Understanding maturation stress and wood properties of poplar tension wood are critical for improving lumber yields and utilization ratio. In this study, Released Longitudinal Maturation Strains (RLMS), anatomical features, physical and mechanical properties, and nano-mechanical properties of the cell wall were analyzed at different peripheral positions and heights in nine inclined, 12-year-old poplar (Populus×euramericana ‘Zhonglin46’) trees. The correlations between RLMS and wood properties were determined. The results showed that there were mixed effects of artificial inclination on wood quality and properties. The upper sides of inclined stems had higher RLMS, proportion of G-layer, bending modulus of elasticity, and elastic modulus of cell wall but lower microfibril angle than the lower sides. At heights between 0.7 m and 2.2 m, only the double wall thickness increased with height, RLMS and other wood properties such as fiber length and basic density fluctuated or changed little with height. RLMS was a good indicator of wood properties in the tension wood area and at heights between 0.7 m and 1.5 m. The results of this study present opportunities to identify and select better quality wood in poplar trees.

Nanocellulose (CNC) seems to be a promising surfactant, which, together with expandable graphite (EG), forms the essence of an effective natural-based fire retardant wood coating. In our research, the most suitable composition of the mixture was tested concerning good solubility, dispersion, and consistency. Favorable results were achieved with the formulation composed of a 4% CNC alkaline solution with 80 wt.% of selected EG. Subsequently, six different EG were used to prepare these wood fire retardant coatings. The effectiveness of treatments was verified using a test with a radiant heat source, where the test samples' relative weight loss, relative burning rate, and surface temperature during 600 sec were evaluated. All prepared formulations can be characterized as more or less equally effective. However, the best results were obtained with EG of GG 200 – 100 N, where the mass loss of the sample was 8.10 ± 1.24%. Very good results were also achieved by graphite 25 E + 180 HPH (8.70 ± 0.89%), which is similar to the previous one, even according to the microscopic assessment of the coating as well as the expanded layer. Graphite type 25 K + 180 (8.86 ± 0.65 %) shows the expanded layer's best cohesion, coating uniformity, and ease of application. The results of this work confirmed that the CNC coating itself has significant retardation effects.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

Both soybean variety and processing affect product characteristics. This study’s objective was to characterize the effect of four extraction methods (variations of soaking and grinding) combined with cooking on the content and composition of phenolic substances, antioxidant and anti-DU145 prostate cancer cell proliferative properties of soymilk prepared from a yellow soybean of the ProSoy variety, which is a high protein variety. Results showed soymilk processing yield was the greatest by Method 4, but Method 2 gave the highest solids and protein yields by about 14 and 12%, respectively. Method 4, a two-step grinding also increased yields (8 and 7%, for solids and protein, respectively), and in all but one instance produced higher total phenolic content (TPC), total flavonoid content (TFC), condensed tannin content (CTC) and total isoflavone content in both raw and cooked soymilk as compared to Method 1. Cooking soymilk reduced 14-17% of total phenolic substances. Cooking reduced anticancer capacity of Method-4-prepared soymilk phenolic extract by increasing IC50 value from about 4.9 mg/mL to 6.8 mg/mL. The increases in phenolic compounds and antioxidants produced in Prosoy soymilk by Methods 2 and 4 with simultaneous increases in product solids yield are significant to benefit the soymilk industry and consumer health. Keywords: ProSoy yellow soybean, soymilk processing, phenolics, isoflavones, antioxidant capacity, anti-DU145 prostate cancer proliferation

High level of noise is a disturbance to the human environment. Noise in industries is also an occupational hazard because of its attendant effects on workers’ health. Noise presents health and social problems in industrial operations, and the source is related to the machineries used in the industries. One of the unique features of the noise associated with wood machinery is the level of exposure and duration. Equipment used in a factory can be extremely loud. They can produce noise at decibels high enough to cause environmental health and safety concerns. The mechanically driven transport and handling equipment, cutting, milling, shaping and dust extractor installations in the wood industry generate noise. The sources of noise pollution have increased due to non-compliance with basic safety practices. The increased use of locally fabricated machine in the industry has increased the level of noise and vibration. The effects of industrial noise pollution as discussed include: increase in blood pressure; increased stress; fatigue; vertigo; headaches; sleep disturbance; annoyance; speech problems; dysgraphia, which means reading/learning impairment; aggression; anxiety and withdrawal. As presented in this paper, noise control techniques include; sound insulation, sound absorption, vibration damping and Vibration isolation.

Enormous quantities of softwood and hardwood tree bark are generated yearly in the pulp and woodworking industry. Chemical compounds which can be found in bark extracts have important biological properties and therefore a high potential for using in the production of special formulations. In the present study, extraction of Picea abies bark with organosolv solvents was investigated to achieve a high yield of desirable compounds. For the extraction four different solvent ratios of ethanol and water were applied. The temperature range of extraction was set between 40 and 100 °C and stirring velocity of 400 rpm. Extractions were performed with a solid/liquid ratio of 1:20. Yields of phenolics, flavonoids and tannins were determined using gallic acid for total phenolic content (TPC), quercetin for total flavonoid content (TFC) and tannic acid for total tannins content (TTC) as calibration compounds. Qualitative analysis of phenolic constituents was performed after their derivatization, by gas chromatography coupled with mass spectrometry identification. The total yield of bark extract of 14.75 wt.% was achieved by using an ethanol/water ratio of 50% (v/v) and a temperature of 100 °C. Gas chromatography results show 9 aromatic carboxylic acids as phenolic acids and quercetin and (+)-catechin as flavonoid compounds. Highest concentrations of TPC = 3.21 mg gallic acid equivalent/g, TCF = 0.62 mg quercetin equivalent/g and TTC = 0.84 tannic acid equivalent/g were determined at the same process conditions by photometric method. This study determined the conditions for organosolv extraction of useful compounds and suggests that some of extractives, e.g., taxifolin and rhamnetin presented in the spruce bark extracts, have antiviral (SARS-CoV-2) effects. Therefore, this warrants further evaluation of the antiviral properties of spruce bark constituents.

The silver fir (Abies alba Mill.) is among the most valuable conifers in Europe for ecological and economic reasons. In the course of history, primarily in the 20th century, its share in stands has been declining due to ill-suited management practices, especially clear-cut management, air pollution, and wildlife-induced damage. Based on recent knowledge of fir ecology and population dynamics, small-scale shelterwood and selection management have been introduced in fir stands, which have also stabilized them. Fir is an essential species for maintaining high stability and biodiversity, especially on planosols and in waterlogged habitats. Due to its shade tolerance and environmental flexibility, particularly at higher altitudes, it can coexist very well with many tree species in mixtures, which can increase the productive potential of stands. It can form stands of heterogeneous structure, ranging from single to multi-layer to selection. For its successful natural regeneration, it is essential to reduce cloven-hoofed game and thus prevent bud browsing damage. On the other hand, fir is a species relatively resistant to bark stripping and the spread of secondary rot compared to Norway spruce (Picea abies [L.] Karst.). During global climate change, fir is expected to shift to higher elevations with sufficient precipitation, while in the southern part of its natural range or at lower elevations, outside water-influenced habitats, it is likely to decline. This paper essentially reviews the description and distribution of the species, its ecological requirements, threats and diseases, habitat and stand conditions, and close-to-nature forest management practices with emphasis on ongoing climate change.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

This article challenges the assumption that journals and peer review are essential for developing, evaluating and disseminating scientific and other academic knowledge. It suggests a more flexible ecosystem, and examines some of the possibilities this might facilitate. The market for academic outputs should be opened up by encouraging the separation of the dissemination service from the evaluation service. Publishing research in subject-specific journals encourages compartmentalising research into rigid categories. The dissemination of knowledge would be better served by an open access, web-based repository system encompassing all disciplines. There would then be a role for organisations to assess the items in this repository to help users find relevant, high-quality work. There could be a variety of such organisations which could enable reviews from peers to be supplemented with evaluation by non-peers from a variety of different perspectives: user reviews, statistical reviews, reviews from the perspective of different disciplines, and so on. This should reduce the inevitably conservative influence of relying on two or three peers, and make the evaluation system more critical, multi-dimensional and responsive to the requirements of different audience groups, changing circumstances, and new ideas. Non-peer review might make it easier to challenge dominant paradigms, and expanding the potential audience beyond a narrow group of peers might encourage the criterion of simplicity to be taken more seriously - which is essential if human knowledge is to continue to progress.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.

Recently, the concept of participatory democracy developed in the early 1970s has come back into fashion to revitalize the public involvement in political decision-making processes. Public par-ticipation in forest policy has been fully conceptualized by the scientific community in the late 1990s and early 2000s, but in many contexts the practical application remains unfulfilled. The aim of this study is to identify and analyze the participatory techniques used in literature to increase knowledge and facilitate its transferability into forest policies and strategies. A literature review was carried out to offer an overview of the participatory techniques adopted in the deci-sion-making process. At the end of literature review, 25 participatory techniques were identified based on over 2,000 publications. Afterwards, the participatory techniques were assessed using seven indicators (degree of participation, type and number of participants, time scale, cost, po-tential influence on policy). The results showed that the type of actors involved in the participa-tory technique is a key variable for the complexity and usefulness of the process, while the number of participants influences how information is disseminated. The Principal Component Analysis highlighted that the participatory techniques can be divided in three groups: the first group includes those techniques with a high degree of participation and a contextual high po-tential influence on policies, the second one includes techniques with a costs in terms of re-sources, while the third one consists of those with a large number of participants and reduced time requirements.

Autonomous weapons systems (AWS), sometimes referred to as “killer robots”, are receiving evermore attention, both in public discourse as well as by scholars and policymakers. Much of this interest is connected with emerging ethical and legal problems linked to increasing autonomy in weapons systems, but there is a general underappreciation for the ways in which existing law might impact on these new technologies. In this paper, we argue that as AWS become more sophisticated and increasingly more capable than flesh-and-blood soldiers, it will increasingly be the case that such soldiers are “in the power” of those AWS which fight against them. This implies that such soldiers ought to be considered hors de combat, and not targeted. In arguing for this point, we draw out a broader conclusion regarding hors de combat status, namely that it must be viewed contextually, with close reference to the capabilities of combatants on both sides of any discreet engagement. Given this point, and the fact that AWS may come in many shapes and sizes, and can be made for many different missions, we argue that each particular AWS will likely need its own standard for when enemy soldiers are deemed hors de combat. We conclude by examining how these nuanced views of hors de combat status might impact on meaningful human control of AWS.

Blood has certain significant physical properties, which the authors investigated. This paper provides values of surface tension and viscosity of blood at 37 °C, as well as relationship between them plotted on a cross-plot. By applying Hagen- Poiseuille equation and Jurin's law to the experimentally obtained data, the authors calculated with great accuracy viscosity and surface tension of blood. Evaluating both of the properties using described methods required from the authors to know the density of investigated liquid, which was found to be on average $\rho=1063,56 \frac{kg}{m^3}$. The authors took blood samples from 30 healthy subjects and determined aforementioned physical properties. There has been made a distinction in regard of a sex of the blood donor. Results indicate that both surface tension and viscosity are independent from sex of a subject, as well as indicate that there is no correlation between viscosity and surface tension of blood at 37\degree C. Average values of surface tension and viscosity were found to be $\sigma=5,241\pm 0,262 \cdot 10^{-2}\frac{J}{m^2}$ and $\eta=3,352\pm0,360 \cdot 10^{-3} Pa \cdot s$, respectively.

Finishing coatings in the wood-based composites industry not only influence the final appearance of the product but also serve to protect against fungi, and molds, and reduce the release of harmful substances, particularly formaldehyde and volatile organic compounds (VOCs). Carbon-rich materials, such as those derived from birch bark extraction, specifically suberin acids, can fulfil this role. Previous research has demonstrated that adding suberin acid residues (SAR) at 20% and 50% by weight significantly enhances the gas barrier properties of surface finishing materials based on poly(lactide) (PLA) and polycaprolactone (PCL), particularly in terms of Total VOC (TVOC) and formaldehyde emissions. This study aims to explore whether these properties can be further improved through the incorporation of nano-zinc oxide (nano-ZnO). Previous research has shown that these nanoparticles possess strong resistance to biological factors and can positively affect the characteristics of nanofilms applied as surface protection. The study employed PLA and PCL finishing layers blended with SAR powder at 10% w/w and included 2% and 4% nano-zinc oxide nanoparticles. The resulting blends were milled to create a powder, which was subsequently pressed into 1 mm thick films. These films were then applied to raw particleboard surfaces. TVOC and formaldehyde emission tests were conducted. Additionally, the fungal resistance of the coated surfaces was assessed. The results showed that PLA/SAR and PCL/SAR composites with the addition of nano-zinc oxide nanoparticles exhibited significantly improved barrier properties, offering a promising avenue for developing biodegradable, formaldehyde-free coatings in the furniture industry with enhanced features. Furthermore, by utilizing SAR as a post-extraction residue, this project aligns perfectly with the concept of upcycling.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Sterile alpha motif domain-containing protein 9 (SAMD9) is a regulatory protein centrally involved in cell proliferation and apoptosis. Mapped to 7p21.1, variants in SAMD9 have been reported in <50 pediatric cases worldwide, typically with early lethality. Germline gain-of-function SAMD9 variants are associated with MIRAGE Syndrome (myelodysplasia, infection, restricted growth, adrenal hypoplasia, genital anomalies, and enteropathy). Spalt like transcription factor 1 (SALL1) is a zinc finger transcriptional repressor located at 16q12.1 where only two transcript variants in SALL1 are known. RUNX2 (6p21.1) encodes a nuclear protein with a Runt DNA-binding domain critical for osteoblastic differentiation, skeletal morphogenesis, and serves as a scaffold for nucleic acids and regulatory factors involved in skeletal gene expression. RUNX2 and SALL1 are thus both ‘master regulators’ of tissue organization and embryo development. Here, we describe exome sequencing and copy number variants in two previously unknown mutations—R824Q in SAMD9, and Q253H in SALL1. A new multiexon 3’ terminal duplication in RUNX2 is also reported. This is the first known phenotype characterization for the intersection of all three variants in a healthy 46,XX adult. Focusing on developmental progress, ultrastructural renal anatomy, and selected reproductive aspects, we describe this unique genotype diagnosed incidentally during Covid-19 illness. Individual disruption in SAMD9, RUNX2, or SALL1 would be expected to give a bleak prognosis. However, the convergence discovered here appears to dampen severe pathology, perhaps by cross-gene silencing of effects normally deleterious when such changes occur alone.

The first published description of intraovarian platelet-rich plasma (PRP) appeared in mid-2016, when a new experimental technique was successfully used in adult human ovaries to correct the reduced fertility potential accompanying advanced maternal age. Considering the potential therapeutic scope of intraovarian activated PRP and/or condensed platelet cytokines would likely cover both menopause treatment and infertility, the mainstream response has ranged from skeptical disbelief to welcome astonishment. Indeed, reports of restored menses in menopause (as an alternative to conventional hormone replacement therapy) and healthy term livebirths for infertility patients (either with IVF or as unassisted conceptions) after intraovarian PRP injection continue to draw notice. Yet any proper criticism of ovarian PRP applications will be difficult to rebut given the heterogenous patient screening, varied sample preparations, wide differences in platelet incubation and activation protocols, surgical/anesthesia techniques, and delivery methods. Notwithstanding these features, no adverse events have been reported thus far and ovarian PRP appears well tolerated by patients. Here, early research guiding the transition of ‘ovarian rejuvenation’ from experimental to clinical is outlined. Likely mechanisms are presented to explain results observed in both veterinary and human ovarian PRP research. Current and future challenges for intraovarian cytokine treatment are also discussed.

Involving local people in natural area management is very important to address the complexity of environmental management issues for sustainable use of local resources. Participatory methods require the contribution of local stakeholders in decision making. Mapping the environmental views of local communities allows for detecting aspects that could facilitate management efforts. This research – in the frame of the Skyros LIFE project and the PAMNATURA project - measures local acceptability of the conservation actions proposed by the LIFE project in Skyros Island (Greece) in relation with recording local people’s environmental orientation using the 15-item revised New Ecological Paradigm (NEP) scale. The research was carried out by means of questionnaires. The LIFE project proposed actions were grouped into three categories according to their theme, i.e. promoting (a) Nature protection, (b) Agro-pastoralism and (c) Ecotourism. The sample seems to largely agree with the LIFE project proposals, while the results showed high scores for most of the NEP scale items, implying pro-environmental beliefs, though there appears disagreement or neutrality regarding a few items. Local acceptability of the proposed actions was found to correlate to local people’s environmental concern measured through the NEP scale. Drawing on the results, implementation of actions related directly or indirectly to economic activities, preservation of traditional activities, as well as environmental education, interactive informing and consultation could enhance local participation. Skyros island seems to offer an appropriate social background for applying participatory and adaptive management and implementing conservation programs.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

The notion of the three-phase (line) tension remains one of the most disputable notions in the surface science. A very broad range of its values has been reported. Experts even do not agree on the sign of the line tension. The polymer-chain-like model of the three-phase (triple) line enables the rough estimation of the entropic input into the value of the line tension, estimated as Γ_en≅(k_B T)/d_m ≅〖10〗^(-11) N, where d_m is the diameter of the liquid molecule. The introducing of the polymer-chain-like model of the triple line is justified by the “water string” model of the liquid state, predicting strong orientation effects for liquid molecules located in the vicinity of hydrophobic moieties. The estimated value of the entropic input into the line tension is close to experimental findings, reported by various groups.

Covid-19 has caused infections and deaths worldwide. While research in the field of Data Science has contributed good predictions of positive Covid-19 case numbers, this study's review of literature shows there is little research in the use of variants of the virus in predictions. We set out to define and evaluate novel variant features. We find that features relating to variant trends, thresholds and amino acid substitutions are especially powerful in two tasks. In the first task, predicting Covid-19 case numbers, accuracy improved from 71.53% without variant features to 82.12% with variant features. In the second task, predicting transmission severity of variants between two classes, we created a method to build some variable ensembles through selecting appropriate models that are generated with variant features. The test results showed that our ensembles are more accurate and reliable. One particular ensemble of 14 models correctly classified 90.91% of variants, outperforming other models including the popular Random Forest ensemble. In addition, as the variant features have represented more underlying information about Covid-19 pathophysiology, our ensemble methods use only a few data samples to achieve an accurate prediction. The ensemble of 14 models uses only 50 cases of each variant, an ability that could be exploited for early detection of highly infectious variants. These research findings may benefit public health professionals, policy makers, and the research community in the collective efforts to overcome this disease.

Powder Bed Fusion (PBF) is a type of Additive Manufacturing (AM) technology that builds parts in a layer-by-layer fashion out of a bed of metal powder via the selective melting action of a laser or electron beam heat source. The technology has become widespread, however the demand is growing for closed loop process monitoring and control in PBF systems to replace the open loop architectures that exist today. This paper demonstrates the simulated efficacy of applying closed-loop state estimation to the problem of monitoring temperature fields within parts during the PBF build process. A simplified LTI model of PBF thermal physics with the properties of stability, controllability and observability is presented. An Ensemble Kalman Filter is applied to the model. The accuracy of this filters’ predictions are assessed in simulation studies of the temperature evolution of various test parts when subjected to simulated laser heat input. The significant result of this study is that the filter supplied predictions that were about 2.5x more accurate than the open loop model in these simulation studies.

Fusarium species are agriculturally important fungi with a broad host range and can be found as endophytic, pathogenic, or opportunistic parasites in many crop plants. This study aimed to identify Fusarium species in bare-rooted, dormant plants in Turkish grapevine nurseries using molecular identification methods and assess their pathogenicity. Asymptomatic dormant plants were sampled from grapevine nurseries (43) in different regions of the country, and fungi were isolated from plant roots and internal basal tissues. The Fusarium isolates were identified by performing gene sequencing (TEF1-α, RPB2) and phylogenetic analyses. Pathogenicity tests were carried out by inoculating mycelial agar pieces of isolates onto the stem or conidial suspensions into the rhizosphere of vines (1103 Paulsen rootstock). Laboratory tests revealed that Fusarium species were highly prevalent in Turkish grapevine nurseries (41 out of 43). Gene sequencing and phylogenetic analyses unraveled that 12 Fusarium species (F. annulatum, F. brachygibbosum, F. clavum, F. curvatum, F. falciforme, F. fredkrugeri, F. glycines, F. nanum, F. nematophilum, F. nirenbergiae, F. solani, and Fusarium spp.) existed in the ready-to-sale plants. Some of these species (F. annulatum, F. curvatum and F. nirenbergiae) consistently caused wood necrosis of seedling stems, rotting of the basal zone and roots, and reduced root biomass. Although the other nine species also caused some root rot and root reduction, their virulence was not as severe as the pathogenic ones, and they were considered opportunistic parasites or endophytic species. This study is the first detailed investigation of Fusarium species in grapevine nurseries in Türkiye and emphasizes the need to consider pathogenic species in producing healthy grapevine seedlings.

We consider the role information energy can play as a source of dark energy. Firstly, we note that, if stars and structure had not formed in the universe, elemental bits of information describing the attributes of particles would have exhibited properties similar to the cosmological constant. The Landauer equivalent energy of such elemental bits would be defined identical in form and value to the characteristic energy of the cosmological constant. But, with the formation of stars and structure, stellar heated gas and dust now provides the dominant contribution to information energy with the characteristics of a dynamic, transitional, dark energy. At low redshift, z<~1.35, this dark energy emulates the cosmological constant with a near constant energy density, w=−1.03±0.05, and an energy total similar to the mc² of the universe's ∼10⁵³ kg of baryons. At earlier times, z>~1.35, information energy was phantom, differing from the cosmological constant, Λ, by a CPL parameter difference of ∆w_o=−0.03±0.05 and ∆w_a=−0.79±0.08, values sufficient to account for the H₀ Tension. Information dark energy agrees with most phenomena as well as Λ, while exhibiting characteristics that resolve many tensions and problems of ΛCDM: the cosmological constant problem; the cosmological coincidence problem; the H₀ and σ₈ tensions. As this proposed dark energy source is not usually considered, we identify the expected signature in H(a) that will enable the role of information dark energy to be falsified by experimental observation.

CO2 emission activity of xylotrophic fungi response to an increase in temperature in the range of 10-30 °C on the example of pure dikaryotic cultures of Fomes fomentarius s. str., F. inzengae, Fomitopsis betulina, F. pinicola, Phellinus igniarius was analyzed. Emission activity was assessed by the difference in CO2 concentration in 0.5-liter exposure chambers with Petri dishes with mycelium growing on agar at the beginning of exposure and an hour later using a Gasmet DX-4030 FTIR spectrometer (Gasmet Technologies Oy, Finland), error measurements ±50 ppm. Specific (μg CO2/cm2/h) and total (μg CO2/h) emission activity and its relationship with temperature and size (area) of the mycelium were assessed. It has been shown that in the range of 10-30 °C, the specific and total CO2 emission activity of the mycelium is closely and positively related to temperature. Specific emission, which is an indicator of the respiratory activity of the mycelium, does not depend on its size; its only driver is temperature, the relationship with which is linear: an increase in temperature by 10 °C causes an increase in the specific emission activity of the mycelium by 1.7 times. The total CO2 emission activity, which is an indicator of the total amount of CO2 emitted, is directly proportional to the specific emission activity and the size of the mycelium. In the range of 10-30 °C, an increase in temperature causes an almost equal increase in both the specific emission activity of the mycelium (Q10 1.7) and its growth (Q10 1.5) and causes an exponential increase in the total emission of CO2. This must be taken into account when predicting CO2 emissions from woody debris under climate change, as it could potentially contribute to accelerating climate change.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

We introduce two symmetric concepts to physics: “distance” (space and time in one) and “wavematter” (electromagnetic wave packet and matter in one). We claim that physics has chosen the wrong concept of time: It is not aware that the time of a moving object flows in a direction other than my time. We provide 15 proofs for our claim by solving 15 mysteries of physics graphically! For example, we prove that length contraction and time dilation are actually geometrical effects in a 4D manifold that we call “Euclidean spacetime” (ES). We prove that the discrepancy in calculating the Hubble constant stems from a systematic error in the redshift measurement. We prove that what I deem wave, deems itself matter, which solves wave–particle duality. We even untangle quantum entanglement without the issue of non-locality. We finally understand why alternative theories of Euclidean relativity have failed: They are all based on four dimensions of space rather than distance. A huge amount of energy was injected into ES at a point that we take as origin. Ever since has this energy been moving radially away at the speed of light. We live in the 3D hypersurface of an expanding 4D hypersphere. Hyperspherical coordinates have the great advantage that they reduce all that is ever happening to just one formula. So, it is the Theory of Everything in these coordinates: “Energy is covering radial distance which, divided by Euclidean time, is equal to the speed of light.” Acceleration and force like gravitation emerge from a rotation of objects in ES and a subsequent projection to 3D space. Matching the symmetry simplifies physics.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

Shape Memory Polymer (SMP) actuators are smart materials that adapt and switch shape in response to environmental conditions, allowing controlled and dynamic building systems. The integrated SMP strip enabled the adaptive facade shading system to operate independently and with flexibility under certain thermoresponsive conditions to regulate building performance. This study aims to improve adaptive façade performance in a hot-humid climate by determining optimal thermal activation factors for the shape memory polymer. This was achieved by comprehensively examining and analysing the impact of various SMP activation parameters on energy efficiency, thermal comfort, and visual comfort. In addition, dynamic IES-VE building energy simulation was used to evaluate the thermal performance of the adaptable facade. The results were validated using a multicriteria approach to compare with the existing glass façade of a high-rise apartment. The results showed that the coactivation technique, which combines solar radiation and air temperature triggers, proved to be the most efficient strategy to improve the performance of the adaptive façade. This strategy minimised heat gain, lowered indoor temperatures, reduced glare, and enhanced daylight comfort, resulting in notable energy savings through reduced cooling consumption. The study concluded that the utilisation of SMP actuators with fine-tuning activation parameters significantly optimised adaptive façade performance, promoting functionality, efficiency, and sustainability in buildings.

Japanese plum tree (Prunus salicina Lindl.) is mainly cultivated in temperate areas of China and some European countries. Certain amounts of wood (from pruning works) are generated every year from this crop of worldwide commercial significance. The main objective of this work was to value this agricultural woody residue, for which the chemical composition of pruning wood extracts from six Japanese plum cultivars was investigated, and the antiproliferative activity of extracts and pure phenolics present in those extracts was measured. For the chemical characterization, total phenolic content and DPPH radical-scavenging assays and HPLC‒DAD/ESI‒MS analyses were performed, the procyanidin (‒)-ent-epicatechin-(2α→O→7,4α→8)-epicatechin (5) and the propelargonidin (+)-epiafzelechin-(2β→O→7,4β→8)-epicatechin (7) being the major components of the wood extracts. Some quantitative differences were found among plum cultivars, and the content of proanthocyanidins ranged from 1.50 (cv. ‘Fortune’) to 4.44 (cv. ‘Showtime’) mg/g of dry wood. Regarding the antitumoral activiy, eight wood extracts and four phenolic compounds were evaluated in MCF-7 cells after 48 h of induction, showing the wood extract from cv. ‘Songold’ and (‒)-annphenone (3) the best antiproliferative activity (IC50: 424 ppm and 405 ppm, respectively).

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

This brief review highlights some current issues in Galactic stellar nucleosynthesis, and some recent laboratory studies by the Wisconsin atomic physics group that have direct application to stellar spectroscopy, in order to advance our understanding of the chemical evolution of our Galaxy. The relevant publication history of the lab studies are summarized, and investigations into the abundances of neutron-capture and iron-peak elements in low metallicity stars are described. Finally, new initatives in near-infrared spectroscopy are briefly explored.

A recently developed thermodynamic theory for the determination of the driving force of crystallization and the crystal–melt surface tension is applied to the ice–water system employing the new Thermodynamic Equation of Seawater TEOS-10. The deviations of approximative formulations of the driving force and the surface tension from the exact reference properties are quantified, showing that the proposed simplifications are applicable for low to moderate undercooling and pressure differences to the respective equilibrium state of water. The TEOS-10 based predictions of the ice crystallization rate revealed pressure-induced deceleration of ice nucleation with an increasing pressure, and acceleration of ice nucleation by pressure decrease. This result is in, at least, qualitative agreement with laboratory experiments and computer simulations. Both the temperature and pressure dependencies of the ice–water surface tension were found to be in line with the le Chatelier–Braun principle, in that the surface tension decreases upon increasing degree of metastability of water (by decreasing temperature and pressure), which favors nucleation to move the system back to a stable state. The reason for this behavior is discussed. Finally, the Kauzmann temperature of the ice–water system was found to amount TK=116K, which is far below the temperature of homogeneous freezing. The Kauzmann pressure was found to amount pK=-212MPa, suggesting favor of homogeneous freezing upon exerting a negative pressure on the liquid. In terms of thermodynamic properties entering the theory, the reason for the negative Kauzmann pressure is the higher mass density of water in comparison to ice at the melting point.

We demonstrate how a rigorous mathematical approach can be used to extract a current CMB temperature of 2.7276 ±0.0723 K from the 580 type Ia supernova data points in the Union2 database. Using redshift formula: z = Sqrt(Rh/R_t) − 1, incorporated into our new CMB redshift prediction redshift formula, we find that the above current CMB temperature value is a remarkably good match for this particular data set. In addition, we can alternatively start out with the measured current CMB temperature and extract the Hubble constant from all 580 supernovae. We then get an estimated Hubble constant of H0 = 66.8711+0.0019 km/s/Mpc when using the CMB temperature from the recent Dhal et al study [1] in combination with redshifts from all 580 supernovae. Furthermore, we get an estimated Hubble constant value of H_0 = 66.8943+0.0287 km/s/Mpc when using the CMB temperature measured by Fixsen [2]. In summary, our simple model essentially perfectly matches all 580 type Ia supernova redshifts while extracting H_0 or T_0 values. The Hubble constant we extract by this method fits very well with the Hubble constant extracted from the CMB by other studies. We believe that our new approach likely solves the Hubble tension problem, at least inside R_h = ct cosmology.

Two anisotropic exact Bianchi type I solutions of Einstein’s field equations that generalize the isotropic ΛCDM universe model, are used to investigate the Hubble tension. It is shown that the cosmic anisotropy as deduced from the Planck measurements of the fluctuations in the temperature of the cosmic microwave background radiation, is ten billion times too small to solve the Hubble tension.

Our comprehension of fundamental cosmological principles hinges on a thorough understanding of the early universe. The Lambda Cold Dark Matter (ΛCDM) model has emerged as a valuable framework for elucidating various cosmic phenomena, uniting a cosmological constant (Λ) with cold dark matter (CDM). Nevertheless, recent observations, particularly data from the Planck, WMAP, and DES missions that probe the early universe, alongside local measurements of the Hubble constant, have unveiled significant inconsistencies. These inconsistencies have magnified the perplexing issue known as the Hubble Tension, thereby challenging our current understanding of the universe. To address this conundrum, we adopt a comprehensive approach encompassing a review of cosmological fundamentals, an exploration of the ΛCDM model, an examination of the cosmic microwave background (CMB), power spectrum, and perturbation theory, a thorough review of existing research, and finally, an investigation of real data. By undertaking these early universe processes, we aim to understand more about Hubble constant and its consequence in ΛCDM model.

A novel method of investigating the temperature dependent variation of aspects of the complex refractive index n* in samples in the THz range using continuous, non-polarised, synchrotron radiation is presented. The method relies on the use of ATR apparatus, and retains the advantage of minimal sample preparation, which is a feature of ATR techniques. The method demonstrates the viability of rapidly monitoring temperature reflectance whilst continuously heating or cooling samples by using a temperature variable Thermal Sample Stage. The method remains useful when the refractive index of the sample precludes attenuated total reflection study. This is demonstrated with the water reflectance experiments. The temperature dependent ATR reflectance of tissue-representative fats (lard and Lurpak® butter) was investigated with the novel approach. Both are within the ATR range of the diamond crystal in a “true” ATR mode. Lard showed no clear temperature variation between -15 0C and 24 0C at 0.7 to 1.15 THz or 1.70 to 2.25 THz. Lard can be regarded as having invariable, constant, dielectric properties within mixtures when biological substances are being assessed for temperature dependent dielectric variation within the stated THz ranges. Lurpak® butter (water content 14.7%) displayed temperature dependent reflectance features with a steady decline in reflectivity with increasing temperature. This is in line with the temperature-dependent behaviour of liquid water. There is no rapid change in reflectance, even at -20 0C, suggesting that emulsified water retains liquid-water-like THz properties at freezing temperatures.

Polyamide 11 (PA11) is a plant-based nylon made from castor beans. Powder bed fusion laser sintering (PBF-LS) is an additive manufacturing process used for PA11 which allows the reuse of the unsintered powder. The unsintered powder is mixed with virgin powders at different refresh rates which has been studied extensively for most semi-crystalline polyamides. However, there is lack of information on the effect of using 100% reused PA11 powder and the number of times it is reused on its own during powder bed fusion laser sintering. This paper investigates the effect of reusing PA11 powder in PBF-LS and number of times it is reused on the dimensional accuracy, density, thermal and tensile properties. From 100% virgin powder to 3rd use of the powder, there is a decrease in powder wastage, decrease in crystallinity and tensile strength. These was associated with the polymerisation and cross-linking process of polymer chains, upon exposure to high temperature. This results in a higher molecular weight and hence density. From the 4th use to 10th reuse, the opposite was observed which was associated to an increase in high-viscosity and un-molten particles which resulted in defects in the PBF-LS parts.

The continuous and precise mapping of glacier calving fronts is essential for monitoring and understanding rapid glacier changes in Antarctica and Greenland, which have the potential for significant sea level rise within the current century. This effort has been mostly restricted to the slow and painstaking manual digitalization of the calving front positions in thousands of satellite imagery products. Here, we have developed a machine learning toolkit to robustly and automatically detect glacier calving front margins in satellite imagery. The toolkit is based on semantic image segmentation using Convolutional Neural Networks (CNN) with a modified U-Net architecture to isolate the calving fronts from satellite images after having been trained with a dataset of images and their corresponding manually-determined calving fronts. As a case study we train our neural network on a varied set Landsat images with lowered resolutions from Jakobshavn, Sverdrup, and Kangerlussuaq glaciers, Greenland and test the results on novel images from Helheim glacier, Greenland to evaluate the performance of the approach. The neural network is able to identify the calving front in new images with a mean deviation of 96.3 m from the true fronts, equivalent to 1.97 pixels on average, while the corresponding error for manually-determined fronts on the same resolution images is 92.5 m. We find that the trained neural network significantly outperforms common edge detection techniques, and can be used to continuously map out calving-ice fronts with a variety of data products.

According to this study, approximately half of Africa's forests are utilized primarily or partially for the production of wood and non-wood commodities. Aims to evaluate Africa's forestry and forest products, namely Wood Forest Products (WFPs) and Non-wood Forest Products (NWFPs) in the sixteen (16) West African countries. While adhering to the following guidelines: wood extraction and preparation, analyzing wood primarily used as an energy source in Africa, identifying non-wood forest products in Africa, the state of export, trade, and customs procedures in West Africa, and examining the role of forests and forest stakeholders in Africa's low-carbon economy transition. An exploratory literature review of selected wood forest products and non-wood forest products (plants and animals) in West Africa identifying the country, the natural land area with the natural habitat issues of the forest, the species most harvested and traded in the West African sub-region. The study reemphasized some government legislation, policies, and market trade failures and limitations while also stating that trees may help in the low-carbon revolution through interventions aimed at maintaining, improving, and restoring natural capital have demonstrated that high environmental requirements of sustainable forest management (SFM) may be met in both natural and planted forests. The study identified a systematic assessment of the most common forest products (wood and non-wood forest products) considering the available data on the national forest reserves of the selected countries in West Africa. The study also revealed the need for biodiversity conservation of the available forest reserves to help mitigate the impact of global warming targeting the United Nation’s Sustainable Development Goal 13- Climate Action. Which is focused on integrating climate change mitigation, adaptation, impact reduction, and early warning signs into the national policies, improving forest planning and management education, awareness-raising, and institutional capacity within the sub-region.

The ultimate analysis parameters including carbon (C), hydrogen (H), nitrogen (N), and oxygen (O) content in biomass was rarely found to be predicted by nondestructive tests until to date. In this research, we developed partial least squares regression (PLSR) models to predict the ultimate analysis parameters of chip biomass using near infrared (NIR) raw spectra of non-wood and wood samples from fast growing tree and agricultural residue and nine different traditional spectral preprocessing techniques. These techniques include first derivative (sd1), second derivative (sd2), constant offset, standard normal variate (SNV), multiplicative scatter correction (MSC), vector normalization, min-max normalization, mean centering, sd1 + vector normalization, and sd1 + MSC. Additionally, we employed a genetic algorithm (GA), successive projection algorithm (SPA), multi-preprocessing (MP) 5−range, and MP 3−range to develop a PLSR model for rapid prediction. A dataset consisting of 120 chip biomass samples was utilized for model development in which the samples was non-wood samples of 65-67% and wood samples was 33-35%, and the model performance were evaluated and compared. The selection of the optimum performing model was mainly based on criteria such as the coefficient of determination in the prediction set (R2P), root mean square error of the prediction set (RMSEP), and the ratio of prediction to deviation values (RPD). The optimal model for weight percentage (wt.%) of C was obtained using GA−PLSR, yielding R2P, RMSEP, and RPD values of 0.6954, 1.1252 wt.%, and 1.8, respectively. Similarly, for wt.% of O, the most effective model was obtained using the multi-preprocessing PLSR−5 range method with R2P of 0.7150, RMSEP of 1.3088 wt.%, and RPD of 1.9. For wt.% of N, the optimal model was obtained using the MP PLSR−3 range method, resulting in R2P, RMSEP, and RPD values of 0.6073, 0.1008 wt.%, and 1.6, respectively. However, wt.% of H model provided R2P, RMSEP, and RPD values of 0.5162, 0.2322 wt.%, and 1.5, respectively. Notably, the limit of quantification (LOQ) values for C, H, and O were lower than the minimum reference values used during model development, indicating a high level of sensitivity. However, the LOQ for N, exceeded the minimum reference value, implying the samples to be predicted by the model must be in the range of reference range in calibration set. By scatter plot analysis, the effect of combined non-wood and wood spectra of biomass chips on rapid prediction of ultimate analysis parameters using NIR spectroscopy was investigated. To include different species in a model, the species have to be not only in the different values of the constituents to make a wider range for robust model but also they must provide their trend line characteristics in the scatter plot i.e. correlation coefficient (R), slope and intercept (same slope and slope approached to 1 and intercept is same (no gap) and approached zero, high R approached to 1). The effect of the R, slope and intercept to obtain the better optimized model were studied. The results show that the different species affected model performance of each parameter prediction in a different manner and by scatter plot analysis which of these species were affecting the model negatively and how the model could be improved was indicated. This is the first time of the effect is studied by the principle of scatter plot.

Laser powder bed fusion (LPBF) is an additive manufacturing technique that is gaining popularity for producing metallic parts in various industries. However, parts produced by LPBF are prone to residual stress, deformation, cracks and other quality defects due to uneven temperature distribution during the LPBF process. To address this issue, in prior work, the authors have proposed SmartScan, a method for determining laser scan sequence in LPBF using an intelligent (i.e., model-based and optimization-driven) approach, rather than using heuristics, and applied it to simple 2D geometries. This paper presents a generalized SmartScan methodology that is applicable to arbitrary 3D geometries. This is achieved by: (1) expanding the thermal model and optimization approach used in SmartScan to multiple layers; (2) enabling SmartScan to process shapes with arbitrary contours and infill patterns within each layer; (3) providing the optimization in SmartScan with a balance of exploration and exploitation to make it less myopic; and (4) improving SmartScan's computational efficiency via model order reduction using singular value decomposition. Sample 3D test artifacts are simulated and printed using SmartScan in comparison with common heuristic scan sequences. Reductions of up to 92% in temperature inhomogeneity, 86% in residual stress, 24% in maximum deformation and 50% in geometric inaccuracy were observed using SmartScan, without significantly sacrificing print speed. An approach for using SmartScan for printing complex 3D parts in practice, by integrating it as a plug-in to a commercial slicing software, was also demonstrated experimentally, along with its benefits in significantly improving printed part quality.

Castanopsis hystrix, a precious tree species in Southeast Asia, has the advantages of rapid growth and high-quality wood materials. However, there are problems such as long breeding cycle, time-consuming and low efficiency, which greatly restricts the industrial development of C. hystrix. To perform the genome selection (GS) for growth and wood traits and the early selection of superior progeny have great significance for the rapid breeding of new superior varieties of C. hystrix. The 226 clones in the main distribution and 479 progenies within 23 half-sib families were used as experimental materials in this study. Genotyping datasets were obtained by high-throughput re-sequencing technology, and GS studies were conducted on the growth (tree height (H), diameter at breast height (DBH)) and wood (wood density (WD), fiber length (FL), and fiber length-width ratio (LWR)) traits. The coefficient of variation (CV) of five phenotypic traits ranged from 10.1% to 22.73%, the average CV of growth traits was 19.93%, and the average CV of wood traits was 9.72%. The Pearson correlation coefficients between the five traits were almost significantly positive. Based on the Genomic Best Linear Unbiased Prediction (GBLUP) model, the broad-sense heritabilities of growth traits were higher than those of wood quality traits, and the different number of SNPs had little effect on the heritability estimation. GS prediction accuracy first increased and then reached a plateau around 3K SNPs for all five traits. The broad-sense heritability of these five traits was significantly positively correlated with their GS predictive ability (r=0.564, P

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

The purpose of this work is to analyze heat-treated ash wood at temperature of 185 ºC, in order to analyze its dimensional stability. For comparison, native ash/ not thermally treated wood, was be used. In order to analyze heat-treated ash wood, some main properties such as water absorption, swelling in thickness, roughness, Brinell hardness, modulus of rupture and elasticity, color change toward black with CIELab space, and many others properties were determined and processed. The results obtained after processing the experimental data have showed that heat-treated ash wood had good physical properties as absorption and swelling in thickness, and the slight increase in elasticity offers new fields of use. As a general conclusion of the work, it was established that the ash wood can be properly thermally treated, the dimensional stability characteristics being very good, and the decrease in bending resistance being almost imperceptible.

To investigate this suitability of Black Mustard (Brassica Nigra L.) and Camelina (Camelina Sativa L.) for pulp manufacturing the nitrate-alkaline method was used. The non-wood plants were characterized by chemical analysis, especially lignin, cellulose, ash, extractives and alpha-, beta-, gamma-cellulose. The pulp was cooked in 6% nitric acid and then underwent the extraction by 5% sodium-hydroxide and neutralized by 1% acetic acid. The cooked pulp was characterized by delignification degree – Kappa number. The laboratory sheets were made from this cooked pulp and they were characterized by tensile index, breaking length, smoothness and compared with commonly available papers.

No major breakthroughs have entered mainstream clinical fertility practice since egg donation and intracytoplasmic sperm injection decades ago, and oocyte deficits secondary to advanced age continue as the main manifestation of diminished ovarian reserve. In the meantime, several unproven IVF ‘accessories’ have emerged including so-called ovarian rejuvenation which entails placing fresh autologous platelet-rich plasma (PRP) directly into ovarian tissue. Among cellular responses attributed to this intervention are reduced oxidative stress, slowed apoptosis, and improved metabolism. Besides impacting the existing follicle pool, platelet growth factors might also facilitate de novo oocyte recruitment by specified gene upregulation targeting uncommitted ovarian stem cells. Because disordered activity at mechanistic target of rapamycin (mTOR) has been shown to exacerbate or accelerate ovarian aging, PRP-discharged plasma cytokines combined with mTOR suppression by pulsed/cyclic rapamycin represents a novel fusion technique to enhance ovarian function. While beneficial effects have already been observed experimentally in oocytes and embryos with mTOR inhibition alone, this is the first discussion of intraovarian platelet cytokines followed by low-dose, phased rapamycin. For refractory cases, this investigational, tailored approach could amplify or sustain ovarian capacity sufficient to permit retrieval of competent oocytes via distinct but complementary pathways—thus reducing dependency on oocyte donation.

The objective of this study is to preliminarily evaluate a new CT-biopsy guidance device, an origami needle guide. The device is created by laser cutting the structure from a sheet of cardboard, 3D printing two radiocontrast agent grids on to the surface and folding the structure into a rectangular prism with a viewing window. An abdominal imaging phantom was used to evaluate the device through CT imaging and the targeting of lesions for needle insertion. The lesion targeting trials resulted in a mean targeting error of 1.88 mm with a standard deviation of 0.73 mm. The device attaches to the patient and is rigid enough to adequately support standard biopsy needles, reducing the effect of gravity and the risk of laceration by the needles, making it potentially advantageous for biopsy of superficial lesions and lesions approached from a horizontal orientation. The device supports insertion of multiple needles at once, making it particularly suitable for composite ablation using multiple needles. Another advantage of the device is that it can guide off-axial needle insertion. The low-cost and disposability of the device make it well-suited for the minimally invasive image guided therapy environment.

This study examines the impact of chainsaw chain type and tree species on the concen-tration of inhalable wood dust generated during motor-manual harvesting in forested areas. The chainsaw chain is a critical component, contributing not only to productivity but also to the oper-ator's health and safety. Wood dust creation during harvesting operations poses significant risks and necessitates careful attention due to its potential health effects. We investigated the effects by conducting real-world measurements of inhalable dust within the operator's breathing zone during forestry work. Two different chain types were evaluated: the commonly used 3/8" pitch chain (conventional chain) and the 0.325" pitch chain. Additionally, measurements were taken for three tree species: beech, oak, and pine (including both live and standing dead trees after a fire). Results showed that, overall, using the conventional 3/8" chain type yielded the highest concentration of wood dust for all three tree species. Notably, the highest wood dust concentration was observed in the burned Pinus brutia cluster, also with the 3/8" chain pitch. These findings emphasize the im-portance of understanding how chain type and tree species contribute to wood dust levels and provide valuable insights for enhancing operator health and safety during motor-manual har-vesting operations

We report the case of a 44-year-old woman who suffered gastric perforation after receiving bag-valve-mask (BVM) ventilation in the setting of alcohol intoxication. She had a markedly distended abdomen and cold, dusky lower extremities upon arrival to the emergency department. Imaging revealed a large volume intraabdominal accumulation of air with compression of the aorta. Needle decompression relieved symptoms of lower extremity arterial insufficiency. However, the patient quickly decompensated and subsequent exploratory laparotomy confirmed gastric rupture. A subtotal gastrectomy was performed but the patient ultimately passed on post-operative day two due to multi-organ dysfunction. Although BVM ventilation is commonplace in both the hospital and field, there is a lack of awareness of the serious complications of abdominal air accumulation due to their rareness in the adult population. Checking for abdominal distention during resuscitation ought to be routine in all patients. Signs of arterial insufficiency accompanying abdominal distention, once confirmed by diagnostic imaging that shows extensive pneumoperitoneum, are indicators of having reached a life-threatening level of air accumulation, calling for immediate needle decompression and exploratory laparotomy.

Pure-compression shells have been the central topic in the form-finding of shells. This paper studies tension-compression mixed type shells by utilizing a NURBS-based isogeometric form-finding approach that analyzes Airy stress functions to expand the possible plan geometry. A complete set of smooth version graphic statics tools is provided to support the analyses. The method is validated using examples with known solutions, and a further example demonstrates the possible forms of shells that the proposed method permits. Additionally, a guideline to configure a proper set of boundary conditions is presented through the lens of asymptotic lines of the stress functions.

Background: Osteoclastic bone resorption in the compression zone of periodontal ligament (PDL) plays a role in orthodontic tooth movement, and is regulated by the balance of RANKL and OPG. Compression downregulates OPG, conversely, tension upregulates OPG in PDL cells. However, the regulatory mechanism of OPG expression in PDL cells under different mechanical stresses remains unclear. Methods: To study microRNA (miRNA) expression profiles, compression (2g/cm²) or tension (15%-elongation) was applied to immortalized human PDL (HPL) cells, and miRNA was extracted. The miRNA expression was analyzed using a human miRNA microarray, and the changes of the miRNA expression were confirmed by real-time RT-PCR. In addition, miR-3198-mimic and -inhibitor were transfected into HPL cells to understand the resulting OPG expression and production. Results: Certain miRNAs were expressed differentially under compression and tension. Some miRNAs including miR-3198 were upregulated only by compression. Real-time RT-PCR confirmed that compression induced miR-3198, but tension reduced it, in HPL cells. miR-3198-inhibitor upregulated and miR-3198-mimic reduced OPG in HPL cells. miR-3198-inhibitor rescued the compression-mediated downregulation of OPG. On the other hand, miR-3198-mimic reduced OPG expression under tension. Conclusion: We conclude that miR-3198 is upregulated by compression and is downregulated by tension, suggesting that miR-3198 downregulates OPG in response to mechanical stress.

Neuroendocrine tumors (NETs) of duodenal origin are an unusual subset among all NETs, comprising only about 3% of this neoplasm class. In general, NETs are characterized by overexpression of somatostatin receptors and carry an excellent prognosis with early diagnosis and intervention. Chromogranin A (CgA), a protein originating in secretory vesicles of neurons and endocrine cells, has gained wide usage in NET diagnosis and surveillance. Lanreotide is a synthetic octapeptide somatostatin analog with potent anti-proliferative action which has been approved by the FDA (U.S.) and EMA (E.U.) for NET treatment. It is known for its inhibitory effects on growth hormone, serotonin, CgA, and other markers. Here we describe a 56yr-old female with functional NET of duodenal origin, where serum CgA was successfully reduced from 3636 to <100 ng/mL after multidose lanreotide within five months. Of note, no metastatic spread was identified on positron emission tomography/computed tomography with 64Cu-labeled somatostatin analog tracer. Surgical resection of distal antrum, pylorus, and proximal duodenum followed without complication. Histology revealed several foci of well-differentiated tumor cells with characteristic neuroendocrine features and clear surgical margins; low proliferation index (2%) was noted on Ki-67 staining. While select laboratory and imaging modalities are available for diagnosis and monitoring of duodenal NET, this is the first reported therapeutic use of lanreotide in this NET setting. The observed serum CgA attenuation, even before surgery, supports its effectiveness in management of primary nonmetastatic duodenal NET.

Toxin/antitoxin (TA) systems are used primarily to inhibit phage, reduce metabolic activity during stress, and maintain genetic elements. Given the extreme toxicity of some of the toxins of these TA systems, we were curious how the cell silences toxins, if the antitoxin is inactivated or when toxins are obtained without antitoxins via horizontal gene transfer. Here we find that the RalR (type I), MqsR (type II), GhoT (type V), and Hha (type VII) toxins are inactivated primarily by a mutation that inactivates the toxin promoter or via the chromosomal mutations iraM and mhpR.

Although several carbon sequestration methods have been proposed according to theories from various disciplines, it is not known which method is the best. This study evaluated and summarized the advantage and disadvantages of several major carbon sequestration methods, including carbon capture and sequestration, ocean alkalinization, algal cultivation, and wood burial, based on the first principles, namely, sequestration scale and time, elemental stoichiometry, and energy use efficiency. This study suggested that, at present, wood burial may be a leading candidate for carbon sequestration because it can be implemented immediately on a large scale, is cost-effective and efficient, has a long sequestration time, has low technical requirements, and has a relatively low impact on agriculture. This study also discussed the implementation of wood burial from the perspective of nutrient requirements. To achieve carbon neutrality by 2050, the present study proposed a 25-year project starting in 2025 with an average sequestration rate of 3 Pg C per year, which includes burying 1.5 Pg of dead wood carbon and the creation of 9.7 × 10⁶ ha woodland.

The current Global Climate Change, the 2030 Agenda and the Planetary boundaries have driven new development strategies, such as the circular economy, bioeconomy and biorefineries. In this framework, this study analyzes the potential availability and sustainability of the wood supply chain for a small-scale biorefinery aiming at producing 280–300 L of bioethanol per ton dry biomass, consuming 30,000 t of dry biomass per year harvested in a 50 km radius. This wood production goal was assessed from Eucalyptus grandis stands planted for solid wood in northeastern Uruguay. Moreover, to understand the environmental performance of this biomass supply chain, the energy return on investment (EROI), carbon footprint (CF) and potential soil erosion were also assessed. The results showed that the potential wood production would supply an average of 81,800 t of dry mass per year, maintaining the soil erosion below the upper threshold recommended, an EROI of 2.3 and annual CF of 1.22 kg CO_2-eq m^–3 (2.6 g CO_2-eq MJ^–1). Combined with the environmental performance of the bioethanol biorefinery facility, these results would show acceptable values of sustainability according to EU Directive 2009/28/ec because the bioethanol CF becomes 1.7% of this petrol’s CF.

Oriental lacquer, a natural and renewable polymeric coating, comes from the sap produced by lacquer trees. For practical application, oriental lacquer must be refined to reduce excess water and enhance its quality. In this study, drying oils were blended with oriental lacquer during the refining process to prepare an oil-modified refined lacquer (OMRL). The type and adding amount (0, 10, and 20% by wt.) of drying oils for wood coatings utilization were evaluated. Rhus succedanea oriental lacquer is composed of 54.1% urushiols, 34.3% water, 7.2% plant gum, and 4.4% nitrogenous compounds, and drying oils, including tung oil (TO), linseed oil (LO), and dehydrated castor oil (DCO) were used as materials in this study. The results show that the drying oil acts as a diluent, which reduces the viscosity and enhances the workability and could shorten the touch-free drying time and speed up the hardened drying of the OMRL. The results also indicate that the hardness, mass retention, Tg, tensile strength, abrasion resistance, and lightfastness of OMRL films decrease as more drying oils are blended. Conversely, the bending resistance, elongation at break, impact resistance increase, and particularly, the gloss, is greatly improved through the blending of more drying oils. In conclusion, the LO-modified refined lacquer (RL) has the highest film gloss and the DCO-modified RL has the shortest drying time for coating; otherwise, the film properties are similar among the three types of drying oil.

Carbon nanotube (CNT) yarns are fiber-like materials that exhibit excellent mechanical, electrical and thermal properties. More importantly, they exhibit a piezoresistive response that can be tapped for sensing purposes. The objective of this study is to determine experimentally the piezoresistive response of CNT yarns that are embedded in a polymeric medium while subjected to either compression or tension, and compare it with that of the free or unconstrained CNT yarns. The rationale for this study is the need to know the response of the CNT yarn while in a medium, which provides a lateral constraint to the CNT yarn thus mimicking the response of integrated CNT yarn sensors. The experimental program will include the fabrication of samples and their electromechanical characterization. The CNT yarns are integrated in polymeric beams and subjected to four-point bending, allowing the determination of their response under tension and compression. The electrical resistance data from an Inductance-Capacitance-Resistance (LCR) device is used with the data acquired from the mechanical testing system to determine the piezoresistive response of the CNT yarns. This data and information will be used for future modeling efforts and to study the phenomena that occur when CNT yarns are integrated in polymeric and composite materials and structures.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

I deduce an exact and analytic Bianchi type I solution of Einstein’s field equations which generalizes the isotropic ΛCDM universe model to a corresponding model with anisotropic expansion. The main point of the article is to present the anisotropic generalization of the ΛCDM universe model in a way suitable for investigating how anisotropic expansion modifies observable properties of the ΛCDM universe model. Although such generalizations of the isotropic ΛCDM universe model have been considered earlier, they have never been presented in this form before. Several physical properties of the model are pointed out and compared with properties of special cases such as the isotropic ΛCDM universe model. The solution is then used to investigate the Hubble tension. It has recently been suggested that that the cosmic large scale anisotropy may solve the Hubble tension. I consider those earlier suggestions and find that the formulae of these papers lead to the result that the anisotropy of the cosmic expansion is too small to solve the Hubble tension. Then I investigate the problem in a new way, using the exact solution of the field equations. This gives the result that the cosmic expansion anisotropy is still too small to solve the Hubble tension in the general Bianchi type I universe with dust and LIVE (Lorentz Invariant Vacuum Energy with a constant energy density which is represented by the cosmological constant) and anisotropic expansion in all three directions – even if one neglects the constraints coming from the requirement that the anisotropy should be sufficiently small, so that it does not have any significant effect upon the results coming from the calculations of the comic nucleosynthesis during the first ten minutes of the universe. If this constraint is taken into account, the cosmic expansion anisotropy is much too small to solve the Hubble tension.

The estimation of the Hubble constant in the past few decades has increasingly become more accurate with the advance of new techniques. But its value seems to depend on the epoch at which the measurements are made. The Planck estimate of the Hubble constant from the observations of the CMBR in the early Universe is about 67.

We apply principles of Gibbs phase plane chemistry to and across the entire ocean-atmospheric interface. Surface tension increments support a two dimensional, tangential pressure well known to determine rates of bulk gas, bubble, salt, spray and momentum transfer plus both sensible and latent heat fluxes. Hence it is worth asking whether tension mapping follows from current understanding of two dimensional composition. A history is provided dating back centuries and demonstrating that detrital organic macromolecules are central; subtle surfactant functional variation creates a microforcing field which dissipates turbulent energy at the sub-meter scale. Since we have just distributed major biopolymeric classes emitted as primary organic aerosol, further climate links can be established by considering full planar thermochemistry. Organic microlayer behaviors are reviewed with attention to confined, analog phase transitions among two dimensional “solid, liquid, (and) gaseous” states serving as elasticity indicators. We also discuss surfactant properties of general marine dissolved organic carbon, demonstrating that only proteins and lipids are capable of occupying significant local micro-area. The literature often suggests albumin and stearic acid as best proxies, and so we distribute their concentrations through multilevel global ecodynamic simulations. Consensus distributions are obtained in order to control adsorptive equilibria. Working from conservation of planar free energy, a parametric equation of state is devised relating excess coverage to the surface pressure-modulus. Constant settings for the proxy pair are drawn from laboratory study, and they successfully reproduce frequencies for surfactant solid-to-gas occurrence in ambient compression experiments. Functionally resolved organic measurements are rare and so we group them into super-ecological province tables showing that our bulk concentration estimates are reasonable. Outputs are then fed into a coverage-tension-elasticity code. Resulting contours traverse the critical range for piston velocity, bubble-spray and damping effects on either a regional or seasonal basis. There is also a possibility for widespread microlayer crystallization in polar seas. The concepts are a direct extension of our organic aerosol work, and the two approaches could be inserted into Earth System Models in tandem. Uncertainties in the logic are enumerated and include kinetic and thermochemical factors at multiple scales. But the problems are reducible through molecular modeling coupled to renewed laboratory and field study. Connections to marine colloids-gels, microlayer iron chelation, and linings of the ice channel network are discussed additionally.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

Several methods of processing wood into strong, durable products for the construction industry provide transformative opportunities to substitute for less sustainable building materials. Carbon storage is a further advantage, with the added possibility of combustion for bioenergy at end of life. Intense research activity in this area is expected to open up new markets for wood fiber during the lifetime of trees now being planted. Here, wood-derived materials are classified according to the particle size, from metres to nanometres, into which the wood is fragmented before reconstitution. Materials made by densifying or chemically modifying solid wood with no fragmentation are already in production for exterior doors, window frames and cladding, with improved uniformity and stability compared with unmodified wood. Pre-commercial developments promise further gains in durability and strength. Emerging developments extend these process technologies to wood that has been chipped or stranded or pulped, retaining the above advantages over raw timber for weather-facing applications and adding processability by moulding or extrusion. Crucially, the raw material does not then need to be sawn timber but can be bioenergy-grade wood biomass. This will facilitate afforestation strategies that combine the aims of carbon sequestration and biodiversity.

Background: Olecranon fractures are common injuries of the upper limb in adults. Simple dis-placed trasverse fractures are generally surgically treated with tension-band wiring (TBW) or plate fixation (PF). The purpose of this retrospective study is to compare the clinical-functional outcome, complications and reoperation rates between TBW and PF for Mayo IIA fractures. Methods: 72 patients treated with PF or TBW at our institution, completed our survey and clinical evaluation and their demographic and clinical data were recorded and analysed. The clini-cal-functional outcomes were evaluated assessing ROMs and three validated scoring systems: the Disabilities of the Arm, Shoulder, and Hand (DASH), the Mayo Elbow Performance Score (MEPS) and the Patient American Shoulder and Elbow Surgeons Standardized Elbow Assess-ment score (pASES-e). Results: 38 patients (53%) underwent TBW and 34 (47%) PF. The mean DASH, MEPS and pASES-e scores were respectively 14.5±17.2, 80.5±14.7 and 83.6±12.4 in the TBW group and 21±21.7, 75.6±15.3 and 75.1±19.2 in the PF group (p=0.16, p=0.17 and p=0.03). The mean duration of surgery and hospitalisation period were longer in the PF group (p=0.002, p=0.37) whereas the complication and reoperation rates were higher after TBW (p=0.15, p=0.24). Conclusion: According to the literature, both TBW and PF resulted comparable valid surgical op-tions for the treatment of simple isolated displaced olecranon fractures, revealing that they both provide good/excellent outcomes with no significant differences.

The biofibres wide application as mortars enhancement have been so far restricted by factors related to their chemical composition and hygroscopic nature. Their hydrophilic behavior increases the water demand of mortar-mixtures and diminishes their adhesion to the matrix, while further moisture-related fibre degradation issues may arise. Additionally, the natural fibres seem to be susceptible to degradation caused during the exposure to alkaline environments conditions, such as those of cement mortars, restricting their utilization in construction industry. Therefore, the current study focusses on the potential of fibre modification through treatments that would permanently alter their structure and chemical composition in the whole mass or surface towards their performance improvement. In this study, mild hydrothermally treated wood fibres of black pine and beech species were prepared and incorporated in cement mortars to assess their performance, applying the proportion of 1.5% v/v in the mortar. The mortars workability (at fresh state), physical, hygroscopic, chemical, thermal, and mechanical characteristics at the age of 28, 90 and 365 days and weathering performance by subjecting them at different artificial ageing environments (freeze-thaw cycles or outdoor exposure) were examined. The results indicated the beneficial role of the treated fibres in the dimensional stability, flexural strength, thermal insulation properties and capillary absorption of the mortar specimens, especially during ageing process, with the black pine fibres to reveal the highest improvement. The hydrothermally treated wood fibres seem to ensure the integrity maintenance of cement mortars under all ageing conditions, proving that the specific bio-additives could provide low-cost and eco-friendly mortar enhancement pathways.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

Polymer materials are increasingly being used for sliding machine elements due to their numerous advantages. They are used even where they are deformed and in such a state they interact frictionally e.g. in machine hydraulics or lip seals. Few publications deal with the influence of deformation, which is the effect of e.g. assembly on tribological properties of polymeric material. This deformation can reach up to ε ≈ 20% and is achieved without increasing the temperature of the polymer material. The paper presents the results of investigations in which high-density polyethylene (PE-HD) was maintained in deformation by means of a special grip (holder). The wear of the sample was significantly higher than that of the undeformed sample. This effect persisted even after partial relaxation of the stress in the sample after 24 hours. Additional investigations were carried out to explain the obtained results. There were the microscopic observations of the surface after friction, measurements of microhardness and free surface energy. Changes in the value of surface free energy and a significant decrease in microhardness with deformation under tension were observed. Strained material had a different surface appearance after friction and a different size and form of wear products. It was indicated that it is probable that the cohesion of the material will decrease and that the character of the wear process will change as a result of tension. Tension without heating of polymeric material (PE-HD), e.g. as a result of assembly, has been qualified as a hazard to be taken into account when designing and analysing polymeric sliding elements.

Members of the genus Armillaria are widespread forest pathogens against which effective protection has not yet been developed. Due to their longevity and the creation of large-scale cloning of Armillaria individuals, the use of mycoviruses as biocontrol agents (BCAs) against these pathogens could be an effective alternative. This work describes the screening of double-stranded RNA banding patterns as a first approach for potential virus discovery and the use of stranded total RNA-seq for viral detection and characterization in Armillaria spp. collected in the Czech Republic. A total of five single-stranded RNA viruses were detected in Armillaria ostoyae and A. cepistipes, including the first virus of the family Tymoviridae found infecting a member the genus Armillaria and four viruses belonging to the recently described virus group "ambiviruses" with circular ambisense genome organization. Both hammerhead (HHRz) and hairpin (HpRz) ribozymes were detected in all the ambiviricot sequences. Armillaria viruses were compared by phylogenetic analysis and confirmed their specific host by direct RT-PCR, which showed the occurrence of interspecies transmission.

One of the interactions that has been studied in recent decades under the ecohydrological approach is infiltration, which is difficult to determine because the existing methods for estimation depends on certain variables that are difficult to establish or identify, and in other cases, the implementation of instrumentation is expensive. Given this, saturated hydraulic conductivity has been the descriptive variable of the infiltration process by recent authors, being understood as the conduction of water that occurs through the soil and its composition through the vegetation cover. The present design generated an easily accessible portable instrumentation model for the monitoring and collection of infiltration data in situ for basins and ecosystems with different land uses, in an automated manner with the objective of determining the vegetation patterns necessary to sustain the infiltration function. The INDI-INECOL tension infiltrometer [1] was chosen as the reference instrument. It evaluates the saturated hydraulic conductivity based on a column of water that descends through the system and it is exchanged in the soil by the air between the pores. To automate data collection, a measurement system has been proposed through a SCADA system, which is defined as a control, action, decision, storage and data recording system. This system collects field data from a sensor VL053L0X connected to a master station, in our case an Arduino board UNO, connected through the serial port and by a graphical user interface programmed on Python, to display, storage and enrichment of the sensor data and finally to be exported in files suitable for Microsoft Excel.

The difference in the Hubble-Lemaitre constant determined by different probes is a yet unexplained observation. This paper proposes the contention that the tension could be explained by the Doppler shift effect of Ia supernovae or Cepheids, driven by the rotational velocity of their host galaxies relative to the rotational velocity of the Milky Way. While the effect of the Doppler shift is expected to be mild, observations show that it can lead to systematic differences in the apparent brightness, and consequently the estimated distances. A simple experiment is done by repeating a previous analysis. When using the original set of supernovae, $H_o$ is 73.758$\pm$1.943 km/s/Mpc. When using a subset of supernovae such that the host galaxies rotate in the same direction as the Milky Way, $H_o$ drops sharply to 69.049$\pm$3.42 km/s/Mpc, showing a far milder tension with the $H_o$ determined by the CMB. When using a subset of Ia supernovae that rotate in the opposite direction, Ho does not decrease, but instead it increases the Ho tension to 74.182$\pm$3.2. Further analysis will be required to determine the link between Ho observed by using Ia supernovae or Cepheids and the rotational velocity of the host galaxies.

Here we propose a modification of the gravitational field on large scales as an alternate explanation for the discrepancy in the value of the Hubble constant as implied by Planck observations of the CMBR in the early Universe and that deduced from other distance indicators in the present epoch.

The aim of this work is to analyze and investigate the shape preserving properties of ternary 4-point non-stationary interpolating subdivision schemes constructed by Beccari et al. [1] with a tension parameter !k+1 which can reproducing exponential. Moreover, the conditions on the initial control points are developed that allow user to generate shape preserving limit curves after a nite number of subdivision steps and generalize these results in limiting case. Signicance of derived conditions are illustrated through graphs and the whole discussion is followed by examples.

Supported wellbeing centres were set up in UK hospital trusts as an early intervention aimed at mitigating the psychological impact of COVID-19 on healthcare workers. These provided high quality rest spaces with peer-to-peer psychological support provided by National Health Service (NHS) staff volunteers called ‘wellbeing buddies’, trained in psychological first aid. The aim of the study was to explore the views of centre visitors and operational staff towards this COVID-19 workforce wellbeing provision. Qualitative semi-structured interviews were undertaken with twenty-four (20F, 4M) employees from an acute hospital trust in the UK. Interviews were digitally recorded and transcribed, data were handled and analysed using thematic analysis. Interviews generated 3 over-arching themes, and 13 sub-themes covering ‘exposure and job roles’, ‘emotional impacts of COVID-19 and ‘the wellbeing centres’. Supported wellbeing centres were viewed as critical for the wellbeing of hospital employees during the first surge of COVID-19 in the UK. Wellbeing initiatives require managerial advocacy and must be inclusive. Job-related barriers to work breaks and accessing staff wellbeing provisions should be addressed. High quality rest spaces and access to peer-to-peer support are seen to benefit individuals, teams, organisations and care quality. Training NHS staff in psychological first aid is a useful approach to supporting the wellbeing of the NHS workforce during and beyond the COVID-19 pandemic.

Abstract—The static and fatigue analysis of plates with holes, made of 2D woven roving composites, is conducted. The parametrization of convex holes is proposed. Experimental results of specimens without holes and with different shapes of notches are discussed. The fatigue behaviour is considered with the use of the low cycle fatigue method. The analysis is supplemented by the numerical finite element modeling. The present work is an extension of the results discussed in the literature. The finite element modeling of plates with holes is presented in details in Ref [1-3] including also the problems of the accuracy. The experimental results and the form of specimens are shown in Ref [4]. Two parametrical description of static and fatigue behaviour of plates with holes characterizes the goal and the novelty of the paper. The fuzzy approach is employed to reduce the number of experimental data [5].

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

Novel therapies for treatment of familial dilated cardiomyopathy (DCM) are lacking. Triggers for the progression of the disorder commonly occur due to specific gene variants that affect the production of sarcomeric/cytoskeletal proteins. Generally these variants cause a decrease in tension by the myofilaments, resulting in signaling abnormalities within the micro-environment which over time result in structural and functional maladaptations leading to heart failure (HF). Current concepts support the hypothesis that the mutant sarcomere proteins induce a causal depression in the tension time integral (TTI) of linear preparations of cardiac muscle. However, molecular mechanisms underlying tension generation particularly in relation to mutant proteins and their impact on sarcomere molecular signaling, are currently the subject of controversy. Thus, there is a need for clarification as to how mutant proteins affect sarcomere molecular signaling in the etiology and progression of DCM. A main topic in this controversy is the control of the number of tension generating myosin heads reacting with the thin filament. One line of investigation proposes that this number is determined by changes in the ratio of myosin heads in a sequestered super-relaxed state (SRX) or in a disordered relaxed state (DRX) poised for force generation upon Ca-activation of the thin filament. Contrasting evidence from nanometer–micrometer-scale x-ray diffraction in intact trabeculae indicates that the SRX/DRX states may have a lesser role. Instead, the proposal is that myosin heads are in a basal OFF state in relaxation then transfer to an ON state through a mechano-sensing mechanism induced during early thin filament activation and increasing thick filament strain. Recent evidence about the modulation of these mechanisms by protein phosphorylation has also introduced a need for reconsidering control of tension. We discuss these mechanisms that lead to different ideas related to how tension is controlled and disturbed by mutant sarcomere proteins linked to DCM including cardiac myosin, myosin-binding protein C, titin filaments, and thin filaments. Resolving the various mechanisms and incorporating them into a unified concept is crucial for gaining a comprehensive understanding of DCM. This deeper understanding is not only important for diagnosis and treatment strategies with small molecules, but also for understanding the reciprocal signaling processes that occur between cardiac myocytes and their micro-environment. By unraveling these complexities, we can pave the way for improved therapeutic interventions for managing DCM.

To examine the hydrophobicity of torrefied wood fuel, the water resistances of torrefied pellets prepared by two different methods were evaluated using exposure tests under indoor and outdoor conditions. Torrefied pellets from the xylem of Japanese cedar (Sugi, Cryptomeria japonica) and oak (Konara, Quercus serrata) were prepared by two methods: the torrefaction of wood chips followed by pelletization and the pelletization of wood chips followed by torrefaction. It was found that the pellets prepared by pelletization followed by torrefaction had much lower moisture levels than those prepared by the other method and they showed almost no change in diameter after an outdoor weathering test. These characteristics are unique and indicate that the pellets can be applied not only for industrial use but also for residential and commercial purposes.

Seirogan, a wood creosote, is a nonprescription drug used to treat diarrhea. However, reports of its clinical use are rare. Here, we report on the efficacy of wood creosote (3 capsules daily) for the alleviation of diarrheal symptoms in 148 patients from 10 clinics in Japan. The wood creosote capsules were classified as remarkably effective (44 patients), effective (71 patients), and partially effective (13 patients) based on the degree of alleviation of diarrheal symptoms that were induced by a variety of causes. The antidiarrheal efficacy of the capsules did not differ between males and females, and young patients (21–30 years) showed greater improvement in diarrheal symptoms than did old patients (> 61 years). Although this report is based on the re-evaluation of old data that had been preserved by our company, the effectiveness and range of symptoms that were treatable with wood creosote has likely remained unchanged. To the best of our knowledge, this is the first public report on the clinical effectiveness of wood creosote capsules for the treatment of a wide range of diarrheal symptoms.

The extant Keteleeria is endemic to East and Southeast Asia, while it is widely distributed in the northern hemisphere in Earth’s history. In this paper, we reported a novel wood fossil of Keteleerioxylon changchunense Shi, Sun, Meng et Yu sp. nov. collected from the middle member of Yingcheng Formation, Yingcheng Coal Mine, Changchun City, Jilin Province, Northeast China. The quantitative growth-ring analyses of K. changchunense indicate that it was evergreen and its leaf longevity was 1-3 years, which is consistent with the foliar retention of extant Keteleeria. Its high ring markedness index (RMI) indicates that the climate seasonality was pronounced during the early Albian in Songliao Basin, Northeast China. The fossil records of Keteleeria and closely related taxa indicate that this group might originate in Northeast China, spread and migrated northward during the Cretaceous, gradually decreased in the Cenozoic, and so far only survives in East and Southeast Asia.

This contribution was devoted to unveil the strain rate sensitivity (SRS) of G18NiCrMo3-6 cast steel in tension/compression asymmetry. For that purpose, detailed mechanical characterization tests were conducted providing a process window covering quasi-static and medium strain rate regimes (0.001, 0.1, 10 [ s¯¹]) in tension and compression states. By means of this experimental ef-fort, the SRS of the material could be extracted by a function of strain and strain rate which ena-bling to create a mathematical expression to easily be implemented as a state variable for constitu-tive material modeling. Finally, a pressure and rate dependent constitutive material model on the basis of Cocks'89 yield locus definition was created by a subroutine (UMAT) file and the material parameters were verified with respect to the experimental data. The UMAT file also takes into account the tension/compression asymmetry in yielding to handle the effect of porous media plas-ticity concept. The predictions of the proposed material model are quite in line with the experi-mental outputs.

The reconstructive ladder is a well-established concept in Plastic Surgery proposed to achieve wound closure using a stepladder approach from simple to complex procedures and it continues to evolve from when it was presented for the first time. We describe a new surgical technique that allows skin excision and primary wound closure avoiding donor site morbidity from skin grafts and avoiding large scars from loco-regional flaps: the parallelogram excision technique. Fifteen patients with skin lesions underwent this procedure. Six months' follow-up results showed a) good scar healing, b) total excision of lesions, and c) patient acceptance and satisfaction from the usage of this technique. We conducted a geometrical analysis of the parallelogram’s design to study the optimal geometrical condition to achieve all these three factors. We propose that the parallelogram excision of skin lesions proves to be a unique new wound closure technique that may add a new rung to the reconstructive ladder.

There is a confusion in the original design concept for the tensioning of longitudinally connected reinforcement of CRTSII slab ballastless track. In order to clarify the effect of tension value of longitudinal reinforcement on mechanical characteristics of ballastless track, a three dimensional finite element model considering the nonlinear interaction between the track slab and CA mortar of CRTSII slab ballastless track was established. The mechanical characteristics of the track structure under longitudinal tension load and temperature gradient load of the longitudinal joint were calculated. A method of applying pre-stress to post-pouring concrete was proposed according to the concept of pre-stress loss of pretensioning pre-stressed concrete, reasonable tensile force value was proposed after the crack width and the reinforcement stress of the ballastless track in the operation stage were checked and calculated according to the concrete design principle. When the tension force is greater than 300 kN, it’s harmful to the bonding between the slab and mortar layer, which is prone to interlayer damage. In order to adding pre-stress to concrete of wide joints to ensure the longitudinal stability of ballastless track and the reinforcement stress and crack width to meet the design requirements. It is suggested that the tension force value should be 230 kN, and the temperature difference between reinforcement and concrete should be 30 °C before the initial curdle of wide joint concrete.

The objective of this work was to improve the thermal stability, flame resistance and surface properties of black poplar (Populus nigra L.) wood via different impregnation methods. The impregnation method was employed through two distinct modalities: vacuum impregnation and immersion impregnation. Here, poplar wood was impregnated with calcium oxide solutions (1%, 3% and 5%). Fourier transform infrared spectroscopic analysis revealed a shift in the typical peaks of cellulose, hemicellulose, and lignin depending on the impregnation method and solution ratio. Thermogravimetric analysis and the limiting oxygen index indicated that the samples impregnated with lime solutions exhibited higher thermal stability than the unimpregnated wood. In both impregnation methods caused a decrease water absorption and thickness swelling of the sample groups. Using a scanning electron microscope, the effect of the impregnation process on the structure of the wood was examined. In terms of surface properties, it was determined that the surface roughness value increased. On the contrary, it was observed that the contact angle value also increased. A significant difference emerged between the applied methods. In conclusion, the applied lime minerals are suitable substances to increase flame resistance and thermal stability of black poplar wood.

Finishing coatings used in the wood-based composites industry play a key role in the final appearance of the finished product. However, the use of such coatings is not only for aesthetic purposes but also to protect the product against surface damage and moisture or minimize the emission of harmful substances. The latter is an extremely important factor in terms of safety for both the manufacturer and the user, which is why the emissivity test is one of the most important tests in the case of finishing coatings. Such a role can be played by carbon-rich materials, such as those remaining from the extraction of birch bark. In this article, an attempt was made to create coatings in the form of a film by combining a biopolymer with suberinic acid residues (SAR). There were two types of biopolymers used – polylactide (PLA) and polycaprolactone (PCL), in various polymer-SAR ratios. SAR as a residue, is a material that bounds CO2 from the atmosphere and creates a possibility of further use. As part of this study, the obtained coatings were tested in terms of resistance to scratch, relative hardness, cold liquids, total volatile organic compounds (TVOC) and formaldehyde emission, surface absorption etc. Differences in the polymers used and the effect of the SAR additive on selected surface properties were demonstrated. The addition of carbon-rich SAR significantly improves the gas barrier properties of the surface finishing materials based on PLA and PCL. The relative hardness and scratch resistance has also increased with raising SAR content. However, the increasing content of SAR filler act as a limiter in the depth of penetration of deposited surface finishing materials onto the wood surface.

In recent years, laser engraving has received widespread attention as a convenient, efficient, and programmable method, which has enabled the obtaining of high-quality porous graphene from various precursors. Laser engraving is often used to fabricate the dielectric layer with micro-structure for capacitive pressure sensors, however, the usual choice of electrodes remains poorly flexible metal electrodes, which greatly limits the overall flexibility of the sensors. In this work, we propose a flexible capacitive pressure sensor made entirely of thermoplastic polyurethane (TPU) and laser-induced graphene (LIG) derived from wood. The capacitive pressure sensor consisted of a flexible LIG/TPU electrode (LTE), a LIG/TPU electrode with micro hole array, and dielectric layer of TPU with micro-cone array molded from laser-engraved hole array on wood, which provided high sensitivity (0.11 kPa-1), ultra-wide pressure detection range (100Pa to 1.4MPa), fast response (~300 ms) and good stability (&gt;4000 cycles, at 0-35 kPa). We believe that our research makes a significant contribution to the literature because the easily available materials derived from wood and overall consistent flexibility meet the requirements of flexible electronic devices.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

Obesity is a complex chronic disease characterized by excess of body fat. It represents a significant public health problem due to the health-related risk factors. There are growing evidences showing that maternal obesity can program the offspring, which influence neonatal phenotype and predispose offspring to a higher prevalence of metabolic disorders such as obesity. This increased risk may also be epigenetically transmitted across generations. Thus, there is an urgent need to find effective reprogramming approaches in order to resume normal fetal development. Polyphenols are bioactive compounds found in fruits and vegetables that exert their anti-obesity effect through its powerful anti-oxidant and anti-inflammatory activities. Polyphenols supplementation has been proven to counteract the deleterious effects of maternal obesity programming on offspring. Indeed, some polyphenols can cross the placenta and protect the fetal predisposition against obesity. The present review summarizes the effects of dietary polyphenols on obesity-induced maternal reprogramming as an offspring anti-obesity approach.

Platinum(II) complexes have been found to be effective against cancer cells. Cisplatin curbs cell replication by interacting with the deoxyribonucleic acid (DNA), eventually leading to cell death and reducing cell proliferation. In order to investigate the ability of platinum complexes to affect cancer cells, two examples from the class of polyflurophenylorganoamidoplatinum(II) complexes were synthesised and tested on isolated DNA. The two compounds trans-[N,N’-bis(1,2,3,5,6-pentafluorophenyl)ethane-1,2-diaminato(1-)](2,3,4,5,6-pentafluorobenzoato)(pyridine)platinum(II) (PFB), and trans-[N,N’-bis(1,2,3,5,6-pentafluorophenyl)ethane-1,2-diaminato(1-)](2,4,6-trimethylbenzoato)(pyridine)platinum(II) (TMB) were compared with cisplatin through their reaction with DNA. Attenuated Total Reflection Fourier Transform Infrared (ATR-FTIR) spectroscopy was applied to analyse the interaction of the Pt^(II) complexes with DNA in the hydrated, dehydrated and rehydrated state. These were compared with control DNA in acetone/water (PFB, TMB) and isotonic saline (cisplatin) under the same conditions. Principle Component Analysis (PCA) was applied to compare the ATR-FTIR spectra of the untreated control DNA with spectra of PFB and TMB treated DNA samples. Disruptions in the conformation of DNA treated with the Pt^(II) complexes upon rehydration were mainly observed by monitoring the position of the IR-band around 1711 cm^-1 assigned to the DNA base-stacking vibration. Furthermore, other intensity changes in the phosphodiester bands of DNA at ~1234 cm^-1 and 1225 cm^-1 and shifts in the dianionic phosphodiester vibration at 966 cm^-1 were observed. The isolated double stranded DNA (dsDNA) or single stranded DNA (ssDNA) showed different structural changes when incubated with the studied compounds. PCA confirmed PFB had the most dramatic effect by denaturing both dsDNA and ssDNA. Both compounds, along with cisplatin, induced changes in DNA bands at 1711, 1088, 1051 and 966 cm^-1 indicative of DNA conformation changes. The ability to monitor conformational change with infrared spectroscopy paves the way for a sensor to screen for new anticancer therapeutic agents.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

Although the effect of thermal modification (TM) on teak wood color is well documented, a few studies were carried out in closed system processes, as well as it remains unclear the effect of different processes on the same material. This work aimed to verify the effect of closed and open system processes of TM on the color of fast-growing teak wood. Thermally modified wood was evaluated in a closed system at 160 °C (CS160) and in an open system at 185 °C and 210 °C (OS185 and OS210). We measured the moisture content (initial and final) of wood, and the corrected mass loss (CML). The chemical analyses encompassed the contents of alpha-cellulose, hemicelluloses, lignin, and extractives (total, in acetone and dichloromethane). Wood color was measured before and after TM according to the CIEL*a*b* color space. It was possible to achieve the same color using different processes of thermal modification (CS160 and OS210). TM reduced wood lightness (L*), red-green chromaticity coordinate (a*), and yellow-blue chromaticity coordinate (b*). L* and a* had the bigger and lower variations, respectively. The color of thermally modified wood was significantly changed, even at the mildest condition tested (OS185, 0.33% CML).

This review provides an overview of the biotransformation of limonene and α-pinene, which are commonly found in wood residues and citrus fruit by-products, to produce high-value-added products. Essential oils derived from various plant parts contain monoterpene hydrocarbons, such as limonene and pinenes which are often considered waste due to their low sensory activity, poor water solubility, and tendency to autoxidize and polymerise. However, these terpene hydrocarbons serve as ideal starting materials for microbial transformations. Moreover, agro-industrial byproducts can be employed as nutrient and substrate sources, reducing fermentation costs, and enhancing industrial viability. Terpenes, being secondary metabolites of plants, are abundant in byproducts generated during fruit and plant processing. Microbial cells offer advantages over enzymes due to their higher stability, rapid growth rates, and genetic engineering potential. Fermentation parameters can be easily manipulated to enhance strain performance in large-scale processes. The economic advantages of biotransformation are highlighted by comparing the prices of substrates and products. For instance, R-limonene, priced at US$34/L, can be transformed into carveol, valued at around US$530/L. This review emphasises the potential of biotransformation to produce high-value products from limonene and α-pinene molecules, particularly present in wood residues and citrus fruit by-products. The utilisation of microbial transformations, along with agro-industrial byproducts, presents a promising approach to extract value from waste materials and enhance the sustainability of the antimicrobial, the fragrance and flavour industry.

The construction of a house with a stage structure is the uniqueness of Banjarmasin's swampland. Particularly, foundations for swampy terrain necessitate special handling. Building material defects and the basic inability to modify the use and design of wood pillar foundations are the main causes of house building problems. The very limited capacity of a wooden pillar foundation makes house buildings collapse frequently. The aim of the study is to determine the weaknesses of the wooden pillar foundations by examining the indications of damage to the house structure. Field observation investigations, including housing and individual object observations, will be carried out at multiple construction sites in Banjarmasin (Indonesia) as part of this study. The way the data is presented is descriptive. A wooden pillar foundation, which is a frequently used foundation, has a limited load bearing capacity. Because that, there has been no related research that addresses the issue of how this foundation damage. The aim of the study is to determine the early signs of swamp building collapse in the wooden pillar foundations weaknesses by examining the indications of damage to the house structure. The weak construction of a wooden pillar foundation explains some indications of house building damage, such as broken wooden pillars and floor settlement. The existence of evidence that there is a broken 'sunduk’ element is one of the causes of damage to this foundation

To accurately identify high-quality functional wood with superior mechanical properties and enhance its durability, it is imperative to understand the relationships between the physical and mechanical attributes of diverse wood types. Presently, there exist issues related to accuracy, efficiency, and differentiation in studying these performance correlations. The Liang Kleeman (L-K) information flow theory, a causative analytical approach rooted in fundamental physics principles, offers swift computational capabilities. Furthermore, the coefficient of variation in L-K information flow quantitatively gauges the intensity of causal effects. Therefore, this article adopts a causal artificial intelligence perspective and introduces a wood performance analysis method based on L-K information flow.This study focuses on four Chinese fir varieties, including fast-growing Chinese fir (YKS), red heart Chinese fir (CSH, XXH), and iron heart Chinese fir (XXT). By computing and comparing variation coefficients of L-K information flow for various physical properties and their impact on mechanical properties, causal relationships between these properties are elucidated. These findings are then applied to predict wood mechanical properties, achieving a remarkable maximum accuracy of 90%.In the future, these findings will prove invaluable for the selection of high-quality wood and for improving the manufacturing process to prolong the service life of functionalized wood.

Wood is very susceptible to the action of biotic agents. There is a growing interest in the protection of wood and wood artworks to extend their life, using environmentally friendly preservatives. The aim of this paper was the study of nano/siliconate impregnation system for wood protection to control biological colonization. The biotic agents studied have been wood decay fungi. In conclusion, this paper has shown that all the treatments have presented an excellent protective performance against biotic agents. Is important to mention that a synergistic effect can be observed when generating the siliconate/nanoparticle mixtures, resulting in protective systems with excellent efficiency for all the degrading agents. Moreover, it presents an easy application, which represents not only a watertight protective system, but also a set of systems that may be used and managed according to the availability of the active components, the costs, and, most importantly, without having to modify the form of application.

With the continuous improvement of people's quality of life and aesthetics, furniture products have higher requirements. Excellent solid wood chairs are the most representative products in furniture to enhance space and taste and whose design may significantly impact consumers' emo-tional experience and purchase decisions. This study aims to evaluate how the modeling imagery of solid wood chairs affects user preferences and emotional experiences. The development of the current era is inseparable from the analysis of big data. Firstly, a representative sample was ob-tained by multidimensional scaling (MDS), and the sample was analyzed and evaluated by fac-tor analysis. Moreover, five groups of adjective vocabulary were selected to describe the model-ing imagery of solid wood chairs, such as "balanced and coordinated", "unique and novel", "prac-tical and simple", "quality and detailed" and "traditional and plain". Further, the triangular fuzzy theory was applied to analyze and discuss the 12 types of solid wood chairs in the five groups of adjective vocabulary. Then the study verified that the differences in the evaluations of the 12 sam-ples in the "unique and novel" and "quality and detailed" groups were significant, but more minor differences in the groups of "traditional and plain", "balanced and coordinated" and "practical and simple". Through comprehensive comparison, five groups with similar modeling imagery were created, and solid wood chairs with different modeling imagery should be placed in suita-ble spaces. According to the results of this study, the evaluation of the modeling imagery of solid wood chairs can not only rely on subjective judgments but can be reasonably described through data analysis and mathematical algorithms. It can scientifically and effectively reflect the poten-tial perception needs of consumers on the modeling imagery of solid wood chairs, as well as help to improve the design efficiency of the furniture product development stage.

To understand how the thinning strategies impacts on wood quality and quantity for different purposes is of interest, considering that the management of plantations is carried out with parameters that have yet to be validated for different growth conditions. This work evaluated contrasting thinning regimes applied early at two moments of the crop cycle. With an initial population of 840 trees.ha-1, two thinning with populations ranging from 700 to 400, and from 400 to 100 trees.ha-1 were applied at 1.5 and 7.3 years, respectively. Growth analyses were carried out from the ages of 1.5 to 20.8 years considering: total height, diameter at breast height, individual volume, total and commercial volume per hectare, mean annual increase and current annual increase. At final age, contrasting populations of 100, 250 and 400 trees.ha-1 were sampled to assess wood density, and mechanical properties (bending and compression on small scale clear samples). The values of individual growth and wood properties are related to a Stand Density Index to understand the effect of competition on those values. The results allow us to identify the thinning schemes that record the most significant individual and per-hectare growth (both in thinning and clear felling) and the optimal harvest time under specific growth conditions. We assessed the proportions of commercial logs for sawmill and pulp uses, providing valuable inputs for a subsequent economic analysis of thinning regimes seeking for the most convenient combination of wood products. Wood's physical and mechanical properties assessed were barely affected by contrasting levels of competition between trees, therefore the decision of the silvicultural system to implement will depend on production and economic criteria.

An enormous interest in the development of efficient protocols for cellulose extraction has been demonstrated in the last years, however, they were usually based on non-sustainable chemical and thermal approaches. In this work we describe a new and more sustainable method for cellulose extraction from eucalyptus and pine tree wood waste products exclusively performed using microwave-assisted radiation. The methodology includes 3 main steps: i) alkaline treatment; ii) bleaching I, using H2O2; and iii) bleaching II, an acidic treatment. Samples obtained in each step were characterized by Fourier-transform Infrared (FTIR) spectroscopy, powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results were compared with those of starting materials, with the commercially available microcrystalline cellulose and with an industrial paper pulp. Results confirmed that for both type of wood wastes, cellulose was retained during the extractions procedures and that the removal of hemicellulose was achieved at the last step as seen by the FTIR spectra and TGA curves. The developed protocol is innovative since it constitutes an easy and quick approach to extract cellulose, from eucalyptus and pine tree wood waste using mild chemical and thermal conditions, microwave irradiation, and environmentally friendly purification steps. This approach offers the possibility of a future scale-up study to potentially apply the develop protocol to the extraction of cellulose in an industrial scale.

Nails are a simple and viable solution to connect sections of wooden structures. Although they are the oldest and most traditional connection elements there is a considerable knowledge gap concerning the use of larger sized, threaded nails, in tropical hardwoods. The objective of this project was to evaluate the effect of different nail models and diameters on the withdrawal resistance of Allantoma decandra wood and verify the efficiency of the existing nail withdrawal resistance prediction equations. Withdrawal tests were carried out using three nail models (smooth, helical, and annular), of two different diameters (2.8 mm and 3.5 mm). For each combination, ten Allantoma decandra wood specimens were used. Four nails were inserted 3.2 mm into each wood specimen and then withdrawn using a universal testing machine with 600 kN capacity, according to the procedures of ASTM D-143-2014. The nail model was the most relevant factor in this study, having a direct influence on withdrawal resistance. Annular nails presented the highest resistance values, followed by helical and smooth nails. The nail diameter had no significant effect on the maximum load result. The equations for withdrawal resistance prediction demonstrated considerable accuracy regarding the experimentally obtained data, being important tools to anticipate the behavior of wooden structures.