The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

Introduction: The Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) infection may cause acute respiratory failure but also remains responsible for many other pathologies, including electrolyte disorders. SARS-CoV-2 infection can cause dysfunction of the renin-angiotensin-aldosterone system and disrupt water hemostasis with thirst and appetite abnormalities. Dysnatremia affects prognosis and may be associated with mortality in patients admitted to SARS-CoV2 intensive care. Patients and Methods: The study included 209 patients admitted to the Intensive Care Unit between April 12, 2021, and March 1, 2022 who were over 18 years old and diagnosed with SARS-CoV-2 infection by clinical and thoracic tomography findings or with a positive reverse transcription polymerase chain reaction (RT-PCR) test result. The laboratory markers, treatment modalities, nutritional, and respiratory support also for outcome evaluation, length of stay in the ICU, total hospitalization duration, and mortality in ICU were recorded.The laboratory marker comparison was made admission with the final assessment performed before the time of mortality in ICU or discharge. Results: Inotropic requirements among patients were high which was reflected in the first-month mortality. Hypernatremia presence was associated with an increase in enteral support and inotropic support requirement and mortality. Hypernatremia was correlated with diabetes mellitus, chronic renal failure, and a longer duration under mechanical ventilation. Discussion: Hypernatremia was an important risk factor in ICU patients hospitalized for SARS-CoV-2 infection, which was also affected by the treatment regimens given itself. This complex relationship underlies the importance of proper electrolyte management, especially in patients who were under severe stress and organ failure.

Background/Objectives: Nail technicians frequently have musculoskeletal pain, which impairs their job performance. A high-risk profession linked to back discomfort that causes morbidity is nail technician. QEC is a tool used for observing and assessing risks in a work environment. The goal of this research is to assess the ergonomic risks, pain, and their relationship with posture among manicurists. Methods: The 35 nail technicians filled the assessment form which consists of occupational information, pain, European Community Respiratory Health Survey, Nordic Musculoskeletal Questionnaire and QEC worker part. Physicians assessed nail technicians’ workspace and QEC outcomes. Results: It was stated that they worked an average of 61.92±11.09 hours per week, served an average of 11±5 customers per day, and their condition lasted 53.96±36.51 months. There is a strong significant correlation between discomforts, time spent in occupation (p=0,000) and working hours. Manicure, pedicure, unwanted hair removal, correction of eyebrow were considered for ergonomic risk evaluation. Each occupation accompanied repeated bad postures. Most of them were scored in very high risk categorization for back static positions (more than 29 point). Conclusions: This study may be useful for nail technicians seeking ergonomic improvements in the areas of engineering, administration, behavior, or personal.

Background: The Advanced Lung Cancer Inflammation Index (ALI) is a novel, comprehensive index that integrates inflammation and nutritional status, incorporating parameters such as albumin, body mass index (BMI), and the neutrophil-to-lymphocyte ratio (NLR). Unlike traditional inflammation biomarkers, this study aims to evaluate the prognosis of IPF patients by considering both inflammation and nutritional status. Method: A total of 102 patients with IPF were included in the study. Clinical data were obtained from the patients’ medical records. NLR and ALI score were calculated based on data collected at the initiation of antifibrotic treatment using the following formula: Neut/Lym and albumin × BMI / NLR. Results: IPF subject subgroups in terms of ALI based on gender–age–physiology (GAP) stages (1,2,3), FVC (median split, <70% vs ≥70%), DLCO (<51% vs ≥51%), 6-Minute Walk Test (6MWT) (<350 vs ≥350) and CCI (≤1 vs >1). ALI showed significant difference depending on the categories of GAP stage, FVC, DLCO, and 6MWT but these differences were not observed based on the charlson comorbidity index (CCI) categories (sırasıyla p=0.000, p=0.000, p=0.000, p=0.001, p=0.233). Receiver Operating Characteristic (ROC) curve analysis was performed to evaluate the sensitivity and specificity of ALI, albumin, NLR, and BMI in determining the mortality risk in IPF patients. ALI demonstrated a sensitivity of 63.6% and a specificity of 98.9% at a threshold of 11.2 (AUC = 0.945, 95% CI 0.892–0.998, p < 0.000). Conclusion: We determined that ALI levels are significantly associated with disease severity and mortality in patients with IPF.

The objective of this study was to investigate the impact of athletes' respiratory muscle strength, as assessed through maximal inspiratory (MIP) and expiratory pressure (MEP), on aerobic endurance, as indicated by maximal oxygen consump-tion (Max VO2) kinetics. Respiratory muscle strength was assessed using a digital spirometer (Pony FX Cosmed, Italy), while maximal oxygen utilization capacity was measured using a breath-by-breath automatic portable gas analysis system (Cosmed K5, Italy). Statistical analysis was conducted utilizing SPSS 22.0. Based on the standardized regression coefficients (β), it was found that MEP (mean ± SD: 130.95 ± 42.82) and inspiratory diaphragmatic circumference values significantly influenced ventilatory equivalent (VE), oxygen consumption (VO2), and carbon dioxide pro-duction (VCO2). Conversely, the remaining predictor variables did not exhibit a sig-nificant effect on VE (mean ± SD: 134.80 ± 36.69), VO2 (mean ± SD: 3877.52 ± 868.47 ml), and VCO2 (mean ± SD: 4301.27 ± 1001.07 ml). In contrast, measurements of chest circumference (mean ± SD: 91.40 ± 10.72 cm), MEP, and diaphragmatic cir-cumference during inspiration (mean ± SD: 95.20 ± 10.21 cm) were found to signifi-cantly impact Max VO2 (mean ± SD: 58.52 ± 10.74 ml/kg/min), while the other pre-dictor variables did not demonstrate a significant effect on Max VO2. Conclusively, the study revealed that measured values of diaphragmatic circumference during inspiration and MEP exerted a notable influence on Max VO2, VE, VO2, and VCO2. Our findings underscore the importance of considering respiratory muscle strength in assessing and enhancing athletes' aerobic performance. These insights contribute to a deeper understanding of the interplay between respiratory function and exercise capacity, offering potential avenues for optimizing training regimens and perfor-mance outcomes in athletic contexts.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Background This study aimed to examine the acute effects of different pre-ST strategies on muscular performance and blood pressure (BP) responses in recreationally strength-trained women. Methods: Twelve overweight women with normal-to-elevated BP were recruited and performed six exper-imental protocols in a randomized order: 1) control protocol (CC) – BP assessed without exercises performed, 2) strength training (ST), 3) foam rolling warm-up followed by strength training (FR+ST), 4) specific warm-up followed by strength training (SW+ST), 5) aerobic exercise followed by strength training (AE+ST), and 6) stretching exercises followed by strength training (SE+ST). Strength training consisted of three sets at 80% of 10RM with a self-suggested rest interval between sets for bench press, back squat, bench press 45º, front squat, lat pull-down, leg press, shoulder press, and leg extension. Results: All experimental protocol had a lower total training volume, fa-tigue index, and repetitions performance in relation to ST (p

The aim of this work was to describe the physiological limitations induced under drought conditions in young sweet orange trees, including the crop capability to recuperate its physiological status once re-watering, and after a water withholding. The trial was conducted during two consecutive months (July and August) in two-years old sweet orange trees. Three irrigation treatments were arranged: A full irrigation treatment; (FI); a low-frequency deficit-irrigation treatment (LFDI); and a sustained-deficit irrigation (SDI) treatment. The obtained results showed that for Stem values below -1.5 MPa, significant decreases in gas exchange rates, evidencing diffusive limitations to drought stress. Additionally, there was evidence of increased osmolyte synthesis, compatible as a defensive response to prevent oxidative damage. Likewise, the isohydric behaviour observed also resulted in significant decreases in gs even for moderate stress situations. In addition, it was observed that in the LFDI treatment, the stress levels reached caused a significant increase in the levels of Pro and MDA, which were not equal to those detected in FI during the recovery periods, which leads us to assume that potential values below -1.8 MPa would be causing significant oxidative damage with no capacity for subsequent recovery, and probably affecting the final yield.

Aim: To investigate inflammation indices and erythropoietin (EPO) levels for their potential role in distinguishing polycythemia vera (PV) from secondary polycythemia (SP), and to compare different parameter combinations in terms of diagnostic accuracy. Methods: This retrospective cohort was created from patients assessed for polycythemia from January 2020 to December 2023. PV diagnosis was made according to the 2016 WHO criteria (n=145). Those who did not fulfill the criteria were defined as having SP (n=84). Results: NLR, PLR and SII were significantly higher in the PV group (p

If we assume that: a. The four fundamental forces of nature are independent waves without rest masses, and their speeds are constant in a vacuum, just like light. b. Light or electromagnetic waves and gravity are comparable in structures. Weak and strong interactions are similar in structures. c. Light and weak interaction have the same speed c_L with spin number +1 or –1. d. Gravity and strong interaction have the same speed c_G without spin. e. The primary particles, namely electrons, electron neutrinos, and dark neutrinos in this paper, are made by the above four waves. We can find and describe some fundamental characteristics of the primary particles (e.g., their sizes, energies, and interactions) and introduce new attractive results from them (e.g., the source of the Pauli exclusion principle, the solution to the Einstein-Podolsky-Rosen paradox, and c_G slightly faster than c_L).

Preventive Maintenance (PM) is a periodic maintenance strategy, which has great results for devices in extending their life, increasing productivity, and most importantly, help avoid unexpected breakdowns and their costly consequence. A preventive maintenance scheduling (PMS) is determining the time for carrying out PM, and it represents a sensitive issue in terms of impact on production if the time for the PM process is not optimally distributed. In this study, hybrid heuristic methods were used to solve the PMS problem, as genetic algorithm and Tabu research were adopted. The optimal solution was reached in a short time compared to previous studies in which optimal methods were used, integer programming and nonlinear integer programming. Also, sensitivity analysis was applied to measure the robustness and strength of the method used, where an optimal solution was obtained for all experiments and in record time. This method can be used for power plants in privet or public sectors, to generate an optimal PMS, to save money, and to avoid water or electricity cuts.

Composites, and especially carbon fiber reinforced plastics (CFRPs), are increasingly used in the automotive, aerospace, and aviation industries, and as a result, CFRP production has increased dramatically, leading to a corresponding increase of waste. Landfill and incineration of waste are likely to be restricted as a result of the legislation, thus highlighting the need for efficient recycling methods for CFRPs. However, the recycling of CFRP is very challenging, mainly due to the difficulty of removing the thermosetting matrix. This study reports a pre-screening of the solvolysis recycling process for CFRPs based on the mechanical properties of the recovered fibers. To this end, solvolysis tests were conducted on unidirectional CFRP samples under supercritical and subcritical conditions using acetone and water. The solvolysis tests were conducted for various conditions of temperature, pressure, and reaction time. The efficiency of the recycling processes has been evaluated through a morphological and a mechanical characterization of the recovered fibers. In most cases, the decomposition efficiency of the epoxy resin, measured in terms of mass, ranged between 90 and 100%. Moreover, the scanning electron microscopy images of the recovered fibers showed negligible traces of resin residues and no detectable signs of physical damage or any changes in morphology with regard to diameter. Finally, the single-fiber tension tests revealed that that the recovered fibers retained more than 61% of their initial Young's modulus and 70% of their tensile strength.

The purpose of this study is to examine the match-related performance (scores and penalties) of the athletes in the Junior EJC (European Judo Championship) and U23 EJC categories before and immediately after the Covid-19 quarantine, according to gender and weight category groups. Our sample was based on the junior and U23, male and females, 2019-2020 Junior European Judo Championships and 2019-2020 U23 European Judo Championships. A total of 1431 matches in these tournaments were analyzed: male (n=812) and female (n=619). The main findings of this study showed that most matches in both the male and female categories resulted in ippon (2019-2020 average: 64,35% for Junior male, 70,55% for U23 male and 69,3% for Junior female, 64,4% for U23 female). No significant differences (p &gt; 0.05) were observed between gender and age groups concerning the match scores. In the formation phase of the technique, considerations of high- and low-intensity actions, and analysis of the speed of athletes during matches in official competitions can help to better understand the dynamics of the variability of movements in judo matches. In addition, suggestions are presented to be applied to athletes in different age categories who are on the way to become Olympic athletes.

Resistance training is beneficial to adults for improving muscle strength and reducing the body composition. Nevertheless, little is known regarding online resistance training on anthropometric parameters and muscular strength (MS) in overweight female adolescents. This study aimed to examine the effects of online resistance training on anthropometric parameters and muscular strength (MS) in overweight female adolescents. This prospective, single-center, single-blinded, randomized controlled study included 60 overweight female adolescents who were divided into a control group (n=30) and an intervention group (n=30). The intervention group performed online resistance training, which focused on body weight training of 12 components (4 sets, 12 repetitions) for 45 min, three times per week, for 12 weeks. The intensity of training was 65–75%. Anthropometric parameters, including body weight (BW), body mass index (BMI), body circumference measurements (BCM), and muscle strength (MS), were assessed. All parameters were measured at weeks 0, 8, and 12. Within-group and between-group comparisons were performed. The results revealed improvements in MS, BW, BMI, and BCM in the intervention group. However, chest circumference was not significant. These findings suggest that online resistance training was effective in improving MS and reducing the body composition and circumference.

The effectiveness of combining strength-specific training with endurance training to enhance the performance of endurance runners remains uncertain. This study aimed to analyze effect of practising maximum-strength (MAX), explosive strength (EXP) or both combined (COMB) on seven runners’ performance-indicators: vertical jump (VJ), one-repetition-maximum-squat (1RM), peak-velocity/peak-running-speed (PV), lactate-threshold (over incremental-test-protocols, LT), middle-distance-time-trial (TT), maximum-oxygen-consumption (VO2max), running-economy (RE). Systematic-review (Scopus, Wed of Science, Sports Discuss, PubMed) with meta-analysis was conducted following PRISMA standards. Inclusion-criteria (PICOS) were: recreational or well-trained athletes aged 18-45 performing concurrent-training ≥five-week. Used search-terms were related to different types of strength/endurance, participants’ age, sport-modality. 20 manuscripts were selected, quality-assessed with PEDro. MAX training is more effective than EXP, COMB in improving VJ, 1RM, PV, while COMB is more effective than MAX, EXP to enhance TT. MAX is more effective than EXP in improving LT. Concurrent-workouts do not provide additional benefits to VO2max. It is unknown which strength-modality (MAX, EXP or COMB) is more effective in improving RE. Concurrent-training is more effective than single-mode-endurance-training for enhancing specific performance-variables in adult-endurance-runners. Middle-, long-distance-runners may consider incorporating MAX-training to target specific goals, e.g., improving VJ, 1RM, LT, PV while utilizing COMB-training to enhance TT. Certain variables may benefit from EXP. New randomized-controlled-trials are required to confirm these findings.

This research paper aims to evaluate and model the performance of rice husk gasifier cook stoves for household energy use, a byproduct of rice milling. The study aims to address environmental issues and promote the use of rice husk as a renewable energy source and pest repellent in stoves. The study compared insulated and non-insulated gasifier stoves using rice husk gasification. The study compared the start-up time of insulated and non-insulated gasifier stoves, where the insulated stove showed a lower start-up time, but there was no significant difference at a 5% probability level. The temperature change also was not significant, as heat transfer and temperature change started when the husk was ignited. The burner stoves had different size and volume. The maximum operated or flame temperature was 1,190.30oC at room or minimum temperature of 27.33 oC, whereas the average temperature was 758.916oC for the non-insulated type of gasifier stove. The insulated gasifier stove also observed maximum and average temperatures of 518.30 oC and 289.014oC respectively at the same room temperature. The operating time of stoves directly influences the fuel consumption rate, specific gasification rate, and combustion zone rate of stoves. The fuel consumption rate has a significant effect on the type of gasifier stove, with the maximum rates being 3.820 and 2.099 kg/hr. The time to consume rice husks to gasify them depends on the density of the rice husk, reactor volume, and fuel consumption rate. The average specific gasification rate for insulated and non-insulated stoves is 106.45 and 120.63 kg/m2h, respectively. The fuel or rice husk holding capacity of each type of stove is significant at a 5% level, with the amount of rice husk and biochar produced being 1.18kg and 0.27kg for insulated stoves, and 2.511kg and 0.688kg for non-insulated stoves, respectively. The performance of gasifier stoves varies based on the bio char conversion rate, with non-insulated stoves producing a higher bio char mass per rice husk. Multiple regression analysis was used to model the relationship between time elapse with temperature and heat energy. The Squirrel-2020 data logger was used to measure the temperature produced by burning rice husks in the reactor of the stove as well as related generated and losses of heat. A relationship between the heat energy produced and the operating time of gasifier stoves was conducted to estimate the model. The cubic polynomial model was found to be the best predictive model fit for all variables of this study.

(1) Background: Conventional strength training and core exercises are commonly prescribed to improve cycling performance. Although previous studies have explored the utility of strength training in various cycling populations, this intervention has never been compared to core exercises; (2) Methods: 36 trained road cyclists were divided in 3 groups of 12 participants that performed either no strength training, conventional strength training or core exercises, in all cases together with their regular cycling training during a 12-week period. Peak power outputs across different durations (5 seconds, 60 seconds, 5 minutes, and 20 minutes) were recorded before and after the intervention; (3) Results: Conventional strength training is superior to core training and no strength training for all measured durations. At the same time, core training results in improved 5 second power output when compared to no strength training, while all the other measures are comparable among groups; (4) Conclusions: Conventional strength training is superior to core exercises and no strength training in trained road cyclists, and accordingly, it is recommended that this population incorporates strength training during their regular weekly workouts.

In this article, the sol-gel method was used as a synthesis method, which shows the physico –chemical nature of the synthesis of a new complex material ferrit Li0.5MnFe1.5O4. The synthesized structure and structure were determined by the method of X-ray phase analysis. According to the analysis indicators, it was found that our compound is single-phase, spinel-structured, and syngony - cubic type. The microstructure of the compound and the quantitative composition of the elements contained were analyzed under a scanning electron microscope (SEM). Through a scanning electron microscope, Microsystems were taken from different parts of l Li0.5MnFe1.5O4-type crystallite, the elemental composition of crystals was analyzed, and the general type of surface layer of complex ferrite was shown. As a result, the fact that the compound consists of a single phase, the clarity of its construction was determined by the topography and chemical composition of the compound. As a result, it was found that the newly synthesized complex ferrites correspond to the Formula Li0.5MnFe1.5O4. The particles of the formed compounds have a large size (between 50.0 μm, 20.0 μm and 10.0 μm). Electro physical measurements were carried out on the LCR - 800 unit at intervals of 293-483 K and at frequencies of 1.5 and 10 kHz. The increase in frequency to 10 kHz led to a decrease in the value ε in the range of the studied temperature (293-483 K).

While the role of safe riding behavior as a safety contributor for cyclists has been increasingly studied in recent years, there have been few studies analysing cycling behavior in relation to crash-related outcomes in Baltic countries. Indeed, to the best of our knowledge, this is the first time this issue has been addressed in the case of Latvia. Aim: The objective of this study was to assess the relationships among self-repotted cyclists’ behavior, traffic safety literacy, and their cycling crash involvement rates. Method: A total of 299 cyclists aged M=32.8 from across Latvia (42% females) participated in an online survey, which comprised questions regarding respondents’ demographics, frequency of riding, and the number of crashes in the past five years. The Cycling Behavior Questionnaire (CBQ) and the Cyclist Risk Perception and Regulation Scale (RPRS) were applied to assess cyclists' behavior patterns and traffic safety literacy. Results: According to the findings, it can be inferred that cyclists frequently engage in riding errors and traffic violations while cycling. Those who exhibit more antisocial behavior patterns are also more likely to be involved in road crashes. Conversely, cyclists with greater positive behavior rates more often also tend to possess better knowledge of traffic rules and exhibit a heightened risk perception, indicating a greater awareness of road traffic safety. Conclusion: All in sum, this study underscores key age differences, with older individuals significantly less involved in riding crashes, exhibiting fewer driving errors and a higher level of risk perception, which serves as a crucial factor in road safety. At the practical level, these results stress the need to address both traffic safety literacy and protective cycling factors of cyclists, in a manner to improve overall road safety and promote active transport modes in Latvia.

Introduction:Lumbar radiculopathy, frequently triggered by disc herniation, affects around one in 50 young adults (30-55 ages), leading to significant impacts on quality of life. When conservative treatments fail to alleviate symptoms, surgical intervention such as discectomy is often pursued. Technological advancements have led to various minimally invasive techniques, promising improved outcomes. Our aim was to compare clinical outcomes of different techniques.Methods:We conducted a systematic search in PubMed using "lumbar disc hernia" and the meta-analysis filter. Inclusion criteria comprised meta-analyses focusing on lumbar disc herniation treatments, published in English. A rigorous selection process adhering to PRISMA guidelines ensured high-quality evidence extraction.Results:From 28,171 initial records, 31 meta-analyses involving 87,852 patients were included. Heterogeneity across the literature presented challenges, notably in study populations, surgical techniques, and research designs. Among the techniques evaluated, full-endoscopic lumbar discectomy (FELD) emerged as superior in various perioperative parameters, including Visual Analog Scale (VAS) scores, Oswestry Disability Index (ODI), operation time, and complications. Conversely, automated percutaneous discectomy (AUTD) consistently exhibited poorer outcomes, suggesting limited effectiveness compared to other techniques. Conclusion:Despite advancements, the heterogeneity observed in the literature underscores the need for standardized approaches in minimally invasive spinal surgery research. FELD stands out as a preferred technique, offering favorable outcomes across multiple parameters. Conversely, techniques like AUTD raise concerns regarding efficacy. Future research should aim for uniformity in methodologies to facilitate accurate comparisons and guide clinical decision-making.

This study checked whether vitamin D (Vit-D) supplementation improves the efficacy of resistance training (RT) in terms of increasing muscle strength and lean body mass (LBM) and influencing cardiorespiratory fitness (VO2max) in Vit-D insufficient middle-aged healthy men. Participants (n = 28) were quasi‐randomly assigned to one of the two groups, which, in a double‐blind manner, supplemented their diet daily with either Vit‐D (8000 IU; VD) or placebo (PLC) during participation in a 12‐week supervised RT program. During the intervention, serum Vit‐D concentrations increased 2.6‐fold (p < 0.001) in the VD group, while no changes occurred in the PLC group. Muscle strength gains (p < 0.001) as measured in seven exercises performed on RT equipment and increases (p < 0.001) in LBM were similar in the two groups. Total fat mass, percent total fat, and percent android fat decreased (p < 0.05) to a similar extent in both groups, but there was no change in VO2max in either group. In conclusion, in healthy Vit‐D insufficient middle-aged men engaged in resistance training, Vit‐D supplementation increases serum 25(OH)D levels but does not enhance gains in muscle strength and LBM or decreases in fat mass and fat percentage and does not affect cardiorespiratory fitness.

Background: In recent years, whole blood parameters and derivatives have been used as prognostic criteria in the course of the disease in various diseases. The prognostic nutritional index (PNI), the systemic immune-inflammation index (SII), the neutrophil-lymphocyte ratio (NLR) have been adapted as an indicator of inflammation and have been widely studied to define the severity of inflammation in some diseases. The aim of this study was to evaluate the relationship between parameters such as NLR, SII, PNI, controlling nutritional status (CONUT) score, nutritional risk index (NRI) and with immunonutrition status and disease activity in patients with ischemic stroke of small vessel, large vessel and other etiologies. Methods: We retrospectively evaluated the records of 1454 consecutive ischemic stroke patients hospitalized in the emergency department of Gaziosmanpasa Education and Research Hospital from 2019 to 2023. Results: Of the 1350 SVO patients included in the study, 58.8% had small vessel, 29.3% had large vessel and 11.9% had other etiologies. There was a significant difference between the 3 etiology groups for PNI and CONUT. The median PNI was 47.03 (41.33-52.85) in the other etiology group, 35.29 (33.69-37.25) in the small vessel group, and 34.11 (30.23-36.87) in the large vessel group. The CONUT median was 5(5-6) in the small vessel group, 5(4-6) in the large vessel group and 4(4-4) in the other etiology group. In addition, CONUT and PNI were also found to be independent risk factors for death. A negative significant correlation was observed between PNI and NLR (r:-0.692), SII (r:-0.591), CONUT (r:-0.685). Significant correlations were observed between CONUT and NLR (r:0.402), SII (r:0.312). Conclusion: PNI and SII were significantly associated with disease activity. PNI, CONUT and NRI as a more accurate prognostic indicator of nutritional status in patients with ischemic stroke of small vessel, large vessel and other etiologies. NLR and SII may be important predictive markers in the course and prognosis of stroke.

The survival rates of women with stage 0 or 1 breast cancer stands at almost 100% and around 93% for stage 2. As the disease advances with decreasing survival, the rate detoriates to 72% for stage 3 and about 22% for stage 4 (ACS, 2018). Undoubtedly, earlier presentation is synonymous with better prognosis and survival. In fact data indicates that early stage breast cancer diagnoses has 90% survival rate as compared to 27% for the advanced states (ACS, 2018). In this regard, governmental and non-governmental agencies are working tirelessly towards the realization of improved breast cancer care and survival through early presentation and detection. For instance, the Sustainable Development Goal (SDG) Target 3.4 seeks to reduce by one third, premature mortality from cancers and other non-communicable diseases through prevention and treatment. Clearly, early presentation, diagnoses and treatment will assist in the realization of the SDG target 3.4 goal. To achieve this, research must be focused on early presentation among women with breast cancer.. However, current studies have focused mainly on advanced breast cancer regarding treatment, symptoms experience (emotional and psychological), coping and support systems, and the reasons for delayed diagnoses and treatment. Objective In this review, it is argued that, rather than focusing on advanced breast cancer which has been adequately explored, the attention has to be on what measures or approaches promote early presentations among Ghanaian women. Methods The review included all primary studies that provided answers to the phenomenon of interest. It included both quantitative and qualitative studies. Search scope encompassed studies within the last ten years; thus from 2010 to 2020 irrespective of the country of study.Studies were included if: The paper is of a primary study; the study population included women with early BC or BC symptoms; the study outcome is the association between early stage breast cancer and earlier presentation; the study has a comprehensive data analysis protocol; the results of the studies are unique.A thorough literature search was conducted using the following electronic database: Google scholar and Pubmed. Google scholar alert on new studies was subscribed. This gave update on newly published papers for appraisal and possible inclusion.Manual identified of other potentially eligible publications by searching the reference lists of retrieved studies was also done. After a thorough search, this review included studies from several countries around the Globe such as Ireland, London, Turkey, Iran, Ghana, Kenya, Ethiopia etc Data Collection The title and or abstract of all retrieved papers were independently scanned through to establish which studies should be further evaluated. The full texts of these potential articles were then assessed. Extraction The Cochrane extraction form for data extraction was resorted to. From each eligible article, the following study identifiers/information were extracted: author(s), first author, year, title, objective, article type, location, setting, study design and method, sample size, instruments used, and results. Results Prompt help seekers mainly self-discovered their BC, and this occurred through accidental touch, after menstruation, through breastfeeding, during grooming, and while taking their bath.Notably, women who were termed prompt help seekers had higher seriousness perception of their symptoms. This was likened to their level of understanding and awareness, as well as periodic examination and comparison. Similarly, women who knew they were at risk for breast on account of family history, and increased incidence of BC in their localities, labeled their initial symptoms as requiring prompt attention.Following interpretation and labeling of symptoms, the participants generally resorted to symptom monitoring until the onset of additional and or intense symptoms. Though most women thought of benign growths, a few feared it could be malignant. These emotional reactions led the women to purposively seek clarification by selectively consulting others. Further, participants opened up to social acquaintances such as family relationships, people with prior experience of breast disease, and in some few instances health professionals. Some women also resorted to media items to better their understanding. Remarkably, prompt help seekers sort for help within one month. Last but not least, some women first communed with their creator after discovery and labeling based on their spiritual affiliations.Also, researchers should consider conducting surveys to assess the BC risks for specific smaller groups. This would help tailor specific educational interventions to promote earlier presentation and treatment among the vulnerable.

Serum biochemical indicators serve as vital proxies that reflect the physiological state and functions of different organs. The genetic parameters and molecular mechanisms underlying serum biochemical indicators of sheep (Ovis aries) have not been well understood. Therefore, the aim of the present study was to identify genetic architecture and genomic loci underlying ten serum biochemical indicators in sheep, including alanine transaminase, aspartate transferase, lactate dehydrogenase, cholesterol, glucose, phosphorus, calcium, creatinine, urea concentrations and total protein levels. We implemented genetic parameter estimations and GWAS for each trait in 422 Akkaraman lambs. Overall, low to moderate heritability estimates were found, in the range 0.14–0.55. Additionally, low to high genetic correlations were observed among traits. In total, 23 SNP loci were associated with serum biochemical indicators leading to 19 genes . These are SPTA1, MGST2, CACUL1, IGFBP7, PARD3, PHB1, SLC15A5, TRIM35, RGS6, NUP93, CNTNAP2, SLC7A11, B3GALT5, DPP10, HST2ST1, NRP1, LRP1B, MAP3K9, ENSOARG00020040484.1 as well as LOC101103187, LOC101117162, LOC105611309 and LOC101118029. To our knowledge, these data provide the first association between SPTA1 and serum cholesterol and between ENSOARG00020040484.1 and serum glucose. The current findings provide a comprehensive inventory of the relationships between serum biochemical parameters, genetic variants, and disease-relevant characteristics. This information may facilitate the identification of therapeutic targets and fluid biomarkers and establish a strong framework for comprehending the pathobiology of complex diseases as well as providing targets for sheep genetic improvement programmes.

(1) Background: Plasmodium vivax causes the largest malaria burden in Brazil, and chloroquine resistance poses a challenge to eliminating malaria by 2035. Illegal mining in the Roraima Yanomami indigenous territory can lead to the introduction of resistant parasites. This study aimed to investigate mutations in the pvcrt-o and pvmdr-1 genes to determine their potential as predictors of P. vivax chloroquine-resistant phenotypes. (2) Methods: Samples were collected in two health centers of Boa Vista. A questionnaire was completed, and blood was drawn from each patient. Then, DNA extraction, PCR, amplicon purification, and DNA sequencing were performed. After alignment with the Sal-1, the amplified fragment was analyzed. Patients infected with the mutant parasites were queried in the Surveillance Information System. (3) Results: 98% (157/164) of participants were from illegal mining areas. The pvcrt-o was sequenced in 151 samples, and the K10 insertion was identified in 13% of them. The pvmdr1 was sequenced in 80 samples: the MYF haplotype (958M) was detected in 92% of them, the TYF in 8%, while MYL was absent. No cases of recrudescence, hospitalization, or death were found. (4) Conclusions: Mutations in the pvcrt-o and pvmdr-1 genes have no potential to predict chloroquine resistance in P. vivax.

Maximal athletic performance can be limited by various factors, including restricted respiratory function. These limitations can be mitigated through targeted respiratory muscle training, as supported by numerous studies. However, the full potential of respiratory training in competitive finswimming has not been fully investigated. This case study aims to evaluate performance variability during underwater phases in an elite Bi-Fins swimmer (current world record holder and multiple world championship medallist) over a 200m race simulation after an eight-week respiratory training using Airofit PRO™. Performance variability was assessed based on pre-test, inter-test, and post-test data. Each measurement included pulmonary function, body composition, and swim performance evaluations. The swimmer followed a 28-day training program with the AiroFit PRO™ respiratory trainer between tests. Significant improvements were observed in Wilcoxon paired-sample test between the pre-test and post-test in underwater distance (p=0.012; d=1.26), underwater time (p=0.012; d=1.26), and number of underwater kicks (p=0.043; d=1.01), resulting in a 14.23% longer underwater distance, 14.08% longer underwater time, and 14.94% increase in underwater kicks. Despite increased distance and time, underwater velocity remained stable, indicating improved underwater performance efficiency. The results suggest that the AiroFit PRO™ respiratory trainer has practical applications in finswimming training programs.

Backround: Thoracic trauma causes life-threatening organ injuries, ranging from simple abrasions to contusions of intrathoracic organs. In this study, we aimed to investigate the effects of bosentan on endothelin-1 (ET-1), hypoxia-inducible factor-1 (HIF-1), nuclear factor-kappa B (NF-κB), tumor necrosis factor (TNF)-α as inflammation markers, pro-oxidant antioxidant balance (PAB) and total antioxidant capacity (TAC) levels as oxidative stress parameters in lung tissues of rats in experimental model of pulmonary contusion (PC) induced by blunt thoracic trauma. Methods: Thirty-seven animals male Sprague-Dawley rats were divided into 5 groups. All 4 groups, except for the control group, were performed to PC. In the first group, C: control group (n=6) consisted of unprocessed and untreated. The second group, PC3 (n=8) underwent of 3 days PC performed. The third group, PC-B3 (n=8) received 100 mg/kg bosentan was given orally once a day for 3 days. The fourth group, PC7 group (n=7) underwent of 7 days PC performed, and the fifth group PC-B7 (n=8) received 100 mg/kg bosentan was given orally once a day for 7 days. While ET-1, NF-B, TNF-, and HIF-1 was measured by ELISA method, TAC and PAB by spectrophotometric in lung tissue samples. Results: ET-1, NF-B, TNF-, HIF-1, and PAB levels were higher, while TAC activities were lower in all groups compared with the control (p < 0.05). There was no significant difference in ET-1 and TNF-- levels between the PC-B3 and PC-B7 groups and the control group (p < 0.05) while NF-B, HIF-1, and PAB levels were still higher in both the PC-B3 and PC-B7 groups than in the control group. Bosentan treatment causes decreased ET-1, NF-B, TNF-, HIF-1, and PAB and increased TAC levels in comparison to the nontreated groups (p < 0.05). Conclusions: We found that the use of bosentan decreased the severity of oxidative stress in the lung and reduced the inflammatory reaction in rats with PC induced by blunt thoracic trauma. This suggests that bosentan may have protective effects on lung injury mechanisms by reducing hypoxia, inflammation and oxidative stress. If supported by similar studies, bosentan can be used in both pulmonary and emergency clinics to reduce ischemic complications, inflammation, oxidative stress in some diseases that may be accompanied by ischemia.

Training schedule is a factor that influences sports performance optimization. In a sport like soccer, there is often significant disparity in training schedules among different teams within the same club, without considering whether this may affect players' performance. The aim of this study was to describe differences in nutrient intake and body composition in elite youth soccer players from the Spanish league with different training schedules (morning and evening). A cross-sectional study was conducted to determine differences in anthropometric variables and dietary assessment in a sample of Spanish young soccer players. A total of 41 players participated in this study. After comparing the groups according to their training schedule, no differences were observed in body composition between both groups; the evening-night training group showed higher consumption of lipids and saturated fats. In summary, more experimental studies are needed to determine the effects on various health and performance parameters of different training schedules in young population.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

.Bacground: Sepsis remains a major health challenge worldwide, characterized by a dysre-gulated host response to infection, leading to high mortality and morbidity in intensive care units (ICUs). The Fibrosis 4 (FIB-4) index, originally developed to assess liver fibrosis in hepatitis C patients, has recently been explored for its potential prognostic value in sepsis patients. Method: This study retrospectively analyzed 309 sepsis patients admitted to the Internal Me-dicine and Anaesthesia ICUs between December 12, 2021, and December 15, 2023, to inves-tigate the relationship between FIB-4 levels, Acute Physiology and Chronic Health Evaluation (APACHE), and Sequential Organ Failure Assessment (SOFA) and clinical outcomes. Results: The study found that higher FIB-4 measurements were statistically significantly asso-ciated with increased 28-day mortality, with a cut-off value of 4.9 providing a sensitivity of 54.92% and specificity of 74.25%. Logistic regression analysis indicated that elevated Conclusion:FIB-4 levels were a significant predictor of early mortality, suggesting that the FIB-4 index could serve as a valuable prognostic tool in assessing the severity and prognosis of sepsis patients.

this paper focuses on a scientific study of the restoration, rehabilitation and reuse of the great throne hall, the most important hall in al-jawhara palace. it also aims to study the most important factors and forces of damage that affected the great throne hall, natural, biological, and human, and the resulting damage. field tests were performed, laboratory tests to determine fracture stress, liquidity and spandex limits tests, chemical analysis on soil samples and geoelectrical testing of the soil, and the results did not show caves or voids in the ground until a depth of 10.00 m, construc-tion materials were studied and tested using x-ray, (xrd), mechanical tests (tensile, shear, com-pression), and a study of the effect of seismic loads on the walls; the results showed horizontal and vertical cracks; based on the study and analysis of these cracks, it was possible to present modern techniques in restoration and reinforcement methods, and in conclusion, the researcher's recommendations.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Frailty syndrome, a significant contributor to morbidity and mortality in older adults, has traditionally been addressed through aerobic exercises. However, recent research has highlighted the importance of anaerobic and strength training activities in mitigating frailty. This article explores the shift from aerobic to anaerobic/strength training exercises, emphasizing the benefits of the latter in improving muscle strength, balance, and overall physical function. The discussion includes the physiological mechanisms underlying this shift, the evidence supporting strength training, and practical recommendations for implementation.

Background: Blood flow restriction training (BFRT) uses occlusion during low-intensity resistance training (&lt;50% of repetition maximum, 1RM) to reduce arterial blood flow and venous return, imposing greater metabolic stress but similar muscular hypertrophy and strength gains as high-intensity resistance training (HIRT). However, no study, to date, has incorporated BFRT in a collegiate strength and conditioning setting to assess ecological validity. We aimed to investigate the effects of adding 6-weeks of accessory BFRT or HIRT to NCAA Division III soccer players prescribed resistance training regimen on muscle strength and hypertrophy. Methods: Male and female (n=17) athletes were randomly assigned to complete biceps curls 2x/week under BFRT or control (HIRT), following the regularly scheduled strength training. Bicep strength (1RM) and circumference (BC) were assessed at weeks 0, 3, and 6. Results: In men, no significant interaction between time and condition was observed for BC (p=0.861), though condition (BFRT vs Control, p=0.025) and time (p=0.024) were significant. For 1RM, there was no significant interaction between time and condition (BFRT vs HIRT, p=0.067) or of condition (p=0.598), but there was a significant effect of time (p=0.004). In women, there was no significant interaction between time and condition (p=0.765) or of condition (p=0.971) on BC, but time was significant (p=0.045). For 1RM, there was no significant interaction between time and condition (p=0.227) or of condition (p=0.741), but time was (p=0.018). Conclusion: BFRT induced similar increases in muscle strength and hypertrophy as HIRT in soccer players, suggesting that BFRT could be incorporated into collegiate athlete training.

(1) Background: Youths with multiple risks and severe disadvantages experience poorer health and educational outcomes than less disadvantaged peers. To address problems with coping and self-regulation in this group, mental skills training (MST) approaches more commonly used in sport are an emerging intervention approach. (2) Methods and Results: This narrative review synthesizes literature to explain the need for MST, how it works, and evidence to support it works by focusing on two well evaluated programmes: LifeMatters and My Strengths Training for Life™. (3) Conclusions: To support positive youth development, MST is a strengths-based, flexible and adaptable approach to help fill the shortage of available evidence-based programs for those youths facing multiple disadvantages. The findings of this review may facilitate policy makers, commissioners, program planners, and researchers in the uptake of MST or similar psychoeducational approaches in future.

This study investigates the utilization of innovative green composites made from hemp shiv, a waste by-product of hemp cultivation, with the aim of promoting sustainability within the construction industry. The manufacturing method involve the application of pressure in a mold to create the samples. These materials were produced using an environmentally friendly binder consisting of colophony, arabic gum and corn starch, moreover white glue and bioepoxy are also used to compare with the green resins. Three different binder compositions for the specimens. The samples underwent mechanical testing through tensile and bending assessments, and their performance was compared to that of non-green binders to validate the effectiveness of the manufacturing processes. The study revealed that decreasing the moisture content during the curing process is crucial for improving the mechanical properties. The best results were achieved when using arabic gum as a binder, yielding a tensile strength of 2.16 MPa and a bending strength of 5.25 MPa, with a composition of 62.5% hemp shiv and a manufacturing process involving a pressure of 5 MPa.

Smart manufacturing encompasses a category of manufacturing that employs computer-integrated capabilities and technologies to enhance supply chain optimization, production efficiency, and recyclability. Yet limited studies have been conducted to optimize these prospects from the perspective of low resource countries where such innovative studies have not been adequately explored. This paper aims to examine the implications of smart manufacturing practices (Smart Procurement, Smart Supply Chain, Smart Production Planning and Control, Automation and Industrial Robot, and Supply Chain Configuration) on pro-environmental behaviour and develop a baseline moderated mediation model to explain the relationship between smart manufacturing and pro-environmental behaviour with a role of green dynamic capability, and environmental orientation. This study is anchored on quantitative research approach, deductive reasoning, and explanatory design. Cross – sectional survey data have been obtained from 382 manufacturing companies in Ghana. Our hypotheses have been tested using Structural Equation Modelling and SMART-PLS version 3.8.9. The study has revealed that smart manufacturing practices significantly and positively relate to pro-environmental behaviour. Moreover, green dynamic capability and environmental orientation moderate the relationship between smart manufacturing and pro-environmental behaviour. The implications of the study include the emergence of a baseline model to guide policymakers, practitioners, and academicians to explain the relationship between smart manufacturing and sustainable manufacturing in the context of developing countries. Again, the social implication of the study includes the realisation of decent job and economic growth, responsible consumption and production as well as actions taken to combat climate change.

Background: The maximal one-repetition test (1-RM) is widely used in scientific research; however, there are conflict results regarding its reproducibility in elderly population. The present study aimed to analyze the reproducibility the test both before and after a 12 week training period by using the bench press and leg press 45° 1-RM tests in the elderly taking into consideration the training experience and strength level of the women. Methods: Elderly women (n = 376; age, 68.5 ± 14.1 years; height, 162.7 ± 5.5 cm; body mass, 71.2 ± 16.0 kg) who underwent ≥3 months of resistance training performed an initial week of familiarization and a second week of testing and retest, with a 48–72 hour interval. Results: The results showed maximal and relative load strength of 39.3 kg and 0.59 kg/body mass for lower limbs and 20.9 kg and 0.31 kg/body mass for upper limbs. The Kappa indices were 0.93 and 0.95, and the intraclass correlation coefficients were 0.99 and 0.99 for the lower and upper limbs, respectively. Conclusion: Therefore, the present study confirms that the 1-RM test has high reliability and reproducibility in the elderly, for both upper and lower limbs.

The aim of the study was to assess the impact of two lengths of Nordic walking (NW) training interventions combined with time restricted eating (TRE) on improving body composition parameters, lipid profile, and levels of selected adipokines in women with disrupted body mass. Overweight and obese women (n=55, age: 21-85) were recruited. Four groups were selected: 6 weeks (SG6, n=13) and 12 weeks intervention (SG12, n=13); and two control groups: CON6 (n=13); and CON12 (n=13). The training sessions took place 3 times a week (60 minutes each) and were conducted outdoor under the supervision of professional coach. The training intensity was determined individually. The extended NW program combined with TRE induced a significant weight reduction in SG12 by 1.96 kg (p=0.010) and fat tissue by 1.64 kg (p=0.05). The proposed interventions did not affect LBM, TBW [kg], VFA and lipid profile. The LDL/HDL ratio changed with small size effect. Leptin concentration differed between groups (p=0.006), but not over time. For resistin, the differentiating factor was time (p=0.019, with lower results observed after the intervention). The change in leptin concentration was negatively correlated with its baseline concentration. Extended to 12 weeks, this intervention allows for an improvement in body composition. Neither 6 nor 12 weeks of training and fasting affected the lipoprotein profile.

This review summarizes studies dedicated to the assessment of microvascular function based on microcirculatory oscillations monitored by the FMSF technique. Two approaches are presented. The first approach uses oscillatory parameters measured under normoxia conditions, expressed as flowmotion (FM), vasomotion (VM), and the normoxia oscillatory index (NOI). These parameters have been used for identification of impaired microcirculatory oscillations associated with intense physical exercise, post-COVID syndrome, psychological stress, and erectile dysfunction. The second approach involves characterization of the microcirculatory response to hypoxia based on the measurement of hypoxia sensitivity (HS). The HS parameter is used to characterize microvascular complications in diabetes, such as diabetic kidney disease and diabetic foot ulcers. Based on research conducted by the authors of this review, the FMSF parameter ranges characterizing microvascular function are presented. The diagnostic approach to assessing microvascular function based on flowmotion monitored by the FMSF technique has a wide range of applications and potential to be integrated into widespread medical practice.

The astro-structures with the shape of comet and semi-circle, are found in the electronegative inductively coupled plasmas (ICPs), e.g., Ar/O2 and Ar/SF6. They are formed by means of the self-coagulation theory. This theory is built and based on two-dimensional fluid model simulation dynamic data of the above ICP sources. Concretely, quasi-Helmholtz equation is constructed through the free diffusion transport component and a novel negative chemical source term. The absolute value of recombination rate is higher than the attachment rate and so the net source of simulated anion is negative. This is quite a new chemical phenomenon in the electronegative and gaseous discharging plasmas when compared to the previously reported normal positive chemical source that will generate ambi-polar diffusion potential. In electronegative plasma, the self-coagulation is ambi-polar to sustain the electrical neutrality. Besides, when the anions are accelerated by ambi-polar potential before self-coagulated, the self-coagulation is again advective which leads to the formation of blue sheath. At the ambi-polar self-coagulation of high electronegativity, the electrons dynamics are relatively decoupled from ions and meanwhile they have their own relatively weak, spontaneous, and monopolar self-coagulation in the periphery of astro-structure. At the ambi-polar self-coagulation, both the anion and cation are individually treated as mass point models that carry charge (point charge models, more precisely). When the charge amounts of two individual astr-structures, e.g., semi-circle SF3+ and Ar+, are equal, the coagulated profile of heavy species SF3+ collapses by the expelling effect of Coulomb force that exists between the two point-charges. This is an anti-collective behavior of astro-structure, instead of the collective interaction of plasma, since the collapse of coagulated heavy species creates spatially dispersed charge density that cannot be shielded. The simulation shows that the lighter the species, the easier it self-coagulates, determined by the inertial effect of density quantity. The discharge picture of electronegative plasma is combined by a dynamic continuum transport (e.g., forming the ellipse background) and the mechanical balance contained in the static self-coagulation process (proven by dimensional analysis of continuity equation). The popular astro-structure of electronegative ICP source awaits urgently for the validation of experiment.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

It is aimed to examine the relationship between static and dynamic core training with strength, speed, jumping and taekwondo hitting performance in 12-14 years old taekwondo players. One of the most important features is the determination of the research design. The population of the study consists of male and female athletes between the ages of 12-14 who have been active in taekwondo for at least 2 years at Trabzon, Turkey. The sample of the study consists of app-proximately 30 athletes, approximately 15 female and 15 male athletes between the ages of 12-14, who voluntarily accepted to participate in the study. The data of the study were analyzed with SPSS 26.00 package program. Normality analysis was performed to determine whether the quantitative variables fit the normal distribution. Since the sample size of the study was 21 people (n=30), Shapiro-Wilk was analyzed According to the normal distribution criteria, nonparametric analyzes were performed because the variables were p<0.05. Frequency and descriptive statistics were used for descriptive statistics, and Wilcoxon Test was used for pretest-posttest comparison analysis. The results showed that core exercises had positive changes in muscle strength, anaerobic power and branch-specific striking techniques.

Polarimetry is used to determine the Stokes parameters of a laser beam. Once all four S0,1,2,3 parameters are determined, the state of polarisation is established. Upon reflection of a laser beam with the defined S polarisation state, the directly measured S parameters can be used to determine the optical properties of the surface, which modified the S-state upon reflection. Here, we demonstrate polarimetry for the determination of surface anisotropies related to birefringence and dichroism from different materials, which have a common feature of linear patterns of different alignments and scales. It is shown that polarimetry in the back-reflected light is complementary to ellipsometry and four-polarisation camera imaging.

Many clinical research datasets have a large percentage of missing values that directly impacts their usefulness in yielding high accuracy classifiers when used for training in supervised machine learning. While missing value imputation methods have been shown to work well with smaller percentages of missing values, their ability to impute sparse clinical research data can be problem specific. We previously attempted to learn quantitative guidelines for ordering cardiac magnetic resonance imaging during the evaluation for pediatric cardiomyopathy, but missing data significantly reduced our usable sample size. In this work, we sought to determine if increasing the usable sample size through imputation would allow us to learn better guidelines. We first review several machine learning methods for estimating missing data. Then, we apply four popular methods (mean imputation, decision tree, k-nearest neighbors, and self-organizing maps) to a clinical research dataset of pediatric patients undergoing evaluation for cardiomyopathy. Using Bayesian Rule Learning (BRL) to learn ruleset models, we compared the performance of imputation-augmented models versus unaugmented models. We found that all four imputation-augmented models performed similarly to unaugmented models. While imputation did not improve performance, it did provide evidence for the robustness of our learned models.

This paper presents a study on developing of a new exoskeleton for ankle joint rehabilitation with three degrees of freedom (3 DOFs). The primary attention is paid to the process of designing and modelling the device aimed at restoring the lost functions of joint mobility. The authors carried out a complex analysis of the functional requirements of the exoskeleton based on the research of potential user’s needs, which allowed them to develop a conceptual model of the proposed de-vice. In this study, a prototype of the exoskeleton is designed using modern additive technolo-gies. A prototype of the proposed device underwent virtual testing in conditions maximally close to the real one, which confirmed its effectiveness and comfort of use. The main results of the work indicate the promising potential of the proposed solution for application in rehabilitation practice, especially for patients with ankle joint injuries and diseases.

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

This study delves into the dynamic field of medical education research, emphasizing the integration of research training within medical curricula. It seeks to understand the impact of such integration on the competencies of future medical professionals. The primary aim is to systematically categorize and analyze the current trends and future directions in medical education research. This involves assessing the influence of research training on medical students' skills and the methodologies used in such research. Methods: The research employs an extensive bibliographic literature review across multiple databases. It classifies studies into categories like experiential or case studies, editorials, and original research articles. This classification is based on criteria such as geographical location, research objectives, theoretical frameworks, and methodologies. Results: Findings reveal a diverse landscape in medical education research, with a significant emphasis on research training. The research showcases varying methodologies and approaches used globally, highlighting the thematic focus and geographical distribution of these studies. Conclusion: Medical education research is a globally expansive and evolving field. It underscores the importance of continuous investigation, particularly focusing on integrating research elements at curricular levels and exploring innovative educational strategies. The study also points out potential gaps in research, especially in underrepresented regions, indicating directions for future research efforts.

Mpox, formerly known as Monkeypox, is a rare viral disease initially discovered in Africa in 1958. Since its first identification, several outbreaks have occurred in various African nations. Recently, the global community has witnessed a resurgence in the number of Mpox cases reported worldwide, prompting the World Health Organization (WHO) to declare the ongoing multi-country outbreak a public health emergency in July 2022. This study reports on the first cases of Mpox detected in Khartoum State, Sudan, outlining the epidemiology, preparedness, and public health response to this new challenge. A total of 55 suspected cases were identified, with two confirmed cases. The clinical manifestations observed in these cases align with the classic skin rash typical of Mpox, presenting alongside symptoms like fever, headache, and joint pain. The findings underscore the need for heightened surveillance, early detection, and timely intervention to prevent the domestic spread of Mpox and its potential impact on public health. Continued global efforts are needed to support effective screening, diagnostic, and control measures, ultimately enhancing preparedness and response in the face of this emerging disease.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

Cutaneous squamous cell carcinoma is a prevalent malignancy with a rising incidence and notably high mutational load. Exploring the genetic nuances of cSCC and investigating molecular approaches stands as a potential avenue for improving outcome in high-risk patients. This retrospective case-control study involved two cohorts of 14 patients (“discovery cohort”) and 12 patients (“validation cohort”) with cSCC located in head-neck anatomical district and diagnosed at pT2 stage. Overall, cases developed early local relapse of the disease whereas controls never re-lapsed during the entire follow-up period. Next generation sequencing (NGS) approach conducted on histological samples revealed that TP53 and CDKN2A were the most frequently mutated genes in our series. No specific mutation was identified as potential prognostic or therapeutic targets. Controls exhibited a tendency toward a higher mutational rate compared to cases. It is possible that an increased number of mutations could prompt the cSCC to expose more antigens, becoming more immunogenic and facilitating the recognition by the immune system. This could enhance and sustain immunological response, potentially preventing future recurrences.

Background Sarcopenia is a state with progressive and generalized loss of skeletal muscle mass and strength. It is a serious complication occurring in chronic kidney disease (CKD) patients which increases morbidity and mortality rate. Sarcopenia is diagnosed when loss of both compartments - muscle strength and skeletal muscle quality or quantity are present. However, there are still numerous patients, also with CKD, diagnosed as pre-sarcopenic individuals with low muscle strength and normal skeletal muscle quality or quantity and conversely, with correct muscle strength and decreased skeletal muscle mass, who are prone to develop sarcopenia in future life. It is crucial to examine numerous variables possibly associated with changes of skeletal muscle mass and muscle strength in terms of preventing the development of sarcopenia. The aim of the study was to investigate anthropometric and clinical correlates and sources of variation in both skeletal muscle mass and muscle strength in advanced stages of CKD. Methods The study sample consisted of 84 non-dialysis dependent patients of both sexes (including 45.2% of women) with eGFR < 45 ml/min/1.73m²: 26.2% with eGFR 30-44 mL/min/1.73 m², 65.5% with eGFR 15-29 mL/min/1.73 m² and 8.3% with eGFR < 15 mL/min/1.73 m². Muscle strength was estimated by measuring hand grip strength (HGS) with the use of handheld hydraulic dynamometer. Muscle quantity was measured by bioimpedance spectroscopy using Body Composition Monitor. Appendicular skeletal muscle mass (ASM) was calculated according to Lin’s formula. Serum creatinine, urea, uric acid and albumin were measured. Results In bivariate analysis we found that ASM significantly and positively correlated with anthropometric variables such as body mass (r=0.903, p<0.001), NH weight (r=0.882, p<0.001), height (r=0.694, p<0.001), body mass index (BMI) (r=0.701, p<0.001), lean tissue mass (LTM) (r=0.664, p<0.001), lean tissue index (LTI) (r=0.433, p<0.001), fat mass (r=0.614, p<0.001) and fat tissue index (FTI) (r=0.449, p<0.001), and was negatively associated with clinical variable such as hydration status (p<0.001). HGS significantly and positively correlated with anthropometric parameters such as body mass (r=0.319, p=0.003), NH weight (r=0.315, p=0.004), height (r=0.666, p<0.001), LTM (r=0.490, p<0.001), LTI (r=0.238, p=0.029), and ASM (r=0.501, p<0.001), and was negatively associated with clinical variables like uric acid (p=0.039) and urea (p<0.001). After adjustment for age, sex and height, HGS remained significantly and negatively related with uric acid (β=-1.078, p=0.041) and hydration status (β=-0.805, p=0.042). Conclusions In CKD patients, ASM is determined mainly by anthropometric parameters but HGS - both by anthropometric and clinical variables specific for CKD.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

This paper examines the quantitative and qualitative situation of the current fixed and mobile Internet and its expected future. First, the number of users and penetration rate of the Internet, various types of services in different countries, the ranking of countries in terms of the mean and median download and upload Internet data speeds, Internet data volume, and number and location of data centers in the world are presented. The second task introduces and details twelve performance evaluation metrics for broadband Internet access. Third, different wired and wireless Internet technologies are introduced and compared based on data rate, coverage, type of infrastructure, and their advantages and disadvantages. Based on the technical and functional criteria, in the fourth work, two popular wired and wireless Internet platforms, one based on optical fiber and the other based on the 5G cellular network, are compared in the world in general and Australia in particular. Moreover, this paper has a look at Starlink as the latest satellite Internet candidate, especially for rural and remote areas. The fifth task outlines the latest technologies and emerging broadband Internet-based services and applications in the spotlight. Sixthly, it focuses on three problems in the future Internet in the world, namely the digital divide due to the different quality of the Internet and new Internet-based services and applications of emerging technologies, the impact of the Internet on social interactions, and hacking and insecurity on the Internet. Finally, some solutions to these problems are proposed.

Background: The predictive value of changes in C-reactive protein (CRP), procalcitonin and leukocyte levels, which are commonly used in the diagnosis of infection in sepsis and septic shock, remains a topic of debate. This study aims to evaluate the effectiveness of changes in CRP, procalcitonin, and leukocyte counts on the prognosis of patients admitted to the intensive care unit (ICU) with a diagnosis of pneumosepsis and pneumonia-related septic shock, and to investigate whether any of these markers have a superior predictive value over the others in forecasting prognosis. Methods: The study analyzed the demographic data, Charlson Comorbidity Index score (CCIS), CURB-65 score (confusion, uremia, respiratory rate, BP, age ≥ 65 years), and Acute Physiology and Chronic Health Evaluation II (APACHE-II) scores of 230 patients admitted to the ICU with a diagnosis of pneumosepsis and pneumonia-related septic shock between April 1, 2022, and December 31, 2023. The levels of CRP, procalcitonin, and leukocytes were also recorded and analyzed to assess their impact on 1-month and 3-month mortality outcomes. Results: According to multivariate logistic regression analysis, low BMI, male gender, high CCIS, CURB-65, and APACHE-II scores were found to be significantly associated with both 1-month and 3-month mortality (p<0.05). An elevated SOFA score was associated with 1-month mortality, while advanced age was related to 3-month mortality (p<0.05). Although there was no significant relationship between the first-day levels of leukocytes, CRP, and PCT and mortality, their levels on the third day were observed to be at their highest in both 1-month and 3-month mortality cases (p<0.05). Additionally, a concurrent increase in any two or all three of CRP, PCT, and leukocyte values was found to be higher in patients with 3-month mortality compared to those who survived (p=0.004). Discussion: Although PCT, CRP, and leukocyte values measured at the time of admission were not significantly associated with 1-month mortality in patients with pneumosepsis or pneumonia-related septic shock, the persistent elevation and concurrent increase of these values, along with male gender, advanced age, low BMI, and high CCIS, CURB-65, and APACHE-II scores, were found to be significantly associated with 3-month mortality.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&amp;O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&amp;O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

The increased adoption of information and communication technology for smart grid applications will require innovative cyber-physical system (CPS) testbeds to support research and education in the field. The groundbreaking CPS testbeds with realistic and scalable platforms have progressively gained interest in recent years, with electric power flowing in the physical layer and information flowing in the network layer. However, CPSs are critical infrastructures and not designed for testing or direct training, as any misbehaving in an actual system operation could cause a catastrophic impact on its operation. Based on that, it is not easy to efficiently train professionals in CPSs. Aiming to support the advancement and encourage the training of industry professionals, this paper proposes and develops a complete testbed with commercial tools. The testbed can reliably replicate the performance of smart grid systems and the main potential cyber threats that electric grids may face. The complex interdependencies between the cyber and physical domains are discussed in detail, and different case scenarios are presented, providing insightful guidelines for key features and design decisions for future smart grid testbeds.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Background Patients with severe dysphagia are usually fed using a nasogastric tube (NGT). Many patients who receive long-term NGT feeding are unable to obtain sufficient nutrients orally immediately after NGT removal. Thus, a transitional period involving oral diet training is required to transition from NGT feeding to exclusive oral feeding. We aimed to investigate the therapeutic effect of oral diet training in indwelling NGT patients with prolonged dysphagia. Methods A total of 175 patients who were fed using an NGT for more than 4 weeks were enrolled. Their swallowing function was evaluated by a videofluoroscopic swallowing study (VFSS). During the VFSS, patients received thick and thin barium while the NGT was insulted. Then, the patients underwent a VFSS without an NGT thirty minutes after NGT removal. If a patient had no aspiration with NGT inserted during the VFSS, oral diet training combined with NGT feeding was recommended. Results Of the 49 indwelling NGT patients who were recommended to receive oral diet training, 39 (79.6%) transitioned to exclusive oral feeding. A transition period of 2-8 weeks was required for them to achieve full oral feeding. Patients who were eligible for oral feeding trials showed no significant aspiration during the VFSS with an NGT inserted and had sufficient cough function. Patients who required prolonged NGT feeding and who could not complete oral trials showed significant aspiration during the VFSS when an NGT was inserted. Conclusion This study demonstrated that oral diet training combined with NGT feeding was safe in patients with prolonged dysphagia who had sufficient cough function and no aspiration during VFSS. We suggest that if the patient is a proper candidate for NGT removal, direct oral feeding training with an NGT inserted could be a useful therapeutic strategy during the transitional period from long-term NGT feeding to successful oral feeding.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

The main purpose of the study was to study the effects of a specific rowing ergometer training program on the athletic performance of young adolescents (n=56; 11.73 ± 1.4 years old) com-pared to a workout based on general strength training. Eight-week training program was im-plemented, with four sessions per week and two-hours per session. Sample was divided in two groups: a control group (CG) that performed circuit training with exercises aimed at building general strength and an experimental group (EG) who focused on specifically training on a rowing ergometer (rowing machine). The data obtained in a rowing meter test over the compe-tition distance were analyzed to obtain the average power attained (W) at the beginning of the training, at the middle (4 weeks), at the end of the training (8 weeks) and one year after the ex-perimentation. The results show that, although both forms of training improve the average W obtained in both categories, the EG subjects (+29.94W) obtained better averages in all phases of the study compared to the CG (+5.88W). Furthermore, this increase was greater in male rowers (+ 34.06W) than in female rowers (+24.54W). These results reveal that a specific rower rowing ergometer training program has a significant effect than a general strength program and these effects can even be observed a year after the intervention.

The purpose of this longitudinal study was to determine the effects of a rowing training program on physical fitness and body composition in female breast cancer survivors (56.78 ± 6.38 years). Over six months, the participants (n=40) performed two training sessions per week for an average of 75 minutes, combining resistance and muscle strength exercises with rowing. To evaluate the impact of the program, physical fitness tests and anthropometric measurements were carried out before and after the training protocol. The results show statistically significant improvements in measures such as weight (-1.84 kg), BMI (-0.7 kg/m2), hip (-3.24 cm) and waist circumference (-2.45 cm). In addition, variables associated with physical fitness also improved including leg strength (3.04 cm), dominant handgrip strength (4.24 kgf), non-dominant handgrip strength (3.49 kgf), aerobic endurance (78.35 m) and muscle flexibility (3.96 cm). We can therefore conclude that a rowing-based exercise program is an effective strategy to improve physical fitness in this type of population, yielding improvements in both anthropometric measurements and basic physical capacity variables, essential factors for better health and quality of life.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

In contemporary society, digital technology permeates every aspect of our routines. This study assessed students' comprehension of the environmental impacts of prolonged screen time, specifically during binge-watching sessions. It investigated awareness of carbon emissions from electronic device usage, binge-watching habits, and influencing factors such as content preferences, duration, and frequency. The study also explored potential interventions to mitigate environmental impacts. Using a mixed-methods approach, data were collected from 525 higher education students (150 male, 375 female) through self-designed standardized questionnaires. The analysis involved Percentage, t-test, ANOVA, Multiple Correlation, and coding processes. Results indicated that 66.67% of students had a high level of understanding regarding the environmental impact of binge-watching, while only 4.76% were highly aware of the carbon emissions from extended screen time. Additionally, 23.81% exhibited high levels of binge-watching habits and behavior. Gender disparities were significant; females demonstrated a deeper understanding of the environmental impacts (t=4.08, p < α) and showed different binge-watching habits compared to males (t=3.16, p < α). However, no significant gender difference was found in awareness of carbon emissions (t=0.28, p > α). A notable difference (t=12.98, p < α) was observed between students' understanding of environmental impacts and their awareness of carbon emissions. The study also revealed a weak positive correlation (R=0.36) and significant differences [F(2, 1572) = 320.10, p < 0.05, 0.01] in understanding the environmental impacts, awareness of carbon emissions, and binge-watching behaviors. Factors influencing binge-watching and potential regulatory measures were also identified.

Developing effective cognitive training tools for older adults, specifically addressing executive functions such as planning, is a challenging task. It is of paramount importance to ensure the implementation of engaging activities, which must be tailored to the specific needs and expectations of older adults. Furthermore, it is essential to provide the appropriate level of complexity for the planning task. A human-centred approach was employed to address the issues identified in the design of the tool. Two pilot studies were conducted with older adults to fine-tune the training task and optimise its suitability for them. This also led to an enhancement of the underlying planning engine, transitioning from simple fast-forward planner (PDDL4J) to an advanced heuristic search planner (ENHSP). The results show that conducting user studies enabled the development of a cognitive training system that gradually increases the proposed difficulty levels of the planning task while maintaining usability and satisfaction among older adults. This highlights the importance of conducting user studies when implementing cognitive training tools for older adults.

Techniques have been developed to determine whether a horse is in resting or running mode by measuring at least one of the following: the horse's body temperature, heart rate, oxygen saturation, and exercise level. However, the existing technology has not reached a level where a trainer can accurately assess a horse's running conditions, such as speed, acceleration, stride, limb rotation, ground impact, and frontal balance, during the training of racehorses. In addition, data is needed to quickly detect abnormalities during training and provide a basis for changing the intensity of training or deciding to give a rest to the horse. Devices that detect abnormalities in equine gait with high sensitivity will contribute to animal welfare and increase the athletic longevity of horses. This paper reports the development results of a new IoT device that acquires, processes, and analyzes information such as heart rate, position, speed, acceleration, pitch, stride, and ground contact during a training of racehorses. The purpose of this development is to provide an information on a novel processing system, device, method, and program that can analyze training condition of racehorses from multiple angles.

Smartwatches are one of the most relevant fitness trends of the past two decades, and they collect increasing amounts of health and movement data. The accuracy of these data may be questionable and requires further investigation. Therefore, the aim of the present study is to validate smartwatches for use in triathlon training. Ten different smartwatches were tested for accuracy in measuring heart rate, distance (via global navigation satellite systems, GNSS), swim stroke rates and the number of swim laps in a 50 m Olympic-size pool. The optical heart rate measurement function of each smartwatch was compared to that of a chest strap. Thirty participants (15 females, 15 males) ran five 3-minute intervals on a motorised treadmill to evaluate the accuracy of the heart rate measurements. Moreover, for each smartwatch, running und cycling distance tracking was tested over six runs of 4,000 m on a 400 m tartan stadium track, six hilly outdoor runs over 3.4 km, and four repetitions of a 36.8 km road bike course, respectively. Three swimming protocols ranging from 200 m to 400 m were performed in triplicate in a 50 m Olympic-size pool, evaluating tracked distance and detected number of strokes. The mean absolute percentage errors (MAPEs) for the average heart rate measurements varied between 3.1% and 8.3%, with the coefficient of determination ranging from 0.22 to 0.79. MAPE results ranged from 0.8% to 12.1% for the 4,000 m run on the 400 m track, from 0.2% to 7.5% for the 3.4 km outdoor run, and from 0.0% to 4.2% for the 36.8 km bike ride. For the swimming tests, in contrast, the deviations from the true distance varied greatly, starting at a 0.0% MAPE for the 400 m freestyle and reaching 91.7% for the 200 m medley with style changes every 25 m. In summary, for some of the smartwatches, the measurement results deviated substantially from the true values. Measurements taken while road cycling over longer distances with only a few curves were in relative terms more accurate than for outdoor runs and even more accurate than for the 400 m track. In the swimming exercises, the accuracy of the measured distances was severely deteriorated by the medley changes among the majority of the smartwatches. Altogether, the results of this study should help in assessing the accuracy and thus suitability of smartwatches for general triathlon training.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

This study examined the effects of incorporating 8 weeks of biweekly upper limb loaded plyometric training (elastic band) into the in-season regimen of handball players. Trial participants were assigned between control (n = 15, age: 18.1±0.5 years, body mass: 73.7±13.9 kg) and experimental (n = 14, age: 17.7±0.3 years, body mass: 76.8±10.7 kg) groups. Measures obtained pre- and post- included a cycle ergometer force-velocity test, ball throwing velocity in three types throw, 1-RM bench press and pull-over, and anthropometric estimates of upper limb muscle volumes. Gains in the experimental group relative to controls included absolute muscle power (W) (Δ23.3%; t-test p<0.01; d=0.083), relative muscle power (W.kg-1) (Δ22.3%; t-test p<0.01; d=0.091), and all 3 types of ball throw (Δ18.6%, t-test p<0.01, d=0.097 on jumping shot; Δ18.6%, t-test p<0.01; d=0.101 on 3-step running throw; and Δ19.1%, t-test p<0.01, d=0.072 on standing throw). Furthermore, a significant improvement by time interactions was observed in both groups on 1-RM bench press and pull-over performance. However, upper limb muscle volumes remained unchanged in both groups. We conclude that adding biweekly elastic band plyometric training to standard training improves measures important to game performance. Accordingly, such exercises can usefully be adopted as a part of handball training.

The prolonged static sitting at the workplace is considered as one of the main risks for development of musculoskeletal disorders (MSDs) and adverse health effects. Factors such as poor posture and extended sitting are perceived to be a reason for conditions such as lumbar hyperlordosis and lower back pain (LBP), even though the scientific explanation of this relationship is still unclear and raises disputes in the scientific community. This publication proposes the low back pain assessment (LBPA) dataset collected through experiment with 100 participants and consisting of photogrammetric images with intentionally placed body markers, calculated postural angles and tags correct and incorrect posture assessed by habilitated rehabilitator, as well as questionnaire-based self-reports regarding the occurrence of LBP and similar symptoms among the participants. Machine learning models trained with this data are employed for recognizing incorrect body postures. Two scenarios have been elaborated for modeling purposes: scenario 1, based on natural body posture tagged as correct and incorrect, and scenario 2, based on incorrect body postures, corrected additionally by the rehabilitator. The achieved accuracies of respectively 75.3% and 85% for both scenarios reveal the potential for future research in enhancing awareness and actively managing posture-related issues that elevate the likelihood of developing lower back pain symptoms.

Objectives: This study aimed to compare the similarities and differences between the Kawasaki disease (KD) during the SARS-CoV-2 pandemic and multisystem inflammatory syndrome in children (MIS-C). Methods: The medical records of patients diagnosed with KD and MIS-C at a single center between July 2020 and November 2021 were retrospectively reviewed. Results: The study included 39 MIS-C patients (84.6% male) with a median age of 138 months and 17 KD patients (58.8% male) with a median age of 36 months. Compared with the KD patients, MIS-C patients were older (p<0.001), had longer hospital stays (p=0.023), elevated neutrophil count (p<0.001), C-reactive protein (p<0.001), procalcitonin (p<0.001), interleukin-6 (p<0.014), ferritin (p<0.001), fibrinogen (p<0.001), troponin I (p=0.001), NT-proBNP (p<0.001), and, D-dimer levels (p<0.001). They had more hypotension (p=0.024), decreased left ventricular function (p=0.023), and a greater need for corticosteroids (p<0.001), enoxaparin (p=0.045), and therapeutic plasma exchange (p<0.001). Patients with KD displayed a higher frequency of rash (p<0.001), oral mucosal changes (p<0.001), conjunctival injection (p<0.001), extremity changes (p<0.001), and cervical lymphadenopathy (p<0.001). They had a longer duration of fever (p<0.001), elevated white blood cell count (p<0.001), platelet count (p<0.001), and alanine aminotransferase level (p<0.001). The two groups were similar in terms of hemoglobin levels, erythrocyte sedimentation rate, albumin levels, or the frequency of coronary dilation/aneurysm, myocarditis, pericarditis, invasive mechanical ventilatory support, and intravenous immunoglobulin treatment. Conclusions: Older patient age, a greater presence of gastrointestinal and cardiac findings associated with hypotension, increased NT-proBNP levels, decreased left ventricular function, the use of various treatment modalities, and longer hospital stays suggest MIS-C, whereas a longer duration of fever and classical clinical features of KD favor KD.

As cardiovascular diseases continue to be a leading cause of mortality, recent-ly, wearable devices for monitoring cardiac activity have gained much interest among medical community. This paper introduces an innovative ECG monitoring system based on a single – lead ECG machine enhanced with machine learning methods. The system only processes and analyses the ECG data, but also predict potential heart disease at an early stage. The wearable device was built on the ADS1298 and a microcontroller STM32L151xD. A server module based on REST API architecture style was designed to fa-cilitate interaction with web-based segment of the system. The module is responsible for receiving data in real time from microcontroller and their deliver to web – based segment. Algorithms for analyzing ECG signals have been developed, including band filter artifact removal, K-means clustering for signal segmentation, and PQRST analysis. Machine leaning methods as Isolation Forest have been employed for ECG anomaly detection. Moreover, a comparative analysis with various machine learning methods, including lo-gistic regression, random forest, SVM, XGBoost, decision forest and, CNNs was conducted to predict cardiovascular diseases. Convoluted Neural Networks (CNN) showed an accu-racy of 0.926, proving high effectiveness in ECG data process.

The aim of our study was a comprehensive comparative assessment of the effect of consumption of 1 and 2% cholesterol as part of a standard diet with and without regular moderate physical activity on the main biomarkers of lipid and cholesterol metabolism, as well as the intestinal microbiota of male Wistar rats. The animals were randomly divided into 5 groups according to body weight and Open Field test results: Control (n=10), 1% Chol (n=10), 2% Chol (n=10), 1% Chol + RUN (n=10) and 2% Chol + RUN. The cholesterol was additionally added in the amount of 1g or 2g/100g, respectively, to the diet of animals. The rats of experimental groups 1% Chol + RUN and 2% Chol + RUN were subjected to regular (2 days a week) physical activity on a Treadmill. In rats of four experimental groups, when compared to the Control, a response of 39 indicators was revealed. The largest number of changes in biomarkers - 29 (statistically significant, p

With the rapid growth of large language models (LLMs), there is increasing demand for memory and computation in LLMs. Recent efforts on post-training pruning of LLMs aim to reduce the model size and computation requirements, yet the performance is still sub-optimal. In this paper, we present a plug-and-play solution for post-training pruning of LLMs. The proposed solution has two innovative components: 1) Relative Importance and Activations (RIA), a new pruning metric that jointly considers the weight and activations efficiently on LLMs; and 2) Channel Permutation, a new approach to maximally preserve important weights under N:M sparsity. The two proposed components can be readily combined to further enhance the N:M semi-structured pruning of LLMs. Our empirical experiments show that RIA alone can already surpass all existing post-training pruning methods on prevalent LLMs, e.g., LLaMA ranging from 7B to 65B. Furthermore, N:M semi-structured pruning with channel permutation can even outperform the original LLaMA2-70B on zero-shot tasks, together with practical speed-up on specific hardware. Our code is available at: https://github.com/biomedical-cybernetics/Relative-importance-and-activation-pruning

This study investigates by hybrid approach of classical calculations and numerical explicit FEM simulation the strain rate sensitive hardening of Polypropylene Sabic 83MF10 under dynamic tension loads. The Cowper-Symonds model is employed to characterize the non-linear increase in yield strength with strain rate, within the range of 0,01 to 1 [1⁄s]. For lower strain rates, a drastic decrease in yield strength is observed, suggesting the significant influence of creep and relaxation phenomena. The study proposes further research incorporating viscoelastic properties for a more comprehensive material model. Additionally, the study observes a disproportionate increase in yield strength for samples with smaller radius, indicating a dependency on triaxiality which suggests further research on the Drucker-Prager model for this material. The study concludes by recommending a broader range of input parameters for future studies, including the Johnson-Cook model and comparison of tensile test results with compression test results.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (&gt;0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

This study aims to investigate whether 16 weeks of High-Intensity Interval Training (HIIT) implemented on Physical Education classes (PEC), can improve physical fitness in high-school adolescents This study was a two-arm randomized controlled trial design with adolescents (15-17 years old). Twelve classes were randomized to either a 16 weeks of HIIT (HIIT-G, n = 106 students) implemented on PEC warm-up or a control group (CG, n = 123 students) of usual PEC warm-up. The HIIT sessions ranged from 14 to 20 all-out bouts intervals, adopting a 2:1 work-to-rest ratio. Post-intervention measures revealed a significant difference between groups in CRF and girls from HIIT-G increased their cardiorespiratory fitness (CRF) with significant difference between female groups and a medium to large effect size. The main findings from this study indicate that brief whole-body HIIT of an extremely low volume, over 16 weeks, can improve CRF in adolescent girls.

Evidence suggests that COVID-19 infection can cause lasting health consequences. Multidiscipli-nary rehabilitation services have been recommended to reduce the sequalae. However, the effec-tiveness of physical exercise interventions remains insufficiently documented. The aim of this study was to develop and implement a specific and well tolerated protocol-based, intervention to reduce muscle weakness in older adults impacted by COVID-19. Forty six older adults random-ized into Intervention and Control Groups. Isometric and isokinetic strength assessments were conducted for selected muscle groups using JBA Staniak® torquemeter and Biodex System 3 dy-namometer. Functional abilities were evaluated with the Time Up and Go test and Chair Stand Tests. Men in intervention group demonstrated a significant improvement in static conditions for knee flexors (KF), trunk extensors (TE) and trunk flexors (TF) and in dynamic conditions for knee extensors (KE). Women in intervention group showed significant improvement in static condition for EF, KF, TE and TF and in dynamic for a KE and for a KF. The interaction GROUP x TESTING SESSION was significant for Chair test (s) and Chair test (n). Our results demonstrate the effec-tiveness of a well-tolerated, protocol-based approach that can be used to diminish long lasting functional deficits in post-covid survivors.

Rift Valley fever (RVF) is a mosquito-borne zoonotic viral disease that infects both human and animals. This is a descriptive study summarizes investigation and response to RVF outbreak, using surveillance data. A RVF outbreak occurred in Berber locality in northern Sudan. We identified 246 cases of RVF including seven deaths among humans, 119 deaths and 82 abortions among Livestock. Our entomological surveillance confirmed the presence of Anopheles arabiensis, An. stephensi, Aedes aegypti, Ae. vexans, Culex pipiens, Cx. Quinquefasciatus, and Cx. theileri in the area during the outbreak. In a comparison with another outbreak of Rift Valley fever in nearby area while ago, a multisectoral One Health response strategy has resulted in strengthening the health system through re-innovating health facilities and centres and training about 200 healthcare and emergency responders. Additionally, it reduced cases and fatalities among humans by 78% and 63%, respectively, and loss in livestock due to deaths and/or abortions by 82%. The added-value of implementing One Health strategy was saving more lives and resources, while strengthening the health system. We recommend the systematic institutionalization of One Health strategy in the country as a core part of the national prevention and control strategy for zoonotic diseases epidemics and pandemics.

Sialyllactose (SL) is a functional human milk oligosaccharide essential for immune support, brain development, intestinal maturation, and antiviral defense. However, despite its established health benefits, the effect of SL on exercise performance and muscle mass in mice remains unknown. Here, we aimed to investigate, for the first time, the effects of 6′-SL on muscle functions. Seven-week-old male C57BL/6J mice were administered 100 mg/kg 6′-SL for 12 weeks, after which exhaustive treadmill performance, muscle strength, and muscle phenotype were examined. The administration of 6′-SL significantly improved exhaustive treadmill performance metrics, including distance and exhaustion time. Grip strength was also increased by 6′-SL administration. Additionally, 6′-SL increased muscle mass in both the gastrocnemius (GAS) and soleus. 6′-SL administration led to an increase in the minimum Feret’s diameter and the protein expression of total myosin heavy chain in the GAS muscle. In conclusion, 6′-SL administration in vivo led to increased running distance and time by increasing muscle mass and strength. These findings collectively indicate that 6′-SL is a potential agent for improving muscle health and exercise performance.

Dynamic sparse training is an effective strategy to alleviate the training and inference demands of artificial neural networks. However, current sparse training methods face a challenge in achieving high levels of sparsity while maintaining performance comparable to that of their fully connected counterparts. The Cannistraci-Hebb training (CHT) method produces an ultra-sparse advantage compared to fully connected training in various tasks by using a gradient-free link regrowth method, which relies solely on the network topology. However, its rigid selection based on link prediction scores may lead to epitopological local minima, especially at the beginning of the training process when the network topology might be noisy and unreliable. In this article, we introduce the Cannistraci-Hebb training soft rule (CHTs), which applies a flexible approach to both the removal and regrowth of links during training, fostering a balance between exploring and exploiting network topology. Additionally, we investigate the network topology initialization using several approaches, including the bipartite scale-free and bipartite small-world network models. Empirical results show that CHTs can surpass the performance of fully connected networks with MLP architecture by using only 1% of the connections (99% sparsity) on the MNIST, EMNIST, and Fashion MNIST datasets and can provide remarkable results with only 0.1% of the links (99.9% sparsity). In some MLPs for image classification tasks, CHTs can reduce the active neuron network size to 20% of the original nodes (neurons), demonstrating a remarkable ability to generalize better than fully connected architectures, reducing the entire model size. This represents a relevant result for dynamic sparse training. Finally, we present evidence from larger network models such as Transformers, with 10% of the connections (90% sparsity), where CHTs outperform other prevalent dynamic sparse training methods in machine translation tasks.

Aim: Ovarian cancer is the leading cause of gynecological cancer deaths worldwide. Treatment methods are listed as surgery, chemotherapy and radiotherapy depending on the stage of the cancer, but developing resistance to chemotherapy increases the need for alternative agents that act on the same pathways. In this study, the effects of rosmarinic acid (RA) and doxorubicin (DX) on the activation of FOXP3, an important tumor suppressor gene, in OVCAR3 cells were examined. Material Method: In the study, human ovarian adenocarcinoma cell line was used. MTT test was applied to determine the effect of rosmarinic acid and doxorubicin on the proliferation of OVCAR3 cells. Expression levels of FOXP3 for cell proliferation and Capase-3 for Apoptosis were determined by qRT-PCR and Western blot analysis. Wound healing model was applied to determine metastasis. The results were evaluated with one-way ANOVA in SPSS 20.0 program as p≤0.05. Results: It was determined that rosmarinic acid alone and in combination with doxorubicin inhibited the proliferation of OVCAR3 cells in a time- and dose-dependent manner for 24, 48 and 72 hours, and caused the cells to die by causing them to undergo apoptosis. It was observed that Caspase-3 expression increased approximately tenfold in OVCAR3 cells, while FOXP3 expression increased only in RA treatment and was downregulated in DX and RA+DX treatments. Coclusion According to the results of our study, it was observed that many steps of the signaling pathways related to proliferation, migration and apoptosis were affected by the combination of RA and DX in OVCAR3 cells. This shows that RA will gain an important place in cancer treatment with more comprehensive studies.

Aim: Ovarian cancer is one of the most frequently diagnosed cancers in women in the world. Recognition of the differences between tumors in cancers and resistance to treatment in patients have made the treatment potential of chemotherapy, radiotherapy and immunotherapy controversial. Especially against drug resistance, laboratories have implemented the drug diversion system by putting old drugs into new forms. In this study, the cytotoxic and apoptotic effects of the combination of doxorubicin (DX) and thymoquinone (TQ) on ovarian adenocarcinoma cells (OVCAR3) were investigated. Material Method: OVCAR3 cell line was cultured in RPMI medium containing 10% FBS, 1% penicillin/streptomycin. Cell viability and cell growth rate were determined by MTT viability test by combining doxorubicin and thymoquinone. Nucblue immunofluorescent staining was used to determine the mechanism of cell death at different doses of doxorubicin and thymoquinone compounds, qRT-PCR to determine the pathways underlying the apoptotic mechanism, and western blot methods to show protein levels. Result: We found that the combination of DX and TQ reduced the viability of OVCAR3 cells (MTT assay), induced apoptosis (RAF, RAS, Bcl2, Bax by qRT-PCR) and increased RAF, RAS protein levels in TQ and DX-treated cells by western blot analysis. Conclusion: The results obtained revealed for the first time that combining DX and TQ also had cytotoxic/apoptotic and anti-proliferative effects against ovarian adenocarcinoma cells.

The implementation of cybersecurity standards and directives in the maritime sector plays a crucial role in protecting critical maritime infrastructures from cyber threats. The level of protection depends heavily on humans. However, the effectiveness of cybersecurity training and compliance programs, an essential component of these standards, is often hindered by challenges related to the sector’s environment, including the established technologies, practices, and norms. This paper aims to identify these challenges through a literature review and set the basis for more effective human risk minimisation, responses, and training. We identify 18 challenges and validate them with an online survey (N=205) capturing real-world perspectives from maritime-related stakeholders. Our findings contribute to enhancing the effectiveness of maritime cybersecurity training and compliance programs, ultimately strengthening the maritime cybersecurity posture.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

Deep Eutectic Solvents (DESs) show promising abilities for the delamination of multilayer packaging films that are used in food packaging and in pharmaceutical blister packs. Due to the complexity of their structure, the recycling of these materials is a challenging task, leading to the easiest or cheapest option, landfilling. Towards the development of ‘green’ solvents for the efficient waste management and recycling, the conducted research focuses on the preparation of a range of hydrophobic and hydrophilic DES based on carboxylic acids. Also, their chemical and physical characterization, such as DSC, rheometer and density measurements, was followed for the determination of their properties. The laminate packaging waste products that were tested were Al/PE, PE/Al/PET, Al/PE/paper and PVC/PE/Al. Different batches of solvent systems were tested based on various naturally derived aliphatic and aromatic organic compounds as well as amino acids. The separated films were collected and studied further for the examination of the delamination extend. Results showed full or partial delamination of some materials as well as challenges of solvent systems. Variables such as temperature, agitation rate, mixing time and solvents ratios were monitored and collected during the design of experimental process. The results showed that the used DESs can offer an efficient, low-energy, affordable and green option for the delamination tested packaging materials.

The present exploratory study tested the hypothesis that computerized cognitive training (CCT) in home telemonitoring may beneficially affect eyes-closed resting-state electroencephalographic (rsEEG) rhythms in Parkinson's disease patients with cognitive deficits (PDCD). A Eurasian database provided clinical-demographic-rsEEG datasets in 40 PDCD patients, 29 PD patients without cognitive deficits (PDNCD), 40 Alzheimer’s disease patients with cognitive deficits (ADCD), and 40 cognitively normal older adults (Healthy). Sixteen of the 40 PDCD patients completed a cross-over unsupervised CCT program of simple, serious video games (versus a sham program) consisting of 14 daily sessions of approximately 20 minutes each in the patients' homes. Compared to the Healthy, PDNCD, and ADCD groups, the PDCD group was characterized by greater diffuse rsEEG delta (about 2-4 Hz) and theta (about 4-7 Hz) source activity. The PDCD patients who underwent the CCT program showed an improvement in video game performance and a reduction in these delta-theta source activities after this program compared to the control condition. In conclusion, these results suggest that the 2-week CCT program in home telemonitoring may mitigate the abnormal “slowing” of rsEEG rhythms in PDCD patients, possibly enhancing the regulation of brain arousal and quiet vigilance.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.