The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

In areas with a deep floor plan, the distribution of natural light is not uniform. Consequently, relying solely on daylight may not suffice to meet the space's lighting requirements, necessitating the use of artificial lighting in darker areas. Therefore, a lighting system is needed that not only controls the glare near the windows but also increases the light at the end of the room and provides uniform daylight. One of the widely used systems is the “light shelf“which has three main functions: shading, increasing the depth of light penetration and reducing glare. Review articles about light shelves have been done in 2015 and 2017, while more than 80% of the studies have been carried out since 2016 and light shelves with more diverse forms and dynamic elements and many consolidations were proposed. Therefore, there is a need for a more comprehensive review. The main question of this research is how different parameters (including climate, material, ceiling and integrated systems) can help to increase the efficiency of light shelves. By using a systematic review, studies in the past three decades were classified in order to determine the effect of these parameters on improving lighting performance and controlling solar heat gain.

Buildings are responsible for approximately 40% of global energy consumption, putting pressure on the construction industry to mitigate its environmental impact. Therefore, there is an urgent need for innovative solutions to reduce power consumption, particularly in lighting systems. The study’s primary objective was to investigate novel integrated lighting solutions that significantly reduce energy use and they explore their enhancement through Building Information Modeling (BIM) and the Internet of Things (IoT) to further improve energy efficiency and reduce the carbon footprint in buildings. Hence, this literature review aimed to examine energy-saving actions, retrofitting practices and interventions across a range of multi-use buildings worldwide over the past six years. The objective was to diagnose the goals being undertaken and ultimately validate new actions and contributions to minimise energy consumption. First, daylight harvesting and retrofitting solutions were examined in conjunction with the latest technologies, also referred to the external shadings. In consequence of this matter, comes the lack or unappropriated coordination, and so waste of energy, between daylight and electrical lighting. Secondly, how the integration of BIM facilitates the design process, providing a complete overview of all the variables of the building, thus improving indoor daylight performance and proper lighting with energy analysis. Lastly, the review addresses the role of IoT in providing real-time data from sensor networks, allowing for continuous monitoring of building conditions. This systematic literature review explores the integration of the fields to address the urgent need for innovative strategies and sustainability in the built environment. Furthermore, it thoroughly analyses the current state of the art, identifying best practices, emerging trends and concrete insight for architects, engineers, and researchers. The goal is to promote the widespread adoption of low-carbon systems and encourage collaboration among industry professionals and researchers to advance sustainable building design.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

Published data or available literature on sustainable building plan-design, construction, performance, and renovation criteria have covered some stages or some parts of each stage. These data usually have been published partially in many different papers―there have not been any papers that published these data together. Hence, this paper aims to collectively review these data and publish them together. The collection and review of these data were carried out by our twenty-five team members who specialized in sustainable urban, architectural, and civil engineering and construction management. The gathered and reviewed outputs were combined and validated based on a general group consensus. This consensus decision-making proceeded through two major group meetings with several follow-up meetings. The first major meeting was to combine and improve the gathered reviewed sustainable building criteria for Cambodia. The second major meeting was to validate the improved reviewed sustainable building criteria for Cambodia. The several follow-up meetings were to discuss the relevance and importance of the validated data “criteria and their classifications and descriptions” in all stages and more focused on their importance and applicability to Cambodia. The collective reviewed data in this paper would be useful to researchers in the fields. They could also be useful collective knowledge and information for policymakers from governmental agencies and development partners, particularly for sustainable building and construction companies.

With buildings accounting for a significant portion of global energy consumption and greenhouse gas emissions, the application of artificial intelligence (AI) holds promise for enhancing sustainability in the building lifecycle. This systematic literature review addresses the current understanding of AI's potential to optimize energy efficiency and minimize environmental impact in building design, construction, and operation. A comprehensive literature review and synthesis were conducted to identify AI technologies applicable to sustainable building practices, examine their influence, and analyze the challenges of implementation. The review was guided by a meticulous search strategy utilizing keywords related to AI application in sustainable building design, construction, and operation. The findings reveal AI's capabilities in optimizing energy efficiency through intelligent control systems, enabling predictive maintenance, and aiding design simulation. Advanced machine learning algorithms facilitate data-driven analysis and prediction, while digital twins provide real-time insights for informed decision-making. Furthermore, the review identifies barriers to AI adoption, including cost concerns, data security risks, and challenges in implementation. AI presents a transformative opportunity to enhance sustainability in the built environment, offering innovative solutions for energy optimization and environmentally conscious practices. However, addressing technical and practical challenges will be crucial for the successful integration of AI in sustainable building practices.

In light of the accelerated pace of economic growth and urbanisation, the transformation of green buildings has emerged as a prominent area of re-search. A considerable number of existing buildings have been constructed and are still in use. However, the energy consumption and environmental impact throughout the entire life cycle of these buildings are not adequately considered in the renovation design. This results in high energy consumption and poor indoor comfort. In this work, we include improving the thermal insulation of buildings, such as thickening the insulation of external walls and replacing energy-efficient windows to reduce energy losses caused by temperature differences between in-door and outdoor buildings; Adopt energy-efficient HVAC systems to reduce en-ergy consumption and improve indoor air quality by upgrading equipment effi-ciency, optimizing duct design, and intelligent control systems; At the same time, we will introduce renewable energy sources such as solar energy, and we will not only install solar photovoltaic panels to generate electricity, but also use solar thermal collector systems to provide hot water and heating, so as to achieve di-versified and sustainable use of energy. Combined, these measures can effec-tively reduce the overall energy consumption of the building, reduce carbon emissions, and improve the comfort and health of the indoor environment. During the experimental analysis, the energy consumption and indoor comfort before and after the renovation were evaluated, and the results showed that the energy consumption was significantly reduced and living comfort was improved.

Ming-style round-backed armchairs as a classic Chinese chair design are renowned for the blend of ergonomics, practicality, and elegance. Although the Chinese armchair furniture industry has made strides in sustainability, there is still a need for further improvements in material selection, manufacturing processes, and supply chain management to fully support the development of sustainable furniture. Laminated bamboo lumber as new sustainable materials are becoming a popular option for furniture designers in the era of "sustainable design". This research aims to investigate the feasibility and application of laminated bamboo lumber in the design of Chinese armchair furniture and proposes innovative ideas for optimizing the armchair's design. First, an empirical study was conducted to comprehensively understand the classification of Ming-style round-backed armchairs’ structure to develop a 3D model. Secondly, an experimental research method was then employed to explore the parameters of laminated bamboo lumber for future studies. Additionally, a validation experiment was conducted to compare real-world scenarios with simulations using finite element analysis in Ansys. Finally, finite element analysis was used to test the feasibility and application of laminated bamboo lumber in furniture design, focusing on the material’s mechanical properties. Results indicated that laminated bamboo lumber has excellent mechanical properties as furniture design materials, subsequently, using the optimized results, the use of 0.6319 kg of steel was successfully reduced by 23.68% to ensure the armchair’s stability. This provides a reference for the future compter-assist and standardized innovative design of Chinese armchair. By incorporating compter-assist design and lightweight optimization, it is possible to save materials and make more efficient use of resources, thereby contributing to sustainable development goals in the field of furniture design.

Some wrong decisions and faulty practices applied during the repair and restoration of traditional buildings cause more damage to the structures due to the materials used in the repair. In this study, brick, mortar, plaster, and wood samples were taken from one registered building in the Konuralp neighborhood of Düzce Province, which has survived to the present day by preserving its original structural features and reflecting the characteristics of traditional housing. Texture, chemical and petrographic analyses were carried out on the samples. In line with these analyses, a scientific basis was created for selecting material properties in the repair and reuse processes of traditional buildings, and suggestions are made for the analysis of materials specific to traditional buildings in Konuralp.

Buildings can generate heats which are mostly generated from the machinery using inside the buildings, and these heats generally released to the atmosphere. Buildings can also block the wind flow by their canopies and trap the heat by using low albedo materials. These causes pointedly contribute to urban heat island and greenhouse effects. Likewise, urban development and building construction in Cambodia are growing rapidly. The construction has been recognized as a key development sector while thousands of buildings are being built and have been operated in the main cities. However, those buildings mostly have not been considered to incorporate sustainability concepts while the major final energy consumers in the country are buildings. The buildings’ energy consumption is also projected to increase more than double until 2040. Hence, sustainable building promotion in Cambodia is necessary, and sustainable building criteria are completely required. This research aims to find out significant sustainable building criteria for Cambodia and focused on planning and design criteria because having proper planning and design is a smart start leading to achieving building sustainability in all stages. This research used the Delphi methods to validate the relevant sustainable building criteria available in the literature and then select the significant ones for Cambodia based on the Delphi consensus. The results showed that ninety-nine consensus planning and design criteria were found to be significant for sustainable buildings in Cambodia.

Roof and roofings built to protect the housing and homeowner from undesirable rainwater, have been seen an important structural element throughout history in the entire of housing. In this research, structural and spatial relationships between building envelope with isolation from water in traditional housing architecture are analyzed. Roof, eaves and rain gutters which are isolation from water items were investigated according to shapes, slope direction, materials, carrier systems and covering materials. The qualification of the roofing, eave and rain gutter elements which are equipment elements related to the comfort of the building envelope and the extent of changes in these elements were examined at the traditional housing level. Exemplary, the traditional housing in the city of Trabzon in Turkey were selected. During the completion process of the working, detailed aims related to structure-health reinforcements were specified with the relevant literature review. The chart form has been developed for compilation of information about the general characteristics of the housing in the research area and the building-health reinforcements within the aim of the research. Exemplary houses were selected by external observation technique and the data obtained as a result of observations, interview and determinations related to general characteristics and building-health reinforcements of these housing were handled into a chart form. By evaluating the data obtained; harmony and contrasts in system level practices, the dimensional properties of the elements at the spatial level, the greatness and accuracy levels preferred in various fittings, the harmony and contrasts in the materials, dimensions and practices of the elements at the system and spatial level, harmony and contrasts of applications of new opportunities at the level of building-health reinforcements in traditional housing, conclusions were drawn to identify special and general situations at the level of building-health reinforcements and to obtain information about the comfort requirements of traditional housing. Nowadays, where the health of the building, which is mostly ignored, is gaining importance day by day, concrete and applicable solution data are presented and interpreted for new designs to be made in this direction.

Water scarcity, particularly in arid and semi-arid regions, poses a significant challenge to crop production, with drought being a prevalent factor limiting grain production globally. Enhancing agricultural water use efficiency is crucial for managing water resources effectively in these areas. Water resource management involves planning, developing, distributing, and optimizing the use of water resources. Water use efficiency management is also essential for crop growth in arid regions. Various agronomic and irrigation strategies can improve crop water use efficiency and drought tolerance. The primary goal of these strategies is to maximize irrigation efficiencies by applying the precise amount of water needed to restore soil moisture to the desired level. These sustainable practices not only reduce the cost of water and labor for farmers through reduced irrigation but also optimize the use of soil moisture storage. This review paper explores practical techniques to improve water use efficiency, highlighting the role of nutrients in enhancing water use efficiency in crop plants.

Studies have demonstrated the critical role that safety plays in preserving favourable working conditions in the construction industry, which is necessary to accomplish goals. The aim of this research was to inform stakeholders in the construction industry in developing nations about the value of safety and possible strategies for influencing their opinions regarding safety protocols. The importance of safety to the construction sector, which is crucial to the advancement of the country, has also been emphasized. However, due to a lack of adequate safety understanding among stakeholders in the construction sector, the construction industry is characterized by a great deal of instability and hazard. To determine what factors, affect productive working conditions in the construction production, this study examined safety. A conceptual framework for safe working conditions in the construction sector was developed by considering several aspects, including the person dimension, environment factor, safety behaviour, organization features, technology, and incentives. It is now imperative to bring in these dimensions to improve the safe working conditions in the construction industry, particularly in the developing countries. By putting these safety factors into practice, the construction industry can reduce safety risks, lower the number of accidents and fatalities, cut expenses related to subpar safety performance, safeguard the reputation of construction companies, boost employee morale and satisfaction with their work, enhanced employee retention, reduced absenteeism, and enhanced sustainability goals. Additionally, the proposed conceptual framework is assured to be new and to be widely accepted in the developing nations. Based on this assumption the conceptual framework is designed.

A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

Tropical regions face significant energy challenges due to climatic conditions. This study investigates the interplay between sustainable architecture and building energy regulations in mitigating these challenges. The study aims to assess the effectiveness of existing building energy regulations in promoting sustainable architecture in tropical climates and identify key architectural strategies and regulatory frameworks for optimizing energy efficiency in tropical buildings. A comparative analysis of building regulations and case studies of sustainable buildings in selected tropical regions is conducted. The findings reveal that current regulations often must be revised to address tropical climates' unique energy demands. Incorporating passive design principles, renewable energy systems, and material selection is crucial for energy efficiency. It is recommended that building energy regulations be strengthened to mandate sustainable design strategies and provide incentives to promote the adoption of energy-efficient technologies.

The purpose of this paper is to construct an evaluation system for AI painting software based on generative adversarial network technology, which optimizes the performance of the related software in terms of functionality, ease of use, system performance and safety. The results of the questionnaires are statistically analyzed. In addition, exploratory factor analysis was supported to extract the data of the study, which was ultimately used to calculate the weight and importance of each index through fuzzy hierarchical analysis method. The study constructed an evaluation system for AI painting software based on generative adversarial network technology, including 16 indicators of functionality, 16 indicators of ease of use, 7 indicators of system performance, and 8 indicators of safety respectively that their alpha coefficients were 0.882, 0.962, 0.932, 0.932, and 0.932, respectively. In addition, the accumulated explanatory variances of their coefficients were 84.405%, 84.897%, 84.013%, and 72.606%, respectively, 73.013%, and 72.606%, respectively. It is clear that the items included in each of the indicators are homogeneous, with a high degree of internal consistency. This paper suggests that the development of AI painting software focusing on functionality, ease of use, system performance and safety can enhance the market competitiveness of the software.

The emergence of prosumers, who actively participate in designing and producing goods, has generated interest in domestically manufactured products. Factors such as innovation, design methods, component reuse, prototyping, and digital fabrication empower prosumer designers to realize their ideas and enhance products to meet their specific design requirements. This article presents a case that combines bioinspired design methods with prosumer characteristics from the perspective of a designer who uses biological research results acting as a prosumer. By analyzing prosumer needs, bioinspired design, and domestic fabrication requirements, designers define the methods that best suit their possibilities. As a result of using biological information, the geometry of Samara seeds, propeller sizing, wind tunnel tests, and subsequent improvements, the custom design of a bioinspired microgenerator has been refined to the final design of a bicycle flashlight. The aim is to popularize a working approach that facilitates the interaction of design methods and reinforces domestic manufacturing processes. Implementing bioinspired design methods within the prosumer context offers a methodological alternative to transform the current economic model, promoting systemic sustainability and the development of proprietary technologies.

Climate change presents an urgent global challenge, manifesting in rising temperatures and extreme weather events with severe societal impacts. The Eastern Mediterranean, warming faster than the global average, faces immediate repercussions. Climate literacy emerges as pivotal, empowering individuals to comprehend climate science and act accordingly. This study delves into climate literacy, attitudes, and 'greening' behaviours in the Eastern Mediterranean hotspot of Greece, based on a survey of 1,962 citizens. Findings indicate high climate literacy but lower adoption of 'greening' behaviours, especially those involving financial costs. Regression analyses highlight the significant role of climate literacy, concerns about personal impacts, coping appraisal and trust in institutions in promoting 'greening' behaviours. The study underscores the need for multifaceted strategies emphasizing financial motivation, trust-building, and societal norm shifts. Socio-demographic disparities, including gender and occupation, highlight areas for targeted interventions. The emphasis on the mental health impacts of climate-related events underscores the need for holistic disaster management. Policy implications are discussed, highlighting the potential of expanded climate literacy to catalyze collective action toward sustainability.

Global warming and climate change have been the major concern for multiple disciplines. Population growth, urbanization, and industrialization are major contributing factors to such a problem by escalating the use of fossil fuels to meet their energy demands. The building sector has the largest share in using the total globally produced energy and emitting tons of greenhouse gas emissions. Emerging eco-friendly technologies such as solar and wind energy harvesting are being extensively explored but still, they are insufficient. Nature-inspired technologies can be the solution to our problem. For instance, algae are microorganisms that use water, light, and CO2 to produce energy and sustain life. Exploiting such characteristics in the built environment is termed algae building technology, a very efficient and green application for a sustainable future. Algae-integrated façades show great versatility through biomass and energy production, wastewater treatment, shading, and thermal and acoustic insulation. In this paper, algae will be introduced as a robust tool toward a greener and more sustainable future, The algae-building technology and its implementation will be demonstrated. Steps for applying this sustainable approach in Egypt will be discussed.

This work discusses seismic isolation technologies and analyses the concept of geotechnical seismic isolation (GSI) system, which is characterized by new principles of operation, using geomaterial with modified properties to reduce inertial seismic loads on buildings and structures. The aim of the study is to develop a geotechnical seismic isolation system in the form of vertical barriers, with different geometrical characteristics, using rubber-soil mixture (RSM). The novelty of the work consists in determination of effective constructive and technical solutions of vertical seismic barriers from RSM, which are characterized by reliability in providing seismic isolation of construction objects. Soil and superstructure interactions are modeled in Plaxis software, using the Northridge earthquake accelerogram. The results confirm the positive impact of using RSM as an effective material for GSI vertical barriers. The present numerical and experimental results show that the GSI system using RSM can significantly reduce the seismic hazard. The results of computational-experimental modeling will become a research, analytical and design basis for the development of new ways to ensure earthquake resistance of construction objects.

The application of AI technology in urban planning covers multiple levels, such as data analysis, decision support, and automated planning. Urban research relies on AI technology to understand and summarize the law of urban growth and improve the analysis of the evolution trend of urban space. Planning and design use AI technology to explore the relevant factors affecting urban development and their weights and discuss the critical role of green building technology in the sustainable development of the construction industry. With the increase in global energy consumption and carbon emissions, traditional building methods can no longer meet environmental protection requirements and efficient use of resources. As a sustainable development solution, green building technology has been paid more and more attention to and adopted by people. These technologies focus not only on the energy efficiency and environmental impact of buildings but also on the resource utilization and environmental load of green buildings over their entire life cycle driven by machine learning. This paper details the basic principles and applications of green building technologies, including AI-driven reduction of negative environmental impacts, improvement of occupant health, efficient use of resources, and optimization of indoor environmental quality. This paper focuses on the critical role of the LEED assessment system developed by the U.S. Green Building Council in advancing green building practices. In addition, the paper analyzes vital points such as water use in green building design, machine learning-driven wind environment optimization, solar technology application, and practical application cases of these technologies on a global scale.

In this systematic review, the PRISMA method was applied to examine publications from the last two decades that have investigated the noxious gaseous emissions from dairy barns. The aim was to analyse the outcomes from literature studies estimating the quantities of polluting gases produced in dairy barns, with specific focus on ammonia (NH₃) emissions. The review also explores proposed methods to reduce the associated effects through mitigation strategies. Estimation of NH₃ emissions is significantly influenced by the complex interactions among several factors, including animal management practices, such as controlling animal behavioral activities; manure management, like utilising practices for floor manure removal; the type of structure housing the animals, whether it is naturally or mechanically ventilated; and environmental conditions, such as the effects of temperature, wind speed, relative humidity, and ventilation rate on NH₃ release in the barn. These influential components have been considered by researchers, identifying targeted mitigation strategies. Despite growing attention to the issue, gaps in the scientific literature were identified and discussed, particularly regarding the analysis of mitigation strategies and their long-term impacts (i.e., environmental, economic and productivity-wise).

Search for the new non-invasive methods of investigating the functioning of human internal organs is an urgent task. One of these methods for assessing the functioning of the human res-piratory system is electromagnetic sensing, based on a significant difference in the dielectric permittivity of muscle tissue and air. During breathing, when the lungs are filled with air, the dielectric permittivity of the lungs decreases, which leads to a change in the level of the elec-tromagnetic signal passing through the body. Results of experiments on recording changes in the level of electromagnetic radiation passing through the human body, performed on an experimental device consisting of eight transmitting and receiving antennas located on opposite sides of the chest have been presented in the article. The possibility of visualizing the measured “pulmonograms” in the form of dynamic two-dimensional images showing the process of filling various parts of the lungs with air has been demonstrated.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

This paper describes the state of the art and future opportunities for process design and sustainable development. In the Introduction the main global megatrends and European Union's response to two of them, the European Green Deal, are presented. The organization of professionals in the field, their conferences and publications support the two topics. A brief analysis of the published documents in the two most popular databases shows that the environmental dimension predominates, followed by an economic one, while the social pillar of sustainable development is undervalued. The main design tools for sustainability are described. As an important practical case, the European chemical and process industries are analyzed and their achievements in sustainable development are highlighted; in particular, their strategies are presented in more detail. The conclusions cover the most urgent future development areas of the process industries, carbon capture with utilization or storage, process analysis, simulation, synthesis and optimization tools; zero waste, circular economy and resource efficiency already play an important role. However, more profound changes are needed in the coming decades, including a shift away from growth with changes in habits, lifestyles and business models. Lifelong education for sustainable development will play a very important role in the growth of democracy and happiness instead of consumerism and neoliberalism.

Driven by the growing interest of the scientific community and the proliferation of research in this field, cranial implants have seen significant advancements in recent years regarding design techniques, structural optimisation, appropriate material selection and fixation system method. Custom implants not only enhance aesthetics and functionality but are also crucial for achieving proper biological integration and optimal blood irrigation, critical aspects in bone regeneration and tissue health. This research aims to optimize the properties of implants designed from triply periodic minimal surface structures. The gyroid architecture is employed for its balance between mechanical and biological properties. Experimental samples were designed varying three parameters of the surface model: cell size, isovalue and shape factor. Computational simulation tools were used for determining the relationship between those parameters and the response variables: the surface area, permeability, porosity and Young modulus. These tools include computer aided design, finite element method and computational fluid dynamics. With the simulated values, the corresponding regression models were fitted. Using the NSGA-II, a multi-objective optimisation was carried out, finding the Pareto set which includes surface area and permeability as targets, and fulfil the constraints related with the porosity and Young modulus. From these non-dominated solutions, the most convenient for a given application was chosen, and an optimal implant was designed, from a patient computed tomography scan. An implant prototype was additively manufactured for validating the proposed approach.

In the last decades, the impacts of urbanization on the hydrological cycle have led to an increase in the frequency and magnitude of urban flooding events, also amplified by the effects of climate change. Sustainable Drainage Systems (SuDS) provide a revolutionary change in this field, improving the sustainability and resilience of cities. This research explores the integration of different SuDS with the aim of significantly reducing both flow volume and celerity of floods in a residual urban catchment area of metropolitan city of Querétaro (Mèxico), where extreme rainfall frequently occurs. This catchment is a representative suburb of urban pressure and environmental degradation problems. Currently, managing storm water under climate uncertainty through a multi-disciplinary approach is a major concern in this urban area. A 1D-2D coupling model of shallow water equations, finite volume method, unstructured meshing method, and hybrid parallel computing application defined the optimal configuration of SuDS at catchment scale to reduce the flood vulnerability in Querétaro. Specifically, in this paper we explore the management issues of the proposed SuDS configuration that acts as a water resource system with multiple purposes. A generic simulation model called MODSIM was applied to simulate the designed urban drainage system under a balanced IPCC future climate scenario in terms of reliability, resilience and vulnerability against water scarcity.

The risk classification of barrier lake is the key to conducting emergency treatment in a scientific manner. Such difficulties are faced as short time for risk evaluation, complex evaluation indicators, difficulty in obtaining information quickly and quantifying index weights. Based on this, this paper constructs a quantitative risk classification model for barrier lakes based on D-AHP. On the basis of studies on nearly 100 cases of barrier lakes, an 8-factor evaluation index system and quantitative classification are proposed. The methods of rapid calculation of reservoir capacity curve of barrier lake and intelligent identification of particles on the surface of barrier body were developed, which realized the rapid acquisition of 8-factor evaluation index information in emergency environment. The D-AHP method dealt with inconsistent weight assignment to evaluation factors by experts, which helped achieve weight quantification of 8 factors. The risk assessment on15 barrier lakes such as Tangjiashan barrier lake show that the conclusion drawn with risk classification method proposed in this paper is basically consistent with that of the traditional table-lookup method. However, the table-lookup method ignores cumulative loss’s impacts on the risk level of barrier lakes, and considers the extremely severe loss of barrier lakes as a sufficient condition for the evaluation level to be grade I, and thus a deviation in the evaluation. The risk classification method proposed in this paper is more reasonable and reliable.

Aloe vera is well known for its biological properties as a bioflavonoid-anti-inflammatory, antibacterial agent. It has been used frequently in the food sector as food coating for its hygroscopic properties and as an ingredient in the lucrative industry. Studies have also included Aloe vera as an eco-friendly green solution based on these properties. The current research focuses on the use of Aloe vera gel in printing pastes as an alternative sustainable solution to synthetic thickeners, evaluating its wet performance and ease of fabric stitching, and has been inspired by studies that similarly used this substance measuring its effect on the fabric's coefficient of friction and antimicrobial action. In the current study, printing pastes with natural colourants and Aloe vera gel thickener derived from natural leaves from Crete increased the fabric's mechanical resistance to abrasion compared to the untreated pastes. The measured performance did not differ substantially from prints with traditional synthetic pastes, hence tolerating the substitution with the non-contaminant variant. The enhanced resistance to abrasion and wear prolongates the fabric's serviceable life and resulting garments, decreasing the need for high industry processing volumes and, as a result, reducing pollution. The resistance to wear was evaluated using the dominant method in textile testing of the Martindale apparatus, which measured the cycles to failure, weight loss, and general appearance deterioration using the official photographic standards.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

Novolac phenol-formaldehyde resins have gained extensive commercial utilization across diverse applications due to their exceptional mechanical, thermal, and chemical resistance properties. In this investigation, we successfully synthesized a traditional novolac, and a biobased novolac phenol-formaldehyde resin by partially substituting phenol with a bio-oil obtained from the organic phase resulting from the fast pyrolysis of pinewood biomass. Despite extensive investigations into the curing behavior of novolac resins crosslinked with hexamethylenetetramine (HMTA) through numerous model-fitting cure kinetic studies, a comprehensive model for predicting the crosslinking of bio-based phenol-formaldehyde resins in the presence of HMTA has not yet been studied. The primary objective of this research was to compare and apply several commonly used kinetic models to predict the degree of curing and cure rate of the synthesized resins, using DSC dynamic measurements. Our results demonstrated that the autocatalytic model exhibited excellent fitting for the traditional novolac resin and HMTA mixture, while the Kamal model showed better fitting with the experimental data obtained for the bio-based phenol-formaldehyde resin and HMTA system. In addition, the results evidenced a significant drop in the curing temperature by partially replacing phenol with bio-oil. Additionally, the results revealed a notable reduction in curing temperature when phenol was partially substituted with bio-oil. This substitution not only offers environmental benefits but also promotes energy efficiency and enhances production safety. The data collected in this study is pivotal for our subsequent research endeavors, which aim to develop environmentally sustainable materials optimized for use in 3D printing manufacturing processes.

Tremor is a prevalent neurological disorder characterized by involuntary shaking or trembling of body parts. This condition impairs fine motor skills and hand coordination to varying degrees and can even affect overall body mobility. As a result, tremors severely disrupt the daily lives and work of those affected, significantly limiting their physical activity space. This study developed an innovative Spatial Augmented Reality (SAR) system aimed at assisting individuals with tremor disorders to overcome their physical limitations and expand their range of activities. The system integrates eye-tracking and Internet of Things (IoT) technologies, enabling users to smoothly control objects in the real world through eye movements. It employs a virtual stabilization algorithm for stable interaction with objects in the real environment. The study comprehensively evaluated the system's performance through three experiments: 1) assessing the effectiveness of the virtual stabilization algorithm in enhancing the system's ability to assist individuals with tremors in stable and efficient interaction with remote objects; 2) evaluating the system's fluidity and stability in performing complex interactive tasks; 3) investigating the precision and efficiency of the system in remote interactions within complex physical environments. The results demonstrate that the system significantly improves the stability and efficiency of interactions between individuals with tremor and remote objects, reduces operational errors, and enhances the accuracy and communication efficiency of interactions.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

The awareness of the vulnerability of existing structures under both seismic and energy viewpoints highlight the need to develop integrated retrofit solutions combining the structural and thermal performances. In this perspective, the study explores the efficacy of the Resisto 5.9 Tube system, a seismic coat that improves the seismic behaviour of masonry and reinforced concrete (RC) structures, also enhancing their energy performances, thanks to the thermal coat integrated in the basic steel system. The research involves the application of a design procedure specifically developed for this retrofit system from the seismic perspective. Once all the system elements are designed, non-linear static analyses are performed with a Finite Element software comparing the building’s seismic performances before and after the application of Resisto 5.9 Tube. The results demonstrate a significant increase in seismic safety coefficient, proving that this intervention type can be useful to obtain the seismic upgrading of existing RC buildings.

This paper presents a methodology based on deep learning models and metaheuristic algorithms for the optimization of airfoils for the design of aircraft wings with large endurance. The use of AZTLI-NN (a neural network with an architecture composed of a multilayer perceptron and a variational autoencoder) is implemented for the prediction of graphs of the aerodynamic coefficients of the airfoil as a function of the angle of attack. This neural network presents good predictions of the aerodynamic coefficients, similar to the coefficients obtained with computational fluid dynamics simulations. AZTLI-NN in combination of metaheuristic algorithms and the CST profile parameterization method show excellent performance in single-objective and multi-objective profile optimization tasks.

Indoor environmental comfort is fundamental to human health as people spend 90% of their time indoors. This aspect is even more crucial in hospitals, where the concept of health is closely linked to well-being, ethics, and environmental aspects. Emerging methodologies and technologies such as Digital Twin, Building Information Modeling, the Internet of Things, sensing technologies, and data analytics offer new opportunities to ensure healthier environments and more efficient building management. This paper provides an assessment of how digitalization can support decision-making processes related to maintaining high levels of indoor environmental comfort in hospital settings, particularly by analyzing how real-time data processing and the application of machine learning can promote proactive interventions in these facilities. The methodological approach was based on four phases: defining the objectives of the digital twin, identifying the input data to build and feed the digital model, defining the KPIs to evaluate the system's correct functioning, and identifying the enabling technologies to be integrated into the system to achieve the set goal. The result is a digital twin for managing the operating room and its related services, with the aim of guiding decisions based on accurate data and improving operational efficiency, levels of environmental comfort, and safety regarding the diffusion of medical gases.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

Mobile inspections conducted by intelligent tunnel robots are instrumental in broadening the inspection reach, economizing on inspection expenditures, and augmenting the operational efficiency of inspections. Despite differences from fixed surveillance, mobile-captured traffic videos have complex backgrounds and device conditions that interfere with accurate traffic event identification, warranting more research. This paper proposes an improved algorithm based on YOLOv9 and DeepSORT for intelligent event detection in edge computing mobile device using the intelligent tunnel robot. The enhancements comprise the integration of the Temporal Shift Module to boost temporal feature recognition and the establishment of logical rules for identifying diverse traffic incidents in mobile video imagery. Experimental results show that our fused algorithm achieves a 93.25% accuracy rate, an inprovement of 1.75% over the baseline. The algorithm is also applicable to inspection vehicles, drones, and autonomous vehicles, effectively enhancing the detection of traffic events and improving traffic safety.

The development of ballistic protection vests (BPVs) has become increasingly significant, particularly in the design of soft panels, which are critical to the overall size and configuration of these vests. Despite their importance, a standardized design process for soft panels is lacking in the literature. This research addresses this gap by creating soft panels tailored to the body types of regional soldiers while adhering to relevant standards. We propose a comprehensive design algorithm and evaluate the applicability of the National Institute of Justice (NIJ) standard 0101.06 test templates for configuring these panels. This study aims to design soft ballistic panels for BPVs that cater to the body type requirements of regional soldiers and comply with NIJ 0101.06 standards. We have developed an algorithm for designing soft panels and analyzed the feasibility of using NIJ test templates for their configuration. The research encompasses a detailed literature review, analysis of existing BPV soft panels, and comparison with NIJ test templates. The panels were designed and scaled using computer-aided design (CAD) systems and evaluated through by physical fitting on mannequins and virtual fitting using the Clo3D program. Our findings indicate that the NIJ standard test templates are only partially applicable to the design of soft panels. The developed methodology includes an algorithm and size specifications tailored to regional covers. A coefficient (K) was identified to calculate the soft panel surface area prior to design, thereby saving time and resources.

The integration of digital technologies in managing technical and design information is trans-forming the fields of architecture and construction. This article presents a website developed to compile detailed information on the construction processes of buildings at Pontificia Universidad Javeriana (PUJ) campus. The site offers comprehensive construction records and interviews with designers, engineers and other professionals who collaborated to align design approaches with technical construction requirements. A chronological record of the construction processes was maintained, from inception to completion of the buildings. Digital tools include interactive modules that facilitate access and data updates, improving coordination and efficiency for man-aging future projects. Gamification elements and social media dissemination boost user engage-ment. The study also assesses the impact of the website on the university community, analyzing usability and user (N=235), among students, teachers, and staff members. Findings indicate that digital technologies optimize construction processes and improve the management of technical and design information, and reveal opportunities for future projects and research, benefiting both internal and external stakeholders.

Nowadays, microfluidics has become an anarchist interdisciplinary topic with considerable attention in a wide range of biotechnology applications. In this research work, numerical investigation of microfluidic micro-mixer is carried out using hybrid actuation approach with different micropillar shapes and gaps. For this purpose, COMSOL Multiphysics is used with three different physics such as thermoviscous acoustic to solve acoustic governing equations, laminar physics is used to solve fluid flow governing equations and diluted transport species is used to solve mixing governing equations. The simulations were carried out with flow velocity of 200 µm/s at both inlets with an oscillation frequency of 15kHz. The outcomes were in the form of acoustic characteristics such as acoustic pressure, acoustic velocity, acoustic streaming and mixing index. The results revealed that the inclusion of micropillars enhanced the mixing performance and strength of acoustic field resulting in improvement of mixing performance compared to the case without micropillars. In addition, it was also investigated that blade shape micropillars with 0.150 mm gaps deliver best results compared to the other cases with maximum and minimum values of the mixing index 0.95 and 0.72 respectively. The obtained results can be extremely helpful for design and modifications of hybrid microfluidics micro-mixer.

This research aims to review the educational and research operations of Mahasarakham University and propose development directions for the university to meet sustainable development criteria for ranking as a green university. This involves gathering data and analyzing the results of operations over the past 3 years, then using this analysis to synthesize lessons learned and develop guidelines for sustainable development in the coming years. The study found that the university's policies and strategies implemented following the annual performance evaluation criteria align with the green university assessment criteria for education and research. This has resulted in minor improvements in curriculum for sustainability. However, community service projects for sustainability have increased by 89.10%, while funding for sustainable research and academic publications related to sustainability has decreased. In summary, the projects under the university's development strategy adequately support and drive suitable development activities. Nevertheless, the university must continuously review its operations to adapt to changing contexts, budget constraints, and evolving competition and develop each year sustainably.

The construction sector is a paradigm shift into the sustainable era to solve environmental issues, combat global warming. And the reflection of this is on Green Buildings where energy savings, cost savings, occupant comfort takes priority. The idea of green building efficiency merges sophisticated technologies, creative architectural design templates, and reusable materials into the whole life cycle of a building process in order to render minimum environmental impact. The pilot project of The National Institute of Geophysics and Volcanology (INGV) - Irpinia headquarters, illustrates in this context, innovative technologies of energy transition with a photovoltaic parking with geothermal piles. The project is consistent with the concepts of Nearly Zero Energy Buildings (NZEBs), directed to a high energy performance and very low environmental impact. Incorporating geothermal piles is a major area of advancement in sustainable building ideas that use the Earth's natural heat to create an energy efficient solution in heating and cooling. Project Goals – The project aims to install emission free renewable cleaning energy cost-effective clean production and increase energy efficiency, reduce CO2 emissions and energy security. For this purpose this paper, using as a support the PVGis software, evaluates the potential produced with the photovoltaic system installed in the canopies. With the help of this analysis, it is feasible to determine the amount of electricity produced as well as the system's amortization based on the excess energy sent to the public grid. The project is regarded as creative from the standpoints of energy given the use of geothermal and photovoltaic systems, as well as from an architectural and design perspective due to the use of novel materials. This all-encompassing strategy establishes INGV as a pioneer in the promotion of environmentally friendly technologies and shows a dedication to sustainability and energy efficiency.

This paper proposes an innovative approach to address the challenge of softening deformation of thermal-curable thermosets during additive manufacturing. This approach involves the development of a composite powder composed of thermosetting materials with distinct curing temperatures, the utilization of Cold Spray Additive Manufacturing (CSAM) technology for 3D printing, and the application of a stepwise isothermal curing process. The corresponding effectiveness is validated by case studies. The results demonstrate that samples printed via CSAM maintain a solid state without deformation. During the post-curing process, each component of the composite material cures independently while the other components remain in a solid state, providing structural support for the whole material, thereby effectively reducing the softening deformation during the post-curing process. This approach offers a novel perspective for the additive manufacturing of thermal-curable thermosets.

As the carbon storage capacity of timber is recognized, there is growing interest in timber and wooden structures as a solution to various environmental problems. The use of Korean timber with substantial carbon storage capacity is required to reduce Korean carbon emissions and circulate timber resources. In this study, fire tests were conducted to investigate the charring properties of glued laminated timber columns made of Korean larch. The fire tests were conducted under both load-bearing and non-load-bearing conditions. The fire test results showed that the charring depth was affected by the corners of the section, and that the load ratio had an insignificant influence on the charring depth when the load ratio was 0.9 or less. This study provides data that can be used to compare the charring properties of laminated wood produced using South Korean larch with the charring properties of foreign standards. This provides reference data for developing fire-resistant design standards for timber structures made from South Korean timber.

The decarbonization of the electricity grid as one among the actions to reduce fossil fuel emissions, and thus their impact on global warming in the future, will be achieved mainly via the integration and widespread diffusion of renewable power sources. This is going to be supported also by the shift from the paradigm production-transmission-distribution, where electricity production oversees large-size power plants, to renewable-based distributed/diffused production, where electricity is generated very close or even by the same (group of) user(s) (or prosumers in the latter case). The number of mid-/small-size installations based on renewable energy technologies will therefore increase substantially, and the related renewable generation will be dominant against that from large-size power plants. Unfortunately, this will reduce the reliability of the grid very likely, unless appropriate countermeasures are taken/implemented, hopefully at the same time the paradigm shift is being achieved. To this aim, it is important to identify the anomalies and main fault causes that might determine in renewable-based power systems. This paper surveys the current state-of-the-art on anomalies and faults affecting wind-PV-storage hybrid power systems, i.e., the main renewable technology ensemble that will establish the future grid, and highlights possible research directions that may help to fill the literature gaps.

Energy harvesting is an emerging topic recently. This harvested energy is used to operate wireless sensors for different industrial monitoring and automation. To maximize the harvested energy in spinning systems, the harvester should vibrate at resonance for different spinning frequencies which can be achieved by active fitting. In this research, a novel methodology was developed by actively customizing the length of vibrating element beam to manipulate its natural frequency according to the spinning frequency. Different models were investigated numerically and experimentally to verify the proposed methodology. COMSOL Multiphysics software V5.1 was used to develop the numerical model, then and tip deformation and voltage difference results were benchmarked. The numerical model was verified experimentally by attaching a piezoelectric MIDE PPA 1021 which its vibrating length was varied by changing the supporting length from 0 mm to 12 mm to a spinning object having variable frequency from 0-200 Hz. It is found that the MIDE PPA 1021 beam vibrated at its resonance throughout the specified spinning frequencies. The proposed harvester can be applied in battery-free sensors being used in automotives, wind-mills blades, and rotating machinery.

Confronting the dual challenges of rapid urbanization and climate change, although extensive research has investigated the influencing factors and practical strategies of urban carbon emissions and urban vibrancy, respectively, the unclear mutual nexus between them and the development strategy of collaborative optimization requires further in-depth analysis. This study explores the delicate balance between urban vibrancy and low-carbon sustainability within the confines of Beijing’s Fifth Ring Road. By integrating OpenStreetMap, land use, population, and building carbon emission data, we have developed a reproducible method to estimate total carbon emission and emission intensity per capita. Furthermore, we have introduced vibrancy index data to distinguish the vibrancy evaluation of residential and non-residential land and applied cross-combinational classification technology to dissect the spatial correlation between urban carbon emissions and urban vibrancy. The results reveal that the four combination typologies show more significant differences and regularity in residential land. Based on the discovery of spatial correlation, this study puts forward corresponding development strategy suggestions for each typology based on geographical location and the requirements of urban development policies of these four combination typologies. In conclusion, our study highlights the importance of integrating carbon emissions and urban vibrancy comprehensively in sustainable urban planning and proposes that various land use combinations need targeted development strategies to achieve this goal, which need to consider population, energy, service facilities, and other diverse aspects.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

The effects of climate change health impacts on urban health care systems and vulnerable populations are a researched topic with foundations on urban risk management, urban health methodologies, and sustainable urbanization. As climate change is a dynamic and transformative global issue the gap between adaptation and mitigation efforts and urban planning relies, among other things, in the limitations of previous studies of risk management structures tailored to the existing strategy to calculate the uncertainties and predict their influence on urban systems and subsystems. Moreover, as climate and health is a well-researched issue, it is also complex as the methodologies and strategic approach to minimize health risks of climate change is intrinsically contingent to risk methodologies and policy-making processes that are efficient with support of knowledge-based information. This paper emphasis the need for focusing on urban health risk management methods that serves to identify potential opportunities, and then manage and take action to prevent adverse health effects. It also emphasizes the probability of events and their consequences, which are measurable both qualitatively and quantitatively.

CAMx-LPiG (Comprehensive Air Quality Model with Extensions – Linear Plume in Grid) is an online hybrid model, based on the Chemistry and Transport Model (CTM) CAMx, that includes a sub-grid scale module to simulate the dispersion of linear road traffic emissions, called LPiG. LPiG is a plume in grid module specifically developed by extending the capabilities of the Lagrangian puff sub-grid model available in CAMx. The online integration of the local scale model within the Eulerian CTM allows for a multiscale simulation of air quality from the regional scale to the urban scale, preserving a coherent description of the chemical state of the atmosphere at all spatial scales and avoiding any double counting of the emissions simulated by the sub-grid module. In this work the model is presented and evaluated against measured NO2 concentrations for the city of Milan for the month of January 2017. The model is able to introduce road traffic induced gradient in NO2 concentration at sub-grid resolution. Moreover, CAMx-LPiG is shown to reduce the bias compared to CAMx stand-alone simulations.

The assessment of existing bridges constitutes a serious challenge for the researchers since their safety evaluation is a complex task due to several sources of uncertainty affecting the parameters identified in the knowledge process. In particular, a high level of uncertainties may arise in the case of prestressing systems requiring special investigation strategies and experimental technologies. The paper aims to investigate how the knowledge uncertainties influence the safety assessment of existing post-tensioned bridges. The semi-probabilistic approach is used, and uncertainties related to the knowledge process are described considering the number of tests, the confidence level assumed for the estimation of the problem parameters, and the measurement errors of in-situ tests. Results concerning a typical post-tensioned bridge are reported and the variability of the outcomes is discussed and compared with a reference case of “perfect knowledge”. The main results of the study confirm the general robustness of the semi-probabilistic Eurocodes safety format and provide an overview of dispersion due to different choices about the number of tests and confidence level. The measurement errors may lead to significant under-estimation of the computed structural capacity with respect to the reference one.

Our study reviews the significance of archaeological parks in the tourism sector, with a specific focus on how digital presence and visitor feedback impact their cultural and touristic appeal. Utilizing statistical analyses such as regression and cluster analysis on data sourced from both Hungarian and Western European parks, the research scrutinizes TripAdvisor and Google ratings, alongside the volume of photographs and reviews. The findings highlight a modest correlation between digital visibility and overall visitor ratings, underscoring the complex relationship between online engagement and the quality of visitor experience. Notably, the cluster analysis identified two distinct groups, signifying diverse levels of visitor engagement and digital visibility across the parks. The conclusions drawn advocate for a comprehensive strategy to enhance visitor experiences, emphasizing the integration of digital engagement with the promotion of the parks cultural and historical values. By exploring the influence of digital presence on the appeal of archaeological parks, our study sheds light on the evolving interface between urban studies and digital heritage, highlighting how digital tools and online platforms are becoming increasingly integral in shaping the perceptions and experiences of urban cultural sites.

Childhood nutrition is a cornerstone of long-term health, yet many children exhibit reluctance to consume healthy foods such as vegetables. This aversion can be influenced by various factors, including food neophobia and the sensory and visual appeal of the foods presented. Understanding how visual cues affect children's willingness behaviors can provide insights into effective strategies to enhance their dietary habits. This study aims to investigate the liking and emotional responses on the relationships between intrinsic and extrinsic cues and children's willingness to eat and to ask parents to buy. To understand how these factors influence children with food neophobia food-related behaviors and to identify effective strategies to promote healthier eating habits. A sample size consisting of 420 children recruited was needed in this cross-sectional study. A validated and reliable self-administered questionnaire was employed. Independent t-test and ANOVA were used to test the differences between gender and food neophobia means. Spearman correlations were used for correlation analysis. Hierarchical regression analyses were conducted to explore the relationships among intrinsic cues, extrinsic cues, and the mediating effect of liking and emotional responses. Attributes such as plate color and shape significantly influence children's food-related behaviors and their emotions. Liking and emotional responses significantly mediates the relationship between intrinsic/extrinsic cues and willingness. Positive visual cues experiences are crucial for increasing children's inclination to purchase and consume. Positive emotional responses enhance acceptance and purchase. There are significant differences between boys and girls. Boys prefer blue and triangular plates, while girls prefer pink plates and generate more positive emotions. Children with food neophobia will initially experience a disorder, but its negative effects can be mitigated by increasing sensory appeal and emotional engagement. By employing strategies designed to enhance visual cues and liking and emotions, children’s willingness to choose healthy eating habits can be effectively increased.

The complexity of the design in high-rise residential projects is a challenge for the construction industry in completing projects that fit the needs of users. Performance-Based Building Design (PBBD) appears as a design concept that can describe these needs into performance requirements. In this case designing a building can be considered as an iterative process of exploration, where desired functional properties can be created, the shapes are suggested, and evaluation processes is used, so as to bring together the shapes and functions of the building. This concept is a container for designers to produce high-performance buildings. This study aimed to identify the performance-based building design factors applied by architect designers and engineers in high-rise residential building in Surabaya. As part of this study, primary data was collected based on surveys conducted through observation and questionnaire distributed to designers who had or were involved in the high-rise residential design process in Surabaya. A total of sixty-eight respondents were included in this study. Descriptive analysis through a mean and standard deviation scatter plot was used to rank the application of PBBD. Meanwhile, factor analysis was used in the analysis of PBBD application factors. From the results of the analysis, four factors were obtained for the application of PBBD in high-rise residential buildings in Surabaya, namely; the interests of occupants, the sustainability of building operations, the design collaboration process, and the risk of loss. Future research is the influence relationships and measure the success model of PBBD at a higher level into BIM (Building Information Modeling) interoperability.

Long term Precipitation and temperature variations are one of the main determinants of climate variability of one’s area. The aim of this study is to determine trends variation in climatic elements of temperature and precipitation in the southern zone of Tigray regional state, Ethiopia. The station is assumed for the study of climatic records over southern zone of the region in detection for probable trends. The daily, monthly and annual precipitation totals and temperature observed at korem meteorological station were used for the period of 1981-2010 for Precipitation and 1985 – 2010 for minimum and maximum temperature. Summary of descriptive statistics and Mann Kendall test methods were employed for the observed data analysis to demonstrate any existence of possible trends. The main findings of the study indicated that the mean and maximum temperature had a general increasing trend; however, minimum temperature showed decreasing trend. In general annual temperature from 1985 – 2010 of the area showed a warming trend. Moreover analysis of the 30 years (1981-2010) annual precipitation showed a coefficient of variation ranging from 33.77 – 233 %. It indicated that the precipitation dissemination is not normal with large year to year variances.

We have studied the inheritance of mitochondria in Pelargonium section Ciconium using interspecific crosses. We generated 36 different interspecific crosses. We designed KAPS markers targeting four individual mitochondrial markers, belonging to the four main crossing parents, that discriminate between an individual species and the other section Ciconium species. We found that maternal inheritance of mitochondria is most frequent, but we find occasional occurrences of paternal inheritance, while biparental inheritance is rare. For the P. multibracteatum crossing series we found ambiguous results. Our results confirm what was found before, namely that paternal inheritance of mitochondria can occur in P. sect Ciconium but that the instance is rare and much less common than is the case for chloroplasts.

Autonomous navigation in dynamic environments poses a significant challenge in the field of ro-botics with the primary goals of ensuring both smooth and safe movement. This study introduces control strategy based on an Adaptive Neuro-Fuzzy Inference System (ANFIS) to enhance au-tonomous robot navigation in dynamic environments, emphasizing on collision-free path plan-ning. This strategy employs, a path planning technique to develop a trajectory that allows the ro-bot to navigate smoothly while avoiding collisions with both static and dynamic obstacles. The developed control system incorporates four ANFIS controllers: two are tasked with guiding the robot toward its end point, and the other two are activated for obstacle avoidance. The experi-mental setup conducted in CoppeliaSim involves a mobile robot equipped with ultrasonic sensors navigating in an environment with static and dynamic obstacles. Simulation experiments are conducted to demonstrate the model's capability in ensuring collision-free navigation, employing a path planning algorithm to ascertain the shortest route to the target destination. The simulation results highlight the superiority of the ANFIS-based approach over conventional methods, partic-ularly in terms of computational efficiency and navigational smoothness.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Developing and utilising of underground space is an vital direction for urban growth. Underground commercial streets, as a significant component of underground space accommodating extensive human social activities, and consequently necessitate the creation of human-scale spaces. In the evolution of urban design development towards greater refinement, applying architectural theories and excessively subjective designs has resulted in a deficiency of human-centered design and a disordered spatial environment. This study merges environmental psychology and architectural theory to determine the appropriate length of spatial scale. Two experiments focusing on spatial perception evaluation were conducted using a virtual experimental platform that featured varying dimensions of spatial scale combinations. These quantified combinations were correlated with perception evaluation, and regression analysis was employed to identify appropriate scale ranges, which were superimposed on the range of length selection. Finally, the optimal length and scale combination for underground commercial street spaces were established, providing a reference for the human-centered design of these environments.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

In this study, an attempt was made to investigate the Kenya case of multivariate causality of carbon dioxide emissions by employing a time series data spanning from 1961-2011 using the ARDL method of cointegration analysis. The long-run elasticities show that, a 1% increase in financial development increases carbon dioxide emissions by 0.28%, a 1% increase in GDP per capita increases carbon dioxide emissions by 1.32% and a 1% increase in urbanization decreases carbon dioxide emissions by 1.14%. There was a unidirectional causality running from financial development, food production index, GDP per capita, industrialization and urbanization to carbon dioxide emissions. The innovation accounting shows that 20% of future shocks in carbon dioxide emissions are due to fluctuations in financial development, 9% of future shocks in financial development are due to fluctuations urbanization and 22% of future shocks in food production index are due to fluctuations in carbon dioxide emissions.

One of the primary causes of the mechanical seal failure is rotor vibration. Traditional dynamic seal models often would not be able to fully explaining the failure mechanisms. The seal dynamic models proposed in this paper, including those developed by the authors, prove valuable in predicting seal dynamics during operation in specific turbomachinery and in explaining the causes of seal failure. The single-mass dynamic model is suitable for analyzing contact mechanical seal and simple design dry gas seals dynamics. The two-mass dynamic model is used for investigating operational dynamics processes in classical dry gas seals under complex loading conditions. The three-mass dynamic model is used to study various complex mechanical seal types. This model is able to determine the normal operating condition range and to explain leakage mechanisms in the presence of excessive rotor vibrations.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

This study introduces numerical advancements in an alternative design for the SPS Beam Dump Facility (BDF) at CERN. The design envisions a high-power operation target made of flowing liquid lead. The BDF is a proposed versatile facility at CERN, intended for both beam-dump-like and fixed-target experiments. The target behavior is assessed, assuming a proton beam with a momentum of 400 GeV/c, a pulse frequency of 1/7.2 Hz, and an average beam power of 355 kW. An evaluation is conducted using various Computational Fluid Dynamics (CFD) codes to analyze the behavior of liquid lead and to predict the thermal stress on the target vessel induced by the pulsed heat source generated by the charged particle beam. The comparison increases the reliability of the results, investigating the dependencies on the CFD modeling approach. The beam is modeled as a volumetric heat source with data coming from beam-lead interaction simulations provided by CERN and obtained with the Monte-Carlo code FLUKA. The velocity field and stress profiles are utilized to enhance the design of the lead loop and verify its viability and safety when operated with a liquid metal target.

In the provinces of the region, empirical constructions reached maximum points with these practices. The effects and pathologies appear as physical, chemical and mechanical failures in pillars, walls and roofs, generating uncertainty for the user. The current powerful design can detect the interior deterioration of coatings in adobe, brick and concrete constructions, and prevent collapses, material and economic losses. Experimental methods performed affirm the serious validity. The accuracy of the simulation and design provide a pre-test reliability of 95%. Five piles constructed of various materials participate in the prototype performance test, there is a correlation (R=0.9997) between the magnetic field range "B" (cm) and density "ρ" (g/cm³), also by increasing the current (i) in transit Q1 and coil L1, the induction of the "B" increases proportionally until penetrating the density of the wall of the building, having 5% reading error.

Sustainable and Responsible Design (SRD) harnesses design’s potential to address eco-social problems and in doing so challenge the status quo of design education by reframing the social and ecological consequences, boundaries and agencies of design. This critical and transdisciplinary approach frays the edges of traditional design disciplines with embedded and reflexive modes of learning. We describe characteristics of SRD education and present theories of learning to empower students in this complex terrain. The learning associated with SRD education is ecologically engaged, participative, critical, expansive and designerly. We recount case studies of our own experiences advancing sustainable and responsible undergraduate design education in the UK. We identify path constraints such as disciplinary fragility, appropriation, and power dynamics in the design school. The push for a revision of priorities generates tensions where there is often greenwashing rhetoric of sustainability and inclusivity. We describe strategies and tactics to address these tensions. We highlight the agency we have as educators and designers and argue that design education can only meaningfully participate in response to the challenges presented by climate change, other types of ecocide, and social problems when educators make substantive commitments to supporting sustainability literacies and design approaches that serve the interests of diverse stakeholders.

Clathrate hydrate-based technologies have been considered as promising and sustainable alternatives for the effective management of the climate change risks related to emissions of carbon dioxide, produced by human activities. This work presents a combined experimental and computational investigation of the effects of the operational procedures and characteristics of the experimental configuration, on the phase diagrams of CO2-H2O systems and CO2 hydrates formation, growth and dissociation conditions. The operational modes involved (i) the incremental (step-wise) temperature cycling and (ii) the continuous temperature cycling processes, in the framework of an isochoric pressure search method. Also, two different high pressure PVT configurations were used, of which one encompassed a stirred tank reactor and the other incorporated an autoclave of constant volume with magnetic agitation. The experimental results implied a dependence of the subcooling, (P, T) conditions for hydrate formation and dissociation and thermal stability of the hydrate phase on the applied temperature cycling mode, and the technical features of the utilized PVT configuration. The experimental findings were complemented by a thermodynamic simulation model and other calculation approaches, with the aim to resolve the phase diagrams including the CO2 dissolution over the entire range of the applied (P, T) conditions.

Isolation of new plant-derived lactic acid bacteria (LAB) is highly prioritized in developing novel starter cultures for plant-based fermentation. This study explores the diversity of LAB in Danish flowers and their potential use for plant-based food fermentation. 46 flower samples under 34 genera were collected for LAB isolation. By introducing an enrichment step, in total of 61 LAB strains were isolated and identified by using MALDI-TOF and 16S rRNA sequencing. These strains represent 24 species across 9 genera, predominantly Leuconostoc mesenteroides, Fructobacillus fructosus, Apilactobacillus ozensis, and Apilactobacillus kunkeei. Phenotypic screening for exo-cellular polysaccharide production revealed that 40 strains exhibited sliminess or ropiness on sucrose containing agar plate. HPLC analysis confirmed that all isolates produced exo-cellular polysaccharides containing glucose, fructose or galactose as sugar monomer. Therefore, the strains were glucan, fructan and galactan producers. The suitability of these strains for plant-based fermentations was characterized by using almond, oat and soy milk. The results showed successful acidification in all three types of plant-based matrices but only observed texture development in soy by Leuconostoc, Weissella, Lactococcus, Apilactobacillus, and Fructobacillus. The findings highlight the potential of flower-derived LAB strains for texture development in soy-based dairy alternatives.

The objective of this study is to determine the relationship between body condition score (BCS) and body carcass fat (BCF) of ewes at two key stages of the production cycle. Data were collected from 88 Coopworth ewes including BCS measurements manually evaluated by the farm manager, BCF measurements determined by computerized tomography (CT) and body parameter measurements automatically determined by an image processing application. Artificial neural network (ANN) statistical analysis method was used to develop a relationship between the body parameters and the BCF with an r2=0.96 and RMSE=1.01 using all top and side variables.

Affective computing has emerged as a prominent technology in recent years, driven by the increasing demand for machines capable of understanding and interpreting emotions. The COVID-19 pandemic has intensified this need by reducing physical interactions and increasing reliance on digital communication, which often involves complex emotional exchanges. To enhance social interactions by identifying and addressing negative emotions, an interactive emotion-perception system based on multi-sensing interfaces and affective computing has been proposed. Integration of gesture, voice, and brainwave sensors is employed to provide users with a rich sensory experience and immersive environment. Design principles and system development processes are derived from the affinity diagram method and prototype development approach. The proposed system was constructed, and experiments were conducted with 60 participants. Interpersonal interaction scenarios were explored to understand emotional transmission mechanisms, aiming to enhance user satisfaction and positive interpersonal experiences. Data were collected through indirect observation and questionnaires, followed by evaluation and statistical analysis. Findings include: (1) The emotion-perception system enhances positive interpersonal interactions by identifying 36 distinct emotions, with overall user emotions being positive but exhibiting notable individual variations; (2) The system effectively stimulates positive emotions and strengthens interpersonal interactions, with affective computing technology fostering enjoyable emotional resonance and high-quality relationships; (3) A positive correlation was observed between semantic analysis and brainwave metrics of relaxation and concentration, showing increased concentration and enhanced positive emotional interactions during message transitions; and (4) The multi-sensing and affective computing technology provides a pleasant and relaxing emotional journey, with interactions shifting from enthusiasm to comfort, demonstrating the system’s capacity for a satisfying and enjoyable experience.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

Powders with phase composition including syngenite K2Ca(SO4)2·H2O and/or calcium sulfate di-hydrate (gypsum) CaSO4·2H2O were synthesized from powder of calcium carbonate CaCO3 and water solutions of potassium hydrosulfate KHSO4 of various (0.5M, 1M and 2M) concentrations. Molar ratio of starting salt KHSO4/CaCO3=2 were used to provide formation of syngenite K2Ca(SO4)2·H2O. But when using 0.5M water solution of potassium hydrosulfate KHSO4 the phase composition of synthesized powder was presented by calcium sulfate dihydrate (gypsum) CaSO4·2H2O. When using 1M and 2M water solution of potassium hydrosulfate KHSO4 the syn-genite K2Ca(SO4)2·H2O was found as predominant phase in synthesized powders. According es-timations made from thermal analysis data when 1.0M and 2.0M water solutions of potassium hydrosulfate KHSO4 were used the content of calcium sulfate dihydrate (gypsum) CaSO4·2H2O in these powders were not higher then as 7.9 and 1.9 % respectively. Phase composition of products isolated from mother liquors via water evaporation consisted of syngenite K2Ca(SO4)2·H2O and potassium sulfate (arcanite) K2SO4. Synthesized powders can be used in preparation of biocom-patible bioresorbable materials with phase composition in the K2O‑CaO‑SO3‑H2O system; as matrix of thermo- or photo-luminescent materials; as components reducing the setting time and increasing strength of sulfate cements; in the fertilizing industry and also as a components of Martian regolith simulant.

The cement industry is a significant contributor (around 8 %) to CO2 global emissions. About 60 % of emissions come from limestone calcination, essential for clinker production, while 40 % result from fuel combustion. Reducing these emissions is challenging due to limestone’s role as the primary raw material for cement. Cement plants are required to achieve carbon neutrality by 2050, as outlined in the 13th United Nations Sustainable Goals. One strategy to achieve this goal, involves Carbon Capture and Utilisation (CCU). Among the options for CO2 utilisation, the Power-to-Liquid (PtL) strategy offers a means to mitigate CO2 emissions. In PtL, CO2 captured from cement industrial flue gas is combined with hydrogen generated by renewable electrolysis (green hydrogen) and catalytically converted into renewable methanol (e-MeOH). In this sense, this review provides a comprehensive overview of the worldwide existing pilot and demonstration units, and projects funded by EU across several industries. It specifically focuses on PtL technology worldwide within cement plants. This work covers 18 locations worldwide, detailing technology existent at plants of different capacities, location, and project partners. Finally, the review analyses techno-economic assessments related to e-MeOH production processes, highlighting the potential impact on achieving carbon neutrality in the cement industry.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

The construction industry is a key driver of environmental change due to its extensive ‎use of resources and high levels of emissions, thus placing a significant burden on global ‎efforts towards sustainable development targets. A large portion of the environmental ‎footprint of buildings results from the energy required to sustain indoor comfort levels. ‎Therefore, enhancing the energy efficiency of existing buildings becomes critical in ‎reducing their environmental impact. This study examines the influence of increasing ‎thermal performance with the aim of reducing heating ‎demand. Thus, numerical modelling tools and different energy performance assessment meth-odologies have been used. ‎Specifically, it evaluates two existing residential buildings in Romania and compares ‎heating demand predictions using PHPP and Mc001-2022 methodologies across various ‎climatic data sets and case studies. The results reveal significant variability in heating ‎demand predictions, emphasizing the importance of methodological choice and climatic ‎data. The ‎study highlights that both PHPP and Mc001-2022 methodologies yield varying results ‎depending on the specific conditions and characteristics of each building. This variation in results underscores ‎the necessity for a nuanced and context-specific approach to energy performance ‎assessment, in-corporating multiple energy efficiency measures tailored to the unique ‎features of each building.

The acoustic environment in learning spaces significantly influences learning effectiveness and occupant well-being. Recent studies have shown that a series of architectural factors within physical learning environments can impact students' educational experiences. This research delves into the relationship between architectural characteristics and the perceived acoustic environment among 467 primary students in 19 learning spaces across 9 schools in Chile. The survey comprises a student questionnaire, a checklist evaluating space characteristics, and acoustic measurements of indoor noise levels during occupied conditions. Examined topics include Indoor Environmental Quality (IEQ) comfort perception, noise annoyance, hearing ability, and acoustic preference. Architectural characteristics considered encompass flexible and acoustic space design parameters. The results indicated that noise discomfort was a common issue, especially in traditional learning spaces without acoustic treatment. The type of learning space (traditional or flexible settings) has a greater impact on acoustic perception particularly concerning noise discomfort and acoustic preference. However, poorly acoustic spaces lacking absorbing materials or exhibiting lower spatial density (m2 per student) contribute to increased indoor noise levels affecting noise annoyance caused by children's talking inside. The study emphasizes the importance of considering both architectural design and acoustic conditioning for optimizing the acoustic experience in educational spaces.

Sustainable development (SD) is essential to reduce and mitigate climate change impacts, environmental deterioration and to increase social sustainability. SD is therefore highly relevant for the engineering profession and is today found integrated with the higher education of specific engineering programs. This paper investigated the knowledge of SD for students entering the master’s program in Sustainable Building Information Management (BIM) by comparing levels of knowledge at the start and end of the first course Sustainability, Analyses and Simulations. The level of knowledge of SD was analyzed by classifying students’ conceptions of sustainability using SOLO taxonomy and the spectrum of liminality and the threshold concept. Students written responses to the question “What do you know about sustainability?” and written group project reports were used for analyzing levels of knowledge of SD. Levels of knowledge of SD was classified as pre (pre-liminal or pre-structural); uni-structural, multi-structural, relational and post-stages (extended abstract or post-liminal). In total, 68% of the students entering the master’s program in 2017 and 88% in 2018 showed a pre-structural, uni-structural and multi-structural SD knowledge. In general, few students entering the program showed relational and post-stages of SD knowledge, 32% and 12% of the students in 2017 and 2018, respectively. The students at the post-stage were able to express themselves more individually and creatively compared to previous levels in that they could connect the dimensions of SD to the context of SD of buildings, but also argue why SD of buildings was important and they could also suggest actions or tools for improved SD that engineers should use. Only one group of five (in 2017) showed a post-stage level of knowledge in the group project report. It is likely that the student’s general approach to the work with the reports was to mainly cope with the course requirements which is a sign of surface approach to learning. It, therefore, seems reasonable that future developments of the course should ensure that the students use the scientific literature in their group project reports to make it easier for them to understand the relationship between software use and the connection to green buildings certificate systems and SD of buildings. By making it mandatory to include scientific literature in the reports the students will be encouraged to read and think critically, and deeper, and to put the practical implementation of the software analysis results into a scientific context of SD and BIM.

This research analyzes the phenomenon of the reduction of urban green spaces in the post-socialist city. Belgrade was selected as a post-socialist city of the former Yugoslavia. The article analyses the views of urban planners on the reasons for the reduction of urban green areas in the post-socialist city based on semi-structured interviews with representative samples for urban areas. This result research confirms the hypothesis that post-socialist city planning reduces urban green areas due to the lack of new mechanisms in documents for the planning of urban green space. The concept of sustainability should connect and balance the skills of urban planners and focus on how urban planners develop and apply standards and protect them in market-democratic systems. In other words, a new mechanism of post-socialist city planning implies a balance between the private and public sectors. In the planning document, urban planners should find a common denominator between the public interest, citizens, investors, and spheres determined by the sustainable principles of the development. City institutions should provide opportunities for the application of those standards. With the new approach, planning would imply work in the service of citizens in the concepts of a sustainable and green city.

Turkana County's fisheries sector, which is entirely dependent on Lake Turkana, is vital to the county's economy. The Fisheries Sector in the County supports 1,500 households directly and 1,100 households indirectly. Despite its economic and social importance, the sector faces numerous challenges such as high post-harvest fish losses, uncoordinated development approaches, over-exploitation of some lake areas and weak links between research, management, and other sector players. Furthermore, since the start of devolution in 2013, the sector has been operating without an overall policy and legal framework. The primary goal of the study was to identify important challenges in the management of the fisheries sector in Turkana County that would lead the successful and coordinated growth of the fisheries industry. To capture their perspectives on the problems and potential in the usage of Lake Turkana's fisheries resources, semi-structured questionnaires and Key Informants interviews were used to collect primary data from the sector's fisheries actors. A total of 60 people were interviewed, and their responses were recorded in the Kobo Collect toolbox for later analysis. Secondary data was also gathered from numerous national policy declarations, guidelines, and legislation that have been used to manage Lake Turkana's fishery resources. The findings indicate that a policy directing the exploitation and development of fisheries is required in order to fully realize the potential of fisheries and aquaculture in the County. The development of the policy will lay a solid foundation for the creation of a legal framework to strengthen the sector in Turkana County, which is a necessary step toward achieving sustainable development and management of fisheries in accordance with national, regional, and international frameworks. By leveraging the role of the County Directorate of Fisheries and Beach Management Units in the sectors' monitoring, management, and development, the policy will also promote effective coordination of stakeholders at all levels.

Extracting the economic value by integrated utilization of space in old communities is crucial for encouraging independent participation from enterprises and residents, reducing reliance on government leadership and fiscal investment. This study starts from the active perspective of spatial assets, constructs a value activation framework for old community spatial assets by balancing "endogenous demand" and "exogenous opportunities." By enhancing "economic value" through "use value," five methods for value extraction and overall project utilization paths are proposed, guided by a dynamic "cost-revenue" balance. Using multi-source data, we identify the spatial assets of 1,096 old communities in central Guangzhou and apply a market comparison method for economic value assessment. Additionally, the study offers recommendations on timing and project portfolios for regeneration efforts, along with strategies for establishing a coordinating implementation entity and fund account. This research provides strategic insights for advancing the regeneration of old communities by tapping into their macro-level economic potential.

In order to quickly develop a multi ship collaborative collision avoidance plan in multi ship encounter scenarios, a multi ship collision avoidance decision model is proposed in accordance with the requirements of the International Maritime Collision Avoidance Regulations, taking into account the collision avoidance operations in multi ship encounter scenarios. Firstly, the collision risk between ships is determined by the closest encounter distance (DCPA) and closest encounter time (TCPA). Secondly, a decision objective function is established based on rules, degree of ship deviation, and ship risk. Finally, the prediction mechanism is used to calculate the minimum value of the objective function and complete the collision avoidance decision. The simulation results show that in the scenario of multiple ship encounters, the collision avoidance model can achieve safe collision avoidance with a smaller steering frequency and a shorter col-lision avoidance time. The proposed multi ship collision avoidance model can provide reference for collision avoidance decision-making in multi ship encounter scenarios, which helps to im-prove the collision avoidance efficiency in multi ship collision avoidance

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

Carbon (C) losses due to the conversion of natural forests adversely affect the abiotic components of terrestrial ecosystems. In tropical China, rubber cultivation often extends from its traditional range to elevations of up to 1400 m. However, C storage in rubber plantations across elevation gradients is poorly understood. In this study, we investigated biomass and C storage along elevation gradients in two age groups (8- and 12-year-old) of rubber monoculture plantations in Xishuangbanna, Southwest China. We investigated the C distribution across various tree sections, ranging from aboveground biomass (AGB) to belowground biomass (BGB), including litter, big dead branches, and different soil depths. A significant negative correlation was observed between total ecosystem C stocks and elevation in both age groups of rubber plantations. The highest ecosystem C stock of 197.90 Mg C ha–1 was recorded at 900 m in 8-year-old plantations, whereas in 12-year-old rubber plantations, the highest value of 183.12 Mg C ha–1 was found at 700 m. The total ecosystem C stocks decreased to its lowest level at 1000 m in both the 8-year-old and 12-year-old plantations, ranging between 113.05 Mg C ha–1 and 125.75 Mg C ha–1, respectively. We concluded that the total ecosystem C stocks were negatively correlated with elevation and significantly decreased from 8.05% to 51.55% and 11.46% to 42.96% between 700 m and 1100 m in both 8-year-old and 12-year-old plantations, respectively. However, no correlation was observed between the total soil C stocks and elevation in either age group of rubber plantations. Regardless of elevation gradient, the total ecosystem C stock of 12-year-old rubber plantations was 1.98% greater than that of 8-year-old rubber plantations. Biomass was the second largest contributor, while soil accounted for 82% to 90%, and the other factors contributed less than 2% of the total ecosystem C stock in both age groups. These fluctuations in C stocks along elevation gradients in both 8- and 12-year-old plantations suggested that rubber growth, biomass and C storage capacity decreased above 900 m and that age and elevation are key factors for biomass and C storage in monoculture rubber plantations.

The construction industry, a major player in economic development, is facing increased pressure to address sustainability concerns amidst rapid population growth and urbanization. With global projections indicating a significant rise in building demand by 2050 , sustainability emerges as a crucial focus area and paradigm shift to enhance environmental friendliness, improved quality, and project outcomes. The UAE, renowned for its vibrant construction industry, offers a unique context for examining the integration of sustainable practices. The growing use of sustainable construction practices is growing in the U.A.E., where the built environment plays a key role in economic growth and environmental stewardship. The United Arab Emirates (UAE) aims to foster long-term sustainability while enhancing the standard of living for current as well as future generations by integrating social, environmental, and economic aspects within construction projects, while also reevaluating conventional sustainable development frameworks and embracing a Triple -Bottom Line approach. Through an exploration of the significance of sustainable construction materials, this researcher underscores the multifaceted benefits of locally sourced, recyclable, and renewable materials in reducing environmental impacts, fostering economic and social well-being, and improving overall project performance, and project management practices. The construction sector's role in economic development and its substantial environmental impact are discussed in, alignment with sustainable construction materials, sustainable construction practices, and the need to enhance environmental sustainability; and create healthier built environments. In the realm of sustainable construction materials, project management knowledge areas encompass a range of factors. These include the properties of materials sourced regionally;, the incorporation of recycled content;, considerations for indoor air quality, energy, and water efficiency parameters;, and how these properties relate to project scope, scheduling constraints, and challenges. Additionally, the availability of resources and competency levels, quality control standards, specifications, communication strategies, and stakeholder involvement play crucial roles. It is important to assess both the positive and negative risks associated with these elements across construction projects.

In this work, zinc oxide (ZnO)/ granular activated carbon (GAC) composites at different ZnO concentration (0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC) were prepared by an in-situ hydrothermal method and demonstrated synergistic photocatalytic degradation and ad-sorption of Rhodamine B (RhB). The thermal stability, morphological structure, elemental com-position, crystallographic structure, and textural properties of developed catalysts were charac-terized by thermal gravimetric analysis (TGA/DTG), scanning electron microscopy equipped with energy dispersive-x-ray (SEM-EDS), x-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) analysis. Successful loading of ZnO onto GAC was confirmed by SEM-EDS and XRD analysis. The BET surface areas of GAC, 0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC were 474 m2/g, 450 m2/g, 453 m2/g, and 421 m2/g, respectively. The decrease in GAC could be attributed to the successful loading of ZnO on the GAC surface. Notably, 0.5M-ZnO@GAC exhibited the best photocatalytic degradation efficiency of 82% and 97% under UV-A and UV-C light over 120 min, attributed to improved crystallinity and visible light absorption. The photocatalytic degradation parameters revealed that lowering the RhB concentration, raising the catalyst dosage and pH be-yond the point of zero charge (PZC) would favor the RhB degradation. Photocatalytic reusability was demonstrated over 5 cycles. Scavenger tests revealed that the hydroxyl radicals (•OH), su-peroxide radicals (O2−•), and photoinduced hole (h+) radicals play a major role during the RhB degradation process. Based on the TOC results, the RhB mineralization efficiency of 79.1% was achieved by 0.5M-ZnO@GAC. Additionally, GAC exhibited a strong adsorptive performance towards RhB with adsorption capacity and RhB removal of 487.1 mg/g and 99.5% achieved within 90 min equilibrium time. The adsorption characteristics were best described by pseu-do-second-order kinetics, suggesting chemical adsorption. This research offers a new strategy for the development of effective photocatalyst materials with potential for wider wastewater treat-ment applications.

To enable net zero sustainable thermal building energy this study develops an open-source thermal house model to couple solar photovoltaic (PV) and heat pumps (HP) for grid-connected residential housing. The calculation of both space heating and cooling thermal loads and the selection of HP is accomplished with a validated Python model for air-source heat pumps. The capacity of PV required to supply the HPs is calculated using an System Advisor Model integrated Python model. Self-sufficiency and self-consumption of PV and the energy imported/exported to the grid for a case study are provided, which shows that simulations based on the monthly load profile have a significant reduction of 43% for energy sent to/from the grid compared to the detailed hourly simulation and an increase from 30% to 60% for self-consumption and self-sufficiency. These results show the importance of more granular modeling and also indicate mismatches of PV generation and HP load based on hourly simulation datasets. The back-calculation PV sizing algorithm combined with HP and thermal loads presented in this study exhibited robust performance. The results indicate this approach can be used to accelerate the solar electrification of heating and cooling to offset the use of fossil fuels in northern climates.

Smartwatches are one of the most relevant fitness trends of the past two decades, and they collect increasing amounts of health and movement data. The accuracy of these data may be questionable and requires further investigation. Therefore, the aim of the present study is to validate smartwatches for use in triathlon training. Ten different smartwatches were tested for accuracy in measuring heart rate, distance (via global navigation satellite systems, GNSS), swim stroke rates and the number of swim laps in a 50 m Olympic-size pool. The optical heart rate measurement function of each smartwatch was compared to that of a chest strap. Thirty participants (15 females, 15 males) ran five 3-minute intervals on a motorised treadmill to evaluate the accuracy of the heart rate measurements. Moreover, for each smartwatch, running und cycling distance tracking was tested over six runs of 4,000 m on a 400 m tartan stadium track, six hilly outdoor runs over 3.4 km, and four repetitions of a 36.8 km road bike course, respectively. Three swimming protocols ranging from 200 m to 400 m were performed in triplicate in a 50 m Olympic-size pool, evaluating tracked distance and detected number of strokes. The mean absolute percentage errors (MAPEs) for the average heart rate measurements varied between 3.1% and 8.3%, with the coefficient of determination ranging from 0.22 to 0.79. MAPE results ranged from 0.8% to 12.1% for the 4,000 m run on the 400 m track, from 0.2% to 7.5% for the 3.4 km outdoor run, and from 0.0% to 4.2% for the 36.8 km bike ride. For the swimming tests, in contrast, the deviations from the true distance varied greatly, starting at a 0.0% MAPE for the 400 m freestyle and reaching 91.7% for the 200 m medley with style changes every 25 m. In summary, for some of the smartwatches, the measurement results deviated substantially from the true values. Measurements taken while road cycling over longer distances with only a few curves were in relative terms more accurate than for outdoor runs and even more accurate than for the 400 m track. In the swimming exercises, the accuracy of the measured distances was severely deteriorated by the medley changes among the majority of the smartwatches. Altogether, the results of this study should help in assessing the accuracy and thus suitability of smartwatches for general triathlon training.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

The present study analyzes students' weather-related hazard and risk literacy in Greece, a climate change hotspot region in the Eastern Mediterranean. In this context, we examine the students' level in two core literacy variables, namely knowledge and competency. In addition, we explore how knowledge, attitudes and socio-demographic variables influence students' competencies related to weather and climate risk assessment and adaptability. A questionnaire-based survey was conducted on 474 students aged 12-16. The regression results showed that knowledge significantly affects the level of competency. Self-belief and confidence in science were the most influential among the attitudinal variables. We conclude by discussing educational and behavioural issues highlighted as essential to address with targeted policies and measures in formal education complemented by non-formal educational activities.

Bamboo is the building material of the past and future. It offers numerous properties that make it versatile for various applications, including construction. Its impressive strength-to-weight ratio enables it to bear substantial loads and stresses, while its good elasticity allows efficient energy absorption. However, its mechanical properties can vary based on factors such as species, age, locations, methods, and treatment. Treating bamboo is essential to enhance its properties and durability. The literature provides various natural and chemical treatments which enhanced some of the properties but also reported a drawbacks on higher temperature, content and duration. This paper reviewed 57 articles from Scopus database, specifically focusing on article-document type publications from the years 2003 to 2023. Additional references were also incorporated to address concerns in properties, treatment and standards to provide systematic understanding. MATLAB was utilized for data text analytics. With extensive assessment on the articles, the following gaps and concerns were observed and recommends for further study and assessment such as for bamboo properties, the development of centralized guidelines and procedures for the preparation and processing; exploration of alternative materials to reinforce bamboo without compromising its ductility; development of joint connections, and testing of mechanical properties considering seismic, wind and vibration. For treatment methods, the standardization of procedures using natural, chemical or combination. Lastly, for bamboo codes and standards, assessment of existing codes and standards for testing the mechanical properties of bamboo highlighting the potential limitations and areas, uniformity, differences with all existing similar standards. By filling these gaps, it can support the reliability and robustness of bamboo as a sustainable material, fostering its promotion and adoption in construction industry.

The increasing demand for transporting people and goods, rail system is needed for enhancement. An architectural design of train station can significantly impact investment from any government. However, a proper guideline for designing the train station in tropical climate is not publicized. This review examine railway station design through an analysis of student design theses in Thailand, from 1983 to 2022. Furthermore, the building analyses on architectural design theory were done in terms of service area, form, entrance structure, roof structure, style, and design development. The analysis reveals curved and gable roofs are most frequent, followed by 3D curved roofs. HSR stations' main entrances are designed to represent local culture and save walking distance. Curved and gabled porticos provide the most extravagant main entryway, a feeling of grandeur and beauty. A public building's overlapping portico or curving gabled portico lends majesty and refinement to its façade. Architects and designers strive to make buildings more attractive and practical. Besides, university-designed stations prioritize conceptual design and functional space over cost. Finally, railway station design should prioritize transparency, connectivity, movement, and cost- and time-efficiency. Research gaps are identified, such as designing user-friendly for thermal comfort and design-for-all the railway station in tropical climate, are critical for future evaluation.

Implementing net-zero building design is a crucial step towards decarbonizing the built environment during the entire lifecycle of a building, encompassing both embodied and operational carbon. This paper presents a novel computational approach to design Life Cycle Zero-Carbon Building (LC-ZCB), utilizing parametric integrated modeling through the versatile Grasshopper platform and its plug-ins. The Department of Energy’s prototype residential building at New York Institute of Technology, optimized to fulfill the LC-ZCB target, serves as the base building for this comprehensive study. Four main influencing design parameters, namely geometry, construction technology, thermal resistance of the envelope, and on-site renewable energy production, are defined and three-hundred design combinations are evaluated through the assessment of the operational carbon (OC) and embodied carbon (EC). By incorporating bio-based materials in the design options, the influence of biogenic carbon on the whole carbon footprint of the building case study is addressed by utilizing the GWPbio dynamic method, which assumes 100-year time horizon and incorporates dynamic characterization factors based on time of pulse emissions and two variables: rotation of the biomass and storage period of carbon in products. Finally, to account for potential climate changes, future climate data and 2099 weather conditions are considered during the scenarios assessment. The results demonstrate the potential for achieving LC-ZCB when fast growing biobased materials are largely used as construction materials, fostering a more environmentally responsible future for the construction industry.

This research investigates the compatibility of conventional air conditioning with the principles of green building, highlighting the need for systems that enhance indoor comfort while aligning with environmental sustainability. Conventional cooling systems, though proficient in regulating indoor temperatures, encounter several issues when incorporated into green buildings. These include energy waste, high running costs, and a misalignment with eco-friendly practices, which may also lead to detrimental environmental effects and potentially reduce occupant comfort, particularly in retrofit situations. Given the emphasis on sustainability and energy conservation in green buildings, there is a pressing demand for heating, ventilation, and air conditioning (HVAC) solutions that support these goals. This study emphasizes the critical need to reconsider traditional HVAC strategies in the face of green building advances. It advocates for the adoption of innovative HVAC technologies designed for eco-efficiency and enhanced comfort. These technologies should integrate seamlessly with sustainable construction, use greener refrigerants, and uphold environmental integrity, driving progress towards a sustainable and occupant-friendly built environment.

In this paper, the effect of an exterior shading element (Iwan) on energy consumption in four different climatic regions, and for different geographical directions, has been investigated numerically and experimentally. By applying different materials and techniques and creating various elements and spaces, architects make hard climatic conditions more tolerable for residents. Iwan is one of the cooling elements which is used in different forms and dimensions in the Islamic architecture. In the present research, Iwan has been introduced as a climatic element in traditional and contemporary architectures and its role in reducing the energy consumption in buildings has been studied. In this respect, first, the thermal loads of a building without Iwan are computed by means of EnergyPlus software. Then, four different forms of Iwan are added to the above-mentioned structure along the four principal geographical directions, and the effect of Iwan on the reduction of thermal loads is analyzed for four different climates. Finally, the design parameters of Iwan, in terms of depth and form, that can help reduce the thermal loads in different climatic conditions are presented. The results show that the best position for using an Iwan is the south direction and the use of Iwan in temperate & humid, hot & humid, cold & mountainous and hot & dry climates could reduce the energy consumption in buildings by 32%, 26%, 14%, and 29%, respectively.

Probiotics are becoming more and more popular in the growing of fin and shellfish because these species are consumed worldwide and because different techniques are employed to maximize the productivity and efficiency of fin and shellfish. Probiotic Bacillus is one of the many types of probiotics that are used, but it stands out due to its superior qualities. For instance, because of its ability to sporulate, it can survive in harsh environments, produce antimicrobial substances, and is safe to feed to fish. The different species of Bacillus used in the farming of fin and shell fish were discussed in this review, along with the benefits of using Bacillus spp. as a good substitute in sustainable aquaculture to improve feed utilization, immune system response, stress adaptation, resistance to infectious diseases, tissue preservation integrity, and water quality. Additionally, we discussed the possible risks to safety that Bacillus poses when raising these significant species. For the purpose of future research and development regarding Bacillus application in aquaculture, a summary of the findings of recent studies about the advantages of applying Bacillus to enhance fin and shellfish aquatic animal culture has been provided.

Earth’s climate cannot be ignored any longer. Policies are vital in order to mitigate the negative effects of climate change. The energy crisis created by the Russo-Ukrainian war and pandemic affected the EU and its member states. The focus is more than ever on its energy policies and independence. The EU revised the energy strategy in response to Russia’s blackmail, and it sped up all the processes for energetic independence from Russia. This benefited the climate change policies the most, as all the measures involved reducing energy consumption and increasing renewables, thus contributing to reducing greenhouse gas emissions. As a member state of the EU, Romania is committed to complying with EU regulations. With a high degree of energy independence compared with the other EU members, Romania plans to become a regional energy provider and modernize the energy infrastructure internally as a response to Russia’s unprovoked aggression. The measures that the EU and Romania implemented after the war started in 2022 have come to fruition, and the effects are becoming visible a year later. This study aims to study the energy strategy of Romania in correlation with the EU strategy in the turbulent period of pandemics and war between 2019 and 2023, with the latest available data.