The effect of doublet state metalloradical complex in a solar cell inside the common active layer poly(3-hexylthiophene)/ [6,6]-phenyl-C61-butyric acid methyl ester (P3HT/PC60BM) is explored. In this work is demonstrated that the role of the Bis-[1,3-Bis-(2,6-diisopropylphenyl)-4,5-dichloroimidazol-2-ylidene]palladium(I) hexafluoridophosphate dopant, [Pd(IPrCl)2][PF6], is crucial because, by having a stable unpaired electron in the molecule, it significantly improves the optoelectronic performance of the devices. We found the optimal concentration of this molecule in the active layer, and we demonstrated that the presence of this additive in the active layer helps to significantly improve the morphology of the device. The improvements in optoelectronic and morphological parameters are associated with a remarkable increase of photocurrent generation due to more favourable mechanisms of charge separation at the donor/acceptor (D/A) interfaces of the active layer and reduced recombinations. Moreover, the presence of this additive improves the stability of the unencapsulated solar cell against photochemical degradation produced by sunlight.

Two gallium porphyrins, a tetraphenyl GaCl porphyrin, termed as (TPP)GaCl, and an octaethylporphyrin GaCl porphyrin, termed as (OEP)GaCl were synthesized to use as electron cascade in ternary organic bulk heterojunction films. A perfect matching of both gallium porphyrins energy levels with that of poly(3-hexylthiophene-2,5-diyl) (P3HT) or poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) polymer donor and the 6,6-phenyl C71 butyric acid methyl ester (PCBM) fullerene acceptor forming an efficient cascade system that could facilitate electron transfer between donor and acceptor was demonstrated. Therefore, ternary organic solar cells (OSCs) using the two porphyrins in various concentration were fabricated, where a performance enhancement was obtained. In particular, (TPP)GaCl-based ternary OSCs of low concentration (1:0.05 vv%) exhibited a ~17 % increase of the power conversion efficiency (PCE) compared with the binary device due to improved exciton dissociation, electron transport and reduced recombination. On the other hand, ternary OSCs with the (TPP)GaCl of high concentration (1:0.1 vv%) and (OEP)GaCl (1:0.05 and 1:0.1 vv%) showed poorest efficiencies due to very rough nanomorphology and suppressed crystallinity of ternary films when the GaCl porphyrin introduced in the blend, as revealed from X-ray diffraction (XRD) and atomic force microscopy (AFM). The best performed devices exhibited also improved photostability, when exposed to sunlight illumination for a period of 8 h than the binary OSCs, attributed to the suppressed photodegradation of the ternary (TPP)GaCl 1:0.05-based photoactive film.

We revisit the argument that link the efficiency of a solar cell to its reverse operation as a LED, in the case where the material is organic. In organic cells, exciton transport is an intermediate process between sunlight absorption and the generation of electric current. We show that quenching exciton radiation can be beneficial to cell efficiency, without contradicting the general rule prevailing for semiconductor cells. Our treatment allows us to discuss both bulk heterojunction and planar junctions.

In the past decade, considerable efforts have been devoted to the development of semitransparent organic solar cells. Numerous materials and architectures have been proposed for the future commercialization of these devices. Among these, the use of ternary active layers demonstrated a great promise for the development of efficient semi-transparent organic solar cells with the potential for future applications including self-powered greenhouses and powered windows. Researchers seek alternative solutions to the trade-off between device power conversion efficiency (PCE) and average visible transmittance (AVT), with photoactive materials being the key parameters that govern both (PCE) and (AVT) as well as device stability. Several new organic materials, including polymers and small molecules, were synthesized, and used in conjunction with a variety of techniques to achieve semitransparent conditions. In this review paper, we will look at the working principle and key parameters of semi-transparent organic solar cells, as well as the methods that have been used to improve the performance of ternary-based semi-transparent organic solar cells. The main approaches were concluded to be spectral enhancement and transparency increment of the active layer through bandgap tuning, utilizing novel organic semiconductors, and design architecture of the active layers.

The efficiency of organic solar cells (OSCs) is influenced by various factors, among which environmental temperature plays a significant role. Previous studies have shown that the thermal stability of these cells can be enhanced by incorporating a third component into their structure. Ternary organic solar cells, in particular, have shown promising results in improving thermal stability. A well-designed electron transport layer (ETL) can significantly bolster thermal stability by facilitating efficient charge transport and reducing charge recombination. In this study, we investigated the effect of temperature on the efficiency of inverted ternary structures, ranging from 300 K to 400 K. The structures examined include FTO/SnO2/PM6:D18:L8-BO/PEDOT: PSS/Ag, FTO/Spiro-OMeTAD/PM6:D18:L8-BO/PEDOT: PSS/Ag, and FTO/PC60BM/PM6:D18:L8-BO/PEDOT: PSS/Ag. Through simulations employing three different electron transport layers—SnO2, Spiro-OMeTAD, and PC60BM—we observed that at 340 K (65°C) these structures maintained 92% of their original high efficiency of ~20% at 300 K, which represents a high level of thermal stability under the high PCE condition.

The organic solar cells (OSCs) have drawn attention in the past decade due to its cynosure in industrial manufacturing because of its promising properties such as low weight, highly flexible and low cost production. However, low η restricts the utilization of OSCs for potential application such as low cost energy harvesting devices. In this paper, OSCs structure based on triple junction tandem scheme is reported with three different absorber materials with the objective to enhance the absorption of photons which in turn improves the η, as well as its correlating performance parameters. The investigated structure gives the higher value of η = 14.33% with Jsc=16.87 (mA/m2), Voc=1.0 (V), and FF=84.97% by utilizing a stack of three different absorber layers with different band energies. The proposed structure is tested under 1.5 (AM) with 1 sun (W/m2). The impact of top, middle and bottom sub cells thickness on η is analyzed with a terse to find the optimum thickness for three sub cells to extract high η. The optimized structure is then tested with different electrode combination and the highest η is recorded with FTO/Ag. Moreover, the influence of upsurge temperature is also demonstrated on the proposed structure and observed that the upsurge temperature has greatly affected the electrical parameters of the device and η decreases from 14.33% to 11.40% when the temperature of the device rises from 300-400 K.

A novel solution-processed graphene-based material was synthesized by treating graphene oxide (GO) with 2,5,7-trinitro-9-oxo-fluorenone-4-carboxylic acid (TNF-COOH) moieties, via simple synthetic routes. The yielded molecule N-[(carbamoyl-GO)ethyl]-N’-[(carbamoyl)-(2,5,7-trinitro-9-oxo-fluorene)] (GO-TNF) was thoroughly characterized and it was shown that it presents favorable highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels to function as a bridge component between the polymeric donor poly({4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl}{3-fluoro-2-[(2-ethylhexyl)carbonyl] thieno[3,4-b]thiophenediyl}) (PTB7) and the fullerene derivative acceptor [6,6]-phenyl-C₇₁-butyric-acid-methylester (PC₇₁BM). In this context, a GO-TNF based ink was prepared and directly incorporated within the binary photoactive layer, in different volume ratios (1-3% ratio to the blend), for the effective realization of inverted ternary organic solar cells (OSCs) of the structure ITO/PFN/PTB7:GO-TNF:PC₇₁BM/MoO₃/Al. The addition of 2% v/v GO-TNF ink led to a champion power conversion efficiency (PCE) of 8.71% that was enhanced by ~13% as compared to the reference cell.

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.

We demonstrated an ITO-free, highly transparent organic solar cell with the potential to be integrated into window panes for energy harvesting purposes. A transparent, conductive ZnO/Ag/ZnO multilayer electrode and a Ag:Ca thin film electrode were used in this transparent device as the bottom and top electrode, respectively. To further improve the transmittance of the solar cell, the thickness of the top ZnO layer was investigated by both experiment and simulation. An average visible transmittance of > 60% was reached, with a maximum transmittance of 73% at 556 nm. Both top and bottom illumination of the solar cell generated comparable power conversion efficiencies, which indicates the wide application of this solar cell structure. In addition, we fabricated distributed Bragg reflector mirrors with sputtered SiO2 and TiO2, which efficiently increased the power conversion efficiency over 20% for the solar cells on glass and PET substrates,

The month of May 2024 was characterized by solar energetic particles events directed towards the Earth, especially the big event causing a strong terrestrial geomagnetic storm during the night from 10 to 11 May 2024, with auroras observed everywhere in Europe. This was the strongest storm for the last 20 years with a Dst < -400 nT. In the present work, we show with observations of GOES, PROBA-V/EPT and MetOP/MEPED that this exceptional event was associated with the injection of energetic protons in the proton radiation belt, with important consequences for the South part of the South Atlantic Anomaly (SAA). In addition, the geomagnetic storm caused by the solar eruption has had tremendous impacts on the electron radiation belts. Indeed, we show that for 0.3 to 1 MeV electrons, the storm led to a long lasting four belts configuration which was not observed before with EPT launched in 2013, until a smaller geomagnetic storm on June 15 took place. Moreover, for the first time since its launch, observations of the EPT show that ultra-relativistic electrons with E>2 MeV have been injected into the inner belt until L=2.4, violating the impenetrable barrier previously estimated to be located at L=2.8.

We propose a new approach to extending the notion of commutator and Lie algebra to algebras with ternary multiplication laws. Our approach is based on ternary associativity of the first and second kind. We propose a ternary commutator, which is a linear combination of six (all permutations of three elements) triple products. The coefficients of this linear combination are the cube roots of unity. We find an identity for the ternary commutator that holds due to ternary associativity of the first or second kind. The form of the found identity is determined by the permutations of the general affine group GA(1,5)⊂S5. We consider the found identity as an analogue of the Jacobi identity in the ternary case. We introduce the concept of a ternary Lie algebra at the cubic root of unity and give examples of such an algebra constructed using ternary multiplications of rectangular and three-dimensional matrices. We point out the connection between the structure constants of a ternary Lie algebra with three generators and an irreducible representation of the rotation group.

Visible-light photocatalysis, particularly in its application to organic synthesis, has experienced a big renaissance in the past decade. The rational design of new photocatalysts with designed and improved photocatalytic properties, that at the same time circumvents the necessity of using scarce and toxic transition metals, will predictably play a key role in photocatalysis in the next few years. Although free-base porphyrins were identified some years ago as a promising, easily accessible and easily tunable class of organic photoredox catalysts, a systematic study on the effect of the electronic nature and of the position of the substituents on both the ground-state and the excited-state redox potentials of these compounds is still lacking. We have prepared a set of known functionalized derivatives of meso-tetraphenyl porphyrin containing different substituents either in one of the meso-positions or at a beta-pyrrole carbon and we have determined their ground- and (singlet) excited-state redox potentials. This survey has led us to conclude that the introduction of a carbonyl group at the beta-pyrrolic position strongly increases the facility of the monoelectronic reduction of the porphyrin both in the ground state and in the singlet excited state. We have also prepared a second set of four previously unknown benzoyl derivatives of meso-tetraphenylporphyrin, and we have confirmed the validity of our conclusions.

The reaction of 2-((diphenylmethylene)amino)acetonitrile with (E)-1-phenyl-3-(thiophen-2-yl)prop-2-en-1-one was performed by using 33% NaOH in CH3CN for 30 min at 0°C. The main product - rel-(2R,3S)-2-((diphenylmethylene)amino)-5-oxo-5-phenyl-3-(thiophen-2-yl)pentanenitrile was isolated and characterized by IR, 1H NMR, 13C NMR and high-resolution mass spectrometry (HRMS).

Nose mask is a fomite and its usage was mandatory during the COVID-19 outbreak. Its effectiveness has been established; however, as a fomite, it can harbor opportunistic respiratory pathogens such as Streptococcus spp., which could complicate COVID-19 infections. This study profiled Streptococcus species resident on nose masks obtained from consenting participants. Phenotypic assays and 16S rRNA sequencing were used to identify Streptococcus spp. resident on the interior and exterior of 100 nose masks analyzed. Antibiotic resistance (AMR) was determined with disc diffusion and broth microdilution assays. AMR and virulence makers were profiled with primer-specific PCR amplification. 23% of the analyzed samples had Streptococcus isolates. The isolates were highly resistant to the antimicrobials, including conventional, last-resort antibiotics, disinfectants and antiseptics. All the isolates are multidrug resistant with 80-100% levels of AMR to the 16 antibiotics tested with a Multiple-Antibiotic Resistance index greater than 0.2, indicative of potential pathogens. The isolates harbored tetB, ermB, pbp2B, pbp2b1 (resistance) and lytA, lytA1, ply1, cbpA, lytA, pavA (virulence) markers, which might constitute a serious public health risk. Overall, the study emphasizes the need to assess mask usage and the risks associated with opportunistic pathogens that are resident on frequently used nose masks in the COVID-19 era.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

Shigella and Salmonella have been implicated in neonatal sepsis, food poisoning, and bacteremia. Their increasing resistance to antibiotics has undermined treatment options, constituting a public health crisis. Also, the scarcity of new antibiotics in the development pipeline compounds multidrug-resistance (MDR). Hence, there is a need to potentiate antibiotics to mitigate resistance. This study leveraged riboflavin to re-sensitize fluoroquinolones and carbapenems against MDR Shigella and Salmonella spp. Disk diffusion, microbroth-dilution, chequerboard, and time-kill assays were used to determine resistance profiles and riboflavin-antibiotic activity. Biofilm-formation and bacterial viability (after riboflavin-antibiotic challenge) was determined with crystal-violet and Macrophage infection assays, respectively. Strains exhibited &gt;80% resistance to fluoroquinolones and carbapenems, with 160–320 µg MIC ranges and 0.5–2 FIC, indicating no synergy. At 40–80 µg riboflavin, there was two-fold reduction in bacterial survival, with meropenem-riboflavin exhibiting significant reduction and FIC of 0.075 indicating high synergistic activity. Biofilm-formation was altered (from strong to weak phenotype) with 40 µg riboflavin-antibiotic treatment. There was a 40–70% reduction in bacterial survival in THP-1 cells treated with meropenem-riboflavin after 3 hours, and complete clearance between 24-48 hpi. Riboflavin potentiated fluoroquinolones and meropenem, leading to modulation of the host immune response for the clearance of the strains.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

Transparent conductive electrodes (TCEs) are of enormous significance to the emergence of flexible and wearable electronics and continued growth of modern devices. Versatile and tunable TCEs, featuring with not only high optical transmittance but also intriguing features of electrochemical energy-storage capability, remain a significant challenge. Here we develop capacitive active films comprised of graphene-conjugated V2O5@poly (3,4-ethylene dioxythiophene) ternary composite (V2O5@PEDOT/rGO) on silver nanowire coated substrates as solid-state super/pseudocapacitors. The constructed electrodes exhibit improved electrolyte ions interaction with effective graphene layer, achieving high areal capacitance 0.6-1.2 mF.cm−2 with 0.5M LiCl electrolytes at optical transparency >60% with record durability. As demonstrated, the kinetic blocking of PEDOT layer and anchoring capability of graphene upon amphoteric soluble vanadium ions from layered V2O5 nanoribbons/nanobelts contribute synergistically to the unusual electrochemical stability, also shown using scanning electrochemical microscopy (SECM) providing electroactivity sites and ion transportation rates. As-fabricated symmetric solid-state supercapacitors delivered broad potential window >1.4 V under two different electrolyte environments (aqueous LiCl and LiCl/PVA gel) and demonstrated higher power and energy density (0.27 μWh.cm−2) outperforming previously reported devices at <0.1 μWh.cm−2. The electrochemical properties are also discussed in terms of solvation in polymer gel electrolyte ions.

Photovoltaic is one of the promising renewable sources of power to meet the future challenge of energy need. Organic and perovskite thin film solar cells are an emerging cost-effective photovoltaic technology because of low-cost manufacturing processing and a light-weight. The main barrier of commercial use of organic and perovskite solar cells is the poor stability of devices. Encapsulation of these photovoltaic devices is one of the best ways to address this stability issue and enhance the device lifetime by employing materials and structures that possess high barrier performance for oxygen and moisture. The aim of this review paper is to find different encapsulation materials and techniques for perovskite and organic solar cells according to the present understanding of reliability issues. It discusses the available encapsulate materials and their utility in limiting chemicals such as water vapour, oxygen penetration. It also covers the mechanisms of mechanical degradation within the individual layers and solar cell as a whole, and possible obstacles to their application in both organic and perovskite solar cells. The contemporary understanding of these degradation mechanisms, their interplay and their initiating factors (both internal and external) are also discussed.

This review proposes an overview on the use of organic functionalized carbon nanostructures (CNSs) into solar energy conversion schemes. Our attention has focused in particular on the contribution given by organic chemistry to the development of new hybrid materials that find application in dye sensitized solar cells (DSSC), organic photovoltaics (OPV), perovskite solar cells (PSC) and also in photocatalytic fuel production, focusing in particular on the most recent literature. The request for new materials able to accompany the green energy transition that are abundant, low cost, with low toxicity, from renewable sources has further increased the interest in CNSs that meet all these requirements. The inclusion of an organic molecule, thanks to both covalent and non-covalent interactions, into a CNS, leads to the development of a completely new hybrid material able of combining and improving the properties of both starting materials. Besides the numerical data, which unequivocally state the positive effect of the new hybrid material, we hope that these examples can be inspiring for further research in the field of photoactive materials from an organic point of view.

This study presents the first genome assembly of the freshwater saprobe fungus Neonectria lugdunensis and a comprehensive phylogenomics analysis of the Nectriaceae family, examining genomic traits according to fungal lifestyles. The Nectriaceae family, one of the largest in Hypocreales, includes fungi with significant ecological roles and economic importance as plant pathogens, endophytes, and saprobes. The phylogenomics analysis identified 2684 single-copy orthologs, providing a robust evolutionary framework for the Nectriaceae family. We analyzed the genomic characteristics of 17 Nectriaceae genomes, focusing on their carbohydrate-active enzymes (CAZymes), biosynthetic gene clusters (BGCs), and adaptations to environmental temperatures. Our results highlight the adaptation mechanisms of N. lugdunensis, emphasizing its capabilities for plant-litter degradation and enzyme activity in varying temperatures. Comparative genomics of different Nectriaceae lifestyles revealed significant differences in genome size, gene content, repetitive elements, and secondary metabolite production. Endophytes exhibited larger genomes, more effector proteins, and BGCs, while plant pathogens had higher thermo-adapted protein counts, suggesting greater resilience to global warming. In contrast, the freshwater saprobe shows less adaptation to warmer temperatures and is important for conservation goals. This study underscores the importance of understanding fungal genomic adaptations to predict ecosystem impacts and conservation targets in the face of climate change.

The reduction of PV prices and interest in energy independence accelerate the adoption of residential battery storage. This storage can support various functions of an energy system undergoing decarbonization. In this work, operative benefits of the storage from the system perspective, namely, generation cost reduction and congestion mitigation, are investigated. Germany is chosen as a case study due to its strong reliance on variable renewable energy. For the analysis, an economic dispatch model with a high spatial resolution is coupled with a Pan-European transmission grid model. It is shown that the system's generation costs are highest when the assets are used only to maximize the PV self-consumption, and the costs are lowest when the storage also reacts to the market dynamics. This amounts to 6% cost reduction. Both operation strategies result in an equal level of grid congestion and infrastructure loading. This is improved with a strategy that accounts regional peak reduction as a secondary objective. The high congestion level emphasizes the grid expansion need to keep pace with the generation and electrification expansion necessary to decarbonize other sectors. Lastly, policymakers should enable multipurpose utilization, e.g., via the introduction of market-oriented retail electricity prices with intervention options for grid operators.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Hydrogen is the lightest atom and composes roughly half of the atomic content in macromolecules, yet their location can only be inferred or predicted in most macromolecular structures. This is because hydrogen can rarely be directly observed by the most common structure determination techniques (such as X-ray crystallography and electron cryo-microscopy). However, knowledge of hydrogen atom positions, especially for enzymes, can reveal protonation states of titratable active site residues, hydrogen bonding patterns, and the orientation of water molecules. Though we know they are present, this vital layer of information, which can inform a myriad of biological processes, is frustratingly invisible to us. The good news is that, even at modest resolution, neutron crystallography (NC) can reveal this layer and has emerged this century as a powerful tool for elucidating enzyme catalytic mechanisms. Due to its strong and coherent scattering of neutrons, incorporation of deuterium into the protein crystal amplifies the power of NC. This is especially true when solvation and the specific participation of key water molecules are crucial for catalysis. Neutron data allow the modeling of all three atoms in water molecules and have even revealed previously unobserved and unique species such as hydronium (D3O+) and deuteroxide (OD-) ions as well as lone deuterons (D+). Herein, we briefly review why neutrons are ideal probes for identifying catalytically important water molecules and these unique water-like species, limitations in interpretation, and four vignettes of enzyme success stories from disparate research groups. One of these groups was that of Dr. Chris G. Dealwis, who died unexpectedly in 2022. As a memorial appreciation of his scientific career, we will also highlight his interest and contributions to the neutron crystallography field. As both the authors were mentored by Chris, we feel we have a unique perspective on his love of molecular structure and admiration for neutrons as a tool to query those structures.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

A number of standard molecules are used for the molecular and histological characterization of lymphatic endothelial cells (LECs) such as Lyve1, Podoplanin (D2-40), VEGFR3, Prox1 and CD31. The number of molecules whose mutations cause lymphatic malformations or primary congenital lymphedema is considerable, but the majority of these diseases have not yet been characterized at the molecular level. Therefore, there is still considerable scope for molecular and functional studies of the lymphatic vasculature. Using RNASeq, we have previously characterized LECs under normoxic and hypoxic conditions. We used this information to compare it with immunohistochemical data. We carried out some of the immunohistology ourselves, and systematically studied the Human Protein Atlas (https://www.proteinatlas.org/). Here we describe molecules that are expressed at RNA and protein levels in LECs, hoping to stimulate future functional studies of these molecules.

Cell-culture meat is a novel concept to replace traditional meat produced from animals, and to satisfy rising food demands due to the world population growth. It is still a young field and requires to solve technical issues including cell sources and types, efficient culture for large scale production, taste and texture for customer satisfaction. The current review summarized traditional beef meat production and evaluation methods for customer satisfaction. In particular, serum biomarkers for beef meat evaluation are discussed, which can be applicated for cell-culture meat production.

Wood-borer extermination by a dry heat clean-up is the essential method from the point of view of sustainability of historical wooden structures like trusses and ceilings in heritage-listed buildings. The wooden components are heated by a hot air of temperature about 100°C until the temperature in the centre of the wooden structures reaches 55°C to kill the wood-borers. In this article we review the method and present solution of the heat equation for structural wooden components. We also suggest an approximate formula that enables to estimate the necessary heating time for different cross sections of wooden components and can be used in technical application of the method.

Reconstructing the Tree of Life remains a central goal in biology. Early methods, relying on small numbers of morphological or genetic characters, often yielded conflicting evolutionary histories, undermining confidence in the results. Investigations based on phylogenomics, which use hundreds to thousands of loci for phylogenetic inquiry, have provided a clearer picture of life's history, but certain branches remain problematic. To resolve difficult nodes on the Tree of Life, two recent studies tested the utility of synteny, the conserved collinearity of orthologous genetic loci in two or more organisms, for phylogenetics. Synteny exhibits compelling phylogenomic potential while also raising new challenges. We identify and discuss specific opportunities and challenges that bear on the value of synteny data and other rare genomic changes for phylogenomic studies. Synteny-based analyses of highly contiguous genome assemblies mark a new chapter in the phylogenomic era and the quest to reconstruct the Tree of Life.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

The study of biologically active substances from natural sources shows the prospect of obtaining a new type of antimicrobial agents, highly effective against pathogenic microorganisms and non-toxic to humans. Our study reveals for the first time that Cornu aspersum mucus has the potential to act as a source of antibacterial agents against bacterial pathogens such as Bacillus cereus 1085, Propionibacterium acnes 1897, Salmonella enterica 8691, Enterococcus faecalis 3915, and Enterococcus faecium 8754. Both mucus fractions with MW<20 kDa and MW>20 kDa showed antimicrobial activity and antioxidant properties that’s why they can be turned into an alternative agent to expensive synthetic antibacterial compounds. Using de novo sequencing 16 novel peptides with potential antibacterial activity were identified by in a fraction with MW<20 kDa. The results of electrophoretic and proteomic analysis of mucus fraction with MW >20 kDa presented proteins with potential antibacterial activity highly homologous to hemocyanins, mucus protein Aspernin, lectins, L-amino acid oxidase-like protein, and mucins (mucin-5AC, mucin-5B, mucin-2 and mucin-17). Thanks to the synergistic action of the bioactive components, the mucus fraction with MW > 20 kDa in low concentrations per 8–2 µg/mL showed promising antimicrobial activity against the tested bacteria, comparable to Vancomycin and without unwanted cytotoxic effects against non-target cells. Additionally, C. aspersum mucus fractions were found to have a positive effect on eukaryotic organisms by reducing the levels of intracellular oxidative damage and increasing the antioxidant capacity of the cell. These findings could serve as a basis for the development of a potent non-cytotoxic antibacterial agent to replace conventional antibiotics and avoid the development of antibiotic resistance.

This study presents the development of a diglycidyl monomer containing two imine groups that can act as dynamic and reversible bonds. During the curing of the monomer with two different amine hardeners, we confirmed the formation of new imine groups due to the transamination reaction, not reported before, between the imine groups of the diepoxy monomer with the amine groups of the hardener. The effect of this structural change is observed for the first time in the stress relaxation behavior, resulting in the overlapping of two different relaxation modes. The analytical modelling could extract two distinct characteristic relaxation times using a double-element Maxwell model. A second characterization of the stress relaxation process by frequency sweep experiments was performed to corroborate the results obtained, confirming speedy stress relaxation. Acid-catalyzed hydrolysis was performed on the studied materials, demonstrating the complete degradation of the network. We finally confirmed that the synthesized diepoxy compound is suitable for preparing carbon fiber-reinforced composite materials, demonstrating easy fiber impregnation, fast reshaping and especially a total degradation of the polymer matrix that allows the recovery of the carbon fibers in mild conditions. This epoxy-amine system is an excellent candidate for overcoming the traditional limits of thermosets in preparing fiber-reinforced composites.

Mesenchymal stem cells (MSCs) hold immense therapeutic potential due to their regenerative and immunomodulatory properties. However, to utilize this potential, it is crucial to optimize their in vitro cultivation conditions. Three-dimensional (3D) culture methods using cell-laden hydrogels aim to mimic the physiological microenvironment in vitro, thus preserving MSC biological functionalities. Cellulosic hydrogels are particularly promising due to their biocompatibility, sustainability, and tunability in terms of chemical, morphological, and mechanical properties. This study investigated the impact of (1) two physical crosslinking scenarios for hydrogels derived from anionic cellulose nanofibers (CNF) used to encapsulate adipose-derived MSCs (adMSCs) and (2) physiological culture conditions on the in vitro proliferation, differentiation, and extracellular vesicle (EV) production of these adMSCs. Our results revealed that additional Ca2+-mediated crosslinking, intended to complement self-assembly and gelation of aqueous to-CNF in the adMSC cultivation medium, adversely affected both the mechanical properties of the hydrogel spheres and the growth of the encapsulated cells. However, cultivation under dynamic and hypoxic conditions significantly improved the proliferation and differentiation of the encapsulated adMSCs. Furthermore, we demonstrated that adMSCs in CNF hydrogel spheres exhibited potential for scalable EV production with potent immunosuppressive capacities in a bioreactor system. These findings underscore the importance of physiological culture conditions and the suitability of cellulosic materials for enhancing the therapeutic potential of MSCs. Overall, our study provides valuable insights for optimizing the in vitro cultivation of MSCs for various applications, including tissue engineering, drug testing, and EV-based therapies.

Pulmonary hypertension (PH) is a progressive and potentially fatal complication of sickle cell disease (SCD) affecting 6-10% of adult SCD patients. Various mechanisms and theories have been evaluated to explain the pathophysiology of the disease. However, questions remain, particularly regarding the clinical heterogeneity of the disease in terms of symptoms, complications, and survival. Beyond the classical mechanisms that have been thoroughly investigated and include hemolysis, nitric oxide availability, endothelial disorders, thrombosis, and left heart failure, attention is focused nowadays on the potential role of the genes involved in such processes. Potential candidate genes are investigated through next-generation sequencing, with the TGF-β pathway being the initial target. This field of research may also provide novel targets for pharmacologic agents in the future as is already the case with idiopathic PH. The collection and processing of data and samples from multiple centers can yield safe results that will allow a better understanding of SCD-related PH as a part of the disease’s clinical spectrum. The following review attempts to capture the most recent findings of studies on gene polymorphisms that have been associated with PH in SCD patients.

Music has the innate potential to reach all parts of the brain, stimulates certain brain areas which are not achievable through other modalities. Music Therapy (MT) is being used for more than a century to treat individuals who needs personalized care. MT optimizes motor, speech and language responsibilities of the brain and improves cognitive performance. Pervasive developmentdisorder (PDD) is a multifaceted, neuro developmental disorder and autism spectrum disorder (ASD) comes under PDD, which is defined by deficiencies in three principal spheres: social connection with others, communicative and normal movement skills. The conventional imaging studies illustrate reduced brain area connectivity in people with ASD, involving selected parts of the brain cortex. People with ASD express much interest in musical activities which engages the brain network areas and improves communication and social skills.The main objective of this review is to analyze the potential role of MT in treating the neurological conditions, particularly ASD. Evidence based studies have reported the extensive therapeutic application of music on various part of the brain in a nonverbal child with autism through hearing or making music.Hence we hypothesized that MT intervention can improve the communication capacity in people with ASD, than customary neurorestoration therapy alone.

Developing low-cost and stable materials for converting solar energy into electricity is vital in meeting the world's energy demand. Metal-organic frameworks (MOFs) have gained attention for solar cells due to their natural porous architectures and tunable chemical structures. This review commences with an exploration of the synthetic methods of MOFs. Moreover, we discuss the various roles of MOFs, including photoanodes and counter electrodes in dye-sensitized solar cells and interfacial layers and charge carriers in perovskite solar cells. Ultimately, burdensome tasks and possible directions for advancing MOFs-based nanomaterials are provided for solar cells.

We have designed cell penetrating peptides that target the leucine zipper transcription factors ATF5, CE-BPB and CEBPD and that promote apoptotic death of a wide range of cancer cell types, but not normal cells, in vitro and in vivo. While such peptides have the potential for clinical application, their mechanisms of action are not fully understood. Here, we show that one such peptide, Dpep, compromises glucose uptake and glycolysis in a cell-context-dependent manner (in about 2/3 of cancer lines assessed). These actions are dependent on induction of tumor suppressor TXNIP (thioredoxin interacting protein) mRNA and protein. Knockdown studies show that TXNIP significantly contributes to apoptotic death in those cancer cells in which it is induced by Dpep. The metabolic actions of Dpep on glycolysis led us to explore combinations of Dpep with clinically approved drugs metformin and atovaquone that inhibit oxidative phosphorylation and that are in trials for cancer treatment. Dpep showed additive to synergistic activities in all lines tested. In summary, we find that Dpep induces TXNIP in a cell-context-dependent manner that in turn sup-presses glucose uptake and glycolysis and contributes to apoptotic death of a range of cancer cells.

This study investigates the adoption of ecological innovations and management of occupational health hazards among Nigerian paddy rice farmers in response to field contamination and climate risks. Conducted across four major rice-producing states—Ekiti, Kwara, Edo, and Ogun—the research employed a semi-structured questionnaire developed from a comprehensive literature review and validated through peer review. Data were collected from 192 farmers through face-to-face interviews and guided dialogues, focusing on ecological innovations, vulnerability assessments, satisfaction with implemented methods, occupational health hazards, and perceptions of sustainable rice cultivation. Findings reveal that only 29.69% of farmers have adopted new measures to address contamination and climate risks, while 70.31% have not. Work-related injuries, such as cuts and abrasions, affected 28% of farmers, with minimal participation (3.1%) in safety training and support from agricultural or government agencies (1%). Correlation analysis demonstrated weak relationships among variables such as farmers' education, adoption of ecological innovations, satisfaction with results, and use of personal protective equipment (PPE). Importantly, farmers who adopted ecological innovations expressed significantly higher satisfaction (odds ratio = 11.613), as did those with prior exposure to pesticides and chemicals (odds ratio = 4.084) regarding safety practices. The study emphasizes the critical need for increased awareness, training, and support to promote sustainable farming practices and improve occupational health outcomes among paddy rice farmers in Nigeria.

The prospect of drinking water serving as a conduit for gut bacteria, artificially selected by disinfection strategies and lack of monitoring at the point of use, is concerning. Certain opportunistic pathogens, notably some nontuberculous mycobacteria (NTM), often exceed coliform bacteria levels in drinking water, posing safety risks. NTM and other microbiota resist chlorination and thrive in plumbing systems. When inhaled, opportunistic NTM can infect the lungs of immunocompromised or chronically ill patients, and the elderly, primarily postmenopausal women. When ingested with drinking water, NTM often survive stomach acidity, reach the intestines, migrate to other organs using immune cells as vehicles, potentially colonizing tumor tissue, including in breast cancer. The link between the microbiome and cancer is not new, yet the recognition of intratumoral microbiomes is a recent development. Breast cancer risk rises with age, and NTM infections emerged as a concern among breast cancer patients. In addition to studies hinting at a potential association between chronic NTM infections and lung cancer, NTM have also been detected in breast tumors at levels higher than normal adjacent tissue. Evaluating the risks of continued ingestion of contaminated drinking water is paramount, especially given the ability of various bacteria to migrate from the gut to breast tissue via entero-mammary pathways. This underscores a pressing need to revise water safety monitoring guidelines and delve into hormonal factors, which includes addressing the disproportionate impact of NTM infections and breast cancer on women and examining the potential health risks posed by the cryptic and unchecked microbiota from drinking water.

Background: Despite advances in the treatment of hepatocellular carcinoma (HCC) over the last few decades, treatment opportunities for patients with HCC remain limited. HCC is the most common form of liver cancer, accounting for approximately 90% of all cases worldwide. Moreover, apart from the current pharmacological interventions, hepatic resection and liver transplantation are the mainstay curative approaches for patients with HCC. Methods: This systematic review included phase I, II, III, and IV clinical trials (CTs) and randomized controlled trials (RCTs) on current treatments for patients with HCC in an Asian population (2013–2023). A total of 427 articles were screened, and 184 non-duplicate publications were identified. After screening titles and abstracts, 96 publications were excluded, and another 28 were excluded after full-text screening. The remaining 60 eligible RCTs/CTs were finally included. Results: Sixty clinical trials fulfilled our inclusion criteria and screened 36 drugs as monotherapy or combination therapy for HCC. Most studies used sorafenib alone or in combination with any of the treatment regimens. Lenvatinib or atezolizumab with bevacizumab was used for HCC after initial sorafenib treatment. Eighteen studies compared the efficacy of sorafenib with that of other drugs, including lenvatinib, cabozantinib, tepotinib, tigatuzumab, linifanib, erlotinib, resminostat, brivanib, tislelizumab, selumetinib, and refametinib. Conclusion: This study provides comprehensive insights into effective treatment interventions for HCC in Asian populations. The overall assessment indicated that sorafenib alone or in combination with atezolizumab and bevacizumab has been the first treatment choice in the past decade to achieve better outcomes in patients with HCC in an Asian population

The present article describes the synthesis of an isonicotinate-derived meso-arylporphyrin, that has been fully characterized by spectroscopic methods (including fluorescence spectroscopy), as well as by elemental analysis and by HR-MS. The structure of a n-hexane monosolvate has been determined by single crystal X-ray diffraction analysis. The radical scavenging activity of this new porphyrin against the 2,2-diphenyl-1-picrylhydrazyl (DDPH) radical has been measured. Its antifungal activity against three yeast strains (C. albicans ATCC 90028, C. glabrata ATCC 64677 and C. tropicalis ATCC 64677) has been tested, using the disk diffusion and the microdilution methods. Whereas the measured antioxidant activity was low, the porphyrin showed moderate but encouraging antifungal activity. Finally, a study of its effect on the germination of lentil seeds revealed interesting allelopathic properties.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

Mitochondria are dynamic organelles that can adjust and respond to different stimuli within a cell. This plastic ability allows them to effectively coordinate several cellular functions in cells and becomes particularly relevant in highly complex cells such as neurons. An imbalance in mitochondrial dynamics can disrupt mitochondrial function, leading to abnormal cellular function and ultimately to a range of diseases, including neurodegenerative disorders. Regulation of mRNA transport and local translation inside neurons is crucial for maintaining the proteome of distal mitochondria, which is vital for energy production and synaptic function. A significant portion of the axonal transcriptome is dedicated to mRNAs for mitochondrial proteins, emphasizing the importance of local translation in sustaining mitochondrial function in areas far from the cell body. In neurons, local translation and the regulation of mRNAs encoding mitochondrial-shaping proteins could be essential for synaptic plasticity and neuronal health. The dynamics of these mRNAs, including their transport and local translation, may influence the morphology and function of mitochondria, thereby affecting the overall energy status and responsiveness of synapses. Comprehending the mitochondria-related mRNAs regulation and local translation, as well as its influence on mitochondrial morphology near the synapses will help to better understand neuronal physiology and neurological diseases where mitochondrial dysfunction and impaired synaptic plasticity play a central role.

The chemical investigation of the anti-yeast methanol extract from the stem bark of Terminalia mantaly led to the isolation of seven compounds: 3-O-methyl-4-O-α-rhamnopyranoside ellagic acid (1), 3-O-mehylellagic acid (2), arjungenin or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid (3), arjunglucoside or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid glucopyranoside (4), 2α,3α,24-trihydroxyolean-11,13(18)-dien-28-oïc acid (5), stigmasterol (6), stigmasterol 3-O-β-D-glucopyranoside (7). Their structures were established by means of spectroscopic analysis and comparison with published data. Compounds 1-5 were tested in vitro for activity against three pathogenic yeast isolates, Candida albicans, Candida parapsilosis and Candida krusei. The activity of compounds 1, 2 and 4 were comparable to that of the reference compound fluconazole (MIC values below 32 µg/ml) against the three tested yeast isolates. They were also tested for inhibitory properties against four enzymes of metabolic significance: Glucose-6-Phosphate Deshydrogenase (G6PD), human erythrocyte Carbonic anhydrase I and II (hCA I and hCA II), Glutathione S-transferase (GST). Compound 4 showed highly potent inhibitory property against the four tested enzymes with overall IC₅₀ values below 4 µM and inhibitory constant (Ki) <3 µM.

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) is a promising chemotherapeutic agent because of its selective apoptotic action on cancer cells. However, resistance to TRAIL-induced apoptosis remains a challenge in many cancers. The gintonin-enriched Panax ginseng extract fraction (GEF) has diverse pharmacological benefits. We explored the combined efficacy of GEF and TRAIL in inducing apoptosis in human renal cell carcinoma (RCC) cells. The effect of GEF treatment on viability, clonogenic potential, wound healing, and TRAIL-induced apoptotic signaling of RCC cells was studied in vitro. Our investigation revealed that GEF pre-treatment sensitized RCC cells to TRAIL-induced apoptosis, as evidenced by DNA fragmentation and cell proliferation, colony formation, and migration inhibition. This sensitization was linked to the upregulation of death receptors 4 and 5 and alterations in apoptotic protein expression; notably, decreased expression of Mu-2-related death-inducing gene, a novel anti-apoptotic protein. Our findings underscore the necessity of caspase activation for GEF/TRAIL-induced apoptosis using the pan-caspase inhibitor Z-VAD-FMK. It demonstrates that GEF sensitizes human RCC cells to TRAIL-induced apoptosis by upregulating DR4/5 and modulating apoptotic protein expression. These findings suggest a promising strategy for overcoming TRAIL resistance in cancer therapy and highlight the potential of GEF as a valuable adjunct to TRAIL-based treatments.

Alkaloid-based urea derivatives were produced with high yield through the reaction of anabasine and cytisine with isoxazolylphenylcarbamates in boiling benzene. Their antitumor ac-tivity in combination with the commonly used six anticancer drugs namely cyclophosphane, fluorouracil, etoposide, cysplatine, ribomustine with different mechanisms of action was investi-gated. Based on the quantum chemical calculations data and molecular docking, hypotheses have been put forward to explain their mutual influence when affecting on the С6 rat glioma model cells.

The aim of this study is to characterize the compound extremes of rainfall and temperature in Côte d’Ivoire. For this purpose, we analyzed the outputs of fourteen (14) climate models from the CORDEX-Africa project. Results show an increase (approximately 4.3°C) of the surface temperature and a decrease (5,90 %) of the mean rainfall in the near (2036-2065) and far futures (2071-2100) over Côte d’Ivoire during January-February-March (JFM) period. The analysis of the compound extremes of wet/warm type highlights an increase in the frequency of this climatic hazard in the northern and central parts of the country during January-March (JFM) season in the near and far futures. The dry/warm mode will increase in the central and southern parts of the country during the near future and in the whole country during the far future. These increase in compound extremes could lead to an increase in droughts and natural disasters over the country and could have a negative impact on socio-economic activities, such as transportation and agricultural production. This work could provide decision support for political decision-makers in formulating future public policies for managing agricultural production, food security, and natural disasters.

During the last years there has been a high interest in the development of new purely-organic single-component conductors. Very recently, we have reported a new neutral radical conductor based on the perchlorotriphenylmethyl (PTM) radical moiety linked to a monopyrrolo-tetrathiafulvalene (MPTTF) unit by a -conjugated bridge (1). Interestingly, this system behaves as a semiconductor with high conductivity and small energy gap under high pressure. With the aim of developing a new material with improved conducting properties, we have designed and synthesized the radical dyad 2 which was functionalized with an ethylenedithio (EDT) group in order to improve the intermolecular interactions of the TTF subunits. The physical properties of the new radical dyad 2 were studied in detail in solution to further analyze its electronic structure as well as its potential use as radical conductor in the solid state.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

The anatomy of mature vertebrate hearts is marked by a looped design, which is roughly characterized by two components: (1), s-shaped (sigmoid) routing of the cardiac flow path(s), and (2,) bilaterally asymmetric (chiral) routing of the cardiac flow path(s). The looped heart design is regarded as a phylogenetically conserved feature among vertebrates and is thought to represent a significant determinant of the cardiac pumping function. It evolves during the embryonic period of development by a morphogenetic process called “cardiac looping”. During the past decades, remarkable progress has been made in the uncovering of the genetic, molecular, and biophysical factors contributing to cardiac looping. Thereby, a special focus was directed on the evolution of a bilaterally asymmetric (chiral) heart configuration, which is said to play a central role in the determination of the alignments and separations of the pulmonary and systemic flow paths in the multi-chambered hearts of tetrapods. In contrast to the recent progress made in uncovering of the biological driver of cardiac looping, our present knowledge about the functional consequences of cardiac looping is at an immature state. This article provides an overview and discussion of the currently available information about the looped design of vertebrate hearts and its functional implications.

DSSC devices are among the most widely studied thin-film solar cells because of their cost-effectiveness, low toxicity, and simple fabrication method. However, there is still much scope for replacing current DSSC materials due to their high cost, low volume, and lack of long-term stability. Accordingly, ITO-nanorod films were fabricated by E-beam evaporation using the glancing angle deposition method in this study. Then, the ITO-nanorod was treated by oxygen plasma via a bias-magnetron RF sputtering process to improve the efficiency of DSSC under a varying gas flow rate of 20, 40, 60, 80, and 100 sccm. The FE-SEM investigation of the ITO film structure revealed that the obtained nanorod structures have slightly different diameters. At the same time, an increase in the oxygen flow rate resulted in a rougher film surface structure. In this, the lower sheet resistance was received because of rougher morphology. When comparing the DSSC efficiency test results, we found that at a gas flow rate of 100 sccm, the highest efficiency value showed by 9.5%. On the other hand, the ITO-nanorod without plasma treatment exhibited the lowest efficiency. Hence, plasma technology can be practically applied to improve the efficiency of DSSC devices. This study will be a prototype of a highly advanced solar cell manufacturing method for the solar cell industry.

JAK2 V617F is a somatic mutation associated with myeloproliferative neoplasm (MPN): polycythemia vera (PV), essential thrombocythemia (ET) and primary myelofibrosis (PMF). In MPNs this mutation is associated with the germline GGCC (46/1) haplotype. Most studies consider the association of the JAK2 haplotypeGGCC_46/1 with some MPNs clinical parameters but no one analyzed the association between JAK2 haplotypeGGCC_46/1 and the onset of onco-drug resistance. Thus, we assessed for JAK2 46/1 haplotype correlation with therapy response in JAK2 V617F positive patients. Patients with MPN, selected by the Hematology Laboratory of “V. Fazzi” Hospital (LE), were analyzed with RLFP-PCR assay with rs10974944 SNP. Most of them had PV (63%) or PMF (61%). Among patients that developed onco-drug resistance, 58% had C/G genotype and only 11% had the G/G allele. No correlation between onco-drug resistance and JAK2 haplotype 46/1 variants emerged. Nevertheless, we observed that G/G allele seems to be related to MPNs evolution to myelofibrosis and to the development of onco-drug resistance clinical parameters (p-value= 0.002449; odd ratio of 3.701209). Thus, although other analyses are required, due to the narrow cardinality of sample, our findings suggest how the G/G allele could be useful for MPNs diagnosis and for the prediction of the disease outcome.

A series of D–π–A diketopyrrolopyrrole (DPP)-based small molecules have been designed for organic light-emitting diodes (OLEDs) and organic solar cells (OSCs) applications. Appling the PBE0/6-31G(d,p) method, the ground state geometry and relevant electronic properties were investigated. The first excited singlet state geometry and the absorption and fluorescent spectra were simulated at the TD-PBE0/6-31G(d,p) level. The calculated results reveal that the photophysical properties are affected through the introduction of different end groups. Furthermore, the electronic transitions corresponding to absorption and emission exhibit intramolecular charge transfer feature. It was disclosed that the designed molecules act not only as luminescent for OLEDs, but also donor materials in OSCs. Moreover, they also can be used as potential electron transfer materials using for OLEDs and OSCs.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

Surface passivation, which has been intensively studied recently, is essential for the perovskite solar cells (PSCs), due to the intrinsic defects in perovskite crystal. A series of chemical or physical methods have been published for passivating the defects of perovskite, which effectively suppressed the charge recombination and enhanced the photovoltaic performance. In this study, the n-type semiconductor of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) is dissolved in chlorobenzene (CB) for the surface passivation during the spin-coating process for depositing the two-dimensional (2D) perovskite film. This approach simplifies the fabrication process of 2D PSCs and benefits the film quality. As a result, the defects of perovskite film are effectively passivated by this method. A better perovskite/PCBM heterojunction is generated, exhibiting an increased film coverage and improved film morphology of PCBM. It is found that this technology results in an improved electron transporting performance as well as suppressed charge recombination for electron transport layer. As a result, PSCs based on the one-step formed perovskite/PCBM heterojunctions exhibit the optimized power conversion efficiency of 15.69% which is about 37% higher than that of regular perovskite devices. The device environmental stability is also enhanced due to the quality-improved electron transport layer.

The accurate prediction of heat load profiles with a daily resolution is required for a broad range of applications such as potential studies, design, or predictive operation of heating systems. If the heat demand of a consumer is mainly caused by (production) processes independent of the ambient temperature, existing load profile prediction methods fail. To close this gap, this study develops two ex post machine learning models for the prediction of the heat demand with a daily resolution. The selected input features are commonly available to each consumer connected to public natural gas and electricity grids or operating an energy monitoring system: Ambient temperature, weekday, electricity consumption, and heat consumption of the last seven days directly before the predicted day. The study’s database covers electricity and natural gas consumption load profiles from 82 German consumers over a period of two years. Electricity and heat consumption correlate strongly with individual patterns for many consumers. Both, shallow and deep learning algorithms are evaluated. The highest accuracy is achieved by a Long Short Term Memory (LSTM) model with a median of R² of 0.94. The ex post model architecture makes the model suitable for automated anomaly detection in energy monitoring systems.

Japanese plum tree (Prunus salicina Lindl.) is mainly cultivated in temperate areas of China and some European countries. Certain amounts of wood (from pruning works) are generated every year from this crop of worldwide commercial significance. The main objective of this work was to value this agricultural woody residue, for which the chemical composition of pruning wood extracts from six Japanese plum cultivars was investigated, and the antiproliferative activity of extracts and pure phenolics present in those extracts was measured. For the chemical characterization, total phenolic content and DPPH radical-scavenging assays and HPLC‒DAD/ESI‒MS analyses were performed, the procyanidin (‒)-ent-epicatechin-(2α→O→7,4α→8)-epicatechin (5) and the propelargonidin (+)-epiafzelechin-(2β→O→7,4β→8)-epicatechin (7) being the major components of the wood extracts. Some quantitative differences were found among plum cultivars, and the content of proanthocyanidins ranged from 1.50 (cv. ‘Fortune’) to 4.44 (cv. ‘Showtime’) mg/g of dry wood. Regarding the antitumoral activiy, eight wood extracts and four phenolic compounds were evaluated in MCF-7 cells after 48 h of induction, showing the wood extract from cv. ‘Songold’ and (‒)-annphenone (3) the best antiproliferative activity (IC50: 424 ppm and 405 ppm, respectively).

Solar energy has emerged as a promising alternative to traditional fossil fuels due to its abundant availability and sustainability. Solar cells, the fundamental units of solar energy conversion, have undergone significant advancements in fabrication techniques to enhance their efficiency, durability, and cost-effectiveness. This review aims to provide a comprehensive overview of various methods employed in the preparation of solar cells, including thin-film, crystalline silicon, organic, and perovskite-based technologies. By analyzing recent research developments, challenges, and future prospects, this article sheds light on the evolving landscape of solar cell fabrication, contributing to the ongoing efforts in achieving widespread adoption of solar energy.

The focus of this research is to improve the performance of dye-sensitized solar cells (DSSC) through the adoption of high-quality FTO thin films and incorporation of graphene with DSSC photoanode to enhance its electrical transport. In this research, nanostructured FTO films were first grown with homemade Streaming Process for Electroless and Electrochemical Deposition technology (SPEED) using Tin (II) chloride dihydrate and ammonium fluoride and other chemical formulations. The FTO structural property was measured by X-ray diffraction (XRD); the films’ optical property was determined with transmittance spectra to curve over the wavelength range of 200-1000 nm measured with a spectrophotometer while scanning electron microscope (SEM) was used to determine the morphological properties of the samples. The electrical transport was evaluated by Hall Effect measurements at room temperature with a four-point probe. The FTO samples with the best structural, optical and electrical properties were employed as electrodes and counter electrodes of DSSC along with titanium dioxide. Thus, effect of graphene on the efficiency of DSSC was investigated. It was shown that a graphene-based DSSC showed an efficiency of 7.98% which is slightly higher than that of DSSC prototype without graphene (6.02%). The higher efficiency obtained with graphene can be credited to the ultrahigh surface area and thermal conductivity of graphene which tend to enhance the charge mobility and photovoltaic performance of DSSC. More research is however required to determine the exact amount of graphene that could achieve optimal DSSC performance. Further studies will also offer an adequate clarification for starting point of the better incorporation of graphene in DSSCs.

This paper deals with the problem of determining the optimal capacity of Concentrated Solar Power (CSP) plants, especially in the context of hybrid solar power plants. This work presents an innovative analytical approach to optimize the capacity of concentrated solar plants. The proposed method is based on the use of additional non-dimensional parameters, in particular the design factor and the solar multiple factor. The paper presents a mathematical optimization model that focuses on the capacity of concentrated solar power plants where thermal storage plays a key role in the energy source. The analytical approach provides a more complete understanding of the design process for hybrid power plants. In addition, the use of additional factors and the combination of the proposed method with existing numerical methods allows for a more refined optimization, which allows for a more accurate selection of the capacity for specific geographical conditions. Importantly, the proposed method significantly increases the speed of computation compared to traditional numerical methods. Finally, the authors present the results of the analysis of the proposed system of equations for calculating the levelized cost of electricity (LCOE) for hybrid solar power plants. The nonlinearity of the LCOE on the main calculation parameters is shown.

Type I (IFN-α/β) and Type III (IFN-λ) interferon-inducible myxovirus resistance (Mx) proteins have long been recognized to inhibit a broad spectrum of RNA- and DNA-containing viruses (1-5). Mx proteins are dynamin-family GTPases of size 60-70 kDa (1-3) with different subcellular localization and antiviral activities. In the last 5 years there has been a paradigm shift in our understanding of the structures formed by human and murine Mx proteins in the cytoplasm and nucleus. We now recognize that the major human MxA protein forms structures in the cytoplasm and the major murine Mx1 forms structure in the nucleus which comprise liquid-liquid phase separated (LLPS) biomolecular condensates [membraneless organelles (MLOs)] with a gel-like internal consistency. The second human Mx protein, MxB, which had been previously observed to associate with the cytoplasmic face of nuclear pores, was also recently confirmed to represent cytoplasmic biomolecular condensates. Our overall focus now is to understand the formation, dynamics and antiviral function of biomolecular condensates of different Mx proteins in the cytoplasm and nucleus in cells of different species. We highlight the metastability and rapidly reversible hypotonicity sensing properties of MxA condensates in human cells, especially as applicable to environmental stress inflicted on the oral mucosa.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .

We conducted this systematic review with the objective to understand the efficacy and safety of proton pump inhibitors [PPIs] in the pediatric population. We have used PubMed to identify randomized controlled trials [RCTs] published between 1st June 2010 and 30th June 2023, in patients from birth to 18 years old, with gastroesophageal reflux disease [GERD], who received treatment with any PPI. The literature yielded 76 articles and 13 met inclusion criteria. For infants, PPIs were equal to placebo in reducing GERD symptoms in 4 articles. In 1, the number of GER episodes and esophageal acid exposure were lower in infants who received PPIs and left lateral position, but there was no significant improvement in symptoms. In another publication, the combination of PPIs and feeding modifications [FM] was not more effective than PPIs alone. For children and adolescents, PPIs were effective in improving symptoms and achieving mucosal and histological healing, which was subsequently maintained. To conclude, PPIs are not effective to reduce symptoms related to GERD in infants, but are effective in older children, along with histological remission. Generally, PPIs are well tolerated, but it is important to not forget the possible adverse events [AE], especially if they are used for a long time.

Cholesterol homeostasis is pivotal for cellular function. Acyl-coenzyme A:cholesterol acyltransferase 1 (ACAT1), also abbreviated as SOAT1, is an enzyme catalyzing the storage of excess cholesterol to cholesteryl esters. ACAT1 is an emerging target to treat diverse diseases including atherosclerosis, cancer, and neurodegenerative diseases. F12511 is a high affinity ACAT1 inhibitor. Previously, we developed a stealth liposome-based nanoparticle to encapsulate F12511 to enhance its delivery to the brain and showed its efficacy in treating a mouse model for Alzheimer’s disease (AD). In this study, we introduce F26, a close derivative of F12511 metabolite in rats. F26 was encapsulated in the same DSPE-PEG2000/phosphatidylcholine (PC) liposome-based nanoparticle system. We employed various in vitro and in vivo methodologies to assess F26's efficacy and toxicity compared to F12511. Results demonstrate that F26 is more effective and durable than F12511 in inhibiting ACAT1, in both mouse embryonic fibroblasts (MEFs) and in multiple mouse tissues including the brain tissues, without exhibiting any overt systemic or neurotoxic effects. This study demonstrates the superior pharmacokinetic and safety profile of F26 in wild-type mice, and suggests its therapeutic potential against various neurodegenerative diseases including AD.

Abstract Octreotide is the first synthetic peptide hormone, consisted of eight amino acids, that mimics the activity of somatostatin, a natural hormone in the body. During the past decades, advanced instrumentation and crystallographic software established X-ray Powder Diffraction (XRPD) as a valuable tool for extracting structural information of biological macromolecules. The latter was demonstrated by the successful structural determination of octreotide at a remarkably high d-spacing resolution (1.87 Å) (PDB code: 6vc1). This study focuses on the response of octreotide to different humidity levels and temperatures, with a particular focus on the stability of the polycrystalline sample. XRPD measurements were accomplished employing an Anton Paar MHC-trans humidity-temperature chamber installed within a laboratory X’Pert Pro diffractometer (Malvern Panalytical). The chamber is employed to control and maintain precise humidity and temperature levels of samples during XRPD data collection. Pawley analysis of the collected data sets revealed that the octreotide polycrystalline sample is remarkably stable and no structural transitions were observed. The compound retains its orthorhombic symmetry (space group: P212121, a = 18.57744(4) Å, b = 30.17338(6) Å, c = 39.70590(9) Å, d~ 2.35 Å). However, a characteristic structural evolution in terms of lattice parameters and volume of the unit-cell is reported mainly upon controlled relative humidity variation. In addition, an improvement of signal-to-noise ratio in the XRPD data under a cycle of dehydration/rehydration is reported. These results underline the importance of considering the impact of environmental factors, as humidity and temperature, in the context of structure-based drug design, thereby contributing to the development of more effective and stable pharmaceutical products.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

In this study, the microbial strain was isolated from the humus soil to ferment Sophora flavescens and Eleutherococcus sessiliflorus extracts. The isolated microbial was identified as Bacillus genus by 16S rRNA sequence analysis. The fermented plant extracts exhibited the antifungal effects against four types of the plant pathogens such as P. carotorum, B. cinerea, C. fructicola Sau-3, and C. gloeosporioides according to incubation time. Especially, the fermented plant extracts showed the most active activities for Colletotrichum genus to inhibit mycelium growth. Metabolite changes in fermented S. flavescens and E. sessiliflorus extracts were confirmed through LC-Q-TOF/MS. Flavonoid and peptide derivatives were improved in fermented S. flavescens and E. sessiliflorus extracts compared to their unfermented one, respectively. This study suggested that the isolated Bacillus microbial fermentation could be a valuable tool in improving the bioactivity of S. flavescens and E. sessiliflorus extracts to have potential with more environmentally-friendly antifungal agents.

One of the important research directions in the field of photovoltaics is integration with construction. The integration of solar cell systems with a building can reduce installation costs and help optimize the used space. One of the interesting types of cells is dye-sensitized solar cells. In addition to their interesting properties, they also have aesthetic value. In the classic arrangement, they are constructed using glass with a transparent conductive layer (TCL). This article describes replacing a classic glass counter electrode with an electrode based on a ceramic tile and nickel foil. This solution makes it possible to expand their construction applications. The advantage of this solution is full integration with construction while simultaneously generating electricity. A dye-sensitized solar cell was built layer-by-layer on ceramic tile and nickel foil. An atomization method was used to deposit fluorine-doped tin oxide, and then a screen printing method was used to deposit a platinum layer. The electrical parameters of the manufactured DSSCs with and without a counter electrode tile were characterized by measuring their current-voltage characteristics under standard AM 1.5 radiation. A dye-sensitized solar cell integrated with ceramic tiles and nickel foil was produced and displayed an efficiency of over 4%.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.

It is well known that the major constrain to the efficiency of photovoltaic (PV) devices comes from the generation of unused heat. In this context, thermoelectric generators have been proposed as a viable heat recovery solution, leading to an increase of the overall efficiency. Within this kind of hybrid solutions, the PV and TEG parts can be either electrically separated or connected in the same circuit. In the second case, the presence of the TEG in series to the PV cell can lead to electrical losses. In this work we analyze the effect of various parameters on the output power of electrically hybridized HTEPV systems by means of both electrical measurements and simulations. The results reveal that while electrical lossless condition exists (as also reported in previous work) it not always corresponds to significant power gains respect with the sole PV case. In addition, the strong temperature sensitivity of the lossless condition makes the electrical hybridization hardly practically implementable. This sensitivity in the framework of an actual application scenario, where the solar radiation is variable over time, would make the system working often in a suboptimal regime. The present study gives a new understanding on the actual applicability of electrically hybridized HTEPV devices.

For centuries, humans have relied on natural products to prevent and treat numerous health issues. However, biologically active compounds from natural sources, such as polyphenols, face significant challenges, including low solubility, rapid metabolism, and instability, which hinder their effectiveness. Advances in science and nanotechnology have provided solutions to overcoming these problems through the use of porous silica materials. These materials possess unique properties, such as a high specific surface area, adjustable particle and pore sizes, and a surface that can be easily and selectively modified. In this review, we summarize and discuss findings on how the pore and particle size, structure, and surface modification of silica materials influence the preparation of efficient delivery systems for biologically active polyphenols from natural sources. The available data demonstrate how parameters such as adsorption capacity, release and antioxidant properties, bioavailability, solubility, stability, etc. of the studied delivery systems could be affected by the structural and chemical characteristics of the porous silica carriers.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

Every individual at some point encounters the progressive biological process of aging which is considered one of the major risk factors for common diseases. The main drivers of aging are oxi-dative stress, senescence, and Reactive oxygen species (ROS). The renin-angiotensin-aldosterone system (RAAS) includes several systematic processes for the regulation of blood pressure which is caused by an imbalance of electrolytes. During activation of RAAS, binding of angiotensin II (ANG II) to angiotensin II type I receptor (AGTR1) activates intracellular NADPH oxidase to generate superoxide anions and promote uncoupling of endothelial NO synthase, which in turn decreases NO availability and increases ROS production. Promoting oxidative stress and DNA damage mediated by ANG II is tightly regulated. Individuals with sodium deficiency-associated diseases such as Gitelman syndrome (GS) and Bartter syndrome (BS) show down-regulation of inflammation-related processes and have reduced oxidative stress and ROS. Additionally, the histone deacetylase-Sirtuin-1(SIRT1) has a significant impact on the aging process with reduced activity with age. However, GS/BS patients generally sustain higher levels of SIRT1 activity than aged-matched healthy individuals. In this review, we highlight the importance of the hallmarks of aging, inflammation, and the RAAS system in GS/BS patients and how this might impact healthy aging. We further propose fu-ture research directions for studying the etiology of GS/BS at the molecular level using pa-tient-derived renal stem cells and induced pluripotent stem cells.

In the frame of our diversity-oriented research on multitarget small molecule anticancer agents, utilizing convergent synthetic sequences terminated by Sonogashira coupling reactions, a preliminary selection of representative alkyne-tethered vindoline hybrids was synthesized. The novel hybrids with additional pharmacophoric fragments of well-documented anticancer agents, including FDA-approved tyrosine-kinase inhibitors (imatinib and erlotinib) or ferrocene or chalcone units, were evaluated for their antiproliferative activity on malignant cell lines MDA-MB-231 (triple negative breast cancer), A2780 (ovarian cancer), HeLa (human cervical cancer) and SH-SY5Y (neuroblastoma) as well as human embryonal lung fibroblast MRC-5 served as reference non-malignant cell line for the assessment of the therapeutic window of the tested hybrids. The biological assays identified a trimethoxyphenyl-containing chalcone-vindoline hybrid (36) as a promising lead compound exhibiting submicromolar activity on A2780 cells with a marked therapeutic window. These results suggest that ovarian cancer might be considered as a prioritized target of treatment with 36.

Uterine leiomyosarcoma (LMS) is a rare and aggressive form of uterine cancer, with a poor prognosis and high number of uterine cancer-related deaths. Chimeric Antigen Receptor (CAR) T-cell therapy is an immunotherapy approach to antigen specific of cancer cell, thereby enhancing the immune system's ability to target and destroy cancer cells. This study aims to investigate the potential of targeting differentially expressed genes (DEGs) as a novel therapeutic strategy using CAR T-cell technology in LMS. Genome datasets were obtained from NCBI-GEO database, Of the five datasets, genes that experienced significant overexpression in at least three datasets were categorized as DEGs, and DEGs were evaluated for protein localization, Gene Ontology, bioactivity, interaction, and overexpression. The results identified 25 DEGs, with ten of them expressed on the plasma membrane; four of them—HMMR, KIF20A, PRC1, and ZWINT—were part of the main protein network derived from the 25 DEGs. The dominant bioactivity of these PMGs involves influencing the cell cycle, particularly processes related to chromosome segregation. In conclusion, HMMR, KIF20A, PRC1, and ZWINT are high-potential DEGs as candidates for tumor-associated antigen CAR T-cell therapy. Further research, both in vitro and in vivo, is needed to enhance the validity of these findings.

This study provides a comprehensive analysis of the conformational dynamics of pseudo-endocannabinoid receptors (p-CBRs) CB₁ and CB₂ in response to ligand binding. The ligands studied include N-arachidonoyl dopamine (NADA), Cannabidiol (CBD), known agonists (FUB-MDMB and E3R), and inverse agonists (Taranabant and AM630). Using homology models based on crystal structures (PDB ID: 5U09 for CB₁ and 5ZTY for CB₂), molecular docking, and molecular dynamics (MD) simulations, the research validates the structural integrity and dynamic behaviours of these pseudo-receptors. Induced-fit docking revealed NADA as having the highest binding affinity for both receptors, with docking scores of −13.92 kcal/mol for CB₁ and −13.32 kcal/mol for CB₂, facilitated by key hydrogen bond interactions. MD simulations over 250 ns at ~298 K showed successful equilibration, indicating the most stable interaction for NADA, thereby further validating the models. CB₁ and CB₂ exhibited distinct conformational responses to ligands, with Cα RMSD and Cα RMSF analyses suggesting a more rigid binding pocket for CB₁ and a flexible binding pocket for CB₂. These findings highlight the significance of receptor behaviour and dynamics in the development of cannabinoid-based therapeutics, supporting the potential of CBD and NADA as modulators for CB₁ and CB₂, respectively.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

Indole is a versatile pharmacophore widely distributed in bioactive natural products. This privileged scaffold has been found in a variety of molecules isolated from marine organisms such as algae and sponges. Among these, indole alkaloids represent one of the biggest, most promising family of compounds, having shown a wide range of pharmacological properties, including anti-inflammatory, antiviral and anticancer activities. The aim of this review is to show the current scenario of marine indole alkaloid derivatives, covering not only the most common chemical structures, but also new synthetic routes developed during the last years as well as promising therapeutic applications.

Hydrogen gas (H2) has attracted attention as a next-generation clean energy source. Its efficient and safe preparation and utilization are crucial in both industry and organic chemistry. In this study, a Pt/CB-catalyzed MW-mediated continuous-flow hydrogenation reaction was developed using methylcyclohexane (MCH) as the reducing agent (hydrogen carrier). Alkynes, alkenes, nitro groups, benzyl esters, and aromatic chlorides were chemoselectively hydrogenated using Pt/CB under MW-assisted continuous-flow conditions. This methodology represents a safe and energy-efficient hydrogenation process, as it eliminates the need for an external hydrogen gas supply or heating jackets as a heat medium. Further application of MW-mediated continuous-flow hydrogenation reactions is a viable method for the efficient generation and utilization of sustainable energy.

Given the accelerating scientific, clinical and consumer interest in highly-prevalent functional gastrointestinal disorders, appropriate therapeutic strategies are needed to address the many aspects of digestive dysfunction. Accumulating evidence for the crucifer-derived bioactive molecule, sulforaphane in upstream cellular defence mechanisms highlights its potential as a therapeutic candidate in targeting functional gastrointestinal conditions together with systemic disorders. This article catalogues the evolution of and rationale for a hypothesis that utilises multifunctional sulforaphane as the initial step in restoring the ecology of the gut ecosystem; it does this primarily by targeting the functions of intestinal epithelial cells. A growing body of work has identified the colonocyte as the driver of dysbiosis, so that targeting gut epithelial function could provide an alternative to targeting the microbes themselves for remediation of microbial dysbiosis. The hypothesis discussed herein has evolved over several years and is supported by case studies showing the application of sulforaphane in gastrointestinal disorders, related food intolerance and several systemic conditions. To our knowledge, this is the first time the effects of sulforaphane have been reported in a clinical environment where several of its key properties within the gut ecosystem appear to be related to its nutrigenomic effects on gene expression.

Xanthone derivatives, a class of natural compounds abundantly found in plants such as mangosteen (Garcinia mangostana) and certain herbs, have garnered substantial interest due to their diverse pharmacological properties, including antioxidant, anti-inflammatory, and anti-cancer activities. Recent investigations have unveiled their potential as modulators of enzymatic activity, prompting exploration into their effects on hyaluronidase-mediated HA degradation, and their effects in topical treatment of telangiectasia and rosacea. Telangiectasia and rosacea are common dermatological conditions characterized by chronic skin inflammation, vascular abnormalities, and visible blood vessels, resulting in significant cosmetic concerns and impaired quality of life for affected individuals. This review aims to provide a comprehensive overview of the current understanding regarding the interplay between mechanisms of action by which xanthone derivatives exert their therapeutic effects, including the inhibition of pro-inflammatory cytokines, modulation of oxidative stress pathways, and regulation of vascular endothelial growth factors. Furthermore, we will discuss the implications of harnessing xanthone derivatives as therapeutic agents for mitigating vascular dysfunction and its associated pathologies, thereby offering insights into future research directions and therapeutic strategies in the field of vascular biology.

The dynamic evolution and variation of electrical loads is now a priority for optimum management and, above all, forecasting. Indeed, these dynamic load variations require computer tools able to implement optimal load forecasting models. Scientific research into automated models for forecasting electrical loads therefore represents a challenge for scientific researchers. Several research studies have therefore been carried out. These include machine learning approaches such as: LSTM (Long Short-Term Memory), Support Vector Machine (SVM) and others. This article proposes a comparison study between a hybrid model based on the wavelet transform coupled with the adaboost method, and LSTM, for forecasting electricity consumption loads. Python 3.10 was used for the studies. The first results obtained consisted in the study of electricity load forecasts over four (04) data sets of the year (January, April, August and December). These results are very satisfactory, showing a good correlation between the real results of the electrical load consumption data, and the results of the implemented model. The electrical load consumption data are collected from a renewable energy production source: photovoltaic solar energy. The model test results (R2) obtained range from 0.919 to 0.958. These results are representative of real data and reflect the model's performance. The second set of results concerns a comparative study between the methods used by Y. Xie et al (CNN, MLP, LSTM-AM and LSTM-AM-MLP), and our approach. The prediction results obtained between the approaches show a prediction gap ranging from 0.15 to 0.78 for RMSE and 0.83 for MAPE. These results show significant differences between the methods. The minimization of errors by our model, therefore, reflects the model's performance in terms of accuracy, which is necessary for the optimal management of consumer electricity load forecasts in order to ensure balance between supply and demand.

The influences of doped hole transporting layer (HTL) on the performances of perovskite solar cells were studied. The influences of electrostatic and surface roughness effect by solvent additive doping were compared. The electrostatic effect of solvent additive doping was compared by addition of 1,8-diiodooctane and 1,8-dichlorooctane to the HTL layer. The surface roughness effect of solvent additive doping was examined using atomic force microscopy. The perovskite crystallinity by doping HTL was studied by X-ray diffraction. The conductivity of HTL was measured using four probe methods and was higher for doped devices. Enhanced conductivity of PEDOT:PSS film was also proved using fluorescence emission quenching. Long-term stability of the device was enhanced by doping HTL. The device with solvent additive exhibited much enhanced stability, retained over 80% of the initial PCE for 400 hours, while PCE of the device without solvent additive decreased to less than 80% after 200 hours. A very weak power microwave treatment was used for post-annealing of the fully fabricated devices. Post-annealing enhanced the lifetime of the device. Comparing different size of cells, the device lifetime was decreased as the cell area increased and as the size of the cell increased, the extent of lifetime enhancement by doping was increased.

Zinc oxide (ZnO) has been widely studied over the last decade for its remarkable properties in optoelectronic and photovoltaic devices because of its high electron mobility and excitonic properties, probably the broadest range of nanostructured forms, and their ease and low cost of synthesis by a wide variety of methods. The volume of recent work on ZnO nanostructures and their devices can potentially overshadow significant developments in the field. Therefore, there is a need for a concise description of the most recent advances in the field. In this review, we focus on the effect of ZnO nanostructure morphologies on the performance of ZnO-based solar cells sensitized using methylammonium lead iodide perovskite. We present an exhaustive discussion of the synthesis routes for different ZnO nanostructure morphologies, ways to control the morphology, and the impact of morphology on the photo-conversion efficiency of a given PSC.

We report on the effects of the film morphology on the fluorescence spectra for a thin film including a quinoxaline-based co-polymer (TQ1) and a fullerene derivative (PC₇₀BM). The ratio between the polymer and the fullerene derivative, as well as the processing solvent were varied. Beside the main emission peak at 700 nm in the fluorescence spectra of thin films of this phase-separated blend, a broad emission band is observed with a maximum at 520 - 550 nm. The intensity of this emission band decreases with an increasing degree of mixing in the film and becomes most prominent in thicker films, films with high PC₇₀BM content, and films that were spin-coated from solvents with lower PC₇₀BM solubility. We assign this emission band to aggregated PC₇₀BM.

Hybrid metal-halide perovskites have emerged as leading class of semiconductors for photovoltaic devices with remarkable light harvesting efficiencies. The formation of methylammonium lead iodide (CH₃NH₃PbI₃) perovskite into mesoporous titania (TiO₂) scaffold by a sequential deposition technique is known to offer better control over the perovskite morphology. The growth reactions at the mesoporous TiO₂ film depend on reactants concentration in the host matrix and the reaction activation energy. Here, we are characterizing formation of CH₃NH₃PbI₃ perovskite in mimic solar cell photoelectrodes utilizing the developed NanoPlasmonic Sensing (NPS) approach. Based on dielectric changes at the TiO₂ mesoporous film interface, the technique provides time-resolved spectral shifts of the localized surface plasmon resonance that varies widely depending on the different operating temperatures and methylammonium iodide (CH₃NH₃I) concentrations. Analytical studies included Ellipsometry, Scanning Electron Microscopy, and X-ray diffraction. The results show that perovskite conversion can be obtained at lower CH₃NH₃I concentrations if reaction activation energy is lowered. A significant finding is that the NPS response at 350 nm mesoporous TiO₂ can widely change from red shifts to blue shifts depending on extent of conversion and morphology of perovskite formed at given reaction conditions.

The critical role of global electron density transfer (GEDT) in increasing the reaction rate of polar organic reactions has been studied within the framework of Molecular Electron Density Theory (MEDT). To this end, the series of the polar Diels-Alder (P-DA) reactions of cyclopentadiene with cyanoethylene derivatives, for which experimental kinetic data are available, have been chosen. A complete linear correlation between the computed activation Gibbs free energies and the GEDT taking place at the polar transition state structures (TSs) is found; the higher the GEDT at the TS, the lower the activation Gibbs free energy. An interacting quantum atoms (IQA) energy partitioning analysis allows establishing a complete linear correlation between the electronic stabilization of the electrophilic ethylene frameworks and the GEDT taking place at the polar TSs. This finding supports Parr’s proposal for the definition of the electrophilicity  index (J. Am. Chem. Soc., 1999, 121, 1922). The present MEDT study allows establishing the critical role of the GEDT in the acceleration of polar reactions, since the electronic stabilization of the electrophilic framework with the electron density gain is greater than the destabilization of the nucleophilic one, making a net favorable electronic contribution to the decrease of the activation energy.

Vertical III-V semiconductor nanowires have shown promising absorption of light for solar cell and photodetector applications. The absorption properties can be tuned through the choice of III-V materials and geometry of the nanowires. Here, we review recent progress in the design of the absorption properties of both individual nanowires and nanowire arrays. Future directions for the research field are proposed.

Ecological ternary cements (ECP) were perpared with powders of phosphogypsum (PG), fly ash (FA) and portland cement (PC). The evolution mechanism of the hydration product structure was characterized through macro and micro experiments.The thermodynamic characteristics of solid phase, solid solution phase and aqueous solution in process of hydration about phosphogypsum-fly ash-cement ternary cementitious system were studied based on the Gibbs-free-energy C-S-H thermodynamic model and GEM-Selektor software, and compared with experimental results. The results show that in the hydration reaction the thermodynamic interaction between mineral single-phase and hydration products plays an important role in the spatio-temporal distribution of ions in the cementitious system. The values of CaO、SiO2Hand H2Ohyd gradually increased with the increase of Ca/Si ratio, while the values of CaOext and H2OOH showed a positive proportional relationship, and the values of SiO2H and SiO2 showed an inverse proportional relationship. GEM-Selektor is accurate in the simulation calculation of the total amount of AFt and AFm mineral phases which quantitatively analysis the correlation between C-S-H gels formation and C3S with complex decomposition ion groups.

Proper blood-brain barrier (BBB) function is essential to maintain homeostasis keeping the central nervous system healthy. Disruption of the BBB has been described in nearly all neurological disease and injury contexts. Given the various physical and metabolic roles of the BBB and gliovascular unit (GVU), dysfunction should be assessed across multiple levels to pinpoint the exact nature of the impairment. Here we describe imaging techniques for evaluating various aspects of BBB and GVU integrity and function, tailored for use in mouse models with protocols for quantitative image analysis. These imaging techniques complement classical dye tracer experiments and reveal underlying molecular causes of BBB dysfunction.

Certain species of Mucorales have been identified as causative agents of mucormycosis, a rare yet often lethal fungal infection. Notably, these fungi exhibit intrinsic resistance to common azole drugs, which target lipids. Given the pivotal role of lipids in drug resistance and their contribution to the innate resistance to azoles, this study provides a comprehensive overview of key lipid classes, including sphingolipids (SLs), glycerophospholipids(GPLs), and sterols, in Rhizopus delemar 99-880, a well-characterized reference strain among Mucorales. Through high-throughput analysis involving the identification and quantification of intermediates, we have elucidated the biosynthetic pathways of SLs, PGLs, and sterols. Notably, the acidic SLs were not found probably because the acidic branch of the SL biosynthesis pathway terminates at α-hydroxy phytoceramides as evident by their high abundance. Intermediates in the neutral SL pathway incorporated higher levels of 16:0 fatty acid compared to other pathogenic fungi. A strikingly high phosphatidylethanolamine (PE)/phosphatidylcholine (PC) ratio was observed among GPLs. Ergosterol remains the major sterol, similar to other fungi, and our analysis confirms the existence of alternate ergosterol biosynthesis pathways. The total lipidomic profile of R. delemar 99-880 offers insights into its lipid metabolism and potential implications for studying pathogenesis and drug resistance mechanisms.

Passivating the grain boundaries is completely very crucial in the enhancement of the performance of halide perovskite solar cells (PSCs). Here, a novel organolead halide perovskite (CH₃NH₃PbI₃) was synthesized using solution processes-based method to sensitize 1D titanium dioxide (TiO₂) and reduced graphene oxide (RGO) nanoparticles for all-solid-state halide perovskite solar cells. TiO₂ and RGO were synthesized via sol-gel and Hummers’ methods, respectively, and incorporated at the electron transport layer (ETL) in planar PSCs. Additionally, MnO₂ was prepared by chemical method, and used to enhance graphite counter electrode. ITO/RGO/TiO₂/CH₃NH₃PbI₃/Gr and ITO/RGO/TiO₂/CH₃NH₃PbI₃/Gr-MnO₂ planar PSCs were fabricated via spin coating method. ITO/RGO/TiO₂/CH₃NH₃PbI₃/Gr-MnO₂ film achieved a power conversion efficiency (PCE) of 10.79%, short circuit current (Jsc) of 19.0 mAcm^-2 and fill factor (FF) of 51.53% compared to PCE of 8.64%, Jsc of 16.25 mAcm^-2 and FF of 47.48% achieved for ITO/RGO/TiO₂/CH₃NH₃PbI₃/Gr film. The enhancement value of 22.85% was achieved from J-V curves after exposing the ITO/RGO/TiO₂/CH₃NH₃PbI₃/Gr and ITO/RGO/TiO₂/CH₃NH₃PbI₃/Gr-MnO₂ films to Keithley 2400 sourcemeter (Keithley Instrument Inc.) under AM 1.5G (100 mWcm^-2) (Newport) solar illumination in order to test their photovoltaic performance. This study shows that MnO₂ nanoparticle has a proven capability to improve the photovoltaic performance of PSCs.

A sustainable, scalable source of energy‐dense chemical fuel is urgently needed to ensure the security of our energy supply for future generations. Solar energy is the only renewable energy source of sufficient scale to replace fossil fuels and meet rising environmental demand. Hydrogen is expected to play a key role as an energy carrier in future energy systems of the world. As fossil fuel supplies become scarcer and environmental concerns increase, hydrogen is likely to become an increasingly important chemical energy carrier and eventually may become the principal chemical energy carrier. When most of the world’s energy sources become non-fossil based, hydrogen and electricity are expected to be the two dominant energy carriers for the provision of end-use services. Photocatalytic hydrogen evolution from water by solar energy over semiconductors offers a promising way for clean and renewable production of hydrogen. The TiO2-based materials have received considerable attention in recent years due to their extensive application in photocatalysis for hydrogen evolution. Though TiO2 is the most widely investigated photocatalyst for hydrogen evolution, it still provides low photocatalytic activity due to the wide bandgap that results in photocatalytic activity only under ultraviolet (UV) irradiation. Modification of TiO2 photocatalysts with several transition metals has been extensively studied to extend the absorbance capacity of TiO2 into the visible range. The effect of different photocatalytic deposition and reaction parameters also play major roles in enhancing the photostability of photoanode and increasing the hydrogen gas output, respectively.

The solar cell industry is a part of the green energy sector, and effectively combining the patents of various manufacturers within the supply chain to collectively create sustainable patent market value is of paramount importance. This study aimed to establish a business strategy framework for Project-based licensing through the analysis of solar cell patents and the integration of supply chain manufacturers' patents, with the goal of collectively creating market value for patents sustainably. The research methodology included literature analysis and focus group discussions. Initially, the study analyzed solar cell industry patents from the past decade using the WIPS Global Patent database to identify projects with the highest patent count. Subsequently, through the use of focus group discussions, the feasibility of a patent pool strategy within the supply chain was explored. Finally, a strategy framework was proposed for Project-based patent pool licensing, focusing on the top 15 projects with the highest count of 5,579 patents. The results indicated that adopting this strategy framework for supply chain manufacturer patents can result in higher commercial patent value.

This paper focuses on the impact of defects density and carrier capture cross-section area in the electron transport material (ETM), hole transport material (HTM), and absorber layers on the performance of perovskite solar cells and quantum efficiency (QE). Furthermore, the impact of defects density at the interface between ETM/absorber and absorber/HTM is also studied. SCAPS-1D software is used in the current study in determining solar cell performance. The proposed perovskite solar cell structure is a planar FTO/TiO2/ CH3NH3PbI3/ Cu2O. The results indicated that increasing the defect density in the absorber layer significantly affects cell performance, while in ETM and HTM layers, the cell parameters remain unaffected. It is also found that the defect capture cross-section has a similar behavior to the defect density in the main layers (ETM, absorber, and HTM). In addition, it is observed that by increasing the defects density in the ETM/absorber and absorber/HTM interfaces layer, the cell parameters FF, Jsc, and PCE have been slightly decreased, with no effect on Voc. Moreover, it is also noted that the quantum efficiency QE is sharply reduced. Finally, this paper introduced the correlation between the defect density and the capture cross-section, which is the first attempt to find such a relationship in perovskite solar cells to the knowledge of the authors.

The growing interest in benchtop NMR systems is visible in a vast number of applications in science and industry. Low-field nuclear magnetic resonance (LF-NMR) became an instant in technologies that productions are dependent on the reliable structure identification, grade and purity control, chemical process inspection or reaction monitoring. Beyond the benefits of being cost-, space-, maintenance- and user friendly, insufficient sensitivity and low signal resolution are the main drawbacks, due to which the low-field NMR (LF-NMR) in the fields of organic chemistry and synthesis remains limited to solely academic teaching purposes. Herein, we discuss the possibilities of LF-NMR for the needs of organic chemistry and synthesis on a set of compounds 1-4 achieved as the products of student’s laboratory course and organic derivatives 5-8 that are from our research interests. Chemical structure determination of all compounds 1-8 presented herein was performed using the benchtop-type NMR instrument operating at 60 MHz (Pulsar Oxford Ltd.). Structure of novel compounds 5-7 prepared under the aims of our research was characterized by combined 1H/19LF-NMR and compared with an appropriate high-field NMR data from Bruker Ascend Instrument (400 MHz). Finally, possibilities of the low-field NMR as an analytical tool for the research purposes in the fields of organic chemistry and synthesis are documented on a set of 1H and 2D 1H-1H COSY for azomethine 8.

New furan, thiophene and triazole oximes were synthesized through several-step reaction paths to investigate their potential for development of central nervous systems (CNS)-active and cholinesterase-targeted therapeutics in organophosphorus compound (OP) poisonings. Acute OP poisoning is still a challenge in treating patients despite the development of a large number of oxime compounds that should have the capacity to reactivate acetylcholinesterase (AChE) and butyrylcholinesterase (BChE). The activity of these two enzymes, crucial for neurotransmission, are blocked by the OP, which has the consequence of disturbing normal cholinergic nerve signal transduction in the peripheral and CNS, leading to cholinergic crisis. Oximes in use have one or two pyridinium rings and cross the brain–blood barrier poorly due to the quaternary nitrogen. Following our recent study on 2-thienostilbene oximes, in this paper we described the synthesis of 63 heterostilbene derivatives out of which 26 oximes were tested as inhibitors and reactivators of AChE and BChE inhibited by OP nerve agents – sarin and cyclosarin. While the majority of oximes were potent inhibitors of both enzymes in micromolar range, we identified several oximes as BChE or AChE selective inhibitors with a potential for drug development. Moreover, even oximes were poor reactivators of AChE, four heterocyclic derivatives reactivated the cyclosarin-inhibited BChE up to 70%, and cis,trans-5 [2-((Z)-2-(5-((E)-(hydroxyimino)methyl)thiophen-2-yl)vinyl)benzonitrile] had comparable reactivation efficacy to the standard oxime HI-6. In silico analysis and molecular docking studies connected the kinetic data to the structural features of these oximes, and confirmed their productive interactions with the active site of the cyclosarin-inhibited BChE. Based on inhibition and reactivation and their ADMET properties regarding lipophilicity, CNS activity, and hepatotoxicity, these compounds could be considered for further development of CNS-active reactivators in OP poisoning as well as cholinesterase-targeted therapeutics in neurodegenerative diseases like Alzheimer’s and Parkinson’s.

The reaction of berberine derivatives containing at O-9 position N,N-disubstituted acetamide fragments with sodium borohydride in methanol at 0 °C leads to a mild reduction of the "C" cycle with the formation of corresponding tetrahydroberberine derivatives with moderate to good yields.

The dielectric constant (ε) reflects the ability of a material to align and orient electrical dipoles within its structure in response to an externally applied electric field; the greater the polarizability of molecules, the greater the value of dielectric constant. In this study a data set of 86 polymers was investigated to develop a structure-property quantitative relations (QSPR) model to predict the dielectric constant in polymers. An initial set of 1273 descriptors was used to select a best set of descriptors and to construct two machine learning models with Gradient Boosting Regressor (GB_A and GB_B). The best performing model (GB_A) with 8 descriptors, exhibited a performance of (R2train) = 0.938 and (R2test) = 0.802. The models were internally validated by 5 folds cross-validation, demonstrating robustness. Additionally, using the Accumulative Local Effect (ALE) technique, we analyzed the relationship between the 8 descriptors involved and the impact of these descriptors to dielectric constant of polymers.

Traditional silicon binary circuits continue to face challenges such as high leakage power dissipation and large area of interconnections. Multiple-Valued Logic (MVL) and nano-devices are two feasible solutions to overcome these problems. In this paper, we present a novel method to design ternary logic circuits based on Carbon Nanotube Field Effect Transistors (CNFETs). The proposed designs use the unique properties of CNFETs, e.g., adjusting the Carbon Nanotube (CNT) diameters to have the desired threshold voltage and have the same mobility of P-FET and N-FET transistors. Each of our designed logic circuits implements a logic function and its complementary via a control signal. Also, these circuits have a high impedance state which saves power while the circuits are not in use. We show a more detailed application of our approach by designing a two-digit adder-subtractor circuit. We simulate the proposed ternary circuits using HSPICE via standard 32nm CNFET technology. The simulation results indicate the correct operation of the designs under different process, voltage and temperature (PVT) variations. Moreover, we designed a two-digit adder/subtractor and a power efficient ternary logic ALU based on the proposed gates. Simulation results show that the two-digit adder/subtractor using our proposed gates has 12X and 5X lower power consumption and PDP (power delay product) respectively, compared to previous designs.