The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

We consider an $N$ fermion system at low temperature $T$ in which we encounter special particle number values $N_m$ exhibiting special traits. These values arise in focusing attention upon the degree of mixture (DM) of the pertinent quantum states. Given the coupling constant of the Hamiltonian, the DMs stay constant for all $N$-values, but experience sudden jumps at the $N_m$. For a quantum state described by the matrix $\rho$, its purity is expressed by $Tr \rho^2$ and then the degree of mixture is given by $1 - Tr \rho^2$, a quantity that coincides with the entropy $S_q$ for $q=2$. Thus, Tsallis entropy of index two faithfully represents the degree of mixing of a state, that is, it measures the extent to which the state departs from maximal purity . Macroscopic manifestations of the degree of mixing can be observed through various physical quantities. Our present study is closely related to properties of many-fermion systemsn that are usually manipulated at zero temperature. Here we wish to study the subject at finite temperature. Gibbs' ensemble is appealed to. Some interesting insights are thereby gained.

Autosomal dominant polycystic kidney disease (ADPKD) is an inherited disorder characterized by renal tubular cystic dilatations. The cysts can develop anywhere along the nephron and over time the cystic dilatation lead to kidney enlargement. On the other hand, the cysts begin to reduce the number of functional nephrons as a consequence of cystic expansion that further contributes to the decline in renal function over the years. The pressure exerted by the dilated cysts lead to compensatory mechanisms that further contribute to the decline in renal function. These structural changes are responsible of glomerular hyperfiltration states, albuminuria, proteinuria, and haematuria. However, the presentation of ADPKD varies in children from a completely asymptomatic child with incidental ultrasound detection of cysts to a rapidly progressive disease. There have been reports of early onset of ADPKD in children younger than 2 years that showed a more rapid decline in renal function. ADPKD is caused by mutation in PKD1 and PKD2 genes. Today, the PKD1 gene mutation seems to account for up to 85% of the cases worldwide, and it is associated with worse renal outcomes. Individuals with PKD2 gene mutation seem to present a milder form of the disease, with a more delayed onset of end stage kidney disease. The cardinal sign of ADPKD is the presence of renal cysts during renal ultrasound. The current guidelines provide the clinicians the recommendations for genetic testing in children with a positive family history. Given that the vast majority of children with ADPKD present with normal or supra normal kidney function we explored the glomerular filtration rates dynamics and the renal ultrasound adjusted percentiles. 14 out of 16 patients had kidney percentile over 90%. The gene mutations were equally distributed among our cohort. In addition, we compared the modified Schwartz formula to the quadratic equation after adjusting the serum creatinine measurements. It seems that even though children with ADPKD have enlarged kidneys, the renal function is more likely normal or near normal when the quadratic estimation of glomerular filtration rate is used (qGFR tended to be lower, 111.95 ± 12.43 ml/min/1.73m2 compared to Schwartz eGFR 126.28 ± 33.07ml/min/1.73m2, p=0.14). Also, when the quadratic equation was employed, not even a patient reached the glomerular hyperfiltration thresholds. The quadratic formula showed that glomerular filtration rates are linear or slightly decreasing after 1-year of follow-up (Quadratic ΔeGFR=0.32±5.78ml/min/1.73m2) as opposed to Schwartz formula that can falsely classify children in a hyperfiltration state ΔeGFR=7.51±19.46ml/min/1.73m2), p=0.019.

In this work, we proposed a novel design of microfluidic mixer utilizing the amplified Marangoni chaotic advection induced by AC continuous electrowetting of a metal droplet situated in electrolyte solution, due to the linear and quadratic voltage-dependence of flow velocity at small or large voltages, respectively. Unlike previous researchers exploiting the unidirectional surface stress with DC bias at droplet/medium interface for pumping of electrolyte where the resulting flow rate is linearly proportional to the field intensity, dominance of another kind of dipolar flow pattern caused by local Marangoni stress at the drop surface in sufficiently intense AC electric field is demonstrated by both theoretical analysis and experimental observation, which exhibits a quadratic growth trend as a function of the applied voltage. The dipolar shear stress merely appears at larger voltages and greatly enhances the mixing performance by inducing chaotic advection between the neighboring laminar flow. The mixer design developed herein, on the basis of amplified Marangoni chaotic advection around a liquid metal droplet at larger AC voltages, has great potential for chemical reaction and MEMS actuator applications, because of generating high-throughput and excellent mixing performance at the same time.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

Over the last two decades, a considerable amount of equipment has been acquired (spreaders, seeders, sprayers, among others) to respond to the challenges of Precision Agriculture (PA) concept. Most of this equipment has been purchased at a high cost. However, many of them, despite still being functional and equipped with sensors, actuators, and electronic processing units capable of adjusting to variations in speed, have become obsolete in terms of communication, and incompatible with new monitoring and control systems based on the “Isobus” protocol. This work aims to present a solution for updating the control system (“Ferticontrol”) of a “Vicon RS-EDW” spreader with variable rate application (VRA), making it compatible with the “InCommand” system from “Ag Leader”. The solution includes low-cost “Arduino” and “Raspberry Pi” microcontrollers and open-source software. The development shows that it is possible to implement a solution that is accessible to farmers in general. It also provides a niche business opportunity for young researchers to set up small technology-based enterprises associated with universities and research centers. These partnerships guarantee permanent innovation and represent a decisive step towards modern, technological, competitive, and sustainable agriculture.

Ultrafast chip nanocalorimetry opens up remarkable possibilities in materials science by allowing samples to be cooled and heated at extremely high rates. Due to heat transfer limitations, controlled ultrafast cooling and heating can only be achieved for tiny samples in calorimeters with a micron-thick membrane. Even if ultrafast heating can be controlled under quasi-adiabatic conditions, ultrafast controlled cooling can be performed if the calorimetric cell is located in a heat-conducting gas. It was found that the maximum possible cooling rate increases as 1/r0 with decreasing radius r0 of the hot zone of the membrane. The possibility of increasing the maximum cooling rate with decreasing r0 was successfully implemented in many experiments. In this regard, it is interesting to answer the question: what is the maximum possible cooling rate in such experiments if r0 tends to zero? Indeed, on submicron scales, the mean free path of gas molecules lmfp becomes comparable to r0, and the temperature jump that exists at the membrane/gas interface becomes significant. Considering the limitation associated with thermal resistance at the membrane/gas interface and considering the transfer of heat through the membrane, we show that the controlled cooling rate can reach billions of K/s, up to 1010 K/s.

Lots of efforts are made to optimize spectrum quality used for indoor farming to maximize artificial light utilization and reduce water loss. For such an improvement, green (G) light supplementation to a red-blue (RB) background was successfully employed in our previous studies to restrict both non-photochemical thermal dissipation (NPQ) and stomatal conductance (gs). At the same time, however, the downregulation of NPQ and gs influences the leaf temperature (Tleaf) in opposite ways. Thus, to elucidate which factor plays a more prominent role in Tleaf regulation and whether such response is temporal or permanent we investigated the correlation between NPQ or gs and the subsequent Tleaf. To this end, we analysed tomato plants (Solanum lycopersicum L. cv. Malinowy Ozarowski) grown solely under monochromatic LED lamps (435, 520, or 662 nm; 80 µmol m–2 s–1) or under mixed RGB spectrum (1:1:1; 180 µmol m–2 s–1), and simultaneously measured the gs and Tleaf with an infrared gas analyser and thermocouple or employed infrared thermal camera (FLIR) during thermal imaging analyses. Results documented that growth light quality significantly modified the Tleaf, and such response is not temporal. Furthermore, we found that plants' actual adaxial leaf surface temperature is more closely related to NPQ amplitude, while the temperature of the abaxial surface corresponds to gs.

Mixing layer height (MLH) is a crucial parameter for air quality modelling that is still not routinely measured. Common methods for MLH determination use atmospheric profiles recorded by radiosonde but they suffer from course temporal resolution since balloon launching is only twice a day. Recently cheap ceilometers are gaining popularity in the retrieval of MLH diurnal evolution based on aerosol profiles. This study presents a comparison of a proprietary (Jenoptik) and a free available (STRAT) algorithms to retrieve MLH diurnal cycle. The comparison is accomplished in summer season over urban area and radiosonde data is used to estimate MLHs according to parcel, lapse rate, and Richardson methods (the last algorithm is used as a reference in the study) in addition. It was found that STRAT and Jenoptik give lower MLH than radiosonde with an underestimation of about 150m and 650m respectively. Additionally, STRAT showed reasonable performance in tracking of MLH diurnal evolution. Daily MLH maximum of about 2000m was found in the late afternoon (18-19 LT). In contrast, Jenoptik algorithm showed more weaknesses, mainly attributed to its real-time operation and independent processing of a single profile. At night and during morning transition period, both lidar-based methods showed difficulties as MLH was often in the ceilometer’s incomplete overlapping zone so residual or advected aerosol layers aloft were misleadingly reported as mixing layer (ML).

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

In bilingual communities, social interactions take place in both single- and mixed-language con-texts. Some of the information shared in multilingual conversations is often required in conse-quent social encounters, like interlocutors’ personal information. In this study we explored whether the autobiographical information provided in a single-language context is better re-membered than in an equivalent mixed-language situation. More than 400 Basque-Spanish bilin-gual (pre-)teenagers were presented with new persons who introduced themselves by either using only Spanish or only Basque, or by inter-sententially mixing both languages. Different memory measures were collected immediately after the initial exposure to the new pieces of information (immediate recall and recognition) and on the day after (delayed recall and recognition). In none of the time points was the information provided in a mixed-language fashion worse remembered than that provided in a strict one-language context. Interestingly, the variability across partici-pants in their sociodemographic and linguistic variables had a negligible impact on the effects. These results are discussed considering their social and educational implications for bilingual communities.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Anaerobic digestion is a biological process that transforms high-strength organic effluents into biogas with multiple benefits. However, concurrent with organics' biological transformation, a liquid phase with a high solid content is also derived from this process. Valorizing this fraction is not an easy task if an agronomic application cannot be considered as a suitable option. The thermal valorization of this fraction allows for energy extraction, but also gives rise to additional capital investment and increases the energy demand of the global process. In addition, the thermal treatment of digestate has to deal with a mineralized material. The changes in organic matter due to anaerobic stabilization were studied in the present manuscript, by evaluating the thermal behavior of samples, activation energy and organic transformation using FTIR spectroscopy. Digested samples of a mixture composed of manure and glycerin (5% v/v) were studied. The stabilization caused a dramatic decrease in aliphatic compounds, greatly increasing the mineral content of the sample. Thermal valorization of digestates must consider the lower energy content and more complex structure of these materials, with higher content of lignin and protein-type compounds.

Melioidosis is an endemic infectious disease caused by Burkholderia pseudomallei bacteria, which contaminates soil and water. To better understand the environmental changes that have contributed to melioidosis outbreaks, this study used spatiotemporal analyses to clarify the distribution pattern of melioidosis and the relationship between melioidosis morbidity rate and local environmental indicators (land surface temperature, normalised difference vegetation index, normalised difference water index) and rainfall. A retrospective study was conducted from January 2013 to December 2022, covering data from 219 sub-districts, with each exhibiting varying morbidity rate of melioidosis on a monthly basis. Spatial autocorrelation was determined using local Moran’s I, and the relationship between melioidosis morbidity rate and the environmental indicators was evaluated using geographically weighted Poisson regression. The results revealed clustered spatiotemporal patterns of melioidosis morbidity rate across sub-districts, with hotspots predominantly observed in the northern region. Furthermore, we observed a range of coefficients for the environmental indicators, varying from negative to positive, which provided insights into their relative contributions to melioidosis in each local area and month. These findings highlight the presence of spatial heterogeneity driven by environmental indicators and underscore the importance of public health offices implementing targeted monitoring and surveillance strategies for melioidosis in different locations.

In Active Flow Control (AFC) applications, to activate the boundary layer the use of pulsating flow has notorious energy advantages versus constant blowing/suction jet injections. For a given AFC application, five parameters, jet location and width, inclination angle, frequency of injection and momentum coefficient need to be tuned. Two main devices are nowadays capable of injecting pulsating flow with the sufficient momentum coefficient to delay the boundary layer separation, these are the Zero Net Mass Flow actuators (ZNMFA) and the Fluidic Oscillators (FO). In the present research, a novel FO configuration is analyzed for the first time at relatively high Reynolds numbers, fluid is considered as incompressible. After obtaining the typical linear correlation between the incoming Reynolds number and the outlet flow oscillating frequency, the effect of outlet width and mixing chamber wedge inclination angle dimensional modifications is addressed, modifications of the outlet width are observed to create large variations on the FO performance. The origin of the self-sustained oscillations is also analyzed in the present manuscript and greatly helps in clarifying the forces acting on the jet inside the mixing chamber. In fact we can conclude saying that the current FO configuration is pressure driven although the mass flow forces appear to be a much more relevant than in previous FO configurations studied.

Artificial Intelligence and especially machine learning have noticed rapid advancement on image processing operations. However, its involvement in the architectural design is still in its initial stages compared to other disciplines. Therefore, this paper addresses the issues of developing an integrated bottom up digital design approach and details a research framework for the incorporation of Deep Convolutional Generative Adversarial Network (GAN) for early stage design exploration and generation of intricate and complex alternative facade designs for urban infill. This paper proposes a novel building facade design by merging two neighboring building’s architecture style, size, scale, openings, as reference to create a new building design in the same neighborhood for urban infill. This newly produced building contains the outline, style and shape of the parent buildings. A 2D urban infill building design is generated as a picture where 1) neighboring buildings are imported as a reference using mobile phone and 2)iFACADE decode their spatial adjacency. It is depicted the iFACADE will be useful for designers in the early design stage to generate new façades depending on existing buildings in a short time that will save time and energy. Besides, building owners can use iFACADE to show their architects their preferred architecture facade by mixing two building styles and generating a new building. Therefore, it is depicted that iFACADE can become a communication platform in the early design stages between architects and owners. Initial results properly define a heuristic function for generating abstract design facade elements and sufficiently illustrate the desired functionality of our developed prototype.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

Smartwatches are one of the most relevant fitness trends of the past two decades, and they collect increasing amounts of health and movement data. The accuracy of these data may be questionable and requires further investigation. Therefore, the aim of the present study is to validate smartwatches for use in triathlon training. Ten different smartwatches were tested for accuracy in measuring heart rate, distance (via global navigation satellite systems, GNSS), swim stroke rates and the number of swim laps in a 50 m Olympic-size pool. The optical heart rate measurement function of each smartwatch was compared to that of a chest strap. Thirty participants (15 females, 15 males) ran five 3-minute intervals on a motorised treadmill to evaluate the accuracy of the heart rate measurements. Moreover, for each smartwatch, running und cycling distance tracking was tested over six runs of 4,000 m on a 400 m tartan stadium track, six hilly outdoor runs over 3.4 km, and four repetitions of a 36.8 km road bike course, respectively. Three swimming protocols ranging from 200 m to 400 m were performed in triplicate in a 50 m Olympic-size pool, evaluating tracked distance and detected number of strokes. The mean absolute percentage errors (MAPEs) for the average heart rate measurements varied between 3.1% and 8.3%, with the coefficient of determination ranging from 0.22 to 0.79. MAPE results ranged from 0.8% to 12.1% for the 4,000 m run on the 400 m track, from 0.2% to 7.5% for the 3.4 km outdoor run, and from 0.0% to 4.2% for the 36.8 km bike ride. For the swimming tests, in contrast, the deviations from the true distance varied greatly, starting at a 0.0% MAPE for the 400 m freestyle and reaching 91.7% for the 200 m medley with style changes every 25 m. In summary, for some of the smartwatches, the measurement results deviated substantially from the true values. Measurements taken while road cycling over longer distances with only a few curves were in relative terms more accurate than for outdoor runs and even more accurate than for the 400 m track. In the swimming exercises, the accuracy of the measured distances was severely deteriorated by the medley changes among the majority of the smartwatches. Altogether, the results of this study should help in assessing the accuracy and thus suitability of smartwatches for general triathlon training.

In the Internet of Things (IoT) era, Mobile Edge Computing (MEC) significantly enhances the efficiency of smart devices but is limited by battery life issues. Wireless Power Transfer (WPT) addresses this issue by providing a stable energy supply. However, effectively managing overall energy consumption remains a critical and under-addressed aspect for ensuring the network’s sustainable operation and growth. In this paper, we consider a WPT-MEC network wit user cooperation to migrate the double near-far effect for the mobile node (MD) far from the base station. We formulate the problem of maximizing long-term computation rates under a power consumption constraint as a multi-stage stochastic optimization (MSSO) problem. This approach is tailored for a sustainable WPT-MEC network, considering the dynamic and varying MEC network environment, including randomness in task arrivals and fluctuating channels. We introduce a virtual queue to transform the time-average energy constraint into a queue stability problem. Using the Lyapunov optimization technique, we decouple the stochastic optimization problem into a deterministic problem for each time slot, which can be further transformed into a convex problem and solved efficiently. Our proposed algorithm works efficiently online without requiring further system information. Rigorous mathematical analysis shows that our algorithm achieves O(1/V),O(V) trade-off between computation rate and queues stability. Extensive simulation results demonstrate that our proposed algorithm outperforms baseline schemes, achieving approximately 4% enhancement while maintain the queues stability.

Bicycle transport stands at the forefront of sustainable mobility initiatives, a cornerstone of European Union policy. While support for cycling is crucial, its advancement hinges upon the presence of high-quality, secure infrastructure for cyclists. Safety emerges as a paramount concern, influencing the viability of cycling as a mode of transportation, yet its perception varies among user demographics. Considering this, this article endeavours to examine and contrast cycling infrastructure across various European nations, alongside analysing statistics pertaining to fatal traffic accidents involving cyclists. In our paper, we have chosen the Netherlands as a representative of building quality cycling infrastructure with many years of experience, and two countries that are developing conditions for cyclists, Slovakia and Poland. We have applied a correlation between the length of the transport infrastructure and the number of cyclists killed. The findings point to the substantial correlation between the quality of cycling infrastructure and the incidence of accidents. This correlation underscores the pressing need for robust infrastructure development and safety measures to bolster cycling as a safe and viable transportation option. We have employed the Shapiro-Wilk test for normal distribution to verify the input data and process the Pearson correlation to investigate the correlation between cycling infrastructure and road accident fatalities of cyclists.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P<0.05), left hippocampus volume (LHV, β: -0.02435, P<0.01) and right hippocampus volume (RHV, β: -0.02544, P<0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P<0.05) and LHV (β: -0.01173, P<0.05) and RHV (β: -0.01193, P<0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P<0.05; RHV, β: -0.005527, P<0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

A discharge mixing zone (DMZ) is a defined geographical area or volume of water in the receiving environment of a discharge where initial dilution of the effluent occurs and where exceedance of water quality criteria may be permitted. DMZs are essential to inform determination of discharge consent conditions and an important element of risk management frameworks to reduce any effects of the discharges on the environment and human health. In this review, we describe the principles and technical application of DMZs. We present an overview of the physical processes that govern the dispersion and dilution of wastewater discharges and the fate of contaminants in coastal environments and define key criteria for determining the size of DMZs. We summarize DMZ requirements in international legislation and guidance and exemplify their application to different types of discharges by means of case studies. The selected case studies illustrate different modelling tools for defining DMZs and different monitoring approaches to assess their effectiveness in achieving ecological and human health objectives.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Hybrid renewable energy systems (HRES), complemented by pumped hydropower storage (PHS), have become increasingly popular amidst the increase of renewable energy penetration. This con-figuration is even more prosperous in remote regions that are typically not connected to the mainland power grid, where the energy independence challenge intensifies. This research focuses on the design of such systems, from the perspective of establishing an optimal mix of renewable sources that takes advantage of their complementarities and synergies, combined with the versatility of PHS. However, this design is subject to substantial complexities, due to the multiple objectives and constraints to fulfill, on the one hand, and the inherent uncertainties as well, that span over all underlying processes, i.e., external, and internal. In this vein, we utilize a proposed HRES layout for the Aegean Island of Sifnos, Greece, to develop and evaluate a comprehensive simulation-optimization scheme in deterministic and, eventually, stochastic setting, revealing the design problem under the umbrella of uncertainty. In particular, we account for three major uncertain elements, namely the wind velocity (natural process), the energy demand (anthropogenic process), and the wind-to-power conversion (internal process, expressed in terms of a probabilistic power curve). Emphasis is also given to the decision-making procedure, which requires a thorough interpretation of the uncertainty-aware optimization outcomes. Finally, since the proposed PHS uses the sea as the lower reservoir, additional technical challenges are addressed.

The present investigation focuses on the impact of jet nozzle orientation on mixing time in a cylindrical tank. The aim is to identify nozzle positions that improve mixing performance and to elucidate the governing parameters that influence it. A water tank was employed for the experiment. The vertical inclination angle (α) and the horizontal inclination angle (β) of the jet nozzle determined the nozzle positions. Mixing time was determined using an inert tracer and spectrophotometry measurements. The findings show that the mixing time is significantly influenced by the position of the jet nozzle position. The accuracy of existing jet turbulence and the circulation models for the prediction of mixing time was evaluated for the different nozzle positions. Our results indicate that both models provide accurate predictions for the conventional centrally aligned (β = 0°), upward-pointing jet nozzle positions only (α > 0). For the other nozzle positions where β > 0° and at varying α, the data follow the same trends as the jet turbulence and circulation models, however, the proportionality constants vary. Shorter mixing times can be attributed principally to longer jet path lengths and therefore higher fluid entrainment and circulation, as well as higher dissipation rates per jet length squared. However, it is suspected that the 3-dimensional nature of the flow pattern generated in the tank also plays a non-negligible role since mixing is hindered when the nozzle points more towards the tank wall.

The turbulent Poiseuille flow between two parallel plates is one of the simplest possible physical situations, and it has been studied intensively. In this paper, we propose a modified Prandtl-van Driest mixing length that satisfies both boundary conditions and wall damping effects. With our new formulations, we numerically solve the problem and, moreover, propose an approximate analytical solution of mean velocity. As applications of our solution, an approximate analytical friction coefficient of turbulent Poiseuille flow is proposed.

One of the factors in the mobility of a nation's economy is the stock exchange which plays a decisive role in sustainable economic development. Accordingly, and for the special place of the stock exchange in the economy, we decided to investigate the relationship between the interest and exchange rates and the Tehran stock exchange dividend and price index (TEDPIX). Using the autoregressive distributed lag method, the present study is conducted utilizing the annual data over the period of 1991 to 2020. The results indicate that the exchange rate has a positive long-run relationship with the TEDPIX, but no statistically significant relationship was found between the TEDPIX and the interest rate. Furthermore, the results of the estimation of the error correction model show that 30.786% of the disequilibrium in each period is adjusted to the long-run equilibrium.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

Accurate estimation of livestock carrying capacity (LCC) and implementing an appropriate actual stocking rate (ASR) is key to sustainable management of grazing adapted alpine grassland ecosystems. Reliable determination of aboveground biomass is fundamental to these determinations. Peak aboveground biomass (AGBP) captured from satellite data at the peak of the growing season (POS) is widely used as a proxy for annual aboveground biomass (AGBA) to estimate LCC of grasslands. Here we demonstrate limitations of this approach and highlight the ability of POS in the estimation of ASR. We develop and trail new approaches that incorporate remote sensing phenology timings of grassland response to grazing activity, considering relations between biomass growth and consumption dynamics, in efforts to support more accurate and reliable estimation of LCC and ASR. Results show that based on averaged values from large-scale studies of alpine grassland on the Qinghai-Tibet Plateau (QTP), differences between AGBP and AGBA underestimate LCC by about 31%. Findings from a smaller-scale study that incorporate phenology timings into estimation of annual aboveground biomass reveal that Haibei alpine meadows were overgrazed by 11.5% during the study period from 2000-2005. The methods proposed can be extended to map grassland grazing pressure by predicting LCC and tracking ASR, thereby improving sustainable resource use in alpine grasslands.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

This study innovatively assesses the Mun River flow components in Thailand, integrating Artificial Neural Networks (ANN) and Isotopic (18O) End-Member Mixing Analysis (IEMMA). It quantifies the contributions of the Upper Mun River (UMR) and Chi River (CR) to the overall flow, revealing a discrepancy in their estimated contributions. ANN predicts the UMR and CR contribute approximately 70.1% and 29.5% respectively, while IEMMA indicates a more pronounced disparity with 84% from UMR and 16% from CR. This divergence highlights the distinct perspectives of ANN, focusing on hydrological data patterns, and IEMMA, emphasizing isotopic signatures. Despite discrepancies, both methods validate UMR as a significant contributor to the overall flow, highlighting their utility in hydrological research. The findings underscore the complexity of river systems and advocate for an integrated approach of river flow analysis for a comprehensive understanding, crucial for effective water resource management and planning.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

Vehicle re-identification research under surveillance cameras has yielded impressive results. However, the challenge of Unmanned Aerial Vehicle (UAV)-based vehicle re-identification (ReID) presents a high degree of flexibility, mainly due to complicated shooting angles, occlusions, low discrimination of top-down features, and significant changes in vehicle scales. To address this, we propose a novel Dual Mixing Attention Network (DMANet) to extract discriminative features robust to variations in viewpoint. Specifically, we first present a plug-and-play Dual Mixing Attention Module (DMAM) to capture pixel-level pairwise relationships and channel dependencies, where DMAM is composed of Spatial Mixing Attention (SMA) and Channel Mixing Attention (CMA). First, the original feature is divided according to the dimensions of spatial and channel to obtain multiple subspaces. Then, a learnable weight is applied to capture the dependencies between local features in the mixture space. Finally, the features extracted from all subspaces are aggregated to promote their comprehensive feature interaction. Moreover, the DMAM can be readily inserted into backbone networks at any depth to improve vehicle discrimination. The experiments show that the proposed structure gains a better performance compared with the representative methods in the UAV-based vehicle ReID task. Our code and models will be publicly released.

The aim of work is to derive an explicit expression for a function of vertical mixing induced by wind-waves. To this end, in the Navier-Stokes equations, a current is decomposed into four constituents: the mean flow, the wave-orbital motion, the wave-induced turbulent and the background turbulent currents. This decomposition allows separating the wave-induced Reynolds stress, Rw, from the background one, Rb. To make a statistical closure for Rw, the Prandtl approach for the background turbulent fluctuations is used that results in an implicit expression for the wave-induced vertical mixing function, Bv. Expression for Bv is specified based on the author’s results for the eddy viscosity found earlier in the frame of the three-layer concept for a wavy air–sea interface, used for modelling wind-drift currents [1]. Finally, the explicit parameterization for Bv(a, u*, z) is found as a linear function in both the wave amplitude at depth z, a(z), and the friction velocity in the air, u*. The linear dependence of function Bv(a) on the wave amplitude provides the enhanced vertical mixing induced by wind–waves in comparison with function Bv(a) having the cubic dependence found in [2], as far as the wind-wave amplitude a(z) decays exponentially with depth.

(1)Background:The purpose of the study was conducted to investigate the recovery of heart rate according to the performance level and rest interval conditions during 65%1RM bench press exercise;(2)Methods:The subjects of this study were eight healthy male college studentsin their 20 (years) attending University C. 1RM was measured before theexperiment, and the exercise sequence of six rest intervals (30sec, 1, 2, 3, 4,5min) was randomly selected and cross-distribution experiment. The experimental measurement was conducted a total of six times according to the rest interval condition (six conditions) once every 3 days to minimize the learning effect. The data was verified with repeated measures Two-way ANOVA and Contrast's repeated method was applied for post-comparison;(3)Results: First, the amount of exercise and the number of repetitions statistically substantially dropped (p<.001) as the number of sets rose, and a greater decline was shown when the rest periods got shorter. Second, the heart rate after exercise was increased significantly (p<.01) as the set progressed in the long rest interval conditions (4, 5min), and the heart rate after rest was increased statistically significantly (p<,05) as the set progressed in the short rest interval conditions (30sec, 1min). Third, the heart rate recovery rate (%) was able to perform more repetitions than in the short rest interval condition due to the relatively high physiological recovery of the neuromuscular and circulatory system under the long rest interval condition;(4)Conclusions: Therefore, according to the rest conditionduring the 65%1RM bench press exercise conducted in this study, the restinterval condition of 2~3min may be effective in improving muscular endurance,and the rest interval condition of 4~5min may be effective in improving muscular hypertrophy. As a result of this study, there was a significant difference in exercise performance (repetition) and physiological recovery depending on the rest interval condition according to the set progress during the same intensity resistance exercise. Through this, it is judged that it is possible to adjust the amount of exercise appropriate for the purpose of training by adjusting not only the intensity during resistance exercise but also the rest interval between sets.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

: To improve the efficiency of rhizobial inoculation operations and address the current situation of rhizobial inoculation being labor-intensive, a spraying and control system for variable rate application (VRA) of liquid rhizobia was developed. The system can accurately regulate the spraying rate of liquid rhizobia according to the desired rate of rhizobia by incremental Proportional Integral Derivative (PID) closed-loop control algorithm, making it particularly suitable for precise spraying with small amounts. In the laboratory experiment of precise flow control, variation coefficient of spraying nozzle from 0.10 MP to 0.20 MP pressure were no more than 1.2%. A clear linear relationship was observed between the spraying rate and pressure. The maximum response time was 1.93 seconds, while the average response time was 1.62 seconds when controlling the spraying system for small amounts. Field trial was conducted in Heilongjiang Agricultural Xianghe Farm of China. Average seeds number and 100-seed weight of soybean plant with rhizobia inoculation treatment were better than control group, and average yield of spraying liquid rhizobia agent with full base fertilizer increased by 232.5 kg/hm2, representing a significant 7.4% improvement over the control group. The results of these trails clearly showed the positive effect of the spraying and control system for liquid rhizobial inoculation, which has superior to existing inoculation manners, and provides an important technical support for the widespread adoption of rhizobia technology.

The proximal part of the colon offers opportunities to prolong the absorption window following oral administration of a drug. In this work, we used computer simulations to understand how the hydrodynamics in the proximal colon might affect the release from dosage forms designed to target the colon. For this purpose, we developed and compared three different models: a completely-filled colon, a partially-filled colon and a partially-filled colon with a gaseous phase present (gas-liquid model).The highest velocities of the liquid were found in the completely-filled model, which also shows the best mixing profile, defined by the distribution of tracking particles over time. No significant differences with regard to the mixing and velocity profiles were found between the partially-filled model and the gas-liquid model. The fastest transit time of an undissolved tablet was found in the completely-filled model. The velocities of the liquid in the gas-liquid model are slightly higher along the colon than in the partially-filled model. The filling level has an impact on the exsisting shear forces and shear rates, which are decisive factors in the development of new drugs and formulations.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

In this study the impact of terrorist attacks on exchange rate is estimated. Particularly, the study focuses on Turkish terrorist attacks and its implication on Turkish lira versus pound sterling exchange rate. In order, to find the causal effect the study employed Autoregressive distributive lag (ARDL) bound testing approach as an estimation technique. Accordingly, the analysis reveals that terrorist attack has a negative impact on the exchange rate in both short and long-run. However, the negative effect of terrorism tends to be small in both the short-run and long-run. More precisely, terrorist attack depreciates the exchange rate between Turkish lira and pound sterling by approximately 0.00072 in the next trading day. The long-term effect also shows that terrorist attack depreciates the exchange rate on average by 0.00212.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

The exact similarity solutions of two dimensional laminar boundary layer were obtained by Blasius in 1908, however, for two dimensional turbulent boundary layers, no similarity solutions (special exact solutions) have ever been found. In the light of Blasius' pioneer works, we extend Blasius similarity transformation to the two dimensional turbulent boundary layers, and successfully transform the two dimensional turbulent boundary layers partial differential equations into a single ordinary differential equation. By author's Maple code, we numerically solve the ordinary differential equation and produce some useful quantities.

Magnesium hydroxide continuous coagulation process was used for treating simulated reactive orange wastewater in this study. Effects of mixing conditions and retention time on the coagulation performance and floc properties of magnesium hydroxide were based on the floc size distribution (FSD), zeta potential and floc morphology analysis. Floc formation and growth in different reactors were also discussed.The results showed that increasing rapid mixing speed led to a decrease in the final floc size. Floc formation process was mainly carried out in rapid mixer, rapid mixing speed of 300rpm was chosen according to zeta potential and removal efficiency. Reducing retention time caused relatively small floc size in all reactors. When influent flow is 30 L/h (retention time of 2min in rapid mixer), the average floc size reached 8.06μm in rapid mixer, through breakage and re-growth, the floc size remained stable in flocculation basin. After growth, the final floc size reached to 11.21μm in sedimentation tank. The removal efficiency of reactive orange is 89% in magnesium hydroxide coagulation process.

We propose a new technique to prepare statistically-robust benchmarking data for evaluating chemical transport model meteorology and air quality parameters within the urban boundary layer. The approach employs atmospheric class-typing, using nocturnal radon measurements to assign atmospheric mixing classes, and can be applied temporally (across the diurnal cycle), or spatially (to create angular distributions of pollutants as a top-down constraint on emissions inventories). In this study only a short (<1-month) campaign is used, but grouping of the relative mixing classes based on nocturnal mean radon concentrations can be adjusted according to dataset length (i.e., number of days per category), or desired range of within-class variability. Calculating hourly distributions of observed and simulated values across diurnal composites of each class-type helps to: (i) bridge the gap between scales of simulation and observation, (ii) represent the variability associated with spatial and temporal heterogeneity of sources and meteorology without being confused by it, and (iii) provide an objective way to group results over whole diurnal cycles that separates ‘natural complicating factors’ (synoptic non-stationarity, rainfall, mesoscale motions, extreme stability, etc.) from problems related to parameterizations, or between-model differences. We demonstrate the utility of this technique using output from a suite of seven contemporary regional forecast and chemical transport models. Meteorological model skill varied across the diurnal cycle for all models, with an additional dependence on the atmospheric mixing class that varied between models. From an air quality perspective, model skill regarding the duration and magnitude of morning and evening “rush hour” pollution events varied strongly as a function of mixing class. Model skill was typically the lowest when public exposure would have been the highest, which has important implications for assessing potential health risks in new and rapidly evolving urban regions, and also for prioritizing the areas of model improvement for future applications.

The paper proposes a mechanism for the impact of changes in the key rate on the volume of newly issued loans. The volume depends on the price (interest rates on loans), and the price depends on the key rate and the actual consumption of loans in the previous period (generalized cobweb cycle). The model was estimated by a Kalman filter, adequacy was confirmed by simulation. It is possible to forecast the average rate on loans for a month in advance according to the information published by the Central Bank of the Russian Federation (CB). By playing various scenarios for changing the key rate, it was found that in quiet periods of economic development, the usual laws of supply and demand operate in the loan market and by raising the key rate, you can reduce inflation. In the turbulent (overheated) state of the economy, an increase in the key rate can, on the contrary, provoke an increase in the issuance of loans and unconventional manipulations with the key rate are required.

Average of 41,900 patients are diagnosed annually with staphylococcus bacterial infection in California, 24,089 patients have Methicillin-resistant Staphylococcus Aureus (MRSA) and 17,810 patients have Methicillin-Sensitive Staphylococcus (MSSA). This paper demonstrates that there is a difference in mortality rate due to staphylococcus infection between males and females (P-value<0.05, CI 95%). Male patient diagnosed with S. aureus has 1.3 chance of mortality incidence than female patient. In addition, MRSA infection rate is 1.4 times MSSA infection (P-value<0.05, CI 95%), but the gap of infection is decreasing; however, mortality of both infections combined are more than threefold greater compared to three decades ago.

In real financial markets, the certainty equivalent rate is an important factor for investors to consider. From the value of a specific company’s certainty equivalent rate, investors can judge if this company is worth investing in. In this paper, we will explore how to obtain the value of the certainty equivalent rate so that we can evaluate a given company. First, we will introduce the theoretical support of this paper, which is put-call parity. From put-call parity, we will derive the mathematical expression for the certainty equivalent rate. Second, we will use the mathematical expression for the certainty equivalent rate to perform an empirical study. We will consider some extreme examples, including some of the best- and worst-performing stocks up to this point in 2023. Based on these stocks’ data, we will visualize the performance of these stocks and explain the meaning of the data. Finally, we will apply the results to a very popular industry—the electric vehicle industry—to explore the current electric vehicle market situation in the U.S.A.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

Obesity is a risk factor for the development of gestational diabetes mellitus (GDM). However, the most optimal type of nutritional intervention to prevent GDM in high-risk women is not clearly defined. This study investigates if nutritional treatment based on the Mediterranean diet (MedDiet) before 12th gestational week (GW) in women at high risk due to a body mass index (BMI)≥25kg/m2, reduces the rate of GDM and metabolic syndrome (MetS) at 3 years postpartum. We performed a post-hoc analysis of the San Carlos Gestational Prevention Study. A total of 735 women with BMI≥25kg/m2 were evaluated between 2015-2018, 246 in standard diet control group (CG) and 489 in MedDiet intervention group (IG). The rate of GDM was significantly lower in IG compared to CG (25.1%vs31.7%;p=0.037). Postnatal follow-up was completed by 141 women in CG (57%) and 312 women in IG (64%). At 3 years postpartum, we observed a reduction (relative risk 95% confidence interval) in the rates of impaired fasting glucose (IFG) (0.51 (0.28-0.92);p=0.019), obesity (0.51 (0.28-0.92),p=0.041), waist circumference (WC)≥89.5cm (0.54 (0.31-0.94);p=0.022) and MetS (0.56 (0.33-0.94);p=0.003). MedDiet reduces the rate of GDM and postpartum MetS in women with BMI)≥25kg/m2, suggesting that its implementation should be routinely recommended from the first GWs.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

Vibro-fluidized dry coal beneficiation involves the unavoidable mixing of -1 mm coal dust into the fluidized bed, which compromises the stability and homogeneity of the bed density and reduces the effectiveness of fine-grained coal separation. In order to understand the features of coal powder separation and mixing (-1 mm) in a vibrating fluidized bed, as well as to achieve a uniform and stable bed density, a wide-grained dense medium consisting of -1 mm coal dust and 0.3-0.15 mm magnetite powder was homogeneously mixed in this work. The degree of density separation in the entire bed was examined, as well as the local mixing properties of the Wide-grained Dense Medium. It was discovered that when low vibrational energy was introduced at the same gas velocity, particle separation was enhanced in comparison to the usual fluidized bed. Little bubbles were found to ensnare fine coal dust and migrate upward, increasing density separation. The introduction of high vibrational energy leads to particle disorder within the bed and an increase in the level of particle mixing. The beneficial effects of vibration on the bed are diminished when the gas velocity is gradually increased under specified vibration circumstances. This causes big bubbles to develop more frequently, which increases particle mixing. Among them, the 1-0.5 mm fine-grained coal exhibits the best mixing state; it is less impacted by variations in air velocity and vibration levels, whereas the -0.5 mm coal dust is more affected by each of these variables. Furthermore, a wide range of air velocity regulation without a significant segregation state change was discovered to be achievable by the particle system under vibration circumstances of f=25Hz A=1mm and f=25Hz A=2mm.

The lack of knowledge on the link between the manufacturing process and performances constitutes a major issue of brake lining development. This study focuses on the effect of mixing duration on properties and tribological behavior of organic friction composite materials. The adopted methodology is based on efficient simplified formulations to limit synergic effects by the reduction of number and size distribution of constituents. Microstructural characteristics are analyzed and correlated to thermo physical and mechanical properties. Wear mechanisms and tribological behavior are studied in relation with the given microstructure and material properties. In the elaboration process, mixing duration has an impact on particle distribution and fibre arrangement. Distribution and size of fibre entanglements are found to cluster carbonaceous particles, which creates bulk thermal bridges improving thermal conductivity. Moreover, rockwool fibre arrangements affect density, porosity and thermo-physical properties. In addition, mixing duration disrupts cohesion of fibre bundles with the matrix, affecting compressive modulus and wear behaviour. This microstructural defect fosters an abundant third-body source flow, which results in a high wear flow. Porosities induced by fibre entanglements, presenting large and irregular size and distribution on the friction surface, lead to a low wear resistance and change the stability of friction.

Melt mixing is a convenient method to prepare polymer nanocomposites, but the extent of the dispersion of the solid filler reached is often limited, and may compromise the anticipated performance of these materials during service. Since the efficiency of extensional flows on dispersion is now well recognized, several mixers were designed with the aim of inducing both shear and extensional flow components. This work combines experimental and numerical data to better understand the kinetics of the dispersion of graphite nanoplates in a polypropylene melt, using a mixing device that consists of a series of stacked rings with equal outer diameter and alternating larger and smaller inner diameters, thus creating a series of converging/diverging flows. Numerical simulation of the flow using the opensource OpenFOAM software assuming both inelastic and viscoelastic responses predicted the velocity, streamlines, flow type and shear and normal stress fields for the mixer. Experimental and computed data were combined to determine the trade-off between the local degree of dispersion of the PP/GnP nanocomposite, measured as Area ratio, and the absolute average value of the hydrodynamic stresses multiplied by the local cumulative residence time. From considerations based on a theoretical approach to dispersion, the cohesive strength of the GnP agglomerates studied was estimated to be in the range 3 - 10kPa.

In the present study Aprepitant (APT) ternary solid dispersions (SDs) were developed and evaluated for the first time. Specifically, ternary SDs of APT with Poloxamer 188 and Soluplus^® (SOL) were prepared via melt mixing and compared to binary APT/Poloxamer 188 and APT/SOL SDs. Initially, combined thermo-gravimetric and hot-stage polarized light microscopy studies indicated that all tested compounds were thermally stable up to 280 °C, while Poloxamer 188 acted as a plasticizer to SOL by significantly reducing the temperature required to fully solubilize the API during SD preparation. Differential scanning calorimetry combined with wide angle X-ray diffraction studies showed that crystalline API was dispersed in both binary and ternary SDs, while Fourier transformation-infrared spectroscopy studies revealed no molecular interactions among the components. Scanning electron microscopy combined with EDAX element analysis showed that the API was dispersed in nano-scale within the polymer matrices, while increasing APT content led to increasing API nano-crystals within the SDs. Finally, dissolution studies showed that the prepared formulations enhanced dissolution of Aprepitant and its mechanism analysis was further studied. A mathematical model was also investigated to evaluate the drug release mechanism

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels considering Nigeria as case study. It is found that high solar radiation in Nigeria increases surface temperature of PV panel above 25oC of optimal operating temperature of PV panels. Redundant energy gain from incident solar energy is dissipated at the rear of PV panels as heat, which reduces the efficiency of PV panel. Cooling mechanism is needed to cool the PV panels to increase the efficiency. In this study we demonstrated a unique design of a bifunctional photovoltaic-thermal (PVT) system by employing heat exchanger at the rear of PV panel and water is used as a working fluid that is circulated through the heat exchanger to remove the excess heat. It is observed from the simulation results that Maiduguri peak annual electrical power output gives 1907kWh/kWp which is the highest, because of high solar radiation average of 727W/m2 in a year. And for Makurdi the peak annual electrical power output of 1542kWh/kWp while for Port Harcourt the peak power output of 1355kWh/kWp respectively. Interestingly, Polycrystalline Si-PV surface temperature decrease from 49.25oC to 38.38oC. Electrical power increased from 1526.83W to 1566.82W in a day and efficiency increase from 13.99% to 15.01%.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

We have developed deep learning models for automatic identification of the maternal heart rate (MHR) and, more generally, false signals (FSs) on fetal heart rate (FHR) recordings. The models can be used to preprocess FHR data prior to automated analysis or as a clinical alert system to assist the practitioner. Three models were developed and used to detect (i) FSs on the MHR channel (the FSMHR model), (ii) the MHR and FSs on the Doppler FHR sensor (the FSDop model), and (iii) FSs on the scalp ECG channel (the FSScalp model). The FSDop model was the most useful because FSs are far more frequent on the Doppler FHR channel. All three models were based on a multilayer, symmetric, GRU and were trained on data recorded during the first and second stages of delivery. The FSMHR and FSDop models were also trained on antepartum recordings. The training dataset contained 1030 expert-annotated periods (mean duration: 36 min) from 635 recordings. In an initial evaluation of routine clinical practice, 30 fully annotated recordings for each sensor type (mean duration: 5 h for MHR and Doppler sensors, and 3 h for the scalp ECG sensor) were analyzed. The sensitivity, positive predictive value (PPV) and accuracy were respectively 62.20%, 87.1% and 99.90% for the FSMHR model, 93.1%, 95.6% and 99.68% for the FSDop model, and 44.6%, 87.2% and 99.93% for the FSScalp model. We built a second test dataset with a more solid ground truth by selecting 45 periods (lasting 20 min, on average) on which the Doppler FHR and scalp ECG signals were recorded simultaneously. Using scalp ECG data, the experts estimated the true FHR value more reliably and thus annotated the Doppler FHR channel more precisely. The models achieved a sensitivity of 53.3%, a PPV of 62.4%, and an accuracy of 97.29%. In comparison, two experts (blinded to the scalp ECG data) respectively achieved a sensitivity of 15.7%, a PPV of 74.3%, and an accuracy of 96.91% and a sensitivity of 60.7%, a PPV of 83.5% and an accuracy of 98.24%. Hence, the models performed at expert level (better than one expert and worse than the other), although a well-trained expert with good knowledge of FSs could probably do better in some cases. The models and datasets have been included in the Fetal Heart Rate Morphological Analysis open-source MATLAB toolbox and can be used freely for research purposes.

A new design scheme is proposed for twisting the walls of a microchannel, and its performance is demonstrated numerically. The numerical study was carried out for a T-shaped microchannel with twist angles in the range of 0 to 34π. The Reynolds number range was 0.15 to 6. The T-shaped microchannel consists of two inlet branches and an outlet branch. The mixing performance was analyzed in terms of the degree of mixing and relative mixing cost. All numerical results show that the twisting scheme is an effective way to enhance the mixing in a T-shaped microchannel. The mixing enhancement is realized by the swirling of two fluids in the cross section and is more prominent as the Reynolds number decreases. The twist angle was optimized to maximize the DOM, which increases with the length of the outlet branch. The twist angle was also optimized in terms of the relative mixing. The two optimum twisting angles are generally not coincident. The optimum twist angle shows a dependence on the length of the outlet branch but it is not affected much by the Reynolds number.

This study investigates lost foam shell casting coatings, focusing on the effects of mixing time and standing time on the viscosity and rheological properties of the coatings. The results show that the viscosity of the coating decreases with increasing mixing time and eventually stabilizes. Conversely, the viscosity initially increases and then decreases with prolonged standing time. To ensure optimal coating performance, this study determined that the mixing time should be no less than 50 minutes, and the standing time should not exceed 40 hours.

Little is known about how the degree of mixing of forest-forming species affects forest floor hydrology. We evaluated the water storage capacity of the resulting litter layer by mixing litterfall of Scots pine and sessile oak and studying their decomposition time. We prepared 90 artificial samples containing pure pine litter, pure oak litter, and mixed pine-oak litter with varying shares of pine needles. These samples were subjected to 15 months of decomposition in soil. After every three months of decay, some samples were removed from the soil, and their water storage capacity, bulk density, and C:N ratio were evaluated. Our findings indicate that samples with the greatest water storage capacity had a low C:N ratio and a predominant share of oak leaves. Conversely, samples with a high C:N ratio and a predominant share of pine needles had the lowest water storage capacity. After 12 and 15 months of decomposition, the water storage capacity increased by more than 52% compared to the initial water capacity of the samples. The highest increase in water storage capacity (>40%) was observed in samples with a predominant share of oak leaves, while the lowest (approximately 28%) was recorded in samples with 80 and 100% of pine needles.

Different values of the Hubble constant for extragalactic objects are not considered here. We give a number of examples of the extreme accordance of expansion rates of different fields of knowledge with the cosmological expansion rate. The coincidence of the expansion rates means that a common cause is almost inevitable. All these examples are gravitationally bound in themselves and in this case are subject to cosmological expansion. According to standard theory, this should not happen. We therefore question the common boundary of gravity and expansion for both theoretical and observational reasons and conclude that all gravitationally dominated objects participate in cosmological expansion or scale drift, contrary to general doctrine. The space expands with its contents while numerically maintaining distance, radius, rotation time and density. What is generally interpreted as an expansion is obviously a scale drift with a drift rate that corresponds to the size of the Hubble constant. The Earth is subject to expansion and scale drift. This results in numerically constant measured values. This drift apparently also applies to distant galaxies and other objects. The cosmological red shift is not interpreted here as a Doppler effect and numerical increase in distances, but in accordance with standard theory as an expansion or drift of the space-time scale. The expansion of the radii of galaxies makes the assumption of dark matter superfluous. The continents and our everyday environment are not subject to expansion or scale drift.

Demographic and socio-economic developments couple with other requirements to satisfy human needs result in rapid urban expansion sometimes with increasing rate of surface extent greater than the rate of growth of population, that result in continuous sealing of ground surface thereby affecting ecosystem services. This study applied remote sensing toward achieving the progress of SDGs and stage to determine the ratio of the rate of land consumption to the rate of population growth of Gombe metropolis. QGIS 2.18 was used for the image processing and classification analysis for the key Landsat ETM+ (Enhanced Thematic Mapper), Impervious Surface Indices and population data to inform on the urban trend and LCR/PGR for the periods 2000-2005, 2005-2010, and 2010-2015. The result appears that the LCR/PGR for the periods of study show split trends. During 2000-2005 the result shows that the study area expanded outward with LCR/PGR of 1.2. The result also indicate that during 2005-2010, the study area densified with little expansion with the LCR/PGR of 0.8. The result further reveals that during 2010-2015 the LCR/PGR reached 1.8. Pointing that the study area expanded outward with the rate of ground sealing getting high.

With the ever-growing emphasis on global decarbonization and rapid increases in the power density of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with Coefficient of Thermal Expansion (CTE) mismatch between components. The Al-Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as aerospace, automotive, consumer electronics, defense, EV and space. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al-Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17μm/(m·°C)) as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructure, physical and mechanical properties of these Al-Si alloys.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

Comprehensive understanding of tree characteristics and conditions holds paramount importance for the precise management of hazelnut orchards. It facilitates the determination of tree vigor, pruning requirements, phytosanitary interventions, and plant water consumption. The primary objective of this study was to explore, for the first time on a fruit tree with a bushy structure and across trees of four Italian distinct hazelnut cultivars, the efficacy of multispectral and thermal UAV (Unmanned Aerial Vehicle) technologies in assessing canopy attributes, vegetative growth, and predicting abiotic stresses. These technologies serve as tools for precision agriculture, enabling the computation of various indices such as the Normalized Difference Vegetation Index (NDVI) and crop water stress index (CWSI). The study of water content is of particular importance at this time, especially considering the increasing water stress levels in Europe as well as globally. While Red Green Blue (RGB) and thermal imagery collectively demonstrated superior performance in model reconstruction, the multispectral UAV remained more adept at characterizing size traits of hazelnut plants. Thermal images alone proved inadequate for accurately reconstructing hazelnut biometric characteristics. Furthermore, all indices were found to be cultivar-specific, underscoring the importance of conducting studies across different cultivars. The utilization of two UAVs, namely multispectral and thermal, facilitated the examination of the relationship between NDVI and CWSI across tree species.

In this paper we describe a nonparametric maximum likelihood (NPML) method for estimating multivariate mixing distributions. Given $N$ independent observations, convexity theory shows that the NPML estimator is discrete with at most $N$ support points. The original infinite NPML problem then becomes the finite dimensional problem of finding the location and probability of the support points. The probability of the support points is found by a Primal-Dual Interior-Point method; the location of the support points is found by an Adaptive Grid method. Our method is able to handle high-dimensional and complex multivariate mixture models.An important application is discussed for the problem of population pharmacokinetics and a non-trivial example is treated.Our algorithm has been successfully applied in hundreds of published pharmacometric studies. In addition to population pharmacokinetics, this research also applies to empirical Bayes estimation and many other areas of applied mathematics.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

Thermal infrared imagery provides temperature information on target objects, and has been widely applied in non-destructive testing. However, thermal infrared imagery is not always able to display detailed textures of inspected objects, which hampers the understanding of geometric entities consisting of temperature information. Although some commercial software has been developed for 3D thermal model displays, the software requires the use of expensive specific thermal infrared sensors. This study proposes a cost-effective method for 3D thermal model reconstruction based on image-based modeling. Two smart phones and a low-cost thermal infrared camera are employed to acquire visible images and thermal images, respectively, that are fused for 3D thermal model reconstruction. The experiment results demonstrate that the proposed method is able to effectively reconstruct a 3D thermal model which extremely approximates its corresponding entity. The total computation time for the 3D thermal model reconstruction is intensive while generating dense points required for the creation of a geometric entity. Future work will improve the efficiency of the proposed method in order to expand its potential applications to in-time monitoring.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Brillouin-Enhanced Four-Wave-Mixing techniques, which couple four optical beams through Brillouin nonlinearity, have gained popularity in the 1980's largely owing to their phase conjugation properties. Experiments were mainly conducted in liquid cells. The interest in Brillouin-Enhanced Four-Wave-Mixing has reawakened in the 2000's, following the quest for dynamically reconfigurable gratings in optical fibers. Termed Brillouin Dynamic Grating this time around, it is, in fact, an acoustic wave, optically generated by stimulated Brillouin scattering process between two pump waves. The acoustic wave either carries the coherent information encoded by the pump beams, or in the case of sensing applications, its properties are determined by the environmental parameters. This information, in turn, is imparted to the third phase-matched optical probe wave through the elasto-optic effect. Over the last decade, this mechanism allowed for the realization of many all-optical signal processing functions and has proven instrumental in distributed sensing applications. This paper describes the basics, as well as the state of the art, of BDG-based applications in optical fibers. It also surveys the efforts being done to carry over these concepts to the photonic chip level.

Inflation and exchange rates have great influence on consumer prices especially on imports and exports. Exchange rate fluctuations create inefficiency and distort world prices whereas changes in inflation rates have a direct impact on consumer goods prices which incidentally include exchange rates. There is a direct interdependence between inflation and exchange rates and this paper is aimed at investigating this relationship in dynamic context. It tries to find out how changes in inflation and exchange rates impact on another by adopting the econometric and copula approaches. Both inflation and exchange rates data are susceptible to volatility clustering, possess fat tails and are skewed coupled with conditional heteroskedasticity. Hence we model the univariate distributions by using ARMA$(p,q)$-GARCH$(x,y)$ so as to capture the most important stylized features of inflation and exchange rates. A bivariate model is then constructed by coupling the marginal distributions of inflation and exchange rates using the survival Clayton copula. Empirical results from monthly inflation and exchange rates data show positive correlation between the two based on Kendall $\tau$ test which confirms that a change in inflation results in change of exchange rates an vice versa hence there is co-movement. Furthermore, by the Granger causality test, exchange rates spikes cause changes in inflation rates. The results of the study have implications on economic policy design and hedging strategies for traders on imports and exports.

Conversion of electromagnetic energy into magnetohydrodynamic energy occurs when the electric conductivity changes from negligible to finite values. This process is relevant during the epoch of reheating of the early Universe at the end of inflation and before the emergence of the radiation-dominated era. We find that conversion into kinetic and thermal energies is primarily the result of electric energy dissipation and that the magnetic energy plays only a secondary role in this process. This means that, since electric energy dominates over magnetic energy during inflation and reheating, significant amounts of electric energy can be converted into magnetohydrodynamic energy when conductivity emerges early enough, before the relevant length scales become stable.

In this paper we establish information theoretical bridges between 1) Thermal Heisenberg uncertainties $\Delta x \Delta p$ (at temperature $T$), and 2) LMC structural quantifiers. After having achieved such purpose, we determine to what an extent our bridges can be extended to both the semi classical and classical realms. Also, we find a strict bound relating a special LMC structural quantifier to quantum uncertainties.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

The thermal surface properties of graphenes and carbon materials are of crucial importance in chemistry of materials, chemical engineering, and many industrial processes. (1) Background: The determination of these surface properties is carried out using inverse gas chromatography at infinite dilution which leads to the retention volume of organic solvents adsorbed on solid surfaces. This experimental and fundamental parameter actually reflects the surface thermodynamic interactions between injected probes and solid substrates. (2) Methods: The London dispersion equation and the Hamieh thermal model were used to quantify the London dispersive and polar surface energy of graphenes and carbon fibers as well their Lewis acid-base constants by introducing the coupling amphoteric constant of materials. (3) Results: The London dispersive and polar acid-base surface energies, the free energy of adsorption, the polar enthalpy and entropy, and the Lewis acid-base constants of graphenes and carbon materials were determined. (4) Conclusions: it was showed that graphene exhibited the highest values of London dispersive surface energy, polar surface energy, and Lewis’s acid-base constants. These highest characteristics of graphene justify its great potentiality and uses in many industrial applications.

In the quest for more efficient solar thermal systems, accurately determining the thermal emittance of low-emissive materials is crucial in determining the power losses. This paper describes the calorimetric method designed to precisely measure the thermal emittance of Selective Solar Absorbers (SSAs) to be used in High Vacuum Flat Plate Collectors (HVFPCs). The method's capability is demonstrated through the successful correction of thermal emittance values for copper samples of varying sizes, including dimensions down to 49 cm². Results highlight the method's potential to significantly reduce measurement errors associated with small-size and/or low-emittance samples, providing a path forward to improve the design and efficiency of SSAs. This research marks a significant step in advancing solar thermal technology by enabling emittance measurements with a precision better than 0.003, which is essential for the development of high-performance solar thermal absorbers. The method has also been applied to correct the thermal emittance value of SSA measured in previous measurement campaigns, and it allows a better estimation of the SSA efficiency conversion curve.

Introducing the Moving Least-Squares Aided Finite Element Method (MLS-FEM), we present a robust computational technique that effectively evaluates the development of mixing in polymeric mixing devices. Our approach uses the Moving Least-Squares (MLS) interpolant to enhance the classic finite element shape functions. As a result, it becomes possible to treat fixed or moving components, such as rotors of a mixer, as discontinuities within the flow domain. This allows analysis of the flow field with a background mesh independent of the rotors' shape, orientation, and position. We compared the MLS-FEM results with the classical boundary-fitted mesh FEM, which comprises the mesh regeneration steps by the movement of the rotors. We then showed that the new method provides accurate results for the flow field parameters (i.e., the velocity components and the pressure values) and the mixing evolution without requiring mesh regeneration and without compromising accuracy.