A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

Efficient heat management and control in optical devices, facilitated by advanced thermo-optic materials, is critical for many applications such as photovoltaics, thermal emitters, mode-locked lasers, and optical switches. Here, we investigate the thermo-optic properties of 2D graphene oxide (GO) films by precisely integrating them onto microring resonators (MRRs) with control over the film thicknesses and lengths. We characterize the refractive index, extinction coefficient, thermo-optic coefficient, and thermal conductivity of for the GO films with different layer numbers and degrees of reduction, including reversible reduction and enhanced optical bistability induced by photo-thermal effects. Experimental results show that the thermo-optic properties of 2D GO films vary widely with the degree of reduction, with significant polarization anisotropy, enabling efficient polarization sensitive devices. The versatile thermo-optic response of 2D GO substantially expands the scope of functionalities and devices that can be engineered, making it promising for a diverse range of thermo-optic applications.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Ice formation on aircraft surfaces poses significant safety risks, and current detection systems often struggle to provide accurate, real-time predictions. This paper presents the development and comprehensive evaluation of a smart ice control system using a suite of machine learning models. The system utilizes various sensors to detect temperature anomalies and signal potential ice formation. We trained and tested supervised learning models (Logistic Regression, Support Vector Machine, Random Forest), unsupervised learning models (K-means clustering), and neural networks (Multi-Layer Perceptron) to predict and identify ice formation patterns. Experimental results demonstrate that our smart system, driven by machine learning, accurately predicts ice formation in real-time, optimizes de-icing processes, and enhances safety while reducing power consumption. This solution holds the potential for improving ice detection accuracy in aviation and other critical industries requiring robust predictive maintenance.

In this paper we derived an expression that allows the determination of the thermo-optic coefficient of weakly-guiding germanium-doped silica fibers, based on the thermal behavior of optical fiber devices, such as, fiber Bragg gratings (FBGs). The calculations rely on the full knowledge of the fiber parameters and on the temperature sensitivity of FBGs. In order to validate the results, we estimated the thermo-optic coefficient of bulk GeO2 glass at 293 K and 1.55 m to be 18.3x10-6 K-1. The determination of this value required to calculate a correction factor which is based on the knowledge of the thermal expansion coefficient of the fiber core, the Pockels’ coefficients (p11=0.125, p12=0.258 and p44=-0.0662) and the Poisson ratio (=0.161) of the SMF-28 fiber. To achieve that goal, we estimated the temperature dependence of the thermal expansion coefficient of GeO2 and we discussed the dispersion and temperature dependence of Pockels’ coefficients. We have presented expressions for the dependence of the longitudinal and transverse acoustic velocities on the GeO2 concentration used to calculate the Poisson ratio. We have also discussed the dispersion of the photoelastic constant. An estimate for the temperature dependence of the thermo-optic coefficient of bulk GeO2 glass is presented for the 200-300 K temperature range.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

In the last decades we have experienced great social, cultural, and educational changes, spending more time performing tasks in near vision and less hours in outdoor activities, having more overexposure to digital screens, especially the youngest and increasingly from younger ages. It is common to see cases when performing tasks in near vision the posture or position of the head is not adequate, especially the youngest, being essential to have a correct posture of the head to avoid visual, muscular, or articular problems. We present a procedure to try to control the correct position of the head in real time when performing close-up activities. The aim is to detect the inclination of the head and to know if a bad position is adopted due to a visual problem or simply to inadequate visio-postural habits, warning us of the postural anomaly to correct it.

TThe locality condition of probabilities underpinning the derivation of Bell inequalities can be violated classically. The wave function collapse of an entangled state of single photons results in the factorization of quantum probabilities. It is possible to differentiate, locally, between ensemble probabilities of single detections with and without wave function collapse for the alleged quantum nonlocality. The theoretical concept of photonic quantum nonlocality cannot be implemented physically because of the quantum Rayleigh scattering of single photons. A distinction needs to be made between the correlation of individual, single measurements of pure states and the correlation of the measurement ensemble of the mixed states. The correlation operator of Pauli vector operators delivers the same probabilities of correlated detections of photons for both independent and multi-photon states as for ‘entangled’ states of photons. As single-photon sources are not needed, the design and implementation of quantum computing operations and other devices will be significantly streamlined. © 2024 The Author

Quantum Rayleigh scattering of single photons rules out coincident detections of the originally entangled, paired photons Correlations between independent states of qubits can easily outperform those calculated with entangled photons. The quantum joint probability for a Bell state can be factorized enabling a local detection of the alleged quantum nonlocality, if it existed.

Recent discoveries of potential ice particles and ice-cemented regolith on celestial bodies like the Moon and Mars have ushered in new opportunities for developing technologies to extract water, facilitating future space missions and activities on these celestial surfaces. This study delves into the potential for water extraction from regolith through an experiment designed to test water recuperation from regolith simulant under varying gravitational conditions. The resultant water vapor extracted from the regolith is re-condensed on a substrate surface and collected in liquid form. Three types of substrates, hydrophobic, hydrophilic, and grooved, are explored. The system’s functionality was assessed during a parabolic flight campaign simulating three distinct gravity levels: microgravity, lunar gravity, and Martian gravity. Our findings reveal that the hydrophobic surface demonstrates the highest efficiency due to drop-wise condensation, and lower gravity levels result in increased water condensation on the substrates. This experiment aims to provide insights into in-situ water recovery, which is pivotal for establishing economically-sustainable water supplies for future missions.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

An approximation-free and fully quantum optic formalism for parametric processes is presented. Phase-dependent gain coefficients and related phase-pulling effects are identified for quantum Rayleigh emission and the electro-optic conversion of photons providing parametric amplification in small scale integration of photonic devices. These mechanisms can be manipulated to deliver, simultaneously, sub-Poissonian distributions of photons as well as phase-dependent amplification in the same optical quadrature of a signal field.

Background: The workplace burnout syndrome is often associated with particular aspects of certain job positions, especially those which entail working with people with special needs. The burnout syndrome in healthcare jobs is a serious problem which has grown into an epidemic among healthcare workers and associates. Objectives: The aim of this research is to assess the presence of stress and burnout syndrome at work with healthcare workers, expert workers, professional associates and associates in social service institutions in Belgrade. Material and Methods: This research has been conducted in the form of a cross-sectional study of a representative sample in social institutions in Belgrade. It has been conducted from March to the end of June of 2023. The sample of the study had 491 participants. The questionnaires used were a structured instrument with social-demographic and social-economic characteristics, workplace characteristics, life style characteristics, and the following questionnaires: DASS-21, Copenhagen, Brief Resilience Scale, and Brief Resilient Coping Scale. Results: The end results indicate the following to be significant risk factors for the occurrence of workplace burnout syndrome: overtime (OR=2.62; CI=1.50-4.56), BRS average score (OR=0.28; CI=0.17-0.44), DASS21 D heightened depression (OR=2.09; CI=1.1-4.04), DASS21 A heightened anxiety (OR=2.38; CI=1.34-4.21), DASS21 S heightened stress (OR=2.08; CI=1.11-3.89). The only protective risk factor which stood out was the self-assessment of health levels (OR=0.60; CI=0.42-0.85). Conclusion: Overtime is a significant predictor of workplace burnout. Apart from it, other significant predictors of workplace burnout were heightened depression, anxiety, and stress levels.

We investigate entropy generation in unsteady three-dimensional axisymmetric MHD nanofluid flow over a non-linearly stretching sheet. The flow is subject to thermal radiation and a chemical reaction. The conservation equations were solved using the spectral quasi-linearization method. The novelty of the work is in the study of entropy generation in three-dimensional axisymmetric MHD nanofluid and the choice of the spectral quasilinearization method as the solution method. The effects of Brownian motion and thermophoresis are also taken into account when the nanofluid particle volume fraction on the boundary in passively controlled. The results show that as the Hartman number increases, both the Nusselt number and the Sherwood number decrease whereas the skin friction increases. It is further shown that an increase in the thermal radiation parameter corresponds to a decrease in the Nusselt number. Moreover, entropy generation increases with the physical parameters.

Due to their remarkable intrinsic physical properties, carbon nanotubes (CNTs) can enhance mechanical properties and confer electrical and thermal conductivity to polymers currently investigated for use in advanced applications based on thermal management. An epoxy resin filled with varying concentrations of CNTs (up to 3 wt.%) was produced and experimentally characterized. The electrical percolation curve identified two critical filler concentrations: 0.5 wt%, near the electrical percolation threshold, suitable for exploring mechanical and piezoresistive properties, and 3 wt% for investigating thermo-electric properties due to the Joule effect with applied voltages ranging from 70V to 200V. Numerical models were developed using multiphysics simulation software. Once validated with experimental data, these models were used to investigate additional physical properties of the composites. Furthermore, a statistical approach based on the design of experiments (DoE) was employed to examine the influence of certain thermal parameters on the final performance of the materials. The purpose of this research is to promote the use of contemporary statistical and computational techniques alongside experimental methods to enhance understanding of materials science. New materials can be identified through these integrated approaches, or existing ones can be more thoroughly examined.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

Advanced glycation end-products (AGEs) form through non-enzymatic glycation of various proteins. Optic nerve degeneration is a frequent complication of diabetes, and retinal AGEs accumulation is strongly linked to diabetic retinopathy development. Type 2 diabetes mellitus (T2DM) is a major risk factor for Alzheimer's disease (AD), with patients often exhibiting optic axon degeneration in the nerve fiber layer. Notably, a gap exists in our understanding of how AGEs contribute to neuronal degeneration in the optic nerve within the context of both diabetes and AD. Our previous work demonstrated that glyceraldehyde (GA)-derived toxic advanced glycation end-products (TAGE) disrupt neurite outgrowth through TAGE-β-tubulin aggregation and tau phosphorylation in neural cultures. In this study, we further illustrated GA-induced suppression of optic nerve axonal elongation via abnormal β-tubulin aggregation in mouse retinas. Elucidating this optic nerve degeneration mechanism holds promise for bridging the knowledge gap regarding vision loss associated with DM and AD.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

This study evaluated batch fermentation modes, namely, separate hydrolysis and fermentation (SHF), Quasi-simultaneous saccharification and fermentation (Q-SSF), and simultaneous saccharification and fermentation (SSF), and fermentation conditions, i.e., enzyme and yeast loadings, nutrient supplementation and sterilization, on high titer bioethanol production from SPORL-pretreated Douglas-fir forest residue without detoxification. The result indicated Q-SSF and SSF were obviously superior to SHF operation in terms of ethanol yield. The enzyme loading showed a strong positive correlation between enzyme loading and the ethanol yield. The nutrient supplementation and sterility was not necessary for ethanol production from SPORL-pretreated Douglas-fir. The yeast loading showed no significant influence on the ethanol yield for typical SSF conditions. The terminal ethanol titer of 43.2 g/L, or 75.1% theoretical based on glucose, mannose, and xylose theoretical was achieved when SSF was conducted at the condition of following: whole slurry solids loading of 15%, enzyme loading of 20 FPU/g glucan, 1.8 g/kg (wet) yeast loading, without nutrition supplementation and sterilization, at 38°C, on shake flask at 150 rpm for 96h. It is believed that with mechanical mixing, enzyme loading can be substantially reduced with affect ethanol yield by using a long fermentation time.

The purpose of this work is to analyze heat-treated ash wood at temperature of 185 ºC, in order to analyze its dimensional stability. For comparison, native ash/ not thermally treated wood, was be used. In order to analyze heat-treated ash wood, some main properties such as water absorption, swelling in thickness, roughness, Brinell hardness, modulus of rupture and elasticity, color change toward black with CIELab space, and many others properties were determined and processed. The results obtained after processing the experimental data have showed that heat-treated ash wood had good physical properties as absorption and swelling in thickness, and the slight increase in elasticity offers new fields of use. As a general conclusion of the work, it was established that the ash wood can be properly thermally treated, the dimensional stability characteristics being very good, and the decrease in bending resistance being almost imperceptible.

Current treatments in patients with pancreatic cancer offer limited benefits. In this report, we applied “alkalization therapy”, which was efficacious for other solid tumors at our clinic, to stage 4 pancreatic cancer patients, and investigated its effect on disease prognosis. Patients with metastatic pancreatic cancer who were treated at Karasuma Wada Clinic in Kyoto, Japan, between 2011 and 2022 were included in the study. All patients received alkalization therapy (combination of an alkaline diet, bicarbonate, and citric acid administration), alongside standard chemotherapy. Urine samples were collected to assess urine pH as a marker for whole-body alkalization. In the 98 patients analyzed, the median overall survival (OS) from the time of diagnosis was 13.2 months. Patients with a mean urine pH of 7.5 or greater had a median OS of 29.9 months, compared with 15.2 months for those with a mean urine pH of 6.5 to 7.5, and 8.0 months for those with a mean urine pH of less than 6.5, which suggests a trend of a longer OS in patients with a higher urine pH. Conclusions: Alkalization therapy may offer a viable approach to enhance the survival of stage 4 pancreatic cancer patients, who typically have an unfavorable prognosis.

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

A number of third order nonlinear processes can occur in single-mode fibres and an understanding of such phenomena is almost a prerequisite for actual lightwave-system designers. In this paper we review the main limitations imposed by several nonlinear effects, namely the self- and cross-phase modulation, four-wave mixing, stimulated Raman scattering and stimulated Brillouin scattering, on the performance of optical fiber communication systems.

Optic neuritis (ON) is the most common cause of vision loss in young adults. It manifests as acute or subacute vision loss, often accompanied by retrobulbar discomfort or pain on eye movements. Typical ON is associated with Multiple Sclerosis and is generally mild and steroid-responsive, whereas atypical forms are characterized by unusual features, such as optic disc edema, poor treatment response and bilateral involvement, and are often associated with autoantibodies against aquaporin-4 (AQP4) and Myelin Oligodendrocyte Glycoprotein (MOG). However, in rare cases AQP4 and MOG antibodies will come back negative, plunging the clinician in a diagnostic conundrum. Seronegative ON warrants a broad differential diagnosis, including autoantibody-associated, granulomatous, and systemic disorders. These rare forms need to be identified promptly, as their management and prognosis is greatly different. The scope of this review is to describe possible, rarer etiologies of ON when AQP4 and MOG antibodies are negative and discuss their diagnosis and treatment.

The paper presents construction, laboratory tests as well as the first field application of a new fiber-optic rotational seismograph. The system based on fiber-optic gyroscope (FOG) with determined Angle Random Walk of the order of 10-8 rad/Sqrt(s) and a few rad/s maximum detectable amplitude of rotation in the frequency range from DC to 328.12 Hz. It has been designed for rotational seismology area of interest. This work also presents exemplary relevant measurements which were conducted using a set of two devices installed in the geophysical observatory in Książ, Poland.

Temperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in hazardous working environments (air pollution, chemical or ionizing contamination), and the presence of electromagnetic disturbances. The use of fiber optic temperature sensors in polymer technology can significantly reduce the cost of their production. Moreover, the installation process and usage would be simplified. As a result, these types of sensors would becoming increasingly popular in industrial solutions. This review provides a critical overview of the latest development of fiber optic temperature sensors based on Fabry-Perot interferometer made with polymer technology.

As in glaucoma and other optic neuropathies cellular dysfunction often precedes cell death, sensitive assessment of retinal ganglion cell (RGC) function represents a key outcome measure for neuroprotective strategies aimed at targeting distressed but still viable cells. Here we offer a conceptual framework to identify progressive stages of RGC dysfunction leading to cell death in mouse models of glaucoma and other optic neuropathies based on non-invasive pattern electroretinogram (PERG), to differentiate phenotypic and altered RGC response dynamics, to assess susceptibility to stressors and to assess reversible dysfunction.

Glaucoma is a multifactorial neurodegenerative disease, characterized by degeneration of the retinal ganglion cells (RGCs). There has been little progress in developing efficient strategies for neuroprotection in glaucoma. We profiled the retina transcriptome of Lister Hooded rats at 2 weeks after optic nerve crush (ONC) and analyzed the data from the Genomic Fabric Paradigm (GFP) to bring additional insights into the molecular mechanisms of the retinal remodeling after induction of RGC degeneration. GFP considers for the expression of each gene 3 independent characteristics: level, variability and correlation with each other gene. Thus, the 17,657 quantified genes our study generated a total of 155,911,310 values to analyze. This represents 8,830x more data per condition than a traditional transcriptomic analysis. ONC led to a 57% reduction in RGC numbers as detected by retrograde labeling with DiI. We observed a higher Relative Expression Variability after ONC. Gene expression stability was used as a measure of transcription control and disclosed a robust reduction in the number of very stably expressed genes. Predicted Protein-Protein interaction (PPI) analysis with STRING revealed axon and neuron projection as mostly decreased processes, consistent with RGC degeneration. Conversely, immune response PPIs were found among up-regulated genes. Enrichment analysis showed that Complement Cascade and Notch Signaling Pathway, as well as Oxidative Stress and Kit Receptor Pathway were affected after ONC. To expand our studies of altered molecular pathways, we examined the pair-wise coordination of gene expressions within each pathway and within the entire transcriptome using Pearson correlations. ONC increased the number of synergistically coordinated pairs of genes and the number of similar profiles mainly in Complement Cascade and Notch Signaling Pathway. This deep bioinformatic study provides novel insights beyond the regulation of individual gene expression and discloses changes in the control of expression of Complement Cascade and Notch Signaling functional pathways that may be relevant for both RGC degeneration and remodeling of the retinal tissue after ONC.

Distributed fiber optic vibration sensors based on Φ-OTDR using Rayleigh backscattering of highly coherent light source pulses are very popular type in the area of sensors due to many attractive features, mainly due to its distributed manner of sensing, i.e. they can operate as thousands of local sensors simultaneously. The paper summarizes and describes several important modifications of the original sensor scheme to enhance its key performance parameters and to extend its application potential. A multi-fiber sensor form was proposed. Single- and two-fiber sensors were designed, constructed and tested both in the laboratory and in a real environment. Variants of two-fiber sensor utilizing optical switches for the sensor flexibility enhancement are proposed and their applications are described.

Introduction: Among the many factors that may limit effective wound healing in patients with chronic ulcers, bacterial infection and poor cell recruitment are primary causes that contribute to prolonged healing. Thus, a novel strategy that aims to prevent bacterial infection within the wound, while at the same time providing structural scaffolding that promotes endogenous tissue repair, would be of great interest. Here, we developed a thermo-sensitive silver nanoparticle hydrogel composite as an antibacterial nutritional scaffold for the wound that contains all nutrients required for cell growth while preventing bacterial infection with the ability to fill up all the cavities and void areas in wounds regardless of their geometry. Methods: Silver nanoparticles (AgNPs) were synthesized by chemical reduction. After characterization, silver hydrogel nanocomposite was developed by reconstitution of collagen-based hydrogel powder in a nanoparticle suspension of varying AgNPs concentrations (200, 400, and 600 ppm). The antibacterial activity of the formulations was examined in vitro and in vivo in subcutaneous implant infected model. The wound healing efficacy of the hydrogel nanocomposite was also evaluated using a splinted wound model in rats through comparison of clinical wound measurements and histological assessments. Cytocompatibility assay and biochemical analysis of blood at the end of in vivo wound healing study were performed to evaluate the safety of formulations. Results: The synthesized nanoparticles were spherical and stable. While hydrogel alone did not show any bacterial reduction in vitro, the inhibition of bacterial growth was significant in all silver hydrogel nanocomposites compared to controls (p <0.05) and was dose-dependent, with maximum reduction observed in the 600 ppm group (4.56±0.26 LOG CFU/mL, P<0.001). All concentrations of AgNPs hydrogel composites showed significant antibacterial activity in vivo as well (P<0.0001). Treatment of splinted wounds with AgNPs hydrogel composite resulted in faster wound closure and accelerated wound re-epithelialization. The formulations were non-cytotoxic and did not differ significantly in hematological and biochemical factors from the control group in in vivo study. Conclusions: By presenting promising antibacterial and wound healing activity, silver hydrogel nanocomposite offers a safe therapeutic option that can be used as a functional scaffold for an acceleration of wound healing.

In this work, three different types of sandwich structures were manufactured using Formica sheet (a paper-based sheet) as skin and perlite/sodium silicate foam as core with/without the paper honeycomb. The sandwich structures were fabricated by attaching Formica sheets on both sides of the honeycomb, perlite/sodium silicate foam, and perlite/sodium silicate foam-filled honeycomb core panels. The flexural characteristics were studied by a three-point bending test and the thermal conductivity was measured using Lee’s thermal conductivity apparatus. The results demonstrated a significant improvement in flexural properties, including core shear stress, facing stress, bending stress, and energy absorption, when incorporating the paper honeycomb reinforcement. The thermal conductivity and flexural properties were found to be well-compatible with the existing building materials for similar applications in the literature. The failure investigation revealed that the sandwiches with paper honeycomb only prematurely failed due to core buckling, whereas the foam-filled honeycomb core-based sandwiches were able to sustain higher loads, exhibiting material failures such as core shear failure, skin rapture, and delamination. It is found that the foam-filled paper honeycomb sandwich structures can withstand higher bending loads compared to foam core-based and paper honeycomb-based sandwich structures. These developed sandwiches offer potential as green materials due to the characteristics of their constituent materials and can find valuable applications in the building thermal insulation.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

Thin-film lithium niobate has gained significant attention in photonics due to its broad optical transparency, high refractive index, nonlinear coefficient, and substantial electro-optic coefficient. It holds great promise for developing electro-optic modulators with low loss, a compact size, and wide bandwidth. This study focuses on a meticulous investigation utilizing microwave photonics to establish a high-performance electro-optic modulator. Specifically, we analyze the optical mode field distribution and traveling wave electrode structure of lithium niobate thin-film materials. The proposed modulator achieves an impressive half-wave voltage-length product of 1.69 V·cm, a negligible metal loss of 0.01 dB/cm, and a substantial 3dB electro-optic bandwidth of 50 GHz. This research successfully realizes low-loss, high-efficiency LNOI electro-optical modulators, providing a strong foundation for large-scale integrated optoelectronic systems.

Telomeres, located at the ends of each chromosome play a vital role in determining cellular fate and aging. Accelerated shortening of telomeres may also result in accelerated aging and occurrence of age-related degenerative diseases. Anti-aging treatments may help in increasing the telomere length along with improving quality of life, reducing dependency for daily life activities, increasing life expectancy and reducing the risks associated with aging. In this study, we evaluated the effect of anti-aging integrative therapy in 36 individuals. The treatment included a combination of HBOT, ozone therapy, colon hydrotherapy, etc. Telomere length was used as a biomarker for objectively quantifying the outcome of the treatment. The effect of treatment was also assessed on various aging symptoms. At the end of the treatment, it was found that that 97.22% individuals showed an increase in telomere length with an average increase of 0.43 Kbp and 94.44% individuals showed reduced biological age with an average decrease of 3.8 years. These improvements were statistically significant. Improvements were also recorded in the majority of the symptoms. No major adverse events were observed. These results indicate that antiaging integrative therapy has the potential to reverse aging symptoms, cellular aging and improve quality of life.

A full potential all-electron density functional method within generalized gradient approximation is used to investigate the electronic, elastic and transport properties of cubic copper sulphide and copper selenide. The electronic structure suggests metallic behavior with a zero energy band gap for both materials. Elastic property calculations suggest a stiff material with the bulk to shear modulus ratio of 0.35 and 0.44 for Cu2S and Cu2Se respectively. The transport properties were estimated using the Boltzmann transport approach. Seebeck coefficient, electrical conductivity, thermal conductivity, and power factor all suggest a potential p-type conductivity for Cu2S and n-type conductivity for Cu2Se.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

innate and adaptive immune responses lead to wound healing by regulating a complex series of events promoting cellular cross-talk. An inflammatory response is presented with its characteristic clinical symptoms: heat, pain, redness, and swelling. Some smart thermo-responsive polymers like chitosan can be used to create biocompatible and biodegradable scaffolds with 3D architectures similar to human structures, allowing their efficient and safe use as tissue engineering and drug delivery systems in chronic wounds. Locally heated tumors above polymer lower critical solution temperature can induce its conversion into a hydrophobic form, enhancing drug release until the thermal stimulus is gone, where a lower release is due to the swelling of the material. This paper integrates the relevant reported contributions of bioengineered scaffolds for thermo-responsive drug delivery in wound healing. Therefore, we present a comprehensive review that aims to demonstrate the capacity of these systems to provide spatially and temporally controlled release strategies for one or more drugs used in wound healing. In this sense, the novel manufacturing techniques of 3D-printing and electrospinning are explored for the tuning of their physicochemical properties to adjust therapies according to the patient’s convenience, as well as reduce drug toxicity and side effects.

Magneto-optic surface plasmon resonance (MOSPR) based sensors are highly attractive as next generation biosensors. However, these sensors suffer from oxidation leading to degradation of performance, reproducibility of the sensor surface because of the difficulty of removing adsorbed materials, and degradation of sensor surface during surface cleaning, and these limit their applications. In this paper, I propose MOSPR-based biosensors with 0 to 15 nm thick inert polycarbonate laminate plastic as a protective layer and theoretically demonstrate the practicability of our approach in water-medium for three different probing samples: ethanol, propanol, and pentanol. I also investigate microstructure and magnetic properties. The chemical composition and layered information of the sensor are investigated using X-ray reflectivity and X-ray diffraction analyses and these show distinct fcc-Au (111) phases, as dominated by the higher density of conduction electrons in Au as compared to Co. The magnetic characterization measured with the in-plane magnetic field to the sensor surface for both the as-deposited and annealed multilayers showed isotropic easy axis magnetization parallel to the multilayer interface at a saturating magnetic field of <100 Oe. The sensor showed a maximum sensitivity of 5.5 × 10⁴%/RIU for water-ethanol media and the highest detection level of 2.5 × 10⁻⁸ for water-pentanol media as the protective layer is increased from 0 to 15 nm.c

Optic nerve disorders encompass a wide spectrum of conditions characterized by the loss of retinal ganglion cells (RGCs) and subsequent degeneration of the optic nerve. The etiology of these disorders can vary significantly, but emerging research highlights the crucial role of oxidative stress, an imbalance in the redox status characterized by an excess of reactive oxygen species (ROS), in driving cell death through apoptosis, autophagy, and inflammation. This review provides an overview of ROS-related processes underlying four extensively studied optic nerve diseases: glaucoma, Leber's hereditary optic neuropathy (LHON), anterior ischemic optic neuropathy (AION), and optic neuritis (ON). Furthermore, we present preclinical findings on antioxidants, with the objective of evaluating the potential therapeutic benefits of targeting oxidative stress in the treatment of optic neuropathies.

Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

Controlling surface-protein interaction during wastewater treatment is the key motivation for developing functionally modified membranes. A new biocatalytic thermo-responsive poly(vinylidene fluoride)(PVDF)/nylon-6,6/poly(N-isopropylacrylamide)(PNIPAAm) ultrafiltration membrane was fabricated to achieve dual functionality of protein-digestion and thermo-responsive self-cleaning. The PVDF/nylon-6,6/PNIPAAm composite membranes were constructed by integrating a hydrophobic PVDF cast layer and hydrophilic nylon-6,6/PNIPAAm nanofiber layer where trypsin enzymes were covalently immobilized. The immobilization density of enzymes on the membrane surface decreased with increasing PNIPAAm concentration, due to the decreased number of amine functional sites. Through a ultrafiltration study using a model solution containing BSA/NaCl/CaCl₂, the PNIPAAm containing biocatalytic membranes demonstrated a combined effect of enzymatic and thermo-switchable self-cleaning. The membrane without PNIPAAm revealed superior fouling resistance and self-cleaning with an R_PD of 22%, compared to membranes with 2 and 4 wt% PNIPAAm with 26% and 33% R_PD, respectively, after an intermediate temperature cleaning at 50°C, indicating that higher enzyme density offers more efficient self-cleaning than the combined effect of enzyme and PNIPAAm at low concentration. The conformational volume phase transition of PNIPAAm did not affect the stability of immobilized trypsin on membrane surface. Such novel surface engineering design offer a promising route to severe surface-protein contamination remediation in food and wastewater applications.

Interior permanent magnet motors (IPMSMs) are extensively used as traction motors today because of their exceptional torque and power density, and wide constant power operating range. Under real-world usage, an IPMSM rotor undergoes varying electromagnetic, thermal, and mechanical loads. Under such conditions, fatigue life-based design criteria should be utilized over stress-based design criteria to ensure the structural integrity of the rotor. Moreover, the driving dynamics can change the rotor temperature continuously, which affects the electromagnetic, mechanical, and fatigue properties of rotor material. This paper proposes a robust thermo-mechanical rotor fatigue simulation workflow considering the significant loads acting on an IPMSM rotor and the temperature variation throughout a drive cycle. It discusses an accelerated fatigue life estimation approach based on peak valley extraction to reduce the simulation time significantly for stress and fatigue analysis. Then, it presents a method for stress-life curve generation for a variable loading. It also presents a sensitivity study with a median S-N curve, and a 90%-reliability 95%-confidence (R90C95) S-N curve.

(1) Background: This article presents a study that aims to provide a precise understanding of the temperature distribution within a Whole-Body Cryostimulation (WBC) chamber, whether it is empty or occupied by one or several individuals.; (2) Methods: The study employs a mixed numerical and experimental approach, utilizing simplified Computational Fluid Dynamics (CFD) simulations and an experimental analysis that employs thermocouples to determine the 3D thermal field in actual conditions.; (3) Results: The results reveal a non-negligible temperature difference between the setpoint and actual temperature in the middle of the cryochamber. Furthermore, it is shown that the presence of individuals inside the chamber results in both an average temperature rise and a more heterogeneous thermal behavior, which appear to be associated with the number of individuals present.; (4) Conclusions: The findings of this study emphasize the need for further research to establish temperature guidelines and standardize measurement methods for effective WBC treatment.

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

The aim of this review was to provide an update on the potential of cell therapies to restore or replace damaged and/or lost cells in retinal degenerative and optic nerve diseases, describing the available cell sources and the challenges involved in such treatments when these techniques are applied in real clinical practice. Sources include human fetal retinal stem cells, allogenic cadaveric human cells, adult hippocampal neural stem cells, human CNS stem cells, ciliary pigmented epithelial cells, limbal stem cells, retinal progenitor cells (RPCs), human pluripotent stem cells (PSCs) (including both human embryonic stem cells (ESCs) and human induced pluripotent stem cells (iPSCs)) and mesenchymal stem cells (MSCs). Of these, RPCs, PSCs and MSCs have already entered early-stage clinical trials since they can all differentiate into RPE, photoreceptors or ganglion cells, and have demonstrated safety, while showing some indicators of efficacy. Stem/progenitor cell therapies for retinal diseases still have some drawbacks, such as the inhibition of proliferation and/or differentiation in vitro (with the exception of RPE) and the limited long-term survival and functioning of grafts in vivo. Some other issues remain to be solved concerning the clinical translation of cell-based therapy, including (1) the ability to enrich for specific retinal subtypes; (2) cell survival; (3) cell delivery, which may need to incorporate a scaffold to induce correct cell polarization, which increases the size of the retinotomy in surgery and, therefore, the chance of severe complications; (4) the need to induce retinal detachment to perform the subretinal placement of the transplanted cell; and (5) the evaluation of the risk of tumor formation caused by the undifferentiated stem cells and prolific progenitor cells. Despite these challenges, stem/progenitor cells represent the most promising strategy for retinal and optic nerve disease treatment in the near future, and therapeutics assisted by gene techniques, neuroprotective compounds and artificial devices can be applied to fulfil clinical needs.

Fiber optic sensors cannot measure damage; for getting information about damage from strain measurements, additional strategies are needed, and several alternatives have been proposed. This paper discuss two independent concepts: the first one is based on detecting the new strains appearing around a damage spot; the structure does not need to be under loads; the technique is very robust, damage detectability is high, but it requires sensors to be located very close to the damage, so it is a local technique. The second approach offers a wider coverage of the structure, it is based on identifying the changes caused by the damage on the strains field in the whole structure for similar external loads. Damage location does not need to be known a priori, detectability is dependent upon the sensors network density, damage size and the external loads. Examples of application to real structures are given.

The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

Background: Post-acute sequelae of SARS-CoV-2 infection (PASC) is a complicated disease that affects millions of people all over the world. Previous studies have shown that PASC impacts 10% of SARS-CoV-2 infected patients of which 50-70% are hospitalized. It has also been shown that 10-12% of those vaccinated against COVID-19 were affected with PASC and its complications. The severity and the later development of PASC symptoms is positively associated with the early intensity of the infection. Results: The generated health complications caused by PASC involve a vast variety of organ systems. Patients affected by PASC have been diagnosed with neuropsychiatric and neurological symptoms. Cardiovascular system also has been involved and several diseases such as myocarditis, pericarditis, and coronary artery diseases were reported. Chronic hematological problems such as thrombotic endothelialitis and hypercoagulability were described as a condition that could increase the risk of clotting disorders and coagulopathy in PASC patients. Chest pain, breathlessness, and cough in PASC patients were associated with respiratory system in long COVID-19 causing respiratory distress syndrome. The observed immune complications were notable, involving several diseases. Renal system also was impacted and result in raising the risk of diseases such as thrombotic issues, fibrosis, and sepsis. Endocrine gland malfunction can lead to diabetes, thyroiditis, and male infertility. Symptoms such as diarrhea, nausea, loss of appetite and taste were also among reported observations due to several gastrointestinal disorders. Skin abnormalities might be an indication of infection and long-term implications such as persistent cutaneous complaints were linked to PASC. Conclusions: Long COVID is a multidimensional syndrome with considerable public health implications, affecting several physiological systems and demanding thorough medical therapy as well as more study to address its underlying causes and long-term effects.

A formulation of nonequilibrium thermo field dynamics has been performed using the nonequilibrium statistical operator method by D.N. Zubarev. Generalized transfer equations for a consistent description of kinetics and hydrodynamics of the dense quantum-field system with strongly coupled states are derived.

Antler is the fastest growing tissue. Because is based on proto-oncogenes, to avoid the risk of cancer, antlers evolved strong anticancer mechanisms, and thus its extract (DVA) is effective also against the few human tumours studied so far. We assessed whether DVA is a general anticancer compound testing direct effects in cells of different tumours: glioblastoma (GBM), colorectal and breast cancer, and leukaemia. DVA reduced viability of tumour but not healthy cells. Mobility decreased at least at the longest test (72 h). Intraperitoneal/oral 200 mg DVA/kg administration in GBM xenograft mice for 28 d reduced tumour weight 66.3% and 61.4% respectively, and also spleen weight. In addition, tumours treated with DVA showed symptoms of liquefactive necrosis. Serum cytokines showed DVA up-regulated factors related with tumour fighting and down-regulated those related with inducing immune tolerance to the tumour. DVA shows general anticancer effects in the lines tested and, in GBM mice, also strong indirect effects apparently mediated by the immune system.

This article delves into the complex landscape of Bitcoin halving events, analyzing the historical context and implications of these pivotal occurrences within the cryptocurrency ecosystem and on its sustainability within the landscape of financial technologies. Through an examination of past halving events in 2012, 2016, and 2020, this study meticulously scrutinizes the conditions and prices of Bitcoin before and after each halving. By synthesizing data and trends from previous events, this article aims to uncover patterns and insights that illuminate the impact of Bitcoin halving on market dynamics and sustainability, movement of the price level, reached peaks and price troughs. Furthermore, this research presents a comparative analysis of past halving events, drawing parallels and distinctions to elucidate the evolving nature of Bitcoin's price movements and market sentiment surrounding these milestone events. Looking towards the future, this study estimates predictions and expectations for the upcoming Bitcoin halving. By unraveling the intricate relationship between Bitcoin halving events and market behavior, this article seeks to provide a comprehensive understanding of the broader implications for Bitcoin's trajectory and the evolving landscape of the cryptocurrency market and its sustainability.

This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.

Background Most of the Leber hereditary optic neuropathy (LHON) cases are bilateral and sequential, how-ever there are rare unilateral examples, or those in which the delay of onset of vision loss between one and the other eye is longer. In the case of presumed childhood amblyopia in one eye, the vision loss in the good eye may be the only symptom of bilateral disease, that was unnoticed in previ-ously amblyopic eye, or a preexisting episode of LHON on the “amblyopic” eye. Clinical decision in such cases may be difficult and suggestive for other forms of atypical optic neuropathy until confirmed by genetic testing. Case series We present three genetically confirmed (MT-ND1:m.3700G>A, MT-ND6:m14484 T>C, and MT-ND4:m.11778G>A) patients with subacute vision loss in previously good eye with the other eye believed to be amblyopic from the childhood, and their features different of what would be expected in true amblyopia. In all, electrophysiology testing showed bilaterally reduced ampli-tude of PERG with low VEP P100 wave amplitudes and prolonged peak time in both eyes, also unusual for amblyopia. During the follow-up, pallor of the optic discs progressed in all eyes. Significant thinning of the retinal nerve fiber layer around the optic disc (pRNFL) and ganglion cell complex (GCC) in the macular region was present. All three patients had peculiar history. First patient was treated for presumed hyperopic amblyopia that did not improve since child-hood and experienced visual loss on the good eye at the age of 17 and was negative for the three typical LHON mutations. Extended testing confirmed atypical pathogenic variant MT-ND1:m.3700G>A in homoplasmy. The second patient with presumed strabismic amblyopia had unusual presentation of vision loss only at the age of 61 and after exclusion of other causes, typical MT-ND4:m.11778G>A pathogenic variant was found in homoplasmy. The third case was peculiar as he had presumed strabismic amblyopia since childhood and had some degree of disc pallor in the amblyopic eye upon presenting with loss of vision on the good eye at the age of 21 and typical pathogenic variant m14484 T>C, p.Met64Val was subsequently confirmed. However, one year after the disease onset, he started to experience significant spontaneous functional im-provement in the non-amblyopic up to 1.0 Snellen, whilst improvement in the presumed amblyop-ic eye was modest, suggesting preexisting amblyopia. This interestingly extensive improvement was carefully followed by electrophysiology as well as visual acuity and fields. Conclusion This report shows three different scenarios of presentation of LHON in patients with presumed uniocular amblyopia from childhood. In such cases, the diagnosis may be difficult and detailed structural and functional evaluation of the optic nerve head is necessary to assess whether earlier LHON episode was misdiagnosed as amblyopia or whether LHON presented bilaterally on both eyes whilst only being noticed in the previously good eye.

Optical biopsy describes a range of medical procedures in which light is used to investigate disease in the body, often in hard-to-reach regions via optical fibres. Optical biopsies can reveal a multitude of diagnostic information to aid therapeutic diagnosis and treatment with higher specificity and shorter delay than traditional surgical techniques. One specific type of optical biopsy relies on Raman spectroscopy to differentiate tissue types at the molecular level and has been used successfully to stage cancer. However, complex micro-optical systems are usually needed at the distal-end to optimise the signal-to-noise properties of the Raman signal collected. Manufacturing these devices remains a critical challenge, particularly in a way suitable for large scale adoption. In this paper, we describe a novel fibre-fed micro-optic system designed for efficient signal delivery and collection during a Raman spectroscopy based optical biopsy. Crucially, we fabricate the device using a direct-laser-writing technique known as ultrafast laser assisted etching which is scalable and allows components to be aligned passively. The Raman probe has a sub-millimetre diameter and offers confocal signal collection with 71.3 ± 1.5% collection efficiency over a 0.8 numerical aperture. Proof of concept spectral measurements were performed on mouse intestinal tissue and compared with results obtained using a commercial Raman microscope.

In this paper, a novel pendulum-type accelerometer based on hetero-core fiber optics has been proposed for structural health monitoring targeting large-scale civil infrastructures. Vibration measurement is a non-destructive method for diagnosing the failure of structures by assessing natural frequencies and other vibration patterns. The hetero-core fiber optic sensor utilized in the proposed accelerometer can serve as a displacement sensor with robustness to temperature changes in addition to immunity to electromagnetic interference and chemical corrosions. Thus the hetero-core sensor inside the accelerometer measures applied acceleration by detecting the rotation of an internal pendulum. A series of experiments showed that the hetero-core fiber sensor linearly responded to the rotation angle of the pendulum ranging within ±5°, and furthermore the proposed accelerometer could reproduce the waveform of input vibration in a frequency band of several Hz order.

A novel fiber optic sensing technology for high frequency dynamics detection is proposed in this paper, specifically tailored for structural health monitoring applications based on strain wave analysis, including both passive impact identification and active Lamb wave monitoring. The sensing solution relies on a fiber optic-based interferometric architecture associated to an innovative coherent detection scheme, which retrieves in a completely passive way the high-frequency phase information of the received optical signal. The optical fiber can be arranged into different configurations in order to meet the requirement of the specific application, the sensor sensitivity being maximized while still ensuring a limited gauge length if a local measure is required. For the active Lamb wave monitoring, this results in a sensing fiber arranged in multiple loops glued on an aluminum thin panel in order to increase the phase signal relative only to the sensing points of interest. Instead, for passive impact identification, the sensitivity is simply increased by exploiting a longer gauge length glued to the structure. The fiber optic coherent (FOC) sensor detects the strain waves emitted by a piezoelectric transducer placed on the aluminum panel or generated by an impulse hammer, respectively. The FOC sensor measurements have been compared with both a numerical model based on Finite Elements and traditional piezoelectric sensors, confirming a very good agreement between experimental and simulated results for both the active and passive impact monitoring scenarios.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

BACKGROUND AND OBJECTIVE: The use of biomass for cooking carries significant health implications and can lead to adverse environmental issues such as deforestation, greenhouse gas emissions, and erosion. Despite these concerns, there is a lack of information about the nature and extent of cooking emissions in many developing countries. To address this gap, a study was conducted to assess cooking emission levels and their associated health effects among households in Dodoma City, Tanzania. METHODS: A descriptive cross-sectional design was conducted, involving 285 households in the peri-urban area of Dodoma City, Tanzania. A combination of questionnaires, observational checklists, and sampling devices (Aeroqual series 500 for Carbon Monoxide and Temptop PMD 351 for Particulate Matters) were employed for data collection, adhering to established protocols. Additionally, lung function tests were conducted with consent from the primary household cooks. Collected data were entered into an Excel spreadsheet and analyzed using STATA 17 software. FINDINGS: Out of 285 participants, 74.7% predominantly use charcoal for cooking, with 68.4% having outdoor kitchen setups. Significant differences in pollutant concentrations were observed across various fuel types (P=0.0001), with firewood emitting higher levels of particulate matter and carbon monoxide. Carbon monoxide concentrations during cooking were 6 times higher for firewood, 5 times higher for charcoal-gas, and 3 times higher for charcoal compared to WHO daily average limits. Additionally, a positive correlation between pollutant concentrations was noted (P-value = 0.0000). Lung problems 17.8% followed by eye irritation 15.7% were mentioned by those who claimed to know the health effects associated with cooking emissions. In addition, the spirometry test indicated that the majority of the participants had % predicted >80 while only 19% had % predicted below 50. CONCLUSION: Charcoal and firewood remain the primary cooking fuels in the study area despite their significant negative impacts. Our findings highlight a lack of awareness among community members regarding the health effects of biomass cooking emissions and insufficient guidance on constructing healthy kitchens. To address this, enforcing building standards, raising health awareness, and ensuring affordable access to modern fuels are crucial steps. These measures are essential for promoting healthier cooking practices and mitigating the adverse effects on households.

Bone fractures are very common in the geriatric population and poses a great economic burden worldwide. While traditional methods for repairing bone defects have primarily been autografts, there are several drawbacks limiting its use. Bone graft substitutes have been used as alternative strategies to improve bone healing. However, there remains several impediments to achieving the desired healing outcomes. Injectable hydrogels have become attractive scaffold materials for bone regeneration given their high performance in filling irregularly sized bone defects, ability to encapsulate cells and bioactive molecules, and mimic the native ECM of bone. We investigated the use of an injectable chitosan-based hydrogel scaffold to promote differentiation of preosteoblasts in vitro. The hydrogels were characterized by evaluating cell homogeneity, cell viability, rheological and mechanical properties, and differentiation ability of preosteoblasts in hydrogel scaffolds. Cell-laden hydrogel scaffolds exhibited shear thinning behavior and the ability to maintain shape fidelity after injection. The CNC-CS hydrogels exhibited higher mechanical strength and significantly upregulated the osteogenic activity and differentiation of preosteoblasts as shown by ALP activity assays and histological analysis of hydrogel scaffolds. These results suggest that this injectable hydrogel is suitable for cell survival, can promote osteogenic differentiation of preosteoblasts, and structurally support new bone growth.

This study focuses on the potential medicinal properties of Campsis radicans L. extracts and its aim is to investigate the antioxidant and antiproliferative effects of these extracts on the human colon adenocarcinoma cell line (HT-29). Cytotoxic activity in the HT-29 cell line was evaluated, and the 3-dimensional structures of phenolic compounds were obtained using the GC-MS method. Docking simulations were performed with AutoDock Vina, targeting proteins that are crucial in the apoptotic pathway (Bax, Bcl-2, and Caspase-3). Drug similarities and ADMET estimates of the phenolic compounds were obtained from databases. The highest antioxidant activity of Campsis radicans L. plant was observed in ethanol and water extracts, with notable inhibition capacities. While the total phenolic content was highest in ethanol, water, and ether extracts respectively the total flavonoid content was highest in ethanol, then ether, and water extracts. Certain elements were undetectable in mineral determination, and others exceeded the toxic doses for plants. The water extract exhibited dose-dependent cytotoxic activity in the HT-29 cell line, with an IC50 value of 4.47 mg/mL. Molecular docking results revealed the binding of phenolic molecules to the active sites of apoptotic pathway proteins. The findings suggest that Campsis radicans L. plant possesses cytotoxic properties, significant phenolic and flavonoid content, and a high antioxidant capacity. These properties make it a potential candidate for treatment use, emphasizing its potential therapeutic value in the HT-29 cell line. Further research and exploration on the identified phenolic compounds could contribute to the development of novel therapeutic agents.

Theoretical studies on the generation of nondiffracting and nondispersive light pulses and their experimental implementation are one of the renowned problems within electromagnetics. Current technologies enable creation of short-duration pulses of a few cycles with high power and fluency. An application of these techniques to the field of nondiffracting and nondispersive pulses requires a proper mathematical description of highly focused vector pulses. In this work, we study vector optical bullets in a dielectric medium with different polarization structures: linear, azimuthal, and radial. We report the differences caused by the vector model compared to the scalar model. We analyze effects caused by superluminal, subluminal, or even negative group velocity on properties of vector optical bullets inside a dielectric material.

This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

Mortarless refractory masonry structures are widely used in the steel industry for the linings of many high-temperature industrial applications including steel ladle. The design and the optimization of these components require accurate numerical models that consider the presence of joints as well as joints closure and opening due to cyclic heating and cooling. The present work reports on the formulation, numerical implementation, validation, and application of homogenized numerical models for simulation of refractory masonry structures with dry joints. The validated constitutive model has been used to simulate a steel ladle and to analyze its transient thermomechanical behavior during a typical thermal cycle of steel ladle. 3D solution domain, enhanced thermal and mechanical boundary conditions have been used. Parametric studies to investigate the impact of joints thickness on the thermomechanical response of the ladle have been carried out. The results clearly demonstrate that the thermomechanical behavior of mortarless masonry is orthotropic nonlinear due to gradual closure and reopening of joints with the increase and decrease of temperature. Also, resulting thermal stresses increase with the increase of temperature and decrease with the increase of joints thickness.

Salmonella infections can lead to intestinal inflammation and metabolic disorders in birds. However, whether ARA metabolism is involved in Salmonella-induced intestinal inflammation remains unclear. This experiment investigated the changes in cecal flora and arachidonic acid (ARA) metabolism in Hainan Wenchang chickens infected with S. Typhimurium using 16s rDNA sequencing and targeted metabolomics. The results showed that the levels of ARA metabolites were increased in the cecum tissue of Wenchang chickens after infection with S. Typhimurium, including prostaglandin E2, prostaglandin F2α, lipoxin A4, ±8(9)-EET, ±11(12)-EET, and ±8,9-DiHETrE. The content of key enzymes for ARA production and metabolism (PLA2 and COX-2) in chicken cecum tissues was increased after S. Typhimurium infection. The relative mRNA levels of inflammatory factors were also increased after infection, including IFN-γ, TGF-β1, IL-4, and IL-6. In HD11 cells, the use of a cyclooxygenase (COX) inhibitor reduced the increased levels of COX-2 and PGF2α induced by S. Typhimurium infection and effectively reduced the inflammatory response. In addition, the number of beneficial genera (e.g., Bifidobacterium, Lactobacillus, and Odorobacterium) in the cecum of Wenchang chickens was significantly reduced after infection with S. Typhimurium. In this study, we revealed the structure of the cecal flora of Wenchang chickens infected with S. Typhimurium and demonstrated that S. Typhimurium can mediate the onset and development of intestinal inflammation through the activation of the metabolic pathway of ARA cyclooxygenase in Wenchang chickens. The results can provide data support and theoretical support for the prevention and control of avian salmonellosis.

Lactoperoxidase (LP) is an important enzyme of the salivary and mammary glands. It has been proven to increase the shelf life of raw milk by inhibiting the growth of bacteria, especially Listeria monocytogenes, Escherichia coli, Staphylococcus aureus, and Pseudomonas spp. The aim of this work was to verify the use of LP to extend the shelf life of meat products. In vitro experiments showed inhibitory effects against selected bacteria (Listeria innocua (ATCC 33090), Staphylococcus saprophyticus (CP054440.1), and Pseudomonas fluorescens (ATCC 13525) due to prolongation of the lag phase of growth curves. A lower increase in viable counts (P &lt; 0.05) was also found by testing the pork cubes surface treated with LP solution (5%) + L. innocua and stored for 7 days at 15 °C. LP has also been studied at concentrations of 0.25 and 0.50% in meat products (pork ham and pâté) during refrigerated storage (4 °C for 28 days). Lower viable counts were observed throughout the storage experiment, especially for 0.50% LP (P &lt; 0.05). Meat products containing LP also showed lower levels of oxidation (MAD) (P &lt; 0.05). According to these results, LP could extend the shelf life of a wider range of products.

For a fiber optic gyroscope, thermal deformation of the fiber coil can introduce additional ther-mal-induced phase errors, commonly referred to as thermal errors. Thermal error compensation techniques are effective means of addressing this issue. The principle behind these techniques involves real-time sensing of thermal errors and correcting them within the output signal. Since it is challenging to directly separate thermal errors from the output signal of the fiber optic gyro-scope, it is necessary to predict thermal errors based on temperature. To establish a mathematical model between temperature and thermal errors, this paper measured synchronized data of phase errors and angular velocity for the fiber coil under different temperature conditions and aimed to model it using data-driven methods. Due to the difficulty of conducting tests and the limited number of data samples, an algorithm called TD-model modeling is proposed to address the issue of overfitting, which can reduce the model's generalization ability. First, a theoretical analysis of the phase errors caused by thermal deformation of the fiber coil is performed. Subsequently, the critical parameters, such as the thermal expansion coefficient, are determined, and a theoretical model is established. Finally, the theoretical analysis model is incorporated as a regularization term and combined with the test data to jointly participate in the regression of model coefficients. Through experimental comparative analysis, it is shown that, relative to ordinary regression models, the TD-model effectively mitigates overfitting caused by the limited number of samples, leading to a 58% improvement in predictive accuracy.

Chemical pollution poses a significant threat to human health, with detrimental effects on various physiological systems, including the respiratory, cardiovascular, mental, and perinatal domains. While the impact of pollution on these systems has been extensively studied, the intricate relationship between chemical pollution and immunity remains a critical area of investigation. The focus of this study is to elucidate the relationship between chemical pollution and human immunity. To accomplish this task, this study presents a comprehensive review that encompasses in vitro, ex vivo, and in vivo studies, shedding light on the ways in which chemical pollution can modulate human immunity. Our aim is to unveil the complex mechanisms by which environmental contaminants compromise the delicate balance of the body's defence systems going beyond the well-established associations with defence system delving into the less-explored link between chemical exposure and various immune disorders, adding urgency to our understanding of the underlying mechanisms and their implications for public health.

Background Ultrasonographic measurement of the optic nerve sheath diameter (ONSD) is helpful in the assessment of intracranial pressure. The aim of this study was to determine whether the Trendelenburg position during laparoscopic urological surgery changed the ONSD and whether changes correlated with postoperative complications. Methods In this prospective study, we measured ONSD before patients were placed in the Trendelenburg position. Then the Trendelenburg position was established by tilting the operating table to 20-25 degrees. After surgery, the patients were placed in a horizontal position, and the second measurement of ONSD was obtained. Results The study included 69 patients. The average preoperative ONSD in the right eye was 5.8 ± 0.7 mm and 5.8 ± 0.8 mm in the left eye. The average postoperative ONSD in the right eye was 6.6 ± 0.8 mm and 6.6 ± 0.7 mm in the left eye. The differences between postoperative and preoperative values in the right and left eyes were statistically significant (p <0.000001). ONSD increases above the norm did not correlate with the incidence of postoperative nausea (p = 0.94), delirium (p = 0.81), or the time to patient awakening (p = 0.29). Conclusion ONSD increased in patients who underwent surgical procedures performed in the Trendelenburg position, but the increase did not correlate with postoperative complications.

This study investigated the evolution of density, gas permeability and thermal conductivity of sugar maple wood during the thermo-hygro-mechanical densification process. The results suggested that the oven-dry average density of densified samples was significantly higher than that of the control samples. However, the oven-dry density did not show a linear increase with the decrease of wood samples thickness. The radial intrinsic gas permeability of the control samples was 5 to 40 times higher than that of densified samples, which indicated that the void volume of wood was reduced notably after the densification process. The thermal conductivity increased by 0.5 - 1.5% per percent increase of moisture content for densified samples. The thermal conductivity of densified wood was lower than that of the control samples. The densification time had significant effects on the oven-dry density and gas permeability. Both the densification time and the moisture content had significant effects on thermal conductivity, but their interaction effect was not significant.

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode~2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

Pregnancy is a complex biological process which is associated with significant metabolic and hemodynamic changes of the maternal body which allow a normal fetal growth. The inability to adapt to these changes can affect the cardiovascular health. During pregnancy, women may experience mood swings, anxiety and emotional ambivalence. These symptoms can lead to stress and have a negative impact on the mental well-being of expectant mothers. It is crucial to know the aspects that can influence the development of cardiovascular problems among pregnant women in order to manage these cases properly. The current narrative review explores and summarizes the evidence regarding the impact of stress and anxiety on cardiovascular health in pregnant women. Understanding the physiological adaptations that the body undergoes throughout pregnancy is crucial for educating and supporting individuals as well as healthcare professionals. This enables them to recognize any risk factors or pathological conditions that may exacerbate pregnant women's health. In order to reduce maternal morbidity and mortality from cardiovascular disease, a psychological and cardiovascular risk factor screening that is done either before or during pregnancy may be able to identify situations that call for particular medical and/or psychological therapies.

This paper introduces a closed-loop control strategy for maintaining consistency of liquid temperature in commercial Drop on Demand (DoD) inkjet printing. No additional sensors or additional actuators are installed in the printhead while achieving the consistency in liquid temperature. To this end, this paper presents a novel in situ sensing-actuation policy at every individual liquid-nozzle, where the jetting mechanism has three distinct roles. It is used for jetting liquid droplet onto the print media based on the print-job. It is used as a soft sensor to estimate the real-time liquid temperature of the jetting nozzle. While not jetting liquid, it is used as a heating actuator to minimize the gradient of liquid temperature among nozzles. The soft sensing based in situ controller is implemented in an experimentally validated digital twin that models the thermo-fluidic processes of the printhead. The digital twin is scalable and flexible to incorporate an arbitrary number of liquid-nozzles, making the control strategy applicable for future designs of the printhead.

Kisspeptin, a key neuropeptide derived from the KISS1 gene, is renowned for its critical role in regulating the hypothalamic-pituitary-gonadal axis and reproductive hormone secretion. Beyond its primary function in reproductive biology, emerging research has illuminated its influence in various cancers, mediating significant effects through its interaction with the G-protein coupled receptor, Kisspeptin receptor. This interaction has been implicated in modulating cellular pro-cesses such as proliferation and metastasis, making it a potential target for therapeutic interven-tion. Our study initially screened ten kisspeptin-10 analogs through cytotoxic effects of kisspep-tin-10 (KP10) and its analogs in several cancer types, including cervical, prostate, breast, and gastric cancers, with a particular focus on cervical cancer where the most profound effects were observed. Further exploration using kinase array assays revealed that these analogs specifically alter key kinases involved in cancer progression. Migration assays demonstrated a substantial decrease in cell motility, and Bioluminiscence Resonance Energy Transfer assays confirmed these analogs strong interactions with the kisspeptin receptor. Overall, our results indicate that these KP10 analogs not only hinder cervical cancer cell proliferation but also curtail migration through targeted modulation of kinase signaling, suggesting their potential as therapeutic ayfgents in managing cervical cancer progression. This comprehensive approach underscores the therapeutic promise of exploiting kisspeptin signaling in cancer treatment strategies.

The electronic structure of 7/9-AGNR superlattices with up to eight unit cells has been studied by means of state of the art Density Functional Theory (DFT) and also by two model Hamiltonians, the first one including only local interactions (Hubbard model, Hu) while the second one is extended to allow long-range Coulomb interactions (Pariser, Parr and Pople model, PPP). Both are solved within mean field approximation. At this approximation level, our calculations show that 7/9 interfaces are better described by spin non-polarized solutions than by spin-polarized wavefunctions. Consequently, both Hu and PPP Hamiltonians lead to electronic structures characterized by a gap at the Fermi level that diminishes as the size of the system increases. DFT results show similar trends although a detailed analysis of the density of states around the Fermi level shows quantitative differences with both Hu and PPP models. Before improving model Hamiltonians, we interpret the electronic structure obtained by DFT in terms of bands of topological states: topological states localized at the system edges and extended bulk topological states which interact between them due to the long-range Coulomb terms of Hamiltonian. After careful analysis of the interaction among topological sates, we find that the discrepancy between ab initio and model Hamiltonians can be resolved considering a screened long-range interaction that is implemented adding an exponential cutoff to the interaction term of PPP model. In this way, an adjusted cutoff distance λ = 2 allows a good recovery of DFT results. In view of this, we conclude that the correct description of the density of states around the Fermi level (Dirac point) needs the inclusion of long-range interactions well beyond Hubbard model but not completely unscreened as is the case for the PPP model.

The impact of the agriculture net carbon effect is crucial for climate change mitigation, yet research on this topic in China is currently insufficient. In this study, the carbon balance ratio (CBR) is used to characterise the net carbon effect of agriculture, and the spatial Durbin model and threshold regression model were used to empirically analyse the CBR with a sample of 30 provincial-level regions in China from 2004 to 2019. The aim was to investigate the mechanism of the influence of the land management scale (SCALE) of farming on the CBR. The results of the study indicate that national farming generally has a net sink effect, with large changes in interannual fluctuations; the expansion of SCALE has an obvious role in increasing sinks and reducing emissions, and has a positive spatial spillover effect on CBR, with significant spatial heterogeneity. Furthermore, as the SCALE expands, the direction of the influence of rural residents’ income and education level on CBR changes in the opposite direction, showing a significant non-linear relationship characteristic. However, in most areas, the SCALE threshold has not yet been reached, suggesting that the improvement in education levels can still offset the negative impact of economic income growth in the short term. The study recommends paying attention to the role of farmers’ human capital, changing production methods, and implementing carbon peaking and carbon neutrality goals to enhance the net sink effect of the farming industry, which would be achieved by increasing land management scale.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

The agricultural industry relies on physical fences to manage livestock. However, physical fences present some practical, financial, and ecological problems, that partly may be solved by virtual fencing. However, it is necessary for the livestock to be adapted to virtual fencing. This study aims to identify if adaptation to virtual fence can be improved through social facilitation between experienced cattle and the remaining herd. Moreover, which of the two different learning processes, a gradual or instant introduction to virtual fence is the most effective in associating warnings with impulses. Three pastures containing Angus (Bos taurus) will be used to examine these investigations; A, B and C. All investigations are conducted on the Danish Island of Fanø. Three methods of learning process were used, one gradual and two instant introductions to the virtual fence. The investigations had varying amounts of experienced cattle. Impulses and warnings were recorded during a learning period and the following observation period. To quantify if the cattle adapt to the warnings, impulses per warning are used. There was no evidence of improvement with the presence of experienced cattle for any pastures, indicating no social facilitation. Gradual introduction was found to be more beneficial than instant introduction. More standardized tests are necessary to discover the full effect of experienced cattle.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (&gt;0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (&lt;0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size &gt;100 μm, and soil structure was the most stable.

A major advance of drug discovery and targeted therapy directed to cancer cells may be achieved by exploitation and immunomodulation of their unique biological property. This re-view summarizes our efforts to develop novel chemo-thermo-immuno-therapy (CTI therapy) by conjugating a melanogenesis substrate, N-propionyl cysteaminylphenol (NPrCAP: amine analog of tyrosine), with magnetite nanoparticles (MNP). In our approach, NPrCAP provides a unique drug delivery system (DDS) because of its selective incorporation into melanoma cells. It also functions as a melanoma-targeted therapeutic drug because of its production of highly reactive free radicals (melanoma-targeted chemotherapy). Moreover, utilization of MNP is a platform to develop thermo-immunotherapy because of heat shock protein (HSP) generation upon exposure to an alternating magnetic field (AMF). The feasibility of our approach was successfully shown in experimental in vivo and in vitro mouse melanoma models and in preliminary clinical trials to a limited number of advanced melanoma patients.

Special preparation of SBA-15 materials has been carried out for creating adsorbents exhibiting an enhanced and selective adsorption toward CO2. This creation starts from an adequate conditioning of the silica surface, via a thermo-alkaline treatment to increase the population of silanol species on it. CO2 adsorption is only reasonably achieved when the SiO2 surface becomes aminated after put in contact with a solution of an amino alkoxide compound in the right solvent. Unfunctionalized and amine-functionalized substrates were characterized through X-ray diffraction, N2 sorption, Raman spectroscopy, electron microscopy, 29Si solid-state NMR, and NH3 thermal programmed desorption. These analyses proved that the thermo-alkaline procedure desilicates the substrate and eliminates the micropores (without affecting the SBA-15 capillaries), present in the original solid. NMR analysis confirms that the hydroxylated solid anchors more amino functionalizing molecules than the unhydroxylated material. The SBA-15 sample subjected to hydroxylation and amino- functionalization displays a high enthalpy of interaction, a reason why this solid is suitable for a strong deposition of CO2 but with the possibility of observing a low-pressure hysteresis phenomenon. Contrastingly, CH4 adsorption on amino-functionalized, hydroxylated SBA-15 substrates becomes almost 5 times lesser than the CO2 one, thus giving proof of their selectivity toward CO2.

Abstract: In this comprehensive review, we delve into the significance of the mul-timodal imaging in diagnosing and managing of complications of congenital optic nerve anomalies.. While the Fundus examination is the gold standard tool in diagnosisc of these pathologies, SD OCT and OCTA could shed a light in the pathogenesis, and treatment. Moreover , this review seeks to offer a comprehensive insight into a multimodal approach of these rare congenital pathologies. In conclusion, congenital anomalies of the optic nerve represent a major challenge for ophthalmologists Further research could be clarify the pathophysiology of these diseases and define a correct and specific treatment approach. Keywords: keyword 1; ODC, ODP, MGS, OCT; OCTA, Multimodal imaging.

In areas where conventional fundus cameras are logistically unaffordable, the smartphone-based approach is considered as a promising future of glaucoma screening due to their affordability and ease-of-use. Optic disc localization is a critical stage during glaucoma screenings. For fundus images captured with standard fundus cameras, the majority of the models available out there can locate the optic disc with satisfactory performance. However, for images that are captured with smartphone-based fundus cameras, the inherent noise and lower quality of the fundus image makes it difficult for models to detect the optic disc region. In this study, we have proposed to utilize YOLOv8n for optic disc localization due to the model’s cutting-edge performance in diverse tasks and its lightweight nature. We have used a public dataset which has 2000 low quality fundus images that are captured using a smartphone-based fundoscopy device. From these, 60% of the data was used for fine-tuning the model, and 25% for testing. By using a confidence of 50% set as threshold, the model was able to detect the optic disc successfully on over 97% of test images with intersection over union of above 0.85. These results highlight the potential of the lightweight YOLOv8n model for deployment on resource-constrained environments, offering a promising performance on accurately localizing the OD and enhancing the feasibility of affordable glaucoma screening on smartphones.

Turbidity is an important water quality parameter, especially for drinking water. The ability to actively monitor the turbidity level in Drinking Water Distribution Systems is of critical importance to the safety and wellbeing of the public. Traditional turbidity monitoring methods involve manual collection of water samples at set locations and times followed by laboratory analysis, which are labor intensive and time consuming. Fiber-optic measurement permits real-time, in-situ turbidity monitoring. But the current technology is based on plastic fibers, which suffer from high optical attenuation and hence are unsuitable for large-scale remote monitoring. In this paper, we report the demonstration of a fiber-optic turbidity sensor based on multi-mode glass fibers. The system uses a single fiber to both deliver laser light into the water sample and collect the back-scattered light for detection. A balanced-detection scheme is utilized to remove the common-mode noise to enhance the turbidity sensitivity. Highly linear turbidity responses are obtained and a turbidity resolution as low as 0.1 NTU is achieved. The test unit is also shown to have excellent reproducibility against repeated measurements and good stability against temperature changes. Turbidity measurement in real environmental matrices such as tap water and pond water is also reported with an assessment of the impact of flow rate. This work demonstrates the feasibility of future large scale distributed fiber-optic turbidity monitoring networks.

Proper Post-Activation Performance Enhancement helps to improve athletic performance. This study aimed to investigate the effects of two different velocity loss (VL), 10%VL and 20%VL, on post-activation performance enhancement (PAPE) in 20m sprint performance among sprint athletes. Twenty-four male sprint athletes (100m sprint time: 10.96±0.15 s) were recruited. A randomized crossover experimental design was used for traditional group (TG), 10%VL, and 20%VL interventions. Sprint tests were conducted at the 4th, 8th, 12th, and 16th minutes after the intervention. Two-way repeated measures ANOVA revealed an interaction effect between group and time on 20m sprint performance (F=2.817, p=0.037, partial η²=0.585). Simple effect analyses showed significant differences compared to baseline at the 4th minute for the 20%VL group (P&lt;0.05). Cohen's d values indicated improvement in 10m sprint times at the 8th minute of the rest interval for all three intervention groups (TG: ES=-0.270, 10%VL: ES=-0.038, 20%VL: ES=-0.279). Improvement in 20m sprint times was observed at the 4th minute for the 20%VL group (ES=-0.296) and at the 16th minute for the 10%VL group (ES=-0.276). Compared to traditional PAPE schemes based on 1RM, PAPE schemes based on velocity loss (20%VL) can better induce PAPE effects in sprint athletes.

Vitamin A, or retinol, is one of the most effective anti-ageing molecules, but it presents issues with photo-sensitivity and irritation. Retinol-like alternatives are emerging, but have so far been less effective. Here, we present a Silibum marianum extract (SME) as a retinol-like ingredient providing both safety and efficacy. SME was compared to the reference compound, retinol, and to the main alternative, bakuchiol. In ex vivo tests, skin explants from a 58-year-old donor were treated with pure retinol (0.1%), bakuchiol (0.2%) or SME (0.8%). After 5 days, collagen and hyaluronic acid levels were analysed. A placebo-controlled study involving 57 volunteers (ages 45-73 years) was also conducted, with products applied twice-daily for 56 days. Results were measured by AEVA-HE and VISA. Levels of collagen III were significantly increased by SME, by 23% and 16% compared to bakuchiol and retinol, respectively. Compared to bakuchiol, SME treatment increased hyaluronic acid production by 36%. In clinical tests, SME had a significantly stronger anti-wrinkle effect than bakuchiol – reducing the number of wrinkles on the forehead by 21%, and their circumference by 17% – producing effects similar to retinol, and better than bakuchiol. In the self-assessment, 43% of volunteers reported discomfort while using retinol, as compared to 0% for the SME formulation. By enhancing levels of collagen III – the youth collagen – and hyaluronic acid in the skin, SME paves the way for the maturation of collagen I fibrils and skin plumping. With its stronger efficacy compared to bakuchiol and enhanced safety profile compared to retinol, SME may be the next-generation of natural alternatives to retinoids.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

Ulcerative colitis (UC) is a chronic inflammatory disease, the incidence of which is increasing worldwide. However, the etiology and pathogenesis of UC remains unclear. The n-butanol extract of pulsatilla decoction (BEPD) of the traditional Chinese medicine herbal formula has been shown to be effective in treating UC. We aimed to explore the molecular mechanism underlying the effects of BEPD on UC, in particular its effects on neutrophil extracellular trap (NET) formation by neutrophils. High-performance liquid chromatography was used to determine the principal compounds of BEPD. UC was induced in mice using dextran sodium sulfate, and mice were treated with 20, 40, or 80 mg/kg BEPD daily for seven days. Colonic inflammation was determined by assessing the disease activity index, histopathology, colonic mucosal damage index, colonic mucosal permeability, and pro- and anti-inflammatory cytokine levels. The infiltration and activation status of neutrophils in the colon were determined by analyzing the levels of chemokine (C-X-C motif) ligand (CXCL)1 and CXCL2, reactive oxygen species, Ly6G, and numerous NET proteins. Our results showed that BEPD improved the disease activity index, histopathology, and colonic mucosal damage index scores of mice with UC, and restored colonic mucosal permeability compared with untreated mice. The expression levels of the pro-inflammatory cytokines interleukin-1β, interleukin-6, and tumor necrosis factor-α in colon tissues were significantly decreased, while the expression levels of anti-inflammatory cytokines in colon tissues were significantly increased, exceeding those of control mice. In addition, BEPD reduce the expression of the neutrophil chemokines CXCL1 and CXCL2 in the colon tissue of mice with UC, reduced neutrophil infiltration, reduced reactive oxygen species levels, and significantly reduced the expression of NET proteins. BEPD also significantly reduced NET formation. The results of this study suggest that BEPD exerts therapeutic effects in a murine model of UC by inhibiting neutrophil infiltration and activation in the colon, as well as by inhibiting the expression of key proteins involved in NET formation and reducing NET formation, thereby alleviating local tissue damage and disease manifestations.

Ultramafic rocks become promising candidates for carbon sequestration by enhanced carbon dioxide (CO2) mineralization strategies due to their highly CO2-reactive mineral composition and its abundant availability. This study reports a mineralogy and microtextures of a representative ultramafic rock from the Ma-Hin Creek in northern Thailand and observes evidence of CO2 mineralization occurring through the interaction between CO2 and the rock with the existence of water under ambient conditions. After sample collection, rock description was determined by optical petrographic analysis. The rock petrography reveals a cumulated wehrlite comprising over 50% olivine and minor amounts of clinopyroxene, plagioclase, and chromian spinel. Approximately 25% of the wehrlite has altered to serpentine and chlorite. A series of CO2 batch experiments were conducted on six different rock sizes at a temperature of 40°C and pressure of 1 atm over five consecutive days. The post-experimental products were dried, weighed, and geochemically analyzed to detect changes in mineral species. Experimental results showed that product weight and the presence of calcite increased with reducing grain size. Additionally, the modal mineralogy of the wehrlite theoretically suggests a potential CO2 uptake of up to 53%, which is higher than the average uptake values of mafic rocks. These findings support the suitable rock investigation approach and the preliminary assessment of carbon mineralization potential, contributing to enhanced rock weathering techniques for CO2 removal that could be adopted by mining and rock supplier industries.

With the rising cost of animal feed protein, finding affordable and effective substitutes is crucial. Walnut kernel cake, a polyphenols, fiber, protein and fat-rich byproduct of walnut oil extraction, has been underexplored as a potential protein replacement in pig feed. In this study, we found that feeding large Diqing Tibetan pigs walnut kernel cake promoted adipose deposition and improved pork quality during pig growth. Transcriptome analysis revealed the upregulation of genes ANGPTL8, CCNP, ETV4, and TRIB3, associated with adipose deposition. Pathway analysis highlighted enrichment in adipose-deposition-related pathways, including PPAR, Insulin, PI3K-Akt, Wnt, and MAPK signaling. Further analysis identified DEGs (differentially expressed genes) positively correlated with adipose-related traits, such as PER2 and PTGES. Single-cell transcriptome data pointed to the specific expression of CD248 and PTGES in adipocyte progenitor/stem cells (APSCs), pivotal for adipocyte differentiation and adipose deposition regulation. This study demonstrates walnut kernel cake's potential to substitute soybean cake in pig feed, providing high-quality protein and promoting adipose deposition. It offers insights into feed protein replacement, human functional food, fat metabolism, and related diseases, with marker genes and pathways supporting pig breeding and pork quality improvement.

The cross-linkable PCL-PEG analogues block-graft copolymer was designed and synthesized, which with the copolymer of the MEO₂MA and OEGMA as graft chains to improve the mPEG-b-PCL-b-mPEG copolymer the aqueous solution properties. And successfully prepared two hydrogels via a copper-catalyzed 1, 3-dipolar azide-alkyne cycloaddition reaction of alkyne-terminated poly[glycidyl methacrylate-co-2-(2-methoxyethoxy) ethyl methacrylate-co-oligo (ethylene glycol) methacrylate] [P(GMA-co-MEO₂MA-co-OEGMA)] with azide end-functionalized PCL-PEG analogues block-graft copolymer, and tetrakis (2-propynyloxymethyl) -methane (TPOM) and with azide end-functionalized PCL-PEG analogues block-graft copolymer. The copolymer's chemical structure was characterized by proton nuclear magnetic resonance spectroscopy and fourier transform infrared spectroscopy. The molecular weights of the copolymers were decided with gel permeation chromatography. The water solubility and temperature sensitivity of the copolymers were studied by taking digital photos and transmittance change measured by UV spectrophotometer at different temperatures. Fluorescence probes, surface tension, dynamic light scattering and transmission electron microscopy were used to analyze the micelles that copolymers self-assembly in aqueous solution. The sol-gel behavior of copolymer solutions at high concentrations was explored by vial inversion experiments. Finally, the network structure of the gels was observed by scanning electron microscopy. These conclusions indicate that these hydrogels are expected to be used as a new material in the field of biomedicine.

Background We aimed to compare the retinal, optic disc vascular density (ODVD) values, and acircularity index (AI) of patients with idiopathic macular telangiectasia type 2 (IMT) and healthy individuals using the optical coherence tomography angiography(OCTA) device. Methods The study included 39 patients with IMT and 37 healthy controls. The OCTA findings of the patients and controls were examined. Results The total, parafoveal and perifoveal vascular density of the superficial capillary plexus, choriocapillaris blood flow, inside-disc ODVD, retinal nerve fiber layer (RNFL), and retinal thicknesses were found to be statistically significantly lower and the foveal avascular zone value was statistically significantly higher in the IMT group compared to the control group (p=0.001, p=0.01, p=0.02, p=0.01, p=0.009, p=0.002, p=0.02, respectively).There was a statistically significant negative correlation between best-corrected visual acuity (BCVA) and AI (p=0.02), a statistically significant positive correlation between peripapillary vascular density and BCVA(p=0.04). Conclusion We consider that the lower retinal, choriocapillaris, and ODVD values, retinal and RNFL thicknesses in the patients with IMT compared to the controls were due to vascular damage, remodeling, fibrosis, proliferation, and Müller cell damage. Ellipsoid zone defect, AI, and peripapillary vascular density are important indicators in the evaluation of visual acuity in these patients.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

Type 2 diabetes mellitus (T2DM), a multifactorial and complicated metabolic disorder, is a growing public health problems. Numerous studies indicated that bioactive compounds from herbal medicine have beneficial effects on T2DM prevention and treatment, owing to their numerous biological properties. Curcumin, the major curcuminoid of turmeric, is one of the most studied bioactive components of herbal supplements, which has a variety of biological activities. Clinical trials and preclinical research have recently produced compelling data to demonstrate the crucial functions of curcumin against T2DM via several routes. Accordingly, this review systematically summarizes the antidiabetic activity of curcumin, along with various mechanisms. Results showed that effectiveness of curcumin on T2DM is due to it being anti-inflammatory, anti-oxidant, anti-hyperglycemic, anti-apoptotic, anti-hyperlipidemia and other activities. In light of these results, curcumin may be a promising prevention/treatment choice for T2DM.

Placental protein 13 (PP13) exhibits a plasma concentration that increases gradually during normal gestation, a process disrupted in preeclampsia, characterized by elevated vascular resistance, re-duced utero-placental blood flow and intrauterine growth restriction. This study investigated PP13’s role in vascular tone regulation and its molecular mechanisms. Uterine and subcutaneous arteries isolated from both pregnant and non-pregnant women were precontracted with the thromboxane analogue U46619, and exposed to PP13 using pressurized myography. The molecular mechanisms were further investigated using specific inhibitors for ni-tric oxide synthase (L-NAME+LNNA at 10-4 M) and guanylate cyclase (ODQ at 10-5 M). Results showed PP13 induced vasodilation in uterine arteries but not in subcutaneous arteries. Ad-ditionally, PP13 counteract U46619-induced vasoconstriction, which is particularly pronounced in pregnancy. Further investigation revealed that PP13's mechanism of action is dependent on activa-tion of the Nitric oxide-cGMP pathway. This study provides novel insights into the vasomodulatory effects of PP13 on human uterine ar-teries, underscoring its potential role in regulating utero-placental blood flow. These findings suggest PP13 may be a promising candidate for improving utero-placental blood flow in condi-tions such as preeclampsia. Further research and clinical studies are warranted to validate PP13's efficacy and safety as a therapeutic agent for managing preeclampsia.

With the aim to improve cladding coating quality and prevent cracking, this paper established an extreme high-speed laser cladding thermo-mechanical coupling simulation model to study the evolution of the temperature field and residual stress distribution. Process parameters that impacted the macroscopic morphology of single-pass coatings were investigated. Numerical calculations and temperature field simulations were performed based on the process parameter data to validate the effect of the temperature gradient and cooling rate on the coating structure and the residual stress distribution. The results showed that a good coating quality could be achieved using a laser power of 2400 W, a cladding rate of 20 m/min, and a powder feeding rate of 20.32 g/min. The coatings’ cross-sectional morphology corresponded well with the temperature distribution predicted by numerical modeling of the melt pool. The microstructure of the molten coatings is affected by the temperature gradient and cooling rate, which vary greatly from the bottom to the middle to the top. Maximum residual stress appears between the bonding region of the coatings and the substrate, and the coatings themselves have significant residual stress in the form of tensile strains that are mostly distributed in the direction of the laser cladding speed.

Transportation contributes significantly to greenhouse gas emissions, with electrification offering a promising solution. This study evaluates the degradation of State of Health (SOH) over 2.5 years for electrified buses under different charging protocols: DC Fast charging and Flash charging. The vehicles’ models, charging protocols, and financial implications are discussed. High-level simulations reveal that after 2.5 years, the Flash charging vehicle’s SOH reaches 88.93%, while the DC fast charging vehicle reaches 89.46%, showing a 0.47% difference. This slight variance is attributed to Flash charging vehicles avoiding full charge/discharge cycles, reducing battery aging impact. Considering this minimal SOH degradation difference, the choice between DC Fast charging and Flash charging primarily hinges on capital expenditure disparities. Flash charging, with its lower initial battery capacity and reduced capital costs, presents a compelling alternative for city busoperators seeking to electrify their fleets.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

The application of distributed fiber optic strain and temperature measurement can be utilized to address a multitude of measurement tasks across a diverse range of fields, particularly in the context of structural health monitoring in the domains of building construction, civil engineering, and special foundation engineering. However, a comprehensive understanding of the influences on the measurement method and the sensors is essential to prevent misinterpretations or measurement deviations. In this context, this study investigated the effects of moisture exposure, including various salt solutions and a high pH value, on a distributed strain measurement using Rayleigh backscattering. Three fiber optic sensors with different coating materials and one uncoated fiber were exposed to five different solutions for 24 hours. The study revealed significant discrepancies in deformation between the three coating types depending on the surrounding solution. Furthermore, in contrast to the prevailing literature, which predominantly describes swelling effects, a negative deformation was observed in a magnesium chloride solution. The findings of this study indicate that corresponding effects can impact the precision of measurement, potentially leading to misinterpretations. Conversely, these effects could be used to conduct large-scale monitoring of chemical components using distributed fiber optic sensing.

In recent experimental studies, we reported the aggravating effects of Asian sand dust (ASD) on male reproductive function in mice. However, the effects of fetal ASD exposure on male reproductive function have not been investigated. The present study investigated the effects of fetal ASD exposure on reproductive function in male offspring. Using pregnant CD-1 mice, ASD was administered intratracheally on days 7 and 14 of gestation, and the reproductive function of male offspring was determined at 5, 10, and 15 weeks after birth. The secondary sex ratio was significantly lower in the fetal ASD-exposed mice than in the controls. Histologic examination showed partial vacuolation of seminiferous tubules in immature mice. Moreover, daily sperm production (DSP) was significantly less in the fetal ASD-exposed mice than in the controls. DSP in the fetal ASD-exposed mice was approximately 10% less than the controls at both 5 and 10 weeks. However, both the histologic changes and the DSP decrease were reversed as the mice matured. These findings suggest that ASD exposure affects both the fetal development and the reproductive function of male offspring. In the future, it will be necessary to clarify the onset mechanisms of ASD-induced male fetus death and male reproductive disorders.