A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

The decarbonization of the electricity grid as one among the actions to reduce fossil fuel emissions, and thus their impact on global warming in the future, will be achieved mainly via the integration and widespread diffusion of renewable power sources. This is going to be supported also by the shift from the paradigm production-transmission-distribution, where electricity production oversees large-size power plants, to renewable-based distributed/diffused production, where electricity is generated very close or even by the same (group of) user(s) (or prosumers in the latter case). The number of mid-/small-size installations based on renewable energy technologies will therefore increase substantially, and the related renewable generation will be dominant against that from large-size power plants. Unfortunately, this will reduce the reliability of the grid very likely, unless appropriate countermeasures are taken/implemented, hopefully at the same time the paradigm shift is being achieved. To this aim, it is important to identify the anomalies and main fault causes that might determine in renewable-based power systems. This paper surveys the current state-of-the-art on anomalies and faults affecting wind-PV-storage hybrid power systems, i.e., the main renewable technology ensemble that will establish the future grid, and highlights possible research directions that may help to fill the literature gaps.

This study investigates the impact of intellectual capital on the sustainable performance of banks in Saudi Arabia, focusing on the period from 2012 to 2022. Utilizing data from ten major Saudi banks, the research examines how different components of intellectual capital—Human Capital Efficiency (HCE), Structural Capital Efficiency (SCE), and Capital Employed Efficiency (CEE)—influence key financial performance indicators such as Return on Equity (ROE) and Net Profit Margin (NPM). The study is grounded in the resource-based view of the firm, which suggests that a firm’s internal resources can provide a sustainable competitive advantage. The analysis employs panel data techniques, including fixed and random effects models, to assess the relationships between intellectual capital components and bank performance while controlling for variables like bank size, financial leverage, GDP growth, inflation, and the impact of the COVID-19 pandemic. The findings reveal that intellectual capital significantly enhances bank performance in Saudi Arabia, with human capital efficiency showing the most decisive influence on ROE and NPM. Structural capital and capital employed efficiency also contribute positively but vary in their impact on different performance measures. This research contributes to the theoretical and practical understanding of the role of intellectual capital in promoting sustainable banking practices. It underscores the importance of strategic management of intellectual capital in enhancing financial performance and achieving sustainability goals, particularly in the context of Saudi Arabia's Vision 2030. The study's insights are relevant for bank managers and policymakers who leverage intellectual capital for economic diversification and sustainable development.

This study examines the relationship between entrepreneurship and sustainable devel-opment in Saudi Arabia from 2006 to 2022, focusing on the economic, social, and en-vironmental dimensions. Using the Autoregressive Distributed Lag (ARDL) model, the research investigates both short-run and long-run dynamics to understand how entre-preneurial activities influence sustainable development within the framework of Saudi Arabia's Vision 2030 initiative. The findings indicate that entrepreneurship significantly contributes to economic growth through job creation and innovation, thereby aiding in the diversification of the economy away from oil dependency. Socially, entrepreneurial ini-tiatives have a positive impact on gender equality and social inclusion by empowering women and integrating youth into the labour market. Environmentally, entrepreneurship helps reduce carbon emissions and promotes sustainable business practices. Despite these positive outcomes, challenges such as regulatory barriers, limited access to finance, and the need for a supportive entrepreneurial ecosystem remain. Recommendations include enhancing entrepreneurial education, providing financial incentives, and streamlining regulatory processes to better support start-ups and SMEs. The study highlights the ne-cessity of addressing these challenges to fully realize the potential of entrepreneurship for sustainable development in Saudi Arabia. By providing empirical evidence on the sig-nificant role of entrepreneurship in driving sustainable development, this research offers actionable insights for policymakers aiming to foster a more resilient and diversified economy in line with Vision 2030. .

Water scarcity, particularly in arid and semi-arid regions, poses a significant challenge to crop production, with drought being a prevalent factor limiting grain production globally. Enhancing agricultural water use efficiency is crucial for managing water resources effectively in these areas. Water resource management involves planning, developing, distributing, and optimizing the use of water resources. Water use efficiency management is also essential for crop growth in arid regions. Various agronomic and irrigation strategies can improve crop water use efficiency and drought tolerance. The primary goal of these strategies is to maximize irrigation efficiencies by applying the precise amount of water needed to restore soil moisture to the desired level. These sustainable practices not only reduce the cost of water and labor for farmers through reduced irrigation but also optimize the use of soil moisture storage. This review paper explores practical techniques to improve water use efficiency, highlighting the role of nutrients in enhancing water use efficiency in crop plants.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

Vernonia mespilifolia is widely used in folk medicine in the Eastern Cape Province, South Africa. The aim of this study was to evaluate the biological activity of the acetone, aqueous and ethanol extracts of Vernonia mespilifolia using brine shrimp hatchability and lethality assay. The result showed hatching success in this order: aqueous extract (48.6%) > acetone extract (38.2%) > ethanol extract (26.8%). The LC₅₀ of the lethality assay were in this order: acetone extract (67.8 µg/mL) > aqueous extract (132 µg/mL) > ethanol extract (383 µg/mL). According to Meyer’s toxicity index (using brine shrimps), LC₅₀ < 1000 µg/ mL is toxic. Therefore, the results of the three solvent extracts could be said to be toxic as do have LC₅₀ < 1000 µg/ mL. However, the toxicity of the crude extracts could suggest or confer some antitumor properties, hence further in vitro, in vivo and antitumour assays are recommended to further substantiate these claims.

The effects of climate change health impacts on urban health care systems and vulnerable populations are a researched topic with foundations on urban risk management, urban health methodologies, and sustainable urbanization. As climate change is a dynamic and transformative global issue the gap between adaptation and mitigation efforts and urban planning relies, among other things, in the limitations of previous studies of risk management structures tailored to the existing strategy to calculate the uncertainties and predict their influence on urban systems and subsystems. Moreover, as climate and health is a well-researched issue, it is also complex as the methodologies and strategic approach to minimize health risks of climate change is intrinsically contingent to risk methodologies and policy-making processes that are efficient with support of knowledge-based information. This paper emphasis the need for focusing on urban health risk management methods that serves to identify potential opportunities, and then manage and take action to prevent adverse health effects. It also emphasizes the probability of events and their consequences, which are measurable both qualitatively and quantitatively.

Digital transformation provides new drivers for economic performance growth in enterprises, but can it further improve ESG performance and support sustainable development? Based on the perspective of resources and capabilities, this paper uses the relevant data of 1588 listed companies in strategic emerging industries from 2011 to 2021 to study the differential impact of digital transformation on enterprise ESG performance, and further tests the mediating role of absorptive capacity and the moderating role of regional digital level. The research results indicate that: firstly, digital transformation of enterprises can positively promote the improvement of ESG performance; Secondly, there are significant differences in the impact of digital transformation on the ESG performance of enterprises in terms of property rights and industry characteristics. The ESG performance of state-owned enterprises and high-end equipment manufacturing enterprises is more sensitive to digital transformation; Thirdly, absorptive capacity plays a mediating role between digital transformation and corporate ESG performance; Fourthly, the positive regulation of regional digital level promotes the ESG performance of enterprises through digital transformation. The research conclusion is based on a digital perspective, providing relevant insights for improving the ESG performance of strategic emerging industry enterprises and expanding their ESG development paths.

CAMx-LPiG (Comprehensive Air Quality Model with Extensions – Linear Plume in Grid) is an online hybrid model, based on the Chemistry and Transport Model (CTM) CAMx, that includes a sub-grid scale module to simulate the dispersion of linear road traffic emissions, called LPiG. LPiG is a plume in grid module specifically developed by extending the capabilities of the Lagrangian puff sub-grid model available in CAMx. The online integration of the local scale model within the Eulerian CTM allows for a multiscale simulation of air quality from the regional scale to the urban scale, preserving a coherent description of the chemical state of the atmosphere at all spatial scales and avoiding any double counting of the emissions simulated by the sub-grid module. In this work the model is presented and evaluated against measured NO2 concentrations for the city of Milan for the month of January 2017. The model is able to introduce road traffic induced gradient in NO2 concentration at sub-grid resolution. Moreover, CAMx-LPiG is shown to reduce the bias compared to CAMx stand-alone simulations.

Probiotics are becoming more and more popular in the growing of fin and shellfish because these species are consumed worldwide and because different techniques are employed to maximize the productivity and efficiency of fin and shellfish. Probiotic Bacillus is one of the many types of probiotics that are used, but it stands out due to its superior qualities. For instance, because of its ability to sporulate, it can survive in harsh environments, produce antimicrobial substances, and is safe to feed to fish. The different species of Bacillus used in the farming of fin and shell fish were discussed in this review, along with the benefits of using Bacillus spp. as a good substitute in sustainable aquaculture to improve feed utilization, immune system response, stress adaptation, resistance to infectious diseases, tissue preservation integrity, and water quality. Additionally, we discussed the possible risks to safety that Bacillus poses when raising these significant species. For the purpose of future research and development regarding Bacillus application in aquaculture, a summary of the findings of recent studies about the advantages of applying Bacillus to enhance fin and shellfish aquatic animal culture has been provided.

Long term Precipitation and temperature variations are one of the main determinants of climate variability of one’s area. The aim of this study is to determine trends variation in climatic elements of temperature and precipitation in the southern zone of Tigray regional state, Ethiopia. The station is assumed for the study of climatic records over southern zone of the region in detection for probable trends. The daily, monthly and annual precipitation totals and temperature observed at korem meteorological station were used for the period of 1981-2010 for Precipitation and 1985 – 2010 for minimum and maximum temperature. Summary of descriptive statistics and Mann Kendall test methods were employed for the observed data analysis to demonstrate any existence of possible trends. The main findings of the study indicated that the mean and maximum temperature had a general increasing trend; however, minimum temperature showed decreasing trend. In general annual temperature from 1985 – 2010 of the area showed a warming trend. Moreover analysis of the 30 years (1981-2010) annual precipitation showed a coefficient of variation ranging from 33.77 – 233 %. It indicated that the precipitation dissemination is not normal with large year to year variances.

Smart manufacturing encompasses a category of manufacturing that employs computer-integrated capabilities and technologies to enhance supply chain optimization, production efficiency, and recyclability. Yet limited studies have been conducted to optimize these prospects from the perspective of low resource countries where such innovative studies have not been adequately explored. This paper aims to examine the implications of smart manufacturing practices (Smart Procurement, Smart Supply Chain, Smart Production Planning and Control, Automation and Industrial Robot, and Supply Chain Configuration) on pro-environmental behaviour and develop a baseline moderated mediation model to explain the relationship between smart manufacturing and pro-environmental behaviour with a role of green dynamic capability, and environmental orientation. This study is anchored on quantitative research approach, deductive reasoning, and explanatory design. Cross – sectional survey data have been obtained from 382 manufacturing companies in Ghana. Our hypotheses have been tested using Structural Equation Modelling and SMART-PLS version 3.8.9. The study has revealed that smart manufacturing practices significantly and positively relate to pro-environmental behaviour. Moreover, green dynamic capability and environmental orientation moderate the relationship between smart manufacturing and pro-environmental behaviour. The implications of the study include the emergence of a baseline model to guide policymakers, practitioners, and academicians to explain the relationship between smart manufacturing and sustainable manufacturing in the context of developing countries. Again, the social implication of the study includes the realisation of decent job and economic growth, responsible consumption and production as well as actions taken to combat climate change.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

Our study reviews the significance of archaeological parks in the tourism sector, with a specific focus on how digital presence and visitor feedback impact their cultural and touristic appeal. Utilizing statistical analyses such as regression and cluster analysis on data sourced from both Hungarian and Western European parks, the research scrutinizes TripAdvisor and Google ratings, alongside the volume of photographs and reviews. The findings highlight a modest correlation between digital visibility and overall visitor ratings, underscoring the complex relationship between online engagement and the quality of visitor experience. Notably, the cluster analysis identified two distinct groups, signifying diverse levels of visitor engagement and digital visibility across the parks. The conclusions drawn advocate for a comprehensive strategy to enhance visitor experiences, emphasizing the integration of digital engagement with the promotion of the parks cultural and historical values. By exploring the influence of digital presence on the appeal of archaeological parks, our study sheds light on the evolving interface between urban studies and digital heritage, highlighting how digital tools and online platforms are becoming increasingly integral in shaping the perceptions and experiences of urban cultural sites.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

This paper explores how the sustainable investment impacts financial returns and economic development in of Asia Pacific and North America, utilizing real data empirically. In academia and industrial field, it is polemical that indeed, the sustainable behavior has economic returns. In order to clarify that, we tested hypotheses with an analysis of seven stock markets, accounting of rates such as ROI, ROIC, and ROA in eleven companies, and GDP/GNI per capita. The results indicate that both financial return and economic development are positively germane to the sustainable investment. Besides, the variance of sustainability to economic development exists, depending on GDP per capita between two regions. We conclude, concerning the sustainability, by corroborating micro perspective for corporate level and macro perspective of economic development in the private and public sector. This research consequence will be interested in both practitioners and researchers in the measurement of sustainability performance

Among earth’s microbial populations are the genes, functional capacities, generational memory and sentient cognition that enable microorganisms to adapt and thrive in the full range of ecological conditions found on planet earth. In prior sequential publications, we considered fundamental properties (e.g., use of and responses to sound, light, vibrations) and features of microorganisms that cause them to be critical co-partners of human and other holobionts as well as the potential benefits for humanity that can be gained by fully applying quantum-related and novel capacities of microbial life. In this narrative review we: 1) discuss key concepts concerning a microbially-enhanced and sustainable future, and 2) focus on electric- and magnetic- based features of microorganisms that make them pivotal for myriad benefits ranging from beyond pharma-based health and wellness to free- and/or renewable energy and restorative agriculture to improved human networking. While the benefits are many, the risks posed by hazardous electric or magnetic field exposures to both holobionts and microbial communities are significant. This review concludes that microbes and their remarkable capacities offer both humanity and the planet a much brighter future if we reverse the demonization of microbes and wanton microbiome degradation that has predominated much of the past century.

The present study analyzes students' weather-related hazard and risk literacy in Greece, a climate change hotspot region in the Eastern Mediterranean. In this context, we examine the students' level in two core literacy variables, namely knowledge and competency. In addition, we explore how knowledge, attitudes and socio-demographic variables influence students' competencies related to weather and climate risk assessment and adaptability. A questionnaire-based survey was conducted on 474 students aged 12-16. The regression results showed that knowledge significantly affects the level of competency. Self-belief and confidence in science were the most influential among the attitudinal variables. We conclude by discussing educational and behavioural issues highlighted as essential to address with targeted policies and measures in formal education complemented by non-formal educational activities.

This bibliographic study addresses key aspects related to fishing, product safety, and climate change in the Adriatic Sea region. The examination of product safety focuses on the assessment of contaminants originating from human activities such as industry, mining, agriculture, and household waste disposal. The contamination of the aquatic environment has emerged as a pressing global concern, extending to the Adriatic subbasin. Aquatic organisms, including fish, are prone to accumulating pollutants directly from polluted water sources and indirectly through the food web. The bio-accumulation of potentially hazardous substances, particularly heavy metals, pesticides, PCBs, PAHs, and antibiotic resistance in aquatic organisms, poses a significant threat to human health. Climate change effects will deplete our seafood supply in terms of quantity and safety owing to negative consequences such as higher levels of pollution, parasites, viruses, infections, acidification, and toxicities such as shellfish poisoning. Global food safety strategies should be developed to reduce greenhouse gas emissions and promote environmentally friendly technology, which indirectly affects seafood quality and microbiological safety, especially for Adriatic Sea, which is part of the Mediterranean Sea, characterized by the most polluted waters in the world.

Polar stratospheric clouds (PSCs) form in polar regions typically between 15 and 25 km, when the local temperature is sufficiently low. PSCs play an important role in the ozone chemistry and the dehydration and denitrification of the stratosphere. Lidars with a depolarization channel may be used to detect and classify different classes of PSCs. The main PSC classes are water ice, nitric acid trihydrate (NAT) and supercooled ternary solutions (STS), the latter being liquid droplets consisting of water, nitric acid and sulphuric acid. PSCs have been observed at the lidar observatory at Concordia Station from 2014 on. The harsh environmental conditions at Concordia during winter render successful lidar operation difficult. In order to facilitate the operation of the observatory several measures have been put in place to achieve an almost complete remote control of the system. PSC occurrence is strongly correlated with local temperatures and is affected by dynamics, as the PSC coverage during the observation season shows.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

Lean body mass (LBM) is correlated with powerlifting performance in athletes competing in different bodyweight classes. However, it remains unknown whether changes in LBM are correlated with performance changes in powerlifters preparing for a competition. Aim of the study was to investigate the changes in LBM and performance in powerlifters preparing for a competition. Eight male powerlifters (age 31.7±9.8years, height 1.77±0.06m, weight 99.2±14.6kg) and three female powerlifters (age 32.7±16.3years, height 1.54±0.06m, weight 66.6±20.9kg), participated in the study. Athletes followed individualized periodized training programs for 12 weeks aiming to maximize their performance for the national championship. Maximum strength (1-RM) in squat, bench press, and deadlift, body composition, grip strength, anaerobic power, quadriceps’ cross sectional area and vastus lateralis muscle architecture were measured before and after the training period. Significant increases were found after the training period in squat (5.8±7.0%, P

This study introduces numerical advancements in an alternative design for the SPS Beam Dump Facility (BDF) at CERN. The design envisions a high-power operation target made of flowing liquid lead. The BDF is a proposed versatile facility at CERN, intended for both beam-dump-like and fixed-target experiments. The target behavior is assessed, assuming a proton beam with a momentum of 400 GeV/c, a pulse frequency of 1/7.2 Hz, and an average beam power of 355 kW. An evaluation is conducted using various Computational Fluid Dynamics (CFD) codes to analyze the behavior of liquid lead and to predict the thermal stress on the target vessel induced by the pulsed heat source generated by the charged particle beam. The comparison increases the reliability of the results, investigating the dependencies on the CFD modeling approach. The beam is modeled as a volumetric heat source with data coming from beam-lead interaction simulations provided by CERN and obtained with the Monte-Carlo code FLUKA. The velocity field and stress profiles are utilized to enhance the design of the lead loop and verify its viability and safety when operated with a liquid metal target.

The sustainable development of resource-based cities has long been a focal point for both governmental policies and academic research. A wealth of academic literature identifies the 'resource curse' as a critical barrier to sustainable development in these urban areas. Despite extensive studies, a consensus on effective strategies to circumvent or resolve this challenge remains elusive. Recent empirical data reveals a noticeable pattern of economic growth differentiation in China's resource-based cities. Why do some resource-based cities experience economic decline while others achieve sustainable economic growth? Therefore, this paper analyzes the reasons for the divergence of economic growth in resource cities from the perspective of heterogeneity. The results of the study show that the phenomenon of the resource curse is conditional, and the heterogeneity of demo-graphic changes, geographic location and institutional environment has a significant impact on the economic growth of resource cities. These factors are investigated to elucidate the observed diversification and heterogeneity in the economic growth of resource-based cities. Building upon this analysis, the paper proposes a framework for differentiated sustainable development pathways tailored to the unique contexts of these cities. This approach not only contributes to the current understanding of the 'resource curse' but also offers novel insights for future research aiming to adopt a more nuanced and context-specific perspective in examining sustainable urban development.

Early childhood may be a stressful period for families with a significant impact on parents’ mental health and the child’s healthy development. The goal of the SKKIPPI cohort study was to assess the occurrence and determinants of psychosocial stress and mental health disorders in parents as well as in their offspring in early childhood in three German regions. Based on random samples from three residents' registration offices, parents with infants up to 12 months of age at the time of sampling, were invited to participate in the study. A screening online questionnaire was newly developed, available in four languages, to assess common psy-chosocial stressors and mental health problems of parents with small children. The study enrolled 4,984 mothers and 962 fathers. The most common potential psychosocial stressors at baseline were professional problems (mothers 22%, fathers 33%), lack of social sup-port (20%, 14%), and severe, negative experiences in childhood (22%, 16%). Obses-sive-compulsive thoughts (21%, 16%), depressive (9%, 9%) and anxiety symptoms (11%, 7%) were the most frequently reported mental health problems by both parents. Regulatory prob-lems of the child were reported by between 1.5% and 5.1% of parents. The SKKIPPI study showed that a substantial proportion of parents are burdened by psychoso-cial problems and suffer from mental health problems in the first years after birth. Early pre-ventive and low-threshold support measures should be available in the health and social care system. The newly developed questionnaire can be used to screen in the relevant populations in order to avoid disturbances in the mother-child attachment.

Semi-Interlocking Masonry (SIM) represents an innovative building system developed at the Centre for Infrastructure Performance and Reliability at The University of Newcastle, Australia. This system employs a unique approach to interlocking mortar-less engineered masonry panels constructed from SIM units. These units are designed to offer substantial energy dissipation capacity, primarily attributed to the friction occurring on the sliding bed joints between the units within the panel during seismic events. The primary aim of this study is to evaluate the viability of incorporating semi-interlocking masonry as infill panels in the construction of multi-storey buildings across diverse geographical locations with varying seismic conditions in Australia. To assess the feasibility of SIM panels in different conditions (according to Australian Standard AS1170) in Australia, a comprehensive analysis using Strand7 is conducted on a three-storey structure incorporating traditional masonry infill panels and SIM panels. The comparison of displacement and base shear capacities is carried out in response to seismic events across various scenarios in different locations within Australia. The insights gained from this comparative analysis contribute valuable information regarding the viability of implementing SIM as a contemporary construction material.

Starting from the fact that one of the global control strategies of the Permanent Magnet Synchronous Motor (PMSM), namely the Direct Torque Control (DTC) type control strategy, is characterised by the fact that the inner flux and torque control loop usually uses hysteresis ON-OFF type controllers and the oscillations introduced by them have to be cancelled out by the outer speed loop controller (which is usually a PI speed controller and whose performance is good around the global operating points and for relatively small variations of the external parameters and disturbances caused in particular by the load torque variation), while retaining the advantages of the DTC strategy, this paper presents the improvement of the performance of the PMSM sensorless control system using Proportional Integrator (PI), PI Equilibrium Optimizer Algorithm (EOA), Fractional Order (FO) PI, Tilt Integral Derivative (TID) and FO Lead-Lag for constant flux, and Sliding Mode Control (SMC) and FOSMC for variable flux. The performance indicators of the control system are the usual ones: response time, settling time, overshoot, steady-state error and speed ripple, plus another one given by the fractal dimension (FD) of the PMSM rotor speed signal, and the hypothesis that the FD of the controlled signal is higher when the control system provides better performance is verified. The paper also presents the basic equations of the PMSM, based on which the synthesis of integer and fractional controllers, the synthesis of an observer for estimating the PMSM rotor speed, electromagnetic torque and stator flux are presented. The comparison of the performance of the proposed control systems and the demonstration of the parametric robustness are performed by numerical simulations in Matlab/Simulink using Simscape Electrical and Fractional Order Modelling and Control (FOMCON). Real-time control based on an embedded system using a TMS320F28379D controller demonstrates the good performance of the PMSM sensorless control system based on the DTC strategy in a complete hardware-in-the-loop (HIL) implementation.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

The tourism economy plays an essential role in supporting and driving tourism development. Therefore, studying its resilience is crucial for promoting sustainable and high-quality tourism development. Based on the core essentials of economic toughness, this paper constructs the tourism economic toughness evaluation index system, uses the entropy weight TOPSIS method to measure the tourism economic toughness of 10 counties and cities in the Yili River Valley in 2010-2019, analyzes its spatio-temporal evolution characteristics through the standard deviation ellipse, the traditional Markov chain, and the spatial Markov chain, and uses the grey correlation analysis method to analyze the driving factors of the tourism economic toughness. The results show that: (1) the economic resilience of tourism in the Yili River Valley shows a "W"-shaped time-series dynamic development trend with an average index of 0.28394, in which it experienced a decline from 0.28 to 0.27 during 2012-2013 and 2015-2016; (2) Spatial Pattern: The Yili River Valley tourism economic resilience is characterized by a clear uneven spatial distribution. The city of Yining, representing the northwestern region, exhibits a high level of resilience, while the southwestern region, endowed with rich tourism resources, demonstrates a medium level of resilience. Conversely, the central to southeastern counties and cities, such as ChabuchaerXibo Autonomous County and other counties and cities, are characterized by a lack of developed tourism facilities, which has resulted in a lower level of resilience and a weak development situation; (3) In terms of spatial and temporal evolution, the standard deviation ellipse is stabilized year by year pointing to "northwest-southeast", the clustering tendency is gradually enhanced, and five tourism economic resilience convergence clubs are identified, whose internal transition probability is significantly affected by spatial location, and which show obvious stability and neighborhood effects; (4) Regarding the driving factors, the impact of each driving factor on the resilience of the tourism economy reaches the statistical significance threshold of 0.77 or above. Among them, the number of employees in the tertiary industry, especially the input of high-quality talents in the tourism industry, plays a key role in improving the quality of tourism services and strengthening the industry's ability to withstand risks and development potential.

The seed habit is the most complex and successful method of sexual reproduction in vascular plants. It represents a remarkable moment in the evolution of plants that afterwards spread on land. In particular, seed size had a pivotal role as for evolutionary success and agronomic trait, especially in the field of crop domestication. Given that crop seeds constitute one of the primary products for consumption, it follows that seed size represents a fundamental determinant of crop yield. This adaptative feature is strictly controlled by genetic traits from both maternal and zygotic tissues, although seed development and growth are also affected by environmental cues. Despite being a highly exploited topic for both basic and applied research, there are still many issues to be elucidated as for developmental biology as well as for agronomic science. This review addresses a number of open questions related to cues that influence seed growth and size, and how developmental processes are influenced by them. Besides, new insights on the genetic-molecular control of this adaptive trait are presented.

In this work, zinc oxide (ZnO)/ granular activated carbon (GAC) composites at different ZnO concentration (0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC) were prepared by an in-situ hydrothermal method and demonstrated synergistic photocatalytic degradation and ad-sorption of Rhodamine B (RhB). The thermal stability, morphological structure, elemental com-position, crystallographic structure, and textural properties of developed catalysts were charac-terized by thermal gravimetric analysis (TGA/DTG), scanning electron microscopy equipped with energy dispersive-x-ray (SEM-EDS), x-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) analysis. Successful loading of ZnO onto GAC was confirmed by SEM-EDS and XRD analysis. The BET surface areas of GAC, 0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC were 474 m2/g, 450 m2/g, 453 m2/g, and 421 m2/g, respectively. The decrease in GAC could be attributed to the successful loading of ZnO on the GAC surface. Notably, 0.5M-ZnO@GAC exhibited the best photocatalytic degradation efficiency of 82% and 97% under UV-A and UV-C light over 120 min, attributed to improved crystallinity and visible light absorption. The photocatalytic degradation parameters revealed that lowering the RhB concentration, raising the catalyst dosage and pH be-yond the point of zero charge (PZC) would favor the RhB degradation. Photocatalytic reusability was demonstrated over 5 cycles. Scavenger tests revealed that the hydroxyl radicals (•OH), su-peroxide radicals (O2−•), and photoinduced hole (h+) radicals play a major role during the RhB degradation process. Based on the TOC results, the RhB mineralization efficiency of 79.1% was achieved by 0.5M-ZnO@GAC. Additionally, GAC exhibited a strong adsorptive performance towards RhB with adsorption capacity and RhB removal of 487.1 mg/g and 99.5% achieved within 90 min equilibrium time. The adsorption characteristics were best described by pseu-do-second-order kinetics, suggesting chemical adsorption. This research offers a new strategy for the development of effective photocatalyst materials with potential for wider wastewater treat-ment applications.

This research investigates the intricate dynamics between intellectual Capital (VAIC) and the stability of banks in the evolving context of Saudi Arabia's banking sector. Against the backdrop of rapid economic reforms under Vision 2030 and the challenges imposed by the COVID-19 pan-demic, the research provides a nuanced analysis of how intellectual capital and intellectual capital's components—Human Capital Efficiency (HCE), Structural Capital Efficiency (SCE), and Capital Employed Efficiency (CEE)—affect the financial stability of Saudi banks. The research analyses a decade-long panel dataset from 2012 to 2022, utilizing both fixed effects and cross-section random effects models to discern the impact of intellectual capital on bank stability. The findings reveal a positive overall influence of intellectual capital on bank stability; however, individual compo-nents present a complex relationship, with CEE showing a positive association and HCE and SCE demonstrating unexpected negative correlations with bank stability. The research identifies lev-erage (LEV) as a significant factor negatively impacting stability. Operational efficiency (OPEF) and size (SIZE) also negatively affect stability. Surprisingly, macroeconomic indicators and bank size exhibit non-significant effects on bank stability. Similarly, the direct impact of the COVID-19 pandemic was found to be non-significant, suggesting a resilient banking environment or the presence of effective mitigating strategies. As Saudi Arabia continues its ambitious economic transformation, this research underscores the critical role of effectively managed intellectual capital in ensuring the banking sector's stability. It provides a foundation for ongoing research in this vital area.

The financial performance of local governments is closely related to the economic growth of a region. Strong financial performance provides a solid foundation for sustainable economic development. This study analyses the relationship between local government financial performance, capital expenditure, and sustainable economic growth in Banten Province. A quantitative approach was employed, using secondary data from Regional Revenue and Expenditure Budgets and economic growth statistics. Purposive sampling was utilised, and data analysis was conducted using Path Analysis. The findings reveal that several financial ratio variables significantly impact economic growth directly and indirectly through capital expenditure as a mediating variable. Directly, the independence ratio, effectiveness ratio, efficiency ratio, fiscal decentralisation ratio, dependency ratio, and capital expenditure significantly influence economic growth. The independence and effectiveness ratios have a positive impact, indicating that improvements in these variables directly foster economic growth. However, the efficiency and fiscal decentralisation ratios have a negative impact, suggesting that increases in these variables may reduce economic growth. Indirectly, through capital expenditure, the independence, effectiveness, dependency, and compatibility ratios significantly affect economic growth, with the independence ratio being the most dominant. Conversely, the fiscal decentralisation and efficiency ratios do not show significant indirect effects, indicating that capital expenditure is not an effective mediator for these variables.

The objective of this study was to determine how application with dolomitic limestone and grazing type (continuous or deferred) affect sheep grazing location and feed preference when the pasture growth rate is maximum. A 4ha field was divided into 4 plots: P1 and P2- without application of dolomitic limestone, continuous (CG) and deferred grazing (DG), respectively; P3 and P4- with application of dolomitic limestone, DG (1AUE), and CG (2.4 AUE), respectively. In DG, animals were placed and removed from the plots depending on the height of the pasture. In each plot, 12 georeferenced sampling points were identified. Throughout the pasture's vegetative cycle (autumn, winter, spring, and early summer) several measurements of pasture height and cut were carried out. From the beginning of March to the beginning of June, animal behavior was observed, by trained observers, through binoculars on six dates. Animals' activity grazing and location was recorded. The results show that: (i) the application of dolomitic limestone combined with CG provided higher values of pasture height; (ii) there were no significant differences in pasture quality between treatments; (iii) Deferred grazing led to 50% more sheep grazing days than continuous grazing; (iv) there were no significant differences in soil compaction between CG and DG; (v) the type of grazing and the treatment with dolomitic limestone did not seem to change the grazing pattern between treatments. This work contributes to understanding the relationships between different types of grazing in dryland pastures, with and without application of dolomitic limestone, and preferred grazing locations for sheep. This work could help agricultural managers make more informed decisions with the aim of promoting the sustainable intensification of livestock production in the Montado ecosystem.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

The intelligent elderly care model places new demands on the skills of aging caregivers. The identification and development of forward-thinking, high-potential nursing talent is essential for advancing the intelligent elderly care sector. Multi-benchmarking selection and competitive analysis is used to evaluate and identify nursing personnel in the rehabilitation treatment center of a hospital in Hefei City. Using proxy evaluation and democratic evaluation model, three types of benchmarks such as single item benchmark, individual benchmark and group benchmark were identified and selected, and the professional nursing team was constructed based on the evaluation results. Different from the traditional other-directed evaluation, multi-benchmarking selection and competitive analysis is self-directed evaluation, this method is more conducive to the identification of high-potential and digital nursing talents by intelligent elderly service organizations, and facilitates the formation of professional nursing teams with complementary strengths and cross-fertilization, so as to satisfy the diversified and multi-level needs of the elderly for intelligent elderly services.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

Despite the known benefits of precision agriculture, the adoption is challenging due to the cost of investment and the farm sizes. Therefore, profitability is an important aspect to consider. This study aimed to evaluate the net returns, profitability, and investment efficiencies of PA by different economic farm sizes. The study was based on data retrieved from FADN and Eurostat. The study examined four countries (Poland, Germany, France, and Romania) under field crop farming using an investment cost of €35 941 - €71 883, and a 20% and 15% reduction in the cost of crop protection and fertilizer usage respectively without compromising productivity. There is a positive relationship between the adoption of PA and farm returns for larger-scale farms. The result of the profitability and analysis of investment efficiency using NPV showed a positive value for economic farm sizes of €100 000 and above. Hence, it is not economically advisable that all farmers use PA technologies with the hope that they will be profitable but with public support (subsidies) more farms will be able to use PA and be profitable. Also, an opportunity to meet the goal of the European Union Green Deal of minimizing emissions that cause climate change.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

The West Pomeranian Anti-Crisis Package was an effective tool of the Voivodeship Executive Board of West Pomeranian self-government, which was used to combat and counteract and counteract the social and economic effects of the COVID-19 pandemic. The Anti-Crisis Package was prepared with a view to undertaking systemic, but also point-based measures in order to save and protect regional health care, entrepreneurs, the labour market, but also to use the existing social capital of non-governmental organizations involved in measures reducing the effects of the COVID-19 pandemic. The West Pomeranian Anti-Crisis Package, as evidenced not only by the financial outlays incurred, but also by the outcome of implementing measures achieved in 2020 and their continuation in 2021.

The concept of economic self-reliance, widely known by Thai people as the philosophy of sufficiency economy, has been widely promoted in rural Thai societies. By practicing this philosophy, it is expected that the citizens’ quality of life and local environments could be sustainably improved. This study aims to explore the contribution of the community practices of the sufficiency economy philosophy to rural villagers’ quality of life improvement, and to investigate potential factors that determine the trust of villagers in the philosophy. With the purpose to propose strategies which could enhance trust and promote villagers’ practices of the philosophy, the study investigated influences of three relevant factors on trust towards the philosophy. Those factors included factors related to cognitive-based trust, factors related to emotional-based trust, and factors related to demographic characteristics. Questionnaire surveys and in-depth interviews with community leaders and local villagers were conducted in the Ban Jamrung community, in Thailand’s Rayong province. The results of the statistical analysis revealed that the residents who applied the sufficiency economy philosophy in their daily lives experienced a relatively better quality of life. Additionally, it was found that trust in the philosophy could be predicted more by rational factors than by emotional factors. These findings could be utilized to develop strategies to maintain and enhance the trust of the people in the philosophy of sufficiency economy.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

Driven by the growing interest of the scientific community and the proliferation of research in this field, cranial implants have seen significant advancements in recent years regarding design techniques, structural optimisation, appropriate material selection and fixation system method. Custom implants not only enhance aesthetics and functionality but are also crucial for achieving proper biological integration and optimal blood irrigation, critical aspects in bone regeneration and tissue health. This research aims to optimize the properties of implants designed from triply periodic minimal surface structures. The gyroid architecture is employed for its balance between mechanical and biological properties. Experimental samples were designed varying three parameters of the surface model: cell size, isovalue and shape factor. Computational simulation tools were used for determining the relationship between those parameters and the response variables: the surface area, permeability, porosity and Young modulus. These tools include computer aided design, finite element method and computational fluid dynamics. With the simulated values, the corresponding regression models were fitted. Using the NSGA-II, a multi-objective optimisation was carried out, finding the Pareto set which includes surface area and permeability as targets, and fulfil the constraints related with the porosity and Young modulus. From these non-dominated solutions, the most convenient for a given application was chosen, and an optimal implant was designed, from a patient computed tomography scan. An implant prototype was additively manufactured for validating the proposed approach.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

Green finance in the context of sustainable development sits within the broader discourse of environmental economics and sustainable finance. Their integration has become imperative in addressing global challenges, aiming to understand how financial mechanisms can be aligned with sustainability goals, investigating the role of green finance in promoting environmentally friendly investments and fostering sustainable development. This bibliometric analysis explores the evolution, trends, and challenges in green finance research. It examines 436 articles published between 2016 and 2024, revealing insights into influential publications, authors, journals, institutions, and countries engaged in green finance for sustainability. The study identifies China, the UK, and Pakistan as leaders in research output and citation impact. Furthermore, it highlights the interdisciplinary nature of green finance, reflected in diverse publication outlets spanning environmental, social, and economic domains. The analysis underscores the increasing global interest in green finance, as evidenced by the growing citation rates over time. Key findings include the pivotal role of green finance in energy efficiency, renewable energy development, and the promotion of sustainable economic growth. Overall, this research provides valuable insights for policymakers, researchers, and practitioners, emphasizing the importance of interdisciplinary collaboration and continued research efforts in advancing sustainable finance agendas.

The olive tree (Olea europaea L.) is an evergreen tree that occupies 19% of the woody crop area and is cultivated in 67 countries on five continents. The largest olive production is concentrated in the Mediterranean basin, where the olive tree has had an enormous economic, cultural and environmental impact since the 7th century BC. In the Mediterranean region, salinity stands out as one of the main abiotic stress factors significantly affecting agricultural production. Moreover, climate change is expected to lead to increased salinisation in this region, threatening olive productivity. Salt stress causes combined damage by osmotic stress and ionic toxicity, restricting olive growth and interfering with multiple metabolic processes. A large variability in salinity tolerance among olive cultivars has been described. This paper aims to synthesize information from the published literature on olive adaptations to salt stress and its importance in salinity tolerance. The morphological, physiological, biochemical, and molecular mechanisms of olive tolerance to salt stress are reviewed.

Considering the unquestionable role of education in economic development, it has an impact at a macroeconomic level—contributing to enhancing productivity and innovation, reducing poverty and promoting social cohesion—and at a personal level—ensuring the improvement of knowledge, skills and individual capabilities and promoting social values like empowerment and equality. Notably, quality education is recognized as one of the Sustainable Development Goals (SDGs), which, jointly with other behaviors and attitudes, could impact the development of societies in other fields like health and well-being, cultural preservation, environmental sustainability and even peace and stability—all of them also listed as SDGs. However, the capacity, or not, to reach higher levels of compliance with quality in education (SDG 4) varies from country to country, according to the 2023 Sustainable Development Report results. Thus, the present study used a fuzzy set qualitative comparative analysis to assess the conditions for attaining higher levels of quality education based on the different indicators used to measure SDG 4. The analysis will allow comparisons of results among different countries and provide information about the initiatives that could be relevant to increasing quality education worldwide and for policymakers.

The Covid-19 pandemic was a challenge for the whole world and it had major secondary effects on humans and environmental health. The viral infection induced, in many situations, secondary bacterial infections, especially enteric infections by destabilizing the balance of the gastrointestinal microbiota. The large-scale use of antibiotics and biocides both for curative and preventive purposes has determined an increase in bacterial resistance and at the same time the possibility of pathogenic microorganisms’ multiplication and their dissemination to natural environments. Wastewater is the main vector of faecal microorganisms that favour their dissemination into natural aquatic ecosystems. The present paper aimed to analyze the effect of Covid-19 pandemic on the microbiological quality of wastewater from sewage treatment plants in Romania and its impact on receiving rivers. In order to highlight different and important areas of Romania, 3 cities from the east, center and west were selected for a microbiological evaluation of their WWTPs influent and effluent between ante-Covid-19 and Covid-19 pandemic peak period, when the Covid-19 pandemic had a direct impact on WWTPs microbial composition. Our study showed a higher contamination with fecal bacteria linked to a higher Covid-19 incidence. The increased usage of pharmaceutical compounds, at their turn, increased the number of resistant bacteria reaching the environment via WWTP effluents.

Enterprises that seek for sustainable development should align economic interests with environmental and social requirements. It is not enough to take into account just these basics components. Technology plays a significant role in company activity. The aim of this article is to highlight the relationship between the dimensions characterising sustainability and to take a deeper look at the structure of the concept of sustainability so that to understand in more detail the completeness of the dimensions of sustainability. For achieving this aim is necessary through the analysis of researchers’ opinions to apply the logical assessment, systematisation, and comparison of information, selects the most important information describing the sustainability of technology, highlights the relationships between the technological aspect of sustainability and other sustainability dimensions, evaluates the technological processes of the corporate product in terms of sustainability, clarifies and presents arguments highlighting the importance of the technological aspect in sustainable business activity, rejects inappropriate arguments, identifies links between the arguments, and, basing on the information, proves and/or formulates anew some logical considerations to justify the full competency of the technological dimension in the sustainable development framework.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

Intermittent religious fasting increases a risk of hypo- and hyperglycemia in individuals with diabetes, but its impact in those without diabetes is poorly investigated. The study aim was to examine the effects of religious Bahá'í fasting (BF) on glycemic control and variability and compare these effects with time-restricted eating (TRE). In a three-arm randomized controlled trial, 16 subjects without diabetes were assigned to a BF, 16:8 TRE or control group. Continuous glucose monitoring and food intake documentation was conducted before and during the 19 days of intervention, and 24-hour mean glucose, glycemic variability indices, and glucotypes were assessed. BF and TRE groups, but not the control group, markedly reduced the daily eating window while maintaining macronutrient composition. Only the BF group decreased caloric intake (-677.8 ± 357.6 kcal, p=0.013), body weight (-1.92 ± 0.95 kg, p=0.011) and BMI (-0.65 ± 0.28 kg, p=0.006). Higher maximum glucose values were observed during BF in the within-group (+1.41 ± 1.04, p=0.039) and between-group comparison (BF vs. Control: p= 0.010 and TRE vs. BF: p= 0.022). However, there were no alterations of 24-hour mean glucose, intra- and inter-day glycemic variability indices, or glucotypes in any group. Proportions of time above and below range (70-180mg/dl) and HbA1c values remained unchanged. BF and TRE do not exhibit negative effects on glycemic control and variability in subjects without diabetes.

Global wastes accumulate at an accelerating rate especially food and slaughterhouse waste constituting a major proportion owing to inefficient management. The high protein concentration of fish waste and keratinaceous byproducts is hazardous, harbouring pathogens, and emitting toxins. Transforming proteinaceous waste into amino acids (AAs) reduces waste bulk and offers a smarter nutrient approach for agriculture. However, this resource remains underutilized triggering eco-system pollution, diseases spreading, and climate change. Currently, small quantities of proteinaceous waste are valorized as animal feed, fertilizer, and in medical, and biotechnological sectors, which cannot solve bulk waste accumulation further, natural AA sources in agriculture are less recognized meanwhile researchers focus on synthetic AAs. Introducing various plant-nutrient formulas enriching fish AA with keratinaceous waste hydrolysate has not been broadly discussed. With this novel approach, using proteinaceous waste resources in agriculture would solve environmental pollution while minimizing land degradation by synthetic fertilizer. In this review, we illustrate the potential and benefits of valorizing proteinaceous waste in bulk through bioconversion. More importantly, we spotlight the biocompatibility of natural AAs and propose an enrichment, to use the ultimate product as catalysts for crops. Consequently, this approach reduces hazardous waste while paving a paradigm change in agriculture.

This study explores the current landscape of social value (SV) research in the construction industry, analyzing global trends and identifying future research directions. Using bibliometric analysis, research published in Elsevier Scopus database from 2013 to 2023 was extracted using the keywords "social value" AND "construction industry." Results indicate a focus on social value indicators, socioeconomic impacts, project management, innovative practices, and cross-sector collaborations. The study also reveals a lack of attention to SV in African countries' construction sectors. By highlighting research areas and identifying gaps, this study contributes to academic literature, suggesting the need for guidelines, particularly in developing countries, and advocating for further research on SV in the built environment and strategies for global social value creation.

The adoption of environmental conservation agriculture (ECA) in Nepal is aligned with the country's goal to achieve carbon neutrality by 2045, as ECA practices have been proven to effectively reduce greenhouse gas emissions. Nepal's agricultural sector faces numerous challenges, including labor shortages, climate change impacts, and the necessity for environmentally friendly farming methods, making the adoption of ECA practices even more crucial. This paper thus explored farmer perspectives on the sustainability of ECA practices in Namobuddha municipality, Nepal, which is renowned as a leading hub of organic farming. A cross-sectional survey was conducted, together with key informant interviews and onsite observations. By analyzing various farmer perspectives, the study presents an analytical framework that highlights the economic, environmental, and social pillars of ECA's sustainability. The findings underscore the significance of economic viability for farmers, as damages to crops and farm products negatively drive their perception of ECA sustainability. Conversely, factors such as increased agriculture-related income, favorable prices, and sustainable productivity positively shape farmers' perceptions. In terms of environmental sustainability, farmers prioritize enhancing the local and global environment, viewing their farming methods as climate-smart and actively working towards reducing greenhouse gas emissions. The study emphasizes the importance of strategic communication to effectively convey the benefits of ECA to rural communities. Overall, this research contributes to filling the knowledge gap concerning farmers' perceptions of ECA sustainability. The insights gained from this study have the potential to inform policy decisions and promote the widespread adoption of environmentally friendly farming practices in Nepal.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

This paper analyzes the causal effect between domestic private investment, public investment, foreign direct investment and economic growth in Tanzania during the 1970-2014 period. The modified neo-classical growth model is used to estimate the ieffect of investment on economic growth. Also, the economic growth models based on Phetsavong and Ichihashi (2012) [1], and Le and Suruga (2005) [2]are used to estimate the crowding out effect of public investment on domestic private investment on one hand and foreign direct investment on the other hand. In the same way, the crowding out effect of foreign direct investment on domestic private investment is estimated. A correlation test is applied to check the correlation among independent variables, and the results show that there is very low correlation suggesting that multicollinearity is not a serious problem. Moreover, the diagnostic tests including RESET regression errors specification test, Breusch-Godfrey serial correlation LM test, Jacque-Bera-normality test and white heteroskedasticity test reveal that the model has no signs of misspecification and that, the residuals are serially uncorrelated, normally distributed and homoskedastic. Broadly, the empirical results show that the domestic private investment and foreign direct investment play an important role in economic growth in Tanzania. Besides, a revealed negative, albeit weak, association between public and private investment suggests that the positive effect of domestic private investment on economic growth becomes smaller when public investment-to-GDP ratio exceeds 8-10 percent. Similarly, foreign direct investment tends to marginally reduce the impact of domestic private investment on growth. These results suggest that public investment and foreign direct investment need to be considered carefully in order to avoid a reduced positive impact of domestic private investment on growth. Domestic saving may be promoted to encourage domestic investment for economic growth.

Callus induction (CI) is the critical trait for the transformation of desirable genes in plants. A genome-wide association study (GWAS) analysis was conducted on the rice germplasm of 110 diverse indica rice accessions. Three tissue culture media, including B5, MS, and N6, were used for CI in those rice panels. Seven quantitative trait loci (QTLs) on chromosomes 2, 6, 7, and 11 were found to confer a CI percentage in these three media. For the B5 medium, one QTL (qCI-B5-Chr6) was identified on the rice chromosome 6. For the MS medium, two QTLs were identified on the rice chromosomes 2 and 6 (qCI-MS-Chr2 and qCI-MS-Chr6, respectively). For the N6 medium, four QTLs were identified on the rice chromosomes 6, 7, and 11 (qCI-N6-Chr6.1, qCI-N6-Chr6.2, qCI-N6-Chr7, and qCI-N6-Chr11, respectively). Fifty-five genes were identified within the haplotype blocks corresponding to these QTLs. Thirty-one genes showed haplotypes associated with different CI in those media. The qCI-B5-Chr6 was located in the same region as the qCI-N6-Chr6.2. The caleosin-related family protein was identified in this region. Analysis of the gene-based haplotype reveals the association of this gene with different CI in both B5 and N6 media, suggesting that the gene may play a critical role in the CI mechanism. Moreover, several genes, including the beta-tubulin, the zinc finger proteins, the RNP-1 domain-containing protein, and the Lysophosphatidic acid acyltransferase, were associated with different CI in the N6 media. Results from this study provide insight into the potential QTLs and candidate genes for callus induction in rice that will fulfill the understanding of the physiological and biochemical processes involved in callus formation, which is an essential tool in the molecular breeding of rice.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The wellness economy has developed rapidly recently, particularly in wellness tourism. Wellness tourism transforms sustainable strategy through the availability of extended multi-actor engagement in service innovation to further the tourism experience. Therefore, when operating a wellness tourism destination, it is necessary to encourage multi-actor engagement in service innovation to achieve sustainable development. This paper introduces a mixed research method with the SWOT-AHP-QSPM, as it qualitatively analyzes the advantages, disadvantages, opportunities, and threats, constructs an evaluation index system, conducts quantitative analysis using the analytic hierarchy process, determines the index weight and weighted score, and calculate the sustainable development strategy, which is appropriate for wellness development of Chongqing Tea Mountain and Bamboo Forest National Forest Park. Purposive field surveys and personal interviews were conducted in Chongqing forest tourism destinations, involving 356 effective respondents. The research reveals that multi-actor engagement significantly enhances sustainable development. These findings bridge service innovation knowledge gaps and provide valuable insights for forest tourism destination management and sustainable policy strategies to elevate multi-actor engagement in forest sites.

Energy poverty in the Global South generally focuses on the lack of basic access to modern fuels and energy carriers. Impoverished people rely primarily on traditional biomass as a source of energy. This situation of basic resource deprivation, in which almost one third of the world's population lives, masks other relevant features of the problem. Current assessments of energy poverty in impoverished areas and the mitigation strategies being implemented derive from the development agenda and, with variations in detail and scope, highlight electricity connections and access to clean cooking fuels as guarantors of progress. However, a comprehensive understanding of energy poverty requires going beyond basic access, building on the interactions between the supply of energy sources and carriers, the provision of energy services and its impact on decent living conditions. Several studies in the last decade have attempted to construct an assessment framework centered on energy services to deal with these interactions. This work discusses the relevant dimensions in the framework (supply, services and impact in wellbeing), reviews the multidisciplinary work available in each aspect, presents a range of proposed taxonomies, and discusses the different issues. A detailed framework is proposed for the integrated assessment of the supply of energy carriers and energy equipment, the provision of relevant energy services, and the improvements obtained in living conditions.

The authors argue that despite significant numbers of foreign workers present in the Russian labor market Russia remains unattractive for highly skilled foreign workers. The economic crisis the country has faced since 2014 has resulted in a further outflow of foreign nationals from OECD countries. So Russia has to look for employees among newcomers from the former Soviet states, the majority of whom come from Central Asia. Russian politics with regard to immigration is characterized by the collision between “geopolitical” and domestic policy rationales. On one hand, seeking to maximize its influence in the post-Soviet space Russia provides preferential conditions of employment for citizens of partner countries in the framework of the Eurasian Economic Union. On the other hand, the Kremlin is afraid to liberalize its approach to immigration and the integration of immigrants through fear of losing popularity among the electorate. The second substantial feature of Russian immigration politics is an extreme level of securitization of migration issues. The government considers these issues primarily through a policing lens. One cannot claim that the Russian state does not take any steps to liberalize “migratory regulation”; however, the effect of these measures is being vastly reduced by new restrictions. In addition, liberally designed laws do not bring the expected results due to the corrupt practices that pervade the whole of migration regulation.

The study is dedicated to analyzing the complex interaction between Artificial Intelligence (AI) and the Internet of Things (IoT) with institutional structures in the context of sustainable development. This work examines the impact of these technologies on economic and social development, identifying their potential advantages and risks. Methodologically, the research relies on information gathering and case study analysis, assessing the impact of technology in various domains, from smart cities to the manufacturing sector. The findings emphasize the necessity of integrating technological innovations into broader social and environmental initiatives, highlighting the importance of institutional transformations for achieving environmental sustainability.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

The analysis of the key factors which prevent or contribute to the promotion and development of the Power Purchase Agreements (PPAs) in order to meet the sustainability goals represents an important issue which worth being investigated, especially in the situation in which entering in bilateral relations inside this contract has a powerful meaning in achieving new climate targets, developing and improving the use of green energy, and promoting a sustainable green economy. The main goal of this research is to identify and analyze the main factors which help or pre-vent the promotion and development of a PPA, in order to meet the sustainability goals by promoting a green economy. For this research survey based on comparative analysis, questionnaires and interviews with energy experts, Spearman’s correlation matrix and IBM SPSS Statistics for Window are also used. The results suggest that although there are positive interest and an open attitude towards the PPA from both sides (sellers and buyers), but there is still place for improvement, the lack of knowledge or the insufficient measures taken so far being two of the reasons way until now in Romania we do not have a developed PPA market and the level of knowledge regarding this type of mechanism is quite low.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

Achieving the dual development of rural revitalization and urbanization is an important strategic goal of China’s current modernization. Rural population and settlements are the main components of the countryside in traditional agricultural areas, and play an important role in the development of the countryside itself in terms of urban and rural land use and in the formation of urban and rural development patterns. This study analyzes the spatial and temporal changes in rural populations and settlements at the township level, as well as the degree and type of coupled development. A framework for urban–rural development relationships based on different types of coupled development is proposed, and a model of urban–rural forces is constructed to derive the spatial pattern of urban–rural development at the township level that may be formed in the future. Our study shows that the rural population and settlements in the study area are characterized by significant spatial and temporal dynamics, indicating that traditional rural areas are in a process of rapid development and change. The results of the township-level coupling measurements present four types of development in terms of the spatial pattern of urban–rural development: A-type is most likely to produce new cities or satellite towns in the Jixi–Harbin–Qiqihar area in the future; B-type is the fastest dying area in the future, located in the Harbin and Qitaihe clusters, with a tendency to merge into Harbin; C-type is the area to be focused on in the future to attract population and strictly control the growth of the rural settlement area to avoid it turning into B-type; D-type may develop regional township centers in the future in the combined area of Jiamusi City, Suihua City and Mudanjiang City. The results of the study provide experience in realizing rural revitalization according to local conditions. The new spatial pattern of urban–rural development provides an important reference for formulating land use policies, optimizing urban–rural land allocation and realizing integrated urban–rural development strategies.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

Wounds are an increasing global concern, mainly due to a sedentary lifestyle, frequently associated to the occidental way of life. The current prevalence of obesity in western societies, leading to an increase in type II diabetes, and an elderly population, are also a key factor associated to the problem of wounds healing. Therefore, it stands essential to find wound dressing systems allowing reestablishing the skin integrity in the shortest possible time and with the lowest cost, avoiding further damage and promoting patients´ well-being. Wounds can be classified into acute or chronic, depending essentially on the duration of the healing process, which is associated with. It depends on the extent and depth of wound, localization, level of infection and on the patient health status. For each kind of wound and respective healing stage there is a more suitable dressing. The aim of this review was to focus on the possible wound dressing management, aiming the more adequate healing approach for each kind of wound.

Globally, the need for sustainable urban development has never been more urgent than now. This is because estimates indicate that more than half of the global population will be living in urban areas by 2050, with South Africa estimated at 80%. This paper focuses on socio-economic nuances that impede sustainable urban development, as well as the strategies that can accelerate sustainable urban development in South Africa. Through a literature review methodology, the analysis identified the following issues as impediments to sustainable urban development in South Africa, informal settlements and businesses, lack of consultations with urban citizens, unresolved apartheid legacies, violence, crime and insecurity, and migration and immigration intricacies in South Africa. The paper also established the strategies to accelerate sustainable urban development as working with informality and against it, promoting inclusivity and access to resources, formulating, and accelerating policy reforms, investing in rural areas and towns, and finally investing in superior technology and innovation. These findings imply that there is a need to seek alternative development models and approaches, to address social challenges such as poverty, unemployment, and poor housing, aspects that impact negatively on urban development planning and sustainable development. This is because the major challenges to sustainable urban development are human-related challenges, that need social and economic solutions. There is also a need to reduce rural-urban migration by developing rural towns to ease pressure in major towns which are already spilling over.

With buildings accounting for a significant portion of global energy consumption and greenhouse gas emissions, the application of artificial intelligence (AI) holds promise for enhancing sustainability in the building lifecycle. This systematic literature review addresses the current understanding of AI's potential to optimize energy efficiency and minimize environmental impact in building design, construction, and operation. A comprehensive literature review and synthesis were conducted to identify AI technologies applicable to sustainable building practices, examine their influence, and analyze the challenges of implementation. The review was guided by a meticulous search strategy utilizing keywords related to AI application in sustainable building design, construction, and operation. The findings reveal AI's capabilities in optimizing energy efficiency through intelligent control systems, enabling predictive maintenance, and aiding design simulation. Advanced machine learning algorithms facilitate data-driven analysis and prediction, while digital twins provide real-time insights for informed decision-making. Furthermore, the review identifies barriers to AI adoption, including cost concerns, data security risks, and challenges in implementation. AI presents a transformative opportunity to enhance sustainability in the built environment, offering innovative solutions for energy optimization and environmentally conscious practices. However, addressing technical and practical challenges will be crucial for the successful integration of AI in sustainable building practices.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Globalization, knowledge economy, information technology advancements, and the rise of learning societies contribute to the concept of a learning city. The study examines the economic indicators of Yazd city, Iran, in the context of learning city development. A descriptive-analytical approach with a survey method and cluster sampling was employed. Data analysis involved Kolmogorov-Smirnov normality test, single-sample T-test, simple linear regression, and Kendall's W test. The normality test confirmed data normality. The T-test indicated that experts perceived the current state of most variables in Yazd as undesirable. Regression analysis revealed a significant positive association between the economic index and independent variables. Kendall's W test prioritized areas based on economic indicators, with the top 7 and bottom 5 areas identified for focused interventions. The study emphasizes the need to prioritize areas within Yazd based on their economic indicators. This prioritization informs strategies for enhancing social and legal aspects of Yazd's transformation into a learning city. Further research should explore effective methods to cultivate a full-fledged learning environment in the city.

Keywords: contamination; bioaccumulation; fish and mollusks tissue; ecosystem components; heavy metals; organochlorine pesticides; polychlorinated biphenyls; polycyclic aromatic hydrocarbons.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (&gt;70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

The focus of this work lies in the construction of monitoring system designed in the form of a patch using a long-lasting potentiometric electrolyte concentration sensor from metal electrodes, in a galvanic cell configuration Mg(s)|NaCl(aq)|Cu(s). Initially, a mathematical analysis was conducted on the expected sensor output through the Nernst equation. The experimental phase involved conducting controlled tests in the laboratory using various molar concentrations of sodium chloride (NaCl) in aqueous solution. Results showed that the electrolyte sensor allows for monitoring electrolyte levels in NaCl in the range of 0.02 to 1 M/L, with electrode lifespan exceeding 10 days. On the other hand, when patch is using human sweat during controlled exercise routines, it showed the sensor's capability for monitoring changes in the subjects' hydration levels in real time. The sensor output potential is greater than 1.7 volts when the sensor electrodes are in contact with human sweat, which is equivalent to measuring molar concentrations at normal hydration and moderately high hydration levels. Sensor results indicate that the system can function in a self-powered manner without external batteries. Additionally, the extended lifespan of its electrodes allows for continuous monitoring of imbalances in the human body, showcasing the system capability for long-term health assessment.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

Synanthropic flora (weeds, spontaneously developed plants) are plants that accompany humans, appearing as a result of anthropopressure as well as after its cessation. The potential of synanthropic flora in shaping green areas usually brings many measurable benefits that depend on land management in cities. The study aimed to determine the preferences and attitudes of adults towards synanthropic flora in settlement units. The article presents survey results from 447 city residents. The obtained results were statistically analyzed using the k-means clustering method to identify segments of respondents with similar attitudes and preferences toward synanthropic flora. Mann-Whitney U tests were employed to determine statistical differences in the demographic variables among the analyzed clusters of respondents. Additionally, multiple regression analysis was performed to identify the opinions and attitudes towards synanthropic flora, that may influence their greater acceptance in the vicinity of residential areas. The results obtained in multiple regression allow for the statement that the respondent’s evaluation of the level of support for the introduction of more synanthropic vegetation into urban greenery (Yw) grows with the increase of acceptance of synanthropic plants occurrence in surroundings. Respondents’ opinions on the subject of the presence of synanthropic plants were studied using such variables concerning: synanthropic vegetation found in turfgrasses has a positive impact on the visual attractiveness of a site (X1), synanthropic plant communities present themselves better than others (X2), presence of synanthropic vegetation in an estate improves the quality of life in that location (X3), introduction of synanthropic flora into estate arrangements is a positive (X4), support for the use of synanthropic flora for educational purposes - as elements of playgrounds or in the form of environmental workshops (X5). Residents’ acceptance of synanthropic flora in green areas is at a relatively high level.

The concept of a "circular economy" needs a more cogent theoretical anchor which will allow for transference of its goals and methods of attainment across cases. Tensions between ecological goals of this concept and the social implications of its implementation need to be addressed. This paper attempts to provide a theoretical framework for harnessing the strengths of a circular economy. Building on theories of social ecology which are predicated in Murray Bookchin's notion of "dialectical naturalism", the analysis presented here addresses some of the criticism of circular economic paradigms, such as their potential for stifling innovation or a neglect of human development challenges. A model for managing human "need" and "greed" within a circular economy framework is presented that also incorporates consumer choice and innovation. Planned obsolescence as a means of livelihood generation is also problematized with a view towards balancing durability of products on the one hand and ensuring throughput for manufacturing employment and innovation incentives on the other. Finally, the need for governance systems is considered to ensure that a planetary vision for a circular economy can be realized that efficiently harnesses local initiatives rather than an atomized and insular view of circularity.

Throughout the Covid19 period, families were forced to stay indoors, adapting to online school-ing, remote work, and virtual social engagements, inevitably altering the dynamics within households. There is a notable increase in mental health challenges in terms of anxiety and de-pression in children and adolescents. This study intends to explore the psychosocial effects of the Covid-19 pandemic in Italian families adopting self- and proxy-report questionnaires on anxiety, anger, and health-related quality of life. The results showed that approximately 20% obtained a clinical anxiety score and only 10% obtained a clinical anger score. There was found a difference in the perception of the quality of life reported by the child and that perceived by the parent. The stepwise regression model showed that total anxiety scores were predicted by sex, quality of life scores from the parents' self-report version and total anger score. Another stepwise regression model identified physiological and social anxiety as the best predictors that impact the quality of life. Parental well-being actively influences the well-being of children, so it is fundamental to implement preventive programmes and promote child well-being providing parents the most adequate support possible.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

This study delves into the intricate interplay of economic growth components, specifically focusing on Consumption and investment in Saudi Arabia from 2000 to 2022. Employing vector error correction models and cointegration techniques, we analyze the short- and long-term dynamics within the relationship of Consumption, investment, and economic growth. Granger causality analysis is also used to discern these pivotal variables' causal connections. Our empirical analysis reveals a persistent long-term cointegration relationship among the variables, underscoring the enduring nature of their interdependency. Furthermore, our findings highlight Consumption and investment's statistically significant positive impact on economic growth. Notably, the short-term analysis unveils a stable model characterized by an annual adjustment to equilibrium of 100%.Moreover, the Granger causality study demonstrates unidirectional causal linkages between Consumption, investment, and economic growth. These findings hold substantial implications for policy formulation in Saudi Arabia. Policymakers must grasp the ramifications of burgeoning prosperity and evolving private consumption patterns on future environmental outcomes. Achieving sustainable long-term results necessitates equal emphasis on bolstering private Consumption and fostering other facets of economic growth.

Aimed to obtain purple garlic varieties, 360 bolting bulbs from the Protected Geographical Indication (PGI) “Las Pedroñeras” were selected for their size, and the presence of abundant external scales. After a further selection, 243 out of the 360 bulbs were discarded due to undesired characteristics, as light purple color, high number of small cloves, cloves affected by Fusarium spp. and mites, among other. It was stablished that each bulb would give rise to a family. Thus, 117 families were planted under a random design during season 2021-2022. Either physiological, morphological and phenological traits were assessed for each family, and the affectations by pest and pathogens were also controlled. After the assessment of this trial, 103 out 117 families remained in the program, and were used for the establishment of a second trial the next season. Unlike the first trial, after the evaluations only 23 families remained in the program. There was observed a high variability for most of traits, with a great influence of families. The phenotypic behavior of families was significative influenced by environment, highlighting the need of their assessment under different environmental conditions. The high variability registered for the target sample, opens the possibility to select new garlic varieties from this PGI.

Brazil has ideal conditions for the large-scale use of cabotage cargo transportation: a vast coastline with almost 7,400 km, approximately 70% of the population resident in a coastal range of up to 200 km from the coast and a strong concentration of activities economic along the coast. However, there is an absolute domain of road modal for the transportation of goods, and cabotage is underused. The purpose of the study was to raise the main barriers that negatively impact the performance of Brazilian cabotage. To this end, it was used to bibliographic and documentary research, based on studies already published in journals, doctoral theses, master's dissertations, congress annals, technical reports and research on government-related government agencies sites, navigation companies and entities related to cabotage. The main barriers that contribute to the low use of cabotage in Brazil were identified and analyzed, as well as possible alternatives of solution for sustainable development of this mode of transport. Such a study will certainly serve as subsidies for the definition of public policies aimed at better use of Brazilian cabotage, as well as to encourage navigation companies to invest more in the transport of goods by cabotage, in order to contribute to the reduction of trucks on highways Brazilian and for environmental preservation.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

This research analyzes the phenomenon of the reduction of urban green spaces in the post-socialist city. Belgrade was selected as a post-socialist city of the former Yugoslavia. The article analyses the views of urban planners on the reasons for the reduction of urban green areas in the post-socialist city based on semi-structured interviews with representative samples for urban areas. This result research confirms the hypothesis that post-socialist city planning reduces urban green areas due to the lack of new mechanisms in documents for the planning of urban green space. The concept of sustainability should connect and balance the skills of urban planners and focus on how urban planners develop and apply standards and protect them in market-democratic systems. In other words, a new mechanism of post-socialist city planning implies a balance between the private and public sectors. In the planning document, urban planners should find a common denominator between the public interest, citizens, investors, and spheres determined by the sustainable principles of the development. City institutions should provide opportunities for the application of those standards. With the new approach, planning would imply work in the service of citizens in the concepts of a sustainable and green city.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

In this study, an attempt was made to investigate the Kenya case of multivariate causality of carbon dioxide emissions by employing a time series data spanning from 1961-2011 using the ARDL method of cointegration analysis. The long-run elasticities show that, a 1% increase in financial development increases carbon dioxide emissions by 0.28%, a 1% increase in GDP per capita increases carbon dioxide emissions by 1.32% and a 1% increase in urbanization decreases carbon dioxide emissions by 1.14%. There was a unidirectional causality running from financial development, food production index, GDP per capita, industrialization and urbanization to carbon dioxide emissions. The innovation accounting shows that 20% of future shocks in carbon dioxide emissions are due to fluctuations in financial development, 9% of future shocks in financial development are due to fluctuations urbanization and 22% of future shocks in food production index are due to fluctuations in carbon dioxide emissions.

Periodontitis is a chronic inflammatory disease which results in the destruction of the tooth’ s supporting tissues and the alveolar bone resorption. The complement becomes a major link between infection and inflammatory pathology including periodontitis. Gingipians as important virulence factors of P. gingivalis have the activity of C5 convertase, could cleave C5 into fully functional C5a to activate C5aR. The above process could be blocked by the C5aR antagonist (PMX-53) to suppress local periodontal inflammation, and then achieves the purpose of treatment of periodontitis. Nanoparticles incorporated within gelatin are promising carrier system for drug delivery in recent years. This study aimed to investigate whether gelatin nanoparticles loaded with PMX-53 prevents alveolar bone resorption in miniature swines model of periodontitis. Four miniature swines were placed ligatures around the maxillary and mandibular fourth premolar and first molar on both sides for seven weeks to induce periodontitis. Then, animals were assigned randomly to four groups: minocycline-treated group, gelatin with PMX53-treated group, gelatin-treated group and a sham control group. They were treated with 1ml related drugs respectively, into gingival sulcusl for 4 times at one-week intervals. We showed that local treatments with gelatin nanoparticles loaded with PMX-53 could inhibit alveolar bone loss of periodontitis. Our study revealed that gelatin nanoparticles loaded with PMX-53 prevented alveolar bone resorption miniature swines model of periodontitis. In addition, provided proof-of-concept for local targeting of gelatin nanoparticles loaded with PMX-53 as a powerful candidate for the treatment of periodontitis.

These findings have several policy implications, emphasizing the need for enhanced data collection, climate-resilient agricultural policies, and continued investment in research. The study contributes to the understanding of climate-smart agriculture, providing insights for informed decision-making towards resilient and productive agricultural systems in the face of climate change challenges.

Walls-like structured monoclinic WO3 thin films were obtained by spray deposition method for further integration in gas sensors. For sensing applications, it is very important to achieve a high surface-to-volume ratio surface together with a proper thin films structure. The present communication reports on the effect of the sprayed solution volume variation (as a thickness variation element) on the detailed Raman spectroscopy for WO3 thin films with different thicknesses grown from precursor solutions with two different concentrations. Detailed analysis of the two series of samples shows that the growing thickness strongly affects the films morphology while their crystalline structure is only slightly affected. The Raman analysis contribute to refining the structural features clarifications. It was observed that, for both concentrations, the increase in thickness seems to slightly affect the stoichiometry of material and, in association with surface morphology variations, provide new possibilities for fine tuning of films properties towards enhanced as sensing applications. Further studies are ongoing.

This paper aims to stress the nexus between sustainable development, economic freedom and local participatory democracy in 21 European smart cities. The development of smart cities is strongly correlated with technological advancements and improved access to pub-lic services for all residents. Furthermore, smart cities are characterized by efficient man-agement of social, economic and environmental resources and a strong partnership be-tween the public and private sectors. The paper aims to map the dynamics of local partic-ipatory democracy in European smart cities and to identify several relevant predictors of local participatory democracy. The sample is represented by 21 European capitals (20 EU countries plus UK), which are included in the Smart City Index (SCI). Using the quantita-tive design based on both statistical regressions and structural equations modelling (SEM), the paper shows positive statistical correlation between economic factors, sustainable de-velopment, political culture, education and the level of local participatory democracy. Be-sides the exogenous variables, the study emphasized the main priority areas, which might be seen as urgent issues for local governments. The conclusion of the paper underlines the fact that economic freedom, sustainable development, upper secondary education, afford-able housing and an increased level of citizens’ engagement could predict further evolu-tions of the local participatory democracy in 21 European capitals.

Few studies have explored the gender wage gap among farmworkers, and there is a notable absence of research on how farm wages impact household welfare differently based on gender. This study aims to fill this gap by examining how farm wages affect gender disparities in household welfare among farmworkers in Nigeria. Using survey data from 720 farmworkers, we investigated gender-based differences in household welfare. Our approach combined parametric methods (Blinder-Oaxaca decomposition) to assess gender gaps in household welfare and non-parametric techniques (Propensity Score Matching, PSM) to estimate the effects of farm wages. The analysis reveals that female farmworkers experience significantly lower per capita food consumption expenditure (₦11,486.51 less) compared to their male counterparts. These disparities partly stem from differences in socioeconomic factors, job characteristics, and enterprise attributes between male and female farmworkers. The study underscores the role of farm wages in mitigating gender gaps in household welfare, demonstrating that farm wages have increased per capita food consumption expenditure for female farmworkers by ₦6,640.698. This finding highlights the potential of wage increases to enhance livelihoods, underscoring the importance of equitable wage policies in farming. Furthermore, our findings emphasize that the impact of farm wages on welfare varies with household characteristics, suggesting the need for targeted interventions tailored to enhance identified household attributes. Addressing these factors could effectively reduce gender inequalities in farm work and contribute to overall welfare improvements.

Carbonate reservoirs, influenced by depositional and diagenetic processes and characterized by features like faults and vugs that impact storage capacity, require more than traditional Borehole Imaging logs (BHI) for accurate porosity data. This data is essential for geological assessments, production forecasting, and reservoir simulations. This work aims to address this limitation by developing methods to measure and monitor the sustainability of carbonate reservoirs and exploring the application of sustainability principles to their management. The study integrates BHI and conventional logs from two wells to classify porosity-based facies within the Barra Velha Formation (BVF) in the Santos Basin. The methodology involves four steps: (i) analyzing conventional logs; (ii) segmenting BHI logs; (iii) integrating conventional and segmented BHI logs using Self-Organizing Maps (SOM); and (iv) interpreting the resulting classes. Matrix porosity values and non-matrix pore sizes categorize the porosity into four facies (A to D). Facies A has high non-matrix porosity with 14,560 small megapores, 5,419 large megapores, and 271 gigapores (71.9%, 26.76%, and 1.34% of the 20,250 pores, respectively). Facies B shows moderate non-matrix porosity with 8,669 small megapores, 2,642 large megapores, and 33 gigapores (76.42%, 23.29%, and 0.29% of the 11,344 pores, respectively) and medium matrix porosity. Facies C exhibits low non-matrix porosity with 7,749 small megapores, 2,132 large megapores, and 20 gigapores (78.27%, 21.53%, and 0.20% of the 9,901 pores, respectively) and medium matrix porosity. Facies D has low non-matrix porosity with 9,355 small megapores, 2,346 large megapores, and 19 gigapores (79.82%, 20.02%, and 0.16% of the 11,720 pores, respectively) and low matrix porosity. The novelty of this work lies in integrating data from two sources to classify porosity across the Pre-Salt reservoir interval, serving as a proxy for preliminary litho-facies identification without core data. This study advances our understanding of carbonate reservoir sustainability and heterogeneity, offering valuable insights for robust, sustainable reservoir characterization and management in the context of global environmental and geological changes.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

Wildfires have always been a part of the history of Mediterranean forests. However, forest regeneration after a wildfire is not certain. It depends on many factors, some of which may be influenced by land management activities. Failure of regeneration will cause a regime shift in the ecosystem, reducing the provision of ecosystem services and ultimately leading to desertification. How can we increase Mediterranean forests’ resilience to fire? To answer this question, we did a literature review, investigating chains of processes that allow forests to regenerate (which we label “regeneration mechanisms”), and assessed the impact of selected management practices documented in the WOCAT database on the regeneration mechanisms. We identified three distinct regeneration mechanisms that enable Mediterranean forests to recover, as well as the time frame before and after a fire in which they are at work, and factors that can hinder or support resilience. The three regeneration mechanisms enabling a forest to regenerate after a fire consist of regeneration (1) from a seed bank; (2) from resprouting individuals; and (3) from unburned plants that escaped the fire. Management practices were grouped into four categories: (1) fuel breaks, (2) fuel management, (3) afforestation, and (4) mulching. We assessed how and under what conditions land management modifies the ecosystem’s resilience. The results show that land management influences resilience by interacting with resilience mechanisms before and after the fire, and not just by modifying the fire regime. Our analysis demonstrates a need for adaptive – i.e. context- and time-specific – management strategies.