We investigated the micro-threaded stem taper surface and the impact on premature failures, aseptic loosening, and infection. We have focused on the fretting, and crevice corrosion of micro-threaded tapers, as well as the characterization of microstructure and surface properties of two new and three retrieved Zweymüller stem tapers of cementless hip endoprostheses selected from a set of 45 stems. The retrievals examined were those in which the sole source of modularity with a metallic component was the head-stem taper interface between the Ti alloy taper stem and the ceramic head. To determine the surface chemistry and microstructures of both new and retrieved hip endoprostheses stem taper titanium alloy, scanning electron microscopy (SEM) was employed for morphological and microstructural analyses. At the same time, energy dispersive spectroscopy (EDS) was utilized for characterizing chemical element distribution, and electron backscattered diffraction (EBSD) was used for phase analysis. The micro-threated stem taper’s roughness for different manufacturers was investigated using an optical profilometer. Standard roughness pa-rameters Ra (average surface roughness) and Rz (mean peak to valley height of the roughness pro-file) were used in this investigation.Additionally, profile depth and peak spacing for different samples were investigated. The surface roughness results indicate no significant difference in roughness associated with varying survivorship times, ranging from 3 to 239 months, and across different manufacturers. Electrochemical studies revealed no fretting corrosion in retrieved stem tapers (ceramic head) that prematurely failed due to aseptic loosening after 239 months, infection after 3 months, and low-grade infection after a 32-month lifetime. Therefore, three retrieved ta-pers and two new ones for comparison underwent potentiodynamic measurements in Hank’s so-lution to ascertain the corrosion rate of new and retrieved stem taper surfaces. The results show a low corrosion rate for both new and retrieved samples that failed prematurely due to aseptic loosening. However, the corrosion rate of infected and low-grade infected tapers was higher. In conclusion, our study aligns with existing literature, suggesting that the use of ceramic heads de-creases the problem of taper corrosion and subsequently reduces premature failures in total hip arthroplasty.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

The endocannabinoid system (ECS) is a complex neuromodulatory network in the human body that have enormous impact in developing the central nervous system, as well as modulates various physiological processes. The ECS is made up of anandamide, 2-arachidonoylglycerol (2-AG), which are responsible for the synthesis and degradation of endocannabinoids, and enzymes such as FAAH and MAGL ensures the precise control over endocannabinoid levels. The ECS relies on CB1 receptors found in the central nervous system (CNS), and CB2 receptors found in the peripheral nervous system and immune cells. Dysregulation of the ECS has been associated with several health conditions, prompting investigations into its association with phytocannabinoids to harness their therapeutic potential. The ECS is intricately linked with the nervous system, and it is known to modulate neuronal activities in the CNS, influencing pain and mood modulation. The ECS is also associated with neuropathies-peripheral nerve damage leading to symptoms such as weakness, numbness and pain as evidenced in diabetic neuropathy, Guillain-Barré Syndrome, carpal tunnel syndrome, peripheral neuropathy, and postherpetic neuralgia. The focus of this review is on the interplay between 2-arachidonoylglycerol and anandamide amidohydrolase in neuropathy, elucidating their roles in pain regulation, inflammation, and specific neuropathies. The knowledge generated is expected to have broad implications, providing comprehensive insights into neuropathic conditions and how to improve on them. Ultimately, this understanding may lead to more effective treatments and improved quality of life for individuals affected by these conditions.

Music has the innate potential to reach all parts of the brain, stimulates certain brain areas which are not achievable through other modalities. Music Therapy (MT) is being used for more than a century to treat individuals who needs personalized care. MT optimizes motor, speech and language responsibilities of the brain and improves cognitive performance. Pervasive developmentdisorder (PDD) is a multifaceted, neuro developmental disorder and autism spectrum disorder (ASD) comes under PDD, which is defined by deficiencies in three principal spheres: social connection with others, communicative and normal movement skills. The conventional imaging studies illustrate reduced brain area connectivity in people with ASD, involving selected parts of the brain cortex. People with ASD express much interest in musical activities which engages the brain network areas and improves communication and social skills.The main objective of this review is to analyze the potential role of MT in treating the neurological conditions, particularly ASD. Evidence based studies have reported the extensive therapeutic application of music on various part of the brain in a nonverbal child with autism through hearing or making music.Hence we hypothesized that MT intervention can improve the communication capacity in people with ASD, than customary neurorestoration therapy alone.

Salmonella Typhimurium is a typical Gram-Negative bacterium associated with food-borne illness threatening public health. This pathogen is reported to have caused millions of infections and thousands of hospitalizations yearly in the United States alone. Salmonella Typhimurium has a sophisticated array of virulent factors, including its flagella, which contributes significantly to its pathogenicity. Cannabidiol (CBD), the non-psychoactive component of the cannabis plant, has attracted the interest of many researchers recently because of its antimicrobial properties. With the growing interest in exploring CBD’s antimicrobial properties, we, in this study, have delved into unravelling how prolonged exposure of Salmonella Typhimurium to CBD influences the expression of the flgA gene. We hypothesized that the exposure of Salmonella Typhimurium to CBD may result in flgA upregulation, causing the bacteria to withstand various stresses and potentially enhance its survival rates and pathogenicity. We have employed several assays, such as mRNA expression, motility assays, pH induction assays, nutrient starvation interventions, and biofilm analysis, to explore the influence of CBD on the pathophysiology of Salmonella Typhimurium. Our findings reveal that CBD-resistant strains exhibit enhanced resilience to extreme pH levels and motility and survive poorly under nutrient starvation, with more robust biofilm formation compared to the susceptible strains. The results contribute to the broader comprehension of CBD resistance mechanisms in bacteria. This work provides insight into the potential therapeutic interventions for controlling CBD-resistant bacterial infections. This study also underscores the essence of exploring novel alternative antimicrobial agents to tackle the ever-persistence of bacterial antibiotic resistance.

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) is a promising chemotherapeutic agent because of its selective apoptotic action on cancer cells. However, resistance to TRAIL-induced apoptosis remains a challenge in many cancers. The gintonin-enriched Panax ginseng extract fraction (GEF) has diverse pharmacological benefits. We explored the combined efficacy of GEF and TRAIL in inducing apoptosis in human renal cell carcinoma (RCC) cells. The effect of GEF treatment on viability, clonogenic potential, wound healing, and TRAIL-induced apoptotic signaling of RCC cells was studied in vitro. Our investigation revealed that GEF pre-treatment sensitized RCC cells to TRAIL-induced apoptosis, as evidenced by DNA fragmentation and cell proliferation, colony formation, and migration inhibition. This sensitization was linked to the upregulation of death receptors 4 and 5 and alterations in apoptotic protein expression; notably, decreased expression of Mu-2-related death-inducing gene, a novel anti-apoptotic protein. Our findings underscore the necessity of caspase activation for GEF/TRAIL-induced apoptosis using the pan-caspase inhibitor Z-VAD-FMK. It demonstrates that GEF sensitizes human RCC cells to TRAIL-induced apoptosis by upregulating DR4/5 and modulating apoptotic protein expression. These findings suggest a promising strategy for overcoming TRAIL resistance in cancer therapy and highlight the potential of GEF as a valuable adjunct to TRAIL-based treatments.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

Solar pasteurization, as a means of treating milk in remote rural areas without electrical power, is based on using solar energy to thermally inactivate pathogenic microorganisms at temperatures below the boiling point to maintain or improve milk quality. A solar milk pasteurizer of flat‐plate water‐heating glass acting as the solar collector, connected to a stainless-steel cylindrical milk vat, was constructed and evaluated in Navrongo, in the tropical savanna zone of Ghana, West Africa. The novel approach taken in this project is to integrate the solar collection and heat exchanger into a single unit using materials and fabrication techniques readily available in the developing world. The vat comprises a 1.5 mm thick stainless steel cylindrical tank, a 2.2 cm wide hot water jacket, and an outer layer of 5.0 mm thick aluminium foil insulation. Hot water produced by the collector was used for pasteurizing milk. The optimum quantity of milk that this device could pasteurize under the study conditions was 8 L. The device could pasteurize raw milk to a maximum temperature of 74 °C at 14:00 h GMT. The ambient temperature during the pasteurization ranged from 30 °C to 43 °C. The microbial analysis before and after the pasteurization was done, and the result shows that the total bacteria count before pasteurization was 6.6x10⁶ log CFU/mL per unit volume, and the total bacteria count after pasteurization was 1.0x10² log CFU/mL. By acceptable standards, the total bacteria count after pasteurization is within a safe range for consumption, and coliform counts were negative. The solar milk pasteurization system is cost-effective. Hence, it is appropriate for milk producers in arid pastoral areas without electricity to adopt the solar pasteurizer as an alternative to firewood as a fuel source for milk pasteurization. This approach can potentially create a cottage industry that may also play a crucial role as a water treatment technology that will improve the health of rural populations.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

The PLM concept implies the use of heterogeneous information resources at different stages of the product life cycle, the joint work of which allows you to effectively solve the problems of product quality and various costs. According to the principle of isomorphism of regularities of complex systems, an effective PLM system must have these regularities. Unfortunately, this principle is not often fundamental when designing PLM systems. The purpose of the work is to show, using a simple example, the principles of development, operation and use of an educational multi-agent PLM system, the main purpose of which is to study and research these regularities in the life cycle of a special threaded connection. The multi-agent approach to the development of a PLM system provides the necessary prerequisites for the emergence of system-wide regularities in it. The parallel work of agents is implemented using the actor model and the Ray Python-package. Agents for the logical inference of knowledge base facts, CAD/FEA/CAM/SCADA agents, agents for optimization by various methods, and other agents have been developed. Open source software was used to develop the system. Each agent has relatively simple behavior, implemented by its rule function, and can interact with other agents. The system can work in interactive mode with the user or in automatic mode according to a simple algorithm: the rule functions of all agents are executed until at least one of them returns a value other than None. Examples of the operation of the system are given and such system-wide regularities as emergence, historicity and self-organization are demonstrated in it.

Every individual at some point encounters the progressive biological process of aging which is considered one of the major risk factors for common diseases. The main drivers of aging are oxi-dative stress, senescence, and Reactive oxygen species (ROS). The renin-angiotensin-aldosterone system (RAAS) includes several systematic processes for the regulation of blood pressure which is caused by an imbalance of electrolytes. During activation of RAAS, binding of angiotensin II (ANG II) to angiotensin II type I receptor (AGTR1) activates intracellular NADPH oxidase to generate superoxide anions and promote uncoupling of endothelial NO synthase, which in turn decreases NO availability and increases ROS production. Promoting oxidative stress and DNA damage mediated by ANG II is tightly regulated. Individuals with sodium deficiency-associated diseases such as Gitelman syndrome (GS) and Bartter syndrome (BS) show down-regulation of inflammation-related processes and have reduced oxidative stress and ROS. Additionally, the histone deacetylase-Sirtuin-1(SIRT1) has a significant impact on the aging process with reduced activity with age. However, GS/BS patients generally sustain higher levels of SIRT1 activity than aged-matched healthy individuals. In this review, we highlight the importance of the hallmarks of aging, inflammation, and the RAAS system in GS/BS patients and how this might impact healthy aging. We further propose fu-ture research directions for studying the etiology of GS/BS at the molecular level using pa-tient-derived renal stem cells and induced pluripotent stem cells.

The intricate interplay between driver cognitive dysfunction, mental workload (MWL), and heart rate variability (HRV) provides a captivating avenue for investigation within the domain of transportation safety studies. This article presents a comprehensive review and examines cognitive hindrance stemming from mental workload and heart rate variability. It scrutinizes the mental workload experienced by drivers by leveraging data gleaned from prior studies that employed heart rate monitoring systems and eye tracking technology, thereby illuminating the correlation between cognitive impairment, mental workload, and physiological indicators such as heart rate and ocular movements. The investigation is grounded in the premise that the mental workload of drivers can be assessed through physiological cues, such as heart rate and eye movements. The study discovered that heart rate variability (HRV) and infrared (IR) measurements played a crucial role in evaluating fatigue and workload for skilled drivers. However, the study overlooked potential factors contributing to cognitive impairment in drivers and could benefit from incorporating alternative indicators of cognitive workload for deeper insights. Furthermore, investigated driving simulators demonstrated that an eco-safe driving Human-Machine Interface (HMI) significantly promoted safe driving behaviors without imposing excessive mental and visual workload on drivers. Recommendations were made for future studies to consider additional indicators of cognitive workload, such as subjective assessments or task performance metrics, for a more comprehensive understanding.

Knowledge is not merely the characteristic of certain pieces of information being deemed true and justifiable, but rather a process. Within an axiomatic system, the set of information that reaches the status of knowledge forms a universe that provides an interpretation of the reality one aims to describe. Language exchanges information through communication and the process of justification (exchange of information), if it consistently justifies a particular piece of information, it elevates it to knowledge. In this paper, we provide a framework for knowledge within an axiomatic model where we define the fundamental elements of communication and grammar. As a result, the structure dictates that knowledge, to be considered as such, must be investigateable by anyone who utilizes it in its entirety, both in form and content. Ultimately, the development of knowledge processing, referred to as \emph{knowmatics}, represents a clear evolution of the computer science that processes information (subset of knowledge).

Autism spectrum disorder (ASD) is a complex neurodevelopmental disorder, with a highly variable expression of phenotypes (restricted interest or activity and repetitive behavior in communication and social interactions), genes (mutation), markers (alteration of transcription) and pathways. Loss of function of the CC2D1A gene appears to primarily affect the brain, leading to a range of behavioral problems in humans. In our study published in 2020; we found that the expressions of miR-19a-3p, miR-361-5p, miR-150-5p, miR-3613-3p, miR-126-3p and miR-499a-5p were downregulated in the serum samples of autistic patients and their families. Here, acquired non-Mendelian hereditary character in a genetically defined mouse model of autism (Cc2d1a +/-) correlates with the transcriptional alteration of five miRNAs. We seek to test the hypothesis that miRNA levels are varying by changes in RNA/DNA structure during development, thereby creating transcription alteration. Behavioral tests were conducted on the offspring of Cc2d1a +/- mutant and control mice, such as novel object, social interaction, marble burying and tail suspension behavior. Two RNA fractions were isolated from mouse hippocampal tissues and sperm cells by standard TRIzol extraction: total RNA and fraction of RNA bound to DNA in the form of a DNA/RNA hybrid (R-loop). The expression levels of miR-19a-3p, miR-361-5p, miR-150-5p, miR-126-3p and miR-499a-5p were investigated by quantitative real-time RT-PCR. We report differences in the distribution of five miRNAs in the hippocampus between male and female mice in RNA fractions, particularly in colonies of Cc2d1a +/- mice. Furthermore, the number of miRNAs engaged in the DNA/RNA hybrid fraction is generally higher in the mutant pedigree than in the control group. On the other hand, in sperm both fractions are at lower levels than in controls. R-loops contribute to the physiology and pathology of organisms including human disease. Here we report a variation in five miRNA levels between gender and tissue. Our results suggest that the transcription levels of these five miRNAs are directly regulated by their RNA.

Non-conventional resonances, both acoustic and photonic, are found in metallic particles with a toroidal nanopropeller geometry that is generated by sweeping a three-lobed 2D-shape along a spiral with twisting angle, α. For both optical and acoustic cases, the spectral location of resonances experiences a red-shift as a function of α. We demonstrate that the optical case can be understood as a natural evolution of resonances as the spiral length of the toroidal nanopropeller increases with α, implying a huge helicity dependent absorption cross section. In the case of acoustic response, two red-shifting breathing modes are identified. Additionally, even a small α allows the appearance of new low-frequency resonances, whose spectral dispersion depends on a competition between length of the generative spiral and the pitch of the toroidal nanopropeller.

Aims: To study the effects of pyridoxal phosphate (PLP) on oxidative stress in isolated pancreatic acinar cells. We have previously shown that PLP has cytoprotective and insulinotropic effects on mice islet cells in vivo and in vitro studies. Main methods: Acinar cells were isolated from three months old WNIN male rats and were cultured in vitro for a period of 24 h in CO₂ incubator. Later the cells were divided into four groups as untreated (group 1), H₂O₂ treatment (group 2)_, PLP treatment (group 3) and PLP followed by H₂O₂ treatment (group 4). Cell viability was confirmed using MTT assays, oxidative stress levels were measured with ROS assay, change in different protein levels were recorded by flow cytometry. The acinar cells insulin secretion assay was performed with ELISA. The amylase protein expression was assessed using confocal microscopy. Key findings: The cell viability of acinar cell in group 1 was considered as 100%, while in group 2 it was reduced to 82% due to H₂O₂ effect, and in group 3 (99.8%) and group 4 (99.5%) were near to group 1 due to the cytoprotective effect of PLP. The ROS levels were increased by 1.47 folds in group 2, while PLP decreased to 1.02 fold in group 4, which was comparable with the changes in group 1. Beneficial effects of PLP were also observed from the increased expression levels of acinar cells are amylase -2.01, neurogenin-3-9.51, PDX-1- 23.6 and insulin-13.5 in group 3 compared to group 1. The specificity of PLP’s response was confirmed by amino oxy acetic acid (AOAA), a specific PLP inhibitor. The increased amylase protein localization with PLP was confirmed by confocal microscopy. Insulin secretion efficiency of acinar cells was observed to be 6.13 folds higher at basal and 24.63 fold higher at stimulated levels in group3 compared to group1. Significance: Our results advocate the antioxidant and cytoprotective effects of PLP on the pancreatic acinar cell along with increased pancreatic marker expressions of amylase,PDX-1, neurogenin-3 and insulin proteins.

The pulse duration in short-pulse schemes for Self-Amplified Spontaneous Emission Free Electron Lasers (SASE FELs) is limited by the FEL coherence time. A recently proposed concept allows to overcome the coherence time barrier and to get much shorter pulses. When the lasing part of an electron bunch is much shorter than the coherence time, one can suppress the radiation in the long main undulator while preserving microbunching within that short lasing slice. Then a short radiation pulse is produced in a relatively short radiator. A possible suppression method, an excessive reverse undulator taper, is discussed and illustrated numerically in this paper. We also performed first experimental tests of this method at the soft X-ray FEL user facility FLASH. The measured pulse duration approaches 1 fs (FWHM) at the wavelength of 5 nm.

Energy metabolism regulates the proliferation of stem cells by regulating energy production and the production of substrates through biosynthetic pathways. It is an important target for cell regulation and stem cell applications, and is crucial for determining the pluripotency and cell fate of stem cells. In this context, this article focuses on reviewing the latest research progress on the association between glucose metabolism, amino acid metabolism, fatty acid metabolism, and mitophagy with stem cell function, elucidating how key energy metabolism pathways affect stem cell function by regulating signal transduction and epigenetic modifications. In this review, we discuss the key factors affecting energy metabolism and their association with stem cell function. The integration of energy metabolism and stem cell fate regulation will open up a new path for future regenerative medicine practices.

Mesenchymal stem cells (MSCs) are one of the main residents in the bone marrow (BM), having an essential role in the regulation of hematopoietic stem cell (HSCs) differentiation and proliferation. Myelodysplastic syndromes (MDS) are a group of myeloid disorders impacting hematopoietic stem and progenitor cells (HSCPs) and characterised by BM failure, ineffective haematopoiesis, cytopenia, a high risk of transformation through the expansion of MDS clones together with additional genetic defects. It has been indicated that MSCs play anti-tumorigenic roles such as cell cycle arrest and pro-tumorigenic roles including induction of metastasis in MDS and leukaemia. Growing evidence has shown that MSCs have impaired functions in MDS, such as decreased proliferation capacity, differentiation ability, haematopoiesis support, immunomodulation function, and increased inflammatory alterations within the BM through some intracellular pathways such as Notch and Wnt and extracellular modulators secreted by MSCs abnormally, including increased expressions of inflammatory factors and decreased expressions of hematopoietic factors, contributing to the development and progression of MDS. Therefore, MSCs can be targeted for the treatment of MDS and leukaemia. However, it remains unclear what drives MSCs to behave abnormally. In this review, dysregulations in MSCs and their contributions to myeloid haematological malignancies will be discussed.

In tropical developing regions, typhoid fever and malaria often co-occur, posing serious health risks. The two illnesses have similar symptoms, which makes diagnosis and treatment more difficult. Through a thorough analysis of existing literature on typhoid fever, malaria, and co-infection, including research articles, case studies, and review papers, this review seeks to understand the dynamic interactions between typhoid fever and malaria co-infection. The review highlights important problems with co-infection between typhoid and malaria, such as higher morbidity and death, diagnostics-related challenges, and antibiotic resistance. Overlapping symptoms and limitations in current diagnostic tests impede accuracy. Treatment plans are made more difficult by the advent of typhoid strains that are resistant to drugs. The analysis concludes by highlighting the necessity of developing more sensitive and specific diagnostic methods in order to accurately diagnose co-infections. Going forward, the review emphasizes the need for more investigation into the immunological connections between malaria and typhoid illnesses. Essentially, this paper offers a thorough summary of the difficulties and possibilities related to co-infection between typhoid and malaria. It provides a framework for upcoming studies and initiatives that seek to improve public health and patient outcomes in the face of these intricately linked health problems.

Objectives: Social distancing measures are currently implemented to control COVID-19 pandemic in many countries, including Saudi Arabia. The aim of this study was therefore to evaluate the awareness and adherence of the Saudi population to these measures. Methods: A web-based questionnaire was designed with 16 questions (8 questions related to demographics, 3 in relation to awareness about social distancing and 5 related to overall practice of social distancing). Results: 5105 participants completed the survey [58.4% female, 66.3% young individuals (aged 18-37 years), 55.8% bachelor degree holders, and 51.0% from the western region]. The Saudi Ministry of Health (MOH) was the main source of information about COVID-19 for most participants (78.2%). High awareness (81.3%) regarding social distancing was observed, associated mainly with female participants, those from the middle region and those with high education and income. Overall implementation of social distancing was satisfactory (score 3.13/5), with 37.8% never leaving home during the home-stay period. Better adherence to social distancing was observed for female participants, higher degree holders and those aged over 38 years. Conclusions: Organised plans by the Saudi MOH have been effective in raising awareness and improving practice of social distancing among public. However, the observed lower practice of social distancing by individuals with lower education and income indicates the need for targeted interventions to achieve better outcome.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

Dendritic cell (DC) cancer vaccines are a promising therapeutic approach, leveraging the immune system to fight tumors. These vaccines utilize DCs' ability to present tumor-associated antigens to T cells, triggering a robust immune response. DC vaccine development has progressed through three generations. The first generation involved priming DCs with tumor-associated antigens or messenger RNA outside the body, showing limited clinical success. The second generation improved efficacy by using cytokine mixtures and specialized DC subsets to enhance immunogenicity. The third generation uses blood-derived DCs to elicit a stronger immune response. Clinical trials indicate that cancer vaccines have lower toxicity than traditional cytotoxic treatments. However, achieving significant clinical responses with DC immunotherapy remains challenging. Combining DC vaccines with immune checkpoint inhibitors (ICIs) such as anti-cytotoxic T-lymphocyte Antigen 4 and anti-programmed Death-1 antibodies has shown promise by enhancing T cell responses and improving clinical outcomes. These combinations can transform non-inflamed tumors into inflamed ones, boosting ICIs' efficacy. Current research is exploring new checkpoint targets like LAG-3, TIM-3, and TIGIT, considering their potential with DC vaccines. Additionally, engineering T cells with chimeric antigen receptors or T cell receptors could further augment the anti-tumor response. This comprehensive strategy aims to enhance cancer immunotherapy, focusing on increased efficacy and improved patient survival rates.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

The spread of micro- (MPs) and nanoplastics (NPs) in the environment has become a significant environmental concern, necessitating effective removal strategies. In this comprehensive scientific review, we examine the use of magnetic nanoparticles (MNPs) as a promising technology for the removal of MPs and NPs from water. We first describe the issue of MPs and NPs and their impact on the environment and human health. Then the fundamental principles of using MNPs for the removal of these pollutants will be presented, emphasizing that MNPs enable selective binding and separation of MPs and NPs from water sources. Furthermore, we provide a short summary of various types of MNPs that have proven effective in the removal of MPs and NPs. These include ferromagnetic nanoparticles, MNPs coated with organic polymers, as well as nanocomposites and magnetic nanostructures. We also review their properties, such as magnetic saturation, size, shape, surface functionalization and stability, and their influence on removal efficiency. Next, we describe different methods of utilizing MNPs for the removal of MPs and NPs. We discuss their advantages, limitations, and potential for further development in detail. In the final part of the review, we provide an overview of existing studies and results demonstrating the effectiveness of using MNPs for the removal of MPs and NPs from water. We also address challenges that need to be overcome, such as nanoparticle optimization, process scalability, and the removal and recycling of nanoparticles after the completion of the process. This comprehensive scientific review offers an extensive insight into the use of MNPs for the removal of MPs and NPs from water. With improved understanding and the development of advanced materials and methods, this technology can play a crucial role in addressing the issue of MPs and NPs and preserving a clean and healthy environment.

Energy from biogas is one of the most promising renewable energy sources. Significant, for technical, economic, and environmental reasons, is the construction of agricultural microgas plants next to households specialising in cattle rearing. The availability of free substrate makes it possible not only to produce one's electricity and heat but also to produce a more environmentally and human-friendly manure. The operation of biogas plants is, unfortunately, associated with technical problems. This paper presents the results of a study of the quality of electricity generated in an agricultural biogas plant built at a farm specialising in dairy cows, where the owner reported a problem with the voltage in the power supply network. Therefore, selected power quality parameters occurring at the connection point of the biogas plant were analysed in detail. As the authors' research showed, in the case in question, the agricultural biogas plant was connected via a cable with too small a conductor cross-section, which resulted in significant voltage exceedances, making it impossible to switch on the second of the biogas plant's generators. Replacement of the feed-in cable has enabled both generators to run, but significant fluctuations in the feed-in voltage values were still noticeable. Analysis of the subsequent measurements revealed the need for changes in the design of the digester itself. The proposal for change is to replace the two current digester mixers (each rated at 9 kW) with more mixers of lower power. The new mixers would operate in an alternating system, where only one would always be activated.

Recent discoveries of potential ice particles and ice-cemented regolith on celestial bodies like the Moon and Mars have ushered in new opportunities for developing technologies to extract water, facilitating future space missions and activities on these celestial surfaces. This study delves into the potential for water extraction from regolith through an experiment designed to test water recuperation from regolith simulant under varying gravitational conditions. The resultant water vapor extracted from the regolith is re-condensed on a substrate surface and collected in liquid form. Three types of substrates, hydrophobic, hydrophilic, and grooved, are explored. The system’s functionality was assessed during a parabolic flight campaign simulating three distinct gravity levels: microgravity, lunar gravity, and Martian gravity. Our findings reveal that the hydrophobic surface demonstrates the highest efficiency due to drop-wise condensation, and lower gravity levels result in increased water condensation on the substrates. This experiment aims to provide insights into in-situ water recovery, which is pivotal for establishing economically-sustainable water supplies for future missions.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

Corneal ulcers are a common and potentially vision-threatening condition in horses that can be challenging to treat with conventional therapies alone. This case report describes the successful treatment of a non-healing corneal ulcer in a 28-year-old Hispano-Bretón mare using the secretome derived from adipose tissue-derived mesenchymal stem cells (ASCs). Despite initial treatment with antibiotics, anti-inflammatory drugs, and surgical debridement, the corneal ulcer failed to heal properly, exhibiting persistent epithelial defects and stromal complications. As an alternative regenerative approach, the ASC secretome, a rich source of trophic factors, cytokines, and extracellular vesicles, was topically administered to the affected eye. Remarkably, within one week of secretome treatment, the clinical signs of blepharospasm and epiphora resolved, and the corneal ulcer exhibited complete re-epithelialization, regained transparency, and reduced neovascularization. No recurrence was observed during the 1.5-year follow-up period. This case highlights the potential therapeutic benefits of ASCs secretome in promoting corneal wound healing and suggests its promise as a novel cell-free therapy for treating refractory corneal ulcers in horses.

Candida albicans is an opportunistic fungus that becomes pathogenic and problematic under certain biological conditions. C.albicans may cause painful and uncomfortable symptoms, as well as deaths in immunocompromised patients. Therefore, early detection of c.albicans is essential. However, conventional detection methods are costly, slow and inaccessible to women in remote or developing areas. To address these concerns, we have developed a wearable and discrete naked-eye detectable, colorimetric platform for c.albicans detection. With some modification, this platform is designed to be directly adhered to existing feminine hygiene pads. Our platform is rapid, inexpensive, user-friendly, disposable and only requires three steps: i) addition of vaginal fluid onto sample pads; ii) addition of gold nanoparticle gel and running buffer, and iii) naked eye detection. Our platform is underpinned by selective thiolated aptamer-based recognition of 1,3-β-D glucan molecules- a hallmark of c.albicans cell walls. In the absence of c.albicans, wearable sample pads turn bright pink. In the presence of c. albicans, the wearable pads turn dark blue due to significant nanoparticle target-induced aggregation. We demonstrate naked eye colorimetric detection of 4.4 ×106 c.albicans cells per ml. We believe that this proof-of-concept platform has the potential to have a significant impact on women’s health, globally.

Cold plasma (CP) is an ionised gas containing excited molecules and ions, radicals, free electrons, and emits electric fields and UV radiation. CP is potently antimicrobial and can be applied safely to biological tissue, birthing the field of plasma medicine. Reactive oxygen and nitrogen species (RONS) produced by CP affect biological processes directly or indirectly via the modification of cellular lipids, proteins, DNA, and intracellular signalling pathways. CP can be applied at lower levels for oxidative eustress to activate cell proliferation, motility, migration, and antioxidant production in normal cells, mainly potentiated by the unfolded protein response, Nrf2-activated antioxidant response element and PI3K/Akt pathway, which also activates NFκB. At higher CP exposures, inactivation, apoptosis and autophagy of malignant cells can occur via degradation of PI3K/Akt and MAPK-dependent and -independent activation of the master tumour suppressor p53, leading to caspase-mediated cell death. These opposing responses validate a hormesis approach to plasma medicine. Clinical applications of CP are becoming increasingly realised in wound healing, while clinical effectiveness in tumours is currently coming to light. This review will outline advances in plasma medicine and compare the main redox and intracellular signalling responses to CP in wound healing and cancer.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 < 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

Microstructured surfaces are renowned for their unique properties, such as waterproofing and low adhesion, making them highly applicable in the biomedical field. These surfaces play a crucial role in influencing cell response by mimicking the native microenvironment of biological tissues. In this study, we engineered a series of biomimetic micropatterned surfaces using polydimethylsiloxane (PDMS) to explore their effects on primary breast cancer cell lines, contrasting these effects with those observed on conventional flat surfaces. The surface topography was varied to direct cells’ attachment, growth, and morphology. Our findings elucidate that surface-free energy is not merely a background factor but plays a decisive role in cell dynamics, strongly correlating with the spreading behaviour of breast cancer cells. Notably, on micropillar surfaces with high surface-free energy, an increase in the population of cancer cells was observed. Conversely, surfaces characterised by lower surface-free energies noted a reduction in cell viability. Moreover, the structural parameters, such as the gaps and diameters of the pillars, were found to critically influence cellular dispersion and adherence, underscoring the importance of the microstructures’ topography in biomedical applications. These insights pave the way for designing advanced microstructured surfaces tailored to specific cellular responses, opening new avenues for targeted cancer therapies and tissue engineering.

The objective of the study was to analyse the antimicrobial susceptibility trends of Spanish porcine bacteria to quinolones, cephalosporins and polymyxins. Isolates of Actinobacillus pleuropneumoniae, Pasteurella multocida, and Escherichia coli were isolated from sick pigs from 2019 to 2022. Antimicrobial susceptibility test was determined by minimal inhibitory concentration (MIC) following internationally accepted methodology. MIC categorization was based on distributing the range of MIC values in four categories being category one the most susceptible (lowest MIC value) and four the less susceptible one (highest MIC value). Moreover, clinical susceptibility (susceptible/resistant) was also determined according to CLSI and EUCAST clinical breakpoints. A logistic and multinomial logistic regression model was used to analyze the susceptibility data for dichotomized and categorized MIC data, respectively for any pair of antimicrobial/microorganism. In general terms, the antimicrobial susceptibility of pig bacteria to these antimicrobials remained stable or increased in the last four years in Spain. In the case of A. pleuropneumoniae and quinolones, it was observed a significant temporal trend where isolates from 2020 had significantly increased odds of being more susceptible than isolates from 2019. In the case of E. coli and polymyxins, a significant temporal trend was observed where isolates from 2020 and 2021 had significantly increased odds of being more susceptible than isolates from 2019 and 2020, respectively. Finally, a significant odd of being less susceptible was only observed for cephalosporins and E. coli for 2020 versus 2019, stagnating for the rest of study period. These results provide sound data on critical important antimicrobials in swine medicine.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Adipose tissue-derived stem cells (ADSCs) represent a subset of mesenchymal stem cells in every adipose compartment throughout the body. ADSCs can differentiate into various cell types, including chondrocytes, osteocytes, myocytes, and adipocytes. Moreover, they exhibit a notable potential to differentiate in vitro into cells from other germinal lineages, including endothelial cells and neurons. ADSCs have a wide range of clinical applications, from breast surgery to chronic wounds. Furthermore, they are a promising cell population for future tissue-engineering uses. Accumulating evidence indicates decreased proliferation and differentiation potential of ADSCs with increasing age, body mass index, diabetes mellitus, metabolic syndrome, or exposure to radiotherapy. Therefore, recent literature thoroughly investigates this cell population's senescence mechanisms and how they can hinder their possible therapeutic applications. This review will discuss the biological mechanisms and the physio-pathological causes behind ADSC senescence and how they can impact cellular functionality. Moreover, we will examine the possible strategies to invert these processes, re-establishing the full regenerative potential of this progenitor population.

During pregnancy, profound physiological changes occur in the maternal body, including those affecting oral health. Dental stem cells (DSCs) have emerged as promising candidates for regenerative therapies in dentistry. This manuscript delves into the intricate interplay between DSC behavior and maternal oral health during pregnancy. We provide an overview of current knowledge concerning the impact of pregnancy on DSCs, highlighting their potential roles in maintaining oral homeostasis and responding to pathological conditions. Additionally, we identify key research gaps and propose future directions for investigating novel therapeutic strategies leveraging DSCs to improve maternal and fetal oral health outcomes. By elucidating this relationship, we aim to pave the way for innovative approaches in preventive and regenerative dentistry tailored to the unique needs of pregnant women.

Pure titanium is limited to be used in biomedical applications due to its lower mechanical strength compared to its alloy counterpart. To enhance its properties and improve medical implants feasibility, advancements in titanium processing technologies are necessary. One such technique is equal channel angular pressing (ECAP) for its severe plastic deformation (SPD). This study aimed to surface modify commercially pure titanium using micro arc oxidation (MAO) technology and mineral solutions containing Ca and P. The composition and shape of the changed surface were characterized using X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The weight % of Ca and P in the coating was determined using Energy Dispersive Spectroscopy (EDS), and the corrosion resistance was evaluated through potentiodynamic measurement. The behavior of human dental pulp cell and periodontal cell behavior was also studied through a biomedical experiment over a period of 1-, 3-, and 7-days using trypsin as the culture medium and ELISA as the observation method. This study showed that the mechanical grain refinement method and surface modification significantly improved the biomechanical properties of commercially pure (CP) Titanium. Although the results showed variations in the absorbance values of cells cultured on different surfaces, this study provides valuable insights into pulp cell behavior and advances the field of biomedical research.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Simple Summary: This review explores the origin of Leukemic Stem-Like Cells (LSLCs) from (Very) Small Leukemic Stem-Like Cells ((V)SLSLCs) and Cancer Stem Cells (CSCs) from trans-formed Very Small Embryonic-Like Stem Cells (VSELSCs). Understanding this relation is a step toward uncovering the mechanisms behind cancer and leukemia initiation and development. We explore how these very small precursor cell stages might contribute to the initiation and progres-sion of cancer as well as leukemia with a focus on Acute Myeloid Leukemia (AML) as a model. Abstract: Recent experimental findings indicate that CSCs originate from transformed VSELSCs, which are early precursor stages of healthy stem cells. This discovery marks a crucial step in understanding the mechanisms that drive cancer development and initiation. Our team's follow-up studies on leukemia, lung cancer, and healthy embryonic kidney cells have, for the first time, identified stag-es resembling very small precursor stem cells in continuously growing cell lines. These findings suggest the existence of (Very) Small Cancer Stem Cells ((V)SCSCs) or (V)SLSCs within respective subpopulations of CSCs and LSCs in vivo. In this review, we explore theoretical examples of how leukemia progresses through various stages, highlighting the role of these very small precursor cells as fundament primitive stages. We also discuss the potential implications of further research into these unique cellular stages for advancing cancer and leukemia treatment and prevention strategies.

Due to their wide range of uses in modern technology, nanomaterial’s of silver metallic (Ag-NPs) have engaged considerable concern, driving significant research with development efforts. This study focuses on investigating the antimicrobial properties of Ag-NPs, encompassing their production, characterization, and biological aspects. The eco-friendly extracellular biosynthetic method employed in this work utilized extracts from the marine fungus Aspergillus flavus MK4 as reducing agents for nanoparticle synthesis. Analyzing the colloidal Ag-NPs using UV-visible spectroscopy revealed a peak in absorbance at 460 nm, indicating the presence of plasmonic properties. The electrons imaging of internal structure (TEM) elucidated spherical shape of the Ag-NPs by 15 nm size. Testing against bacterial diversities (Gr-ve & Gr+ve) revealed potent antibacterial and antifungal efficacy. Cytotoxicity versus HepG-2 cell line was assessed using the MTT assay, and antioxidant properties were examined through the radical scavenging (DPPH) assay. In wise of their conceivable applications in the fields of antibacterial, anticancer, and wound-healing, the Ag-NPs that were synthesized exhibit promising features. With its powerful ability to synthesize silver nanoparticles (Ag-NP), Aspergillus flavus MK4 Aspergillus flavus MK4 can generate nanoparticles extensively characterized, demonstrating their antibacterial, antioxidant, anticancer, and wound-healing properties.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

The increase in the rate and prevalence of diseases associated with the localized and general loss of bone mass calls for an investigation into therapeutic alternatives that largely involve the de-velopment of new biomaterials and cell therapy, converting tissue bioengineering into a prom-ising option. An experimental model of a critical mandibular lesion in rats has been used to study bone re-generation by treating the ostectomy with the biomaterials Evolution® and Gen-Os® (OsteoBiol®, Italy) combined, or not, with dental pulp stem cells (DP-MSC). The results obtained through the Micro-CT and histological study reveal the almost complete re-covery of the lesion in the group with DP-MSC. These results are supported by increases in endoglin, TGF-β, protocollagen I, parathormone, and calcitonin, generating an environment of bone generation and development when combining Evolution® and Gen-Os® (OsteoBiol®, Italy) with DP-MSC. These promising results confirm the transcendental role of DP-MSC in combina-tion with osteogenic biomaterials for bone regeneration, and warrant further studies, including its assessment in clinical trials.

Osteoporosis (OP), a prevalent skeletal disorder characterized by compromised bone strength and increased susceptibility to fractures, poses a significant public health concern. This review aims to provide a comprehensive analysis of the current state of research in the field, focusing on the application of proteomic techniques to elucidate diagnostic markers and therapeutic targets for OP. The integration of cutting-edge proteomic technologies has enabled the identification and quantification of proteins associated with bone metabolism, leading to a deeper understanding of the molecular mechanisms underlying OP. In this review, we systematically examine recent advancements in proteomic studies related to OP, emphasizing the identification of potential biomarkers for OP diagnosis and the discovery of novel therapeutic targets. Additionally, we discuss the challenges and future directions in the field, highlighting the potential impact of proteomic research in transforming the landscape of OP diagnosis and treatment.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

: Microplastics and nanoplastics (MNPs) are becoming an increasingly severe global problem due to their widespread distribution and complex impact on living organisms. Apart from their environmental impact, the effects of MNPs on living organisms have also continued to attract attention. The harmful impact of MNPs has been extensively documented in marine invertebrates and larger marine vertebrates like fish. However, the research on the toxicity of these particles on mammals is still limited, and their possible effects on humans are poorly understood. Considering that MNPs are commonly found in food or food packaging, humans are primarily exposed to them through ingestion. It would be valuable to investigate the potential harmful effects of these particles on gut health. This review focuses on recent research exploring the toxicological impacts of micro- and nanoplastics on the gut, as observed in human cell lines and mammalian models. Available data from various studies indicate that the accumulation of MNPs in mammalian models and human cells may result in adverse consequences, in terms of epithelial toxicity, immune toxicity, and disruption of gut microbiota. The paper also discusses the current research limitations and prospects in this field, aiming to provide a scientific basis and reference for further studies on the toxic mechanisms of micro- and nanoplastics.

Microorganisms drive the biogeochemical cycles that link abiotic and biotic processes in the aqueous environment and are intricately associated with plastic debris. The detection of microplastics in water and sediment introduces new concerns as small particle size allows for yet unconsidered pathways for plastics in the food web and element cycles. In this review, we present current knowledge of microbe-plastic interactions and summarize the potential impact of biogeochemical processes on plastic distribution, cycling, transport, and sedimentation. We explore how microbe-plastic interactions influence the exposure of consumers to plastics and plastic degradation products. Key methods used to elucidate biofilm development, microbial biodegradation, and plastic detection in the aqueous environment are discussed. Finally, we comment on potential future questions and research directions needed to further define the role of microorganisms in the environmental fate of microplastics.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

In this work the close relation between vorticity and micro-rotation in micropolar flows in Rn (n = 2 or 3) is identified and used to explain the faster decay by t^(-1/2) of the angular velocity of the micro-rotation of fluid particles, as well as establishing its optimality. For this purpose important upper and lower bounds for Leray solutions in homogeneous Sobolev spaces are derived, using the monotonicity approach recently introduced by the authors for dissipative systems in general. Several related results of interest are also given along the discussion.

Segmental bone defects caused by trauma, infection, tumor resection or osteoporotic fractures present significant surgical treatment challenges. Host bone autograft is considered the gold standard to restore function but comes with the cost of harvest site comorbidity. Allograft bone is a secondary option but has its own limitations in incorporation with host bone as well as cost. Therefore, developing new bone tissue engineering strategies to treat bone defects is critically needed. In the past three decades, the use of stem cells delivered with different scaffolds or growth factors for bone tissue engineering has made tremendous progress. Many varieties of stem cells have been isolated from different tissues for use in bone tissue engineering. This review summarizes the progress in using different postnatal stem cells including bone marrow mesenchymal stem cells, muscle-derived stem cells, adipose-derived stem cells, dental pulp stem cells/periodontal ligament stem cells, periosteum stem cells, umbilical cord-derived stem cells, peripheral blood stem cells and urine-derived stem cells for bone tissue engineering and repair. This review also summarizes the progress using exosomes or extracellular vesicles delivered with various scaffolds for bone repair. The advantages and disadvantages of each type of stem cell are also discussed and explained in detail. It is hopeful in the future that these preclinical results will translate into new therapies for bone defect repair.

Micro-combs [1-4] - optical frequency combs generated by integrated micro-cavity resonators – offer the full potential of their bulk counterparts [5,6], but in an integrated footprint. The discovery of temporal soliton states (DKS – dissipative Kerr solitons) [4,7-11] as a means of mode-locking micro-combs has enabled breakthroughs in many fields including spectroscopy [12,13], microwave photonics [14], frequency synthesis [15], optical ranging [16,17], quantum sources [18,19], metrology [20,21] and more. One of their most promising applications has been optical fibre communications where they have enabled massively parallel ultrahigh capacity multiplexed data transmission [22,23]. Here, by using a new and powerful class of micro-comb called “soliton crystals” [11], we achieve unprecedented data transmission over standard optical fibre using a single integrated chip source. We demonstrate a line rate of 44.2 Terabits per second (Tb/s) using the telecommunications C-band at 1550nm with a spectral efficiency – a critically important performance metric - of 10.4 bits/s/Hz. Soliton crystals exhibit robust and stable generation and operation as well as a high intrinsic efficiency that, together with a low soliton micro-comb spacing of 48.9 GHz enable the use of a very high coherent data modulation format of 64 QAM (quadrature amplitude modulated). We demonstrate error free transmission over 75 km of standard optical fibre in the laboratory as well as in a field trial over an installed metropolitan optical fibre network. These experiments were greatly aided by the ability of the soliton crystals to operate without stabilization or feedback control. This work demonstrates the capability of optical soliton crystal micro-combs to perform in demanding and practical optical communications networks.

This study aimed to investigate the potential of Cord Blood Stem Cell-derived exosome vesicles (CBSC-EVs) in regulating cancer growth and preventing cellular damage. The study aimed to examine the effects of CBSC-EVs on CHL1 cancer cells and healthy fibroblasts. The study results reveal that CBSC-EVs have an anti-cancer/antioxidant effect on CHL1 cancer cells without inducing any toxic effects on healthy lymphocytes. Further analysis of CBSC-EVs revealed the presence of seven miRNAs (noncoding RNA molecules), including three from the Let 7 family, two from the Let 5 family, and two novel miRNAs. The function of the novel miRNAs was the main focus of the study. To assess the efficacy of CBSC-EVs, CHL1 cells (a type of malignant melanoma cell line) and human fibroblasts were grouped into different treatments. One group of those cell lines were treated with CBSC-EVs, and in the second group, the cells were transfected with either miRNA inhibitor Novel 1 (miRNA IN1) plus CBSC-EVs or miRNA inhibitor Novel 2 (miRNA IN2) and CBSC-EVs to knock down those novel miRNAs in the CBSC-EVs. Therefore, by comparing these groups, the function of novel miRNAs is more understandable. In this study, the Comet assay was employed to evaluate cancer cells' DNA damage and CCK8 to measure cell viability. The findings revealed that CBSC-EVs caused an increase in DNA damage in CHL1 cells compared to cells without treatment (p

The stromal vascular cell fraction (SVF) of visceral and subcutaneous adipose tissue (VAT and SAT) has increasingly come into focus in stem cell research, since these compartments represent a rich source of multipotent adipose-derived stem cells (ASCs). ASCs exhibit a self- renewal potential and differentiation capacity. Our aim was to study the different expression of embryonic stem cell markers NANOG, SOX2 and OCT3/4 and to evaluate if there exists a hierarchal role in this network in ASCs derived from both SAT and VAT. ASCs were isolated from SAT and VAT biopsies of 72 consenting patients (23 men, 47 women; age 45 ± 10; BMI between 25 and 30 range) undergoing elective open-abdominal surgery. Sphere-forming capability was evaluated by plating cells in low adhesion plastic. Stem cell markers CD90 and CD105 were analyzed by flow cytometry and stem cell transcription factors NANOG, SOX2 and OCT3/4 were detected by immunoblotting and Real-Time PCR. NANOG, SOX2 and OCT3/4 interplay was explored by gene silencing. ASCs from VAT and SAT confirmed their mesenchymal stem cell (MSC) phenotype expressing the specific MSC markers CD90, CD105, NANOG, SOX2 and OCT3/4. NANOG silencing induced a significant OCT 3/4 (70% ± 0.05) and SOX2 (75% ± 0.03) down-regulation whereas SOX2 silencing did not affect NANOG gene expression. Adipose tissue is an important source of MSC, and siRNA experiments endorse a hierarchical role of NANOG in the complex transcription network that regulates pluripotency and plasticity.

Forty-eight Pasteurella multocida isolates were recovered from porcine pneumonic lungs collected in Norwestern Spain (2017- 2019). These isolates were characterized for their minimal inhibition concentrations to twelve antimicrobial agents and for the appearance of eight resistance genes: tetA, tetB, blaROB1, blaTEM, ermA, ermC, mphE and msrE. Relevant resistance percentages were shown to teracyclines, sulphamethoxazole/trimethoprim and tiamulin, thus suggesting that P. multocida isolates were mostly susceptible to amoxicillin, ceftiofur, enrofloxacin, florfenicol, marbofloxacin and macrolides. 29.2% of isolates were resistant to more than two antimicrobials. The tetracycline resistance genes (tetA and tetB) were detected in 22.9% of the isolates, but none was positive to both simultaneously; blaROB1 and blaTEM genes were found in one third of isolates but both genes were detected simultaneously in only one isolate. ermC gene was observed in 41.7% of isolates, a percentage that decreased until 22.9% for msrE; finally, ermA was harboured by 16.7% and mphE was not found in any of them. Six clusters were established based on hierarchical clustering analysis on antimicrobial susceptibility for the twelve antimicrobials. Generally, it was unable to foresee the antimicrobial susceptibility pattern for each family and the association of each particular isolate inside the clusters established from the presence or absence of the resistance genes analyzed.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

The chemical investigation of the anti-yeast methanol extract from the stem bark of Terminalia mantaly led to the isolation of seven compounds: 3-O-methyl-4-O-α-rhamnopyranoside ellagic acid (1), 3-O-mehylellagic acid (2), arjungenin or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid (3), arjunglucoside or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid glucopyranoside (4), 2α,3α,24-trihydroxyolean-11,13(18)-dien-28-oïc acid (5), stigmasterol (6), stigmasterol 3-O-β-D-glucopyranoside (7). Their structures were established by means of spectroscopic analysis and comparison with published data. Compounds 1-5 were tested in vitro for activity against three pathogenic yeast isolates, Candida albicans, Candida parapsilosis and Candida krusei. The activity of compounds 1, 2 and 4 were comparable to that of the reference compound fluconazole (MIC values below 32 µg/ml) against the three tested yeast isolates. They were also tested for inhibitory properties against four enzymes of metabolic significance: Glucose-6-Phosphate Deshydrogenase (G6PD), human erythrocyte Carbonic anhydrase I and II (hCA I and hCA II), Glutathione S-transferase (GST). Compound 4 showed highly potent inhibitory property against the four tested enzymes with overall IC₅₀ values below 4 µM and inhibitory constant (Ki) <3 µM.

How hematopoietic stem and progenitor cell (HSPC) fate decisions are affected by genetic alterations acquired during AML leukemogenesis is poorly understood and mainly explored in animal models. Here, we studied isocitrate dehydrogenases (IDH) genes mutations in the human model of HSPC and provide a review of the literature on this topic. IDH1/2 mutations occur in ~20% of AML, are recognized among the mutations earliest acquired during leukemogenesis, and are target of specific inhibitors (ivosidenib and enasidenib, respectively). In order to investigate the direct effects of these mutations on the HSPC we expressed by lentiviral transduction either IDH1-R132H or IDH2-R140Q mutants into human CD34+ healthy donor cells and analyzed the colony-forming unit (CFU) ability. CFU ability was dramatically compromised with a complete trilineage block of differentiation. Strikingly, the block was reversed by the specific inhibitors, confirming it was a specific effect induced by the mutants. In line with this observation, the CD34+ leukemic precursors isolated from a patient with IDH2-mutated AML at baseline and during enasidenib treatment showed over time a progressive and marked improvement of their fitness in terms of CFU ability and propensity to differentiate, attaining clonal trilinear reconstitution of hematopoiesis and complete hematological remission.

Energy transition is one of the greatest challenges facing humanity today. All micro, small, medium and large enterprises in operation will have to face it, and some can al-ready boast the first successes in this regard. This paper focuses on the involvement of these smallest players in energy transition. Micro and small entities are the largest part of the economy, having a great influence on its development. Looking at the wide scale of their activities, these entities are distinguished by a specific owner-manager relationship. This means that the final decision-making is influenced by business goals, but also by the manager's approach, their awareness of changes, and personal and other factors. Based on a structured and standardized survey questionnaire, the research was carried out using the Computer-Assisted Telephone Interviewing technique between April and May 2022 among owners of micro and small enterprises operating in Poland. The survey showed that active engagement of micro and small enterprises in energy efficiency initiatives is related to their market success and financial health.

Once discovered, cancer stem cells have become a hot topic in the research of cancer therapy. These cells possess stem cell-like self-renewal and differentiation capacities and are important factors that dominate cancer metastasis, therapy- resistance and recurrence. What's worse, their own characteristics make them difficult to be eliminated. Colorectal cancer is the third most common cancer and the second leading cause of cancer death worldwide. Targeting colorectal cancer stem cells (CRCSCs) can inhibit colorectal cancer metastasis, enhance therapeutic efficacy, and reduce recurrence. Here, we introduced the origin, marker proteins, identification, cultivation and research techniques of CRCSCs, summarized the signaling pathways that regulate the stemness of CRCSCs, such as Wnt, JAK/STAT3, Notch, and Hh signaling pathway. In addition to these, we also reviewed anti-CRCSC drugs targeting signaling pathways，markers，and other regulators in recent years. These will help researchers gain insight into the current agents targeting to CRCSCs, explore new cancer drugs, and propose potential therapy.

Stem cells can be used in cellular therapy. This happended in order to replace damaged cells or having aim to regenerate organs. The definition of stem cells can be extended. From this point of view, we can mention taking in consideration the idea in which it is known that these cells form the base of the building body. More than, we can mention that stem cells are characterized by two knowing properties namely differentiation and self renewal. Based on the observation that differentiation of adult stem cells into specific derivative scan be controlled by laboratory techniques, it is anticipated that adult stem cells may become the basis of therapies for many, and various types of medical conditions. Taking on stem cells, regenerative medicine (RM) it is known as being one of the hottest topics in biotechnology nowadays. From this purpose, stem cells can be used in regenerative medicine (RM). The principles of regeneration are found in different types of cultures, from long time ago. As an interdisciplinary field of research, regenerative medicine, play a great role in tissues and organs damaged reparation with a higher potential in transplantation if necessary.

Cancer stem cells (CSCs) are one of the cell types that account for cancer heterogeneity. They arrest in the G0 phase and generate non-CSC progeny by self-renewing and pluripotency activity, resulting in tumor recurrence, metastasis, and chemoresistance. One CSC can stimulate tumor relapse and can re-grow a metastatic tumor. So, CSC is a promising target for eradicating tumors, and developing an anti-CSC method has become a top priority in cancer therapy. In recent years competing endogenous RNA (ceRNA) have emerged as an important class of post-transcriptional regulators that affect gene expression via competition for microRNA (miRNA) binding. Furthermore, aberrant ceRNA expression is associated with tumor progression. To overcome therapeutic resistance due to CSCs, we need to improve our existing understanding of the mechanisms by which ceRNAs are implicated in CSC-related relapse. Thus, this review was designed in order to discuss the role of ceRNAs in CSCs function. We reviewed the role of ceRNAs in acquiring CSCs characteristics in the form of different pathways including Rho GTPase/F-actin_ Yes-associated protein (YAP)/transcriptional co-activator with PDZ-binding motif (TAZ) (Hippo), Wnt/β-catenin pathway, transforming growth factor (TGF)-b–urothelial carcinoma-associated 1 (UCA1)–Slug pathway, etc. Finally, considering the comprehensive impacts of the ceRNA network on different pathways, a treatment strategy driving the ceRNA network might be effective. Targeting ceRNAs may open the path for new cancer therapeutic targets and can be used in clinical research.

Mitochondria are highly dynamic organelles that continuously change their shape. Their main function is ATP production; however, they are additionally involved in a variety of cellular phenomena, such as apoptosis, cell cycle, proliferation, differentiation, reprogramming, and aging. The change in mitochondrial morphology is closely related to the functionality of mitochondria. Normal mitochondrial dynamics are critical for cellular function, embryonic development, and tissue formation. Thus, defect in proteins involved in mitochondrial dynamics that control mitochondrial fusion and fission can affect cellular differentiation, proliferation, cellular reprogramming, and aging. Here we review the processes and proteins involved in mitochondrial dynamics and its various associated cellular phenomena.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

Submucosal invasion is a critical step in gastric cancer (GC) progression, which greatly enhances metastasis risk. Cancer stem cells are responsible for invasion, metastasis, and tumor growth. To identify stem cell-related markers associated with submucosal invasion in GCs, we investigated the expression of candidate cancer stem cell (CSC) markers (CD133, CD44, and ALDH1A) and intestinal stem cell (ISC) markers (EPHB2, OLFM4, and LGR5) in early GCs with submucosal invasion. Remarkably, expression of all ISC markers and CD133 was frequently confined to the basal area of the lamina propria (basal pattern) in mucosal cancer. The proportion of stem cell marker-positive cells substantially increased during submucosal invasion. Given that ISC markers are restricted to the crypt base of the normal intestinal mucosa, these findings suggest that many early GCs may retain hierarchical characteristics. CD44 expression showed a focal pattern, ALDH1A was predominantly expressed diffusely, and there was no expansion of CD44 or ALDH1A expression in the submucosal cancer cells. RSPO2 from muscularis mucosa seem to be partly responsible for the increased expression of ISC markers in GC cells at the basal areas. We also found that ISC markers were correlated with CDX2 expression in GCs, indicating that ISC markers are involved in the intestinal differentiation in GCs. Interestingly, ISC markers (EPHB2 and OLFM4) and CD133 showed a positive impact on clinical outcomes. In particular, the prognostic value of EPHB2 was significant for intestinal-type GCs in a multivariate analysis. In summary, ISC markers and CD133 showed a basal distribution pattern along with enhanced expression in submucosal invading cells in early GCs. EPHB2 was an independent prognostic marker in intestinal-type GCs.

Various tissue resident stem cells are receiving attention from basic scientists and clinicians as they hold certain promise for regenerative medicine. This paper is intended to clarify and facilitate the understanding, development and adoption of regenerative medicine in general and specifically of therapies based on unmodified, autologous adipose-derived regenerative cells (UA-ADRCs). To this end, results of landmark experiments on stem cells and stem cell therapy performed in the labs of the authors are summarized, the most intriguing of which are the following: (i) vascular associated mesenchymal stem cells (MSCs) can be isolated from different organs (adipose tissue, heart, skin, bone marrow and skeletal muscle) and differentiated into ectoderm, mesoderm and endoderm, providing significant support for the hypothesis of the existence of a small, ubiquitously distributed, universal vascular associated stem cell with full pluripotency; (ii) the orientation and differentiation of MSCs are driven by signals of the respective microenvironment; and (iii) these stem cells irrespective of the tissue origin exhibit full pluripotent differentiation potential without any prior genetic modification or the need for culturing. They can be obtained from a small amount of adipose tissue when using the appropriate technology for isolating the cells, and can be harvested from and re-applied to the same patient at the point of care without the need for complicated processing, manipulation, culturing, expensive equipment, or repeat interventions. These findings demonstrate the potential of UA-ADRCs for triggering the development of an entire new generation of medicine for the benefit of patients and of healthcare systems.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

When describing the tribological behaviour of technical surfaces, the need for full length scale microtopographic characterization often arises. The self-affine of surfaces and the characterization of self-affine by a fractal dimension and its implantation into tribological models are commonly used. The goal of our present work was to determine the frequency range of fractal behaviour of surfaces by analysing the microtopographic measurements of a brake plunger. We also wanted to know if the bifractal and multifractal behaviour can be detected in real machine parts. As a result, we developed a new methodology for determining the fractal range boundaries to separate the nano- and micro-roughness. In order to reach our goals, we used atomic force microscope (AFM) and stylus instrument to provide measurements in wide frequency range (19 nm - 3 mm). As a result of the power spectral density (PSD) based fractal evaluation, it was found that the examined surface could not be characterized by a single fractal dimension and that we developed a methodology for stopping the margin of validity of each fractal dimension, and we also developed a methodology for determining the limits of validity of certain fractal dimensions.

A micro decision-making utility model under uncertainty is presented as a complementary foundation for macro coronavirus models. The micro model consists of two functions, a risk averse utility function depending on wellness and a wellness random output which is a function of the input variable called “treatment” consisting of such elements as social distance, washing hands, wearing a face mask, and others. The decision maker selects a level of treatment that maximizes her/his expected utility, given the probabilities of the respective outputs. The focus is on how changes in a person’s psychological attitude towards the macro determined (announced) probabilities affects the optimum results of the model. Such changes create a micro-macro dynamic interaction which is briefly outlined. A short discussion of the model’s behavioral implications for health policy is also given.

Pluripotent stem cells (PSCs) can differentiate into three germ layers and diverse autolo-gous cell lines. Being among the most commonly used large domesticated hoofed animals and serving as a vital source of food and bioreactors, cattle are among the many species in which PSCs have been developed. Bovine PSCs (bPSCs) are the "seed cells" of regenerative science and have immense potential to advance species propagation, genetic engineering, and disease treatment. Moreover, they can aid in screening new drugs for efficacy and toxicity, model human diseases, and establish a sustainable agricultural system that can cater to the needs of the growing global population. Establishing stable bPSCs in vitro has been a critical scientific challenge, and researchers have made numerous attempts to address this issue. This review primarily delves into the current research progress of bPSCs, the challenges faced, and their potential applications.

During early embryonic development, fertilized one-cell embryos develop into preimplantation blastocysts and subsequently establish three germ layers through gastrulation during post-implantation development. In recent years, stem cells have emerged as a powerful tool to study embryogenesis and gastrulation without the need for eggs, allowing the generation of embryo-like structures known as synthetic embryos or embryoids. These in vitro models closely resemble early embryos in terms of morphology and gene expression and provide a faithful recapitulation of early pre- and post-implantation embryonic development. Synthetic embryos can be generated through a combinatorial culture of three blastocyst-derived stem cell types, such as embryonic stem cells, trophoblast stem cells, and extraembryonic endoderm cells, or totipotent-like stem cells alone. This review provides an overview of the progress and various approaches in studying in vitro embryogenesis and gastrulation using stem cells. Furthermore, recent findings and breakthroughs in synthetic embryos and gastruloids are outlined. Despite ethical considerations, synthetic embryo models hold promise for understanding mammalian (including human) embryonic development and have potential implications for regenerative medicine and developmental research.

According to the ECCB, cancer represents the transition of a genomically damaged multicellular cell to a lower level of cell organization, controlled by the ancestral gene regulatory network (GRN) from the ancestral compartment of human and metazoan genomes. Cancer adopts ancient mechanisms and rules of the common ancestor, similar to those observed in parasitic amoebae. In cancer, the productive cell line generating CSCs is a non-gametogenic cancer germline. This germline proliferates through asymmetric cell division (ACD phenotype). CSCs lack proliferative capacity; they persist in hypoxic niches in a quiescent cell state or transition to an amplifying cell state that performs cyst-like polyploidization cycles, giving rise to precursors and CSCs capable of differentiation. Malignization arises from genomically dysfunctional tetraploid germline cells (DSCD phenotype) that proliferate in a precancerous stage through symmetric cell cycles. DSCD progeny undergo homotypic fusion, forming multinucleated genome repair syncytia (MGRS pathway) driving carcinogenesis. During tumorigenesis, metastasis, and recurrence, subsequent germline clones initiate a cascade of increasingly pathogenic CSCs through mechanisms such as heterotypic cell fusion, soma-to-germ transition, and polyploid giant cell structures (PGCCs). Irradiation and chemotherapies drive some of the very few surviving but dysfunctional CSCs through a PGCC repair pathway homologous to the MGRS pathway of carcinogenesis. The large number of PGCCs during metastasis and recurrence results from the perpetual germline cell damage and CSC poverty induced by oxygen levels above 6.0% O2 (germline hyperoxia).

We report a photonic-based radio frequency (RF) arbitrary waveform generator (AWG) using a soliton crystal micro-comb source with a free spectral range (FSR) of 48.9 GHz. The comb source provides over 80 wavelengths, or channels, that we use to successfully achieve arbitrary waveform shapes including square waveforms with a tunable duty ratio ranging from 10% to 90%, sawtooth waveforms with a tunable slope ratio of 0.2 to 1, and a symmetric concave quadratic chirp waveform with an instantaneous frequency of sub GHz. We achieve good agreement between theory and experiment, validating the effectiveness of this approach towards realizing high-performance, broad bandwidth, nearly user-defined RF waveform generation.

Synchrotron radiation computed tomography (SRCT) allows more accurate calcified plaque and coronary stenosis assessment as a result of its superior spatial resolution, however, typical micro-computed tomography (micro-CT) systems have even higher resolution. The purpose of this study was to compare performance of high-resolution micro-CT with SRCT in the assessment of calcified plaques and a previously published dataset of coronary stenosis assessment. This experimental study involved micro-CT scanning of three-dimensional printed coronary artery models with calcification in situ used in our previously published SRCT study on coronary stenosis assessment. Measurements of coronary stenosis utilizing both modalities were compared using a paired sample t-test. The degrees of stenosis measured on all but one micro-CT dataset were statistically significantly lower than the corresponding SRCT measurements reported in our previous paper (p&lt;0.0005-0.05). This indicates that the superior spatial resolution of micro-CT was able to further reduce over-estimation of stenosis caused by extensive calcification of coronary arteries and hence false positive results. This study shows that high-resolution micro-CT outperforms SRCT in both calcified plaque and coronary stenosis assessment. This finding will become clinically important for cardiovascular event prediction and enable reclassification of individuals with low and intermediate risk into appropriate risk categories when the technical challenges of micro-CT in clinical practice such as the small field of view and demanding on image processing power are addressed.

Pregnancy at advanced maternal age (AMA) is a condition of potential risk for the development of maternal-fetal complications with possible repercussions even in the long-term. Here, we analyzed the changes of plasma redox balance and the effects of plasma on human umbilical cord mesenchymal cells (hUMSCs) in AMA pregnant women (patients) at various timing of pregnancy. One hundred patients and twenty pregnant women younger than 40 years (controls) were recruited, and evaluated at various timings during pregnancy until after delivery. Plasma samples were used to measure the thiobarbituric acid reactive substances (TBARS), glutathione and nitric oxide (NO). In addition, plasma was used to stimulate the hUMSCs, which were tested for cell viability, reactive oxygen species (ROS) and NO release. The obtained results showed that throughout pregnancy until after delivery in patients the levels of plasma glutathione and NO were lower than those of controls, while those of TBARS were higher. Moreover, plasma of patients reduced cell viability and NO release, and increased ROS release in hUMSCs. Our results highlighted alterations in the redox balance and the presence of potentially harmful circulating factors in plasma of patients They could have clinical relevance for the prevention of complications related to AMA pregnancy.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

Androgenetic alopecia is a genetic disorder caused by an excessive response to androgens. This alopecia is the most common cause of progressive hair loss in men and causes low self-esteem in patients. In this study we used various methods, including quantitative PCR, flow cytometry, ELISA, and immunocytochemistry, to evaluate the biological effects of germinated hemp seeds extract and exosomes derived from calli of germinated hemp seeds. This research reveals pre-ventive functions of two biomaterials (GE2000: 2000 ug/mL germinated hemp seeds extract; E40: 40 ng/mL exosomes derived from calli of germinated hemp seeds) for androgenetic alopecia through three biochemical categories: genetic modulation in hair follicle dermal papilla stem cells (HFDPSCs), cellular differentiation, and modulation of immune systems. Despite exposure to dihydrotestosterone (DT), two materials upregulated alopecia preventing genes including Wnt, β-catenin, and TCF in HFDPSCs. Conversely, alopecia activating genes (STAT1, 5α-reductase type 1, and IL-15R) were suppressed. Moreover, two materials suppressed alopecia genes (NKG2DL, IL2-Rβ, JAK1, and STAT1) in CD8+ T cells. Notably, E40 was effected more in-tensely in these biochemical categories than those of GE2000. Consequently, E40 and GE2000 ef-fectively prevented DT stress. Additionally, two materials activated mechanisms for hair for-mation through the biological activities of three categories.

Adult stem cells (ASCs) can be cultured with difficulty from most tissues, often requiring chemical or transgenic modification to achieve adequate quantities. We show here that mouse primary fibroblasts grown in suspension change from the elongated and flattened morphology observed under standard adherent culture conditions generating rounded cells with large nuclei and scant cytoplasm expressing the mesenchymal stem cell (MSC) marker (Sca1; Ly6A) within 24hrs. Based on this initial observation, we describe here a suspension culture method that, irrespective of the lineage used, mouse fibroblast, primary human somatic cells (fibroblasts, hepatocytes and keratinocytes), is capable of generating a high yield of cells in spheroid form which display expression of ASCs surface markers, circumventing the anoikis which often occurs at this stage. Moreover, mouse fibroblasts-derived spheroids can be differentiated into adipogenic and osteogenic lineages. Analysis of single cell RNA sequence data identified 8 distinct cell clusters with one in particular comprising approximately 10% of the cells showing high levels of proliferative capacity expressing high levels of genes related to MSCs and self-renewal as well as extracellular matrix (ECM). We believe the rapid, high-yield generation of proliferative, multi-potent ASC-like cells by the process we term suspension-induced stem cell transition (SIST) could have significant implications for regenerative medicine.

Among the many Lysosomal Storage Disorders (LSDs) that would benefit from the establish-ment of novel cell models, either patient-derived or genetically engineered, is Mucopolysaccha-ridosis type II (MPS II). In fact, even though a specific therapeutic approach does exist for this disorder (Enzyme Replacement Therapy, ERT, with recombinant human IDS) and haematopoiet-ic stem cell transplantation (HSCT) may also hold promise whenever the disorder is diagnosed soon enough, both approaches have their own drawbacks. Here we present our results on the establishment and characterization of two MPS II pa-tient-derived stem cell line(s) from deciduous baby teeth. To the best of our knowledge, this is the first time a stem cell population is isolated from LSD patient samples obtained from the oral cavity. Taking into account our results on the molecular and biochemical characterization of those cells and our first insights on their subcellular MPS phenotype, we consider these cells will be a valuable tool for both pathophysiological assessments and drugs screenings. Ultimately, we believe patient-derived dental pulp stem cells (DPSC) may represent a feasible alternative to induced pluripotent stem cells (iPSC) in many labs with standard cell culture con-ditions and limited (human and economic) resources.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

This article develops algorithms for the characterization and the visualization of micro-scale features by using a small number of sample points, and with a goal to mitigate for the measurement shortcomings which are often destructive or time consuming. We implement the algorithms to rapidly examine the microscopic features of a Microelectromechanical System (MEMS) surface. Such images are highly dense; therefore, traditional image processing techniques might be computationally expensive. The contribution of this research include first, we develop local and global algorithm based on modified Thin Plate Spline (TPS) model to reconstruct high resolution images of the micro-surface’s topography, and its derivatives by using low resolution images. Second, we obtain a bending energy algorithm from our modified TPS model, and use it to filter out image defects. Finally, we develop a computationally efficient Windowing technique, which combines TPS and Linear Sequential Estimation (LSE), to enhance the visualization of images. The Windowing technique allows rapid image reconstruction based on the reduction of inverse problem.

Brain stem cells (neural stem cells or NSCs) and neurons of a chosen kind reprogramming is a potential technique for cell therapy. It is possible to reprogram non-neuronal cells, for example, by using a predetermined group of factors, nuclear transfer, and the induced transcriptional factors (TFs) expression in a related lineage of cells, and non-coding microRNAs (miRNAs). Researchers have additionally been attempting to improve reprogramming methods, whether it is by employing unique sets of biomolecules and particular TFs or by delivering relevant miRNA and Biomolecules. The technique of miRNA mediated is intriguing for its capability to quickly create a range of biologically desirable cell types for therapy from different lineages of cells. Current findings have made significant advancements towards changing the somatic cells to diverse particular neuronal subgroups with greater efficiency, using reprogramming of miRNA-mediated neural cells, despite the fact that the precise processes need to be discovered. To further understand how miRNAs might direct somatic cells to become neural, we need to look at the latest research on their function in neural reprogramming over the differentiated cells. Recent findings on the role of miRNAs in the initiation of cell reprogramming and the determination of the neuronal subtype's destiny are the primary focus of this comprehensive overview. Furthermore, we cover the far more latest results concerning certain miRNAs' activity in controlling different phases of neuronal differentiation, which contributes in comprehending the interaction network of miRNAs and their receptors.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

Micro-gyroscopes based on the Coriolis principle are widely employed in inertial navigation, motion control, and vibration analysis applications. This paper presents our main contributions which include a novel dual-frame optomechanical gyroscope, a unique photonic crystal cavity design, and advanced numerical simulation and optimization methods. The proposed design utilizes an optical cavity formed between dual oscillating frames, whereby input rotation induces a measurable phase shift via optomechanical coupling. Actuation of the frames is achieved electrostatically via an interdigitated comb-drive design. Through theoretical modeling based on cavity optomechanics and finite element simulation, the operating principle and performance parameters are evaluated in detail. Results indicate an expected angular rate sensitivity of 22.8 mV/°/s and angle random walk of 7.1×10-5 °/h1/2, representing superior precision than to existing micro-electromechanical systems gyroscopes of comparable scale. Detailed analysis of the optomechanical transduction mechanism suggests this dual-frame approach could enable angular vibration detection with resolution exceeding state-of-the-art solutions.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

The present overview of spin-dependent phenomena in nonmagnetic semiconductor microparticles (MPs) and nanoparticles (NPs) with interacting nuclear and electron spins is aimed at covering a gap between the basic properties of spin behavior in solid-state systems and a tremendous growth of the experimental results on biomedical applications of those particles. The first part of the review represents modern achievements of spin-dependent phenomena in the bulk semiconductors from the theory of optical spin orientation under indirect optical injection of carriers and spins in the bulk crystalline silicon (c-Si) – via numerous insightful findings in the realm of characterization and control through the spin polarization – to the design and verification of nuclear spin hyperpolarization in semiconductor MPs and NPs for magnetic resonance imaging (MRI) diagnostics. The second part of the review is focused on the electron spin-dependent phenomena in Si-based nanostructures, including the photosensitized generation of singlet oxygen in porous Si and design of Si NPs with unpaired electron spins as prospective contrast agents in MRI. The experimental results are analyzed by considering both the quantum mechanical approach and several phenomenological models for the spin behavior in semiconductor/molecular systems. Advancements and perspectives of the biomedical applications of spin-dependent properties of Si NPs for diagnostics and therapy of cancer are discussed.

Many research work has demonstrated that taken the Combined Cooling Heating and Power system (CCHP) as the core equipment, the integrated energy system (IES) can bring obvious benefit to energy efficiency, CO2 emission reduction and operation economy in urban areas. Compared with isolated IES, integrated energy micro-grid (IEMG) which is formed by connecting multiple regions IES together, through distribution and thermal network, can further improve the reliability, flexibility, cleanliness and economy of regional energy supply. Based on the existing IES model, this paper describes the basic structure of IEMG and built a IEMG planning model. The planning based on the mixed integer linear programming, and economically construction planning scheme are calculated by using known electricity, heating and cooling loads information and the given multiple equipment selection schemes. At last, the model is validated by a case study. The results show that the application of IEMG can effectively improve the economy of regional energy supply.

In the fifth generation communication system, millimeter wave (mmWave) networks will coexist with traditional micro wave (μWave) networks, which allows for higher data transmission rate and better user experience. In this paper, we give a comprehensive framework of mathematical models and analytical methods for multi-tier mmWave and μWave hybrid caching networks based on stochastic geometry. We propose an association strategy by assuming average biased-received power association and Rayleigh fading. Accordingly, by using a D-ball approximating blockage model of mmWave networks, expressions of the cell association probability and the coverage probability of the hybrid networks are derived. Also, we use the average successful delivery probability as the performance metric to analyze the existing caching placement strategies. Simulation results validate the accuracy of our analytical conclusions.

The European mink (Mustela lutreola) is one of Europe's most endangered species, and it is on the brink of extinction in the Iberian Peninsula. The species' precarious situation requires the application of new ex-situ conservation methodologies that complement the existing ex-situ and in-situ conservation measures. Here, we report for the first time the establishment of a biobank of European mink mesenchymal stem cells (emMSC) and oocytes from specimens found dead in the Iberian Peninsula, either free or in captivity. New emMSC lines were isolated from different tissues: bone marrow (emBM-MSC), oral mucosa (emOM-MSc), dermal skin (emDS-MSC), oviduct (emO-MSc), endometrium (emE-MSC), testicular (emT-MSC), and adipose tissue from two different adipose depots: subcutaneous (emSCA-MSC) and ovarian (emOA-MSC). All the eight emMSC lines showed plastic adhesion, detectable expression of characteristic markers of MSCs and, when cultured under osteogenic and adipogenic conditions, differentiation capacity to these lineages. Additionally, we were able to keep 227 Cumulus-oocyte complexes (COCs) in the biobank, 97 of which are grade I or II. The European mink MSC and oocyte biobank will allow for the conservation of the species' genetic variability, the application of assisted reproduction techniques, and the development of in vitro models for studying the molecular mechanisms of infectious diseases that threaten the species' precarious situation.

Pneumonia remains a major cause of morbidity and mortality worldwide, especially during COVID-19 pandemic. With the significant global health burden that pneumonia poses, it is es-sential to improve therapeutic and management strategies. The increasing emergence of antibiotic resistant bacterial strains limits options for effective antibiotic use. New antibiotics for treatment of pneumonia may address deficits in current antimicrobial drugs, with an ability to cover both typical, atypical, and resistance pathogen. Several of these newer drugs also have structural characteristics that allow for a decreased propensity in development of bacterial resistance. Po-tential use of stem cell therapies in place of corticosteroid treatments may also offer an im-provement in patient outcomes. Human mesenchymal stem cell treatments have shown efficacy and safety in treating COVID-19 induced pneumonia. Combined treatment with both stem cells and antibiotics in pneumonia in a rabbit model has also shown significantly increased efficacy in comparison to antibiotic treatment alone, presenting yet another possible route for a novel strategy in treating pneumonia, though additional future studies are necessary before clinical implementation. While pneumonia remains a major disease of concern, having newer approved antibiotics as well as novel therapies such as stem cell treatments in the pipeline offers clinicians more options in effectively treating pneumonia.

Cancer stem cell (CSC) has paved the way to many fundamental and translational studies. Recent studies have highlighted differentiated breast cancer cells (non-CSCs) switching phenotype to CSCs in response to various stimuli, depicting the existence of cancer stem cell plasticity. Although strategies to reduce the phenotypic plasticity of non-CSCs into CSCs are likely to prevent treatment-resilient cancer cells driving recurrence, most phenotypic plasticity mechanisms involve Notch, Wnt or MAPK signaling pathways. In this study, breast cancer cells were irradiated to identify soluble reprogramming factors. Using conditioned medias, protein arrays analyses, flow cytometry and in cellulo/in vivo functional assays, we demonstrated, for the first time, that radiation-induced chemokine expression, especially CXCL1 and CCL5 and their receptors CXCR2, CCR1 and CCR5, stimulates reprogramming of breast non-CSCs into CSCs. Treatment of non-CSCs with recombinant CXCL1 and CCL5 is sufficient to induce cell reprogramming, while their inhibition can be used to prevent reprogramming and sensitize tumor to radiation. Moreover, analysis of gene expression profiles from 38 public merged databases demonstrated that combined over-expression of CXCL1/CXCR2, CCL5/CCR1 or CCL5/CCR5 has a poorer prognosis in patients treated with radiotherapy, suggesting a promising way for patient stratification, where individuals with elevated cytokine levels could benefit from radiotherapy in conjunction with cytokine inhibitors. Taken together, our findings provide a rationale to consider these axes as potential targets and predictive biomarkers in breast cancer patients.

The therapeutic, attenuative, and morphological effects of proprietary neural stem cell-derived extracellular vesicles (NSC EVs, AB126) produced by Aruna Bio, Inc. were assessed in a range of in vitro and in vivo models of stroke. We emphasize that modulation of neuroinflammation is a key target and suggest further studies to advance our understanding of the mechanisms of action and ultimately how best to dose and monitor the benefits of AB126 in stroke patients.

Despite notable advancements in immunotherapy in the past decades, allogeneic hematopoietic stem cell transplantation (allo-HCT) remains a promising, potentially curative treatment modality. Only a limited number of studies has performed a direct comparison of two prevalent rabbit anti-thymocyte globulin (r-ATG) formulations — specifically, Thymoglobuline (ATG-T, formerly Genzyme) and Grafalon (ATG-G, formerly Fresenius). The primary objective of our retrospective analysis was to compare the outcomes of adult patients undergoing matched or mismatched unrelated donor (MUD/MMUD) allo-HCT, with a graft-versus-host disease (GvHD) prophylaxis based on either ATG-T or ATG-G. A total of 87 patients undergone allo-HCT between 2012 and 2022 were included. We observed no significant differences between ATG-T and ATG-G concerning the occurrence of acute graft-versus-host disease (aGvHD), regardless of its severity. Conversely, chronic graft-versus-host disease (cGvHD) occurred less frequently in the ATG-T group compared to ATG-G (7.5% vs. 38.3%, p=0.001). Patients treated with ATG-T manifested a higher incidence of cytomegalovirus (CMV) reactivations (70% vs. 31.9%, p&lt;0.001), with a shorter time between transplant and CMV (&lt;61 days, 77.8% vs. 33.3%, p=0.008) and a higher median CMV copy number (1000 vs. 0, p=0.004). Notably, despite a higher occurrence of CMV reactivations in the ATG-T cohort, most patients were asymptomatic compared to ATG-G (85.7% vs. 43.8%, p=0.005). Finally, we observed no significant differences in terms of 5-year overall survival (OS) and 3-year probability of relapse while comparing ATG-T and ATG-G (32.0% vs 40.3%, p=0.423; 63.9% vs 55.7%, p=0.438, respectively).

Modeling the flow of polymer solutions requires knowledge at various length and time scales. The macroscopic behavior is described by the overall velocity, pressure and stress. The polymeric contribution to the stress requires knowledge of the evolution of polymer chains. In this work, we use a microscopic model, the finitely extensible nonlinear elastic (FENE) model, to capture the polymer behavior. The benefit of microscopic models is they remain faithful to the polymer dynamics without information loss via averaging. The downside is the computational cost needed to solve the thousands to millions of differential equations describing the microstructure. We thus describe a multiscale flow solver that utilizes GPUs for massively parallel, efficient simulations. We compare and contrast the microscopic model with its macroscopic counterpart under various flow conditions. In particular, significant differences are observed under nonlinear flow conditions, where the polymers become highly stretched and oriented.

The increased interest in space activities, structural health monitoring, and terrestrial monitoring in hostile and inaccessible zones places a high demand for energy sources for autonomous systems. Conventional electrochemical batteries that could be used are plagued by low energy storage density, short life, disposal of unwanted batteries, and related undesired recharging or replacement maintenance requirements, which endangers the environment. Fuel cells and solar energy sources being exploited to mitigate the adverse effect of environmental threats posed by batteries and fossil fuels are costly to acquire and maintain. The availability of energy sources derived from waste heat from radioactive decay for domestic appliances and industrial equipment will also help alleviate the effects of climate change, which continues to threaten the environment due to fossil fuel energy-based sources that emit harmful carbon monoxide into the atmosphere. A combination of energy from waste heat, harvested via thermoelectricity and existing battery technology to produce a hybrid energy source, can guarantee secured energy for an extended period. Based on the Seebeck effect, thermoelectric energy generation may considerably contribute to sustainable energy development and meet the power demand for spacecraft applications. Modeling of the energy from waste heat, the Li-ion battery, and a hybrid energy source are considered, and their performances are established using the MATLAB/Simulink environment. Results confirmed the comparative advantage of the hybrid energy source over and above the respective electrochemical batteries and waste heat energy sources regarding effectiveness and performance efficiency. Since batteries are required to operate in a constantly changing environment, the effects of temperatures on batteries were investigated. The results show that the performances of batteries decrease with a decrease in ambient temperature and that the higher the maximum operating capacity, the higher the battery's internal temperature.