Sulfate, the main dissolved contaminant in acid mine drainage (AMD), is ubiquitous in watersheds affected by coal and metal mining operations worldwide. Engineered passive bioremediation systems (PBS) are low-cost technologies that remediate sulfate contamination by promoting (1) precipitation of sulfate-bearing compounds, such as schwertmannite and gypsum; and (2) microbially-mediated sulfate reduction (BSR) to sulfide with subsequent precipitation of sulfide minerals. In this study, chemical and sulfur isotopic data are used to infer multiple pathways for sulfate sequestration in the Tab-Simco PBS. By simultaneously monitoring sulfate concentrations and δ34SSO4 values at four sampling points across the PBS, we (1) identified that the organic layer within the bioreactor was the primary site of BSR processes contributing to sulfate sequestration; (2) observed seasonal variations of BSR processes; (3) estimated that initially the BSR processes contributed up to 30% to sulfate sequestration in the Tab-Simco bioreactor; and (4) determined that BSR contribution to sulfate sequestration continuously declined over the PBS operational lifetime. Together, our results highlight the utility of combining geochemical and microbial fingerprinting techniques to decipher complementary processes involved in sulfur cycling in a PBS as well as the value of adding the sulfur isotope approach as an essential tool to help understand, predict, prevent and mitigate sulfate contamination in AMD-impacted systems.

Retrospective information about the climate system and plant ecophysiology are key inputs in climate and Earth system modelling. Dendrochronology provides such information with large spatiotemporal coverage, and stable carbon isotope (¹³C/¹²C) analysis across tree-ring series is among the most advanced dendrochronological tools. For the past seventy years, this analysis was performed on whole molecules, and, to this day, ¹³C/¹²C variation is attributed to ¹³C discrimination during CO₂ diffusion into leaves and assimilation by rubisco. By contrast, ¹³C discrimination by post-rubisco processes is presumed constant. Here, recently reported results on the first dataset of intramolecular ¹³C discrimination in tree rings were synthesised by variance component analysis. The emerging picture is not consistent with the classical (DR-discrimination-centred) concepts and practices of carbon-isotope dendrochronology. Specifically, leaf and stem post-rubisco discrimination each account for more variation in the data than diffusion-rubisco discrimination, i.e., post-rubisco discrimination is not constant. Furthermore, diffusion-rubisco discrimination is used widely as proxy of leaf intrinsic water-use efficiency (iWUE), a key determinant in the responses of global biogeochemical cycles to climate change. However, since diffusion-rubisco discrimination is a small component of the total data variance, whole-molecule analysis yields confounded iWUE estimates, yet intramolecular analysis will likely offer solutions. Lastly, all currently observed ¹³C/¹²C-climate relationships are attributed to diffusion-rubisco discrimination. However, here, relationships with temperature and radiation derive from leaf-level post-rubisco discrimination while relationships with precipitation derive from stem-level post-rubisco discrimination. That said, advances in mass spectrometry may soon make intramolecular ¹³C/¹²C analysis broadly available taking carbon-isotope dendrochronology to the next level.

Iron is an essential nutrient and necessary for biological functions from DNA replication and repair to transcriptional regulation, mitochondrial respiration, electron transfer, oxygen transport, photosynthesis, enzymatic catalysis, and nitrogen fixation. However, due to iron’s propensity to generate toxic radicals which can cause damage to DNA, proteins, and lipids, multiple processes regulate uptake and distribution of iron in living systems. Understanding how intracellular iron metabolism is optimized and how iron is utilized to regulate other intracellular processes is important to our overall understanding of a multitude of biological processes. One of the tools that the cell utilizes to regulate a multitude of functions is ligation of the iron-sulfur (Fe-S) cluster cofactor. Fe-S clusters comprised of iron and inorganic sulfur are ancient components of living matter on earth that are integral for physiological function in all domains of life. Here we will explore the ways in which the cell utilizes Fe-S clusters to sense the intracellular environment and respond to maintain equilibrium.

Paleoclimate information is key to understanding the climate system and predicting future climate. Currently, stable isotope analysis of whole molecules in tree rings is among the most advanced paleoclimate tools. Still, it only enables reconstructions of one climate parameter at a time (univariate climate reconstruction), a fundamental limitation. Here, we investigated whether this limitation can be overcome by analysing isotope variability at the level of intramolecular carbon positions in tree-ring glucose. We found that drought governs isotope variability at glucose C-1 to C-3, whereas radiation governs isotope variability at glucose C-5 to C-6. These isotope-climate relationships are statistically and mechanistically robust. According to cross-validation analysis, they can be reconstructed with high accuracy and precision. Thus, intramolecular isotope analysis enables multivariate climate reconstructions (proof of concept).

In organisms that use reduced sulfur compounds as alternative or additional electron donors to organic compounds, transcriptional regulation of genes for enzymes involved in sulfur oxidation is needed to adjust metabolic flux to environmental conditions. However, little is known about the sensing and response to inorganic sulfur compounds such as thiosulfate in sulfur-oxidizing bacteria. In the Alphaproteobacterium Hyphomicrobium denitrificans, one strategy is the use of the ArsR-SmtB-type transcriptional regulator SoxR. We show that this homodimeric repressor senses sulfane sulfur and that it is crucial for the expression not only of sox genes encoding the com-ponents of a truncated periplasmic thiosulfate-oxidizing enzyme system but also of several other sets of genes for enzymes of sulfur oxidation. DNA binding and transcriptional regulatory activity of SoxR are controlled by polysulfide-dependent cysteine modification. The repressor uses the formation of a sulfur bridge between two conserved cysteines as a trigger to bind and release DNA and can also form a vicinal disulfide bond to orchestrate a response to oxidizing conditions. The importance of the sulfur bridge forming cysteines was confirmed by site directed mutagen-esis, mass spectrometry and gel shift assays. In vivo, SoxR interacts directly or indirectly with a second closely related repressor, sHdrR.

Isotope detection and identification is paramount in many fields of science and industry, such as in the fusion and fission energy sector, in medicine and material science, and in archeology. The isotopic information provides fundamental insight on the research questions related to these fields as well as insight on product quality and operational safety. However, isotope identification with the established mass-spectrometric methods is laborious and requires laboratory conditions. In this work, Microwave-Assisted Laser-Induced Breakdown Spectroscopy (MW-LIBS) is introduced for isotope detection and identification utilizing radical and molecular emission. The approach is demonstrated with stable B and Cl isotopes in solids and H isotopes in liquid using emission from BO and BO2, CaCl, and OH molecules, respectively. MW-LIBS utilizes the extended emissive plasma lifetime and molecular emission signal integration times up to 900 s to enable use of low ~4 mJ ablation energy without compromising signal intensity and, consequently, sensitivity. On the other hand, long plasma lifetime gives time for molecular formation. Increase in the signal intensity towards the late microwave-assisted plasma was prominent in BO2 and OH emission intensities. As MW-LIBS is online-capable and requires minimal sample preparation, it is an interesting option for isotope detection in various applications.

The region of Eastern Europe & Turkey contributed to the SISAL (Speleothem Isotopes Synthesis and AnaLysis) global database with stable carbon- and oxygen isotope time-series from 18 entities from 14 cave systems. The currently available oldest record from this region is the ABA-2 flowstone record (Abaliget Cave; Hungary) reaching back to MIS 6. The temporal distribution of the compiled 18 entities points out a ~20-kyr-long period, centering around 100 ka, lacking speleothem stable isotope record in the region. The regional subset of SISAL_v1 records displays a continuous coverage for the past ~90 kyr for both δ¹⁸O and δ¹³C, with a mean temporal resolution of ~12 yr for the Holocene, and >50 yr for the pre-Holocene period. The highest temporal resolution both for the Holocene and the pre-Holocene was achieved in the So-1 record (Sofular Cave; Turkey). Assessing the data, an important split was found regarding the climatic interpretation of speleothem δ¹⁸O. While the oxygen isotope composition of more continental formations is thought to reflect mainly temperature variations and changes in moisture transport trajectories, it may strongly reflect fluctuations of precipitation amount in the southern part of the region. Variations of δ¹³C primarily interpreted as humidity changes reflecting dry/wet periods across the region. Elevation gradients from three non-overlapping time periods from the region - for the last 5kyr - indicated systematically prevailing elevational gradients around -0.26‰ 100m^-1 in δ¹⁸O. The regional comparison of SISAL_v1 speleothem δ¹⁸O and the temporal distribution of coarsely crystalline cryogenic cave carbonate occurrences back to 45ka does not appear to confirm the finding that occurrence of the latter coincides with the warming from stadial to interstadial conditions.

The preparation of sulfur-single walled carbon nanohorns active material via a simple and sustainable evaporation method for application as cathode in lithium-sulfur batteries is reported. We show that the synthesis process enables the infiltration of elemental sulfur within the carbon nanohorns thus obtaining a morphology responsible for the ameliorating of the shuttle effect. The sulfur-carbon composite is characterized in terms of structure, morphology, and composition through x-ray diffraction, transmission electron microscopy, and thermogravimetric analyses. From the electrochemical point of view, cyclic voltammetry, rate capability, and galvanostatic cycling tests are performed employing a solution of bis(trifluoromethane)sulfonimide lithium salt and lithium nitrate in a mixture of 1,2-dimethoxyethane and 1,3-dioxolane in order to evaluate the electrode design applicability within lithium-sulfur cells. In this respect, further insights are provided by the estimation of the lithium-ion diffusion coefficient through the Randles-Sevcik equation, and by electrochemical impedance spectroscopy. The obtained results reveal a remarkable cycle life lasting around 800 cycles with a stable capacity of 520 mA h g-1 for the first 400 cycles at C/4, while reaching a value around 300 mA h g-1 at the 750th cycle. These results suggest sulfur-carbon nanohorns active material as a potential candidate for the next-generation battery technology.

When oxidizing reduced sulfur compounds, the phototrophic sulfur bacterium Allochromatium vinosum forms spectacular sulfur globules as obligatory intracellular – but extracytoplasmic – intermediates. The globule envelope consists of three extremely hydrophobic proteins: SgpA and SgpB are very similar and can functionally replace each other. SgpC is involved in the expansion of the sulfur globules. The presence of a fourth protein, SgpD, has been suggested by comparative transcriptomics and proteomics of enriched sulfur globules. Here, we investigated the in vivo function of SgpD by coupling its carboxy-terminus to mCherry. This fluorescent protein requires oxygen for chromophore maturation, but we were able to use it in anaerobically growing A. vinosum provided the cells were exposed to oxygen for one hour prior to imaging. While mCherry lacking a signal peptide resulted in low fluorescence evenly distributed throughout the cell, fusion with SgpD carrying its original Sec-dependent signal peptide targeted mCherry to the periplasm and co-localized it exactly with the highly light-refractive sulfur deposits seen in sulfide-fed A. vinosum cells. Insertional inactivation of the sgpD gene showed that the protein is not essential for the formation and degradation of sulfur globules.

The biogeography of inflammation in ulcerative colitis (UC) suggests a proximal to distal concentration gradient of a toxin. Hydrogen sulfide (H2S) has long been considered one such toxin candidate, and dietary sulfur along with the abundance of sulfate reducing bacteria (SRB) were considered the primary determinants of H2S production and clinical course of UC. The metabolic milieu in the lumen of the colon, however, is the result of a multitude of factors beyond dietary sulfur intake and SRB abundance. Here we present an updated formulation of the H2S toxin hypothesis for UC pathogenesis, which strives to incorporate the interdependency of diet composition and the metabolic activity of the entire colon microbial community. Specifically, we suggest that the increasing severity of inflammation along the proximal-to-distal axis in UC is due to dilution of beneficial factors, concentration of toxic factors, and changing detoxification capacity of the host, all of which are intimately linked to the nutrient flow from the diet.

We report on magnetic studies of inhomogeneous commercial and synthesized amorphous carbon (a-C) and a-C doped with sulfur (a-CS) powders which exhibit (i) peculiar magnetic behavior and (ii) traces of two superconducting (SC) phase ~ Tc=33 and at 65 K. (i) The temperature dependence of zero-field-cooled (ZFC) curves measured up to room temperature show a well distinguish elusive peaks around 50-80 K, their origin is not yet known. These peaks are totally washed-out in the second ZFC sweeps and in the FC branches as well. As a result, in the vicinity of the peaks, the FC curves lie below the ZFC peaks (FC<ZFC), a phenomenon which is rarely observed. These magnetic anomalies are intrinsic properties of a-C and a-CS materials (ii) SC was observed in three different a-C sources: (a) The commercial a-C powder contains 0.21% of sulfur and it is suggested that two different a-CS phases (at 33 and 65 K) are the origin of the two SC states observed. The compositions of these two phases are not yet unknown. The small SC volume fractions of the 33 K phase can be enhanced by a solid reaction with additional sulfur at 250 ºC. (b) The synthesized a-C powder (obtained from decomposition of sucrose) is not SC. However, when mixed with sulfur and heated at 400 ºC under a protective atmosphere, the a-CS powder obtained also show traces of a SC phase at TC= 42 K. (c)The same occurs in a-C thin films. The as-grown films are not SC but a SC phase at Tc = 34 K emerges after the films were reacted with sulfur at elevated temperatures. It is concluded therefore, that all SC phases observed are due to different unknown a-CS phases. Since the a-C and a-CS powders possess SC and magnetic states, we believe that these powders resemble the high TC curates and Fe-As based systems in which the SC and the magnetic states are closed related to each other.

The discovery of water ice on the moon has revolutionized our understanding of lunar science and has profound implications for future space exploration and habitation. Through a comprehensive analysis of remote sensing data, isotopic studies, and neutron detection experiments, this research elucidates the presence, distribution, and origins of lunar water ice. Radar observations from missions like Clementine and Chandrayaan-1 reveal distinct polar regions with elevated circular polarization ratios, indicative of volatile ice deposits. Spectral detections by instruments such as M3 and Diviner further confirm the presence of water ice in lunar-shadowed regions, with estimates suggesting reserves of up to 300 million tons at the poles. Neutron detection experiments on lunar orbiters like LRO provide additional evidence, detecting hydrogen signals consistent with water ice below the lunar surface. Isotopic analyses offer insights into the origin and evolution of lunar water ice, with comparisons to cometary and asteroidal sources. Proposed missions, such as Artemis-3 and Artemis-4, aim to collect samples from the lunar South Pole for detailed isotopic analysis, furthering our understanding of lunar water ice's composition and history. Scientific data, including the lunar bulk water content and estimated water ice reserves, underscore the significance of lunar water ice as a critical resource for future space exploration endeavors. Calculations estimating the total water-ice area and water abundance near specific lunar features provide valuable insights into the potential utilization of lunar water ice for sustained human presence on the Moon and beyond.

In the recent rechargeable battery industry, lithium sulfur batteries (LSBs) have demonstrated promising candidate battery to serve as the next-generation secondary battery owing to its enhanced theoretical specific energy, economy, and environmental friendliness. Its inferior cyclability, however, which is primarily due to electrode deterioration caused by the lithium polysulfide shuttle effect, is still a major problem for the real industrial usage of LSBs. Optimization of the separator and functional barrier layer is an effective strategy for remedying these issues. In this article, the current progress based on classification and modification on functional separator is summarized. We will also describe their working mechanisms as well as the resulting LSB electrochemical properties. In addition, necessary performance for separators also will be mentioned in order to gain optimized LSB performance.

The emergence of various electronic devices and equipment such as electric vehicles and drones requires higher energy density energy storage devices. Lithium-sulfur batteries (LSBs) are considered as the most promising new generation energy storage system owing to high theoretical specific capacity and energy density. However, the severe shuttle behaviors of soluble lithium polysulfides (LiPSs) and the slow redox kinetics lead to low sulfur utilization and poor cycling stability, which seriously hinder the commercial application of LSBs. Therefore, various catalytic materials have been employed to solve these troublesome problems. High entropy materials (HEMs), as advanced materials, can provide unique surface and electronic structures that expose plentiful catalytic active sites, which opens new ideas for the regulation of LiPSs redox kinetics. Notwithstanding many instructive reviews in the land of LSBs, while this review aims to offer a complete and shrewd summary of the current progresses in HEMs-based LSBs, including in-depth interpretation of design principles and mechanistic electrocatalysis functions as well as pragmatic perspectives.

During the last forty years, the use of strontium isotopes in archaeology and biogeochemical research has spread widely. These isotopes, alone or in combination with others, can contribute to trace past and present environmental conditions. However, the interpretation of the isotopic values of strontium is not always simple and requires good knowledge of geochemistry and geology. This short paper on the use of strontium isotopes is aimed at those who use this tool (archaeologists, but not only) but who do not have a thorough knowledge of mineralogy, geology, and geochemistry necessary for a good understanding of natural processes involving these isotopes. We report basic knowledge and suggestions for a correct use of these isotopes. The isotopic characteristics of bio-assimilable strontium depend not so much on the isotopic characteristics of the bulk rock as, rather, on that of its more soluble minerals. Before studying human, animal and plant remains, the state of conservation and any conditions of isotopic pollution should be carefully checked. Samples should be collected according to random sampling rules. The data should be treated by a statistical approach. To make comparisons between different areas, it should be borne in mind that the study of current soils can be misleading since the mineralogical modification of the soil over time can be very rapid.

The equation of state of asymmetric nuclear matter as well as the neutron and proton effective masses and their partial-wave and spin-isospin decomposition are analyzed within the Brueckner–Hartree–Fock approach. Theoretical uncertainties for all these quantities are estimated by using several phase-shift-equivalent nucleon-nucleon forces together with two types of three-nucleon forces, phenomenological and microscopic. It is shown that the choice of the three-nucleon force plays an important role above saturation density, leading to different density dependencies of the energy per particle. These results are compared to the standard form of the Skyrme energy-density functional and we find that it is not possible to reproduce the BHF predictions in the (S,T) channels in symmetric and neutron matter above saturation density, already at the level of the two-body interaction, and even more including the three-body interaction.

Methane (CH4), produced endogenously in animals and plants, has recently been suggested to play a role in cellular physiology, potentially influencing the signaling pathways and regulatory mechanisms involved in nitrosative and oxidative stress responses. In addition, it has been proposed that supplementation of CH4 to organisms may be beneficial for the treatment of several diseases, including ischemia, reperfusion injury, and inflammation. However, it is still unclear if and how CH4 is produced in mammalian cells without the help of microorganisms, and how CH4 might be involved in physiological processes in humans. In this study, we provide first proof of the principle that CH4 is formed non-microbially in the human body by applying isotopically labeled methylated sulfur compounds, such as dimethyl sulfoxide (DMSO) and methionine, as carbon precursors to confirm cellular CH4 formation. A volunteer applied isotopically labeled (2H and 13C) DMSO on the skin, orally, and to blood samples. Monitoring of stable isotope values of CH4 convincingly showed the conversion of the methyl groups, as isotopically labeled CH4 was formed during all experiments. Based on these results, we consider several hypotheses about endogenously formed CH4 in humans, including physiological aspects and stress responses involving reactive oxygen species (ROS). While further and broader validation studies are needed, the results may unambiguously serve as a proof of concept for the endoge-nous formation of CH4 in humans by a radical-driven process. Furthermore, these results might encourage follow up studies to decipher the potential physiological role of CH4 and its bioactiv-ity in humans in more detail. Of particular importance is the potential to monitor CH4 as an ox-idative stress biomarker if the observed large variability of CH4 in breath air is an indicator for physiological stress responses and immune reactions. Finally, the potential role of DMSO as a radical scavenger to counteract oxidative stress caused by ROS might be considered in the health sciences. DMSO has already been investigated for many years, but its potential positive role for medical use remained highly uncertain.

The development of new target stations for radioisotope production based on a dedicated 70~MeV commercial cyclotron is described. Currently known as the South African Isotope Facility (SAIF), this initiative will free the existing separated-sector cyclotron (SSC) at iThemba LABS (near Cape Town) to mainly pursue research activities in nuclear physics and radiobiology. It is foreseen that the completed SAIF facility will realize a three-fold increase in radioisotope production capacity compared to the current programme based on the SSC.

Despite notable advancements in immunotherapy in the past decades, allogeneic hematopoietic stem cell transplantation (allo-HCT) remains a promising, potentially curative treatment modality. Only a limited number of studies has performed a direct comparison of two prevalent rabbit anti-thymocyte globulin (r-ATG) formulations — specifically, Thymoglobuline (ATG-T, formerly Genzyme) and Grafalon (ATG-G, formerly Fresenius). The primary objective of our retrospective analysis was to compare the outcomes of adult patients undergoing matched or mismatched unrelated donor (MUD/MMUD) allo-HCT, with a graft-versus-host disease (GvHD) prophylaxis based on either ATG-T or ATG-G. A total of 87 patients undergone allo-HCT between 2012 and 2022 were included. We observed no significant differences between ATG-T and ATG-G concerning the occurrence of acute graft-versus-host disease (aGvHD), regardless of its severity. Conversely, chronic graft-versus-host disease (cGvHD) occurred less frequently in the ATG-T group compared to ATG-G (7.5% vs. 38.3%, p=0.001). Patients treated with ATG-T manifested a higher incidence of cytomegalovirus (CMV) reactivations (70% vs. 31.9%, p&lt;0.001), with a shorter time between transplant and CMV (&lt;61 days, 77.8% vs. 33.3%, p=0.008) and a higher median CMV copy number (1000 vs. 0, p=0.004). Notably, despite a higher occurrence of CMV reactivations in the ATG-T cohort, most patients were asymptomatic compared to ATG-G (85.7% vs. 43.8%, p=0.005). Finally, we observed no significant differences in terms of 5-year overall survival (OS) and 3-year probability of relapse while comparing ATG-T and ATG-G (32.0% vs 40.3%, p=0.423; 63.9% vs 55.7%, p=0.438, respectively).

Sulfur, peroxide and combined sulfur and peroxide curing systems were applied for cross-linking of unfilled and carbon black filled rubber compounds based on ethylene-propylene-diene-monomer rubber. The results revealed that the type of curing system influenced the course and shape of curing isotherms. This resulted in the change of curing kinetics of rubber compounds. The cross-link density of vulcanizates cured with combined vulcanization systems was lower than that for vulcanizates cured only in the presence of sulfur or peroxide system. The results revealed good correlation between the cross-link density as well as the structure of the formed cross-links and physical-mechanical characteristics of the materials. It can be stated that by proper combination of vulcanization systems it is possible to modify tensile behavior of vulcanizates in targeted manner. On the other side, dynamical-mechanical properties were found not be significantly influenced by the composition of curing system.

The vulcanization of rubber compounds is an exothermal process. A carbon black-filled and natural rubber-based (NR) formulation was mixed with different levels of sulfur (0.5, 1.0, 2.0, 4.0 and 6.0 phr) and studied with Differential Scanning Calorimetry (DSC) for the determination of the vulcanization enthalpy. It was found that the vulcanization enthalpy is dependent from the amount of sulfur present in the compound and the vulcanization heat released was -18.4 kJ/mol S if referred to the entire rubber compound formulation or -46.0 kJ/mol S if the heat released is referred only to the NR present in the compound. The activation energy for the vulcanization of the rubber compounds was also determined by a DSC study at 49 kJ/mol and found quite independent from the sulfur content of the compounds under study. A simplified thermochemical model is proposed to explain the main reactions occurring during the vulcanization. The model correctly predicts that the vulcanization is an exothermal process although it gives an overestimation of the vulcanization enthalpy which is larger for the EV vulcanization package and smaller for the conventional vulcanization system. If the devulcanization is conducted mechanochemically in order to break selectively the sulfur-based crosslinks, then the natural rubber compounds recovered from used tires can be re-vulcanized again and the exothermicity of such process can be measured satisfactorily with DSC analysis. This paper not only proposes a simplified mechanism of vulcanization and devulcanization but also proposes an analytical method to check the devulcanization status of the recycled rubber compound in order to distinguish truly devulcanized rubber from reclaimed rubber.

We studied the dynamics of stable carbon (δ13C) and nitrogen (δ15N) isotopes in litters from Norway spruce (NSL) (Picea abies) and Scots pine (SPL) (Pinus silvestris) during in situ decomposition over a period of more than 4 years. Relative to initial values, δ13CNSL showed a weak enrichment (0.33‰), whereas δ13CSPL resulted in depletion (-0.74‰) at the end of decomposition. Both litter types experienced a depletion in δ15N during decomposition; δ15NNSL decreased by -1.74‰ and δ15NSPL decreased by -1.99‰. The effect of the selective preservation of or acid unhydrolyzable residue (AUR) in lowering δ13C of the residual litter was evident only in SPL. In the NSL, only in the initial stage C/N had a large effect on the δ13C values. In the later stages, there was a non-linear decrease in δ13CNSL with a simultaneous increase in AUR concentrations , but the effect size was large, suggesting the role of lignin in driving δ13C of residues in later stages. Depletion in 15N of the residual litters concomitant with the increase in N concentration suggests bacterial transformation of the litter over fungal components. A consistent decline in δ15N values further implies that bacterial dominance prompted this by immobilizing nitrate depleted in 15N in the residual litter.

Isotopic stable analysis (SIA) is a powerful tool in the assessment of different types of ecological and physiological studies. For that, different preservative methods for the samples are commonly used prior to isotopic analysis. The effects of various preservative methods (drying, freezing, ethanol and formaldehyde) have been analyzed for C:N ratio, δ13C and δ15N on a variety of tissues including dorsal fins (three seahorse and two pipefish species), seahorse newborns (three seahorses species), and prey (copepods and different stages of Artemia) commonly used to feed the fishes in rearing conditions. The aims of the study were to: (i) evaluate isotopic effects of preservation methods across tissues; and (ii) construct the first conversion models available in syngnathid fishes. The preservation in ethanol and to a lesser extend in formaldehyde significantly affected δ13C values, whereas δ15N signatures were not affected significantly. Due to their low lipid content, the isotopic signals in fish fins were almost unaffected, supporting the suitability of dorsal fins as a convenient tool in isotopic studies on vulnerable species such as syngnathids. The regression equations provided permit the successful conversion of δ13C and δ15N values between preservative treatments. The conversion models can be applied to isotopic studies in the field and in the laboratory.

Rubber compounds based on styrene-butadiene rubber, ethylene-propylene-diene-monomer rubber and the combinations of both rubbers were cured with different sulfur and peroxide curing systems. In sulfur curing systems, two type of accelerators, namely N-cyclohexyl-2-benzothiazole sulfenamide, tetramethylthiuram disulfide and combinations of both accelerators were used. In peroxide curing systems, dicumyl peroxide, and combination of dicumyl peroxide with zinc diacrylate or zinc dimethacrylate, respectively were applied. The work was focused on investigation of the curing system composition as well as type of the rubber or rubbers combinations on curing process, cross-link density and physical-mechanical properties of vulcanizates. The dynamic-mechanical properties on the selected vulcanizates were examined, too. The result revealed correlation between the cross-link density and physical-mechanical properties. Similarly, there was recorded certain correlation between cross-linking degree and glass transition temperature. The tensile strength of vulcanizates based on rubbers combinations was higher when compared to that based on pure rubbers, which points out the fact that by rubbers combination, not only the features of both elastomers can be combined, but also improved tensile characteristics can be achieved. When compared to vulcanizates cured with dicumyl peroxide, materials cured with sulfur system exhibited higher tensile strength. By application of co-agents in peroxide vulcanization, the tensile strength overcame the tensile behavior of sulfur cured vulcanizates.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

Diethyldithiocarbamate (DDTC) has been employed in the sulfide ore flotation process, due to its excellent collection performance. Herein, we investigated the interfacial adsorption behavior of DDTC on four mineral phases of high-sulfur residue — sulfur, pyrite, sphalerite and lead sulfate. The adsorption behavior — adsorption structure and energy and electron localization function cross section — of DDTC and H2O were explored using density function theory calculation. The result was helpful to construct a co-adsorption model of DDTC and H2O, which was validated by the pure minerals flotation operation and the characterization of fourier transform infrared spectra. The co-adsorption model indicated that the DDTC adsorption on the sulfur, sphalerite and lead sulfate was weak with physical bonding, while its adsorption on the pyrite was strong with chemical bonding. Practical bench-scale operation of high-sulfur residue flotation was performed, whose result was different from that obtained from the pure mineral flotation. To explain the difference, our developed model predictions and the mineral fugacity pattern analysis on the high-sulfur residue flotation were synergistically used. Overall, this work first proposed the co-adsorption model of DDTC and H2O and provided important insights into the interfacial adsorption in the high-sulfur residue flotation.

Elemental sulfur, commonly known for its wide range of biological activity, has a long history of being used to protect all garden and vegetable crops from a range of pests and diseases, including powdery mildew, ascochyta blight, clubroot, plant mites, oidium, anthracnose, and scab. In the present study, a quick and environmentally friendly approach has been developed for the synthesis of sulfur nanoparticles with antibacterial activity. Sulfur nanoparticles (SNPs) were prepared by modifying the surface of elemental sulfur using various polyelectrolyte-surfactant mixtures (PSM) including NaCMC-SDBS and PHMG-CTAB. The SNPs were characterized by UV–visible spectrophotometry, X-ray diffraction (XRD), and thermogravimetric analysis (TG/DSC), scanning electron microscopy (SEM), with the SNPs showing an almost spherical shape with an average size in the range of 150-200 nm. The antibacterial activity of the sulfur nanoparticles was tested using against gram-positive S. aureus and E. faecium and gram-negative E. coli and P. aeruginosa bacteria. From this, it could be seen that SNPs exhibited significant antimicrobial activity against gram-positive bacteria, i.e., S. aureus and E. faecium. The in vitro cytotoxicity of the SNPs-1 and SNPs-2 studied to normal (MeT-5A) and tumorous (MCF-7) human cell lines was assessed in the concentration range from 500 μg/ml to 0.12 mg/ml, from which it was determined as being non-cytotoxic. The received products can be considered for potential application in agriculture and medicine.

There have been many researches on the surface acoustic wave (SAW) sensors for detecting sulfur-containing toxic or harmful gases. This paper aims to give an overview of the current state of the polymer films used in SAW sensors for detecting deleterious gases. By covering most of the important polymer materials, the structures and types of polymers are summarized, and a variety of devices with different frequency, such as delay lines and array sensors for detecting mustard gas, hydrogen sulfide and sulfur dioxide are introduced. The preparation method of polymer films, the sensitivity of the SAW gas sensor, the limit of detection, the influence of temperature and humidity, and the anti-interference ability are discussed in detail. The advantages and disadvantages of the films are also analyzed, and the potential application of polymer films in the future is also forecasted.

This preliminary study introduces the incorporation and chemical stabilization of sulfur waste into geopolymers matrix and explores the concept of material production for further environmental and engineering solutions. Geopolymers were synthesized by dissolving sulfur in the alkaline activator of sodium hydroxide and sodium silicate in different proportions. The Alkaline solution was then mixed with metakaolin to synthesize the geopolymer matrix. Adding sulfur from 0 wt.% to 5 wt.%, compared with metakaolin, was found to lead to an increase in the compressive strength of the geopolymer from 22.5 MPa to 29.9MPa. When sulfur is between 5 wt.% and 15 wt.%, a decrease in compressive strength was observed to 15.7 MPa, which can be explained by defects and voids in the geopolymer microstructure through the solubility of excess sulfur and thus the formation of defects and voids in the geopolymer microstructure. Because of the incorporation of sulfur into the geo-polymer, a compact and dense microstructure is formed as reported in the SEM analysis. XRD analysis shows that besides quartz and Analcime, a new phase, Al2·H10·O17·S3, is also formed as a result of sulfur dissolution in alkaline activator of geopolymer.

Calcium (Ca) is an essential element constituting sedimentary carbonate in subducting sediments. Ca isotopic characteristics of subduction-related rocks could provide insight into the behavior and budget of carbonate and carbon cycles in subduction zones, due to the distinctive δ^44/40Ca ranges of sedimentary carbonate with respect to the mantle. Here, we studied the Ca isotopic compositions of arc magmas from the Northern Luzon arc (NLA), which are evolved from a depleted mantle metasomatized by slab-derived fluids and sediment melts. The δ^44/40Ca values range from 0.76 ± 0.04‰ to 1.01 ± 0.03‰ and cover the typical ranges for bulk silica earth (BSE, ~ 0.94‰) and fresh mid-ocean ridge basalt (MORB, ~ 0.83‰). The Ca isotopes of NLA volcanics are not dominantly determined by the effects of mantle partial melting or fractional crystallization, nor significantly modified by secondary alteration. Instead, the δ^44/40Ca values of NLA volcanics are controlled by the subduction-related metasomatism. The metasomatism by slab-derived fluids (mainly expelled from altered oceanic crust, AOC) dramatically elevated the contents of fluid-mobile elements (e.g., Ba and Pb) with respect to fluid-immobile elements (e.g., Ce). This process, however, rarely modified the Ca isotopes, possibly ascribed to the δ^44/40Ca similarity between AOC and the depleted mantle. The δ^44/40Ca values significantly correlated with subduction indicators (e.g., Sr-Nd isotopes, Ba/Nb, Ce/Pb, and Nb/La), demonstrating the Ca isotopes of NLA volcanics are mainly controlled by the metasomatism of sediment melts subducting from the South China Sea (SCS). Based on the thermal structures and chemical compositions of sediments subducting into global trenches, we propose that carbonate Ca isotopic signals can only be observed in the arcs with high sedimentary Ca fluxes and temperature-pressure conditions well beyond the solidus of H₂O-saturated sediment melting, e.g., NLA, Nicaragua, Guatemala, Colombia, Peru, South Chile, North Vanuatu, New Zealand, and Kermadec. The absence of such signals in other arcs suggests either limited sedimentary fluxes or much of the subducting sedimentary carbonate has been survived during plate subduction to enter the deep mantle.

The purpose of this study was to elucidate patterns and mechanisms driving seasonal and inter-annual variations of carbon and nitrogen stable isotopes in the zooplankton crustacean commu-nity of Lake Maggiore (Italy), during the period 2009-2020. Different zooplankton taxa and groups revealed different ranges of d13C signatures, giving an insight into food sources and niche partition. In particular, cyclopoids had a restricted range with most negative d13C‰ values and increase in d13C fractionation with the establishment of water thermal vertical stratification, high-lighting the importance of vertical distribution as key factor for taxa coexistence in a vertically heterogenous environment. d13C of the zooplankton community and of Daphnia were positively related to water temperature (R2=0.58 p <0.0001 and R2=0.68 p <0.0001, respectively) and d13C Daphnia signature to chlorophyll-a (R2=0.32, p < 0.0001). Decomposition of time series data for zooplankton carbon and nitrogen signatures and environmental parameters identified increasing trends in water temperature, chlorophyll-a and water conductivity and decrease in nitrate, that matched changes in carbon isotopic signature trend in some zooplankton taxa (Bosmina, Daphnia and diaptomids). Overall, the observed patterns in zooplankton isotopic signatures were interpreted as integrations of climate warming effects in Lake Maggiore, affecting both food sources availability and environmental conditions.

This research focuses on exploring generalized electron emissions in one-dimensional conducting materials, specifically examining field emission and thermionic emission. Additionally, the study investigates one-dimensional thermal radiation. The current density is derived for both one-dimensional thermionic emission and one-dimensional field emission. A generalized current density in one dimension is devised, taking into account arbitrary accelerating fields and temperature conditions. The formula for the one-dimensional current density is depicted with accelerating field and temperature across various work function materials. The current is also represented as a function of both temperature and electric field for various temperatures.

This work discussed the advantages of reducing copper in molten copper slag with low S content. FactSage calculated the distribution of copper at equilibrium under different sulfur content. The effect of sulfur content on copper recovery under different oxygen partial pressures was pointed out. The effect of sulfur content on copper recovery in the actual reduction process was explored through experimental research. Under the condition of low sulfur, the Recovery of copper and the stability of the experiment have an ideal results.

Mastitis-causing bacteria can establish persistent infections in the mammary gland of commercially important dairy animals despite the presence of strong specific humoral and cellular immune mechanisms. The aim of this study was to encapsulate vitamin D3 by complex coacervation with sulfur-saturated bovine lactoferrin-alginate using microbial transglutaminase-catalyzed crosslinking and investigate the oral administration of encapsulated vitamin D3 in blood serum biomarkers of the immune response in late-lactating dairy goats. Dairy goats (n = 18) in late lactation were randomly assigned to three experimental groups (n = 6), after balancing weight. Dairy goats were orally administered with 0.35 mg vitamin D3/day in the unencapsulated form and 0.35 mg vitamin D3/day in the encapsulated powder form. Another group received the basal diet. The experimental period lasted 6 weeks. The blood serum concentrations of 25-hydroxyvitamin D3 [25-(OH)-D3], lactoferrin, immunoglobulin A (IgA), and interferon-gamma (INF-γ) were measured. The delivery of vitamin D3 to dairy goats resulted in a marked increase of 25-(OH)-D3 concentration in serum while the serum level of lactoferrin also increased. Alternatively, the serum levels of IgA and the immunomodulatory cytokine INF-γ were elevated following supplementation with the encapsulated vitamin D3. Overall, the capsules in the powder form used in this study kept vitamin D3 highly bioavailable.

Cordyceps sinensis is one rare medicinal fungus produced in the Qinghai-Tibetan Plateau. Its quality and price varies hugely with different habitat, and its numerous substitutes have sprung up in functional food markets. This paper aims to discriminate the geographic origin of wild C. sinensis and its substitutes via the element analyzer-isotope ratio mass spectrometry and gas chromatography-isotope ratio mass spectrometry. The δ¹³C values of major fatty acids in the lipids of Cordyceps sinensis are characterized unanimously by the variation relation C_18:0 ﹤ C_18:2 ≈ C_16:0 ﹤ C_18:1; while their fluctuation intervals are notably different between those of neutral and polar lipids. The comparative analysis of the δ¹³C ratios of major fatty acids in lipids of Cordyceps sinensis suggests that the δ¹³C patterns may be sensitive potential indicators to discriminate its geographical origin. The δ¹³C values of individual major fatty acids of lipids from the cultivated stromata of Cordyceps militaris (SCM), the fermented mycelia of Hirsurella sinensis (FMH) and Paecilomyces epiali (FMP) range from −31.2‰ to −29.7‰, −16.9‰ to −14.3‰, and −26.5‰ to −23.9‰, respectively. Their δ¹³C pattern of individual major fatty acids may be used as a potential indicator to discriminate the products of natural C. sinensis and its substitutes.

Photocatalytic degradation plays a crucial role in wastewater treatment, and the key to achieving high efficiency is to develop photocatalytic systems that possess excellent light absorption, carrier separation efficiency, and surface-active sites. Among various photocatalytic systems, S-type heterojunctions have shown remarkable potential for efficient degradation. This work delves into construction of S-type heterojunctions of ternary indium metal sulfide and bismuth ferrite nanofibers with introduction of sulfur vacancy defects and morphology modifications to enhance the photocatalytic degradation performance. Through the impregnation method, BiFeO₃/Zn₂S₄ heterojunction materials were synthesized and optimized30% BiFeO₃/Zn₂S₄ heterojunction exhibited superior photocatalytic performance with higher sulfur vacancy concentration than Zn₂S₄. The in-situ XPS results demonstrate that the electrons between Zn₂S₄ and BFO are transferred via S-Scheme, and after modification, Zn₂S₄ has a more favorable surface morphology for electron transport, and its flower-like structure interacts with the nanofibers of BFO, which has a further enhancement of the reaction efficiency for degrading pollutants. This exceptional material demonstrated a remarkable 99% degradation of Evans blue within 45 min and a significant 68% degradation of ciprofloxacin within 90 min. This work provides a feasible idea for developing photocatalysts to deal with the problem of polluted water resources under practical conditions.

Sideroflexins (SLC56 family) are highly conserved multi-spanning transmembrane proteins inserted in the inner mitochondrial membrane in eukaryotes. Few data are available on their molecular function but, since their first description, they were thought to be metabolite transporters probably required for iron utilization inside the mitochondrion. Such as numerous mitochondrial transporters, sideroflexins remain poorly characterized. The prototypic member SFXN1 has been recently identified as the previously unknown mitochondrial transporter of serine. Nevertheless, pending questions on the molecular function of sideroflexins remain unsolved, especially their link with iron metabolism. Here, we review the current knowledge on sideroflexins, their presumed mitochondrial functions and the sparse - but growing - evidence linking sideroflexins to iron homeostasis and iron-sulfur cluster biogenesis. Since an imbalance in iron homeostasis can be detrimental at the cellular and organismal levels, we also investigate the relationship between sideroflexins, iron and physiological disorders. Investigating Sideroflexins’ functions constitutes an emerging research field of great interest and will certainly lead to main discoveries on mitochondrial physiopathology.

Biological nitrogen (N) provisioning is a seminal function of the gut microbes in several terrestrial insects, given the unbalanced carbon (C) and N ratios of their diets. Although freshwater insects face comparable dietary N limitations like terrestrial insects, little is known about this function by their gut microbiomes. In this study, we investigated microbial nitrate reduction to ammonium pathways as possible routes of biological N provisioning in two freshwater insects; filter-feeding Hydropsychidae and grazers/collectors Baetidae. After incubation in filtered (microbe-free) artificial stream water (ASW) containing dissolved ¹⁵N-labeled nitrate (treatment) or standard nitrate (control), bulk δ¹⁵N values of treatment samples (Baetidae = 100.62 ± 10.23, mean ± S.E.; Hydropsychidae = 76.82 ± 7.20) were significantly higher than controls (Baetidae = 10.14 ± 0.12 ; Hydropsychidae = 9.03 ± 0.20) in both functional feeding groups (F _{(3, 13)} = 296, P < 0.0001). The treatment δ¹⁵N values are cautiously interpreted as reflecting uptake and incorporation of microbe-derived ¹⁵N-metabolites (¹⁵NH₄ or ¹⁵N-amino acids) into host tissues following nitrate reduction to ammonium pathways in the gut lumen. Microbial nitrate reduction to ammonium activities was assessed via the quantification of dissimilatory (nrfA) and assimilatory (nasA) nitrate reduction to ammonium gene transcripts. There were no significant differences between control and treatment groups within each insect groups. Overall, this study provides a demonstration of the feasibility of applying ¹⁵N-stable isotope analysis for investigating, potential symbiotic functions of freshwater insect gut microbiomes, despite the preliminary nature of the results.

High intrinsic water use efficiency (WUEi), the ratio of leaf photosynthesis to stomatal conductance, may be a useful trait in adapting crops to water-limited environments. Carbon isotope ratios can be a useful indicator of WUEi, but might not be well correlated with it if the plants compared differ substantially in mesophyll conductance. In this study, six cultivars of soybeans previously shown to differ in WUEi in indoor experiments were grown in the field in Beltsville, Maryland, and mid-day WUEi was measured on nine clear days during mid-seasons of two years. Measurement dates were chosen for diverse temperatures, and air temperatures ranged from 21 to 34 oC on the different dates. Corrected carbon isotope delta values for 13C (CID) were determined on mature, upper canopy leaves harvested during early pod filling each year. WUEi differed among cultivars both years and the differences were consistent across measurement dates. Correlations between mean WUEi and CID were not significant in either year. It is concluded that consistent cultivar differences in WUEi exist in these soybean cultivars under field conditions, but that carbon isotope ratios may not be useful in identifying them.

The effect of four soil-applied sulfur [S; 100 mg S kg-1 soil (100S) and 200 mg S kg-1 soil (200S)] in different sources (elemental S, ammonium sulfate, gypsum or magnesium sulfate) in protecting mustard (Brassica juncea L. Czern &amp; Coss.) from cadmium effects was studied. Based on the observed reduction in growth and photosynthesis in plants subjected to 100 and 200 mg Cd kg-1 soil, B. juncea cv. Giriraj was selected as the most Cd-tolerant among five cultivars (namely, Giriraj, RH-0749, Pusa Agrani, RH-406, and Pusa Tarak). Sulfur applied to soil mitigated the negative impact of Cd on sulfur assimilation, cell viability and photosynthetic functions, with a lower lipid peroxidation, electrolyte leakage, and contents of reactive oxygen species (ROS: hydrogen peroxide, H2O2, and superoxide anion, O2•−). Generally, added S caused a higher activity of antioxidant enzymes (ascorbate peroxidase, catalase and superoxide dismutase), and contents of ascorbate (AsA) and reduced glutathione (GSH), and increases in the activities of their regenerating enzymes (dehydroascorbate reductase and GSH reductase), as well as rises in S assimilation, biosynthesis of non-protein thiols (NPTs) and phytochelatins (PCs). Compared to the other S-sources tested, elemental S more prominently protected B. juncea cv. Giriraj against Cd-impacts by minimizing Cd-accumulation and its root-to-shoot translocation; decreasing cellular ROS and membrane damage, and improving Cd-chelation (NPTs and PCs), so strengthening the defense machinery against Cd. The results suggest the use of elemental S for favoring the growth and development of cultivated plants also in Cd-contaminated agricultural soils.

In a two-year field trial, the effect of nitrogen (N) and sulfur (S) fertilization was investigated on grain yield, grain quality parameters, formation of acrylamide (AA), and the precursor free asparagine (Asn) in organically and conventionally produced winter wheat cultivars. In both production systems, different types, amounts, and temporal distributions of N were tested. While the effect of S fertilizer types and amounts on free Asn was only tested in the conventional farming system. Within both cropping systems, grain yield and baking quality were significantly influenced by N treatment while the effect on free Asn was only minor. Especially within the organic farming system, increasing N fertilization levels did not increase free Asn significantly. A slight trend of increasing free Asn levels with an intensified N supply was observed, especially in the presence of crude protein contents of 14% or higher. But only N amounts of 180 kg N ha⁻¹ or higher increased the probability of high free Asn contents considerably, while N supply below that amount led to free Asn values similar to the unfertilized controls. The results indicated that good baking quality can be achieved without significantly increasing free Asn levels. In addition, cultivars affected the levels of free Asn significantly. Compared to cv. “Bussard” and “Naturastar”, cv. “Capo” exhibited the lowest AA formation potential at an N supply of 180 kg N ha⁻¹ while simultaneously reaching a crude protein content > 15% (conventional) and > 12% (organic). Thus, it seems that cultivars differ in their ability to store and incorporate free Asn into proteins. Over all trials, a correlation of free Asn and AA was shown by R² = 0.77, while a relation of free Asn and protein was only R² = 0.36. Thus, lowering free Asn by adjusting N treatments should not necessarily affect baking quality. S nutrition within conventional farming did not change free Asn amount or crude protein significantly, probably due to the fact that soil was not sulfate-deficient. In summary, it was evident that free Asn amounts in wheat varied widely both within cultivars and between cropping systems. In order to clearly unravel genotypic differences and their interaction with environmental factors and especially N fertilization, further research is needed.

Global warming poses a threat to plant survival, impacting growth and agricultural yield. Protein turnover, a critical regulatory mechanism balancing protein synthesis and degradation, is crucial for cellular response to environmental changes. We investigated the effects of elevated temperature on proteome dynamics in Arabidopsis thaliana seedlings using 15N-stable isotope labeling and ul-tra-performance liquid chromatography-high resolution mass spectrometry, coupled with the ProteinTurnover algorithm. Analyzing different cellular fractions from plants grown under 22°C and 30°C growth conditions, we found significant changes in the turnover rates of 571 proteins, with a median 1.4-fold increase, indicating accelerated protein dynamics under thermal stress. Notably, soluble root fraction proteins exhibited smaller turnover changes, suggesting tissue-specific adap-tations. Significant turnover alterations occurred with redox signaling, stress response, protein folding, secondary metabolism, and photorespiration, indicating complex responses enhancing plant thermal resilience. Conversely, proteins involved in carbohydrate metabolism and mito-chondrial ATP synthesis showed minimal changes, highlighting their stability. This analysis high-lights the intricate balance between proteome stability and adaptability, advancing our under-standing of plant responses to heat stress and supporting the development of improved thermo-tolerant crops.

Cuboid diamonds are particularly common in the placers of the northeastern Siberian platform but their origin remains unclear. These crystals usually range in color from dark yellow to orange and more interestingly, are characterized by unusual low aggregated nitrogen impurities (non-aggregated C-center) suggesting a short residence time and/or low temperatures at which they have been stored in the mantle. In order to track possible isotopic signature that could help deciphering cuboid diamond's crystallization processes, δ¹³C values, δ¹⁵N values and nitrogen contents have been determined in-situ in three samples using secondary ion mass spectrometry (SIMS), whereas nitrogen aggregation state have been determined by FTIR spectroscopy. The samples fall out the δ¹³C vs. δ¹⁵N field of canonical mantle composition. Different scale of carbon and nitrogen fractionation may produce the observed variations. Alternatively, mixing of mantle and crustal material would obscure initial co-variations of δ¹³C values with δ¹⁵N or nitrogen content.

Compound-specific isotope analysis (CSIA) can provide unique insights into the cycling of elements including carbon and nitrogen. One approach for CSIA is the use of high-performance liquid chromatography (HPLC) to separate compounds of interest, followed by analysis of these compounds using an elemental analyzer coupled to an isotope ratio mass spectrometer. A key component of this technique is the fraction collector, which automatically collects compounds as they are separated by HPLC. Here we present a fraction collector which is a simple adaptation of a 3D printer, and thus can be easily adopted by any laboratory already equipped for HPLC. In addition to the much lower cost compared to commercial alternatives, this adaptation has the advantage for CSIA that the 3D-printer is able to heat the collected fractions, which is not true for many commercial fraction collectors. Heating allows faster evaporation of the solvent, so that the dried compounds can be measured by EA-IRMS immediately. The procedure can be repeated consecutively so that dilute solutions can have the compounds concentrated for analysis. Any computer-controlled HPLC can be integrated to the fraction collector used here by means of AutoIt.

Copper(I) sulfide (Cu2S) is a low-cost, earth-abundant, and non-toxic thermoelectric material for applications in the middle-high temperature range (&gt;650 K). Although 3D printing these materials can simplify their manufacturing, elevated temperatures observed during sintering impair their crystal structure and energy conversion efficiency. In this study, we demonstrated a novel post-processing methodology to revert the thermoelectric properties of the 3D printed Cu2-xS materials back to the unimpaired state via sulfur infusion. After printing and sintering, sulfur was infused into the specimens under vacuum to optimize their crystal structure and achieve high thermoelectric efficiency. Chemical analysis and X-ray Diffraction (XRD) tests showed that after the sulfur infusion process, the Cu/S ratio was reverted close to the stoichiometric level. 3D printed Cu2-xS showed p-type thermoelectric behavior with electrical conductivity peaking at 143 S-cm-1 at 750 K and Seebeck coefficient of 175 µV-K-1 at 627 K. Figure of merit (ZT) value of 1.0 at 780 K was achieved which is the highest value ever reported for a 3D printed Cu2-xS thermoelectrics at this temperature. Fabrication of environmentally friendly thermoelectric materials with extended dimensional freedom and conversion efficiency has the potential to impact the thermoelectric industry with new energy conversion applications and lowered manufacturing costs.

The decline in Pinus sylvestris var. mongolica in the introduction area has had a high profile in recent years. For the ecological restoration, management and silvicultural design of Mongolian pines in the introduction area, it is necessary to conduct a comprehensive and in-depth study on the ecological adaptation mechanism of Mongolian pines in provenances. The ecological process of water and nutrient accumulation as well as the influence of environmental factors on the photosynthetic physiology are the key to revealing the ecological adaptation mechanism of Mongolian pines. According to the differences of climate in the distribution area of Mongolian pines, sampling sites were set up, the effects of environmental factors on leaf δ13C and the relationship between leaf δ13C and nutrient content were analyzed. The results showed that leaf δ13C values were ranging from - 29.7 ‰ to - 23.76 ‰. The ecological stoichiometry, including LC (522.81 mg·g-1), LN (16.04 mg·g-1), LP (1.19 mg·g-1) and L-N:P (13.56), indicated that leaf photosynthesis and water use efficiency is greatly affected by environmental conditions, Mongolian pines had strong ability of carbon fixation, and its growth was obviously restricted by nitrogen. Although there was no significant correlation between δ13C with stoichiometric parameters in leaf, photosynthesis was the key link in the process of carbon fixation. It also showed that Pinus sylvestris var. mongolica was a stomatal limited plant. Leaf δ13C had significant correlation with climatic factors. VPD is the dynamic factor affecting the photosynthetic physiological process in leaves. Air and soil moisture are the dominate factors affecting the leaf stomatal conductance and determines leaf δ13C value, while other factors indirectly affect leaf δ13C by its impact on relative humidity or soil water content. Soil phosphorus content affected by clay is a key factor affecting soil water availability and soil nutrient cycling. Photosynthetic process in leaf is the dynamic process affecting the nutrient accumulation.

Sulfur and selenium-containing organic compounds (amino acids and xenobiotics) have received interests as potential medicines, sources of the selenium and antioxidants. The purpose of the study was to comparatively investigate the antioxidant capacity of sulfur- and selenium-containing amino acids, xenobiotics and the study of possible mimetic properties of selenocystine. To evaluate the antioxidant capacity, coulometric oxidation with electrogenerated bromine was used. Methionine, cystine and selenocystine react with bromine quickly and quantitatively. Diacetophenonyl selenide, ebselen and selenopyran are oxidized nonstoichiometrically, but show high antioxidant capacity. We hypothesized that selenium xenobiotcs might be exert prolonged antioxidant effect. Conditions have been optimized to determine antioxidant capacity of selenium and sulfur substances in water and methanol. We proposed theory and reactions schemes for the interaction of bromine with methionine, cystine, selenocystine diacetophenonylselenide, ebselen, thiopyran and selenopyran. Antioxidant capacities in both water and methanol decrease in the following order: L-cystine &gt; L-selenocystine &gt; methionine. Sulfur-containing substances in methanol show higher antioxidant capacity than selenium-containing antioxidants. Among selenium-containing xenobiotics, DAPS shows the highest antioxidant capacity (comparable to cystine). Selenopyran and ebselen are less active as antioxidants. Diselenide bond is a selenocystin chromophore for its UV-assay. For the first time we demonstrated the ability of selenocystine to be actively involved in redox reactions and to act as a mimetic, a low-molecular-weight analogue of glutathione peroxidase.

The present study was conducted to investigate the comparative effects of organic and inorganic forms of sulfur, methyl sulfonyl methane (MSM) and sodium sulfate (SS), on laying performance, egg quality, ileal morphology, ileal volatile fatty acids, and antioxidant and stress markers in various biological samples in aged laying hens. A total of 144, 73-week-old Lohman Brown-Lite laying hens were randomly assigned to one of three experimental diets: basal diet (CONT), CONT + 0.2% MSM (MSM), and CONT + 0.3% SS (SS). The trial lasted for 12 weeks. MSM and SS groups contained 0.07% of sulfur, either organic or inorganic. Dietary MSM did not affect egg production and feed conversion ratio at 12 weeks compared with the CONT group. Dietary sulfur did not affect egg quality except for Haugh unit at 4 weeks which was lowered (P &lt; 0.05) in the SS group. Compared with the CONT group, higher (P &lt; 0.05) villus height and crypt depth ratio was observed in the SS group. None of dietary sulfur affected the percentages of short-chain fatty acids in the ileum. Total antioxidant capacity of liver increased (P &lt; 0.05) in laying hens fed MSM- and SS-added diets compared with the CONT group. The MSM and SS groups lowered (P &lt; 0.05) malondialdehyde (MDA) concentration in serum samples compared with the CONT. Finally, dietary MSM had the lowest (P &lt; 0.05) MDA concentrations in yolk samples. Taken together, our study showed that dietary organic and inorganic sulfur have positive effects on ileal morphology and antioxidant capacity in laying hens. However, SS-mediated inhibition in laying performance needs to be clarified.

The study aimed to elucidate the optimum level of elemental sulfur, fresh cassava root (FCR), and urea and their effect on gas production, ruminal fermentation, thiocyanate concentration, and in vitro degradability. A 3×2×4 in a completely randomized design were conducted. Factor A was level of sulfur at 0%, 1%, and 2% of concentrate dry matter (DM), factor B was level of urea at 2% and 4% of concentrate DM, and factor C was level of the FCR at 0, 200, 300, and 400 mg of the total substrate. The study found that elemental sulfur, urea, and FCR had no interaction effect on the kinetics of gas, ruminal fermentation, hydrogen cyanide (HCN), and in vitro degradability. Elemental sulfur supplementation (P<0.05) significantly increased the gas produced from an insoluble fraction (b), in vitro DM degradability and either neutral detergent fiber or acid detergent fiber degradability, and propionate (C3) concentration while decreased the ruminal HCN concentration. Urea levels showed a (P<0.05) significant increase of the potential extent of gas production, ruminal NH3-N, and total volatile fatty acid (VFA). FCR supplementation (P<0.05) significantly increased the gas produced from an immediate soluble fraction (a), gas produced from insoluble fraction, gas production rate constant, total VFA, C3 concentration, and HCN while decreased ruminal pH, acetate, and butyrate concentration. It could be concluded that 2% elemental sulfur, 4% urea, and 300 mg FCR showed a greater effect on gas production, ruminal fermentation, and HCN reduction.

Pipefishes (Family Syngnathidae) are representative fishes in many European coastal areas asso-ciated with vegetal assemblages and other shallow habitats. The polyandrous pipefishes Syngnathus abaster and S. acus co-occur in Metruk Tuzla (Bargilya Wetland, Aegean Sea, Turkey), a protected but threatened wetland due to anthropogenic disturbances. Both species were sam-pled during the breeding season (April-2018 and June-2019) for the assessment of growth and trophic features revealed from stable isotope profiles (δ13C and δ15N) and gut content. Both species showed positive allometric growth, with similar length-weight relationships. The isotope approach indicated that both species occupy similar trophic niches, with mean δ13C and δ15N values of -17.0 ± 1.2 ‰ for δ13C and 13.2 ± 0.6 ‰ for δ15N in S. abaster, and -17.3 ± 1.2 ‰ for δ13C and 13.3 ± 0.7 ‰ for δ15N in S. acus. The niche area for all sex types (undifferentiated specimens, males and females) in S. acus was slightly broader than in S. abaster. The simulation analysis of the trophic position (TP) in both species agreed with the isotopic assessment (TP = 3.67 ± 0.61 in S. abaster and 3.46 ± 0.66 in S. acus). Despite the high trophic resemblance between S. abaster and S. acus, the gut content assessment revealed the large contribution of copepods (especially Calanipeda aquaedulcis) to the dietary regime in both pipefishes. However, while the diet in S. abaster seemed to be almost monospecific, cladocerans were also an important resource in S. acus. Hence, we suggest that potential inter-specific competition for dietary resources would be minimized likely due to the occupancy of different microhabitats, a hypothesis that needs to be confirmed by further research.

Relations between nutrient assimilation and growth rate in fishes may vary with abiotic factors such as temperature. The effects of feeding status, ontogeny and temperature regimes (15, 18 and 21 °C) on stable isotope (δ13C and δ15N) patterns were assayed and modelled in juveniles of the seahorse Hippocampus guttulatus. The use of effective day degrees (D°eff) and chronological time (age) were compared as development progress indices. Newborn seahorses were maintained at three temperature levels both deprived of food (5 days) or fed (30 days) on copepods or/and Artemia. Isotopic signatures in fed seahorses clearly differed from those in unfed juveniles. Temperature had a significant effect on δ13C values in fed juveniles throughout the experimental period. δ15N values also varied significantly with age, but not with temperature level. Faster growth and food assimilation in seahorses held at 18 and 21 °C were supported by faster variations in isotopic values. Our findings demonstrate that effective day degrees should be preferred over chronological time as index of developmental progress in temperature fluctuating scenarios or for comparative studies.

Viruses rely on host cells to replicate their genomes and assemble new viral particles. Thus, they have evolved intricate mechanisms to exploit host factors. Host cells, in turn, have developed strategies to inhibit viruses, resulting in a nuanced interplay of co-evolution between virus and host. This dynamic often involves competition for resources crucial for both host cell survival and virus replication. Iron and iron-containing cofactors, including iron-sulfur clusters, are known to be a heavily battled resource during bacterial infections where control over iron can tug the war in favor of the pathogen or the host. It is logical to assume that viruses also engage in this competition. Surprisingly, our knowledge about how viruses utilize iron (Fe) and iron-sulfur (FeS) clusters remains limited. The handful of reviews on this topic primarily emphasize the significance of iron in supporting the host immune response against viral infections. The aim of this review, however, is to organize our current understanding of how viral proteins utilize FeS clusters, to give perspectives on what questions to ask next and to propose important avenues for future investigations.

This research was specifically aimed at assessing the influence of sulfur in triple-super phosphate (TSP) on wheat yield. From the results, wheat showed response to sulfur (S) from gypsum (in 67%); and nitrogen (N) from urea in about 100% (of 24 sites). Based on this N was found to be the most limiting element to wheat production followed by sulfur, and then by phosphorus. TSP is tested to contain agronomically up to 2-6% by weight of S. However, wheat didn’t show response to S impurity supplied in the form of TSP. Though, not statistically significant, it is observed that there have always been yield increments by certain percent due to S from TSP in 8 out of 10 target sites, which is depicted in the increasing trends of yield response curves. From this it is learnt that, the benefits of the accidental/incidental application of such high analysis fertilizers can be many-folds in the quality attributes of wheat, if the soils of such investigation at the same time would contain significant amount of organic matter (OM). Indeed, such analysis would be vital in varietal specific nutrient requirement studies in precision-farming and/or in categorizing soils into fertility gradients and fertilizer recommendation domains.

To remove sulfur-containing compounds (SCC) from the diesel fraction 200-360 °C extraction systems have been created based on coordinating organic solvents - dimethylformamide and dimethylsulfoxide and chlorides (CoCl2, CuCl2, CdCl2, MnCl2 and CrCl3) and metal trifluoroacetates (Co (TFA)2, Cu(TFA)2 and Mn(TFA)2). Using PMR spectroscopy the coordination of chloride and metal trifluoroacetate on the oxygen atom in the carbonyl group of DMFA was shown to redistribute electron density in the solvent molecule and to enhance properties of the acceptor center localized on the nitrogen atom. The removal of sulfur-containing compounds from the diesel fraction proceeded under mild conditions - at the temperature of 25 °C and atmospheric pressure. The degree of SCC removal from the diesel fraction in 30 minutes extraction was more than 90%. The interaction of organic solvents with metal salts and sulfur-containing compounds of the diesel fraction was considered within the framework of the concept of "hard and soft acids and bases" (HSAB). The most complete SCC extraction was carried out by "DMFA - Mn(TFA)2, MnCl2 and CrCl3 systems, that was probably connected with the implementation of the" hard base - hard acid "system.

Indium-catalyzed reaction of lactones and a disilathiane leading to thiolactones is described. The direct synthesis of thiolactones from lactones with an appropriate sulfur source is one of the most attractive approaches in organic and pharmaceutical chemistry. In this context, we found an indium-catalyzed direct conversion of lactones into thiolactones in the presence of elemental sulfur and a hydrosilane via formation of the disilathiane in-situ. On the basis of the previous reaction, the application utilizing the disilathiane as a sulfur source was performed herein for the efficient synthesis of a variety of thiolactone derivatives from lactones by an indium-catalyst.

Microbial populations involved in forming the distinctive precipitates of the S, Fe, Mn, and Ca cycles in the San Diego River watershed reflect an interplay between mineralogy of the rocks in the watershed, sparse rainfall, ground- and surface-water anoxia, and runoff of high sulfate, treated imported water. In the less developed headwaters, Temescal Creek tributary emerges from pyrite-bearing metamorphic rocks, and thus exhibits both an oxidized Fe and reduced S cycle. In the middle reaches, the river moves through developed land where treated, imported high sulfate Colorado River water enters from urban runoff. Mast Park surrounded by caliche-bearing sedimentary rocks is a site where marl is precipitating. Cobbles in riffles in the river are coated black with Mn oxide. When the river encounters deep-seated volcanic bedrock, it wells up to precipitate both Fe and Mn oxides at Old Mission Dam. Then, directly flowing through caliche-laced sedimentary rocks, Birchcreek tributary precipitates tufa. Further downstream, at a site that periodically receives full sunlight, a sulfuretum sets up during the summer when the river is deoxygenated. Such a rich geochemistry results in activity of iron and manganese oxidizing bacteria, sulfur oxidizers and reducers, and cyanobacteria precipitating calcareous marl and tufa.

Nitrogen (N) and sulfur (S) are essential macro-elements crucial for the proper development, productivity, nutrient uptake, and the building blocks of protein biosynthesis. The plant's N-metabolism is also influenced by S, and its deficiency can lead to a decline in the consumption of N from fertilizers. The objective of this research was to assess the impacts Temporal N and S applications on the nutrient uptake, productivity, use efficiencies and micronutrients content status in soybean seeds. The field trial in randomized complete block design carried out, experiment comprised fourteen treatments with varying N and S quantities. N and S were applied through starter and temporal applications in different combinations. The findings indicated that temporal application of individually N and S fertilization as 25 kg ha-1 as starter and 25 kg ha-1 as temporal applications at R2 stage enhanced the highest nutrient uptake, seeds and stalks yields. The use efficiencies, as well as the Zinc (Zn) and iron (Fe) uptake by seeds, showed an increase with the temporal application of both nutrients compared to the control. Furthermore, soil Zn and Fe contents were also enhanced with the temporal applications of nitrogen and sulfur fertilization. As a result, it could be decided that the nitrogen and sulfur temporal applications not only enhanced nutrient uptake, productivity and use efficiencies but also improved the micronutrient uptake by soybean. Furthermore, this practice contributed to an improvement in soil Zn and Fe content.

In eutrophic waters, such as Mikawa Bay, Japan, anoxic bottom water develops in summer. This causes sulfide release into seawater by sulfate reduction in the sediment, leading to environmental problems. The addition of iron to sediments is a method used to improve the sediment environment, which was devised from a natural phenomenon. However, this method has not yet been quantitatively evaluated. In this study, we aim to quantitatively evaluate the suppressive effect of iron on sulfide release. First, we develop a sediment model that focuses on S and Fe. We then attempted to reproduce the observations and experiments on sulfide dynamics using the model. Consequently, the proposed model was able to reproduce field sulfur and Fe dynamics in sediments. Additionally, the model described the characteristics of sulfide release considering the effects of additive iron materials. Finally, we conducted predictive calculations and quantitatively evaluated the effects of adding iron materials to the sediments in terms of sulfur and iron cycles.

Milling and mining metal ores are major sources of heavy metal contamination. The Spring River and its tributaries in southeast Kansas are contaminated with Pb, Zn, and Cd as a result of 120 years of mining activities. Trace metal transformations and cycling in mine waste materials greatly influence their mobility and toxicity and affect plant productivity and human health. It has been hypothesized that under reduced conditions in sulfate-rich environments, these metals can be transformed into their sulfide forms, thus limiting mobility and toxicity. We studied biogeochemical transformations of Pb, Zn and Cd in flooded subsurface mine waste materials, natural or treated with organic carbon (OC) and/or sulfur (S), by combining advanced microbiological and X-ray spectroscopic techniques to determine the effects of treatments on the microbial community structure and identify the dominant functional genes involved in the biogeochemical transformations, especially metal sulfide formation over time. Samples collected from medium-, and long-term submerged columns were used for microarray analysis via functional gene array (GeoChip 4.2). The total number of detected gene abundance decreased under long-term submergence, but major functional genes abundance was enhanced with OC plus S treatment. The microbial community exhibited a substantial change in structure in response to OC and S addition. Sulfur-reducing bacteria genes dsrA/B were identified as key players in metal sulfide formation via dissimilatory sulfate reduction. Uniqueness of this study is that microbial analyses presented here in details are in agreements with molecular-scale synchrotron-based X-ray data supporting that OC-plus-S treatment would be a promising strategy for reducing metal toxicity in mine waste materials.

The paper presents the results of modeling the problem of injecting liquid sulfur dioxide into a porous reservoir initially saturated with methane and ice. The model presented in the paper assumes the formation of three different regions, namely, the near one, saturated with liquid SO2 and its hydrate; the far one, containing methane and ice, and the intermediate one, saturated with methane and water. The effects of various parameters of the porous medium and injected SO2 on the nature of the course of the hydrate formation process have been studied. It is shown that with a decrease in reservoir permeability or injection pressure, the length of the intermediate region decreases, which in the limiting case means the formation of SO2 hydrate in the mode without the formation of an extended region saturated with methane and water. It is shown that such a regime is also typical for the case of high initial injection pressures, as well as low values of the initial reservoir temperature and injection temperature.

To mitigate lithium dissolution and polysulfide shuttle effect phenomena in high energy lithium sulfur batteries (LISBs), a conductive, flexible, and easily modified polymer composite layer was applied on the anode. The polymer composite layer includes polyaniline and functionalized graphite. The electrochemical behavior of LISBs was studied by galvanostatic charge/discharge tests from 1.7 to 2.8 V up to 90 cycles and via COMSOL Multiphysics simulation software. No apparent overcharge occurred during the charge state, which suggests that the shuttle effect of polysulfides was effectively prevented. The COMSOL Multiphysics simulation provides a venue for optimal prediction of the ideal concentration and properties of the polymer composite layer to be used in the LISBs. The testing and simulation results determined that the polymer composite layer diminished the amount of lithium polysulfide species and decreased the amount of dissolved lithium ions in the LISBs. In addition, the charge/discharge rate of up to 2.0 C with a cycle life of 90 cycles was achieved. The knowledge acquired in this study was important not only for the design of efficient new electrode materials, but also for understanding the effect of the polymer composite layer on the electrochemical cycle stability.

Diesel, gas oil, whole crudes, and bitumen samples were subjected to sulfoxidation, and then subjected to hydroxide attack in the presence of ethylene or propylene glycol. The resultant oils were analyzed by XRF for total sulfur and XANES spectroscopy for sulfur speciation at each stage. The combination of these analyses gave the total amount of sulfur as organic sulfide, sulfoxide, and sulfone at each stage of treatment so as to determine the effectiveness of the desulfonylation for sulfur compounds of different oxidation states.

The results of an LA-ICP-MS U-Pb dating and Hf isotope study of zircon crystals separated from small eclogite xenoliths found in Devonian kimberlites within the Prypyat horst, Ukraine, are reported. The studied area is located in the Central Belarusian Suture Zone, which represents a Paleoproterozoic belt extending along the boundary between the Sarmatian and Fennoscandian segments of the East European Platform. Four laser ablation sites on two zircon grains yielded Paleoproterozoic U-Pb ages between 1954 ± 24 Ma and 1735 ± 54 Ma. In contrast, three of four Hf sites revealed negative εHf values and Paleoarchean to Mesoarchean model ages, excluding the possibility that the eclogite xenoliths represent segments of a Paleoproterozoic subducted slab or younger mafic melts crystallized in the subcontinental lithospheric mantle. A single laser ablation Hf spot yielded a positive εHf value (+3) and a Paleoproterozoic model age. Two models for eclogite origin can be proposed. The first foresees the extension of the Archean lower-crustal or lithospheric roots beneath the Central Belarus Suture Zone for over 200 km from the nearest known outcrop of Archean rocks. The second model is that the Central Belarus Suture Zone represents a rifted-out fragment of the Kola-Karelian craton that was accreted to Sarmatia before the actual collision of these two segments of Baltica.

Porphyromonas spp. are oral anaerobic Gram-negative bacteria that form black-pigmented colonies on blood agar and produce volatile sulfur compounds (VSCs), such as hydrogen sulfide (H2S), methyl mercaptan (CH3SH), and dimethyl sulfide ((CH3)2S), which cause halitosis and the destruction of periodontal tissues. P. gulae is considered the main pathogen involved in periodontal disease in dogs. However, the characteristics of the VSCs produced by P. gulae are unknown. In the present study, VSCs were measured in 26 isolates of P. gulae and some isolates of the other Porphyromonas spp. obtained from the oral cavities of dogs with periodontal disease using an in vitro assay with an Oral ChromaTM gas chromatograph. The results demonstrated that P. gulae was able to produce large amounts of H2S and CH3SH, and the dominant one was CH3SH (CH3SH/H2S was approximately 2.2). Other Porphyromonas spp. that were also obtained from the oral cavities of dogs with periodontal disease indicated the similar levels of production of H2S and CH3SH to those of P. gulae. It is strongly suggested that the high levels of H2S and CH3SH in P. gulae and other Porphyromonas spp. contribute to halitosis and the destruction of periodontal tissues during the progression of periodontal disease in dogs.

Lithium-sulfur (Li-S) battery has been regarded as an important candidate for the next-generation energy storage system due to its high theoretical capacity (1675 mAh g-1) and high energy density (2600 Wh kg-1). However, the shuttle effect of polysulfide seriously affects the cycling stability of the Li-S battery. Here, a novel Fe3C decorated folic acid-derived graphene-like N-doped carbon sheet (Fe3C@N-CS) was successfully prepared as the polysulfide catalyst to modify the separator of Li-S battery. The porous layered structures can successfully capture polysulfide as a physical barrier, and the encapsulated Fe3C catalyst can effectively trap and catalyze the conversion of polysulfide, thus accelerating the redox reaction kinetics. Together with the highly conductive networks, the cell with Fe3C@N-CS modified separator evinces superior cycling stability with 0.06% capacity decay per cycle at 1 C rate over 500 cycles and excellent specific capacity with an initial capacity of 1260 mAh g-1 at 0.2 C. Besides, at a high sulfur loading of 4.0 mg cm-2, the batteries also express superb cycle stability and rate performance.

In this study, an improved UPLC-MS method for simultaneously quantifying twelve major components belonging to two chemical types was developed and validated, and was applied to quantitatively compare the quality of Astragali Radix sulfur-fumigated with different durations and the fresh reference sample. The results showed that the contents of triterpenes Astragaloside III and Astragaloside IV decreased moderately, while the flavonoids calycosin, formononetin, and 7,2'-dihydroxy-3',4'-dimethoxyisoflavane decreased significantly, and its corresponding flavonoid glycosides increased accordingly, which indicatied that the happening of chemical transformation of flavonoids and glycosides in the sulfur-fumigated process. These transformations were further confirmed by the the synthesis of flavonoid glycosides under the simulated sulphur-fumigation circumstances. Furthermore, the sulfur-fumigated duration had a proportional relationship with the contents of compounds 7, 11, and 12. All these results suggested that the established method was precise, accurate and sensitive enough for the global quality evaluation of sulfur-fumigated Astragali Radix, and sulfur-fumigation can not only change the proportions of bioactive components, but also cause the chemical transformation in the Astragali Radix.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Various kinds of primary metabolisms in plants are modulated through sulfate assimilation that the uptake of this inorganic compound can be regulated via the sulfate transporters, such as sulfotransfer-ases (SOTs), engaged in the sulfur metabolism. In the current study a genome-wide approach has been utilized for recognition and characterization of SOT family genes in the significant nutritional crop po-tato (Solanum tuberosum L.). As a result, 29 StSOT genes were identified in the potato genome, which were mapped onto the nine S. tuberosum chromosomes. The protein motifs structure demonstrated two highly conserved 5' PSB region and 3' PB motif that are essential for sulfotransferase and catalytic ac-tivities. The protein-protein interaction networks also significantly demonstrated an interesting collabo-ration between SOTs and the other genes, such as PRTase, APS-kinase, protein phosphatase and APRs, in sulfur compounds biosynthesis and regulation of the flavonoid and brassinosteroid metabolic pro-cesses, which clearly detected the importance of sulfotransferases for potato proper growth/development and stress dealing. Notably, the homology modeling of StSOT proteins and dock-ing analysis of their ligand-binding sites revealed the presence of some stress-responsive residues, such as proline, glycine, serine and lysine, in their active sites. The expression assay of StSOT genes via the potato RNA-seq data clearly suggested the engagements of these gene family members in plants growth and extension as well as responses to various hormones and biotic/abiotic stimulus circum-stances. Our predictions can be informative for the functional characterization of the SOT genes in po-tato and may the other nutritional crops.

Stable-isotope dimethyl labeling is a highly reactive and cost-effective derivatization procedure that could be utilized in proteomics analysis. In this study, a liquid chromatography-tandem mass spectrometry in multiple reaction monitoring mode (LC-MS-MRM) platform for the quantification of kiwi allergens was first developed using this strategy. Three signature peptides for target allergens Act d 1, Act d 5, and Act d 11 were determined and were derivatized with normal and deuterated formaldehyde as external calibrants and internal standards, respectively. The results showed that sample preparation with the phenol method provided comprehensive protein populations. Recoveries at four different levels ranging from 72.5–109.3% were achieved for the H-labeled signature peptides of Act d 1 (SPA1-H) and Act d 5 (SPA5-H) with precision ranging from 1.86–9.92%. The limit of quantification (LOQ) was set at 8 pg mL–1 for SPA1-H and at 4 ng mL–1 for SPA5-H. The developed procedure was utilized to analyze seven kinds of hand-made kiwi foods containing 0.0175–0.0515 mg g–1 of Act d 1 and 0.0252–0.0556 mg g–1 of Act d 5. This study extended the applicability of stable-isotope dimethyl labeling to the economical and precise determination of food allergens and peptides.

Stable isotope-assisted approaches can improve untargeted LC-HRMS metabolomics studies. Here, we demonstrate at the example of chemically stressed wheat that metabolome-wide internal standardization by globally 13C-labeled metabolite extract (GLMe-IS) of experimental-condition-matched biological samples can help to improve coverage of treatment-relevant metabolites and aid in the post-acquisition assessment of putative matrix effects in samples obtained upon different treatments. For this, native extracts of toxin- and mock-treated (control) wheat ears were standardized by the addition of uniformly-13C-labeled wheat ear extracts that were cultivated under similar experimental conditions (toxin-treatment and control) and measured with LC-HRMS. The results show that 996 wheat-derived metabolites were detected with the non-condition-matched 13C-labeled metabolite extract, while another 68 were only covered by the experimental-condition-matched GLMe-IS. Additional testing is performed with the assumption that GLMe-IS enables compensation for matrix effects. Although on average no severe matrix differences between both experimental conditions were found, individual metabolites may be affected as is demonstrated by wrong decisions with respect to the classification of significantly altered metabolites. When GLMe-IS was applied to compensate for matrix effects, 272 metabolites showed significantly altered levels between treated and control samples, 42 of which would not have been classified as such without GLMe-IS.

The current work aimed to screen the ruminal cyanide-utilizing bacteria and evaluate the influence of fresh cassava root (FCR) and pellets containing high sulfur (PELFUR) on cyanide content, kinetics of gas, in vitro degradability, and ruminal fermentation. The experiment was conducted in a Completely randomized design (CRD) for a screening of cyanide-utilizing bacteria and the dietary treatments were the level of cyanide at 0, 150, 300, and 450 ppm. A 5 × 3 factorial arrangement in a Completely randomized design was used for in vitro study. Factor A was the level of FCR at 0, 260, 350, 440, and 530 g/kg of 0.5 g dry matter (DM) substrate, and factor B was the level of PELFUR at 0, 15, and 30 g/kg DM substrate. Adding different doses of cyanide significantly affected cyanide-utilizing rumen bacterial growth (p < 0.05). Increasing the concentration of cyanide from 0 to 150 and 150 to 300 ppm, resulted in an increase in cyanide-utilizing rumen bacteria of 38.2% and 15.0%, respectively. Increasing the FCR level to more than 260 g/kg of 0.5 g substrate could increase cumulative gas production (p < 0.05), whereas increasing doses of PELFUR from 15 to 30 g/kg increased the cumulative gas production when compared with that of 0 g/kg PELFUR (p < 0.05). Cyanide concentration in rumen fluid decreased with PELFUR (p < 0.05) supplementation. Degradability of in vitro dry matter and organic matter following incubation increased at 12 and 24 h due to PELFUR supplementation with FCR and increased additionally with 15 g/kg PELFUR (p < 0.05) in 440 g/kg FCR. Proportions of the total volatile fatty acids, acetic acid (C2), propionic acid (C3), and butyric acid, as well as the ratio of C2 to C3 among supplementations with FCR (p < 0.05) were significantly different. As the proportion of FCR increased to 530 g/kg of the substrate, the volume of C3 increased by 14.6%. This is the first finding of bacteria in the rumen capable of utilizing cyanide, and cyanide might function as a nitrogen source for bacterial cell synthesis. Inclusion of FCR of 530 g/kg with 30 g/kg PELFUR could increase the cumulative gas production, the bacterial population, the in vitro degradability, the proportion of C3, and the rate of the disappearance of cyanide.

Sulfur contamination of topsoil, spatial distribution of contamination and surface water chemistry were investigated on an area of over 200 ha of a new forest ecosystem. Common birch and Scots pine growth reaction, vitality and nutrients supply, as well as wood small-reed (Calamagrostis epigejos (L.) Roth) chemical composition were assayed. The chemistry dynamics of soil leaching and the sulfur load leached from the sulfur contaminated soil-substrates were analyzed. The remediation effect of the birch and pine litter was assayed in an experiment under controlled conditions. It was found that reclamation was effective in a majority of the post-mining site, however hot-spots with sulfur contamination reaching even 45,000 mg kg-1, pH <2.0, and EC 6,500 µS cm-1 were reported. Surface waters typically displayed elevated concentrations of sulfate ions (average 935.13 mg L-1), calcium ions (up to 434 mg L-1) and high EC (average 1.795 µS cm-1), which was connected both with sulfur contamination and sludge lime used in neutralization. Wood small-reed was found to be species adapting well to the conditions of elevated soil salinity and sulfur concentration. We noted that an addition of organic matter had a significant impact on the chemistry of soil solutions but did not indicate in short term experiment a remediation effect by increased sulfur leaching.

In this paper, the performance of Cu-(In,Ga)-S2 (CIGS2) solar cells with adjusting composite CGI-ratio absorber is explored and compared through an improved three-stage co-evaporation technique. For co-evaporating CIGS2 absorber as a less toxic alternative to Cd-containing film, we analyse the effect of the CGI-ratio stoichiometry and crystallinity, and explore its opto-electric sensing characteristic of individual solar cell. The results of this research signify the potential of high-performance CIGS2-absorption solar cells for photovoltaic (PV)-module industrial applications. For the optimal CIGS2-absorption film (CGI=0.95), the Raman main-phase signal (A1) falls at 291 cm-1, which is excited by the 532-nm line of Ar+-laser. Using photo-luminescence (PL) spectroscopy, the corresponding main-peak bandgaps measured is 1.59 eV at the same CGI-ratio film. Meanwhile, the best conversion efficiency (=3.212%) and the average external quantum efficiency (EQE=51.1% in the visible-wavelength region) of photo-electric properties were achieved for the developed CIGS2-solar cells (CGI=0.95). The discoveries of this CIGS2-absorption PV research provide a new scientific understanding of solar cells. Moreover, this research undeniably contributes to a major advancement towards practical PV-module applications and can help more to build an eco-friendly community.

Various types of electroconductive additives were evaluated for high C-rate capability in an attempt to extend practical application of high-areal-capacity lithium–sulfur batteries that employ an aluminum-foam current collector. Carbon nanofibers (CNFs) were found to be the most effective additive, with the ability to attain a high-sulfur-loading of 40 mg cm−2. A CNF-containing cell exhibited gravimetric capacities of 1094 and 758 mAh gsulfur−1 (46.8 and 32.4 mAh cm−2) at 0.05 and 0.1 C-rate, respectively, in an ether-based electrolyte. Because a CNF-containing slurry exhibits low viscosity even at a high solid ratio, it could be filled into the aluminum foam. Additionally, a lithium–sulfur battery with high-sulfur-loading had an energy density of ~120 Wh kg−1, a value that was calculated from the weight of the components of the cathode, anode, current collectors, electrolyte, and separator. Assuming that the amount of electrolyte decreases and that the energy density of cells accumulate, a theoretical energy density of 522 Wh kg−1 was estimated. Moreover, it was found that even if a high-areal-capacity was achieved, the discharge capacity converged at a high C-rate, unless there was an improvement in ion diffusion in the bulk electrolyte. This is considered a limitation of sulfur cathodes with high-sulfur-loading.

This study examined the spatial-temporal distribution of sulfur and iron compounds (dissolved sulfide, iron sulfide, and ionized iron) in sediments from April 2015 to March 2016 at four stations in Mikawa Bay, Japan. Seasonal changes were observed in dissolved sulfide, iron sulfide, and ionized iron in the upper part of the sediment (0–4 cm depth) at all stations. The maximum concentration in the upper part of the central bay was 2.8 mmol L-1. The maximum values of dissolved sulfide (ranging from 1.4 to 8.1 mmol L-1) at stations located in a water way varied among stations. The iron sulfide concentration in the upper part of the sediment at a station where dissolved sulfide concentration in the waterway was relatively low exceeded that at other stations in the waterway during spring to summer. Ionized iron concentration was highest at the station where the dissolved sulfide concentration was low. The study results suggest that iron plays an important role in determining the magnitude of dissolved sulfide accumulation in sediments by binding with dissolved sulfide. The results imply the possibility of mitigating the accumulation of free sulfides, which causes extreme hypoxia, by artificially adding sufficient iron to the seabed.

Ceria, zirconia and mixed cerium-zirconium mesoporous oxides were synthesized and used as supports for sulfur and gold species. The materials were characterised using selected advanced techniques (ICP-OES, elemental analysis, XPS, XRD, N₂ adsorption and desorption isotherms, UV-vis, ATR-FTIR, TPR-H₂, TG-DTA) which allowed monitoring of the oxidation state of metals (cerium and gold) and the surface properties of the catalysts, in particular the concentration of the components on the surface and in the bulk of materials. The interactions between gold, sulfur and metals from oxides were considered. The goal of this work was studied the changes in the chemical composition of materials and the oxidation states of cerium species after the modification of oxides with sulfur and gold species and the estimation of the influence of these changes on the surface properties. The chemical composition of surface affects the mobility of surface oxygen and the oxidation state of cerium, which can play the role of redox sites (e.g. Ce³⁺/Ce⁴⁺ species), and therefore it strongly influences on the adsorption of hydrogen sulfide and then gold loading. Additionally, gold catalysts modified with sulfur species were tested in the reaction of glycerol oxidation in the liquid phase at basic conditions as the test reaction of the catalytic oxidation of organic pollutants from water.

The Sanhetun tellurium-gold (Te-Au) deposit, located in the Duobaoshan polymetallic metallogenic belt (DPMB) within the eastern section of the Central Asian Orogenic Belt (CAOB), is a newly discovered small scale gold deposit. The mineralization, with resource of ≥ 4t Au, is mainly hosted in 3 NNE-trending alteration zones between granitic mylonite and volcanogenic-sedimentary formations. It’s the genesis and timing of formation of this deposit are poorly constrained. Here, we report the results of petrographic studies, TESCAN Integrated Mineral Analyzer (TIMA), major and trace element concentrations, and in situ S isotope of pyrite and U-Pb ages of calcite. The results show that there are five species of telluride, including native tellurium, tetradymite, tsumoite, hessite and petzite and four types of pyrite, including coarse-grained euhedral Py1, fine-grained quartz-Py2 vein crosscutting Py1 and anhedral aggregated Py3 and Py4. The pre-ore Py1, containing negligible Au, Te and other trace elements, have a relatively narrow range of δ34S values ranging from -1.20 to -0.57‰. The Py2 have slightly high concentrations of Au and Te and distinctly high concentrations of Mo, Sb, Zn and Mn with markedly positive δ34S values of 4.67 to 14.43‰. The main ore stage Py3 contains high Au and Te concentrations and shows narrow δ34S values ranging from -5.69 to 0.19‰. The post-ore stage Py4 contains low Au concentrations with the δ34S values ranging from 2.66 to 3.86‰. Calcite from ore stage yield a U-Pb age of 135 ± 22 Ma, interpreted as the age of Te-Au mineralization. Our geochemical and geochronological data indicate that the Te was derived from partial melting of mantle metasomatized by the Te-rich fluids that originated from oceanic sediments. We correlate the tectonic setting with the subduction of Paleo Pacific plate in Early Cretaceous.

The sulfur-containing amino acids methionine (Met), cysteine (Cys) and taurine (Tau) are common dietary constituents with important cellular roles. Met restriction is already known to exert in vivo anticancer activity. However, since Met is a precursor of Cys, and Cys produces Tau, the role of Cys and Tau in the anticancer activity of Met-restricted diets is poorly understood. In this work, we screened the in vivo anticancer activity of several Met-deficient artificial diets supplemented with Cys, Tau or both. Diet B1 (6% casein, 2.5% leucine, 0.2% Cys and 1% lipids) and diet B2B (6% casein, 5% glutamine, 2.5% leucine, 0.2% Tau and 1% lipids) showed the highest activity and were selected for further studies. Both diets induced a marked anticancer activity in two animal models of metastatic colon cancer, which were established by injecting CT26.WT murine colon cancer cells in the tail vein or peritoneum of immunocompetent BALB/cAnNRj mice. Diets B1 and B2B also increased the survival of mice with disseminated ovarian cancer (intraperitoneal ID8 Tp53 -/- cells in C57BL/6JRj mice) and renal cell carcinoma (intraperitoneal Renca cells in BALB/cAnNRj mice). The high activity of diet B1 in mice with metastatic colon cancer may be useful in colon cancer therapy.

Methane fermentation of organic waste is one way to minimize organic waste, which accounts for 77% of the global municipal waste stream. The use of biowaste treatment technologies helps to improve the energy independence of the regions. Improving the efficiency of the methane fermentation process by using additives from waste may be an attractive alternative to the original technology. The use of biochar as an additive for methane fermentation has been shown to increase the production potential of biogas. The reasons for the improvement in efficiency are complex among others, it is assumed that the specific surface area of ​​biochar may increase the population of anaerobic organisms. Up to date, there are many researches on the effect of biochar additions on methane fermentation, but there is no research on the effect of sulfur-biochar composite. The composite product in the form of a mixture of biochar and molten sulfur is an interesting area of ​​research. In this experiment additions of the sulfur-biochar composite were tested to improve the fermentation process. The composite consisted of 40% biochar and 60% of sulfur and was added to the process. As results the addition of 1% of the composite increased the biogas potential by 4%.

Many studies of hypervelocity impact craters have described the characteristics of quartz grains shock-metamorphosed at high pressures of > 10 GPa. In contrast, few studies have investigated shock metamorphism at lower shock pressures. In this study, we test the hypothesis that low-pressure shock metamorphism occurs in near-surface nuclear airbursts and that this process shares essential characteristics with crater-forming impact events. To investigate low-grade shock microstructures, we compared quartz grains from Meteor Crater, a 1.2-km-wide impact crater, to those from near-surface nuclear airbursts at the Alamogordo Bombing Range, New Mexico in 1945 and Kazakhstan in 1949/1953. This investigation utilized a comprehensive analytical suite of high-resolution techniques, including transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD). Meteor Crater and the nuclear test sites all exhibit quartz grains with closely-spaced, sub-micron-wide fractures that appear to have formed at low shock pressures. Significantly, these micro-fractures are closely associated with Dauphiné twins and are filled with amorphous silica (glass), widely considered a classic indicator of shock metamorphism. Thus, this study confirms that glass-filled shock fractures in quartz form during near-surface nuclear airbursts, as well as crater-forming impact events, and by extension, it suggests that they may form in any near-surface cosmic airbursts in which the shockwave is coupled to Earth’s surface. The robust characterization of such events is crucial because of their potential catastrophic effects on the Earth’s environmental and biotic systems.

Many studies of hypervelocity impact craters have described the characteristics of quartz grains shock-metamorphosed at high pressures of >10 GPa, but in contrast, few studies have investigated shock metamorphism at lower shock pressures. In this study, we test the hypothesis that low-pressure shock metamorphism occurs in near-surface nuclear airbursts and that this process shares important characteristics with impact-cratering events. To investigate low-grade shock microstructures, we compared quartz grains from Meteor Crater, a 1.2-km-wide impact crater, to those from near-surface nuclear airbursts at the Alamogordo Bombing Range, New Mexico in 1945 and Kazakhstan in 1949/1953. This investigation utilized a comprehensive analytical suite of high-resolution techniques, including transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD). Meteor Crater and the nuclear test sites all exhibit metamorphosed quartz grains with closely-spaced, sub-micron-wide fractures that appear to have formed at low shock pressures. Importantly, these micro-fractures are closely associated with Dauphiné twins and are filled with amorphous silica (glass), widely considered to be a classic indicator of shock metamorphism. Thus, this study confirms that glass-filled shock fractures in quartz form during near-surface nuclear airbursts, as well as crater-forming impact events, and by extension, it suggests they also may form in near-surface cosmic airbursts.

In the present study, the potential of ethylene as ethephon (an ethylene source) was investigated individually or with a combination of the split dosage of nitrogen (N) and sulfur (S) soil treatments for the removal of damaging effects of salt stress (100 mM NaCl) in mustard (Brassica juncea L.). Plants were grown with 50 mg N plus 50 mg S kg−1 soil at sowing time and an equivalent dosage at 20 days after sowing ([N50 + S50]0d + [N50 + S50]20d). Ethephon at 200 μL L‒1 was applied to combined split dosage of N and S with or without NaCl. Plants subjected to NaCl showed a deceased in growth and photosynthetic characteristics as well as N and S assimilation, though, proline metabolism and antioxidants increased. The application of ethephon to plants grown with split N and S dosages significantly enhanced the photosynthetic efficiency by increasing the assimilation of N and S, improving the content of proline and induction of the antioxidant system with or without NaCl. The regulation of ethylene and/or split form N and S application may be the potential tools for overcoming salt stress effects in this species and in related Brassicaceae.

Studies of dietary preferences of migratory species are of great importance as these species connect food webs of habitats across the migration route and thus represent trophic relationships between the spatially disjointed communities. Here we describe dietary preferences of threespine stickleback G. aculeatus in the White Sea during the spawning season using stable isotope and stomach content analyses. Both analyses indicated that during the spawning season, when sticklebacks spend most of the time in the inshore, their diet significantly consist of benthic species in contrast to the start of the spawning season when fishes migrating from the offshore are feeding on zooplankton. Also, we show that stickleback eggs contribute greatly to the diet of both male and female fishes. Using Bayesian mixing modelling we show that dietary preferences in females were broader than in males, and more variable during the spawning season. Males fed on eggs almost while guarding their nests. Both stomach contents and isotope signatures demonstrate that by the end of the spawning season sticklebacks again increase consumption of plankton, and isotope analysis proved to be more reliable tool to trace this change than stomach content analysis. Our results show that stable isotope and stomach content analyses well supplement each other in understanding of seasonal changes in dietary composition of stickleback.

A series of precise data consisting of zircon U–Pb ages, whole-rock geochemistry and Sr–Nd–Hf isotope compositions from the Huhetaoergai granitic pluton was collected in this study and combined with data from the western Huhetaoergai, Zhuxiaogubuhe and Yagan granitic plutons to constrain the petrogenesis and tectonic setting of granitic plutons in the northern Ya-Gan fault zone, North Alxa, China. The Huhetaoergai pluton is composed of hornblende diorite, medium- to coarse-grained biotite adamellite and coarse-grained biotite adamellite with K-feldspar megacrysts. The U–Pb zircon ages of biotite adamellite are 220.5 ± 1.9 Ma and 226.5 ± 2.4 Ma. These granitoids are I-type granites with highly radiogenic initial ⁸⁷Sr/⁸⁶Sr of 0.708085–0.735470, negative eNd(t) average values of −2.98–3.23 and high eHf(t) of 9–11.05. These features indicate the granitoids were formed from magmas generated from juvenile crust. We speculate that the granitoids of the Huhetaoergai pluton were emplaced during an episode of intense intraplate orogenic movement evolution in an extrusional setting after a period of extensional postcollisional intraplate evolution.

The corrosion inhibition performance of pyridine derivatives (4-methylpyridine and its quaternary ammonium salts) and sulfur-containing compounds (thiourea and mercaptoethanol) with different molar ratios on carbon steel in CO2-saturated 3.5 wt.% NaCl solution was investigated by weight loss, potentiodynamic polarization, electrochemical impedance spectroscopy and scanning electron microscopy. The synergistic corrosion inhibition mechanism of mixed inhibitors was elucidated by the theoretical calculation and simulation. The molecule of pyridine derivatives compound with larger volume has the priority to adsorb on the metal surface, while the molecules of sulfur-containing compounds with smaller volume fill in vacancies. A dense adsorption film would be formed when 4-PQ and sulfur-containing compounds are added at a proper mole ratio.

The objective of this experiment was to study the effect of feeding pellet containing high sulfur (PELFUR) diet and fresh cassava root (FCR) to Thai native beef cattle on feed use efficiency, ruminal characteristics, and blood metabolites. Four male Thai native beef cattle (150 ± 15.0 kg of body weight (BW)) were allocated with a 2 × 2 factorial arrangement in a 4 × 4 Latin square design. Factor A was FCR supplementation at 15 and 20 g/kg of BW. Factor B was the sulfur level in the PELFUR ration at 15 and 30 g/kg of dry matter (DM). No interaction effect was found among FCR supplementation and PELFUR in terms of feed intake and nutrient intake (p > 0.05). Cyanide intake was significantly increased based on FCR supplementation (p < 0.05), whereas sulfur intake was increased by level addition of PELFUR levels (p < 0.05). There were interaction effects among FCR supplementation and PELFUR on digestibility coefficients of DM and organic matter (OM) (p < 0.05). FCR supplementation at 20 g/kg BW with PELFUR 30 g/kg demonstrated the highest digestibility of DM and OM. Moreover, interactions were observed between FCR and PELFUR for bacterial populations (p < 0.01). The populations of bacteria were highest in FCR supplementation at 20 g/kg BW with PELFUR 30 g/kg at various feeding times. An interaction effects from among feeding FCR with PELFUR was found on blood thiocyanate concentrations at various feeding times (p < 0.01). The highest mean values of blood thiocyanate were observed when feeding FCR at 20 g/kg BW with PELFUR at 30 g/kg. No interaction effect was found between FCR and PELFUR on total volatile fatty acids (VFA) and their profiles (p >0.05). However, the proportions of the total VFA at 0 and 4 h post-feeding were increased when FCR at 20 g/kg BW was supplemented (p < 0.01). FCR at 20 g/kg BW could enhance propionate (C3) at 4 h post-feeding when compared with FCR at 15 g/kg BW (p < 0.01). Moreover, supplementation of PELFUR at 30 g/kg increased the total VFA at 0 and 4 h post-feeding, whereas the concentration of C3 at 4 h post-feeding was enhanced (p < 0.05). However, no significant changes were found for any parameters among treatments and between the main effect of FCR and PELFUR supplementation (p > 0.05). In conclusion, feeding of two combinations (FCR 20 g/kg BW with PELFUR 30 g/kg) could promote the nutrient digestibility, the bacterial populations, and the rate of disappearance of cyanide without having any adverse effect on rumen fermentation.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.