Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

The effects of climate change health impacts on urban health care systems and vulnerable populations are a researched topic with foundations on urban risk management, urban health methodologies, and sustainable urbanization. As climate change is a dynamic and transformative global issue the gap between adaptation and mitigation efforts and urban planning relies, among other things, in the limitations of previous studies of risk management structures tailored to the existing strategy to calculate the uncertainties and predict their influence on urban systems and subsystems. Moreover, as climate and health is a well-researched issue, it is also complex as the methodologies and strategic approach to minimize health risks of climate change is intrinsically contingent to risk methodologies and policy-making processes that are efficient with support of knowledge-based information. This paper emphasis the need for focusing on urban health risk management methods that serves to identify potential opportunities, and then manage and take action to prevent adverse health effects. It also emphasizes the probability of events and their consequences, which are measurable both qualitatively and quantitatively.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

Our study reviews the significance of archaeological parks in the tourism sector, with a specific focus on how digital presence and visitor feedback impact their cultural and touristic appeal. Utilizing statistical analyses such as regression and cluster analysis on data sourced from both Hungarian and Western European parks, the research scrutinizes TripAdvisor and Google ratings, alongside the volume of photographs and reviews. The findings highlight a modest correlation between digital visibility and overall visitor ratings, underscoring the complex relationship between online engagement and the quality of visitor experience. Notably, the cluster analysis identified two distinct groups, signifying diverse levels of visitor engagement and digital visibility across the parks. The conclusions drawn advocate for a comprehensive strategy to enhance visitor experiences, emphasizing the integration of digital engagement with the promotion of the parks cultural and historical values. By exploring the influence of digital presence on the appeal of archaeological parks, our study sheds light on the evolving interface between urban studies and digital heritage, highlighting how digital tools and online platforms are becoming increasingly integral in shaping the perceptions and experiences of urban cultural sites.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Long term Precipitation and temperature variations are one of the main determinants of climate variability of one’s area. The aim of this study is to determine trends variation in climatic elements of temperature and precipitation in the southern zone of Tigray regional state, Ethiopia. The station is assumed for the study of climatic records over southern zone of the region in detection for probable trends. The daily, monthly and annual precipitation totals and temperature observed at korem meteorological station were used for the period of 1981-2010 for Precipitation and 1985 – 2010 for minimum and maximum temperature. Summary of descriptive statistics and Mann Kendall test methods were employed for the observed data analysis to demonstrate any existence of possible trends. The main findings of the study indicated that the mean and maximum temperature had a general increasing trend; however, minimum temperature showed decreasing trend. In general annual temperature from 1985 – 2010 of the area showed a warming trend. Moreover analysis of the 30 years (1981-2010) annual precipitation showed a coefficient of variation ranging from 33.77 – 233 %. It indicated that the precipitation dissemination is not normal with large year to year variances.

Hierarchical tungsten oxide assemblies such as spindle-like, flowers with sharp petals, nanowires and regular hexagonal structures are successfully synthesized via a solvothermal reduction method by simply adjusting the reaction conditions. On the basis of the experimental results, it is determined that the reaction time significantly influences the phase transition, microstructure and photocatalytic activity of the prepared samples. The possible mechanisms for the phase transition and morphology evolution process have been systematically proposed. Moreover, the as-prepared products exhibit significant morphology-depended photocatalytic activity. The flower-like W18O49 prepared at 6 h possesses large specific surface area (150.1 m²g^-1), improved separation efficiency of electron-hole pairs and decreased electron-transfer resistance by the photoelectrochemical measurements. As a result, the flower-like W₁₈O₄₉ prepared at 6 h exhibits the highest photocatalytic activity for the degradation of Methyl orange aqueous solution. The radical trap experiments showed that the degradation of MO was driven mainly by the participation of h⁺ and •O²⁻ radicals.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Tissue-like phantoms are widely used as a model for mimicking the optical properties of live tissue. This paper presents the results of a diffusion reflection method as well as fluorescence lifetime imaging microscopy measurements of fluorescein-conjugated gold nanorods in solution as well as inserted in solid tissue-imitating phantoms. A lack of consistency between the fluorescence lifetime results of the solutions and the phantoms raises a question about the ability of tissue-like phantoms to maintain the optical properties of inserted contrast agents.

Sustainability is a characteristic manifested in the ability to maintain the necessary level of performance for construction companies when risk factors arise during the implementation of investment and construction projects. The risk factors that arise during the implementation of in-vestment and construction projects differ in nature, degree of influence, and other characteristics. Ignoring these factors and measures to manage them often leads to critical consequences in the form of disruptions in the timing of work. Risk is a combination of the probability and consequences of the occurrence of adverse events. The article considers the concept of risk as a potential possibility of occurrence of adverse situations and related consequences when exposed to these factors. Risk factors are characterized by surprise, discreteness of changes, the presence of threshold values, upon reaching which a transition to a different mode of operation is required. The article discusses the risk factors arising at the construction stage, their classification. A methodology has been developed that includes conducting a survey in the form of a questionnaire in order to collect information about risk factors that affect the implementation of investment and construction projects. Experts with experience in the construction sector were involved in the survey. The processing of the survey results made it possible to assess the significance of various risk factors in investment and construction projects. Thus, statistical and expert methods were used in the study. The results showed that financial, technical, legal, economic, managerial and natural factors have the greatest impact on investment and construction projects. It is recommended to pay special attention to the listed factors when developing measures aimed at preventing risks and their consequences. The methodology described in the study can be used by construction companies in strategic planning. The analysis of the stability of construction companies, depending on their use of various ways to counteract risk factors, allowed us to develop a number of practical recommendations to reduce the impact of the studied factors on achieving the goals of investment and construction projects.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

In this study, an attempt was made to investigate the Kenya case of multivariate causality of carbon dioxide emissions by employing a time series data spanning from 1961-2011 using the ARDL method of cointegration analysis. The long-run elasticities show that, a 1% increase in financial development increases carbon dioxide emissions by 0.28%, a 1% increase in GDP per capita increases carbon dioxide emissions by 1.32% and a 1% increase in urbanization decreases carbon dioxide emissions by 1.14%. There was a unidirectional causality running from financial development, food production index, GDP per capita, industrialization and urbanization to carbon dioxide emissions. The innovation accounting shows that 20% of future shocks in carbon dioxide emissions are due to fluctuations in financial development, 9% of future shocks in financial development are due to fluctuations urbanization and 22% of future shocks in food production index are due to fluctuations in carbon dioxide emissions.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

During the last years there has been a high interest in the development of new purely-organic single-component conductors. Very recently, we have reported a new neutral radical conductor based on the perchlorotriphenylmethyl (PTM) radical moiety linked to a monopyrrolo-tetrathiafulvalene (MPTTF) unit by a -conjugated bridge (1). Interestingly, this system behaves as a semiconductor with high conductivity and small energy gap under high pressure. With the aim of developing a new material with improved conducting properties, we have designed and synthesized the radical dyad 2 which was functionalized with an ethylenedithio (EDT) group in order to improve the intermolecular interactions of the TTF subunits. The physical properties of the new radical dyad 2 were studied in detail in solution to further analyze its electronic structure as well as its potential use as radical conductor in the solid state.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The optimal structural design is imperative to minimize material consumption and reduce the environmental impact of construction. Given the complexity in the formulation of structural design problems, the process of optimization is commonly performed using artificial intelligence (AI) global optimization, such as Genetic Algorithm (GA). However, the integration of AI-based optimization together with visual programming (VP) in building information modeling (BIM) projects warrants further investigation. This study proposes a workflow by combining structure analysis, VP, BIM, and GA to optimize trusses. The methodology encompasses several steps including: (i) generation of parametric trusses in Dynamo VP; (ii) performing the finite element modeling (FEM) using Robot Structural Analysis (RSA); (iii) retrieving and evaluating the FEM results interchangeably between Dynamo and RSA; (iv) finding the best solution using GA; and (v) importing the optimized model into Revit, enabling the user to perform simulations and engineering analysis, such as life cycle assessment (LCA) and quantity surveying. The feasibility of the proposed workflow was tested on benchmark problems and compared with open literature. The outcomes of this study offer insight into the opportunities and limitations of combining VP, GA, FEA, and BIM for structural optimization applications, particularly to enhance structural efficiency and sustainability in construction.

With the growing trend of urbanization and the growing number of people migrating to cities, the demand for the development and construction of new buildings as well as the infrastructure has risen, meaning that the construction industry must adapt to the trends. The growing demands with shorter deadlines for an industry already known for high costs and not delivering on time means that productivity must be increased without increasing the cost. The solution for this might lie in the application of the Lean philosophy to the construction industry. This paper analyses the application of the Lean philosophy in order to increase the productivity in the airport construction site. The paper highlights the potential for enhancing productivity in construction workplaces by concurrently fostering continuous improvement and sustainability through the implementation of the A3 methodology and Lean principles, resulting in waste reduction and increased value.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

Lignin is insoluble in water, limiting its use in the synthesis of adhesives. Therefore, in order to increase the amount of lignin raw materials used in the synthesis of adhesives, a kind of aminated lignin compounds was prepared through lignin amination reaction, and conducting structural analysis in this paper. The particle size of the amino lignin is about 100 nm, with the weight average molecular weight of 57,627 g/mol and a water solubility of 0.45g/100ml. The reaction mechanisms were proposed that the phenolic hydroxyl groups of lignin react with ammonia molecules, and thereby successfully introducing amino groups to generate the aminated lignin compounds. Therefore, this article enriches the scientific theory of lignin reactions and provides reference for the widespread application of lignin raw materials in the field of adhesives.

In this study, carbon-quantum-dot (CQD)-decorated TiO2 was prepared using an ultrasonic doping method and applied in the photocatalytic degradation of naphthalene under sunlight irradiation. The CQDs were synthesized from a typical macroalgae via diluted sulfuric acid pretreatment and hydrothermal synthesis using an optimal design, i.e., 3 wt% and 200 oC, respectively. The CQD/TiO2 composite remarkably enhanced the photocatalytic activity. The degradation of naphthalene under a visible light environment indicated that there is a synergistic mechanism between CQDs and TiO2, in which the generation of reactive oxygen species is significantly triggered; in addition, the N that originated from the macroalgae accelerated the photocatalytic efficiency. Kinetic analysis showed that the photo-catalytic behavior of the CQD/TiO2 composite followed a pseudo-first-order equation. Consequently, our combined experimental approach not only provides a facile pretreatment process for bio-CQDs synthesis, but also delivers a suitable TiO2 photocatalyst for up-conversion, along with critical insights into the development of harmful macroalgae resources.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Published data or available literature on sustainable building plan-design, construction, performance, and renovation criteria have covered some stages or some parts of each stage. These data usually have been published partially in many different papers―there have not been any papers that published these data together. Hence, this paper aims to collectively review these data and publish them together. The collection and review of these data were carried out by our twenty-five team members who specialized in sustainable urban, architectural, and civil engineering and construction management. The gathered and reviewed outputs were combined and validated based on a general group consensus. This consensus decision-making proceeded through two major group meetings with several follow-up meetings. The first major meeting was to combine and improve the gathered reviewed sustainable building criteria for Cambodia. The second major meeting was to validate the improved reviewed sustainable building criteria for Cambodia. The several follow-up meetings were to discuss the relevance and importance of the validated data “criteria and their classifications and descriptions” in all stages and more focused on their importance and applicability to Cambodia. The collective reviewed data in this paper would be useful to researchers in the fields. They could also be useful collective knowledge and information for policymakers from governmental agencies and development partners, particularly for sustainable building and construction companies.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

The construction industry plays a crucial role in shaping the built environment and contributes to the global economy. However, the construction process is associated with negative impacts on the environment and communities. This paper examines the environmental impacts of construction and presents strategies for mitigating them, focusing on sustainable construction practices. The research draws on a comprehensive literature review, case studies, and expert interviews to fully understand the construction industry and its environmental effects. The findings indicate that the implementation of greater supervision of every construction project phase, using alternative design practices, and the use of sustainable construction practices can reduce the negative impacts of construction on the environment and society. The study concludes that sustainable construction practices can contribute to a better environment for a better quality of life and should be embraced by the construction industry. The recommendations for future work include the adoption of green building standards, the use of renewable energy sources, the reduction of waste, and the promotion of stakeholder engagement. Future research should focus on the evaluation of the effectiveness of these strategies and their scalability.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

A pump station is a very important flood control facility for mitigating inundation of urban lowland areas. It is not easy to secure a site to increase the capacity of a pump station in an urban area because of various limitations or to maximize the discharge capacity of the pump sump. Adding a facility to improve the pump capacity of a pump station may affect the flow characteristics, such as unexpected increases in the flow velocity and vorticity, and cause severe problems with operating the pump station. To solve those problems, anti-vortex devices (AVDs) have been developed and adopted for appropriate design standards. The Korean design criteria for AVDs are based on experience and foreign standards because not enough data on the AVD are available. In this study, the flow in the sump was numerically simulated at various AVD heights to collect information on improving the design and efficiency of a pump station. Consequently, an appropriate height for the AVD and changes in the flow pattern and vortex in the pump sump were determined and compared with 12 cases of inflow conditions with respect to the vertical location.

The collapsible loess will rapidly soften and lose its bearing capacity when soaked in water. Under a mild condition (20°C), the biomimetic inorganic agent, Diammonium phosphate (DAP), reacts with calcite in the collapsible loess, producing a stronger bonding material, hydroxyapatite (HAP), to modify and stabilize the soil. Uniaxial compression, permeability tests and morphological analysis using XRD and SEM/EDX microscopy were carried out to assess the effectiveness of DAP stabilization on the collapsible loess. The results indicated that HAP improved the inter-particle bonding within loess, filled the pores within particles, reduced the permeability, and consequently mitigated collapsibility of loess. The compressive strength of DAP-treated loess increased as DAP concentration increased. Following 28-days curing, the compressive strength of the loess treated with a 3.0 mol/L DAP solution was six times greater than that of the untreated group. DAP's reinforcement effect on loess was superior to that of cement. The compressive strength of DAP-treated loess was about double that of cement-treated loess and the permeability coefficient was reduced by more than 50% at equivalent solid content. Furthermore, DAP generated 68% fewer carbon emissions compared to Portland cement. Considering eco-friendly and sustainable development, DAP offers a more competitive alternative for modification and stabilization of loess.

Advanced lithography requires highly sensitive photoresists to improve lithographic efficiency, and it is critical yet challenging to develop high-sensitivity photoresists and imaging strategies. Here, we report a novel strategy for ultra-high sensitivity using hexafluoroisopropanol (HFIP)-containing fluoropolymer photoresists. The incorporation of HFIP, with its strong electrophilic property and electron-withdrawing effect of the fluorine atoms, significantly increases the acidity of the photoresist after exposure, enabling imaging without conventional photoacid generators (PAGs). The HFIP-containing photoresist has been evaluated by electron beam lithography to achieve a trench of ~40 nm at an extremely low dose of 3 μC/cm2, which shows sensitivity enhancement by ~10 times to the commercial PAGs involved system, revealing its high-sensitivity and high-resolution features. Our results demonstrate a new type of PAGs and a novel approach to higher-performance imaging beyond conventional photoresist performance tuning.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

Over the past few decades, synthetic polymer production has increased, and the production of plastics has surpassed all other man-made materials due to their versatility. Moreover, packaging plastic makes up around 40% of global plastic production. However, the excessive usage of synthetic packaging materials has led to severe environmental and health-related issues. Therefore, biobased packages are considered alternatives to substitute synthetic packaging on the market. Furthermore, the choice of packing material in the food industry is a perplexing process as it depends on various factors, such as the type of food product, its sustainability, and environmental conditions. Interestingly, due to proven gas barrier properties and biological activity, polysaccharide-based bioplastics show the potential to expand the trends in food packaging, including edible films and intelligent and active food packaging. This review discusses the structure, properties and recent developments in polysaccharide-based bioplastics as food packaging materials.

A method for accurately determining the chemical composition of deposits at the bottom of pores during the electrocoloring (e-coloring) of aluminum anodic oxide (AAO) layers in tin-based solutions is developed. The aluminum samples were AC e-colored after DC sulfuric anodization. Free-standing, tin e-colored aluminum oxide film was obtained by selective dissolution of the metallic aluminum from the AAO in copper chloride solution to access the deposit directly at the bottom of the pore. This allowed us to take XPS analysis directly from the deposits at pore bottoms without any interference from the base material or insulating barrier layer. The results revealed the presence of a mixture of tin oxide and metal in the deposits, which were richer in oxide content. Furthermore, a cyclic voltammetry experiment mimicking real polarization conditions during AC conditions was optimized and used to gain a deeper understanding of the electrochemical reactions that occur during AC electrocoloring. The comparison of CV results in tin-free and tin-containing electrolytes indicated that the tin deposited during a cathodic cycle is oxidized in the anodic cycle. The formation of tin based deposits radically changed the CV behavior. The XPS and cyclic voltammetry results consistently show that the deposits formed during e-coloring comprised a mixture of metallic and oxidic tin species richer in oxide content.

Green carbon-based materials (GCM), i.e. carbon materials produced using renewable biomass or recycled wastes, ought to be used in order to processes become sustainable and carbon neutral. Carbon nanomaterials, like for example carbon dots and nanobichar families, and carbon materials, like for example activated carbon and biochar substances, are sustainable materials with great potential to be used in different technology applications. In this review, the following four applications were selected, and the works published in the last two years (since 2022) critically reviewed: agriculture; water treatment; energy management; and, carbon dioxide reduction and sequestration. GCM improved the performance of the technological applications under revision and play an important role in the sustainability of the processes, contributing to the mitigation of the climate change, namely by reducing emission and increase sequestration of CO2eq..

Motion related human activity recognition using wearable sensors can potentially enable various useful daily applications. So far, most studies view it as a stand-alone mathematical classification problem without considering the physical nature of human motions. Consequently, they suffer from data dependencies and encounter the dimension disaster problem and the over-fitting issue, and their models are never human-readable. In this study, we start from a deep analysis on natural physical properties of human motions, and then propose a useful feature selection method to quantify each feature's classification contribution capability. On one hand, the "dimension disaster" problem can be avoid to some extent, due to the affined dimension of key features; On the other hand, over-fitting issue can be depressed since the knowledge implied in human motions are nearly invariant, which compensates the possible data inadequacy. The experiment results indicate that the proposed method performs superior to those adopted in related works, such as decision tree, k-NN, SVM, neural networks.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

This bibliographic study addresses key aspects related to fishing, product safety, and climate change in the Adriatic Sea region. The examination of product safety focuses on the assessment of contaminants originating from human activities such as industry, mining, agriculture, and household waste disposal. The contamination of the aquatic environment has emerged as a pressing global concern, extending to the Adriatic subbasin. Aquatic organisms, including fish, are prone to accumulating pollutants directly from polluted water sources and indirectly through the food web. The bio-accumulation of potentially hazardous substances, particularly heavy metals, pesticides, PCBs, PAHs, and antibiotic resistance in aquatic organisms, poses a significant threat to human health. Climate change effects will deplete our seafood supply in terms of quantity and safety owing to negative consequences such as higher levels of pollution, parasites, viruses, infections, acidification, and toxicities such as shellfish poisoning. Global food safety strategies should be developed to reduce greenhouse gas emissions and promote environmentally friendly technology, which indirectly affects seafood quality and microbiological safety, especially for Adriatic Sea, which is part of the Mediterranean Sea, characterized by the most polluted waters in the world.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Faba bean is an important legume crop wordwide, grown both for food and feed. As for many legume crops, postemergence weed control is difficult. The aim of this work was to assess potential of intercropping on weed management by assessing the effect of mixing faba bean with different crops (wheat, barley, and pea) on weeds in the South of Spain. Four field trials were conducted over four consecutive seasons, and results found that addition alternate intercropping of faba bean and barley achieved high levels of weed control, both for coverage and biomass (92.7% and 76.6%, respectively). Intercropping with wheat did not reduce weed coverage but did decrease weed biomass by 46.1% as compared to faba bean monocrop. Intercropping with pea did not provide significant reductions for weed coverage neither for weed biomass. The diversity of the weed community was not altered by the different crop combinations tested. Additional experiments under controlled conditions were carried out to determine a possible role of barley allelopathy in weed suppression. A strong allelopathic effect entailing a reduction in the number of plants and biomass was detected for four weeds: Sinapis arvensis, Polypogon monspeliensis, Matricaria camomilla, and Medicago trucatula. It can be concluded that intercropping faba bean with barley is an excellent strategy for weed control in the Southern Spain.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

Proteins have the ability to adsorb on the surface of materials, such as soft contact lenses (SCLs), and can affect the hydrophobicity, roughness and surface properties of the contact lenses (CLs), which, in turn, can influence the friction between the lenses and the ocular surface. Excessive friction between contact lenses and the ocular surface can lead to discomfort for the wearer and may cause irritation or inflammation of the cornea, better known as corneal ulcers (keratitis). Bovine serum albumin (BSA) is often used as a standard protein in biocompatibility testing of materials, including contact lenses. One standard commercial contact lenses was tested under lubricated conditions to access the coefficient of friction (CoF), being the contact lubricated with a tear like fluid (TLF) solution containing six different concentrations of BSA. In all cases, a good linearity of the results of the friction force was verified, so the first friction law can be applied to determine the value of the coefficient of friction. It was found that friction increases with increasing protein concentration.

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides were prepared, varying nominal cerium com-positions (x=0, 0.2, 0.3, and 1). The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, rang-ing from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in textural properties of the catalysts was noted, being particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under two contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface ar-ea in loose contact mode. Notably, the T10 and T50 parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511℃ and 538℃ for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed a significant relationship emerges between work function values and the formation of oxy-gen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter which showed better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Smart manufacturing encompasses a category of manufacturing that employs computer-integrated capabilities and technologies to enhance supply chain optimization, production efficiency, and recyclability. Yet limited studies have been conducted to optimize these prospects from the perspective of low resource countries where such innovative studies have not been adequately explored. This paper aims to examine the implications of smart manufacturing practices (Smart Procurement, Smart Supply Chain, Smart Production Planning and Control, Automation and Industrial Robot, and Supply Chain Configuration) on pro-environmental behaviour and develop a baseline moderated mediation model to explain the relationship between smart manufacturing and pro-environmental behaviour with a role of green dynamic capability, and environmental orientation. This study is anchored on quantitative research approach, deductive reasoning, and explanatory design. Cross – sectional survey data have been obtained from 382 manufacturing companies in Ghana. Our hypotheses have been tested using Structural Equation Modelling and SMART-PLS version 3.8.9. The study has revealed that smart manufacturing practices significantly and positively relate to pro-environmental behaviour. Moreover, green dynamic capability and environmental orientation moderate the relationship between smart manufacturing and pro-environmental behaviour. The implications of the study include the emergence of a baseline model to guide policymakers, practitioners, and academicians to explain the relationship between smart manufacturing and sustainable manufacturing in the context of developing countries. Again, the social implication of the study includes the realisation of decent job and economic growth, responsible consumption and production as well as actions taken to combat climate change.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

The physical roots, interpretation, controversies and precise meaning of the Landauer Principle are surveyed. Landauer's principle is a physical principle pertaining to the lower theoretical limit of energy consumption of computation. It states that an irreversible change in information stored in a computer, such as merging two computational paths, dissipates a minimum amount of heat kBTln2 per a bit of information to its surrounding. The Landauer Principle is discussed in the context of fundamental physical limiting principles, such as the Abbe diffraction limit, the Margolus-Levitin limit and the Bekenstein limit. Synthesis of the Landauer bound with the Abbe, Margolus-Levitin limit and Bekenstein limits yields the minimal time of computation, which scales as τmin~hkBT. Decrease in a temperature of a thermal bath will decrease the energy consumption of a single computation, but, in parallel, it will slow the computation. The Landauer principle bridges between John Archibald Wheeler “it from bit” paradigm and thermodynamics. Experimental verifications of the Landauer Principle are surveyed. Interrelation between thermodynamic and logical irreversibility is addressed. Generalization of the Landauer principle to the quantum and non-equilibrium systems is addressed. Landauer Principle represents the powerful heuristic principle bridging the physics, information theory and computer engineering.

This study aimed to investigate the relationship between sleep duration, dementia severity, age, and ANS regulation. This cross-sectional pilot study included 27 older patients with probable Alzheimer’s disease, hospitalized at a psychiatric center. We measured heart rate variability to assess ANS regulation at night, evaluated dementia severity using the Clinical Dementia Rating scale, and obtained sleep duration data from sleep diaries maintained by psychiatric nurses. The data were analyzed using repeated-measures generalized linear models with age, sex, dementia severity, and medication (antipsychotics) as covariates. A sleep duration of 7–8 h per night was associated with better ANS regulation than other sleep durations, as indicated by sympathovagal balance (p = 0.005). ANS dysregulation was characterized by a 20.7% increase in sympathetic nervous system activity and a 14.8% decrease in parasympathetic nervous system (PSNS) activity. We found a significant correlation between dementia severity and PSNS activity (p = 0.04) and observed an inverted U-shaped association between sleep duration and ANS regulation. This pilot study demonstrated that a sleep duration of 7–8 h per night may be critical in maintaining optimal ANS regulation. Bidirectional associations between sleep duration, inadequate sleep duration, aging, and ANS regulation warrant further investigation.

Wearable touch sensors, which can convert force or pressure signals into quantitative electronic signals, have emerged as an essential smart sensing devices and played an important role in various cutting-edge fields, including wearable health monitoring, soft robots, electronic skin, artificial prosthetics, AR/VR, and the Internet of Things. Flexible touch sensors have made significant advancements, while construction of novel touch sensors via mimicking the unique properties of biological materials and biogenetic structures always remains a hot research topic and significant technological pathway. This review provides a comprehensive summary of the research status of wearable touch sensors constructed by imitating the material and structural characteristics in nature, and also summarizes the scientific challenges and development tendency of this aspect. Firstly, the research status for constructing flexible touch sensors based on biomimetic materials is summarized, including hydrogel materials, self-healing materials, and other bioinspired or biomimetic materials with extraordinary properties. Then, design and fabrication of flexible touch sensors based on bionic structures for performance enhancement are fully discussed. These bionic structures include special structures in plants, special structures insects/animal, and special structures in human body. Moreover, a summary of the current issues and future prospects for developing wearable sensors based on bioinspired materials and structures is discussed.

In this review, we summarize recent progress in crystal growth and understanding the influence of crystal structure on the superconductivity in pure and Pb-doped Bi2Sr2CuOy (Bi-2201) materials belonging to the overdoped region of high temperature cuprate superconductors. The crystal growth of Bi-2201 superconductors faces challenges due to intricate materials chemistry and lack of knowledge of corresponding phase diagrams. Historically, a crucible-free floating zone method has emerged as the most promising growth approach for these materials, resulting in high-quality single crystals. This review outlines the described in the literature and the authors' synthesis endeavors, encompassing Pb-doped Bi-2201 crystals, detailed structural characterization of as-grown and post-growth annealed samples, and highlights optimal growth conditions that yield large-size, single-phase, and compositionally homogeneous Bi-2201 single crystals.

Motivated by diffraction experiments on the $\left(2\sqrt{3}\times \sqrt{3}\right)\mathrm{R}{30}^{\circ }$ reconstructed Si(111) due to deposition of rare earth elements (Dy, Tb) and silicide formation we analyse the splitting and non-splitting of superstructure spots. For this purpose, we model diffraction patterns for one dimensional structures generated by the binary surface technique and use supercell models to keep the analysis simple. Diffraction pattern are calculated in the framework of the kinematical diffraction theory and they are analyzed as a function of the domains and domain boundaries. Basic properties of the diffraction pattern are analyzed for model systems of a two-fold and a three-fold periodicity. The rules derived from these calculations are applied to the "real-world" system of Si(111)-($\left(2\sqrt{3}\times \sqrt{3}\right)\mathrm{R}{30}^{\circ }$)-RESi$2_{}$ (RE = Dy or Tb). Depending on the combination of domains and domain boundaries of different types a plethora of different features are observed in the diffraction patterns. These are analyzed to determine the sizes of both domain boundaries and domains from experimentally observed splitting of specific superstructure spots.

The production of concrete and the manufacturing process of cement results in a significant carbon footprint, contributing to a large portion of global emissions in structures such as buildings, bridges, roads, and tunnels. Although concrete is an ideal building material that is durable and long-lasting, it can be susceptible to micro-cracks. These micro-cracks in concrete can allow water and chlorine ions to penetrate the structure, leading to the degradation of concrete and corrosion of the reinforcement, posing an unacceptable level of structural risk. Self-healing concrete is not a new material in the construction industry but can be characterized by the capability of concrete to repair its cracks autogenously or autonomously. Recent advancements in concrete research and technology have given us a better understanding of concrete's healing properties. Self-healing concrete combines durability with sustainability while offsetting the high carbon output of concrete manufacturing and production and associated life-cycle costs. Technologies such as microbially-induced calcite (calcium carbonate) precipitation (MICP), shape memory polymers, encapsulation methods, hydration, and swelling agents can potentially reduce carbon emissions while enhancing resilience and longevity. This paper examines these technologies and their applications in the construction industry by comprehensively reviewing the literature and available case studies. The study concluded that there are promising advancements and innovations in concrete, particularly when improving upon the autogenous healing properties. The recommendations for future research include exploring more ways to bring the concrete industry and cement manufacturing toward net zero carbon emissions.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

Failure to meet the deadlines for the implementation of investment and construction projects is a problem in all countries of the world, and leads to unstable activity of construction companies. The article studies the most important destabilizing factors affecting the main indicator of sustainable activity of construction companies-the duration of the implementation of an investment and construction projects. To determine and assess the impact of destabilizing factors on the duration of implementation of selected investment and construction projects, a survey was conducted, in which a number of customers, consultants and contractors involved in construction projects took part. Questionnaires developed on the basis of a cluster sample were sent to respondents, 48 responses were received in response to the assessment of destabilizing factors. To analyze the received and grouped information, structural equation modeling using the Smart-PLS program was used. As a result of modeling, a number of results were obtained, the most important of which are the identification of the main reasons that lead to an average (20% - 50%) increase in the duration of projects in the construction sector. The most significant were: the lack of an appropriate procurement program for materials; inefficient scheduling by contractors and instability of construction production; poor-quality processing of incoming information and untimely deci-sion-making due to changes in projects during their implementation. Destabilizing factors con-tribute to an increase in the duration of construction sector projects, which leads to time overruns, cost overruns, and an increase in the negative impact on the overall use of resources. As a result of the study, a set of recommendations was formed, the most important of which is the use of possible compensatory measures that can allow construction companies to eliminate the risks of disrupting construction deadlines for sustainable activities. These compensatory measures include: - recommendations to customers of the construction project; - recommendations to contractors; - recommendations to the consultant. Moreover, the control of destabilizing factors that can cause delays, the improvement of contracts and the precise and clearer definition of all elements of the project can help to reduce the duration of construction, and will allow companies to maintain sustainable activities in the construction industry.

Additive manufacturing, commonly referred to as 3D printing, is an exciting and versatile manufacturing technology that is gaining traction and interest in both academic and industrial settings. Polymeric materials are essential components in a majority of the “inks” used across the various 3D printing technologies. As the environmental ramifications of sole or primary reliance on petrochemicals as a resource for industrial polymers continue to manifest themselves at a global scale, a transition to more sustainable bioderived alternatives could offer solutions. In particular, cellulose is promising due to its global abundance, biodegradability, excellent thermal and mechanical properties, and ability to be chemically modified to suit various applications. Thus far, cellulose has typically been incorporated in additive manufacturing applications as a substrate, filler, or reinforcement for other materials. However, due to its versatility and desirable properties, the exploration of all-cellulose 3D printing materials and associated methodologies is increasing. This review will discuss the progress and status of all-cellulose 3D printing approaches, associated challenges, and their potential as a key player in a more sustainable industrial future.

The recently explored synergistic combination of graphene-based materials and deep eutectic solvents (DESs) is opening novel and effective avenues for developing sensing devices with optimized features. In more detail, remarkable potential in terms of simplicity, sustainability, and cost-effectiveness have been demonstrated for sensors, resulting in the creation of hybrid devices with enhanced signal-to-noise ratio, linearity, and selectivity. Therefore, this review aims to provide a comprehensive overview of the currently available scientific literature discussing investigations and applications of sensors that integrate graphene-based materials and deep eutectic solvents, with an outlook for the most promising developments of this approach.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

With the development of bioinspired green solutions for sustainable construction over the past two decades, bio-cementation, which exploits the naturally occurring phenomenon of calcium carbonate precipitation in different environments, has drawn a lot of attention in both building construction and soil stabilization. Various types of microorganisms, along with specific enzymes derived from these microorganisms, have been utilized to harness the benefits of bio-cementation. Different application methods for incorporating this mechanism into the production process of the construction material, as well as a variety of experimental techniques for characterizing the outcomes of bio-cementation, have been developed and tested. Despite the success of bio-cementation as a sustainable method to construction has been demonstrated in a significant body of literature at the laboratory scale, the expansion of this strategy to construction sites and field application remains a pending subject. The issue may be attributed to two primary challenges. Firstly, the complexity of the bio-cementation phenomenon is influenced by a variety of factors. Secondly, the extensive body of literature examines various types of microorganisms under different conditions, leading to a wide range of outcomes. Hence, this study aims to examine the recent advancements in utilizing the most commonly employed microorganism, Sporosarcina Pasteurii, to emphasize the significance of influential factors identified in the literature, discuss the findings that have been brought to light, and outline future research directions toward scaling up the process.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

Productivity has been modest in construction due to many reasons, especially project-specific operations and fragmentation. The main aim of this research is to map the challenges towards industrialization in construction through a comparative study of the manufacturing industry. An inductive approach and a qualitative method are followed by applying semi-structured inter-views, and node-based thematic analysis. The key elements of industrialization in mature man-ufacturing companies are benchmarked. The findings indicate a specific order of steps for indus-trialization in construction. Data and information management with achieved systematization have been sources of productivity in manufacturing companies. However, the systematization starts from the offering, construction companies need to define their offering, that is the products, and define their respective data. Only accurate and good quality data on products enables the systematization of order delivery processes, which are the engine for a company’s success or failure. Continuous efficiency improvement is only possible with systematized processes and respective data related to the processes. The originality involves clarifying the industrialization of construction companies via products, respective data, and processes considering industrialized manufacturing companies.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

The use of New-age (Nano) Modified Emulsions (NME) for the stabilisation of marginal materials for use in the upper-pavement layers of roads have been proven in laboratories, through Accelerated Pavement Tests (APT) and in practice. In addition, material design methods have been developed based on the scientific analysis of granular material mineralogy and the chemical interaction with the binder to design a material compatible NME stabilising agent for naturally available (often marginal) materials. However, the introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology enables the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In practice, few road construction projects are without any problems. The introduction of new-technologies obviously makes it an easy target to blame for any non-related problem that may arise during construction. This article aims to assist in pre-empting, recognising, preventing and resolving material or non-material related construction problems through the correct identification of the cause of the problem and recommending the best, most cost-effective way to correct any deficiencies on site.

Large-span post-tensioned (PT) beams play a crucial role in maximizing the benefits of post-tensioning techniques. Bonded and unbonded systems are prevalent, with the latter being more widespread in the United States. While bonded systems are advantageous for creating long spans when multiple tendons are grouped in ducts, limited literature exists on their demolition. In a case study, this paper addresses the unique challenge of demolishing large-span bonded post-tensioned beams due to a building's functional change. Emphasizing insights for engineers, it explores the use of cutting and dismantling methods, considering the presence of prestressed cables. The demolition process is distinctive due to the presence of numerous pre-stressed cables along the beams, necessitating a specialized and cautious cutting approach. This is accomplished through the use of a drilling technique that selectively distresses the tendons, ensuring they are not all affected simultaneously. An intriguing observation discussed in this paper pertains to the occurrence of horizontal cracks accompanied by loud sounds following the drilling process, offering insights from the design perspective of PT systems. The paper details an innovative method for safely demolishing large-span bonded PT beams, using ground-penetrating radar and computer models to navigate structural complexities and ensure nearby structures' safety.

Background: Dental education blends theoretical and practical training to prepare students for independent patient care. This study examines the confidence levels of dental students in Umeå regarding independent performance of general dentistry tasks, and whether this confidence changes after clinical training. Methods: Surveys were conducted before and after a summer clinical internship, with s tudents rating their comfort levels on a scale from 0 to 10 for various procedures. Results: Results from 64 initial surveys and 54 follow-up surveys showed no significant difference in confidence before and after the internship. However, confidence levels varied based on whether students had practiced specific tasks during the internship. Students felt least confident in managing acute dental trauma and treating cavities in young children, while they were most confident in tasks like obtaining radiographic surveys and debriding periodontally compromised dentition. Tooth extraction and dental fillings were the most practiced procedures during the internship. Conclusions: The study concludes that the internship between the ninth and tenth semesters does not notably boost students' confidence in specific dental procedures, possibly due to the short duration of the training. Further exploration, including input from clinical supervisors, is suggested to optimize clinical training in dental education.