We apply the stochastic thermodynamics formalism to describe the dynamics of systems of complex Langevin and Fokker-Planck equations. We provide in particular a simple and general recipe to calculate thermodynamical currents, dissipated and propagating heat for networks of nonlinear oscillators. By using the Hodge decomposition of thermodynamical forces and fluxes, we derive a formula for entropy production that generalises the notion of non-potential forces and makes transparent the breaking of detailed balance and of time reversal symmetry for states arbitrarily far from equilibrium. Our formalism is then applied to describe the off-equilibrium thermodynamics of a few examples, notably a continuum ferromagnet, a network of classical spin-oscillators and the Frenkel-Kontorova model of nano friction.

Transient conjugate heat transfer measurements under varying temperature and velocity inlet boundary conditions at incompressible flow conditions were performed for flat plate and ribbed channel geometries. Therefrom local adiabatic wall temperatures and heat transfer coefficients are determined. Those data are analyzed using typical heat transfer correlations, e.g. Nu=CRe^mPr^n determining the local distribution of C and m. It is shown that they are closely linked. A relationship lnC=A−mB is observed with A and B as modeling parameters. They could be related to parameters in log law or power law representations for turbulent boundary layer flows. The parameter m is shown to have a close link to local pressure gradients and therewith near wall streamlines as well as friction factor distributions. A normalization of the C parameter allows to derive a Reynolds analogy factor and therefrom local wall shear stresses.

This paper introduces a new adaptation of the enthalpic lattice Boltzmann method (LBM) tailored to simulate the intricate dynamics of conjugate heat transfer in non-homogeneous media, showcasing considerable potential for enhancing heat exchanger designs. This approach expands upon the conventional enthalpic LBM framework by seamlessly incorporating tailored source terms, enabling precise representation of local and transient variations in the medium’s thermophysical properties. The resulting LBM model comprehensively captures the energy conservation equation, with exceptions made only for flow compressibility and viscous dissipation, thereby significantly augmenting its versatility in analyzing heat exchanger configurations. Verification tests, comprising assessments of both transient and steady-state solutions, unequivocally validate the accuracy of the proposed model, further bolstering its reliability for analyzing heat exchange processes within intricate heat exchanger geometries. To demonstrate its efficacy, simulations of conjugate heat transfer processes involving fluid natural convection within structured cavities were performed, imposing both Dirichlet and Neumann boundary conditions to emulate scenarios encountered in practical heat exchanger operations. The findings yield compelling insights, particularly in the transient regime, revealing the beneficial impact of structured cavities on enhancing heat transfer processes. These insights inform potential design optimizations for heat exchangers. The results emphasize the potential of the modified enthalpic LBM approach to elucidate complex heat transfer phenomena in non-homogeneous media and structured geometries, offering valuable implications for heat exchanger engineering and optimization.

Nucleation is a fundamental and general process at the initial stage of first order phase transition. Although various models based on the classical nucleation theory (CNT) have been proposed to explain the energetics and kinetics of nucleation, detailed understanding on nanoscales are still required. Here we focus on homogeneous bubble nucleation, in which evaluation of the size dependence of bubble free energy is the key issue. We propose application of a formula in stochastic thermodynamics, the Jarzynski’s equality, for data analysis of molecular dynamics (MD) simulation to evaluate the free energy of bubble nucleation. As a test case, we performed a series of MD simulations with Lennard-Jones (LJ) fluid system. By applying an external spherical force field to equilibrated LJ liquid, we evaluated the free energy change during bubble growth as the Jarzynski’s ensemble average of required works. A fairly smooth free energy curve was obtained as a function of bubble radius in metastable liquid of mildly negative pressure conditions.

Interaction between multiple phases especially liquid-gas is one of the most common phenomena in industrial systems. Computer Vision enables modern systems to derive an automated and robust image-processing technique to address this issue. However, diverse experimental conditions still make it a challenging task to overcome. In Deep Learning, instance segmentation has created a niche in various computer vision applications as it aims to provide different instance IDs to objects belonging to the same class. In this paper, we propose a novel approach employing the YOLO (You Look Only Once) an end-to-end deep learning architecture for the detection and segmentation of bubbles in fluid flows. YOLOv5 offers significant improvements in both speed and accuracy compared to its predecessors like YOLOv3. Therefore, we train the YOLOv5 network on a dataset consisting of annotated images representing instances of bubbles across varied fluid flow environments. This paper provides both qualitative and quantitative evaluation of three YOLOv5 networks (small, medium, and extra-large) in detecting and segmenting bubbles with high accuracy and efficiency. Based on the metrics all three YOLOv5 models achieved high precision above 0.98 for bounding box detection and 0.97 for segmentation mask, and high recall value greater than 0.97 for box and 0.96 for mask quality was achieved. The achieved results indicate that the models accurately localize bubbles within the image frame, and distinguish bubble pixels from the background. Also, mean average precision (mAP50-95) consistently exceeds 0.84 across all models for the bounding box and 0.73 for the segmentation mask. The ascertained results emphasize the potential of YOLOv5 architecture as a powerful tool for automated bubble analysis in real-world applications. Our research contributes to advancing the field of deep neural networks in fluid systems and provides a fresh approach for future developments in automated bubble analysis.

In this paper, the elemental construct of an I-shaped fin cooling a heat generating volume is studied through the entropy production perspective. Using the constructal design method framework with entropy production minimization as an objective leads to different optimal shape ratio, different from the ones obtained using the excess of temperature. Moreover, the optimal shape ratio evolution is not necessary the same for local entropy production minimization (excess of entropy production) and global entropy production (entropy produced in the whole area). Finally, an analysis on a possible dimensionless number is introduced for the study of constructal plates.

As the demand of heating and air conditioning is increasing day by day due to getting a comfortable life, for that reason, the market for heat pump and air conditioning systems or both, is seeing a steady increase in low global warming potential. All researchers on heat pump and air conditioning systems are searching for environmentally friendly refrigerants. However, a significant number of contemporary refrigerants (HCFCs) have the potential to cause global warming and ozone depletion, such as those found in heat pump air conditioning systems. Using more environmentally friendly refrigerants, including hydrocarbon and blend refrigerant mixtures, is one way to lower GWP and Ozone depletion potential. This study examines the performance of several alternative refrigerants, including R32, R134A, R410A, R22, and R290. In order to examine the performance of R290, theoretical and simulation results are compared on various refrigerants while taking into account a number of performance parameters, including the refrigerant energy efficiency ratio, mass flow rate, coefficient of performance, cooling capacity, and compressor work for one ton of refrigeration (1TR) air conditioners. One player with a very low GWP is R290. However, the only drawback is that it can catch fire and is hazardous to use in split-type commercial heat pump air conditioning applications. The environmental and thermo physical properties of HC-290 are significantly better than those of other materials, according to theoretical and simulation studies utilizing Cool Pack software, hence it is a viable replacement.

The objective of this work is to analyze the improvement of heat transfer in trapezoidal fin heat exchangers using numerical simulation. Heat exchangers are essential components frequently used in contemporary electronic gadgets to effectively disperse heat produced by high-power components. Nevertheless, as electronic devices continue to advance and become more powerful, the heat transfer capacity of heat exchangers is facing more requirements, therefore requiring enhanced heat dissipation efficiency. Afterwards, various fin angles were adjusted, and the heat transmission efficiency was compared. Modifying the angles can significantly improve the effi-ciency of convective heat dissipation. Moreover, it has been found that employing an optimized trapezoidal fin structure can further enhance the efficiency of heat transfer. The results indicate that trapezoidal fin heat exchangers provide superior heat dissipation efficiency compared to conventional heat exchangers. This is important for enhancing the thermal dissipation capabili-ties of electrical gadgets, hence guaranteeing steady functionality and extending their longevity. Subsequent study might explore supplementary methods to boost heat transmission in different heat exchanger configurations in order to meet the growing requirements for heat dissipation.

The heat and matter transfer during glucose catabolism in living systems and their relation with entropy production are a challenging subject of the classical thermodynamics applied to biology. In this respect, an analogy between mechanics and thermodynamics has been performed via the definition of the entropy density acceleration expressed by the time derivative of the rate of entropy density and related to heat and matter transfer in minimum living systems. Cells are regarded as open thermodynamic systems that exchange heat and matter resulting from irreversible processes with the intercellular environment. Prigogine’s minimum energy dissipation principle is reformulated using the notion of entropy density acceleration applied to glucose catabolism. It is shown that, for out-of-equilibrium states, the calculated entropy density acceleration is finite and negative and approaches as a function of time a zero value at global thermodynamic equilibrium for heat and matter transfer independently of the cell type and the metabolic pathway. These results could be important for a deeper understanding of entropy generation and its correlation with heat transfer in cell biology with special regard to glucose catabolism representing the prototype of irreversible reactions and a crucial metabolic pathway in stem cells and cancer stem cells.

The use of entropy concepts in the field of stochastic electrodynamics is briefly reviewed here. Entropy calculations to date that have been fully carried out are discussed in two main situations: first, where electric dipole oscillators interact with zero-point, or zero-point plus Planckian, or Rayleigh-Jeans radiation, and second where only these radiation fields exist within a cavity. The emphasis here will be on the first more difficult situation where both charged particles and radiation fields are present and interacting. Unlike the usual exposition on entropy in clasical statistical mechanics involving probabilistic notions of phase space occupation, the calculations to date for both particles and fields or for fields alone, follow the caloric entropy method where the notions of heat flow, adiabatic surfaces, and isothermal conditions, are utilized. Probability notions certainly still enter into the calculations, as the fields and charged particles interact stochastically together, following Maxwellian electrodynamics. Examples of phase-space calculations for harmonic oscillators and classical hydrogen atoms are carried out, emphasizing how much farther caloric entropy calculations have been successfully utilized.

This work probes the combined effects of magnetic field and viscous dissipation on heat field and examine the second law analysis (entropy generation) in an electrically conducting fluid under the effect of wall mass transfer over continuous stretched non-isothermal surface with variable viscosity. The viscosity of the fluid is assumed to be an inverse linear function of temperature. The governing equation for the problem are changed to dimensionless ordinary differential equations by using similarity transformation and solved numerically by using Rung Kutta and Shooting technique. Velocity, concentration and temperature distribution are obtained and used to compute the entropy generation and the Bejan number in the flow field. The effect of variable viscosity, Schmidt number, Hartman and Reynolds number on the velocity, concentration, temperature, entropy generation and Bejan number are studied and discussed.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Over the years, the need for autonomous systems such as drones, also known as unmanned aerial vehicles (UAVs), has significantly increased in popularity across several industries, including the military. The Internet of Battlefield Things (IoBT) represents a modern technological advancement that significantly enhances the operational efficacy of defense systems. It establishes an integrated military force by connecting individuals to intelligent technology in drones, radios, equipment, antennas and ground stations. This is achieved through the utilization of cloud and edge computing, sensors, mobile devices, embedded systems, and IoT-based systems. However, IoBT security is significantly compromised by enemies that exploit the vulnerabilities and malicious intrusions that specifically target the external environment or to obtain sensitive data. In addition, a comprehensive understanding of cyberattacks and countermeasures is essential for assuring the security of IoBT. On the other hand, as cyber threats get more complicated, trust becomes increasingly important for the security of digital systems. Within this context, the zero trust architecture contends that the security of a complex network is inherently vulnerable to internal and external threats. In defense, UAV security system applications, for example, the primary purpose of the zero trust architecture is to limit the vulnerability of military UAV systems to cyberattacks, hence reducing the possibility of data breaches and illegal entry. This study conducts a systematic review aimed at identifying different aspects of cybersecurity strategies for protecting UAV systems within the IoBT domain. Furthermore, zero trust architecture is presented in the study as an effective prospective solution to the security issues that develop in defense UAV systems.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

Here we investigate how the local properties of particles in a thermal bath may influence the thermodynamics of the bath, and consequently alter the statistical mechanics of subsystems that comprise the bath. We are guided by the theory of small-system thermodynamics, which is based on two primary postulates: that small systems can be treated self-consistently by coupling them to an ensemble of similarly small systems, and that a large ensemble of small systems forms its own thermodynamic bath. We adapt this “nanothermodynamics” to investigate how a large system may subdivide into an ensemble of smaller subsystems, causing internal heterogeneity across multiple size scales. For the semi-classical ideal gas, maximum entropy favors subdividing a large system of “atoms” into an ensemble of “regions” of variable size. The mechanism of region formation could come from quantum exchange symmetry that makes atoms in each region indistinguishable, while decoherence between regions allows atoms in separate regions to be distinguishable by their distinct locations. Combining regions reduces the total entropy, as expected when distinguishable particles become indistinguishable, and as required by a theorem in quantum mechanics for sub-additive entropy. Combining large volumes of small regions gives the usual entropy of mixing for a semi-classical ideal gas, resolving Gibbs paradox without invoking quantum symmetry for atoms that may be meters apart. Other models presented here are based on Ising-like spins, which are solved analytically in one dimension. Focusing on the bonds between the Ising-like spins we find similarity in the equilibrium properties of a two-state model in the nanocanonical ensemble and a three-state model in the canonical ensemble. Thus, emergent phenomena may alter the thermal behavior of microscopic models, and the correct ensemble is necessary for fully-accurate predictions. Another result using Ising-like spins involves simulations that include a nonlinear correction to Boltzmann’s factor, which mimics the statistics of indistinguishable states by imitating the dynamics of spin exchange on intermediate lengths. These simulations exhibit 1/f-like noise at low frequencies (f), and white noise at higher f, similar to equilibrium thermal fluctuations found in many materials.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

As modern systems are becoming more complex their control strategy cannot longer relay only on measurement information that usually comes from probes but also from mathematical models. Those systems models can lead to unbearable computation times due to their own complexity, turning the control process non-viable, which leads to the implementation of surrogate models that enable to achieve estimates within acceptable time to take decisions. A control trained with Deep Reinforcement Learning algorithm, using a Physics-Informed Neural Network to obtain the temperature map on the following time step, replaces the need of running Direct Numerical Simulations. On this work we considered an 1D heat conduction problem, which temperature distribution feeds a control system to activate a heat source aiming to obtain a constant, previously defined, temperature value. With this approach, control training becomes much faster without the need of performing numerical simulations or laboratory measurements, as well the control is taken based on Neural Network enabling its implementation on simple processors to edge computing.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

The plate fin heat exchanger is the compact heat exchanger applied in many industries because of its high thermal performance. To enhance the heat transfer of plate fin heat exchanger in further, three new kinds of wavy plate fins, namely perforated wavy fin, staggered wavy fin and discontinuous wavy fin are proposed and investigated by CFD simulations. The effects of key design parameters, including that of waviness aspect ratios, perforation diameters, stagger ratios and breaking distance are investigated, respectively, with the Reynolds number changes from 500 to 4500. It is found that due to the swirl flow and efficient mixing of fluid, the perforation, serration and breaking techniques are beneficial for the enhancement of heat transfer compared to the traditional wavy fin. At the same time, serration is beneficial to reduce the friction factor, and the breaking technique can reduce heat transfer area as well as enhance heat transfer performance. Through the performance evaluation criteria, the staggered wavy fin has an advantage over the small waviness aspect ratio compared to the perforated wavy fin. The maximum performance evaluation criteria (PEC), as high as 1.24, can be obtained for the perforated wavy fin at the largest waviness aspect ratio.

The fitting and modeling of skewed, complex, symmetric, and asymmetric datasets is an exciting research topic in many fields of applied sciences, notably lifetime, medical, and financial sciences. The Heavy tailed Nadarajah Haghighi model is introduced by compounding the heavy tailed family and Nadarajah Haghighi distribution in this paper. The so obtained model has three parameters accounting for the scale and shape of the distribution. The proposed distribution's fundamental characteristics such as probability density, cumulative distribution, hazard rate, and survival functions are provided, and several key statistical properties are established, and several entropy information measures are proposed. The estimation of model parameter is performed via the ML procedure. Further, different simulation experiments are conducted to demonstrate the performance of proposed estimator’s using some measure, like the average estimate, the average bias, and associated mean square error. Finally, we are applied our proposed model to analyze three different real datasets. In our illustration, we are compared the practicality of the recommended model with several well-known competing models.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

Real assets in the energy market are subject to ecological uncertainty due to the penetration of renewables. We illustrate this point by analysing electrolysers, a class of assets which recently became the subject of a large interest, as they lead to the production of the desirable green hydrogen and green ammonia. The latter has the advantage of being easily stored and has huge potential in decarbonising both the fertilizer and shipping industries. We consider the optimization of green ammonia production with different types of electricity procurement in the context of stochastic power and ammonia markets, a necessary assumption to translate the features of renewable, hence intermittent, electricity. We emphasise the importance of using stochastic prices to effectively model the volatile nature of the price dynamics, illustrating the project risks that can be mitigated by hedging activities. This study shows the pivotal role of flexibility when dealing with fluctuating renewable production and volatile electricity prices to maximise profits and better manage risks.

Double-spiral galaxies are common in the Universe. It is known that the logarithmic double spiral is a Maximum Entropy geometry and represents spiral galaxies well. It is also known that the virial mass of such a galaxy can be approximately determined from the entropy of its central supermassive black hole. But over time the black hole must accrete mass, and therefore the overall galactic entropy must increase. From the associated entropic Euler-Lagrange equation (forming the basis of the Principle of Least Exertion, and also enabling the application of Nöther’s theorem) we show that the galactic entropy production is a conserved quantity, and we derive an appropriate expression for the relativistic entropic Hamiltonian of an idealised spiral galaxy. We generalise Onsager’s celebrated expression for entropy production and demonstrate that galactic entropy production has two parts, one many orders of magnitude larger than the other, and where the smaller is comparable to the Hawking radiation of the central supermassive black hole. We conclude that galaxies cannot be isolated, since even idealised spiral galaxies have non-zero entropy production.

Agriculture contributes towards South African economy, but this sector is highly vulnerable to risks imposed by climate change. Smallholder maize farmers are specifically susceptible to climate change impacts. Maize crop plays a crucial role in the country's food security as it is considered a stable food for households and source of feed for livestock. The study aimed to analyze the socio-economic factors influencing smallholder maize farmers’ willingness to adopt climate-smart agriculture. It was conducted in three different areas due to their specific agro-ecological zones. Multipurpose research design was used to gather data, and multistage random sampling to choose the study areas. Subsequently, 209 purposively selected farmers were interviewed face-to-face using structured questionnaires and focus discussion groups. Descriptive statistics and Double-hurdle regression model were used to analyze the data. Descriptive results indicated that 81%, 67%, and 63% farmers were willing to adopt CSA in Ga-Makanye, Gabaza, and Giyani, respectively. Empirical results from the first and second hurdles of the regression analysis showed that farmers’ education, crop diversification, information about CSA positively influenced the decision to adopt CSA while household size and agricultural experience negatively influenced the decision to adopt CSA. It is recommended that the Department of Agriculture, Land Reform, and Rural Development should provide CSA workshops and educational programs to farmers to enhance their knowledge and decision-making processes regarding adaptation strategies.

Hyperspectral small target detection (HSTD) is a promising pixel-level detection task. However, due to the low contrast and imbalance number between the target and background spatially and high dimensions spectrally, it is a challenging one. To address these issues, this work proposes a representation learning-based graph and generative network for hyperspectral small target detection. The model builds a fusion network through frequency representation for HSTD, where the novel architecture incorporates irregular topological data and the spatial-spectral feature to improve its representation ability. Firstly, a graph convolutional network (GCN) module better models the non-local topological relationship between samples to represent the hyperspectral scene’s underlying data structure. The mini-batch-training pattern of the GCN decreases the high computational cost of building an adjacency matrix for high-dimensional data sets. In parallel, the generative model enhances the differentiation reconstruction and the deep feature representation ability with respect to the target spectral signature. Finally, a fusion module compensates for the extracted different types of HS features and integrates their complementary merits for hyperspectral data interpretation while increasing detection and background suppression capabilities. Experiments on different hyperspectral data sets demonstrate the advantages of the proposed architecture.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

Global warming and the associated increasing frequency of heatwaves are on the rise leading to numerous health complications. Diabetic patients are more vulnerable to heat exposure than healthy individuals, owing to their impaired sweating ability, however, little is known about how heat exposure may impact the function of skin cells, commonly keratinocytes. Our recent report provided the first proof-of-concept revealing that the metabolic composition of sweat EVs is associated with metabolic changes in healthy individuals and type 2 diabetes patients. Given this and the shared cellular proprieties of eccrine sweat glands with keratinocytes, we questioned whether the metabolic changes in sweat EVs may mirror the responses of keratinocytes upon heat exposure. To this, we exposed HaCat, which were maintained in low (mimicking healthy condition) and high glucose (mimicking diabetes condition) to acute (90 min), chronic (48 h), and repetitive heat exposure at 40 ⁰C. Through conducting a set of experiments including a targeted metabolomics approach, Greiss assay, western blotting analysis, and electron microscopy studies. The data demonstrate that heat exposure results in substantial changes of metabolite levels belonging to amino acids, pyrimidine metabolism, and glycolysis pathways in high glucose maintained HaCat cells when compared to those noted in low glucose condition. Exploring the molecular mechanisms through which heat exposure may impact the metabolic composition in keratinocytes, our discoveries highlight nitric oxide (NO) as a novel biomarker that the level is correlated with heat duration and frequency. Furthermore, data reveal that the HSP-70 protein levels and mitochondrial morphology are consequently altered. This study provides evidence of shared metabolic alterations in keratinocytes and sweat EVs collected from clinical study and proposes, for the first time, NO as a novel biomarker for monitoring changes in health and diabetes upon heat exposure.

An exposition of entropy applications to highlight some potential entropic applications to artificial intelligence and knowledge transfer. Entropy is a basic idea in artificial intelligence that is applied to many different tasks, such as reinforcement learning, data compression, and decision-making. By quantifying uncertainty and information content, it helps artificial intelligence models provide predictions and decisions that are well-informed. Therefore, this paper shines on spotlighting the significance of entropy to attract the attention of artificial intelligence research community to entropy as a powerful tool to advance artificial intelligence.The significance of knowledge transfer (KT), particularly intergenerational knowledge transfer (IGT), in knowledge management is also covered in this paper. To quantify the complexity of knowledge distribution inside an organisation and assess the efficacy of knowledge transfer (KT) initiatives, the notion of knowledge entropy (KE) is presented. Additionally, the KT model—which is based on the conceptions of tacitness and information content—is introduced. It combines personalisation and codification methodologies. Future research directions are offered alongside a few difficult open problems.

Cellular Nonlinear Networks (CNN) are a concept introduced in 1988 by Leon Chua and Lin Yang as a bio-inspired architecture, capable of massively parallel computation. Later on, CNN have been enhanced by incorporating designs that incorporate memristors to profit from their processing and memory capabilities. In addition, Stochastic Computing (SC) can be used to optimize the quantity of required processing elements; thus it provides a lightweight approximate computing framework, quite accurate and effective, though. In this work, we propose utilization of SC in designing and implementing a memristor-based CNN. As a proof of the proposed concept, an example of application is presented. This application combines Matlab and a FPGA in order to create the CNN. The implemented CNN has then been used to perform three different real-time applications on a 512x512 gray-scale and a 768x512 color image: storage of the image, edge detection, and image sharpening. It has to be pointed out that the same CNN has been used for the three different tasks, with the sole change of some programmable parameters. Results show an excellent capability with significant accompanying advantages, like the low number of needed elements further allowing for a low cost FPGA-based system implementation, something confirming the system’s ability for real time operation.

In recent years, the field of deep learning achieved considerable success in pattern recognition, image segmentation and may other classification fields. There are a lot of studies and practical applications of deep learning on images, video or text classification. In this study, we suggest a method for changing the architecture of the most performing CNN models with the aim of designing new models to be used as stand-alone networks or as a component of an ensemble. We propose to replace each activation layer of a CNN (usually a ReLu layer) by a different activation function stochastically drawn from a set of activation functions: in this way the resulting CNN has a different set of activation function layers.

This paper presents a comparative study of heat transfer performance of lattice structured heat sinks. 20 different unit cells were chosen and heat sinks were modelled in nTop with constant unit cell size. Al 6061 alloy was chosen for analysis due to its good thermal conductivity, low weight, low cost, and high strength. Steady state thermal analysis was performed using ANSYS with constant input parameters for all samples. Heat flux and temperature distribution within the heat sinks were analysed. The study aims to provide a comprehensive understanding of the thermal performance of lattice heat sink designs.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

Synergy, emerges from synchronized reciprocal positive feedback loops between a network of diverse actors. For this process to proceed, compatible information from different sources synchronically coordinates the actions of the actors resulting in a nonlinear increase in the useful work or potential energy the system can manage. In contrast noise is produced when incompatible information is mixed. This synergy produced from the coordination of different agents achieves non-linear gains in free energy and in information (negentropy) that are greater than the sum of the parts. The final product of new synergies is an increase in individual autonomy of an organism that achieves increased emancipation from the environment with increases in productivity, efficiency, capacity for flexibility, self-regulation and self-control of behavior through a synchronized division of ever more specialized labor. Examples that provide quantitative data for this phenomenon are presented. Results show that increases in free energy density require decreases in entropy density. This is proposed as a law of thermodynamics.

The environment significantly impacts the life of bees and their feeding. This study aimed to investigate bee foraging using melissopalynological analysis and DNA metabarcoding in ​​intensive farming, reserved, and urbanized areas. The highest alpha diversity was observed in the reserved and in the intensive farming areas. The urbanized area has less diversity. In the intensive farming area predominated: Sinapis, Helianthus, and Fagopyrum; in the reserved area: Melilotus, Helianthus, and Brassica. In the urbanized area garden plants: radish (Raphanus sativus) and cucumber (Cucumis hystrix) and agricultural plants: soybean (Glycine max) and melon (Cucumis melo) were often found. The most significant agreement was between the rbcL and the melissopalynological analysis. The ITS2 revealed equal matches with both rbcL and melissopalynology but this marker missed or underestimated some genera. Trifolium pretense and Brassica nigra, were identified simultaneously by three analyses. Species Convolvulus arvensis, Melilotus officinalis, Echium vulgare, Brassica rapa, Helianthus divaricatus, and Onobrychis viciifolia were found in all ecological areas. Imperfect databases put some limits for identification of some taxa using metabarcoding. Further research and expansion of plant databases is needed. Studying the food preferences of bees in different environmental conditions and landscapes is necessary to develop measures to preserve their population.

Experimental recordings of the collective activity of interacting spiking neurons exhibit random behavior and memory effects, thus the stochastic process modeling the spiking activity is expected to show some degree of time irreversibility. We use the thermodynamic formalism to build a framework, in the context of spike train statistics, to quantify the degree of irreversibility of any parametric maximum entropy measure under arbitrary constraints, and provide an explicit formula for the information entropy production of the inferred Markov maximum entropy process. We provide examples to illustrate our results and discuss the importance of time irreversibility for modeling the spike train statistics.

Energy harvesting is an emerging topic recently. This harvested energy is used to operate wireless sensors for different industrial monitoring and automation. To maximize the harvested energy in spinning systems, the harvester should vibrate at resonance for different spinning frequencies which can be achieved by active fitting. In this research, a novel methodology was developed by actively customizing the length of vibrating element beam to manipulate its natural frequency according to the spinning frequency. Different models were investigated numerically and experimentally to verify the proposed methodology. COMSOL Multiphysics software V5.1 was used to develop the numerical model, then and tip deformation and voltage difference results were benchmarked. The numerical model was verified experimentally by attaching a piezoelectric MIDE PPA 1021 which its vibrating length was varied by changing the supporting length from 0 mm to 12 mm to a spinning object having variable frequency from 0-200 Hz. It is found that the MIDE PPA 1021 beam vibrated at its resonance throughout the specified spinning frequencies. The proposed harvester can be applied in battery-free sensors being used in automotives, wind-mills blades, and rotating machinery.

The aim of the present trial was to evaluate the growth performance of buffalo calves fed diets characterized by different forage/concentrate ratio with or without the Saccharomyces Cerevisiae supplementation (CBS 493.94, Yea-Sacc®). Twenty-four male buffalo calves (mean age 145.1 ± 16.1 days; mean weight 108.0 ± 18.7) were assigned randomly to 4 groups, homogeneous for age, fed four different diets: diet 1 F:C ratio 50:50; diet 2 F:C ratio 30:70; diet 3 F:C ratio 50:50 + Yea-Sacc® and diet 4 F:C ratio 30:70 + Yea-Sacc®. Buffalo calves were individually weighted before the start of the experiment and the data were used as a covariate, monthly until the end of the trial. Dry matter intake (DMI), daily weight gain (DWG) and feed conversion ratio (FCR) were calculated. The differences in diets’ composition significantly (p

Complex systems can be described as the network of interactions between their components. In directed networks, information, energy and matter flow in dominant directions. Undirected networks, on the other hand, cannot easily capture these asymmetries. The local flow of information depends on the node spin, which is a function of the number of incoming and outgoing links attached to it. And yet, how the heterogeneous association between in-degree and out-degree constraints global dynamics remains poorly understood. Here, we develop a new theoretical model to study the relationship between node directionality and global flow dynamics. Our computational analysis of random and scale-free directed networks indicates that structural diversity constrains the dimensionality of reachable dynamical space. These results suggest how local directionality might be an universal driver of global dynamics in many systems, from social networks, to technological systems to the connectome.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

Graph neural networks (GNNs) build on the success of deep learning models by extending them for use in graph spaces. Transfer learning has proven extremely successful for traditional deep learning problems: resulting in faster training and improved performance. Despite the increasing interest in GNNs and their use cases, there is little research on their transferability. This research demonstrates that transfer learning is effective with GNNs, and describes how source tasks and the choice of GNN impact the ability to learn generalisable knowledge. We perform experiments using real-world and synthetic data within the contexts of node classification and graph classification. To this end, we also provide a general methodology for transfer learning experimentation and present a novel algorithm for generating synthetic graph classification tasks. We compare the performance of GCN, GraphSAGE and GIN across both the synthetic and real-world datasets. Our results demonstrate empirically that GNNs with inductive operations yield statistically significantly improved transfer. Further we show that similarity in community structure between source and target tasks support statistically significant improvements in transfer over and above the use of only the node attributes.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

A novel approach is developed to improve the convergence of Physics-Informed Neural Networks (PINNs), aiming to employ them as real-time computational models within the framework of the digital twin for manufacturing processes. This method entails the weighting of physical equations, boundary conditions, and initial conditions to ensure their comparable magnitudes, with power being the chosen quantity in this study. The approach is applied to thermal problems, which are crucial for predicting manufacturing part defects. Different configurations, including complex boundary conditions and complex physics, were tested to assess the model’s robustness. The W-PINN demonstrates good predictions and strong stability compared to the classical PINN.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

As known all physical properties of solids are described well by the system of quantum linear harmonic oscillators. It is shown in the present paper that the system consisting of classical linear harmonic oscillators having temperature dependent masses or (and) frequencies has the same partition function as the system consisting of quantum linear harmonic oscillators having temperature independent masses and frequencies while the means of the square displacements of the positions of the oscillators from their mean positions for the system consisting of classical linear harmonic oscillators having: the temperature dependent masses; temperature dependent frequencies; and temperature dependent masses and frequencies differ from each other and from that of the system consisting of quantum linear harmonic oscillators, and hence, the system consisting of classical linear harmonic oscillators describes well the thermodynamic properties of the system consisting of quantum linear harmonic oscillators and solids.

Autonomous navigation in dynamic environments poses a significant challenge in the field of ro-botics with the primary goals of ensuring both smooth and safe movement. This study introduces control strategy based on an Adaptive Neuro-Fuzzy Inference System (ANFIS) to enhance au-tonomous robot navigation in dynamic environments, emphasizing on collision-free path plan-ning. This strategy employs, a path planning technique to develop a trajectory that allows the ro-bot to navigate smoothly while avoiding collisions with both static and dynamic obstacles. The developed control system incorporates four ANFIS controllers: two are tasked with guiding the robot toward its end point, and the other two are activated for obstacle avoidance. The experi-mental setup conducted in CoppeliaSim involves a mobile robot equipped with ultrasonic sensors navigating in an environment with static and dynamic obstacles. Simulation experiments are conducted to demonstrate the model's capability in ensuring collision-free navigation, employing a path planning algorithm to ascertain the shortest route to the target destination. The simulation results highlight the superiority of the ANFIS-based approach over conventional methods, partic-ularly in terms of computational efficiency and navigational smoothness.

The production of recombinant enzymes, mainly used for obtaining pure and functional target molecules, holds significant importance in modern biotechnology. This study aimed to produce recombinant α-amylases (Amy3500 and Amy1974), derived from B. amyloliquefaciens MDC1974 and B. subtilis MDC3500 respectively, using the pBE-S shuttle vector, and to characterize them. Both α-amylase genes were molecularly cloned into the E. coli/B. subtilis pBE-S shuttle vector, both with (Amy1974sig and Amy3500sig) and without their own signal peptides (Amy1974 and Amy3500), along with a signal peptide originating from the plasmid, and tested in flask fermentations. For recombinant Amy3500, the amylase variants resulted in similar levels of volumetric activity (700-750 U/mL). In contrast, the expression of Amy1974 nearly doubled compared to Amy1974sig with double signal peptides, reaching 2000 U/mL. The SDS-PAGE estimated the molecular weight of Amy1974 α-amylase to be 54.6 kDa, which was in accordance with the theoretical molecular mass calculations. However, the estimated molecular weight of Amy3500 amylase was significantly reduced when exiting the producer cells. Ca2+ had no significant activating effect on the activities of Amy1974 amylase and Amy3500 amylase, likely due to its tight binding to the protein scaffold. Both enzymes exhibited broad activity peaks between 45-70°C, with a maximum at 65°C. The Amy1974 and Amy3500 α-amylases demonstrated broad pH optima and pH-dependent thermostability, with optimum pH values at 6.5 and 5.8, and thermal stability peaks at pH 7.6 and 5.9, respectively. Both α-amylases displayed high relative activity against various starches, including corn amylopectin and potato amylose, while showing comparatively lower activity towards cyclodextrins. The Amy1974 amylase converts starch to dextrins of varying lengths, whereas Amy3500 almost entirely converts starch into glucose.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

Fire is a serious security threat that can lead to casualties, property damage, and environmental damage. However, despite the availability of object detection algorithms, challenges persist in detecting fires and smoke. These challenges include slow convergence speed, poor performance in detecting small targets, and high computational cost limiting deployments. In this paper, Fire smoke and human detection based on ConvNeXt and Mixed encoder (FCM-DETR), an end-to-end object detection algorithm based on Deformable DETR, is proposed. Firstly, we introduce ConvNeXt to take the place of Resnet, which greatly reduces the amount of computation and improves the ability to extract irregular flame features. Secondly, to effectively process multi-scale features, the original encoder is decoupled into two modules. Then Mixed encoder, an innovative encoder structure, is proposed, resulting in excellent performance of multi-scale fire and smoke features fusion. What can’t be overlooked is that the encoder block is compatible with any DETR-based models. Finally, the convergence speed is accelerated and the mean of average precision is improved by applying a novel loss function called Powerful IoU v2. The experimental results indicate that our model achieves the best detection accuracy compared to other models, with mAP reaching 66.7%, mAPs and Accuracyfire achieving impressive 50.2% and 98.05%, respectively.

We study the brain segmentation by dividing the brain into multiple tissues. Given possible brain segmentation by deep, machine learning can be efficiently exploited to expedite the segmentation process in the clinical practice. To accomplish segmentation process, a MRI and tissues transfer using generative adversarial networks is proposed. Given the better result, we propose the transfer model using GAN. For the case of the brain tissues, white matter (WM), gray matter (GM) and cerebrospinal fluid (CSF) are segmented. Empirical results show that this proposed model significantly improved segmentation results compared to the stat-of-the-art results. Furthermore, a dice coefficient (DC) metric is used to evaluate the model performance.

This paper proposes a non-extensive entropy econometric technique to predict energy efficiency at province (NUT-2) level based on imperfect knowledge of the national overall efficiency in the sectors of industry, transport, households and services. The model is applied to the polish case. As acknowledged in recent literature, non-extensive entropy model should remain a valuable device for econometric modelling even in the case of low frequency series since outputs provided by the Gibbs-Shannon entropy approach correspond to the Tsallis entropy limiting case of the Gaussian law when the Tsallis q-parameter converges to unity. Therefore, we set up a q-Tsallis-Kullback-Leibler entropy criterion function with a priori consistency moment and model data constraints, including province energy intensity (known with uncertainty), regional climate differentiation and regular conditions. The model outputs continue to conform to empirical expectations. In spite of the close to unity q-Tsallis parameter, this Tsallis related approach reflects higher stability for parameter computation in comparison with the Shannon-Gibbs entropy econometrics technique. The proposed technique can be applied in different EU countries and elsewhere for example in the context of experimental official statistics.

Galectin-3 (Gal-3) is a lectin associated with fibrosis and inflammation, and increased circulating concentrations are considered a risk factor for atrial fibrillation (AF) in humans. This retrospective study aimed to evaluate the serum concentration of Gal-3 in dogs with cardiac disease, both with and without AF. Dogs with AF associated with congenital and acquired heart diseases were selected, while clinically healthy dogs and dogs with heart diseases but without AF served as controls. We statistically compared the serum concentration of Gal-3, assessed using a commercial canine-specific ELISA kit, among healthy dogs and dogs with heart disease with and without AF. Additionally, associations between Gal-3 and clinical and echocardiographic variables were evaluated. A total of 80 dogs were included, of which 17/80 (21.2%) were clinically healthy and 63/80 (78.8%) had heart disease, with 30/63 (47.6%) having AF. No significant difference in Gal-3 concentration was found between healthy dogs (3.90 ± 0.38 ng/mL) and dogs with heart disease, either with or without AF (3.45 ± 0.28 ng/mL, P=0.226 and 4.46 ± 0.27 ng/mL, P=0.286, respectively). Gal-3 showed a significant positive correlation with age (r=0.46, P < 0.001). The results of this study suggest that Gal-3 does not have predictive value for the development of AF in dogs, but it is associated with advanced age.

The toxic cadmium (Cd) poses a serious threat to plant growth and human health. Populus euphratica CPK21 has previously been shown to attenuate Cd toxicity by reducing Cd accumulation, enhancing antioxidant defense and improving water balance in transgenic Arabidopsis. Here, we confirmed a protein-protein interaction between PeCPK21 and AtNF-YC3 by yeast two-hybrid, HaloTag pull-down and bimolecular fluorescence complementation assays. AtNF-YC3 was induced by Cd and strongly expressed in PeCPK21-overexpressed plants. Overexpression of AtNF-YC3 in Arabidopsis reduced salt inhibition of root length, fresh weight and membrane stability under Cd stress conditions (100 µM, 7 d), suggesting that AtNF-YC3 appears to contribute to the improvement of Cd stress tolerance. AtNF-YC3 improved Cd tolerance by limiting Cd uptake and accumulation, activating antioxidant enzymes, and reducing H2O2 production under Cd stress. We conclude that PeCPK21 interacts with AtNF-YC3 to limit Cd accumulation, enhance the ROS scavenging system, and thereby positively regulate plant adaptation to Cd environments. This study highlights the interaction between PeCPK21 and AtNF-YC3 under Cd stress conditions, which can be utilized to improve Cd tolerance in higher plants.

Despite energy-related financial concerns and the growing demand for sustainability, many energy efficiency measures are not being implemented in industrial practice. There are a number of reasons for this, including a lack of knowledge about energy efficiency potentials and the assessment of energy savings as well as the high workloads of employees. This article describes the systematic development of an expert system, which offers a chance to overcome these obstacles and contribute significantly to increasing the energy efficiency of production machines. The system employs data-driven regression models to identify inefficient parameter settings, calculate achievable energy savings, and prioritize actions based on a fuzzy rule base. Proposed measures are first applied to an analytical real-time simulation model of a production machine to verify that constraints required for the specified product quality are met. This provides the machine operator with the expert means to apply proposed energy efficiency measures to the physical entity. We demonstrate the development and application of the system for a throughput parts cleaning machine in the metalworking industry.

Maximum entropy production principle (MEPP) has been formulated in the mid-twentieth century, and today it has acquired the status of an important principle of science, which is extremely effective in considering various non-equilibrium problems. In this study, for the first time, definition of life is based on an easily measurable physical quantity that is entropy production. Life and evolution are discussed from the point of view of MEPP and the Universe, but not a human

Several optimization models of irreversible reverse cycle machines have been developed based on different optimization criteria in the literature, most of them using linear heat transfer laws at the source and sink. This raises the issue how close to actual operation conditions they are, since the heat transfer law on the phase-change processes is dependent on ΔT3. This paper addresses this issue by proposing a general model for study and optimization of thermal machines with two heat reservoirs applied to a Carnot-like refrigerator, with non-linear heat transfer laws and internal and external irreversibility. The optimization was performed using First and Second Law of Thermodynamics and Lagrange multipliers method. Thus, several constraints were imposed to the system, also different objective functions were considered, allowing finding the optimum operating conditions, as well as the limited variation ranges of the system parameters. Results show that the nature of the heat transfer laws affects the optimum values of system parameters for obtaining maximum performances and also their magnitude. Sensitivity studies with respect to system several parameters are presented. The results contribute to the understanding of the system limits in operation under different constraints and allow choosing the most convenient variables in given circumstances.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

Adaptable or adapted? Whether it is a question of physical, biological or even economic systems, this problem arises when all these systems are the location of matter and energy conversion. To this interdisciplinary question we propose a theoretical framework based on the two principles of thermodynamics. Considering a finite time linear thermodynamic approach, we show that non-equilibrium systems operating in quasi-static regime are quite deterministic as long as boundary conditions are correctly defined. The Novikov-Curzon-Ahlborn approach [1,2] applied to non-endoreversible systems then makes it possible to precisely determine the conditions for obtaining characteristic operating points. As a result, power maximization principle (MPP), entropy minimization principle(mEP), efficiency maximization, or waste minimization states are only specific modalities of system operation. We show that boundary conditions play a major role in defining operating points because they define the intensity of the feedback that ultimately characterizes the operation. Armed with these thermodynamic foundations, we show that the intrinsically most efficient systems are also the most constrained in terms of controlling the entropy and dissipation production. In particular, we show that the best figure of merit necessarily leads to a vanishing production of power. On the other hand, a class of systems emerges which, although they do not offer extreme efficiency or power, have a wide range of use and therefore marked robustness. It therefore appears that the number of degrees of freedom of the system leads to an optimization of the allocation of entropy production.

Demand for development of the convergence industry, research studies on electrical conductivity, thermal characteristics, semiconductors, motors, and batteries using special materials have come to the fore. Meanwhile, molybdenum (Mo) exhibits relatively small inorganic qualities, and the thermal conductivity rate is applied to various fields. In this study, in-depth characteristics were considered regarding the concentration of thermal characteristics, IR car terminal characteristics, and IR ve-hicles. This study calculated each phase temperature of the molybdenum sputtered specimens in the steady state according to the heat transfer theory. When the molybdenum-sputtered fabric’s metal layer pointed to the outside air, the heat transfer rate (Q) was high at 5748.3W, In contrast, if the molybdenum sputtered film’s metal layer of the pointed toward the heat source, the heat transfer rate (Q) was low at 187.1W. As a result of measuring the IR transmittance, the infrared transmit-tance of the molybdenum sputtering-treated sample was significantly reduced compared to the untreated sample. In the case of untreated samples, the transmittance ranged from 92.7 to 42.0%. When only the cross part was treated with molybdenum sputtering and the molybdenum surface was directed toward the IR irradiator, the IR transmittance was 66.8~0.7%. It is believed that the molybdenum sputtering polyamide samples produced in this study can be applied to multifunc-tional military wear, biosignal detection sensors, semiconductor products, batteries, etc., by utilizing excellent electrical properties, stealth functions, IR blocking properties, and lightness for infrared thermal imaging detectors.

Membrane fouling caused by many direct and indirect triggering factors has become an obstacle to the application of membrane bioreactor (MBR). The nonlinear relationship between those factors is subject to complex causality or affiliation, which is difficult to clarify for the diagnosis of membrane fouling. To solve this problem, this paper proposes a compressible diagnosis model (CDM) based on transfer entropy to facilitate the fault diagnosis of the root cause for membrane fouling. Firstly, a framework of CDM between membrane fouling and causal variables is built based on a feature extraction algorithm and mechanism analysis. The framework can identify fault transfer scenarios following the changes in operating conditions. Secondly, the fault transfer topology of CDM based on transfer entropy is constructed to describe the causal relationship between variables dynamically. Thirdly, an information compressible strategy is designed to simplify the fault transfer topology. This strategy can eliminate the repetitious affiliation relationship, which contributes to the root causal variables speedily and accurately. Finally, the effectiveness of the proposed CDM is verified by the measured data from an actual MBR.

We explored the dynamics of the two interacting information systems. We show that for the Markovian marginal systems the driving force for information dynamics is determined by both the information landscape and information flux. While the information landscape can be used to construct the driving force to describe the equilibrium time reversible information system dynamics, the information flux can be used to describe the nonequilibrium time-irreversible behaviours of the information system dynamics. The information flux explicitly breaks the detailed balance and is a direct measure of the degree of the nonequilibriumness or time irreversibility. We further demonstrate that the mutual information rate between the two subsystems can be decomposed into the equilibrium time-reversible and nonequilibrium time-irreversible parts respectively. This decomposition of the mutual information rate (MIR) corresponds to the information landscape-flux decomposition explicitly when the two subsystems behave as Markov chains. Finally, we uncover the intimate relationship between the nonequilibrium thermodynamics in terms of the entropy production rates and the time-irreversible part of the mutual information rate. We found that this relationship and MIR decomposition still hold for the more general stationary and ergodic cases. We demonstrate the above features with two examples of the bivariate Markov chains.

Seed potato treatment is vital for plant protection, yield enhancement, and product quality. In the conducted research, the plant biostimulator Supporter was applied to evaluate its impact on potato yields. Field studies were conducted in Northeastern, Northwestern, Western, and Southwest Poland from 2015 to 2017, using a randomized complete block design with a split-plot arrangement. The use of seed treatment technology with the Supporter product resulted in increased overall and commercial potato yields and improved yield tuber structure compared to traditional cultivation methods without tuber treatment before planting. Conclusion: The application of the plant biostimulator Supporter in seed potato treatment technology brings significant benefits, including, increased potato yield and improved yield structure. The cultivation location significantly influences potato yield and tuber structure. Understanding these differences can aid in better adapting cultivation practices and selecting varieties to specific local conditions, potentially leading to increased potato crop productivity. In terms of efficiency and yield quality, further research into its application in agricultural practice is recommended, which may contribute to further increasing potato production efficiency and quality. Developing more ecological and efficient farming practices can help meet society's growing food needs.

Expansins are cell wall (CW) proteins that mediate the CW loosening and regulate salt tolerance in a positive or negative way. The transcription of Populus trichocarpa expansin A6 (PtEXPA6) was downregulated upon prolonged duration of salt stress (48 h) after a transient increase induced by NaCl (100 mM). The role of PtEXPA6 in salt tolerance was determined by transferring the PtEXPA6 gene into the hybrid species Populus alba × P. tremula var. glandulosa clone 84K (84K) and Populus tremula × P. alba INRA '717-1B4' (717-1B4). The PtEXPA6-transgenic poplars of 84K and 717-1B4 showed a greater reduction in photosynthesis, stem height and diameter growth under salt stress and a reduced capacity for ROS scavenging by antioxidant enzymes, which is associated with excessive Na+ accumulation in roots and shoots. NMT flux recordings showed that the radial translocation of Na+ salt into the root xylem and real-time Na+ translocation from roots to leaves were greater in PtEXPA6-transgenic poplars than in wild-type poplars. Analysis of comparative contractility and comparative extensibility of intact root tips indicated that PtEXPA6 increased the CW loosening in the transgenic poplars of 84K and 717-1B4. Noteworthy, the PtEXPA6-promoted CW loosening was shown to facilitate radial and longitudinal transport of Na+ in transgenic poplars. We conclude that overexpression of PtEXPA6 leads to CW loosening that facilitates radial translocation of Na+ into the root xylem and subsequent Na+ translocation from roots to leaves, resulting in excessive Na+ accumulation and consequently reduced salt tolerance in transgenic poplars.

The automotive market is very competitive and presents a demand for the consistent improvement of the used technologies and reduction of the product cost and dimensions with each product model iteration. Hence, it is important to have access to well-defined reference designs of high quality products, in order to evaluate the new ideas and technologies. This paper provides the readers with a numerical model of such a high quality product, i.e., the IPMSM type traction motor from the 4th generation of the Toyota Prius hybrid transaxle. In the introductory section, the brief history of the Prius model is given together with the references to the reverse engineering reports. Afterwards, the machine dimensions, material properties and winding configuration are described. Then, the model is validated with the torque measurements at constant speed. In the next chapters the simulation results are presented and the numerical source data are supplied to the reader. Finally, the design philosophy of the Toyota drive is briefly discussed in comparison with the BMWi3 drive and the results are concluded in the last section.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

Most astrophysicists today believe that the present universe was produced in a big bang. This article explores the big cycle of matter and energy in the universe, with the big bang as an important part of the cycle.The authors approve of the idea that the universe is gravitationally closed. That is, its average density is higher than the critical value. All the matter and radiation cannot fly out the closed universe.The 3k background radiation is a vast heat ocean in the closed universe, stable and eternal. It is not the afterglow of the thermal radiation of the decoupled fire ball, 380,000 years after the big bang, as many people believed so far. The big bang and the following big expansion drove the matter of more than 2×10¹² galaxies to the remote space. Their potential energies become higher and higher, while their huge kinetic energies that they derived from the big bang become smaller and smaller until drop down to zero. The galaxies will then return back one after another, passing the central region of the universe with tremendously great kinetic energies. They of course cannot all return back directly to their start point of the big bang and restore to the state of the original cosmic core. They will rush to pass the central region and fly to the other sides of the universe, and shuttle around the central part ceaselessly. From the big bang to the following expansion, to the numerous galaxies, to the more than 2×10²³ stars, and to the stars releasing huge nuclear energy due to their internal nuclear fusion each for about 10¹⁰ years, all these enormous processes are irreversible, resulting in enormous increase in entropy. These processes produce large amount of light and other radiations and pour them into the extremely vast heat ocean. These light and other radiations will also be shuttling ceaselessly in the vast heat ocean until, by their interaction with the rare dusts in the galaxies, they mingle into the 3K thermal radiation of the heat ocean. In all the galaxies, there are various black holes. Every black hole, since its birth, ceaselessly extracts the matter and radiation that approach it, and gets larger. In the above mentioned shuttling of all the galaxies, numerous stars and black holes in these galaxies have many chances to approach even meet each other. A black hole can annex other celestial bodies that it meets, including annex other black holes. All these processes carry on and on ceaselessly, resulting in the matter of these celestial bodies to concentrate again and again. The number of all the celestial bodies including the black holes reduces ceaselessly, and the mass of the survived black holes become larger, and their shuttling amplitudes become shorter. The larger black holes and the shorter amplitudes result in the rate of concentration of mass to be faster. Eventually, all the matter in the universe will be concentrated to form a tremendously large central black hole. The central black hole has an astonishingly large Schwarzschild sphere, absorbing the thermal radiation from the vast heat ocean very rapidly and ceaselessly until some threshold value of its internal energy is exceeded, and a new big bang breaks out. The black holes provide a way in the Universe to re-concentrate matter and energy again. Black holes are Maxwell’s demons in the Nature.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

This study aimed to solve the problems of sealing and tearing failure of packer’s rubber cylinders during CO2 downhole injection. Using the simulation software, Comsol, a rubber cylinder model in a supercritical CO2 (SC-CO2) environment was established. The thermal analogy method was used to simulate the CO2 diffusion and rubber cylinder swelling process, thus we analyzed the deformation and stress of the rubber cylinder caused by temperature, pressure and CO2 as swelling agent. Results showed that, in the SC-CO2 environment, under the influence of CO2 diffusion and the consequent swelling, the rubber cylinder body is prone to large deformation, and the maximum shear stress is significantly increased, leading to shear failure of the rubber cylinder. The reduction of the initial seating pressure can alleviate the impact of deformation, whereas the reduction of the maximum contact pressure could cause the rubber cylinder to lose its seal. We also analyzed the change rules between various factors and the maximum contact pressure of the rubber cylinder, which provides a theoretical basis and technical support for improving the sealing performance of the packer’s rubber cylinder in the SC-CO2 environment.

Land cover segmentation, a fundamental task within the domain of remote sensing, boasts a broad spectrum of application potential. In this article, we focus on the land cover segmentation tasks and complete the following research work: Firstly, to address the issues of uneven distribution of foreground and background and significant differences in target scales in remote sensing images, we propose a decoder called MDCFD based on multi-dilation rate convolution fusion. The decoder utilizes dilated convolution to expand the receptive field, enhancing the model's ability to capture global features and thus improving the model's ability to distinguish between foreground and background. Meanwhile, we design a multi-dilation rate convolution fusion module (MDCFM), which fuses the outputs of different dilation rate convolution layers. Secondly, aiming at the problems of diverse scenes, significant differences between categories, and many background interferences in remote sensing images, we propose a hybrid attention module called LKSHAM based on large kernel convolution. This module combines spatial attention and channel attention mechanisms and combines the two attention modules in series. By introducing large kernel convolution, the model's ability to extract contextual information is improved. At the same time, we adopt a strategy of decomposing large kernel convolution into multiple depthwise convolutions to reduce computational complexity. The improved network models designed by this paper can achieve an improvement of over 1.1% in the mIoU metric on segmentation tasks on the Potsdam and Vaihingen datasets.

Abstract: With the growing integration of the Internet of Things (IoT) in smart buildings, it is crucial to ensure the precise implementation and operation of wireless sensor networks (WSNs). This paper aims to study the implementation aspect of Wireless Sensor Networks (WSNs) in a commercial multi-story building, specifically addressing the difficulty of dealing with variable environmental conditions on each floor. This research addresses the disparity between simulated situations and actual deployments, offering valuable insights that have the potential to signifi-cantly improve the efficiency and responsiveness of building management systems. We obtain real-time sensor data to analyze and evaluate the system’s performance. Our investigation is grounded in the growing importance of incorporating WSNs into buildings to create intelligent environments. By leveraging the capabilities of Contiki operating system, this study employs a specialized simulator to generate simulated data, allowing for a comparison between real-world and simulated scenarios. We provide an in-depth analysis to scrutinize the disparities and commonalities between the datasets obtained from real-world deployments and simulated en-vironments. We highlight the necessity of precise simulation to validate real-life sensor data, shedding light on the challenges and opportunities associated with implementing WSNs in in-telligent buildings. Results obtained show the significance of accurate simulation models for re-liable data representation, providing a roadmap for further developments in the integration of WSNs into intelligent building scenarios. The findings highlight the potential for optimizing living and working conditions based on the real-time monitoring of critical environmental pa-rameters. This includes insights into temperature, humidity, and light intensity, offering oppor-tunities for enhanced comfort and efficiency in intelligent environments.

Despite the remarkable success of Carnot’s heat engine cycle in founding the discipline of thermodynamics two centuries ago, false viewpoints of his use of the caloric theory in the cycle still linger, limiting his legacy. An action revision of the Carnot cycle can correct this, showing that the heat flow powering external mechanical work is compensated internally with configurational changes in the thermodynamic or Gibbs potential of the working fluid, differing in each stage of the cycle quantified by Carnot as caloric. Action (@) is a property of state having the same physical dimensions as angular momentum (mrv=mr2ω). However, this property is scalar rather than vectorial, including a dimensionless phase angle (@=mr2ωδφ). We have recently confirmed with atmospheric gases that their entropy is a logarithmic function of the relative vibrational, rotational and translational action ratios with Planck’s quantum of action ħ. The Carnot principle shows that the maximum rate of work (puissance motrice) possible from the reversible cycle is controlled by the difference in temperature of the hot source and the cold sink, the colder the better. This temperature difference between the source and the sink also controls the isothermal variations of the Gibbs potential of the working fluid, that Carnot identified as reversible temperature-dependent but unequal exchanges in caloric. Importantly, the engine’s inertia ensures that heat from work performed adiabatically in the expansion phase is all restored to the working fluid during the adiabatic recompression, less the net work performed. This allows both the energy and the thermodynamic potential to return to the same values at the beginning of each cycle, a point strongly emphasized by Carnot. Our action revision equates Carnot’s calorique, or the non-sensible heat later described by Clausius as ‘work-heat’ exclusively to negative Gibbs energy (-G) or quantum field energy. This action field complements the sensible energy or vis-viva heat as molecular kinetic motion and its recognition should have significance for designing more efficient heat engines or better understanding of the heat engine powering the Earth’s climates.

Two-dimensional heat diffusion problem with heat source which is quasilinear parabolic problem is examined analytically and numerically. Periodic boundary conditions are used as a boundary conditions. Since the problem is not linear, Picard’s successive approximation theorem is used. Under certain conditions of natural regularity and consistency imposed on the input data, establish the existence, uniqueness and constant dependence of the solution on the data using the generalized Fourier method. As a numerical solution, implicit finite difference scheme is used. The results ob-tained from analytical and the numerical solutions are so close to each other.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

We study epidemic spreading in complex networks by a multiple random walker approach. Each walker performs an independent simple Markovian random walk on a complex undirected (ergodic) random graph where we focus on Barabási-Albert (BA), Erdös-Rényi (ER) and Watts-Strogatz (WS) types. Both, walkers and nodes can be either susceptible (S) or infected and infectious (I) representing their states of health. Susceptible nodes may be infected by visits of infected walkers, and susceptible walkers may be infected by visiting infected nodes. No direct transmission of the disease among walkers (or among nodes) is possible. This model mimics a large class of diseases such as Dengue and Malaria with transmission of the disease via vectors (mosquitos). Infected walkers may die during the time span of their infection introducing an additional compartment D of dead walkers. Infected nodes never die and always recover from their infection after a random finite time. This assumption is based on the observation that infectious vectors (mosquitos) are not ill and do not die from the infection. The infectious time spans of nodes and walkers, and the survival times of infected walkers, are represented by independent random variables. We derive stochastic evolution equations for the mean-field compartmental populations with mortality of walkers and delayed transitions among the compartments. From linear stability analysis, we derive the basic reproduction numbers R M , R 0 with and without mortality, respectively, and prove that R M < R 0 . For R M , R 0 > 1 the healthy state is unstable whereas for zero mortality a stable endemic equilibrium exists (independent of the initial conditions) which we obtained explicitly. We observe that the solutions of the random walk simulations in the considered networks agree well with the mean-field solutions for strongly connected graph topologies, whereas less well for weakly connected structures and for diseases with high mortality. Our model has applications beyond epidemic dynamics, for instance in the kinetics of chemical reactions, the propagation of contaminants, wood fires, among many others.

This study examined the impact of differences in fruit load of olive trees on the rate of stem refilling. The experiment was conducted in a commercial olive orchard over the consecutive years of 2021 and 2022, during which the biennial bearing cycle of olive trees resulted in minimal fruit production in 2021 and maximal production in 2022. The rate of stem refilling was determined by quantifying the differences in water volume traversing the apex and base of the principal branches of experimental trees using sap flow sensors. Concurrent measurements of tree water status were also conducted using psychrometers, while soil moisture content dynamics were continuously recorded. Results indicate that alternate bearing significantly influences the stem refilling process, while soil moisture availability also plays a pivotal role. Water reserves were more intensively utilized during the year of full production (“ON” year) primarily to fulfill the water demands of developing fruits. This replenishment occurred in various periods during the day, including early morning, afternoon, and night, when stomatal conductance measurements indicated stomatal closure. The study suggests a more intense replenishment of reserves during the night in "ON" year trees, irrespective of soil moisture, water vapor pressure deficit, or phenological fruit development stage.

This work studies how the Elo rating system can be applied to score-based sports, where it’s gaining popularity, and in particular for predicting the result at any point of a game, extending its statistical basis to stochastic processes. We derive some new theoretical results for this model and use them to implement Elo ratings for basketball and soccer leagues, where the assumptions of our model are tested and found to be mostly accurate. We showcase several metrics for comparing the performance of different ratings systems and determine whether adding a feature has a statistically significant impact. Finally, we propose an Elo model based in a discrete process for the score that allows us to obtain draw probabilities for soccer matches, and has a performance competitive with alternatives like SPI ratings.

An overview of the link between nonequilibrium thermodynamics and complexity theory is offered. It is shown how the rate of entropy production can be quantified through the spectrum of the Lyapunov exponents. It was shown how the entropy production per unit of time meets the necessary and sufficient conditions to be a Lyapunov function and constitutes per se an extremal principle. The entropy production fractal dimension conjecture was established. It is shown how the rate of entropy production as a non-extremal criterion represents an alternative way of sensitivity analysis of differential equations. Finally, an extension to biophysical-chemical systems, on the one hand, the use of the dissipation function is shown, as a thermodynamic potential out of equilibrium, in the characterization of biological phase transitions. On the other hand, it was evidenced how the rate of entropy production represents a physical quantity to evaluate the complexity and robustness of cancer.

Lindernia dubia (L.) Pennell is a species with invasive behavior outside of its native range of distribution (North America), linked mainly to aquatic habitats. This annual species has been acknowledged as a weed in rice paddies in Europe and Asia. Due to the impacts of this invasive plant, some authors have even listed this species as a global invader. The present work focused on spontaneous plant species occurring in cattail seedlings grown in central Spain for the establishment of constructed wetlands. Weed inventory revealed the presence of L. dubia as a dominant spontaneous species in this crop environment. A suite of mesocosm experiments were designed to study the distribution of L.dubia versus the distribution of the other dominant plant species, and to determine traits associated with its weedy potential. Results showed that L.dubia presents competitive attributes such as morphological variability, early flowering, long seeding time, short growth cycle, small and light seeds and high seed production and germination rate (25 ⁰C), meaning a high reproductive capacity in a cycle of about three months, in non-limiting conditions for plant growth. Data from this work provide a basis for understanding the weedy potential of L.dubia, and for management decisions of a potentially invasive species, little investigated in Europe

New analytical solutions of the heat conduction equation are presented in cylindrical and spherical coordinates. Then these solutions are reproduced with high accuracy by recent explicit and unconditionally stable finite difference methods. After this, real experimental data from the literature regarding a heated cylinder are reproduced by the explicit numerical methods as well as by Finite Element Methods (FEM) ANSYS workbench. Convection and nonlinear radiation are also considered on the boundary of the cylinder, and it is shown that the explicit methods are much more accurate than the commercial software.

This paper shares some new information on the ambient temperature profile and the heat stress occurrences directly underneath ground-mounted Solar Photovoltaic (PV) Arrays (monocrystalline-based) focusing on different temperature levels. A common ground for this work lies on the fact that 10C increase of PV cell temperature results in reduction of 0.5% energy conversion efficiency thus any means of natural cooling mechanism would gain much benefit especially to the Solar Farm operators. Transpiration process plays an important role in the cooling of green plants where in average it could dissipate around 32.9% of the total solar energy absorbed by the leaf making it a good natural cooling mechanism. This condition is relatively applied for herbs specifically for this project, Orthosiphon Stamineus or generally known as Java Tea are used as the high value crops. The thermal process via convective heat and mass exchange of leaves with the environment is relevant for a better understanding of plant physiological processes in response to environmental conversion factors for a wide range of applications. An important fact for plant heat stress with respect to the Ambient temperature is that the range lies between 10 C to 15 C above the surrounding value. This heat stress condition is relatively important and should be modelled in crops-energy integration. Agrivoltaic concept is a system that combines commercial agriculture and photovoltaic electricity generation in the same space. The concept is in line with the Kyoto Protocol and the United Nation Sustainable Development Goals (UN-SDG) which highlights the clean energy and sustainable urban living. The integration of agrivoltaic systems would optimize the yield, improving clean system efficiency and solving the issue of land resource sustainability. The PV bottom surface temperature are the main source of dissipated heat as shown in the thermal images recorded at 5 minutes interval at 3 sampling time. Statistical analysis shows that the Thermal correlations for transpiration process and heat stress occurrences between PV bottom surface and plant height will be an important finding for large scale plant cultivation in agrivoltaic farms.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Determination of antibody titre of dogs vaccinated against canine distemper in Jos North and South local Government Areas of Plateau State was carried out by collection of sera of vaccinated dogs and administration of well-structured questionnaires to dog owners. The samples collected were analyzed using the immune-blot ELISA Kit to determining the antibody titre (immunoglobulin G). It indicated that dogs vaccinated against the disease mounted adequate protective immunity. The result revealed that 54 (90.0%) of the sampled dogs have protective immunity, with those given more than one dose having higher level of protective antibody. Statistically, the result showed that the antibody titre did not differ significantly in relation to immunity and sex, breed, age and location but significant difference was seen in relation to number of primary vaccination. The result also revealed that those dogs that received booster doses (secondary vaccination) had more protective antibody. The study was aimed at evaluating the antibody titre of dogs vaccinated against canine distemper in Jos, Plateau State.

In this chapter we study the unstudy effect on MHD preamble porous medium through with thermal absorption and heat generation in the oscillatory flow of visco-elastic fluid between two plates in the presence of Chemical reaction. The expressions for the velocity, temperature and concentration distributions are arthemitiaclly solved by perturbation method.

Ultraviolet light incident on organic material can initiate its spontaneous dissipative structuring into chromophores which can catalyze their own replication. This may have been the case for one of the most ancient of all chromophores dissipating the Archean UVC photon flux, the nucleic acids. Oligos of nucleic acids with affinity to particular amino acids which foment UVC photon dissipation would have been selected through non-equilibrium thermodynamic imperatives which favor entropy production. Indeed, we show here that those amino acids with characteristics most relevant to fomenting UVC photon dissipation are precisely those with greatest chemical affinity to their codons or anticodons. Entropy production could thus provide an explanation for the accumulation of information in nucleic acids relevant to the dissipation of the externally imposed thermodynamic potentials. The accumulation of information in this manner provides a link between evolution and entropy production.

As a new kind of highly compact and efficient micro-channel heat exchanger, printed circuit heat exchanger (PCHE) is a promising candidate satisfying the heat exchange requirements of liquefied natural gas (LNG) vaporization at low and high pressure. The effects of airfoil fin arrangement on heat transfer an flow resistance were numerically investigated using supercritical liquefied natural gas (LNG) as a working fluid. The thermal properties of supercritical LNG were tested by utilizing a REFPROF software database. Numerical simulation was performed using FLUENT. The inlet temperature of supercritical LNG was 121 K,and its pressure was 10.5MPa. The reference mass flow rate of LNG was set 1.22 g/s for the vertical pitch L_v = 1.67 mm and the staggered pitch L_s = 0 mm, with the Reynolds number of about 3750. The SST k-ω model with enhanced wall treatment was selected by comparing with the experimental data. The airfoil fin PCHE had better thermal-hydraulic performance than that of the straight channel PCHE. Moreover, the airfoil fins with staggered arrangement displayed better thermal performance than that of the fins with parallel arrangement. The thermal-hydraulic performance of airfoil fin PCHE was improved with increasing L_s and L_v. Moreover, L_v affected on the Nusselt number and pressure drop of airfoil fin PCHE more obviously. In conclusion, a sparser staggered arrangement of fins showed a better thermal-hydraulic performance in airfoil fin PCHE.

A non-Newtonian fluid model is used to investigate the two-dimensional pulsatile blood flow through a tapered artery with a stenosis. The mixed convection effects of heat and mass transfer are also taken into account. By applying non-dimensionalization and radial coordinate transformation, we simplify the system in a tube. Under the finite difference scheme, numerical solutions are calculated for velocity, temperature concentration, resistance, impedance, wall shear stress and shearing stress at the stenosis throat. Finally, Quantitative analysis is carried out.

Although evolutionary theory has yet to furnish a comprehensive rationale for the underlying mechanism of natural selection, it is pertinent to note that the phenomenon transcends the confines of biological systems, exhibiting analogous patterns in physical systems as well. Specifically, isolated and closed systems tend to evolve towards states of progressively increasing entropy. In scenarios where multiple paths for entropy increase are accessible, such systems tend to favor combinations of paths that exhibit the most rapid entropy increase rates. Among the various processes in nature, life activities constitute a salient means of achieving entropy increase. Genetic variation within organisms generates individuals that vary in their rates of entropy increase. As these organisms interact, compete and combine, they form diverse combinations of entropy-increasing pathways. Nature, in turn, selects among these combinations, favoring those that culminate in the fastest entropy increase, thereby propelling the evolution of life. Essentially, the evolution of life is an ongoing exploration of diverse combinations of pathways that maximize entropy increase across various energy pools. Amidst continuous genetic variation and the selective pressure imposed by nature for maximum entropy production rates, information accumulates, leading to a corresponding acceleration in the rate of entropy increase. This natural selection, which favors maximizing the entropy at the fastest possible rate, serves as the ultimate driving force for the origin and evolution of life.

The maximization of entropy S within a closed system is accepted as an inevitability (as the second law of thermodynamics) by statistical inference alone. The Maximum Entropy Production Principle (MEPP) states that not only S maximizes, but $\dot{S}$ as well: a system will dissipate as fast as possible. There is still no consensus on the general validity of this MEPP, even though it shows remarkable explanatory power (both qualitatively and quantitatively), and has been empirically demonstrated for many domains. In this theoretical paper I provide a generalization of entropy gradients, to show that the MEPP actually follows from the same statistical inference, as that of the 2nd law of thermodynamics. For this generalization I only use the concepts of super-statespaces and microstate-density. These concepts also allow for the abstraction of 'Self Organizing Criticality' to a bifurcating local difference in this density, and allow for a generalization of the fundamentally unresolved concepts of 'chaos' and 'order'.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

Higher order femtoscopy measured to examine the heat exchanger characterization of the fluid debris produced in the collisions and investigated a remarkable suppression in the bosons interferences measurement. The analogous suppression can be analyzed to explore the coherence of boson thermal particle production sources at unprecedented energies. We illustrate the particles emissions from radiated sources with statistical coherence which induce the thermal particles interferences to probe the peculiarity of the heated sources as well as the distinctions about the heat exchangers in the collisions at higher temperature. We perspicacious that the bosons seem to the pertinent aspirant of heat exchanger, and the normalized three particles correlators evaluate the existence of such hybrid phases significantly. The key point of this research is that we analyze the three particles correlations with their normalized correlations by difference equations to determine the characteristics of heat exchanger and its applications. With such distinctive and efficient approach, we observe a significant difference in the correlation functions at higher temperature and momenta regimes.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.