Typically, a diesel generator on the merchant ship, composed of a wound rotor synchronous generator and a four-stroke diesel engine, supplies electrical power to various loads. Recently, shaft generators for merchant vessels are increasingly replacing diesel generators to reduce CO2 emissions through fuel efficiency improvement. In particular, permanent magnet generators replace induction generators due to their high-efficiency characteristics at light loads. The surface-mounted permanent magnet can be a suitable rotor topology due to the relatively short constant power range. This generator can also operate as a motor according to the propulsion mode, so minimizing the harmonics of the induced voltage and the torque ripple is necessary. This paper proposes an alternative NdFeB magnet pole topology combined with the modular step-skewed rotor. The step-skewed rotor affects to reduce higher-order harmonics, and the modular pole reduces the permanent magnet assembly process and harmonics in voltage and torque. A 2-D finite element method is used to evaluate the harmonics of induced voltage and torque pulsation for the proposed topology. The topology shows harmonic minimization effect by comparing the characteristics of three flatted-bottom magnets. Compared to the tapered bread-loaf magnet, voltage harmonics to the 100th component are almost the same, and the torque ripple is reduced by more than 12% at the same residual flux density. The analysis method is verified by comparing test and analysis results for prototype machines with similar specifications.

The extreme environmental issues and the resulting needs to save energy have turned the attention to electrification of energy applications. One of the key components involved in energy efficiency improvements is the appropriate conception and manufacturing of electric machines. This paper overviews the electromagnetic analysis governing the behavior of permanent magnets that enabled substantial efficiency gains in recent electric machine developments. Particular emphasis is given to model the properties and losses developed in permanent magnets in the emerging high speed applications. In addition, the investigation of properties and harmonic losses related to ferromagnetic materials constituting the machine magnetic circuits are equally analyzed and discussed. The experimental validation of the implemented methodologies and developed models with respect to the obtained precision is reported. The introduction of mixed numerical techniques based on the finite element method intended to appropriately represent the different physical phenomena encountered is outlined and discussed. Finally, fast and accurate simulation techniques including aggregated lumped parameter models considering harmonic losses associated with inverter supplies are commented.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

This study aimed to improve sensitivity of ferrous particle sensors used in various mechanical systems such as wind power gearboxes to detect abnormalities by measuring the amount of ferrous wear particles generated by metal-to-metal contact. Existing sensors collect ferrous particles using a permanent magnet. However, its ability to detect abnormalities is limited because it only measures amounts of ferrous particles collected on the top of the sensor. To overcome this limitation, this study evaluated sensibility of an existing sensor using a multi-physics analysis method and improved it by changing the core shape inside the sensor. The detection ability of the improved sensor was analytically shown to be better than the existing sensor. This study highlights the use of analytical methods and multi-physics analysis for developing a ferrous particle sensor and presents a method to compare sensibility analytically. Results of the improved sensor are expected to enhance the ability to detect abnormalities in the lubrication system where ferrous wear particles are generated. This study will contribute to the development of more effective ferrous particle sensors, which can potentially improve the performance and reliability of mechanical systems.

Permanent magnet synchronous motor (PMSM) AC servo system shows the characteristics of uncertainty, time-varying and non-linearity, which makes it difficult for traditional PID control to achieve ideal control effect. Fuzzy control has strong adaptability to the problems of parameter variation, non-linearity and model inaccuracy of the controlled object. Vector control strategy is used to study its control principle and the realization of SVPWM. Because the motor object has certain fractional order characteristics, the fuzzy parameter self-tuning PIλ control is chosen as the position regulator of servo motor. It combines the accuracy of fractional order PI control and the adaptability of fuzzy control. A simulation model of PMSM three-closed-loop system is built in MATLAB/Simulink environment. The results show that the control method is effective and can satisfy the trajectory tracking of servo control.

Interior permanent magnet motors (IPMSMs) are extensively used as traction motors today because of their exceptional torque and power density, and wide constant power operating range. Under real-world usage, an IPMSM rotor undergoes varying electromagnetic, thermal, and mechanical loads. Under such conditions, fatigue life-based design criteria should be utilized over stress-based design criteria to ensure the structural integrity of the rotor. Moreover, the driving dynamics can change the rotor temperature continuously, which affects the electromagnetic, mechanical, and fatigue properties of rotor material. This paper proposes a robust thermo-mechanical rotor fatigue simulation workflow considering the significant loads acting on an IPMSM rotor and the temperature variation throughout a drive cycle. It discusses an accelerated fatigue life estimation approach based on peak valley extraction to reduce the simulation time significantly for stress and fatigue analysis. Then, it presents a method for stress-life curve generation for a variable loading. It also presents a sensitivity study with a median S-N curve, and a 90%-reliability 95%-confidence (R90C95) S-N curve.

In this paper, the design and performance investigation of the permanent magnet machines have been done to increase the mechanical and electrical outputs improvement of the systems. A permanent magnet Dc motor (PMDM) and generator (PMDG) have been modelled and designed to improve the angular position and generated current respectively. In this work, augmentation based H 2 optimal and H infinity synthesis controllers have been designed as a controller for the two systems and a comparison between the proposed controller for tracking a reference inputs and a promising results have been obtained.

In this paper, modification of dual-Halbach permanent magnet (PM) array is investigated to improve performance of tubular linear machine, in terms of flux density and output power. Instead of a classical Halbach array with only radial and axial PMs, proposed model involves insertion of mig-magnets, which have magnetized angle shifted from the reference magnetized angles of axial and radial PMs. This structure leads to elimination of flux leakage and concentration of flux linkage in middle of the coil; therefore, the performance of machine is increased.

This paper proposes an analytical model of the double-stator spoke-type permanent-magnet vernier machine (DSSTVM) using the subdomain model (SDM), which can be used to calculate the mag-netic field distribution and corresponding electromagnetic parameters of the DSSTVM. The whole field domain is divided into several subdomains according to the magnetic characteristics of each region, within which Laplace's and Poisson's equations are solved accordingly in terms of magnetic vector potential (MVP). Then, the magnetic flux density distribution, back electromotive force (EMF), and electromagnetic torque of the DSSTVM can be obtained correspondingly. Ultimately, finite element analysis (FEA) is adopted to validate the proposed analytical model's effectiveness for quickly predicting the no-load and on-load performances of the DSSTVM.

In this paper, a robust nonlinear dynamic controller is designed for a wind turbine with a permanent magnet synchronous generator. The wind turbine is subject to variations in all the parameters appearing in its mathematical model. Furthermore, the wind velocity is considered unavailable for direct measurement. This situation is of particular interest in practical applications, where only the nominal parameter values are known, and accurate wind velocity measurement is challenging due to perturbations caused by the turbine itself, even with appropriate sensors. The problem addressed in this work involves tracking the reference angular velocity corresponding to the wind velocity. To achieve accurate tracking, appropriate compensation of the perturbation terms resulting from parameter uncertainties and wind estimation errors is required. To address this problem, an estimator of the wind velocity is utilized, along with high–order sliding mode parameter estimators, to ensure high–performance operation of the turbine.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

Ensuring precise electric locomotive stopping is pivotal for achieving intelligent and unmanned auxiliary transportation systems. Currently, human drivers' expertise plays a central role in the stopping process, posing challenges for automation and cargo location accuracy, particularly in coal mining. This paper focuses on achieving accurate electric locomotive stopping under diverse conditions by utilizing permanent magnet synchronous motor-driven locomotives. This technique introduces a novel stopping control method that combines a fuzzy Proportional-Integral-Derivative (F-PID) controller and a vector control model for permanent magnet synchronous motors (PMSM). After this, we design the F-PID using the PMSM technique based on the new fuzzy rules for each sub-system. In the end, extensive simulations and real-world experiments are conducted on an electric locomotive stopping test bed, which demonstrate the effectiveness of the proposed control method. From the simulation results, it confirming that the ability to achieve precise stopping under various working conditions.

This paper proposes the optimization method for the minimum mass of permanent magnet (PM) excited homopolar inductor alternator (HIA) with air-gap winding used for high-speed driving system. The calculation results show that there is an optimal value for shell diameter and unit number of HIA to make the mass to be smallest. A 1 MW at 22000 rpm PM excited HIA is designed. The analytical results are verified by the FEM simulations. The losses, temperature rise, rotor stress and modal of the PM excited HIA are also analyzed. The calculation results show that the solid rotor eddy-current losses and the temperature rise of PM excited HIA are acceptable. Also the rotor strength is adequate, and the rotor system is a stiffness rotor, and it can safely operate. Finally, the comparison between PM excited HIA and permanent magnet rotor machine is discussed.

Due to its high power, high efficiency, low pollution, and compact size, permanent magnet synchronous motors (PMSMs) have been widely used in a variety of fields, including electric vehicles, aerospace, wind turbines, and marine devices which are used in renewable, sustainable, and environmentally friendly energy resources. However, in these practical scenarios, the motor operating conditions are complex and variable. Under high temperatures and high current conditions, PMSMs may experience demagnetization failures, not only leading to performance degradation but also inducing unexpected failures of the motors. To reduce the risk of unexpected losses caused by demagnetization faults and improve the safety and reliability of motor systems, it is necessary to apply automated monitoring of the magnet flux of the motor's permanent magnets and achieve real-time diagnosis of early demagnetization faults, ensuring the safe operation of the motor. This review article tries to summarize the current detecting methods of the automated monitoring of demagnetization faults in PMSMs. The main online monitoring technologies from both practical and academic perspectives were summarized and their benefits and challenges have been reviewed. Finally, the research trends and suggestions for future improvements are provided. This review article will not only shed light on the origins of the automated monitoring of demagnetization faults but also help to design highly effective and sustainable permanent magnet synchronous motors.

This paper proposes a new structure of the dual-rotor hybrid-excited axial-flux permanent magnet vernier machine (DR-HEAFPMVM) with the modular stator and the consequent-pole PM (CPM) rotor for low-speed, high torque density applications such as in-wheel electric vehicles. The tooth-wound non-overlapping armature windings and direct current (DC) excitation windings are respectively arranged in stator main-teeth and split-teeth to obtain the modulated and adjustable air-gap flux densities, which result in the high torque density and outstanding flux-weakening capability. First, the design consideration, operation principle, and the air-gap flux density distributions of the proposed machine are elaborated based on the air-gap permeance function. Then, the influence of the pole ratios (PRs) and the DC excitation currents on the main electromagnetic performances of the DR-HEAFPMVM, such as the flux-weakening capability, back-electromotive force (back-EMF), on-load electromagnetic torque, loss distribution, and efficiencies, is investigated using the 3-D finite-element method (FEM). Results verify the feasibility of the flux adjustment of the DC excitation windings equipped in the split-tooth, and the design with a pole ratio of 8/1 tends to have higher torque density, higher machine efficiency, and considerable flux-weakening capability compared with the other two PRs.

Interior permanent magnets motors are widely used in applications requiring high power den-sity and high efficiency due to their high torque generating capabilities. Recently, given the re-cent price fluctuations and unstable supply of rare-earth permanent magnets, alternative config-urations with reduced use of permanent magnets are being sought. Among the various candi-dates related to this, the consequent-pole type rotor structure can halve the number of perma-nent magnets used compared with conventional structures. However, in the no-load analysis, the waveform of the back electromotive force becomes asymmetric, generating a harmonic component. As a result, there is a disadvantage that the torque ripple increases. To overcome these shortcomings, we propose a novel rotor structure that applies a consequent-pole structure to an embedded permanent-magnet motor structure, wherein a number of permanent magnets are arranged in a flared structure to constitute a single polarity. In the proposed flared-structured magnet arrangement, it is possible to adjust the angle of the permanent magnet and the polar angle to mitigate the asymmetry of the back EMF waveform. The proposed struc-ture was optimized with a genetic algorithm and a prototype of the optimal model was con-structed and experimentally evaluated to verify its validity. Finally, the performance improve-ment and validity of the proposed structure were verified by comparing the analysis results of the optimal model with the experimental results.

Full-order state-space models represent the starting point for the development of advanced control methods for wind turbine systems (WTSs). Regarding existing control-oriented WTS models, two research gaps must be noted: (i) There exists no full-order WTS model in form of one overall ordinary differential equation that considers all dynamical effects which significantly influence the electrical power output; (ii) all existing reduced-order WTS models are subject to rather arbitrary simplifications and are not validated against a full-order model. Therefore, in this paper, two full-order nonlinear state-space models (of 11th and 9th-order in the (a, b, c)- and (d, q)-reference frame, resp.) for variable-speed variable-pitch permanent magnet synchronous generator WTSs are derived. The full-order models cover all relevant dynamical effects with significant impact on the system’s power output, including the switching behavior of the power electronic devices. Based on the full-order models, by a step-by-step model reduction procedure, two reduced-order WTS models are deduced: A non-switching (averaging) 7th-order WTS model and a non-switching 3rd-order WTS model. Comparative simulation results reveal that all models capture the dominant system dynamics properly. The full-order models allow for a detailed analysis covering the high frequency oscillations in the instantaneous power output due to the switching in the power converters. The reduced-order models provide a time-averaged instantaneous power output (which still correctly reflects the energy produced by the WTS) and come with a drastically reduced complexity making those models appropriate for large-scale power grid controller design.

a sensorless control scheme based on novel power converging law sliding mode observer is suggested to realize the sensorless control for the permanent magnet synchronous motor (PMSM). Firstly, by introducing a new power converging law, the problem of slow converging speed/large chattering value dilemma in the conventional converging law is solved; Secondly, in view of the shortcomings of the conventional position and speed estimation algorithm, the high-frequency buffeting in the sliding mode observer will be expanded, a phase-locked loop (PLL) velocity and position estimation strategy is adopted to replace it. Finally, through Matlab/Simulink modeling and motor speed regulation platform experimental results, the sensorless position and speed estimation technology proposed in this paper can respond to the starting speed command of 1000 r/min within 0.05 s, and the starting process has no overshoot. When disturbed by 10Nm loading, the speed fluctuation value can be controlled within 1%.

During flux weakening operation time (FWOT), the total iron loss rises and affects the accuracy of loss prediction and efficiency especially if a large range of FWOT exists. Iron loss prediction is widely employed in investigations for a fast electrical machine analysis using 2-D FEA. This paper studies harmonic loss analytically by a steady-state equivalent circuit. Consideration of skin effects and iron saturation are utilized in order to examine the accuracy through the relative error distribution in the frequency domain of each model from 50 to 700 Hz. Additionally, this comparative study presents a torque-frequency-flux density calculation over each single term of the modified IEM-formula. The analytical calculation is performed using 2-D FEA for a classic and modified IEM-formula along with experimental verifications on a surface-mounted PMSG for a wind generation application.

The Wind Energy Conversion System (WECS) plays an inevitable role across the world. In particular, the attention for Permanent Magnet Synchronous Generators (PMSGs) connected with wind farm is popular. This paper deals with the literature review that describes the recent advances, progresses and innovatory trends on PMSGs for WECS. Comparison between geared and direct-driven conversion systems and the classification of electrical machines used in WECS are discussed. A detailed analysis on the design aspects considering various topologies of PMSGs are encompassed in the literature. The PMSG design and optimization problems are solved by field computation techniques and optimized by using Soft Computing (SC) techniques .The three-dimensional, finite element software platform for the analysis and design of PMSGs is discussed. This paper also deals with the interdisciplinary modeling, analysis, and optimization of PMSG using Finite Element Analysis (FEM) and SC techniques. Finally, PMSGs are reviewed and compared for further exploration.

Atomic state preparation can benefit from a compact and uniform magnetic field source. Simulations and experimental measurements have been used to design, build, and test such a source as shown by optical pumping of atomic Helium. This source is a 9.5 mm (3/8") OD x 6.7 mm (1/4") ID x 9.5 mm (3/8") long, NdFeB-N42 assembly of 1.6 mm (1/16") thick customized annular magnets. It has octopole decay with a residual dipole far field from imperfect dipole cancelations. It has greater than 50% clear aperture with uniform and collimated magnetic field consistent with the prediction of several models. Octopole roll-off localizes the field minimizing the need for shielding in applications. The device is applied to a high precision 3,4He laser spectroscopy experiment using σ+ or σ- optical pumping currently resulting in a measured 99.3% preparation efficiency and in accordance with a rate-equation model.

This study presents structural analysis and optimization for the lightweight design of a buoyant rotor-type permanent magnet (BRPM) generator, which was first presented in Bang (2010), and compares its structural performances to a conventional generator with a spoke arm-type rotor and stator. The main benefit of a BRPM is that it can be realized as a bearing-less drive system, free from the mechanical failure of rotor bearings, by using a buoyant rotor. Also, the deformation of a generator by blade vibration can be effectively suppressed using joint couplings between the blades and the rotor. For the design optimization, the objective is set as the mass of the rotor and the stator, and the maximum deformation of the airgap clearance between the rotor and the stator by external forces is constrained below 10% of the gap width. The commercial software Optistruct is used for the analysis and optimization. In this investigation, the analysis and optimization are conducted for a 10 MW wind turbine generator. However, the proposed methods can be extended to larger generator designs without requiring considerable modification. The mass of the opti-mized 10MW BRPM generator is 160.7 tons (19.3 tons for the rotor and 141.4 tons for the stator) while that of an optimized conventional spoke arm-type generator is obtained as 325.6 tons.

Air conditioning system of electric vehicles has new change as the internal combustion engine is being replaced with electrified AC motor. With large amount of batteries installed at the bottom of frame, the conventional compressor which is belt-driven can be removed and another AC motor can play the role for air conditioning in electric vehicles. From this change, the system efficiency would be improved since it is possible to control the electrified compressor independently from traction system in contrast with the belt-driven compressor. As a result, by applying the electrified compressor for air conditioning system, the whole system can achieve better efficiency and longer driving distance, which is most important in electric vehicles. In this paper, 3-phase interior permanent magnet synchronous motor (IPMSM) was designed using lumped-parameter model and finite element method.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Flux-switching permanent magnet (FSPM) motors have gained increasing attention in the electric vehicles (EVs) applications due to the advantages of high power density, high efficiency. However, the heat sources of both permanent magnet (PM) and armature winding are located on the limited stator space in the FSPM motors, which may result in the PM overheated and irreversible demagnetization caused by temperature rise and it is often ignored in the conventional thermal analysis. In this paper, a new electrical-thermal two-way coupling design method is proposed to analyze the electromagnetic performances, where the change of PM material characteristics under different temperatures is taken into consideration. Firstly, the motor topology and design equations are introduced. Secondly, the demagnetization curves of PM materials under different temperatures are modeled due to PM materials are sensitive to the temperature. And based on the electrical-thermal two-way coupling method, the motor performances are evaluated in details, such as the load PM flux linkage and output torque. Then, the motor is optimized, and the electromagnetic performances between initial and improved motors are compared. Finally, a prototype motor is manufactured, and the results are validated by experimental measurements.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

MnSi has played a major role since the late 1970s in developing the theory of helical magnets in non-centro symmetric materials showing Dzyaloshinsky-Moriya interaction (DMI). With a long helimagnetic pitch of 175 \AA~as compared to the lattice d-spacing of 4.55\AA, it was ideal for performing neutron studies especially as large single crystals could be grown. In these studies under the application of a field of 180 mT perpendicular to Q, a so-called A-phase in the B-T phase diagram was found and interpreted as a rotation of the alignment of the magnetic helix away from the pinning axis. After the surprising discovery of the skyrmion lattice in the A-phase in 2009 much interest arose as it could be shown that the magnetic skyrmion lattice is topologically protected. Due to the rigidity of the skyrmionic lattice it is only loosely bound to the crystal lattice and therefore only relatively small current densities can already induce a motion of this lattice. Another very interesting aspect are the excitations in the spin system of MnSi. As the helimagnetic state is characterized by a long pitch of about 175 \AA, the associated characteristic excitations form a band structure due to Umklapp scattering and can only be observed at very small q with energies below 1 meV. We have investigated the the magnons in MnSi in the whole (B,T)-phase diagram starting in the single-k helimagnetic state by applying a small magnetic field B = 100 mT. This way, the complexity of the magnon spectrum is significantly reduced allowing a detailed comparison of the data with theory resulting in a full theoretical understanding of the spin system of MnSi in all its different magnetic phases.

Stimulation of the alpha 7 nicotinic acetylcholine receptor (α7nAChR) has shown beneficial effects in several acute inflammatory disease models. This study aims to examine whether treatment with the selective α7nAChR agonist PHA 568487 can dampen inflammation and thereby improve cardiac function after myocardial infarction in mice. The possible anti-inflammatory properties of α7nAChR agonist PHA 568487 were tested in vivo using the air pouch model and in a permanent occlusion model of acute myocardial infarction in mice. Hematology parameters and cytokine levels were determined. Infarct size and cardiac function were assessed via echocardiography 24 h and one week after the infarction. Treatment with α7nAChR agonist PHA 568487 decreased 12 (CCL27, CXCL5, IL6, CXCL10, CXCL11, CXCL1, CCL2, MIP1a, MIP2, CXCL16, CXCL12 and CCL25) out of 33 cytokines in the air pouch model of acute inflammation. However, α7nAChR agonist PHA 568487 did not alter infarct size, ejection fraction, cardiac output or stroke volume at 24 h nor at 7 days after the myocardial infarction compared with control mice. In conclusion, despite promising immunomodulatory effects in the acute inflammatory air pouch model, α7nAChR agonist PHA 568487 did not affect infarct size or cardiac function after a permanent occlusion model of acute myocardial infarction in mice. Consequently, this study does not strengthen the hypothesis that stimulation of the α7nAChR is a future treatment strategy for acute myocardial infarction when reperfusion is lacking. However, whether other agonists of the α7nAChR can have different effects remains to be investigated.

In the evolving landscape of cybersecurity threats, the Permanent Denial of Service (PDoS) attacks have emerged as a particularly damaging form of cyber aggression. Unlike the more well-known Denial of Service (DoS) attacks, which disrupt services temporarily, PDoS attacks aim to inflict irreversible damage to systems, often resulting in significant system overhauls and requiring hardware replacement. To enable the development of effective security measures, but also to address the knowledge gaps, this paper offers an in-depth exploration of PDoS attacks, emphasizing their distinguishing characteristics, underlying mechanisms, and potential further development. Through a comprehensive case study, the research highlights diverse tactics and strategies employed by attackers, from targeting IoT devices to manipulating boot processes and exploiting firmware vulnerabilities. A novel classification of PDoS attack vectors is proposed, that also explains the ways in which the systems can be compromised. The findings confirm the pressing need for adaptive and robust defense mechanisms to mitigate the threats posed by PDoS attacks in our interconnected digital world.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Sulfate, the main dissolved contaminant in acid mine drainage (AMD), is ubiquitous in watersheds affected by coal and metal mining operations worldwide. Engineered passive bioremediation systems (PBS) are low-cost technologies that remediate sulfate contamination by promoting (1) precipitation of sulfate-bearing compounds, such as schwertmannite and gypsum; and (2) microbially-mediated sulfate reduction (BSR) to sulfide with subsequent precipitation of sulfide minerals. In this study, chemical and sulfur isotopic data are used to infer multiple pathways for sulfate sequestration in the Tab-Simco PBS. By simultaneously monitoring sulfate concentrations and δ34SSO4 values at four sampling points across the PBS, we (1) identified that the organic layer within the bioreactor was the primary site of BSR processes contributing to sulfate sequestration; (2) observed seasonal variations of BSR processes; (3) estimated that initially the BSR processes contributed up to 30% to sulfate sequestration in the Tab-Simco bioreactor; and (4) determined that BSR contribution to sulfate sequestration continuously declined over the PBS operational lifetime. Together, our results highlight the utility of combining geochemical and microbial fingerprinting techniques to decipher complementary processes involved in sulfur cycling in a PBS as well as the value of adding the sulfur isotope approach as an essential tool to help understand, predict, prevent and mitigate sulfate contamination in AMD-impacted systems.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

Introduction: The aim of the present systematic review was to evaluate the clinical and radiographic success of partial pulpotomies in deep caries processes or post-eruptive defects in young, vital permanent teeth. Methods: Electronic databases, PubMed, Scopus, and Embase, were searched, followed by a manual search. Randomized controlled trials evaluating partial pulpo-tomy with a follow-up period of ≥12 months were included. Meta-analyses using a random effect model were performed. Results: A total of 3.127 articles were retrieved, and after duplicate re-moval, 2.642 were screened by title and abstract; 1 additional article was found during the manual search in the reference lists, and 79 were identified. Finally, 6 papers were included in the review. Regardless of the partial pulpotomy modalities or material used, there were no signifi-cant differences between clinical and radiographic success rates (cumulative success rate 91,8%-92,3%, respectively). Five studies were included in the meta-analysis that did not indicate any statistically significant differences in success rates when Mineral Trioxide Aggregate was compared to other materials (95% CI 0,239 to 1,016 p=0.055). Conclusion: This research system-atically evaluates the evidence and summarises the available data on partial pulpotomy in young permanent teeth. Given its high clinical and radiographic success rate, partial pulpotomy should be considered when vital pulpal therapy needs to be performed in highly damaged young per-manent teeth, as this procedure provides a biological benefit and allows more invasive endodon-tic treatments to be postponed.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

The paper deals with the Model Predictive Control (MPC) algorithm as applied to the sensorless control of a Permanent Magnet Synchronous Motor (PMSM). The proposed estimation strategy, based on the unscented Kalman filter (UKF), uses only the measurement of the motor current for the online estimation of speed, rotor position and load torque. Information about the system state feeds the MPC. Results verify the effectiveness and applicability of the proposed sensorless control technique. An implementation in low speed direct drive astronomy telescope mount systems is investigated.

The separation of rare earth metals (REM) from a neodymium magnet has been widely studied in the last year. We have shown that the waste of computer hard disk contains 25.41 % neodymium, 64.09 % iron, and <<1 % boron. To further isolate rare-earth metals, the magnet was acidically dissolved in open and closed systems. In both methods of dissolution was used concentrated nitric acid. The difference between these methods are the conditions of dissolution of magnet. The magnet was dissolved in a microwave sample preparation system at different temperatures and pressures in a closed system. In the open system, the acid dissolution of the magnet conducted at room temperature. 0.2 g of the neodymium magnet sample was taken under two conditions, and the dissolution process in the closed system lasted 1 hour, and in the open system-30-40 minutes. The open system is a non-laborious, simple and cheap method of dissolving the magnet by comparing both systems. Therefore, an open sample preparation system is used for further work. To remove the iron in the magnet, oxalic acid was used and precipitated as oxalates under both conditions. According to the result of the ICP-MS method, it is shown that the neodymium and iron contents in the precipitate are 24.66 % and 0.06 %, respectively. This shows that the iron has almost completely passed to the filtrate. Thus, it is possible to remove the iron from the sample.

Multi-objective optimization (MOO) is an optimization involving minimization of several objective functions more than the conventional one objective optimization which have useful applications in Engineering. Many of the current methodologies addresses challenges and solutions to multi-objective optimization problem, which attempts to solve simultaneously several objectives with multiple constraints, subjoined to each objective. Most challenges in MOO are generally subjected to linear inequality constraints that prevent all objectives from being optimized simultaneously. This paper takes short survey and deep analysis of Random and Uniform Entry-Exit time of objectives. It then breaks down process into sub-process and then presents some new concepts by introducing methods in solving problem in MOO, which comes due to periodical objectives that do not stay for the entire duration of process lifetime unlike permanent objectives, which are optimized once for the entire process lifetime. A methodology based on partial optimization that optimizes each objective iteratively and weight convergence method that optimizes sub-group of objectives is given. Furthermore, another method is introduced which involve objective classification, ranking, estimation and prediction where objectives are classified base on their properties, and ranked using a given criteria and in addition estimated for an optimal weight point (pareto optimal point) if it certifies a coveted optimal weight point. Then finally predicted to find how much it deviates from the estimated optimal weight point. Although this paper presents concepts work only, it’s practical application are beyond the scope of this paper, however base on analysis presented, the concept is worthy of igniting further research and application.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

This manuscript employs a surface stress-driven nonlocal model to explore the combined effects of long-range interaction and surface energy on higher vibration modes of functionally graded nanobeams. The nanobeam theory, based on Bernoulli-Euler kinematics, incorporates surface effects such as surface elasticity, surface residual stresses, surface density, and rotary inertia. Hamilton's principle is applied to derive the governing equation with size-dependent considerations. The main outcomes of a parametric investigation, considering four different kinematic boundary conditions (Cantilever, Simply-Supported, Clamped-Pinned, and Doubly-Clamped) while varying the nonlocal parameter and material gradient index, are presented and discussed. Additionally, the normalized natural frequencies for the second, third, fourth and fifth modes of vibrations are provided and analyzed for each case under study. The results underscore the model's effectiveness in capturing surface energy effects on the overall dynamic behavior of functionally graded Bernoulli-Euler nanobeams, offering a cost-effective approach for designing and optimizing nano-scaled structures.

(1) Background: Prefabricated zirconia crowns are used to restore teeth in children. The purpose of this study was to evaluate the removal of these crowns with the erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser; (2) Methods: Twelve primary and 13 permanent teeth were prepared and prefabricated zirconia crowns were passively fitted and cemented with two resin modified glass-ionomer cements. Surface areas of prepared teeth and crowns were calculated. Crowns were removed using two laser settings: 4.5 Watts, 15 Hertz, 20 water/ 20 air, and 5 Watts, 15 Hertz, 50 water/50 air. The retrieval time and temperature changes were tested recorded. Data were analyzed using ANOVA with Tuckey’s adjusted post hoc pairwise comparison t-test; (3) Results: The average time for crown removal was: 3 minutes, 47.7 seconds for permanent; and 2 minutes 5 seconds for primary teeth. The mean temperature changes were 2.48℃ (SD=1.43) for permanent; and 3.14℃ (SD=1.88) for primary teeth. The time to debond was significantly positively correlated with tooth inner surface area and volume, outer crown volume, and the cement volume; (4) Conclusions: Use of the Er,Cr:YSGG laser is an effective, safe and non-invasive method to remove prefabricated zirconia crowns cemented with RMGI cements from permanent and primary teeth.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Melatonin is a ubiquitous molecule found in living organisms, ranging from bacteria to plants and mammals. It possesses various properties, partly due to its robust antioxidant nature and partly owed to its specific interaction with melatonin receptors present in almost all tissues. Melatonin regulates different physiological functions and contributes to the homeostasis of the entire organism. In the human eye, a small amount of melatonin is also present, produced by cells in the anterior segment and the posterior pole, including the retina. In the eye, melatonin may provide antioxidant protection along with regulating physiological functions of ocular tissues, including intraocular pressure (IOP). Therefore, it is conceivable that the exogenous administration of sufficiently high amounts of melatonin to the eye could be beneficial in several instances: for the treatment of eye pathologies like glaucoma, due to the IOP-lowering and neuroprotection effects of melatonin; for the prevention of other dysfunctions, such as dry eye and refractive defects (cataract and myopia) mainly due to its antioxidant properties; for diabetic retinopathy due to its metabolic influence and neuroprotective effects; for macular degeneration due to the antioxidant and neuroprotective properties; and for uveitis, mostly owing to anti-inflammatory and immunomodulatory properties. This paper reviews the scientific evidence supporting the use of melatonin in different ocular districts and provides data suggesting that the topical administration of melatonin as eye drops is a real possibility. This way, its distribution and concentration in different ocular tissues may support its pleiotropic therapeutic effects.

(1) Background: A simple approach to map irrigated landcover has been introduced by using measures derived from optical spectral range as an alternative to thermal range. It has been demonstrated that substituting surface temperature (Ts, ‘thermal approach’) with SWIR transformed reflectance (STR, ‘optical approach’) to detect surface moisture is feasible with comparable results. (2) Methods: Using an iterative thresholding procedure to minimize within-class variance, the bilevel segmentation of variables derived from Landsat-8 representing surface moisture and vegetation cover was achieved for the 2020-21 summer for a key irrigation district in Australia. (3) Results: The results of irrigated landcover by optical approach found to be comparable with those by thermal approach. The classification accuracy was assessed using water delivery records at farm level. Though the overall accuracy is high in both cases, the optical approach (97.6%) performed slightly better than the thermal approach (93.9%). (4) Conclusions: The feasibility of using STR to map irrigated landcover has been confirmed by a high-level overall accuracy assessment. This has broader implications in terms of irrigated landcover assessment, as the use of satellite imagery in these applications may not necessarily be limited to microwave or thermal sensors.

Two mononuclear Ru(III) complexes of formula trans-[RuCl4(Hgua)(dmso)]·2H2O (1) and trans-[RuCl4(Hgua)(gua)]·3H2O (2) [Hgua = protonated guanine (gua), dmso = dimethyl sulfoxide] have been synthesized and characterized magnetostructurally. Compounds 1 and 2 crystallize in the monoclinic system with space groups P21/n and Pc, respectively. Each Ru(III) ion in 1 and 2 is six-coordinate and bonded to four chloride ions and one (1) or two (2) nitrogen atoms from guanine molecules and one sulfur atom (1) of a dmso solvent molecule, generating quasi regular octahedral geometries in both cases. In their crystal packing, the Ru(III) complexes are self-assembled mainly through an extended network of N-H⋯Cl hydrogen bonds and π⋯Cl type intermolecular interactions, forming novel supramolecular structures based on this paramagnetic 4d metal ion. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a different magnetic behavior. While 1 is a ferromagnetic compound at low temperature, 2 exhibits a behavior typical of noninteracting mononuclear Ru(III) complexes with S = 1/2. Ac magnetic susceptibility measurements reveal slow relaxation of the magnetization in the presence of external dc fields only for 2, hence indicating the occurrence of field-induced single-ion magnet (SIM) phenomenon in this mononuclear guanine-based Ru(III) complex.

A 9.4 T/400 MHz superconducting magnet with a warm bore of 60 mm is being designed. The 400 MHz NMR magnet is composed of 9 coaxial coils to generate a central field of 9.4 T. The magnetic field homogeneity is better than 4 ppm for 50 mm diameter spherical volume (DSV) and better than 1 ppb for 5 mm DSV. Three types of NbTi strands were used to reduce the cost of the superconducting materials. A preload with 80 MPa was exerted on the superconducting coils and over-banding with stainless steel was adopted to release the stress from the electromagnetic forces. The magnet will be operated in persistent mode with superconducting joints to reduce the field decay. The pulse tube cryocooler with a cooling capacity of 1 W at 4.2 K can be used to reduce the liquid helium evaporation and vibration during operation. The magnet will be equipped with Bi2223/AgAu HTS current leads to reduce the heat losses. In this paper, the design of the 9.4 T NMR superconducting coils, electromagnetic field calculations, and stress analysis of the superconducting coils were presented.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Pyridoxine is a versatile molecule that forms part of the family of B vitamins. It is used to treat and prevent vitamin B6 deficiency and certain type of metabolic disorders. Besides, pyridoxine molecule has been investigated as a suitable ligand toward metal ions. Nevertheless, the study of the magnetic properties of metal complexes containing lanthanide(III) ions and this biomolecule has been unexplored. We have synthesized and characterized a novel pyridoxine-based GdIII complex of formula [Gd(III)(pyr)2(H2O)4]Cl3 • 2 H2O (1) [pyr = pyridoxine]. 1 crystallizes in the triclinic system with space group Pī. In its crystal packing, the cationic [Gd(pyr)2(H2O)4]3+ entities are linked each other through H-bonding interactions involving non-coordinating water molecules and chloride anions. In addition, Hirshfeld surfaces of 1 were calculated to further investigate their intermolecular interactions in the crystal lattice. The study of the magnetic properties of 1 through ac magnetic susceptibility measurements reveals the occurrence of slow relaxation of magnetization in this mononuclear Gd(III) complex, this fact indicating an unusual single-ion magnet (SIM) behavior. We have also studied the relaxometric properties of 1, as a potential contrast agent for high-field MR imaging, from solutions of 1 prepared in physiological serum (0.0 - 3.2 mM range) and measured at 3 T on a clinical MR scanner. The relaxivity values obtained for 1 are larger than those of some commercial MR imaging contrast agents based on mononuclear Gd(III) systems

Grasslands are at risk of degradation due to unsustainable management practices and climate change. Sustainable grassland soil management can promote ecosystem service delivery and improve the resilience of the entire grassland ecosystem to anthropogenic change. Here, we re-view the principal soil quality indicators (SQIs) and how they have been used to evaluate the sustainability of different grassland management practices globally. We then discuss sustainable grazing management practices, before reviewing some novel grassland species which may im-prove grassland resilience with relevance for grassland management in Europe and the UK. We also give an overview of current sustainable grassland management methods and their assessment at field scale. From this, we suggest that sustainable Grazing Management Plans (GMPs), together with the testing of drought-resistant grass species and appropriate SQIs monitoring, is key to increasing resilience of grassland ecosystems to anthropogenic change.

COVID-19 infection, caused by SARS-CoV-2, is inequitably distributed and more lethal among populations with lower socioeconomic status. Direct contact with contaminated surfaces has been one of the virus sources, as it remains infective up to days. Several disinfectants have been shown to inactivate SARS-CoV-2 but they rapidly evaporate, are flammable or toxic and may be scarce or inexistent for the vulnerable populations. Therefore, we are proposing a simple, easy to prepare, low-cost and efficient antiviral films, made with wide available dishwasher detergent, which can be spread in hands and inanimate surfaces and maintains virucidal activity for longer periods than the current sanitizers. Avian coronavirus (ACoV) was used as model of challenge to test the antivirus efficacy of proposed films. Polystyrene microplates were covered with a thin layer of detergent formula. After drying, the films were exposed to different virus doses for 10 minutes and virus infectivity were determined using embryonated chicken eggs and RNA virus quantification in allantoic fluids by RT-qPCR. The films showed to inactive the ACoV (ranging from 103.66 to 106.66 EID50), which is chemically and morphologically similar to SARSCoV-2 and may constitute an excellent alternative to minimize the spread of Covid-19.

The urbanization effects on land surface phenology (LSP) have been investigated by many studies, but few studies focused on the temporal variations of urbanization effects on LSP. In this study, we used the MODIS EVI, MODIS LST data and China’s Land Use/Cover Datasets (CLUDs) to investigate the temporal variations of urban heat island intensity and urbanization effects on LSP in Northeast China during 2001–2015. Land surface temperature (LST) and phenology differences between urban and rural areas represented the urban heat island intensity and urbanization effects on LSP, respectively. Mann-kendall nonparametric test and Sen's slope were used to evaluating the trends of urbanization effects on LSP and urban heat island intensity. The results indicated that the average land surface phenology (LSP) during 2001–2015 was characterized by high spatial heterogeneity. The start of the growing season (SOS) in old urban area had become earlier and earlier than rural area and the differences of SOS between urbanized area and the rural area changed greatly during 2001–2015 (−0.79 days/year, p < 0.01). Meanwhile, the length of the growing season (LOS) in urban and adjacent areas had become increasingly longer than rural area especially in urbanized area (0.92 days/year, p < 0.01), but the differences of the end of the growing season (EOS) between urban and adjacent areas did not change significantly. Next, the UHII increased in spring and autumn during the whole study period. Moreover, the correlation analysis indicated that the increasing urban heat island intensity in spring contributed greatly to the increases of urbanization effects on SOS, but the increasing urban heat island intensity in autumn did not lead to the increases of urbanization effects on EOS in Northeast China.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

The direct measurements of the magnetic flux density in steel blocks within Compact Muon Solenoid (CMS) magnet yoke are performed with 22 flux loops installed in selected regions of the yoke. The 10,000-ton CMS magnet flux return yoke encloses a 4 T superconducting solenoid with a 6-m-diameter by 12.5-m-length free bore and consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end. The yoke steel blocks, mostly up to 620 mm thick, serve as the absorber plates of the muon detection system. A TOSCA 3-D model of the CMS magnet has been developed to describe the magnetic field everywhere outside of the tracking volume which was measured with a field-mapping machine. In the present study, for the first time, the reliable reconstruction of the magnetic flux density in the steel blocks of the yoke is performed using the CMS magnet standard discharges from the operational magnet current of 18.164 kA. To provide this reconstruction, the voltages induced in the flux loops (with amplitudes of 20–250 mV) have been measured with six 16-bit DAQ modules and integrated offline over time. The results of the flux loop measurements during three magnet ramp downs are presented and discussed.

Primary failure of eruption (PFE) is a rare non-syndromic condition involving total or partial non-eruption of posterior teeth, in the absence of mechanical obstruction. This paper presents the case of a healthy girl referred at age 4 years for asymmetry of upper arch. Clinical examination confirmed a slight shift of the upper midline to the left, with no erupted teeth distal to the upper left canine and left posterior open bite. Panoramic X-ray showed delayed intra-osseous development of lateral left upper teeth compared to the right side. Clinic and radiographic follow-up during the next 9 years showed that 26 has not erupted by almost 13 years of age, 27 has delayed development and an unusual shape and there is agenesis of 24, 25. Genetic analysis using the PTH1R single gene sequencing did not detect any known disease-causing or rare pathogenic variants that could explain the patient's phenotype. Even when detected early, PFE rises difficult problems with regard to diagnosis and ortho-surgical treatment planning due to the impossibility to accurately predict the evolution. Tooth agenesis on the same arch worsens the prognosis and adds challenges to planning the treatment. Close long-term follow-up and timely adjustment of treatment plan in accordance to the evolution of the case are needed.

Successful fertilization treatments targeted to improve stand productivity while reducing operational complexities and cost depend on a clear understanding of soil nutrient availability under varying environmental conditions. Soil nutrient data collected from 154 forest sites throughout the Inland Northwest, USA were analyzed to examine soil nutrient characteristics on different geologic soil parent materials and to rank soil fertility. Results show that soil parent material explains significant differences in soil nutrient availability. Soils developed from volcanic rocks have the highest CEC and are relatively high in P, K, S, Mg, Cu, Ca, and B, but generally poor in N. Forest soils developed from plutonic rocks exhibit the lowest CEC and are low in N, S, K, Mg, Cu, and Ca, but higher in P. Some soils located on mixed glacial till are low only in K, Cu, Mg, and Ca, but many glacial soils are relatively rich in other nutrients, albeit the second lowest CEC. Soils developed from metasedimentary and sedimentary rocks are among those with lowest soil nutrient availability for P and B. Sulfur was found to have the highest concentrations in metasedimentary influenced soils and the least in sedimentary derived soils. Our results should be useful in designing site-specific fertilizer and nutrient management prescriptions for forest stands growing on soils developed from these major geologies within the Inland Northwest region of the United States.

In the recent years, biochar has emerged as a remarkable biosourced material for addressing global environmental, agricultural, biomedical, and energy challenges. However, the performances of biochar rest in part on finely tuning its surface chemical properties, intended to obtain specific functionalities. In this review, we tackle surface treatment of biochar with silane and other coupling agents such as diazonium salts, titatantes, ionic/non-ionic surfactants, as well as nitrogen-containing (macro)molecules. We summarize the recent progress achieved mostly in the last five years, and correlate the nature and extent of functionalization to eye catchy end applications of the surface engineered biochar.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

This study used the ECOSSE model (v. 5.0.1) to simulate soil respiration (Rs) flux-es estimated from ecosystem respiration (Reco) for eight European permanent grassland (PG) sites with varying grass species, soils, and management. The main aim was to evaluate the strengths and weaknesses of the model in estimating Rs from grasslands, and to gain a better understanding of the terrestrial carbon cycle and how Rs is affect-ed by natural and anthropogenic drivers. Results revealed that the current version of the ECOSSE model may not be reliable for estimating daily Rs fluxes, particularly in dry sites. However, it could still be a valuable tool for predicting cumulative Rs from PG. Additionally, the model demonstrated accurate simulation of Rs in response to grass cutting and slurry application practices. The sensitivity analyses and attribution tests revealed that increased soil organic carbon (SOC), soil pH, temperature, reduced precipitation, and lower water table (WT) depth could lead to increased Rs from soils. The variability of Rs fluxes across sites and years was attributed to climate, weather, soil properties, and management practices. The study suggests the need for additional development and application of the ECOSSE model, specifically in dry and low input sites, to evaluate the impacts of various land management interventions on carbon sequestration and emissions in PG.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

In this study, we investigated the effects of three surface treatment techniques on 316L stainless steel, low-temperature immersion corrosion, shot peening followed by immersion corrosion, and electrochemical corrosion. Surface alterations were analyzed using scanning electron microscopy, Raman spectroscopy, and α-step thin-film thickness profiling. Human osteoblast adhesion was evaluated using Liu’s stain and metallographic optical microscopy. The results revealed weak cell adhesion after low-temperature immersion and shot peening followed by immersion corrosion. By contrast, electrochemical corrosion, particularly with a high current density and low corrosive solution concentration, resulted in a uniformly corroded surface, thus promoting dense cell adhesion. All three techniques resulted in porous oxide layers. Overall, our experimental findings highlighted shot peening (1 kg/cm2 for 20 s) and electrochemical corrosion (0.5 M HCl) as effective processes. Electrochemical corrosion produced uniformly dense corrosion pits, whereas shot peening produced semicircular grooves with small corrosion pits, both favorable for cell adhesion. Electrochemical corrosion also yielded excellent cell adhesion, emphasizing its suitability for biomedical activity. We developed a process for creating a porous surface layer and thereby enhancing the cell adhesion to 316L stainless steel for potential biomedical implant applications.

Persistent land subsidence or uplift can cause serious latent hazards to urban infrastructure. To thoroughly investigate the causes and impacts of land surface deformation, this study examines the case of Wuxi City, focusing on the land fluctuation patterns in the region following the enforcement of the groundwater abstraction prohibition policy in 2005. This research utilizes the PS-InSAR technique to quantify land surface deformations in the Wuxi region from November 2015 to June 2023 and analyzes 100 SAR images to obtain comprehensive spatiotemporal evolution data of the land surface. Furthermore, this study conducts an in-depth analysis of the effects of various factors, including groundwater, precipitation, and soil geology, on the characteristics of land surface deformation. It pioneers the application of the GARCH (Generalized Autoregressive Conditional Heteroskedasticity) model to analyze the time-series displacement in the study area and innovatively introduces the "amplitude factor" index to assess land surface fluctuations. This study investigates the recent land surface deformation patterns and mechanisms in Wuxi City. By integrating the "amplitude factor", it provides a scientific foundation for future urban development and disaster mitigation strategies in Wuxi City, offering valuable insights for related research.

SmCo5 constitutes one of the strongest class of permanent magnets, which exhibit enormous uniaxial magnetocrystalline anisotropy energy and have a high Curie temperature. However, the performance of SmCo5 permanent magnets is hindered by a limited energy product and relatively high supply risk. Sm is a moderately expensive element among its group, and Co is a material more expensive than Fe, making SmCo5 magnets the most expensive class of permanent magnets. Subsequently, the need for new materials, with less content in critical and thus expensive resources, is obvious. A promising path of producing new compounds that meet these requirements is the chemically modification of established materials used in PM towards the reduction of expensive resources, for example reducing Co content with transition metals (like Fe, Ni) or using as substitutes raw rare earth materials with abundance greater than their demand, like Ce and La. Important instrument to achieve these goals are theoretical calculations, like Ab-initio methods, and especially DFT based calculations in predicting the possible stable RE-TM intermetallic compounds and their magnetic properties. This review aims to present the progress of recent years in the production of improved SmCo5 type magnets.

It is necessary to manage the power consumption and use fault-tolerance techniques to meet high reliability in Real-Time Embedded Systems, . Hence, in recent years, this is the main reason for providing an ideal approach to decrease power consumption through the worst-case behavior of instantaneous power management (peak-power management), while observing the Thermal Design Power (TDP). Although the multi-core chips in real-time embedded systems provide great opportunity for implementation of Two-phase Triple modular redundancy to meet high reliability, the energy overhead management of concurrently executing tasks is one of the challenges facing designers. In this article, we propose a scheme named Permanent Fault Aware, Two-Phase Peak-Power Management (PFA-TP3M), for scheduling real-time tasks in multi-core systems to eliminate peak power overlap from concurrent running tasks to maintain peak power consumption at the chip TDP. and through mapping different parts of each task on separate cores, prevents consecutive conflicts on cores, which have faced permanent faults to design the fault-tolerant system. Our simulation results show that our proposed scheme provides up to 700x fault tolerance increase (630x on average) compared to the state-of-the-art power management algorithm, an achievement costs up to 14%. (average 11%) increase the length of the task graph compared to it.

The extrusion-based 3D concrete printing (3DCP) technology allows the fabrication of permanent formwork with intricate shapes, into which fresh concrete is cast to build structural members with complex geometry. This significantly enhances the geometric freedom of concrete structures without the use of expensive temporary formwork. In addition, with proper material choice for the permanent formwork, the load-bearing capacity and durability of the resulting structure can be improved. This paper investigates 3DCP of permanent formwork for reinforced concrete (RC) beam construction. A 3D-printable engineered geopolymer composite (3DP-EGC, or strain-hardening geopolymer composite, 3DP-SHGC) recently developed by the authors was used for fabrication of the permanent formwork. The 3DP-EGC exhibits strain-hardening behaviour under direct tension. Two different printing patterns were used for the soffit of the permanent formwork to investigate the effect of this parameter on the flexural performance of RC beams. A conventionally mould-cast RC beam was also prepared as the control beam for comparison purposes. The results showed that the RC beams constructed using the 3DP-EGC permanent formwork exhibited superior flexural performance to the control beam. Such beams yielded significantly higher cracking load (up to 43%), deflection at ultimate load (up to 60%), ductility index (50%) and absorbed energy (up to 107%) than those of the control beam. The ultimate load was comparable with or slightly higher than that of the control beam. Furthermore, the printing pattern at the soffit of the permanent formwork was found to have a significant influence on the flexural performance of the RC beams.

Firstly, a new set of Quasi-Cubic Trigonometric Bernstein basis with two tension shape parameters is constructed, and we prove that it is an optimal normalized totally basis in the framework of Quasi Extended Chebyshev space. And the Quasi-Cubic Trigonometric Bézier curve is generated by the basis function and the cutting algorithm of the curve are given, the shape features (cusp, inflection point, loop and convexity) of the Quasi-Cubic Trigonometric Bézier curve are analyzed by using envelope theory and topological mapping; Next we construct the non-uniform Quasi-Cubic Trigonometric B-spline basis by assuming the linear combination of the optimal normalized totally positive basis have partition of unity and continuity, and its expression is obtained. And the non-uniform B-spline basis is proved to have totally positive and high-order continuity. Finally, the non-uniform Quasi Cubic Trigonometric B-spline curve and surface are defined, the shape features of the non-uniform Quasi-Cubic Trigonometric B-spline curve are discussed, and the curve and surface are proved to be continuous.

Blood has certain significant physical properties, which the authors investigated. This paper provides values of surface tension and viscosity of blood at 37 °C, as well as relationship between them plotted on a cross-plot. By applying Hagen- Poiseuille equation and Jurin's law to the experimentally obtained data, the authors calculated with great accuracy viscosity and surface tension of blood. Evaluating both of the properties using described methods required from the authors to know the density of investigated liquid, which was found to be on average $\rho=1063,56 \frac{kg}{m^3}$. The authors took blood samples from 30 healthy subjects and determined aforementioned physical properties. There has been made a distinction in regard of a sex of the blood donor. Results indicate that both surface tension and viscosity are independent from sex of a subject, as well as indicate that there is no correlation between viscosity and surface tension of blood at 37\degree C. Average values of surface tension and viscosity were found to be $\sigma=5,241\pm 0,262 \cdot 10^{-2}\frac{J}{m^2}$ and $\eta=3,352\pm0,360 \cdot 10^{-3} Pa \cdot s$, respectively.

: Since the COVID-19 pandemic, people have become aware that materials (products) can transmit infection and have begun to focus on questions such as how bacteria and germs, the sources of in-fection, maintain their infectivity on material surfaces, and the extent to which materials can or cannot prevent this. and to what extent materials can and cannot prevent it. The SIAA, a non-profit organization of many Japanese companies, had created an entirely separate interna-tional standard for materials' antibacterial, antiviral, and antibiofilm properties (products). The authors have studied the academic basis for the operation of the standards and were deeply in-volved as researchers in establishing one of the standards. This paper describes the interna-tional standards and some representative examples of the authors' actual use of these standards and explains the current status and future problems.

Abstract Objective: To review the relevant literature on the use of atrioventricular node ablation and pacing in patients with heart failure and atrial fibrillation. Methods: A PubMed/MEDLINE and SCOPUS search was performed in order to assess the clinical outcomes of atrioventricular node ablation and pacemaker implantation, as well as the complications that may occur. Results: Several clinical trials, observational analyses and meta-analyses have shown that “pace and ablate” strategy not only improves symptoms but also can enhance cardiac performance in patients with heart failure and atrial fibrillation. Although this procedure is effective and safe, some complications may occur including worsening of heart failure, permanent fibrillation, arrhythmias and sudden death. Regarding the implantation of pacemaker, cardiac resynchronization therapy is shown to be the optimal choice compared to right ventricle apical pacing. His bundle pacing is a promising alternative to cardiac resynchronization therapy and has shown beneficial effects, while left bundle brunch pacing is an innovative modality. Conclusions: Atrioventricular node ablation and implantation of pacemaker is shown to have beneficial effects on clinical outcomes of patients with atrial fibrillation ± heart failure who do not respond or are intolerant to medical treatment. Cardiac resynchronization therapy is the treatment of choice and His bundle pacing seems to be an effective alternative way of pacing in these patients.

Mn-promoted bulk iron catalysts with high specific surface area (82-211 m2.g-1) were synthesized by coprecipitation followed by drying under supercritical conditions. The catalysts were tested in the CO2 hydrogenation reaction. The Mn-promoted iron catalysts showed better textural properties than the bare Fe2O3 catalyst, allowing better dispersion of the active phase, easier reduction of iron oxide, better carburization of iron oxides and higher catalytic activity than the bare Fe2O3 catalyst. The best activity results were obtained by catalyst promotion with a very low amount of Mn (Mn/Fe ratio of 0.05). Upon steady-state conditions (T=340 ºC, total pressure of 20 bar and H2/CO2=3), this catalyst showed high CO2 conversion (44.2%) and selectivity to C2-C4 hydrocarbons (68%, olefin to paraffin ratio of 0.54), while the selectivity to C5+ hydrocarbons, CH4 and CO was about 3.2, 38.5 and 5%, respectively. A close correlation was found between catalyst textural properties and CO2 conversion. The most active MnFe-0.05 catalyst shows high stability during 72 h of reaction related to low amount of soft coke formation and catalyst activation through the formation of χ-Fe5C2 phase during the on-stream reaction.

The present work proposes a novel manufacturing technique based on the combination of Laser Metal Deposition, Laser Beam Machining and Laser Polishing processes for the complete manufacturing of complex parts. Therefore, the complete process is based on the application of a laser heat source both for the building of the preform shape of the part by additive manufacturing and for the finishing operations. Their combination enables to manufacture near-net-shape parts and afterwards, remove the excess material via laser machining, which has resulted to be capable of eliminating the waviness resulting from the additive process. Besides, surface quality is improved via laser polishing to reduce the roughness of the final part. Therefore, conventional machining operations are eliminated, what results in a much cleaner process. In order to validate the capability of this new approach, the dimensional accuracy and surface quality of the resulting parts are evaluated. The process has been validated on an Inconel 718 test part, where a previously additively built up part has been finished by means of laser machining and laser polishing.

A partial or complete pulpotomy is a type of vital pulp therapy (VPT) that aims to remove the in-flamed, infected pulp, leaving behind healthy, vital pulp that is capable of healing. VPT has gained renewed popularity as a treatment option in permanent mature posterior teeth with irre-versible/moderate-severe pulpitis, its high success rates matching that of root canal treatment (RCT). There is currently no consensus regarding diagnostic and prognostic predictors of success of pulpotomies for managing such cases. Therefore, we conducted a scoping review to identify and analyze how these factors affect the outcome of treatment. A literature search using the PRISMA guidelines was undertaken using PubMed and Scopus on July 7, 2023. A total of 22 studies met the inclusion criteria and were qualitatively analyzed by two reviewers. The follow-ing diagnostic and prognostic factors were recognized and discussed; presenting signs and symptoms, periapical diagnosis, bleeding time, indicators of inflammation (bleeding time, con-centration of inflammatory biomarkers), patient age and medical status, the depth, activity and location of caries, and restorative factors. Based on the studies assessed, there is limited evidence to support their prognostic value. Further research is necessary to identify solid predictors of outcome.

Background: Permanent Daylight Savings Time (DST) may improve road safety by providing more daylight in the evening but could merely shift risk to morning commutes or increase risk due to fatigue and circadian misalignment. Methods: To identify how potential daylight exposure and fatigue risk could differ between permanent DST versus permanent Standard Time (ST) or current time arrangements (CTA), generic work and school schedules in five United States cities were modeled in SAFTE-FAST biomathematical modeling software. Commute data were categorized by morning (0700-0900) and evening (1600-1800) rush hours. Results: Percent darkness was greater under DST compared to ST for the total waking day (t=2.59, p=0.03) and sleep periods (t=2.46, p=0.045). Waketimes occurred before sunrise 63%±41% percent of the time under DST compared to CTA (42%±37%) or ST (33%±38%; F(2, 74)=76.37; p<0.001). Percent darkness was greater during morning (16%±31%) and lower during evening rush hour (0%±0%) in DST compare to either CTA (morning:7%±23%; evening:7%±14%) or ST (morning:7%±23%; evening:7%±15%). Discussion: Morning rush hour overlapped with students’ commutes and shift worker reverse commutes, which may increase traffic congestion and risk compared to evening rush hour. Switching to permanent DST may be more disruptive than either switching to ST or keeping CTA without noticeable benefit to fatigue or potential daylight exposure.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

At present, nanomaterials (NMs) show extreme potential for a wide range of applications ranging from aerospace to energy storage applications owing to a number of properties which, in a number of contexts have been reported to be superior as compared to those of bulk counterparts. However, the high surface area to volume ratio which yields extraordinary properties to NMs also turns out to be the major limitation in a number of different contexts. For instance, the high surface area to volume ratio in these materials leads to a high reactivity, especially in electrochemical environments which are prevalent during energy storage applications. In this context, it is worthwhile mentioning that processing of NMs play a crucial role in influencing their mechanical properties. On the other hand, surface engineering has emerged as a powerful tool to deconvolute bulk properties from surface characteristics and has been reported to exhibit tremendous potential for overcoming the aforementioned limitation of NMs. The present review therefore, is aimed at highlighting the present status of research in the field of processing and applications of surface engineered NMs. Moreover, challenges and future perspectives in the aforementioned avenue have been discussed.

The results of a study of the processes of formation of macro- and micro-inhomogeneity of ingots and rolled sheets are presented. To study the nature and sources of surface defects in rolled sheets, a comparative method of structural-concentration analysis of metal at the end-to-end metallurgical process of ingot - slab - sheet metal has been developed, based on the metallographic method of studying the structure and qualitative analysis of non-metallic inclusions. The research results showed that the quality of the surface of rolled sheets is determined mainly by the physical heterogeneity of the crust zone of the ingots, and the internal defects of thin rolled sheets largely depend on the contamination of the metal with non-metallic inclusions and off-axis segregation. A mechanism for transforming defects in the casting cortical zone into surface and internal defects in rolled sheets is proposed.

Patients undergoing dialysis through a permanent catheter often experience infection or malfunction. However, few studies have clarified the predictors of permanent catheter patency survival in patients undergoing hemodialysis. We assessed the relationship between parameters of body composition monitoring (BCM) determined before the initiation of dialysis and the patency survival of the permanent catheters inserted in 179 patients who commenced hemodialysis between January 14, 2020 and August 31, 2021. The relationships between permanent catheter patency at 6 weeks and BCM parameters, laboratory tests, age, sex, comorbidities, and medications at baseline were studied using Kaplan–Meier survival curves. Permanent catheter patency was observed to be superior at high extracellular-to-intracellular (ECW/ICW) ratio (P<0.005). After adjustment for covariates, the ECW/ICW ratio remained an independent factor associated with permanent catheter patency survival. When patients with non-patent catheters were subdivided into infection and malfunction groups, and the associations of BCM parameters were evaluated in those groups, the ECW/ICW ratio was not significantly associated with permanent catheter patency survival in the infection group (P = 0.327); instead, a significant association was found for the lean tissue index (P<0.001). In the malfunction group, the ECW/ICW ratio remained significantly associated with permanent catheter patency survival (P < 0.001).

Conventional methods of crop mapping need ground truth information to train the classifier. Thanks to the frequent acquisition allowed by recent satellite missions (Sentinel 2), we can identify temporal patterns that depend on both phenology and crop management. Some of these patterns are specific to a given crop and thus can be used to map it. Thus, we can substitute ground truth information used in conventional methods with agronomic knowledge. This approach was applied to identify irrigated permanent grasslands (IPG) in the Crau area (Southern France) which play a crucial role in groundwater recharge. The grassland is managed by making three mows during the May-October period which leads to a specific temporal pattern of leaf area index (LAI). The mowing detection algorithm was designed using the temporal LAI signal derived from Sentinel 2 observations. The algorithm includes some filtering to remove noise in the signal that might lead to false mowing detection. A pixel is considered a grassland if the number of detected mows is greater than 1. A data set covering five years (2016-2020) was used. The detection mowing number was done at the pixel level and then results are aggregated at the plot level. A validation data set including 780 plots was used to assess the performances of the classification. We obtained a Kappa index ranging between 0.94-0.99 according to the year. These results were better than other supervised classification methods that include training data sets. The analysis of land-use changes shows that misclassified plots concern grasslands managed less intensively with strong intra-parcel heterogeneity due to irrigation defects or year-round grazing. Time series analysis, therefore, allows us to understand different management practices. Real land-use change in use can be observed, but long time series are needed to confirm the change and remove ambiguities with heterogeneous grasslands.

Objectives: The purpose of the study was to evaluate the effectiveness of dental caries segmentation on the panoramic radiographs taken from children in primary dentition, mixed dentition, and permanent dentition with an Artificial Intelligence (AI) models developed using the deep learning method. Methods: This study used 6075 panoramic radiographs taken from children aged between 4 and 14 to develop the AI model. The radiographs included in the study were divided into three groups as primary dentition (n: 1857), mixed dentition (n: 1406), and permanent dentition (n: 2812). U-Net model implemented with PyTorch library was used for segmentation of caries lesions. Confusion matrix was used to evaluation of model performance. Results: In the primary dentition group, the sensitivity, precision and F1 scores calculated using the confusion matrix were found to be 0.8525, 0.9128, and 0.8816, respectively. In the mixed dentition group, the sensitivity, precision, and F1 scores calculated using the confusion matrix were found as 0.7377, 0.9192, and 0.8185, respectively. In the permanent dentition group, the sensitivity, precision, and F1 scores calculated using the confusion matrix were found as 0.8271, 0.9125, and 0.8677, respectively. In the total group including primary, mixed, and permanent dentition, the sensitivity, precision and F1 score calculated using the confusion matrix were 0.8269, 0.9123 and 0.8675, respectively. Conclusion: Deep learning-based AI models are promising tools for the detection and diagnosis of caries in panoramic radiographs taken from children in different dentitions.

There is a considerable increase in the use of substances and medical procedures aimed at changing the esthetics of the face, particularly the appearance of the lips. Permanent fillers such as polydimethylsiloxane, also called liquid silicone, are widely used, but their application for facial esthetics is currently obsolete. However, the long-term complications remain a reality, as they can occur decades after the application. Thus, the goal of this case report was to present a complication after 16 years of treatment using liquid silicone. This case report involved a 52-year-old male with a complication of bilateral permanent filler in the upper lip performed 16 years ago, its surgical removal, and histological analysis. Histologically, it was possible to identify a chronic inflammatory, lymphoplasmacytic, and granulomatous reaction, with foreign body giant cells’ reaction, in relation to non-polarizable exogenous material due to the reaction to silicone. The most common complications are granulomas' appearance and material displacement. The case report shows these granulomas are characterized as chronic low-caliber inflammation around the silicone. They have an unknown etiology but are probably multifactorial, from continuous trauma, friction or irritation, iatrogenic factors, infection, immunological mechanisms, and genetic and molecular variations, and can be highly related to the impurity of the injected material.

In order to improve the wear resistance of copper contacts in high-voltage switches and improve the abnormal discharge phenomenon caused by wear gaps, laser remelting technology was used to strengthen the surface of copper contacts. The surface morphology, microhardness, and wear resistance of the remelted samples were tested and characterized using scanning electron microscopy (SEM), microhardness tester, and friction and wear tester. The test results indicate that laser frequency, pulse width, and current parameters can directly affect the surface morphology and wear resistance of the sample, but their influencing processes vary. The laser frequency is achieved by the variation of the superposition relationship between the impact points, while the pulse width and current are achieved by the variation of the laser intensity at the impact points. When the pulse frequency is 10Hz, the pulse width is 10ms, and the current is 100A, the sample exhibits a more balanced surface morphology, microhardness, and wear resistance.

In previous studies regarding the osseointegration of zirconia (ZrO2) implants, a lack of consistency was observed in the surface topographies of the ZrO2 and Ti samples because of the difficult processability of ZrO2 surfaces. To resolve this problem, we used the molecular precursor method (wet process), which is a surface-modifying technique that can easily change the surface chemistry without changing the surface topography. A roughened Ti surface was prepared using sandblasting (large-grit) and acid treatment. We were able to create ZrO2-coated Ti implants with the same topography as that of roughened Ti substrates using the molecular precursor method, which solution contained a Zr complex. The uniform presence of tetragonal Zr was confirmed, and the apparent zeta potential of the surface of the ZrO2-coated Ti implant was higher than that of Ti. In animal experiments, ZrO2-coated Ti implants showed an equivalent or higher bone-to-implant contact ratio compared to that of the non-coated implants inserted into the femur bone defects of the rats. ZrO2 with the same surface topography as that of roughened Ti exhibits a promotion of osteogenesis equivalent to or better than that of Ti in the early stages of bone formation.

Traditional ways of validating satellite-derived sea surface temperature (SST) and sea surface salinity (SSS) products, using comparisons with buoy measurements, do not allow for evaluating the impact of mesoscale to submesoscale variability. Here we present the validation of remotely-sensed SST and SSS data against the unmanned surface vehicle (USV) – Saildrone – measurements from the Spring 2018 Baja deployment. More specifically, biases and root mean square differences (RMSD) were calculated between USV-derived SST and SSS values, and six satellite-derived SST (MUR, OSTIA, CMC, K10, REMSS, and DMI) and three SSS (JPLSMAP, RSS40, RSS70) products. Biases between the USV SST and OSTIA/CMC/DMI were approximately zero while MUR showed a bias of 0.2C. OSTIA showed the smallest RMSD of 0.36C while DMI had the largest RMSD of 0.5C. An RMSD of 0.4C between Saildrone SST and the satellite-derived products could be explained by the daily variability in USV SST which currently cannot be resolved by remote sensing measurements. For SSS, values from the JPLSMAP product showed saltier biases of 0.2 PSU, while RSS40 and RSS70 showed fresh biases of 0.3 PSU. An RMSD of 0.4 PSU could not be explained solely by the daily variability of the USV-derived SSS. Coherences were significant at the longer wavelengths, with a local maximum at 100 km that is most likely associated with the mesoscale turbulence in the California Current System.

Abstract: This review presents current literature on different nanocomposites coatings and surface finishing for different substrates (such as textiles, concrete, plastics, stones, metals and so on). In particular, this study is focused on smart materials, drug delivery systems, and industrial, antifouling and nano/ultrafiltration membrane coatings. Each of these nanostructured coatings shows interesting properties for different fields of application. In this review, particular attention is paid to the synthesis and the consequent physico-chemical characteristics of each coating and, therefore, to the different parameters that influence the substrate deposition process. Several techniques used in the characterization of these surface finishing coatings are also described. In this review, the sol-gel and polymerization method for preparing stimuli-responsive coatings as smart sensor materials is described; functional polymers and nanoparticles sensitive to pH, temperature, phase, light and biomolecules are also treated. Finally, nanomaterials based on phosphorus, borates, hydroxy carbonates and silicones are used and described as flame retardant coatings; organic/inorganic hybrid sol-gel coatings for industrial applications are illustrated, together with functional nanofiller (carbon nanotubes, metallic oxides, etc.) and polymers employed for nano/ultrafiltration membrane and antifouling coatings. In the last decades, several research institutes and industries have collaborated for the advancement of nanotechnology by optimizing conversion processes of conventional materials into coatings with new functionalities for intelligent, innovative, eco-sustainable and advanced applications.

Good hand hygiene has proven to be essential in reducing the uncontrolled spread of human pathogens. Cold atmospheric plasma (CAP) may provide an alternative to disinfecting hands with ethanol-based handrubs when hand washing facilities are unavailable. CAP can be safely applied to the skin if the energy is well controlled. In this study, RF and DC plasma sources was built with a pin-to-mesh electrodes configuration inside a fused silica tube of 5 mm of inner diameter. Microbiological assays based on EN 13697:2015+A1:2019 using Escherichia coli DSM 682 or Staphylococcus epidermidis DSM 20044 were used to examine the antimicrobial effect of various plasma conditions. Metal and silicone disks that model skin were used as inoculation matrices. The prototype air radio frequency (RF) CAP achieved significant disinfection in the MHz range on stainless steel and silicone substrates. This is equivalent to half the performance of direct current CAP, which is only effective on conductive substrates. Using only electricity and air CAP could, with further optimization, replace or complement current hand disinfection methods, and mitigate the economic burden of public health crises in the future.

The paper presents a simplified laminar model with which the deformation of soil layers (base, subbase and subgrade courses) under flexible pavements due to repeated traffic load can be determined. In the first step, the cyclic strain amplitude is calculated using a nonlinear material model that is based on particle size distribution parameters (d50 and CU) and dependent on the mean normal stress, relative density and actual strain level. In the second step, the HCA (High Cycle Accumulation) model is used to calculate the residual settlement of each sublayer as a function of the number of cycles. It is shown that the developed model is suitable for describing different types of subgrades and pavement cross-sections. It is also demonstrated with finite element calculations that the developed model describes both the elastic and plastic strains sufficiently accurately. The developed model can predict the settlement and rutting of pavement structures with sufficient accuracy based on easily available particle size distribution parameters without the need of complex laboratory and finite element tests.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

Herein, we describe precisely on covalent modification of pure magnesium (Mg) surface and applied to induce in vitro osteogenic differentiation. A new concept, chemical bonding method is proposed for developing stable chemical bonds on Mg surface through serial assembly of bioactive additives including ascorbic acid (AA) and bovine serum albumin (BSA). The coating with such potential materials shows strong integrity to the Mg and could suitable for cell-interface interaction with the host tissue during implantation in bone tissue repair. The physicochemical and electrochemical properties of surface modified Mg assess how these nanoscales layered of biomolecules could demonstrate the significance improvement in chemical stability of coating. The modified Mg-OH-AA-BSA exhibits better anti-corrosion behavior with high corrosion potential (Ecorr ~ ‒ 0.96 V) and low corrosion current density (Icorr ~ 0.2 µA cm-2) as compared to pure Mg (Ecorr ~ ‒1.46 V, Icorr ~ 10.42 µA cm-2). Outer layer of BSA on Mg protects fast degradation rate of Mg which is the consequence of strong chemicals bonds between amine groups on BSA with carboxylic groups on AA. Collectively, the results suggest that surface modified Mg provides strong bio-interface and enhances the proliferation and differentiation of pre-osteoblast (MC3T3-E1) cells through protein-lipid interaction. Owing to this fact, the cost-effective and scalable covalent functionalization of Mg surface inherits biological advantage in orthopedic and dental implants with long term stability.