The performance of a normal-strength SHCC under impact loading was studied using the results obtained from a split Hopkinson tension bar (SHTB). The focus of the investigation is to explain the mechanisms behind the peculiar rate-dependent behavior of SHCC under tensile loading. With the help of frames obtained by high-speed cameras and the subsequent Digital Image Correlation (DIC) analysis, the stress-strain relation of the SHCC obtained in SHTB was analyzed. The investigation of the composite’s behavior was supported by constituent-level experiments on the non-reinforced matrix of the SHCC and on the fiber-matrix bond. In the case of the constituent matrix, the well-known apparent increase in the tensile strength of the cement-based matrix and its influence on the behavior of SHCC was studied. For this purpose, experiments on the SHCC specimens with different geometries were performed in the SHTB. The results obtained from these experiments and those obtained by DIC show that commonly used analytical models, in which the specimen is assumed elastic, cannot capture the effects of structural inertia on the results. Thus, an alternative novel method based on the results of DIC has been used to explain and quantify the contribution of structural inertia. The rate-dependent behavior of the fiber-matrix bond was studied by performing high-speed single fiber pullout tests in a miniaturized split Hopkinson tension bar. This novel experimental technique enabled explanation of the rate-dependent bridging action of the fibers in SHCC. Based on the results, the enhanced behavior of SHCC under impact loading is explained.

Giant unilamellar vesicles (GUVs) are membrane model used to study membrane properties. Electroformation is one of the methods used to produce GUVs. During electroformation protocol dry lipid film is formed. Drying of the lipid film induce Cholesterol (Chol) demixing artifact, in which Chol forms anhydrous crystals, where these crystals does not participate in formation of vesicles. This leads to a lower Chol concentration in the vesicle bilayers compared to the Chol concentration in the initial lipid solution. To address this problem, we propose novel electroformation protocol that includes rapid solvent exchange, plasma cleaning and spin-coating methods to produce GUVs. We tested the protocol focusing on vesicles with high Chol content using different spin-coating durations and vesicle types deposition. Additionally, we compared the novel protocol using completely dry lipid film. The optimal spin-coating duration for vesicles made out of phosphatidylcholine/Chol mixture was 30 s. Mulitlamellar vesicles (MLVs), large unilamellar vesicles (LUVs) obtained by extrusion of MLVs through 100 nm membrane pores and LUVs obtained by extrusion of previously obtained LUVs through 50 nm membrane pores were deposited on electrode for 1.5/1 Chol/phosphatidylcholine lipid mixture and the results were compared. Electroformation using all three deposited vesicle types gave a high GUVs yield, but deposition of LUVs obtained by extrusion of MLVs through 100 nm membrane pores gave the most reproducible results. Using deposition of these LUVs, we produced GUVs with high yield for 6 different Chol concentrations (from 0 % to 71.4%). Using protocol that includes dry lipid film GUVs yield was lower and Chol demixing artifact was induced, proving that the lipid film should never undergo drying when Chol content is high.

Background: Helicobacter pylori (H. pylori) is a prevalent bacterial pathogen implicated in various gastroduodenal diseases, including chronic gastritis, peptic ulcer disease, and gastric cancer. The COVID-19 pandemic has significantly influenced antibiotic prescription practices, potentially exacerbating antibiotic resistance in H. pylori. Objective: This study aims to investigate antibiotic prescription during COVID-19 pandemic in Croatia and its possible impact on H. pylori antibiotic resistance, with a focus on Croatia. Methods: A comprehensive literature search was conducted to identify relevant studies from March 2020 to June 2024. The search strategy included terms related to COVID-19, antibiotic prescription, and Croatia. Studies were selected based on predefined eligibility criteria, focusing on observational research addressing antibiotic use during the pandemic. Results: The COVID-19 pandemic leads to significant fluctuations in community antibiotic consumption within the European Union/European Economic Area. In Croatia, antibiotic use in 2022 surpassed 2019 levels, driven by increased consumption of macrolides and other antibiotics. This surge, influenced by early pandemic treatment claims and penicillin shortages, contributed to rising antibiotic resistance in H. pylori. Resistance rates to clarithromycin and levofloxacin were notably high, driven by mutations in the 23S rRNA, gyrA, and gyrB genes. Discussion: The increased antibiotic use during the COVID-19 pandemic has highly likely complicated H. pylori eradication efforts, highlighting the necessity of judicious antibiotic use and robust antimicrobial stewardship. The pandemic underscored the need for new therapeutic strategies, optimized eradication regimens, and advanced diagnostic methods to manage bacterial infections effectively. Conclusions: The COVID-19 pandemic has significantly impacted antibiotic use and resistance patterns, posing new challenges for H. pylori eradication. Addressing these challenges requires a multifaceted approach, including the development of new drugs and advanced diagnostics, coupled with sustained efforts in antimicrobial stewardship to combat emerging resistance threats.

Here we report a comparative study of the pyhtochemical profile and a biological activity of the two onion extracts, namely A. cepa L. and A. × cornutum (Clementi ex Visiani 1842). Identification of flavonoids and anthocyanins and their individual quantities were determined by high performance liquid chromatography (HPLC). The potency of both extracts to scavenge free radicals was determined by DPPH (2,2'-diphenyl-1-picrylhydrazyl) radical-scavenging activity and oxygen radical absorbance capacity (ORAC) methods. DNA protective role was further tested by single-cell gel electrophoresis (COMET) assay and by Fenton’s reagent causing double strand brakes on pUC19 plasmid. In the presence of both extracts, a significant decrease in the DNA damage was observed, which indicates a protective role of A. cepa and A. × cornutum on the DNA strand brakes. Additionally, cytotoxicity was tested on glioblastoma and breast cancer cell lines. The results showed that both extracts had antiproliferative effect, but the most prominent decrease in cellular growth was observed with glioblastoma cells

Ovarian cancer is among the most common causes of female mortality. Despite improvements in diagnostic methods, non-specific symptoms and delayed gynecological exams can lead to late-stage ovarian tumor discovery. In this study, the effect of an anti-cancer compound, 3-amino-N-(3-chloro-2-methylphenyl)-5-oxo-5,6,7,8-tetrahydrothieno[2,3-b]quinoline-2-carboxamide (Compound 1) was examined. Cytotoxicity, apoptosis, and metabolomic changes in ovarian cancer cell lines SK-OV-3 and OVCAR-3, as well as glycosphingolipid (GSL) expression, both on cancer stem cells (CSCs), marked as CD49f+ and non-CSCs (CD49f-) were explored. Treatment with Compound 1 reduced the percentage of CSCs compared to non-treated cells (P < 0.001). The expression of eight GSLs on CSCs and non-CSCs was examined using flow cytometry. Both cell lines showed a change in the glycophenotype of the cells, either up or down of its expression, after the treatment. These findings raise the possibility of specifically targeting CSCs in ovarian cancer therapy. Additionally, treatment of Compound 1 resulted in a statistically significant increase in both early and late apoptosis (P<0.001) suggesting a pivotal role in initiating programmed cell death by the apoptotic pathway. The metabolic analysis revealed that the treated cancer cells showed reduced metabolic activity compared to the control group (P < 0.001)

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Obstructive sleep apnea (OSA) often goes unrecognized despite common symptoms such as excessive daytime sleepiness, fatigue, and impaired quality of life (QoL). CPAP is the gold standard treatment for OSA, but optimal daily usage and time needed for observable effects remain unclear. This study aimed to investigate the short-term effects of CPAP on daytime sleepiness and QoL in patients with severe OSA. Medical records were collected from 87 patients with severe OSA who initiated CPAP therapy. Also, validated questionnaires were used before and after one month of CPAP to analyze QoL - the Calgary Sleep Apnea Quality of Life Index (SAQLI), the Cues to CPAP Use Questionnaire (CCUQ), and daytime sleepiness - the Epworth Sleepiness Scale (ESS). Multiple regression analysis was conducted to identify predictors of CPAP usage. Of the total participants aged 55.6±12.5, 77% were males, and 62% were CPAP adherent. Reductions in daytime sleepiness (ESS) were noted, as well as improvements in both overall QoL (SAQLI) and specifically in the domains of daily functioning, social interactions, emotional well-being, and symptom perception. Important cues for CPAP usage recognized by patients were physicians’ instructions and physicians’ worry regarding patients' condition. Furthermore, multiple regression revealed higher SAQLI scores and lower ESS scores as positive predictors of CPAP usage, along with lower AHI after one month of CPAP being associated with sufficient adherence.

As the carbon storage capacity of timber is recognized, there is growing interest in timber and wooden structures as a solution to various environmental problems. The use of Korean timber with substantial carbon storage capacity is required to reduce Korean carbon emissions and circulate timber resources. In this study, fire tests were conducted to investigate the charring properties of glued laminated timber columns made of Korean larch. The fire tests were conducted under both load-bearing and non-load-bearing conditions. The fire test results showed that the charring depth was affected by the corners of the section, and that the load ratio had an insignificant influence on the charring depth when the load ratio was 0.9 or less. This study provides data that can be used to compare the charring properties of laminated wood produced using South Korean larch with the charring properties of foreign standards. This provides reference data for developing fire-resistant design standards for timber structures made from South Korean timber.

Ab initio density functional theory molecular dynamics extensive calculations were used for the first time to evaluate stability conditions for relevant phases of InN. In particular, thermal decomposition of InN with formation of N2 molecules and pressure induced wurtzite – rocksalt solid-solid phase transition were established. The results consistent with available experimental data allowed a critical evaluation of potential and limitations of the proposed simulation method. The ab initio molecular dynamics as an efficient tool for simulations of phase transformations of InN including solid-solid structural transition and thermal decomposition with formation of N2 molecules has been demonstrated. It is of high interest because InN being important component of epitaxial quantum structures has still not been obtained as a bulk single crystal making difficult a determination of its basic physical properties and designing new applications.

Due to growing environmental concerns and stringent emissions regulations, optimizing the fuel consumption of marine propulsion systems is crucial. This work deals with the potential in an LNG ship propulsion system to reduce fuel consumption through controlled load distribution between engines in Dual Fuel Diesel Electric (DFDE) plant. Based on cyclical data acquisitioning measured on board and using an optimization model, the study evaluates different load distribution strategies between set up according to the optimization model results and automatic (equal) operation to determine their effectiveness in improving fuel efficiency. The analysis includes scenarios with different fuel types, including LNG, MDO and HFO, at different engine loads. The results indicate that load distribution adjustment based on the optimization model results significantly improves fuel efficiency compared to conventional methods of uniform load distribution controlled by power management systems almost in all load intervals. This research contributes to the maritime industry by demonstrating that strategic load management can achieve significant fuel savings and reduce environmental impact, which is in line with global sustainability goals. This work not only provides a framework for the implementation of more efficient energy management systems on LNG vessels, but also sets a benchmark for future innovations in maritime energy optimization as well as in the view of exhaust emission reduction.

The effects of psychological pressure on perceiving the height of a jump bar just before starting a high jump run was investigated. University students (N = 14) training for a high jump event performed 15 trials (3 practice, 6 pressure, and 6 non-pressure) in counterbalanced order in their daily practice environment. The height of the bar was judged as significantly higher on pressure trials compared to non-pressure trials. A regression analysis indicated that participants who reported increased subjective perceived pressure tended to judge the bar to be higher. There was no significant difference between pressure and non-pressure trials for the performance index, defined as the success rate. This study provides the first evidence that environmental perceptions prior to executing a motor task under pressure may make performance of the task appear to be more difficult.

The maneuverability of ships is influenced by several factors, including ship design, size, propulsion system, hull shape, and external conditions such as wind, waves, and currents. The size, shape, and arrangement of the hull, rudder, and propeller are decisive for maneuverability. Hydrodynamic forces such as bank effect and squat significantly impact the maneuverability of large ships in narrow channels. With the increasing trend of building ever-larger ships, the demand to evaluate the maneuvering performance of the ship at the design stage has become more critical than ever. Both experimental and computational methods are used to obtain accurate maneuvering characteristics of vessels. In this study, the methods for predicting ship maneuvering characteristics are analyzed using a systematic review based on the preferred reporting items for systematic reviews and meta-analyses (PRISMA). This article contributes to a deeper understanding of the hydrodynamic capabilities of ships and identifies possible future challenges in the field of ship hydrodynamics. The findings inform educators and the shipping industry about the importance of predicting the maneuvering performance of ships, with an emphasis on the education and training of seafarers needed to make timely decisions in critical situations.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

Tissue-like phantoms are widely used as a model for mimicking the optical properties of live tissue. This paper presents the results of a diffusion reflection method as well as fluorescence lifetime imaging microscopy measurements of fluorescein-conjugated gold nanorods in solution as well as inserted in solid tissue-imitating phantoms. A lack of consistency between the fluorescence lifetime results of the solutions and the phantoms raises a question about the ability of tissue-like phantoms to maintain the optical properties of inserted contrast agents.

Inflammatory bowel disease (IBD) is characterized by chronic inflammation of the gastrointestinal tract and encompasses two main subtypes, Crohn’s disease (CD) and ulcerative colitis (UC). IBD is frequently accompanied by extraintestinal manifestations (EIMs), with axial and peripheral spondyloarthritis (SpA) being the most common. Enthesitis, an inflammation of the bone insertions of capsules, ligaments, and tendons, represents an initial lesion in SpA. However, enthesitis remains an underestimated and often obscured EIM. The early detection of subclinical enthesial involvement in IBD patients using ultrasound (US) could provide an opportunity for timely intervention. While previous meta-analyses have reported on the incidence and prevalence of SpA in IBD, specific attention to enthesitis has been lacking. Therefore, this narrative review aims to resume the current knowledge on existing IBD-SpA cohorts, focusing specifically on enthesitis.

Using the example of III-V nitrides crystallizing in a wurtzite structure (GaN, AlN, InN), this review presents the special role of hydrostatic pressure in studying semiconductor properties. Starting with a brief description of high pressure techniques for growing bulk crystals of nitride compounds, we focus on the use of hydrostatic pressure techniques in both experimental and theoretical investigations of special properties of nitride compounds, their alloys and quantum structures. The band gap pressure coefficient is one of the most important parameters in semiconductor physics. Trends in its behavior in nitride structures, together with trends in pressure-induced phase transitions, are discussed in the context of the behavior of other typical semiconductors. Using InN as an example, the pressure-dependent effects typical of very narrow bandgap materials, such as conduction band filling or effective mass behavior, are described. Interesting aspects of bandgap bowing in In-containing nitride alloys, including pressure and clustering effects, are discussed.Hydrostatic pressure also plays an important role in the study of native defects and impurities, as illustrated by the example of nitride compounds and their quantum structures. Experiments and theoretical studies on this topic are reviewed. Special attention is given to hydrostatic pressure and strain effects in short periods nitride superlattices. The explanation of the discrepancies between theory and experiment in the optical emission and its pressure dependence from InN/GaN superlattices led to the well-documented conclusion that InN growth on the GaN substrate is not possible. The built-in electric field present in InGaN/GaN and AlGaN/GaN heterostructures crystallizing in wurtzite lattice can reach several MV/cm, leading to drastic changes in the physical properties of these structures and related devices. It is shown how hydrostatic pressure modifies these effects and helps to understand their origin.

This paper deals with the design and kinematic analysis of a novel mechanism for the elbow joint of an upper-limb exoskeleton, with the aim of helping operators, in terms of effort and physical resistance, in carrying out heavy operations. In particular, the proposed eight-bar el-bow joint exoskeleton mechanism consists of a motorized Watt I six-bar linkage and a suitable RP dyad, which connects mechanically the external parts of the human arm with the corre-sponding forearm by hook and loop velcro and thus, helping their closing relative motion for lifting objects during repetitive and heavy operations. This relative motion is not a pure rotation and thus, the upper part of the exoskeleton is fastened to the arm, while the lower part is not rigidly connected to the forearm, but through a prismatic pair which allows both rotation and sliding along the forearm axis. Instead, the human arm is sketched by means of a crossed four-bar linkage, which coupler link is considered as attached to the glyph of the prismatic pair, that is fastened to the forearm. Therefore, the kinematic analysis of the whole ten-bar mecha-nism, which is obtained by joining the Watt I six-bar linkage and the RP dyad to the crossed four-bar linkage, is formulated to investigate the main kinematic performance and for design purposes. The proposed algorithm has given several numerical and graphical results. Finally, a double-parallelogram linkage, as particular case of the Watt I six-bar linkage, was considered in combination with the RP dyad and the crossed four-bar linkage, by giving a first mechanical de-sign and a 3D printed prototype.

As motor capacity and rated voltage increase, the demand for motor insulation also increases. Additionally, the electric field distribution at the end of a large-scale hydro generator is extremely non-uniform, and corona discharge readily occurs. This destroys the main insulation, which significantly affects the service life of electrical machinery. Thus, the regulation of the electric field concentration at the end of a large-scale hydro generator needs to be addressed. There are many problems in resistance–capacitance chain model research. Particularly, these models cannot accurately reflect the insulation, corona structure, and electric field distribution in electrical machinery. Additionally, the corner electric field and loss distributions cannot be obtained, leading to a higher calculation error. The electric field distribution at the motor end and the loss distribution were analyzed using the finite-element method. First, by applying the basic principles of electric circuits and electromagnetic field theory, we calculated the electric field distribution at the stator bar end. Second, a 3D model of the stator bar was built using Creo Parametric, yielding a model that is more closely related to the prototype wirebar model. Then, the potential, electric field, and loss distributions around the stator bar were simulated by using COMSOL simulation software. The effects of the circular arc corner, nonlinearity coefficient, anti-corona coating length, and resistivity of the stator bar on the electric field distribution at the motor end were explored.

This study investigates the mean annual water temperature trends at the confluence of the Sava and Danube Rivers, along with air temperature trends at the Belgrade meteorological station, spanning from 1956 to 2020. Results reveal a consistent increase in temperature across all three measuring stations, with the Danube experiencing a rise of 0.34°C/10 years, the Sava at 0.44°C/10 years, and Belgrade's air temperature increasing by 0.39°C/10 years. Employing the RAPS method, sharp rises in water temperature were pinpointed in 1989 for the Sava and 1990 for the Danube, while Belgrade's air temperature surge began in 1998. The highest intensity of air temperature increase within the recent period (1998-2020) was observed at the Belgrade observatory, reaching 0.76°C/10 years. Notably, the Sava exhibited a faster increase in water temperature over the last thirty years compared to the Danube. August marked the peak average water temperature for both rivers, while July recorded the highest average air temperature in Belgrade. Despite differing flow rates, both rivers exhibit similar hydrological regimes, with maximum flows occurring in April and minimum flows in August for the Sava, and October for the Danube. Seasonal temperature increases were most pronounced in summer, notably in August, with the smallest rises occurring during cold periods. Additionally, an inverse proportional relationship between mean annual water temperatures and discharges was observed at both river stations.

There is a need to find innovative learning methods that enable accelerated learning of ‎a foreign language. This study examined the effect of computer-assisted language ‎learning (CALL) in acquiring a foreign language, which combines cognitive and ‎emotional stimuli in the background. ‎ The study explored two factors related to the acquisition of a foreign language: the ‎duration and scope of the learning process and the depth of internalization of the newly ‎acquired language. Another objective was to assess the learning method in two ‎learning environments, a multimedia setting and a virtual reality headset (VRH), to ‎determine if the learning environment affects the learning results and leads to better ‎vocabulary retention. ‎ One hundred native French speakers, with an average age of 47.5, participated in the ‎study and had no prior knowledge of a new native language. We randomly divided the ‎participants into two groups (multimedia and VRH). They studied 550 words in a new ‎native language for five days: 30 minutes each evening and 15 minutes in the morning.‎ The post-learning test pointed out that both groups improved their vocabulary scores ‎significantly. Approximately one month after the learning experience, we administered ‎a knowledge retention test to 32 participants and found that the level of knowledge had ‎been retained. Finally, background variables (e.g., gender, age, previous knowledge of ‎the new native language) did not affect the learning results. ‎ The findings indicate that CALL, which integrates background cognitive and ‎emotional stimuli in both learning environments, significantly accelerates learning ‎pace, broadens the scope of newly acquired words, and ensures retention. The level of ‎improvement observed in our study is notably higher than reported in the literature ‎that had previously evaluated CALL and in-class language acquisition.

Background/Objectives: RAS is associated with coronary artery disease (CAD), exacerbation of arterial hypertension and progression to heart failure, but remains frequently unrecognised in clinical practice. Methods: We conducted a systematic review and meta-analysis of studies by pooling data of patients undergoing CAG due to suspected or stable CAD that received a bilateral renal artery angiography; Results: A total of 31 studies with 31,689 patients were included (mean age 63.2±8.7 years, 20.9% were female). Overall, 13.4% (95%CI 10.5-16.7%) of patients undergoing coronary angiography had significant RAS, with 6.5% (95% CI 4.5-8.9%) and 3.7% (95%CI 2.5-5.2%) having severe and bilateral RAS. The mean weighted proportion of patients with 3-vessel coronary disease (3VD) was 25.1 (95%CI 19.6-30.9%) while 4.2% (95%CI 2.6-6.2%) had leftmain (LM) coronary disease. Patients with RAS compared to those without RAS were significantly older (mean difference - MD 4.2 years, (95%CI 3.8-4.6). The relative risk of RAS was greater for the female sex (risk ratio, 95%CI; RR 1.3, 1.03-1.57), presence of diabetes (RR 1.2, 1.10-1.36), arterial hypertension (RR 1.3, 1.21-1.46), dyslipidemia (RR 1.1, 1.06-1.14), peripheral artery disease-PAD (RR 2.1, 1.40-3.16), chronic kidney disease-CKD (RR 2.6, 2.04-3.37), 3VD (RR 1.6, 1.30-1.87), and LM disease (RR 1.8, 1.28-2.47). Smoking had a neutral effect on the risk of RAS occurrence (RR 1.0, 0.94-1.06); Conclusions: RAS is common in patients undergoing coronary angiography. CKD, PAD, older age, and severe CAD were among the strongest predictors for the presence of significant RAS.

The ordinary 3D wave equation for nondissipative, homogeneous, isotropic media admits solutions where the point sources are permitted to move, but it does not admit solutions where the receiver is allowed to move. To overcome this limitation, the new wave equation is derived, permitting both the receiver and the source to move. This new wave equation is a generalization of the standard wave equation, and it reduces to the standard wave equation when the receiver is at rest. To derive this new wave equation, we first mathematically define a diverging spherical wave caused by the stationary point source. From this purely mathematical definition, the wave equation for the stationary source and the moving receiver is derived together with the corresponding free-space Green's function. Utilizing the derived Green's function, it was shown that this new wave equation also permits the solutions where both the receiver and the source are permitted to move. In conclusion, this paper demonstrates that, instead of an ordinary wave equation, the wave equation for the moving source and the moving receiver governs the waves emitted by the moving point sources and received by the moving receivers.

To examine the effect of synchronous dance movements on social bonding and perceived closeness between generations, 168 young (20-45 years) and older (65-90 years) participants were randomly assigned to six dyad conditions. These included dancing synchronously or asynchronously with an in-age-group or an out-age-group unfamiliar partner for 11 minutes. Participants completed social bonding and groups’ closeness questionnaires. To assess variation across individuals’ and dyads’ measurements, a generalized estimating equations modeling analysis was conducted. In line with the first two hypotheses, synchronized dance increased social bonding, and young adults showed enhanced perception of closeness between generations. Hypothesis 3 that synchronous dance with out-age-group members would foster greater perceived closeness compared to in-age-group members was not confirmed. Surprisingly, results indicated that asynchronous movements with the in-age-group led to a higher degree of closeness between generations than asynchronous movements with the out-age-group. The study offers new directions for practitioners in welfare, nursing, and therapy fields, particularly for engaging young adults in intergenerational dance interventions.

In reservoir engineering, one of the main sources of information for the characterization of reservoir and well parameters is well testing. Among the unconventional well testing methodologies, Harmonic Well Testing (HPT) is appealing from an economic standpoint because it could provide well performance and reservoir behavior monitoring without having to interrupt field production. Recorded pressure analysis is performed in the frequency domain by adopting a derivative approach similar to conventional well testing. To this end, pressure and rate data must be decomposed into harmonic components. Test interpretability can be significantly improved if pressure data are detrended prior to interpretation, filtering out non periodic events such as discontinuous production from neighboring wells and flow regime variations which did not respect the designed test periodicity. Therefore, detrending offers the possibility of overcoming the limitation of HPT applicability due to the difficulty of imposing a regularly pulsing rate for the whole test duration (typically lasting several days). This makes HPT attractive for well performance monitoring, especially in gas storage fields. In this paper, the application of different detrending methodologies to synthetic HPT pressure data generated in different reservoir and operational scenarios is presented and discussed. Moreover, a real case application is also presented.

Views of aging include peoples’ assessment of their own aging process and their subjective age. Positive aging views relate to good psychological well-being which predicts better physical and mental health. While these were substantially studied, the moderating roles of self-aging attitudes and psychological well-being in the subjective age-age discrimination connection have been much less explored. The current study used a convenience sample of 568 participants (mean = 66.21y, SD = 11.95, age range 50-95), 55.8% women, 67.1% employed. In line with the hypotheses, young subjective age and psychological well-being were connected to less age discrimination in the workplace and higher psychological well-being mitigated the subjective age-age discrimination at work connection. When the perception of old age as a period of loss was added to the model, adults who perceived old age as a period of loss and reported lower levels of psychological well-being, demonstrated the strongest relationship between an increase in subjective age and an increase in age-related discrimination at work. The findings emphasize the importance of the psychological well-being of older employees as a resource for improving their attitudes to their last years at work.

In a recent paper, Nicolas Gisin suggests that by conducting physics with intuitionistic rather than classical mathematics, rich temporality - that is, passage and tense, and specifically, the future’s openness - can be incorporated into physics. Physics based on classical mathematics is tenseless and deterministic, and that, so he holds, renders it incongruent with experience. According to Gisin, physics ought to represent the indeterminate nature of reality, and he proposes that intuitionistic mathematics is the key to succeeding in doing so. While I share his insistence on the reality of passage and tense, and on the future being real and open, I argue that the amendment he offers does not work. I show that, its attunement to time notwithstanding, intuitionistic mathematics is as tenseless as classical mathematics, and that physics is bound to remain tenseless regardless of the math it employs. There is much to learn about tensed time, but the task belongs to phenomenology and not to physics.

Age is the primary risk factor for neurodegenerative diseases such as Alzheimer’s and Huntington’s disease. Alzheimer’s disease is the most common form of dementia and a leading cause of death in the elderly population of the United States. No effective treatments for these diseases currently exist. Identifying effective treatments for Alzheimer’s, Huntington’s, and other neurodegenerative diseases is a major current focus of national scientific resources, and there is a critical need for novel therapeutic strategies. Here we investigate the potential for targeting the kynurenine pathway metabolite 3-hydroxyanthranilic acid (3HAA) using Caenorhabditis elegans expressing amyloid-beta or a polyglutamine peptide in body wall muscle, modeling proteotoxicity in Alzheimer’s and Huntington’s disease-related, respectively. We show that knocking down the enzyme that degrades 3HAA, 3HAA dioxygenase (HAAO) delays age-associated paralysis in both models. This effect on paralysis was independent of protein aggregation in the polyglutamine model. We also show that the mechanism of protection against proteotoxicity from HAAO knockdown is mimicked by 3HAA supplementation, supporting elevated 3HAA as the mediating event liking HAAO knockdown to delayed paralysis. This work demonstrates potential for 3HAA as a targeted therapeutic in neurodegenerative disease, though the mechanism is yet to be explored.

Advanced Finite Element (FE) modeling and simulations were performed on vehicular crashes into a Three-bar Metal Bridge Rail (TMBR). The FE models of a sedan, a pickup truck, and a TMBR section were adopted in the crash simulations subject to Manual for Assessing Safety Hardware (MASH) Test Level 2 (TL-2) and Test Level 3 (TL-3) requirements. The test vehicle models were first validated using full-scale physical crash tests conducted on a two-bar metal bridge using a sedan and a pickup truck with similar overall physical properties and sizes to their respective vehicles used in the simulations. The validated vehicular models were then used to evaluate the crash performance of the TMBR using MASH Evaluation Criteria for structural adequacy, occupant risk, and post-impact trajectory. The TMBR met all MASH TL-2 requirements but failed to meet the MASH TL-3 Criteria H and N requirements when impacted by the sedan. The TMBR was also evaluated under in-service conditions (behind a 1.52-m wide sidewalk) and impacted by the sedan under MASH TL-3 conditions. The simulation results showed that the TMBR behind a sidewalk met all safety requirements except for the occupant impact velocity in the longitudinal direction, which exceeded the MASH limit by 3.93%.

Theory of the Thermal Response Testing (TRT) is a well-known part of sizing process of the geothermal exchange system. Multiple parameters influence accuracy of effective ground thermal conductivity measurement; like testing time, variable power, climate interferences, groundwater effect etc. To improve accuracy of the TRT we introduced procedure to additionally analyze falloff temperature decline after power test. Method is based on a premise of analogy between TRT and petroleum well testing, since origin of both procedures lies in diffusivity equation with solutions for heat conduction or pressure analysis during radial flow. Applying pressure build-up test interpretation technique to the borehole heat exchanger testing, greater accuracy could be achieved since ground conductivity could be obtained from this period. Analysis was conducted on coaxial exchanger with five different power steps, and with both direct and reverse flow regime. Each test was set with 96hr of a classical TRT, followed by 96hr of temperature decline, making it almost 2000 hours of cumulative borehole testing. Results showed that ground conductivity value could vary as much as 25% depending on test time, seasonal period and power fluctuations while thermal conductivity obtained from a falloff period gives more stable values with only 10% value variation.

: Soil free living nematodes community composition was compared for five agro-management systems in a basaltic soil. The sites differed in their long-term management system and were designated as organic farming (OM), conventional (MI), natural pasture (NP), foliage farming (FF) and open field (OF). The effect of five diverse land use types in vineyard growth in basaltic soils on soil free living nematodes, density, diversity, and functionality in the plant rhizosphere was examined. We found 22 families, 42 genera of which only 14 genera were present in all soil samples, three bacteria feeders, 4 fungi feeders, 3 omnivores-predators and 4 plant parasites, in the soil collected from the five sampling sites. The organic and conventional managements were found to influence soil free living nematode community and its trophic composition. The higher abundance of bacteria feeders included the Cephalobidae and Panagrolaimidae families. The fungi feeders included the Anguinidae and Aphelenchidae families. Ominvores-predators included the Aprocelaimidae and Qudsianematidae, and the plant parasites included the Anguinidae (genus Anguina), Nothotylenchidae and Tylenchidae families. The changes in plant parasite nematodes were one of the main pests in the below-ground rhizosphere biome. Promoting the bacterial community could be a beneficial and promising way for a considerable increase in organic management.

Utility perceived by individuals is believed to be different from the utility experienced by that individual. System dynamicists implicitly categorize this phenomenon as a form of bounded rationality and traditionally employ a simple smoothing function to capture it. We challenge this generalization by testing it against an alternative formulation of utility perception that is suggested by modern theories of behavioral economics. In particular, the traditional smoothing formulation is compared with the peak-end rule in a simple theoretical model as well as in a medium-size model of electronic health record implementation. Experimentation with the models reveals that the way utility perception is formulated is important and might affect behavior and policy implications of system dynamics models.

In this paper, we investigate a class of hierarchical variational inequalities (HVIPs, i.e., strongly monotone variational inequality problems defined on the solution set of multiple-set split common fixed point problems) with quasi-pseudocontractive mappings in real Hilbert spaces, which special cases can be found in many important engineering practical applications such as image recognizing, signal processing and machine learning. In order to solve HVIPs of potential application value, inspired by the primal-dual algorithm, we propose a novel accelerated cyclic iterative algorithm that combines the inertial method with a correction term and a self-adaptive step-size technique. Our approach eliminates the need for prior knowledge of the bounded linear operator norm. Under appropriate assumptions, we establish strong convergence of the algorithm. Finally, we apply our novel iterative approximation to solve multiple-set split feasibility problems and verify the effectiveness of the proposed iterative algorithm through numerical results.

This paper is a study of a generalization of the quantum Riemannian Hamiltonian evolution, previously analyzed by us in our work [6], in the geometrization of quantum mechanical evolution in a Finsler geometry. We find results with dynamical equations governing the evolution of the trajectories defined by the expectation values of position. The analysis appears to provide an underlying geometry described by a geodesic equation, with connection form with a second term which is an essentially quantum effect. These dynamical equations provide a new geometric approach to the quantum evolution where we suggest a definition for "local instability" in the quantum theory.

The compatibility between the de Sitter Swampland conjecture and Ho\v{r}ava-Lifshitz $F(\bar{R})$ theories with a flat FLRW metric is studied. We first study the standard $f(R)$ theories and show that the only way in which the dS conjecture can be made independent of $R$ is by considering a power law of the form $f(R)\sim R^{\gamma}$. The conjecture and the consistency of the theory puts restrictions on $\gamma$ to be greater but close to $1$. For the $F(\bar{R})$ theories described by its two parameters $\lambda$ and $\mu$ we use the equations of motion to construct the function starting with an ansatz for the scale factor in the Jordan frame of the power law form. By doing a conformal transformation on the three metric to the Einstein frame we can obtain an action of gravity plus a scalar filed by relating the parameters of the theory. The non-projectable and projectable cases are studied and the differences are outlined. The $F(\bar{R})$ function obtained consists of terms of the form $\bar{R}^{\gamma}$ with the possibility of having negative power terms. The dS conjecture leads to inequalities for the $\lambda$ parameter, in both versions it gets restricted to be greater but close to $1/3$. For the general case in which $\mu$ and $\lambda$ are considered as independent, the action contains an extra term but we propose that the conjecture is still applicable. Once again the non-projectable and projectable cases are studied. The $F$ function obtained has the same form as before, the consistency of the theory and the dS conjecture lead to a set of inequalities on both parameters that are studied numerically. In all cases $\lambda$ is restricted by $\mu$ around $1/3$ and we obtain $\lambda\to1/3$ if $\mu\to0$. Finally we consider the $f(R)$ limit $\mu,\lambda\to1$ and we obtain consistent results.

(1) Background: Since microplastics in the aquatic environment are difficult to prevent and can cause adverse physiological and biochemical reactions to various organisms, we aimed to analyze the effectiveness of an eco-friendly removal method using aquatic plants with high ornamental value and excellent water purification ability. (2) Methods: Iris pseudacorus and Lythrum anceps were planted in tap water contaminated with microplastics to analyze the removal rate and root adsorption of microplastics. (3) Results: The amount of microplastics in the planting boxes of Iris pseudacorus and Lythrum anceps was significantly reduced, and the adsorption of microplastics on the roots was confirmed. (4) Conclusions: It was found that the removal of microplastics in water by aquatic plants is effective and that microplastic pollution does not significantly affect plant growth. However, the removal of microplastics by adsorption on plant roots may be affected by various environmental factors, so it is necessary to consider various limitations.

Olivine-like NaFePO4 glasses and nanocomposites are promising materials for cathodes in sodium batteries. Our previous study concerned the influence of high pressure on DC electric conductivity of NaFePO4 glasses. This work presents the results of AC measurements of glasses and nanocomposites from pressure treatment. Depending on the temperature range, the electronic conduction mechanism changed from variable range hopping (between Fe2+/Fe3+centers) to phonon-assisted hopping. For DC electric conductivity the portrayal via the classic Mott’s Variable Range Hopping is limited to low temperatures. Spectra of AC conductivity for glasses and pressure-formed nanocomposites fulfill Jonscher’s scaling law with power exponents ranging from 0.3 to 0.9 depending on temperature and the electron hopping mechanism. Due to the decrease in distance between hopping centers, an increase of AC conductivity around 2-3 orders of magnitude was observed after high pressure-high temperature treatment. Up to 200 K temperature dependencies of AC conductivity follow the pattern suggested by Mott's theory. Above that temperature corresponds to phonon-assisted hopping with activation energies EAC≈0.40 eV (for glass: amorphous solid) and EAC≈0.18 eV (for glass + nanocrystallites nanocomposite). Notable that they are considerably lower than values of EDC for DC conductivity. Results obtained show that high-temperature compressing, just below the glass temperature, significantly leads to a stable decrease in distance between hopping centers related to nanocrystallites in a glassy matrix. Consequently, it leads to an essential rise in electric conductivity and volumetric capacity. AC spectra of electronic conductivity are disturbed by the conduction of Na+ mobile ions, which impacts polaron conductivity and can be a limiting factor for conductivity.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

As split learning (SL) becomes popular for addressing data privacy and resource limitation issues in edge model training process, it is crucial to pre-validate whether the extensive use of wireless and computing resources in SL can achieve the expected training latency and convergence. While digital twin network (DTN) can potentially estimate network strategy performance in pre-validation environments, they are still in their infancy for SL tasks, facing challenges like unknown non-i.i.d. data distributions, inaccurate channel states, and misreport resource availability across devices. To address these challenges, this paper proposes a TransNeural algorithm for DTN pre-validation environment to estimate SL latency and convergence. First, the TransNeural algorithm integrates transformers to efficiently model data similarities between different devices, considering different data distributions and device participate sequence greatly influence SL training convergence. Second, it leverages neural network to automatically establish the complex relationships between SL latency and convergence with data distributions, wireless and computing resources, dataset sizes, and training iterations. Deviations in user reports are also accounted for in the estimation process. Simulations show that the TransNeural algorithm improves latency estimation accuracy by 13.44% and convergence estimation accuracy by 116.74% compared to traditional equation-based methods.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Hox gene clusters are crucial in Embryogenesis. It was observed that some Hox genes are located in order along the telomeric to centromeric direction of the DNA sequence: Hox1, Hox2, Hox3…. These genes are expressed in the same order in the ontogenetic units of the Drosophila embryo along the Anterior-Posterior axis. The two entities (genome and embryo) differ significantly in linear size and in-between distance. This strange phenomenon was named Spatial Collinearity (SP). Later, it was observed that, particularly in the Vertebrates, a Temporal Collinearity (TC) coexists: first is Hox1 expressed, later Hox2 and even later Hox3,…,. According to a Biophysical Model (BM), pulling forces act at the anterior end of the cluster while a cluster fastening applies at the posterior end. Hox clusters are irreversibly elongated along the force direction. During Evolution, the elongated Hox clusters are broken at variable lengths thus split clusters may be created. An Empirical Rule was formulated distinguishing development due to a complete Hox cluster from development due to split Hox clusters. BM can ‘explain’ this Empirical Rule. In a spontaneous mutation where the cluster fastening is dismantled, a weak pulling force automatically shifts the cluster inside the Hox activation domain. This cluster translocation can probably explain the absence of Temporal Collinearity in Drosophila.

Background: This study aimed to develop a highly consumable collagen-containing bar that contributes to enriching the diets of elderly individuals in terms of energy and nutrients. Method: For this purpose, after the development of 5 different bar samples (C, P1, P2, D1, D2) containing different amounts of collagen, date puree, and pumpkin puree, they were evaluated in terms of sensory and nutritional properties. Results: The highest flavor score bars were those with high levels of pumpkin puree (P2) and date puree (D2). By applying the TOPSIS technique, which is used when there are multiple crite-ria among multiple samples, to the snack bar samples with different contents, the most liked sample was found to be the snack bar (D2) with a high level of date puree. One serving of the developed bars contains approximately 300-400 kcal of energy and 6.8-8.8 g of protein. Consid-ering age-related decreased appetite and chewing and swallowing problems in elderly individ-uals, regular consumption of nutrient-rich small meals or snacks with enhanced sensory charac-teristics will contribute to improving their nutritional and functional status.

Nano medicine seeks to deliver a valuable set of research tools and clinically useful devices in the near future. The current medical field is in dire need of new commercial applications in the pharmaceutical industry that may include advanced drug delivery systems, new therapies, and in vivo imaging. Here in this experimental study, the nano materials used in DNA biosensors like silver nano dots were incorporated as nano biosensors are used for both therapeutic and diagnostic applications. The most important step while preparing a DNA biosensor is the immobilization of DNA probe on the surface of a sensing device such as an electrode. The amount of immobilized DNA probe will influence the accuracy sensitivity, selectivity and life of a DNA biosensor directly. Because of the high surface to volume ratio and excellent biological compatibility, nano materials can enlarge the sensing surface area to increase the amount of immobilized DNA and the DNA mixed with nano materials can keep its biologically activity well.In this study,silver nano dots created in our lab were functionalized with thio nucleides and were used as nano sensor probes in bio bar code assays.

To achieve a fast testing on barrier properties of organic coatings, immersion test, AC-DC-AC test, and coupled test of AC-DC-AC with hydrostatic pressure were conducted in seawater for a glass flake epoxy coating. Electrochemical impedance spectroscopy (EIS) was used to characterize the degradation processes of the coating during the tests, and the surface of the coating was analyzed using optical microscope, scanning electron microscope (SEM) and Fourier transform infrared spectrometer (FTIR). The results show that the periodically cathodic polarization coupled with high hydrostatic pressure can accelerate the degradation of the coating by facilitating the diffusion and uptake of electrolyte and the delamination of the coating. The coupled test method has the largest acceleration due to the synergetic effect of AC-DC-AC and hydrostatic pressure.

A testable hypothesis with quantitative predictions is put forward, proposing that strong acids produced on land at a rate correlated with global population are an increas-ing cause of increasing atmospheric CO2 pressure (pCO2). This hypothesis widens the imbalance assumed between the global uptake of CO2 by photosynthesis and emissions of CO2 from all sources, including the combustion of fossil fuels, causing greater atmos-pheric pCO2. Our modelling tests for reactions of dissolved inorganic carbon show that increasing atmospheric CO2 is caused thermodynamically by falling land surface pH values, but only with bicarbonate present. Strong acids generated by oxygen from re-duced inorganic compounds of nitrogen and sulphur emit CO2 almost stoichiometrically from dissolved bicarbonate in the pH range of most global soils, between 6 to above 8. We show that each decrease of aqueous pH value of 0.01 units from acidification of sur-face water near pH 8 potentially increases the pCO2 in the atmosphere by about 7 ppmv. The surface pH value of the ocean near 8.10 in 2000 has been shown to decrease at this rate, a result of equilibrating with the rising atmospheric pCO2. Therefore, our qualita-tive estimates of increasing atmospheric CO2 driven by irreversible acidification on land are critical and need broad scale validation. Unfortunately, these acidifying processes on land from excessive nitrogen fertiliser, export of alkaline produce from farmlands and other processes were not considered by previous biogeochemical reviews. However, several very recent research studies showing CO2 emissions from soil during nitrifica-tion are consistent with our hypothesis. Despite counter measures to curb excessive CO2 emissions, including carbon capture and geological storage, the increasing Keeling curve for pCO2 may continue to rise because zero carbon policies do not address these causes. We recommend that this hypothesis be further tested by in situ experiments in neutral soils and water, designed to compare CO2 emissions under the acidifying conditions de-scribed in this article. Corrective counter measures can then be designed and applied.

The capacitor-mismatch among diverse defects caused by the manufacturing process variations significantly affects the linearity of capacitor-array used to implement the capacitive digital-to-analog converter (CDAC) in the successive-approximation-register (SAR) analog-to-digital converter (ADC). Accordingly, the linearity of the SAR ADC is limited by that of capacitor-array, resulting in serious yield loss. This paper proposes an efficient foreground self-calibration technique to enhance the linearity of the SAR ADCs by mitigating the capacitor-mismatch based on the split ADC architecture along with variable capacitors. In this work, two ADC channels (i.e., ADC1 and ADC2) for the split ADC architecture include their capacitive DACs (CDACs) whose binary-weighted capacitor-arrays consist of variable capacitors. A charge-sharing SAR ADC is used for each ADC channel. In the normal operation mode, their digital outputs are averaged to be the final ADC output, as in a conventional split ADC. In the calibration mode, every single binary-weighted capacitor for the two ADCs is sequentially calibrated by making parallel or/and antiparallel connection among two or thee capacitors from the two channels. For instance, because the capacitors of the CDACs ideally exhibit the binary-weighted relation as Cn=2×Cn−1, variable capacitor Cn of ADC1 can be updated to be closest to the sum of Cn−1 of ADC1 and Cn−1 of ADC2 for the calibration. For the process, the two capacitor-arrays of the two ADCs can be reconfigured to be connected to each other, so that Cn of ADC1 can be connected with two of Cn−1 of ADC1 and ADC2 in antiparallel. The two voltages at the top and the bottom plates of the CDAC are compared by a comparator of ADC1, and the comparison results are used to update Cn. This process is iterated, until Cn is in agreement with the sum of two of Cn−1. Finally, all the capacitors can be calibrated in this way to have the binary-weighted relation. The simulation results based on the proposed work with a split SAR ADC model verified that the proposed technique can be practically used, by showing that the total-harmonic-distortion and the signal-to-noise-and-distortion ratio were enhanced by 21.8-dB and 6.4-dB, respectively.

The article presents the Base Point Split (BPSplit) algorithm for generating a polygon skeleton based on sets of vector data describing lakes and rivers. A key feature of the BPSplit algorithm is that it is dependent on base points representing the source or mouth of a river or a stream. The input values of base points determine the shape of the resulting skeleton. Various skeletons can be generated with the use of different base points. Base points are applied to divide polygon boundaries into segments. Segmentation supports the selection of TIN edges inside polygons. The midpoints of selected TIN edges constitute a basis for generating a skeleton. The algorithm handles polygons with numerous holes, and it accounts for all holes. This article proposes a method for modifying a complex skeleton with numerous holes. In the discussed approach, skeleton edges that do not meet the preset criteria (e.g. that the skeleton is to be located between holes in the center of the polygon), are automatically removed. A simple algorithm for smoothing zigzag lines was proposed.

Background: A new access technique was developed to reduce postoperative adverse events after the extraction of impacted maxillary wisdom teeth. Hence, this study aimed to assess the occurrence of adverse events after extraction of maxillary impacted wisdom teeth using traditional or modified access. Methods: Two different surgical incision designs were used for bilateral wisdom tooth extractions in 30 patients. The traditional incision was performed distal to the second molar in the center of the tuberosity, followed by a buccal releasing incision. After tooth extraction the wound was secured by sutures. The new technique consists of an oblique incision from the distal palatal aspect of the tuberosity towards the buccal aspect of the second molar. After tooth extraction, cyanoacrylate glue was used on the wound. Results: Lower pain was reported by patients at the site treated with the new technique (p<0.01). Edema, postsurgical bleeding, and hematoma were similar in both groups. The surgical time was shorter for the new technique (p<0.01). Conclusions: The new technique applied for the extraction of impacted maxillary wisdom teeth reduced postsurgical pain and the duration of surgery.

In the present investigation, the crank-slider and crank-rocker off-center mechanisms are used to control 1-DOF in a solar tracker focused on improving the conversion of solar to electrical energy. Likewise, the kinematic equations of these mechanisms are presented that allow us to know their operating pattern in the work range of the follower and their comparative analysis between them. Finally, the scale construction with 3D printing is shown to verify the functionality of each 4-bar system.

Parallel manipulators with multiple end-effectors bring us interesting advantages over conventional parallel manipulators such as improved manipulability, workspace and avoidance of singularities. In this work the kinematics of a five-bar planar parallel manipulator equipped with two end-effectors is approached by means of the theory of screws. As an intermediate step the displacement analysis of the robot is also investigated. The input-output equations of velocity and acceleration are systematically obtained by resorting to reciprocal-screw theory. In that regard the Klein form of the Lie algebra se(3) of the Euclidean group SE(3) plays a central role. In order to exemplify the method of kinematic analysis, a case study is included. Furthermore, the numerical results obtained by means of the theory of screws are confirmed with the aid of special software like ADAMS.^TM

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

Energy drink (ED) consumption among Israeli-Arab adolescents is widespread. This study aimed to investigate the acute glycemic and insulin effects of EDs in healthy adolescents. Seventy-one Israeli-Arab adolescents (56% girls, average age 16.04±1.03 years) participated in a non-randomized, case-controlled, open-label study. Participants consumed ED (n=36) or a volume- and carbohydrate-matched non-caffeinated soft drink (SD, n=35), followed by a 2 h glucose tolerance test. Blood glucose was measured at baseline and 15, 30, 60, and 120 minutes post-consumption (T0, T15, T30, T60 and T120, respectively). Serum insulin concentration and caffeine relative intensity were determined 45 minutes post-consumption (T45). Blood glucose levels peaked significantly at T15 and remained significantly higher at T30 in the ED group compared to the SD group (p=0.005, p=0.017, respectively). Insulin concentrations were substantially higher at T45 in the ED group (t[64]=2.794, p=0.001). This pattern was especially prominent in heavy ED consumers. A positive correlation emerged between the amount of caffeine consumed (mg/kg), blood glucose levels at T15 and T30, and insulin concentration at T45. This study is the first to demonstrate the glycemic and insulin responses to ED consumption in adolescents, suggesting that regulatory measures limiting ED sales to adolescents could improve their health.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

Autism spectrum disorder (ASD) is a common condition with lifelong implications and a strong hereditary component suggesting genetic underpinnings. The last decade has seen dramatic improvements in DNA sequencing and related bioinformatics and databases. We analyzed the raw DNA sequencing files on the Variantyx® bioinformatics platform for the last 50 ASD patients evaluated with trio whole genome sequencing (trio-WGS). “Qualified” variants were defined as coding, rare, and evolutionarily conserved. Primary Diagnostic Variants (PDV) additionally were in genes directly linked to ASD and matched clinical correlation. A PDV was identified in 34/50 (68%) of cases, including 25 (50%) cases with heterozygous de novo and 10 (20%) with inherited variants. De novo variants in genes directly associated with ASD were far more likely to be Qualifying than non-Qualifying versus a control group of genes not associated with ASD (P = 0.0002, odds ratio 29), validating that most are indeed disease related. Only 14/34 (41%) of PDV cases had the variant listed on the laboratory report, and reanalysis increased diagnostic yield from 28% to 68%. Variants that we assigned as PDVs yet not on the report were predominately de novo in genes not yet reported as ASD associated. Many subjects both with and without a PDV had inherited Qualifying variants in known ASD-associated genes, suggesting polygenic inheritance. Thirty-three subjects (66%) had treatment recommendation(s) based on DNA analyses. Our results demonstrate high yield of trio-WGS for revealing molecular diagnoses in ASD that is greatly enhanced by re-analyzing DNA sequencing files. In contrast to previous reports, de novo variants dominate the findings, mostly representing novel conditions. This has implications to the cause and rising prevalence of autism.

Background: This study aimed to evaluate the burden and impact of cardiac and cerebrovascular disease (CCD) on hospital inpatients with type 1 diabetes mellitus (T1DM). Methods: This is a retrospective nationwide cohort study of people with T1DM with or without CCD in the US National Inpatient Sample between 2016 to 2019. The in-hospital mortality rates, length of stay (LoS) and healthcare costs were determined. Results: A total of 59,860 T1DM patients had a primary diagnosis of CCD and 1,382,934 did not. The median LoS was longer for patients with CCD compared to no CCD (4.6 vs. 3 days). Patients with T1DM and CCD had greater in-hospital mortality compared to those without CCD (4.1% vs. 1.1%, p<0.001). The estimated total care cost for all patients with T1DM with CCD was approximately US $326 million. The adjusted odds of mortality compared to patients with non-CCD admission was greatest for intracranial hemorrhage (OR 17.37, 95%CI 12.68-23.79), pulmonary embolism (OR 4.39, 95%CI 2.70-7.13), endocarditis (OR 3.46, 95%CI 1.22-9.84), acute myocardial infarction (OR 2.31, 95%CI 1.92-2.77) and stroke (OR 1.47, 95%CI 1.04-2.09). Conclusions: The burden of CCD in patients with T1DM is substantial and significantly associated with increased hospital mortality and high healthcare expenditures.

Diastematomyelia, also known as split cord syndrome, is a congenital disorder of the spinal cord. As the name suggests, the spinal cord is split into two resulting in neurological complaints associated with cutaneous symptoms. Although the diagnosis can be done clinically, for disease confirmation, various radiological investigations are used for the diagnosis of this condition. Here, we present a case of a 54-year-old Indian female diagnosed with diastematomyelia. The clinical features, diagnostic modalities, treatment options and prognosis of this condition have been discussed.

Many studies utilize sensors to measure foot plantar pressure and analyze gait patterns, often focusing on assessing weight-bearing symmetry or asymmetry compared to control groups. However, a critical question arises: does the selection of the control group significantly impact study outcomes? Does chronic low back pain affect foot plantar pressure measurements? This experimental study involved 23 participants, including healthy individuals and those without foot disorders but with chronic low back pain. Dynamic foot pressure measurements were conducted using the Ortopiezometr, and data were analyzed using the "Steps" program. Participants were divided into two groups: Group 1 comprised completely healthy individuals, while Group 2 consisted of individuals without foot problems but with moderate chronic low back pain. The findings highlight a prevalence of energy release in the forefoot sensors compared to the hindfoot for both the right and left legs in most cases. Even among healthy volunteers, achieving perfect symmetry in the maximum values on the sensors for the right and left feet was a challenge. Results showed no statistically significant differences in energy released on specific sensors or duration of gait phases between the groups. Essentially, this suggests that foot pressure patterns are comparable between healthy individuals and those with low back pain. The use of sensor-equipped inserts for pedobarographic examinations indicates that, in cases of degenerative changes in the lumbar and sacral spine without accompanying acute pain, gait patterns resemble those of the healthy population.

Salmonella Typhimurium is a typical Gram-Negative bacterium associated with food-borne illness threatening public health. This pathogen is reported to have caused millions of infections and thousands of hospitalizations yearly in the United States alone. Salmonella Typhimurium has a sophisticated array of virulent factors, including its flagella, which contributes significantly to its pathogenicity. Cannabidiol (CBD), the non-psychoactive component of the cannabis plant, has attracted the interest of many researchers recently because of its antimicrobial properties. With the growing interest in exploring CBD’s antimicrobial properties, we, in this study, have delved into unravelling how prolonged exposure of Salmonella Typhimurium to CBD influences the expression of the flgA gene. We hypothesized that the exposure of Salmonella Typhimurium to CBD may result in flgA upregulation, causing the bacteria to withstand various stresses and potentially enhance its survival rates and pathogenicity. We have employed several assays, such as mRNA expression, motility assays, pH induction assays, nutrient starvation interventions, and biofilm analysis, to explore the influence of CBD on the pathophysiology of Salmonella Typhimurium. Our findings reveal that CBD-resistant strains exhibit enhanced resilience to extreme pH levels and motility and survive poorly under nutrient starvation, with more robust biofilm formation compared to the susceptible strains. The results contribute to the broader comprehension of CBD resistance mechanisms in bacteria. This work provides insight into the potential therapeutic interventions for controlling CBD-resistant bacterial infections. This study also underscores the essence of exploring novel alternative antimicrobial agents to tackle the ever-persistence of bacterial antibiotic resistance.

The electronic properties of calcium intercalated graphite (CaC6) as a function of pressure are revisited using density functional theory (DFT). The electronic band structures of CaC6, like many other layered superconducting materials, display cosine-shaped bands at or near the Fermi level (FL). Such bands encompass bonding/antibonding information with a strong connection to superconducting properties. Using an hexagonal cell representation for CaC6, construction of a double supercell in the c-direction effects six-folding in reciprocal space of the full cosine function, explicitly revealing the bonding/antibonding relationship divide at the cosine midpoint. Similarly, folding of the Fermi surface (FS) reveals physical phenomena relevant to electronic topological transitions (ETT) with application of pressure. For CaC6, the peak value for the superconducting transition temperature, Tc, occurs at about 7.5 GPa, near to the observed pressure of the calculated ETT. At this pressure, the radius of the nearly spherical Ca 4s-orbital FS coincides with three times the distance from the G centre point to the Brillouin zone (BZ) boundary of the 2c supercell (which is equal to half the identically defined distance for the primitive rhombohedral BZ). In addition, the ETT coincides with alignment of the non-bonding (inflection) point of the cosine band (the point at which the sign of the cosine amplitude modulation is reversed) with the FL. At other calculated pressure conditions, the Ca 4s-orbital FS undergoes topological changes that correspond and can be correlated to experimentally determined changes in Tc. The ETT is a key mechanism that circumscribes the known significant drop in Tc for CaC6 as a function of increasing pressure.

Rebar quantity estimation is pivotal for determining the cost of construction projects and essential for bidding purposes. A bar bending schedule plays a crucial role by providing rebar information and bending instructions, facilitating efficient procurement. Traditional methods of bar bending schedules, which involve manual extraction from 2D (two-dimensional) drawings, are error-prone and hinder construction productivity. This study proposes a Building Information Modeling (BIM)-based algorithm that automates the generation of a Bar Bending Schedule (BBS) directly from the 3D (three-dimensional) BIM models, ensuring accuracy and eliminating manual errors. The effectiveness of the algorithm was verified by comparing the rebar quantities generated by the model against those derived from optimization calculations. The results demonstrated a mean absolute error of 0.017 and a mean absolute percentage error of 1.13%, validating the algorithm’s precision. Additionally, it achieved a remarkable 33.33% reduction in the manpower required for preparing BBSs, highlighting its potential to revolutionize construction workflow efficiency and accuracy.

Performance of the overhead squat may affect golf swing mechanics associated with golf-related low back pain. This study investigates the difference in lumbar kinematics and joint loads during the golf downswing between golfers with different overhead squat abilities. Based on the per-formance of the overhead squat test, 21 golfers aged 18 to 30 years were divided into the highest-scoring group (HS, N=10, 1.61 ± 0.05 cm, and 68.06 ± 13.67 kg) and lowest-scoring group (LS, N=11, 1.68 ± 0.10 cm, and 75.00 ± 14.37 kg). Data collection used a motion analysis system, two force plates, and TrackMan. OpenSim software was used to simulate the joint loads for each lum-bar joint. An independent t-test was used for statistical analysis. Compared to golfers demonstrat-ing limitations in the overhead squat test, golfers with better performance in the overhead squat test demonstrated significantly greater angular extension displacement on the sagittal plane, smaller lumbar extension angular velocity, and smaller L4-S1 joint shear force. Consequently, the overhead squat test is found to be a useful index to reflect lumbar kinematics and joint loading patterns during the downswing, and provides a good training guide reference for reducing the risk of a golf-related low back injury

A major problem of the technological production process of the metallurgical-grade silicon is formation of a large amount of microsilica. However, this material can be a significant source of raw materials for its own production. Hence, this study is aimed to solve the problem of micro-silica utilization, i.e. the technogenic dust-like waste generated during the melting of the technical-grade silicon. Within this study, the technology of the joint briquetting of microsilica was investigated with the carbonaceous reducing agents, i.e. by obtaining of mono-charge and by melting of the technical-grade silicon from the obtained mono-charge in the 200kVA ore-thermal furnace. Results of the study show that the briquettes in the melting process of the technical-grade silicon can be used in the range from 0 to 50%. The using of briquettes may significantly improve the technological parameters. When briquetted charge is applied only, the technological parameters will deteriorate significantly. The material balance of silicon melting showed the recovery rates of the main elements (Si, Al, Ca and Fe). It recorded a decrease in content of aluminum from 1.9-2.1% to 0.5-0.7%, calcium from 0.2-0.3% to 0.07-0.1% and titanium from 0.2-0.23% to 0.11-0.13% during the transition to briquetted monocharge. Phosphorus content increased from 0.004-0.005 to 0.011-0.013%.

Emphasizing the importance of acoustic attenuation in maintaining compliance with stringent noise regulations and enhancing workplace safety, the analysis covers the theoretical and practical aspects of sound attenuation in a turboengine testing stand. This paper presents a preliminary analysis and also an evaluation of a procedure for projecting a noise attenuator for industrial application and especially for turboengine test stands. While primarily focusing on the static acoustic behavior of the attenuator, considerations were also made regarding flow dynamics, Mach number-dependent attenuation, pressure drop, and self-generated noise aspects to provide a comprehensive perspective in selecting the optimal design configuration. The study investigates different calculation methods for assessment of the noise reduction for linear and staggered baffles, applied on a scaled reduced model of attenuator. Thus, the critical parameters and projecting requirements necessary for effective noise reduction in high-performance turboengine testing environments will be evaluated in a down-scaled model. Key factors examined include the selection of design parameters and configurations from various options. Advanced computational methods, like analytic and finite element analysis (FEM) are utilized to predict the acoustic performance and identify potential design optimizations. Experimental validation is performed to corroborate the simulation results, ensuring the reliability and efficiency of the attenuator. The findings indicate that a well-designed sound attenuator module can significantly reduce noise levels without compromising the operational performance of the turboengine inside a test cell.

This work studies a novel low voltage (<60 V) hybrid system that supports engine boosting and downsizing in addition to start-stop, regenerative braking, and constrained torque assist/regeneration. The hybrid power split supercharger (PSS) shares a 9 kW motor between supercharging the engine or providing hybrid functionalities through a planetary gear set, a brake and a bypass valve. The PSS operation is limited to only one of the parallel hybrid or boosting modes at a time, necessitating a highly optimized decision making algorithm to select the device mode and power split ratio. In this work an adaptive equivalent consumption minimization strategy (A-ECMS) is developed for energy management of the PSS. The A-ECMS effectiveness is compared against a dynamic programming (DP) solution with full drive cycle preview through hardware-in-the-loop experiments on an engine dynamometer testbed. The experiments show that the PSS with A-ECMS reduces a vehicle fuel consumption by 18.4% over standard FTP75 cycle compared to a baseline turbocharged engine, while global optimal DP solution decreases the fuel consumption by 22.8% compared to baseline.

Tack is one of the most important factors affecting the operability of prepregs, but it is still very difficult to obtain the change of prepreg tack with time at different temperatures. In this paper, a newly designed T-peel device is used to test the tack decay rate of prepregs at different temperatures. The obtained decay rate deviates less than 8.9% from the manufacturer's data. The maximum deviation of the ratio of tack decay speeds calculated by the Arrhenius equation from the experiments is not higher than -9.7%. It is proved that the present method can obtain the decay rate of tack of prepregs at different temperatures. This method is also applicable to the other two types of prepregs. The article proposes the handling life unit, an operational life measurement unit for prepregs, and establishes that the relationship between tack and remaining shelf life reduces prepreg management costs.

Background: Several kinds of research say that adjuvant blood glucose and blood pressure are usual, but an efficient solution for medical application count remains. This review analyzes the pandemic blood pressure and blood glucose to identify the publications which tell about the clinical practices and research gaps in systematic research.Methods: A study guides to identify the research of Blood Pressure (BP) and Blood Glucose. In order to analyze the recent innovations and research on BP and Blood glucose, the relevant publications and literature from journals were identified.Results: Co-morbidity of BP and Blood glucose is reported as very high. The commonness of blood pressure is thrice as high in type I diabetes patients and almost two times higher in type II diabetes patients when compared to others without Diabetes. The pervasiveness of getting depression is more in the female when compared with men. A detailed study about the linkage of BP and blood glucose tells that the relationship between them is not exactly clear.Limitations: Nearly all reviews providing the linkage of BP and blood glucose are with some limitations and they are not providing any clear conclusion.Conclusions: Present research tells that people having high blood glucose will have a greater chance of getting high blood pressure. More research is needed to state the linkage between BP, blood glucose, and the growth of diabetes mellitus issues and to provide support for managing Diabetes.

Cyclic vomiting syndrome (CVS) is a frequently disabling condition defined by severe, discrete, stereotypical episodes of nausea and vomiting. In our previous report [1], a candidate gene list was evaluated in a group of 80 unrelated participants with CVS with extensive genetic sequencing (whole exome/genome). Twenty-two good candidate genes for CVS association were identified, from which a cellular model of aberrant cation transport and energy metabolism was proposed. Herein, we present additional clinical information on those 80 participants, including eight case reports to highlight general principles and clinical practices. Our participants demonstrate substantial phenotypic and genotypic heterogeneity in CVS, including a propensity for specific co-morbidities in the participants and relatives, evolution towards episodes in which vomiting is less apparent, labeling with “non-organic” diagnoses, multiple genes, polygenic inheritance, and association with variants not designated as Pathogenic. Our case reports illustrate how genetic information can guide clinical management and argue to the high clinical utility of appropriate genetic testing and analysis in CVS. Expression profiling of our 22 candidate genes suggests an anatomical model in a unit defined by vagal afferents and adjacent cells. Our models are consistent with multiple current hypotheses of CVS and the efficacy of commonly-recommended treatments.

Ice-binding proteins (IBPs) have several functions that permit their hosts to thrive in the presence of ice. The ability of IBPs to control ice growth makes them potential additives in various industries ranging from food storage and cryopreservation to anti-icing systems. For IBPs to be used in commercial applications, however, methods are needed to produce sufficient quantities of high-quality proteins. Here, we describe a new method for IBP purification, termed falling water ice purification (FWIP). The method is based on the affinity of IBPs for ice. A crude IBP solution is allowed to flow continuously over the large chilled vertical surface of a commercial ice machine. The temperature of the surface is lowered gradually until ice crystals are produced, to which the IBPs bind but other solutes do not. As in other ice affinity methods, FWIP does not require molecular tags and is suitable for purifying recombinant IBPs as well as IBPs from natural sources. The advantage of FWIP over other ice affinity methods is that it exploits an ice machine designed to produce large volumes of clear ice daily. This system can be easily scaled up and suits the purification of industrial quantities of IBPs. The FWIP method significantly advances the use of IBPs in research and industry.

In this data deposit, I describe a dataset that is the result of content mining 167,318 published articles for statistical test results. As a result of this content mining, 688,112 results from 50,845 articles were extracted. In order to provide a comprehensive set of data, the statistical results are supplemented with metadata from the article they originate from. The dataset is provided in a comma separated file (CSV) in long-format. For each of the 688,112 results, 20 variables are included, of which seven are article metadata and 13 pertain to the individual statistical results (e.g., reported and recalculated p-value). A five-pronged approach was taken to generate the dataset: (i) collect journal lists, (ii) spider journal pages for articles, (iii) download articles, (iv) add article metadata, and (v) mine articles for statistical results.

The demonstration of compliance of rolling stock against disturbance limits for railway signaling, and in particular track circuits, is subject to a large deal of variability, caused by the diverse values of the electrical parameters of the railway line and resulting transfer functions, as well as operating conditions of rolling stock during tests. Instrumental uncertainty is evaluated with a Type B approach and shown to be much less than the experimental variability. Repeated test runs in acceleration, coasting, cruising, braking conditions are considered, deriving both max-hold (spread) and sample dispersion curves compared to the respective mean values (Type A approach to the evaluation of uncertainty). The major source of variability affecting a significant portion of the spectrum is caused by the superposed oscillations of the onboard LC filter, for which different choices of the transformation window duration are discussed. The test runs and the acquired data covered overall 1 day of tests along about 300 km of the Italian 3 kV DC railway network.

The zinc oxide (ZnO) arrester is positioned on locomotive roof preventing other onboard electrical equipment from the harm caused by external and internal overvoltages. A number of locomotive arrester burnout and explosion accidents occur during traction supply network harmonic resonance causing train stoppages and power outages in the network. This study firstly carries out high-frequency tests to investigate the wide frequency band electrical characteristics of the locomotive arrester, explaining that the arrester is prone to fault during resonance. Consequently, a prognostics and health management (PHM) for locomotive arrester is proposed providing on online monitoring, fault warning and health assessment solutions, which is beneficial to the operation and maintenance of arresters in the future. The testing method and PHM scheme presented in this paper can be not only applied to the arrester, also readily expanded to other high-voltage electrical equipment on the electric locomotive.

Autism spectrum disorder (ASD) is a common condition with lifelong implications. The last decade has seen dramatic improvements in DNA sequencing and related bioinformatics and databases. We analyzed the raw DNA sequencing files on the Variantyx® bioinformatics platform for the last 50 ASD patients evaluated with trio whole genome sequencing (trio-WGS). “Qualified” variants were defined as coding, rare, and evolutionarily conserved. Primary Diagnostic Variants (PDV) additionally were in genes directly linked to ASD and matched clinical correlation. A PDV was identified in 34/50 (68%) of cases, including 25 (50%) cases with heterozygous de novo and 10 (20%) with inherited variants. De novo variants in genes directly associated with ASD were far more likely to be Qualifying than non-Qualifying versus a control group of genes (P=0.0002), validating that most are indeed disease related. Sequence reanalysis increased diagnostic yield from 28% to 68%, mostly by inclusion of de novo PDVs in genes not yet reported as ASD associated. Thirty-three subjects (66%) had treatment recommendation(s) based on DNA analyses. Our results demonstrate high yield of trio-WGS for revealing molecular diagnoses in ASD that is greatly enhanced by re-analyzing DNA sequencing files. In contrast to previous reports, de novo variants dominate the findings, mostly representing novel conditions. This has implications to the cause and rising prevalence of autism.

Conditional Independence (CI) testing is fundamental in statistical analysis. For example, CI testing helps validate causal graphs or longitudinal data analysis with repeated measures in causal inference. CI testing is difficult, especially when testing involves categorical variables conditioned on a mixture of continuous and categorical variables. Current parametric and non-parametric testing methods designed for continuous variables and can quickly fall short in the categorical case. This paper presents a computational approach for CI testing for categorical data types, which we call computational conditional independence (CCI) testing. The test procedure is based on permutation and combines machine learning prediction algorithms and Monte Carlo Cross-Validation. We evaluated the approach through simulation studies and assessed the performance against alternative methods; the generalized covariance measure (GCM) test, the kernel conditional independence (KCI) test, and testing with multinomial regression. We find that the computational approach to testing has utility over the alternative methods, and we can achieve better control over type-I-error rates. We hope this work can expand the toolkit for CI testing for practitioners and researchers.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

Abstract Objectives: Aging may challenge life and even affect individuals' well-being and flourishing. This includes challenges of shrinking social relations and being by yourself in old age while using your personal strengths. The current study examines two important personal resources, i.e., the skill of positive solitude and the 24 character-strengths, that may be associated with flourishing in old age. Methods: A convenience sample of 1085 community-dwelling adults (M = 57.20, SD = 6.24, range = 50-87), completed an online self-report survey with demographic measures and scales measuring personal strengths, the skill of positive solitude, and flourishing. Results: As hypothesized, the 24 character-strengths and positive solitude, were each associated with flourishing, and positive solitude moderated the relationships between the 24 character-strengths and flourishing. The 24 character-strengths and flourishing relationship was stronger among participants with lower levels of positive solitude. Conclusion: These findings highlight that despite the decrease in social relations which often characterizes old age, the skill of positive solitude serves as a valuable resource for flourishing in the later stages of life.

This paper has the objective of implementing the radial rotor position control of a three-phase bearingless induction machine with split winding and optimized drive structure, using the ADRC technique. Because it is a multivariable, nonlinear, time-varying system with coupled variables, it is necessary to use advanced control strategies in order for the system to operate efficiently and with good dynamic performance. The ADRC controller considers the total disturbance composed of unmodeled dynamics, nonlinearities, uncertainties, and load variations, as a new system state, to be estimated in real-time through an extended state observer. In this mode, disturbances are compensated in real-time, eliminating regime errors and with good response to disturbances in general.

The study of pain requires a balance between subjective methods that rely on self-reports and complementary objective biometrics that ascertain physical signals associated with subjective accounts. There are at present no objective scales that enable the personalized assessment of pain, as most work involving electrophysiology rely on summary statistics from a priori theoretical population assumptions. Along these lines, recent work has provided evidence of differences in pain sensations between participants with Sensory Over Responsivity (SOR) and controls. While these analyses are useful to understand pain across groups, there remains a need to quantify individual differences more precisely in a personalized manner. Here we offer new methods to characterize pain using the moment-by-moment standardized fluctuations in EEG brain activity centrally reflecting the person’s experiencing temperature-based stimulation at the periphery. This type of gross data is often disregarded as noise, yet here we show its utility to characterize the lingering sensation of discomfort raising to the level of pain, individually, for each participant. We show fundamental differences between the SOR group in relation to controls and provide an objective account of pain congruent with the subjective self-reported data. This offers the potential to build a standardized scale useful to profile pain levels in a personalized manner across the general population.

Fungi inhabiting deep subseafloor sediments have been shown to possess anaerobic methane (CH₄) production capabilities under atmospheric conditions. However, their ability to produce CH₄ under in situ conditions with high hydrostatic pressure (HHP) remains unclear. Here, Schizophyllum commune 20R-7-F01, isolated from ~ 2 km below the seafloor, was cultured in Seawater Medium (SM) in culture bottles fitted with sterile syringes for pressure equilibration. Subsequently, these culture bottles were transferred into 1-liter stainless steel pressure vessels at 30 °C for 5 days to simulate in situ HHP and anaerobic environments. Our comprehensive analysis of bioactivity, biomass, transcriptomics revealed that S. commune not only survived but significantly enhanced CH₄ production, reaching approximately 2.5 times higher levels under 35 MPa HHP compared to 0.1 MPa standard atmospheric pressure. Pathways associated with carbohydrate metabolism, methylation, hydrolase activity, cysteine and methionine metabolism, and oxidoreductase activity were notably activated under HHP. Specifically, key genes involved in fungal anaerobic CH₄ synthesis, including methyltransferase mct1 and dehalogenase dh3, were upregulated 7.9- and 12.5-fold, respectively, under HHP. Enhanced CH₄ production under HHP was primarily attributed to oxidative stress induced by pressure, supported by intracellular Reactive Oxygen Species (ROS) levels and comparative treatments with cadmium chloride and hydrogen peroxide. These findings suggest that fungi persisting in deep-sea sediments over millions of years have the potential to significantly contribute to global CH₄ flux.

This research aims to study the ultimate limit state (ULS) behaviour of stiffened panel under longitudinal compression by non-linear finite element method (NLFEM). There are different types of stiffeners being used in shipbuilding i.e. T-bar, flat-bar and angle-bar. However, this research focuses on the ultimate compressive strength behaviour of flat-bar stiffened panel. A total of 420 of reliable scenarios of flat-bar stiffened panel are selected for numerical simulation by ANSYS NLFEM. The ultimate strength behaviours obtained were used as data for the development of closed form shape empirical formulation. Recently, Kim et al. [1] proposed for advanced empirical formulation for T-bar stiffened panel and the applicability of the proposed formulation to flat-bar stiffened panel will be confirmed by this study. The accuracy of the empirical formulation obtained for flat-bar stiffened panel has been validated by FE simulation results of statistical analysis (R2 = 0.9435). The outcome obtained will be useful for ship structural designers in predicting the ultimate strength performance of flat-bar type stiffened panel under longitudinal compression.

Clarifying the distribution of temperature and pressure in the wellbore and cavern during hydrogen injection and extraction is crucial for quantitatively assessing cavern stability and wellbore integrity. This paper establishes an integrated flow and heat transfer model for the cavern and wellbore during hydrogen injection and production, analyzing the variations in temperature and pressure in both the wellbore and the cavern. The specific conclusions are as follows. (1) The temperature and pressure parameters of hydrogen and natural gas within the chamber and wellbore were compared. Under identical injection and production conditions, the temperature of hydrogen in the chamber was 10°C higher than that of natural gas, and 16°C higher in the wellbore. The pressure of hydrogen in the chamber was 2.9 MPa greater than that of natural gas, and 2.6 MPa higher in the wellbore. (2) A comparative analysis was conducted on the impact of surrounding rock’s horizontal and numerical distance on temperature during hydrogen and natural gas injection processes. As the distance from the cavity increases, from 5 to 15 meters, the temperature fluctuation in the surrounding rock diminishes progressively, with the temperature effect in the hydrogen storage chamber extending at least 10 meters. (3) The influence of rock thermal conductivity parameters on temperature during the processes of hydrogen injection and natural gas extraction is compared. The better the thermal conductivity, the deeper the thermal effects penetrate the rock layers, with the specific heat capacity having the most significant impact.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Background: This study stands as a pioneer in the histological evaluation of the biological behavior of a novel implant design featuring decompressive cervical blades. Hence, the aim of the present study was to evaluate the healing outcome in cortical regions at where decompressive protocols were adopted using implants equipped with blades. Materials and methods: Blades with varying diameters were integrated into the coronal portion of the implant to prepare the cortical region of rabbit tibiae. The blade diameters differed from the implant collar by the following amounts: control group (0 µm), +50 µm, and +200 µm. Results: No marginal bone loss was detected. Instead, all implants exhibited new bone formation in the coronal region. Complete closure was observed in the CG-0 group, as well as in the TG-50 and TG-200 groups, despite the presence of marginal gaps without primary bone contact at installation. In the apical region, most implants breached the cortical layer. Nevertheless, new bone formation in this region completely closed the osteotomy, effectively isolating the internal environment of the tibia from the external. Conclusions: The use of a blade attached to the implant body enabled precise preparation of the cortical layer, allowing for controlled decompression in the targeted area. This technique resulted in optimal osseointegration with no loss of marginal bone, and complete restoration of marginal gaps ranging from 0 µm to 200 µm.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

Atmospheric pressure Microplasma is a simple, cost-effective, efficient, and eco-friendly procedure, which is superior to the traditional nanomaterials synthesis techniques. It generates high yields and allows for a controlled growth rate and morphology of nanomaterials. The silver (Ag) nanomaterials, with their unique physical and chemical properties, exhibit outstanding antibacterial and anti-fungal properties. Similarly, zinc oxide (ZnO) nanomaterials, known for their low toxicity and relatively lower cost, find wide applications in wound repair, bone healing, and antibacterial and anticancer applications. The use of core-shell nanomaterials in certain situations where some nanoparticles can cause serious harm to host tissues or organs is a testament to their potential. A benign material is coated over the core to reduce toxicity in these cases. This review compares the numerous configurations of microplasma systems used for synthesizing nanomaterials and their use in producing Ag, ZnO, and their core-shell (Ag-ZnO) nanomaterials for biomedical applications. The summary also includes the effect of control parameters, including cathode diameter, gas flow rate, precursor concentration, voltage, and current, on the nanomaterial's characteristics and applications. In addition, it provides a research gap in the synthesis of Ag, ZnO, and core shall nanomaterials by this technique, as well as the development and limitations of this technique and the use of these nanoparticles for biomedical applications.

Background: The skin prick test (SPT) is used to diagnose sensitization to antigens. This study proposes a deep learning approach to infer wheal dimensions, aiming to reduce dependence on human interpretation. Methods: A dataset of SPT images (n=5844) was used to infer a convolutional neural network for wheal segmentation (ML model). Three methods for inferring wheal dimensions were evaluated: the ML model; the standard protocol (MA1); and approximation of the area as an ellipse using diameters measured by an allergist (MA2). The results were compared with assisted image segmentation (AIS), the most accurate method. Bland-Altman, distribution analyses, and correlation tests were applied to compare the methods. The study also compared the percentage deviation among these methods in determining the area of wheals with regular geometric shapes (n = 150) and with irregular shapes (n=150). Results: The Bland-Altman analysis showed that the difference between methods was not correlated with the absolute area. The ML model achieved a segmentation accuracy of 85.88% and a strong correlation with the AIS method (ρ=0.88), outperforming all other methods. Additionally, MA1 showed significant error (13.44±13.95%) for pseudopods. Conclusions: The ML protocol can potentially automate the reading of SPT, offering greater accuracy than the standard protocol.

Flexible wearable pressure sensors offer numerous benefits, including superior sensing capabilities, a lightweight and compact design, and exceptional conformal properties, making them highly sought after in various applications including medical monitoring, human-computer interaction, and electronic skin. Because of their excellent characteristics, such as simple fabrication, low power consumption, and short response time, capacitive pressure sensors have received widespread attention. As a flexible polymer material, polydimethylsiloxane (PDMS) is widely used in the preparation of dielectric layers for capacitive pressure sensors. The Young's modulus of the flexible polymer can be effectively decreased through the synergistic application of sacrificial template and laser ablation techniques, thereby improving the functionality of capacitive pressure sensors. In this study, a novel sensor was developed through a series of processes including sacrificial template method using NaCl microparticles, CO₂ laser ablation, and sandwiching a porous PDMS dielectric layer between two flexible electrodes to create a capacitive pressure sensor. The sensor demonstrates a sensitivity of 0.694 kPa-1 within the pressure range of 0-1 kPa, and can effectively detect pressures ranging from 3 Pa to 200 kPa. The sensor demonstrates stability for up to 500 cycles, with a rapid response time of 96ms and a recovery time of 118ms, coupled with a low hysteresis of 6.8%. Furthermore, our testing indicates that the sensor possesses limitless potential for use in detecting human physiological activities and signaling emergencies.

Currently, for the serious air pollution and global warming effect caused by the substance released from the present vehicle, it is expected that the regulatory requirements for the emission will become more stringent. A new concept of the combustion technology that can reduce the NOx and PM related to combustion is urgently needed. To cope with such social demands, many developed countries are efforts to develop the environment friendly vehicle engine at the national lever in order to satisfy with strengthening emission control. As a main combustion technology among new combustion technology for the new generation engine, the homogenous charge compression engine (HCCI) is expanding its application range by employing multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. In this paper, a multi-injection method in order to apply the HCCI combustion method without mainly altering engine specifications and practicality by referring to the results of the HCCI engine was investigated. Applied with forced charging, exhaust gas recirculation (EGR) and compression ratio change, it was evaluated to the possibility of securing optimum fuel economy and emission reduction in the IMEP 0.8 MPa range.

Background: A Morel–Lavallée lesion (MLL) is a traumatic, internal closed degloving injury that results from shearing of subcutaneous tissue away from underlying fascia, usually associated with high-velocity trauma. Case presentation: A 52-year-old man was transported to hospital for further follow-up of a superficial femoral artery injury. Examination on admission showed bruising seen around the left thigh. Contrast-enhanced computed tomography of the left thigh revealed hematoma with extravasation from a branch of the left superficial femoral artery, but no apparent aneurysms or femoral fractures. The patient was treated with compression bandages and discharged on hospital day 6. He left hospital able to walk unaided. He subsequently complained of left thigh pain with swelling and visited the hospital several times. He was treated at another outpatient clinic and was diagnosed with MLL. Single-use disposable portable negative pressure wound therapy (NPWT) was applied for about 2 months, achieving a stable wound site. Conclusion: We encountered a case of MLL successfully treated with single-use portable NPWT. This report presents the case of a patient with isolated MLL without fracture in the left thigh, in which the diagnosis was missed on initial admission. Finally, the patient received minor interventions including drainage along with tissue debridement and portable NPWT. We reviewed the relevant literature and summarize the pathogenesis, clinical manifestations, and treatment strategies for MLL. Emergency physicians require an increased understanding of MLL to avoid misdiagnosis and missed diagnosis.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

This study simulated the effects of direct predatory pressure, indirect predatory pressure, and conspecific injury signals on the sea cucumber (Apostichopus japonicus) to determine changes in the activity of immune defense enzymes (lysozyme, acid phosphatase, alkaline phosphatase) and antioxidant stress enzymes (catalase, superoxide dismutase, malondialdehyde). Samples of sea cucumber juveniles were collected at 3 hours, 12 hours, 72 hours, and 96 hours post-predatory stress, and six enzymes related to immune defense and antioxidant stress were selected for activity assays, namely lysozyme (LZM), acid phosphatase (ACP), alkaline phosphatase (AKP), superoxide dismutase (SOD), catalase (CAT), and malondialdehyde (MDA). The results indicated that under direct predatory pressure, the activity of catalase in sea cucumbers was significantly higher than that of the control group at 3 hours (P < 0.05), while the activities of acid phosphatase, alkaline phosphatase, and catalase were significantly lower at 72 hours (P < 0.05). Under indirect predatory pressure, the activity of malondialdehyde in sea cucumbers was significantly higher than that of the control group at 12 hours (P < 0.05), the activity of alkaline phosphatase was significantly higher at 72 and 96 hours (P < 0.05), catalase was significantly lower at 72 hours, and the activity of superoxide dismutase was significantly higher at 72 hours (P < 0.05). Under the influence of conspecific injury signals, the activity of malondialdehyde in sea cucumbers was significantly higher than that of the control group at 12 hours (P < 0.05), and the activity of superoxide dismutase was significantly higher at 96 hours (P < 0.05). The sea cucumber enhanced its antioxidant capacity 3 hours after facing the predator, while its immune defense mechanism was suppressed at 72 hours. When facing indirect predatory pressure, the sea cucumber may have made immune and antioxidant preparations for the arrival of unknown risks. The experimental results show that predatory pressure has a significant impact on the immune and antioxidant functions of sea cucumbers, which may be related to the physiological state and environmental adaptability of the sea cucumber. This study provides a new perspective for understanding how sea cucumbers cope with predatory pressure in the natural environment and offers theoretical support for the cultivation management of sea cucumbers.

In current transportation hubs, it is a common phenomenon that passengers travel with necessary wheeled-luggage or suitcases. Due to the fact that most luggage occupies certain space within dense passenger crowds with giant mass inertia, its abnormal motions, such as drifting, frequently trig unavoidable local disturbances and turbulence in surrounding pedestrian flows, further increasing security risk. While, current researches primarily concentrate on examining the impact of luggage on crowd evacuation efficiency through scenario-based experiments and analyzing the spatial characteristics of crowd distribution in surveillance videos. There still lacks of the dynamic disturbance mechanisms and crowd stability associated with the combined motion of passengers and luggage. Therefore, this study considers the luggage-laden passenger as a deformable particle, the resulting disturbance on surrounding non-luggage passengers is analyzed and quantified into a nonlinear pressure term. Subsequently, the disturbance propagation model of passenger-luggage is developed by adapting the classical Aw-Rascle traffic flow model with incorporation of the pressure term. Simulation experiments of disturbances caused by luggage drifting and retrograding validate that the proposed propagation model aligns with real-world situations in transportation hubs. Quantitively, when luggage-laden passenger drifted left, the disturbing force of left side crowd can reach a peak of 238N in the passenger density of 3.0 p/m2, and the maximum difference between the left and right sides disturbing force can reach 153N. Furthermore, it is recommended that the proposed model can be applied to crowd flow analysis and risk assessment.

An association between subtle changes in T2 white matter hyper-intense signals (WMHS) de-tected in fetal brain magnetic resonance imaging (fbMRI) and congenital cytomegalovirus (CMV) infection has been established. The research aim of this study is to compare children with congenital CMV infection with neurodevelopment outcome and hearing deficit with and with-out WMHS in a prospective historic cohort of 58 fbMRIs. Of these, WMHS was detected in 21. The median infection week of the WMHS group was earlier than the normal fbMRI group (8 and 17 weeks of gestation respectively). The proportion of infants treated with valganciclovir in the WMHS group was distinctly higher. Hearing impairment was not significantly different be-tween the groups. VABS scores in all 4 domains were within normal range in both groups. The median score of the motor skills corrected for week of infection was better in the WMHS group. A multivariate analysis using week of infection interaction variable of WMHS and valganciclo-vir treatment showed better motor score outcomes in the valganciclovir treatment group despite earlier week of infection. WMHS was not associated with neurodevelopmental outcome and hearing deficit. In our cohort valganciclovir treatment may have a protective effect on fetuses with WMHS by improving neurodevelopment outcome.

Cardiac autonomic neuropathy (CAN) is a severe complication of diabetes mellitus (DM) strongly linked to a nearly five-fold higher risk of cardiovascular mortality. Patients with Type 2 Diabetes Mellitus (T2DM) are a significant cohort in which these assessments have particular relevance to the increased cardiovascular risk inherent in the condition. This study aimed to explore the subtle correlation between the Ewing test, Sudoscan-cardiovascular autonomic neuropathy score, and cardiovascular risk calculated using SCORE 2 Diabetes in individuals with T2DM. The cohort consisted of 211 patients diagnosed with T2DM with overweight or obesity without established ASCVD, aged between 40 to 69 years. The prevalence of CAN in our group was 67.2%. In the study group, according SCORE2-Diabetes, four patients (1.9%) were classified with moderate cardiovascular risk, thirty-five (16.6%) with high risk, and one hundred seventy-two (81.5%) with very high cardiovascular risk. On multiple linear regression, the SCORE2-Diabetes algorithm remained significantly associated with Sudoscan CAN-score and Sudoscan Nephro-score and Ewing test score. Testing for the diagnosis of CAN in very high-risk patients should be performed because approximately 70% of them associate CAN. Increased cardiovascular risk is associated with sudomotor damage and that Sudoscan is an effective and non-invasive measure of identifying such risk.

Abstract: Wireless body area networks (WBANs) have strong potential in the field of health monitoring. However, the energy consumption required for accurate monitoring limits the time between battery charges of the wearable sensors, which is a key performance factor (and can be critical in the case of implantable devices). In this paper, we study the inherent trade-off between the power consumption of the sensors and the probability of misclassifying a patient’s health state. We formulate this trade-off as a dynamic problem, in which at each step we can choose to activate a subset of sensors that provide noisy measurements of the patient’s health state. We assume that the (unknown) health state follows a Markov chain, so our problem is formulated as a partially observable Markov decision problem (POMDP). We show that all the past measurements can be summarized as a belief state on the true health state of the patient, which allows tackling the POMDP problem as an MDP on the belief state. We then empirically study the performance of a greedy one-step look-ahead policy compared to the optimal policy obtained by solving the dynamic program. For that purpose, we use an open-source Continuous Glucose Monitoring (CGM) data set of 232 patients over six months and extract the transition matrix and sensor accuracies from the data. We find that the greedy policy saves ~50% of the energy costs while reducing the misclassification costs by less than 2% compared to the most accurate policy possible that always activates all sensors. Our sensitivity analysis reveals that the greedy policy remains nearly optimal across different cost parameters and a varying number of sensors. The results also have practical importance, because while the optimal policy is too complicated, a greedy one-step look-ahead policy can be easily implemented in WBAN systems.

Fastener holes are among the most common natural stress concentrators in metal structures. The life cycles of various structural elements, such as those in aircraft structures, automobiles, and rail-end bolt joints are limited by fatigue damage around the holes. An effective approach to delay the formation and growth of fatigue macrocracks is to introduce residual hoop compressive stresses around the holes. Two methods have become established in the prestressing of fastener holes in aircraft components: split sleeve and split mandrel, which implement one-sided processes. The common disadvantage of both methods is the complex procedure due to the need for high accuracy of the initial holes. This article presents a new modified split mandrel method providing the same tightness (interference fit) with a wide tolerance of the pre-drilled hole diameters reducing the number of technological cycle steps and production costs. То implement the new method, a functionally connected tool and a device with a hydraulic drive were developed. An extensive experimental study of 2024-T3 AA specimens was carried out to evaluate the effectiveness of the method under a high scattering of the pre-drilled holes. The new method provided a deep zone of residual hoop compressive stresses on both faces of the specimens after cold working and after hole final reaming. The removal of a plastically deformed layer around the hole of suitable thickness during the final reaming decreased the axial gradient of residual hoop stress distribution. Fatigue tests on a tensile pulsating cycle verified the effectiveness of the modified split mandrel method to significantly increase the fatigue life by 6.6 times based on cycle fatigue strength compared to the conventional case of machining the holes. The obtained S-N curves for three groups of samples with initial hole diameters of 8.0, 8.1, and 8.2 mm which were cold worked with the same tightness of 0.32 mm and final reamed, aligned well indicating that the new method can provide constant fatigue strength for a given stress amplitude.

The aim of this work is to propose two different and complementary sensors for the structural health monitoring of concrete beams. In particular, a diffused sensing element and a split ring resonator network are presented. The first sensor is able to detect the variation of the dielectric properties of the concrete along the whole beam length, for a diffuse monitoring both during the important concrete curing phase and also for the entire life cycle of the concrete beams. The resonators instead work punctually, in their surroundings, allowing an accurate evaluation of the permittivity both during the drying phase and after. This allows the continuous monitoring of any presence of water both inside the concrete beam and in points that can be critical, in the case of beams in dams, bridges or in any case subject to a strong presence of water which could lead to deterioration, or worse, cause serious accidents. Moreover, the punctual sensors are able to detect the presence of cracks in the structure and to localize them.

Monitoring crown closure evolution using multi-temporal Light Detection and Ranging (LiDAR) surveys is a method that we expect to be increasingly adopted given the availability of LiDAR sensors and the accumulating survey archives. However, little attention was devoted to comparing crown closure estimates from independent surveys. Although survey parameters cannot be modified after the data collection, we speculate that the error associated to crown closure estimates comparison can be reduced by selecting optimal post-survey parameters. In this study, we compared crown closure estimates of three airborne LiDAR surveys from 2018 (40 pt/m²) used as a reference, and two lower-density surveys from 2016 (4.5 pt/m²) and 2018 (2 pt/m²). We studied the effect of the height threshold used to separate canopy points and the grid resolution, using skewness and variance of lagged difference of crown closure. Crown closure estimates using low height thresholds were more different across surveys, resulting in higher root mean squared error (RMSE), bias and more different variograms. Results show that optimal height threshold was 3 m and grid resolution was 25 m, although there was room for decision (RMSE of 7% and 5%, and bias of 4% and 0% for 2016 and 2018 low-density surveys).

Tamil Nadu, a state in southern India, is bereft of any native milch or dual-purpose cattle breed and the state depends chiefly on crossbred cattle for milk production. As most (90 percent) of the milk production in the state was contributed by Jersey crossbred cattle, the genetic evaluation study was intended to assess the milk production traits viz., test-day milk yields (TDMYs), total milk yield (TMY) and 305-day milk yield (305MY) in these crossbred cattle reared under farmers’ rearing environment. Data on monthly TDMYs (TDMY1 to TDMY10) of Jersey crossbred cows (n=81,653) reared by the farmers over 24 years (1999-2022) were collected for evaluation. The influence of non-genetic factors viz., location (agroclimatic zones), period and season of calving, and parity on TDMYs, TMY, and 305MY were assessed, and the variance and covariance components for genetic parameters (heritability and genetic correlation) of the traits were estimated by the method of restricted maximum likelihood (REML) under multivariate animal model and by random regression model (RRM). The overall means of various TDMYs ranged from 4.98 (TDMY10) to 9.95 kg (TDMY2) and, for TMY and 305MY the means were 2480.33 and 2393.71 kg respectively. The heritabilities estimated by animal model for TDMYs were high and ranged from 0.39 ± 0.01 to 0.47 ± 0.01 and were fairly less variable throughout the lactation while the estimates obtained by RRM were medium to high and ranged between 0.28 ± 0.01 and 0.65 ± 0.02 for different days in milk (DIMs). The heritability estimated for TMY and 305MY were 0.48 ± 0.01 and 0.49 ± 0.01 respectively. The estimates of heritability in mid-lactation yields were comparatively little less than those at the beginning and the end of lactation. The high estimates of heritabilities for TDMYs, TMY, and 305MY obtained in the present study offered an ample scope for improving milk production through selective breeding. Genetic correlations between TDMYs estimated by animal model were positive and moderate to high, with a range between 0.47 ± 0.01 and 0.99 ± 0.00. Considerably higher estimates (0.97-0.99) were observed between adjacent TDMYs showing strong genetic associations. By RRM, genetic correlations estimated between DIMs were positive, except for a few estimates and the magnitude of genetic correlation decreased with an increase in the interval between the DIMs. The high genetic correlation observed between the TDMYs in early and mid stages of lactation with TMY and 305MY suggested that these test day yields could be used favorably for the early selection of cows for milk production which facilitates reduction in the generation interval and consequently increase the annual genetic gain for the milk production traits.

Rett syndrome (RTT) is an X-linked neurodevelopment disorder associated with the single monogenic mutation in methyl-CpG binding protein 2 (MeCP2) in up to 95% of cases. The growing number of genome-wide association studies and incomplete concordance for autoimmune diseases in monozygotic twins concur to support the involvement of environmental factors, like infectious agents or chemicals, in the breakdown of tolerance leading to autoimmunity. In fact, the coexistence of a perturbation of the immune system in RTT patients has been previously hypothesized. We herein explored the hypothesis that an autoimmune component derived from environmental bacterial infection of non typeable Haemophilus influenzae may coexist in RTT. At this purpose we screened sera from RTT syndrome patients, non-RTT pervasive developmental disorders patients and healthy controls with the hyperglucosylated adhesin protein HMW1ct(Glc) used as a precise antigen in ELISA in order to identify specific antibodies to N-glucosylation sites. Results showed that HMW1ct(Glc) is able to significantly discriminate antibodies among RTT sera and controls. Competitive ELISA confirmed the specific interaction between antibodies characteristic of RTT syndrome and the N-glucosylation motifs of the bacterial adhesin protein HMW1ct(Glc).

Anaerobic digestion has the potential to convert organic waste materials into valuable energy. At the same time, using press water from biomass materials for energy generation, while taking advantage of the resulting cake for other purposes is an emerging approach. Therefore, this study aimed to investigate the residual potential expected from a typical biogas feedstock in the West African context after it has been mechanically separated into liquid and solid phases. Hence, in this study, the rumen contents of ruminants (cow, goat and sheep) and their proportionate ratios were obtained from an abattoir in Ghana. Resource characterisation of the waste samples were carried out in the Central laboratory of the HFR, Germany. Anaerobic batch tests for biogas (biomethane) yield determination were set-up using the Hohenheim Biogas Yield Test (HBT). Inoculum used was obtained from an inoculum production unit at the Hohenheim University biogas laboratory. The trial involved two different forms of the sample: mixture of rumen contents, press water, and inoculum, each in four (4) replicates. The trial was carried out at a mesophilic temperature of 37°C. Results obtained over a seventy (70) day period were transformed into biogas yields. Overall, the results show that the current contents are suitable for biogas generation as an option, as opposed to the current form of disposal at a refuse dump. However, using these mixtures in their original forms is more technically viable than using press water without further treatment.