Human serum albumin (HSA) corona formation at polymer microparticles of a spheroidal shape was studied using dynamic light scattering and laser Doppler velocimetry (LDV). Physicochemical characteristics of the albumin comprising, the zeta potential and the isoelectric point were determined as a function of pH for various ionic strengths. Analogous characteristics of the polymer particles were carried out. The adsorption of albumin on the particles was monitored by electrophoretic mobility measurements (LDV). The stability of the HSA functionalized particle suspensions under various pHs and their electrokinetic properties were determined. The deposition kinetics of the particles on mica, silica and gold sensors were determined in situ by optical microscopy, AFM and by the quartz microbalance (QCM) under diffusion and flow conditions. The obtained results were interpreted in terms of the coarse-grained random sequential adsorption model that allowed to estimate the range of applicability of QCM for determining deposition kinetics of virus and bacteria at abiotic surfaces.

Alkaline and alkaline-thermal activation were used in an attempt to synthesize zeolites using the sedimented illite fraction of raw Devonian clays from the Kuprava clay pit in Latvia. The Si/Al molar ratio of these clays is 2.79. Thermal and hydrothermal treatments were conducted using 6M and 10M NaOH solutions, along with different curing environments. The treated samples were analyzed using XRD, FTIR, and SEM, and were compared to the raw and calcined illite fraction samples. The main phase that forms after alkaline treatment is hydrosodalite (Na8[AlSiO₄]₆(OH)₂∙2H₂O). Using a higher concentration of NaOH leads to a significant increase in hydrosodalite formation. Increasing the curing temperature from 120°C to 600°C slightly reduces hydrosodalite formation due to the crystallization of the nepheline (Na₃K(Al₄Si₄O₁₆)) phase. This phase forms relatively intensively when the chemically treated samples are cured in a nitrogen environment at 600°C, thereby reducing the formation of hydrosodalite. The characteristic layered-fused structure of clay minerals remains in all chemically treated samples when cured at 600°C in air, but it does not remain when cured at the same temperature in nitrogen. The intensive formation of hydrosodalite is mainly achieved through hydrothermal treatment, along with a primary treatment using 10M NaOH. Considering the calculated size of the crystallites, treatment with 6M NaOH and curing at 120°C can also be seen as beneficial for hydrosodalite formation.

Refractory materials are used worldwide in process equipment. However, gaseous and liquid process products penetrate the surface layer, and deep into the volume of refractories destructing rather expensive constructions complicated to repair. To address this challenge, there is a need to develop protective coatings for refractory that can limit the penetration of working media and extend their operational lifespan. In this work, the application of gas-dynamic cold spraying (CGDS) to produce a coating on the refractory using fine titanium dioxide (TiO2) particles is explored. These particles are accelerated within a nitrogen flow, passing through a Laval nozzle, and then sprayed onto a fireclay surface. The mechanisms of particle deposition and layer formation on porous surfaces through experiments and numerical simulations were investigated. The geometry of a typical refractory pore was determined, which was then incorporated into Computational Fluid Dynamics (CFD) simulations to model the cold spraying process of porous substrates. As a result, the influence of the particle size on its velocity and angle of penetration into pores was established. Experimental findings demonstrate the effective closure of pores and the formation of a particle layer on the refractory surface. Furthermore, the nanoindentation tests for the refractory samples showcase capabilities for checking coating thickness for porous materials.

The rheological properties of a polyamide (PA) resin with low crystallinity were modified by melt-mixing it with a small amount of an alternative a-olefin–maleic anhydride copolymer as a reactive compound. Because PA has a low melting point, rheological characterization was performed over a wide temperature range. Owing to the reaction between PA and the alternative a-olefin–maleic anhydride copolymer, the blend sample behaved as a long-chain branched polymer in the molten state. The thermo-rheological complexity was obvious owing to large flow activation energy values in the low modulus region. The primary normal stress difference under steady shear was greatly increased in the wide shear rate range, leading to a large swell ratio at capillary extrusion. Furthermore, strain hardening in the transient elongational viscosity, which is responsible for favorable processability, was clear. Because this is a simple modification method, it will be widely employed to modify the rheological properties of various polyamide resins.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

This study investigates the impact of blade shape, stirring speed, and stirring time on the performance of lost foam casting coatings, specifically focusing on their viscosity, coating weight, and surface morphology. Commercially available lost foam coating materials were used, with varying blade shapes employed in high-speed dispersers. The effects of different stirring speeds and durations on coating viscosity and coating weight were systematically analyzed. It was observed that blade shape significantly influences the uniformity and performance of the coating. Among the blade shapes tested, the three-blade configuration demonstrated the highest efficiency in achieving uniform mixing, with optimal viscosity and coating weight. Stirring speed was found to have a minor effect on viscosity but a notable impact on coating weight, with speeds of 800 to 1200 rpm producing consistent results. Stirring time was shown to stabilize viscosity and coating weight after reaching a certain duration, beyond which no significant changes were observed. Drying behavior was analyzed at various temperatures, revealing that higher temperatures led to increased surface roughness and more pronounced cracks.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

Polarimetry is used to determine the Stokes parameters of a laser beam. Once all four S0,1,2,3 parameters are determined, the state of polarisation is established. Upon reflection of a laser beam with the defined S polarisation state, the directly measured S parameters can be used to determine the optical properties of the surface, which modified the S-state upon reflection. Here, we demonstrate polarimetry for the determination of surface anisotropies related to birefringence and dichroism from different materials, which have a common feature of linear patterns of different alignments and scales. It is shown that polarimetry in the back-reflected light is complementary to ellipsometry and four-polarisation camera imaging.

Background: Nowadays investigations in the field of dental implants engineering are focused on bioactivity and osseointegration properties.Objective: In this study, the oxide-covered titanium was functionalized by vitamin D3 molecules via a simple self-assembly method with the aim to design more corrosion resistant and at the same time more bioactive surface.Methods: Surface properties of the D3-coated titanium were examined by scanning electron microscopy, attenuated total reflectance Fourier transform infrared spectroscopy, and contact angle measurements, while a long-term corrosion stability during immersion in an artificial saliva solution was investigated in situ by electrochemical impedance spectroscopy.Results: Results of all techniques confirmed a successful formation of the D3 vitamin layer on the oxide-covered titanium. Besides very good corrosion resistivity (~5 MΩcm² ) the D3-modified titanium surface induced spontaneous formation of biocompatible bone-like calcium phosphates (CaP).Conclusion: Observed in vitro CaP-forming ability as a result of D3-modified titanium/artificial saliva interactions could serve as a promising predictor of in vivo bioactivity of implant materials.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

This study aimed to develop multifunctional nanoplatforms for both cancer imaging and therapy using superparamagnetic iron oxide nanoparticles (SPIONs). Two distinct synthetic methods, reduction-precipitation (MR/P) and co-precipitation at controlled pH (MpH), were explored, including the assessment of coating’s influence, namely dextran and gold, on their magnetic properties. These SPIONs were further functionalized with gadolinium to act as dual T1/T2 contrast agents for magnetic resonance imaging (MRI). Parameters such as size, stability, morphology, and magnetic behavior were evaluated by a detailed characterization analysis. To assess their efficacy in imaging and therapy, relaxivity and hyperthermia experiments were performed, respectively. The results revealed that both synthetic methods lead to SPIONs with similar average, 9 nm. Mössbauer spectroscopy indicated that samples obtained from MR/P consist of approximately 11-13% of Fe present in magnetite, while samples obtained from MpH have higher content, of 33%-45%. Despite coating and functionalization, all samples exhibited superparamagnetic behavior at room temperature. Hyperthermia experiments showed increased SAR values with higher magnetic field intensity and frequency. Moreover, the relaxivity studies suggested potential dual T1/T2 contrast agent capabilities for the coated SPpH-Dx-Au-Gd sample, thus demonstrating its potential in cancer diagnosis.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

As urbanization continues to increase, key conservation areas like World Heritage sites are being altered. This transformation is a cause for concern as it threatens the Outstanding Universal Value of these sites. To address this issue, a research question was formulated: How urban is World Heritage? The research focused on identifying and monitoring urbanization in heritage core zones listed on the World Heritage by tracking changes in built-up areas from 1985 to 2015. The findings revealed that urban developments, including housing, transport infrastructure construction, visitor accommodation facilities, and land conversions, have significantly impacted heritage properties. More than a third (37\%, 426) of the cultural heritage properties reported urban development, with the highest occurrences in Europe, North America, Asia, and the Pacific. Furthermore, these regions also displayed the highest rate of change per year between 1985 and 2015. This indicates the urgent need to identify and monitor the urbanization of World Heritage to preserve their OUV amidst increasing urban development.

Aloe vera is well known for its biological properties as a bioflavonoid-anti-inflammatory, antibacterial agent. It has been used frequently in the food sector as food coating for its hygroscopic properties and as an ingredient in the lucrative industry. Studies have also included Aloe vera as an eco-friendly green solution based on these properties. The current research focuses on the use of Aloe vera gel in printing pastes as an alternative sustainable solution to synthetic thickeners, evaluating its wet performance and ease of fabric stitching, and has been inspired by studies that similarly used this substance measuring its effect on the fabric's coefficient of friction and antimicrobial action. In the current study, printing pastes with natural colourants and Aloe vera gel thickener derived from natural leaves from Crete increased the fabric's mechanical resistance to abrasion compared to the untreated pastes. The measured performance did not differ substantially from prints with traditional synthetic pastes, hence tolerating the substitution with the non-contaminant variant. The enhanced resistance to abrasion and wear prolongates the fabric's serviceable life and resulting garments, decreasing the need for high industry processing volumes and, as a result, reducing pollution. The resistance to wear was evaluated using the dominant method in textile testing of the Martindale apparatus, which measured the cycles to failure, weight loss, and general appearance deterioration using the official photographic standards.

Nanocellulose (CNC) seems to be a promising surfactant, which, together with expandable graphite (EG), forms the essence of an effective natural-based fire retardant wood coating. In our research, the most suitable composition of the mixture was tested concerning good solubility, dispersion, and consistency. Favorable results were achieved with the formulation composed of a 4% CNC alkaline solution with 80 wt.% of selected EG. Subsequently, six different EG were used to prepare these wood fire retardant coatings. The effectiveness of treatments was verified using a test with a radiant heat source, where the test samples' relative weight loss, relative burning rate, and surface temperature during 600 sec were evaluated. All prepared formulations can be characterized as more or less equally effective. However, the best results were obtained with EG of GG 200 – 100 N, where the mass loss of the sample was 8.10 ± 1.24%. Very good results were also achieved by graphite 25 E + 180 HPH (8.70 ± 0.89%), which is similar to the previous one, even according to the microscopic assessment of the coating as well as the expanded layer. Graphite type 25 K + 180 (8.86 ± 0.65 %) shows the expanded layer's best cohesion, coating uniformity, and ease of application. The results of this work confirmed that the CNC coating itself has significant retardation effects.

Organic electrophoretic coatings have gained significant attention due to their ability to provide a uniform and controlled coating thickness, high coating adhesion, and excellent corrosion protection properties. In this work, to investigate the aging behaviors of an organic electrophoretic coating for magnesium alloys, water absorption kinetics curves of the coatings after immersion in 3.5 wt.% NaCl at 20℃ and 40℃ were measured, and parameters such as the saturated water absorption and saturation time of the free film coatings were fitted to determine the densification evolution of the organic coatings. A tensile test was used to test the tensile strength of the organic coating during service to determine the evolution of the strength and toughness of the organic coating. The evolution of wet adhesion of organic coatings with service time was tested by ASTM D4541-02. The impedance spectra of the organic coatings under the above conditions were detected by EIS, and finally, the failure behavior of the organic coatings under immersion was analyzed.

This study explores the effects of powder-to-liquid ratio on the performance characteristics of lost foam casting coatings. The investigation focuses on how variations in this ratio affect key properties including apparent viscosity, shear thinning behavior, coating weight, and surface morphology. Through a series of controlled experiments, coatings were prepared with different powder-to-liquid ratios and assessed for their physical and application properties. The results indicate that increasing the powder-to-liquid ratio raises the apparent viscosity and modifies shear thinning behavior. Notably, ratios exceeding 2.0 result in a sharp increase in viscosity that impedes coating application. The optimal powder-to-liquid ratio was determined to be between 2.0 and 2.2, where coatings demonstrated enhanced uniformity, improved particle distribution, and superior surface morphology. Coating weight increased up to a ratio of 2.2 but decreased beyond this threshold due to excessive viscosity. Both microscopic and macroscopic analyses confirmed that a ratio of 2.0 to 2.2 strikes the best balance for coating performance. These findings underscore the importance of precise powder-to-liquid ratio control to optimize the quality of lost foam casting coatings, offering valuable insights for refining coating formulations and application techniques in industrial contexts.

The unique structure of G4.0 PAMAM dendrimers allows the drug to be enclosed in internal spaces or immobilized on the surface. In the conducted research, the conditions for the formation of the active G4.0 PAMAM complex with doxorubicin (DOX) were optimized. The physicochemical properties of the system were monitored using DLS, CD, and fluorescence spectroscopy. The QCM-D method was chosen to determine the preferential conditions for the complex formation. The highest binding efficiency of the drug to the cationic dendrimer was observed under basic conditions when the DOX molecule was deprotonated. The decrease in the zeta potential of the complex confirms that DOX immobilizes through electrostatic interaction with the carrier's surface amine groups. The binding constants were determined from the fluorescence quenching of the DOX molecule in the presence of G4.0 PAMAM. The two-fold way of binding doxorubicin in the structure of dendrimers was visible in the ITC isotherm. Fluorescence spectra and release curves identified reversible binding of DOX to the nanocarrier. Among the selected cancer cells, the most promising anticancer activity of G4.0-DOX was observed in A375 malignant melanoma cells. Moreover, the preferred intracellular location of the complexes concerning the free drug was found, which is important from a therapeutic point of view.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Many protein expression systems are primary utilised to produce a single, specific recombinant protein. In contrast, most biological processes such as virus assembly rely upon a complex of several interacting proteins rather than the activity of a sole protein. The high complexity of the baculovirus genome, coupled with a multiphase replication cycle incorporating distinct transcriptional steps, made it the ideal system to manipulate for high-level expression of a single or co-expression of multiple foreign proteins within a single cell. We have developed and utilised a series of recombinant baculovirus systems to unravel the sequential assembly process of a complex non-enveloped model virus, Bluetongue virus (BTV). The high protein yields expressed by the baculovirus system not only facilitated structure-function analysis of each viral proteins but were also advantageous to crystallography studies and supported the first atomic level resolution of a recombinant viral protein, the major BTV capsid protein. Further, the formation of recombinant double-shelled virus-like particles (VLPs) provided insights into the structure-function relationships among the four major structural proteins of the BTV whilst also representing a potential candidate for a viral vaccine. The baculovirus multi-gene expression system facilitated the study of structurally complex viruses (both non-enveloped and enveloped viruses) and heralded in a new generation of viral vaccines.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

This paper presents and demonstrates the development of a new lightweight coating for aluminium alloy using a novel multicomponent alloy based on the AlSiMgCu system. This coating was applied using a newly designed approach that combined High-Velocity Oxy-Fuel (HVOF) and Plasma Spraying processes. This hybrid technique enables the deposition of coatings with enhanced performance characteristics. The microstructure was studied using optical microscopy (OM) and scanning electron with energy dispersive X-ray spectroscopy (SEM+EDS) microscopy, revealing good adhesion and compaction between the multicomponent coating and the A6061 substrate with 50 to 150 µm thickness. Vickers indentations were performed on the substrate and the new coating material, revealing a 50% improvement in the material's hardness compared to the casted alloy. Additionally, electrical conductivity measurements showed approximative x3.3 times values compared to the alloy in as-cast condition due to high solidification rates altering the morphology of the phases. Corrosion tests demonstrated a lower corrosion rate compared to other multicomponent aluminium alloys and similar to thermal treated A6061 alloy. Finally, tribological results obtained using ball on disc (BOD) test and laser scanning confocal microscopy, confirmed that the new multicomponent coating exhibited reductions in both friction coefficient and wear rate by more than 20% and 50%, respectively. This study demonstrates that using multi-component aluminium coatings could lead to developing of new automotive parts with enhanced properties for corrosion resistance, electrical conductivity, and wear conditions. Optimizing the thermal spraying parameters could further enhance the coating, achieving greater and more homogeneous thicknesses and yielding even higher performance properties.

Acute and chronic respiratory diseases impose a significant economic and health burden. Distal small airway assessment requires invasive procedures such as a bronchoscopy and bronchoalveolar lavage. The Particles in Exhaled Air (PExA) device provides a non-invasive means of assessing small airways; it captures distal airway particles sized around 0.5-7m and contains particles of respiratory tract lining fluid (RTLF) that originate during airway closure and opening. The PExA device can measure particle count and mass according to particle size. Subsequent capture of particles in a thin membrane enables application of various analytical methods to assess a broad range of biomolecules including phospholipids, proteins, inflammatory profile, and other metabolites to characterise inflammation and diseases processes such as asthma, chronic obstructive pulmonary disease, acute respiratory distress syndrome, lung cancer, and more recently acute infections such as COVID-19. PExA analysis provides a promising alternative to traditional investigative methods in the assessment, diagnosis, and management of respiratory conditions. By evaluating specific biomarkers in the RTLF associated with airway inflammation, PExA may offer a more accurate and comprehensive understanding of the molecular-level changes in the small airways of patients with acute and chronic lung diseases.

Bioactive surface coatings have retained the attention of researchers and physicians due to their versatility and range of applications in orthopedics, particularly in infection prevention. Antibacterial metal nanoparticles (mNPs) are a promising therapeutic, with vast application opportunities on orthopedic implants. The current research aimed to construct a polyelectrolyte multilayer on a highly porous titanium implant using alternating thin film coatings of chitosan and alginate via the layer-by-layer (LbL) self-assembly technique, along with the incorporation of silver nanoparticles (AgNPs) or titanium dioxide nanoparticles (TiO2NPs), for antibacterial and osteoconductive activity. These mNPs were characterized for their physicochemical properties using quartz crystal microgravimetry with dissipation system, nanoparticle tracking analysis, scanning electron microscopy, and atomic force microscopy. Their cytotoxicity and osteogenic differentiation capabilities were assessed by AlamarBlue and alkaline phosphatase (ALP) activity assays, respectively. The antibiofilm efficacy of the mNPs tested against Staphylococcus aureus. The LbL polyelectrolyte coating was successfully applied to the porous titanium substrate. A dose-dependent relationship between nanoparticle concentration and ALP as well as antibacterial effects was observed. TiO2NP samples were also less cytotoxic than AgNP counterparts, although similarly antimicrobial. Together, these data serve as a proof-of-concept for a novel coating approach for orthopedic implants with antimicrobial and osteoconductive properties.

Cancer, characterized by abnormal cell proliferation driven by genetic mutations, remains a significant health challenge. Tailoring effective therapies depends on factors like tumor location, grade, and stage, alongside patient condition. Leveraging Nano-carrier encapsulated drugs offers a promising avenue, as they accumulate preferentially at tumor sites, enhancing therapeutic efficacy while mitigating side effects. Polymeric Nano-carriers, with their customizable properties, further optimize drug delivery efficiency and specificity. Incorporating active targeting ligands such as antibodies, carbohydrates, peptides, folates, and aptamers-onto polymeric nanoparticle surfaces through techniques like functionalization, adsorption, and conjugation plays a pivotal role in directing therapeutic agents to tumor cells. Consequently, polymeric nanoparticles emerge as the carrier of choice for delivering drugs to various tumor types, including breast, colon, lung, prostate, liver, and spleen tumors.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

In previous papers we have derived equations of motion with radiation terms and proved the existence-uniqueness of periodic solution of the 3-body problem of classical electrodynamics. The number of equations of motion – 12 is more than the number of unknown functions – 9. It turns out that 9 equations are independent and the rest 3 ones are consequences of them. These three equations have a solution and they give the expressions for the energy of the moving particles. The main goal of the present paper is to estimate the energy of rounding about the nuclei particles and compare it with the values given by quantum mechanics.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

If we assume that: a. The four fundamental forces of nature are independent waves without rest masses, and their speeds are constant in a vacuum, just like light. b. Light or electromagnetic waves and gravity are comparable in structures. Weak and strong interactions are similar in structures. c. Light and weak interaction have the same speed c_L with spin number +1 or –1. d. Gravity and strong interaction have the same speed c_G without spin. e. The primary particles, namely electrons, electron neutrinos, and dark neutrinos in this paper, are made by the above four waves. We can find and describe some fundamental characteristics of the primary particles (e.g., their sizes, energies, and interactions) and introduce new attractive results from them (e.g., the source of the Pauli exclusion principle, the solution to the Einstein-Podolsky-Rosen paradox, and c_G slightly faster than c_L).

Both grape pomace and whey are waste products from the food industry that are rich in valuable ingredients. The utilisation of these two by-products is becoming increasingly possible as consumer awareness of upcycling increases. The biological activities of grape pomace extract (GPE) are diverse and depend on its bioavailability, which is influenced by processes in the digestive system. In this work, goat whey protein (GW) was used as the primary coating to protect the phenolic compounds of GPE during the spray drying process. In addition, trehalose (T), sucrose (S), xylose (X) and maltodextrin (MD) were added to the goat whey proteins as co-coatings and protein stabilisers. All spray drying experiments resulted in microcapsules (MC) with high encapsulation efficiency (77.6—95.5%) and yield (91.5—99.0%) and almost 100% recovery of phenolic compounds during the release test. For o-coumaric acid, the GW-coated microcapsules (MC) showed a bioavailability index of up to 731.23%. A semi-crystalline structure and hydrophilicity are characteristics of the MC coated with 10% T, S, X or 5% MD. GW alone or in combination with T, S, MD or X has proven to be a promising carrier for polyphenols from grape pomace extract and ensures good bioavailability of these natural antioxidants.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Exploring for green and affordable protection of perishable fruit like cherry tomato is of significance. Here the protective efficacy and its underpinnings of coating with oleaster gum, alone or incorporated with cuminal, on cherry tomatoes stored at ambient temperature were investigated. The composite coating of oleaster gum with 0.1% cuminal reduced decay, respiration rate, weight loss, and softening of the fruit and decelerated their decreases of total soluble solids, titratable acidity, and soluble proteins, and therefore maintained their marketability. Furthermore, it reduced the accumulation of O•− 2and H2O2 in fruit, and mitigated cell membrane lipid oxidation and permeabilization, thereby retarding their senescence. Instrumentally, it elevated the activities of superoxide dismutase, catalase, peroxidase, and ascorbate peroxidase and the levels of ascorbic acid and glutathione. This potentiation of the fruit antioxidant system makes the composite coating a promising approach to keeping the postharvest quality of perishable fruit.

Organic Coatings have potential applications in the prevention of metal corrosion in an aqueous solution. The protective effect of SEBS coated copper corrosion in NaCl 3% solution was investigated by using electrochemical methods. The main objective of this work is to find the optimal conditions of the protocol immersion to evaluate the effects of SEBS ratio and two-immersion time on the anticorrosive behaviour of copper in 3 wt % NaCl solution in order to determine the best conditions to produce a protective SEBS film on the copper surface. Response Surface Methodology (RSM) is used as an optimization method. The study’s findings show the combination of three environmental factors that minimize corrosion rate. The Box-Behnken Design (BBD) is working perfectly for the statistical significance of the model (ANOVA test). This analysis calculates the contribution value of each parameter in changing the value of the corrosion rate (CR) in not only individual but also synergistic cases. The optimized parameters were found to be a 2.17% of SEBS ratio, 20 min of immersion 1, and 21 min of immersion 2. The electrochemical impedance spectroscopy tests confirmed the results.

The structure and physicochemical properties of polyvinyl alcohol (PVA) and PVA/glycerol films have been investigated by Fourier-transform infrared spectroscopy (FT-IR), X-ray Diffraction (XRD), thermogravimetry/differential thermal analysis (TG/DTA), and advanced scanning probe microscopy (SPM). In the pure PVA films, SPM allowed us to observe ribbon-shaped domains with a different frictional and elastic contrast, which apparently originated from a correlated growth or assembly of PVA crystalline nuclei located within individual PVA clusters. The incorporation of 1.0 wt.% glycerol led to modification in shape of those domains from ribbon-like in pure PVA to rounded in PVA/glycerol 1.0 wt.% films; changes in the relative intensities of the XRD peaks and a decrease of the amorphous halo in the XRD pattern were also detected, while the DTA peak corresponding to the melting point remained at almost the same temperature. For higher glycerol content, FT-IR revealed additional glycerol-characteristic peaks presumably related to the formation of glycerol aggregates, and XRD, FT-IR, and DTA all indicated a reduction in crystallinity. For more than 2.0 wt.% glycerol, the plasticization of the films complicated the acquisition of SPM images without tip-induced surface modification. Our study contributes to the understanding of crystallinity in PVA and how it is altered by a plasticizer such as glycerol.

Researchers have explored primary colour-geometric shape associations since Kandinsky's correspondence theory. However, there is a gap in the literature regarding interior colour applications on surface shapes. To address this gap, an online study was employed to gather data with one hundred participants who were asked to choose their preferred colours for shapes on bedroom walls with follow-up questions on the colour-shape semantic associations, their preference of colours and shapes on bedroom walls independently in addition to their favourite colour, their favourite shape, and colour-shape pairs without interior context. The results revealed that colour-shape preferences in interiors differ from those found in psychology studies, other colour applications on bedroom walls, and other preferences, indicating that colour preference is context-dependent. Interestingly, the most popular colour for surface shapes on bedroom walls is purple, followed by brown and blue. The study contributes to the existing literature by providing colour charts for bedroom applications for professionals in the industry, their clients/users, and future studies.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

Due to its potential harm to space payload, microwave corona breakdown of microstrip circuits has attracted much attention. This work describes an efficient way to suppress corona breakdown. Since corona breakdown threshold is determined by the highest electric field intensity at the surface of microstrip circuits, lacquer coating with thickness of tens of microns is sprayed on the top of microstrip circuits. The applied dielectric coating is used to move the discharge location away from circuit’s surface which is equivalent to reduce the highest electric field intensity on the in-terface of solid/air of the circuit and thus results into higher breakdown threshold. Two designs of classic coupled-line band-pass filter were used for verification. Corona experimental results at 2.5 GHz show that, in the interested low pressure range (100 to 4500 Pa), 5.3 dB improvement of mi-crowave corona breakdown threshold can be achieved for a filter with narrowest gap of 0.2 mm while its electrical performances like insertion loss, Q-factor are still acceptable. A threshold improvement prediction method is also presented and validated.

The samples from lunar farside have great significance for the study of the Moon, and even the solar system. Chang’e-6 landed successfully on the southern mare of the Apollo basin and returned ~2 kg samples from lunar farside. To provide a better understanding for the background of the returned samples, we conducted detailed crater size-frequency distribution (CSFD) measurements in the Chang’e-6 landing region, the southern mare of the Apollo basin. The southern mare is divided into western mare (W region) and eastern mare (E region), and then subdivided into five sub-units (W1, W2, W3, W4, W5) and three units (E1, E2, E3), respectively, according to the elevation, Ti and Fe abundances. Within the W2 and W5 region, more detailed sub-units were divided. The results show that the southern mare generally have two epochs, one of the Imbrian period and the other of the Eratothenian period. The basalt eruption lasted for ~1.7 Ga, from 3.28 Ga of the eastern mare to 1.54 Ga of the western mare. W region is younger than E region, while the three units of E region has an age of ~3.2 Ga. The ages of the western mare basalts range from 2.98 Ga to 1.54 Ga, lasting for 1.4 Ga. It’s worth noting that the age of the basalt at the Chang’e-6 sampling site is ~1.68 Ga, indicating the samples returned may include components with this very young age.

Sulfate, the main dissolved contaminant in acid mine drainage (AMD), is ubiquitous in watersheds affected by coal and metal mining operations worldwide. Engineered passive bioremediation systems (PBS) are low-cost technologies that remediate sulfate contamination by promoting (1) precipitation of sulfate-bearing compounds, such as schwertmannite and gypsum; and (2) microbially-mediated sulfate reduction (BSR) to sulfide with subsequent precipitation of sulfide minerals. In this study, chemical and sulfur isotopic data are used to infer multiple pathways for sulfate sequestration in the Tab-Simco PBS. By simultaneously monitoring sulfate concentrations and δ34SSO4 values at four sampling points across the PBS, we (1) identified that the organic layer within the bioreactor was the primary site of BSR processes contributing to sulfate sequestration; (2) observed seasonal variations of BSR processes; (3) estimated that initially the BSR processes contributed up to 30% to sulfate sequestration in the Tab-Simco bioreactor; and (4) determined that BSR contribution to sulfate sequestration continuously declined over the PBS operational lifetime. Together, our results highlight the utility of combining geochemical and microbial fingerprinting techniques to decipher complementary processes involved in sulfur cycling in a PBS as well as the value of adding the sulfur isotope approach as an essential tool to help understand, predict, prevent and mitigate sulfate contamination in AMD-impacted systems.

The study of the surface thermodynamic properties of solid materials is primordial for the determination of the dispersive surface energy, polar enthalpy of adsorption and Lewis’s acid base properties of solid particles. Inverse gas chromatography technique (IGC) at infinite dilution is the best surface technique for the determination of the surface physicochemical properties of materials. (1) Background: This paper was devoted to study the surface properties of solid materials such as alumina particles by using IGC technique. (2) Methods: Different methods and molecular models such as spherical, cylindrical, van der Waals, Redlich-Kwong, Kiselev and geometric models, were used to determine the London dispersive surface energy of solid surfaces. Hamieh model was also used and highlighted the thermal effect on the surface area of solvents. (3) Results: The variations of the dispersive surface energy and the free energy of adsorption were determined for alumina particles as a function of the temperature as well as their Lewis’s acid base constants. Alumina surfaces were proved to exhibit a strong Lewis amphoteric character three time more basic than acidic (4) Conclusions: The new methodology based on Hamieh model gave the more accurate results of the physicochemical properties of the particle surfaces.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

Different materials prepared by appropriate synthesis methods and applying different post syn-thesis processes could be used as hole transport layer in perovskite solar cells. In the present work annealing was employed to enhance physical properties of copper oxide (CuO) thin films fabricated via spin coating technique and the effects of annealing on their optical, morphological, electrical and structural properties were investigated. The XRD findings revealed the polycrystalline structure with large crystallite size. Optical spectra showed larger transmission beyond the visible region, reduced absorption, and a decrease in bandgap energy from 1.93 eV to 1.81 eV. The Ag phonon modes at 299.22 and 304 cm-1 shown by the Raman shift confirmed the development of the CuO pure phase. FTIR spectra showed the Cu-O stretching band at 759, 764 and 446 cm−1. SEM revealed the agglomeration of nano crystallites with large grains on the surface. The carrier type conductivity of annealed CuO thin films was determined via two-point hot probe technique. Low resistivity values were determined via four-point probe method. These findings indicate that CuO thin films may be successfully used as a companion with an n-type layer in p-n junction solar cells, and a hole transport layer in perovskite solar cells.

The amount of solar energy produced is directly proportional to the surface area of solar panels exposed to sun rays. To increase the productivity of solar panels, a number of techniques are proposed by curving the surface or protruding the panel surface to maximise the surface area, e.g. Protruding panel surfaces with shapes such as pyramidal, cone, spherical cap, sinusoidal wavy curve, etc. These techniques are analysed to determine whether the panel surface area increases. The geometrical design analysis showed that, depending on the chosen surface curving method, the panel can achieve a remarkable increase in surface area.The system advisor model was used to assess a sample of solar cells with standard measurements of 6 by 6 inches that were organised in a zigzag pattern with different angles of inclination (10°, 15°, 20°, 25°, 30°, and 35°). Overall, the maximum power pump and annual AC energy performance increase by 1.4%, 4.2%, 6.8%, 10.8%, 14.9%, and 21.6%, respectively, over a one-year period of productivity. However, by applying the concept of solar panel efficiency degradation due to tilting solar panels at an angle by Mamun et al. (2022), for each 5° increase in tilt angle beyond the ideal 10°, the efficiency decreases by approximately 0.76%. In conclusion, the overall efficiency is greater than that of standard flat solar panels, provided the tilt angle is within a reasonable range.

The properties of coatings obtained using two surface preparation methods were compared: heating and etching by ion bombardment with plasma generation by arc evaporators and heating and etching by a glow discharge. A Ti-TiN-(Ti,Cr,Al)N coating was deposited. The use of a glow discharge provides better resistance of the coating to destruction during the scratch test and wear resistance of metal-cutting tools when turning steel. As the cutting speed increases, the advantage in wear resistance of the coating deposited using a glow discharge increases. During the process of heating and etching by ion bombardment with metal ions, a nanolayer rich in cobalt and tooling elements (iron, molybdenum) is formed in the area of the interface of the coating and the carbide substrate. When heated and etched by a glow discharge, such a layer does not form. When using both methods, there is identical diffusion of tungsten into the coating and diffusion of chromium and possibly titanium into the substrate. Thus, the glow discharge heating and etching method can be effectively used in the process of PVD coating deposition.

The infrared (IR) satellite remote sensing of sea surface skin temperature (SSTskin) is challenging in the northern high latitude region, especially in the Arctic because of its extreme environmental conditions, and thus the accuracy of SSTskin retrievals is questionable. Several Saildrone uncrewed surface vehicles were deployed at the Pacific side of the Arctic in 2019, and two of them, SD-1036 and SD-1037, were equipped with a pair of IR pyrometers on the deck whose measurements have been shown to be useful in the derivation of SSTskin with sufficient accuracy for scientific applications, providing an opportunity to validate satellite SSTskin retrievals. This study aims to assess the accuracy of MODIS-retrieved SSTskin from both Aqua and Terra satellites by comparisons with collocated Saildrone-derived SSTskin data. The mean differences in SSTskin from the SD-1036 and SD-1037 measurements are different by ~0.4 K, largely resulting from differences in the atmospheric conditions experienced by the two Saildrones. The performance of MODIS on Aqua and Terra in retrieving SSTskin is comparable. Negative brightness temperature (BT) differences between 11 μm and 12 μm channels are identified as being physically based, but are removed from the analyses as they present anomalous conditions for which the atmospheric correction algorithm is not suited. Overall, the MODIS SSTskin retrievals show negative mean biases, -0.234 K for Aqua and -0.295 K for Terra. The variations in the retrieval inaccuracies show an association with diurnal warming events in the upper ocean from long periods of sunlight in the Arctic. Also contributing to inaccuracies in the retrieval is the surface emissivity effect in BT differences characterized by the Emissivity-introduced BT difference (EΔBT) index. This study demonstrates the characteristics of MODIS-retrieved SSTskin in the Arctic, at least at the Pacific side, and underscores that more in situ SSTskin data at high latitudes are needed for further error identification and algorithm development of IR SSTskin.

Titanium alloys belong to the metal biomaterials that are one of the most widely used in medicine. In recent years, in order to reduce the use of vanadium, Ti6Al4V alloy is increasingly replaced by Ti6Al7Nb alloy. In addition, to ensure the best possible biocompatibility, its surface is subjected to appropriate modifications, for example, anodic oxidation. Despite the extensive use of anodic oxidation of titanium implants in orthopedics, there are few works focused on a detailed analysis of the chemical composition of the surface layers. In addition, the effect of treatments before anodic oxidation on the properties of the produced layer has not been analyzed. Thus, the purpose of this study was to analyze in detail the chemical composition of the passive layer of Ti6Al7Nb alloy obtained by anodic oxidation preceded by sandblasting. Moreover, the physicochemical properties of the analyzed surface affecting biocompatibility were determined. For this purpose, surface observation, wettability and roughness tests, microhardness tests, electrochemical tests and phase composition analysis were carried out. In addition, the preclinical suitability, of the surface modified in this way, was evaluated by cytotoxicity tests.

The superconductivity of CaC6 as a function of pressure and of abundant Ca isotopes is revisited using DFT calculations on a 2c – double hexagonal superlattice. The introduction of superlattices is motivated by previous synchrotron absorption and Raman spectroscopy results on other superconductors that show evidence of superlattice vibrations at low (THz) frequencies. A 2c superlattice for CaC6 is illustrative of atomic orbital symmetry and periodicity, including bonding and antibonding s-orbital character implied by cosine modulated electronic bands. Inspection of the cosine band reveals that the cosine function has a small (meV) energy difference between bonding and antibonding regions relative to a midpoint non-bonding energy. Fermi surface nesting is apparent in an appropriately folded Fermi surface using a superlattice construct. Nesting relationships identify phonon vectors for conservation of energy and for phase coherency between coupled electrons at opposite sides of the Fermi surface. Detailed analysis of this Fermi surface nesting provides accurate estimates of the superconducting gaps for CaC6 with change in applied pressure. Recognition of superlattices within a rhombohedral or hexagonal representation provides consistent mechanistic insight on superconductivity and electron−phonon coupling in CaC6.

MCrAlYHf bond coats are employed in jet and aircraft engines, stationary gas turbines, and power plants, which require strong resistance to oxidation at high temperatures. The oxidation behavior of a free-standing CoNiCrAlYHf coating was investigated in this study. Isothermal oxidation tests were performed in air at 1050 °C on the specimens with various levels of surface roughness to investigate the oxidation kinetics. X-ray diffraction, focused ion beam, scanning electron microscopy (SEM), and scanning transmission electron microscopy were used to characterize the surface oxides. The surface roughness was examined using a contact profilometer and SEM. An empirical model was proposed to elucidate the impact of surface roughness on the oxidation behavior based on the correlation between the surface roughness level and oxidation rates.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

Strip steel surface defect recognition research has important research significance in industrial production. Aiming at the problems of defect feature extraction difficulty, slow detection speed and insufficient dataset, YOLOv5 is improved on the basis of YOLOv5, and YOLO-LFPD (Lightweight fine particle detection) model is proposed. By introducing the RepVGG (Re-param VGG) module, the robustness of the model to the surface defect features of strip steel is enhanced, and the expressive ability of the model is improved. FasterNet is used to replace the backbone network, which ensures the accuracy and accelerates the inference speed, making the model more suitable for real-time monitoring. The use of pruning, GA genetic algorithm with OTA loss function method further reduces the model size while better learning the strip steel defect feature information, thus improving the generalisation ability and accuracy of the model. The experimental results show that the introduction of the RepVGG module and the use of FasterNet can well improve the model performance, with a reduction of 48% in the number of parameters, a reduction of 13% in the number of GFLOPs, an inference time of 77% of the original, and an optimal accuracy compared with the network models in recent years. The experimental results on the NEU-DET dataset show that the accuracy of YOLO-LFPD is improved by 3% to 81.2%, which is better than other models, and provides new ideas and references for the lightweight strip steel surface defect detection scenarios and application deployment.

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

Medical imaging is an active field of research that fosters the necessity for novel multimodal imaging probes. In this line, nanoparticle-based contrast agents are of special interest, since those can host functional entities either within their interior, reducing potential toxic effects of the imaging tracers, and on their surface, providing high payloads of probes, due to their large surface-to-volume ratio. The long-term stability of the particles in solution is an aspect usually under-tackled during probe design in research laboratories, since their performance is generally tested briefly after synthesis. This may jeopardize a later translation into practical medical devices, due to stability reasons. To dig into the effects of nanoparticle aging in solution, respect to their behavior in vivo, iron oxide stealth nanoparticles were used at two stages (3 weeks vs. 9 months in solution), analyzing their biodistribution in mice. Both sets of nanoprobes showed similar sizes, zeta potentials and morphology, as observed by DLS and TEM but, fresh nanoparticles accumulated in the kidneys after systemic administration, while aged ones accumulated in liver and spleen, confirming an enormous effect of particle aging on their in vivo behavior, despite barely noticeable changes perceived on a simple inspection of their structural integrity.

In this study, we investigated the surface modification of LiNi1/3Co1/3Mn1/3O2 cathode material by coating it with ZnO and examined the changes in surface composition using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, we investigated the electrochemical properties, including discharge capacity and initial irreversible capacity, of the modified materials. The results revealed that ZnO predominantly existed on the material surface, exerting influence on both surface composition and electrochemical characteristics. As the ZnO coating amount increased, the nickel and manganese content on the material surface also increased, and heat treatment at 400 °C resulted in the formation of composite oxides of transition metals and zinc on the material surface. The bonding energy of transition metals increased, and ZnO coating at a mass fraction of 2 % effectively suppressed irreversible reactions around 3.6 V at 55 °C, thereby improving initial coulombic efficiency. Battery materials coated with 2% ZnO exhibited optimal discharge capacity and cycle life at 55 °C/0.5 C.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

It is shown that if there exists in nature a pair of heavy elementary particles each with a charge equal to that of the proton and with mass energy , then their direct interaction gives rise to a spontaneous fractionation of the two charges into three pairs of elementary particles according to two equiprobable channels, one hadronic and one leptonic. The leptons and quarks produced are in agreement with the first generation of the Standard Model of matter. Fractionation suggests the relative abundances of the elementary particles, introducing some questions about the possibility of the real existence of a currently unknown particle and its role in the formation of an apparent matter-antimatter asymmetry in the universe.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

Following technological advances, autonomous and remote-controlled ships are performing trials in some sea areas; a mandatory goal-based MASS code, expected to enter into force on 1 January 2032, is under discussion in the International Maritime Organization (IMO). However, there are no unified standards regarding verification methods to define operating limitations for cutting-edge technologies, which are expected to be elements of MASS, so it is difficult to assess the risk factors for the management and operation of MASS. This paper outlines the regulatory framework for MASS, followed by a discussion of its application, considering the differences between MASS and automated driving, and how to develop safety management and operation using standards for automated driving. A requirements management framework developed as a system and software engineering standards to build safety management and operation of MASS is proposed. It is also suggested that the requirements management framework could be used not only for MASS development but also for regulatory review from a requirements management view.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

The surface characterization of indium tin oxide (ITO) films was processed by oxygen (O2) plasma gas using a magnetron sputtering method of varying O2-plasma gas from 20 sccm to 100 sccm for potentially fostering in electronic devices applications on dye-sensitize solar cells (DSSC) in this work. In order to gain an outstanding performance rate with high-quality thin films, the affect of correlation between the electrical, optical, and morphology properties was significantly investigated. Clearly, the content of investigation exhibited that the films properties was changed by variation of the gas composition. These changes have contemporary relevance to the sputtering gas during the deposition process. To conclude, the greatest electrical properties was displayed by O2 -plasma gas flow rate of 20 sccm, which showed the lowest resistivity. In addition to this, the final products were practically fabricated to active layers for dye-sensitize solar cells (DSSC) applications. The highest efficiency of DSSC device was indicated of approximately 0.35% which was located by 40 sccm of the O2-plasma gas. Consequently, the study could be a possibility way of preparing ITO thin films with improved special properties of substantial applications for solar cells devices in the near future.

MgAl oxide coatings containing MgO and MgAl2O4 phases were doped with CeO2 particles using plasma electrolytic oxidation (PEO) of AZ31 magnesium alloy in 5 g/L NaAlO2 water solution, with CeO2 particles added at concentrations up to 8 g/L. They underwent extensive inve-stigation into their morphology, chemical and phase compositions, and most importantly, photoluminescent (PL) properties and photocatalytic-activity (PA) in photodegradation of methyl orange (10 cm3 of 8 mg/L). The concentration of CeO2 particles in the aluminate electrolyte influences the amount of CeO2 particles incorporated into MgAl oxide coatings, but CeO2 particles have no signi-ficant effect on the surface morphology, thickness, or phase structure of the coatings. The PL emi- ssion spectrum of MgAl oxide coating is divided into two bands: one in the 350-600 nm range related to structural defects in MgO, and another much more intense in the 600-775 nm range attributed to F+ centres in MgAl2O4. Incorporated CeO2 particles do not have a significant effect on the PL intensity of the band in the red spectral region, but the PL intensity of the first band increases with the concentration of CeO2 particles. PA of MgAl/CeO2 oxide coatings is higher than that of pure MgAl oxide coatings. The highest PA was observed for MgAl/CeO2 oxide coatings formed in aluminate electrolytes with the addition of 2 g/L of CeO2 particles. The MgAl/CeO2 oxide coatings remained chemically and physically stable across multiple cycles, indicating their potential for applications.

Aim: The purpose of this study is to evaluate the remineralization potential of primary teeth enamel after being exposed to different laser diode therapy. Methods: Ninety-six vestibular primary teeth enamel samples were divided into eight groups (n=12) with varying treatments: control (G1), CPP-ACP-fluoride varnish (G2), diode lasers at 980 nm (G3), 808 nm (G4), 450 nm (G5), 980 nm + CPP-ACP-fluoride varnish (G6), 808 nm + CPP-ACP-fluoride varnish (G7), and 450 nm + CPP-ACP-fluoride varnish (G8). Each sample was assessed using DIAGNOdent® at baseline, post-treatment, and post-pH cycle re-mineralization. SEM imaging was performed before and after treatment and following the pH cycle. Results: The results indicated that the 980 nm and 808 nm diode lasers, both alone and in combination with CPP-ACP-fluoride varnish, either maintained or increased the calcium (Ca) weight percentage (Wt%) in the enamel. The 980 nm diode laser combined with CPP-ACP-fluoride varnish (G6) showed a significant increase in Ca Wt%, suggesting a strong remineralization effect. Similarly, the 808 nm diode laser alone (G4) also promoted a substantial increase in Ca Wt%. In contrast, the 450 nm diode laser, whether applied alone or in combination with CPP-ACP-fluoride varnish, resulted in a lower Ca Wt% and an increase in phosphorus (P) Wt%. Most groups, except for the CPP-ACP-fluoride varnish alone (G2), demonstrated an increase in P Wt%, indicating a complex interaction between laser therapy and enamel remineralization. Conclusions: The combined use of laser therapy with CPP-ACP-fluoride varnish significantly enhanced the remineralization of temporary teeth enamel. The 980 nm diode laser + CPP-ACP-fluoride varnish showed the most pronounced improvement in remineralization, while the 808 nm diode laser alone also effectively increased calcium solubility. These findings suggest that higher wavelength diode lasers, particularly when combined with remineralizing agents, can effectively enhance the mineral content of primary teeth and promote enamel remineralization.

Particles are considered temporarily identical if the interchange of these particles does not cause any observable physical effects within a time interval Δt. An indistinguishability hypothesis is proposed for such particles, suggesting that two particles (or systems) with nearly the same degree of internal freedom will actually interchange under certain circumstances, thereby affecting the subsequent dynamics. This indistinguishability implies that, theoretically, it is possible to capture an elementary particle with extraordinarily large internal freedom by trading it for an isolated composite system of ordinary matter particles with almost the same total internal freedom as the large-freedom particle. Following this, the ordinary particles will instantly disperse into the environment, while the large-freedom particle will initially be captured and then gradually delocalized into the environment, an observable phenomenon. If this hypothesis is proven true in the future, it might provide a novel strategy for detecting dark matter particles.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

Identifying locations of landslide slip surfaces provides critical information for understanding the volume of landslides and the scale of disasters, which is essential for formulating disaster preparedness and mitigation strategies. Based on hydrogeological survey data from 24 deep-seated landslide-prone sites in Taiwan's mountainous regions, this study first developed the hydraulic conductivity potential index (HCPI) using principal component analysis to quantify hydraulic properties of disturbed rock formation with six geological factors. Then, The regression analysis was performed to construct a permeability estimation model for the geological environment of landslides. Finally, the established model was utilized to develop an identification method for potential slip depths in landslide-prone sites. Results indicated a strong relation between HCPI and hydraulic conductivity with a determination coefficient of 0.895. The relation equation confirmed that its generated data concerning the depths of significant changes in hydraulic conductivity could be used to identify potential slip surfaces. Additionally, this study successfully establishes a rule for identifying potential slip zones by summarizing data concerning the generated hydraulic conductivity profiles, stratigraphic lithology, existing inclinometer slip depth records, and groundwater level of landslide sites. This identification method was then applied to predict potential slip depths for ten landslide sites where slip surfaces have not yet occurred. These findings offer a new alternative to having early information on potential sliding depths for timely disaster management and control implementation.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Paper presents proposition of possible extension of The Standard Model Classification of Particles and Fields in way to include gravitation into it.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

The urbanization effects on land surface phenology (LSP) have been investigated by many studies, but few studies focused on the temporal variations of urbanization effects on LSP. In this study, we used the MODIS EVI, MODIS LST data and China’s Land Use/Cover Datasets (CLUDs) to investigate the temporal variations of urban heat island intensity and urbanization effects on LSP in Northeast China during 2001–2015. Land surface temperature (LST) and phenology differences between urban and rural areas represented the urban heat island intensity and urbanization effects on LSP, respectively. Mann-kendall nonparametric test and Sen's slope were used to evaluating the trends of urbanization effects on LSP and urban heat island intensity. The results indicated that the average land surface phenology (LSP) during 2001–2015 was characterized by high spatial heterogeneity. The start of the growing season (SOS) in old urban area had become earlier and earlier than rural area and the differences of SOS between urbanized area and the rural area changed greatly during 2001–2015 (−0.79 days/year, p < 0.01). Meanwhile, the length of the growing season (LOS) in urban and adjacent areas had become increasingly longer than rural area especially in urbanized area (0.92 days/year, p < 0.01), but the differences of the end of the growing season (EOS) between urban and adjacent areas did not change significantly. Next, the UHII increased in spring and autumn during the whole study period. Moreover, the correlation analysis indicated that the increasing urban heat island intensity in spring contributed greatly to the increases of urbanization effects on SOS, but the increasing urban heat island intensity in autumn did not lead to the increases of urbanization effects on EOS in Northeast China.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

Preventing or treating infections at implantation sites where the risk of bacterial contamination is high requires the development of intelligent drug delivery systems. In this work, honeycomb structures as a potential drug carrier were obtained for the first time in a fast, one-step anodization process of titanium grade 4, lasting only 60 seconds. Fourth generation oxide nanotube layers were obtained from an aqueous solution of 0.5% AgNO3 in the voltage range from 50 to 80 at 15(1) °C. The FE-SEM method showed the length of the oxide nanotubes from 1.02(2) µm at 50 V to 230(8) nm at 80 V. The EDS analysis revealed that during anodizing, silver particles are deposited on the Ti G4 up to 2.2(5) wt.%. Electrochemical measurements by open circuit potential and anodic polarization curves methods proved the improvement of in vitro corrosion resistance as a result of Ti G4 anodizing. Assessment of the anodized Ti G4 as gentamicin sulfate carrier carried out using ATR-FTIR and UV-VIS absorption spectroscopy revealed that the obtained oxide nanotube layers can be used for application of drugs directly to the tissue around the implant. This method of application allows full use of the therapeutic dose of the antibiotic used.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

The study put forward a data fusion approach for urban remote sensing that combines SAR (Synthetic Aperture Radar) and optical satellite data. By integrating datasets from different sensors and spatial-temporal scales, the technique aims to extract more accurate information. The fusion approach utilizes two methods: feature-based fusion, where relevant features are extracted and fused, and simple layer stacking (SLS), where the original datasets are directly stacked as multiple layers. This study extracted features using SAR textures (using Sentinel-1) and modified indices (using Landsat-8), and then classified these features using an XGBoost algorithm implemented in Python and Google Earth Engine. Researchers examined five cities, each representing a distinct climatic zone and urban dynamic: Cape Town, Guangzhou, Los Angeles, Mumbai, and Osaka. An accuracy assessment was conducted using random validation points, achieving an overall accuracy of 89.5% using the proposed MSFI method. A comparison was also performed with three well-known global products. The proposed approach, outperformed all three global products achived 89% accuracy while ESA (84%), ESRI (81%) and Dynamic World (82%). Additionally, Land surface temperature analysis was accomplished to investigate the relationship between extracted UIS and Land Surface Temperature (LST) across selected cities to show the practical use of proposed MSFI method. Los Angeles, a warm temperate city, showed the highest LST among all five cities. The datasets, along with the GEE and Python codes, are available at https://github.com/mnasarahmad/sls.

The primary objective of this study was to demonstrate the potential of digital image analysis as a tool to identify microplastic (MP) particles in surface waters and to facilitate their characterisation in terms of 2D and 3D morphology. Digital image analysis preceded by microscopic analysis was used for an exhaustive quantitative and qualitative evaluation of MPs isolated from the Vistula river. Using image processing procedures, 2D and 3D shape descriptors were determined. The Principal Components Analysis (PCA) was used to interpret the relationships between the parameters studied, characterising MP particle geometry, type and colour. This multivariate analysis of the data allowed 3 or 4 main factors to be extracted, explaining approximately 90% of the variation in the data characterising MP morphology. It was found that the first principal component for granules, flakes and films was largely represented by strongly correlated with 2D shape descriptors (area, perimeter, equivalent area diameter) and 3D shape descriptors (CSF, Compactness, Dimensionality). Considering the scraps, PC1 was represented by only five of the above descriptors, and the Compactness variable had the largest contribution to PC2. In addition, for granules, flakes and films, a relationship between 2D shape and the colour of their particles could be observed. For the most numerous MP group identified of multicoloured scraps, no such association was found. The results of our study can be used for further multivariate analysis regarding the presence of microplastic floating on the river surface, with a particular focus on particles of secondary origin. This is of key importance for optimising future efforts in conducting small-scale and multidimensional monitoring of and reducing plastics in the aquatic environment.

Low-frequency electromagnetic induction (EMI) is a non-invasive geophysical method that is based on the induction of electromagnetic (EM) waves into the subsurface to quantify changes in electrical conductivity. In this study we present an open (design details and software are accessible) and modular system for the collection of EMI data. The instrument proposed allows to adjust the separations between the transmitter and up to four receiving antennas as well as the acquisition frequency (in the range between 3 and 50 kHz) to permit measurements with variable depth of investigation. The sensor provides access to raw data and the software described in this study allows control of the signal processing chain. The design specifications permit apparent conductivity measurements in the range of between 1 mS/m and 1000 mS/m, with a resolution of 1.0 mS/m and with a sampling rate of up to 10 samples per second. The sensor allows for a synchronous acquisition of a time stamp and a location stamp for each data sample. The sensor has a mass of less than 5 kg, is portable and suitable for 1-person operation, provides 4 hours of operation time on one battery charge, and provides sufficient rigidity for practical field operations.

Since the discovery of the phenomenon of surface-enhanced Raman scattering (SERS), it has gradually become an important tool for the analysis of material compositions and structures. The applications of SERS have been expanded from the fields of environmental and materials science to biomedicine, due to the extremely high sensitivity and non-destructiveness of SERS-based analytical technology that even allows single molecule detection. This article provides a comprehensive overview of Surface-Enhanced Raman Scattering (SERS) phenomenon. The content is divided into several main sections: basic principles and the significance of Raman spectroscopy; historical advancements and technological progress in SERS, as well as various practical applications across different fields. We also discussed how electromagnetic fields contribute to the SERS effect, the role of chemical interactions in enhancing Raman signals, modeling and computational approaches to understand and predict SERS effects.

Deflectometry is a key component in the precise measurement of specular (mirrored) surfaces, however traditional methods often lack an end-to-end approach that performs 3D reconstruction in a single shot with high accuracy and generalizes across different free-form surfaces. This paper introduces a novel deep neural network (DNN)-based approach for end-to-end 3D reconstruction of free-form specular surfaces using single-shot deflectometry. Our proposed network, VUDNet, innovatively combines discriminative and generative components to accurately interpret orthogonal fringe patterns and generate high-fidelity 3D surface reconstructions. By leveraging a hybrid architecture integrating a Variational Autoencoder (VAE) and a modified U-Net, VUDNet excels in both depth estimation and detail refinement, achieving superior performance in challenging environments. Extensive data simulation using Blender, leading to a dataset which we are making available, ensures robust training and enables the network to generalize across diverse scenarios. Experimental results demonstrate the strong performance of VUDNet, setting a new standard for 3D surface reconstruction. The implementation of VUDNet is available on GitHub at https://github.com/hadious/VUDNet.

A new two-step method for developing a nanocomposite of polypropylene (PP) decorated with photocatalytically active TiO2 nanoparticles (nTiO2) is proposed. This method involves low-temperature plasma functionalization of polypropylene followed by ultrasound-assisted anchoring of nTiO2. The nanoparticles, polymeric substrate, and resultant nanocomposite were thoroughly characterized using nanoparticle tracking analysis (NTA), microscopic observations (SEM, TEM, EDX), spectroscopic investigations (XPS, FTIR), thermogravimetric analysis (TG/DTA), and water contact angle (WCA) measurements. The photocatalytic activity of the nanocomposites was evaluated through the degradation of methyl orange. The individual TiO2 nanoparticles ranged from 2-6 nm in size. Oxygen plasma treatment of PP generated surface functional groups (mainly -OH and -C=O), transforming the surface from hydrophobic to hydrophilic, which facilitated efficient deposition of nTiO2. Optimized plasma treatment and sonochemical deposition parameters resulted in an active photocatalytic nTiO2/PP system, degrading 80% of methyl orange under UVA irradiation in 200 minutes. The proposed approach is considered versatile for the functionalization of polymeric materials with photoactive nanoparticles and, in a broader perspective, can be utilized for the fabrication of self-cleaning surfaces.

Melatonin is a ubiquitous molecule found in living organisms, ranging from bacteria to plants and mammals. It possesses various properties, partly due to its robust antioxidant nature and partly owed to its specific interaction with melatonin receptors present in almost all tissues. Melatonin regulates different physiological functions and contributes to the homeostasis of the entire organism. In the human eye, a small amount of melatonin is also present, produced by cells in the anterior segment and the posterior pole, including the retina. In the eye, melatonin may provide antioxidant protection along with regulating physiological functions of ocular tissues, including intraocular pressure (IOP). Therefore, it is conceivable that the exogenous administration of sufficiently high amounts of melatonin to the eye could be beneficial in several instances: for the treatment of eye pathologies like glaucoma, due to the IOP-lowering and neuroprotection effects of melatonin; for the prevention of other dysfunctions, such as dry eye and refractive defects (cataract and myopia) mainly due to its antioxidant properties; for diabetic retinopathy due to its metabolic influence and neuroprotective effects; for macular degeneration due to the antioxidant and neuroprotective properties; and for uveitis, mostly owing to anti-inflammatory and immunomodulatory properties. This paper reviews the scientific evidence supporting the use of melatonin in different ocular districts and provides data suggesting that the topical administration of melatonin as eye drops is a real possibility. This way, its distribution and concentration in different ocular tissues may support its pleiotropic therapeutic effects.

: Since the COVID-19 pandemic, people have become aware that materials (products) can transmit infection and have begun to focus on questions such as how bacteria and germs, the sources of in-fection, maintain their infectivity on material surfaces, and the extent to which materials can or cannot prevent this. and to what extent materials can and cannot prevent it. The SIAA, a non-profit organization of many Japanese companies, had created an entirely separate interna-tional standard for materials' antibacterial, antiviral, and antibiofilm properties (products). The authors have studied the academic basis for the operation of the standards and were deeply in-volved as researchers in establishing one of the standards. This paper describes the interna-tional standards and some representative examples of the authors' actual use of these standards and explains the current status and future problems.

Infections are a common post-operative ailment for patients who have received a dental implant or device and can be attributed to biofilm formation in tissue or on the implant. Many current solutions for oral hygiene have side effects and affect the natural oral microbiome. 2-heptylcyclopropane-1-carboxylic acid (2CP) is a medium-chain fatty acid and synthetic diffusible signaling factor that can prevent and disperse biofilm. The purpose of this work was to evaluate an immersion strategy for coating hydroxyapatite (HAp) with 2CP to prevent biofilm attachment on and around natural teeth and dental implants. The release profile of 2CP-loaded and 2CP+oral rinse-loaded HAp coupons (n=6) was assessed by a 3-day exposure to phosphate buffered saline (PBS). Antimicrobial properties against Porphyromonas gingivalis and cytocompatibility of 2CP-loaded HAp coupons (n=4) were also assessed alone and in combination with 0.12% chlorhexidine gluconate oral rinse. The majority of 2CP is released by 12 hours. 2CP, oral rinse, and 2CP+oral rinse significantly reduced P. gingivalis viability, though direct contact assay demonstrates a significant reduction in Saos-2 viability for oral rinse and 2CP+oral rinse coupons. Immersion or rinsing hydroxyapatite with 2CP could inhibit biofilm-associated dental infections and prevent further complications including caries, gingivitis, and peri-implantitis.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

The study of localized surface plasmons (LSPs) in nanoscale structures is an essential step towards identifying optimal plasmonic modes that can facilitate robust optomechanical coupling and deepen our understanding of light-matter interactions at the nanoscale. This paper investigates numerically, using the finite element method, LSPs modes in a design comprising two coupled nano-ridges deposited on a gold layer, with an interposing polymer spacer layer. Such a structure, usually referred to as particles-on-mirror, shows exquisite optical properties at the nanoscale. We first examine the LSPs modes of a single nano-ridge through the analysis of its scattering cross-section in the visible and infrared range. To enhance the plasmonic response, a thin polymer layer is placed at the middle of the ridge, which introduces additional LSPs modes confined within the former. Then, we extend the analysis to the dimer configuration, which exhibits more complex and enhanced plasmonic behavior compared to a single nano-ridge. In particular, the dimer configuration yields LSPs resonances with a quality factor enhancement of approximately threefold relative to single nano-ridge. Furthermore, the presence of the polymer layer within the ridges significantly improves plasmon field localization and quality factor. These findings underscore the potential of nano-ridge-based structures in advancing optomechanical coupling and plasmon-phonon interaction studies, offering valuable insights for the development of high-performance acousto-plasmonic devices. In particular, the proposed device could help significantly improve the design of nano-acousto-optic modulators operating in the visible or in the near infrared, that require enhanced light-photon coupling rate.

Side-chain liquid crystal polymers have been mixed with ferromagnetic particles, and the for-mation of a monodomain in magnetic fields studied. At relatively low concentrations, the presence of ferroparticles substantially speeds up the rate of formation of a monodomain with the magnetic field and at a given concentration of ferrofluid that rate is independent of the magnetic field strength. In this way, rapid formation of a monodomain is possible at magnetic field strengths far lower than required for the liquid crystal polymer alone. This is anticipated to very helpful in the fabrication of devices based on monodomain liquid crystal elastomers. Wide angle x-ray scattering has been used to monitor the formation of the monodomain and small angle x-ray scattering can give some indication of the ferroparticle behaviour. A model is developed to explain the behaviour. The alignment properties of the ferroparticles is related to their ability to form chains under the influence of very low magnetic fields; these chains are of relatively low stability and may become disrupted after long times, high magnetic fields, or high concentrations. In general, the best results for alignment were at volume fractions below 1%, and under these con-ditions there is the potential for producing monodomain samples with improved properties; in particular shape changes with temperature are significantly larger as a result of improved backbone orientation. Experiments involving monodomain formation and director realignment suggest that the presence of ferroparticles results in a modification in the mechanism for alignment development driven by the organisation of the polymer backbone as a consequence of the con-straints offered by the morphology of the chains of ferroparticles.

Fibromyalgia (FM) is a chronic central sensitivity syndrome characterized by augmented pain processing at diffuse body sites and presents as a multimorbid clinical condition. Long COVID (LC) is a heterogenous clinical syndrome that affects 10-20% of individuals following COVID-19 infection. FM and LC shares similarities with regards to the pain and other clinical symptoms experienced, thereby posing a challenge for accurate diagnosis. This research explores the feasibility of using surface enhanced Raman spectroscopy (SERS) combined with soft independent modelling of class analogies (SIMCA) to develop classification models differentiating LC and FM. Venous blood samples were collected using two supports, dried bloodspot cards (DBS, n= 48 FM and n= 46 LC) and volumetric absorptive micro sampling tips (VAMS, n= 39 FM and n= 39 LC). A semi-permeable membrane (10 kDa) was used to extract low molecular fraction (LMF) from the blood samples, and Raman spectra was acquired using SERS with gold nanoparticles (AuNPs). Soft Independent Modelling of Class Analogy (SIMCA) models developed with spectral data of blood samples collected in VAMS tips showed superior performance with a validation performance of 100% accuracy, sensitivity, and specificity achieving an excellent classification accuracy of 0.86 area under the curve (AUC). Amide groups, aromatic and acidic amino acids were responsible for the discrimination patterns among FM and LC syndromes, emphasizing the findings from our previous studies. Overall, our results demonstrate the ability of AuNPs SERS to identify unique metabolites that can be potentially used as spectral biomarkers to differentiate FM and LC.

We investigated the micro-threaded stem taper surface and the impact on premature failures, aseptic loosening, and infection. We have focused on the fretting, and crevice corrosion of micro-threaded tapers, as well as the characterization of microstructure and surface properties of two new and three retrieved Zweymüller stem tapers of cementless hip endoprostheses selected from a set of 45 stems. The retrievals examined were those in which the sole source of modularity with a metallic component was the head-stem taper interface between the Ti alloy taper stem and the ceramic head. To determine the surface chemistry and microstructures of both new and retrieved hip endoprostheses stem taper titanium alloy, scanning electron microscopy (SEM) was employed for morphological and microstructural analyses. At the same time, energy dispersive spectroscopy (EDS) was utilized for characterizing chemical element distribution, and electron backscattered diffraction (EBSD) was used for phase analysis. The micro-threated stem taper’s roughness for different manufacturers was investigated using an optical profilometer. Standard roughness pa-rameters Ra (average surface roughness) and Rz (mean peak to valley height of the roughness pro-file) were used in this investigation.Additionally, profile depth and peak spacing for different samples were investigated. The surface roughness results indicate no significant difference in roughness associated with varying survivorship times, ranging from 3 to 239 months, and across different manufacturers. Electrochemical studies revealed no fretting corrosion in retrieved stem tapers (ceramic head) that prematurely failed due to aseptic loosening after 239 months, infection after 3 months, and low-grade infection after a 32-month lifetime. Therefore, three retrieved ta-pers and two new ones for comparison underwent potentiodynamic measurements in Hank’s so-lution to ascertain the corrosion rate of new and retrieved stem taper surfaces. The results show a low corrosion rate for both new and retrieved samples that failed prematurely due to aseptic loosening. However, the corrosion rate of infected and low-grade infected tapers was higher. In conclusion, our study aligns with existing literature, suggesting that the use of ceramic heads de-creases the problem of taper corrosion and subsequently reduces premature failures in total hip arthroplasty.

The de-oxygenation process in water used in well injection operations is an important matter to eliminate corrosion in petroleum industry. This study used molecular dynamics simulations to understand the behavior of siloxane surface through studding the surface properties with two functional groups attached to the end of siloxane and their effect on de-oxygenation process. The simulations were performed using LAMMPS to characterize of surface properties. Jmol software was used to generate siloxane chains with (8, 20, and 35) repeat units. Firstly, we evaluated properties such as total energy, surface tension and viscosity. Then, we used siloxane as a membrane to compare the efficiency of de-oxygenation for the both types of functional groups. The results indicated that longer chains length increased total energy, viscosity while decreased surface tension. Replacing methyl groups with trifluoromethyl (CF3) groups increased all the above mentioned properties in varying proportions. Trifluoromethyl (CF3) groups showed better removal efficiency than methyl (CH3) groups but allowed more water to pass. Furthermore, the simulations were run using the class II potential developed by Sun, Rigby, and others within an explicit-atom (EA) model.

A method for estimating river water surface elevation (WSE) from Landsat imagery using the river inundation area - water surface elevation (RIA-WSE) rating curve constructed from the U.S. Geological Survey Topobathymetric Elevation Model (TEM) data was developed and tested at six gauging stations along the upper Mississippi River. The Otsu's automatic threshold selection algorithm was employed for the image classification and estimation of inundation areas within each pre-defined polygon around each gauging station. In addition to the commonly used green-band based water indices, Landsat 8 and 9 OLI's ultra-blue, blue, and red band-based water indices were also tested in this study, which resulted in twenty different water indices: NDWIv (Normalized Difference Water Index), MNDWI1v and MNDWI2v (Modified Normalized Difference Water Index), AWEIsv (Automatic Water Extraction Index with shadow), and AWEInsv (AWEI without shadow), where v represents the visible light band used in the water index. At each station, about 60-80 Landsat 8 or 9 images during 2013-2023 were used for assessing the performances of the twenty water indices through comparing the estimated WSEs with the measured WSEs. Results showed that the ultra-blue or red band-based AWEIs yielded the most accurate estimations of WSEs among the twenty tested water indices.

In the context of restorative dentistry and the use of different techniques and dental adhesive systems, this study was to designed to assess the degree of adhesive absorption and wetting for each dental micro applicator; and also quantify the amount of lost fiber flocks after three applications of dental adhesive on the inside surface of a plastic veneer tooth in order to reveal a potential contaminating factor at the adhesive interface. Initially, one drop of dental adhesive was dispensed into a glass dental mixing well. The dental adhesive was then applied onto the inside surface of the veneer restoration for 30s using a dental micro applicator which was weighed afterwards. For each dental micro applicator, this sequence was repeated three times and measured again by the same operator. Each adhesive application was analyzed separately, to show the values independently and compare them to the initial weight. The samples of Fiber-Free Elastomer Bristle Micro Applicators (FEBM) demonstrated the best performance with a good degree of absorption and wetting of the dental adhesive without the loss fiber flocks and release-induced weight loss. The samples of Conventional Fiber Flocked Micro Applicators (CFFM) demonstrated good initial absorption and wetting of the dental adhesive, but visually shed several fiber flocks which resulted in significant weight loss and can also be considered a contaminating factor at the adhesive interface.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

Thermal plasma is a versatile technology that can be used to treat various types of wastes, including vegetal and mineral oils, solvents, plastics, papers and cardboard, glasses, bricks and rocks, metals, clothes, and mixtures of these materials. In this study, we utilized a commercial plasma cutter as a thermal plasma source to decrease the volume of a simulated low-level radioactive mixed solid waste. The simulated waste included papers, plastics, clothes, gloves, metals and stable Co, Cs, Sr, and Ce additives as surrogates of 60Co, 137Cs, 90Sr, and 144Ce, the latter typical contaminants in nuclear LLW. As a result of the process two products were obtained, a solid phase in which we focused this work and a gaseous phase. To retain as much as possible surrogates in the solid final phase, crushed glass from broken bottles was included as a vitrification additive to the original waste. After undergoing heat treatment, a dense vitreous slag was produced and ashes. The process resulted in a volume reduction of 70%, indicating the successful gasification of organic excess materials. The surrogate elements were retained in the process and were found in the ashes composition: Co (3.4% w/w), Cs (37.7% w/w), Ce (0.6% w/w) and in the glass matrix composition of Co, Cs, Sr and Ce: 72.4 ± 14.7, 32 ± 18.2, 125.3 ± 31.6, 80 ± 13.1 % w/w respectively. For the actual experimental conditions, retention efficiencies were estimated for Cobalt (Co) at 72.4 ± 14.7%, Cerium (Ce) at 80 ± 13.1%, Strontium (Sr) at 125.3 ± 31.6%, and notably Cesium (Cs) at 32 ± 18.2%.