In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

The study investigated farmers’ perception on pests and diseases management strategies, agricultural practices, production constraints and selection criteria of elite varieties using a survey research design. A total of 700 questionnaires were administered to smallholder farmers who were farming for household consumption, those producing for sale and household consumption and those who were mainly producing for sale because their primary goal was to produce for the market. Findings revealed that the most prevalent pests identified were whiteflies (Bemisia tabaci), grasshoppers (Zonocerus variegatus), aphids (Aphis gossypii), mealybugs (Phenacoccus manihoti), termites (Isoptera), and grasscutters (Thryonomys swinderianus). The three most common diseases of cassava limiting growth and yield with mixed infection include viral, bacterial, and fungal. The study also revealed that only 12.5% of farmers cultivated improved cassava varieties. The management practices implemented encompassed field sanitation and the application of pesticides. Lack of capital and no availability of market were the most important production and marketing constraints faced by farmers in the study area, whereas poundability and high storage root yield are the most preferred traits farmers consider in selecting a new variety. Results suggest that smallholder farmers should endeavor to undergo various developmental programs to develop themselves to increase their competitive advantage in their locality and in the local and global agricultural sectors. In addition, governments and other policy makers should strategize plans and programs that would contribute to smallholder farmers’ agriculture, community and national development.

We present a surface acoustic wave (SAW) sensor array for microRNA (miRNA) detection that utilizes photocatalytic silver staining on titanium dioxide (TiO2) nanoparticles as a signal enhancement technique for high sensitivity with an internal reference sensor for high reproducibility. A sandwich hybridization was performed on working sensors of the SAW sensor array that could simultaneously capture and detect three miRNAs (miRNA-21, miRNA-106b, and miRNA-155) known to be upregulated in cancer. Sensor responses due to signal amplification varied depending on the concentration of synthetic miRNAs. It was confirmed that normalization (a ratio of working sensor response to reference sensor response) screened out background interferences by manipulating data and minimized non-uniformity in the photocatalytic silver staining step by suppressing disturbances to both working sensor signal and reference sensor signal. Finally, we were able to successfully detect target miRNAs in cancer cell-derived exosomal miRNAs with performance comparable to the detection of synthetic miRNAs.

The subject of the research is to Development of laser ablation method for Fabrication of surface acoustic wave sensors on quartz wafer, the target of the GQW – is to design Acoustic wave sensor by using laser ablation method. By using the surface acoustic wave theory to sense by the signal and using this physical phenomenon, We will design the sensor which transduce an input electrical signal into a mechanical wave which unlike an electrical signal, can be easily influenced by physical phenomena. The device then transducers this wave back into an electrical signal on the secondary terminal of the sensor. Changes in amplitude, phase, frequency, or time-delay between the input and output electrical signals can be used to measure the presence of the desired Our work in this part, especially the practical part like temperature, vibration ,etc. we design a combs on the waver of quartz to make like an electrode primary electrode & secondary electrode by putting coats of cuppers & vanadium on the waver and then using the fiber optic laser regime to design this combs to can able transfer the signal by ablation the most important here to use the regime of fiber optic laser then we using this sensor in any electronic circuit How we will select the suitable kind of laser to design, this is the most important part, and what it will be the diameter of that combs of secondary and primary , how much the value of the wave length to select the micro distant combs to avoid any inductance and interference for transferred signal , also take the benefit of using MEMS theory in our project.

Dearth of information on extent of genetic variability in cassava limits the genetic improvement of cassava in Sierra Leone. This study aimed at assessing the genetic variability and relationships within 103 cassava genotypes using agro-morphological and culinary markers. A field trial was conducted in the School of Agriculture and Food Sciences research site. The experiment was laid in an augmented randomized block design. Morphological classification based on qualitative and quantitative traits categorized the germplasm into three different groups. A total of ten principal components (PCs) in the qualitative and six PCs in the quantitative trait sets accounted for 66.74% and 67.27% of the total genetic variation, respectively. Traits with significantly strong and positive correlations included presence of fruit (PFRT) and presence of seed (PSE)(r = 0.86***),root yield per plant (RYPP) and number of storage root (NSR) (r = 0.76***), RYPP and number of commercial root (NCR) (r = 0.68***), length of leaf lobe (LLL) and width of leaf lobe (WLL) (r = 0.66***),and between NSR and NCR (0.84***). Cooking time, cooking percentage, texture, mealiness, taste and aroma varied widely among the accessions. Findings established that the cassava germplasm possess useful genetic variability that could be exploited through selection for short term release programme, genetic conservation of valuable germplasm and genetic improvement of the crop.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

Almost 50 papers on surface plasmon resonance biosensors, published between 2016 and mid-2018, are reviewed. Papers concerning the determination of large particles such as vesicles, exosomes, cancer cells, living cells, stem cells and microRNA are excluded, as these are covered by a very recent review. The reviewed papers are categorized into five groups, depending on the degree of maturity of the reported solution: ranging from simple marker detection to clinical application of a previously developed biosensor. Instrumental solutions and details of biosensor construction are analyzed, including the chips, receptors and linkers used, as well as calibration strategies. Biosensors with a sandwich structure containing different nanoparticles are considered separately, as are SPR applications for investigating the interactions of biomolecules. An analysis is also made of the markers determined using the biosensors. Concluding, there is shown to be a growing number of SPR applications in the solution of real clinical problems.

Biosensors detect specific bio-analytes by generating a measurable signal from the interaction between the sensing element and the target molecule. Surface acoustic wave (SAW) biosensors offer unique advantages due to their high sensitivity, real-time response capability, and label-free detection. The typical SAW modes are the Rayleigh mode and the shear-horizontal mode. Both present pros and cons for biosensing applications and generally need different substrates and device geometries to be efficiently generated. This study investigates and characterizes ultra-high-frequency (UHF-) SAW resonator biosensors. It reveals the simultaneous presence of the two typical SAW modes, clearly separated in frequency, called slow and fast. The two modes are studied by numerical simulations and biosensing experiments with the glial-fibrillary-acidic-protein (GFAP) biomarker. The slow mode is generally more sensitive to changes in surface properties, such as temperature and mass changes, by a factor of about 1.4 with respect to the fast mode.

Frequency combs (FCs)—spectra containing equidistant coherent peaks—have enabled researchers and engineers to measure the frequencies of complex signals with high precision thereby revolutionising the areas of sensing, metrology and communications and also benefiting the fundamental science. Although mostly optical FCs have found widespread applications thus far, in general FCs can be generated using waves other than light. Here, we review and summarise recent achievements in the emergent field of acoustic frequency combs (AFCs) including phononic FCs and relevant acousto-optical, Brillouin light scattering and Faraday wave-based techniques that have enabled the development of phonon lasers, quantum computers and advanced vibration sensors. In particular, our discussion is centred around potential applications of AFCs in precision measurements in various physical, chemical and biological systems in conditions, where using light, and hence optical FCs, faces technical and fundamental limitations, which is, for example, the case in underwater distance measurements and biomedical imaging applications. This review article will also be of interest to readers seeking a discussion of specific theoretical aspects of different classes of AFCs. To that end, we support the mainstream discussion by the results of our original analysis and numerical simulations that can be used to design the spectra of AFCs generated using oscillations of gas bubbles in liquids, vibrations of liquid drops and plasmonic enhancement of Brillouin light scattering in metal nanostructures. We also discuss the application of non-toxic room-temperature liquid-metal alloys in the field of AFC generation.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

It is well-known that surface plasmon wave propagates along a straight line, but this common sense was broken by the artificial curved light – plasmon Airy beam. In this paper, we introduce a new class of curved surface plasmon wave - the photonic hook plasmon. It propagates along wavelength scaled curved trajectory with radius less than surface plasmon polariton wavelength, and can exist despite the strong energy dissipation at the metal surface.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

Genetic diversity is very important in crop improvement. This study was carried out to assess the genetic diversity and the number of unique multilocus genotypes (MLGs) in cassava collection in Burkina Faso. To achieve this objective 130 cassava accessions were genotyped using 32 simple sequence repeat (SSR) markers. The results revealed that among these markers, twelve (12) were highly informative, with the PIC values greater than 0.50, twelve (12) were moderately informative, with the PIC values ranged between 0.25 and 0.50, and eight (8) were not very informative, with the PIC values lower than 0.25. A moderate level of genetic diversity was found for the population, indicated by the average expected heterozygosity (0.45) and the observed heterozygosity (0.48). About 83.8% of unique multilocus genotypes were found in the cassava collection indicating that SSR markers seem to be most appropriate for MLGs identification. Population structure analysis based on hierarchical clustering identified two subpopulations and Bayesian approach suggested five clusters. Additionally, DAPC analysis separated the cassava accessions into 13 subpopulations. The comparison of these results and the previous study using SNP, suggest that each type of markers can be used to assessment the genetic structure of cassava grown in Burkina Faso.

Irrigation is a useful crop enhancement procedure up to the point where free surface water appears. Thereafter, water can begin to flow into waterways, leaching nutrients and giving rise to environmental damage, as well as being a waste of a precious resource. The current work addresses the problem of measuring free water on the surface of agricultural soils by a real-time acoustic remote sensing method. Directional acoustic transmitter and receiver arrays are used to define a ‘footprint’ on the ground from which changes in reflectance are sensed. These arrays are mounted on a moving irrigator. Chirp signals are used to provide along-path resolution and to ensure robustness against unwanted acoustic background noise from farm machinery and the irrigator. Field measurements have been conducted above a well-defined ‘quadrat’ with controlled and measured water content, and also with the instrument mounted on an operational irrigator. A structured light camera mounted above the footprint is used to validate surface water fraction. It is found that the areal fraction of free water on the soil surface can be reliably estimated from changes in the amplitude of the reflected sound waves. The mechanism giving rise to the observed acoustic reflectivity changes is discussed and a model is developed which agrees with normalized intensity observations with a coefficient of determination R2 between 0.65 and 0.83. The rms error between model predictions and observations is comparable to the rms variation of the measurements, indicating that there is insignificant error due to the choice of model.

German noise action plans aim to reduce negative health outcomes from noise exposure and identify quiet areas free of noise pollution. Quiet area identification in German noise action plans is based primarily on noise mapping and spatial analysis and not empirical or qualitative data about acoustic environments, thus leaving a gap in the understanding of the quality of formally recognized quiet areas in noise action plans. This work presents a comparative empirical case study in Dortmund, Germany, with the aim to describe the diurnal dB(A) and biophonic properties of quiet areas versus noise 'hot spots'. Sound observations were collected (n=282,764) in five different natural or recreational land use patch types larger than four acres within 33 proposed quiet areas in Dortmund (n=70) and 23 noise hot spots between April 27^th, 2022 and March 2^nd, 2023. We find that quiet areas are on average more than 20 dB(A) quieter than noise hot spots almost every hour of the day. Forests, managed tree stands, cemeteries, and agriculture diel patterns are dominated by dawn dusk chorus in spring and summer, whereas sport and recreation as well as noise hot spots are dominated by traffic and human noise. A novel composite biophony mapping procedure is presented that finds distinct temporal distribution of biophony in forested and agriculture peri-urban locations positively associated with patch size, distance away from LDEN > 55, proximity to water, and the number of vegetation layers in the plant community. Anthrophony distribution dominates urban land uses in all hours of the day, but expands during day and evening and contracts at night and in dusk hours. The procedures presented here illustrate how qualitative information regarding quiet areas can be integrated into German noise action planning.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

Extraction of high-resolution surface waves is essential in surface-wave survey. Because reflections usually interfere with surface waves on X component in a multicomponent seismic exploration, it is difficult to extract dispersion curves of surface waves. The situation goes more serious when the frequencies and velocities of higher-mode surface waves are close to those of PS-waves. A method for surface-wave extraction is proposed based on the morphological differences between reflections and surface waves. Frequency-domain high-resolution linear Radon transform (LRT) and time-domain high-resolution hyperbolic Radon transform (HRT) are used to represent surface waves and reflections respectively. Then, the sparse representation problem based on the morphological component analysis (MCA) is built and optimally solved to obtain high-fidelity surface waves. An advantage of our method is its ability to extract surface waves when their frequencies and velocities are close to those of reflections. Furthermore, results of synthetic and field examples confirm that the proposed method can attenuate the distortion of surface-wave dispersive energy caused by reflections, which contributes to extracting accurate dispersion curves.

A tunable near-infrared surface plasmon resonance (SPR) biosensor based on gate-controlled graphene plasmons is investigated theoretically. The novel characteristics of chemical potential sensing make the proposed sensor promising in the application of ultra-sensitive and highly specific biosensing technology. The sensitivity of chemical potential sensing in wavelength interrogation mode can be calculated to be 1.5, 1.89, 2.29, 3.21, 3.73 and 4.68 nm/meV respectively at the central wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. The much smaller full width half maximum (FWHMs) comparing with that of 2D nanomaterial-enhanced metal SPR sensors indicates higher figure of merit. The sensitivity of chemical potential sensing in gate voltage interrogation mode also can be calculated to be 156.9822, 143.6147, 131.0779, 111.0351, 101.3415 and 90.6038 mV/meV respectively at the incident wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. It can be estimated theoretically that the limit of detection (LOD) in DNA sensing of the proposed sensor can reach femtomolar level and even attomolar level, comparable to and even lower than that of 2D nanomaterial-enhanced metal SPR sensors with AuNPs as a sensitivity enhancement strategy. The feasibility of preparation and operation of this new concept SPR biosensor is also analyzed and discussed.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

Quantitative dynamic strain measurements of the ground would be useful for engineering scale problems such as monitoring for natural hazards, soil-structure interaction studies and non-invasive site investigation using full waveform inversion (FWI). Distributed Acoustic Sensing (DAS), a promising technology for these purposes, needs to be better understood in terms of its directional sensitivity, spatial position, and amplitude for application to engineering-scale problems. This study investigates whether the physical measurements made using DAS are consistent with the theoretical reception patterns and experimental measurements of ground strain made by geophones. Results show that DAS and geophone measurements are consistent in both phase and amplitude for broadband (10s of Hz), high amplitude (10s of microstrain) and complex wavefields originating from different positions around the array when: (1) the DAS channels and geophone locations are properly aligned, (2) the DAS cable provides good deformation coupling to the internal optical fiber, (3) the cable is coupled to the ground through direct burial and compaction, and (4) laser phase noise is mitigated in the DAS measurements. The theoretical relationship between DAS-measured and point-wise strain for vertical and horizontal active sources is introduced using 3D elastic finite-difference simulations. The implications of using DAS strain measurements are discussed including directionality and magnitude differences between the actual and DAS-measured strain fields. A method for spatially aligning the DAS channels with the geophone locations at tolerances less than the spatial resolution of the DAS system is proposed.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

Solid tumors universally possess the ability to evade contact inhibition of proliferation (CIP), a mechanism halting cell proliferation when cell-cell contacts occur. Merlin, an ERM-like protein, crucially regulates CIP and is frequently deactivated in various cancers, indicating its signifi-cance as a tumor suppressor in cancer biology. Despite extensive investigations into Merlin's role in cancer, its lack of intrinsic catalytic activity and frequent conformation changes has made it notoriously challenging to study. To address this challenge, we harnessed innovative luciferase technologies to create and validate a split-luciferase biosensor system. This system enables precise quantification of Merlin's conformation and activity both in vitro and within living cells. This biosensor significantly enhances the study of Merlin's molecular functions, serving as a potent tool to explore its contributions to CIP and tumorigenesis.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

The acoustic environment in learning spaces significantly influences learning effectiveness and occupant well-being. Recent studies have shown that a series of architectural factors within physical learning environments can impact students' educational experiences. This research delves into the relationship between architectural characteristics and the perceived acoustic environment among 467 primary students in 19 learning spaces across 9 schools in Chile. The survey comprises a student questionnaire, a checklist evaluating space characteristics, and acoustic measurements of indoor noise levels during occupied conditions. Examined topics include Indoor Environmental Quality (IEQ) comfort perception, noise annoyance, hearing ability, and acoustic preference. Architectural characteristics considered encompass flexible and acoustic space design parameters. The results indicated that noise discomfort was a common issue, especially in traditional learning spaces without acoustic treatment. The type of learning space (traditional or flexible settings) has a greater impact on acoustic perception particularly concerning noise discomfort and acoustic preference. However, poorly acoustic spaces lacking absorbing materials or exhibiting lower spatial density (m2 per student) contribute to increased indoor noise levels affecting noise annoyance caused by children's talking inside. The study emphasizes the importance of considering both architectural design and acoustic conditioning for optimizing the acoustic experience in educational spaces.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

This paper investigates the ion-acoustic wave structures in fluid ions for the Benjamin-Bona-Mahony-Peregrine-Burgers (BBMPB) equation. The various types of wave structures, are extracted including the three-wave hypothesis, breather wave, lump periodic, mixed-type wave, periodic cross-kink, cross-kink rational wave, M-shaped rational wave, M-shaped rational wave solution with one kink wave and M-shaped rational wave with two kink wave solutions. The Hirota bilinear transformation is a powerful tool that allows us to accurately solutions and predict the behavior of these wave structures. Through our analysis, we gain a better understanding of the complex dynamics of ion-acoustic waves and their potential applications in various fields. Moreover, our findings contribute to the ongoing research in plasma physics that utilize ion-acoustic wave phenomena. To show the physical behavior of the solutions, some 3D plots have been performed and their respective contour level, choosing different values of the parameters.

Assessing corneal biomechanics in vivo has long been a challenge in the field of ophthalmology. Although recent wave-based optical coherence elastography (OCE) methods have shown promise in this area, the effect of intraocular pressure (IOP) on mechanical wave propagation in the cornea remains unclear. To address this, we constructed an artificial eye model and performed surface wave OCE measurements in the radial directions (54–324°) of the silicone cornea at varying IOP levels (10–40 mmHg). The results demonstrated increases in wave propagation speeds (mean ± STD) from 6.55 ± 0.09 m/s (10 mmHg) to 9.82 ± 0.19 m/s (40 mmHg), leading to an estimate of Young’s modulus, which increased exponentially from 145.23 ± 4.43 kPa to 326.44 ± 13.30 kPa. Our implementation of an artificial eye model highlighted that the impact of IOP on Young’s modulus (ΔE = 165.59 kPa, IOP: 10–40 mmHg) was more significant than the effect of stretching of the silicone cornea (ΔE = 15.79 kPa, relative elongation: 0.98%–6.49%). Our study sheds light on the potential of using an artificial eye model in OCE research for corneal biomechanics. Furthermore, it is critical to consider the impact of IOP on measurement results when utilizing wave-based OCE in clinical settings for enhanced assessment of corneal biomechanics.

Biosensors are essential tools which have been traditionally used to monitor environmental pollution, detect the presence of toxic elements and biohazardous bacteria or virus in organic matter and biomolecules for clinical diagnostics. In the last couple of decades, the scientific community has witnessed their widespread application in the fields of military, health care, industrial process control, environmental monitoring, food-quality control, and microbiology. Biosensor technology has greatly evolved from the in vitro studies based on the biosensing ability of organic beings to the highly sophisticated world of nanofabrication enabled miniaturized biosensors. The incorporation of nanotechnology in the vast field of biosensing has led to the development of novel sensors and sensing mechanisms, as well as an increase in the sensitivity and performance of the existing biosensors. Additionally, the nanoscale dimension further assists the development of sensors for rapid and simple detection in vivo as well as the ability to probe single-biomolecules and obtain critical information for their detection and analysis. However, the major drawbacks of this include, but are not limited to potential toxicities associated with the unavoidable release of nanoparticles into the environment, miniaturization induced unreliability, lack of automation, and difficulty of integrating the nanostructured-based biosensors as well as unreliable transduction signals from these devices. Although the field of biosensors is vast, we intend to explore various nanotechnology enabled biosensors as part of this review article and provide a brief description of their fundamental working principles and potential applications.

The present Feature Paper highlights the application of bacterial surface (S-) layer proteins as versatile components for the fabrication of biosensors. One technologically relevant feature of S‑layer proteins is their ability to self-assemble on many surfaces and interfaces to form a crystalline 2D protein lattice. The S-layer lattice on the surface of a biosensor becomes part of the interface architecture, linking the bioreceptor to the transducer interface, which may cause signal amplification. The S-layer lattice as ultrathin, highly porous structure with functional groups in a well-defined special distribution and orientation and an overall anti-fouling characteristics can significantly raise the limit in terms of variety and ease of bioreceptor immobilization, compactness of bioreceptor molecule arrangement, sensitivity, specificity, and detection limit for many types of biosensors. The present paper discusses and summarizes examples for the successful implementation of S-layer lattices on biosensor surfaces in order to give a comprehensive overview on the application potential of these bioinspired S-layer protein-based biosensors.

Safety and quality are key issues for the food industry. Consequently, there is a growing demand to preserve the food chain and products against substances toxic, harmful to human health such as contaminants, allergens, toxins, or pathogens. For this reason, it is mandatory to develop highly sensitive, reliable, rapid, and cost-effective sensing systems/devices such as electrochemical sensors/biosensors. Generally, conventional techniques are limited by long time of analyses, expensive and complex procedures, and they require skilled personnel. Therefore, the development of performant electrochemical biosensors can significantly support the screening of food chain and products. Here, we report some of the recent developments in this area and analyze the contributions produced by electrochemical biosensors in the food screening and the challenges to address.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

Seismic travel time tomography using surface waves is an effective tool for three-dimensional crustal imaging. Historically, these surface waves are the result of active seismic sources or earthquakes. More recently, however, also surface waves retrieved through the application of seismic interferometry are exploited. Conventionally, two-step inversion algorithms are employed to solve the tomographic inverse problem. That is, a first inversion results in frequency-dependent, two-dimensional maps of phase velocity, which then serve as input for a series of independent, one-dimensional frequency-to-depth inversions. As such, a two-dimensional grid of localized depth-dependent velocity profiles are obtained. Stitching these separate profiles together subsequently yields a three-dimensional velocity model. Relatively recently, a one-step three-dimensional non-linear tomographic algorithm has been proposed. The algorithm is rooted in a Bayesian framework using Markov chains with reversible jumps, and is referred to as transdimensional tomography. Specifically, the three-dimensional velocity field is parameterized by means of a polyhedral Voronoi tessellation. In this study, we investigate the potential of this algorithm for the purpose of recovering the three-dimensional surface-wave-velocity structure from ambient noise recorded on and around the Reykjanes Peninsula, southwest Iceland. To that end, we design a number of synthetic tests that take into account the station configuration of the Reykjanes seismic network. We find that the algorithm is able to recover the 3D velocity structure at various scales in areas where station density is high. In addition, we find that the standard deviation on the recovered velocities is low in those regions. At the same time, the velocity structure is less well recovered in parts of the peninsula sampled by fewer stations. This implies that the algorithm successfully adapts model resolution to the density of rays. Also, it adapts model resolution to the amount of noise on the travel times. Because the algorithm is computationally demanding, we modify the algorithm such that computational costs are reduced while sufficiently preserving non-linearity. We conclude that the algorithm can now be applied adequately to travel times extracted from (time-averaged) station-station cross correlations by the Reykjanes seismic network.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

We review time expansion wave theory and refine our model showing it to accurately match observed cosmological luminosity data. The theory augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension that we observe as the expansion of the universe. This leads us to explain mass creation, the speed of light limit, gravity, black holes without singularities and other macroscopic effects. Our model leads to an expansion velocity of 6.87 0.36 × 106 ms-1, which results in a Hubble expansion rate constant of 71.3 3.7 km/s/Mpc. Because of the finite window of time in which we exist, an extra a degree of freedom is available leading to interesting interpretations at the subatomic level. At this size range, then a spin is allowed within the time dimension explaining why wave particle duality occurs and explains the electromagnetic force and other quantum mechanical properties. It provides a solution to the double slit conundrum and can explain how quantum entangled partners can behave in a quantum way and pass seemingly time-defying information. The potential quantitative origin of the fine structure constant which governs the size of the electromagnetic force is also strongly indicated by this theory.

By using Modified simple equation method, we study the Cahn Allen equation which arises in many scientific applications such as mathematical biology, quantum mechanics and plasma physics. As a result, the existence of solitary wave solutions of the Cahn Allen equation is obtained. Exact explicit solutions interms of hyperbolic solutions of the associated Cahn Allen equation are characterized with some free parameters. Finally, the variety of structure and graphical representation make the dynamics of the equations visible and provides the mathematical foundation in mathematical biology, quantum mechanics and plasma physics.

The rapid and sensitive detection of pathogenic bacteria is becoming increasingly important for the timely prevention of contamination and treatment of infections. Biosensors based on nucleic acid aptamers integrat-ed with optical, electrochemical, and mass-sensitive analytical techniques have garnered intense interest for their versatility, cost-efficiency, and ability to exhibit high affinity and specificity in binding bacterial bi-omarkers, toxins, and whole cells. This review emphasizes the development of aptamers, their structural op-timization, and their use in bacterial sensing applications. Moreover, we explore barriers and develop per-spectives in applying aptamer-based bacterial detection.

Bioelectrocatalysis provides the intrinsic catalytic-functions of redox enzymes to non-specific electrode reactions and is the most important and basic concept for biosensors. This review starts by describing fundamental characteristics of bioelectrocatalytic reactions in mediated and direct electron transfer types from a theoretical viewpoint and summarizes amperometric biosensors based on multi-enzymatic cascades and for multi-analyte detection. The review also introduces prospective aspects of two new concepts of biosensors: mass-transfer-controlled (pseudo)steady-state amperometry at microelectrodes with enhanced enzymatic activity without calibration curves and potentiometric coulometry at enzyme/mediator-immobilized biosensors for absolute determination.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Graphene quality for use in biosensors was assessed in fabricated chips by a set of methods that includes atomic force microscopy (AFM), Raman spectroscopy, and low-frequency noise. It is shown that local areas of residues on the graphene surface, which arisen due to the interaction of graphene with a photoresist at the initial stage of chips development, leads to a spread of chips resistance (R) within 1-10 kΩ and to an increase in the root mean square (RMS) roughness up to 10 times that can significantly impair reproducibility of graphene parameters in biosensors chips. It was observed that the control of the photoresist residues after photolithography (PLG) by AFM and subsequent additional cleaning allow reducing the spread of R values in chips to 1–1.6 kΩ and obtaining RMS roughness similar to the roughness in pristine graphene before PLG. Monitoring of the spectral density of low-frequency voltage fluctuation (SU), which provides integral information about the defect system and quality of the material, makes it possible to identify chips with low graphene quality and with inhomogeneously distributed compressive stresses areas by the type of frequency dependence SU (f).

Fluorescent hydrogels are promising candidate materials for portable biosensors to be used in point-of-care diagnosis because (1) they have a greater capacity for binding organic molecules than immunochromatographic test systems, determined by the immobilization of affinity labels within the three-dimensional hydrogel structure; (2) fluorescent detection is more sensitive than the colorimetric detection of gold nanoparticles or stained latex microparticles; (3) the properties of the gel matrix can be finely tuned for better compatibility and detection of different analytes; and (4) hydrogel biosensors can be made reusable and suitable for studying dynamic processes in real time. Water-soluble fluorescent nanocrystals are widely used for in vitro and in vivo biological imaging due to their unique optical properties, and hydrogels based on them allow preserving these properties in bulk composite macrostructures. Here we review the techniques for obtaining analyte-sensitive fluorescent hydrogels based on nanocrystals, the main methods used for detecting the fluorescent signal changes, and the approaches to the formation of inorganic fluorescent hydrogels via sol–gel phase transition using surface ligands of the nanocrystals.

The deadliest disease in the world, cancer, kills many people every year. The early detection is the only hope for the survival of malignant cancer patients. As a result, in the preliminary stages of , the diagnosis of cancer biomarkers at the cellular level is critical for improving cancer patient survival rates. For decades, scientists have focused their efforts on the invention of biosensors. Biosensors, in addition to being employed in other practical scenarios, can essentially function as cost effective and highly efficient devices for this purpose. Traditional cancer screening procedures are expensive, time-consuming, and inconvenient for repeat screenings. Biomarker-based cancer diagnosis, on the other hand, is rising as one of the most potential tools for early detection, disease progression monitoring, and eventual cancer treatment. As Biosensor is an analytical device, it allows the selected analyte to bind to the biomolecules being studied (– for example RNA, DNA, tissue, proteins, cells). They can be divided based on the kind of biorecognition or transducer elements on the sensor. Most biosensor analyses necessitate the analyte being labeled with a specific marker. In this review article, the application of distinct variants of biosensors against cancer has been described.

The development of biosensors with high sensitivity and low-detection limits provides a new direction for medical and personal care. Graphene and graphene derivatives have been used to prepare various types of biosensors due to their excellent sensing performance (e.g. high specific surface area, extraordinary electronic properties, electron transport capabilities and ultrahigh flexibility). This perspective review focuses on graphene-based biosensors for quantitative detection of cancer related biomarkers such as DNA, miRNA, small molecules and proteins by integrating with different signal outputting approaches including fluorescent, electrochemistry, surface plasmon resonance, surface enhanced Raman scattering etc. The article also discussed their challenges and potential solutions along with future prospects.

Thanks to advanced semiconductor microfabrication technology, chip-scale integration and miniaturization of lab-on-a-chip components, silicon-based optical biosensors have made significant progress for the purpose of point-of-care diagnosis. In this review, we provide an overview of the state-of-the-art in evanescent field biosensing technologies including interferometer, microcavity, photonic crystal, and Bragg grating waveguide-based sensors. Their sensing mechanisms and sensor performances, as well as real biomarkers for label-free detection, are exhibited and compared. We also review the development of chip-level integration for lab-on-a-chip photonic sensing platforms, which consist of the optical sensing device, flow delivery system, optical input and readout equipment. At last, some advanced system-level CMOS-chip packaging examples are presented, indicating the commercialization potential for the low cost, high yield, portable biosensing platform leveraging CMOS processes.

The effects of the surface waves generated by the wind have a significant effect on the currents. A wave current coupled model plays an important role in the design of offshore structures. The interaction between fluids such as incompressible ocean waves and current and offshore structures is significant with many real-time applications in offshore engineering. These coupled models can be applied to Offshore Floating Production Operating and offloading (FPSO), Wind or current turbines and offshore pipelines. The complex issues related to the design are analyzed by using Computational Fluid Dynamics, which requires an investigation of the multiphase flow between wave and current and the structure which is considered restrictive due to the computational cost. If viscous effects are neglected then the single-phase flow models have been recommended, where wave-current interaction have been modelled successfully. Models have been developed where velocities and pressure are computed and the results can be verified with the experimental results available in the literature. In this study the existing numerical methods, mesh types are discussed along with their coupling methods. Here single-phase and multiphase models with small and medium movement are reviewed and their applications are highlighted.

This study aims at an acoustic design of the classical concert hall and evaluation of the acoustic performance. In terms of three acoustic parameters (i.e., reverberation time (RT), clarity (C80), and lateral fraction (LF)), this study performed acoustic simulation modeling and site measurement with the K Art Hall located in South Korea as a case study. First, in order to meet the acoustic performance of the K Art Hall (target RT: 1.4~1.7 seconds, target C80: -2dB or more +2dB or less, and target LF: 10~35%), the finish materials and shape of the room as an interior acoustic design were determined. Second, the average values of the RT, C80, and LF using the acoustic simulation modeling were estimated at 1.4 second, 1.2~1.6 dB, and 29%, respectively. Third, the average values of the RT, C80, and LF through site measuring were measured at 1.5~1.64 second, 0.07~1.31dB, and 22.22~31.37%, respectively. Thus, the results of both the acoustic simulation modeling and site measuring were analyzed so as to satisfy the target acoustic performance. The results of this study will help the decision-makers (i.e., owner, construction managers, etc.) to plan the classical concert hall in terms of the RT, C80, and LF.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

Metamaterials, man-made composites scaled smaller than the wavelength, have demonstrated a huge potential in their applications in acoustics, opening up for sub--wavelength acoustic absorbers, acoustic invisibility, perfect acoustic mirrors and acoustic lenses for hyper focusing, acoustic illusions and enabling new degrees of freedom in the control of the acoustic field. The zero, or even negative, refractive sound index of metamaterials offers possibilities in control of the acoustic pattern and sound at sub--wavelength scales. Despite the tremendous growth of the research on acoustic metamaterials during the last decade, the potential of metamaterial-based technologies in aeronautics is still not fully explored and its utilization is still in its infancy. Thus the principal concepts mentioned above could very well provide means to develop devices that would allow the mitigation of the impact of the civil aviation noise on the community. This paper gives a review of the state of the art of the most relevant works on acoustic metamaterials, analyzing them against their potential applicability in aeronautics, and in this process identifying possible implementation areas and interesting metabehaviors. It also identifies some technical challenges and possible future directions for research with the goal of unveiling the potential of metamaterials technologies in aeronautics.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Wave steepness is presented as an extension and a valuable add-on to the conventional set of sea state parameters retrieved from satellite altimetry data. Following physical model based on recent advances of weak turbulence theory wave steepness is estimated from directly measured spatial gradient of wave height. In this way the method works with altimetry trajectories rather than with point-wise data. Moreover, in contrast to widely used parametric models this approach provides us with instantaneous values of wave steepness and period. Relevance of single-track estimates of wave steepness (period) is shown for wave climate studies and confirmed by a simple probabilistic model. The approach is verified via comparison against buoy and satellite data including crossover points for standard 1 second data of Ku-band altimeters. High quality of the physical model and robustness of the parametric ones are examined in terms of global wave statistics. Prospects and relevance of both approaches in the ocean wave climate studies are discussed.

Biosensors are indispensable tools to follow plant’s immunity as its spatiotemporal dimension is key in withstanding the complex plant immune signaling. The diversity of genetically encoded biosensors in plants is expanding, covering new analytes with ever higher sensitivity and robustness, but their assortment is limited in some aspects, such as their use to follow biotic stress response, employing more than one biosensor in the same chassis and their implementation into crops. In this review, we focused on the available biosensors that encompass these aspects. We show that in vivo imaging of calcium and reactive oxygen species is satisfactorily covered with the available genetically encoded biosensors, while on the other hand they are still underrepresented when it comes to imaging of the main three hormonal players of the immune response, salicylic acid, ethylene and jasmonic acid. Following more than one analyte in the same chassis, upon one or more conditions has so far been possible by using the most advanced genetically encoded biosensors in plants which allow to monitor calcium and two main hormonal pathways involved in plant development, auxin and cytokinin. These kinds of biosensors are also the most evolved in crops. In the last section, we gathered the challenges in the use of the biosensors and showed some strategies to overcome them.

Antibiotic resistance and accordingly their pollution because of uncontrolled usage has emerged as a serious problem in recent years. Hence, there is an increased demand to develope robust, easy, and sensitive methods for rapid evaluation of antibiotic and their residues. Among different analytical methods, the aptamer-based biosensors (aptasensors) have attracted considerable attention because of good selectivity, specificity, and sensitivity. This review gives an overview about recent developed aptasensors for antibiotic detection. The use of various aptamer assays to determine different groups of antibiotics like β-lactams, Aminoglycosides, Anthracyclines, Chloramphenicol, (Fluoro)Quinolones, Lincosamide, Tetracyclines and Sulfonamides are presented in this paper.

Two distinct measures of information, connected respectively to the amplitude and phase of the wave function of a particle, are proposed. There are relations between the time derivatives of these two measures and their gradients on the configuration space, which are equivalent to the wave equation. The information related to the amplitude measures the strength of the potential coupling of the particle (which is itself aspatial) with each volume of its configuration space, i.e. its tendency to participate in an interaction localized in a region of ordinary physical space corresponding to that volume. The information connected to the phase is that required to obtain the time evolution of the particle as a persistent entity starting from a random succession of bits. It can be considered as the information provided by conservation principles. The meaning of the so-called "quantum potential" in this context is briefly discussed.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Chymotrypsin is an important proteolytic enzyme in human digestion system that cleaves milk proteins, through hydrolysis reaction, which makes it interesting subject to study activity of milk proteases. In this work, we compared detection of chymotrypsin by spectrophotometric, dynamic light scattering (DLS) and quartz crystal microbalance (QCM) methods and determined the limit of chymotrypsin detection (LOD), 0.15 ± 0.01 nM for spectrophotometric, 0.67 ± 0.05 nM for DLS and 1.40 ± 0.30 nM for QCM methods, respectively. We discuss peculiarities and give perspective for implementation of detection methods and note that while the optical detection methods are simple to implement, the QCM method is more robust for sample preparation. We give an overview on methods and instruments for detection of chymotrypsin and other milk proteases.

Tamm Plasmon Polariton (TPP) is a nanophotonic phenomenon that has attracted much attention due to its spatial strong field confinement, ease of mode excitation and polarization independence. TPP has applications in sensing, storage, lasing, perfect absorber, solar cell, nonlinear optics, and many others. In this work, we demonstrate a biosensing platform based on TPP resonant mode. Both theoretical analyses based on Transfer Matrix Method and experimental validation through nonspecific detection of liquids of different refractive indices and specific detection of SARS-CoV-2 nucleocapsid protein (N-protein) are presented. Results show that TPP biosensor has high sensitivity and good specificity. For N-protein detection, the sensitivity is 1.5 nm/(µg/ml) and the limit of detection can reach down to below 7 ng/ml with spectrometer of 0.01 nm resolution of wavelength shift. This work paves the way for design, optimization, fabrication, characterization, and performance analysis of TPP based biosensors

Electrochemical biosensors based on immobilized enzymes are among the most popular and commercially successful biosensors. Literature in this field suggests that modification of electrodes with nanomaterials is an excellent method for enzyme immobilization, which can greatly improve the stability and sensitivity of the sensor. However, the poor stability, weak reproducibility, and limited lifetime of the enzyme itself still limit the requirements for the development of enzyme electrochemical biosensors for food production process monitoring. Therefore, constructing sensing technologies based on enzyme electrochemical biosensors remains a great challenge. This article outlines the construction principles of four generations of enzyme electrochemical biosensors and discusses the applications of single-enzyme systems, multi-enzyme systems and nano-enzyme systems developed based on these principles. The article further describes methods to improve enzyme immobilisation by combining different types of nanomaterials such as metals and their oxides, graphene-related materials, metal-organic frameworks, carbon nanotubes and conducting polymers. In addition, the article highlights the challenges and future trends of enzyme electrochemical biosensors, providing theoretical support and future perspectives for further research and development of high-performance enzyme chemical biosensors.

Coagulant lectin from Moringa oleifera seeds (cMoL) was characterized by potentiometry and scanning electron microscopy (SEM) using MOF, Metal-Organic Frameworks of [Cu3(BTC)2.H2O)3]n, to immobilize cMoL and construct biosensors. Developed aluminum-air batteries degraded indigo carmine dye formulated similar to a textile effluent; biosensors investigated cMoL interaction with specific galactose and monitored residual dye. SEM revealed components of electrode assembly steps. Oxide reduction reactions of batteries generated Al(OH)3 promoting dye electrocoagulation. Cyclic voltammetry showed differentiated redox peaks related to dye residue quantification by cMoL. Electrochemical systems evaluated cMoL interaction with ligand and efficiently degraded dye; biosensors could be used for lectin characterization and monitoring dye residues in environmental textile effluents.

Whole cell biosensors could serve as eco-friendly and cost-effective alternatives for detecting potentially toxic bioavailable heavy metals in aquatic environments. However, they often fail to meet practical requirements due to an insufficient limit of detection (LOD) and high background noise. In this study, we designed a synthetic genetic circuit specifically tailored for detecting ionic mercury, which we applied to environmental samples collected from artisanal gold mining sites in Peru. We developed two distinct versions of the biosensor, each utilizing a different reporter protein: a fluorescent biosensor (Mer-RFP) and a colorimetric biosensor (Mer-Blue). Mer-RFP enabled real-time monitoring of the culture’s response to mercury samples using a plate reader, whereas Mer-Blue was analysed for colour accumulation at the endpoint using a specially designed, low-cost camera set up for harvested cell pellets. Both biosensors exhibited negligible baseline expression of their respective reporter proteins and responded specifically to HgBr2 in pure water. Mer-RFP demonstrated a linear detection range from 1 nM to 1 μM, whereas Mer-Blue showed a linear range from 2 nM to 125 nM. Our biosensors successfully detected a high concentration of ionic mercury in the reaction bucket where artisanal miners produce a mercury-gold amalgam. However, they did not detect ionic mercury in the water from active mining ponds, indicating a concentration lower than 3.2 nM Hg2+ -a result consistent with chemical analysis quantitation. Furthermore, we discuss the potential of Mer-Blue as a practical and affordable monitoring tool, highlighting its stability, reliance on simple visual colorimetry, and the possibility of sensitivity expansion to organic mercury.

: Microbial fuel cell (MFCs) devices utilise the metabolic processes of bacteria to generate electricity from various organic substrates. Due to the enormous amount of energy that organic waste produces, scientists are highly interested in advanced MFCs. MFCs serve as a multidisciplinary research platform at the engineering and natural sciences intersection. MFCs have various uses besides being used as energy sources, such as sensing capabilities. Despite showing considerable promise, only a few marine sediment MFCs have been deployed in real-world applications to supply current for low-power devices. It is now required to maintain track of the work being done by research groups worldwide and regularly compile significant discoveries due to the rising quantity of research publications. Review papers are a traditional beginning point for a literature review for new scholars. This review is a fast reckoner that directs readers to pertinent reviews and research publications detailing significant advances in microbial fuel cell research during the previous two decades. An overview of key advances in MFC research over the past two decades is provided as a quick reference in this review article. In addition, the report identifies research gaps that, if filled, could bring this technology closer to real-world use.

Planetary waves in the mesosphere are studied using observational data and models to establish their origin, as there are indications of their generation independently of waves in the stratosphere. The quantitative relationships between zonal wave numbers m = 1 (wave 1) and m = 2 (wave 2) were studied with a focus on the mid-latitude mesosphere at 50N latitude. Aura Microwave Limb Sounder measurements were used to estimate wave amplitudes in geopotential height during the 2020–2021 winter major sudden stratospheric warming. The moving correlation between the wave amplitudes shows that, in comparison with the anticorrelation in the stratosphere, wave 2 positively correlates with wave 1 and propagates ahead of it in the mesosphere. A positive correlation r = 0.5–0.6, statistically significant at the 95% confidence level, is observed at 1–5-day time lag and in the 75–91 km altitude range, which is the upper mesosphere–mesopause region. Wavelet analysis shows a clear 8-day period in waves 1 and 2 in the mesosphere at 0.01 hPa (80 km), while in the stratosphere–lower mesosphere the period is twice as long at 16-days; this is statistically significant only in wave 2. Possible sources of mesospheric planetary waves are discussed.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

The main goal of the paper is to compare the effects of the wave spectrum, computed using the Discrete Interaction Approximation (DIA) and the Webb–Resio–Tracy (WRT) methods, on statistical wave properties such as skewness and kurtosis. The statistical properties are obtained by integrating the three-dimensional free-surface Euler equations with a high-order spectral method combined with a phenomenological filter to account for the energy dissipation due to breaking waves. In addition, we investigate the minimum spatial domain size required to obtain meaningful statistical wave properties. The numerical simulations are performed over a physical domain of size 4.13 km × 4.13 km. The results indicate that statistical properties must be computed over an area of at least 4 km2. The results also suggest that selecting a more computationally expensive WRT method does not affect the statistical values to a great extent. The most noticeable effect is due to the energy dissipation filter that is applied. It is concluded that selecting the WRT or the DIA algorithm for computing the wave spectrum needed for the numerical simulations does not lead to major differences in the statistical wave properties. However, more accurate energy dissipation mechanisms due to wave breaking are needed.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

Hydrogel-based wearable electrochemical biosensors (HWEBs) are emerging biomedical devices that have recently received immense interest. The exceptional properties of HWEBs include excellent biocompatibility with hydrophilic nature, high porosity, tailorable permeability, the capability of reliable and accurate detection of disease biomarkers, suitable device-human interface, facile adjustability, and stimuli-responsive to the nanofiller materials. Although the biomimetic three-dimensional hydrogels can immobilize bioreceptors, such as enzymes and aptamers, without any loss in their activities. However, most HWEBs suffer from low mechanical strength and electrical conductivity. Many studies have been performed on emerging electroactive nanofillers, including biomacromolecules, carbon-based materials, and inorganic and organic nanomaterials, to tackle these issues. Non-conductive hydrogels and even conductive hydrogels may be modified by nanofillers as well as redox species. All these modifications have led to the design and development of efficient nanocomposites as electrochemical biosensors. In this review, both conductive-based and non-conductive-based hydrogels derived from natural and synthetic polymers are systematically reviewed. The main synthesis methods and characterization techniques are addressed. The mechanical properties and electrochemical behavior of HWEBs are discussed in detail. Finally, the prospects and potential applications of HWEBs in biosensing, healthcare monitoring, and clinical diagnostics are highlighted.

Biosensors are measurement devices that can sense several biomolecules, and are widely used for the detection of relevant clinical pathogens such as bacteria and viruses, showing outstanding results. Because of the latent existing risk of facing another pandemic like the one we are living due to COVID-19, researchers are constantly looking forward to developing new technologies for diagnosis and treatment of infections caused by different bacteria and viruses. Regarding that, nanotechnology has improved biosensors design and performance through the development of materials and nanoparticles that enhance their affinity, selectivity, and efficacy in detecting these pathogens, such as employing nanoparticles, graphene quantum dots, and electrospun nanofibers. Therefore, this work aims to present a comprehensive review that exposes how biosensors work in terms of bacterial and viral detection, and the nanotechnological features that are contributing to achieving a faster yet still efficient COVID-19 diagnosis at the point-of-care.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Chitosan is a biopolymer derived from chitin. It is a non-toxic, biocompatible, bioactive, and biodegradable polymer. Due to its properties, chitosan has found applications in several and different fields such as agriculture, food industry, medicine, paper fabrication, textile industry, and water treatment. In addition to these properties, chitosan has a good film-forming ability which allows it to be widely used for the development of sensors and biosensors. This review is focused on the use of chitosan for the formulation of electrochemical chemosensors. It also aims to provide an overview of the advantages of using chitosan as an immobilization platform for biomolecules by highlighting its applications in electrochemical biosensors. Finally, applications of electro-chemical chitosan-based chemosensors and biosensors in food safety are illustrated

Spray technology is widely used in various industries, including medicine, food production, mechanical engineering, and nanopowder manufacturing. Achieving high dispersion and a narrow particle size distribution is crucial for many applications. Ultrasonic spraying is commonly used to achieve this. On other hand, hydraulic nozzles provide high atomization performance. Combining these two technologies promises to offer significant benefits, but the complex processes that occur simultaneously in such a device require careful study. This work proposes a fundamental design for an acoustic-hydraulic nozzle and investigates the physical processes when a liquid is sprayed using this nozzle, both theoretically and experimentally. The study identifies the critical modes of spraying and confirms that the simultaneous use of ultrasound and hydraulic pressure can produce a fine spray (droplet size less than 50 μm) with high productivity (5-10 ml/s). This approach has significant potential for modern industries and technologies.

The development of sensitive and specific exosome detection devices is highly desirable because it is believed to deliver specific important information for cancer screening, diagnosis, and monitoring. Among many detection techniques, nanoplasmonic sensors are optical detection methods that offer advantages in sensitivity and detection speed and this makes the sample analysis process faster and more accurate. This paper summarizes the development of nanoplasmonic biosensors, especially Surface Plasmon Resonance (SPR) and Localized Surface Plasmon Resonance (LSPR)-based biosensors for exosome detection. There are three main parts in this paper. The first part will focus on introducing the theoretical background regarding the working principles of SPR and LSPR biosensors. After that, we will introduce several methods that can be used for exosome isolation. This article will close by explaining the engineering of nanoplasmonic sensors both in terms of transducer modification to amplify the signal and functionalization strategies to increase sensor specificity. In this section, the detection mechanism, the type of exosomes detected, and the resulting detection limits are some of the points highlighted in this paper.

Early diagnosis and treatment have always been highly desired in the fight against cancer, and detection of circulating tumor DNA (ctDNA) has recently been touted as highly promising for early cancer screening. Consequently, the detection of ctDNA in liquid biopsy gains much attention in the field of tumor diagnosis and treatment, which has also attracted research interest from the industry. However, traditional gene detection technology is difficult to achieve low cost, real-time and portable measurement of ctDNA. Electroanalytical biosensors have many unique advantages such as high sensitivity, high specificity, low cost and good portability. Therefore, this review aims to discuss the latest development of biosensors for minimal-invasive, rapid, and real-time ctDNA detection. Various ctDNA sensors are reviewed with respect to their choices of receptor probes, detection strategies and figures of merit. Aiming at the portable, real-time and non-destructive characteristics of biosensors, we analyze their development in the Internet of Things, point-of-care testing, big data and big health.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

This manuscript employs a surface stress-driven nonlocal model to explore the combined effects of long-range interaction and surface energy on higher vibration modes of functionally graded nanobeams. The nanobeam theory, based on Bernoulli-Euler kinematics, incorporates surface effects such as surface elasticity, surface residual stresses, surface density, and rotary inertia. Hamilton's principle is applied to derive the governing equation with size-dependent considerations. The main outcomes of a parametric investigation, considering four different kinematic boundary conditions (Cantilever, Simply-Supported, Clamped-Pinned, and Doubly-Clamped) while varying the nonlocal parameter and material gradient index, are presented and discussed. Additionally, the normalized natural frequencies for the second, third, fourth and fifth modes of vibrations are provided and analyzed for each case under study. The results underscore the model's effectiveness in capturing surface energy effects on the overall dynamic behavior of functionally graded Bernoulli-Euler nanobeams, offering a cost-effective approach for designing and optimizing nano-scaled structures.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Melatonin is a ubiquitous molecule found in living organisms, ranging from bacteria to plants and mammals. It possesses various properties, partly due to its robust antioxidant nature and partly owed to its specific interaction with melatonin receptors present in almost all tissues. Melatonin regulates different physiological functions and contributes to the homeostasis of the entire organism. In the human eye, a small amount of melatonin is also present, produced by cells in the anterior segment and the posterior pole, including the retina. In the eye, melatonin may provide antioxidant protection along with regulating physiological functions of ocular tissues, including intraocular pressure (IOP). Therefore, it is conceivable that the exogenous administration of sufficiently high amounts of melatonin to the eye could be beneficial in several instances: for the treatment of eye pathologies like glaucoma, due to the IOP-lowering and neuroprotection effects of melatonin; for the prevention of other dysfunctions, such as dry eye and refractive defects (cataract and myopia) mainly due to its antioxidant properties; for diabetic retinopathy due to its metabolic influence and neuroprotective effects; for macular degeneration due to the antioxidant and neuroprotective properties; and for uveitis, mostly owing to anti-inflammatory and immunomodulatory properties. This paper reviews the scientific evidence supporting the use of melatonin in different ocular districts and provides data suggesting that the topical administration of melatonin as eye drops is a real possibility. This way, its distribution and concentration in different ocular tissues may support its pleiotropic therapeutic effects.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

(1) Background: A simple approach to map irrigated landcover has been introduced by using measures derived from optical spectral range as an alternative to thermal range. It has been demonstrated that substituting surface temperature (Ts, ‘thermal approach’) with SWIR transformed reflectance (STR, ‘optical approach’) to detect surface moisture is feasible with comparable results. (2) Methods: Using an iterative thresholding procedure to minimize within-class variance, the bilevel segmentation of variables derived from Landsat-8 representing surface moisture and vegetation cover was achieved for the 2020-21 summer for a key irrigation district in Australia. (3) Results: The results of irrigated landcover by optical approach found to be comparable with those by thermal approach. The classification accuracy was assessed using water delivery records at farm level. Though the overall accuracy is high in both cases, the optical approach (97.6%) performed slightly better than the thermal approach (93.9%). (4) Conclusions: The feasibility of using STR to map irrigated landcover has been confirmed by a high-level overall accuracy assessment. This has broader implications in terms of irrigated landcover assessment, as the use of satellite imagery in these applications may not necessarily be limited to microwave or thermal sensors.

Manipulation of radiation pattern control is challenging, especially at low frequencies. In this paper, we demonstrate that acoustic metamaterials as an effective array of quadrupoles can remarkably improve the directionality of acoustic radiation at low frequencies, compared with previous metamaterials as monopole and dipole structures. The directivity of the acoustic radiation can be adjusted by changing the characteristic parameter and the symmetry of the structure, which provide a flexible method of adjustable radiation di-rections. The directionality can be further improved by constructing linear array of structure. Our work opens an approach of acoustic radiation control via quadrupolar metamaterials.

This study explores the dependence of drone acoustic detection systems performance on distance, using learning machines with different complexities, from simple linear discriminants, to deep neural networks, such as YAMNet, which exploits transfer learning. Other machine learning systems studied are the multilayer perceptron, support vector machines and random forest. These methods have been evaluated with a meticulously selected database that includes a wide variety of drone and interference sounds, previously processed by array signal processing and affected by ambient noise. Two strategies for training learning machines are considered. In the first one, they are trained with unattenuated signals, trying to preserve the information generated by the sound sources, but they are tested considering the attenuation with distance, achieving effective detection at distances up to 200 metres with some methods, especially linear discriminant. In all cases, the existence of interferences that hinder detection is considered. In the second strategy, the systems are trained and tested with attenuated signals as a function of distance. The effective detection range increases up to 300 metres for most methods and up to 500 metres for the YAMNet based detector. In addition, this second approach raises the possibility of developing specialised detectors for each distance range, thus significantly extending the effective detection range. These results underline the promising potential of acoustic detection of drones at various distances, encouraging further exploration in this research area.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

The unique porous crystal structure of zeolite offers various important utilizations, it is one of the considerations in selecting zeolite at this study as component of composite for restraining noise. It so happens, previous experiments show that banana stem has porous structure, fibrous, high flexibility and can be applied as material for many various products including as component of acoustic material. The combination of both is alleged that it has capability in absorbing noise. This paper presents an investigation on the composite that it was synthesized of Activated Zeolite and Banana Stem Fibre in various weight for determining its sound absorption coefficient alpha (a). Activating natural zeolite was conducted by using 6M HCl in order for enlarging zeolite pores. The sound absorption coefficient was measured in the frequency range between 125 Hz up to 6000 Hz. The results show that the different weight of banana stem fibre as component of the synthesized composite affects the value of alpha and shifts the frequency area.

Field-effect transistor (FET)-based biosensors stand as powerful analytical tools for detecting trace-specific biomolecules in diverse sample matrices, especially in the realms of pandemics and infectious diseases. The primary concern in applying these biosensors is their stability, a factor directly impacting the accuracy and reliability of sensing over extended durations. The risk of biosensor degradation is substantial, potentially jeopardizing sensitivity and selectivity and leading to inaccurate readings, including the possibility of false positives or negatives. This paper delves into the documented degradation of silicon nanobelt FET (NBFET) biosensors induced by buffer solutions. The results highlight a positive correlation between immersion time and the threshold voltage of NBFET devices. Secondary ion mass spectrometry analysis demonstrates a gradual increase in sodium and potassium ion concentrations within the silicon as immersion days progress. This outcome is ascribed to the nanobelt's exposure to the buffer solution during the biosensing period, enabling ion penetration from the buffer into the silicon. The study emphasizes the critical need to address buffer solution-induced degradation to ensure the long-term stability and performance of FET-based biosensors in practical applications.

We describe a machine learning (ML) approach to process the signals collected from Covid-19 optical-based detector. Multilayer Perceptron (MLP) and Support Vector Machine (SVM) were used to process both raw data and feature engineering data, and high performances for qualitative detection of the SARS-CoV-2 virus with concentration down to 1 TCID50/ml has been achieved. Valid detection experiments contain 486 negative and 108 positive samples; and control experiments, in which biosensors without antibody functionalization were used to detect SARS-CoV-2, contains 36 negative samples and 732 positive samples. Data distribution patterns of the valid and control detection dataset, based on T-distributed Stochastic Neighbor Embedding (t-SNE), was used to study the distinguishability between positive and negative samples, and explain the ML prediction performances. This work demonstrates that ML can be a generalized effective approach to process signals and dataset of biosensors dependent on resonant modes as biosensing mechanism.

Recent developments in optical biosensors based on integrated photonic devices are reviewed with a special emphasis on silicon-on-insulator ring resonator. The review is mainly devoted to the following aspects: (1) Principles of sensing mechanism, (2) sensor design, (3) biofunctionalization procedures for specific molecule detection and (4) measurement set-ups and advances in chip-integration. The inherent challenges of implementing photonics-based biosensors to meet specific requirements of applications in medicine, food analysis, and environmental monitoring are discussed.