In this paper, the deformation behavior of S32750 duplex stainless steel during low cycle fatigue was studied by controlling number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). Microhardness of two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. Two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in two phases was obviously different. With the increase of cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and dislocation array to sub-grain structure, while the dislocation in austenite gradually develops from dipole array to ordered Taylor lattice network structure.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

The aim of this work is to study the phase transformations, microstructures and mechanical properties of the martensitic stainless steel (MSS) 410 deposits produced by laser powder-directed energy deposition (LP-DED) additive manufacturing. The LP-DED MSS 410 deposits underwent the post heat treatment in austenitizing at 980℃ for 3hrs and followed by different tempering treatment at the temperatures of 250, 600, and 750℃ for 5hrs, respectively. The analyses of phase transformations and microstructural evolutions of LP-DED MSS 410 were carried out using X-ray diffraction, SEM-EDS, and EBSD. Vickers hardness and tensile strength properties were also measured to analyze the effects of the different tempering heat treatments. It reveals that as-built MSS 410 has very fine lath martensite and high hardness of about 480HV1.0 and tensile strength of about 1280 MPa, but elongation was very lower than the post heat treated ones. Precipitations of chromium carbide (Cr23C6) were most commonly observed at the grain boundaries and the entire matrix at the tempering temperatures of 600℃ and 750℃. In general, the tensile strengths de-creased from 1381MPa to 688MPa as tempering temperatures increased up to 750℃ from 250℃. Additionally, as the tempering temperature increased, the chromium carbide and tempered mar-tensite structures became coarser.

The microstructure evolution of SCM435 cold heading steel at different cooling rates was investigated by means of scanning electron microscopy, TEM, XRD, and electron backscatter diffraction. The results show that the cooling rate has a significant effect on the microstructure of the experimental steel. With an acceleration of the cooling, the microstructure of the steel gradually changed from ferrite and pearlite to ferrite, pearlite, and granular bainite; finally, the pearlite disappeared, and the microstructure changed to acicular ferrite, bainite, and martensite. With an increase in the cooling rate, the morphology of the carbide underwent an evolution from sheet carbide to short-rod carbide, granular carbide, and ultimately thin-strip carbide. With the acceleration of cooling, the proportion of large-angle grain boundaries gradually decreased, and the area of small-angle grain boundaries gradually increased. When the cooling rate was 0.1℃/s, the proportion of large-angle grain boundaries was as high as 52.8%, and the dislocation density was only 1.91 × 1012 cm−2. When the cooling rate was 2.0℃/s, the proportion of large-angle grain boundaries was only 27.1%, and dislocation density increased to 5.38 × 1012 cm−2. With the increase in the cooling rate, the depth of the decarbonization layer and the thickness of the scale oxide gradually decreased, the proportion of FeO phase in the scale phase gradually decreased, and the proportion of Fe3O4 phase and Fe2O3 phase gradually increased. The tensile strength increased monotonously with the increase in cooling rate, whereas the elongation and shrinkage first decreased, then increased, and then decreased. When the cooling rate was 1.0 m/s, the short rod and granular bainite in the material structure endowed the SCM435 steel with excellent strength and toughness matching, and the tensile strength and elongation of the steel reached 895 MPa and 24%, respectively.

The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

Abstract: The paper compares and analyses the effects of correctly and excessively executed heating cycles on flame straightening, far above the limits recommended by the steel manufacturer. The paperwork emphasizes the microstructural changes induced by overheating in the flame straightening process. Flame straightening is a flame heating process of metal constructions in which very limited areas of the construction are heated to the straightening temperature with the aim of inducing geometrical changes.The flame straightening process is used in most of metallic structure manufacturing companies. In many cases, it is not possible to carry out under economic conditions of metal structures without flame straightening.

TiC–high Mn steel-bonded carbide with a cellular structure was designed and fabricated by powder metallurgy techniques using coarse and fine TiC particles as the hard phase. This preparation process was carefully investigated and optimized. The microstructure of the TiC steel-bonded carbide was observed using a scanning electron microscope. Results showed that there are two types of microstructures in the TiC steel-bonded carbide: the coarse-grained TiC and fine-grained TiC. The transverse rupture strength and impact toughness of the alloy reach maximum values 2231 MPa and 12.87 J/cm2, respectively when the starting weight ratio of MP-A (containing coarse TiC particles) to MP-B (containing fine TiC particles) is 60:40. Hence, this study serves as a feasible example of how to prepare a high-strength and high-toughness TiC–high Mn steel-bonded carbide.

This study characterizes the microstructure and its associated crystallographic features of bulk maraging steels fabricated by selective laser melting (SLM) combined with a powder bed technique. The fabricated sample exhibited characteristic melt pools in which the regions had locally melted and rapidly solidified. A major part of these melt pools corresponded with the ferrite (alpha) matrix, which exhibited a lath martensite structure with a high density of dislocations. A number of fine retained austenite (gamma) with a <001> orientation along the build direction was often localized around the melt pool boundaries. The orientation relationship of these fine gamma grains with respect to the adjacent alpha grains in the martensite structure was (111) gamma // (011) alpha and [-101] gamma // [-1-11] apha (Kurdjumov–Sachs orientation relationship). Using the obtained results, we inferred the microstructure development of maraging steels during the SLM process. The results depict that new and diverse high-strength materials can be used to develop industrial molds and dies.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

Metal 3D printing technology is a promising manufacturing method, especially in the case of complex shapes. The quality of the printed product is still a challenging issue for mechanical applications. The anisotropy of the microstructure, imperfections, and residual stress are some of the issues that diminish the mechanical properties of the printed sample. The simulation could be used to investigate some technical details, and this research has tried to computationally study the metal 3D printing of austenitic stainless steel to address austenite microstructure and local yield strength. Two computational codes were developed in Visual basics 2015 to simulate the local heating/cooling curve and subsequent austenite microstructure. A stochastic computational code was developed to simulate austenite grain morphology based on calculated thermal history. Then Hall-Pitch equation was used to estimate the yield strength of the printed sample. These codes were used to simulate the effect of temperature of the printer’s chamber on microstructure and subsequent yield strength. The austenite grain topology is more columnar at a lower temperature. The percentage of the equiaxed zone will be increased at a higher chamber’s temperature. Almost a fully equiaxed austenite microstructure will be achieved at 800 C chamber’s temperature, but the last printed layer, which is columnar and can be removed by cutting then. The estimated local austenite grain size and the local yield strength in the equiaxed regions are in the range of 15 to 30 μm and 270 to 330 MPa at 800 C temperature of printer’s chamber, respectively.

The study proposes laser shock peening without a coating of high strength ultrafine bainitic steel to mitigating the fatigue failures for automotive and structural engineering applications. Laser pulse density of 2500 pulses/cm2 (75% overlapping) was optimised based on the induced residual stresses for employing the wide range of characterisations. The roughness and topographic results showed that surface roughening was controlled by tuning the laser pulse density. The High-Resolution X-ray Diffraction analysis confirmed the lattice misorientation resulting peak shift and the trend towards martensite phase transformations. The electron microscopic micro/nanostructure analyses revealed the grain refinement features such as nano-twins, micro shear bands and shear cells. The work hardening depth and nanomechanical properties were significantly enhanced. A fully reversed (R= -1) high-cycle fatigue tests extended the lifespan by an average of fifteen times than the untreated. Also, it has potential to repair the structural components effectively.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

The study presents the effect of annealing process parameters on the microstructure, hardness and strain hardening coefficients i.e., the strength coefficient c and the strain hardening exponent n, of 42CrMo4 steel. Seven selected annealing time-temperature schemes are examined for superior steel formability in cold metal forming conditions. The c and n coefficients are first determined in experimental upsetting of annealed samples and then used in FEM simulations of the upsetting process. The results demonstrate that the strain hardening coefficients (c and n) depend on the employed annealing scheme. Compared to the as-received sample, the annealing process reduces the true stress and effectively decrease the hardness of 42CrMo4 steel, improves microstructural spheroidization and, consequently, facilitates deformability of this material. The annealing schemes relying on heating the material to 750 °C and its subsequent slow cooling lead to the highest decrease in hardness ranging from 162 to 168HV. Results obtained with the SEM-EDS, LOM and XRD methods lead to the conclusion that the employed heat treatment schemes cause the initial ferritic-pearlitic microstructure to develop granular and semi-lamellar precipitation of cementite enriched with Mo and Cr in the ferrite matrix. In addition, the annealing process affects the growth of α-Fe grains. The highest cold hardening rate, and thus formability, is obtained for the annealing scheme producing the lowest hardness. The results of FEM simulations are positively validated by experimental results. Obtained results are crucial for further numerical simulations and experimental research connected with developing new cold metal forming methods for producing parts made of 42CrMo4 steel.

Powder and SLM additively manufactured parts of X5CrNiCuNb17-4 maraging steel were systematically investigated by electron microscopy to understand the relationship between the properties of the powder grains and the microstructure of the printed parts. We prove that satellites, irregularities and superficial oxidation of powder particles can be transformed into an advantage through the formation of nanoscale (AlMnSiTiCr)-oxides in the matrix during the printing process. The nano-oxides showed extensive stability in terms of size, spherical morphology, chemical composition and crystallographic disorder upon in situ heating up to 950°C in the scanning transmission electron microscope. Their presence thus indicates a potential for oxide-dispersive strengthening of this steel, which may be beneficial for creep resistance at elevated temperatures. The nucleation of copper clusters and their evolution into nanoparticles as well as the precipitation of Ni and Cr particles upon in situ heating have as well been systematically documented.

Fungal infection of grape berries (Vitis vinifera) by Botrytis cinerea frequently coincides with harvest, impacting both the yield and quality of grape and wine products. A rapid and non-destructive method for identifying B. cinerea infection in grapes at an early stage prior to harvest is critical to manage loss. In this study, zeolitic imidazolate framework-8 (ZIF-8) crystal was applied as an absorbent material for volatile extraction from B. cinerea-infected and healthy grapes in a vineyard followed by thermal desorption gas chromatography-mass spectrometry. The performance of ZIF-8 to absorb and trap targeted volatiles was evaluated with a standard solution of compounds and with a whole bunch of grapes enclosed in a glass container to maintain standard sampling conditions. Results from sampling methods were then correlated to B. cinerea infection in grapes as measured and determined by Genus specific antigen quantification. Trace levels of targeted compounds reported as markers of grape B. cinerea infection were successfully detected with in-field sampling. Peak area counts for volatiles 3-octanone, 1-octen-3-one, 3-octanol, and 1-octen-3-ol extracted using ZIF-8 were significantly higher than values achieved using Tenax®-TA from field testing and demonstrated good correlation with B. cinerea infection severities determined by B. cinerea antigen detection.

A medium-Mn steel was processed by a route involving twin-roll strip casting, hot-rolling and quenching and partitioning with different quenching temperatures. The effects of quenching temperature on the microstructure and mechanical properties were studied. It was found primary martensite and retained austenite (RA) were obtained at the quenching temperature of 140–180 °C, while primary martensite, RA and secondary martensite were obtained when the quenching temperature was 220–300 °C. With increase in quenching temperature from 140 to 260 and to 300 °C, RA fraction first increased from 15.4% to 31.8% and then decreased to 16.6%. The sample at quenching temperature of 220 °C yielded the mechanical properties with yield strength of 992 MPa, tensile strength of 1159 MPa and total elongation of 20.4%. The superior mechanical properties were achieved by an optimum combination of high RA fraction (26.5 vol%), appropriate mechanical stability of RA and a small amount of secondary martensite.

With the aim to investigate the effect of parameter and quenching process on the joint of hot stamping steel by laser welding, the BR1500HS boron steel was welded by filling-wire laser welding with ER70-G welding wire under different parameters. The welded specimens were heated to 900℃ and held for 5min before water quenching. The universal material test machine, Optical micro-scope, Vickers hardness tester, scanning electron microscope and electron backscatter diffraction (EBSD) were used to characterize. The results showed that the macroscopic morphology of fusion zone (FZ) becomes from funnelform to hyperbolic curve shape when heat input increases and from hyperbolic curve shape to funnelform when wire-feed speed increases. The strength after quenching is more than 1557Mpa at heat input of 1040J/cm, wire feeding speed of 1.6m/min~1.8m/min and welding speed of 1.5m/min. EBSD test showed that the FZ and fine grain zone (FGZ) have more retained austenite (RA) than coarse grain zone (CGZ) before quenching and RA in FZ and heat affect zone (HAZ) decreased and distributed uniformed after quenching. The grain diameter in FZ distribute unevenly, with the maximum grain diameter larger than 40μm before quenching. After quenching, the grain diameter of FZ, HAZ and BM is more even and coarse grains in the FZ was refined. Before quenching, the microhardness of FZ and HAZ is of 450HV~500HV at different heat input and wire-feed speed and all region of joint keeps at 450HV~550HV after quenching. Most dimple and little river pattern in the joint fracture mor-phology before quenching indicates a well plasticity and most cleavage facet is observed after quenching due to the joint combine with martensite.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

Longitudinal cutting is a most common process in steel structure manufacturing, and the man-hours of the process provide an important basis for enterprises to generate production schedules.However, currently the man-hours in factories are mainly estimated by experts, and the accuracy of this method is relatively low.In this study,we propose a system that predicts man-hours with history data in the manufacturing process and that can be applied in practical structural steel fabrication.The system addresses the data inconsistency problem by one-hot encoding and data normalization techniques,Pearson correlation coefficient for feature selection,and the Random Forest Regression(RFR) for prediction.Compared with the other three Machine Learning(ML) algorithms, the Random Forest algorithm has the best performance.The results demonstrate that the proposed system outperforms the conventional approach and has better forecast accuracy, so that it is suitable for man-hours prediction.

In this investigation steel P355NH has been successfully cladded with Inconel 625 through the method of explosive welding. Explosively welded bimetal clad-plate was subjected to the two separated post weld heat treatment processes: stress relief annealing (at 620oC for 90 minutes) and normalizing (at 910oC for 30 minutes). In order to analyze the microstructure of the joint in the as-welded state and to investigate the influence of the post weld heat treatment on it, the light and scanning electron microscope observations and microhardness analysis have been performed. The examination of the diffusion zone microstructure has been performed by using the scanning transmission electron microscope. It was stated that obtained joint has characteristic wavy-shape geometry with the presence of the melted zones and severe deformed grains of both joined materials. Strain hardening of the materials in joint zone was established with microhardness analysis. In both of the heat treatments the changes in the grain structure have been observed. The normalizing heat treatment has the most significant impact on the microstructure of the joint as well as the concentration of the chemical elements in the joint zone. It was reported that due to normalizing the diffusion zone has been formed together with precipitates in the joint zone. The analysis of the diffusion zone images leads to the conclusion that the diffusion of alloying elements from Inconel 625 to steel P355NH takes place along the grain boundaries with additional formation of the voids in this area. The precipitates in Inconel 625 in the joint zone are two type of carbides – chromium-rich and molybdenum-rich. Scanning transmission electron microscope observation of the grain microstructure in the diffusion zone shows that this area consists of equiaxed grains (from the side of Inconel 625 alloy) and columnar grains (from the side of steel P355NH).

Cementitious materials exhibit excellent binding properties and micropore structures that support the stabilization of TiO2 nanoparticles within the matrix. Therefore, these materials are ideal for the development of functional construction products with TiO2 nanoparticles. This study investigated the degree of hydration, microstructure, and mechanical properties of cement-containing TiO2 nanoparticles. The experimental results demonstrated that TiO2 nanoparticles accelerated the hydration rate of cement, reducing the setting times. Moreover, TiO2 nanoparticles changed matrix microstructure, decreasing the porosity and improving early-age strength. Although TiO2 nanoparticles function as nucleation sites in the cement hydration reaction, the tendency of the particles to clump implies that proper dispersion should be ensured when mixing in large quantities. When developing new building materials incorporating TiO2 nanoparticles, considering the effect of TiO2 nanoparticles on the hydration reaction of cementitious materials is crucial.

This paper introduces an innovative approach that enables automated and precise prediction of the steel's chemical composition based on the desired Jominy curve. The microstructure, and in fact the presence of martensite, is decisive for the hardness of the steel, so the study considered the occurrence of this phase at particular distances from the quenched-end of the Jominy sample. Steels for quenching and tempering and case hardening were investigated. With representative collected dataset of hardness values from quenched-end of Jominy specimen, microstructure and chemical composition of steels, the complex regression model was made using supervised artificial neural networks. The balance between cost and required hardenability can be achieved through optimizing the chemical composition of steel. This model of designing steel with required hardenability can be of great benefit in the mechanical engineering and manufacturing industry. The model is verified experimentally.

In the field of quality control, the critical challenge of analyzing microdefects in steel filament holds significant importance. This is particularly vital as steel filaments serve as reinforced fibers in the use and applications within various component manufacturing industries. This paper addresses the crucial requirement of identifying and investigating microdefects on steel filaments. Eddy current signals are used for the identification of microdefects, and an in-depth investigation is conducted. The core objective is to establish the relationship between the depth of defects and the signals detected through the eddy current sensing principle. The threshold of eddy current instrument was set at 10%, corresponding to a created depth of 20 µm, to identify defective specimens. A total of 30 defective samples were analyzed, and the phase angles between the experimental and theoretical results were compared. The depths of defects ranged from 20 to 60 µm, with one sample having a depth exceeding 75 µm. The calculated threshold of 10.18% closely aligns with the set threshold of 10%, with a difference of only 1.77%. The resulting root mean square error (RMSE) was found to be 10.53 degrees, equivalent to 3.49 µm for the difference in depth and phase between measured results and estimated results. This underscores the methodology's accuracy and its applicability across diverse manufacturing industries.

It is important for researchers in material domain to reconstruct and visualize the microstructure of alloy, which helps discover morphologies and properties that can only be found in three dimensional and microscopic space. However, because of the limitation of state-of-the-art sensors, the internal microstructure of the material is not easy to obtain. In this paper, a novel automatic 3D reconstruction method is proposed using diffraction contrast tomography technology to capture the 3D microstructure of Al-La alloy. The pipeline of the proposed method starts from the imaging of Al-La alloy with the LabDCT technique from Carl Zeiss AG, which produces a sequence of 2D microstructure sections. Then, a segmentation algorithm based on superpixel and lifted multicut is proposed to extract the 2D microstructure in an image section. Finally, 2D segmentations are joined together to reconstruct and visulize the 3D microstructure. As a result, a novel morphology of Al-La alloy is recovered with both dendrite and lamellar morphologies. The proposed method has the advantage of the ability to losslessly recover the internal microstructure.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

By using the method of high-temperature solid-phase reaction, the new piezoceramic SrBi2Nb2-2xWxSnxO9 was obtained, in which partial substitution of niobium (Nb) atoms with Sn4+ and W6+ atoms in the compound SrBi2Nb2O9 took place in the octahedra of the perovskite layer (B-position). X-ray diffraction studies have shown that these compounds are single-phase SrBi2Nb2-2xWxSnxO9 (x = 0.1, 0.2) and two-phase SrBi2Nb2-2xWxSnxO9 (x = 0.3, 0.4), but they all had the structure of Aurivillius – Smolensky phases (ASPs) with similar parameters of orthorhombic elementary cells, corresponding to the spatial group A21am. The dependences on temperature of the relative permittivity ε/ε0 and the tangent of the loss angle tan d at different frequencies were measured.

Steel surface protection with hard coatings is essential in the metalworking industry, yet developing high-performance hard coatings still remains a challenge. Quaternary nitride coatings, particularly TiAlSiN, have been extensively studied, but commercial TiAlSiN coatings vary widely, and there is a lack of consistent data. This study presents findings on the development and evaluation of TiAlSiN and TiAlSiN/TiN thin films, with an 800 nm thick TiAlSiN top coating and a 100 nm thick TiN mid-coating. The films were deposited on C120 tool steel discs via reactive DC magnetron sputtering. Ti and TiAlSi 75–20–5 (at.%) disc-shaped targets (50.8 mm diameter × 6.3 mm thickness), fabricated by our team through spark plasma sintering, were used for the sputtering process. Coatings were grown on smooth steel substrates heated to 300 °C, resulting in a uniform micro-structure with nanoparticles of globular (TiN) or pyramidal shape (TiAlSiN), as evidenced by SEM analysis. Nanoindentation tests showed superior mechanical properties for all coatings compared to the steel substrate. Micro-scratch tests indicated better scratch resistance for TiAlSiN/TiN bilayer (BL) coatings than for TiAlSiN single-layer (SL) coatings. Electrochemical impedance spectroscopy tests in a 3.5 wt.% NaCl solution revealed that the BL coatings demonstrated superior corrosion resistance compared to the SL coatings, even after thermal aging at 800 °C for 1 hour. The superior properties of the synthesized TiAlSiN/TiN films recommend them as protective coatings for tool steel surfaces.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

Whey protein was pretreated with multi-frequency ultrasound in mono, dual, and tri-frequency modes. The effect of multi-frequency ultrasound pretreatment on the hardness, chemical forces, and microstructure of acid-induced whey protein gel was investigated. Whey protein gels pretreated with dual and tri-frequency ultrasound showed higher hardness (p3.35 mm) in those samples were resisted to gastric digestion. Moreover, the tri-frequency ultrasound pretreatment of whey protein gel released the least free amino group during gastric digestion. In contrast, whey protein gel with the mono-frequency ultrasound pretreatment released the highest amount of free amino acid group during intestinal digestion. Findings from this study suggested that gel hardness and network density could modulate the digestion behaviors of protein gels.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

The laser melting process (DED-LB-p) is used for the production of large components due to the high deposition rates. The large number of process parameters and printing strategies makes it difficult to optimize this process to achieve the optimal properties. Intensive post-processing is still the main obstacle to the widespread use of this process. In this work, the relationship between different printing strategies, printing strategies and process parameters on the microstructural, and tensile mechanical performance at room temperature is investigated. The porosity was measured in both printing directions. Grain orientation and size were analyzed by EBSD. A very low porosity of less than 0.4% was found in all printed samples. The samples printed with the optimized offset printing strategy show a significant improvement in tensile strength of 1000 MPa without heat treatment compared to other processing routes.

The awareness of the vulnerability of existing structures under both seismic and energy viewpoints highlight the need to develop integrated retrofit solutions combining the structural and thermal performances. In this perspective, the study explores the efficacy of the Resisto 5.9 Tube system, a seismic coat that improves the seismic behaviour of masonry and reinforced concrete (RC) structures, also enhancing their energy performances, thanks to the thermal coat integrated in the basic steel system. The research involves the application of a design procedure specifically developed for this retrofit system from the seismic perspective. Once all the system elements are designed, non-linear static analyses are performed with a Finite Element software comparing the building’s seismic performances before and after the application of Resisto 5.9 Tube. The results demonstrate a significant increase in seismic safety coefficient, proving that this intervention type can be useful to obtain the seismic upgrading of existing RC buildings.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

The state of Oaxaca, Mexico obtained the “Pluma” designation of origin in 2022 and has stood out for the production of specialty coffee. Within its process, roasting is one of the stages that contributes to the physical, chemical and sensory quality of the coffee bean. Therefore, the microstructure and elemental chemical composition of special medium-roasted Coffea arabica L beans from six locations with this denomination were analyzed using Scanning Electron Microscopy. The average values of roughness Rz (25.93±2.69-34.18±1.15 and 13.85±1.66-21.85±6.63) and Ra (5.20±0.47- 8.27±0.82 and 6.55±0.94-11.53±1.65) were obtained at 400 and 2000x, respectively. The roasted Coffea arabica L. beans from MAP and HUA are the ones with the greatest roughness and both are located at a lower altitude compared to the rest. PLU and PTO roasted beans showed the highest physical and structural integrity. In all grains, 6C (66.48-81.14%), 8O (18.86-28.69%) and only 20Ca (4.5%) were found on the outside. This research constitutes a standard of authenticity and microstructural and elemental quality of Coffea arabica L. beans with designation of origin "Pluma".

In the decarbonization of the steel, cement, and chemical industry in Germany, green hydrogen is expected to play a crucial role. The utilization of green hydrogen in the production processes of said industries requires organizations to modify their business model, requiring sustainable business model innovation (SBMI). Numerous tools and frameworks that support organizations in the process of SBMI have been proposed in the literature in recent years. However, the applicability of these tools and frameworks for steel, cement, and chemical companies that intend to utilize green hydrogen to produce their goods remains unexplored. By conducting a systematic literature review on tools and frameworks for SBMI, a literature and practice review to identify and analyze existing green hydrogen projects of steel, cement, and chemical companies, and an evaluation of the identified tools and frameworks in an evaluation matrix, this paper aims to assess the suitability of SBMI tools and frameworks for steel, cement, and chemical companies that plan to use green hydrogen to produce their goods. Based on the evaluation, the Cambridge Business Model Innovation Process (CBMIP) was identified as the most suitable SBMI framework.

The paper presents the problem of damage detection in steel girders. Static displacements at the selected point of the structure play the role of measured variables. Structural response signal decomposition is performed according to the Mallat pyramid algorithm, which is used to perform the discrete wavelet transform (DWT). This procedure allows us to quite well determine the location of structural damage. The geometry and the placement of any defective part of the structure may have a random character. It can be assumed that the random processes occurring in the broadly understood structure mechanics are Gaussian in nature. The first four probabilistic moments are estimated using three approaches independent: semi-analytical (SAM), perturbative (SPT), and Monte-Carlo simulations (MCS). The semi-analytical random approach seems to be the most optimal due to the necessary computation time. The incorporation of the mathematical stochastic apparatus into the classical (deterministic) analysis of the statics of the structure makes it possible to estimate the reliability measures of the analyzed girder.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (&gt;0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

Although various atmospheric corrosion simulation models have been developed that give good results, industrial environments are still challenging. This paper aims to investigate the effect industrial atmospheres in Bor on the mechanical properties of structural steel S235JR and to create a constitutive model and also laboratory experimental conditions that will give the best results as an accelerated corrosion test. Atmospheric corrosion tests lasted six months, using sites close to the Electrolytic Refining Plant and Sulphuric Acid Plant, as well as air quality monitoring stations at a remote location in the city of Bor. The laboratory experiments included a salt chamber test lasting 120 h and 240 h and immersing the specimen in the electrolyte from the Electrolytic Refining Plant for 30 days. The results were compared with the standard specimens stored in the laboratory. The X-ray diffraction (XRD) method was used to identify the composition of corrosion products. The scanning electron microscopy (SEM) analysis was applied to analyze the fracture surfaces of the specimens. The use of the Complete Gurson Model (CGM) described the tensile characteristics of the corroded specimens. The study has shown that an enhanced acceleration model and conditions could be developed using numerical analysis of the test results.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

Lap joints were friction stir welded in AA 7075-T6 at 1320 rpm and using two welding speeds: 70 mm/min and 120 mm/min. The temperature profiles of the weld zone were registered during the process; furthermore, the microhardness, tensile strength, and microstructure of the joints produced were examined. This study brings new insights into the thermomechanical behavior of the material during the process. The peak temperature obtained with the lower welding speed (70 mm/min) is 10% higher than that obtained with the higher speed (120 mm/min). Moreover, a 5% increase in microhardness and a 6% increase in tensile strength were were observed increasing the welding speed. Addition-ally, the microstructure examination demonstrated that, by decreasing the welding speed, the larger interaction between the tool and the material results in a deeper stir zone due to the increased heat diffusion downwards to the material. This heat flow affects the thermal profile and influences the resulting mechanical properties of the welded joints.

Abstract: Molybdenum (Mo) thin films were sputtered from two kinds of Mo targets with different microstructures under the same sputtering process, and the effect of microstructure of Mo target on morphology, deposition rate and resistance of sputtered film were studied and discussed. The results show that morphological differences between Mo thin films sputtered by Mo targets with different microstructures are very small. The more uniform and finer the grain structures of Mo target, the better the uniformity on thickness and resistance of Mo sputtered film. Moreover, during sputtering process, when Mo target’s grain size is finer and the surface area of grain boundary is higher, the thickness reduction of the target is more homogeneous and the sputtering film has faster deposition velocity. The difference in microstructure of the Mo target has not obvious influence on the grain orientation of sputtering film.

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO2 thin films were elucidated using real-time synchrotron radiation imaging, its structure determined using grazing incidence X-ray diffraction (GIXRD), its morphology imaged using the field emission scanning electron microscopy (FESEM), and its surface topography examined using the atomic force microscope (AFM) in contact mode. Cubical white spots were detected, identified as Ag, while the TiO₂ thin film resembles a porous ring-like structure with each ring coalescing and forming channels. Junction growth is directly proportional with time under continuous heating conditions (annealing), and its growth orientations and patterns were seemingly random.

This study investigates the fatigue behavior of cold-finished mild steel subjected to electrochemical hydrogen charging under controlled conditions. Samples were hydrogenated at constant time in a fixed electrolyte pH after which they underwent fatigue testing under constant loading condition with fixed frequency. The primary objective was to assess the impact of varying hydrogen permeation levels on the number of cycles to failure. The experimental results revealed a complex relationship between hydrogen concentration and fatigue life. Initially, as hydrogen permeation increased, the number of cycles to failure substantially decreased, demonstrating a detrimental effect of diffused hydrogen on fatigue resistance of samples. This decline in fatigue life was attributed to hydrogen embrittlement (HE) and hydrogen-enhanced decohesion (HEDE) phenomena, which collectively facilitate crack initiation and propagation. However, at high hydrogen concentrations, an unexpected increase in number of cycles to failure was observed suggesting the existence of a threshold hydrogen concentration beyond which the fatigue mechanisms may be altered, potentially due to saturation of hydrogen-related defects and mechanisms such as Hydrogen Enhance Localized Plasticity (HELP). The insights gained from this research have significant implications for the material's application in hydrogen-rich environments, such as those encountered in the energy and transportation industries.

This paper presents an advanced microstructural analysis of the AlSiMg, Ti64 and N700 powders used for additive manufacturing. The internal microstructure of the regular and irregular powder grains were characterized down to atomic resolution by using scanning electron microscopy and high resolution scanning transmission electron microscopy.The accretionary forms on top of the irregular AlSiMg powder grains exhibit a slightly coarse microstructure with a network of eutectic Si consisting of nano-crystallites, suggestinga slower cooling than the grain itself that contain a predominately amorphous Si network. A nm thin amorphous C layer on the surface of some Ti64 plasma atomized powder grains promoted the attachment of satellites and growth of envelopes. In case of gas atomized N700 powder grains, we identified thin oxide and carbon amorphous layers as well as metal segregations at the interface between the grain body and the accretionary forms.

The production of a ton of steel in an integrated steel plant generates of approximately 1 ton of ferrous slag. A great part of ferrous slags is recycled in civil and road construction etc., but a huge amount is still dumped. Recycling ferrous slag as cement precursor was considered the upcycling route. Regulation (EU) 2024/1252 requires the Member States to provide information, until November 2026, on the critical raw materials (CRM) amount in their secondary resources and on quantification methods used for. This study addresses two synergic objectives: ensuring the reliability of XRFS results and screening for CRM in ferrous slags based on XRFS outcomes. The main novelty of the paper is the way of ensuring the reliability of the XRFS results based on weighted arithmetic mean and on the maximum likelihood approach. Secondly, the XRFS measurements carried on ferrous slags demonstrate that they contain significant amounts of CRM like Ba, Sr, Y, etc. XRFS cannot detect light CRM. Our preliminary LIBS measurements on ferrous slags disclosed the presence of Li and Be. The drawbacks of the XRFS technique impose further research to develop an integrated XRFS, LIBS and XRD procedure for comprehensive and trustworthy CRM screening in extractive waste piles.

The microstructure evolution during the cold rolling and subsequent annealing of Alloy 800H was investigated. Two distinct rolling methods, unidirectional rolling and cross-rolling, were intro-duced. Results show that better ductility was observed in the unidirectional rolling than in cross-rolling, whilst a higher volume fraction of large deformed grains was observed in the cross-rolled plates than in the unidirectionally rolled plates. Recrystallization occurred faster in plates from unidirectional rolling than from cross-rolling.

Struts of a superconducting YBa2Cu3Oy (YBCO) foam prepared by the infiltration growth method on the base of commercial polyurethane foams were extracted from the bulk, and thoroughly characterized concerning the microstructure and the magnetoresistance, measured by the four-point technique. Optical microscopy, electron microscopy, electron backscatter diffraction and atomic force microscopy observations indicate an unique microstructure of the foam struts which shows a large amount of tiny Y2BaCuO5 (Y-211) particles (with diameters between 50–100 nm) being enclosed in channel-like grain boundaries between the YBCO grains and an one-of-a-kind surface of the struts covered with Ba3Cu5Oy-particles. The resistance data obtained at temperatures in the range 4.2 K ≤T≤ 150 K (applied magnetic fields ranging from 0 to 7 T) were analyzed in the framework of the fluctuation-induced conductivity (FIC) approach using the Aslamazov-Larkin model. The resulting FIC curves reveal the presence of five distinct fluctuation regimes, namely, the short-wave (SWF), one-dimensional (1D), two-dimensional (2D), three-dimensional (3D), and critical (CR) fluctuation domains. The analysis of the FIC data enable the coherence length in the direction of the c-axis at zero-temperature (ξc(0)), the lower and upper critical magnetic fields (Bc1, Bc2), the critical current density at T= 0 K (Jc(0)) and several other parameters describing the the material’s superconducting properties to be determined. The present data reveal that the minuscule Y-211 particles found along the YBCO grain boundaries alter the excess conductivity and the fluctuation behavior as compared to conventional YBCO samples, leading to a quite high value for Jc(0) for a sample without added flux pinning centers.

CO₂ emissions have been identified as the main driver for climate change, with devastating consequences for the global natural environment. The steel industry is responsible for ca. 8%-11% of global CO₂ emissions, due to high fossil-fuel and energy consumption. The onus is therefore on industry to remedy the environmental damage caused and to decarbonise production. This desk research report follows a two-tiered route: 1) exploring the Bio Steel Cycle; 2) proposing a seven-step strategy to overcome the challenges within the iron and steel industry. The true levels of CO₂ emissions in the steelmaking process, during the blast-furnace/basic-oxygen-furnace operation, will be detailed first, at 4.61t of CO₂ emissions/t of steel produced. The manuscript proposes a solution for reduced carbon emissions steelmaking with the Bio Steel Cycle components and detail on how to reach net-zero carbon emissions steel production. The 7-step-implementation-strategy as a potential solution to achieve net and true zero carbon emissions steel production in the short to medium-term. The findings of this are pointing towards the conclusion that CO₂ emissions seem to have been under-reported and under-estimated in the past, but the emission can be addressed if the correct scenarios for net-zero steel manufacturing are implemented by 2050.

Considerable amounts of agro-industrial by-products are discarded or burnt as fuel every year. However, they can be utilized as a valuable source of fiber, phenolics and other useful compounds such as antioxidants. The profile of beneficial compounds can be affected by genotype, locality, orchard management and productive season, adding or decreasing the bioactive potential of by-products. In this study, hazelnut (Corylus avellana L.) and walnut (Juglans regia L.) nutshells were investigated for their fiber content and antioxidant capacity as valorized by-products for the industry. Determinations (ORAC, TPC and color asses) were performed in hazelnut and walnut orchards located in Southern Chile during three consecutive seasons (2020/21; 2021/22 and 2022/23). Analyses of oxygen radical absorbance capacity (ORAC) in nutshells showed the highest ORAC from both species in the season 2020/21 (3217 µmol TE g1DW for hazelnut shells and 4663 µmol TE g DW1 for walnut shells), while variability in the consecutive seasons was lower for hazelnut than in walnut. Total phenolic content in hazelnut shells was positively correlated with L* (R: 0.883) and E (R: 0.924) during 2020/21 season, also with L* for 2022/23 (R: 0.907). While ORAC was negatively correlated with L* (R: 0.922) in 2021/22. In addition, morphological and structural features of both nutshells examined by Scavenging Electron Microscopy (VP-SEM) and Confocal Scavenging Laser Microscopy (CSLM) revealed differential tissue distribution and accumulation patterns of both cellulose and lignin. On the other hand, photo-colorimetric values were determined for both shells and corresponding seasons, and non-significative differences were found both shells and among seasons Finally, these results provide insight into the physicochemical characteristics of two shell types which should be considered together with antioxidant capacity in their valorization as a residual material.

Steel fibre reinforced concrete (SFRC) consists of short hooked steel fibres randomly distributed and oriented within the cementitious matrix. The contribution of fibre in bridging cracks to provide the stress transfer required relies upon the orientation of the fibre in the concrete. Bridging fibre aligned with a crack are less effective than those inclined to it. Therefore, understanding the pull-out behaviour of misaligned fibre is a key factor to quantify and optimize the design of SFRC in the structural applications. In the laboratory a single oriented fibre embedded in a solid cylinder of concrete is subjected to a pull-out test where the axis of a tensile force is aligned with the axis of the cylinder. Based upon the observed behaviour this paper presents a new analytical bounding approach to capture the pull-out response of misaligned hooked-end steel fibre embedded in a concrete matrix. The analysis is based upon a transversely isotropic condition assumed for the plasticity that occurs in the cold drawn fibre. The model accounts for the influence of fibre diameter and the combined strengths of the steel and concrete. The model predictions have also been compared with other experimental results published in the literature. The results showed that the model can predict pull-out loads reasonably for different fibre orientations between bounds of failure derived from the strengths of the two constituents. A critical orientation is observed at maximum strength. Therein, an understanding of the pull-out behaviour of misaligned, hooked-end fibres is necessary to optimize the strength of concrete from this method of reinforcement.

The effectiveness of a hybrid technique for identifying seismic damage in planar, multistory, steel X or V-braced frames is demonstrated here through an example of a six-story frame. This proposed technique, referred to as “M and P”, combines the instrumental Monitoring (M) with Pushover analysis (P). According to the methodology, the diagram of stepping eigenfrequencies of the frame in the inelastic region is initially plotted against seismic roof displacement. The fundamental natural frequency detected via the monitoring process is then utilized in this key diagram to reveal the inelastic roof displacement that corresponds to the damage state of the steel braced frame. This displacement is subsequently used as the target in the pushover analysis, facilitating the identification of seismic damage in the existing steel braced frame. Finally, the damage image is correlated with the damage stiffness matrix of the frame at the same inelastic roof displacement. The investigation results indicate that combining instrumental monitoring with pushover analysis enables accurate identification of seismic damage potential in existing steel braced frames.

The tribological performance of metalwork steel tools is of vital importance in both cold and hot working processes. One solution for improving metal tool life is the application of coatings. This paper investigates the effect of CrAlSiN thin-film PVD-deposition on the tribological behaviour of tool steel K340. The sliding wear performance of the coated K340 steel is analysed in relation to both the uncoated K340 steel and a range of tool steels dedicated to hot- and cold-working, such as X155CrVMo12-1, X37CrMoV5-1, X40CrMoV5-1, 40CrMnMo7 and 90MnCrV8. The investigated tool steels were heat-treated, while K340 was subjected to thermochemical treatment and then coated with a CrAlSiN hard film (K340/CrAlSiN). The hardness, chemical composition, phase structure and microstructure of steels K340 and K340/CrAlSiN are examined. Tribological tests were conducted using the ball-on-disc tester in compliance with the ASTM G99 standard. The tests were performed under dry unidirectional sliding conditions, using an Al2O3 ball as a counterbody. The wear factor and coefficient of friction are estimated and analysed with respect to hardness and alloying composition of the materials under study. SEM observations are made to identify the sliding wear mechanisms of the analysed tool steels and PVD-coated K340 steel. In contrast to the harsh abrasive-adhesive wear mechanism observed for uncoated tool steels, the abrasive wear dominates in case of the AlCrSiN. The deposited thin film effectively prevents the K304 substrate from harsh wear severe degradation. Moreover, thanks to the deposited coating, the K304/CrAlSiN sample has a COF of 0.529 and a wear factor of K=5.68×10−7 m3 N−1 m−1, while the COF of the reference tool steels ranges from 0.702 to 0.885 and their wear factor ranges from 1.68×10−5 m3 N−1 m−1 to 3.67×10−5 m3 N−1 m−1. The CrAlSiN deposition reduces the wear of the K340 steel and improves its sliding properties, which makes it a promising method for prolonging the service life of metalwork tools.

The CuCrSn alloy is promising as high-strength and high-conductivity Cu alloy due to its relative low smelting requirement, while thus far reports on the CuCrSn alloy is still quite lacked. In this study, the microstructure and properties of Cu-0.20Cr-0.25Sn (wt%) specimens prepared under different rolling and aging combinations were comprehensively characterized, in order to reveal the effects of cold rolling and aging on the CuCrSn alloy. The results show that increasing the aging temperature from 400 ºC to 450 ºC can obviously accelerates the precipitation, and the cold rolling before aging significantly increases the initial microhardness and promotes the precipitation. Whereas, the deformation hardening will be eliminated during the aging process, making the microhardness even decrease monotonically when the aging temperature and the rolling ratio before aging are high. Performing the cold rolling after the aging can maximize the effects of precipitation strengthening and deformation strengthening, and its adverse impact on the conductivity is not serious. A tensile strength of 506.5 MPa and a conductivity of 70.33% IACS were obtained with such a treatment, only the elongation decreases. Different strength-conductivity combinations of the CuCrSn alloy can be achieved through appropriate combinations of the aging and post aging cold rolling conditions.

The influence of aluminosilicate pozzolanic waste, specifically spent fluid catalytic cracking catalyst (FCCW) and metakaolin waste (MK) from expanded glass industry, on the properties of hardened Portland cement paste were analysed. The study involved replacing part of cement with FCCW and MK and observing their impact on hydration, microstructure, density and compressive strength of hardened cement paste. Various analysis methods were employed, including X-ray diffraction (XRD), thermogravimetric analysis (TG), and scanning electron microscopy (SEM), to understand the changes in the structure of hardened cement paste during hydration. The findings revealed that FCCW tends to accelerate cement hydration process due to its high surface area and pozzolanic activity. Notably, the formation of portlandite crystals was observed on FCCW particle surfaces in a specific direction. These crystals appeared smaller and developed in different directions in compositions containing a composite binder with mixture of FCCW and MK in a ratio 1:1. This could be influenced by pozzolanic reactions activated by fine particles of MK and the formation of calcium silicate hydrates (CSH) and calcium alumino silicate hydrates (CASH) in the presence of portlandite. XRD and TG results indicated that the specimens containing a composite binder exhibited the least amount of portlandite. The compressive strength of these specimens increased compared to control specimens, although the amount of cement was 9% lower.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

The paper presents the results of the study of tungsten surface structure modification under helium plasma irradiation. It is revealed that during irradiation of samples, surface modification in the form of relief development as a result of irradiation is observed. X-ray phase analysis showed that no new phases of the W system were found after irradiation, only an increase in the intensity of diffraction lines was observed. There are significant differences in the microstructure of tungsten depending on the temperature of helium plasma irradiation in the above range. It is assumed that the cause of defects is the extremely low solubility of helium in tungsten. Metallographic analysis has shown that at irradiation of tungsten samples in regime 5 and 6 the degree of relief development is not high in comparison with the tungsten sample irradiated in regime 4. The greatest increase in roughness of the sample irradiated in regime 5 was determined, which is associated with the formation of small cracks, blisters and pores in the surface layer. At the same time, in the samples irradiated in regime 6, the surface of which is characterized by chaotically located protrusions and depressions of various shapes, the roughness parameter Ra was 0.0603 µm. It was found that at temperature regimes T = 1200 °C and T = 1500 °C the microhardness of tungsten increases by 11% and 10% respectively.

The study of co-fusion was one of the essential topics in the history of metallurgy in China. Simulation experiments had been an essential concept in the study of the co-fusion steelmaking process. This paper mainly studied the simulation experiments of co-fusion from two aspects: the replication of co-fusion swords by three different methods, and the micro-analysis of the co-fusion samples. The experimental results indicated that several co-fusion swords could be made by different processes, but the carbon content and surface hardness were quite different. During repeated forging welded, the microstructure of the samples transformed from laminated to homogenized, finally the steel with a uniform carbon content was obtained. It was challenging to find the characteristics of co-fusion from the homogenized samples. The results prompted people to rethink the microstructure characteristics of ancient co-fusion artifacts.

In typical Cobalt-chromium (CoCr) alloys powders, aluminum oxide (Al₂O₃) powder can be added. In the present study, we successfully prepared alloyed samples of various powder ratios by laser cladding, and analyzed their microstructure and carbide structural characteristics, including microhardness, biological properties, morphology (using scanning electron microscopy), and crystal structure (using X-ray powder diffraction). Elemental distribution was also determined by energy-dispersive X-ray spectral analysis. The results showed that Al₂O₃ addition caused the alloy to change from slender columnar crystals to columnar grains similar, to equiaxed grains. In addition, Al₂O₃ agglomeration zones appeared, and carbide structures were altered. The mechanism of the observed performance changes was also analyzed.

In this paper, polyurethane concrete (PUC) is used as wire embedding material to form a new polyurethane concrete- prestressed steel wire (PUC-PSW) reinforcement method. The lightweight and high-strength PUC materials not only bond and anchor the prestressed steel wire (PSW), but also passively participate in the structural force. The problems caused by using mortar or composite mortar as the embedding material are avoided. Twelve reinforced concrete T-beams were tested for PUC-PSW flexural reinforcement. It consists of 1 unreinforced beam, 4 PSW reinforced beams, and 7 PUC-PSW reinforced beams. The wire embedding material, wire anchorage form, PUC material depth, amount of wire, and loading type were used as variables. The test results show that PUC-PSW reinforcement can obviously enhance the flexural load and ultimate load of the reinforced beams compared with PSW reinforcement. The ability of PUC-PSW reinforcement to limit crack development is better than that of PSW reinforcement beam, especially after the main beam steel yield. The strength, stiffness and crack limiting ability of the reinforced beam increase with the PUC thickness of the reinforced layer.

The soil organic matter (SOM) content and stability in natural gypsum soils and soils from mining/industrial areas were compared, in terms of their physical, chemical and micromorphological properties, to determine whether the old brownfield soils were acting as carbon (C) sinks, counteracting increasing carbon dioxide concentrations in the atmosphere. The mining/industrial soils were 50–400 years old, so had been left sufficiently long for full self-restoration. Despite having very different origins, both natural and brownfield soils stored similar amounts of SOM, and had similar pH values, calcium carbonate contents and textures. They were also fully covered with similar grass plant communities. The mining/industrial soils exhibited similar microstructures to the gypsum soils and were often quite porous. The most striking difference between them and the natural gypsum soils was that the mining/industrial soils were strongly polluted with zinc, lead and cadmium. The 50-year-old brownfield soils differed from the others in terms of having a lower state of SOM transformation, with a much higher C/N ratio, lower aggregate water resistance index, lower dehydrogenase activity and greater areas of undecomposed or slightly decomposed plant residues. These parameters in the older (150–400 years) brownfield soils were similar to those of the natural soils.

K417G Ni-based superalloy is widely used in aeroengine turbine blade for its excellent properties. However, the aeroengine rotor blade zigzag crown appears early failure frequently, which is because of the wear problems occurring in the working process. Laser forming repairing (LFR) is a promising technique to repair these damaged blades. Unfortunately, the laser formed Ni-based superalloys with high content of (Al + Ti) have a high cracking sensitivity. In this paper, the crack characterization of the LFRed K417G, the microstructure, microhardness and tribological properties of the coating before and after laser remelting are presented. The results show that the microstructure of as-deposited K417G consists of γ phase, γ′ precipitated phase, γ + γ′ eutectic and carbide. Cracking mechanisms including solidification cracking, liquation cracking and ductility dip cracking are proposed based on the composition of K417G and processing characteristics to explain the cracking behavior of the K417G superalloy during LFR. After laser remelting, the microstructure of the coating has been refined, and the microhardness and tribological properties has been improved. Laser remelting can decrease the size of the cracks in the LFRed K417G but not the number. Therefore, laser remelting can be applied as an effective method for strengthening coating and as an auxiliary method for controlling cracking.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

In this work, cobalt doped ZnO nanorod arrays with anticorrosion function were successfully prepared on FTO substrate by a simple aqueous solution method. XRD and EDS results indicate the doped Co2+ has successfully incorporated into the ZnO crystal lattice. Photocurrent density and open circuit potential (OCP) results indicate the photocathodic protection performance for 316 stainless steel (316 SS) and Q235 carbon steel in 3.5 wt.% NaCl solution under 300 W Xe lamp enhanced with the increase of cobalt concentration, and the photoanode with 15% Co/Zn ratio has the optimal photocathodic protection effect. The mechanism of enhancement may be result from the narrowed band gap, the lower recombination rate of photogenerated electron-holes, the intermediate impurity level and the split of the hypo-outer shell of cobalt ions.

In this work, we have studied microstructure and unusual ferromagnetic behavior in cobalt (Co)-implanted epitaxial tin dioxide (SnO2) films. The study was aimed to provide a comprehensive understanding of the interplay between cobalt implant distribution, crystal defects, such as oxygen vacancies, and magnetic properties in Co-implanted SnO2 films, which has potential applications in spintronics and memristor devices. The scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometry (VSM), differential thermo-magnetic analysis (DTMA), and ferromagnetic resonance (FMR) were employed for investigations of SnO2 films implanted with 40 keV Co+ ions at room or the elevated temperatures of substrate. The experimental data showed that the Co ion implantation with high fluence of 1.0 1017 ions/cm2 induces significant changes in the microstructure of SnO2 films, leading to the appearance of ferromagnetism with the Curie temperature significantly above room temperature. Strong influence of implantation temperature and subsequent high-temperature annealing in air or in vacuum on magnetic properties of Co-implanted SnO2 films were established. Moreover, the chemical effect of ethanol on FMR spectra were observed. The obtained results are discussed within the model of two magnetic layers with different concentration and valence states of the implanted cobalt and with high content of oxygen vacancies.

The effect of defects and microstructure on mechanical properties of Ti-6Al-4V welds produced by tungsten inert gas welding, plasma arc welding, electron beam welding and laser beam welding was studied in the present work. The mechanical properties of the different weld types have been evaluated with respect to micro hardness, yield strength, ultimate tensile strength, ductility and fatigue at room temperature and at elevated temperature. Metallographic investigation was carried out to characterize the microstructures of different weld types and fractographic investigation to relate the effect of defects on fatigue performance. Electron and laser beam welding produced welds with finer microstructure, higher tensile ductility and better fatigue performance than tungsten inert gas welding and plasma arc welding. Large pores and pores located close to the specimen surface were found to be most detrimental to fatigue life.

In recent years, there has been growing interest in thermal spray techniques using suspension or solution-based coatings. These techniques offer precise control over particle size and microstructure, improving feedstock flowability and allowing for high-quality coatings customization. Spray parameters, such as stand-off distance (SOD) and feedstock flow rate, can alter the performance and characteristics of these coatings. Geothermal power plant heat exchangers often face issues like corrosion, scaling, and fouling. These issues could be mitigated, at least in part, by the use of spray coatings. In this study, TiO2 coatings were applied to a carbon steel substrate using suspension plasma spray (SPS) to enhance the performance of geothermal heat exchanger materials. The impact of SOD (50, 75, and 100mm) and feedstock flow rate (10, 20, and 30 ml/min) on these coatings was examined through various techniques, including SEM, profilometry, XRD, and adhesion testing. The results demonstrated that coatings deposited using 10ml/min feedstock flow rate were well-adhered to the substrate due to efficient melting of coating material but as the SOD and feedstock flow rate increase due to poor thermal and kinetic energy exchange between the torch and feedstock particles, adhesion between coating and substrate decreases. smaller SODs led to more compact coatings, while higher feedstock flow rates increased coating porosity. Smaller SODs and lower flow rates resulted in well-adhered coatings, offering valuable insights for advancing geothermal heat exchanger coatings.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Equiatomic CuZr alloy undergoes a martensitic transformation from the B2 parent phase to martensitic phases (P21/m and Cm) below 150 °C. We clarified the effect of the thermal cycling on the morphology and crystallography of martensite in equiatomic CuZr alloy using a transmission electron microscopy. The 10th cycled specimens consisted of different multiple structures at the maximum temperature of DSC measurement: 400 °C and 500°C, respectively. At the maximum temperature 400 °C of DSC measurement, it is composed of the fine plate-like variants, and a lamellar eutectoid structure consisting of Cu10Zr7 and CuZr2 phases on the martensitic variant. Concerning the maximum temperature 500 °C of DSC measurement, it is observed the martensitic structure and the lamellar structure in which the martensitic phase was completely eutectoid transformed. The formation of this lamellar eutectoid structure due to thermal cycling leads to the shift of forward and reverse transformation peaks to low and high temperature side. In addition, new forward and reverse transformation peaks indicating a new transformation appeared by thermal cycling, and the peaks remained around -20 °C. This new martensitic transformation behavior is also discussed.

The microstructure of Al-5Fe-1.5Er alloy was characterized and analyzed by using XRD, SEM, TEM and EDS. The effect of microstructure on the behavior of crack initiation and propagation was investigated by in situ tensile testing. Results show that the microstructure consists of α-Al matrix, Al₃Fe, Al₄Er, eutectic phase Al₃Fe + Al₄Er, while the 1.5 wt.% Er was added in Al-5Fe alloy. The twin structure of the Al₃Fe phase was observed, and the twin plane is {001}. Moreover, a continuous concave and convex interface structure of the Al₄Er has been found. Al₃Fe is in the form of a sheet with a clear gap inside.In situ tensile tests of the alloy at room temperature show that the crack initiation occured mainly in the Al₃Fe phase, and that the crack propagation modes include intergranular and transgranular expansion. Crack transgranular expansion is due to the strong binding ability between Al₄Er phases and surrounding organization, and the continuous concave and convex interface structure of the Al₄Er provides a significant meshing effect on the matrix and eutectic structure.

The corrosion inhibition behavior of cetyl pyridinium chloride (CPC) on mild steel (MS) in 0.5 M H₂SO₄ solution was examined using the weight loss method and potentiodynamic polarization method. The experimented MS surface was characterized by Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Atomic Force Microscopy (AFM). Corrosion rate and corrosion efficiency was calsulated via weight loss and potentiodynamic polarization methods where the corrosion rate in 0.5 M H₂SO₄ , 0.000192 M, and 0.0077 M of CPC solution was 12.09×10^-3, 8.23×10^-3, 6.63×10^-5 (mm/Year), respectively and the inhibition efficiency of 94.42% and 98.54%. FESEM studies demonstrated the corrosion attack on MS surface. Also, the EDX showed the presence of nitrogen of CPC. Thus, CPC acts as an important corrosion inhibitor.

The present study conducts the phase analysis, microstructural characteristics, and mechanical property evaluation on the as-cast and quenched Ti-15Mo-xFe alloys with high iron content ranging from 4 to 12 weight percent. All the four alloys were produced in a button-arc melting furnace. Heat treatment in the form of solution treatment was performed in a muffle furnace at a temperature of 1100°C, with a 1-hour holding time. The samples were rapidly quenched in ice-brine. Various characterization techniques were used to analyze samples both in the as cast and quenched conditions. X-ray diffractometer (XRD) was used to analyses the phases present in each alloy whereas the optical microscope (OM) was employed to track the microstructural evolution. The mechanical properties of the alloys were evaluated using a tensile test method while the micro-Vickers hardness measurements were conducted to evaluate hardness of the alloys. OM micrographs revealed equiaxed β grains and substructures in as-cast TMF0, dendritic structure, and equiaxed β grains with pores forming around the grain boundaries in TMF1, and micrograph full of dendrites and pores was observed in the as-cast TMF2 and TMF3 alloys. The quenched TMF0 showed only β equiaxed grains whereas TMF1, TMF2, and TMF3 revealed micrographs full of equiaxed grains of β phase with pores throughout the grain boundaries. The XRD patterns of cast TMF0 showed peaks belonging to the β and orthorhombic α″ martensitic phases and the quenched sample showed the bcc β phase only. The TMF1, TMF2, and TMF3 alloys in as-cast condition indicated peaks belonging to β , α″ and intermetallic B2 TiFe phases, however, their quenched samples showed the presence of β and Fe·Ti·O2 phases in TMF2 and TMF3 alloys. The tensile properties such as ultimate tensile strength (UTS) and elastic modulus (E) of as-cast TMF0 were 264 MPa and 79 GPa and these properties changed upon quenching to 411 MPa and 66 GPa respectively. The elastic modulus of TMF1 in as-cast condition was 74 GPa. The UTS and E of TMF1, TMF2, and TMF3 in as cast and quenched conditions were not recorded due to the fragility of the samples that failed prior to yielding any useful data. The micro-Vickers hardness in as cast and quenched conditions showed a similar trend with hardness increasing slightly upon quenching for TMF0, TMF1, and TMF3 alloys but slightly decreased in the case of TMF2. 6). The fracture surfaces of TMF0 exhibited both ductile and brittle fracture in as cast and quenched conditions whereas the only brittle fracture mode was observed in the TMF1, TMF2 and TMF3 alloys in both conditions.

The reuse of recycled crushed concrete aggregate (RCCA) and reclaimed asphalt pavement (RAP) can provide a sustainable solution for the disposal of C&amp;D materials instead of sending it to landfill. More importantly, it will save energy and reduce impact on the environment. Several states in USA are using RCCA and RAP as base materials for years, focusing on the quality of the recycled materials. The structure of Recycled Aggregate (RA) is more complex than Natural Aggregate (NA). RAs have old mortar adhered on them that forms a porous surface at interfacial transition Zone (ITZ) and prevents new cement mix from bonding strongly with the aggregates. The objective of this work was to correlate microstructural properties like micro-porosity, inter and intra aggregate pores with the unconfined compressive strength (UCS) of RAP and RCCA molds, mixed at different proportions. In this paper, the quantity of micro-pores and their effect on the strength of mixed materials is used as the basis of microstructural analysis of recycled concrete and reclaimed asphalt. Microstructural properties obtained from the analysis of scanning electron microscope (SEM) images were correlated with unconfined compressive strength. Intra-aggregate and inter-aggregate pores were studied for different ratios of cement treated mixture of RAP and RCCA. The results show that the number of pores in the mixture increases considerably by adding RAP, which eventually causes reduction in unconfined compressive strength. In addition, significant morphological and textural changes of recycled aggregates were observed by SEM image analysis.