A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

In order to improve the stiffness of the flexible robot,this paper proposes a variable-stiffness elastic actuator to improve the rigidity of flexible robots. The actuator integrates the working principles of a pneumatic drive, wedge structure, and particle blockage. the tensile stiffness of the actuator is nonlinearly negatively correlated with the air pressure because of the structural and material properties.The compressive stiffness and lateral stiffness increases nonlinearly as air pressure increases, being 3and 121 times greater at 0.17 MPa compared to 0 MPa, respectively. Beyond 0.17 MPa, the two stiffness of the actuator experiences incremental growth due to wedge impedance forces.

Mechanical properties of tumor cytoskeleton are extremely vital for any phases of cancer, especially in tumor invasion and metastasis. However, in current category of anticancer drugs, the cytoskeleton-targeting drugs are limited and its role in tumor progression is unclear. Here, we present the mechanical characteristics of tumor stiffness are tightly regulated by cancer cytoskeleton including actin filaments and microtubule during tumor initiation, growth and metastasis, and review the natural drugs that target cancer cytoskeleton. We define cytoskeleton dynamics as target mechanisms for anticancer drug, and summary the plant, microbial and marine sources of natural products. Furthermore, the material approaches to active cancer mechanics are supplied in this review. We aim to promote the development of anticancer drugs that target tumor mechanics by using those material approaches in future and find its pharmacological application.

this paper focuses on a scientific study of the restoration, rehabilitation and reuse of the great throne hall, the most important hall in al-jawhara palace. it also aims to study the most important factors and forces of damage that affected the great throne hall, natural, biological, and human, and the resulting damage. field tests were performed, laboratory tests to determine fracture stress, liquidity and spandex limits tests, chemical analysis on soil samples and geoelectrical testing of the soil, and the results did not show caves or voids in the ground until a depth of 10.00 m, construc-tion materials were studied and tested using x-ray, (xrd), mechanical tests (tensile, shear, com-pression), and a study of the effect of seismic loads on the walls; the results showed horizontal and vertical cracks; based on the study and analysis of these cracks, it was possible to present modern techniques in restoration and reinforcement methods, and in conclusion, the researcher's recommendations.

Offshore Wind Turbines (OWT) with increasingly higher energy output are being developed to meet energy demand, posing challenges for their foundation design. Several foundation types are used to support these turbines with monopiles (MP) accounting for 80% of the installed capacity. In this study, three-dimensional (3D) nonlinear finite element models (FEM) were employed to investigate the behaviour of monopile foundation supporting a 5MW wind turbine when subjected to lateral loading. Results indicate that the MP behavior depending on the pile length to diameter (L/D) ratio and the soil shear strength. Inspection of bending moment profiles at the lateral ultimate capacity indicated the monopiles can behave in flexible manner even with low L/D ratio. The L/D ratio affected the MP normalized lateral ultimate capacity at varying degrees and the biggest effect was for soft clays, amounting to around 5 folds increase for L/D values of 3.33 to 13.33. Lesser effects were found for stiff clays.

Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

Cells actively sense differences in topology, matrix elasticity and protein composition of the extracellular microenvironment and adapt their function and morphology. In this study, we focus on the cross-talk between matrix stiffness and protein coating density that regulate morphology and proliferation dynamics of single myocytes. For this, C2C12 myocytes were monitored on L-DOPA functionalized hydrogels of 22 different elasticity and fibronectin density compositions. Static images were recorded and statistically analyzed to determine morphological differences and to identify the optimized extracellular matrix (ECM). Using that information, selected ECMs were used to study the dynamics before and after cell proliferation by statistical comparison of distinct cell states. We observed a fibronectin density independent increase of the projected cell area until 12 kPa. Additionally, changes in the fibronectin density led to an area optimum at about 2.6 μg/cm, which was confirmed by an independent F-actin analysis, revealing a maximum actin filament to cell area ratio of 7.5 %. The proliferation evaluation showed an opposite correlation between cell spreading duration and speed to the matrix elasticity and protein density, which did not affect the cell cycle duration. In summary, we identified an optimized ECM composition, while independent matrix properties regulate distinct cell characteristics.

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals like magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For WE43 scaffolds, during the first days an increase of the smeared Young's modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the struts surfaces. In this study the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite element simulations are performed to study the influence of the substrate layer thickness and Young's modulus for single struts and for a new scaffold geometry with adapted polar f2cc,z unit cells. The finite element model is further validated by compression tests on AM scaffolds made from Zn1Mg. The results show, that even low thicknesses and Young's moduli of the substrate layer increases significantly the smeared Young's modulus under axial compression.

An analysis of the stiffness theory reveals that coal mass compression bumps occur only when both the failure criterion and the stiffness criterion are simultaneously satisfied. Then a new structural factor called uneven stiffness coal seam structure (USCS) is proposed, which consists of an uneven stiffness coal seam along with continuous roof and floor. The USCS serves the dual functions of pressure concentration and stiffness reduction. The former facilitates stress concentration from the low stiffness zone (LSZ) to the high stiffness zone (HSZ), thus raising the risk (rF) of failure. The latter reduces the stiffness of the surrounding rock of the HSZ, allowing the system to meet the stiffness criterion even with a hard roof, thereby reconciling the contradiction between the stiffness theory and engineering experience and raising the risk (rI) of instability. The HSZ of the USCS, including thinning zones, bifurcating areas, magmatic intrusion areas, and remnant pillar affected areas, is more susceptible to coal bump incidents than a conventional coal seam. Mechanical analysis and simple numerical simulations validate the pressure concentration and stiffness reduction functions of the USCS. The results demonstrate the following: 1) The normal stress of the HSZ positively correlates with ER, HR, KH, and SL, but negatively correlates with KL and SH; The stiffness of surrounding rock of the HSZ negatively correlates with HR, KH, SL, and SH, but positively correlates with ER and KL. 2) Failures within the HSZ of the USCS enables the roof strata to release bending deformation energy without undergoing fracturing. 3) The alignment between the HSZ of an existing USCS and the HSZ of an artificial USCS advancing with the working face intensifies stress concentration and reduces stiffness, thereby significantly increases the risk (rCB) of coal bump. By applying the stiffness theory and relevant USCS findings, new explanations can be provided for engineering phenomena such as the time-delayed coal bumps, the inefficient pressure relief in ultra thick coal seams, and the “microseism deficiency” observed prior to certain coal bumps.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

The use of haptic devices in rehabilitation of impaired limbs has become rather popular, given the proven effectiveness in promoting recovery. In a standard framework, such devices are used in rehabilitation centers, where patients interact with virtual tasks, presented on a screen. To track their sessions, kinematic/dynamic parameters or performance scores are recorded. However, as Internet access is now available at almost every home, and in order to reduce the hospitalization time of the patient, the idea of doing rehabilitation at home is gaining wide consent. Medical care programs can be synchronized with the home rehabilitation device; patient data can be sent to the central server that could redirect to the therapist laptop (tele-healthcare). The controversial issue is that the recorded data do not actually represent the clinical conditions of the patients according to the medical assessment scales, forcing them to frequently undergo clinical tests at the hospital. To respond to this demand, we propose the use of a bilateral master/slave haptic system that could allow the clinician, who interacts with the master, to assess remotely and in real time the clinical conditions of the patient that uses the home rehabilitation device as the slave. In this paper, we describe a proof of concept to highlight the main issues of such an application, limited to one degree of freedom, and to the measure of the stiffness and range of motion of the hand.

In recent times, the soft robotics field is gaining numerous research focus owing to its high level of manipulation capabilities unlike traditional rigid robots, which gives room for an increasing use in other areas. However, compared to traditional rigid gripper robots, being capable of controlling/obtaining overall body stiffness when required is yet to be further explored since soft gripper robots have inherently less rigid properties. unlike previous designs with very complex variable stiffness systems, this paper demonstrates a soft gripper design with minimum system complexity while being capable of varying the stiffness of a continuum soft robotic actuator and proves to have potential applications in gripping objects of various shapes, weights & sizes. The soft gripper actuator comprises two separate mechanisms; the pneumatic mechanism for bending control and the mechanical structure for stiffness variation by pulling tendons using stepper motors which compresses the actuator, thereby changing the overall stiffness. The pneumatic mechanism was first fabricated and then embedded into another silicon layer during which it was as well merged with the mechanical structure for stiffness control. By first pneumatically actuating the actuator which causes bending and then pulling the tendons, we found out that the actuator stiffness value can be increased up to 145 % its initial value, and the gripper can grasp & lift a weight of up to 2.075 kg.

In this paper, a modular wire-actuated robotic arm was designed to improve the safety and adaptability of service robots during human-robot interaction. To raise the stiffness adjustment range of the robotic arm, a symmetric variable-stiffness unit was designed based on flexure, which had compact and simple structure, and lowly nonlinear stiffness-force relationship. In this paper, we focused on the research of the symmetric 1-DOF joint module. Based on the kinematics and stiffness analysis, the pose of the joint module could be adjusted by controlling the length of the wires, and the stiffness of the joint module could be adjusted by controlling the tension of the wires. Because of the actuation redundancy, the pose and stiffness of the joint module could be controlled synchronously. Furthermore, a directly method was proposed for the stiffness-oriented wire tension distribution problem of the 1-DOF joint module. A simulation was carried out to verify the proposed method.

The development of straddle-type monorail tour-transit systems (MTTSs) has received keen attention, raising the need for revisions on related design codes. This work presents a comprehensive assessment of the lateral stiffness limit of steel substructures in MTTSs. Firstly, a wind‒vehicle‒bridge coupling model was established, integrating multibody dynamics and finite element methods. This model was then validated against field test results, considering measured track irregularities as the excitation. Afterwards, a trend analysis and a variance-based sensitivity analysis was performed to investigate the effect of various factors on the dynamic response of MTTS. Referring to existing specifications, an evaluation index for the lateral stiffness of pier columns and track beams was proposed. Results indicate that the pier height significantly impacts the lateral displacement of the pier top, accounting for 87% of the first-order sensitivity index and 75% of the total sensitivity index. In comparison, the lateral stiffness of track beams contributes over 70% to the maximum lateral acceleration and displacement at the mid-span. Finally, the lateral limited values for the displacement at the pier top and the deflection–span ratio of the track beam were determined as 8.04 mm and L/4200, respectively. These findings can serve as valuable references for future research and designs in this field.

AFM nanoindentation showed variation in stiffness (Elastic modulus) due to heterogenous nature of the collagen fibres. The S values varied from 5 N/m to 11.11 n/m corresponding to an E change of 2.25 to 1.38 GPa. The variation in effective modulus (Eff) with respect to displacement indicated crossing the parabolic limit. A softening index n was proposed due to the heterogenous behaviour of the biomaterials

As a new type of gear, bevoloid gears have the advantages of compensating axial error, smooth transmission, and eliminating turning error, and they are widely used in applications requiring high transmission accuracy and stability. However, research on calculating the time-varying mesh stiffness of bevoloid gears is still limited, and there is an urgent need to propose a method that can calculate the stiffness of bevoloid gears quickly and accurately. This paper first establishes the bevoloid gear tooth profile expressions, then assumes a pair of bevoloid gears meshing with the same rack and derives the contact line equations of parallel axis bevoloid gear pairs, and analyze the contact process of bevoloid gears. We propose an analytical algorithm that uses the slicing method to calculate the stiffness of helical gears, straight bevoloid gears, and helical bevoloid gears, change the parameters of helical bevoloid gears respectively, and analyze the influence of different parameters on stiffness. Finally, the finite element method is used to verify the analytical method, and the correctness of the analytical calculation results is verified, and the errors are analyzed.

In the laboratory practice, several standards for testing the bending stiffness of corrugated board are used. There are often cases of tests where the results depend on the way the sample is placed on the supports. The problem arises when the board is five-ply (with two corrugated layers with different corrugation heights) or when the board has asymmetrically selected papers on the flat layers. In this article, we focus our attention on the problem related to boundary conditions, with particular attention to the local effects of the support of the sample. Since the cardboard layers, both flat and corrugated, have a small thickness, a slight deformation of the papers can always be observed at the point of contact between the sample and the support, which affects the readings of the measured stiffness. The paper presents theoretical and numerical analyzes showing how much the method of supporting the sample affects the measured bending stiffness of various samples. Numerical observations were also compared with the results of analyzes presented by other scientists as well as with experimental results.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Introduction: Systemic lupus erythematosus (SLE) is an autoimmune disease associated with an increased risk of cardiovascular diseases (CVD), leading to elevated mortality rates among patients. We aimed to evaluate the levels of cardio-ankle vascular index (CAVI), global longitudinal strain (GLS), ventricular-arterial coupling (VAC) and high-sensitivity cardiac troponin (hsTn), in SLE patients and to explore their relationship with clinical parameters. Methods: This cross-sectional study enrolled 82 SLE patients without evident cardiac or kidney impairment and 41 age- and sex matched healthy controls. We comparatively evaluated CAVI, GLS, VAC, and hsTn between SLE patients and controls, and we assessed their association among SLE patients with disease activity based on the SELENA-SLEDAI Activity Index. Multivariate regression analysis was performed to identify independent predictors of CAVI and hsTn within the SLE cohort. Results: In comparison to healthy controls, SLE patients presented with significantly higher CAVI, GLS and hsTn levels, while VAC was significantly reduced (p<0.001). Further, SLE patients with active disease (SELENA-SLEDAI≥4) exhibited higher levels of CAVI and troponin than those with inactive disease (p<0.001). SLEDAI was an independent predictor of CAVI, while VAC and SLEDAI were independent determinants of hsTn in SLE cohort. Conclusion: SLE patients displayed abnormal levels of CAVI, VAC, GLS, and troponin compared to healthy individuals. Our findings implicate the potential of those CV novel CVD risk factors to refine screening and therapeutic strategies for this specific population.

It is necessary to address the scarcity of crushed stones for pavement structural layers. So fly ash can be proved to be promising solution as more than 270 tonnes of fly ash is generated in India. Though, numerous research has been conducted for the use of fly ash intreated and untreated form, high volume of fine particles and brittleness of the stabilized fly ash pose a great problem for its use in subbase and base. Moreover, stiffness or modulus of stabilized fly ash is vital elastic parameter which is used for mechanistic pavement design. Hence, in this study an extensive experimental investigation is carried out to study its strength and stiffness properties such as compressive strength, indirect tensile strength and flexural strength, cyclic indirect tensile modulus and flexural modulus of fiber reinforced cement stabilized fly ash, stone dust, aggregate mixtures. The stone dust and aggregates have been added to enhance the gradation of the composite’s mixture. The study presents the effect of fiber on strength and stiffness properties. The experimental result reveals that addition of polypropylene (PP) fibers up to 0.25 wt.% enhances the compressive strength and any further addition of fiber results in decrease of the strength. However, indirect tensile strength and flexural strength increases with increase in fiber percentage up to 0.5 wt.%. Cement content is observed to be the dominant parameter for stabilized materials. Suitable relationships have been developed between strength and modulus parameters for stabilized mixtures. Based on the strength and stiffness study, 70% fly ash and 30% stone dust-aggregate and 60% fly ash and 40% stone dust-aggregate with 6% cement can be considered for the base layer. Based on the indirect tensile strength and flexural strength behavior, 0.35% is considered as the optimum fiber percentage.

Mannosylerythritol lipids (MELs), one of the most promising biosurfactants (BS), are glycolipids produced by yeasts or fungi, with great environmental performance and a high compatibility with the human body. MELs besides working as typical surfactants, can form diverse structures when in the critical aggregation concentration (CAC), reducing the surface tension of water and other solutions, and being stable over a wide range of conditions. Among others, MELs present anti-microbial, antitumor, antioxidant and anti-inflammatory activity, skin and hair repair capacity, which opens possibilities for their use in applications from cosmetics and pharmaceutics to bio-remediation and agriculture. However, their market share is still low when compared to other glycolipids, due to their less developed production process and higher production cost. This re-view gathers information on the potential applications of MELs mentioned on the literature since 1993. Furthermore, it is also explored the current strategies being developed to enhance the market presence of MELs, in parallel with the ones developed for rhamnolipids and sophorolipids.

Antioxidants reduce arterial stiffness but the effects previously reported are weak. The present study evaluated the effects of 2 weeks of therapy with a combination of antioxidants (l-cysteine, thiamine, pyridoxine and ascorbic acid) compared to placebo on stiffness index (SI) a measure of arterial stiffness that is strongly correlated with central pulse wave velocity (PWV), using a Pulse Trace recorder in a diverse group of 78 volunteers. SI fell by 1.7 m/sec relative to placebo (95% confidence intervals 0.6 to 2.7 m/sec), a reduction of 19% (95% confidence intervals 9% to 31%). The Glass effect size was 1.4, indicating a very strong treatment effect which was substantially greater than found in previous studies of the effects of antioxidant therapy on arterial stiffness. The magnitude of reduction in SI was positively correlated with increasing age (r = 0.362 P = 0.02). The change in RI, a measure of compliance of small to medium size arteries, did not differ between the antioxidant and placebo groups The combination of antioxidants studied reduced PWV to a much greater extent than reported for other antioxidants. This combination may be of value in the treatment of cardiovascular disease.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Transition zones are in the places on the track, with a change in the basic composition of the railway body. There are many sections with a sudden change in the stiffness of the structures built. When the trains are running, a longitudinal shock wave is created from the wheels, which hits these building objects with a higher stiffness and deforms the surroundings of these zones. The greatest attention should be paid mainly to the transition points from the fixed track to the classic track with a track bed, including objects of the railway substructure such as bridges, portals of tunnels, etc. As part of the research sections on the main corridor lines, a long-term inspection and monitoring was carried out with a continuous measurement system using the KRAB trolley. Height changes in the deflections of rails are evidence of their behavior. The measurements took place on a fixed track and a track with a ballast. Changes in the height jumps between the fixed railway track and the track with a gravel bed are significant and have been recorded since the tracks were put into operation. These certain height deflections allow designers to develop new, more durable construction designs.

Natural rocks are highly heterogeneous due to various geological processes that constantly alter their properties. The accumulation, deposition, and cementation of mineral and organic particles continuously modify the spatial characteristics of rock properties. Property variability or anisotropy is commonly observed in most rock types and influences strength, transport, and thermal conductivity behavior. This unpredictability presents a significant challenge for laboratory testing. Binder-jet additive manufacturing (3D printing) has emerged as a valuable technology for characterizing rock properties in geoscience and engineering. This study proposes a methodology to evaluate the variability and repeatability of mechanical properties of 3D-printed sandstones during binder-jet additive manufacturing. The mechanical properties were analyzed statistically for samples located in various parts of the 3D printer build volume. The results showed that the 3D-printed sandstones exhibited significant variations in their strength and stiffness properties when measured from samples produced within the same build volume during binder-jet additive manufacturing. The Uniaxial Compressive Strength (UCS) varied from 23 to 38 MPa, with an average value of 29 MPa. The Young's modulus, on the other hand, ranged from 1.5 to 4.05 GPa, with an average value of 2.33 GPa. The variability of the mechanical properties, quantified by the standard deviation, decreased when the entire population of 3D-printed sandstones was divided into smaller samples situated at different elevations of the build platform.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

The purpose of this study was to determine the effects of aerobic exercise on carotid to femoral pulse wave velocity (cf-PWV), cell adhesion molecules (intracellular adhesion molecules (ICAM-1), vascular cell adhesion molecules (VCAM-1), and endothelial selectin (E-selectin), and oxidized-LDL in elderly women aged 70–85 years, and to identify the effect of and correlation with vascular stiffness. Forty participants were recruited and divided into three groups; vascular stiffness (VSG, n=14), obesity (OG, n=14), and normal (NG, n=12). All groups were given a 16-week intervention of aerobic exercise, and the data collected before and after exercise were analyzed using SPSS Ver. 23.0. Two-way repeated-measures ANOVA was used to evaluate between-group and time-dependent interaction effects. One-way ANOVA was used to evaluate between-group variations. In addition, the significance was tested using a post-hoc test (Scheffe). The within-group variations by time before and after exercise were examined using a paired t-test, and correlation analysis was performed using Pearson correlation coefficients. Simple regression analysis was performed for variables showing significant differences. The results indicated interaction effects for cf-PWV (p<.001), VCAM-1 (p<.01), E-selectin (p<.05) and oxidized LDL (p<.001). The rate of change of cf-PWV was positively correlated with that of VCAM-1 (r=.352, p<.05) and that of oxidized-LDL (r=.325, p<.05) with statistical significance. To determine the effect of the rate of change of cf-PWV on the rate of change of VCAM-1, the variables were tested, and the coefficient of determination in the regression analysis was .124, indicating that 12.4% of the tested variables fit the standard regression line. The variables for the effect of the rate of change of cf-PWV on the rate of change of oxidized LDL were also tested, and the coefficient of determination in the regression analysis was .106, indicating that 10.6% of the tested variables fit the standard regression line. Thus, the 16-week regular and consistent aerobic exercise program had significant effects on the cf-PWV, ICAM-1, VCAM-1, E-selectin, and oxidized-LDL in elderly Korean women with vascular stiffness, suggesting improvements in vascular stiffness, based on which the intervention is predicted to contribute to the prevention of vascular dysfunction by lowering the risk of cardiovascular disease due to atherosclerosis, as well as having a positive effect in the prevention of impairment of vascular endothelial cells.

Variable Angle Tow (VAT) laminates offer a promising alternative to classical straight fiber composites in terms of design and performance. However, analyzing these structures can be more complex due to the introduction of new design variables. Carrera's Unified Formulation (CUF) has been successful in previous works for buckling, vibrational, and stress analysis of VAT plates. Typically, one-dimensional (1D) and two-dimensional (2D) CUF models are used, with a linear law describing the fiber orientation variation in the main plane of the structure. The objective of this article is to expand the CUF 2D plate finite elements family to perform free vibration analysis of composite laminated plate structures with curvilinear fibers. The primary contribution is the application of Reissner's Mixed Variational Theorem (RMVT) to a CUF finite element model. The Principle of Virtual Displacements (PVD) and RMVT are both used as variational statements for the study of monolayer and multilayer VAT plates dynamic behavior. The proposed approach is compared to Abaqus three-dimensional (3D) reference solutions, classical theories and literature results to investigate the effectiveness of the developed models. Results demonstrate that mixed theories provide the best approximation of the reference solution in all cases.

In this paper, we have shown the electronic circuit equivalence of a mechanical system consists of two oscillators coupled with each other. The mechanical design has the effects of the magnetic, resistance forces and the spring constant of the system is periodically varying. We have shown that the system’s state variables, such as the displacements and the velocities, under the effects of different forces, lead to some nonlinear behaviors, like a transition from the fixed point attractor to the chaotic attractor through the periodic and quasi-periodic attractors. We have constructed the equivalent electronic circuit of this mechanical system and have verified the numerically obtained behaviors using the electronic circuit.

In this study, nanostructured cerium-doped TiO2 (Ce-TiO2) films with the addition of different amounts of cerium (0.00, 0.08, 0.40, 0.80, 2.40, and 4.10 wt. %) were deposited on a borosilicate glass substrate, by flow coating sol-gel process. After flow coating, deposited films were dried at the temperature of 100 °C for 1 h, followed by calcination at the temperature of 450 °C for 2 h. For the characterization of sol-gel TiO2 films, the following analytic techniques were used: X-ray diffraction (XRD), thermal gravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry (DSC). Sol-gel derived Ce-TiO2 films were used for photocatalytic degrada-tion of the ciprofloxacin (CIP). The influence of the amount of Ce in TiO2 films, the duration of the photocatalytic decomposition, and the irradiation type (UV-A and simulated solar light) on the CIP degradation were monitored. Kinetics parameters (reaction kinetics constants and the half-life) of the CIP degradation, as well as photocatalytic degradation efficiency, were determined. The best photocatalytic activity was achieved by the TiO2 film doped with 0.08 wt.% Ce, under both UV-A, and solar irradiation.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The field of construction materials is pivotal in developing sustainable and resilient infrastructure. This demands continuous research to understand the properties and behaviors of these materials under diverse conditions. Although advancements in material science and numerical modeling have been significant, experimental testing remains indispensable for a thorough comprehension of material characteristics, particularly under extreme stresses and environmental factors. This need has forced the development of a wide array of testing techniques, each designed to evaluate specific engineering properties, thus creating a complex and varied landscape of experimental methodologies. This study provides a comprehensive overview of both conventional and innovative experimental testing techniques used to characterize construction materials. It explores the related methodologies and identifies potential gaps in their application within the industry. The spectrum of testing covered includes mechanical, chemical, thermal, microstructural, durability, physical, rheological properties, and non-destructive testing methods. Mechanical tests assess strength, hardness, and fatigue, whereas chemical analyses utilize techniques such as spectroscopy and chromatography. Thermal properties are examined using thermogravimetric analysis, and microstructural characteristics are explored through advanced imaging techniques. Durability testing focuses on materials’ resistance to environmental challenges, while physical properties tests evaluate aspects like porosity and water absorption. Rheological and non-destructive tests further examine materials’ behavior and integrity without causing damage. By discussing these methodologies, the study sheds light on various approaches to material evaluation and aims to enhance the selection, application, and development of testing standards. This overview seeks to inform and inspire future research and innovation in the science of construction materials, contributing to the development of more resilient and sustainable construction practices.

Improvement of hydrophysical properties and corrosion resistance of self-compacting concrete to the effects of alternate freezing-thawing and aggressive soils of southern and central Kazakhstan is of interest to a wide range of researchers from the side of practical application of the obtained results in construction practice. It is proposed to form a spatially reinforced fine crystalline structure of cement matrix with maximum dense packing by using a complex modifier (Hyperplasticiser + Polymer + Microsilica + Fibro fibers) in the composition of self-compacting concretes (SCC). The introduction of the calculated amount of the above additives increases the operational reliability of the current SCC compositions, increasing the water resistance to W16, frost resistance to F=500, increasing the compressive strength by 20%, reducing the mass loss of samples during corrosion leaching to 50%. It has been experimentally established that the proposed addition of complex modifier (Hyperplasticiser + Polymer + Microsilica + Fiber fibers) to the SCC composition allows obtaining self-compacting concrete of high quality with improved performance characteristics (compressive strength, water resistance, frost resistance and corrosion resistance). Studies have shown that the complex modifier-modified SCC compositions have a high degree of resistance in aggressive environments and leaching corrosion. Based on the results of the conducted tests, it is possible to recommend the obtained SCC compositions for production of building products working in the zone of alternating freezing-thawing and aggressive soils.

Background: Myocardial infarction is increasing at a young age. New tools are needed to evaluate the risk population of young patients. GDF-15 has been implicated in several key mechanisms of atherogenesis and also is associated with increased mortality and cardiovascular events in patients with coronary artery disease. Arterial stiffness parameters, including pulse wave velocity, can also be measured using peripheral arterial tonometry and can indicate the presence or progression of atherosclerotic changes. The aim of this study is to evaluate the GDF-15 level and arterial stiffness parameters in patients with premature myocardial infarction Method: Thirty patients who recovered from a myocardial infarction were consecutively included. Fifteen age-sex-matched subjects were included as controls. The patients’ serum GDF-15 concentration levels were measured using relevant kits. Measurements of arterial stiffness [pulse-wave velocity (PWV) and augmentation index (AIx)] were performed using a Mobil-O-Graph arteriography system. Results: GDF-15 concentration levels were significantly higher in the patients with premature myocardial infarction when compared to controls. PWV and AIx were similar between the groups. GDF-15 level was negatively correlated with high-density cholesterol (HDL) and positively correlated with uric acid levels in all study populations. Conclusions: GDF-15 levels may be a risk factor for patients with premature myocardial infarction. This pilot study may trigger further studies to elucidate the central role of GDF-15 in the pathophysiology of early atherosclerosis in the young population.

The subject of the research is the investigation of the behavior of railway tracks in locations with a significant change in the stiffness of the track. These locations can be designed from various structural elements and their materials, and this mainly results in a height change of the track level during its operation. These transition zones are monitored and expertly examined in order to detect undesirable deformations of the geometrical position of the track caused by the trains running. The transition zones are at the points where the fixed track transitions to the classic track bed, in our case it is their combination with bridge structures, especially at their supports. In Slovakia, under the conditions of the Railways of the Slovak Republic, the issue is topical within the framework of the modernization of trans-European railway corridors. The results of experimental measurements and their analysis will provide relevant data for subsequent research solutions for their new numerical modeling, which will ensure a smooth passage through these points of change without height fluctuations, vibrations, and shocks from the wheels of train sets.

This study presents a platform for ex-vivo detection of cancer nodules, addressing automation of medical diagnoses in surgery and associated histological analyses. The proposed approach takes advantage of the property of cancer to alter the mechanical and acoustical properties of tissues, because of changes in stiffness and density. A force sensor and an ultrasound probe were combined to detect such alterations during force-regulated indentations. To explore the specimens, regardless of their orientation and shape, a scanned area of the test sample was defined using shape recognition applying optical background subtraction to the images captured by a camera. The motorized platform was validated using seven phantom tissues, simulating the mechanical and acoustical properties of ex-vivo diseased tissues, including stiffer nodules that can be encountered in pathological conditions during histological analyses. Results demonstrated the platform’s ability to automatically explore and identify the inclusions in the phantom. Overall, the system was able to correctly identify up to 90.3% of the inclusions by means of stiffness in combination with ultrasound measurements, paving pathway towards robotic palpation during intraoperative examinations.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

Aiming at the problem that soft robots are challenging to take into account both flexibility and bearing capacity, Using the software Pneu-Net driver as the deformation mode, magnetorheological fluid material phase transformation to achieve variable stiffness, A pneumatic modular soft joint structure with dynamically adjustable deformation and stiffness in all directions is proposed. In this paper, mathematical models of deformation and variable stiffness are established. The correspondence between gas pressure and deformation and applied current and joint stiffness is obtained. The finite element analysis method was used to simulate the deformation characteristics and variable stiffness characteristics of modular joints based on the Yeoh model. Finally, the theoretical and simulation results are verified by deformation and variable stiffness tests. It is proved that the modular joint has good rigid-flexible coupling characteristics.

Abstract. Results of research into four-membered phosphorus(V)-heterocycles, 2-halogen-1,2λ⁵-oxaphosphetanes are presented. The preparation of 2-halo-1,2λ⁵-oxaphosphetanes by reaction of P-haloylides with carbonyl compounds is described. The mechanism of asynchronous [2+2]-сycloaddition of ylides to aldehydes was proposed on the base of low-temperature NMR investigations. 2-Halogen-1,2λ⁵-oxaphosphetanes were isolated as individual compounds and their structures were confirmed by ¹Н, ¹³C, ¹⁹F and ³¹Р NMR spectra. These compounds are convenient reagents for preparing of various organic and organophosphorus compounds hardly available by other methods. Chemical and physical properties of the 2-halo-1,2λ⁵-oxaphosphetanes are reviewed. The 2-chloro-1,2λ⁵-oxaphosphetanes depending on substituents at the α-carbon atom rearrange with formation of 2-chloroalkylphosphonates or convert into trans-phosphorylated alkenes. Prospective synthetic applications of 2-halo-1,2λ⁵-oxaphosphetanes are analyzed. The 2-halo-1,2λ⁵-oxaphosphetanes may be easily converted to various alkenylphosphonates: allyl- or vinylphosphonates, phosphorus ketenes, thioketenes, ketenimines.

Artificial intelligence (AI) is revolutionizing the textile industry by improving the prediction of fabric properties and handfeel, which are essential for assessing textile quality and performance. However, the practical application and translation of AI-predicted results into real-world textile production remain unclear, posing challenges for widespread adoption. This paper systematically reviews AI-driven techniques for predicting these characteristics by focusing on model mechanisms, dataset diversity, and prediction accuracy. Among 811 papers initially identified, 26 were selected for in-depth analysis through both bibliometric and content analysis. The review categorizes and evaluates various AI approaches, including machine learning, deep learning, and hybrid models, across different types of fabric. Despite significant advances, challenges remain, such as ensuring model generalization and managing complex fabric behavior. Future research should focus on developing more robust models, integrating sustainability, and refining feature extraction techniques. This review highlights the critical gaps in the literature and provides practical insights to enhance AI-driven prediction of fabric properties, thus guiding future textile innovations.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of &gt; 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

Sesamum indicum is considered an underutilized oil-bearing seed in the semi-arid regions of Ghana. Nonetheless, it is a promising source of food with both nutritional and therapeutic benefits. The aim of the present study was to evaluate the antioxidant properties S. indicum seeds using different extraction solvents. The seeds were obtained from the local farmers and prepared for analysis. The bioactive compounds present in the seeds were extracted using hexane, ethyl acetate, ethanol and water and their yields quantified. Total phenolic content (TPC), Condensed tannin content (TTC) and Total antioxidant capacity (TAC) , and DPPH radical scaveging assay were analyzed using standard methods. Antinutrients such as saponins, alkaloids, phytates and oxalates were also analyzed from the powdered seeds. Two chemometric methods; hierarchical cluster analysis (HCA) and Pearson correlation were employed to evaluate the interdependence of the various parameters to result in their antioxidant properties. The re-sults revealed that the solvents utilized had a significant impact on the extraction yield, phyto-chemical component concentration, and antioxidant activities. Hexane extracts of S. indicum seeds significantly exhibited the highest antioxidant activity (p &lt; 0.05). It was marked with the highest TAC value of 232.6 ± 6.267 mg/g AAE and a strong DPPH scavenging activity with an IC50 of 52.81 ± 2.30 µg/mL. Correlations (p &lt; 0.05) was established between TPC,CTC, TAC and DPPH radical scavenging activity) of the extracts. Antinutrients such as; phytate, oxalate, saponins and alkaloids were found to be 7.691 ± 0.8576, 1.501 ± 0.1375, 21.33 ± 4.619 and 317.33 ± 30.29 mg/g respectively. Data obtained suggest that S. indicum possess rich bioactive compounds that can be used in neutraceuticals and food products.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

This study aims to investigate the effects of cement kiln dust (CKD) on the hydration reactions and mechanical properties of cement and to evaluate its potential for use as a supplementary cementitious material (SCM). The key variables are the CKD type and incorporation rate. Cement paste and mortar specimens containing CKD were prepared to examine their effects on the cement hydration and mechanical properties. The impact on hydration was assessed using setting time measurements, heat of hydration tests, and thermogravimetric analysis (TG). In addition, compressive strength tests were conducted to evaluate the effect of CKD on the mechanical properties of the cement. The results indicated that CKD promoted early cement hydration and enhanced the early age mechanical properties. However, owing to its lack of pozzolanic reactivity, it did not significantly affect long-term hydration. Given that the effects of CKD vary slightly depending on its chemical composition, careful consideration of CKD's properties suggests that its potential use as a SCM is promising.

Most available studies on the mechanical properties of apples lack the comprehensive results needed for the construction and validation of FEM models. Researchers typically focus on either the flesh and epidermis or the whole fruit, often overlooking the maturity stage of the examined apples. They usually report only firmness or the starch index as indicators of maturity. Furthermore, many studies use store-bought apples, which is impractical for industrial applications since this fruit have already undergone various treatments before reaching the shelf. This article aims to determine the mechanical properties of apples necessary for constructing FEM models that are both adequate and useful for the industry. The new Polish apple variety, Chopin, was selected as the research material. The study was conducted for three stages of apple maturity: development, ripening, and senescence. Mechanical properties of the flesh and skin were determined as material data for FEM models. Force-displacement curves and pressure-force functions were examined for future model validation. Using micro-computed tomography, the bruise volumes of fruit subjected to 20%, 50%, and 80% of the destructive force were determined. Significant differences were found between apples in the senescence stage and those in the development and ripening stages. Results of Micro-Ct and the results of modified and real compression tests of whole fruit have allowed us to formulate the research hypothesis regarding the influence of flesh cracking (characterized by local drops of force), influencing the bruise visibility and detection.

In this paper, a kind of single-walled carbon nanotube nonlinear model is developed, and the strongly nonlinear dynamic characteristics of such carbon nanotubes subjected to random magnetic field are studied. The nonlocal effect of microstructure is considered based on the theory of nonlocal elasticity. The natural frequency of the strongly nonlinear dynamic system is obtained by the energy function method, the drift coefficient and the diffusion coefficient are verified. The stationary probability density function of the system dynamic response is given and the fractal boundary of the safe basin is provided. Theoretical analysis and numerical simulation show that stochastic resonance occurs when varying the random magnetic field intensity. The boundary of safe basin has fractal characteristics and the area of safe basin decreases when the intensity of the magnetic field permeability increases.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

This work presents the results of optimizing the physicochemical properties of composite briquettes based on microsilica for metallurgical-grade silicon production. Microsilica, a waste product of silicon production, contains a sufficiently high amount of silicon dioxide (96-97%). This fact makes microsilica a promising composite material for metallurgical processing. However, its granulometric composition limits its direct use. The method of briquetting on an industrial briquetting press was used. The influence of the granulometric composition of the composite mixture on the heat tolerance and strength of the finished briquettes was studied. The methods of obtaining and testing the briquettes, their composition, and the briquetting and drying process are described. The obtained briquettes were tested for the smelting of metallurgical silicon. The silicon recovery rate in the metal with the standard charge was 71%, while the recovery rate with the briquetted monocharge was 85%. The results of silicon smelting from the briquettes demonstrated the high quality of the obtained metal, corresponding to the standards of metallurgical-grade silicon. The implementation of these technologies not only improves the quality of the final product but also addresses environmental issues related to the disposal of microsilica, reducing its accumulation and minimizing its impact on the environment.

Fagao is one of China's traditional gluten free staple foods made by rice or corn flour. Corn Fagao prepared by co-fermentation with sourdough and yeast exhibits better quality and less staling compared to traditional yeast-fermented Fagao. The physicochemical properties of corn Fagao batter during the sourdough-yeast co-fermentation were investigated. The results showed that compared with yeast fermentation, the gas production and viscosity of the batter increased by co-fermentation. The co-fermented batter shows higher hydrolysis of starch and less amylose content. The integrity of starch granules in co-fermented batter was damaged more seriously, the crystallinity and short-range ordered structure were less than yeast fermented batter, even though the crystal structure type of starch did not change obviously. The peak viscosity, minimum viscosity, final viscosity, decay value and recovery value of corn batter are reduced by co-fermentation, which can improve the thermal stability of the batter and slow down the aging. Co-fermentation also results in a more pronounced reduction in protein subunit contents than yeast fermentation. The changes in the physicochemical properties of corn Fagao batter help explain the quality improvement of corn Fagao made from co-fermentation method, and may provide theoretical references for co-fermentation with sourdough and yeast to other gluten free foods.

Terrestrial orchid tubers are an important source of food in some parts of Africa and are traditionally included in the diets of most rural communities in Malawi. However, there is limited information on the nutritional and phytochemical content of the Malawian orchids to substantiate their traditional use. The present study evaluates the nutritional and phytochemical variation of four orchid species: Disa zombica, Satyrium buchananii, Satyrium carsonii, and Satyrium trinerve, collected from the same ecological zone of Malawi. The proximate content, minerals, phytochemicals, and functional properties were analysed using official procedures. Protein ranged from 2.19% to 4.65%, whereas carbohydrate ranged from 65.24% to 80.22%, with S. carsonii and S. trinerve registering the highest protein and carbohydrate contents, respectively. Iron and potassium were highest in D. zombica, while sodium and calcium were highest in S. buchananii. The total phenolics ranged from 228.56 to 500.00 mg GAE/100 g, with D. zombica registering the highest. The water absorption capacity ranged from 4.10 to 10.88 g/g. Albeit variable levels, the study provides evidence that orchid species contain essential nutrients and phytochemicals important for human nutrition and health. Furthermore, the functional properties can be utilised in the development of food products, such as baked products.

Hazelnuts are one of the most valuable nuts in the world due to their unique organoleptic properties and nutritional characteristics. This work was intended to analyze some physical and chemical properties of various hazelnut cultivars grown in Zakataly (Azerbaijan), namely Ata-baba, Elbari, Topqara, Firovan, Nasimi, Qalib, Mirzebeyli, Tala, Dash findiq, Barli, Azeri and Sachaqli. In general, the results showed statistically significant differences between the studied cultivars. The density of kernels, depending on the hazelnut cultivars, varied from 0.71 g/cm³ (Azeri) up to 1. 03 g/sm³ (Sachaqli). The peeled fruits of Dash findiq were heavier on average (1.64±0.34 g), and the peeled fruits of Nasimi, Qalib, Mirzebeyli and Sachaqli were lighter on average (0.8±0.23 g, 0.8±0.31 g, 0.8±0.20 g and 0.80±0.09 g, respectively. In the unpeeled form, Dash findiq nuts were the heaviest (3.70±0.34 g), and Nasimi and Qalib nuts were the lightest of all cultivars (2.0 ±0.48 g and 2.0 ±0.36 g, respectively). Ata-baba nuts account for 49 masses per kernel. %, in other studied cultivars - 33.3- 45.3 wt. %. Nasimi nuts are rounded (in the equatorial zone); Tala, Ata-baba, Firovan and Azeri - rounded-oblong; Topqara, Barli and Dash findiq – oblong; Elbari, Qalib, Mirzebeyli and Sachaqli - elongated. Firovan, Tala and Topqara have thicker shells. Ata-baba is significantly ahead of other varieties in the yield of kernels (490 kg / 1 ton of nuts), Tala is in second place in this indicator (453 kg / 1 ton of nuts), Topqara is in third (433 kg/ 1 ton of nuts). According to the maximum fat content, the cultivars Mirzebeyli (77.00±2.20 g/100 g of kernels) and Firovan (75.0±3.08 u/100 kernels), protein - Sachaqli (16.02±0.50 u/100 kernels) and Ata-baba (15.92±0.48 g/100 g of kernels) were distinguished. The results of this study help to better understand the differences between some varieties of hazelnuts grown in Azerbaijan, which provides important clues for all players involved in this sector.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

Hypertension and arterial stiffness are the main factors contributing to cardiovascular disease. L-citrulline, a nitric oxide precursor, has been proposed as a blood pressure-lowering intervention. This study aimed to investigate the impact of L-citrulline on central and peripheral blood pressure, arterial stiffness, and muscle oxygenation at rest and during an isometric knee extension exercise protocol. Twelve older males received 6 g of L-citrulline or a placebo for six days using a double-blind crossover design. Blood hemodynamics parameters (i.e., arterial and brachial systolic and diastolic blood pressure, mean arterial pressure, pulse pressure, heart rate), arterial stiffness (i.e., augmented pressure, augmentation index, forward, backward wave pressure and carotid-femoral pulse wave velocity) and muscle oxygenation [i.e., oxyhemoglobin (Δ[O2Hb]) and deoxyhemoglobin (Δ[HHb]), total hemoglobin concentration (Δ[tHb]) and tissue saturation index (TSI%)], were measured at baseline, post-supplementation and during isometric exercise. No significant effects of L-citrulline supplementation were observed at rest or during exercise on blood pressure, arterial stiffness, and muscle blood flow. Both central and peripheral blood pressure were increased during the exercise, which is consistent with isometric contractions. The results of the present study question the efficacy of short-term L-citrulline in decreasing blood pressure at rest or attenuating blood pressure increases during isometric exercise.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Ambient vibration energy is widely being harnessed as a source of electrical energy to drive low-power devices. The vibration energy harvester (VEH) of interest employs an electromagnetic transduction mechanism, whereby ambient mechanical vibration is converted to electrical energy. The limitations affecting the performance of VEHs, with an electromagnetic transduction structure, include its operational bandwidth as well as the enclosure-size constraint. In this study, an analysis and design of a nonlinear VEH system is conducted, using the Output Frequency Response Function (OFRF) representations of the actual system model. However, the OFRF representations are determined from the Generalised Associated Linear Equation (GALE) decompositions of the system of interest. The effect of both nonlinear damping and stiffness characteristics, to respectively extend the average power and operational bandwidth of the VEH device, is demonstrated.

Background: This study aimed to contribute to the standardization of elastography by comparing stiffness values obtained from ultrasound elastography (US-E) and magnetic resonance elastography (MR-E) of the testicular parenchyma in healthy subjects. Methods: A total of 22 healthy volunteers (44 testes) were included in this study. Of the 26 cases analyzed, four were excluded from the study due to the exclusion criteria. The testicular parenchyma of the included patients was evaluated using MR-E and Shear-Wave Ultrasound Elastography (SW-E) examinations. Pearson's correlation test was used to calculate the correlation between age and stiffness values, testicular volumes and stiffness values, and stiffness values from both examinations. Results: The mean US-E stiffness of the right testes was 5.560 ± 3.1 kPa and the mean US-E stiffness of the left testes was 5.361 ± 2.9 kPa. The mean MR-E stiffness of the right testes was 6960.11 ± 460 Pa and the mean MR-E stiffness of the left testes was 6560.19 ± 310 Pa. There was no significant correlation between US-E and MR-E stiffness values (p=0.096). There was also no significant statistical correlation between US-E and MR-E stiffness values and testicular volumes (p=0.17 and p=0.093). Conclusions: No statistical correlation was found between the stiffness values obtained by SW-E and those obtained by MR-E in the normal testicular parenchyma. Additionally, no conclusive relationship between stiffness levels, age, or testicular volume was discovered.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

In this paper glass crystallization behavior of 50ZnO:47B2O3:3Nb2O3:0.5Eu2O3 (G-0h) glass has been investigated in detail by DSC, XRD and TEM analysis. The luminescent properties of resulted glass-ceramics were also investigated. By XRD and TEM analysis crystallization of several crystalline phases have been proved (α-Zn3B2O6, β-Zn3B2O6 and ZnNb2O6). By calculating of crystal parameters it was found that europium ions are successfully incorporated in the β-Zn3B2O6. Photo-luminescent spectra show an increased emission in the resulting glass-ceramic samples as compared with the parent glass sample because of the higher asymmetry of Eu3+ ions in the crystalline phases obtained. It was established that the optimum emission intensity is registered for glass-ceramic sample obtained after 25 hours heat treatment of the parent glass.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

The ability of thermoresponsive polymers to respond to temperature with a reversible conformational change makes them promising ‘smart’ materials for solutions in medical and biotechnological applications. In this work, two such polymers and structural isomers were studied: poly(N-isopropyl acrylamide) (PNiPAm) and poly(2-isopropyl-2-oxazoline) (PiPOx). We compare the critical solution temperatures (CST) of these polymers in D2O and H2O in the presence of Hofmeister series salts, as results obtained under these different solvent conditions are often compared. D2O has a higher dipole moment and electronegativity than H2O, which could significantly alter the CST transition. We used two complementary methods to measure the CST, dynamic light scattering (DLS) and differential scanning calorimetry (DSC), and found that the CST decreased significantly in D2O compared to H2O. In the presence of highly concentrated kosmotropes, the CST of both polymers decreased in both solvents. The influence of the kosmotropic anions was smaller than the water isotope effect at low ionic strengths but considerably higher at physiological ionic strengths. However, the Hofmeister anion effect was quantitatively different in H2O than in D2O, with the largest relative differences observed for Cl-, where the CSTs in D2O decreased more than in H2O measured by DLS but less by DSC. PiPOx was more sensitive than PNiPAm to the presence of chaotropes. It exhibited much higher transition enthalpies and multistep transitions, especially in aqueous solutions. Our results highlight that measurements of thermoresponsive polymer properties in D2O cannot be compared directly or quantitatively to application conditions or even measurements performed in H2O.

This paper reveals some properties of the cumulative entropy of consecutive k-out-of-n:F system's lifetime. First, we introduce a method for calculating the cumulative entropy of their lifetime and explore its preservation properties using established stochastic orders. Ad- ditionally, we obtain useful bounds that can used in situations where the distribution function of the system's component lifetimes are complicated or systems have large components. To support practical applications, we present two nonparametric estimators for the cumulative entropy of these systems. The efficiency and performance of these estimators are illustrated with simulated datasets and further validated with real data sets.

Arthroscopic capsular release (ACR) is used for persistent shoulder stiffness after an index surgery. No cases of post-ACR humeral head osteonecrosis have been reported to date. A 56-year-old male patient underwent open reduction and internal fixation using a hook plate for acromioclavicular joint dislocation. Despite hardware removal, the patient presented with unresolved shoulder pain and range-of-motion (ROM) limitation. He had a history of hypertension, chronic hepatitis B infection, and alcohol consumption. Preoperative ROM was forward flexion 90°and internal rotation sacral level. Preoperative functional status was visual analog scale (VAS) score 4, American Shoulder and Elbow Surgeons (ASES) score 51, and Constant–Murley (CMS) score 48, and normal radiography and magnetic resonance imaging. Standard ACR was performed with 360° release of the joint capsule via electrocautery ablation. Six-months post-ACR, ROM (forward flexion: 135°, abduction: 135°, external rotation: 70°, internal rotation: T10 vertebra) and functional outcomes (VAS 2; ASES79; CMS 75) were significantly improved, without interval change in radiographic assessment. However, 21 months later, he had recurrent shoulder pain and decreased ROM. Radiography revealed humeral head osteonecrosis. Patients with intrinsic or extrinsic risk factors related to humeral head circulation disturbance should be monitored for humeral head osteonecrosis post-ACR.

Background: We aimed to determine the splenic stiffness (SS) values in healthy individuals as measured by 3 Tesla magnetic resonance elastography (3T MRE) and to investigate the possible effects of parameters such as age, sex, spleen volume, diameter, and parenchyma thickness on SS.Methods: A total of 54 healthy volunteers were included in this cross-sectional study. Participants' age and sex information were recorded, in addition to spleen craniocaudal and anteroposterior diameter, cortical thickness, spleen volume, and SS, which were measured using 3T magnetic resonance imaging and MRE. Results: Twenty-nine male and 25 female subjects with a mean age of 54.78±15.40 years were included in the study. Mean cradiocaudal diameter was 10.46±1.16 cm, anteroposterior diameter was 9.88±1.29 cm, parenchyma thickness was 4.08±0.67 cm, SS was 3721.94±709.69 Pascal (Pa), and median spleen volume was 292.54 (239.40-311.00) cm³. A significant positive correlation was observed between age and SS (r=0.779, p<0.001). The SS values were not associated with sex, craniocaudal diameter, anteroposterior diameter, parenchymal thickness, or volume.Conclusion:Age should be considered when using SS in the diagnosis and staging of relevant diseases such as portal hypertension and esophageal varices. Our results should be confirmed by future studies using 3T MRE in larger populations.

Background: We aimed to determine the splenic stiffness (SS) values in healthy individuals as measured by 3 Tesla magnetic resonance elastography (3T MRE) and to investigate the possible effects of parameters such as age, sex, spleen volume, diameter, and parenchyma thickness on SS. Methods: A total of 54 healthy volunteers were included in this cross-sectional study. Participants' age and sex information were recorded, in addition to spleen craniocaudal and anteroposterior diameter, cortical thickness, spleen volume, and SS, which were measured using 3T magnetic resonance imaging and MRE. Results: Twenty-nine male and 25 female subjects with a mean age of 54.78±15.40 years were included in the study. Mean cradiocaudal diameter was 10.46±1.16 cm, anteroposterior diameter was 9.88±1.29 cm, parenchyma thickness was 4.08±0.67 cm, SS was 3721.94±709.69 Pascal (Pa), and median spleen volume was 292.54 (239.40-311.00) cm3. A significant positive correlation was observed between age and SS (r=0.779, p<0.001). The SS values were not associated with sex, craniocaudal diameter, anteroposterior diameter, parenchymal thickness, or volume Conclusion:Age should be considered when using SS in the diagnosis and staging of relevant diseases such as portal hypertension and esophageal varices. Our results should be confirmed by future studies using 3T MRE in larger populations.

This study investigates the optical properties of Yttrium Orthoferrite thin films fabricated via plasma laser deposition. Yttrium Orthoferrite, a ferrimagnetic material known for its potential applications in spintronics and photonics, was deposited on single-crystal substrates under controlled conditions to analyze its optical characteristics. The influence of deposition time, on the film quality and optical properties was examined.

The targeted compounds in this research, resveratrol analogs 1–14 were synthesized as mixtures of isomers by the Wittig reaction using heterocyclic triphenylphosphonium salts and various benzaldehydes. The planned compounds were those possessing the trans-configuration as the biologically active trans-resveratrol. The pure isomers were obtained by repeated column chromatography in various isolated yields depending on the heteroaromatic ring. It was found that butyrylcholinesterase (BChE) was more sensitive to the heteroaromatic resveratrol analogs than acetylcholinesterase (AChE), except for 6, the methylated thiophene derivative with chlorine, which showed equal inhibition toward both enzymes. Compounds 5 and 8 achieved the highest BChE inhibition with IC50 values of 22.9 and 24.8 μM, respectively. The same as with AChE and BChE, methylated thiophene subunits of resveratrol analogs showed better enzyme inhibition than unmethylated ones. Two antioxidant spectrophotometric methods, DPPH and CUPRAC, were applied to determine the antioxidant potential of new heteroaromatic resveratrol analogs. Molecular docking of these compounds was conducted to visualize the ligand-active site complexes' structure and identify the non-covalent interactions responsible for the complex's stability, which influence the inhibitory potential. As ADME properties are crucial in developing drug product formulations, they have also been addressed in this work. The potential genotoxicity is evaluated by in silico studies for all compounds synthesized.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 &lt; 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

Chronic hemodialysis (HD) patients have very high cardiovascular risk. Acute vascular changes during dialysis mediated by factors of the endothelium may have a crucial role in this. Aim: To study acute vascular changes during HD. In 29 consecutive chronic HD patients (age: 65.6±10.4 years) pre-, mid-, and post-HD plasma syndecan-1 (SDC-1) and endothelin-1 (ET-1) levels were measured. Applanation tonometry was performed before HD. SDC-1 levels increased during HD (p=0.004). Males had higher ET-1 levels. Patients were divided into 2 groups based on pulse wave velocity (PWV): PWV≥12 m/s and PWV<12 m/s. Pre-HD and mid-HD SDC-1 levels were higher in the group with PWV≥12 m/s (10.174±2.568 vs. 7.928±1.794 ng/ml, p=0.013, and 10.319±3.482 vs. 8.248±1.793 ng/ml, p=0.044, respectively). Post-HD ET-1 levels were higher in the patient group having PWV≥12 m/s (10.88±3.00 vs. 8.05±3.48 pg/l, p=0.027). Patients having PWV≥12 m/s had higher pre-HD peripheral and aortic systolic blood pressure (p<0.05). Total cholesterol correlated with the SDC-1 decrease during HD (r=0.539; p=0.008). Pre-, mid-, and post-HD SDC-1 correlated with the ultrafiltration (r=0.432, p=0.019; r=0.377, p=0.044; and r=0.401, p=0.012, respectively). SDC-1 and ET-1 contribute to vascular changes observed during HD, and they have correlations with some cardiovascular risk factors.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

As the carbon storage capacity of timber is recognized, there is growing interest in timber and wooden structures as a solution to various environmental problems. The use of Korean timber with substantial carbon storage capacity is required to reduce Korean carbon emissions and circulate timber resources. In this study, fire tests were conducted to investigate the charring properties of glued laminated timber columns made of Korean larch. The fire tests were conducted under both load-bearing and non-load-bearing conditions. The fire test results showed that the charring depth was affected by the corners of the section, and that the load ratio had an insignificant influence on the charring depth when the load ratio was 0.9 or less. This study provides data that can be used to compare the charring properties of laminated wood produced using South Korean larch with the charring properties of foreign standards. This provides reference data for developing fire-resistant design standards for timber structures made from South Korean timber.

Cementitious materials exhibit excellent binding properties and micropore structures that support the stabilization of TiO2 nanoparticles within the matrix. Therefore, these materials are ideal for the development of functional construction products with TiO2 nanoparticles. This study investigated the degree of hydration, microstructure, and mechanical properties of cement-containing TiO2 nanoparticles. The experimental results demonstrated that TiO2 nanoparticles accelerated the hydration rate of cement, reducing the setting times. Moreover, TiO2 nanoparticles changed matrix microstructure, decreasing the porosity and improving early-age strength. Although TiO2 nanoparticles function as nucleation sites in the cement hydration reaction, the tendency of the particles to clump implies that proper dispersion should be ensured when mixing in large quantities. When developing new building materials incorporating TiO2 nanoparticles, considering the effect of TiO2 nanoparticles on the hydration reaction of cementitious materials is crucial.

The pursuit of materials that offer both wear comfort and protection for functional and protective clothing has led to the exploration of weft-knitted spacer structures. Traditional cushioning materials such as spacer fabrics and laminated foam often suffer from deformation under compression stresses, thus compromising their protective properties. This study investigates the enhancement of the force absorption, stress-strain and thermal properties of weft-knitted spacer fabrics with inlays. Surface yarns with optimal stretchability and thermal properties are used and combined with elastic yarns in various patterns to fabricate nine different inlay samples. The mechanical and thermal properties of these samples are systematically analyzed, including their compression, stretchability, thermal comfort and surface properties. The results show that the inlay spacer fabric exhibits superior compression properties and thermal conductivity compared to traditional laminated foam and spacer fabrics, while maintaining stretchability, thus providing a better performance than traditional fabrics for protective clothing and wearable cushioning products. This study further confirms that the type of inlay yarn and inlay structure are crucial factors that significantly influence the thermal, tensile and compressive properties of fabric. This research provides valuable insights into the design and development of advanced textile structures to improve wear comfort and protection in functional garment applications.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

Visible-light photocatalysis, particularly in its application to organic synthesis, has experienced a big renaissance in the past decade. The rational design of new photocatalysts with designed and improved photocatalytic properties, that at the same time circumvents the necessity of using scarce and toxic transition metals, will predictably play a key role in photocatalysis in the next few years. Although free-base porphyrins were identified some years ago as a promising, easily accessible and easily tunable class of organic photoredox catalysts, a systematic study on the effect of the electronic nature and of the position of the substituents on both the ground-state and the excited-state redox potentials of these compounds is still lacking. We have prepared a set of known functionalized derivatives of meso-tetraphenyl porphyrin containing different substituents either in one of the meso-positions or at a beta-pyrrole carbon and we have determined their ground- and (singlet) excited-state redox potentials. This survey has led us to conclude that the introduction of a carbonyl group at the beta-pyrrolic position strongly increases the facility of the monoelectronic reduction of the porphyrin both in the ground state and in the singlet excited state. We have also prepared a second set of four previously unknown benzoyl derivatives of meso-tetraphenylporphyrin, and we have confirmed the validity of our conclusions.

The unique structure of G4.0 PAMAM dendrimers allows the drug to be enclosed in internal spaces or immobilized on the surface. In the conducted research, the conditions for the formation of the active G4.0 PAMAM complex with doxorubicin (DOX) were optimized. The physicochemical properties of the system were monitored using DLS, CD, and fluorescence spectroscopy. The QCM-D method was chosen to determine the preferential conditions for the complex formation. The highest binding efficiency of the drug to the cationic dendrimer was observed under basic conditions when the DOX molecule was deprotonated. The decrease in the zeta potential of the complex confirms that DOX immobilizes through electrostatic interaction with the carrier's surface amine groups. The binding constants were determined from the fluorescence quenching of the DOX molecule in the presence of G4.0 PAMAM. The two-fold way of binding doxorubicin in the structure of dendrimers was visible in the ITC isotherm. Fluorescence spectra and release curves identified reversible binding of DOX to the nanocarrier. Among the selected cancer cells, the most promising anticancer activity of G4.0-DOX was observed in A375 malignant melanoma cells. Moreover, the preferred intracellular location of the complexes concerning the free drug was found, which is important from a therapeutic point of view.

The article presents the results of research work devoted to improving the characteristics of paint and varnish coatings based on aqueous dispersions of polyacrylates, it is proposed to modify them by introducing mineral raw materials as fillers and hydrated lime with subsequent processing in a vortex layer apparatus. Introduction of activated diatomite does not cause deterioration of covering power, adhesion and increase of porosity of the paint material. Modification of coatings contributes to the increase of their operational properties, which can be associated with the reduction of free volume in the composite, formation of polymer boundary layers with modified physical and chemical properties. The aim of the study is to obtain water-dispersion paint and varnish composition containing modified diatomite on polyacrylate basis and subsequent study of the main physical and mechanical parameters. The work has been carried out by the following method: determination of porosity, adhesion, elasticity, covering power of the control composition; determination of porosity, adhesion, elasticity, and covering power of the obtained composites using modified filler; investigation of the influence of radiation in the infrared spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of research works it was noticed that modification of water dispersions with silica activated diatomite helps to eliminate the main disadvantages of materials and coatings based on acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate base does not lead to deterioration of the main performance characteristics of paint coatings - porosity, adhesion, elasticity and covering.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

The accuracy of cosmic ray observation by the Large High Altitude Air Shower Observatory Wide Field-of-view Cherenkov/fluorescence Telescope Array (LHAASO-WFCTA) is influenced by variations in aerosols in the atmosphere. The solar photometer (CE318-T) is extensively utilized within the Aerosol Robotic Network as a highly precise and reliable instrument for aerosol measurements. With this CE318-T 23, 254 sets of valid data samples in 394 days from October 2020 to October 2022 at the LHAASO site were obtained. Data analysis revealed that the baseline Aerosol Optical Depth (AOD) and A˚ngstro¨m Exponent (AE) at 440-870 nm (AE440−870nm) of the aerosols were calculated to be 0.03 and 1.07, respectively, suggesting that the LHAASO site is among the most pristine regions on Earth. The seasonality of the mean AOD are the order of spring &gt; summer &gt; autumn = winter. The monthly average maximum of AOD440nm occurred in April (0.11 ± 0.05) and the minimum was in December (0.03 ± 0.01). The monthly average of AE440−870nm exhibited slight variations. The seasonal characterization of aerosol types indicated that clean continental background aerosol predominated in autumn and winter, which is the optimal period for the absolute calibration of the WFCTA. Additionally, the diurnal daytime variations of AOD and AE across the four seasons are presented. Our analysis also indicates that the potential origins of aerosol over the LHAASO in four seasons were different and the atmospheric aerosols with higher AOD probably originate mainly from Northern Myanmar and Northeast India region. These results provide a baseline for comparison to the future on-site measurement of extinction coefficient profile and aerosol phase function by LHAASO-WFCTA, also enrich the valuable materials on aerosol observation in the Hengduan Mountains and Tibetan Plateau.

(1) Background: Globally, neck pain is prevalent, affecting around thirty percent of the population annually. To better understand the influence of pain on the myofascial layers, the present study investigated these on the upper trapezius muscle in unilateral, more severe neck pain. (2) Methods: This study was a cross-sectional study. Forty patients (42.2 ± 14.7) with a confirmed diagnosis of unilateral neck pain were examined using durometry and indentometry. The study evaluated stiffness, elasticity, and pressure pain threshold of both sides of the neck (symptomatic side: SS; healthy side: HS). Furthermore, the range of motion of the cervical spine (lateral flexion, rotation) was quantified using a digital goniometer. (3) Results: A significant lateral discrepancy was observed in stiffness between groups (durometry: SS – 33.76 ± 7.78, HS – 29.75 ± 7.45, p&lt;0.001; indentometry: SS – 59.73 ± 33.93, HS – 4.18 ± 12.69, p=0.024). In contrast, no differences were found between the comparison sides of the upper trapezius for the parameter’s elasticity (SS – 0.101 ± 1.09, HS – -0.006 ± 0.29, p=0.416), cervical spine mobility (lateral flexion: SS – 37.08 ± 8.15, HS – 37.73 ± 7.61, p=0.559; rotation: SS – 73.55 ± 12.37, HS – 72.85 ± 11.10, p=0.660) and algometry (SS – 36.41 ± 17.53, HS – 37.22 ± 17.00, p=0.657). (4) Conclusion: Overall, it can be concluded that more severe neck pain unilaterally shows differences in stiffness on the same side. Future research is needed to investigate the links.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Broad bean paste (BBP) is a traditional fermented soy food, and its high salt content not only prolongs the fermentation time but also threatens human health. In this study, three BBP-meju with different salt concentrations were prepared, and the effects of varying salinity on the fermentation process were comprehensively compared. The results showed that salt-reduced fermentation contributed to the accumulation of amino acid nitrogen, reducing sugars, free amino acids, and organic acids. Alcohols, esters, aldehydes, and acids were the main volatile flavor compounds in BBP-meju, and the highest total volatile flavor compounds were found in medium-salt meju. Bacillus, Staphylococcus, Aspergillus, and Mortierella were the dominant microbial communities during fermentation, and there were also three opportunistic pathogens, Enterobacter, Pantoea, and Brevundimonas, respectively. According to Spearman correlation analysis, Wickerhamomyces, Bacillus, Staphylococcus, and Mortierella all showed highly significant positive correlations with ≥3 key flavor compounds, which may be the core functional flora. Furthermore, the dominant microbial genera worked synergistically to promote the formation of high-quality flavor compounds and inhibit the production of off-flavors during salt-reduced fermentation. This study provides a theoretical reference for the quality and safety control of low-salt fermented soy foods.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

This study introduces a novel and sustainable method of producing graphene from coconut shells and investigates its application in Graphene, Ni/Graphene, and Zn/Graphene electrodes for advanced energy storage devices. The graphene was synthesized scalably using a pyrolysis and impregnation technique, with its successful synthesis verified by X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), and electrical conductivity measurements characterizations. The study highlights the enhanced performance of Zn/Graphene electrodes, which outperform both pure graphene and Ni/Graphene variants. This superior performance is attributed to the smaller particle size of Zn (mean = 2.356 µm) compared to Ni (mean = 3.09 µm), and Zn’s more favorable electron configuration for electron transfer. These findings demonstrate the potential of bio-derived graphene composites as efficient, high-performance electrodes, paving the way for more sustainable and cost-effective energy storage solutions.

Freeze drying (FD) is a technique used to preserve the bioactive content and flavor of samples. Foods with a short shelf life due to nature have been preserved by FD in recent years. The success of the drying technique is thanks to the high retention ability of the bioactive compounds and the flavor of the sample. However, the high cost and energy consumption of the FD limit its usage in several fields. Freezing, primary drying, and secondary drying, which take place in the same device, are the stages of the FD. In addition, several parameters, including pretreatment, size, temperature, sample species, time, and pressure, affect the FD process. These parameters are controlled to increase the effectiveness of the FD on the samples. Moreover, FD was compared with other drying techniques including hot-air drying, microwave drying, vacuum drying, and solar drying to determine its protective capability. It has also been applied to the valorization of waste products, which is a common problem worldwide. For valorization, microencapsulation and powder production have been achieved by FD. In recent years, studies on the effects and use of the FD on various materials increased, providing new aspects for the future of science and food industry.