In response to a perceived epidemic of coronary heart disease, Ancel Keys introduced the lipid-heart hypothesis in 1953 which asserted that high intakes of total fat, saturated fat, and cholesterol lead to atherosclerosis and that consuming less fat and cholesterol, and replacing saturated fat with polyunsaturated fat, would reduce serum cholesterol and consequently the risk of heart disease. Keys proposed an equation that would predict the concentration of serum cholesterol (DChol.) from consumption of saturated fat (DS), polyunsaturated fat (DP), and cholesterol (DZ): ΔChol. = 1.2(2ΔS − ΔP) + 1.5ΔZ. However, the Keys equation conflated natural saturated fat and industrial trans-fat into a single parameter and considered only linoleic acid as the polyunsaturated fat. This ignored the widespread consumption of trans-fat and its effects on serum cholesterol and promoted an imbalance of omega-6 to omega-3 fatty acids in the diet. Numerous observational, epidemiological, interventional, and autopsy studies have failed to validate the Keys equation and the lipid-heart hypothesis. Nevertheless, these have been the cornerstone of national and international dietary guidelines which have focused disproportionately on heart disease and much less so on cancer and metabolic disorders, which have steadily increased since the adoption of this hypothesis.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

This paper attempts to propose a Riemann spring model via an analogy between the Riemann Zeta function of a complex number and the elastic spring in series.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

Cirina forda caterpillars are a significant protein source in Central Africa, yet their preservation and consumption pose challenges. This study investigates the drying of Cirina forda caterpillars to enhance preservation methods and product quality. Caterpillars were subjected to drying experiments at temperatures ranging from 40°C to 70°C, using tunnel and oven dryers. The drying kinetics was analyzed using mathematical models, revealing a water diffusion-limited mechanism in all the tested conditions. The Newton model provided adequate estimations of the drying behavior, facilitating further practical dryer design. Shrinkage analysis indicated a two-step process independent of the drying conditions. Achieving a moisture content suitable for prolonged storage resulted in substantial volume loss, highlighting the challenges of preserving dried caterpillars. These findings shed light on how to optimize drying processes for Cirina forda caterpillars, crucial for sustaining protein sources in Central Africa.

Climate change, growing world population and increasing food demand require higher yields and adaptability of crops, including spring bread wheat. Modern plant breeding based on achievements of genetics has a significant impact on plant resistance to diseases, climate variability and other factors. Genome wide association studies (GWAS) is one of genetics tools for mining of genome loci associated with economically important traits. In the current study, we applied GWAS to reveal QTL for spike productivity and grain quality using a panel of spring varieties of Triticum aestivum L. bred in different decades of the last century in Russia and Germany. The study has enabled to find new genetic markers associated with grain yield and quality. Studying genetic basis of grain yield and quality by comparison of wheat varieties from different breeding periods, including landraces preserved as the source of valuable genetic diversity for breeding and genetic studies, makes it possible not only to understand selection processes in the past, but also to develop strategies for future breeding work.

The required processes and steps for making bread include technological and innovative concepts. The current trend is the use of less toxic compounds and green processes. Besides lactic acid bacteria and yeast, other microorganisms with special properties, such as enzymes, new aroma and flavor, exopolysaccharides, and vitamins, among other compounds with beneficial properties, could be added to bread manufacture, improving bread quality and health effects for the consumers. Freeze drying, new encapsulation methods, cryoprotectants, spray drying, fluidized bed drying, and vacuum drying are used for probiotics and microorganism cultures that will be used as starters or biological additives in the fermentation. The same development is observed in the preservation methods, and studies with plant extracts and essential oils have been proposed and introduced, replacing chemical agents, such as propionate, within the clean-label bread formulations concept. Baking science is a growing research line incorporating innovative methods and biological additives.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

The increasing occurrence of widespread drought phenomena is a global environmental emergency, especially for the effects of ongoing climate change on groundwater availability. Dry years and extreme temperatures are common drivers of current climate impacts all over the world, including, for example, freshwater supply for drinking and agriculture purposes, ecosystems, forestry, health, etc.. In this frame, to ensure temporal water availability in water-stressed areas, a sustainable groundwater management is an increasing challenge. Most of groundwater in the South-East Latium Region, Central Italy, as in the whole Apennine Mountains chain, is stored in karst aquifers. In this area important water resources are present, but even here in the last decades they are affected by groundwater depletion as a consequence of occurring drought events, the upward trend in the globally average temperature and the increasing of anthropogenic activities. Due to the lack of flow rates data of springs in many areas of Italy, the spring response modeling could be a useful tool for supporting a proper water resource management. Several research studies proposed methods based on relationships between spring discharges and rainfall data. The goal of this paper is to propose a model, based on rainfall-discharges cross correlations, in order to assess the spring flow rate patterns of Capodacqua di Spigno Spring, which is the main one in the study area. The results obtained using the developed model has been compared to an existing method that uses the SPI index for the estimation of the minimum annual spring discharge.

Vacuum drying can dehydrate materials further than dry heat methods while protecting sensitive materials from thermal degradation. Many industries have shifted to vacuum drying as cost- or time-saving measures. Small-scale vacuum drying, however, has been limited by high costs of specialty scientific tools. To make vacuum drying more accessible, this study provides design and performance information for a small-scale open source vacuum oven, which can be fabricated from off-the-shelf and 3-D printed components. The oven is tested for drying speed and effective-ness on both waste plastic polyethylene terephthalate (PET) and a consortium of bacteria developed for bioprocessing of terephthalate wastes to assist in distributed recycling of PET for both additive manufacturing as well as potential food. Both materials can be damaged when exposed to high temperatures, making vacuum drying a desirable solution. The results showed the open source vacuum oven was effective at drying both plastic and biomaterials, drying at a higher rate than a hot-air dryer for small samples or for low volumes of water. The system can be constructed for less than 20% of commercial vacuum dryer costs for several laboratory-scale applications including dehydration of bio-organisms, drying plastic for distributed recycling and additive manufacturing, and chemical processing.

Natural phytochemicals in foods, including anthocyanins, can play an important role in human health. Anthocyanins have been reported to cause many various useful effects, such as reducing cancer cell proliferation, regulating blood pressure, preventing tumour formation, improving eyesight, and preventing diabetes. In this study, we aimed to reveal the qualitative anthocyanin content, antiproliferative and antimicrobial effects of different extracts derived from Vaccinium myrtillus, V. corymbosum, Sambucus nigra and Aronia melanocarpa. The anthocyanin content of the plants mentioned in the study was characterized after the freeze-drying process. MTT assay was used to determine the antiproliferative effect of extracts on cancer cells. Antimicrobial effects of extracts were studied on typical and clinical strains of 5 different bacteria. As a result, the anthocyanin content in the extracts obtained was determined to be quite good with the freeze-drying method, and it was also determined that the extracts had various levels of antiproliferative and antibacterial effects.

Dielectric elastomer actuators (DEAs) offer robust, high energy density solutions for soft robotics. The proposed end effector consists of three spring roll configuration DEAs, each acting as a robotic finger, using a 3M VHB-F9473PC adhesive membrane. The lateral force, bending angle and response time of the actuator are measured experimentally and compared with the predictions of an analytical model. The cylindrical actuator measures 70 mm in length and 15 mm in diameter and achieved a lateral force of 30 mN, a bending angle of 6.8 ° and a response time of ≈ 1 s. Spring roll configuration DEAs are shown to reduce the effects of viscoelasticity seen in the membrane, making the actuator more controllable at higher voltages. The dielectric constant of the membrane is shown to be a limiting factor of actuation, with a decrease in dielectric constant resulting in larger actuation. The end effector successfully gripped numerous light objects for extended periods, showing the applicability of spring roll DEAs for soft end effectors.

Earthquakes often entail alterations in the groundwater flow regime, in the phreatic level, in the surge and loss of springs, and discharge in brooks and springs. As for the latter, there are diverse feasible mechanisms, so there is a variety of theoretical approaches to elucidate the post-earthquake effects on spring discharge. This study adopts a conceptual approach, primarily presenting various methods for estimating water released by earthquakes by calculating discharge surpluses in springs. This study delves into refined techniques rooted in groundwater hydraulics, displaying applications of analytical and simulation methodologies to quantify seismic-induced groundwater discharge in springs. Investigating springs as natural indicators, this research applies mathematical precipitation-runoff models, specifically the CREC model, for simulating hydrographs in post-earthquake scenarios. We apply analytical procedures or mathematical simulation techniques employed in groundwater hydraulics for natural aquifer recharge calculations. Firstly, we briefly describe the methods based on the analysis of depletion curves of hydrographs in spring discharge. Additionally, certain mathematical rainfall-runoff models utilized in simulating hydrographs of karstic springs, along with derived analytical approximations, are adapted for this scenario. These hydraulic calculations involve the depletion coefficient and hydrodynamic volumes of aquifers, parameters that reveal certain aspects of the relation between groundwater and earthquakes, such as: a) Acknowledging faults as the primary geological structures in transmitting pore pressures due to earthquakes. b) Clarifying mechanisms of permeability enhancement during earthquakes. c) Highlighting the substantial volumes in motion within the Earth's interior, which, for instance, could constitute a significant source for the origin of mineral deposits. The findings highlight diverse features of the complex interplay between hydrogeological and tectonic processes at challenging spatial and temporal scales.

Many studies link changes in avian phenology in Europe to the North Atlantic Oscillation (NAO), as a proxy of conditions at western Europe. But effects of climate variation in other regions of Eu-rope on phenology of short-distance migrants with wide non-breeding grounds remain unclear. We determined the combined influence of large-scale climate indices, NAO, the Mediterranean Oscillation Index (MOI), and the Scandinavian Pattern (SCAND), during the preceding year on spring migration timing of European Wren at the southern Baltic coast during 1982–2021. We modelled the effects of these climate variables on the entire passage and subsequent percentiles of Wren’s passage at Bukowo-Kopań and Hel ringing stations. The start and median of migration shifted earlier at Hel, but the end of passage shifted later at both stations over 1982–2021. In the effect, the duration of passage at Hel extended by 7.6 days. Early passage at Hel was related with high MOI1 in spring and in preceding autumn. Spring passage at Bukowo-Kopań was late after high NAO in the previous breeding season, and high winter and spring NAO. At both stations late spring passage occurred after high SCAND in previous summer. Early beginning or median of passage at our stations followed high local temperatures. We conclude that phenology of Wren’s spring migration at the Baltic coast was shaped by conditions that different populations encounter at wintering quarters in western Europe, where NAO operates, and in the south-eastern Europe, where the MOI1 operates, in combination with conditions in Scandinavia during previous breed-ing season. We showed that climate variability in different parts of the migrants’ range has com-bined carry-over effects on in migrant’s phenology in Europe.

Cymbidium goeringii, locally known as the spring orchid in Korea, is one of the most important and popular horticultural species in the family Orchidaceae. C. goeringii cultivars were originated from plants with rare phenotypes in wild mountains where pine trees commonly grow. This study aimed to determine the cultivar-specific combined genotypes (CGs) of short sequence repeats (SSRs) by analyzing multiple samples per cultivar of C. goeringii. In this study, we collected more than 4,000 samples from 67 cultivars and determined the genotypes of 12 SSRs. Based on the most frequent combined genotypes (CG1s), the average observed allele number and combined matching probability were 11.8 per marker and 3.118×10-11, respectively. Frequencies of the CG1 in 50 cultivars (n ≥ 10) ranged from 40.9% to 100.0%, with an average of 70.1%. Assuming that individuals with the CG1 are genuine in the corresponding cultivars, approximately 30% of C. goeringii on the farms and markets may be not genuine. The dendrogram of the phylogenetic tree and principal coordinate analysis largely divided the cultivars into three groups according to their countries of origin; however, the genetic distances were not distant among the cultivars. In conclusion, this dataset of C. goeringii cultivar-specific SSR profiles could be used for ecogenetic studies and forensic authentication. This study suggests that genetic authentication should be introduced for the sale of expensive C. goeringii cultivars. We believe that this study will help establish a genetic method for the forensic authentication of C. goeringii cultivars.

Extraordinary high aerosol contamination observed in the atmosphere over Kyiv city, Ukraine, during the March – April 2020 period. The source of contamination was the large grass and forest fires in the northern part of Ukraine and the Kyiv region. The level of PM2.5 load investigated using newly established AirVisual sensors mini-network in five areas of the city. The aerosol data from the Kyiv AERONET sun-photometer site analyzed for that period. Aerosol optical depth, Angstrom exponent, and the aerosol particles properties (particles size distribution, single-scattering albedo, and complex refractive index) were analyzed using AERONET sun-photometer observations. The smoke particles observed at Kyiv site during the fires in general correspond to aerosol with optical properties of biomass burning particles. The variability of the optical properties and chemical composition indicates that the aerosol particles in the smoke plumes over Kyiv were produced by different burning material and phases of vegetation fires at different time. The case of enormous PM2.5 aerosol contamination in Kyiv city reveals the need to accept strong measures for forest fire control and prevention in Kyiv region, especially in the north-west region where radioactive contamination from Chornobyl disaster is still significant.

Globally, karst aquifers store large amount of precious water and create beautiful karst springs in many places. However, most of the karst springs flow declined, and some of the karst springs dried up with the effects of extensive groundwater development and climate variation. In order to obtain better understanding of factors contributing to the drying-up of karst springs, this study introduced grey system models to quantify spring flow taking Jinci Springs (China) as an example, which dried up in May 1994. Based on the characteristics of Jinci Springs flow, the spring flow was divided into two stages: the first stage (1954-1960), when the spring flow was affected only by climate variation; and the second stage (1961-1994), when the flow was impacted by both climate variation and anthropogenic activities. Results showed that the Jinci Springs flow had strong relations with precipitation occurring one year and three years earlier in the first stage. Subsequently, a grey system GM (1, 3) model with one-year and three-year lags was set up for the first stage. By using the GM (1, 3) model, we simulated the spring flow in the second stage under effects of climate variation only. Subtracting the observed spring flow from the simulated flow, we obtained the contribution of anthropogenic activities to Jinci Springs cessation. The contribution of anthropogenic activities and climate variation to Jinci Springs cessation was 1.46 m³/s and 0.62 m³/s, respectively. Finally, each human activity causing spring flow decline was estimated. The methods are useful to describe the karst hydrological processes under the effects of anthropogenic activities and climate variation.

This study has two main focuses: the first focus is to explore the design and the behavior of a locally built solar dryer during processing henna leaves. This was performed through the determination of the most important parameters that have effect on the drying process. Appropriately, it was found that the outlet air temperature of the solar collector depends entirely on the solar radiation, Moreover, the inlet temperature of the air to the drying chamber has also an important impact on the moisture content of the product. It was found that most of the studies dealing with solar drying do not take into consideration the quality of the final product. Accordingly, the second objective of this study is to present the effect of drying process on the quality of the drier samples. For this purpose, the bioactivity of the samples, in terms of determination of the total phenol content, total flavonoid content, and antioxidant activities was performed. Three different samples: fresh sample, samples dried with the presented solar dryer and open solar dried samples are tested. It was found that samples dried with the solar dryer presented the best results.

The objective of this study was to evaluate the drying kinetics of the mass of jambu leaves and mass of jambu leaves in foam mat at different temperatures (50, 60 and 70 °C and thickness of 1.0 cm). The physicochemical characterization of the materials was performed before and after drying. Twelve different drying models were fitted to the drying kinetics data and the thermodynamic properties were calculated. The physicochemical parameters for the mass of leaves and foam after drying were moisture content from 2 to 7%, ash from 13 to 17%, protein content from 22 to 30%, lipids from 0.6 to 4% and total titratable acidity from 0.20 to 0.28% of tartaric acid. Wang & Singh and Midilli models were recommended for describing the drying kinetics. The use of foam mat promoted higher values of effective diffusion coefficient and activation energy and lower values of enthalpy and entropy, thus enhancing the reduction of drying time.

The design of torsional springs for Series Elastic Actuators (SEAs) is challenging, especially when it comes to balancing good stiffness characteristics and efficient torque robustness. This study focuses on the design of a lightweight, low-cost, and compact torsional spring for use in rotary series elastic actuator (ES-RSEA) of lumbar support exoskeleton. The exoskeleton is used as an assistive device to prevent lower back injuries. The torsion spring was designed following design for manufacturability (DFM) principles, focusing on minimal space and weight. The design process consisted of determining the potential topology and optimizing the selected topology parameters through finite element method (FEM) to reduce equivalent stress. The prototype was made using a waterjet cutting process with low-cost material (AISI-4140-alloy) and tested using a custom-made test rig. The results showed that the torsion spring had a linear torque-displacement relationship with 99% linearity, and the deviation between FEM simulation and experimental measurements was less than 2%. The torsion spring has a maximum torque capacity of 45.7 Nm and a stiffness of 440 Nm/rad. The proposed torsion spring is a promising option for lumbar support exoskeletons and similar applications requiring high stiffness, low weight-to-torque ratio, and cost-effectiveness.

In December 2012, DOAJ’s parent company, IS4OA, announced they would introduce new criteria for inclusion in DOAJ [1] and that DOAJ would collect vastly more information from journals as part of the accreditation process – and that journals already included, would need to reapply in order to be kept in the registry. My hypothesis was that the journals removed from DOAJ on May 9th 2016 would chiefly be journals from small publishers (mostly single journal publishers) and that DOAJ journal metadata information would reveal that they were journals with a lower level of publishing competence than those that would remain in the DOAJ. Among indicators of publishing competence could be the use of APCs, permanent article identifiers, journal licenses, article level metadata deposited with DOAJ, archiving policy/solutions and/or having a policy in SHERPA/RoMEO. The analysis shows my concerns to be correct.

Two-phase olive pomace is a byproduct of the olive-oil extraction process that is sometimes processed further to recover more oil. During pomace oil production, especially in the early stages of olive processing, odours can be produced. These odours are a serious nuisance especially in and around the processing facilities, as well as for nearby communities. These odours can be strong and unpleasant, and they may result in various issues, including environmental concerns. Thus, in this paper, the effect of storage and drying on the composition of two-phase olive pomace was investigated. Several physicochemical and instrumental analyses were performed and it was concluded that the structural elements of pomace are not the ones who are affected during storage and drying. Storage and drying mainly impact the oil content of pomace, leading to an acidity increase and to the production of odorous oxidation compounds. Volatile acids, methyl and ethyl esters are released into the atmosphere causing serious environmental nuisance.

Grape dehydration is practiced widely in the food industry with large yields of sultanas produced globally. This paper proposes an investigation into grape microstructure changes as it is dried by imaging specimens at intervals during dehydration at two temperatures using scanning electron microscopy. Detailed images of the microstructure were obtained, and a unique image processing algorithm was developed to quantitatively analyse the properties of this microstructure. Two main methods were developed to obtain the complex boundaries of cells present in the grape tissue in over 36 SEM images. Segmentation of the binary image using an adapted watershed function obtained the most consistent and accurate morphological shape. This was compared to a secondary method which used Canny’s edge detection function, morphological closing and skeletonizing to outlines the cellular microstructure. MATLAB was utilised to convert these boundaries into measurable areas so that quantitative data on average cell area, perimeter and cell axis lengths was acquired. It was found that over drying time cell area and perimeter reduced as expected. Some variability in the data was clear due to only single samples being analysed for each temperature and time combination. The development of automatic image processing techniques will enable quantitative data to be extracted from these images. Trends in cell perimeter, diameter and shape will be used to demonstrate relationships between morphological structure, drying temperature, and duration.

Methylsilsesquioxane aerogels with uniform mesopores have been facilely prepared via a sol–gel process followed by microwave drying with methyltrimethoxysilane (MTMS) as precursor, hydrochloric acid (HCl) as catalyst, water and methanol as solvents, hexadecyltrimethylammonium chloride (CTAC) as surfactant and template and propylene oxide (PO) as gelation agent. The microstructure, chemical composition and pore structures of the resultant MSQ aerogels were investigated in detail to achieve controllable preparation of MSQ aerogels, and the thermal stability of MSQ aerogels was also analyzed. The gelation agent, catalyst, solvent and microwave power have important roles on pore structures of MSQ aerogels. Meanwhile, microwave drying method is found to not only have a remarkable effect on improving production efficiency, but also be conducive to avoid the collapse of pore structure especially micropores during drying. The resulting MSQ aerogel microwave-dried at 500 W possesses a specific surface area up to 821 m2/g and a mesopore size of 20 nm, and displays good thermal stability.

To accurately and non-destructively monitor the growth of spring wheat in the Hetao Irrigation Area, UAV remote sensing was employed during various fertility stages. Digital image indices from diverse fertilization treatments were calculated and compared with physiological indices to identify the most sensitive digital image indices corresponding to these indices. The study underscored the critical importance of the flowering stage in the growth of spring wheat, thus highlighting the necessity of focusing on this stage. This finding reiterated that the flowering stage was pivotal for spring wheat development in the Hetao Irrigation Area. Several digital image indices, such as GLA, R, G, INT, g, GRVI, MGRVI, RGBVI, EXG, and GRRI, exhibited a high frequency of significant correlations with physiological indices during the four primary reproductive stages of wheat. Consequently, these sensitive digital image indices during the flowering stage can more effectively characterize the physiological indices of spring wheat.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T₁ = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T₂ = 50 kg N ha^-1, T₃ = 100 kg N ha^-1 and T₄ = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T₅: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T₆: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T₇: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO₂ concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T₆ = Split N₁₀₀) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

In sustainable cultivation technologies, the method of managing crop residues and the microbiological activity of the soil supported by the application of effective microorganisms are of particular importance. Therefore, a four-year two-factor experiment was carried out with spring wheat monoculture. Six ways management of organic matter before sowing and tillage (first factor) and the application of microbiological preparations (second factor) were tested - a total - 18 experimental objects. Parameterized: weed infestation, SPAD and LAI indicators, elements of the yield structure and spring wheat yield - all features were significantly determined by the tillage technology used. In most cases, the application of biopreparations does not have a significant impact on the tested features. It was found that the highest yields of spring wheat obtained in the technology: application of EM or UGmax microbiological preparations on the shredded straw of the forecrop and mixing it with the soil using a grubber immediately after harvest, sowing of the white mustard catch crop and winter plowing.

In recent years, the potential of insects has been explored as a sustainable protein alternative to sustain the growing world population. Differences in the way insects are processed can affect their proximate composition and digestibility. This work studies the effects of the combination of different types of slaughter methods and drying temperatures on the proximate composition, organic matter digestibility (OMd), hydrolysis degree (DH/NH2 and DH/100 g DM), total hydrolysis (TH) and hygienic sanitary study of BSFL (black soldier fly larvae). Four types of slaughter methods were used: frozen (F), blanched + frozen (B), Melacide® + frozen (M) and liquid nitrogen (N), each with three drying temperatures (50, 70 and 90 °C). A negative correlation between acid detergent fibre (ADF) and protein digestibility parameters was obtained. 70 °C was the most suitable drying temperature, as it reported higher values of protein digestibility (DH, TH), resulting in hygienic and sanitary conditions suitable for food use. Slaughtering with liquid nitrogen and blanching were more convenient than traditional freezing or the use of Melacide® to achieve higher protein digestibility results.

Microencapsulation by atomization can be used to minimize the loss of bioactive compounds, improving the characteristics and applicability of the powdered product. This study evaluates the effect of different encapsulating agents (maltodextrin, gum arabic, and chitosan) and three spray nozzle diameters (1.0, 1.2, and 1.5 mm) on the atomization of guavira (Campomanesia adamantium) pulp with added 6% bocaiuva (Acrocomia aculeata) dehydrated pulp in the green maturation stage. The experiment followed a simplex-centroid mixed design, with carrier agent concentrations and spray nozzle diameters as independent variables and powder yield, solubility, hygroscopicity, and vitamin C content as dependent variables. The results show that gum arabica increased powder yield and vitamin C retention. The addition of maltodextrin resulted in powders with increased solubility and low hygroscopicity. Furthermore, the optimization tool indicated that the best process conditions were achieved with the addition of gum arabic (10.8%) and chitosan (7.2%), resulting in powders with 29.48% yield, 82.96% solubility, 15.90% hygroscopicity and 741.11 mg/100g vitamin C. Furthermore, the 1.0 mm diameter spray nozzle was considered the most suitable for obtaining guavira pulp microparticles with higher ascorbic acid content.

Keywords: keyword 1; keyword 2; keyword 3 (List three to ten pertinent keywords specific to the article yet reasonably common within the subject discipline.)

This study investigates the use of programming language Python to analyse and model chemical engineering processes. Using municipal sewage sludge (MSS) drying as an example, the study demonstrates how Python can support analyses and model drying data. The drying process was performed on a flat plate while maintaining a uniform, parallel drying air speed of 1.15 m s-1. The Python program helped to analyse the digitalised weight measurements from each sample. The program enables sorting input data, determining the drying critical point and evaluating the first and second drying periods.

The spring-in phenomenon of the composite parts can affect the assembly process. This study aims to predict the spring-in phenomenon of carbon fiber reinforced plastic (CFRP) part. Here, we predict the spring-in of the CFRP part using a coupled analysis of the forming and cooling processes during the stamping process. First, a simulation of the entire forming process, such as the transfer of the composite laminate, gravity analysis, and forming was performed to obtain the temperature distribution of the CFRP part. Subsequently, a finite-element (FE) simulation of the cooling process was conducted to predict the spring-in phenomenon of the shaped CFRP part using the temperature data obtained in the forming simulation. Finally, a CFRP part was manufactured and compared with the results of the FE simulation.

Water and nutrients shortage threatens agricultural sustainability in many arid and semiarid areas of the world. It is unknown whether improved water and nutrient conservation practices can be developed to alleviate this issue while increasing crop productivity. In this study, experimental work included the application of straw, biochar and N fertilizer. The straw and biochar were applied alone or combined with N fertilizer (0 and 100 kg N ha-1). Application of biochar and straw in combination with N fertilizer caused a reduction in mean soil temperature by an average of 20.05% and 18.10% relative to soils without carbon. Biochar and straw– amended soils significantly (P < 0.05) increased soil moisture content by 11.04% and 13.68% compared to no carbon treatments. Statistically comparable temperatures and moisture were recorded for both straw and biochar treated plots. Both biochar and straw treated soils produced the lowest bulk density (0–5 cm) at 1.15 g cm–3, and no carbon soils the highest at 1.20 g cm–3. The improved soil quality translated into higher biomass in the biochar (1906 kg ha–1) and biomass (1643 kg ha–1) and soils without carbon the lowest at 1553 kg ha–1. The improvement of soil moisture and the optimization of soil temperature for the two residue treated soils allow us to conclude that combined application of biochar and straw at the rate used in this study can be used as an effective farming model in alleviating water and nutrient shortage in semiarid environments.

The microwave field is used for drying and disinfection of grain, during pre-sowing seed treat-ment. The use of a microwave field in these installations leads to an increase in their productivity and a decrease in the energy consumed by them. One of the principal problems of microwave field use for treatment of dense grain layers is to insure sufficient distribution uniformity of the field. In this article, waveguide design options have been discussed that serve to introduce microwave radiation into the grain layer. Mathematical simulation of the electromagnetic field distribution was performed with the use of CST Microwave Studio software in order to evaluate and compare horn-type, rectangular and semicircular waveguides. The data on the standing wave ratio and radiation efficiency for these types of waveguides have been reported. Specific features of the microwave electromagnetic field distribution and radiation power in the output of those wave-guides have been described. Results of mathematical simulations enabled to make out that sem-icircular waveguides with slot-type radiators are preferable for processing dense grain layers.

The potential of sodium alginate (ALG) and gum arabic (GA) as wall polymers for L-ascorbic acid (AA) encapsulation as a tool for their preservation against the thermo-oxidative degradation was investigated. The influence of such polymers used as wall material on the AA-content, size, encapsulation efficiency, encapsulation yield and thermo-oxidative stability were evaluated. The AA-microparticles were obtained using the spray-drying technique. An experimental Taguchi design was employed to assess the influence of the variables in the encapsulation process. The microparticles morphology and size distribution were characterized by scanning electron microscopy and laser diffraction. The thermal stability of AA microparticles was studied by differential scanning calorimetry and thermogravimetry analysis. This work points out the viability to encapsulate AA using GA and ALG through a spray-drying process. In general, a product yield ranging from 35.1% to 83.2% and an encapsulation efficiency above 90% was reached. Spherical microparticles with a smooth surface were obtained with a mean diameter around 6 μm and 9 μm for the those prepared with GA and ALG, respectively. The thermo-oxidative analysis showed that both polymers allow maintaining AA stable up to 188 °C, which is higher than the traditional processing temperature used in the fish feed industry.

Umbu is a tropical fruit with high content of bioactive compounds. However, maturation causes significant losses on nutrient density reducing the nutritional value of this highly appreciated fruit. Thus, the objective of the present work was to encapsulate the Umbu fruit bioactive compounds using spray drying and identify the variables affecting the biomolecules preservation. A Box-Behnken experimental design with 3 factors was set varying inlet temperature, atomization flow rate, and maltodextrin concentration for process otimization. Then the powder physicochemical and chemical properties were characterized, and results were modeled using a polynomial equation. Results revealed that the droplet size and maltodextrin concentration had a significant influence on the conservation of the biomolecules. Drying kinetics favoring fast formation of a particle crust increases encapsulation efficiency. Bioactive compounds retention was achieved by increasing maltodextrin even at high temperatures, where a matrix is formed hindering chemical degradation. Process optimization was validated and revealed low inlet temperatures (122ºC), high atomization flow rate (5kg/h) and high maltodextrin concentration (20%) to be the most desirable conditions for bioactive compounds retention.

Soil tillage intensity influences the distribution of nutrients, and soil’s physical and me-chanical properties, as well as gas flows. The impact of reduced tillage on these indices in spring barley cultivation is still insufficient and requires more analysis on a global scale. This study was carried out at Vytautas Magnus University, Agriculture Academy (Lithu-ania) in 2022–2023. The aim of the investigation was to determine the effect of the tillage systems on the soil temperature, moisture content, CO2 respiration and concentration in spring barley cultivation limited by the semi-humid subarctic climate. Based on a long-term tillage experiment, five tillage systems were tested: deep and shallow mold-board ploughing, deep cultivation-chiselling, shallow cultivation-chiselling, and no-tillage. Shallow ploughing technology was found to be better at conserving soil moisture and maintaining a higher temperature. Deep cultivation had a lower moisture content and lower soil temperature. Shallow cultivation fields in most cases increased CO2 emissions and CO2 concentration. The results show that in direct sowing fields, most cases had a positive effect on crop density. Direct sowing fields resulted in significantly lower grain yields of spring barley in the years studied.

On 5-7 April 2018 a landfalling atmospheric river resulted in widespread heavy precipitation in the Sierra Nevada of California and Nevada. Observed snow levels during this event were among the highest snow levels recorded since observations began in 2002 and exceeded 2.75 km for 31 hours in the northern Sierra Nevada and 3.75 km for 12 hours in the southern Sierra Nevada. The anomalously high snow levels and over 80 mm of precipitation caused flooding, debris flows, and wet snow avalanches in the upper elevations of the Sierra Nevada. The origin of this atmospheric river was super typhoon Jelawat, whose moisture remnants were entrained and maintained by an extratropical cyclone in the northeast Pacific. This event was notable due to its April occurrence, as six other typhoon remnants that caused heavy precipitation with high snow levels (mean = 2.92 km) in the northern Sierra Nevada all occurred during October.

Olive tree vegetal materials are considered a powerful source for isolation of bioactive compounds, mainly, phenols and triterpenic acids. However, the high humidity content of them reduces their preservation and extractability to a liquid solvent. Accordingly, a drying step is crucial to homogenize the material and to obtain an efficiency extraction. We studied the influence of the drying process on the extraction efficiency of bioactive compounds from olive vegetal material. For this purpose, we evaluated the effects of four drying processes on the solid–liquid extraction of bioactive compounds from two by-products, olive leaves and pomace, and olive fruits harvested from two cultivars, Alfafara and Koroneiki. Infrared-assisted drying (IAD) was the most suited approach to obtain extracts enriched in oleuropein from leaves. In the case of pomace, lyophilization and microwaves-assisted drying led to extracts concentrated in oleacein and oleuropein aglycone, whereas IAD and oven-drying led to extracts with enhanced content in hydroxytyrosol glucoside and hydroxytyrosol, respectively. The drying process affected considerably to the chemical composition of extracts obtained from fruits. Changes in the composition of extracts were explained essentially by the drying process conditions using auxiliary energies, temperature and time, which promoted chemical alterations and increased the extractability of compounds.

Aqueous and ethanolic extracts of Hibiscus sabdariffa were spray-drying using maltodextrin (MD) and gum arabic (GA) as carriers agents. An experimental design Taguchi L8 with seven variables was implemented. Physicochemical properties in the encapsulates were evaluated by UV-Vis, XRD, spectroscopy and gravimetric techniques. Treatments with aqueous extracts showed the highest concentration of total soluble polyphenols (TSP) 32.12- 21.23 mg EAG/g DW, and antioxidant capacity (AOX) for ABTS assay. The best treatment for TSP and AOX was T4: 2.5% Hibiscus w/w, aqueous extracts, decoction, extract-to-carrier ratio 1:1 (w/w), proportion to carriers (MD:GA) 80:20 (w/w), 10000 rpm, 150°C. Taguchi L8 model is a tool that allows the use of multiple variables with a low number of treatments that indicate the drying conditions that give the best parameters, focusing mainly on TSP and AOX, in addition, is a good alternative for the preservation and stability of the PC in Hibiscus.

The study investigates the evolution of soil pore structure and shear strength deterioration in compacted clayey soil under controlled wetting and drying (wd) cycles, which are expected to become more frequent due to climate change. Thirty soil samples were compacted at optimal moisture content and 90% of maximum dry density. These samples were then subjected to 0, 1, 5, 10, and 15 controlled wd cycles from saturation to the wilting point, and volumetric changes were recorded during each cycle. After the wd treatment, the soil samples were scanned using X-ray Computed Tomography (CT) at 50 μm resolution and then sheared under unconsolidated-undrained and consolidated-undrained conditions in a triaxial test. Significant shrinkage and swelling of soil samples were observed during wd cycles, with average volumetric strain fluctuating between +12% at saturation and -5% at the wilting point. X-ray CT visualisation and analysis revealed higher porosity, more prominent pores and increased pore length in soil samples with increasing wd cycles. Both undrained and effective soil shear strength markedly decreased with increasing wd cycles. CT-derived macroporosity and pore length were significant predictors of the soil's undrained and effective shear strength when exposed to wd cycles. The findings emphasise the considerable impact of climate change, specifically wd cycles, on clayey soil, highlighting the need for consideration in the design of earth-based infrastructure.

In recent years, the interest in increasingly sustainable agriculture has also turned attention towards new crops which could enter the food chain as new protein and oil sources or that can be used as new cover crops. In this scenario, Camelina sativa is a perfect crop to study. Camelina is an annual herbaceous plant belonging to the Brassicaceae which is interesting for its oil content, since the seeds contain about 40% of oils, with a high level of polyunsaturated fatty acids (30-40% alpha linolenic acid, 15-25 % linoleic acid, 15% oleic acid and about 15% eicosenoic acid). It is a hexaploid species (2n = 40, genome size ~782 Mb) characterized by rapid growth, short life cycle (85-100 days for spring varieties, 190-210 for autumn varieties) and low input cultivation needs. All these traits make it suitable for use in marginal areas. However, its use in feed and food is limited by the presence of glucosinolates (GLS). GLS are sulfur molecules involved in plant defense. In recent years, they have been studied not only as anti-nutritionals, but also for their anti-carcinogenic effects against chronic inflammatory and heart diseases and for their use as natural pesticides. Given the recent interest in camelina and its highly nutritious oil, eight pure lines and a synthetic population were compared in two different growing periods, spring and winter. In this work, the genetic materials were characterized for different phenotypic traits, yields and yield components, bromatological and glucosinolate content. The results confirmed that in North Italy camelina has higher yields if cultivated in the autumn-winter period (about 2 t/ha vs 0.6 t/ha), furthermore, a negative correlation was found between spring and winter yields, indicating that varieties that produce more in winter cultivation produce less in spring cultivation. Moreover, to our knowledge, it is the first work in which a synthetic population of Camelina sativa has been tested and proved to be a valid solution for use in various environments both for its adaptability and for the low content of glucosinolates (about 17 mmol/ kg).

Metal, primarily Fe and Zn, deficiencies affect over half of the world's population. Human diets with prevalent cereal products cause micronutrient malnutrition. Biofortification is one of the most effective approaches to alleviate malnutrition. Spring wheat genetically stable (M7) mutant lines developed with 100 and 200 Gy gamma treatments to broaden genetic variation and search for new resources were analyzed for nutritionally important minerals (Ca, Mg, K, Fe, and Zn), their bioavailability, and grain protein content (GPC). The variation was 172.3–883.0 mg/kg for Ca, 472.9–1088 mg/kg for Mg, 3128.6–5487.5 mg/kg for K, 40.9–89.0 mg/kg for Fe, and 22.2–89.6 mg/kg for Zn. In mutant lines, among the investigated minerals, the highest increases in concentrations were observed in Fe, Zn, and Ca when compared to the parent. Some mutant lines, mostly in the 100 Gy-derived germplasm, had two to three times higher Fe, Zn, and Ca concentrations, lower phytic acid concentration (1.4–2.1 times), and 6.5–7% higher GPC compare to the parent. Variation was detected for the Ca:Phy, Mg :Phy, Phy:K, Phy:Fe, and Phy:Zn molar ratios, (1.27–10.41, 5.05–18.68, 1.66–4.87, 1.40–5.32 and 1.78–11.78, respectively). The results showed how the genetic variation could be generated through radiation and be useful to develop biofortification by micronutrient varieties with their appropriate bioavailability to overcome malnutrition.

Locally advanced rectal cancer (LARC) has traditionally been treated with trimodality therapy consisting of neoadjuvant radiation +/- chemotherapy, surgery and adjuvant chemotherapy. There is currently a clinical need for biomarkers to predict treatment response and outcomes, especially during neoadjuvant therapy. Liquid biopsy in the form of circulating tumour cells (CTCs) and circulating nucleic acids in particular microRNAs (miRNA) are novel, highly stable and clinically relevant regulators of disease. We studied a prospective cohort of 52 patients with LARC, and obtained samples at baseline, during treatment, and post-treatment. We enumerated CTCs during chemoradiation at these three time-points, using the IsofluxTM CTC Isolation and detection platform. We then subjected the isolated CTCs to miRNA expression analyses, using a panel of 106 miRNA candidates. We identified CTCs in 73% of patients at baseline, and numbers fell during treatment and miRNA expression profiles also changed during treatment. Between baseline and during treatment (week 3) time-points three microRNAs (hsa-miR-95, hsa-miR-10a and hsa-miR-16-1*) were highly differentially expressed. Importantly, hsa-miR-19b-3p and hsa-miR-483-5p were found to correlate with good response to treatment. The latter (hsa-miR-483-5p) was also found to be differentially expressed between good responders and poor responders. They represent potential predictive biomarkers and a potential miRNA-based treatment strategy. In this study, we demonstrate that CTCs are present and can be isolated in the non-metastatic early stage cancer setting, and their associated miRNA profiles can potentially be utilized to predict treatment response.

This study presents an experimental investigation of the convective drying process of ginger rhizomes (Zingiber officinale). It analyses the effect of moisture content on the thermal properties of dried ginger rhizomes. Drying experiments were conducted under controlled conditions to establish the relationship between moisture content and thermal conductivity. The drying kinetics were examined to provide insights into the drying behaviour of ginger rhizomes and the influence of moisture content on their thermal properties. The results demonstrated a significant impact of initial moisture content and convective drying conditions on the drying process. As drying progressed, the moisture content decreased, leading to a reduction in thermal conductivity. It was observed that drying under convective drying takes 24 hours compared to open sun drying at nine days and solar tunnel drying at eight days. The drying temperature of 60°C was considered optimum. The results show that dried ginger at an absolute moisture content of 6.63% (wb) with a thermal conductivity of 0.0553W/m. K for unblanched ginger, 9.04% (wb) with thermal conductivity of 0.0516W/m. K for blanched ginger, 8.56% (wb) moisture content with a thermal conductivity of 0.0483W/m. K for peeled ginger and 5.98% moisture content with a thermal conductivity of 0.0460W/m. K for unpeeled ginger would be ideal for making powdered ginger rhizomes. These findings have practical implications for the food industry, as they can aid in designing and improving drying processes for ginger rhizomes and similar agricultural products. By understanding the relationship between moisture content and thermal properties, more efficient drying strategies can be developed to minimise energy consumption and maintain the quality of the dried product.

Drought events are predicted to become more prevalent in the future. Evaluating the performance of herbicide-resistant and susceptible weed ecotypes to progressive drought can provide insights into whether resistance trait(s) increased or reduced the fitness of a resistant population. Two experiments were conducted in the greenhouse between January and May 2021 to evaluate drought tolerance differences between Palmer amaranth accessions resistant to S-metolachlor or glyphosate and their susceptible counterparts. The accessions used were: S-metolachlor-resistant (17TUN-A), a susceptible standard (09CRW-A), and glyphosate-resistant (22 to 165 EPSPS copies) and glyphosate-susceptible (3 to 10 EPSPS copies) plants from accession 16CRW-D. Daily transpiration of each plant was measured. The daily transpiration rate was converted to normalized transpiration ratio (NTR) using a double-normalization procedure. The daily soil water content was expressed as a fraction of transpirable soil water (FTSW). The threshold FTSW (FTSWcr), after which NTR decreases linearly, was estimated using a two-segment linear regression analysis. The data showed differences between S-metolachlor- resistant and -susceptible accessions (P ≤ 0.05). The FTSW remaining in the soil at the breakpoint for the S-metolachlor-susceptible accession (09CRW-A) was 0.17±0.007. The FTSW remaining in the soil at the breakpoint for the S-metolachlor-resistant accession (17TUN-A) was 0.23±0.004. Although the mechanism endowing resistance to S-metolachlor might have contributed to increased drought tolerance, follow-up experiments are needed to verify this finding. Increased EPSPS copy number did not improve drought tolerance of Palmer amaranth.

Onion (Allium cepa L.) is a strong-flavoring vegetable consumed in different ways. It is mainly due its distinctive flavor or simply pungency. Onion has also important natural compounds effective for medical functions such as inhibition of bone resorption, lower risk of cardiovascular disease and cancer. This importance is directly related to high content of organo-sulphur compounds. Shelf life of fresh onion bulb is short enough about two weeks at ambient storage conditions in Fogera district, Amhara region, Ethiopia. This is mainly due to the presence of high moisture in fresh onion bulbs. Postharvest loss of onion bulb reaches up to 50% in the production season in Fogera district. Consequently onion bulb had extreme variable market price during production and off season in the district which directly influences both the growers and consumers. In this study the effect of different drying techniques on nutritional and volatile components of onion were evaluated. Effect of different drying techniques on protein, carbohydrate, total sugar, fat, pyurvic acid, ascorbic acid, total phenol, total flovonol, rehydration ratio, color and sensory properties of onion slice were evaluated and found insignificant at (P > 0.05) for microwave and modified direct solar dryers taking fresh onion bulb as a control. But oven drying method had significant effect on onion physicochemical quality attributes at (P < 0.05) as compared to fresh onion bulbs.

Evaluating genetic diversity in walnut (Juglans regia L.) populations is a rapid approach used by walnut breeding programs to distinguish superior genotypes. The present study identified the Hamedan province walnut population as one of the richest, most genetically diverse regions in Iran during 2019-2020. After initial screening, 47 genotypes were selected for further evaluation of pomological and phenological traits based on International Plant Genetic Resources Institute (IPGRI) descriptors. Nut and kernel weights among the selected genotypes ranged between 7.15-21.05 g and 3.0-10.8 g, respectively. Principal component analysis (PCA) categorized genotypes into three distinct groups while cluster analysis (CA) further categorized genotypes into one of four groups. Spearman correlation analysis showed a positive correlation (P <0.01) between nut weight (NWT), nut size, and kernel weight (KW) while a negative correlation (P <0.01) between shell thickness (STH) and packing tissue thickness (PTT) with kernel percentage (KP) was observed. Lastly, 10 of 47 genotypes (TAL8, TAL9, TAL10, TAL14, TAL19, TAL22, TB2, TB4, TB6, and RDGH5) were considered superior. Superior genotypes were late-leafing (25-40 days after the standard) and displayed a lateral bearing (LB) habit with heavy nuts (12.52–16.82 g) and kernels (6.53–8.15 g), thin-shells (1.06–1.25 mm), and lightly-colored kernels. Cuttings of superior genotypes were then grafted in the orchard. Detecting superior and late-leafing genotypes in this investigation suggests cultivars resistant to late-spring frost may soon be isolated.

Gelidium jelly was traditionally made by boiling processed Gelidium seaweed and allowing the filtrate to congeal into jelly. The processing of Gelidium seaweed was very complicate involved the repeated procedures of water washing and sun drying for 7 times, and the seaweed was originally purple-red in color turned into yellow after the repeated wash and sun drying. This study aimed to evaluate the effects of halogen lamp drying methods in replace of sun drying on the physical-chemical qualities of Gelidium jellies. Properties included the agar yield, gelling temperature, hardness, springiness, rheological parameters, sensory attributes, color, and volatile compounds were investigated. The results demonstrated halogen lamp drying method required 12 times of washing and drying processes to achieve the similar jelly properties compared to sun drying for 7 times in the experimental conditions. Volatiles including heptanal, β-ionone, and (E)-2-decenal could be used as indicators to monitor the washing and drying processing. Halogen lamp was found could be an alternative processing method for seaweed drying, especially at rainy days.

The focus of this study was to evaluate the effectiveness of incorporation of phenolic compounds from blueberry juice into pear slices using a combination of ohmic heating (OH) and vacuum impregnation (VI), followed by air- or freeze-drying. The results showed that OH is a valuable technique to increase the content of bioactive compounds and antioxidant capacity of blueberry juice. The optimal OH treatment is heating the juice at 50 °C for 20 min under an electric field of 13 V/cm. Furthermore, the combination of VI and OH showed the efficiency of enriching pear slices with bioactive compounds from blueberry juice. The best treatment is to immerse the slices for 90 min at 50 °C and an electric field of 7.8 V/cm. The presence of anthocyanin pigments from blueberry juice affects the color parameters of pear slices by increasing the a* parameter and decreasing the b* and L* parameters. However, both freeze-drying and air-drying (at temperatures of 40, 50, and 60 °C) negatively affected the phenolic content and antioxidant capacity. Notably, air-drying at 60 °C highest levels of phenolic compounds and antioxidant potential for both impregnated and non-impregnated pear slices among the drying processes applied.

This research work is concerned in the exergy analysis of the continuous-convection drying of onion. The influence of temperature and air flow rate was studied in terms of exergy parameters. The energy and exergy balances were carried out taking into account the onion drying chamber. Its behaviour was analysed based on exergy efficiency, exergy loss rate, exergetic improvement potential rate and sustainability index. The exergy loss rates increase with the temperature and air flow rate augmentation. Exergy loss rate is augmented at higher drying air temperatures and flow rates because the overall heat transfer coefficient increase. On the other hand, the exergy efficiency increases with the air flow rate augmentation. This behavior is due to the energy utilization was improved because the most amount of supplied energy was utilized for the moisture evaporation. However, the exergy efficiency decreases with the temperature augmentation due to the free moisture is less, then, the moisture begins diffusing from the internal structure to the surface. The exergetic improvement potential rate values show that the onion drying process presents a high potential to improve the exergy efficiency. The sustainability index of the drying chamber varied from 1.9 to 5.1. To reduce the environmental impact of the process, the parameters must be modified in order to ameliorate the exergy efficiency of the process.

Accurate and robust methods are needed to monitor crop growth and predict grain yield and quality in breeding programs under variable agrometeorological conditions. Field experiments were conducted during two successive cropping seasons (2021, 2022) at four trial locations (Estonia, Latvia, Lithuania, Norway). The focus was on assessment of grain yield (GY), grain protein content (GPC), and UAV-derived NDVI measured at different plant growth stages. Performance and stability of 16 selected spring wheat genotypes were assessed under two N application rates (75, 150 kg N ha−1) and over contrasted agrometeorological conditions were assessed, and the quantitative relationships between agronomic traits and UAV-derived variables were figured out. None of the traits were subject to a significant (p&lt;0.05) genotype by nitrogen interaction. High-yielding and high-protein genotypes were detected with high WAASB stability, specifically under high and low N rates. This study highlights the significant effect of NDVI analysis on growth stages GS55 and GS75 as key linear predictors, especially in the context of spring wheat GY. However, the effect of these indices depends on the specific growing conditions in the respective locations, thus limiting their universal utility.

Sanctuaries devoted to Asclepius were established and operated for almost a thousand years in various Greek and Roman cities throughout the Mediterranean region. The Asclepieion sanctuary in Lenta (formerly known as Ancient Lebena) in Crete was famous for receiving water from a sacred spring. In the Ancient Lebena, Levinaion was a famous centre for hydrotherapy, physiotherapy and a psychiatric hospital. In the present paper, we aim to assess the hydrochemical status of this sacred spring that holds a prominent position in archaeological and historical studies. The main objectives of this study are: Initially, to present supervisory evidence (archaeological, geological, hydrochemical) of an area that was a water resource management model for many centuries, carrying out therapeutic work. The second objective is to present and compare hydrochemical data in the last century, i.e. from 1915 to 2021. The third objective is to highlight and warn of an incipient saltwater intrusion in the area along the Lentas coast. The fourth objective is to propose an alternative and sustainable form of water resources management in the region that requires the study and rational utilization of the sporadic small water springs in the region. Our study focuses on a basic hydrochemical analysis of spring and borehole water in the remains of Levinaion in the Lentas region and their comparison with spare historical data of the sacred spring water, aiming to interpret the impact of the changes in the spring water resources that occurred in the last decades due to urban modernization. Our results highlight (i) visible fluctuations in chemical composition of borehole water samples, (ii) a neutral to alkaline pH in borehole waters, and an alkaline pH in spring waters, (iii) un-detectable arsenic of Lentas borehole water, unlike historical data of Lentas spring water, (iv) low values of dissolved radon of Lentas borehole water and spring water of Kefalovrysa, and (v) a timeless constant and hypothermic nature of the water of both sacred spring and borehole of Lenta, but also of Kefalovrysa spring. The recorded historical data, i.e. from 1915 to 1957, due to the absence of substantial anthropogenic activity in the area, can be used as reference values (natural background levels, NBLs) for the Lentas area. Our findings emerge with the need to bring again the flowing spring water of the sacred spring of Lentas in its original form through sustainable management and re-discover its beneficial therapeutical effects.

Is it possible that the addition of wild-growing flowers with anti-inflammatory applications can improve the antioxidant properties of rapeseed and multifloral honey? The study objective was a comparative analysis of two honey varieties enriched by flowers of six plant species, based on the content of the antioxidant capacity as well as total flavonoids and phenolic content. Experiments demonstrated that at each level of enrichment there was an improvement in antioxidant properties compared to honey of both varieties without additives, especially in the case of dried flowers. Primula veris L. and Pulmonaria officinalis L. improved the antioxidant properties and phenolic content most effectively in honey at all levels of enrichment. Rapeseed-type honey produces a better matrix for the incorporation of natural plant metabolites into honey. The content of biologically active substances in honey enriched with flowers gives hope for new applications of health-promoting substances contained in wild plants.

This study aimed to investigate the impact of incorporating Refuse Derived Fuel (RDF) into a production brick mixture in order to mitigate difficulties encountered in the production environment. Three distinct tests were conducted to assess the preparation process. The first test served as a reference, utilizing 100% clay material without RDF. The second test involved the inclusion of 10% RDF, obtained from a waste factory, with a grain size less than 20mm. In the third test, the RDF was mixed with silica sand after undergoing hammer milling with a 2mm sieve, followed by a 10% incorporation into the mixture. The primary objective was to comprehend the behavior of these mixtures in two critical stages: extrusion and drying. Extrusion performance was evaluated by examining the shaping process from the mold, vacuum conditions within the extruder, and the cutting of wet sample bricks. Furthermore, the drying procedure was assessed in terms of shrinkage, drying sensitivity, and appearance. Comparisons were made among the three test scenarios to identify the influence of RDF on these key parameters. Preliminary results indicate that the inclusion of RDF impacted the extrusion process. The addition of RDF resulted in variations in the flow characteristics of the mixture, affecting the shape formation from the mold and the vacuum conditions within the extruder. Additionally, the cutting of wet sample bricks exhibited some differences compared to the reference test. Concerning the drying phase, the presence of RDF influenced shrinkage behavior and drying sensitivity. The mixture with RDF showed different shrinkage patterns compared to the reference, and its drying sensitivity was altered. Moreover, the appearance of the bricks after drying exhibited notable variations due to the incorporation of RDF. In conclusion, incorporating RDF in the brick mixture introduces changes in both the extrusion and drying stages. The alteration in flow characteristics and vacuum conditions during extrusion, as well as the variations in shrinkage, drying sensitivity, and appearance during drying, suggest that further investigation is necessary to optimize the incorporation of RDF for improved brick production. These findings contribute to the understanding of the challenges and opportunities associated with the utilization of RDF in brick manufacturing processes.

The flower of Syringa pubescens Turcz. is a Chinese folk medicine and also used as flower tea for healthcare. The effects of five drying methods on the active compound contents, the antioxidant abilities, anti-inflammatory properties and enzyme inhibitory activities were evaluated. The plant materials were treated using shade-drying, microwave drying, sun-drying, infrared drying and oven drying. The seven active compounds were simultaneously determined by an HPLC method. Furthermore, the chemicals differences were assessed using Scanning electron microscopy, UV spectroscopy and infrared spectroscopy. The antioxidant capacities and protective effects on L02 cells induced by hydrogen peroxide were measured. The anti-inflammatory effects on lipopolysaccharide-induced RAW264.7 cells were investigated. The enzyme inhibitory activities were determined against α-amylase, α-glucosidase cholinesterases and tyrosinase. The results indicated that drying methods had significantly influences on the active compound contents and biological properties. In consideration of the contents of bioactive compound, the suitable drying methods were SHD, SD, OD and MD. The SHD sample exhibited stronger radical scavenging ability on DPPH, ABTS, hydroxyl and superoxide anions and higher reducing power compared with other samples prepared by SD, OD, MD and IRD. Moreover, SHD sample had strong protective effects against L02 cells damage induced by H2O2. SPF samples, especially SHD sample, significantly inhibited inflammatory factor secretion in LPS-stimulated RAW 264.7 cell. All studied SPF sample exhibited evidently inhibitory effects on the four enzymes. SHD sample possessed the highest inhibitory activity on α-glucosidase and α-amylase. While SHD and SD samples had the potential inhibitory effects on cholinesterases and tyrosinase. In consideration of active compound contents and biological activities, it was recommended that SHD and SD were applied for drying SPF at an industrial scale.

Immobilized metal ion affinity adsorbents have been widely used in separation technique to purify proteins. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion has been applied to clinical trial. In this study, in order to prevent the leakage of Zn²⁺ loaded from cellulose beads based adsorbent, improve its stability and adsorption capacity for testosterone, Freeze-drying method was used to enhance the porosity of cellulose beads, improve the surface area of the cellulose beads and adsorption capacity for testosterone. Chitosan was used to coat the adsorbents for preventing the leakage of Zn²⁺ loaded and improve the adsorbent’s stability. Moreover, the factors affecting adsorption ability and some components in plasma were also investigated. The results indicate the adsorption ability of the adsorbent can be significantly improved by freeze-drying. After the adsorbent was coated with 0.02% chitosan solution, the highest adsorption percentage reached 48%. During adsorption, the Zn²⁺ concentration in plasma did not rise. In addition, the adsorption percentage for total proteins was below 15%. The results may be caused by the pore size and surface area of the adsorbent enlarged via freeze-drying, and the chitosan solution went into the pores and coated the outer and inner surface of the adsorbent. The adsorbent has a potential clinical application to remove testosterone in patients with recurrent and metastatic prostate cancer.

The role of the databases is to allow persisting data, no matter if they are of the SQL or NoSQL type. In SQL databases, data is structured in a set of tables in the relational database model, grouped in rows and columns. The CRUD operations (create, read, update, and delete) are used to manage the information contained in the relational databases. Several dialects of the SQL language exist, as well as frameworks for mapping Java classes (models) to a relational database. The question is what we should choose for our Java application and why. A comparison between the most used relational database management systems, mixed with the most used frameworks should give us some guidance about when to use what. The evaluation is done on timing for each CRUD operation, from thousands to millions of entries, using the possible combinations between the relational database system and the framework. The experiments included the possibilities to warm up the Java Virtual Machine before the execution of the queries. Also, the research investigated the time spent inside different methods of the code, to determine the critical regions. Thus, the conclusions provide a comprehensive overview of the performances of Java applications accessing databases depending on the suite of decisions considering the database type, the framework in use, the type of operation, and supporting architects and developers for their technological decisions and for improving the speed of their programs.

Arctic ozone amount in winter to spring shows large year-to-year variation. This study investigates Arctic spring ozone in relation to the phase of quasi-biennial oscillation (QBO)/the 11-year solar cycle, using satellite observations, reanalysis data, and outputs of a chemistry climate model (CCM) during the period of 1979–2011. For this duration, we found that the composite mean of the Northern Hemisphere high-latitude total ozone in the QBO-westerly (QBO-W)/solar minimum (Smin) phase is slightly smaller than those averaged for the QBO-W/Smax and QBO-E/Smax years in March. An analysis of a passive ozone tracer in the CCM simulation indicates that this negative anomaly is primarily caused by transport. The negative anomaly is consistent with a weakening of the residual mean downward motion in the polar lower stratosphere. The contribution of chemical processes estimated using the column amount difference between ozone and the passive ozone tracer is between 10–20% of the total anomaly in March. The lower ozone levels in the Arctic spring during the QBO-W/Smin years are associated with a stronger Arctic polar vortex from late winter to early spring, which is linked to the reduced occurrence of sudden stratospheric warming in the winter during the QBO-W/Smin years.

Drying grains in a fixed bed can be an interesting alternative to prevent undesirable breaks and fractures of solids due to mechanical shocks, something that cannot be avoided when drying in moving beds. A disadvantage of fixed bed drying is that there can be significant gradients in the critical variables if the layer of particulate solids is thick. This work shows that periodically changing the direction of drying air flow is an effective technique to reduce differences within the bed and allow better uniformity of the product. Drying in a thick layer of 10 cm of sorghum grains was carried out at 50 and 60oC for air flow velocity of 2.1 m.s-1. The results showed that despite increasing the total drying time, the technique actually allowed a significant decrease in the temperature gradients and moisture content of the sorghum grains. The change in direction of the air flow caused the drying front to be displaced, sometimes towards the top, sometimes towards the base of the bed. At 50oC, drying lasted a total of 240 min, bringing the sorghum grains to an average overall moisture content of 0.13 on a dry basis.

Rice provides ~20% of human dietary energy and, for many people, a similar share of their protein. Rice cultivation, however, produces significant greenhouse gas (GHG) emissions, comparable to those from the aviation sector. The main GHG from rice production is methane, mostly a result of conventional rice cultivation (CRC) keeping rice fields continuously flooded during the crop cycle. There is extensive evidence that alternate wetting and drying (AWD) of rice fields substantially reduces methane emissions. AWD is one component of the System of Rice Intensification (SRI), an agroecological approach to the management of plants, water, soil and nutrients practiced by millions of farmers in both lowland irrigated rice and upland rainfed cultivation. Thirteen countries have included SRI in their Nationally Determined Contributions to GHG reduction or climate change mitigation. This article reviews 16 field studies of the net reduction in GHG emissions from the adoption of AWD, eight from the adoption of SRI, and two that compared SRI and AWD. Where available, the review includes data on yield and therefore on carbon dioxide-equivalent GHG emissions per kilogram of rice produced. The evidence indicates that AWD and SRI offer a similar and substantial reduction (~35–41%) in GHG emissions per hectare compared with conventional rice cultivation. However, SRI offers ~66% greater yield than CRC, and therefore greater reduction in emissions per kilogram of rice, ~54% more than AWD. The limited data directly comparing SRI and AWD support this finding. SRI also appears to have greater potential to sequester carbon in the soil. SRI lowers rice farmers’ costs of production, adds to their income and can make climate-friendly methods more attractive. Both AWD and SRI are greatly preferable to current conventional practices, but SRI offers opportunities to contribute to food security while directly addressing the drivers of climate change.

Traditional metals such as stainless steel, titanium and cobalt chrome are used in biomedical applications (implants, scaffolds etc.) but suffer from issues such as osseointegration and compatibility with existing bone. One way to improve traditional biomaterials is to incorporate ceramics with these metals so that their mechanical properties can be similar to cortical bones. Tricalcium phosphate is such a ceramic with properties so that it can be used in human body. This research explores the use of binder jetting based additive manufacturing process to create a novel biocomposite made of cobalt chrome and tricalcium phosphate. Experiments were conducted and processing parameters were varied to study their effect on the printing of this biocomposite. Layer thickness, binder saturation and drying time affected the dimensional tolerance and the density of the green samples. This effect is important to understand so that the material can be optimized for use in specific applications.

Iron (Fe) and zinc (Zn) deficiency in cereal grains has deleterious effects on the health of millions of people, especially in developing countries. As wheat, as a staple crop, is consumed in large quantities, its micronutrient content is important. Crops in Africa are often grown under low nitrogen (N) and low phosphorous (P) conditions. The aim of this study was to determine the effect of low N and low P stress on Fe and Zn and phytic acid concentration, in two commercial spring wheat cultivars with excellent baking quality. The two cultivars did not differ significantly for the measured characteristics. Across all treatments the average values for Fe varied between 19.60-28.61 mg kg^-1, Zn between 17.68-33.79 mg kg^-1 and phytic acid between 5.03-6.92 mg g^-1. Low P stress lead to the highest values of Fe and Zn, and the lowest value for phytic acid. Phytic acid:Fe and phytic acid:Zn ratios were also highly significantly reduced under low P stress conditions. Low N conditions caused significantly increased Zn levels. Despite this, the phytic acid:Fe and phytic acid:Zn ratios were relatively high under all conditions, indicating a low bioavailability of both Fe and Zn in these wheat cultivars.

Porous β-tricalcium phosphate (Ca3(PO4)2; β-TCP) was prepared by freeze-drying and the effects of this process on pore shapes and sizes were investigated. Various samples were prepared by freezing β-TCP slurries above a liquid nitrogen surface at −180 °C with subsequent immersion in liquid nitrogen at −196 °C. These materials were then dried under reduced pressure in a freeze-dryer after which they were sintered by heating. Compared with conventional heat-based drying, the resulting pores were more spherical, which increased both the mechanical strength and porosity of the β-TCP. These materials had a wide range of pore sizes from 50 to 200 µm, with the mean and median values both approximately 100 µm regardless of the freeze-drying conditions. Mercury porosimetry data showed that the samples contained small, interconnected pores with sizes of up to 1.24 µm and macroscopic, interconnected pores up to 25.8 µm in size. The effects of non-ionic surfactants having different hydrophilic/lipophilic balance (HLB) values on foaming and pore size were also investigated. Materials made with surfactants having lower HLB values exhibited smaller pores and lower porosity whereas higher HLB surfactants gave higher porosity and slightly larger macropores. Even so, the pore diameter could not be readily controlled solely by adjusting the HLB value. The findings of this work indicated that high porosity (75%) and good compressive strength (&gt;2 MPa) can both be obtained in the same porous material and that foaming agents with HLB values between 12.0 and 13.5 were optimal.

Chestnut is an interesting productive alternative for farmers in Southern Chile. However, cli-matic variability with the occurrence of late spring and early summer frost have cause damages on young trees. Glycine‒betaine (GB) spraying on shoots of sensitive chestnut induce an increase in tolerance during subsequent chilling stress. Experiment was performed on three years-old trees (cultivar Cittá di Castello) conducted in a leader training system and sprayed with com-mercial GB (120 g hL‒1). In summer trees treated with GB showed a better recovery after the frost (‒2.34°C) occurrence for 3.5 h compared to the control. Whereas trees obtained a 28% greater growth of central axis than untreated control (January). The trunk diameter measured in January showed the highest value under GB (27.2mm) compared with the control (25.7 mm). The GB ap-plication increased by 50 and 47% highest fresh and dry weight respectively in leaves. Under GB trees reached a 28% higher net photosynthesis (AN) compared to the AN in control (11.93 µmol CO2 m‒2 s‒1). Moreover, achieved higher stomatal conductance and transpiration rate was 44 and 31% with GB compared to control trees respectively. Antioxidant performance was differentially affected by GB activating non-enzymatic mechanisms and caused a reduced lipid peroxidation. Glycine‒Betaine has become as an interesting agronomic tool that aimed to increase tolerance to environmental stresses such as low temperatures that cause damage to herbaceous shoots and leaves in young chestnut trees.

Drought stress inducing pollen sterility can reduce crop yield worldwide. The regulatory crosstalk associated with the effects of drought on pollen formation at the cellular level have not been explored in detail so far. In this study, we performed morphological and cytoembryological analysis of anther perturbations and examined pollen development in two spring barley genotypes that differ in earliness and drought tolerance. The Syrian breeding line CamB (drought-tolerant) and the European cultivar Lubuski (drought-sensitive) were used as experimental materials to analyze the drought-induced changes in yield performance, chlorophyll fluorescence kinetics, the pollen grain micromorphology and ultrastructure during critical stages of plant development. In addition, fluctuations in HvGAMYB expression were studied, as this transcription factor is closely associated with the anthers development. In the experiments, the studied plants were affected by drought, as was confirmed by the analyses of yield performance and chlorophyll fluorescence kinetics. However, contrary to our expectations, the pollen development of plants grown under specific conditions was not severely affected. The results also suggest that growth modification, as well as the perturbation in light distribution, can affect the HvGAMYB expression. This study showed that the duration of the vegetation period can influence plant drought responses and, as a consequence, the processes associated with pollen development as every growth modification changes the dynamics of drought effects as well as the duration of plant exposition to drought.

Freeze-drying is a well-established process in biomedical engineering for the fabrication of three-dimensional open-porous medical devices, especially those based on biopolymers. One of the most used biopolymers in this field is collagen, the most abundant protein in the human body and the main component of the extracellular-matrix, as well as its derivatives. Freeze-dried collagen-based sponges with a wide variety of attributes can be produced by design and have led to a wide range of successful commercial medical devices, foremost for dental, orthopedic, hemostatic and neuronal applications. However, this is still considered a high-cost and time-consuming process that is often used in a non-optimized manner. By combining advances in other technological fields, the opportunity arises to further evolve this process in a sustainable manner, and optimize the resulting products as well as create new opportunities in this field.

The two-stage direct thermal contact (2sDTC) process is a rapid dewatering approach for fluid fine tailings (FFT) that is integrated into an oil sands bitumen extraction plant to reduce tailings pond storage and freshwater usage. In the first stage, combustion gas directly contacts atomized FFT, vaporizing water and yielding dry solids and steam-rich hot gas. The second stage involves pond effluent water directly contacting the steam-rich hot gas, recovering heat and condensing moisture. Case studies confirm the technical feasibility of the integration. Benefits include producing a dry discharge, reducing tailings water discharge and conserving an equivalent to 0.2 barrels of freshwater per barrel of oil produced. Most importantly, these benefits incur no additional energy cost to the plant as the integration eliminates the energy penalty and CO2 emissions associated with FFT dewatering. Further capacity enhancement can be achieved by using centrifuge-concentrated FFT. The study reveals that FFT concentrated to ~50 wt% solids could still maintain its pump-ability and be accommodated by the 2sDTC process, leading to an integration which could dewater more FFT annually and conserve more freshwater ( 0.58 barrels per barrel of oil produced), with the sole energy requirement being the power to drive the centrifuge machinery.

Environmental nanoparticles have been shown to exist in most aquatic environments, and environmental nanoparticles in water distribution systems significantly affect water quality. However, little research has been conducted on the environmental nanoparticles in mineral water, which is a special water resource. Nanoparticle tracking analysis (NTA) and high-resolution transmission electron microscopy (HRTEM) were conducted. This study was the first to identify many environmental nanoparticles in natural mineral water in Zibo City, Shandong Province, China. The results of the NTA showed that the concentration of the particles was 5.5 ×106 particles/mL and the peak diameter of the size distribution was 180 nm. The HRTEM showed that the nanoparticles were granular, pinniform, rodlike, and flakey in shape, and some of the nanoparticles existed in aggregation. The energy-dispersive spectrometry results showed that most of the nanoparticles contained O, Mg, Ca, Si, Fe, Ti, and P, and some of them also contained F, V, S, and Mn. When combined with the characteristics of the selected area electron diffraction pattern, the nanoparticles were confirmed to be Ca-bearing nanoparticles, attapulgite nanorods, MnO2 nanosheets, and TiO2 nanoparticles. These results indicate a new form of elements occurring in mineral water. In addition, based on the chemical and physical characteristics of the nanoparticles and mineral water, these environmental nanoparticles in the mineral water are likely to be the weathering byproducts of minerals. These nanoparticles within mineral water provide a good opportunity for understanding the behavior of nanoparticles in varied systems. Moreover, environmental nanoparticle science is important for continuing efforts in water safety, treatment, and remediation.

Transcription factors must scan genomic DNA, recognize the cognate sequence of their control element(s), and bind tightly to them. The DNA recognition process is primarily carried out by their DNA binding domains (DBD), which interact with the cognate site with high affinity and more weakly with any other DNA sequence. DBDs are generally thought to bind to their cognate DNA without changing conformation (lock-and-key). Here we used nuclear magnetic resonance and circular dichroism to investigate the interplay between DNA recognition and DBD conformation in the Engrailed homeodomain (EnHD), as model case for the homeodomain family of eukaryotic DBDs. We found that the conformational ensemble of EnHD is rather flexible and becomes more structured as ionic strength increases following a Debye-Hückel’s dependence. Our analysis indicates that EnHD’s response to ionic strength is mediated by a built-in electrostatic spring-loaded latch that operates as conformational transducer. We also found that, at moderate ionic strengths, EnHD changes conformation upon binding to cognate DNA. This change is of larger amplitude and somewhat orthogonal to the response to ionic strength. As a consequence, very high ionic strengths (e.g. 700 mM) block the electrostatic-spring-loaded latch and binding to cognate DNA becomes lock-and-key. However, the interplay between EnHD conformation and cognate DNA binding is robust across a range of ionic strengths (i.e. 45 to 300 mM) that covers the most physiologically-relevant conditions. Therefore, our results demonstrate the presence of a mechanism for the conformational control of cognate DNA recognition on a eukaryotic DBD. This mechanism can function as a signal transducer that immediately locks the DBD in place upon encountering the cognate site during active DNA scanning. The electrostatic-spring-loaded latch of EnHD can also enable the fine control of DNA recognition in response to local/temporal changes in ionic strength induced by variate physiological processes.

With the changing climate, there is an increasing emphasis on drought-resistant varieties including the ability to maintain quality production. As there is also interest in ancient wheat varieties, the aim of this study was to evaluate the ancient Khorasan (Kamut ®) with the modern Kabot spring wheat variety using remote sensing data. Images from unmanned aerial vehicles during four growing seasons were processed. Based on vegetation indices, the growth of these varieties and their response to meteorological conditions were evaluated, as well as the ability to resist drought and higher temperatures with respect to specific soil conditions under conventional (CT), minimum (MTC) and minimization (MTD) tillage. It was found that the Khorasan had the lowest values of the vegetation indices on the CT variant in the dry years 2022 and 2023. On the contrary, in the previous wet years 2020 and 2021, both varieties showed similar results. Regarding to water stress, the CT variant was also the least suitable for ancient Khorasan (average CWSI = 0.38). On the contrary, this variant seems to be suitable for the modern Kabot variety (CWSI = 0.29), while no significant difference between tillage variants was found for this variety. In general, water stress was easily detectable by the observed parameters in the growth phase of stem elongation (R2 up to 0.88).

In dry season paddy farming, the alternate wetting and drying (AWD) irrigation improves water productivity, paddy production, and has the potential to decrease greenhouse gas (GHG) such as methane (CH4) and nitrous oxide (N2O) emissions when compared to continuous flooding (CF). However, there is a lack of research in Bangladesh on the effects of water management on CH4 and N2O emissions. During November 2017–April 2018, participatory on-farm trials were conducted at Feni and Chattogram districts of Bangladesh. Total 105 farmers comprising 20-hectare of land (62 farmers at Feni and 43 farmers at Chattogram district, each location having 10 hectare of land). We compared irrigation water and cost reductions, paddy yield, and CH4 and N2O emissions from paddy fields irrigated using AWD and CF irrigation methods. The CH4 and N2O emissions were determined using the Cool Farm Beta-3 methodology, and the global warming potential (GWP) was estimated using the Intergovernmental Panel on Climate Change-2014 standard approach. The mean results of randomly selected 30 farmers from two locations (15 of each) showed that AWD remarkably decreased irrigation water consumption by about 24% and increased water productivity by 224%. We estimated 23% savings for irrigation costs in AWD. By this time, AWD improved paddy production by 3% over CF. The AWD irrigation resulted in a 47% reduction in cumulative CH4 emissions having a lower CH4 emission factor (0.74 kg ha-1 day-1) than CF (1.39 kg ha-1 day-1). There was no obvious difference in N2O emission between AWD and CF. When compared to CF, AWD decreased the overall GWP by 27% and lowered the GHG intensity by 42%. The CH4 and N2O emissions did not differ substantially between Feni and Chattogram.

Transport of carbon, major and trace element by rivers in permafrost-affected regions is one of the key factor of circumpolar aquatic ecosystem response to climate warming and permafrost thaw. While seasonal and annual export fluxes (yields) of carbon (C) and inorganic solutes are fairly well known for all large Arctic rivers, spatial variations in elementary concentration along the river length and among its tributaries remain poorly understood. Moreover, the landscape factors controlling riverine element concentration in permafrost-affected regions are still poorly constrained. This is especially true for the largest river of Eastern Siberia, the Lena River, which drains through continuous permafrost zones with highly variable lithology and vegetation. Here we present the results of C, major and trace element measurements over a 2600-km transect of the Lena River main stem (upper and middle reaches) including its 30 tributaries, conducted at the peak of the spring flood. There were two main group of solutes in the main stem depending on their spatial pattern: i) elements that decreased their concentrations downstream, from SW to NE (Cl, SO4, DIC, Li, B, Na, Mg, K, Ca, As, Sr, Mo, Sb, Ba and U), which probably reflected a decrease in the proportion of carbonate rocks in the watershed and the degree of groundwater feeding, and ii) elements that increased their concentrations downstream (Al, Ti, Cr, Fe, Ga, Rb, Y, Zr, Nb, Cs, REEs, Hf and Th), which was tentatively linked to an increase in organic C stock in soils, larch forest coverage and enhanced mobilization of lithogenic elements from silicate soil minerals. Based on landscape parameters of Lena tributaries, we tested the impact of major environmental factors on major and trace element spatial pattern. Among all the variables, the proportion of sporadic permafrost on the watershed strongly controlled concentrations of soluble highly mobile elements (Cl, B, DIC, Li, Na, K, Mg, Ca, Sr, Mo, As and U). Another important factor of element concentration control in the Lena River tributaries was the coverage of watershed by light (B, Cl, Na, K, U) and deciduous (Fe, Ni, Zn, Ge, Rb, Zr, La, Th) needle-leaf forest (pine and larch). The latter, however, could also reflect the DOC-enhanced transport of low-soluble trace elements in the NW part of the basin. This part of the basin is dominated by silicate rocks and continuous permafrost, as compared to carbonate rock-dominated and groundwater-affected SW part of the Lena River basin. Overall, the impact of rock lithology and permafrost on major and trace solutes of the Lena River basin during the peak of spring flood was mostly detected at the scale of the main stem. Such an impact for tributaries was much less pronounced, because of the dominance of surface flow and lower hydrological connectivity with deep groundwater in the latter. Future changes in the river water chemistry linked to climate warming and permafrost thaw at the scale of the whole river basin are likely to be linked to changes in spatial pattern of dominant vegetation, rather than to the permafrost regime. We argue that comparable studies of large, permafrost-impacted rivers during most contrasting seasons, including winter baseflow, should allow efficient prediction of future changes in riverine ‘inorganic’ hydrochemistry induced by permafrost thaw.

The fluctuations in both time and space of the fish larvae community in relation to hydrographic characteristics in the waters surrounding the Taiwan Bank were studied in October 2021 (autumn) and March 2022 (spring). Throughout the study period, we identified a total of 149 taxa of fish larvae, encompassing 96 genera and 71 families. Engraulis japonicus, Diaphus slender type, unidentified Gobiidae, Apogon sp., unidentified Clupeidae, and Benthosema pterotum were the six most dominant taxa, together constituted 47.39% of the total catch. No significant temporal difference in abundance of fish larvae was found, but the species number of fish larvae was more diverse in spring than in autumn. There was a notable difference in species composition between the cruises, and the cluster analysis unveiled a distinct temporal structure in the assemblage of fish larvae. The dynamics of prevailing currents induced by seasonal monsoons play an important role in the transport of fish larvae. The distribution of fish larvae was closely linked to hydrographic features, where seawater temperature and salinity emerged as the primary explanatory factors influencing the composition of fish larvae assemblages in the waters surrounding the Taiwan Bank. While the increased influx of nutrients from upwelling ensures abundant food availability, the hydrographic conditions may not be suitable for every fish larva.

Abstract: Thermostability of vaccines, particularly enveloped viral vectored vaccines, remains a challenge for their delivery wherever needed. Freeze-drying of viral vectored vaccines is a prom-ising approach but remains challenging due to the water removal process from the outer and in-ner parts of the virus. In the case of enveloped viruses, freeze-drying induces increased stresses on the envelope, which often leads to inactivation of the virus. In this study, we design a method to freeze-dry a recombinant Vesicular Stomatitis Virus (VSV) expressing the SARS-CoV-2 spike glycoprotein. Since the envelope of VSV is composed of 50% lipid and 50% protein, the formula-tion study focused on both the protein and lipid portions of the vector. Formulations were pre-pared primarily using sucrose, trehalose, and sorbitol as cryoprotectants; mannitol as a lyopro-tectant; and histidine as a buffer. Initially, the infectivity of rVSV-SARS-CoV-2 and cake stability were investigated at different final moisture contents. High recovery of the infectious viral titer ( 0.5 to 1 log loss) was found at 3-6% moisture content with no deterioration of the freeze-dried cakes. To further minimize infectious viral titer loss, the composition and concentration of the ex-cipients were studied. An increase from 5 to 10% of both cryoprotectants and lyoprotectant, to-gether with the addition of 0.5% gelatin, resulted in the improved recovery of infectious virus titer and stable cake formation. Moreover, the secondary drying temperature of the freeze-drying pro-cess showed a significant impact on the infectivity of rVSV-SARS-CoV-2. The infectivity of the vector declined drastically when the temperature was raised above 20°C. Throughout a long-term stability study, formulations containing 10% sugar (sucrose/trehalose), 10% mannitol, 0.5% gelatin, and 10 mM of histidine showed satisfactory stability for six months at 2-8°C. The development of this freeze-drying process and the optimized formulation minimizes the need for a costly cold chain distribution system.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

This paper presents tea leaves moisture monitoring system based on RF reflectometry techniques. The system was divided into two parts which are the sensor and reflectometer parts. The large coaxial probe was used as a sensor of the system. The reflectometer part plays a role as signal generator and also data acquisition. The reflectometer-sensor system was operated with a graphical user interface at 1.529 GHz at room temperature. The system was able to measure the moisture content of tea leaves ranging 0% m.c to 50% m.c on a wet basis. In this study, up to five kinds of tea leaves bulk were tested. The mean of absolute errors in the moisture measurement for tea leaves was ±2.

Surface area and pore size distribution of Eucalyptus samples pretreated by different methods were determined by the Brunauer-Emmett-Teller (BET) technique. Three methods were applied to prepare cellulosic biomass samples for BET measurements: air, freeze, and critical point drying (CPD). Air and freeze drying caused severe collapse of biomass pore structures, but CPD effectively preserved biomass morphology. Surface area of CPD prepared Eucalyptus samples was determined to be 58–161 m2/g, whereas air and freeze dried samples were 0.5–1.3 and 1.0–2.4 m2/g, respectively. Average pore diameter of CPD prepared Eucalyptus samples were 61–70Å. CPD preserved Eucalyptus sample morphology by replacing water with a non-polar solvent, CO2 fluid, which prevented hydrogen bond reformation in the cellulose.

Water availability is a major constraint for spring wheat production on the western Loess Plateau of China. The impact of tillage practices on water potential, water potential gradient, water transfer resistance, yield, and water use efficiency (WUEg) of spring wheat was monitored on the western Loess Plateau in 2016 and 2017. Six tillage practices were assessed, including conventional tillage with no straw (T), no-till with straw cover (NTS), no-till with no straw (NT), conventional tillage with straw incorporated (TS), conventional tillage with plastic mulch (TP), and no-till with plastic mulch (NTP). No-till with straw cover, TP, and NTP significantly improved soil water potential and root water potential at the seedling stage and leaf water potential at the seedling, tillering, jointing, and flowering stages, compared to T. These treatments also significantly reduced the soil-leaf water potential gradient at the 0-10 cm soil layer at the seedling stage and at the 30-50 cm soil layer at flowering, compared to T. Thus, NTS, TP, and NTP reduced soil-leaf water transfer resistance and enhanced transpiration. Compared to T, the NTS, TP, and NTP treatments significantly increased biomass yield (BY) by 18, 36, and 40%, respectively, and grain yield (GY) by 28, 22, and 24%, respectively, with corresponding increases in WUEg of 24, 26, and 24%, respectively. These results demonstrate that NTS, TP, and NTP improved GY and WUEg of spring wheat by decreasing the soil-leaf water potential gradient and soil-leaf water transfer resistance and enhancing transpiration, and are suitable tillage practices for sustainable intensification of wheat production in semi-arid areas.

Keywords: grape pomace extracts, encapsulation, freeze-drying, bioaccessibility, phenolic compounds

Grape pomace is a byproduct of wineries and sustainable source of bioactive phenolic compounds. Encapsulation of phenolics with a well-chosen coating may be a promising means of delivering them to the intestine, where they can then be absorbed and exert their health-promoting properties. Ionic gelation of grape pomace extract with natural coatings (sodium alginate and its combination with maltodextrins, gelatin, chitosan, tragacanth gum, and gum arabic) was performed, and the resulting hydrogel microbeads were then air-, vacuum-, or freeze-dried to prevent their spoilage. The physicochemical characterization (size, shape, texture, and morphology) of the microbeads and the in vitro release of phenols from microbeads were studied and a good relationship between them was established. Freeze-dried microbeads showed the highest cumulative release of phenols as in the intestinal phase (23.31 – 43.27 mgGAE/gMB), followed by vacuum-dried (23.31 - 35.41 mgGAE/gMB) and air-dried (22.74 – 31.38 mgGAE/gMB), while the most suitable release dynamics in the intestinal phase were observed for alginate-based microbeads combined with gelatin (58.4 %), gum arabic (34 %) and 1.5 % w/v chitosan (15.3 %). The results highlight the importance of developing encapsulated formulations containing a natural source of bioactive compounds that can be used in various functional foods and pharmaceutical products.

In regenerated oak forests, weeds are present throughout the year, the ones appearing in early spring representing a major problem. Hence, the aim of this study was to examine herbicides for early spring broadleaved weed control in the regenerated oak forests while the seedlings are in a dormant stage. During 2019 and 2020 two experiments were set up in regenerated pedunculate oak forests with 2-yar and 3-year-old seedlings and two herbicides were applied in two doses: fluroxypyr at dose 360 g a.i. ha-1 and 540 g a.i. ha-1 and clopyralid at dose 100 g a.i. ha-1 and 120 g a.i. ha-1. The results from the two-year investigations showed that fluroxypyr and clopyralid significantly reduced early spring broadleaved weeds in the regenerated pedunculate oak forests but both doses of fluroxypyr provided greater control of presented weeds than the applied doses of clopyralid. The manual weeding reduced broadleaved weeds in experiments, but that method did not have a long-term effect on the reduction of weeds. Applied doses of herbicides fluroxypyr and clopyralid did not cause phytotoxicity symptoms in dormant oak seedlings. All investigated treatments significantly reduced fresh broadleaved weed biomass compared to the control. Generally, it can be concluded that fluroxypyr and clopyralid can be successfully used for control of many early spring broadleaved weeds in the regenerated pedunculate oak forests, but oak seedlings must be in the dormant stage.

This study aimed to analyze areas of concern and support of the Austrian general population two years into the COVID-19 pandemic. A representative sample (N = 1,031) of the Austrian general population was surveyed online between April 19 and 26, 2022. A qualitative study design was used to explore the factors of most considerable current concern (question 1) and the most important sources of support (question 2). The responses to the two open-ended questions were evaluated using conventional content analysis and categories were formed according to the frequency of the answers. The analysis revealed that inflation and finances (30% of participants) and the war in Ukraine (22%) were the greatest sources of concern, followed by mental health (10%), and physical health (10%). Factors such as social contacts within and outside the family were mentioned most frequently as sources of support (36% of participants), followed by recreational activities (23%) and attitudes and abilities (22%). Compared to data collected at the end of the first year of the pandemic (between December 23, 2020, and January 4, 2021), concerns about one's financial situation was now mentioned more frequently (30,4% vs. 8,5%). On the other hand, different types of pandemic-related concerns were less often mentioned. Social contacts and recreation were mentioned as the most important sources of support at both time points (46% and 36% of the participants). Results suggest that the economic concerns are lagging behind the restrictions imposed by the pandemic. In addition, the impending war in Ukraine seems to have a relevant impact on mental health in Austria. Further nuanced qualitative research, particularly involving vulnerable groups like low-income individuals and the unemployed, is crucial.

Water resources worldwide are limited, especially in desert areas like Saudi Arabia. Therefore, the rational and sustainable management of irrigation water supply is an imperative required by the conditions of space and time. This study evaluates the irrigation system through partial root-zone drying (PRD) and regulated deficit irrigation (RDI). The effect of applying the PRD and RDI systems on the efficiency and rationalization of irrigation water consumption in a greenhouse and open field cucumber was studied in addition to using the surface (S) and subsurface (SB) drip irrigation methods on irrigation efficiency. The productivity of the RDI-S regular drip irrigation treatment was considered 100% as the control on which the results of all treatments are measured. The results showed that in terms of irrigation technique, the PRD-SB technique had the highest productivity during the winter season in greenhouse cucumbers, with a general average of 13.8 kg m-2 for all irrigation levels, while the RDI-SB technique had the highest productivity during the summer season, with a general average of 16.1 kg m-2. Regarding irrigation level results, the study showed that an irrigation level of 100% is the highest productivity in all irrigation techniques, with a general average of 14.9 kg m-2 for all irrigation techniques during the winter season and 16.4 kg m-2 during the summer. However, the increase in the irrigation level to 150% did not increase productivity. In comparison, the application of the deficit irrigation technique by reducing the level of irrigation to 50% was not accompanied by a similar decrease in productivity. The study results also showed that irrigation with the PRD-SB system was the most productive in the open field at all irrigation levels, with a general average of 7.3 kg m-2. The general average of the percentage decrease in productivity in all irrigation techniques compared to reducing the irrigation percentage to 50% and 75% was 22% and 3 %. The irrigation efficiencies were higher when applying the PRD (PRD-SB) in winter. In contrast, applying a deficit irrigation system (RDI-SB) in the summer season had the highest efficiency. It could be concluded that using PRD and RDI systems for indoor and outdoor cucumber can save irrigation water.

Cocoa beans of the CCN-51 clone harvested in the Tumaco region (Nariño, Colombia) were fermented following four different treatments: (1) spontaneously (at room temperature for 120 h) in traditional conditions (Control); (2) traditional processing with a pre-drying (sun-dried for 24 h) treatment (PD); (3) with fermentation (for 120 h) after inoculation of a yeast starter culture (YS); and (4) including both treatments, pre-drying and yeast inoculation (PD+YS). Chemical composition, fatty acids, total polyphenol, methylxanthines (theobromine and caffeine) and lactic acid content of cocoa beans were determined. Chemical and fatty acid composition and theobromine content were not affected by the different fermentation treatment applied. When analysing total polyphenol content, YS and PD+YS treatments significantly increased the content of these compounds at the end of the fermentation process, while PD treatment decreased the caffeine content of cocoa beans. Finally, lactic acid content decreased as a consequence of both inoculation of yeast starter and mainly the pre-drying treatment. In conclusion, solar pre-drying in the open air and the inoculation of a yeast starter treatments could improve the final quality of coca beans.

This study aims to evaluate the effect of different drying methodologies (room, microwave, convective, oven and freeze-drying) on the chemical composition, the microbiological quality of extracts and the biological activities namely clotting milk and antioxidant activities for both spontaneous and cultivated Onopordum nervosum ssp. platylepis. The results showed that the drying methodology has significantly affected the phenolic composition. Freeze dried flowers showed the best amounts of total phenols, flavonoids and condensed tannins followed by the microwave dried flowers. However, the latest presented the lowest protein content. Finally, the biological activities were significantly dependent on the used drying process. The effective concentration EC50 values let to classify the samples according to their decreasing power to inhibit DPPH free radicals: dryer<oven<room <microwave<freeze-drying. The drying process significantly affected the clotting milk activity, freeze dried flowers showed the highest activity. All the obtained results do not reveal a significant difference between cultivated and spontaneous plants.

To investigate the effect of nitrogen (N) application on carbon metabolism and yield of flag leaves and grains of spring wheat under drip irrigation in Xinjiang, a split - plot design was adopted from 2020 to 2021, with strong gluten wheat Xinchun 37 (XC37) and medium gluten wheat Xinchun 6 (XC 6) as the main plot factor and different nitrogen application rates as subplot factor. Four nitrogen application rates of 0, 210, 255 and 300 kg·hm-2 (CK2, B1, A1 and CK1, respectively) were set to analyze and compare the nitrogen response of key enzyme activity, soluble sugar, sucrose and starch content in flag leaves and grains to control yield formation. The results showed that with the increase of nitrogen application, Sucrose phosphate synthetase (SPS) and sucrose synthetase (SS) in flag leaves, SS in seeds, activities of adenosine diphosphate pyrophosphorylase (ADPG - PPase), soluble starch synthase (SSS), bound starch synthase (GBSS) and starch branching enzyme (SBE) in seeds, contents of soluble sugar and sucrose and yield in flag leaves increased first increasing and then decreasing. The A1 treatment (255 kg·hm-2) showed significant differences compared to other treatments, with increases of 7.95–158.33%, 8.69–155.12%, 7.65–53.25%, 5.41–62.83%, 2.85–85.52%, 3.08–57.30%, 8.87–79.16%, 9.33–196.55%, 9.43–112.78%, and higher levels of amylose, amylopectin, and total starch content than other treatments by 1.86–30.38%, 10.58–83.69%, and 7.96–63.09%, respectively. Correlation and stepwise regression analysis indicate highly significant positive correlation between yield and solube sugar and sucrose of flag leaves and grains, as well as their key emzymes and starch. Among them, soluble sugar in grains, amylopectin, and sucrose in grains have the greatest impact on the yield of XC37, determining 84.5% of its yield. SSS, soluble sugars in grains, amylopectin, and SBE have the greatest impact on the yield of XC 6, determining 80.4% of its yield. The starch shows a highly significant positive correlation with ADPG - PPase, SSS, GBSS, and SBE. There is a significant interaction effect between nitrogen application rate and variety, with better performance observed in Xinchun 37 compared to Xinchun 6. Under drip irrigation conditions in arid areas, nitrogen application of 255 kg·hm-2 can effectively regulate the metabolism of sucrose to starch in flag leaves and grains of spring wheat, which is conducive to the accumulation of starch in grains and the formation of yield.

The boreal Hemisphere has been experiencing increasing extreme hot and dry conditions over the past few decades, consistent with anthropogenic climate change expectations. The continental extension of the phenomenon calls for tools and techniques capable of monitoring the global to regional scales. In this context, the satellite is the only system that can satisfy the need for global coverage. The main objective we have addressed in the present paper is the capability of infrared satellite observations helping to monitor the vegetation stress due to increasing drought and heatwaves in summer. We have designed and implemented a new water deficit index (wdi) that exploits satellite observations in the infrared to retrieve humidity, air temperature, and surface temperature simultaneously. These three parameters are combined to provide the water deficit index. The index has been developed based on the Infrared Atmospheric Sounder Interferometer or IASI, which covers the infrared spectral range 645 to 2760 cm-1 with a sampling of 0.25 cm-1. The index has been used to study the 2017 heatwave, which hit Continental Europe from May to October. In particular, we have examined Southern Italy, where Mediterranean forests suffer from climate change. We have computed the index's time series and show that it can be used to indicate the atmospheric background conditions associated with meteorological drought. We have also found a good agreement with soil moisture, which suggests that the persistence of anomalously high water deficit index was an essential driver of the rapid development and evolution of the exceptionally severe 2017 droughts.

In the industrial production of olive oil, both solid wastes and those produced from their incineration are a serious environmental problem since only 20% w/w of the fruit becomes oil and the rest is waste, mainly orujo and alperujo. A key aspect to transform these wastes into an important source of energy such as pellets is to recognize the most appropriate time of the year for waste drying, with the objective of minimizing the environmental impact of the volatile compounds contained in the waste. In this work, the emissions produced during thermal-mechanical drying were studied along a period of six months of waste storage in which alperujo and orujo were stored in open containers under uncontrolled environmental conditions. The studied emissions were produced when both wastes were dried in a pilot rotary drying trommel at 450ºC to reduce their initial humidity of around 70-80% w/w to 10-15% w/w. Results indicated that when the storage time of the wastes in uncontrolled environments increases, the emission of odorant compounds during drying also increases as a consequence of the biological and chemical processes occurring in the containers during waste storage. The main odorant VOCs were quantified monthly for six months at the outlet of the drying trommel. It was determined that the drying of this type of waste can be carried out properly until the third month of storage. Afterwards, the concentration of most VOCs produced widely exceeded the odor thresholds of selected compounds.

The coronavirus (COVID-19) pandemic was particularly invasive in Italy during the period between March and late April 2020 then decreased in both in the number of infections and in the seriousness of the illness throughout the summer of 2020. In this discussion, we measure the severity of the disease by the ratio of Intensive Care Units (ICU) spaces occupied by COVID-19 patients and the number of Active Cases (AC) each month from April to October 2020. We also use the ratio of the number of Deaths (D) to the number of Active Cases. What clearly emerges, from rigorous statistical analysis, is a progressive decrease in both ratios until August, indicating progressive mitigation of the disease. This is particularly evident when comparing March-April with July-August; during the summer period the two ratios became roughly 18 times lower. We test such sharp decreases against possible bias in counting active cases and we confirm their statistical significance. We then interpret such evidence in terms of the well-known seasonality of the human immune system and the virus-inactivating effect of stronger UV rays in the summer. Both ratios, however, increased again in October as ICU/AC began to increase in September 2020. These ratios and the exponential growth of infections in October indicate that the virus - if not contained by strict measures - will lead to unsustainable challenges for the Italian health system in the winter of 2020-2021 .

Species belonging to the Bauhinia genus, usually known as "pata-de-vaca", are popularly used to treat diabetes. Among them is Bauhinia ungulata var. obtusifolia (Ducke) Vaz, whose leaves are used, as a tea, for medicinal purposes in the Amazon region. The microencapsulation of the aqueous extract of its leaves, containing phenolic compounds, using five different wall materials (maltodextrin: DE11-14, and DE4-7; β-cyclodextrin; pectin, and sodium carboxymethylcellulose) is described in this paper. The microstructure, particle size, thermal behavior, yield, and encapsulation efficiency were investigated and compared using different techniques. Using high-performance liquid chromatography, phenolics, and flavonoids were detected and quantified in the microparticles. Microparticles, obtained with yield and phenolics encapsulation efficiency ranging between 60-83 % and 35-57 %, respectively, showed a particle size distribution between 1.15 and 5.54 µm, spherical morphology, and wrinkled surface. Among them, those prepared with sodium carboxymethylcellulose and pectin proved to be thermally the most stable. They had the highest flavonoid content (23.07 and 21.73 mgRUTE/g Extract) and total antioxidant activity by both the DPPH· (376.55 and 367.86 µmolTrolox/g Extract) and ABTS·+ (1085.72 and 1062.32 µmolTrolox/ g Extract) assays. The chromatographic analyses allowed for quantification, in the microparticles, chlorogenic acid (1.67-1.98 mg/g Extract), p-coumaric acid (0.06-0.08 mg/g Extract), rutin (11.1-12.9 mg/g Extract) and isoquercitrin (0.47-0.53 mg/g Extract), compounds considered responsible for the antidiabetic property attributed to the species.

Freeze drying was compared with spray drying regarding feasibility to process wild thyme drug in order to obtain dry formulations at laboratory scale starting from liquid extracts produced by different extraction methods: maceration, heat-, ultrasound-, and microwave-assisted extractions. Higher powder yield (based on the dry weight prior to extraction) was achieved by freeze than spray drying and lower loss of total polyphenol content (TPC) and total flavonoid content (TFC) due to the drying process. Gelatin as a coating agent (5% w/w) provided better TPC recovery by 70% in case of lyophilization and higher powder yield in case of spray drying by diminishing material deposition on the wall of the drying chamber. The resulting gelatin-free and gelatin-containing powders carried polyphenols in amount ~190 and 53-75 mg gallic acid equivalents GAE/g of powder, respectively. Microwave-assisted extract formulation distinguished from others by higher content of polyphenols, proteins and sugars, higher bulk density and lower solubility. The type of the drying process affected mainly position of the gelatin-derived -OH and amide bands in FTIR spectra. Spray dried formulations compared to freeze dried expressed higher thermal stability as confirmed by differential scanning calorimetry analysis and higher diffusion coefficient; the last feature can be associated with the lower specific surface area of irregularly shaped freeze-dried particles (151-223 µm) compared to small microspheres (~8 µm) in spray-dried powder.

We used flow cytometry to follow diel variations of viruses, picoplankton, and nanoflagellates for 2 days with about 4 hours of temporal sampling in spring 2024 in coastal surface waters of the subtropical western Pacific. An event of wind change, associated with rainfall and increased turbulence, disrupted diel patterns of the overall microbial communities during the second cycle. We observed that bacterial abundance did not follow a consistent diel pattern and that viral abundance was positively correlated with bacterial abundance. Synechococcus spp. and Prochlorococcus spp. grew during the light period and with peak abundance at night, exhibited marked diel variability, however, opposite patterns were observed in picoeukaryotes. According to Synechococcus spp. and Prochlorococcus spp. diel changes, nanoflagellate grazing could control their abundances and may explain temporally varying picocyanobacterial abundances. As we observed in the culture experiments, the results showed a significant increase in picoeukaryotic abundance from noon to nighttime, and a decrease in bacterial abundance during nighttime, to show the prey-predator cycle. Our study suggests picoeukaryotes could serve as bacteria predators by being mixotrophs. Future studies aiming to understand the interactions between prokaryotes and picoeukaryotes within marine microbial communities should take these differences into account.

Wheat yield plays an important role in the global economy. Changing climate conditions and increased drought negatively affect grain yield. Currently, breeding programs are aimed at improving wheat productivity. To accelerate the selection process of hybrids and parental forms for crosses, it is essential to pay attention to plants' phenotypic and genetic potential. We studied the genes of the "green revolution" group Rht and coarse-grained TaGW and TaGS to increase yields by selecting optimal parameters for wheat. We focused on short-stemmed and coarse-grained characteristics in a dry climate and conducted a correlation analysis between the genetic potential of wheat varieties and hybrids and their phenotypic manifestation in drought conditions. Rht-D1b significantly reduced the height of plants by 51.67% and reduced the coleoptile length by 30.45%. At the same time, TaGW8-B1a increased the grain width by 13.37%. However, in the presence of Rht-D1b and Rht-B1b in the genome, the 1000-kernal weight was 35.06 g (p<0.05), the Rht-B1b gene enhanced it by 9% (p<0.05), while both Rht-D1a and Rht-B1a alleles gave a 1000-kernal weight of 37.96 g (p<0.05). The Rht-D1b and Rht-B1b alleles gave 18.5 seeds per ear, while the Rht-D1a and Rht-B1a alleles gave the value of grains per ear -24.1 pcs. The data obtained indicated the relationship of phenotypic and genetic parameters in wheat between the coarse-grained and short-stemmed genes, which makes it possible to select based on the genetic parameters of varieties and hybrids, thereby speeding up the selection process.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.