Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Plant growth regulators (PGRs) and deficit irrigation (DI) play a crucial strategic role in sustaining agricultural yield and reducing water stress in drought prone areas. The study was carried out in 2021-2022 to assess the impact of various PGRs (SA & NAA) & irrigation levels (60% Epan, 80 % Epan, and 100 % Epan) with DI & partial root drying (PRD) irrigation strategies. PGR application boosted fruit yields and demonstrated its significance in reducing water stress by lowering canopy temperature, maintaining higher relative water content in the leaves, modifying stomatal opening, and increasing photosynthetic rate. PGRs were used to assess the increased accumulation of total phenols, flavonoids, and improved antioxidant activity. Results indicated that exogenous use of PGRs like SA+NAA in conjunction with 80% irrigation levels increased fruit yield (31.97 and 40.38%) and water productivity (64.92 and 75.39%) for DI and PRD treatments, respectively. Thus standardizing irrigation and crop management practices including PGR application can be recommended to boost pomegranate productivity particularly in water-scarce environments.

An analysis of the processes of plastic deformation and acoustic relaxation in a high-entropy alloy Al0.5CoCrCuFeNi was carried out. The following have been established: dominant dislocation defects; types of barriers that prevent the movement of dislocations; mechanisms of thermally activated movement of various elements of dislocation lines through barriers at room and low temperatures. Based on modern dislocation theory, quantitative estimates have been obtained for the most important characteristics of dislocations and their interaction with barriers.

Phosphite (Phi) has gained attention in agriculture due to its biostimulant effect on crops. This molecule has been found to benefit plant performance by providing protection against pathogens, improving yield and fruit quality, and improving nutrient and water use efficiency. It is still unclear how Phi enhances plant growth and protects against multiple stresses. It has been hypothesized that Phi acts by directly affecting the pathogens and interacting with the plant cellular components and molecular machinery to elicit defense responses. This study delves into elucidating the mechanisms underlying Phi’s beneficial effects on plants, revealing a complex interplay with fundamental signaling pathways. A RNA-seq study of Arabidopsis seedlings under optimal and limiting phosphate conditions helped us unveil Phi’s role in promoting plant growth by activating the expression of genes involved in the biosynthesis and signaling pathways associated with abscisic acid (ABA), salicylic acid (SA), and jasmonic acid (JA). Expression of ABA-related genes, known for their involvement in stress response and development regulation, is triggered by Phi treatment, contributing to enhanced resilience and growth. Simultaneously, the activation of the SA pathway, associated with defense responses, suggests Phi’s potential in bolstering plant immunity. Moreover, Phi influences JA biosynthesis and signaling, which are crucial for defense against herbivores and pathogens, thereby strengthening plants’ defenses. Our findings reveal a multifaceted mechanism through which Phi benefits Arabidopsis development. Understanding its intricate interplay with key signaling pathways opens avenues for leveraging Phi as a strategic tool to enhance plant resilience, immunity, and growth in agricultural and ecological contexts.

To enhance pomegranate production on marginal gravelly lands, standardized planting techniques were evaluated in an 8-year-old orchard. Trenching, wider pit excavation, pit digging, and auger digs with dimensions of 1 and 2 m were employed. Utilizing native soil from barren land, with or without spent wash, and mixing it with black soil up to 1 m deep, growth parameters, leaf nutrients, fruit production, and fruit quality were assessed. The trench and wider pit methods outperformed others, yielding greater above-ground biomass (>70.3 kg tree⁻¹), root biomass (>24.5 kg, tree⁻¹), and cross-sectional area (>3.30 m² tree⁻¹). These methods also produced longer roots (>4.0 m tree⁻¹) and higher leaf phosphorus (>0.28%) and potassium (>1.81%) levels, fruit juice content (>48.50%), and total soluble solids (>16.05°) compared to other planting methods. This resulted in higher and more sustainable fruit yield production under the trench and wider pit planting methods (>7.21 t ha⁻¹). Similarly, the native and black soil mixture produced healthy fruit trees, improved fruit quality, and sustainably higher fruit yield over the native soil alone. In summary, the trench and wider pit methods (2–3 m³), combined with a soil mixture, are recommended for sustainable, high-quality fruit production in shallow gravelly terrains, thereby improving food security and the livelihoods of farmers in arid regions.

Detection methods have been developed to prevent transmission of zoonotic or xenozoonotic porcine viruses after transplantation of pig organs or cells to the recipient (xenotransplantation). Eleven xenotransplantation-relevant viruses including porcine cytomegalovirus, a porcine roseolovirus (PCMV/PRV), porcine lymphotropic herpesviruses -1, -2, -3 (PLHV-1, 2, 3), porcine parvovirus (PPV), porcine circovirus 2, 3, 4 (PCV2, 3, 4), hepatitis E virus genotype 3 (HEV3), porcine endogenous retrovirus-C (PERV-C) and recombinant PERV-A/C have been selected. In the past, several pig breeds, minipigs and genetically modified pigs generated for xenotransplantation had been analyzed using these methods. Here, spleen, liver and blood samples from 10 German slaughterhouse pigs were screened using both, PCR-based and immunological assays. Five viruses: PCMV/PRV, PLHV-1, PLHV-3 and PERV-C were found in all animals, and PCV3 in one animal. Some animals were latently infected with PCMV/PRV as only virus-specific antibodies were detected. Others were also PCR positive in spleen and/or liver, indicative of an ongoing infection. These results provide important information on the viruses that infect German slaughterhouse pigs and together with results of previous studies revealed that the methods and test strategies efficiently work under field conditions.

The study delves into the Zaalklapspruit valley-bottom wetland in South Africa, a site designed through ecological engineering and currently impacted by acid mine drainage due to an upstream defunct coal mine. The research conducted in 2022, aimed to uncover the dynamics of contaminant dispersal within such a wetland setting, focusing on the origins, routes, and ultimate recipients of various metals and sulfur compounds. Analysis revealed that the bottom sediment is rich in organic material, with pH levels observed between 6.05 and 6.59, and exhibited notably low oxidation-reduction potentials, reaching down to −219.67 mV at sample point S3. Notably, Manganese displayed the highest adsorption rates, whereas Iron was predominantly absorbed by the roots of Typha capensis and the algae Klebsormidium acidophilum. The wetland's macrophyte rhizospheres hosted a rich array of microbiota, including families like Helicobacteraceae and Hydrogenophilaceae, which are crucial in metal and sulfur processing. This investigation sheds light on the intricate biogeochemical processes taking place involving the wetland's sediment, macrophyte root systems, periphyton, and microbial populations, underscoring the potential of ecologically engineered wetlands in the remediation of waters affected by acid mine drainage.

We examine worldwide Property and Casualty and Life and Health insurance companies from 2004 until 2023, implementing panel regression models and mediation analysis to show that insurers raise their reserves when they face increasing costs for their potential environmental damages, ultimately reducing their profitability and underwriting capacity. Our findings extend to the insurance sector the previous evidence on banks, demonstrating that environmental damages could affect profits and solvency of financial intermediaries. These insights are important especially for insurance managers and regulators.

Ectopic expression of the MYB transcription factor of AmROSEA1 from Antirrhinum majus has been reported to change anthocyanin and other metabolites in several species. In this study, we found that overexpression of AmRosea1 significantly improved the tolerance of transgenic rice to drought and salinity stress. Transcriptome analysis revealed that a considerable amount of stress-related genes were affected by exogenous AmRosea1 during both drought and salinity stress treatments. These affected genes are involved in stress signal transduction, the hormone signal pathway, ion homeostasis and the enzymes that remove peroxides. This work suggests that the AmRosea1 gene is a potential candidate for genetic engineering of crops.

Bacillus amyloliquefaciens GL18 has been proven to have good resistance ability and can promote the growth of Avena sativa cultivar ‘Qingyan 1’. Herein, Illumina high-throughput transcriptome sequencing technology was used to analyze the differential expression of genes between the interaction group (LB) and the control group (LCK) when ‘Qingyan 1’ roots interacted with GL18 bacterial suspension or sterile water for 12 h under 4 °C low-temperature stress. The gene function annotation information was obtained using Gene Ontology (GO) functional classification and enrichment analysis. Kyoto Encyclopedia of Genes and Genomes (KEGG) pathway enrichment analysis and annotation of differentially expressed genes was used to explore the related signal transduction pathway of ‘Qingyan 1’ response to cold stress induced by Bacillus GL18. The results showed that after ‘Qingyan 1’ seedlings interacted with GL18 bacterial suspension or sterile water for 12 h, comparing the LB with the LCK or CK (the control group at 26 °C), there were 12,061 and 25,489 differentially expressed genes, respectively. Their functions were mainly related to metabolic process, cellular process, catalytic activity, binding, and cellular parts, and they were significantly enriched in plant tissue growth and development, cell wall, organelle membrane synthesis, thiamine and its compounds, biosynthesis, polyamine decomposition, and other metabolic processes. Signal transduction was detected through KEGG pathway enrichment analysis, and corresponding genes, such as AUXI, PP2C, SNRK2, ABF, BRI1, and PIF4, were expressed. The expression of genes directly involved in plant growth was upregulated in the presence of GL18, as shown by real-time quantitative PCR analysis. It was speculated that the normal growth and development of ‘Qingyan 1’ under low-temperature stress promoted by GL18 is a result of the integration of multiple pathways in terms of regulating endogenous hormone metabolism, secondary metabolite synthesis, and photosynthesis.

The symmetry properties of an ornament contain information about its civilisation and its interactions with other cultural sources. Two-dimensional periodic ornaments can be strictly classified into a limited set of 17 mathematical symmetry groups, also known as wallpaper groups. The collection of ornaments thus classified for a civilisation is characteristic of the cultural group and serves as a fingerprint to identify that group. If the distribution of wallpaper groups is available for several societies, mathematical methods can be applied to determine similarities and differences between the art practices of these communities. This method allows a systematic approach to the general ornamental practices within a culture and their interactions in the form of similarity of fingerprints. We test the feasibility of the method on examples of medieval Armenians, Byzantium, Seljuks first in Persia and then in Anatolia and among Arabs in the Middle East. For this purpose we present the distribution of the planar ornaments and calculate the Euclidean distances in pairs. We tested to what extend geographical and religious factors could account for the observed similarity of ornamental groups between cultures. The results suggest an intensive interaction between the Seljuk Turks and Arab craftsmen who produced the ornaments. Therefore the cultural interactions are religiously motivated.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

High temperature stress affects tomato production both in tropical and sub-tropical environments worldwide. To explore genetic variation for heat tolerance in tomato, 329 transcontinental tomato varieties were evaluated at The Ministry of Municipality and Environment (MME) greenhouses near Doha, Qatar. Preliminary phenotypic analysis identified a diverse set of 71 hybrid and pure line tomato varieties for more detailed studies. The selected subset was examined in the greenhouse in a randomized complete block design under heat stress. The materials were phenotyped for fruit size, fruit weight, fruit hardness, fruit locules, fruit set (%), total soluble solids (TSS), and fruit yield. Significant phenotypic differences among genotypes were observed for all the traits assessed. To explore the genetic basis of variation among varieties the subset was genotyped using 104 SNP markers identified in previous heat tolerance genome wide association studies (GWAS). Nineteen QTL associated SNP markers could reliably select heat tolerant varieties in terms of better fruit yield, fruit set, and TSS. These markers are located on Chromosome 1, 5, 6, 8, 9, and 12. Interestingly, two clusters of markers on chromosome 6 were linked to significant effects on yield, fruit set, and TSS under high temperature. Some markers located within these QTL regions were also reported as associated with heat tolerance in other studies. Eighteen out of nineteen SNP markers were mapped within a gene body. Based on the phenotypic and the genotypic analysis, an elite set of five varieties was selected for approval for heat stress environments in Qatar. These findings have significance not only for Qatar, but they are also valuable for wider application at other locations worldwide. The 19 markers presented here could be adopted by breeders for marker-assisted selection (MAS) for heat tolerance.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

The purpose of this study was to elucidate patterns and mechanisms driving seasonal and inter-annual variations of carbon and nitrogen stable isotopes in the zooplankton crustacean commu-nity of Lake Maggiore (Italy), during the period 2009-2020. Different zooplankton taxa and groups revealed different ranges of d13C signatures, giving an insight into food sources and niche partition. In particular, cyclopoids had a restricted range with most negative d13C‰ values and increase in d13C fractionation with the establishment of water thermal vertical stratification, high-lighting the importance of vertical distribution as key factor for taxa coexistence in a vertically heterogenous environment. d13C of the zooplankton community and of Daphnia were positively related to water temperature (R2=0.58 p <0.0001 and R2=0.68 p <0.0001, respectively) and d13C Daphnia signature to chlorophyll-a (R2=0.32, p < 0.0001). Decomposition of time series data for zooplankton carbon and nitrogen signatures and environmental parameters identified increasing trends in water temperature, chlorophyll-a and water conductivity and decrease in nitrate, that matched changes in carbon isotopic signature trend in some zooplankton taxa (Bosmina, Daphnia and diaptomids). Overall, the observed patterns in zooplankton isotopic signatures were interpreted as integrations of climate warming effects in Lake Maggiore, affecting both food sources availability and environmental conditions.

Background: The COVID-19 pandemic led to rapid growth in telemental health services and investment in digital mental health technologies. Digital mental health technologies could expand access to mental health care amid increasing provider deficit by providing tools for expedited psychiatric symptom assessment and treatment augmentation. This systematic review explores the recent evidence for the use of scalable digital tools, including virtual reality, neurofeedback training, wearables, mobile apps, digital phenotyping, and machine learning for PTSD symptom assessment, diagnosis, and treatment. Methods: A PubMed search identified studies on digital technologies with current or future potential for scalability (accessible through a small, digital device without the virtual or in-person presence of a mental health care provider)–and PTSD diagnosis, symptom assessment, or symptom treatment as the primary outcome. Thirty-five studies inform this review. Results: Virtual reality exposure therapy is efficacious for combat-related PTSD treatment. Conclusions of studies investigating apps and neurofeedback training are limited by low sample size and methodological heterogeneity. Machine learning models demonstrate capability in detecting PTSD symptoms via passively collected data from smartphones, wearables, and actively collected data from patient speech, writing, and videos, but standardization of data collection and modeling are needed before application to clinical settings. Conclusions: Advancements in scalable digital tools could address barriers in healthcare access and improve patient engagement by providing asynchronous assessment and treatment augmentation. Future research utilizing diverse patient populations in standardized controlled trials is needed to determine evidence-based protocols for implementation.

Climate change has emerged as a crucial global issue that significantly threatens the survival of plants. In particular, low temperature (LT) is one of the critical environmental factors that influence plant morphological, physiological, and biochemical changes during both the vegetative and reproductive growth stages. LT, including abrupt drops in temperature, as well as winter conditions, can cause detrimental effects on the growth and development of tomato plants, ranging from sowing, transplanting, truss appearance, flowering, fertilization, flowering, fruit ripening, and yields. Therefore, it is imperative to understand the comprehensive mechanisms underlying the adaptation and acclimation of tomato plants to LT at the morphological and the molecular levels. In this review, we discuss the previous and current knowledge of morphological and physiological changes, which contains major factors and traits associated with the LT stress response during the period of the vegetative and reproductive growth and development in tomato plants. Moreover, we highlight recent advances in the understanding of physiological and biochemical responses, and molecular mechanisms, including LT perception, signaling transduction, gene regulation, and fruit ripening and epigenetic regulation. The comprehensive understanding of LT response provides a solid basis to develop the LT-resistant varieties for sustainable tomato production under the ever-changing temperature fluctuations.

Ferulic acid esters have been suggested as a group of natural chemicals with sunscreen function. The study aimed to utilize an environment-friendly enzymatic method to produce octyl ferulate by esterification of ferulic acid with octanol. The Box-Behnken design with response surface methodology (RSM) was adopted to evaluate the effects of synthesis variables, including reaction temperature (70–90 °C), enzyme amount (1000–2000 PLU) and stir speed (50–150 rpm), on the molar conversion of octyl ferulate. According to the joint test, both the reaction temperature and enzyme amount had great impacts on the molar conversion. RSM-developed second-order polynomial equation further showed great ability on data-fitting. Based on ridge max analysis, the optimum parameters for the biocatalyzed reaction were: 72 h reaction time, 92.2 °C reaction temperature, 1831 PLU enzyme amount and 92.4 rpm stir speed, respectively. Finally, the molar conversion of octyl ferulate under optimum condition was verified to be 93.2 ± 1.5%. In conclusion, high yield of octyl ferulate synthesized by commercial immobilized lipase under elevated temperature conditions has been suggested, which our findings could broaden the utilization of the lipase and provide a biocatalytic approach, instead of the chemical method, for ferulic acid ester synthesis.

Rice production, owing to its high-water requirement for cultivation, is very vulnerable to the threat of changing climate, particularly prolonged drought and high temperature. Such threats heighten the need for abiotic stress-resilient rice varieties with better yield potential. This review examines the physiological and molecular mechanisms of rice varieties to cope with stress conditions of drought (DS), high temperature (HTS) and their combination (DS-HTS). It appraises research studies in rice about its various phenotypic traits, genetic loci and response mechanisms to stress conditions to help craft new breeding strategies for rice varieties with improved resilience to abiotic stresses. This review consolidates available information on promising rice cultivars with desirable traits as well as advocates synergistic and complementary approaches in molecular and systems biology to develop new rice breeds that favorably respond to climate-induced abiotic stresses. The development of new breeding and cultivation strategies for climate-resilient rice varieties is a challenging task. It requires a comprehensive understanding of the various morphological, biochemical, physiological, and molecular components governing yield under drought and high temperature, but possible by implementing cohesive approaches involving molecular and systems biology approaches in genomics and molecular breeding, including genetic engineering.

OBJECTIVES: To assess the predictive value of serum trypsin and Trypsinogen Activation Peptide (TAP) for the severity of AP by means of a single center cohort study as well as a systematic review of the current literature. METHODS: The literature search was conducted using Medline (PubMed), EMBASE and the Cochrane Central Register. A total of 142 patients with acute pancreatitis (AP) were included in the cohort study and parameters of the revised Atlanta criteria of 2012 and the APACHE II were assessed. RESULTS: The review showed promising results for the predictive value of serum trypsinogen-2, but conflicting results for serum TAP and trypsin. In the cohort study, patients were observed for 4 days after diagnosis of AP: 9 patients had severe AP, 35 patients had moderate AP and 81 patients had mild AP. The ratio of the geometric mean of severe vs mild AP for trypsin was 0.72 (95% CI: 0.51-1.00), p=0.053 and for TAP 0.74 (95% CI: 0.54-1.01), p=0.055 respectively. CONCLUSION: The cohort study showed an inverse correlation of serum levels of TAP and trypsin with severity of AP. Serum TAP and trypsin have an inferior predictive value of severity of AP compared to the clinical APACHE II score.

This work proposes a conceptual design for a process for recovering Polystyrene (PS) using solvents of agro-industrial origin. The literature describes the dilution of Expanded Polyestyrene (EPS) in limonene, followed by its insolubilization with alcohols for recovery. However, there is no information on the solubility limit for the PS + limonene + alcohol system, which is critical for the process design. To determine the solubility limit, we diluted the waste EPS in D-limonene, mixed it with ethanol to form a precipitate, and used a gravimetric method to measure the mass of the compounds. These results allowed for the conceptual design of an EPS recycling process using a chemical process simulator, which includes a separator, a distillation column, and auxiliary equipment such as heaters, coolers, and pumps. An empirical correlation was obtained for the solubility limit, which enabled the design of a process for the treatment of 52 kg/s of PS using 0.75 kg /s of ethanol and 2.4 kg / s of D-limonene once the stationary state had been reached. The distillation column is six-stage, with a reflux ratio of 1.5 and duties of 30 000 kW and -25 847 kW for the condenser and reboiler, respectively.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

Lean practice is recognised for having a great potential in promoting safety risk management in offsite construction (OSC). This paper presents results of a study conducted to assess the impact of lean practice in safety risk management in OSC in a developing country. A quantitative approach using survey-based questionnaire was adopted. Lean management practices (LMPs) identified from literature review were empirically tested using a sample survey of 103 OSC contractors. The survey responses were subjected to descriptive and inferential statistics. The top ranked LMPs for safety risk management in OSC included two mistake proofing practices, i.e., use of personal protective equipment (PPE) and use of hazard warning equipment; two last planner system (LPS) practices, i.e., involvement of workers in safety planning and providing necessary working equipment and one first run studies (FRS) practice, i.e., critical analysis of work methods. These LMPs are useful in controlling high consequence safety risks in OSC. Based on evidence found in this study, the paper argues that lean practice can bring great value in the safety risk management in OSC in countries where OSC is transitioning.

To study the anti-cracking performance of cast-in-place concrete inner shaft lining structure under the combined effects of temperature and constraint, this paper first developed a novel temperature stress test machine suitable for the shape of the inner shaft lining structure and with adjustable endpoint constraint, providing specialized experimental equipment for subsequent cast-in-place concrete inner shaft lining temperature stress simulation experiments. Then, this paper preliminarily studied the temperature, strain, and stress changes of the cast-in-place inner shaft lining under the condition of 100% endpoint constraint by simulating the internal hydration heating and cooling process of the cast-in-place inner shaft lining and using the temperature stress test machine to accurately control the endpoint constraint conditions of the inner shaft lining scaled model.

This paper shares some new information on the ambient temperature profile and the heat stress occurrences directly underneath ground-mounted Solar Photovoltaic (PV) Arrays (monocrystalline-based) focusing on different temperature levels. A common ground for this work lies on the fact that 10C increase of PV cell temperature results in reduction of 0.5% energy conversion efficiency thus any means of natural cooling mechanism would gain much benefit especially to the Solar Farm operators. Transpiration process plays an important role in the cooling of green plants where in average it could dissipate around 32.9% of the total solar energy absorbed by the leaf making it a good natural cooling mechanism. This condition is relatively applied for herbs specifically for this project, Orthosiphon Stamineus or generally known as Java Tea are used as the high value crops. The thermal process via convective heat and mass exchange of leaves with the environment is relevant for a better understanding of plant physiological processes in response to environmental conversion factors for a wide range of applications. An important fact for plant heat stress with respect to the Ambient temperature is that the range lies between 10 C to 15 C above the surrounding value. This heat stress condition is relatively important and should be modelled in crops-energy integration. Agrivoltaic concept is a system that combines commercial agriculture and photovoltaic electricity generation in the same space. The concept is in line with the Kyoto Protocol and the United Nation Sustainable Development Goals (UN-SDG) which highlights the clean energy and sustainable urban living. The integration of agrivoltaic systems would optimize the yield, improving clean system efficiency and solving the issue of land resource sustainability. The PV bottom surface temperature are the main source of dissipated heat as shown in the thermal images recorded at 5 minutes interval at 3 sampling time. Statistical analysis shows that the Thermal correlations for transpiration process and heat stress occurrences between PV bottom surface and plant height will be an important finding for large scale plant cultivation in agrivoltaic farms.

Background: Gluten and casein-containing foods could aggravate the symptoms of children and adolescents with autism spectrum disorder (ASD), and subsequently impact their quality of life. However, there is a mixed opinion among researchers concerning the impact of alternative diet on reducing ASD symptoms. Objective: This scoping review aimed at examining the impact of the ‘’gluten-free, casein-free’’ (GFCF) diet on health outcomes and the quality of life among autistic children and adolescents. Methods: A scoping review of the literature was performed following the Joanna Briggs Institute (JBI) guidelines. Four databases including EbscoHost, Medline, CINAHL and ProQuest were used to obtain subject-specific studies relevant to the research question and published between July 2013 and March 2024. A comprehensive search using keywords such as “autism spectrum disorder”, “gluten-free diet”, and “casein-free diet” was conducted to obtain articles related to the research focus area. Only full-text, peer-reviewed, written in English articles were selected. Data extraction and data analysis were performed according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses- extension to Scoping Review (PRISMA-ScR) protocol. Results: From the initial 586 studies a total of 27 articles were included in the final analysis of the review. The thematic analysis included ‘GFCF diet and improvement of the core autistic symptoms’’, “the gut-brain link’’, ‘’dietary interventions and autism’’, ‘’possible side effects due to the GCFC diet’’, and ‘’ inconclusive studies and mixed opinions’’. Majority of the studies showed positive effect of the GFCF diet on a variety of autistic symptoms including positive changes in cognitive skills, behaviour, and gastrointestinal symptoms while some showed conflicting evidence. Conclusion: The currently available evidence on the impact of ‘GFCF’’ diet on the quality of life of autistic children and adolescents may warrant potentially effective interventions for alleviating symptoms of autism spectrum disorders. However, this scoping review highlighted the need for more research to provide more reliable evidence on the health outcomes and quality of life of ASD sufferers to guide practice.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r&gt;0.90) and peri-urban (HWM, HWA, r&gt;0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Nucleation is a fundamental and general process at the initial stage of first order phase transition. Although various models based on the classical nucleation theory (CNT) have been proposed to explain the energetics and kinetics of nucleation, detailed understanding on nanoscales are still required. Here we focus on homogeneous bubble nucleation, in which evaluation of the size dependence of bubble free energy is the key issue. We propose application of a formula in stochastic thermodynamics, the Jarzynski’s equality, for data analysis of molecular dynamics (MD) simulation to evaluate the free energy of bubble nucleation. As a test case, we performed a series of MD simulations with Lennard-Jones (LJ) fluid system. By applying an external spherical force field to equilibrated LJ liquid, we evaluated the free energy change during bubble growth as the Jarzynski’s ensemble average of required works. A fairly smooth free energy curve was obtained as a function of bubble radius in metastable liquid of mildly negative pressure conditions.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

Cuticular waxes are a mixture of hydrophobic very-long-chain fatty acids and their derivatives accumulated in the plant cuticle. Most studies define the role of cuticular wax largely based on reducing non-stomatal water loss. The present study investigated the role of cuticular wax in reducing both low-temperature and dehydration stress in plants using Arabidopsis thaliana mutants and transgenic genotypes altered in the formation of cuticular wax. cer3-6, a known Arabidopsis wax-deficient mutant (with distinct reduction in aldehydes, n-alkanes, secondary n-alcohols, and ketones compared to wild type (WT)), was most sensitive to water loss; while dewax, a known wax overproducer (greater alkanes and ketones compared to WT), was more resistant to dehydration compared to WT. Furthermore, cold-acclimated cer3-6 froze at warmer temperatures, while cold-acclimated dewax displayed freezing exotherms at colder temperatures compared to WT. GC-MS analysis identified a characteristic decrease in the accumulation of certain waxes (e.g. alkanes, alcohols) in Arabidopsis cuticles under cold acclimation, which was additionally reduced in cer3-6. Conversely, the dewax mutant showed a greater ability to accumulate waxes under cold acclimation. FTIR spectroscopy also supported observations in cuticular wax deposition under cold acclimation. Our data indicate cuticular alkane waxes along with alcohols and fatty acids can facilitate avoidance of both ice formation and leaf water loss under dehydration stress, and are promising genetic targets of interest.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from &lt;5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

Age-related diseases place an intense and growing stress on healthcare systems. Numerous theories of ageing exist. Yet prediction, prevention and treatment limitations of age-related disease persist because we lack a complete aetiological understanding of their origins. Here we propose a new theory that aims to provide a blueprint-type understanding of ageing and disease aetiology, working across multiple scientific disciplines. Supported by specific examples, we demonstrate that the primary driver of much of age-related diseases is the futile triggering of specific molecular pathways in a pathological manner, which we term patho-pathways. Patho-pathways induce pathological cell, tissue and system changes in the form of hyperactivity (undesirable increased and new biological activities that are typical of age related disease). As part of patho-pathways, all wild-type (normal) genes have the potential to contribute to age-related diseases (though specific risk varies and can be formularised). In a domino-style effect, one patho-pathway typically triggers others, resulting in complex, but traceable, cascades. Utility, in terms of changing clinical and scientific practice, is derived from mapping these cascades to create Blueprint Maps that allow identification of biomarkers and therapeutic targets far upstream in the causal chain of events. Finally, our theory provides testable hypotheses concerning predictions of links between otherwise seemingly disparate diseases as well as new interventions into ageing.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of &lt;1 μs, and density of 6.44 g/cm3. In this study, 2-inch diameter β-Ga2O3 single crystals were prepared by oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.

Oxytetracycline (OTC) serves as a widely employed antibiotic in veterinary treatment and prevention of infections, potentially leaving residues in animal-derived food products, such as milk, that are consumed by humans. Given the detrimental effects of prolonged human exposure, it becomes imperative to develop precise and sensitive methods for monitoring the presence of OTC in food. This work reports on the fabrication of a label-free electrochemical aptasensor for the determination of OTC as a proof-of-concept.

Land Surface Temperature (LST) is a basic parameter in energy exchange between the land and atmosphere and is frequently used in many sciences such as climatology, hydrology, agriculture, ecology, etc. LST time series data have usually deficient, missing and unacceptable data caused by the presence of clouds in images, presence of dust in atmosphere and sensor failure. In this study, Singular Spectrum Analysis (SSA) algorithm was used to resolve the problem of missing and outlier data caused by cloud cover. The region studied in the present research included an image frame of MODIS with horizontal number 22 and vertical number 05 (h22v05). This image involved a large part of Iran and Turkmenistan and Caspian Sea. In this study, MODIS LST sensor (MOD11A1) was used during 2015 with 1×1 Km spatial resolution and day/night LST data (daily temporal resolution). The results of the data quality showed that cloud cover caused 36.37% of missing data in the studied time series with 730 day/night LST images. Further, the results of SSA algorithm in reconstruction of LST images indicated the Root Mean Square Error (RMSE) of 2.95 K between the original and reconstructed data in LST time series in the study region. In general, the findings showed that SSA algorithm using spatio-temporal interpolation in LST time series can be effectively used to resolve the problem of missing data caused by cloud cover.

The static formation temperature (SFT) is required to determine the thermophysical properties and production parameters in geothermal and oil reservoirs. However, the SFT is not easy to be obtained by both experimental and physical methods. In this paper, a mathematical approach to predicting SFT based on a new model describing the relationship between bottom hole temperature (BHT) and shut-in time was proposed. The unknown coefficients of the model were derived from least squares fit by Particle Swarm Optimization (PSO) algorithm. Besides, the ability to predict SFT based on a few BHT data (such as first 3, 4, or 5 ones of a data set) was evaluated. The accuracy of the proposed method to predict SFT was testified with a deviation percentage less than ±4% and high values of regression coefficient R² (>0.98). The proposed method could be used as a practical tool to predict SFT in both geothermal and oil wells.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

Recent trends concerning hydrogen as a fuel of the future and problems related to its production, storage and utilization increase the demand for efficient technologies related to these problems. A large part of such technologies is related to application of advanced materials based on various complex oxides which are used as efficient catalysts for fuel transformation into hydrogen and syngas, materials for membranes with selective permeability for hydrogen and syngas production, components of solid oxide fuel cells/electrolyzers as well as many other applications in energy, electrochemistry and catalysis. Such materials are typically based on oxides and solid solutions with perovskite and fluorite structures or their derivatives. Attention is also paid to the materials based on spinel, apatite, mayenite, sheelite, fergusonite structures. The above-mentioned materials are continuously studied in order to modify and optimize their functional properties. On the other hand, other classes of materials (weberites, monazites, etc.) are recently discovered and considered as candidate materials for the aforementioned applications due to their specific functional properties or a great potential of their improvement. In this review, some of these materials are considered.

Though Bangladesh is often labelled as "climate change ground zero," the Chittagong Hill Tracts (CHT) were never considered a significant climate change hotspot until heavy rainfall and consequent landslides in 2017. This shift in problem narrative seemingly overlooks myriad environmentally unsustainable 'development' initiatives along with (il)legal deforestation. This paper examines climate change trends and impacts on the lives and livelihoods of diverse local groups in CHT. By analysing changing patterns in meteorological data and qualitative information on changes and challenges in everyday life and the livelihoods of local people, we show a shortfall of captured climate data on CHT to make a strong case for climate change. Yet, this study finds that this region is exposed to a substantial threat of land degradation, flash floods, water scarcity, landslides, and other slow and quick onsets due to a combined effect of deforestation, neoliberalised development, and slight changes in temperature and precipitation patterns. This paper calls for proactive measures to address climate change impacts by endorsing sustainable development strategies prioritizing environmental stewardship, social justice, and economic prosperity.

The corporate strategic planning of businesses in sub-Saharan Africa (SSA) largely focuses on immediate financial performances with minimal credence to social sustainability. Thus, studies on the linkage between corporate governance and sustainability reporting have focused on developed economies. This study therefore investigated the role of institutional ownership in the impact of board committee characteristics on social sustainability reporting. The study involved strongly balanced panel data with 1,969 observations of 275 publicly listed non-financial firms in SSA within the timeframe of 2012 to 2021. Data was analyzed using STATA 14.1. The hypotheses were tested using the two-step system of the generalized method of moment (GMM) using the Arellano-Bond dynamic panel-data estimation method. The rate of social sustainability reporting was 39.4%. Relatively, Mauritius and South African firms had the most effective board committee characteristics and higher levels of social sustainability reporting. Institutional ownership had no significant effect on social sustainability reporting. Institutional ownership moderated the effect of sustainability committee independence and sustainability committee gender diversity on social sustainability reporting negatively. The paper presents a new perspective on corporate governance and social sustainability literature by examining the effect of institutional ownership on board committee characteristics and social sustainability reporting in SSA.

The COVID-19 pandemic has significantly impacted human health and daily life. Meteorological factors play a crucial role in virus transmission. Understanding these factors is critical for pandemic control, yet debates continue due to variations in research methods and data. This study uses a global dataset and focuses on administrative units smaller than 10,000 km². The relationship between daily COVID-19 incidence rates and meteorological factors—including temperature, relative humidity (RH), ultraviolet radiation (UVR), and diurnal temperature range (DTR)—was analyzed across 173 units in 62 countries. The results revealed significant nonlinear responses and lag effects between incidence rates and the meteorological factors. Key inflection points were observed at 0°C and 24°C for temperature, 63% for RH, 102 KJ/m² for UVR, and 15°C for DTR. Below 0°C, infection risk increased with rising temperatures; from 0°C to 24°C, risk decreased; and above 24°C, risk escalated rapidly. RH below 63% correlated inversely with infection risk, while above 63%, the correlation was positive. Infection risk decreased with UVR below 102 KJ/m² but increased beyond this threshold. These nonlinear responses are primarily driven by the differential effects of these factors on virus survival, transmission, and human immunity. Conditions around 24°C, 63% RH, 102 KJ/m² UVR, and DTR below 15°C appear optimal for human immunity, correlating with lower infection risk. High temperature and low UVR prompted immediate infection responses, while low temperatures, high UVR, and larger DTR showed delayed effects. These findings provide new, more reliable evidence for understanding the mechanisms driving COVID-19 pandemic dynamics and for preventing the future normalization of the epidemic.

Until now, crystalline NiCo2S4 and its composites have demonstrated improve performances in supercapacitor applications, compared to their oxide analogous, due to their relatively higher electrical conductivity, and multifaceted redox reaction. However, amorphous phase materials have recently shown promise in electrochemical energy storage systems. In this work, urea-assisted amorphous NiCo2S4 on nickel foam (referred to as aNCS) with high nitrogen atom% content, was obtained via hydrothermal method. In comparison to the crystalline NiCo2S4 (referred to as cNCS), aNCS exhibited superior electrochemical performance with specific capacitance of ~3506 F g-1 which is higher than cNCS specific capacitance of ~2185 F g-1 at 2 A g-1. Additionally, aNCS in two-electrode asymmetry supercapacitor exhibited specific capacitance and energy density of ~196 F g-1 and 56 Wh kg-1, respectively.

Autonomous navigation in dynamic environments poses a significant challenge in the field of ro-botics with the primary goals of ensuring both smooth and safe movement. This study introduces control strategy based on an Adaptive Neuro-Fuzzy Inference System (ANFIS) to enhance au-tonomous robot navigation in dynamic environments, emphasizing on collision-free path plan-ning. This strategy employs, a path planning technique to develop a trajectory that allows the ro-bot to navigate smoothly while avoiding collisions with both static and dynamic obstacles. The developed control system incorporates four ANFIS controllers: two are tasked with guiding the robot toward its end point, and the other two are activated for obstacle avoidance. The experi-mental setup conducted in CoppeliaSim involves a mobile robot equipped with ultrasonic sensors navigating in an environment with static and dynamic obstacles. Simulation experiments are conducted to demonstrate the model's capability in ensuring collision-free navigation, employing a path planning algorithm to ascertain the shortest route to the target destination. The simulation results highlight the superiority of the ANFIS-based approach over conventional methods, partic-ularly in terms of computational efficiency and navigational smoothness.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

There have been exciting advances in our knowledge of primary glomerular diseases and nephrotic syndromes in recent years. Beyond the histological pattern from renal biopsy, more precise phenotyping of the diseases and the use of modern nephrogenetic helps to improve treatment decisions and sometimes also to avoid unnecessary exposure to potentially toxic immunosuppression. New Biomarkers led to easier and more accurate diagnoses and more targeted therapeutic decisions. The treatment landscape is getting wider with a pipeline of promising new therapeutic agents with more sophisticated approaches. This review focuses on all aspects of entities that are associated with nephrotic syndromes with updated information on recent advances in each field. This includes podocytopathies (Focal Segmental Glomerulosclerosis and Minimal-Change Disease), Membranous Nephropathy, Membranoproliferative Glomerulonephritis, IgA-Nephropathy, Fibrillary Glomerulonephritis, Amyloidosis and monoclonal gammopathy of renal significance in the context of the nephrotic syndrome, but also renal involvement in systemic diseases, diabetic nephropathy, and drugs that are associated with nephrotic syndromes.

Background/Aim: Stool gluten immunogenic peptides (GIP) determination is now considered a valuable tool for detecting dietary lapses in treated celiac disease (CeD) patients. Our study aims to explore the diagnostic performance of a qualitative lateral flow immunoassay point-of-care test (LFIA/PoCT) compared with a qualitative enzyme-linked immunosorbent assay (ELISA) for detection of stool GIP. Methods: The study is a post hoc analysis of stool samples collected in the real-life conditions from a cohort of gluten-free diet-treated CeD patients. Stool GIP was measured in µg/g of stool using an ELISA kit (iVYLISA GIP S®, Biomedal SL). For the qualitative evaluation of stool GIP, a LFIA/PoCT test (GlutenDetect®; Biomedal S.L) was employed, which reported results as positive or negative. The LFIA/PoCT performance was evaluated against ELISA, considered as the gold standard. GIP concentrations

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

The Asiatic apple leafminer, Phyllonorycter ringoniella (Matsumura), is a significant secondary pest of apple trees in Northeast Asia. To better understand its population dynamics, a population model based on temperature-developmental relationships was constructed. This model includes three sub-models: spring emergence, immature stage transition, and adult oviposition. Field data were collected from sex-pheromone baited traps in apple orchards in Andong, Korea, dur-ing 2015 and 2016 to validate the model. Simulations under six pesticide-natural enemy scenari-os showed that the population size of each generation was best simulated when weighted mor-tality factors for pesticides and natural enemies were applied. Using daily temperature inputs, the model demonstrated that P. ringoniella typically undergoes five generations per year, with peak times predicted within a seven-day margin of field data. Sensitivity analyses revealed that population size was influenced by total fecundity and the larval stage model, but peak times remained consistent despite parameter changes. Higher temperatures led to earlier adult peak dates, especially in summer generations. This model serves as a fundamental tool for estimating population dynamics and abundance changes of P. ringoniella and can guide the timings of pesti-cide application. Further validation is necessary to test the model's efficacy in controlling pests in apple orchards.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Worldwide the severity of abiotic stress like heat, drought, salinity, cold, waterlogging, etc. are being increased because of global warming. Wheat crops must adapt to harsh environments through physiological, molecular, and genetic manipulation. Because of abiotic stress, reactive oxygen species (ROS) and reactive nitrogen species (RNS) produced in wheat plants break down DNA and RNA bases, protein, lipid, and other macro- and micromolecules, resulting in stunted growth and yield decline. Abiotic stress also induces the crop's molecular functions, physiological, biological, and cellular processes, and their compositions. Different stressors like high light intensity, heat, drought, and salinity also impair photosynthesis damaging various pigments. Antioxidant enzymes, such as catalase (CAT), superoxide dismutase (SOD), peroxidase (POD), and ascorbate peroxidase (APX), etc. synthesized in harsh environments can ameliorate ROS/RNS produced in oxidative stress. Under abiotic stress, heat shock proteins (HSPs) heat shock transcription factors (HSFs) in heat stress, and dehydration-responsive element binding proteins (DREBs) in drought stress are activated to synthesize proteins to mitigate the deleterious effects of those stressors. Na⁺ exclusive genes (NAX1, NAX2) and Na⁺/H⁺ (K⁺) antiporter genes (NHX1, NHX2) hinder those ions from uptake into leaf sheaths and blades of wheat resulting in the declination of salinity in plants. Exogenous hormones like gibberellic acid, salicylic acid, and melatonin, etc., and osmoprotectants like proline, and gene manipulation in plants through genetic engineering are being employed to mitigate the toxic effects of abiotic stress on plants, as portrayed in many literatures. The review depicts how abiotic stress affects phenotypic, physiological, and molecular structures and functions of wheat crops, and their mitigation strategies to lessen their noxious effects on wheat.

This study presents a comprehensive approach to calculating the free energy of hydration of methane using Molecular Dynamics simulations. We employed the Free Energy Perturbation (FEP) method to determine the Gibbs free energy associated with transferring a methane molecule into water. Simulations were conducted in a cubic simulation box containing one methane molecule and 1000 TIP4P water molecules. The forward and backward routes were both analyzed, providing consistent free energy differences, which validates the robustness of our methodology. The Gibbs free energy profiles demonstrated characteristic energy barriers and stabilization points, indicative of the interaction dynamics in the solvation process. The results demonstrate the robustness of the FEP method implemented in LAMMPS, yielding free energy in close agreement with experimental data and previous computational studies. The calculated free energy differences for methane hydration exhibited deviations of 13% and 8% for the forward and backward routes, respectively, compared to experimental values. These findings underscore the accuracy and efficiency of using LAMMPS for free energy calculations, contributing to the broader understanding of solvation thermodynamics. Additionally, radial distribution functions were analyzed to provide insights into the structural arrangement of water molecules around methane, revealing strong interaction between methane's carbon atom and water molecules.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Drought negatively affects the growth and development of barley. To explore the genetic variation in barley under drought stress, ten breeding genotypes were tested using polyethylene glycol-6000 to simulate drought conditions. We observed that drought stress adversely affected germination-related traits across all barley genotypes and this impact varied between genotypes, suggesting genotype-specific drought tolerance. The drought tolerance index was an ideal criterion for selecting drought-tolerant genotypes as it well characterized the gradient responses of barely genotypes to drought stress. Based on this indicator, genotype OB1878-ON-50 is recommended as a significant germplasm resource for breeding programs under lower precipitation conditions due to its superior tolerance to drought stress.

This literature review provides an in-depth exploration of the research conducted on the investigation and measurement of residual stress (RS) in Wire Arc Additive Manufacturing (WAAM) products, particularly focusing on how process parameters influence the phenomenon. RS plays a crucial role in determining the mechanical behavior and structural integrity of WAAM components. This review article gives an understanding of the relationship between process parameters and RS to optimize the WAAM processes and ensure the durability of the final products. It also summarizes key findings, measurement techniques, challenges, and future directions in this evolving field. The review also analyzes a measurement of RS in the products of WAAM as a function of process parameters depending on examining various research studies, techniques, and methodologies employed in their studies. Experimental measuring techniques and numerical analysis of RS to determine the impacts of RS in mechanical response in products of WAAM were discussed. By offering a comprehensive overview of current research trends and insights, this review serves as a valuable resource to guide future investigations, fostering the advancement of WAAM as a robust and efficient manufacturing technology.

Multifunctional coatings based on Sn-Ni materials with and without titanium oxide nanoparticles (TiO2NPs) incorporation were prepared using the electrochemical deposition technique at 70°C. TiO2NPs were dispersed in the electrolyte bath, and their influence on both surface texture, crystalline phase, and properties was investigated. Various techniques such as X-ray phase analysis (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray microanalysis (EDX) were used to characterize the prepared coatings. The anti-corrosion effectiveness of the coatings was assessed using potentiodynamic polarization curves and electrochemical impedance spectroscopy in an artificial sweat medium, while the bactericidal activity of the composite coatings (the ability to induce cell death) was evaluated in accordance with ISO 27447:2009 test. The influence of the TiO2NPs on the composition, structure and properties of the deposited coatings was established. Particular attention was paid to the relationship between the anticorrosive and bactericidal properties of the coatings and their structure and composition. The synergistic effect of the various properties was investigated and discussed.

Vanilla planifolia is grown as a high-value orchid spice for its odor and savor attributes that increase due to the curing process associated with microbial colonization. This tends to influence the aromatic properties of vanilla. Hence, 11 Bacillus sp. strains were isolated from V. planifolia and identified with 16S rRNA gene sequencing. The liquid culture (1 mL of 107 CFU mL-1) of selected Bacillus vallismortis NR_104873.1:11-1518, B. velezensis ZN-S10, and B. tropicus KhEp-2 effectively fermented green-blanched vanilla pods kept at 10 ℃ during the sweating stage. GC-MS analysis showed that the methanol extract of non-coated, and B. vallismortis treated vanilla detected three (3) volatile compounds, whereas seven (7) components were obtained in B. tropicus and B. velezensis treatment. 4H-pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl was found in B. velezensis ZN-S10, B. tropicus KhEp-2, B. vallismortis while it was not present in the control samples. This ketone compound suggested a Maillard reaction resulting in brown-increased aroma pods. Linoleic acid and Hexadecanoic acid ethyl esters were detected only in ZN-S10 strain-coated vanilla. A novel 3--Deoxy-d-mannoic lactone was detected only in B. vallismortis treated vanilla characterized as a new compound in V. planifolia which suggested that the new compound can be altered with the coating of bacteria in vanilla during fermentation. Thus, the Bacillus strains improved the volatile profile and exhibited a new aroma and flavor profile of vanilla owing to bacteria fermentation during the curing process.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Reduced glutathione (GSH) is an antioxidant in plants and is one of the important ways for plants to combat low-temperature stress. In this paper, Eriobotrya japonica Lindl. cv. Zaozhong No. 6 seedlings were used to study the effects of exogenous 5-aminolevulinic acid (ALA) application on glutathione synthesis and cyclic metabolism of loquat seedlings under low-temperature stress and to explore the regulatory mechanism of ALA on loquat cold tolerance. The results showed that ALA treatment could increase the content of GSH and the reduced glutathione/oxidized glutathione (GSH/GSSG) ratio in loquat leaf slices under low-temperature stress; reduce the electrolyte leakage rate and GSSG, H₂O₂ and MDA contents in leaf tissues; and alleviate the peroxidation damage caused by low temperature. ALA treatment increased the activity of γ-glutamine synthetase (γ-ECS) in loquat leaf slices under low-temperature stress and promoted the biosynthesis of reduced glutathione, thereby increasing the GSH content in leaf tissues. On the other hand, ALA treatment could also improve the activities of glutathione reductase (GR), glutathione S-transferase (GST) and glutathione peroxidase (GPX) and promote the cyclic regeneration of GSH, accordingly maintaining a high GSH/GSSG ratio, promoting the removal of reactive oxygen species (ROS), and enhancing the antioxidant capacity of leaves. The regulatory effect of ALA on enhancing the antioxidant capacity of loquat seedlings under low-temperature stress can be inhibited by L-buthionine-sulfoximine (BSO, GSH biosynthesis inhibitor). The results showed that ALA improved the antioxidant capacity of loquat seedlings under low-temperature stress, and GSH was involved in the regulation of the antioxidant effect of ALA on loquat seedlings under low-temperature stress.

This review aims to explore the intricate relationship between epigenetic mechanisms, stress, and affective disorders, focusing on how early life experiences and coping mechanisms contribute to susceptibility to mood disorders. Epigenetic factors play a crucial role in regulating gene expression without altering the DNA (deoxyribonucleic acid) sequence, and recent research has revealed associations between epigenetic changes and maladaptive responses to stress or psychiatric disorders. A scoping review of 33 studies employing the PRISMA-S (Preferred Reporting Items for Systematic Reviews and Meta-Analyses – Statement) guidelines investigates the role of stress-induced epigenetic mechanisms and coping strategies in affective disorders' occurrence, development, and progression. The analysis encompasses various stress factors, including childhood trauma, work-related stress, and dietary deficiencies, alongside epigenetic changes such as DNA methylation and altered gene expression. Findings indicate that specific stress-related genes frequently exhibit epigenetic changes associated with affective disorders. Moreover, the review examines coping mechanisms in patients with bipolar disorder and major depressive disorder, revealing mixed associations between coping strategies and symptom severity. While active coping is correlated with better outcomes, emotion-focused coping may exacerbate depressive or manic episodes. Overall, this review underscores the complex interplay between genetic predisposition, environmental stressors, coping mechanisms, and affective disorders. Understanding these interactions is essential for developing targeted interventions and personalized treatment strategies for individuals with mood disorders. However, further research is needed to elucidate specific genomic loci involved in affective disorders and the clinical implications of coping strategies in therapeutic settings.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

The arsRBC operon encodes a 3-protein arsenic resistance system. ArsR regulates the transcription of the operon, while ArsB and ArsC are involved in exporting trivalent arsenic and reducing pentavalent arsenic respectively. Previous research in Agrobacterium tumefaciens 5A demonstrated ArsR has regulatory control over a wide range of metal related proteins and metabolic pathways. We hypothesized that ArsR has broad regulatory control in other Gram-negative bacteria and set out to test this. Here, we use differential proteomics to investigate changes caused by the presence of the arsR gene in human microbiome-relevant Escherichia coli during arsenite (AsIII) exposure. We show that ArsR has broad-ranging impacts such as the expression of TCA cycle enzymes during AsIII stress. Additionally, we found that the Isc [Fe-S] cluster and molybdenum cofactor assembly proteins are upregulated regardless of the presence of ArsR under these same conditions. An important finding from this differential proteomics analysis was the identification of response mechanisms that were strain, ArsR, and arsenic specific, providing new clarity to this complex regulon. Given the widespread occurrence of the arsRBC operon, these findings should have broad applicability across microbial genera, including sensitive environments such as the human gastrointestinal tract.

The success of deep learning (DL) in offline brain-computer interfaces (BCIs) has not yet translated into efficient online applications. This is due to three primary challenges. First, most DL solutions are designed for offline decoding, making the transition to online decoding complex and unclear. Second, the use of sliding windows in online decoding increases the computational complexity of DL training. Third, DL models typically require large amounts of training data, which are often scarce in BCI applications. To address these issues and enable real-time decoding, even across different subjects without calibration data, we first introduce a novel approach called real-time adaptive pooling (RAP). RAP modifies the pooling layers of existing offline DL models towards the online decoding requirements. Additionally, it significantly reduces the computational demand during training by jointly decoding consecutive windows. To reduce the amount of training data required, our approach leverages different levels of domain adaptation. We show how different settings enable different adaptation solutions. The results demonstrate that our approach is both powerful and can be calibration-free, providing a robust and practical solution for real-time BCI applications. These findings pave the way for the development of co-adaptive and highly efficient DL-based online BCI systems.

Stress is a natural yet potentially harmful aspect of human life, necessitating effective management, particularly during overwhelming experiences. This paper presents a scoping review of personalized stress detection models using wearable technology. Employing the PRISMA-ScR framework for rigorous methodological structuring, we systematically analyzed literature from key databases including Scopus, IEEE Xplore, and PubMed. Our focus was on biosignals, AI methodologies, datasets, wearable devices, and real-world implementation challenges. The review presents an overview of stress and its biological mechanisms, details the methodology for the literature search, and synthesizes the findings. It shows that biosignals, especially EDA and PPG, are frequently utilized for stress detection and demonstrate potential reliability in multimodal settings. Evidence for a trend towards deep learning models was found, although the limited comparison with traditional methods calls for further research. Concerns arise regarding the representativeness of datasets and practical challenges in deploying wearable technologies, which include issues related to data quality and privacy. Future research should aim to develop comprehensive datasets and explore AI techniques that are not only accurate but also computationally efficient and user-centric, thereby closing the gap between theoretical models and practical applications to improve the effectiveness of stress detection systems in real scenarios.

According to previous studies the median raphe region (MRR) is known to contribute significantly to social behavior. Beside serotonin, there are reports of a small population of dopaminergic neu-rons in this region. Dopamine is linked to reward and locomotion, but very little has been known about its role in the MRR. To address that, we first confirmed the presence of dopaminergic cells in the MRR of mice (immunohistochemistry, RT-PCR) and humans (RT-PCR). Next, we used chemogenetic technology in mice containing Cre enzyme under the promoter of the dopamine transporter (DAT). With the help of an adeno-associated virus, artificial receptors were expressed in the dopaminergic cells of the MRR (DAT-MRR). Four weeks later, extensive behavioral charac-terization started 30 minutes after the injection of the artificial ligand (Clozapine-N-Oxide). Stimu-lation of DAT-MRR decreased social interest without influencing aggression and with an increase in social discrimination. Additionally, inhibition of the same cells increased the friendly social be-havior during social interaction test. No behavioral changes were detected in anxiety, memory and locomotion. All in all, dopaminergic cells were present both in the mice and human MRR, and manipulation of dopaminergic neurons of the MRR elicited a specific social response.

Maintaining the optimal microclimate in broiler houses is crucial for bird productivity, yet enabling efficient temperature control remains a significant challenge. This study developed and validated a computational fluid dynamics (CFD) model to predict temporal changes in indoor air temperature in response to variable ventilation operations in a commercial broiler house. The model accurately simulated air velocity and airflow distribution for different numbers of tunnel fans in operation, with air-velocity errors ranging from -0.22 to 0.32 m s-1. The predicted airflow rates through inlets and cooling pads showed good agreement with measured values with an accuracy of up to 108.1%. Additionally, the CFD model effectively predicted temperature dynamics, accounting for chicken heat production and ventilation effect. The model successfully predicted the longitudinal temperature gradients and their variations during ventilation cycles, validating its reliability through comparison with experimental data. The study also explored different variable inlet configurations to mitigate the temperature gradient. The variable inlet adjustment showed the potential to relieve the high temperatures but may reduce overall ventilation efficiency or intensify temperature gradients, which confirms the importance of optimising ventilation strategies. This CFD model provides a valuable tool for evaluating and improving ventilation systems and contributes to enhanced indoor microclimates and productivity in poultry houses.

Microsporidia are intracellular parasites infecting a wide range of vertebrates and invertebrates. In bees, they cause a diarrheal disease called nosematosis, which represents a growing problem contributing to the decline of bee colonies. This parasitic disease infects the gastrointestinal tract of bees, disrupts their immune system, weakens them, and shortens their lifespan. There are two known species of this microsporidial parasite with a global distribution: Vairimorpha apis and Vairimorpha ceranae, with current research indicating that the species V. ceranae is gradually replacing V. apis. In this study, we focused on the detection and occurrence of Vairimorpha spp. in bee colonies kept in different environments, as well as on comparing the impact of hive location on its occurrence. The methods used included sampling from winter bee carcasses, microscopic examination of bee gut contents, and subsequent molecular duplex PCR analysis. Altogether, we examined 82 hives located at 4 different sites and focused on the impact of transportation as an abiotic factor disturbing bees leading to the development of Vairimorpha spp. disease. The results indicate an increased occurrence of this parasite in hives located in urban sites and hives situated in intravillage locations, which may be attributed to transportation and associated vibrations as an abiotic stress factor. Detection revealed that all samples were positive for Vairimorpha ceranae.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Transfer RNA (tRNA) modifications are essential for the temperature adaptation of thermophilic and psychrophilic organisms, as they control the rigidity and flexibility of transcripts. To further understand how specific tRNA modifications are adjusted to maintain functionality in response to temperature fluctuations, we investigated whether tRNA modifications represent an adaptation of bacteria to different growth temperatures (minimal, optimal, and maximal), focusing on closely related psychrophilic (P. halocryophilus and E. sibiricum), mesophilic (B. subtilis), and thermophilic (G. stearothermophilus) Bacillales. Utilizing an RNA sequencing approach combined with chemical pre-treatment of tRNA samples, we systematically profiled dihydrouridine (D), 4-thiouridine (s4U), 7-methyl-guanosine (m7G), and pseudouridine (Ψ) modifications at single-nucleotide resolution. Despite their close relation, each bacterium exhibited a unique tRNA modification profile. Our findings revealed increased tRNA modifications in the thermophilic bacteria at higher temperatures, particularly showing elevated levels of s4U8 and Ψ55 modifications compared to non-thermophilic bacteria, indicating a temperature-dependent regulation that may contribute to thermotolerance. Furthermore, we observed higher levels of D modifications in psychrophilic and mesophilic bacteria indicating an adaptive strategy for cold environments by enhancing local flexibility in tRNAs. Our method demonstrated high effectiveness in identifying tRNA modifications compared to an established tool, highlighting its potential for precise tRNA profiling studies.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

Faba bean is grown globally for human consumption and animal feed and is a significant rotation crop in cereal dominant areas in many countries including Australia. It is sensitive to several abiotic stresses, such as drought, frost and high temperatures, especially at the reproductive stage. However, little is known of the upper and lower temperature limits for successful podding. Experiments were conducted over two years at Breeza and Narrabri in north-western New South Wales to assess the impact of temperature on flowering and pod set of three genotypes; Doza, Cairo and IX1148f under field conditions. Flowering nodes were tagged from designated plants in the field and scored for podding, field temperatures were recorded. Optimum maximum temperature for podset ranged from 23.7-26.1 °C and the equivalent minimum temperature was 3.2-3.8 °C. Optimum average daily temperature for podset ranged from 12.7-13.9 °C. The strongest correlations between temperature and podding were observed at minimum temperatures, indicating that low temperatures are more important than high temperatures in determining yield in faba bean.

Type-1 Diabetes Mellitus (T1D) onset and development is closely linked with imbalance of gut microbiome, while supplementation with probiotics may result in positive alterations in gut microbiome composition. In the present study, the effect of a dietary intervention including free or immobilized cells of the presumptive probiotic Pediococcus acidilactici ORE5 on Corinthian currants, a food with beneficial impact in the condition of diabetes, was investigated. Male Wistar rats were studied which were divided into 4 groups: healthy animals, which received the free (H_FP) or the immobilized cells (H_IPC), and diabetic animals, which received the free (D_FP) or the immobilized cells (D_IPC), for 4 weeks (109 cfu/day, in all groups). At the end of the dietary intervention, D_IPC group exerted lower concentration of the inflammatory cytokine IL-1b compared to D_FP. Consumption of immobilized on Corinthian currants P. acidilactici ORE5 cells by diabetic animals led to increased loads of fecal lactobacilli and lower levels of Enterobacteriaceae, coliforms, and E. coli, while Actinobacteria phylum, Akkermansia, and Bifidobacterium genera abundances were increased, and fecal lactic acid was elevated. Overall, the results of the present research demonstrated that functional ingredients can ameliorate gut dysbiosis present in T1D and could be used to design dietary patterns aiming at T1D management. However, well-designed clinical trials are necessary, in order to confirm the beneficial effects in humans.

This study investigates stress perceptions, somatization, and coping strategies among 271 nursing and dentistry (n=126 and n=145, respectively), undergraduate and postgraduate students. For the study, an e-questionnaire was designed in a two-step process, uploaded in Google Forms and staying open for submissions during February 2024 in the School of Health Sciences, National and Kapodistrian University of Athens. In our sample, predominantly female (68.60%), the majority were undergraduates (80.10%). Females reported higher stress somatization (M=10.22, SD=5.23) compared to males (M=7.94, SD=6.14), with a moderate effect size (Cohen’s d=0.412, p

The problems of modeling the human bladder and its stress-strain state under external static influence were considered. A method for identification of the anisotropic biomechanical characteristics of bladder tissue was proposed. A FEM model was created, which accepts into regard that the bladder is surrounded by fiber and affected by surrounding organs, and partially protected by pelvic bones. The model considered the presence of constant hydrostatic pressure on the walls of the bladder when it is full. It has been shown that isotropic mechanical characteristics of biological tissue can be used for studying the deformed state of a filled bladder if the filled bladder 300 ml is considered as initial non-deformed stage. This was shown by modeling and verification the effect of the external static force on the bladder. Numerical experiments were conducted based on the constructed model. To validate the results obtained, a series of natural experiments on the effect of external pressure on the bladder under ultrasound control was conducted. In the future, it is planned to use the constructed model to study rupture deformations of the bladder under the influence of static and dynamic loads.

Structural and functional materials are subjected to harsh oxidizing environments that lead to a rapid decline in their surface chemical stability. At high-temperatures, the diffusion of atoms is erratic; thus, the reactive elements (REs) get a chance to migrate to the surface and look for oxygen-reactive sites. Their migration from the lattice sites creates vacancies in the matrix and thus weakens the bond, making the material prone to environmental degrading factors. Subsequently, the inward diffusion of oxygen, sulfur, nitrogen, or carbon may occupy these vacancies, resulting in undesired precipitation at the grain boundary, which is usually brittle. The solubility and dissociation of attacking species and corrosion products play the most critical role in corrosion in high-temperature water. To evade such situations, Ti, Al, and Cr are added in Ni/Fe-based alloys, forming a dense oxide layer on the surface that impedes further surface migration of ions. The stability of the alloys is then determined by the capability of these oxide layers to heal or reform during spalling/cracking. This review attempts to understand the migration of REs at the interfaces to prepare structural materials in any unexpected set of oxidizing service conditions. This review will also try to establish the interaction mechanism of REs novel/conventionally added in the alloys with the oxidizing elements in the environments to design better degradation-resistant high-temperature alloys.

The infrared (IR) satellite remote sensing of sea surface skin temperature (SSTskin) is challenging in the northern high latitude region, especially in the Arctic because of its extreme environmental conditions, and thus the accuracy of SSTskin retrievals is questionable. Several Saildrone uncrewed surface vehicles were deployed at the Pacific side of the Arctic in 2019, and two of them, SD-1036 and SD-1037, were equipped with a pair of IR pyrometers on the deck whose measurements have been shown to be useful in the derivation of SSTskin with sufficient accuracy for scientific applications, providing an opportunity to validate satellite SSTskin retrievals. This study aims to assess the accuracy of MODIS-retrieved SSTskin from both Aqua and Terra satellites by comparisons with collocated Saildrone-derived SSTskin data. The mean differences in SSTskin from the SD-1036 and SD-1037 measurements are different by ~0.4 K, largely resulting from differences in the atmospheric conditions experienced by the two Saildrones. The performance of MODIS on Aqua and Terra in retrieving SSTskin is comparable. Negative brightness temperature (BT) differences between 11 μm and 12 μm channels are identified as being physically based, but are removed from the analyses as they present anomalous conditions for which the atmospheric correction algorithm is not suited. Overall, the MODIS SSTskin retrievals show negative mean biases, -0.234 K for Aqua and -0.295 K for Terra. The variations in the retrieval inaccuracies show an association with diurnal warming events in the upper ocean from long periods of sunlight in the Arctic. Also contributing to inaccuracies in the retrieval is the surface emissivity effect in BT differences characterized by the Emissivity-introduced BT difference (EΔBT) index. This study demonstrates the characteristics of MODIS-retrieved SSTskin in the Arctic, at least at the Pacific side, and underscores that more in situ SSTskin data at high latitudes are needed for further error identification and algorithm development of IR SSTskin.

The utilization of optical antennas for active control of far-field radiation at the subwavelength scale is crucial in various scientific and technological applications. We propose a thermally tunable disk design of indium tin oxide (ITO) and aluminum gallium nitride (Al0.18Ga0.82As), enabling a switch between absorption and scattering. Furthermore, the control of far-field radiation pattern can be easily realized by combining ITO and Al0.18Ga0.82As to enhance or suppress emission. Our results demonstrate that hybrid structure can be dynamically tuned with temperature variations. In the proposed design, a frequency is achieved at the epsilon-near-zero wavelength of 1240 nm. The thermal tunability of hybrid structure introduces new multifunctional possibilities for light manipulation, thereby enhancing the potential applications of new devices in the near-infrared range.

The ability of thermoresponsive polymers to respond to temperature with a reversible conformational change makes them promising ‘smart’ materials for solutions in medical and biotechnological applications. In this work, two such polymers and structural isomers were studied: poly(N-isopropyl acrylamide) (PNiPAm) and poly(2-isopropyl-2-oxazoline) (PiPOx). We compare the critical solution temperatures (CST) of these polymers in D2O and H2O in the presence of Hofmeister series salts, as results obtained under these different solvent conditions are often compared. D2O has a higher dipole moment and electronegativity than H2O, which could significantly alter the CST transition. We used two complementary methods to measure the CST, dynamic light scattering (DLS) and differential scanning calorimetry (DSC), and found that the CST decreased significantly in D2O compared to H2O. In the presence of highly concentrated kosmotropes, the CST of both polymers decreased in both solvents. The influence of the kosmotropic anions was smaller than the water isotope effect at low ionic strengths but considerably higher at physiological ionic strengths. However, the Hofmeister anion effect was quantitatively different in H2O than in D2O, with the largest relative differences observed for Cl-, where the CSTs in D2O decreased more than in H2O measured by DLS but less by DSC. PiPOx was more sensitive than PNiPAm to the presence of chaotropes. It exhibited much higher transition enthalpies and multistep transitions, especially in aqueous solutions. Our results highlight that measurements of thermoresponsive polymer properties in D2O cannot be compared directly or quantitatively to application conditions or even measurements performed in H2O.

Heavy rains result in significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended periods of intense precipitation. Accurate rainfall prediction is crucial in nations such as Bangladesh, where agriculture is the predominant field of occupation. The efficiency of machine learning methods is enhanced by the nonlinearity of rainfall, surpassing the effectiveness of other approaches. This study proposes the novel combination of rainfall occurrence prediction, rainfall amount prediction, and daily average temperature prediction. This research implements machine learning techniques and an ensemble-based classifier to predict rainfall occurrence, as well as machine learning regressor models and an ensemble-based regressor to predict the rainfall amount and daily average temperature, using the Bangladesh Weather Dataset. The ensemble classifier demonstrated an accuracy of 83.41% and a recall of 78.17%, exhibiting the best performance in predicting when it will rain, but its precision was the lowest, at 51.16%. The ensemble regression model outperformed the base models, including linear regression, random forest, and support vector regression in rainfall amount prediction, with the lowest mean absolute error of 0.36 and root mean squared error of 0.90. Additionally, this model provided the most precise daily average temperature prediction results with the lowest mean absolute error of 0.42 and root mean squared error of 0.54, highlighting its superiority over the other regression models in forecasting temperature. Ensemble approaches consistently exhibit superior task performance metrics.

The amino acid proline accumulates in plants during abiotic stresses such as drought and salinity and is considered a reliable marker of environmental stress. While its accumulation is well established, its precise role in stress tolerance and its underlying molecular mechanism remain less clear. To address these issues, we performed a meta-analysis - a robust statistical technique that synthesizes results from multiple independent studies while accounting for experimental differences. We focused on 16 physiological and morphological parameters affected by drought and salt stress in transgenic plants expressing proline metabolic genes. For each parameter, we calculated the effect size as the response ratio (RR), which represents the logarithm of the mean value in the transgenic group over the mean value of the control group (lnRR). Under stress, most parameters exhibited significantly higher response ratios in the transgenic group, confirming the beneficial effects of proline during drought and salt stress. Surprisingly, under non-stressed conditions, most stress markers showed no significant differences between transgenic and non-transgenic plants, despite elevated proline levels in the former. These results suggest that the benefits of proline may be related to proline catabolism or may only become apparent during stress, possibly due to interactions with reactive oxygen species (ROS), which accumulate predominantly under stress conditions.

Students studying dentistry and nursing experience anxiety daily, which affects both their general well-being and academic achievement. Anxiety is exacerbated by several circumstances, such as stressors in one's personal life, clinical environment exposure, and academic expectations. To effectively regulate anxiety and support students' achievement, treatments that take these elements into account must be designed. In this study, 271 students from the National and Kapodistrian University of Athens, Greece's departments of dentistry and nursing were polled. Being the following resources, participants filled out an electronic questionnaire that was uploaded to Google Forms and assessed their levels of stress, anxiety, depression, resilience, hope, and spiritual well-being: a) the Depression, Anxiety, Stress Scale (DASS-21), b) the Functional Assessment of Chronic Illness Therapy-Spiritual Well-Being Scale (FACIT-12), c) the Adult Hope Scale (AHS), d) the Resilience Assessment Questionnaire (RAQ8), and e) the Brief Resilience Scale (BRS). Additionally, demographic data was gathered, such as gender, educational attainment, family income, and country of origin. Statistical analyses were performed to investigate the relationships between the variables, including hierarchical multiple linear regression and t-tests. The sample consisted of 271 students from the Department of Nursing (n=126, 46.5%) and Dentistry (n=145, 53.5%), with 68.60% of them being female, 80.10% being undergraduate students, and 48.30% being from Athens, the country's capital. Comparatively speaking, 74.50 percent of nursing students were female, while 62.80% of dental students were. Compared to dental students (2.10%), nurses (40.50%) participated in postgraduate studies at a higher rate. Compared to dental students (44.80%), nursing students reported a household income of just 13.90%, which is much less than €35,000. Anxiety was reported by 51.30% of participants overall, with dental students reporting higher anxiety than nursing students. Higher family wealth was associated with reduced stress levels, while female undergraduate students reported higher levels of anxiety than their male counterparts. Hope was a strong predictor of resilience, but stress and worry had a negative correlation. Promoting students' well-being and academic success requires effective stress-reduction and resilience-building techniques aimed to not only improve student performance but also support future healthcare professionals' personal sustainability and holistic growth.

Chronic stress, culminating in burnout, evolves gradually and is notoriously difficult to detect due to vague symptoms and individuals' hesitance to acknowledge their struggles. To expedite the identification and recognition of this condition, enabling timely psychological intervention, the integration of Artificial Intelligence (AI) is increasingly considered. This research does not assert the feasibility of an AI system managing all aspects of chronic stress's impact. However, it highlights the capability of current technology to detect stress indicators based on quantifiable data like Heart Rate (HR) and organizational climate dimensions. Although other physiological markers such as oximetry, skin galvanic response, and EKG have been explored, they have not shown reliable differentiation between stress and joy. Focused on the unique context of school principals in the Bedouin regions of Israel, this study investigates the interplay between HR, organizational climate, and stress levels. It introduces a novel application of a fuzzy logic tool that combines HR and organizational climate metrics to aid in stress diagnosis. This tool incorporates the psychologist's expertise to provide real-time data crucial for developing effective coping strategies. While the AI-supported fuzzy system does not replace professional psychological intervention, it significantly enhances the speed of condition identification and intervention planning, thus shortening the response time to stress-related issues in educational leadership within culturally specific settings. The application of such AI-driven tools is pivotal for sustaining the well-being and effectiveness of educational leaders, thereby supporting the broader goal of educational sustainability.

The efficient preparation of single-stranded DNA (ssDNA) rings, as a macromolecular construction approach with topological features, has aroused much interest due to their numerous applications in biotechnology and DNA nanotechnology. However, an extra splint is essential for enzymatic circularization, and by-products of multimers are usually present at high concentrations. Here, we proposed a simple and robust strategy of using permuted precursor (linear ssDNA) for circularization by forming an intramolecular dynamic nick using a part of the linear ssDNA substrate itself as the template. After the simulation of the secondary structure for desired circular ssDNA, the linear ssDNA substrate is designed to have its ends on the duplex part (≥5 bp). By using this permuted substrate with 5'-phosphate, the splint-free circularization is simply carried out by T4 DNA ligase. Very interestingly, formation of only several base pairs (2–4) flanking the nick is enough for ligation, although they form only instantaneously under ligation conditions. More significantly, the 5 bp intramolecular duplex part commonly exists in genomes or functional DNA, demonstrating the high generality of our approach. Our findings are helpful for understanding the mechanism of enzymatic DNA ligation from the viewpoint of substrate binding.

Clarifying the distribution of temperature and pressure in the wellbore and cavern during hydrogen injection and extraction is crucial for quantitatively assessing cavern stability and wellbore integrity. This paper establishes an integrated flow and heat transfer model for the cavern and wellbore during hydrogen injection and production, analyzing the variations in temperature and pressure in both the wellbore and the cavern. The specific conclusions are as follows. (1) The temperature and pressure parameters of hydrogen and natural gas within the chamber and wellbore were compared. Under identical injection and production conditions, the temperature of hydrogen in the chamber was 10°C higher than that of natural gas, and 16°C higher in the wellbore. The pressure of hydrogen in the chamber was 2.9 MPa greater than that of natural gas, and 2.6 MPa higher in the wellbore. (2) A comparative analysis was conducted on the impact of surrounding rock’s horizontal and numerical distance on temperature during hydrogen and natural gas injection processes. As the distance from the cavity increases, from 5 to 15 meters, the temperature fluctuation in the surrounding rock diminishes progressively, with the temperature effect in the hydrogen storage chamber extending at least 10 meters. (3) The influence of rock thermal conductivity parameters on temperature during the processes of hydrogen injection and natural gas extraction is compared. The better the thermal conductivity, the deeper the thermal effects penetrate the rock layers, with the specific heat capacity having the most significant impact.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

Pregnancy is a complex biological process which is associated with significant metabolic and hemodynamic changes of the maternal body which allow a normal fetal growth. The inability to adapt to these changes can affect the cardiovascular health. During pregnancy, women may experience mood swings, anxiety and emotional ambivalence. These symptoms can lead to stress and have a negative impact on the mental well-being of expectant mothers. It is crucial to know the aspects that can influence the development of cardiovascular problems among pregnant women in order to manage these cases properly. The current narrative review explores and summarizes the evidence regarding the impact of stress and anxiety on cardiovascular health in pregnant women. Understanding the physiological adaptations that the body undergoes throughout pregnancy is crucial for educating and supporting individuals as well as healthcare professionals. This enables them to recognize any risk factors or pathological conditions that may exacerbate pregnant women's health. In order to reduce maternal morbidity and mortality from cardiovascular disease, a psychological and cardiovascular risk factor screening that is done either before or during pregnancy may be able to identify situations that call for particular medical and/or psychological therapies.

Alzheimer's disease (AD) is a progressive neurodegenerative disorder characterized by cognitive impairment and memory loss. Oxidative stress (OS) has emerged as a central element in the pathophysiology of AD, linking various pathological features including amyloid-β (Aβ) plaque formation, tau hyperphosphorylation, and synaptic dysfunction. This review comprehensively examines the role of OS in AD, focusing on the mechanisms of reactive oxygen species (ROS) production, mitochondrial dysfunction, and their impact on neuronal integrity. Additionally, the review highlights recent advances in antioxidant therapy. Elevated ROS levels in the aging brain exacerbate oxidative damage to lipids, proteins, and DNA, contributing to neuronal atrophy and synaptic loss. Mitochondrial dysfunction further amplifies OS, disrupting cellular energy metabolism and promoting neurodegeneration. Despite the strong association between OS and AD, antioxidant therapies have shown inconsistent clinical outcomes. Emerging strategies targeting offer promising avenues for therapeutic intervention. This review highlights the need for a multifaceted approach in understanding and mitigating OS-related damage in AD, aiming to pave the way for more effective treatments and improved patient outcomes.

Understanding and controlling reproductive cycles and gonadal maturation in cultivated species are crucial in aquaculture. The sea urchin Paracentrotus lividus, known for its edible gonads, requires careful maturation control for both reproduction and commercialization. This study explores the impact of temperature, photoperiod, and diet on gonadal development to enhance year-round aquaculture practices. Using two independent cultivation systems, we manipulated environmental conditions to mimic different seasons. Sea urchins were exposed to natural or manipulated temperature and photoperiod conditions and fed either natural (Ulva spp.) or formulated diets. The gonadosomatic index (GI) and histological analysis assessed gonadal development. Results revealed a clear correlation between environmental conditions, diet, and gonadal maturation. Manipulated conditions accelerated maturation, with sea urchins showing advanced stages compared to natural conditions. Furthermore, sea urchins fed formulated diets exhibited higher GI values, indicating enhanced maturation. Histological analysis confirmed accelerated maturation, particularly in females. The study underscores the feasibility of controlling gonadal maturation through environmental manipulation and diet, enabling year-round marketable gonad production. Providing formulated diets rich in polyunsaturated fatty acids, notably docosahexaenoic acid (DHA), enhances commercial value. These findings optimize aquaculture practices for P. lividus, highlighting its adaptability to yield-maximizing production strategies. Understanding and controlling reproductive cycles and gonadal maturation in cultivated species are crucial in aquaculture. The sea urchin Paracentrotus lividus, known for its edible gonads, requires careful maturation control for both reproduction and commercialization. This study explores the impact of temperature, photoperiod, and diet on gonadal development to enhance year-round aquaculture practices. Using two independent cultivation systems, we manipulated environmental conditions to mimic different seasons. Sea urchins were exposed to natural or manipulated temperature and photoperiod conditions and fed either natural (Ulva spp.) or formulated diets. The gonadosomatic index (GI) and histological analysis assessed gonadal development. Results revealed a clear correlation between environmental conditions, diet, and gonadal maturation. Manipulated conditions accelerated maturation, with sea urchins showing advanced stages compared to natural conditions. Furthermore, sea urchins fed formulated diets exhibited higher GI values, indicating enhanced maturation. Histological analysis confirmed accelerated maturation, particularly in females. The study underscores the feasibility of controlling gonadal maturation through environmental manipulation and diet, enabling year-round marketable gonad production. Providing formulated diets rich in polyunsaturated fatty acids, notably docosahexaenoic acid (DHA), enhances commercial value. These findings optimize aquaculture practices for P. lividus, highlighting its adaptability to yield-maximizing production strategies.

In recent years, frequent occurrences of low temperature disasters due to global climate change have significantly impacted the normal growth of crops. Research has indicated that inorganic selenium (which is more toxic) can not only enhance the effects of low temperature stress but also increase selenium content on plants; however, there is a scarcity of studies investigating the impacts of organic selenium and nano-selenium on crops. In order to investigate whether organic selenium and nano-selenium can enhance low-temperature tolerance and increase selenium content in pak choi (Brassica chinensis var. pekinensis. cv. ‘Suzhouqing’), different concentrations (0, 5, 10, 20 mg L-1) of exogenous selenium were applied in this experiment to assess their effects on plant growth, nutritional quality and antioxidant properties. RNA-Seq technology was used to sequence the transcriptome of the leaves. Based on the transcriptome data, a Weighted Gene Co-expression Network Analysis (WGCNA) was employed to construct a network that associates with physiological traits related to stress resistance. Two highly correlated gene co-expression modules were identified, and within them, nine hub genes associated with endocytosis, antioxidant stress, absorption, transport, and metabolism of selenium were discovered. The results indicated that the beneficial effects on yield and total selenium content under low temperature were attributed to (1) protection of photosynthetic pigments for enhancing photosynthetic capacity by the up-regulation of LHca2, LHcb1, LHca1, LHcb4 in KEGG pathway: photosynthesis-antenna proteins; (2) activation of antioxidant system for efficient ROS homeostasis such as SOD, POD and CAT by the genes such as Superoxide dismutase, Monodehydroascorbate and (3) selenium absorption by endocytosis, seleninum transportation by ABC transporter gene family and selenium metabolism related genes such as Cysteine synthase, Glutaredoxin. These findings provide a foundation for further investigation into the molecular mechanisms underlying the effects of organic selenium and nano-selenium on cyanochloride production at low temperatures.

Salinity stress emerges as an important menace to global food security, particularly affecting susceptible crops such as common bean plants (Phaseolus vulgaris L.). The disruption of ion balances caused by salt stress withing plants cells reduces water and nutrient absorption, and hampers growth and productivity. Sacchorhiza polyschides, a brown macroalga rich in essential elements, and macrominerals, has drawn attention as a natural biostimulant, being a potential remedy to bolster crop resilience against salt stress. This study delves into the effect of water extracts of Sacchorhiza polyschides (SPE) across varying concentrations (1%, 2%, and 5%) in common bean plants under salt stress (68.4 mM NaCl) conditions. Two different methods of application were used: by spraying the aerial part of the plant or by irrigation together with the watering solution. The effects of both systems of application were studied on the aerial parts of the plants. SPE exhibited significant enhancements in morphological parameters, chlorophyll content, carbon-nitrogen activities, and antioxidant enzymatic system activities, alongside increasing osmolyte accumulation, compared to salt-stressed plants without biostimulation. Moreover, SPE reduced reactive oxygen species (ROS) levels caused by salt stress, mitigating lipid peroxidation. The concentrations of 2% and 5% SPE applied by spraying showed the most significant results in most of the parameters analyzed. By shedding light on the underlying science behind this biostimulant effect, this research underscores the potential of SPE to enhance crop resilience and augment food production in salt-challenged environments.

The DEAD-box RNA helicase DDX3X is a multifunctional protein involved in RNA metabolism and stress responses. In this study, we investigated the role of RG/RGG motifs in the dynamic process of liquid-liquid phase separation (LLPS) of DDX3X using cell-free assays and explored their potential link to cancer development through bioinformatic analysis. Our results demonstrate that the number, location, and composition of RG/RGG motifs significantly influence the ability of DDX3X to undergo phase separation and form self-aggregates. Mutational analysis revealed that the spacing between RG/RGG motifs and the number of glycine residues within each motif are critical factors in determining the extent of phase separation. Bioinformatic analysis of cancer genomic datasets uncovered a significant enrichment of DDX3X mutations in RG/RGG motifs across multiple cancer types, particularly in the N-terminal region of the protein. Furthermore, we found that DDX3X is co-expressed with the stress granule protein G3BP1 in several cancer types and can undergo co-phase separation with G3BP1 in a cell-free system, suggesting a potential functional interaction between these proteins in phase-separated structures. DDX3X and G3BP1 may interact through their RG/RGG domains and subsequently exert important cellular functions under stress situation. Collectively, our findings provide novel insights into the role of RG/RGG motifs in modulating DDX3X phase separation and their potential contribution to cancer pathogenesis.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (&gt;70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Early detection of neurological conditions is critical for timely diagnosis and treatment. Identifying cellular-level changes is essential for implementing therapeutic interventions prior to symptomatic disease onset. However, monitoring brain tissue directly through biopsies is invasive and high-risk. Bodily fluids such as blood or cerebrospinal fluid contain information in many forms, including proteins and nucleic acids. Particularly, cell-free DNA (cfDNA) has potential as a versatile neurological biomarker. Yet, our knowledge of cfDNA released by brain tissue and how cfDNA changes in response to deleterious events within the brain is incomplete. Mapping changes in cfDNA to specific cellular events is difficult in vivo, where many tissues contribute to circulating cfDNA. Organoids are tractable systems for examining specific changes consistently in a human background. However, few studies have investigated cfDNA released from organoids. Here, we examined cfDNA isolated from cerebral organoids. We found that cerebral organoids release quantities of cfDNA sufficient for downstream analysis with droplet-digital PCR and whole-genome sequencing. Further, gene ontology analysis of genes aligning with sequenced cfDNA fragments revealed association with terms related to neurodevelopment and autism spectrum disorder. We conclude that cerebral organoids hold promise as tools for the discovery of cfDNA biomarkers related to neurodevelopmental and neurological disorders.