The time-resolved flowfield of a spatially oscillating jet emitted by a Sweeping Jet (SWJ) actuator is investigated numerically using three-dimensional Reynolds-averaged Navier-Stokes (3D-URANS) equations. Numerical simulations are performed for a practical range of mass flow rates providing flow conditions ranging from incompressible to subsonic compressible flows. A linear relationship between the mass flow rate and the jet oscillation frequency is found. The results of the numerical model are compared with the experimental data in the literature, and good agreement is found. Additionally, it is observed that the SWJ actuator frequency response switches from one linear mode to another linear mode when the compressibility effects become important.

CO2 flooding stands as a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in its oil recovery, yet a comprehensive quantitative analysis remains an area in need of refinement. In this study, we have developed 1D and 2D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly-miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns are determined. A novel approach of the contour area calculation method is introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding geological parameters, oil viscosity, and injection-production parameters. Furthermore, the Random Forest (RF) algorithm is employed to identify the controlling factor of the sweep coefficient, as determined by out-of-bag (OOB) data displacement analysis. The results show that the miscible front is located at the point of maximum CO2 content in the oil phase. The immiscible front occurs at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moves at a faster rate compared to the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impact the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibits the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio is a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection-production parameters also play a pivotal role in sweep coefficient. Decreased well spacing and increased gas injection rates are found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates can improve the miscibility degree of partly-miscible flooding from 0.69 to 1.0. Oil viscosity proves to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly-miscible flooding patterns. Conversely, gravity segregation primarily governs the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerges as a paramount influence, with a factor importance value (FI) reaching 1.04. these results provide a theoretical foundation for the application of CO2 flooding, enhancing the understanding of the critical factors governing its success.

In this data deposit, I describe a dataset that is the result of content mining 167,318 published articles for statistical test results. As a result of this content mining, 688,112 results from 50,845 articles were extracted. In order to provide a comprehensive set of data, the statistical results are supplemented with metadata from the article they originate from. The dataset is provided in a comma separated file (CSV) in long-format. For each of the 688,112 results, 20 variables are included, of which seven are article metadata and 13 pertain to the individual statistical results (e.g., reported and recalculated p-value). A five-pronged approach was taken to generate the dataset: (i) collect journal lists, (ii) spider journal pages for articles, (iii) download articles, (iv) add article metadata, and (v) mine articles for statistical results.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

A testable hypothesis with quantitative predictions is put forward, proposing that strong acids produced on land are a major cause of increasing atmospheric pCO2. Our modelling analysis of reactions by dissolved inorganic carbon shows that increasing atmospheric CO2 could be caused thermodynamically by falling land surface pH values. This hypothesis challenges the imbalance assumed between the global uptake of CO2 by photosynthesis and emissions of CO2 from all sources, including the combustion of fossil fuels. Strong acids generated by oxygen from reduced nitrogen and sulphur emits CO2 almost stoichiometrically from dissolved bicarbonate in the pH range of most global soils from pH 6.5 to above 8. Each general decrease of aqueous pH value of 0.01 units from acidification of surface water potentially increases the pCO2 in the atmosphere by about 7 ppmv. Contrary to prevailing assumptions that CO2 emissions from combusting fossil fuels can remain in the atmosphere for more than a millennium, such emissions may be partly nullified by global greening from enhanced rates of photosynthesis as well as oceanic absorption. The surface pH value of the ocean has been shown to decrease as atmospheric pCO2 rises. Therefore, our qualitative estimates of increasing atmospheric CO2 driven by irreversible acidification on land are critical and need broad scale validation. To the extent that significant acidification of the land is occurring, through export of alkaline produce, the use of artificial nitrogen fertilisation and possible other causes, the prevailing methods of reducing CO2 emissions will fail. However, these acidifying processes on land have not been considered by previous biogeochemical reviews. Despite counter measures, including carbon capture and geological storage, the increasing Keeling curve for pCO2 may continue to rise because zero carbon policies do not address such a major cause. This hypothesis can be tested by in situ experiments in neutral soils and water, designed to compare CO2 emissions under the acidifying conditions described in this article with those when corrective counter measures are applied.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

This study delves into the intricate interplay of economic growth components, specifically focusing on Consumption and investment in Saudi Arabia from 2000 to 2022. Employing vector error correction models and cointegration techniques, we analyze the short- and long-term dynamics within the relationship of Consumption, investment, and economic growth. Granger causality analysis is also used to discern these pivotal variables' causal connections. Our empirical analysis reveals a persistent long-term cointegration relationship among the variables, underscoring the enduring nature of their interdependency. Furthermore, our findings highlight Consumption and investment's statistically significant positive impact on economic growth. Notably, the short-term analysis unveils a stable model characterized by an annual adjustment to equilibrium of 100%.Moreover, the Granger causality study demonstrates unidirectional causal linkages between Consumption, investment, and economic growth. These findings hold substantial implications for policy formulation in Saudi Arabia. Policymakers must grasp the ramifications of burgeoning prosperity and evolving private consumption patterns on future environmental outcomes. Achieving sustainable long-term results necessitates equal emphasis on bolstering private Consumption and fostering other facets of economic growth.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

(1) Background: Cardiorespiratory fitness (CRF) is a prognostic factor regarding long time morbidity and mortality. To assess CRF the well-known gold standard is cardiopulmonary exercise testing (CPET), which is a time consuming and expensive test. Therefore, alternative methods for routine evaluation of CRF are needed for the general population as well as for specific patient groups such as children and young adults with congenital heart disease. The Stair Climbing Test (SCT) is a simple and resource saving test reported in the current literature. This test is used in various settings to assess different health associated risk factors including cardiorespiratory fitness, muscular resilience, therapy effectiveness or pre- and postoperative morbidity and mortality.

As time continues to advance, the need for robust security threat mitigation has become increasingly vital in software. However, ensuring early effective security threat mitigation requires optimal test data and consistent test case design. It is a constant struggle to maximize test coverage through test data optimization. We conducted explanatory research to maximize test coverage of security requirements as modeled in Structured Misuse Case Description (SMCD) i.e., structured specification of misuse case, so as to improve consistency in optimal test data generation. We specified constraints upon Mal activity in Object Constraint Language (OCL) in order to minimize human dependency and improve consistency in optimal test data generation. It was evident through results that MC/DC generated optimal test data of security threats through SMCD in comparison to the Decision Coverage method thus resulting in designing a significantly lower number of test cases and yet maximizing test coverage of security threats. MC/DC generated test data with n+1, while Decision Coverage generated test data with〖 2〗^n, we, therefore, conclude that MC/DC maximizes test coverage through optimal test data from SMCD in comparison to Decision Coverage.

Then the purposes of this study were to compare and correlate the aerobic threshold (TH_aer) and anaerobic threshold (TH_anaer) measured during a new single judo specific incremental test and Treadmill Test for aerobic demand evaluation. Eight well-trained male competitive judo players (24.3±7.9 years; height of 169.3±6.7cm; fat mass of 12.7±3.9%) performed a maximal incremental specific test for judo mimicking the UchiKomi drills and on treadmill in different days. There was difference between specific and general TH_aer (P=0.0006) as well as weak correlation for TH_aer (r=0.32; R²=0.1; P=0.2) and TH_anaer (rs=-0.31; R²=0.1; P=0.12). When correlation was applied with normalized data (percentage of peak load) we observed moderate correlation for TH_aer (r=0.76; R²=0.58; P=0.027), but the same was not observed for TH_anaer. We conclude that there is a need of TH_aer and TH_anaer evaluation through a specific test for Judo.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Background: Open AI developed ChatGPT, a language model based on the GPT architecture, designed for text-based communication. Trained on diverse internet texts, ChatGPT generates contextually appropriate responses using machine learning. It understands input through analysis and context interpretation, generating coherent and contextually relevant responses. Interaction is possible through messaging platforms. Materials and Methods: In November 2023, we utilized ChatGPT 3.5, the default version at that time, to answer questions from the Italian National Residency Program Admission Tests (SSMs) of 2021, 2022, and 2023. The questions cover clinical, diagnostic, analytical, therapeutic, and epidemiological scenarios, sometimes accompanied by images. The study compared ChatGPT's answers to the official corrections on the Italian Ministry of University and Research (MUR) website. The scoring method used for evaluation was 1 point for correct answers, 0 points for unanswered questions, and -0.25 points for incorrect answers, reflecting the SSM test scoring system. Results: In summary, ChatGPT was tested with a total of 420 questions, 140 for each test. It achieved an overall accuracy of 80.48%, providing correct answers for 338 questions and incorrect answers for 82 questions. When faced with questions containing both text and images, it answered 55% correctly and 45% incorrectly. The model's performance varied over time, with an 82.14% accuracy rate in 2021 and 2022 (115 correct out of 140) and a 77.14% accuracy rate in 2023 (108 correct out of 140). Applying thisscoring method to the SSM test, ChatGPT would have scored 105 points in 2021 and 2022, and 100 points in 2023. Conclusions: ChatGPT has exhibited above-average performance in the last three SSM tests, highlighting its robust capability to interpret clinical scenarios and offer precise diagnostic and therapeutic guidance. Despite this, some limitations persist, notably the software's inability to interpret non-textual information.

This study introduces and demonstrates a comprehensive, accurate, unbiased approach to robust quantitative comparison of Electronic Nicotine Delivery Systems (ENDS) appropriate for establishing substantial equivalence (or lack thereof) between tobacco products. The approach is demonstrated across a family of thirteen pen- and pod-style ENDS products. Methods employed consist of formulating a robust emissions surface regression model, quantifying the empirical accuracy of the model as applied to each product, evaluating relationships between product design characteristics and maximum emissions characteristics, and presenting results in formats useful to researchers, regulators, and consumers. Results provide a response surface to characterize emissions (total particulate matter and constituents thereof) from each ENDS appropriate for use in a computer model and for conducting quantitative exposure comparisons between products. Results demonstrate that emissions vary as a function of puff duration, flow rate, E-Liquid composition, and device operating power. Further, results indicate that regulating design characteristics of ENDS devices and consumables may not achieve desired public health outcomes; it is more effective to regulate maximum permissible emissions directly. Three emissions outcome measures (yield per puff, mass concentration and constituent mass ratio) are recommended for adoption as standard quantities for reporting by manufacturers and research laboratories. The approach provides a means of (a) quantifying and comparing maximal emissions from ENDS products spanning their entire operating envelope, (b) comparative evaluation of ENDS devices and consumable design characteristics, and (c) establishing comparative equivalence of maximal emissions from ENDS. A consumer-oriented product emissions dashboard is proposed for comparative evaluation of ENDS exposure potential. Maximum achievable power dissipated in the coil of ENDS is identified as a potentially effective regulatory parameter.

We develop a primality test for Mersenne numbers and investigate the primality of the sequence of Catalan-Mersenne numbers. We use induction as a proof to show that the 5th Catalan-Mersenne number is a prime number, thus demonstrating the infinitude of Mersenne primes.

The BH 25 railway bridge, located in Indonesia, consists of three spans: 9.5 m (span-1 girder type), 21.9 m (span-2 truss type), and 9.6 m (span-3 girder type). Despite the initial plan for camber, it was not achieved, leading to the installation of temporary support on span-2. To assess the level of damage and determine the necessary steps, static and dynamic tests were conducted using a CC206 locomotive. The maximum deflection was recorded at -4.60 mm for span-1, -11.30 mm for span-2, and -3.42 mm for span-3. The dominant frequency in the vertical direction of span-2 was found to be 14.65 Hz. Due to the inability to achieve the planned camber and the subsequent removal of temporary support, external prestressing will be implemented, resulting in a camber of 11.82 mm. This change in prestressing also affects the dominant frequency of span-2, which becomes 17.07 Hz.

Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

Patients with a psychotic disorder frequently report oral health problems, while mental health nurses (MHNs) seem not to be fully aware of these problems and the risk factors. Therefore, this study aims to develop supportive tools for MHNs regarding oral health to increase sensitization among MHNs and to provide MHNs with knowledge to recognize (potential) oral health problems in patients with a psychotic disorder. We used a human-centered design in which the user, MHNs as well as experts by experience, were placed in the centre of the research process. Problems and needs in MHNs working with patients with a psychotic disorder were addressed. To identify key issues of problem as well as the needs in terms of resources, we started with focus groups (n = 9). We analysed the data thematically based on context of patients and MHNs in practice regarding oral health, preferred oral health tools focused on MHN, and intended outcomes of tools. A Multi Criteria Decision Matrix was developed and analysed (n = 9) to identify the most optimal and viable solution based on established criteria and issues that are prevalent in the work of MHNs. Most promising result was the development of a brochure with an awareness screener. The brochure with awareness screener was developed as a low-fidelity prototype for MHNs regarding oral health in patients with a psychotic disorder, based on the latest scientific evidence. After testing it, the feasibility was tested through semi-structured interviews (n=19). MHNs and experts by experience were satisfied with the tool and provided recommendations for adjustments to the content. Significant augmentations to the brochure include a clinical lesson and a toothbrush with toothpaste for patients. We can conclude that a brochure with an awareness screener is feasible for MHNs. Future steps aiming to further refine and optimize care processes for oral health tools in MHNs, should take refining eligibility criteria for psychiatric populations and the language level of the target group of a tool into account.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Speckle Plethysmography (SPG) and Photoplethysmography (PPG) are different biophotonics technologies that allow for measurement of hemodynamics. As the difference between SPG and PPG under low perfusion conditions is not fully understood, a Cold Pressor Test (CPT) was used to modulate blood pressure and peripheral circulation. A custom-built setup simultaneously derived SPG and PPG from the same video streams at two wavelengths (639 nm and 850 nm). SPG and PPG were measured at right index finger location before and during CPT using finger Arterial Pressure (fiAP) as reference. The effect of CPT on Alternating Component amplitude (AC) and Signal-to-Noise-Ratio (SNR) of dual-wavelength SPG and PPG signals was analysed across participants. Furthermore, waveform differences between SPG, PPG, and fiAP based on frequency harmonic ratios, were analysed for each subject (n=10). Both PPG and SPG at 850 nm show a significant reduction during CPT for both AC and SNR. However, SPG showed significantly higher and more stable SNR than PPG in both study phases. Harmonic ratios were found substantially higher in SPG than PPG. Therefore, in low perfusion conditions, SPG seems to offer a more robust pulse wave monitoring with higher harmonic ratios than PPG.

Nowadays, some coffee production centers are still classification manually, so it requires a very long time, a lot of labor, and expensive operational costs. Therefore, the purpose of this research was to design and performance of the coffee bean classifier that can accelerate the process of classification beans. The classifier used consists of three main parts, namely the frame, driving force, and sieves. Research parameters include classifier work capacity, power, specific energy, classification distribution and effectiveness, and efficiency. The results showed that the best operating conditions of the coffee bean classifier was found at a rotational speed of 91.07 rpm and a 16° sieves angle with a classifier working capacity of 38.27 kg/h, the distribution of the seeds retained in the first sieve was 56.77 %, the second sieves was 28.12%, and the third sieves was 15.11%. The efficiency of using a classifier was found at a rotating speed of 91.07 rpm and a sieves angle of 16°. This classifier was simple in design, easy to operate, and can sort coffee beans into three classification, namely small, medium, and large.

In this paper, Lie symmetry and Painlevé Techniques are applied to the SIRD (Susceptible, Infected, Recovered and Dead) model. A demonstration of the integrability of the model is provided to present an exact solution. The study revealed that nonlinear system passes Painlevé test and does not possesses complex chaotic behaviour. However, the system fails to pass the Painlevé test while constraints reach values equivalent to the corresponding complex chaotic behaviour. The two-dimensional Lie symmetry algebra and the commutator table of the infinitesimal generators are obtained. Lie symmetry analysis serves to linearize the nonlinear system and find the corresponding invariant solution.

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.

Thermal stresses belong to the leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature properties of asphalt mixtures, three point bending and uniaxial tensile creep tests were applied and the master curves of stiffness modulus were analyzed. On the basis of creep test results, rheological parameters describing elastic and viscous properties of the asphalt mixtures were determined. Thermal stresses were calculated and compared to tensile strength of the material to obtain the failure temperature of the analyzed asphalt mixtures. It was noted that lower strain values of creep curves were obtained for the Tensile Creep Test (TCT) than for the Bending Beam Creep Test (BBCT), especially at lower temperatures. Results of thermal stress calculations indicated that higher reliability was obtained for the viscoelastic Monismith method based on the TCT results than for the simple quasi-elastic solution of Hills and Brien. The highest agreement with the TSRST results was also obtained for the Monismith method based on the TCT results. No clear relationships were noted between the predicted failure temperature and different methods of thermal stress calculations.

I propose a test for machine self-awareness inspired by the Turing test. My test is simple, and it provides an objective, empirical metric to rectify the ungrounded speculation surging through industry, academia, and social media. Drawing from a breadth of philosophical literature, I argue the test captures the essence of self-awareness, rather than some postulated correlate or ancillary quality. To begin, the concept of self-awareness is clearly demarcated from related concepts like consciousness, agency, and free will. Next, I propose a model called the Nesting Doll of Self-Awareness and discuss its relevance for intelligent beings. Then, the test is presented in its full generality, applicable to any machine system. I show how to apply the test to Large Language Models and conduct experiments on popular open and closed source LLMs, obtaining reproducible results that suggest a lack of self-awareness. The implications of machine self-awareness are discussed in relation to questions about meaning and true understanding. Finally, some next steps are outlined for studying self-awareness in machines.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

In order to study the influence of falling rock shape on its rolling characteristics and realize the optimization of falling rock protection design, the following research was carried out. Design model experiments to explore the rolling characteristics of different shapes of rockfalls. Based on the experimental results, it was found that the slenderness ratio, center of gravity, and rotational inertia of the rockfalls can affect their rolling characteristics, leading to swaying and changing the rolling axis during the rolling process, thereby affecting their rolling speed. On this basis, the formation mechanism of rolling resistance is analyzed, and the main cause of energy loss is the rolling resistance arm formed with the rolling surface during rockfall rolling, and a shape parameter to quantify the rolling resistance is proposed. The parameters are substituted into the kinematic formula, in which the influence of the rockfall shape, slope and slope roughness on the rolling speed is considered. Combined with the offset and initial position of the rockfall, the formula can be used to calculate the rolling speed and impact energy in the rolling region and any position in the region. The calculation formula was validated using model experimental data, and the results showed that the error between the experimental and calculated values was small. The error was corrected based on the experimental data. After on-site testing and verification, it can provide reference for the management of rockfall disasters.

For the symmetrical mixture model and mixture test area, the lattice point set is used to partition, and then the corresponding test statistics can be constructed. In this paper, we first proposes the partition methods under the lattice point sets and obtains several sub-simplexes without common interior points. Furthermore, we present the method for constructing a uniform design on the simplex using the center points of these sub-simplexes. The designs satisfy the uniformity of maximum distance deviation and provide good results for the mean square error deviation. Finally, the uniformity test on the mixture region is considered and illustrated by examples.

In this paper, by extending some results of informational genomics, we present a new randomness test based on the empirical entropy of strings and some properties of repeatability and unrepeatability of substrings of certain lengths. We give the theoretical motivations of our method and some experimental results of its application to a wide class of strings: decimal representations of real numbers, roulette outcomes, logistic maps, linear congruential generators, quantum measurements, natural language texts, and genomes. It will be evident that the evaluation of randomness resulting from our tests does not distinguish among the different sources of randomness (natural, or pseudo-casual).

Control of canine infections with Leishmania infantum (L. infantum), a major zoonotic disease in Brazil and southern Europe is becoming increasingly important due to their close proximity to humans, the increasing import of dogs from endemic regions and impact of climate change on vector spreading. Simple, rapid and reliable diagnostic tests are therefore needed to detect infected dogs. Here, we re-evaluated different serological methods for the diagnosis of canine leishmaniosis (CanL) in Croatia and Brazil. The diagnostic performance of the indirect fluorescent antibody test (IFAT) and the VetLine® Leishmania ELISA was compared with three rKLi8.3 based diagnostic test systems, the rKLi8.3 ELISA, the INgezim® Leishma CROM lateral flow test (LFT) and the VetBlot® Leishmania LineBlot. CanL symptomatic dogs were efficiently diagnosed by all tests, except the VetLine® Leishmania ELISA, which is based on whole Leishmania antigens. The advantage of rKLi8.3 was also observed in oligo-and asymptomatic dogs from Brazil and Croatia, although with reduced diagnostic efficiency compared to symptomatic dogs. Similar to IFAT and rKLi8.3 ELISA, the LFT did not cross-react with other common canine pathogens, showed a very high specificity for healthy dogs from endemic regions of both countries and did not react with healthy, vaccinated dogs in Brazil. In conclusion, sero-diagnostic tests based on the rKLi8.3 antigens are superior to whole parasite antigens and the LFT has the advantage of providing a laboratory independent, rapid and specific diagnosis of CanL.

Objectives: This paper presents a statistical review of modelling simulations for frequency and sensitivity of COVID-19 testing paradigms. Methods: We performed a review of preprints and published articles on PubMed from January 1, 2020 – March 1, 2021 using the search terms “COVID screening testing”, “COVID testing frequency”, “COVID testing frequency screening” and “SARS-CoV-2 testing frequency”.Results: Several authors’ conclusions support the claim that test frequency and test sensitivity both play a role in reducing SARS-CoV-2 transmission. We highlight the interplay between frequency of testing, test sensitivity and the speed at which test results are available in our review. Conclusions: Evidence suggests that sensitivity and frequency of testing both play a part in decreasing transmission of disease. We conclude that, overall, test sensitivity plays less of a role in reducing disease transmission in a population compared to the frequency of testing and how quickly test results are available.

Chronic gastroduodenal symptoms are prevalent worldwide, and there is a need for new diagnostic and treatment approaches. Several overlapping processes may contribute to these symptoms, including gastric dysmotility, hypersensitivity, gut-brain axis disorders, gastric outflow resistance, and duodenal inflammation. Gastric Alimetry® (Alimetry, New Zealand) is a non-invasive test for evaluating gastric function that combines body surface gastric mapping (high-resolution electrophysiology) with validated symptom profiling. Together, these complementary data streams enable important new clinical insights into gastric disorders and their symptom correlations, with emerging therapeutic implications. A comprehensive database has been established, currently comprising >2,000 Gastric Alimetry tests, including both controls and patients with various gastroduodenal disorders. From studies employing this database, this pa-per presents a systematic methodology for Gastric Alimetry test interpretation, together with an extensive supporting literature review. Reporting is grouped into four sections: Test Quality, Spectral Analysis, Symptoms, and Conclusions. This review compiles, assesses, and evaluates each of these aspects of test assessment, with discussion of relevant evidence, example cases, limitations, and areas for future work. The resultant interpretation methodology is recommended for use in clinical practice and research to assist clinicians in their use of Gastric Alimetry as a diagnostic aid, and is expected to continue to evolve with further development.

With the advent of Neural Machine Translation, the more the achievement of human-machine parity is claimed at WMT, the more we come to ask ourselves if their evaluation environment can be trusted. In this paper, we argue that the low quality of the source test set of the news track at WMT may lead to an overrated human parity claim. First of all, we report nine types of so-called technical contaminants in the data set, originated from an absence of meticulous inspection after web-crawling. Our empirical findings show that when they are corrected, about 5% of the segments that have previously achieved a human parity claim turn out to be statistically invalid. Such a tendency gets evident when the contaminated sentences are solely concerned. To the best of our knowledge, it is the first attempt to question the “source” side of the test set as a potential cause of the overclaim of human parity. We cast evidence for such phenomenon that according to sentence-level TER scores, those trivial errors change a good part of system translations. We conclude that to overlook it would be a mistake, especially when it comes to an NMT evaluation.

Vacuum pump wear is the most prevalent failure mode of the IBA Synthera® automated radiochemistry system. Rebuilding or replacing the pump causes equipment downtime and increases the radiation exposure of the service personnel. We built a dedicated test device to assess new or rebuilt pumps prior to installation, thus reducing downtime and radiation exposure during repairs. The Testbed incorporates a microprocessor that actuates the pump, valves, pressure sensor, and communicates with the user through lights, buttons, and an alphanumeric screen. The Testbed increases productivity and safety in the radiochemistry laboratory.

Today, concepts such as Emotional Education and Emotional Intelligence are recognized by many authors and researchers, emphasizing the importance of their development in all people, but especially in schools, specifically in teachers or educators and children. However, we still find many shortcomings within the schools that are needed to continue working. The aim of this study is to investigate the presence of emotional intelligence and empathy in teachers, through a sample of 42 participants. The research was conducted based on two validated and highly reliable assessment tools, called TMMS-24 and TECA. The results of the TMMS-24 indicate that a large percentage of participants have an adequate score of emotional intelligence. The results of the TECA indicate that most of the participants are in the middle, high or extremely high scores in relation to the level of empathy.

In reservoir engineering, one of the main sources of information for the characterization of reservoir and well parameters is well testing. Among the unconventional well testing methodologies, Harmonic Well Testing (HPT) is appealing from an economic standpoint because it could provide well performance and reservoir behavior monitoring without having to interrupt field production. Recorded pressure analysis is performed in the frequency domain by adopting a derivative approach similar to conventional well testing. To this end, pressure and rate data must be decomposed into harmonic components. Test interpretability can be significantly improved if pressure data are detrended prior to interpretation, filtering out non periodic events such as discontinuous production from neighboring wells and flow regime variations which did not respect the designed test periodicity. Therefore, detrending offers the possibility of overcoming the limitation of HPT applicability due to the difficulty of imposing a regularly pulsing rate for the whole test duration (typically lasting several days). This makes HPT attractive for well performance monitoring, especially in gas storage fields. In this paper, the application of different detrending methodologies to synthetic HPT pressure data generated in different reservoir and operational scenarios is presented and discussed. Moreover, a real case application is also presented.

Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this work is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

The Medi-test system we developed was motivated by the large number of resources available for the medical domain, as well as the number of tests needed in this field (during and after the medical school) for evaluation, promotion, certification, etc. Generating questions to support learning and user interactivity has been an interesting and dynamic topic in NLP since the availability of e-book curricula and e-learning platforms. Current e-learning platforms offer increased support for student evaluation, with an emphasis in exploiting automation in both test generation and evaluation. In this context, our system is able to evaluate a student’s academic performance for the medical domain. Using as input medical reference texts and supported by a specially designed medical ontology, Medi-test generates different types of questionnaires for Romanian language. The evaluation includes 4 types of questions (multiple-choice, fill in the blanks, true/false and match), can have customizable length and difficulty and can be automatically graded. A recent extension of our system also allows for the generation of tests which include images. We evaluated our system with a local testing team, but also with a set of medicine students, and user satisfaction questionnaires showed that the system can be used to enhance learning.

Identifying the SARS-CoV-2 virus has been a unique challenge for the scientific community. In this paper, we discuss a practical solution to help guide clinicians with interpretation of the probability that a positive, or negative, COVID-19 test result indicates an infected person, based on their clinical estimate of pre-test probability of infection.The authors conducted a small survey on LinkedIn to confirm that hypothesis that that the clinical pre-test probability of COVID-19 increases relative to local prevalence of disease plus patient age, known contact, and severity of symptoms. We examined results of PPA (Positive Percent Agreement, sensitivity) and NPA (Negative Percent Agreement, specificity) from 73 individual laboratory experiments for molecular tests for SARS-CoV-2 as reported to the FIND database ¹, and for selected methods in FDA EUA submissions^2,3. Authors calculated likelihood ratios to convert pre-test to post-test probability of disease and designed an online calculator to create graphics and text to report results. Despite best efforts, false positive and false negative Covid-19 test results are unavoidable^4,5. A positive or negative test result from one laboratory has a different probability for the presence of disease than the same result from another laboratory. Likelihood ratios and confidence intervals can convert the physician or other healthcare professional’s clinical estimate of pre-test probability to post-test probability of disease. Ranges of probabilities differ depending on proven method PPA and NPA in each laboratory. We recommend that laboratories verify PPA and NPA and utilize a the “Clinician’s Probability Calculator” to verify acceptable test performance and create reports to help guide clinicians with estimation of post-test probability of COVID-19.

Theory of the Thermal Response Testing (TRT) is a well-known part of sizing process of the geothermal exchange system. Multiple parameters influence accuracy of effective ground thermal conductivity measurement; like testing time, variable power, climate interferences, groundwater effect etc. To improve accuracy of the TRT we introduced procedure to additionally analyze falloff temperature decline after power test. Method is based on a premise of analogy between TRT and petroleum well testing, since origin of both procedures lies in diffusivity equation with solutions for heat conduction or pressure analysis during radial flow. Applying pressure build-up test interpretation technique to the borehole heat exchanger testing, greater accuracy could be achieved since ground conductivity could be obtained from this period. Analysis was conducted on coaxial exchanger with five different power steps, and with both direct and reverse flow regime. Each test was set with 96hr of a classical TRT, followed by 96hr of temperature decline, making it almost 2000 hours of cumulative borehole testing. Results showed that ground conductivity value could vary as much as 25% depending on test time, seasonal period and power fluctuations while thermal conductivity obtained from a falloff period gives more stable values with only 10% value variation.

In order to reduce the silique shattering loss of rapeseed mechanical harvesting process, based on the state of force on the silique during rapeseed harvesting reel branch, Ningza 1810, Zhenyou 8 and Fengyou 306 were used as research objects, and the experimental research on the factors affecting rapeseed siliques shattering was carried out using the swing impact method. The experimental analysis showed that: rapeseed varieties, silique moisture content, silique growth position, collision material, impact speed, force position and other factors had significant effects on silique shattering. The impact velocity was less than 1.5m·s-1, the difference on the effect of each factor on pod-shattering was not significant, it was not easy to shatter when the moisture content of rapeseed silique was higher. The impact resistance of the front side of rapeseed was 2 to 4 times that of the bonding surface of rapeseed petals, the shattering rate of the top rapeseed silique was twice that of the bottom siliques, when siliques were supported, they were more likely to shatter under external forces than when they were unsupported. The experimental study of the mechanical properties of rapeseed siliques was carried out using the impending fracture method, the experimental analyses showed that the support position and force position of the silique, the loading speed and the growth position of the silique had a significant effect on the mechanical properties of the silique. The maximum cracking force was higher and bending strength was stronger when the body of the silique was supported, which the range of the maximum cracking force were 3.05N to 4.16N, and the bending strength range were 8.48 MPa to 11.57 MPa. The maximum cracking force and bending strength of the silique was stronger when the front side of the silique petal was pressurized than when the bonding surface of the petal was pressurized. Based on Pearson's correlation and grey correlation analysis, the morphological characteristics of rapeseed siliques were ranked in order of their influence on the performance of siliques in terms of the angle between silique and stalk, stalk diameter, petal thickness, beak length, silique thickness, silique width and silique length. This study can be used as a reference for the design and optimization of the rapeseed harvesting reel branch mechanism and the selection of machine harvestable rapeseed varieties.

Sweetness drives consumption of added sugars, so understanding how individuals differ is important for developing strategies to lower sugar intake. However, methods to assess hedonic response to sweetness vary, making results across studies difficult to integrate. We compared methods to measure optimal sucrose concentration in 21 healthy adults (1) using paired-comparison preference tracking vs. ratings of liking, (2) with participants in the laboratory vs. at home, and (3) using aqueous solutions vs. vanilla milk. Tests were replicated on separate days to assess test-retest reliability. Test-retest reliability was similar between laboratory and home testing, but tended to be better for vanilla milk and preference tracking. Optimal sucrose concentration was virtually identical between laboratory and home, slightly lower when estimated via preference tracking, and about 50% lower in vanilla milk. However, individual optimal sucrose concentration correlated strongly between Methods, test Locations, and Stimuli. More than 50% of the variability in optimal sucrose concentration could be attributed to consistent differences among individuals while much less variability was attributable to differences in Methods, test Locations or Stimuli. These results demonstrate convergent validity between measures of preference and liking, support testing at home to lower participant burden, and suggest that aqueous solutions can be useful proxies for some commonly consumed beverages for measuring individual differences.

A quantum theory of gravity is among the most pursued goals in physics. I present a definitive and direct experimental proof that refutes the widely believed hypothesis of quantum gravity. The detections of astrophysical gravitational waves (GW) are inferred from the differential oscillations of suspended mirrors of optical interferometers like the aLIGO detectors. If gravity is indeed quantized, then the average energy $\bar{E}$ in the minute oscillations of the mirrors, at a frequency $\nu$, corresponds to the absorption of an integer number $N$ gravitational quanta with total energy $E_{gw}=Nh\nu$. The coherent and coincident detections across large separations of detectors, and also the constraint of the equivalence principle, dictate that the average number of quanta $\bar{N}$ forcing the oscillations obeys $\bar{N}\gg 1$, or $1/\sqrt{\bar{N}}\ll 1$. However, the average energy $\bar{E}$ in the differential oscillations is smaller than the energy of a single quantum of GW radiation at the detected astrophysical GW frequencies. This startling finding implies that $\bar{N} <1$, which is physically impossible if gravity is quantized. This singular contradiction refutes the long-held hypothesis that gravity is quantized.

Background: Diet is a risk factor for gestational diabetes mellitus (GDM). There are few studies on women´s diet and glucose tolerance test (GTT) results. Objective: To evaluate the relationship between previous diet and the number of abnormal values on the diagnostic GTT in women with GDM. We hypothesized there would be an inverse relation between antioxidant micronutrient consumption and the number of abnormal GTT values. Methods: This cross-sectional study included 60 women diagnosed with GDM (2-hours, 75g-GTT). Shortly after diagnosis, participants answered a validated food frequency questionnaire to assess food consumption in the last 6 months. Mann-Whitney´s test was used to compare the dietary intake of participants with one (group 1) versus two-three (group 2) abnormal GTT values. Results: Participant characteristics were similar. There were no significant differences between groups in median intake of total calories, carbohydrates, lipids and proteins. Participants in group 1 had significantly higher intakes of fiber (11.9 vs. 11.0 g/day p= 0.049), vitamin D (40.6 vs. 40.4 mcg/day p= 0.049) and vitamin C (180.0 vs. 151.0 mg/day p= 0.008) than those in group 2. Conclusion: Results suggest a possible association between consumption of fiber and some antioxidant micronutrients and GDM severity at the time of diagnosis.

This study is aimed to point out the possible application of the Enzyme-Linked ImmunoSorbent Assay (ELISA) test on table olives. Because olives, like many other foods, are not free from mycotoxin contamination, the main focus of this work was assessing the presence or absence of aflatoxins and ochratoxin A. The work was carried out in two phases. In the first phase, tests were carried out on commercial olives to assess the efficacy of the method and the kit (Veratox® 'Neogen' and AgraQuant® 'Romer Labs') by comparing them with the Liquid Chromatography coupled to a mass-mass spectrometer (LC-MS/MS); in order to understand if there were any interferences in antigen-antibody recognition; subsequently, mycotoxins were inoculated on the same samples with a known quantity, in order to assess the concentrations obtained and compare them to the expected ones. The second step involved modifying the method, so to improve the recovery of inoculated mycotoxins in the samples under study. Afterwards we evaluated the presence of mycotoxins in table olives supplied in the project. The results showed the effectiveness of the ELISA test, especially in the mycotoxin recovery phase. Indeed, after the modification of the mycotoxin extraction method, recoveries increased from 55% to over 70% for aflatoxins, and from 40% to over 55% for ochratoxin A. When analysing the samples provided by the above-mentioned company, the results showed some false positives, in particular in relation to ochratoxin A ’s analysis, mainly related to the first sample submission. Taking this into account, the ELISA test can be considered as an initial screening method applicable as a control programme for the evaluation of mycotoxins in olives which helps by saving time and costs. It should always be kept in mind that, if positive values should emerge, the LC-MS/MS analysis should be carried out.

An increasingly frail population in nursing homes accentuates the need for high quality care at the end of life and better access to palliative care in this context. Implementation of palliative care and its outcomes can be monitored by using quality indicators. Therefore, we developed a quality indicator set for palliative care in nursing homes and a tailored measurement procedure using a mixed-methods design. We developed the instrument in three phases: 1) literature search, 2) interviews with experts and 3) indicator and measurement selection by expert consensus (RAND/UCLA). Second, we pilot tested and evaluated the instrument in nine nursing homes in Flanders, Belgium. After identifying 26 indicators in the literature and expert interviews, 19 of them were selected through expert consensus. Setting-specific themes were advance care planning, autonomy and communication with family. The quantitative and qualitative analyses showed the indicators were measurable, had good preliminary face validity and discriminative power and were considered useful in terms of quality monitoring according to the caregivers. The quality indicators can be used in a large implementation study and process evaluation in order to achieve continuous monitoring of the access to palliative care for all residents in nursing homes.

Kaempferia parviflora Wall. ex Baker (KP), Krachaidam in Thai or Thai ginseng, is an herbal medicine that has many potential pharmacological effects. This study focused on the oral glucose tolerance test and pharmacokinetic study in healthy volunteers administered with KP extract (90 and 180 mg/day, placebo). The oral glucose tolerance tests were performed at baselines and 28-days of administration. The pharmacokinetics were determined after a single dose administration of the tested products using 3,5,7,3,4-pentamethoxyflavone (PMF) and 5,7,4-trimethoxylfavone (TMF) as markers. The results showed that glucose metabolism via oral glucose tolerance test was not affected by KP extract. The results of pharmacokinetics study revealed that only TMF and PMF, but not DMF levels could be detected in human blood. The given doses of KP extract at 90 and 180 mg/day showed a linear dose-relationship of blood PMF concentration whereas blood TMF was detected only at high given dose (180 mg/day). The half-lives of PMF and TMF were 2–3 h. The Cmax, AUC and Tmax values of PMF and TMF estimated for the 180 mg/day dose were 85.3711.31, 73.2329.93 mg/ml; 291.8948.23, 412.20203.69 mg.h/ml; and 3.890.37, 4.500.96 h, respectively. PMF was quickly eliminated with higher Ke and Cl than TMF at the dose of 180 mg/day of KP extract. In conclusion, the results demonstrated that KP extract had no effect on glucose tolerance test. In addition, this is the first demonstration of the pharmacokinetic parameters of methoxyflavones of KP extract in healthy volunteers in a phase I study in drug development. The data suggest the safety of the KP extract and will be of benefit for further clinical trials using KP extract as food and sport supplements as well as a drug in health product development.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

Oriented strand board (OSB) panels are widely marketed for several applications, from building to packaging. The manufacturing of poplar OSB started recently in Northern Italy representing a relevant innovation in the sector since this product is usually made of coniferous wood. The thermal treatment is widely used for reducing the hygroscopicity of wood-based products, nonetheless it influences the mechanical behavior and degrades the main components of wood, which can affect their finishing. Therefore, it is important to know the properties of the treated surfaces. To this purpose, in this study a lot of OSB panels, made of poplar wood, 15 mm thick and with a density of 590 kg/m³, were thermally treated under vacuum conditions at 190 °C for 2 h and then subjected to accelerated weathering. The changes in color and in wettability due to treatment and accelerated weathering were studied. The thermal treatment determined a significant darkening of the color; the accelerated weathering darkened the untreated surfaces and, on the opposite, lightened the thermo-treated surfaces. The wettability decreased after thermal treatment and increased after weathering, more evidently in treated panels. Overall, this study improves the knowledge about the behavior of the surface of thermo-treated poplar OSB, which is relevant for the industrial coating of this product.

Conceal carry weapon (CCW) laws have generated a great deal of public discussion in the past decades, but little social science attention. Scholarly worked on the topic has been focused on finding potential effects of such laws on crime and victimization; little has attempted to explain the trends behind the adoption of the laws. This paper attempts to fill that gap by testing a series of hypotheses grounded in minority threat approaches. Our paper examines whether or not changes in the racial and ethnic composition of a county predict the voting outcome of Missouri’s 1999 conceal-carry referendum. Findings fail to reject the null hypothesis and show the best predictor of the vote within a county was how that county voted in the 2000 Presidential election.

The study of ecosystems, both natural and artificial, has historically been mediated by population dynamics theories. In this framework, quantifying population numbers and related variables (associated with metabolism or biological-environmental interactions) plays a central role in measuring and predicting system-level properties. As we move towards advanced technological engineering of cells and organisms, the possibility of bioengineering ecosystems (from the gut microbiome to wildlands) opens several questions that will require quantitative models to find answers. Here, we present a comprehensive survey of quantitative modelling approaches for managing three kinds of synthetic ecosystems, sharing the presence of engineered strains. These include test tube examples of ecosystems hosting a relatively low number of interacting species, mesoscale closed ecosystems (or ecospheres), and macro-scale, engineered ecosystems. The potential outcomes of synthetic ecosystem designs and their limits will be relevant to different disciplines, including biomedical engineering, astrobiology, space exploration and fighting climate change impacts on endangered ecosystems. We propose a space of possible ecosystems that captures this broad range of scenarios and a tentative road map for open problems and further exploration.

This paper presents a statistical approach to identify the underlying roughness characteristics in synthetic aperture radar (SAR) intensity data. The physical modeling of this kind of data allows the use of the Gamma distribution in the presence of fully-developed speckle, i.e., when there are infinitely many independent backscatterers per resolution cell, and none dominates the return. Such areas are often called ``homogeneous'' or ``textureless'' regions. The GI0 distribution is also a widely accepted law for heterogeneous and extremely heterogeneous regions, i.e., areas where the fully-developed speckle hypotheses do not hold. We propose three test statistics to distinguish between homogeneous and inhomogeneous regions, i.e., between gamma and GI0 distributed data, both with a known number of looks. The first test statistic uses a bootstrapped non-parametric estimator of Shannon entropy, providing a robust assessment in uncertain distributional assumptions. The second test uses the classical coefficient of variation (CV). The third test uses an alternative form of estimating the CV based on the ratio of the mean absolute deviation from the median to the median. We apply our test statistic to create maps of \(p\)-values for the homogeneity hypothesis. Finally, we show that our proposal, the entropy-based test, outperforms existing methods, such as the classical CV and its alternative variant, in identifying heterogeneity when applied to both simulated and actual data.

Pigs are used as laboratory animals in preclinical studies on medical devices for cardiac surgery. On the one hand, the anatomy of the cardiovascular system of these animals has been well studied and acknowledged suitable for use and testing of new cardiovascular devices developed for humans. On the other hand, there are no morphometric characteristics of the aortic root and other parts of it in pigs with different weights. This can lead to difficulties in the work of researchers and even result in the death of experimental animals due to the discrepancy in the size of the implantable devices. Thus, such information is essential to improve the efficiency of surgical technologies used in the correction of aortic pathologies in its various sections. The purpose of our research is to study the anatomy of the aorta in mini-pigs, and to assess whether the size, age, and sex of animals affect the size of the main structures in their aorta. In addition, we attempted to compare the results obtained by the method of transesophageal echocardiography (TEE) and angiography. We studied 28 laboratory mini-pigs weighing from 40 to 105 kg, and then we compared our results with other studies and did not find any relationship between the external somatometric characteristics of animals and the size of their aorta. Each animal has an individual anatomy, so they are to be examined in terms of preoperative planning by any available method - echocardiography, angiography or multispiral computed tomography (MRI).

Our main goal is here to make a comparative analysis between the well-known MOND theory and a more recent model called κ-model. An additional connection, between the κ-model and two other novel MOND-type theories: Newtonian Fractional-Dimension Gravity (NFDG) and Refracted Gravity (RG), is likewise presented. All these models are built to overtake the DM paradigm, or at least to strongly reduce the dark matter content. Whereas they rely on different formalisms, however, all four seem to suggest that the universal parameter, a0, appearing in MOND theory could intrinsically be correlated to either the sole baryonic mean mass density (RG and κ-model) and/or to the dimension of the object under consideration (NFDG and κ-model). We could then confer to the parameter a0 a more flexible status of multiscale parameter, as required to explain the dynamics together in galaxies and in galaxy clusters. Eventually, the conformal gravity theory (CFT) also seems to have some remote link with the κ-model, even though the first one is an extension of general relativity, and the second one is Newtonian in essence. The κ-model has been tested on a small sample of spiral galaxies and in galaxy clusters. Now we test this model on a large sample of galaxies issued from the SPARC database.

In recent decades, low-yielding seismic devices based on the use of friction dampers have emerged as an excellent solution for the development of building structures with improved reparability and resilience. Achieving an optimal design for such low-yielding seismic devices requires precise control of bolt preloading levels and predictability of the friction coefficient (CoF) between the damper interfaces. While various types of friction devices exist, capable of providing significant energy dissipation, ongoing research is focused on the development of novel friction materials that exhibit a stable hysteretic response, high CoF values, minimal differences between static and dynamic CoF, and predictable slip resistance. In this context, an experimental campaign was conducted at the STRENGTH Laboratory of the University of Salerno to evaluate the behaviour of new friction shims employing specially developed metal alloys. Specifically, the influence of the characteristics of the contact surfaces in the sliding area on the behaviour and performance of the friction device was analysed. The tests followed the loading protocol recommended by EN12159 for seismic device qualification. Monitored parameters included preloading force values and the evolution of slip resistance. The friction value was determined, along with its degradation over time. Finally, the material's performance in terms of hysteretic behaviour was assessed, providing a comparison of the tested specimens in terms of slip force degradation and energy dissipation capacity.

The importance of performance excellence and operator’s safety is fundamental not only when operators perform repetitive and controlled industrial tasks, but also in case of abrupt gestures due to inattention and unexpected circumstances. Since optical systems work at too low frequencies and they are not able to detect gestures as early as possible, combining the use of wearable magneto-inertial measurement units (MIMUs) with the adoption of deep learning techniques can be useful to instruct the machine about human motion. To improve the initial training phase of neural networks for high classification performance, gestures repeatability over time has to be verified. Since test-retest approach has been poorly applied based on MIMUs signals in a context of human-machine interaction, the aim of this work was to evaluate the repeatability of pick-and-place gestures composed of both normal and abrupt movements. Overall, results demonstrated an excellent test-retest repeatability for normal movements and a fair-to-good test-retest repeatability for abrupt movements. Moreover whereas the reduction of time between test and retest sessions increased repeatability indices.. In detail, results of the test suggested how to improve the reinforcement learning for the identification of gestures onset, whereas results of the retest gave important information about the time necessary to retrain the network.

The fixed stroke fatigue test can not simulate the real load condition of the landing gear, and the variable stroke fatigue test has increasingly become the mainstream. A modular test device for fatigue test for aircraft landing gears was designed, the automatic control of the buffer stroke was realized with ectopic displacement control technology effectively, the horizontal loading cylinder could follow the wheel axis actively with the displacement active control technology, follow-up loading along the vertical direction was realized through constructing a polar coordinate system and making the load line automatic alignment, a split-type dummy wheel was designed to improve the loading accuracy, a booster cylinder was designed to realize the control loading of high pressure combined with the hydraulic control system. The test shows that the technical scheme meets the design requirements, and the fatigue test was completed successfully. The device for landing gear variable stroke fatigue testing can be applied to other landing gear static / fatigue tests.

Graphically-rich applications such as games are ubiquitous with attractive visual effects of Graphical User Interface (GUI) that offers a bridge between software applications and end-users. However, various types of graphical glitches may arise from such GUI complexity and have become one of the main component of software compatibility issues. Our study on bug reports from game development teams in NetEase Inc. indicates that graphical glitches frequently occur during the GUI rendering and severely degrade the quality of graphically-rich applications such as video games. Existing automated testing techniques for such applications focus mainly on generating various GUI test sequences and check whether the test sequences can cause crashes. These techniques require constant human attention to captures non-crashing bugs such as bugs causing graphical glitches. In this paper, we present the first step in automating the test oracle for detecting non-crashing bugs in graphically-rich applications. Specifically, we propose GLIB based on a code-based data augmentation technique to detect game GUI glitches. We perform an evaluation of GLIB on 20 real-world game apps (with bug reports available) and the result shows that GLIB can achieve 100\% precision and 99.5\% recall in detecting non-crashing bugs such as game GUI glitches. Practical application of GLIB on another 14 real-world games (without bug reports) further demonstrates that GLIB can effectively uncover GUI glitches, with 48 of 53 bugs reported by GLIB having been confirmed and fixed so far.

This paper studies the goodness of fit test for the bivariate Hermite distribution. Specifically, we propose and study a Cramér-von Mises-type test based on the empirical probability generation function. The bootstrap can be used to consistently estimate the null distribution of the test statistics. A simulation study investigates the goodness of the bootstrap approach for finite sample sizes.

Effective maintenance of railways requires a comprehensive assessment of the actual condition of the construction materials involved. In this regard, Ground-Penetrating Radar (GPR) stands as a viable alternative to the invasive and time-consuming traditional techniques for the inspection of these infrastructures. This work reports the experimental activities carried out on a test-site area within a railway depot in Rome, Italy. Specifically, a 30 m-long railway section was divided into 10 sub-sections reproducing different various physical and structural conditions of the track-bed. In more detail, combinations of varying scenarios of fragmentation and fouling of the ballast were reproduced. The set-up was then investigated using different multi-frequency GPR horn antenna systems. The effects of the different physical conditions of ballast on the electromagnetic response of the material were analysed for each scenario using time- and frequency-domain signal processing techniques. Parallel to this, modelling was provided to estimate fouling content. Interpretation of results has proven the viability of the GPR method in detecting signs of decay at the network level, thereby proving this technique to be worthy for implementation in asset management systems.

In this study, an optimization of the first blade in new test rig presented. Blade tuning is conducted using 3D geometrical parameters. Sweep and dihedral play an essential role in this study. Compressor characteristics and blades vibrational behavior are the main objective of the evaluation. Here, the attachments are designed to isolate blade dynamics from Disk. So, the Vibrational behaviors of the one's blade are tuned based on the self-excited and forced vibration phenomenon. Using a semi analytical MATLAB code instability conditions are satisfied. The code takes advantages of whitehead and force response theory to predict classically and stall flutter speeds. Beside, Forced vibrations instability is controlled using a theory presented by Campbell. Aerodynamics of new blade geometry determined using multistage simulations Computational fluid dynamics (CFD) software. Numerical results show increasing performance near the surge line and working interval along with increasing mass flow.

Dispersion tests based on the second order component of smooth test statistics are related to Fisher’s Index of Dispersion test, used for testing for the Poisson distribution when there are no covariates present. Such tests have been recommended in [1] to test for the Poisson distribution when covariates are present. The modified Borel-Tanner (MBT) distribution seems suited to data with extra zeroes, a monotonic decline in counts and longer tails. Here we recommend a dispersion test for the MBT distribution for both when covariates are absent and when they are present.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

The demonstration of compliance of rolling stock against disturbance limits for railway signaling, and in particular track circuits, is subject to a large deal of variability, caused by the diverse values of the electrical parameters of the railway line and resulting transfer functions, as well as operating conditions of rolling stock during tests. Instrumental uncertainty is evaluated with a Type B approach and shown to be much less than the experimental variability. Repeated test runs in acceleration, coasting, cruising, braking conditions are considered, deriving both max-hold (spread) and sample dispersion curves compared to the respective mean values (Type A approach to the evaluation of uncertainty). The major source of variability affecting a significant portion of the spectrum is caused by the superposed oscillations of the onboard LC filter, for which different choices of the transformation window duration are discussed. The test runs and the acquired data covered overall 1 day of tests along about 300 km of the Italian 3 kV DC railway network.

A self-propelled electric tea seed-planter is designed to address the lack of tea seed seeding equipment, low seeding efficiency, and poor seeding uniformity. Based on the physical characteristics of the tea seeds and the agronomic requirements of tea planting, the key structure of the planter is designed, and the structural parameters are determined. The motor and battery configurations are determined by calculating the power consumption of the entire machine. In a field experiment, the driving gear (A), ditching depth (B), and planting gear position (C) are used as test factors, and the acceptance index (AI), replay index (RI) and leakage index (LI) are used as test indexes. The test results showed that the driving speed and planting gear position significantly affect the acceptance index, replay, and leakage index, whereas the ditching depth has little effect on the performance indexes. When the driving speed was medium, ditching depth was 30 mm, and planting gear position was in the third gear, the corresponding acceptance index was 87.22%, the replay index was 8.89%, and the leakage index was 3.89%. The test prototype has a good working quality and can provide theoretical guidance for production practices.

Disposable absorbent hygiene products have evolved for superior performance, enhancing the convenience of daily lives. Yet the use of disposable hygiene pads has brought safety concerns on chemical exposure, and significant efforts have been made to assess the potential risks associated with use of hygiene pads. This article intends to overview the safety assessment framework of diapers and feminine pads, which includes hazard identification, hazard characterization, exposure assessment, risk characterization, and postmarket risk management. Risk assessment of various constituents are reviewed for quantification methods and conservative estimation of exposure parameters. By reviewing the up-to-date considerations in risk assessment, we aim to provide insightful discussion on safety evaluation of current versions of disposable absorbent products. More clinical testing and postmarket surveillance are needed for continuous monitoring of potential health impacts of advanced products and constituents.

In modern Commercial Off-The-Shelf (COTS) multicore systems, cores can produce several simultaneous memory requests. The processing of such requests over the memory controller negatively impacts the interference delay triggered by running parallel tasks on the platform. In this paper, we propose a software-based testing approach for analyzing memory interference delay, when cores are exposed to extensive read/write requests that access in parallel their Cache Coherent Interconnect. The hardware targeted in this work is the well-known LayerScape QorIQ LS2085A, which can be approached as a potential successor to the Freescale QorIQ P4080. The test analysis was conducted based on a bare-metal operating system that we developed to guarantee a deterministic execution environment at all time points. Our testing was accomplished using a set of carefully designed synthetic benchmarks as well as TACLeBench benchmarks.

The Combined Elevation Test (CET) is a musculoskeletal screening technique (MST) replicates the streamline position in swimming and is commonly used in various sports. Although the CET is widely used, no normative data exist within an adolescent population. Therefore, the purpose of this study was to develop a normative data set for the CET within an adolescent population and to evaluate the influence various demographic and anthropometric variables. Data was collected for 416 participants aged between 8 and 18 years old. Age and arm span showed a significant correlation with CET scores (arm span r_s (105) = .478, p = .000, age r_s (416) = .238 p = .000). Regression analysis further quantified the influence of arm span and age on CET scores accounting for 23.1% and 5.3% of variability respectively. These results can be used as a reference point for clinicians and coaches who are using the CET within their assessment.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

The idea that the Earth system self-regulates in a habitable state was proposed in the 1970s by James Lovelock, who conjectured that life plays a self-regulatory role on a planetary-level scale. A formal approach to such hypothesis was presented afterwards under a toy model known as the Daisyworld. The model showed how such life-geosphere homeostasis was an emergent property of the system, where two species with different properties adjusted their populations to the changing external environment. So far, this ideal world exists only as a mathematical or computational construct, but it would be desirable to have a real, biological implementation of Lovelock's picture beyond our one Biosphere. Inspired in the exploration of synthetic ecosystems using genetic engineering and recent cell factory designs, here we propose such a living, microbial Daisyworld. This is based on a synthetic microbial ecosystem using pH as the external, abiotic control parameter. Several case studies are considering, including two, three and multiple species assemblies. Despite that oscillatory dynamics and chaos emerge in the latter case, it is shown that global regulation is also achieved in most cases as species diversity increases. The alternative implementations and their implications of this model in other synthetic biology scenarios, including ecosystem engineering, are outlined.

Purpose: To investigate trabeculopuncture (TP) for predicting the outcome of ab interno trabeculectomy (AIT). AIT is an effective, low-risk procedure for open angle glaucoma. Despite widespread utilization, it fails in patients with an unidentified distal outflow resistance. Methods: We bisected 81 enucleated porcine eyes and perfused them for 72 hours. They were assigned to two groups: trial (n=42) and control (n=39). Intraocular pressure (IOP) was measured continuously. At 24 hours, four YAG-laser trabeculopunctures on the nasal trabecular meshwork were performed, followed by a 180° AIT at the same site at 48 hours. Eyes were divided into TP and AIT responders and non-responders; the proportion of TP responders between both AIT groups was compared. Results: Both post-TP and post-AIT IOPs were lower than baseline IOP (p=0.015 and p<0.01, respectively). The success rates of TP and AIT were 69% and 85.7%, respectively. The proportion of TP responders among AIT responders was greater than that of AIT non-responders (p<0.01). Sensitivity and specificity values of TP as predictive test for AIT success were 77.7% and 83.3%, respectively. The positive and negative predictive values were 96.6% and 38.5%, respectively. Conclusion: A 10% reduction in IOP after TP can be used as predictor for the success (>20% IOP decrease) of 180° AIT in porcine eyes.

In general, the stone pagoda structures with discontinuous surfaces are vulnerable to lateral forces and are severely damaged by earthquakes. After the Gyeongju earthquake in 2016 and the Pohang earthquake in 2017, the earthquakes damaged numerous stone pagoda structures due to slippage, rotation and the separation of stacked stone. To evaluate seismic resistance of masonry stone pagoda structure, we analyzed the seismic behavior of stone pagoda structure using shaking table test. Shaking frequency, permanent displacement, maximum acceleration, rocking, and sliding were assessed. Responses to simulations of the Bingol, Gyeongju, and Pohang earthquakes based on Korean seismic design standard (KDS 41 17 00) were analyzed for return periods of 1,000 and 2,400 years. We found that the type of stylobate affected the seismic resistance of stone pagoda structure. When the stylobates were stiff, seismic energy was transferred from lower to upper regions of the stone pagoda, which mainly resulted in deformation of the upper region. When the stylobates were weak, earthquake energy was absorbed in the lower regions; this was associated with large stylobate deformations. The lower part of tower body was mainly affected by rocking, because the structural members were slender. The higher part of the stone pagoda was mainly affected by sliding, because the load and contact area decreased with height.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil &amp; gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

The aim of this document is to present how the interpretation of the RVM (Recovery Voltage Measurement) test can be improved through the use of a Debye equivalent circuit. As it is described in the literature the interpretation of the RVM test requires expertise and if the transformer presents a high interfacial polarization it is not possible to diagnose it in detail. Debye model is proposed in this work for enhancing RVM interpretation. This model is based on an electrical circuit that includes basic R-L-C components, that allows two interesting features: on one hand, isolation physical effects can be separately represented and, on the other, the values of the R-C components can be calculated from the RVM response (L components are not used in this work as long as no magnetic field effects are taken into account). Thus, the different isolation effects that are indistinguishable merged in the RVM transient response can be split into different R-C branches, each one corresponding with a single (not merged) isolation effect. Finally, several case studies are presented, in which it is correlated a dielectric oil treatment carried out and the equivalent circuit changes.

The textile sector is responsible for a number of environmental impacts. Due to the in-creasing quantities of textiles, their share is rising and a trend reversal from a linear to a circular textile chain is needed. This article presents the background, methodological approach and results of a participatory textile development model. In the commercial B2B sector, three textile prototypes were developed together with users and trialled over several months in three application areas. Textile development took into account the requirements of fibre regeneration in the product design and focused on innova-tive chemical recycling solutions. The three sustainably aligned textiles were subject-ed to spectroscopic and textile-technological tests. Screening life cycle assessments an-alysed their environmental profile and compared it with reference textiles that are used as standard. Overall, it is clear that the three textiles can match conventional ref-erence textiles in terms of quality and have considerable environmental benefits com-pared to the reference textiles. The user survey did identify concerns about a high arti-ficial fibre content, although a general rejection of recycled fibres was not observed. The results show that a transformation is possible, but must start with the fibre com-position; recycling, on the other hand, is of minor importance.

This study aims to construct simple devices to ascertain the concentrations of ammonium (NH4+) and nitrate (NO3-). The device structure comprises a visible and near-infrared absorption meas-urement room, along with an RGB (red, green, and blue) absorption measurement room, con-stituting the two measuring rooms. Both the measurement rooms are equipped with light sources and detectors configured to operate in opposed or thru-beam modes. A tiny processor is utilized for processing the measurements, with an algorithm implemented within its memory. During the algorithm development phase, ranges for measuring the quantity of nutrients were categorized using a discriminant analysis approach. Thirty percent of the soil sample data were utilized as verification data, while the remaining 70 percent served as training data. Nutrient content values from reliable measuring instruments were incorporated into all datasets. Discriminant analysis was employed to classify the amount of NH4+ into five ranges based on the test results. When tested with soil samples, the accuracy was 66.13% compared to the reference value of a reliable measuring device. Similarly, NO3- was classified into four ranges with an accuracy of 81% com-pared to the reference value of a reliable measuring device.

Minerals are the chief constituents of rocks and they have varied properties such as surface area, surface charge, site densities etc. Hence, numerous interactions are bound to occur in the reservoir during rock-fluids (i.e., rock, crude oil and brine) interactions. This study seeks to assess the role of mineralogical composition on the wettability of Sandstone Rocks (SR) and Mineral Mixture (MM) using both Surface Complexation Modelling (SCM) and flotation test. From the considered sandstone rocks, both the experimental results and its simulated counterpart revealed that, the SR were preferentially hydrophilic. For the MM, when the mass fraction of the hydrophobic mineral was increased, the affinity of the MM became slightly hydrophobic and vice-versa. For the dominant sandstone reservoir rock minerals with predominantly negatively charged surfaces, negligible oil adsorption took place due the interfacial repulsive forces at the oil-brine and mineral-brine interfaces. For the MM with low calcite content, the wetting preference was influenced by the mineral with prominent surface area. Our developed model portrayed that the main mechanism for oil adhesion onto sandstone minerals was divalent cations bridging. Nonetheless, adhesion of carboxylate (&gt;COO-) onto the illite, montmorillonite and calcite sites also took place with the latter being more pronounced.

The aim of this study was to develop and assess the reliability and validity of an innovative field test that measures lower limb explosive power in basketball players (i.e., alactic anaerobic capacity) for the dominant and non-dominant leg. The test examines the performance of vertical, horizontal, and combined movements while holding the ball – similar to penetration of the basket or layup. Such capabilities are required throughout basketball practice and games, combined with upper and lower body coordination. The study included 22 male basketball players, ages 16-18, members of an elite youth league team in Israel. To assess validity, the participants performed the test for each leg, followed by nine standardized tests that were developed for a range of ball games, including basketball. To assess reliability, the participants performed a retest of the unique test 72-hours later. Our findings indicate the validity and reliability of the proposed anaerobic alactic field test for basketball players, for the dominant and non-dominant leg. Moreover, strong correlations were seen between the novel test and the standardized tests, with a high correlation for horizontal explosive power (0.5<r<0.7), a very high correlation for vertical explosive power (0.7<r<0.9), and a nearly perfect correlation for the two combined (r>0.9). In conclusion, this unique field test for basketball players could assist coaches in developing and applying optimal training programs and game plans, for players individually, and for the team as a whole. As the test measures each leg separately, it could also offer an assessment tool following players’ injuries.

Categorical data analysis of 2 x 2 contingency tables is extremely common, not least because they provide odds and risk ratio statistics in medical research. The χ2 test is most often used, although some researchers use the likelihood ratio test (LRT). Does it matter which test is used? This paper argues that the LRT rather than the χ2 test should be used when we are interested in testing whether two variables are independent, as is typically the case. In contrast, the χ2 test should be reserved for where the data appear to match too closely a particular hypothesis (e.g. the null hypothesis), as may occur in the investigation of data integrity. Finally, it is argued that the evidential approach provides a consistent and coherent way in which tests can be made for each of these situations.

With the wide application of flow sensor, their reliability under extreme conditions has been concerned in recent years. The reliability of a Micro Electro Mechanical Systems flow sensor under temperature (Ts) is researched in this paper. Firstly, the Step-stress accelerated degradation test is designed. Because this flow sensor consists flow sensor chip and signal processing system, the accelerated degradation testing is implemented, respectively. While the results show that the biggest drift is 3.15% for flow sensor chips with 150℃ conditions, and 32.91% for this flowmeter. By analysis, it could be found that the attenuation of the signal processing system is significant to the degeneration of this flowmeter. The minimum drift of the signal processing system accounts for 82.01% of this flowmeter. Secondly, using the Coffin-Manson model, the relationship between cycle-index and Ts is established. And the lifetime with different Ts is estimated by the Arrhenius model. In addition, the Weibull distribution is applied to evaluate the lifetime distribution. Finally, the reliability function of the Weibull distribution is demonstrated, and the survival rate within one year is 87.69% with 85℃ conditions. Thus, by the application of accelerated degradation testing, the acquired results are innovative and original. This research illustrates the reliability research, which provides a relational database for the application of this flow sensor.

Self-adaptive systems are capable of reconfiguring themselves while in use to reduce the risks forced by environments for which they may not have been specifically designed. Run-time validation techniques are required because complex Self-adaptive systems must consistently offer acceptable behavior for important services. The run-time testing can offer further confidence that a Self-adaptive system will continue to act as intended even when operating in unknowable circumstances. This article introduces an evolutionary framework that supports adaptive testing for Self-adaptive systems. To ensure that the adaptive systems continue to operate following its requirements and that both test plans and test cases continuously stay relevant to shifting operational conditions. The proposed approach using the SPEA2 algorithm facilitates both the execution and adaptation of run-time testing operations.

Medical tests' cost-effectiveness analysis reveals a strong correlation between their accuracy and analysis results. Theoretically, we provide two lower bounds that medical tests' accuracy must exceed to be considered cost-effective. Theoretically, we provide two lower bounds that the accuracy of medical tests meeting cost-effectiveness must exceed. First, medical tests' accuracy should surpass the lower bound of matching requirements for each patient to receive the most appropriate intervention based on their test results. Second, the overall lower limit should be exceeded for the medical testing to be cost-effective for the patients as a whole. Furthermore, the conclusions from this model also provide an economic explanation for the under-diagnosis of rare diseases and the challenges faced in implementing precision medicine for minority patients. A numerical simulation example validates the conclusions of this paper.

This paper considers the application of two selected algorithms (Cuckoo Search CS, Firefly Algorithm FA) to determine and maximize the reliability of a two complex system known from the literature. This system operates with resource constraints. In addition, several classical methods for determining the reliability of systems have been applied. Although the CS algorithm is known for its effectiveness as it uses the Lévy flight, for the presented optimization tasks the FA firefly algorithm in the considered parameter range proved to be more effective. The presented results broaden the existing discussion on the application of nature-inspired algorithms for solving RRAP (Reliability Redundancy Allocation Problem) problems. From this point of view, two described test scenarios can be considered as a suitable tool for validating other algorithms in RRAP problems. Not only the values of the criterion functions can be compared, but also other introduced parameters and statistical analyse of variance (ANOVA) with post-hoc RIR Tuckey test was discussed.

The accurate of model attitude angel plays an important role on the aerodynamic test results in the wind tunnel test. The original method applies the spherical coordinate system transformation to obtain attitude angel calculation. The model attitude angel is obtained by coordinate transformation and spherical surface mapping applying the nominal attitude angel (the balance attitude angel in the wind tunnel coordinate system) indicated by the mechanism. First, the coordinate transformation of this method is not only complex but also difficult to establish the transformed relationship between the space coordinate systems especially after many steps of coordinate transformation, moreover it cannot realize the iterative calculation of the interference relationship between attitude angels; Second, during the calculate process to solve the problem the arc is approximately used to replace the straight line, the angel for the tangent value, and the inverse trigonometric function is applied. Therefore, in the calculation of attitude angel, the process is complex and inaccurate, which can be solved approximately when calculating small attack angel. However, with the advancing development of modern aerodynamic unsteady research, the aircraft tends to develop high or super large attack angel and unsteady research field. According to engineering practice and vector theory, the concept of vector angel coordinate system is proposed for the first time, and the vector angel coordinate system of attitude angel is established. With the iterative correction calculation and avoiding the problem of approximate and inverse trigonometric function solution, the model attitude calculation process is carried out in detail, which validates that the calculation accuracy and accuracy of model attitude angels are improved. Based on engineering and theoretical methods, a vector angel coordinate system is established for the first time, which gives the transformation and angel definition relations between different flight attitude coordinate systems, that can accurately calculate the attitude angel of the corresponding coordinate system and determine its direction, especially in the channel coupling calculation, the calculation of the attitude angel between the coordinate systems is only related to the angel, and has nothing to do with the change order s of the coordinate system, which simplifies the calculation process.

With Direct Laser Writing (DLW) maturing in all aspects as a manufacturing technology a toolset for quality assurance must be developed. In this work we want to introduce a first of its kind test artifact. Test artifacts are standardized 3D models with specific geometric feature to evaluate the performance of writing parameters. Test artifacts are already common in other 3D additive manufacturing technologies e.g. Selective Laser Melting. The test artifact introduced in this work was developed in particular to accommodate 1) the high geometrical resolution of DLW structures and 2) the limited possibilities to examine the resulting structure. Geometric accuracy, surface adhesion as well as confocal raman spectroscopy results were considered when evaluating the design of the test artifact. We will explain the individual features and design considerations of our DLW test artifact. The difference between two slicers, Cura and 3DPoli, and the implications on measured feature sizes and the general shape is quantified. The measured geometries are used to derive a general design guide for a specific combination of photoresist, laser power and scanning speed and to analyse the geometric accuracy of a structure produced using these guidelines.

The importance of statistics in biological research is inevitable. The appliance of statistics is the most powerful tool to support the scientific hypothesis and to give credibility to biological research methodology, to interpret convoluted explanations and conclusions based on the research findings. The evidences from literatures point the persistent statistical errors, selection of non-proper statistical test with the consequence of misinterpretation of the scientific results which are published in international journals. One of the most extensively used statistical tests in the field of biology (preclinical and clinical) is analysis of variance (ANOVA). ANOVA test is in place of multiple T-tests to compare the means of more than two groups at a time; and there are some important points which biologists should be aware of them to avoid possible misinterpretation of results with the consequence of wrong conclusion. Accordingly, the aim of the current review is to help biologists to understand the basic concepts of ANOVA test and reach to a more valid interpretation of achieved results.

Despite their enormous potential the use of Indoor Localization Systems (ILS) remains seldom. One reason is the lack of market transparency and stakeholders’ trust in the systems’ performance as a consequence of insufficient use of Test and Evaluation (T&E) methodologies. The heterogeneous nature of ILS, their influences, and their applications pose various challenges for the design of a methodology that provides meaningful results. Methodologies for building-wide testing exist, but their use is mostly limited to associated indoor localization competitions. In this work, the T&E 4iLoc Framework is proposed - a methodology for T&E of indoor localization systems in semi-controlled environments based on a system-level and black-box approach. In contrast to building-wide testing, T&E in semi-controlled environments, such as test halls is characterized by lower costs, higher reproducibility, and better comparability of the results. The limitation of low transferability to real world applications is addressed by an application-driven design approach. The empirical validation of the T&E 4iLoc Framework, based on the examination of a contour-based Light Detection and Ranging ILS, an Ultra Wideband ILS, and a camera-based ILS for the application of Automated Guided Vehicles in warehouse operation, demonstrates the benefits of T&E with the T&E 4iLoc Framework.

The testing requirements of the active phased array antennas are very different from those of traditional passive antennas, due to its beam steering capability. Usually, each beam profile of the active phased array needs a separate radiation pattern test, which makes the overall testing time extremely long. Thus the traditional antenna test method can no longer meet the efficiency and cost requirements of new active phased array antennas test. In this paper, a fast test method tailored for phased array antennas is proposed that offers significantly reduced testing time at the expense of slight sacrifice of the accuracy. Using the simulated element pattern in array and ideal port excitation, the beam profile in any direction can be predicted by testing only a certain beam profile. Through theoretical derivation and experiments, the effectiveness of the method is verified, and the testing efficiency of the phased array antenna is demonstrated to be improved by ten times or even more.

The standard edge crush test (ECT) allows to determine the crushing strength of the corrugated cardboard. Unfortunately, this test cannot be used to estimate the compressive stiffness, which is an equally important parameter. It is because, any attempt to determine this parameter using current lab equipment quickly ends in a fiasco. The biggest obstacle is obtaining a reliable measurement of displacements and strains in the corrugated cardboard sample. In this paper, we present a method that not only allows to reliably identify the stiffness in the loaded direction of orthotropy in the corrugated board sample, but also the full orthotropic material stiffness matrix. The proposed method uses two samples: (a) traditional, cut crosswise to the wave direction of the corrugated core, and (b) cut at an angle of 45 degrees. Additionally, in both cases, an optical system with digital image correlation (DIC) is used to measure the displacements and strains on the outer surface of samples. The use of a non-contact measuring system allows to avoid using the measurement of displacements from the crosshead, which is burdened with a large error. Apart from the new experimental configuration, the article also proposes a simple algorithm to quickly characterize all sought stiffness parameters. The obtained results are finally compared with the results obtained in the homogenization procedure of the cross-section of the corrugated board. The results were consistent in both cases.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

Fired bricks have shown tremendous potential as a construction material due to their properties. However, their use required some specifications in terms of quality, resistance, and durability. In developing countries, the lack of tools to make test specimens leads to many defects in these brick specimens responsible for low durability and weak precision during mechanical tests and shrinkage. In this study, a simple and traditional method of making test bricks is presented. This simple method allows the production of bricks with the required properties. This method is especially efficient for a firm or semi-soft pastes consistency. The handmade pastes do not stick into the walls of the mold like the case of steel molds and it gives specimens with standard shape, smooth surface, and sharp edges. The resulting fired bricks exhibit high mechanical strength comparable and even better than those of conventional methods.

Background: The 6-minute walk test (6MWT) is a simple and low-cost method that allows assessment of functional capacity in patients with heart failure (HF). However, the prognostic role of 6MWT in HF remains uncertain. Objectives: We aimed to evaluate the 6MWT as a predictor of mid-term adverse outcomes in patients with HF with mid-range and reduced ejection fraction. Methods: Prospective single-center cohort study that included patients with HF with an ejection fraction under 50% at a specialized outpatient HF service. Patients underwent the 6MWT on admission and were compared according to the distance walked: Group I walked ≥350 meters and group II <350 meters. The primary outcome was a composite of death from any cause or hospitalization for HF decompensation in one-year follow-up. Secondary outcomes were the components of the primary outcome in an isolated analysis. Results: Sixty patients were included, 43.3% male, with a mean age of 61.1 ± 12.9 years and ejection fraction 34.3 ± 10.1%. 52 patients (86.7%) were on guideline-directed triple therapy for HF. The average distance walked in the 6MWT was 395.1 ± 98.8 meters, with 40 patients (66.7%) in group I and 20 (33.3%) in group II. The primary outcome in groups I and II were, respectively, 15,0% and 35,0% (p=0.05). One-year mortality was 5.0% vs 15.0% (p=0.18) and the hospitalization rate was 10.0% vs 20.0% (p=0.28). Conclusions: There was no association of distance <350 meters in the 6MWT with the primary outcome in patients with HF. Despite the higher occurrence of outcomes in group II, the difference was not statistically significant in this analysis. On a selective basis, the 6MWT may be a useful tool for prognostic stratification in HF, if combined with other methods.

Determining disability prevalence is an important area for population statistics, especially among young adolescents. The Washington Group on Disability Statistics is one source of reporting disabilities through functional difficulties. However, young adolescents self-reporting this measure is in its infancy. The purpose of this study was to carry out an intra-rater test-retest reliability study on a modified set of items for self-reporting functional difficulties. Young adolescents (n=74; boys=64%; age m=13.7, SD=1.8) completed a self-reported version of the child functioning module in a supervised classroom. The second administration took place two weeks later. Intraclass correlation coefficient (ICC) and Kappa (k) statistics were used to test reliability of the items, and interpretation through Landis &amp; Koch, and Cohen, respectively. The majority of items had substantial or moderate agreement, although there was only fair agreement for self-care (ICC=0.59), concentration (ICC=0.50), and routine (ICC=0.54). Kappa statistics of behaviour were interpreted to be large (k=0.65), and seeing (k=0.49), walking (k=0.49), and speaking (k=0.49) difficulties were moderate. The majority of the items in the self-reported version of the child functioning module can be used in a scale format, although some caution may be required on items of self-care and concentration when used as a dichotomous variable.

Near-Infrared Spectroscopy (NIRS) has been used to measure muscle mitochondrial capacity. The current method requires as many as 22 short ischemic occlusions to generate a recovery curve for mitochondrial capacity. PURPOSE: To determine the effectiveness of using a 6-occlusion analysis protocol to study muscle mitochondrial capacity. METHOD: Two independent, unidentified data sets were analyzed (bicep n=48, forearm n=41) from previous studies using a NIRS device (Artinis, Ltd.). Both data sets had two recovery tests that included 22 ischemic occlusions. A recovery rate used to indicate mitochondrial capacity was calculated two different ways (simultaneously). Each sample was analyzed with a MATLAB program; with a curve-fit for the 22 ischemic occlusions and curve matching for the first six ischemic cuffs and an end resting value. The two resulting rate constants were compared using correlations, both for the two data sets, good and bad fitting data, using the best 5 of 6 points for the 6 cuff approach. RESULTS: The rate constants were not significantly different between the 22 cmuff and 6 cuff for the total data sets: bicep (1.43+0.32min^-1, 1.44+0.35min^-1, p=0.56), forearm (1.94+0.42min^-1, 1.95+0.44min^-1, p=0.76). The average bicep rate constants, when compared to each other, had an equation of y=1.07x-0.09, R²=0.90. The average forearm rate constants, when compared to each other, had an equation of 0.98x+0.02, R²=0.93. CONCLUSIONS: The 6-Cuff analysis provided the same results as the longer 22-cuff. The 6-cuff approach is both shorter in time and uses less ischemic occlusion periods, increasing the practicality of the NIRS mitochondrial capacity test.

The continuing mutability of the SARS-CoV-2 virus can result in failures of diagnostic assays. To address this, we describe a generalizable bioinformatics-to-biology pipeline developed for calibration and quality assurance of inactivated SARS-COV-2 variant panels provided to Radical Acceleration of Diagnostics programs (RADx)-radical program awardees. Heuristic genetic analysis based on variant-defining mutations demonstrated the lowest genetic variance in the Nucleocapsid protein (Np)- C-terminal domain (CTD) across all SARS-COV-2 variants. We then employed the Shannon entropy method on (Np) sequences collected from the major variants, verifying the CTD with lower entropy (less prone to mutations) than other Np regions. Polyclonal and monoclonal antibodies were raised against this target CTD antigen and used to develop an Enzyme-linked immunoassay (ELISA) test for SARS-CoV-2. Blinded Viral Quality Assurance (VQA) panels comprising of UV-inactivated SARS CoV-2 variants (XBB.1.5, BF.7, BA.1, B.1.617.2, and WA1) and distractor respiratory viruses (CoV 229E, CoV OC43, RSV A2, RSV B, IAV H1N1, and IBV) were assembled by the RADx-rad Diagnostics core and tested using the ELISA described here. The assay tested positive for all variants with high sensitivity (Limit of Detection: 1.72-8.78 ng/mL) and negative for the distractor virus panel. Epitope mapping for the monoclonal antibodies identified a twenty amino acid antigenic peptide on the Np-CTD that an in-silico program also predicted for the highest antigenicity. This work provides a template for a bioinformatics pipeline to select genetic regions with a low propensity for mutation (low Shannon entropy) to develop robust ‘pan-variant’ antigen-based assays for viruses prone to high mutational rates.

This retrospective study examines 248 test-bolus examinations preceding contrast-enhanced magnetic resonance angiography (CE-MRA) to extract clinically relevant data for critical limb ischemia (CLI) management. Methods involved a retrospective review of test-bolus exams, analysing 60 graphs for time-to-peak (TTP), full-width half-maximum (FWHM) time, and time to continual rise in signal intensity. These values were correlated with heart function parameters (ejection fraction, ASA-Classification, Lee-Index, and MET-Score). Results indicate a mean TTP of 31.2 ± 7.3s, showing a correlation between ejection fraction and ASA classification. Patients with atrial fibrillation exhibited prolonged TTP compared to those without. Despite population heterogeneity, findings facilitate risk stratification for limb-saving interventions in CLI. TTP emerges as a potential clinical cardiovascular parameter and a risk factor for vascular interventions. Given the variation in injection protocols across centres, this study underscores the importance of precise bolus arrival time documentation for future multicentre studies.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

To study the anti-cracking performance of cast-in-place concrete inner shaft lining structure under the combined effects of temperature and constraint, this paper first developed a novel temperature stress test machine suitable for the shape of the inner shaft lining structure and with adjustable endpoint constraint, providing specialized experimental equipment for subsequent cast-in-place concrete inner shaft lining temperature stress simulation experiments. Then, this paper preliminarily studied the temperature, strain, and stress changes of the cast-in-place inner shaft lining under the condition of 100% endpoint constraint by simulating the internal hydration heating and cooling process of the cast-in-place inner shaft lining and using the temperature stress test machine to accurately control the endpoint constraint conditions of the inner shaft lining scaled model.