it matches craters rather than limekilns, but anthropogenic contamination (brick-like material) is probable. The rare molten samples do not display extreme deformation features. The thermally affected stones, mainly those from Emmerting, have elevated magnetic susceptibility.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

The inclusion of spent hemp biomass (SHB), an extracted byproduct from industrial cannabidiol (CBD) production, in the diets of dairy cows and lambs appear to be safe with minor effects on the metabolism, including a decrease of circulating cholesterol and increase bilirubinemia, both associated with liver metabolism. Those effects could be consequence of the presence of cannabinoids, particularly Δ9-tetrahydrocannabinol (THC) and CBD in the SHB. This study aimed to study the transcriptional profile of the liver of dairy cows and lambs fed SHB. Dairy cows received SHB or alfalfa pellet for four weeks of intervention (IP) and four weeks of withdrawal periods (WP). Finishing lambs were fed a control diet (CON), 10% (LH2) or 20% (HH2) SHB for 2 months or 1 month followed by 1-month SHB withdrawal (LH1 and HH1, respectively). RNA sequencing was performed, and the mRNA was annotated using the latest reference genomes. The RNAseq data were filtered, normalized for library size and composition, and statistically analyzed by DESeq2. The bioinformatic analysis was performed by using DAVID, Gene Set Enrichment (GSE) analysis, and the Dynamic Impact Approach. Using a 0.2 FDR cut-off, we identified only ≤24 differentially expressed genes (DEG) in the liver by feeding SHB in dairy cows and a larger number of DEG in lambs (from 71 in HH1 vs. CON to 552 in LH1 vs. CON). The KEGG analysis demonstrated that feeding SHB in dairy cows and lambs had relatively minor to moderate metabolic alterations in dairy cows and lambs mainly associated with amino acids and lipid metabolism whereas cholesterol synthesis was overall activated in lambs. GSE analysis identified activation of PPAR signaling pathway only in dairy cows. We found an opposite effect on activation of metabolism of drug and xenobiotics by cytochrome P450 enzymes in dairy cows and lambs receiving less SHB but an inhibition in HH2 lambs. Immune system-related pathways were inhibited by feeding SHB in lambs, but the impact was minor. Cumulatively, inclusion of SHB containing cannabinoids in dairy and lambs demonstrate very little effects on the alteration of transcriptomic profile of the liver.

In this contribution, we make an attempt to write a theoretical proposal for designing an eco friendly thermal power plant which runs with cold nuclear fusion technology at a temperature of (1500 to 2000) deg.C. In our recently published papers, we have proposed a clear cut mechanism for understanding and implementing cold nuclear fusion technique pertaining to fusion of hydrogen with metals of mass numbers starting from 50. In this context, we would like to stress the point that, fusion of hydrogen under controllable temperature and pressure can be understood as a phenomenon of fusing neutron to the nucleus of the base atom. Part of isotopic nuclear binding energy difference of final and base atomic nuclides can be seen in the form of safe thermal energy of the order of (1 to 3) MeV per atom against 200 MeV released in nuclear fission of one Uranium atom. Due to increased heaviness and weak interaction, sometimes fused neutron splits into proton and electron. Proton seems to be retained by the base atom’s nuclear core and electron seems to join with the electronic orbits of the base atom. In this way, increased mass of base atomic nuclide helps in eco friendly production of thermal energy in large quantity. For this purpose we consider Iron-56 as a fuel. In a simplified view, under strong nuclear attractive forces, Iron-56 absorbs hydrogen atom as a neutron and by emitting 1MeV equivalent thermal energy transforms to Iron-57. Thus, one gram of Iron-56 can generate 1000MJ of heat with 50% efficiency. In a shortcut approach, by bombarding powder and semi-liquid forms of Iron-56 with direct neutrons coming from neutron source, our proposal can be tried, understood and verified experimentally.

In this work, the surface of poly(ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670-1310 nm was hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spec-troscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurement were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymeriza-tion time 60 min, monomer concentration of 30% and distance from the UV-source 7 cm. The wa-ter contact angle of the modified membranes reached 97° which is 51o for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effect of membrane pore size, the degree of grafting and salt concentration on the performance of membrane distillation process was investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

In the last three decades the presence of phospholipids in the nucleus has been shown and thoroughly investigated. A great interest raised about nuclear inositol lipids mainly because of their role in signalling acting. Here we review the main issues of nuclear phospholipid localization and the role of nuclear inositol lipids and their related enzymes in cellular signaling both in physiological and pathological conditions.

The microstructure evolution during the cold rolling and subsequent annealing of Alloy 800H was investigated. Two distinct rolling methods, unidirectional rolling and cross-rolling, were intro-duced. Results show that better ductility was observed in the unidirectional rolling than in cross-rolling, whilst a higher volume fraction of large deformed grains was observed in the cross-rolled plates than in the unidirectionally rolled plates. Recrystallization occurred faster in plates from unidirectional rolling than from cross-rolling.

In this work, we studied light-output properties, efficiency function as well as PSD capability of p-Terphenyl scintillator. The selected solid cylindrical scintillation detector has a size of (45 x 45) mm with PSD properties. Recently presented studies of light-output functions have been measured only for low neutron energies. Our motivation has been to determine more accurate the light output function for p-Terphenyl scintillator over a wider neutron energy range.

The paper describes an application of machine learning approach for parameter optimization. The method is demonstrated for the elasto-viscoplastic model with both isotropic and kinematic hardening. It is shown that the proposed method based on long-short term memory networks enabled to obtain reasonable agreement of stress-strain curves for cyclic deformation in low-cycle fatigue regime. The main advantage of the proposed approach over traditional optimization schemes lies in the possibility to get parameters for a new material without the necessity to conduct any further optimizations. As the power and robustness of the developed method was demonstrated on the very challenging problem (cyclic deformation, crystal plasticity, self-consistent model, isotropic and kinematic hardening), it is directly applicable to other experiments and models.

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

The high dependence on light crude oil as the main source of energy in automobiles., industrial processes, source of raw material for various industrial synthesis have made the heavy crude more available in the world and open for research work on its potentials as a source of energy for the increasing population of the world in areas like energy source for powering big marine engines, energy source in heavy industrial machines e.t.c. Though the relatively unfavourable characteristics of heavy fuel oil such as; high viscosity, high probability of precipitating is a reasonable challenge to the possible utilization of heavy fuel as a source of energy in the areas highlighted above. These issues of heavy fuel oil are largely due to the presence of Asphaltene in it which is a large complex hydrocarbon in heavy fuel oil. Understanding the combustion potential of asphaltene is therefore an interesting and challenging problem that has attracted increasing attention from both academia and industry. This research work is aimed at carrying combustion studies on the Forcados (Ni-geria) heavy fuel fraction asphaltene HFFA extracted from Forcados crude Oil and examining its combustion characteristics with the view to examine it for future sweet heavy fuel generation for it source got low sulphur content, to ascertain the volatile composition, moisture and ash content. The HFFA extracted to determine physical characteristics of the HFFA extracted for fuel properties potentialities and this study was carried out to evaluate the chemical constituents of forcadous asphaltene lead-ing to the generaration of HFFA using GCMS. The Forcados asphaltene showed some good fuel properties when subjected to ce-tane number, API gravity, flash point and cloud point parameter test. Probing further with AAS for trace metal presence showed some high concentration on Chromium (Cr), Nickel (Ni), Iron (Fe), Lead (Pb), Cadmium (Cd), Copper (Cu), Manganese (Mn) and Zinc (Zn) indicating the potential for residual and soot formation after combus-tion. But still being a sweet asphaltene from Nigerian sweet crude source will be de-void of corrosive effect on machineries and heavy fuel engine if used to power it as in the case of high sulphur content in Venezuelan crude oil and some other world. The GCMS showed the decomposition of heavy crude asphaltene peaks and sig-naling the presence of heavy fuel fraction in the composition of the asphaltene while the FTIR and the UV-VIS identified the various functional groups in the compounds and the identification of signals that cannot be seen in the normal spectrum respec-tively.

To support the integration of renewable energy sources and preserve grid stability, this study examines several approaches for controlling the temperature of Battery Energy Storage Systems (BESS) in modern energy settings. Specifically, the usage of BESS in Virtual Power Plants (VPPs) is the focus of this study. The effectiveness, safety features, dependability, affordability, and suitability for VPP applications of these systems are examined. Among the various hybrid cooling alternatives, two particularly promising combinations emerge. Firstly, the integration of heat pipes and phase change materials leverages their ability to conduct heat efficiently away from heat sources with minimal temperature differences, making them excellent for rapid heat transfer. Secondly, an approach employing heat pipes and liquid passive cooling a combination that capitalizes on the efficient heat transfer capabilities of heat pipes and the consistent cooling offered by liquid passive systems. The study underscores the importance of improving BESS performance and sustainability within VPPs by providing useful recommendations for choosing the best thermal management system depending on climate conditions and geographic location.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

The nuclear reactor measurement system is a crucial component of the nuclear measurement system in a nuclear power plant. Its primary function is to measure the power distribution within the reactor core using detectors, calibrate, and provide data on core fuel consumption. Therefore, the study of the detectors' reliability is crucial for ensuring the safe operation of the nuclear power system. The article describes the operational mechanism of the gas ionization chamber detector utilized in the intermediate-range detector of the off-board nuclear measurement system. It also analyzes the movement of particles between the plates during the ionization process of the nuclear reaction taking place in the detector. The functional relationship between the current in the recombination region and the ionization region involved in the actual working condition, and the change with the increase of voltage between the plates, is deduced. A mathematical model is established for the number of pulses generated between the plates and the magnitude of the voltage between the plates. Subsequently, the change in the offset of the voltage corresponding to the inflection point of the ping curve and the change rule of the slope of the ping curve are investigated. Combined with the analysis of experimental data, the results show that the initial particle energy of Ar+, the primary sensitive particle on the detector surface, follows a normal distribution and is influenced by the energy loss associated with the initial velocity and the voltage between the plates. The trends of the inflection points and slopes of the ping curves can be utilized to evaluate the performance and operational status of the detector. Combined with the results of the experimental data analysis, the fit is good, and the inflection point currents in the normal state decrease by about 1.5% annually. The intelligent diagnostic system, based on the method studied in this paper, has been successfully implemented in the RPN digital retrofit and upgrade project at Qinshan No. 2 Plant.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

Investigation of functional magnetic resonance imaging (fMRI) data with machine learning (ML) techniques, including also deep learning (DL) methods, have been widely used to study Autism Spectrum Disorder (ASD). This disorder is characterized by symptoms that affect the individual’s behavioral aspects and social relationships. Early diagnosis is crucial for intervention, but the complexity of ASD poses challenges for treatment development. This study compares traditional ML techniques with deep learning (DL) methods in the analysis of functional connectivity measures obtained from the time series of multicentric ABIDE dataset. Specifically, Support Vector Machines (SVM) classifiers, with both linear and Radial Basis Function (RBF) kernels, as well as eXtreme Gradient Boosting (XGBoost) classifiers, are compared against the TabNet classifier, which is a DL architecture customized for tabular data analysis and a Multi Layer Perceptron (MLP). The findings suggest that DL classifiers may not be optimal for the type of data analyzed, as their performance trails behind that of standard classifiers. SVMs achieve performances, in terms of AUC, around 75%, compared to the best TabNet and MLP results, which are 65% and 71%, respectively. Additionally, this work investigates the brain regions that contribute most to the classification task, which are found to be those primarily responsible for sensory and spatial perception, as well as attention modulation, known to be altered in ASD.

The Atmospheric Dynamics Mission ADM-Aeolus was successfully launched in August 2018 by the European Space Agency (ESA). The Aeolus mission carried a single instrument, the first-ever Doppler Wind Lidar (DWL) in space, called Atmospheric LAser Doppler INstrument (ALADIN). Aeolus circled the Earth in a polar sun-synchronous orbit at about 320 km altitude with a repeat cycle of 7 days, providing vertical profiles of horizontal line-of-sight (HLOS) winds on a global scale. Exceeding scientific expectations, Aeolus, initially designed for a 3-year lifetime, provided global coverage of wind profiles for almost five years. In this long-term validation study, we assessed the accuracy of the Level 2B (L2B) Rayleigh-clear and Mie-cloudy wind products by collecting radiosonde data from three stations in the Brazilian Amazon: Cruzeiro do Sul (7.62° S, 72.67° W), Porto Velho (8.76° S, 63.91° W), and Rio Branco (10.00° S, 67.80° W). Statistical validation was conducted by comparing Aeolus L2B wind products and radiosonde data, launched daily at 12:00 UTC from October 2018 to March 2023. Considering all data collected during the mission period, Pearson’s coefficient (R) of 0.73 was observed in Rayleigh-clear and 0.85 in Mie-cloudy, revealing a strong correlation between Aeolus and radiosonde winds. No significant biases were detected, with values of -0.14 m/s for Rayleigh-clear and -0.40 m/s for Mie-cloud, fulfilling the mission requirement of having absolute biases below 0.7 m/s. However, when analyzed annually, in 2022, the bias for Rayleigh-clear was -0.95 m/s, exceeding the mission requirements.

The Shimensi super-large tungsten polymetallic deposit is located in Late Jurassic- Early Cretaceous Porphyry-Skarn tungsten ore belt in the south Yangtze metallogenic belt. There are 3 types of mineralization: veinlet-disseminated type, thick quartze vein type and hydrothermal crypto-explosive breccia type. Based on geological studies, this paper presents new petrographic, microthermometric, laser Raman spectroscopic and hydrogen and oxygen isotope research of the fluid inclusions from the deposit. The results show that there are five different types of fluid inclusions: liquid-rich inclusions, vapor-rich inclusions, pure liquid inclusions, pure vapor inclusions, and fluid inclusions containing a solid crystal. The homogenization temperatures of the fluid inclusion range from 140℃-270℃, the salinities are 3%-5% NaCleq and the densities of ore-forming fluid range from 0.64 g/cm3 to 0.99 g/cm3. For the analyses of Laser Raman spectroscopic, the ore-forming fluids can be approximated by a Ca2+-Na+-SO42--Cl- fluid system with small amount of CO2, CH4 and N2. Otherwise, the datas of the pressure, pH and Eh show a fluid metallogenic environment of low pressure, weak acid and weak reduction. The values of the homogenization temperature in 3 types of orebodies suggest that the mineralization is characterized by the decrease of the temperature under the condition of the fluid immiscibility. The H-O isotope values are interpreted to indicate that the ore-forming fluids are mainly composed of magmatic water, and also the meteoric water was added with the process of the magma rising.

The importance of personalized medicine is growing, since there is an urged need to avoid unnecessary and expensive treatments. In nuclear medicine, the theranostic approach is an established tool for a specific molecular targeting in means of diagnostics and therapy. The visualisation of potential targets can help to predict if a patient would benefit from a particular treatment or not. Thanks to the quick development of radiopharmaceuticals and diagnostic techniques, the use of theranostic agents is constantly rising. In this article important milestones of nuclear therapies and diagnostics in the context of theranostics are highlighted. It begins with the well-known radioiodine therapy in patients with thyroid cancer and then guides through different approaches for the treatment of advanced cancer with targeted therapies. The aim of this review is to provide a summary of background knowledge, current applications and advantages of targeted therapies and imaging in nuclear medicine practice.

Bulk composition, mineralogy and microchemistry of various fractions of the filling of the Crater No. 4 at Emmerting were investigated. Here we present mainly the fine fractions, which, in contrast to pebbles larger than ca. 4 cm, are relatively poor in material affected by melting. A 0.1 mm long meteorite fragment without ablation features was found, and remelted fragments of the same body have been identified. The projectile was dominated by enstatite, also containing forsterite, basic plagioclase, Ni-rich pyrrhotite and troilite, kamacite, silica, and probably merrillite. The molten fragments contain porous Mg-rich glass (indicating temperature > 1500 °C), minor Fe oxides, and occasionally uncommon Ni-rich minerals. The bulk composition and electron microprobe show that the amount of meteoritic material is low (<< 1 %), and it is not unequivocally manifested even in platinum-group elements abundances and osmium isotope ratios (the latter, however, were only measured in two samples). This can be explained by dilution of the filling by particles brought after the crater formation, and by probably achondritic composition of the projectile. Relatively large hollow spheroid Fe oxide particles were observed in thin sections from the magnetic fraction. A Mn oxide hollow spherule has also been found. In magnetically separated filling from the nearby Crater No. 5, bulk chemical composition points to contamination with several metals and metalloids probably due to influence of recent alluvial sediments. Therefore, the extent of meteoritic contamination in this crater may be even smaller.

In this paper, we study the effect of decreasing aperture diameter on signal transmission from the scintillator to the PMT. The apertures have been inserted directly between the scintillator and the photomultiplier. Three different aperture diameters have been used over a wide energy range.A newly developed fast digital spectrometer has been utilised for experimental measurement in the radial channel of the VR-1 research reactor. The detector signals with and without inserted apertures have been measured and evaluated. The aim of our research was to determine the effect of the apertures on the spectral quality, energy range and the evaluated physical quantities.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

In this paper, the time-resolved model of photoacoustic signal for samples with a complex inner structure is derived including local non-equilibrium of structural elements with multiple degrees of freedom, i.e. structural entropy of the system. The local non-equilibrium is taken into account through the fractional operator. By analyzing the model for two types of time-dependent excitation, a very short pulse and a very long pulse, it is shown that the rates of non-equilibrium relaxations in complex samples can be measured by applying the derived model and time-domain measurements. Limitations of the model and further directions of its development are discussed.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

This study introduces numerical advancements in an alternative design for the SPS Beam Dump Facility (BDF) at CERN. The design envisions a high-power operation target made of flowing liquid lead. The BDF is a proposed versatile facility at CERN, intended for both beam-dump-like and fixed-target experiments. The target behavior is assessed, assuming a proton beam with a momentum of 400 GeV/c, a pulse frequency of 1/7.2 Hz, and an average beam power of 355 kW. An evaluation is conducted using various Computational Fluid Dynamics (CFD) codes to analyze the behavior of liquid lead and to predict the thermal stress on the target vessel induced by the pulsed heat source generated by the charged particle beam. The comparison increases the reliability of the results, investigating the dependencies on the CFD modeling approach. The beam is modeled as a volumetric heat source with data coming from beam-lead interaction simulations provided by CERN and obtained with the Monte-Carlo code FLUKA. The velocity field and stress profiles are utilized to enhance the design of the lead loop and verify its viability and safety when operated with a liquid metal target.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

The Capon algorithm can be applied to reprocess SAR images, resulting in super-resolution super-resolution reconstructed scenes with lower sidelobe levels. Base on this idea, we have proposed a processing chain of Super-Resolution Persistent Scatterer Interferometry (SR-PSI), to increase PS density. In this paper, we review the main aspect of SR-PSI. We also propose a revised robust Capon algorithm. The result of real-life Sentinel-1 (S-1) data is shown.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

Many of the fundamental molecules of life share extraordinary pigment-like optical properties in the long-wavelength UV-C spectral region. These include strong photon absorption and rapid (sub pico-second) dissipation of the induced electronic excitation energy into heat through peaked conical intersections. These properties have been attributed to a ``natural selection'' of molecules resistant to the dangerous UV-C light incident on Earth's surface during the Archean. In contrast, the ``thermodynamic dissipation theory for the origin of life'' argues that, far from being detrimental, UV-C light was, in fact, the thermodynamic potential driving the dissipative structuring of life at its origin. The optical properties were thus the thermodynamic ``design goals'' of microscopic dissipative structuring of organic UV-C pigments, today known as the ``fundamental molecules of life'', from common precursors under this light. This ``UV-C Pigment World'' evolved towards greater solar photon dissipation through more complex dissipative structuring pathways, eventually producing visible pigments to dissipate less energetic, but higher intensity, visible photons, up to wavelengths of the ``red-edge''. The propagation and dispersal of organic pigments, catalyzed by animals, and their coupling with abiotic dissipative processes, such as the water cycle, culminated in the apex photon dissipative structure, today's biosphere.

A dioxomolybdenum catalyst [(MoO2Cl2-O-MoO2Cl2)(L)] (1) (with L (1S,2S)-N,N´-bis(2-pyridinecarboxamide)-1,2-cyclohexane) was prepared and used as catalyst for the desulfurization of a multicomponent model fuel containing the most refractory sulfur compounds in real fuels. This complex showed to have a high efficiency to oxidize the aromatic benzothiophene derivative compounds present in fuels, mainly using a biphasic 1:1 model fuel/MeOH system. This process conciliates catalytic oxidative and extractive desulfurization, occurring the oxidation of the sulfur compounds in the polar organic solvent. The oxidative catalytic performance of (1) showed to be influenced by the presence of water in the system. Using 50% aq. H2O2 it was possible to reuse the catalyst and the extraction solvent MeOH during ten consecutive cycles without loss of desulfurization efficiency.

Background/Objectives: Although the role of F-18 FDG PET/CT imaging is well established in oncology, its diagnostic value in routine monitoring for recurrent colorectal cancer (CRC) is still controversial. The aim was to evaluate the diagnostic value of FDG PET/CT in detecting recurrent CRC in correlation with CEA, CA 19-9 levels, and conventional imaging modalities (CIM). Methods: Between 2009 and 2023, we retrospectively studied 134 CRC patients referred for FDG PET/CT imaging on the suspicion of recurrence based on elevated CEA and/or CA 19-9, and/or equivocal radiological findings. According to the Institutional Tumor Board CRC protocol, after initial treatment which was dependent on TNM stage (neoadjuvant therapy, primary resection or adjuvant treatment), patients underwent a standard 5-year surveillance including CEA and CA 19-9 measurements, CIM, and colonoscopy every 6 months. The statistics including univariate and multivariable analyses were conducted using the IBM SPSS 20.0 statistical software. P-values <0.05 were considered statistically significant. Results: Recurrent CRC was confirmed in 54/134 (40.3%) patients with elevated tumor markers. FDG PET/CT shows high diagnostic performance in detecting recurrent CRC with sensitivity, specificity, PPV, NPV, and accuracy of 94.4%, 82.5%, 78.5%, 95.7%, and 87.3%, respectively. The CEA shows a high sensitivity of 98.1%, but both low specificity and accuracy of 15% and 48.5%, respectively. The sensitivity, specificity, and accuracy, for CA 19-9 and CIM for the correct diagnosis in CRC patients were: 44.4%, 67.5%, 58.2%, and 51.9%, 98.8%, 79.9%, respectively. The AUC for FDG PET/CT, elevated CEA levels, CIM, and elevated CA 19-9 levels was 0.885 (95% CI: 0.824-0.946; p<0.001), 0.844 (95% CI: 0.772-0.916; p<0.001), 0.753 (95% CI: 0.612-0.844; p<0.001); and 0.547 (95% CI: 0.442-0.652; p=0.358). Univariate analysis shows that both FDG PET/CT- and CIM-positive results were highly associated with CRC recurrence (p<0.001 and p<0.001, respectively), while gender, mucinous tumor type, presence of initial lymph node metastasis (N+), and presence of initial distant metastasis (M+) have no significance (p=0.211, p=0.158, p=0.583, and p=0.201, respectively). Our multivariate analysis shows that independent predictors for CRC recurrence are: positive FDG PET/CT scans (p<0.001), positive CIM results (p=0.001) and elevated CA19-9 levels (p=0.023). Although CA 19-9 was not detected as a statistically significant predictor in the univariate analysis (p=0.358), in a multivariate analysis it was recognized as a significant predicting factor in detecting CRC recurrence (p=0.023). Conclusions: FDG PET/CT shows a high diagnostic efficacy in CRC recurrence detection, in correlation with CEA levels, CA 19-9 levels, and CIM. This imaging modality should be routinely integrated into the postoperative follow-op in patients with elevated tumor markers.

We have repeated the experiment performed recently by Krasznahorkay et al., (Phys. Rev. Lett. 116, 042501 (2016)), which may indicate a new particle called X17 in the literature. In order to get a reliable, and independent result, we used a different type of electron-positron pair spectrometer which have a more simple acceptance/efficiency as a function of the correlation angle, but the other conditions of the experiment were very similar to the published ones. We could confirm the presence of the anomaly measured at the Ex=18.15 MeV resonance, and also confirm their absence at the Ex=17.6 MeV resonance, and at Ep= 800 keV off resonance energies.

Abstract: Imaging of low (LGG) to high (HGG) grade gliomas is conventionally performed with MRI, which is the non-invasive gold-standard imaging modality to derive data. Gliomas (Grade 1,2,3,4) are lethal and demonstate poor outcomes despite novel therapies. Integrins compose of heterodimeric parasympathetic nervous system; the aVb3 (RGD i.e. Galacto-Arginine-Glycine-Aspartic acid) have been displayed as a potential biomarker that can be imaged via PET in order to trace the angiogenetic pathway. Gliomas are common primary central nervous system (CNS) tumours which are often pose a diagnostic challenge, even to stage and manage because of their heterogeneity in molecular aberrations. Several core mutational core hallmarks of gliomas are inducing/accessing vasculature, tumour promoting inflamation, polymorphic microbes and avoiding/resisting cell death; these ultimately lead to poor prognosis. In 2007, the classification of diffuse gliomas was based on the histopathology and subtype e.g. Pilocytic astrocytoma and low cell proliferation, in 2016, the classification of diffuse gliomas was based on the IDH status, 1p/19q codeletion, subtype and grade; then in 2021, the IDH status (wild-type or mutant), molecular profile, subtype and grade were added in order to improve the classification of diffuse gliomas. Imaging (MRI) techniques progress stalled despite the imperfections in MRI e.g distinguishing RN (radionecrosis) and PsP (Pseudoprogression) hence the exploration of PET probes that detect important hallmarks of gliomas e.g. techniques such as [68Ga]68Ga-RGD positron emission tomography (PET) to be utilised to assess vasculature. This case report aimed to determine the potential clinical utility of molecular imaging with 68Ga-RGD PET used in complementary to traditional MRI techniques.

The German health authorities' guidelines for medical devices in 2012 highlighted the importance of cleaning ultrasound probes, emphasizing their validation and reliability. In addition to automated and validated options, alternative manual methods such as wipe disinfection have gained traction due to their independence from additional hardware. The study examines the effectiveness of manual disinfection methods, specifically the cleaning process, addressing concerns raised by the Robert Koch Institute regarding the lack of validation for wipe disinfection of semi-critical devices. The EQUINOS colored wipe disinfection kit identified wetting gaps in all cleanings across four probes tested. The results indicate significant challenges in ensuring complete surface wetting, particularly in complex body parts such as clip-on areas and shapes for additional biopsy attachments, suggesting that manual methods alone may not adequately mitigate the risk of infection transmission (p value .001). The study concludes that while manual disinfection methods are a viable alternative to automated reprocessing, there is a critical need for enhanced training and potentially the development of more effective manual disinfection techniques or colored wipes to ensure patient safety and compliance with healthcare hygiene standards.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

In this study, a summary of the processes performed on the SPL for recycling, reduction in toxicity and treatment were examined on an industrial and laboratory scale. In writing this research, an attempt has been made to address the useful processes that have taken place in this field. Spent pot lining or SPL is a type of solid waste that is produced in the aluminum production process. After 3 to 8 years, the cathode blocks become problematic and can no longer be used, and need to be replaced due to adverse effects on cell function. SPL is known to be a hazardous waste to nature due to its fluoride and cyanide content. Research has shown that SPL ingredients have destructive and very dangerous effects on human DNA, which is why they are so important to maintain and recycle.

The pyrolysis process has emerged as an attractive option for waste treatment. In this technology, inorganic compounds play catalytic effects in the pyrolytic reaction of organic materials, increa-sing the char's yield, porosity, and physicochemical properties. The present research investigates and compares the slow pyrolysis of spent coffee grounds (SCG) using potassium hydroxide (KOH) (weight ratio of 1:1) and landfill leachate membrane concentrate (LLMC) residue (weight ratio of 1:1) as pyrolitic additives. We hypothesized that the high content of alkali and alkaline earth metals in LLMC could enhance the yield or improve the quality of the carbon-based material produced in pyrolysis. This strategy could be a sustainable alternative for valorizing SCG and landfill wastes, replacing catalyzing agents such as steam, CO2, and chemical additives used on an industrial scale. The char yields in slow pyrolysis ranged from 18 to 24%. The SCG had a low specific surface area (4.5 m2 g-1), contrasting with the notable surface areas observed in both ac-tivated chars. In particular, the KOH-activated char displayed a higher surface area than the LLMC-activated char (1960 vs. 1130 m2 g-1). On the other hand, the combustion enthalpy of the LLMC-activated material was estimated at 22 MJ kg-1. This value was 22% higher than the energy enthalpy of SCG and KOH-activated char used for comparison. Our findings confirm that pyrolysis of SCG with KOH produces a microporous material with a high specific surface area. In contrast, the resulting LLMC-activated char demonstrates a higher calorific value. Our findings could contribute to establishing potential industrial applications for SCG and LLMC residues to produce energy and high-value materials.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

In the last decades the primordial black holes ({\bf pbhs}) have attracted much attention of cosmologists and astrophysicists. This is associated with origination of such black holes in the early Universe as a result of a gravitational collapse of the high-density matter, making them natural ''detectors'' of the processes involved. In inflationary cosmology of particular importance are {\bf pbhs} originated during the pre-inflationary period. And, since they are small and generated at the energies close to the Planck energies, for them we should take into consideration the quantum-gravitational corrections ({\bf qgcs}). In turn, these corrections change (shift) the inflationary parameters. The paper presents a study of the above-mentioned shifts with regard to these corrections for different scenarios. It is shown that probabilities of occurrence of the {\bf pbhs} under study with due regard for the given {\bf qgcs} are rising as compared to the semiclassical consideration. Besides, high-energy deformations of Friedmann Equations created on the basis of these corrections have been derived for different patterns. Conclusion contains the general remarks concerning the above-mentioned {\bf qgcs} for cosmological parameters and perturbations due to inflation; the steps for their investigation are outlined and the key problems of such a study are formulated.

Cancer theragnostics is a novel approach that combines diagnostic imaging and radionuclide therapy. It is based on the use of a pair of radiopharmaceuticals, one optimized for positron emission tomography imaging, through linkage to a proper radionuclide, and the other bearing a beta-emitter isotope that can induce significant damage to cancer cells. In recent years, the use of theragnostics in nuclear medicine clinical practice has increased considerably, and thus investigation has focused on the identification of novel radionuclides that can bind to molecular targets which are typically dysregulated in different cancers. The major advantages of the theragnostic approach include elimination of multi-step procedures, reduced adverse effects to normal tissues, early diagnosis, better predicting responses and personalized patient care. This review aims to discuss emerging theragnostic molecules that have been investigated in a series of human malignancies, including gliomas, thyroid cancer, neuroendocrine tumors, cholangiocarcinoma and prostate cancer, as well as potent and recently introduced molecular targets, like cell-surface receptors, kinases, and cell adhesion proteins. Furthermore, special reference has been made to copper radionuclides as theragnostic agents, and their radiopharmaceutical applications since they present promising alternatives to the well-studied gallium-68 and lutetium-177.

This study investigated a novel radioimmunotherapy strategy for targeting tumor angiogenesis. We developed a radiopharmaceutical complex by labeling an anti-adenosine triphosphate syn-thase (ATPS) monoclonal antibody (mAb) with the radioisotope 177Lu using DOTA as a chelating agent. 177Lu-DOTA-ATPS mAb demonstrated high labeling efficiency (99.0%) and stability in se-rum. MKN-45 cancer cells exhibited the highest cellular uptake, which could be specifically blocked by unlabeled ATPS mAb. In mice, 177Lu-DOTA-ATPS mAb accumulated significantly in tumors, with a tumor uptake of 16.0 ± 1.5%ID/g on day 7. 177Lu-DOTA-ATPS mAb treatment sig-nificantly reduced the viability of MKN-45 cells in a dose-dependent manner. In a xenograft tumor model, this radioimmunotherapy strategy led to substantial tumor growth inhibition (82.8%). Furthermore, combining 177Lu-DOTA-ATPS mAb with sunitinib, an anti-angiogenic drug, en-hanced the therapeutic efficacy of sunitinib in the mouse model. Our study successfully developed 177Lu-DOTA-ATPS mAb, a radioimmunotherapy agent targeting tumor blood vessels. This ap-proach demonstrates significant promise for inhibiting tumor growth, both as a single therapy and in combination with other anti-cancer drugs.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Gliomas are common primary central nervous system (CNS) tumours which are often very difficult to diagnose, stage and manage because of their heterogeneity and molecular aberrations. The notable hallmark of gliomas is integrated genome mutations and methylome that correlates with distinctive patterns of transcription that potentiates glioma heterogeneity, angiogenesis and ultimately poor prognosis. The World Health Organization (WHO) has decided to reclassify gliomas based on molecular markers rather than the traditional anatomical basis; use of Nuclear Medicine techniques e.g. SPECT/PET and Magnetic Resonance Imaging (MRI) techniques based on molecular markers is set to become the future gold standards. This has led to the investigations on potential for the use of non-invasive imaging techniques such as [68Ga]68Ga-RGD positron emission tomography (PET) to be utilised routinely in clinical practice based on angiogenic markers and also the potential to add information that may assist in drug-design and therapeutic decision making. This review aims to provide an overview of the basis of recent advances in glioma imaging using molecular targeting with positron emission tomography and SPECT imaging, as well as the role in patient management i.e. diagnosis, staging, recurrence detection etc.

The mining wastes generated during the last decades in the mining region of Pachuca-Real del Monte in Mexico, still contains silver values of interest. For this reason, the present work is a preliminary study of the leaching kinetics of silver contained in these residues, using as a leaching reagent the thiosemicarbazide-oxygen system, with the aim of proposing this leaching system as a less toxic alternative than cyaniding process. Previous the leaching process, representative samples were wholly characterized, finding 56 g of Ag and 0.6 g of Au per ton. For the kinetic study in the mentioned system, were evaluated the reagent concentration, temperature, partial pressure of oxygen, pH and stirring rate. According the experimental results found, it was observed that [CH₅N₃S] concentration showed a significant effect on the leaching rate, obtaining a reaction order of n = 0.93, in the range of 20 - 40 mol CH₅N₃S × m^-3, getting so a silver recovery up to 76.9%. The effect of temperature gave an activation energy of Ea = 45.55 KJ mol^-1, which was indicative of a chemical reaction control. Finally, partial pressure of oxygen has a notable effect on leaching rate, but pH and stirring rate have not apparent effect.

This paper reviews the requirements for the production, quality, and quality assurance of solid recovered fuels (SRF) that are increasingly used for the substitution of fossil fuels in the indus-trial utilities. The economical, technological and environmental aspects should be considered before using SRF as an alternative fuel. In general, the most important factors determining the commercial production of SRF referred to the calorific values and their available amounts adopted in the starting materials. Furthermore, the low-melting impurities and undesired constituents/elements, including chlorine, sulfur, potassium and sodium, may pose negative impacts on air pollutant emission and slagging & fouling in the process utilities. In this regard, the vent emitted from the industrial utilities must comply with the effluent standards of station-ary sources like particulate, sulfur oxides, nitrogen oxides, heavy metals (e.g., lead, cadmium, and mercury) and dioxins. For these reasons, this work will summarize the legal or regulatory requirements under development in Asian countries (i.e., Japan, South Korea, and Taiwan) and European Union (EU). Finally, the outlook of solid recovered fuel (SRF) in the waste manage-ment and industrial sectors will be addressed to echo the sustainable development goals (SDGs).

Non-woven jute (NWJ) produced from the carpet industry waste was oxidized by H2O2 or alkali treated by NaOH and compared with water-washed samples. Changes in the structure of the NWJ, tracked by XRD, showing that both chemical treatments disrupt hydrogen bond networks between cellulose Iβ chains of the NWЈ fibers. Thereafter, nano carbon nitride (nCN) was impregnated, using layer-by-layer technique, onto water washed jute sample (nCN-Jw), NaOH treated sample (nCN-Ja) and H2O2 treated sample (nCN-Jo). Analysis of the FTIR spectra of the impregnated samples, revealed that nCN anchors to the water washed NWЈ surface through hemicellulose and secondary hydroxyl groups of the cellulose. In the case of chemically treated samples nCN is preferentially bonded to the hydroxymethyl groups of cellulose. The stability and reusability of nCN-J samples were assessed by tracking the photocatalytic degradation of Acid Orange 7 (AO7) dye under simulated solar light irradiation. Results from up to ten consecutive photocatalytic cycles demonstrated varying degrees of effectiveness across different samples. nCN-Jo and nCN-Ja samples exhibited declining effectiveness over cycles, attributed to bond instability between CN and jute. In contrast, the nCN-Jw sample consistently maintained high degradation rates over ten cycles, with a dye removal percentage constantly above 90%.

CuO-ZnO-Al2O3 catalysts are designed for the low-temperature shift conversion in the process of hydrogen and ammonia synthesis gas production. The paper presents the results of research on recovery of copper and zinc from spent catalysts using pyrometallurgical and hydrometallurgical methods. Under reducing conditions, at high temperature, having appropriately selected the composition of the slag, more than 66% of copper in metallic form and about 70% of zinc in the form of ZnO can be extracted from this material. Hydrometallurgical processing of the catalysts was carried out using two leaching solutions: alkaline and acidic. Almost 62% of the zinc contained in the catalysts has been leached to the alkaline solution and about 98% of copper has been leached to the acidic solution. After the hydrometallurgical treatment of the catalysts, insoluble residue was also obtained in the form of pure ZnAl2O4. This compound can be reused to produce catalysts, or it can be processed under reducing conditions at high temperature to recover zinc. The recovery of zinc and copper from such a material is consistent with the policy of sustainable development and helps to reduce the environmental load of stored wastes.

With reference to electromagnetic interaction and Abdus Salam’s strong (nuclear) gravity, 1) Square root of ‘reciprocal’ of the strong coupling constant can be considered as the strength of nuclear elementary charge. 2) ‘Reciprocal’ of the strong coupling constant can be considered as the maximum strength of nuclear binding energy. 3) In deuteron, strength of nuclear binding energy is around unity and there exists no strong interaction in between neutron and proton. $G_s\cong 3.32688\times {10}^{28}{\mathrm{m}}^3{\mathrm{kg}}^{-1}{\sec }^{-2}$ being the nuclear gravitational constant, nuclear charge radius can be shown to be, $R_0\cong \frac{2G_s{m}_p}{c^2}\cong 1.24\mathrm{fm}.$ $e_s\cong \left(\frac{G_s{m}_p^2}{\hslash c}\right)e\cong 4.716785\times {10}^{-19}\mathrm{C}$ being the nuclear elementary charge, proton magnetic moment can be shown to be, ${\mu }_p\cong \frac{e_s\hslash }{2m_p}\cong \frac{e{G}_s{m}_p}{2c}\cong 1.48694\times {10}^{-26}\mathrm{J}{.\mathrm{T}}^{-1}.$ ${\alpha }_s\cong {\left(\frac{\hslash c}{G_s{m}_p^2}\right)}^2\cong 0.1153795$ being the strong coupling constant, strong interaction range can be shown to be proportional to $\exp \left(\frac{1}{{\alpha }_s^2}\right).$ Interesting points to be noted are: An increase in the value of ${\alpha }_s$ helps in decreasing the interaction range indicating a more strongly bound nuclear system. A decrease in the value of ${\alpha }_s$ helps in increasing the interaction range indicating a more weakly bound nuclear system. From $Z\cong 30$ onwards, close to stable mass numbers, nuclear binding energy can be addressed with, ${\left(B\right)}_{A_s}\cong Z\times \left\{\left(\frac{1}{{\alpha }_s}+1\right)+\sqrt{\sqrt{30\times 31}}\right\}\left(m_n-m_p\right)c^2\approx Z\times 19.66\mathrm{MeV}.$ With further study, magnitude of the Newtonian gravitational constant can be estimated with nuclear elementary physical constants. One sample relation is, $\left(\frac{G_N}{G_s}\right)\cong \frac{1}{2}{\left(\frac{m_e}{m_p}\right)}^{10}\left[\sqrt{\frac{G_F}{\hslash c}}/\left(\frac{\hslash }{m_{e}c}\right)\right]$ where $G_N$ represents the Newtonian gravitational constant and $G_F$ represents the Fermi’s weak coupling constant. Two interesting coincidences are, ${\left(m_p/m_e\right)}^{10}\cong \exp \left(1/{\alpha }_s^2\right)$ and $2G_s{m}_e/c^2\cong \sqrt{G_F/\hslash c}.$

Following the concept of strong interaction, theoretically, fusion of proton seems to increase the binding energy of final atom by 8.8 MeV. Due to Coulombic repulsion, asymmetry effect, pairing effect and other nuclear effects, final atom is forced to choose a little bit of binding energy less than 8.8 MeV and thus it is able to release left over binding energy in the form of internal kinetic energy or external thermal energy. Thus, in cold fusion, heat release to occur, binding energy difference of final atom and base atom seems to be less than 8.8 MeV. Qualitatively, energy released during cold fusion seems to be approximately equal to 8.8 MeV minus the difference of binding energy of final and base atoms. Based on this idea, under normal conditions, for the case of ₂He⁴, fusion of four protons can liberate (35.2-28.3)=6.9 MeV and it is 3.5 times less than the current estimates. Point to be understood is that, lesser the binding energy of final atom, higher the liberated thermal energy and vice versa. With a suitable catalyst and sufficient hydrogen under suitable pressure, if reactor’s temperature is maintained at (1000 to 1500) ⁰C, there seems a lot of scope for a chain reaction of cold fusion in which light isotopes transform to their next stage with increased proton number or mass number and liberate safe and clean heat energy continuously. By arranging 4 to 6 reactors and charging them periodically in tandem, required thermal energy can be produced continuously. In this new direction, by carefully selecting the base isotope and its corresponding catalyst, experiments can be conducted and ground reality of cold fusion can be understood at various temperature and pressure conditions.

Outliers seriously affect the accuracy in geometric model fitting. Previous works in coping with outliers involve threshold selection and scale estimation. However most scale estimators suppose the inlier distribution as a Gaussian model, which usually poorly meets the cases in geometric model fitting. Outliers, considered as the points with big residuals to all the true models, share common items with big values in quantized residual preferences, thus making the outliers gather away from the inliers in quantized residual preference space. In this paper we make use of this outlier consensus in quantized residual preference space by extending the usage of energy minimization to combine the model error and the spatial smoothness in quantized residual preference space for outlier detection. The energy minimization based outlier detection process follows an alternate sampling and labeling framework. After the outlier detection, an ordinary energy minimization method is employed to optimize the inlier labels, which also follows the framework of alternate sampling and labeling. The experimental results in this study show that the energy minimization based outlier detection method can detect most of the outliers in the data. Furthermore, the proposed energy minimization based inlier segmentation process segments the inliers into different models quite accurately. Overall, the performance of the proposed method is better than most of the state-of-the-art methods.

The atomic nucleus contains protons and neutrons surrounded by a structured electron cloud. Some combinations of protons and neutrons induce the nucleus to behave like a microscopic magnet, possessing a unique magnitude and orientation known as the nuclear magnetic moment (µ). When the numbers of protons and neutrons are both even then µ=0, but otherwise each nu-clide’s nuclear magnetic moment is unique. A second unique nuclear physical property relates to the nucleon binding energy (BE), which can be thought of as the energy between protons and neu-trons bound within the nucleus. The sequence of stable nuclides increases one nucleon at a time through 36Ar. The binding energy associated with the addition of each successive nucleon (∆BE) through this progression is unique. The hypothesis here is that the unique non-zero magnetic mo-ment and ∆ binding energy of each nuclide derive from its respective microscopic nuclear struc-ture, analogous to the way that the atomic physical properties of an element ultimately derive from its unique electron orbital structure. By extension, the identification of nuclear periodic pat-terns might eventually inform a theory of nuclear structure. The light, stable nuclides through 36Ar were arranged in ascending order according to atomic mass, and their nuclear magnetic mo-ments and binding energies were evaluated for periodic patterns. Fixed-period lengths from 4 through 18 nuclides per period were considered. These fixed periods, each of equal length, were stacked one upon the other and analyzed for vertical trends. The best evidence of periodicity in both µ and ∆BE converges precisely at the fixed 12-nuclide period. Implications for nuclear structure are discussed.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

Mushroom production in Poland is an important and dynamically developing element of diverse agriculture. Mushroom spent compost (MSC) is major waste generated during production, i.e., MSC: mushrooms is ~5:1. To date, the main use of MSC is soil application as organic fertilizer. To date, several methods of MSC treatment have been researched and developed including production of compost, bioethanol, biogas, enzyme lactase, xylo-saccharides, and hydrogen. Torrefaction may be considered a novel approach for biomass valorization. Thus, we are pioneering the potential use of MSC valorization via torrefaction. We explored valorizing the waste biomass of MSC via thermal treatment – torrefaction (‘roasting’) to produce biochar with improved fuel properties. Here for the first time, we examined and summarized the MSC torrefaction thermogravimetric analyses, fuel properties data of raw biomass of MSC and biochars generated from MSC via torrefaction. The effects of torrefaction temperature (200~300 °C), process time (20~60 min), on fuel properties of the resulting biochars were summarized. The dataset contains results of thermogravimetric analysis (TGA) as well as proximate analyses of MSC and generated biochars. The presented data are useful in determining MSC torrefaction reaction kinetics, activation energy and to further techno-economical modeling of the feasibility of MSC valorization via torrefaction. MSC torrefaction could be exploited as part of valorization resulting from a synergy between an intensive mushroom production with the efficient production of high-quality renewable fuel.

A valorization process of spent coffee grounds (SCG) was studied. Thus, a two-stage process, a stage of extraction of the polyphenols and a stage of obtaining activated carbon (AC) by a carbonization process, was performed. The extraction was carried out with a hydro-alcoholic solution in a pressure reactor, modifying time and temperature. To optimize the extraction of polyphenols, a two-level factorial design with three replications at the central values was used. The best results were obtained by performing the extraction at 80 °C during 30 min, using a mixture of EtOH:H2O 1:1 (v/v) as extraction solution. Caffeine and chlorogenic acid were the most abundant compounds in the analyzed extracts, ranging from 0.09 to 4.8 mg∙g^-1 and 0.06 to 9.7 mg∙g^-1, respectively. The precursor obtained in the extraction stage were transformed into AC. An experimental design was realized in order to analyze the influence of different variables in the AC obtained process (reaction time and amount of potassium hydroxide used). Actived carbons with BET specific surface (SBET) comprised between 1600 m^2∙g^-1 and 2330 m²∙g^-1 had a microporous surface. Under the optimum conditions, the obtained AC presented a maximum adsorption capacity of methylene blue (qm) between 411 mg∙g^-1 and 813 mg∙g^-1.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FR). Significant amounts of FR are usually required to effectively affect the polymer burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC) and pentaerythritol (PER) and its composites containing additionally short basalt fibers (BF). Composites manufactured by twin-screw extrusion were subjected to four reprocessing cycles by injection molding, comprehensively analyzing structural, mechanical, and fire behavior changes in each cycle. The obtained results confirmed the safety of using the proposed flame-retardant system for polyamide, processed under the recommended process parameters, without the risk of significant changes in the structure despite the partial increase in flammability caused mainly by the degradation of the polymer.

Hybrid electric vehicles (HEVs) are perceived as a first step towards the future of sustainable transport. Of course, battery electric vehicles (EVs) are currently ideal for what is wanted to stand for transport in the future. The lack of infrastructure for these vehicles makes many potential users choose hybrid vehicles in these conditions. This paper analyzes the influence of the engine and electric motor of hybrid vehicles on their performances. Three engines with slightly different power and close characteristics were considered for configured models. Also, two electric motors with very different power but having a very close maximum continuous torque have been used in models. One is an induction motor, and the other is a permanent magnet synchronous motor. ADVISOR software has been used for vehicles configuration and simulation. Series and parallel hybrid vehicles have been considered. The main dynamic performances and the fuel consumption in two driving cycles were compared for the configured models. Three conventional models with the same engines used in HEVs have also been simulated for reference. The results highlight that in the case of HEVs, the choice of combination engine/electric motor is crucial in obtaining the best report between dynamic performances and low fuel consumption, and implicitly a low negative impact on the environment.

The peptidyl-prolyl isomerases of the cyclophilin type are distributed throughout human cells, including eight found solely in the nucleus. Nuclear cyclophilins are involved in complexes that regulate chromatin modification, transcription, and pre-mRNA splicing. This review collects what is known about the eight human nuclear cyclophilins: PPIH, PPIE, PPIL1, PPIL2, PPIL3, PPIG, CWC27, and PPWD1. Each “spliceophilin” is evaluated in relation to the spliceosomal complex in which it has been studied, and current work studying the biological roles of these cyclophilins in the nucleus are discussed. All eight of the human splicing complexes available in the PDB are analyzed from the viewpoint of the human spliceophilins. Future directions in structural and cellular biology, and the importance of developing spliceophilin-specific inhibitors, are considered.

Spent batteries recycling is an important way to obtain low-cost graphite. Nevertheless, the obtaining of crystalline graphite with a rather low density of defects is required for many applications. In the present work, high-quality graphites have been obtained from different kinds of spent batteries. Black masses from spent alkaline batteries (batteries black masses, BBM), and lithium-ion batteries from smartphones (smartphone black masses, SBM) and electric and/or hybrid vehicles (lithium-ion black masses, LBM) were used as starting materials. A hydrometallurgical process was then used to obtain recycled graphites by acidic leaching. Different leaching conditions were used depending on the type of the initial black mass. The final solids were characterized by a wide set of complementary techniques.

Telomeres in epithelial tumours are usually maintained by telomerase, however, in the breast cancer MDA-MB-231 cell line, polyploid cells, induced by doxorubicin (DOX) were found, after mitotic slippage, transiently shifting to recombinatory alternative telomere lengthening (ALT) in PML bodies (APBs). The involvement of the meiotic recombination proteins was evidenced here by juxta-co-localisation of SPO11, DMC1 and RAD51/γH2AX with APBs in these and melanoma SkMel28-DOX-treated cells. Using sublethal doses of DOX we also observed the formation of the PML dimeric rod tandems linking γH2AX/TRF2 foci into ribbons discontinuously inserted into lamin B1 and circumventing cell nuclei. Next, we link these PML-lamin B1 insertions and peripheral rotation of the tandemly linked telomere repeats with the mobility of the nuclear envelope limited chromatin sheets (ELCS). ELCSs comprise two layers of the criss-crossed ~30 nm granules derived from surface heterochromatin (epichromatin) which contains telomere repeats enriched in GpC, PML, and ALU. ELCS protrude, circumvent, loop, split, fuse, and rejoin polyploid cell nuclei. We propose this gear-wheel-like turnover of telomere repeats to be used for the homology search. Interstitial and end-telomere repeats flanked by fragile ALU-Z flipons become recognised by SPO11 nuclease, attract TRF2, PML, and meiotic recombinases. Subsequently, they perform ALT recombining subtelomeres and telomeres or undergo non-homologous end-joining and chromosome rearrangements with ELCS. This mechanism increases the chance of cell survival and may be involved in chromothripsis.

Nuclear fusion is essential for the sexual reproduction of various organisms, including plants, animals, and fungi. During the life cycle of flowering plants, nuclear fusion occurs three times: once during female gametogenesis and twice during double fertilization, when two sperm cells fertilize the egg and the central cell. Haploid nuclei migrate in an actin filament-dependent manner to become in close contact, then two nuclei fuse. The nuclear fusion process in plant reproduction is achieved by the sequential nuclear membrane fusion events. Recent molecular genetic analyses using Arabidopsis thaliana showed the conservation of nuclear membrane fusion machinery between plants and the budding yeast Saccharomyces cerevisiae. These include the heat shock protein 70 in the endoplasmic reticulum and conserved nuclear membrane proteins. Analyses of A. thaliana mutants of these components show that completion of the sperm nuclear fusion at fertilization is essential for proper embryo and endosperm development.

Coffee is regarded as the highly consumed beverage throughout the world and has established a key spot in the world economy as an important commodity for trading. In general, they are produced by brewing their roasted and ground beans, which release aromatic coffee; as well as produce an equivalent amount of spent coffee grounds (SCG). Previously, they were discarded as wastes or used as natural pest repellent or garden fertilizer; however, in recent times, are valorized into biofuels owing to their high calorific value. In fact, SCG briquettes have gained wide attention for supplying energy renewably, especially to the rising energy demand; and also have been identified as an effective measure to reduce their pollution. With this in mind, this present chapter focuses on reviewing the availability and chemistry involved in these SCG wastes, pre-treatments and preparations required for their briquetting, compacting techniques followed, and fuel characteristics of their briquettes, from various available works of literature. Here, their availability showcases the amount of SCG wastes generated with respect to time and consumption, wherein understanding their chemistry helps in deciding the pre-treatments necessary for their briquetting. Meanwhile, preparation techniques briefs about the necessary pre-treatments undertaken before compaction by different researchers; and the fuel characteristics define the physicochemical and mechanical properties of their briquettes, developed using various compaction methods. Besides, combustion behaviors of these briquettes are explained in terms of their burning characteristics and emission levels, as reported in literatures; which help in deciding their suitability as a replacement for existing fossil coal. Eventually, all the reported data were in accordance with their permissible standards and suggested these SCG as a highly renewable solid biofuel.

Fumaric acid is a chemical building block with many applications, namely in the polymer industry. The fermentative production of fumaric acid from renewable feedstock is a promising and sustainable alternative to petroleum-based chemical synthesis. The use of existing industrial side-streams as raw-material within biorefineries potentially enable production costs competitive against current chemical processes, while preventing the use of refined sugars competing with food and feed uses and avoiding purposely grow crops requiring large areas of arable land. However, most industrial side streams contain a diversity of molecules that will add complexity to the purification of fumaric acid from the fermentation broth. A process for the recovery and purification of fumaric acid from complex fermentation medium containing spent sulfite liquor (SSL) as carbon source was developed and is herein described. A simple two-stage precipitation procedure involving separation unit operations, pH and temperature manipulation and polishing through the removal of contaminants with activated carbon allowed the recovery of fumaric acid with 68.3% recovery yield with specifications meeting the requirements of the polymer industry. Further, process integration opportunities were implemented that allowed minimizing the generation of waste streams containing fumaric acid which enabled increasing the yield to 81.4% while keeping the product specifications.

Multi-modal Motion-assisted Memory Desensitization and Reprocessing Therapy (3MDR), an interactive, virtual-reality assisted, exposure-based intervention for PTSD, has shown promising results for treatment-resistant Posttraumatic Stress Disorder (TR-PTSD) among military members (MMs) and Veterans in Randomized Controlled Trials. Previous research has suggested that emotional regulation (ER) and emotional dysregulation (ED) may be factors which are correlated with symptom severity and maintenance of TR-PTSD. This embedded mixed-methods pilot study (n=9) sought to explore the impact of 3MDR on ER and ED of MMs and Veterans. Difficulties in Emotional Regulation Scale (DERS-18) data was collected at baseline, prior to each session, and at 1 week, 1 month and 3 months post-intervention and analyzed using a Wilcoxon signed-ranks test. Qualitative data collected from sessions, debriefs, and follow-up interviews were transcribed and descriptively analyzed. Results demonstrated statistically significant decreases in DERS-18 scores from pre-intervention to post-intervention at each timepoint. Qualitatively, participants perceived improvements in ER within specified DERS-18 domains. We describe how 3MDR’s unique and novel approach may address ED through cognitive-motor stimulation, narration, divergent thinking, reappraisal of aversive stimuli, dual-task processing, and reconsolidation of traumatic memories. Further investigation is underway to better understand the underlying neurobiological mechanisms by which 3MDR addresses ER and PTSD.

We propose novel spectrometer designs that aim to enhance the measured spectral range 1 of ions on a finite-sized detector. In contrast to the traditional devices that use uniform magnetic 2 field, in which the deflection of particles increases inversely proportional to their momentum, in a 3 gradient magnetic field, the deflection of particles will be decreased due to the reduction of the 4 magnetic field along their propagation. Low energy ions are particularly impacted, as they are 5 deflected less and are more likely to reach the detector compared to being driven out of it while 6 using a uniform magnetic field. By the means of a gradient magnetic field, the nonlinear dispersion 7 of ions in a homogeneous magnetic field can approach a nearly linear dispersion. Nonetheless, 8 the dispersion of low energy ions in a homogeneous magnetic field remains unnecessarily high. 9 In this article, we explore linear, quadratic, and higher-order field profiles in comparison to the 10 homogeneous field case. We discuss the employed methodology and present simulation results of 11 the spectrometer with an extended ion spectral range, focusing on the minimum detectable energy 12 (energy dynamic range) and energy resolution

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

Annually, the oak forests of the Zagros Mountain chains, in western Iran and northeastern Iraq, face recurring challenges posed by forest fires, particularly in the Kurdo-Zagrosian forests situated in western Iran and northeastern Iraq. Assessing fire susceptibility relies significantly on vegetation condition. Integrating in situ data, Remote Sensing (RS) data, alongside the integration of Geographical Information Systems (GIS), presents a cost-effective and precise approach to capturing environmental conditions before, during, and after fire events, minimizing the need for extensive fieldwork. This study refines and applies the Zagros Grass Index (ZGI), a local vegetation index tailored to discern between grass-covered surfaces from tree canopies in Zagros forests, identifying the grass masses as the most flammable fuel type. Utilizing Moderate Resolution Imaging Spectroradiometer (MODIS) Normalized Difference Vegetation Index (NDVI) product as input, from 2013 to 2022, the ZGI aims to mitigate the influence of tree canopies, isolating NDVI values solely attributable to grass cover. By incorporating phenological characteristics of forest trees and grass species, the ZGI outperforms NDVI in mapping grass-covered areas that are crucial for fire susceptibility assessment in the study region. Results demonstrate a strong overlap between ZGI-based maps and recorded fire occurrences, validating the efficacy of the index in fire susceptibility estimation.

In order to study the movement characteristics of fuel in the fuel tank during aircraft maneuvering, this paper conducts numerical simulations of a typical wing fuel tank using the finite point set method based on certain boundary conditions and excitation. The results show that the finite point set method can capture the complex phenomena of fuel free surface fluctuations, surging, rolling and breaking, as well as the change in center of gravity caused by fuel movement. Under aircraft acceleration and pitch angle excitation, fuel will generate sustained impact pressure on the fuel tank wall. The velocity attenuation of fuel flowing through the baffle communication hole is fast, and the flow resistance and energy dissipation of the communication hole buffer the impact of fuel on the fuel tank wall.

The design and integration of intelligent energy management systems in hybrid Electric Vehicle (EV) charging stations, leveraging Industry 4.0 and renewable energy sources, is crucial for advancing sustainability, efficiency, and technological development. This paper introduces a pioneering hybrid EV charging station that employs hybrid power sources, combining photovoltaic panels, a battery, and a fuel cell, each operating at 240V and 14A. Utilizing wireless power transfer technology, the system comprises five integral blocks: a power source, a boost converter, a High-Frequency (HF) inverter, transfer coils, and EV batteries. The optimization process involves two key stages: i) maximum power point tracking optimization of the boost converter, ensuring maximum power generation by varying the duty cycle between 10% and 90%, and ii) the HF phase employing a class-ϕ2 inverter at 30 MHz, synchronized with the resonant frequency of wireless power transfer coils. Control is executed through a digital signal processor card utilizing zero-voltage switching for efficient operations. This design enhances sustainability in EV charging solutions by optimizing power transfer through the use of hybrid sources.

This study investigates the influence of pyrolysis temperature on the main properties of BSG (brewer's spent grain) biochar and evaluates its suitability as an energy vector and as a substrate component. Pyrolysis tests were carried out at 673, 773, and 873 K. Bioenergy indexes were calculated for BSG and its biochar, and germination tests were carried out to obtain lentil sprouts. The results showed that the BSG biochar obtained at the lowest temperature biochar presented the best performance for use as biofuel. Regarding the germination tests, the different biochars were applied at 4 doses, and the evaluated parameters such as germination percentage, germination rate, mean germination time, and seed vigor were strongly influenced by the biochar addition. The biochar at 773 K added at a dose of 5% doubled the values of mean germination time, seed vigor, and time for 50% of the seeds to emerge compared to the control, constituted only with distilled water. The sustainable BSG valorization through pyrolysis reduces waste and contributes to circular economy practices by transforming industrial by-products into valuable resources for energy and agriculture. This approach highlights the importance of sustainability in reducing the environmental impact of industrial waste and promoting renewable energy sources.

In bovine embryos, microRNA (miRNA) expression has been profiled at each stage of early development in-vitro. miRNAomic analysis of spent media has the potential to reveal characteristics of embryo health, however, applications are limited without categorizing miRNA profiles by embryo quality. Time-lapse imaging has shown the timing of embryo development in-vitro may be indicative of their developmental potential. The aim of the study was to profile miRNAs in the spent media of slow and fast-growing bovine embryos throughout the pre-implantation period. Bovine cumulus-oocyte-complexes were aspirated from ovaries, fertilized, and cultured to blastocyst stage of development. At 2-cell, 8-cell, and blastocyst stage, each microdrop of 30 presumptive-zygotes were classified as slow or fast-growing based on the percentage of embryos that had reached the desired morphological stage. Following hybridization on a GeneChip miRNA 4.0 array, comparative analysis was conducted between spent media of slow and fast-growing embryos. In total, 34 differentially expressed miRNAs were identified between the comparison groups, with 14 of the miRNAs detected in the 2-cell samples, 7 miRNAs detected in the 8-cell samples, and 12 miRNAs detected in the blastocyst samples. The results demonstrate distinct miRNAs populations can be identified between slow and fast-growing embryos, highlighting novel biomarkers of developmental potential at each stage of pre-implantation development.

Spent mushroom compost (SMC) substrates are commonly used as growth media for greenhouse crops and horticulture production. This study aimed to investigate the responses of physiochemical soil properties, enzyme activities, and microbial community compositions to different cultivation durations and SMC soil treatments on tomatoes (Solanum lycopersicum L.) grown in plastic greenhouses on the Loess Plateau, China. The experiment included treatments: Two control treatments of non-planting SMC substrates (Sub CK) and continuous mono-cropping soil (Soil CK), and SMC substrate and the surrounding soil after planting at 1, 3, and 7 years. The results revealed that the SMC substrates had higher contents of major nutrients (e.g., total N and total P) than the surrounding soil treatments. The physicochemical soil properties and soil enzyme activities of the SMC substrates were significantly decreased with longer cultivation duration. Microbial alpha-diversity was higher in the SMC substrates regardless of cultivation duration than the control treatment (soil CK and substrate CK). Interestingly, following several years of tomato cultivation, the compositions of bacterial communities had more similarities with fungal communities in both the SMC substrates and surrounding soils. It was observed that many beneficial microbes, such as bacteria of the Deinococcus-Thermus, Halanaerobiaeota, and Nitrospirae phyla, and the fungi of the Basidiomycota, Mortierellomycota, and Chytridiomycota phyla were enriched in the SMC substrates. The pathogenic bacterial genus Sphingomonas and fungal genus Fusarium were abundant in the Soil CK treatment, while the potentially beneficial bacterial genera Saccharimonadales, Gaiella, Bacillus, and fungal genera Thermomyces, Kernia, and Mortierella were abundant in both the SMC substrate and surrounding soil. This study demonstrated that agro-based SMC substrates were a suitable growth media for a new grooved cultivation system.

Electricity load forecasting is a crucial undertaking within all the deregulated markets globally. In contemporary times, the transition from conventional electricity grids to Smart Grids constitutes an area where extensive research is conducted on a global scale. Among the research challenges, the investigation of Deep Transfer Learning (DTL) in the field of electricity load forecasting represents a fundamental effort that imparts generality to Artificial Intelligence applications, due to new capabilities, such as knowledge transfer and computational power reduction. In this paper a comprehensive study is conducted for day-ahead electricity load forecasting. For this purpose, three Sequence-to-Sequence (Seq2seq) Deep Learning (DL) models are used, namely the Multilayer Perceptron (MLP), the Convolutional Neural Network (CNN) and the Ensemble Learning Model (ELM), which is consisted of the weighted combination of the outputs of MLP and CNN models. Also, the study focuses on the development of different forecasting strategies based on DTL and emphasizing the way the datasets are trained and fine-tuning for higher forecasting accuracy. In order to implement the forecasting strategies using Deep Learning models, load datasets from three Greek islands, Rhodes, Lesvos, and Chios, are used. The main purpose is to apply DTL for day-ahead predictions (1-24 hours) for each month of the year for Chios dataset after training and fine-tuning the models using the datasets of the three islands in various combinations. After several trials, four DTL strategies are illustrated. In the first strategy (DTL Case 1), each of the three DL models is trained using only Lesvos dataset, while fine-tuning is performed on the dataset of Chios island, in order to create day-ahead predictions for Chios load. In the second strategy (DTL Case 2), data from both Lesvos and Rhodes concurrently are used for the DL model training period, and fine-tuning is performed on the data from Chios. The third DTL strategy (DTL Case 3) contains the training of the DL models using Lesvos dataset, and the testing period performed directly on the Chios dataset without fine-tuning. The fourth strategy is a Multi-task Deep Learning (MTDL) approach, which has been extensively studied in recent years. In MTDL, the three DL models are trained simultaneously on all three datasets and the final predictions are made on the unknown part of the dataset of Chios. In this paper, we explore the performance of DTL and compare the results with those produced with MTDL. The results demonstrated that DTL can be applied with high efficiency for day-ahead load forecasting. Specifically, the two cases with fine-tuning (DTL Case 1 and 2) outperformed MTDL in terms of load prediction accuracy. Regarding the DL models, all three exhibit very high prediction accuracy, especially in the two cases with fine-tuning. The ELM excels compared to the single models. More specifically, for conducting day-ahead predictions, it has been concluded that the MLP model presents best monthly forecasts with a MAPE of 6.24% and 6.01% for the first two cases, the CNN model presents best monthly forecasts with a MAPE of 5.57% and 5.60% respectively and the ELM model achieves best monthly forecasts with a MAPE of 5.29% and 5.31%, respectively, indicating the very high accuracy it can achieve.

With reference to our earlier published views on large nuclear gravitational constant , nuclear elementary charge and strong coupling constant , in this paper, we present simple relations for nuclear stability range, binding energy of isotopes and magic proton numbers.

The beer industry is a major producer of solid waste globally, primarily in the form of brewer’s spent grains (BSG), which due to its low value has historically been diverted to livestock as feed or to landfills as waste. Its high moisture content and chemical composition positions BSG as an ideal candidate for further processing with microbial fermentation, and recent research has focused on filamentous fungi and the ability of some species therein to degrade the predominant recalcitrant cellulolignin components of BSG to produce valuable compounds. Many species have been investigated to biovalorize this waste stream, including those in the genuses Aspergillus, Pennicillium, Rhyzopus, and Trichoderma, which have been used to produce a wide array of highly valuable enzymes and other functional compounds, and to increase the nutritional value of BSG as an animal feed. This review of recent developments in the application of filamentous fungi for the valorization of BSG will discuss the biochemical makeup of BSG, the biological mechanisms underlying fungi’s primacy to this application, and the current applications of fungi in this realm. As the majority of these studies are at lab-scale, the challenges to scale-up and more widespread application and will be discussed as well.

This paper describes the physico-chemical study of the adsorption of dysprosium (Dy³⁺) in aqueous solution onto two types of activated carbons synthesized from spent coffee ground. KOH activated carbon is a microporous material with a specific BET surface area of 2330 m²·g^-1 and pores with a diameter of 3.2 nm. Carbon activated with water vapor and N₂ is a solid mesoporous, with pores of 5.7 nm in diameter and a specific surface of 982 m²·g^-1. A significant dependence of the adsorption capacity on the solution pH was found, while it does not depend significantly neither on the dysprosium concentration nor on the temperature. A maximum adsorption capacity of 31.26 mg·g^-1 and 33.52 mg·g^-1 for the chemically and physically activated carbons, respectively, were found. In both cases, the results obtained from adsorption isotherms and kinetic study were better fit to a Langmuir model and a pseudo-second-order kinetics. In addition, thermodynamic results indicate that dysprosium adsorption onto both activated carbons is an exothermic, spontaneous and favorable process.

Fast Field-Cycling (FFC) Nuclear Magnetic Resonance (NMR) relaxometry is a powerful non-destructive magnetic resonance technique that enables, among other things, the investigation of slow molecular dynamics at low magnetic field intensities. FFC-NMR relaxometry measurements provide insight into molecular motion across various timescales within a single experiment. This study focuses on a \textit{model-free} approach, representing the NMRD profile $R_1$ as a linear combination of Lorentzian functions, thereby addressing the challenges of fitting data within an ill-conditioned linear least-squares framework. Tackling this problem, we present a comprehensive review and experimental validation of three regularization approaches to implement the model-free approach to analysing NMRD profiles. These include: (1) \nameUpe, utilizing locally adapted $L_2$ regularization; (2) \nameL, based on $L_1$ penalties; and (3) a hybrid approach combining locally adapted $L_2$ and global $L_1$ penalties. Each method's regularization parameters are determined automatically, according to the Balancing and Uniform Penalty principles. % Our contributions include the implementation and experimental validation of the \nameUpe{} and \nameUp{} algorithms, and the development of a "dispersion analysis" technique to assess the existence range of the estimated parameters. The objective of this work is to delineate the variance in fit quality and correlation time distribution yielded by each algorithm, thus broadening the set of software tools for the analysis of sample structures in FFC-NMR studies. The findings underline the efficacy and applicability of these algorithms in the analysis of NMRD profiles from samples representing different potential scenarios. 1

I review the solution of QCD in two spacetime dimensions. Following the analysis of Baluni, for a single flavor the model can be analyzed using Abelian bosonization. The theory can be analyzed in strong coupling, when the quarks are much lighter than the gauge coupling. In this limit, the theory is given by a Luttinger liquid.

Nuclear lamins are type V intermediate filament proteins that form a filamentous meshwork beneath the inner nuclear membrane. Additionally, a sub-population of A-type and B-type lamins is localized in the nuclear interior. The nuclear lamina protects the nucleus from mechanical stress and mediates nucleo-cytoskeletal coupling. Lamins form a scaffold that partially tethers chromatin at the nuclear envelope. The nuclear lamina also stabilizes protein-protein interactions involved in gene regulation and DNA repair. The lamin-based protein sub-complexes are implicated in both nuclear and cytoskeletal organization, the mechanical stability of the nucleus, genome organization, transcriptional regulation, genome stability, and cellular differentiation. Here we review recent research in the field of nuclear lamins and their role in modulating various nuclear processes and their impact on cell function.

With reference to Planck scale Hubble parameter, super luminal expansion speeds, super luminal rotation speeds, Mach’s principle and Holographic principle, we review the current cosmological observations with eight simple assumptions. By understanding Yuri N. Obukhov and V.A. Korotky proposed cosmic rotational effects of polarization of radiation due to massive bodies, to some extent cosmic rotation can be deep-rooted in an observational approach and the ratio of current angular velocity and Hubble parameter can be estimated. It is possible to show that, at H₀ =70 km/sec/Mpc, current cosmic temperature, age, radius, mass, mass density are 2.721 K, 4.41x10¹⁷ sec, 90 billion light years, 1.14654x10⁵⁴ kg, 0.0482 times the current critical density respectively. Clearly speaking, current universe seems to constitute 267 Hubble spheres. Important point to be noted is that, current rotational kinetic energy is 0.6667 times the current critical energy. Based on the estimated current mass density and current rotational kinetic energy, current cosmic dark matter density can be shown to be 0.2851 times the current critical density. These numerical coincidences cast serious doubt on the on the real existence of currently believed ‘dark energy’. Initial and current expansion speeds are 3x10⁸ m/sec and 3.56x10⁹ m/sec respectively. With increasing cosmic age and increasing cosmic expansion speed, current universe is expanding with a speed of 11.885c. By knowing the time to time future cosmic temperatures, future Hubble parameters and corresponding future cosmic expansion speeds can be estimated and thus future expansion speed can be understood. Starting from ‘speed of light’, our model assumes a continuous increase in expansion speed and attains a current radius of 90 billion light years (without inflationary concepts) and casts a serious doubt on the actuality of currently believed ‘inflation’.

The construction of optimized biological fuel cells requires a cathode which combines the longevity of a microbial catalyst with the power density of an enzymatic catalyst. Laccase secreting fungi were grown directly on the cathode of a biological fuel cell to facilitate the exchange of inactive enzymes with active enzymes with the goal of extending the lifetime of laccase cathodes. Additionally, a functionally graded coating was developed to increase enzyme loading at the cathode. Directly incorporating the laccase producing fungus at the cathode extends the operational lifetime of laccase cathodes while eliminating the need for frequent replenishment of the electrolyte. Additionally, the hybrid microbial-enzymatic cathode addresses the issue of enzyme inactivation by using the natural ability of fungi to exchange inactive laccases at the cathode with active laccases. Finally, enzyme adsorption was increased through the use of a functionally graded coating containing an optimized ratio of titanium dioxide nanoparticles and single walled carbon nanotubes. The hybrid microbial-enzymatic fuel cell combines the higher power density of enzymatic fuel cells with the longevity of microbial fuel cells and demonstrates the feasibility of a self-regenerating fuel cell in which inactive laccases are continuously exchanged with active laccases.

Nuclear energy, along with renewable and alternative energy sources, is a crucial green energy source. However, the existing literature often overlooks the role of nuclear energy in achieving sustainable development goals. This study analyzes the impact of green technological innovation, nuclear energy consumption, and trade openness on environmental quality in the US, which consumed the most nuclear energy from 1990 to 2019. The ARDL bounds testing approach was applied for its effectiveness in smaller samples, suitable for the data set used in this study, to determine cointegration relationships. Additionally, the Toda-Yamamoto causality test was employed to explore causal links without requiring series stationarity or cointegration. The ARDL cointegration results indicate a significant long-term relationship between CO2 emissions, green technological innovation, nuclear energy consumption, and trade openness. The results suggest that promoting green technological innovation and nuclear energy (although this effect is less certain) can be effective strategies for reducing CO2 emissions, while the impact of trade openness requires careful consideration due to its potential to increase emissions. Green technological innovation has a significant unidirectional causal effect on CO2 emissions. These results will help policymakers design policies to achieve sustainable environmental goals in the US economy.