Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

this paper focuses on a scientific study of the restoration, rehabilitation and reuse of the great throne hall, the most important hall in al-jawhara palace. it also aims to study the most important factors and forces of damage that affected the great throne hall, natural, biological, and human, and the resulting damage. field tests were performed, laboratory tests to determine fracture stress, liquidity and spandex limits tests, chemical analysis on soil samples and geoelectrical testing of the soil, and the results did not show caves or voids in the ground until a depth of 10.00 m, construc-tion materials were studied and tested using x-ray, (xrd), mechanical tests (tensile, shear, com-pression), and a study of the effect of seismic loads on the walls; the results showed horizontal and vertical cracks; based on the study and analysis of these cracks, it was possible to present modern techniques in restoration and reinforcement methods, and in conclusion, the researcher's recommendations.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Ion association is an important process in aqueous dissolution, precipitation, and~crystallization of ionic inorganic, organic, and biological materials. Polyoxometalates (POMs) are good model compounds for understanding the complex relationships between lattice energy, ion-pairing in solution, and salt solubility. Here we perform calorimetric measurements to elucidate trends in cluster stability, lattice energy, and ion-pairing behavior studies of simple hexatantalate salts in neat water, parent hydroxide solutions, and molybdate melts, extending previous studies on the isostructural hexaniobates. High temperature calorimetry of alkali salts of hexatantalate reveals that the enthalpies of formation from oxides of the K, Rb, and Cs salts are more similar to each other than they are for their niobate analogues and that the tantalate cluster is energetically less stable than hexaniobate. Aqueous dissolution calorimetry reveals that the cesium salt of hexatantalate has a similar concentration dependence on its dissolution enthalpy to that of hexaniobate. However, unlike~rubidium hexaniobate, rubidium hexatantalate also exhibits increased concentration dependence, indicating that hextantalate can undergo increased ion-pairing with alkali salts other than cesium, despite the dilute environments studied. Dissolution enthalpies of POM salts in the parent alkali hydroxides shows that protonation of clusters stabilizes lattices even more than the strongly associating heavy alkali cations do. Additionally, neither weak nor strong lattice ion associations necessarily correlates with respectively high or low aqueous solubility. These studies illuminate the importance of considering ion-pairing among the interrelated processes in the aqueous dissolution of ionic salts that can be extended to serving as a model of cation association to metal oxide surfaces.

This work aims to investigate the effect of process temperature and catalyst content by thermochemical degradation of municipal solid waste (MSW) fraction (organic matter + paper + plastic) on the yield of reaction products (bio-oil, biochar, H2O and gas), physi-cochemical properties and chemical composition of bio-oils, as well as on the morphol-ogy and crystalline phases of biochar in laboratory scale. The organic matter, paper and plastic segregated from the gravimetric composition of total waste sample were subject-ed to the pre-treatments of drying, crushing and sieving. Thermal pyrolysis was per-formed at 400, 450 and 475 °C and 1.0 atmosphere, and catalytic pyrolysis at 450°C and 1.0 atmosphere, using 5.0, 10.0 and 15.0% (wt.) of FCC zeolite, bath mode, using a laboratory-scale borosilicate glass reactor. The bio-oil was characterized for acidic val-ue. The chemical functions present in the bio-oil identified by FT-IR and the composi-tion by GC-MS. Biochar was characterized by SEM/EDS and XRD. Thermal pyrolysis of the MSW fraction shows bio-oil yields between 9.44 and 9.24% (wt), aqueous phase yields between 21.93 and 18.78% (wt), solid phase yields between 67.97 and 40.34% (wt) and gas yields between 28.27 and 5.92% (wt). The bio-oil yield decreased with in-creasing process temperature. For the experiments using FCC, the biochar and gas yields slightly increased with increasing FCC content, while that of bio-oil decreased and the H2O phase remained constant. GC-MS of bio-oils identified the presence of hy-drocarbons and oxygenates, as well as nitrogen-containing compounds including am-ides and amines. The acidity of the bio-oil increased with increasing temperature and with the aid of FCC as a catalyst. The presence of hydrocarbons in bio-oil was identified by the addition of FCC catalyst due to the deoxygenation of carboxylic acids, followed by decarboxylation and decarbonylation reactions, producing aliphatic and aromatic hydrocarbons.

Psychrophilic anaerobic digestion emerges as an appealing integrated solution for the management of agricultural waste, particularly for farmers in regions where the average temperature does not exceed 26°C, as seen in coffee cultivation. Therefore, this study seeks to assess the biomethane potential of thermochemical treated coffee husk through psychrophilic anaerobic digestion (C3-20°C-w/pretreatment). To examine its viability, outcomes were compared with reactors operating at both mesophilic (C1-35°C) and psychrophilic (C2-20°C) conditions, albeit without the use of pretreated coffee husk. The C3-20°C-w/pretreatment test demonstrated a 36.89% increase (150.47 mL CH4/g VS; 161.04 mL CH4/g COD), while the C1-35°C test exhibited a 24.03% increase (124.99 mL CH4/g VS; 133.77 mL CH4/g COD), both in comparison to the C2-20°C test (94.96 mL CH4/g VS; 101.63 mL CH4/g COD). Notably, the C3-20°C-w/pretreatment trial yielded superior outcomes, accompanied by an associated energy output of 4262.2 KWh/year, sufficient to meet the annual energy demands of 588 residences. This marks an increase of 100 and 217 residences compared to mesophilic and psychrophilic AD of CH without pretreatment, respectively.

This work aims to investigate the effect of process temperature and catalyst content by pyrolysis and thermal catalytic cracking of (organic matter + paper) fraction from municipal household solid waste (MHSW) on the yields of reaction products (bio-oil, bio-char, H2O, and gas), acid value and chemical composition of bio-oils, and characterization of bio-chars, in laboratory scale. The collecting sectors of MHSW in the municipality of Belém-Pará-Brazil were chosen based on geographic and socio-economic database. The MHSW collected and transported to the segregation area. The gravimetric analysis of MHSW carried out and the fractions (Paper, Cardboard, Tetra Pack, Hard Plastic, Soft Plastic, Metal, Glass, Organic Matter, and Inert) separated. The selected organic matter and paper submitted to pre-treatment of crushing, drying, and sieving. The experiments carried out at 400, 450, and 475 °C and 1.0 atmosphere, and at 475 °C and 1.0 atmosphere, using 5.0, 10.0, and 15.0% (wt.) Ca(OH)2, in batch mode. The bio-oil characterized for acid value. The chemical functions present in bio-oil identified by FT-IR and the composition by GC-MS. The bio-char characterized by SEM, FT-IR and XRD. The variance in mass (wt.%) for organic fraction of municipal household solid waste, between 56.21 and 67.45% (wt.), lies with the interval of 56% (wt.) and 64% (wt.) of OFMHSW for middle and low income countries. The pyrolysis of MHSW fraction (organic matter + paper) show bio-oil yields between 2.63 and 9.41% (wt.), aqueous phase yields between 28.58 and 35.08% (wt.), solid phase yields between 35.29 and 45.75% (wt.), and gas yields between 16.54 and 26.72% (wt.). The bio-oil yield increases with pyrolysis temperature. For the catalytic cracking, the bio-oil and gas yields increase slightly with CaO content, while that of bio-char decreases, and the H2O phase remains constant. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, alkynes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, phenols, and aldehydes), as well as compounds containing nitrogen, including amides and amines. The acidity of bio-oil decreases with increasing process temperature and with aid Ca(OH)2 as catalyst. The concentration of hydrocarbons in bio-oil increases with increasing Ca(OH)2-to-MHSW fraction ratio due to the catalytic deoxygenation of fatty acids molecules, by means of de-carboxylation/de-carbonylation, producing aliphatic and aromatic hydrocarbons.

The present study shows a methodology for analyzing and designing a cylindrical packed-bed reactor considering stationary and dynamic models. The design comprises the reactor's stationary and dynamic governing differential equations for mass and heat transfer under multi-dimensional approaches. The results included simulation of concentration, temperature, and reaction rate profiles via the 1-D and 2-D differential equations solution with FlexPDE software. The analysis was complemented with a scaled 3-D dynamic model implemented in COMSOL Multiphysics. Both FlexPDE and COMSOL Multiphysics relied on the finite element technique to solve the governing differential equations. The simulated concentration and temperature profiles from both FlexPDE and COMSOL models were compared to experimental data gathered from literature (specifically from a Fischer-Tropsch process to produce low-molecular-weight hydrocarbons in a configuration of cylindrical packed-bed reactors). Simulated concentration and temperature profiles from the 2-dimensional dynamic model and the COMSOL model were in good agreement with the trend observed in experimental data. Finally, the predicted reaction rate profiles from the COMSOL model and the 2-dimensional dynamic model followed the temperature trend, thus reflecting the temperature dependence of the reaction.

Ti6Al4V samples obtained by selective laser melting were subjected to acid treatment, chemical oxidation in hydrogen peroxide solution and subsequent thermochemical treatment. The effect of temperature and time of acid etching of Ti6Al4V samples on surface roughness, morphology, topography and chemical and phase composition after the thermochemical treatment was studied. The surfaces were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and contact profilometry. Pore and protrusion sizes were measured. Acid etching modified the elemental composition and surface roughness of the alloy. Temperature had a greater influence on the morphology, topography and surface roughness of samples than time. Increases in roughness values were observed when applying successive chemical oxidation and thermochemical treatment compared to the values observed on surfaces with acid etching. After the thermochemical treatment, the samples with acid etching at a temperature of 80 °C showed a multiscale topography. In addition, a network-shaped structure was obtained on all surfaces, both on their protrusions and pores previously formed during the acid etching.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Mannosylerythritol lipids (MELs), one of the most promising biosurfactants (BS), are glycolipids produced by yeasts or fungi, with great environmental performance and a high compatibility with the human body. MELs besides working as typical surfactants, can form diverse structures when in the critical aggregation concentration (CAC), reducing the surface tension of water and other solutions, and being stable over a wide range of conditions. Among others, MELs present anti-microbial, antitumor, antioxidant and anti-inflammatory activity, skin and hair repair capacity, which opens possibilities for their use in applications from cosmetics and pharmaceutics to bio-remediation and agriculture. However, their market share is still low when compared to other glycolipids, due to their less developed production process and higher production cost. This re-view gathers information on the potential applications of MELs mentioned on the literature since 1993. Furthermore, it is also explored the current strategies being developed to enhance the market presence of MELs, in parallel with the ones developed for rhamnolipids and sophorolipids.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

The utilization of lignocellulosic biomass as an alternative energy source presents a promising opportunity to achieve a future energy system that is clean and free from CO2 emissions. To realize this potential, it is crucial to develop effective techniques for converting biomass and organic solid waste into secondary energy sources. Among the available options, hydrogen production stands out due to its numerous advantages, including its cleanliness, versatility in conversion and utilization technologies, high energy efficiency, and dense energy content per unit weight. This article offers a comprehensive overview of different conversion pathways and important technologies for generating hydrogen from biomass and organic solid waste. It specifically focuses on the thermochemical conversion process, which shows promise as an economically viable approach. While certain thermochemical conversion processes are still in the developmental phase, utilizing organic biomass for hydrogen production is widely recommended due to its ability to yield higher amounts of end products and its compatibility with existing facilities. However, it should be noted that this method necessitates a substantial amount of energy due to its endothermic nature. The article also explores alternative hydrogen conversion technologies and their potential for utilizing organic biomass as a feedstock, while addressing the challenges and limitations associated with these methods.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

In this study, nanostructured cerium-doped TiO2 (Ce-TiO2) films with the addition of different amounts of cerium (0.00, 0.08, 0.40, 0.80, 2.40, and 4.10 wt. %) were deposited on a borosilicate glass substrate, by flow coating sol-gel process. After flow coating, deposited films were dried at the temperature of 100 °C for 1 h, followed by calcination at the temperature of 450 °C for 2 h. For the characterization of sol-gel TiO2 films, the following analytic techniques were used: X-ray diffraction (XRD), thermal gravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry (DSC). Sol-gel derived Ce-TiO2 films were used for photocatalytic degrada-tion of the ciprofloxacin (CIP). The influence of the amount of Ce in TiO2 films, the duration of the photocatalytic decomposition, and the irradiation type (UV-A and simulated solar light) on the CIP degradation were monitored. Kinetics parameters (reaction kinetics constants and the half-life) of the CIP degradation, as well as photocatalytic degradation efficiency, were determined. The best photocatalytic activity was achieved by the TiO2 film doped with 0.08 wt.% Ce, under both UV-A, and solar irradiation.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The field of construction materials is pivotal in developing sustainable and resilient infrastructure. This demands continuous research to understand the properties and behaviors of these materials under diverse conditions. Although advancements in material science and numerical modeling have been significant, experimental testing remains indispensable for a thorough comprehension of material characteristics, particularly under extreme stresses and environmental factors. This need has forced the development of a wide array of testing techniques, each designed to evaluate specific engineering properties, thus creating a complex and varied landscape of experimental methodologies. This study provides a comprehensive overview of both conventional and innovative experimental testing techniques used to characterize construction materials. It explores the related methodologies and identifies potential gaps in their application within the industry. The spectrum of testing covered includes mechanical, chemical, thermal, microstructural, durability, physical, rheological properties, and non-destructive testing methods. Mechanical tests assess strength, hardness, and fatigue, whereas chemical analyses utilize techniques such as spectroscopy and chromatography. Thermal properties are examined using thermogravimetric analysis, and microstructural characteristics are explored through advanced imaging techniques. Durability testing focuses on materials’ resistance to environmental challenges, while physical properties tests evaluate aspects like porosity and water absorption. Rheological and non-destructive tests further examine materials’ behavior and integrity without causing damage. By discussing these methodologies, the study sheds light on various approaches to material evaluation and aims to enhance the selection, application, and development of testing standards. This overview seeks to inform and inspire future research and innovation in the science of construction materials, contributing to the development of more resilient and sustainable construction practices.

Improvement of hydrophysical properties and corrosion resistance of self-compacting concrete to the effects of alternate freezing-thawing and aggressive soils of southern and central Kazakhstan is of interest to a wide range of researchers from the side of practical application of the obtained results in construction practice. It is proposed to form a spatially reinforced fine crystalline structure of cement matrix with maximum dense packing by using a complex modifier (Hyperplasticiser + Polymer + Microsilica + Fibro fibers) in the composition of self-compacting concretes (SCC). The introduction of the calculated amount of the above additives increases the operational reliability of the current SCC compositions, increasing the water resistance to W16, frost resistance to F=500, increasing the compressive strength by 20%, reducing the mass loss of samples during corrosion leaching to 50%. It has been experimentally established that the proposed addition of complex modifier (Hyperplasticiser + Polymer + Microsilica + Fiber fibers) to the SCC composition allows obtaining self-compacting concrete of high quality with improved performance characteristics (compressive strength, water resistance, frost resistance and corrosion resistance). Studies have shown that the complex modifier-modified SCC compositions have a high degree of resistance in aggressive environments and leaching corrosion. Based on the results of the conducted tests, it is possible to recommend the obtained SCC compositions for production of building products working in the zone of alternating freezing-thawing and aggressive soils.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

Abstract. Results of research into four-membered phosphorus(V)-heterocycles, 2-halogen-1,2λ⁵-oxaphosphetanes are presented. The preparation of 2-halo-1,2λ⁵-oxaphosphetanes by reaction of P-haloylides with carbonyl compounds is described. The mechanism of asynchronous [2+2]-сycloaddition of ylides to aldehydes was proposed on the base of low-temperature NMR investigations. 2-Halogen-1,2λ⁵-oxaphosphetanes were isolated as individual compounds and their structures were confirmed by ¹Н, ¹³C, ¹⁹F and ³¹Р NMR spectra. These compounds are convenient reagents for preparing of various organic and organophosphorus compounds hardly available by other methods. Chemical and physical properties of the 2-halo-1,2λ⁵-oxaphosphetanes are reviewed. The 2-chloro-1,2λ⁵-oxaphosphetanes depending on substituents at the α-carbon atom rearrange with formation of 2-chloroalkylphosphonates or convert into trans-phosphorylated alkenes. Prospective synthetic applications of 2-halo-1,2λ⁵-oxaphosphetanes are analyzed. The 2-halo-1,2λ⁵-oxaphosphetanes may be easily converted to various alkenylphosphonates: allyl- or vinylphosphonates, phosphorus ketenes, thioketenes, ketenimines.

Artificial intelligence (AI) is revolutionizing the textile industry by improving the prediction of fabric properties and handfeel, which are essential for assessing textile quality and performance. However, the practical application and translation of AI-predicted results into real-world textile production remain unclear, posing challenges for widespread adoption. This paper systematically reviews AI-driven techniques for predicting these characteristics by focusing on model mechanisms, dataset diversity, and prediction accuracy. Among 811 papers initially identified, 26 were selected for in-depth analysis through both bibliometric and content analysis. The review categorizes and evaluates various AI approaches, including machine learning, deep learning, and hybrid models, across different types of fabric. Despite significant advances, challenges remain, such as ensuring model generalization and managing complex fabric behavior. Future research should focus on developing more robust models, integrating sustainability, and refining feature extraction techniques. This review highlights the critical gaps in the literature and provides practical insights to enhance AI-driven prediction of fabric properties, thus guiding future textile innovations.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Sustainable biomass production has significant potential for mitigating greenhouse gas emissions and is a promising alternative for the production of eco-friendly biofuels, biochemicals, and carbonaceous materials for biological, energetic, and environmental applications. Biomass from agroforestry and agricultural wastes is the richest natural carbon source and a sustainable option for woody biomass from a circular economic perspective. Portugal has several residues and by-products of agriculture, food processing, and forestry origin, and has a high availability of residual biomass. Portugal intends to reduce its dependence on energy imports and the use of fossil fuels, thereby increasing its economic performance while using biomass waste to produce high-value-added products. In this context, this review aims to explore the potential of agri-food wastes obtained from Portuguese industries via thermochemical conversion technologies as a promising sustainable alternative to woody biomass for the development of eco-friendly biofuels, biochemicals, and high-value carbonaceous materials and their applications. This strategy based on the circular bioeconomy concept can contribute to reducing the dependence on fossil fuels and minimising greenhouse gas emissions while meeting the demands of the growing population and providing a sustainable waste management solution.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

Sesamum indicum is considered an underutilized oil-bearing seed in the semi-arid regions of Ghana. Nonetheless, it is a promising source of food with both nutritional and therapeutic benefits. The aim of the present study was to evaluate the antioxidant properties S. indicum seeds using different extraction solvents. The seeds were obtained from the local farmers and prepared for analysis. The bioactive compounds present in the seeds were extracted using hexane, ethyl acetate, ethanol and water and their yields quantified. Total phenolic content (TPC), Condensed tannin content (TTC) and Total antioxidant capacity (TAC) , and DPPH radical scaveging assay were analyzed using standard methods. Antinutrients such as saponins, alkaloids, phytates and oxalates were also analyzed from the powdered seeds. Two chemometric methods; hierarchical cluster analysis (HCA) and Pearson correlation were employed to evaluate the interdependence of the various parameters to result in their antioxidant properties. The re-sults revealed that the solvents utilized had a significant impact on the extraction yield, phyto-chemical component concentration, and antioxidant activities. Hexane extracts of S. indicum seeds significantly exhibited the highest antioxidant activity (p < 0.05). It was marked with the highest TAC value of 232.6 ± 6.267 mg/g AAE and a strong DPPH scavenging activity with an IC50 of 52.81 ± 2.30 µg/mL. Correlations (p < 0.05) was established between TPC,CTC, TAC and DPPH radical scavenging activity) of the extracts. Antinutrients such as; phytate, oxalate, saponins and alkaloids were found to be 7.691 ± 0.8576, 1.501 ± 0.1375, 21.33 ± 4.619 and 317.33 ± 30.29 mg/g respectively. Data obtained suggest that S. indicum possess rich bioactive compounds that can be used in neutraceuticals and food products.

This study aims to investigate the effects of cement kiln dust (CKD) on the hydration reactions and mechanical properties of cement and to evaluate its potential for use as a supplementary cementitious material (SCM). The key variables are the CKD type and incorporation rate. Cement paste and mortar specimens containing CKD were prepared to examine their effects on the cement hydration and mechanical properties. The impact on hydration was assessed using setting time measurements, heat of hydration tests, and thermogravimetric analysis (TG). In addition, compressive strength tests were conducted to evaluate the effect of CKD on the mechanical properties of the cement. The results indicated that CKD promoted early cement hydration and enhanced the early age mechanical properties. However, owing to its lack of pozzolanic reactivity, it did not significantly affect long-term hydration. Given that the effects of CKD vary slightly depending on its chemical composition, careful consideration of CKD's properties suggests that its potential use as a SCM is promising.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Most available studies on the mechanical properties of apples lack the comprehensive results needed for the construction and validation of FEM models. Researchers typically focus on either the flesh and epidermis or the whole fruit, often overlooking the maturity stage of the examined apples. They usually report only firmness or the starch index as indicators of maturity. Furthermore, many studies use store-bought apples, which is impractical for industrial applications since this fruit have already undergone various treatments before reaching the shelf. This article aims to determine the mechanical properties of apples necessary for constructing FEM models that are both adequate and useful for the industry. The new Polish apple variety, Chopin, was selected as the research material. The study was conducted for three stages of apple maturity: development, ripening, and senescence. Mechanical properties of the flesh and skin were determined as material data for FEM models. Force-displacement curves and pressure-force functions were examined for future model validation. Using micro-computed tomography, the bruise volumes of fruit subjected to 20%, 50%, and 80% of the destructive force were determined. Significant differences were found between apples in the senescence stage and those in the development and ripening stages. Results of Micro-Ct and the results of modified and real compression tests of whole fruit have allowed us to formulate the research hypothesis regarding the influence of flesh cracking (characterized by local drops of force), influencing the bruise visibility and detection.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

This work presents the results of optimizing the physicochemical properties of composite briquettes based on microsilica for metallurgical-grade silicon production. Microsilica, a waste product of silicon production, contains a sufficiently high amount of silicon dioxide (96-97%). This fact makes microsilica a promising composite material for metallurgical processing. However, its granulometric composition limits its direct use. The method of briquetting on an industrial briquetting press was used. The influence of the granulometric composition of the composite mixture on the heat tolerance and strength of the finished briquettes was studied. The methods of obtaining and testing the briquettes, their composition, and the briquetting and drying process are described. The obtained briquettes were tested for the smelting of metallurgical silicon. The silicon recovery rate in the metal with the standard charge was 71%, while the recovery rate with the briquetted monocharge was 85%. The results of silicon smelting from the briquettes demonstrated the high quality of the obtained metal, corresponding to the standards of metallurgical-grade silicon. The implementation of these technologies not only improves the quality of the final product but also addresses environmental issues related to the disposal of microsilica, reducing its accumulation and minimizing its impact on the environment.

Fagao is one of China's traditional gluten free staple foods made by rice or corn flour. Corn Fagao prepared by co-fermentation with sourdough and yeast exhibits better quality and less staling compared to traditional yeast-fermented Fagao. The physicochemical properties of corn Fagao batter during the sourdough-yeast co-fermentation were investigated. The results showed that compared with yeast fermentation, the gas production and viscosity of the batter increased by co-fermentation. The co-fermented batter shows higher hydrolysis of starch and less amylose content. The integrity of starch granules in co-fermented batter was damaged more seriously, the crystallinity and short-range ordered structure were less than yeast fermented batter, even though the crystal structure type of starch did not change obviously. The peak viscosity, minimum viscosity, final viscosity, decay value and recovery value of corn batter are reduced by co-fermentation, which can improve the thermal stability of the batter and slow down the aging. Co-fermentation also results in a more pronounced reduction in protein subunit contents than yeast fermentation. The changes in the physicochemical properties of corn Fagao batter help explain the quality improvement of corn Fagao made from co-fermentation method, and may provide theoretical references for co-fermentation with sourdough and yeast to other gluten free foods.

Terrestrial orchid tubers are an important source of food in some parts of Africa and are traditionally included in the diets of most rural communities in Malawi. However, there is limited information on the nutritional and phytochemical content of the Malawian orchids to substantiate their traditional use. The present study evaluates the nutritional and phytochemical variation of four orchid species: Disa zombica, Satyrium buchananii, Satyrium carsonii, and Satyrium trinerve, collected from the same ecological zone of Malawi. The proximate content, minerals, phytochemicals, and functional properties were analysed using official procedures. Protein ranged from 2.19% to 4.65%, whereas carbohydrate ranged from 65.24% to 80.22%, with S. carsonii and S. trinerve registering the highest protein and carbohydrate contents, respectively. Iron and potassium were highest in D. zombica, while sodium and calcium were highest in S. buchananii. The total phenolics ranged from 228.56 to 500.00 mg GAE/100 g, with D. zombica registering the highest. The water absorption capacity ranged from 4.10 to 10.88 g/g. Albeit variable levels, the study provides evidence that orchid species contain essential nutrients and phytochemicals important for human nutrition and health. Furthermore, the functional properties can be utilised in the development of food products, such as baked products.

Hazelnuts are one of the most valuable nuts in the world due to their unique organoleptic properties and nutritional characteristics. This work was intended to analyze some physical and chemical properties of various hazelnut cultivars grown in Zakataly (Azerbaijan), namely Ata-baba, Elbari, Topqara, Firovan, Nasimi, Qalib, Mirzebeyli, Tala, Dash findiq, Barli, Azeri and Sachaqli. In general, the results showed statistically significant differences between the studied cultivars. The density of kernels, depending on the hazelnut cultivars, varied from 0.71 g/cm³ (Azeri) up to 1. 03 g/sm³ (Sachaqli). The peeled fruits of Dash findiq were heavier on average (1.64±0.34 g), and the peeled fruits of Nasimi, Qalib, Mirzebeyli and Sachaqli were lighter on average (0.8±0.23 g, 0.8±0.31 g, 0.8±0.20 g and 0.80±0.09 g, respectively. In the unpeeled form, Dash findiq nuts were the heaviest (3.70±0.34 g), and Nasimi and Qalib nuts were the lightest of all cultivars (2.0 ±0.48 g and 2.0 ±0.36 g, respectively). Ata-baba nuts account for 49 masses per kernel. %, in other studied cultivars - 33.3- 45.3 wt. %. Nasimi nuts are rounded (in the equatorial zone); Tala, Ata-baba, Firovan and Azeri - rounded-oblong; Topqara, Barli and Dash findiq – oblong; Elbari, Qalib, Mirzebeyli and Sachaqli - elongated. Firovan, Tala and Topqara have thicker shells. Ata-baba is significantly ahead of other varieties in the yield of kernels (490 kg / 1 ton of nuts), Tala is in second place in this indicator (453 kg / 1 ton of nuts), Topqara is in third (433 kg/ 1 ton of nuts). According to the maximum fat content, the cultivars Mirzebeyli (77.00±2.20 g/100 g of kernels) and Firovan (75.0±3.08 u/100 kernels), protein - Sachaqli (16.02±0.50 u/100 kernels) and Ata-baba (15.92±0.48 g/100 g of kernels) were distinguished. The results of this study help to better understand the differences between some varieties of hazelnuts grown in Azerbaijan, which provides important clues for all players involved in this sector.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

In this paper glass crystallization behavior of 50ZnO:47B2O3:3Nb2O3:0.5Eu2O3 (G-0h) glass has been investigated in detail by DSC, XRD and TEM analysis. The luminescent properties of resulted glass-ceramics were also investigated. By XRD and TEM analysis crystallization of several crystalline phases have been proved (α-Zn3B2O6, β-Zn3B2O6 and ZnNb2O6). By calculating of crystal parameters it was found that europium ions are successfully incorporated in the β-Zn3B2O6. Photo-luminescent spectra show an increased emission in the resulting glass-ceramic samples as compared with the parent glass sample because of the higher asymmetry of Eu3+ ions in the crystalline phases obtained. It was established that the optimum emission intensity is registered for glass-ceramic sample obtained after 25 hours heat treatment of the parent glass.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

The ability of thermoresponsive polymers to respond to temperature with a reversible conformational change makes them promising ‘smart’ materials for solutions in medical and biotechnological applications. In this work, two such polymers and structural isomers were studied: poly(N-isopropyl acrylamide) (PNiPAm) and poly(2-isopropyl-2-oxazoline) (PiPOx). We compare the critical solution temperatures (CST) of these polymers in D2O and H2O in the presence of Hofmeister series salts, as results obtained under these different solvent conditions are often compared. D2O has a higher dipole moment and electronegativity than H2O, which could significantly alter the CST transition. We used two complementary methods to measure the CST, dynamic light scattering (DLS) and differential scanning calorimetry (DSC), and found that the CST decreased significantly in D2O compared to H2O. In the presence of highly concentrated kosmotropes, the CST of both polymers decreased in both solvents. The influence of the kosmotropic anions was smaller than the water isotope effect at low ionic strengths but considerably higher at physiological ionic strengths. However, the Hofmeister anion effect was quantitatively different in H2O than in D2O, with the largest relative differences observed for Cl-, where the CSTs in D2O decreased more than in H2O measured by DLS but less by DSC. PiPOx was more sensitive than PNiPAm to the presence of chaotropes. It exhibited much higher transition enthalpies and multistep transitions, especially in aqueous solutions. Our results highlight that measurements of thermoresponsive polymer properties in D2O cannot be compared directly or quantitatively to application conditions or even measurements performed in H2O.

This paper reveals some properties of the cumulative entropy of consecutive k-out-of-n:F system's lifetime. First, we introduce a method for calculating the cumulative entropy of their lifetime and explore its preservation properties using established stochastic orders. Ad- ditionally, we obtain useful bounds that can used in situations where the distribution function of the system's component lifetimes are complicated or systems have large components. To support practical applications, we present two nonparametric estimators for the cumulative entropy of these systems. The efficiency and performance of these estimators are illustrated with simulated datasets and further validated with real data sets.

This study investigates the optical properties of Yttrium Orthoferrite thin films fabricated via plasma laser deposition. Yttrium Orthoferrite, a ferrimagnetic material known for its potential applications in spintronics and photonics, was deposited on single-crystal substrates under controlled conditions to analyze its optical characteristics. The influence of deposition time, on the film quality and optical properties was examined.

The targeted compounds in this research, resveratrol analogs 1–14 were synthesized as mixtures of isomers by the Wittig reaction using heterocyclic triphenylphosphonium salts and various benzaldehydes. The planned compounds were those possessing the trans-configuration as the biologically active trans-resveratrol. The pure isomers were obtained by repeated column chromatography in various isolated yields depending on the heteroaromatic ring. It was found that butyrylcholinesterase (BChE) was more sensitive to the heteroaromatic resveratrol analogs than acetylcholinesterase (AChE), except for 6, the methylated thiophene derivative with chlorine, which showed equal inhibition toward both enzymes. Compounds 5 and 8 achieved the highest BChE inhibition with IC50 values of 22.9 and 24.8 μM, respectively. The same as with AChE and BChE, methylated thiophene subunits of resveratrol analogs showed better enzyme inhibition than unmethylated ones. Two antioxidant spectrophotometric methods, DPPH and CUPRAC, were applied to determine the antioxidant potential of new heteroaromatic resveratrol analogs. Molecular docking of these compounds was conducted to visualize the ligand-active site complexes' structure and identify the non-covalent interactions responsible for the complex's stability, which influence the inhibitory potential. As ADME properties are crucial in developing drug product formulations, they have also been addressed in this work. The potential genotoxicity is evaluated by in silico studies for all compounds synthesized.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 < 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

As the carbon storage capacity of timber is recognized, there is growing interest in timber and wooden structures as a solution to various environmental problems. The use of Korean timber with substantial carbon storage capacity is required to reduce Korean carbon emissions and circulate timber resources. In this study, fire tests were conducted to investigate the charring properties of glued laminated timber columns made of Korean larch. The fire tests were conducted under both load-bearing and non-load-bearing conditions. The fire test results showed that the charring depth was affected by the corners of the section, and that the load ratio had an insignificant influence on the charring depth when the load ratio was 0.9 or less. This study provides data that can be used to compare the charring properties of laminated wood produced using South Korean larch with the charring properties of foreign standards. This provides reference data for developing fire-resistant design standards for timber structures made from South Korean timber.

Cementitious materials exhibit excellent binding properties and micropore structures that support the stabilization of TiO2 nanoparticles within the matrix. Therefore, these materials are ideal for the development of functional construction products with TiO2 nanoparticles. This study investigated the degree of hydration, microstructure, and mechanical properties of cement-containing TiO2 nanoparticles. The experimental results demonstrated that TiO2 nanoparticles accelerated the hydration rate of cement, reducing the setting times. Moreover, TiO2 nanoparticles changed matrix microstructure, decreasing the porosity and improving early-age strength. Although TiO2 nanoparticles function as nucleation sites in the cement hydration reaction, the tendency of the particles to clump implies that proper dispersion should be ensured when mixing in large quantities. When developing new building materials incorporating TiO2 nanoparticles, considering the effect of TiO2 nanoparticles on the hydration reaction of cementitious materials is crucial.

The pursuit of materials that offer both wear comfort and protection for functional and protective clothing has led to the exploration of weft-knitted spacer structures. Traditional cushioning materials such as spacer fabrics and laminated foam often suffer from deformation under compression stresses, thus compromising their protective properties. This study investigates the enhancement of the force absorption, stress-strain and thermal properties of weft-knitted spacer fabrics with inlays. Surface yarns with optimal stretchability and thermal properties are used and combined with elastic yarns in various patterns to fabricate nine different inlay samples. The mechanical and thermal properties of these samples are systematically analyzed, including their compression, stretchability, thermal comfort and surface properties. The results show that the inlay spacer fabric exhibits superior compression properties and thermal conductivity compared to traditional laminated foam and spacer fabrics, while maintaining stretchability, thus providing a better performance than traditional fabrics for protective clothing and wearable cushioning products. This study further confirms that the type of inlay yarn and inlay structure are crucial factors that significantly influence the thermal, tensile and compressive properties of fabric. This research provides valuable insights into the design and development of advanced textile structures to improve wear comfort and protection in functional garment applications.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

Visible-light photocatalysis, particularly in its application to organic synthesis, has experienced a big renaissance in the past decade. The rational design of new photocatalysts with designed and improved photocatalytic properties, that at the same time circumvents the necessity of using scarce and toxic transition metals, will predictably play a key role in photocatalysis in the next few years. Although free-base porphyrins were identified some years ago as a promising, easily accessible and easily tunable class of organic photoredox catalysts, a systematic study on the effect of the electronic nature and of the position of the substituents on both the ground-state and the excited-state redox potentials of these compounds is still lacking. We have prepared a set of known functionalized derivatives of meso-tetraphenyl porphyrin containing different substituents either in one of the meso-positions or at a beta-pyrrole carbon and we have determined their ground- and (singlet) excited-state redox potentials. This survey has led us to conclude that the introduction of a carbonyl group at the beta-pyrrolic position strongly increases the facility of the monoelectronic reduction of the porphyrin both in the ground state and in the singlet excited state. We have also prepared a second set of four previously unknown benzoyl derivatives of meso-tetraphenylporphyrin, and we have confirmed the validity of our conclusions.

The unique structure of G4.0 PAMAM dendrimers allows the drug to be enclosed in internal spaces or immobilized on the surface. In the conducted research, the conditions for the formation of the active G4.0 PAMAM complex with doxorubicin (DOX) were optimized. The physicochemical properties of the system were monitored using DLS, CD, and fluorescence spectroscopy. The QCM-D method was chosen to determine the preferential conditions for the complex formation. The highest binding efficiency of the drug to the cationic dendrimer was observed under basic conditions when the DOX molecule was deprotonated. The decrease in the zeta potential of the complex confirms that DOX immobilizes through electrostatic interaction with the carrier's surface amine groups. The binding constants were determined from the fluorescence quenching of the DOX molecule in the presence of G4.0 PAMAM. The two-fold way of binding doxorubicin in the structure of dendrimers was visible in the ITC isotherm. Fluorescence spectra and release curves identified reversible binding of DOX to the nanocarrier. Among the selected cancer cells, the most promising anticancer activity of G4.0-DOX was observed in A375 malignant melanoma cells. Moreover, the preferred intracellular location of the complexes concerning the free drug was found, which is important from a therapeutic point of view.

The article presents the results of research work devoted to improving the characteristics of paint and varnish coatings based on aqueous dispersions of polyacrylates, it is proposed to modify them by introducing mineral raw materials as fillers and hydrated lime with subsequent processing in a vortex layer apparatus. Introduction of activated diatomite does not cause deterioration of covering power, adhesion and increase of porosity of the paint material. Modification of coatings contributes to the increase of their operational properties, which can be associated with the reduction of free volume in the composite, formation of polymer boundary layers with modified physical and chemical properties. The aim of the study is to obtain water-dispersion paint and varnish composition containing modified diatomite on polyacrylate basis and subsequent study of the main physical and mechanical parameters. The work has been carried out by the following method: determination of porosity, adhesion, elasticity, covering power of the control composition; determination of porosity, adhesion, elasticity, and covering power of the obtained composites using modified filler; investigation of the influence of radiation in the infrared spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of research works it was noticed that modification of water dispersions with silica activated diatomite helps to eliminate the main disadvantages of materials and coatings based on acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate base does not lead to deterioration of the main performance characteristics of paint coatings - porosity, adhesion, elasticity and covering.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

The accuracy of cosmic ray observation by the Large High Altitude Air Shower Observatory Wide Field-of-view Cherenkov/fluorescence Telescope Array (LHAASO-WFCTA) is influenced by variations in aerosols in the atmosphere. The solar photometer (CE318-T) is extensively utilized within the Aerosol Robotic Network as a highly precise and reliable instrument for aerosol measurements. With this CE318-T 23, 254 sets of valid data samples in 394 days from October 2020 to October 2022 at the LHAASO site were obtained. Data analysis revealed that the baseline Aerosol Optical Depth (AOD) and A˚ngstro¨m Exponent (AE) at 440-870 nm (AE440−870nm) of the aerosols were calculated to be 0.03 and 1.07, respectively, suggesting that the LHAASO site is among the most pristine regions on Earth. The seasonality of the mean AOD are the order of spring > summer > autumn = winter. The monthly average maximum of AOD440nm occurred in April (0.11 ± 0.05) and the minimum was in December (0.03 ± 0.01). The monthly average of AE440−870nm exhibited slight variations. The seasonal characterization of aerosol types indicated that clean continental background aerosol predominated in autumn and winter, which is the optimal period for the absolute calibration of the WFCTA. Additionally, the diurnal daytime variations of AOD and AE across the four seasons are presented. Our analysis also indicates that the potential origins of aerosol over the LHAASO in four seasons were different and the atmospheric aerosols with higher AOD probably originate mainly from Northern Myanmar and Northeast India region. These results provide a baseline for comparison to the future on-site measurement of extinction coefficient profile and aerosol phase function by LHAASO-WFCTA, also enrich the valuable materials on aerosol observation in the Hengduan Mountains and Tibetan Plateau.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Broad bean paste (BBP) is a traditional fermented soy food, and its high salt content not only prolongs the fermentation time but also threatens human health. In this study, three BBP-meju with different salt concentrations were prepared, and the effects of varying salinity on the fermentation process were comprehensively compared. The results showed that salt-reduced fermentation contributed to the accumulation of amino acid nitrogen, reducing sugars, free amino acids, and organic acids. Alcohols, esters, aldehydes, and acids were the main volatile flavor compounds in BBP-meju, and the highest total volatile flavor compounds were found in medium-salt meju. Bacillus, Staphylococcus, Aspergillus, and Mortierella were the dominant microbial communities during fermentation, and there were also three opportunistic pathogens, Enterobacter, Pantoea, and Brevundimonas, respectively. According to Spearman correlation analysis, Wickerhamomyces, Bacillus, Staphylococcus, and Mortierella all showed highly significant positive correlations with ≥3 key flavor compounds, which may be the core functional flora. Furthermore, the dominant microbial genera worked synergistically to promote the formation of high-quality flavor compounds and inhibit the production of off-flavors during salt-reduced fermentation. This study provides a theoretical reference for the quality and safety control of low-salt fermented soy foods.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

This study introduces a novel and sustainable method of producing graphene from coconut shells and investigates its application in Graphene, Ni/Graphene, and Zn/Graphene electrodes for advanced energy storage devices. The graphene was synthesized scalably using a pyrolysis and impregnation technique, with its successful synthesis verified by X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), and electrical conductivity measurements characterizations. The study highlights the enhanced performance of Zn/Graphene electrodes, which outperform both pure graphene and Ni/Graphene variants. This superior performance is attributed to the smaller particle size of Zn (mean = 2.356 µm) compared to Ni (mean = 3.09 µm), and Zn’s more favorable electron configuration for electron transfer. These findings demonstrate the potential of bio-derived graphene composites as efficient, high-performance electrodes, paving the way for more sustainable and cost-effective energy storage solutions.

Freeze drying (FD) is a technique used to preserve the bioactive content and flavor of samples. Foods with a short shelf life due to nature have been preserved by FD in recent years. The success of the drying technique is thanks to the high retention ability of the bioactive compounds and the flavor of the sample. However, the high cost and energy consumption of the FD limit its usage in several fields. Freezing, primary drying, and secondary drying, which take place in the same device, are the stages of the FD. In addition, several parameters, including pretreatment, size, temperature, sample species, time, and pressure, affect the FD process. These parameters are controlled to increase the effectiveness of the FD on the samples. Moreover, FD was compared with other drying techniques including hot-air drying, microwave drying, vacuum drying, and solar drying to determine its protective capability. It has also been applied to the valorization of waste products, which is a common problem worldwide. For valorization, microencapsulation and powder production have been achieved by FD. In recent years, studies on the effects and use of the FD on various materials increased, providing new aspects for the future of science and food industry.

Advanced 1H Nuclear Magnetic Resonance (NMR) relaxometry and diffusometry methods and VIS-nearIR spectroscopy combined with pH, electric conductivity (EC) and totally dissolved solids (TDS) measurements were used to assess the properties of wastewater collected from a chicken slaughterhouse in each step of the treatment process (wastewater before treatment, biologically treated wastewater, chemically treated wastewater and discharged wastewater) and from sludge. The 1H NMR Carr-Purcell-Meiboom-Gill (CPMG) and Pulsed-Gradient-Stimulated-Echo (PGSE) decay curves recorded for all samples of wastewater were analyzed by inverse Laplace transform (ILT) to obtain the distributions of transverse relaxation times T2 and diffusion coefficient D. The VIS-nearIR total absorbance, T2-values, D-values, pH, EC and TDS parameters were used for statistical analysis in principal component analysis (PCA). The 1H T2-distributions measured for the slaughterhouse wastewater lie in two main regions reflecting the amount of dissolved solids or the distribution of undissolved solids mobility. The PCA analysis successfully differentiates between polluted and less polluted types of wastewater and sludge. The wastewater treatment applied by the slaughterhouse is efficient. The recommended methods for wastewater monitoring are the NMR T2- and D-distributions and EC, TDS and NMR-D diffusion coefficient. Finally, Machine Learning AI-algorithms are used to provide prediction maps of wastewater treatment stage.

A novel multicomponent glasses with nominal compositions of (50-x)MoO3:xWO3:25La2O3:25B2O3, x = 0, 10, 20, 30, 40, 50 mol% doped with 3 mol % Eu2O3 were prepared using a conventional melt quenching method. Their structure, thermal behavior and luminescent properties were investigated by Raman spectroscopy, differential thermal analysis and photoluminescence spectroscopy. Physical parameters as density, molar volume, oxygen molar volume and oxygen packing density were determined. Glasses are characterized with high glass transition temperature. Raman analysis revealed that the glass structure is built up mainly from tetrahedral (MoO4)2- and (WO4)2- units providing Raman bands of around 317 cm-1, 341-352 cm-1, 832-820 cm-1 and 928-935 cm-1. At the same time with the replacement of MoO3 with WO3 some fraction of WO6 octahedra are produced, which number increases with the increasing WO3 content. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (395 nm) excitation using the 7F0 →5L6 transition of Eu3+. PL emission gradually increases with increasing WO3 content evidencing that WO3 is more appropriate component than MoO3. The integrated fluorescence intensity ratio R (5D0 →7F2/5D0 →7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites.

Research on high-volume fly ash concrete, which utilizes large quantities of fly ash, has been actively conducted to promote resource recycling and reduce carbon dioxide emissions. However, while cement mixed with fly ash exhibits different temperature sensitivities compared to traditional cement, its hydration and mechanical properties vary depending on curing conditions. Despite this, there is a significant gap in research on this topic. In this study, high-volume fly ash concrete was produced with fly ash replacement rates of 35 % and 55 %. Compression strength tests were performed at various curing ages under three different curing temperature conditions, and the results were analyzed. Additionally, an isothermal calorimeter was used to analyze hydration characteristics under different curing conditions. The results indicated that concrete with high fly ash content was more sensitive to curing temperature compared to ordinary Portland cement.

Hierarchical tungsten oxide assemblies such as spindle-like, flowers with sharp petals, nanowires and regular hexagonal structures are successfully synthesized via a solvothermal reduction method by simply adjusting the reaction conditions. On the basis of the experimental results, it is determined that the reaction time significantly influences the phase transition, microstructure and photocatalytic activity of the prepared samples. The possible mechanisms for the phase transition and morphology evolution process have been systematically proposed. Moreover, the as-prepared products exhibit significant morphology-depended photocatalytic activity. The flower-like W18O49 prepared at 6 h possesses large specific surface area (150.1 m²g^-1), improved separation efficiency of electron-hole pairs and decreased electron-transfer resistance by the photoelectrochemical measurements. As a result, the flower-like W₁₈O₄₉ prepared at 6 h exhibits the highest photocatalytic activity for the degradation of Methyl orange aqueous solution. The radical trap experiments showed that the degradation of MO was driven mainly by the participation of h⁺ and •O²⁻ radicals.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

In this paper, a new way to obtain photoactive cements was presented. In this method amorphous TiO2 is added to cooler during the cooling of the cement clinker (Górażdże company) during cement production. Amorphous TiO2 was taken from the installation for obtaining titanium dioxide using the sulphate method. During the studies amorphous TiO2 was added to clinker at different temperature 300, 600, 700 and 800 °C. The properties of the obtained cement were tested during the bending and compressive strength and beginning and the end of bending setting time measurements. The adhesion of the obtained materials to concrete block, ceramic brick and plasterboard were also evaluated. The photocatalytic activity of the obtained materials was studied during NO and BTEX (benzene, toluene, ethylbenzene, p-,m-,o-xylenes decomposition) decomposition. Cement with 5 wt.% TiO2 added to clinker at 700 C had the highest photocatalytic activity and the best mechanical properties.

We investigate some information properties of consecutive k-out-of-n:G systems in light of fractional generalized cumulative residual entropy. We firstly derive a formula to compute fractional generalized cumulative residual entropy related to the system's lifetime and explore its preservation properties in terms of established stochastic orders. Additionally, we obtain useful bounds. To aid practical applications, we propose two non parametric estimators for the fractional generalized cumulative residual entropy in these systems. The efficiency and performance of these estimators are illustrated using simulated and real datasets.

Almost fifty years after the introduction of antibiotics as an antimicrobial agent, we are facing an increasing number of multi-resistant microbials. The search for new antimicrobial compounds emerged as a promising alternative to treatments for diseases caused by microorganisms such as fungi and bacteria. Thus, endophytic fungi are gaining recognition for their varied metabolites that may possess antimicrobial properties. In our research, we isolated, from Calea pinnatifida, six endophytic fungi identified as Colletotrichum siamense, Colletotrichum karstii, Hypomontagnella barbarensis, Neopestalotiopsis clavispora, Nigrospora sacchari-officinarum and Annulohypoxylon moriforme. Analyses of microbial secondary metabolites by utilizing UHPLC-HR-ESI-MS/MS in conjunction with molecular networking, allowed the annotation of 9 compounds, 5 of them from GNPS spectral library match, and 4 from prediction-based on the molecular network, and allowed the isolation of two pairs of Acyl-tetronic acid derivatives distereoisomeric identified by NMR spectrum. In this sense, the present study underlines the value of endophytic fungi as a reservoir of potentially new antimicrobial agents.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

Honey is a natural product that, thanks to its composition, particularly the high sugar content, is highly appreciated as an energy nourishment. In addition to sugars, it contains many other substances (carbohydrates, free amino acids, enzymatic proteins, organic acids, polyphenols) from which the therapeutic properties of honey arise: hydrating and osmotic activity, antimicrobial action, antioxidant and anti-inflammatory power. The present work aims to deepen the activity of skin protection exerted by honey, as a synergic result of its multiple therapeutic effects.Moreover, the study want to find possible correlations between biological properties and chemical-physical traits of honey. To carry out this research, five varieties of citrus honey, one of acacia honey, one of chestnut honey and, finally, one of multifloral honey were used. The honeys were first characterized by chemical-physical analysis (determination of water content, sugars, amino acids, polyphenols) and then subjected to qualitative melissopalynological analysis. Tests were also carried out to evaluate both their antioxidant power and the effect on collagenase, an enzyme involved in the degradation of collagen present in the extracellular matrix and, therefore, in the processes of skin aging. Finally, they were used in in vitro experiments to assess their action in stimulating cell viability and proliferation on human keratinocytes.

Two experiments were conducted to develop a Nano green manganese and assess its effect on grapevines. The first experiment was microbiological, where several incorporation strategies were utilized to enrich the yeast with manganese, as follows: (1) adding manganese to the liquid medium (growth phase), (2) adding after 24 h of incubation (non-growth phase). As the results, growth phase reduced the possibility of medium contamination. Manganese concentration in the yeast cells was increased as that of manganese sulphate in the medium. Manganese incorporation in yeast cells was 99.93% higher than that of the medium at 0.0195 g/l of manganese. Although the concentration of manganese in the medium raised the OD of yeast cell biomass, manganese sulphate had no passive influence on it. The second experiment was horticultural, done on Flame Seedless grapevines, since both active fresh and frozen yeast enriched with manganese resulted from the first experiment were sprayed twice a year at 10 or 20 cm3/l comparing with manganese sulphate, and manganese chelate. The results demonstrated that yeast extracts in both forms increased the yield and improved fruit properties. The most effective treatment on vegetative growth, yield and fruit properties was the frozen yeast enriched with manganese at 20 cm3/l.

Ca2+ can boost protein-protein interactions and, if present at an appropriate level, can potentially improve the physicochemical properties of protein gels and films. This study aimed to determine the effect of CaCl2 (0, 0.01 0.025 0.05% w/w) on the optical, water affinity, and mechanical char-acteristics of glycerol (Gly)- and sorbitol (Sor)-plasticized pea protein isolate (PPI) films. The CaCl2 caused darkening and a color shift of the films from yellow to yellow-green. Additionally, de-creased light transmission, particularly in the UV range, and reduced moisture content were observed. The CaCl2 decreased the water vapor permeability (WVP) of the Gly-plasticized film by an average of 20%, with no effect on the Sor-plasticized film. All films were completely soluble in water. The CaCl2 negatively impacted the mechanical integrity of the films, reducing the tensile strength of the Gly- and Sor-plasticized films by ~16% and 14-37%, respectively. Further increases in CaCl2 content (0.1% and 0.2% w/w) led to concentration-dependent cracks, suggesting protein over-crosslinking. In summary, the incorporation of CaCl2 into PPI films did not provide signif-icant benefits and actually worsened key properties such as transparency and mechanical strength. The type of plasticizer influenced how CaCl2 affected some properties of the PPI film.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

Organic fertilizer application in agricultural land is known to improve soil microbial processes, fertility, and yield. In particular, stable changes in soil chemical composition through multi-year fertilization of organic fertilizers are thought to cause changes in the microbial community. Here, the effects of oil cake amendments (OC) on soil bacterial diversity, community profile and enzyme activity were evaluated and compared to those amended with chemical fertilizer (NPK). The comparison of diversity indices between OC and NPK amended soils shows that application of oil cake has increased microbial diversity potentially with an increase in the number of different microbial groups. The ordination plot distinguished and clustered both treatments showing differential effects of soils chemical factors on the microbial communities of each treatment. Proteobacteria, Verrucomicrobia and Bacteriodetes were significantly abundant in OC amended soil than in the NPK received soil, indicating alterations in community structure, composition, and diversity con-current to the changes in pH, Ca and Mg contents of the soil. These shifts in bacterial community structure and composition could also be observed from the phylum to the genus level in both NPK and OC amended soils partially explained by differences in soil chemical factors. The OC soil compared to the NPK amended soil also contain significantly higher abundance of predicted genes corresponding to enzymes related to biogeochemical cycling, decomposition and plant growth promotion. Collectively, these results support the use of an unconventional organic fertilizer positively altering bacterial populations in jujube orchards. The application of oil cake-based organic fertilizer improved microbial diversity and enhanced potential ecosystem functions related to bio-geochemical cycles, mineralization and plant growth promotion.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

The mechanical properties of the materials stored inside agricultural silos influence the loads generated inside them. The different silo calculation methodologies allow predicting these loads under static and dynamic conditions if the mechanical properties of the stored materials are known. It has been known for many years that these properties are highly dependent on the moisture content of the material. However, to date there are not many studies focused on its determination. The goal of this research is the determination of the angle of internal friction, apparent cohesion, dilatancy angle and apparent specific weight of maize subjected to different moisture contents. Direct shear and oedometer assay devices were used for this purpose. In addition, the maize samples used were moistened using a climatic chamber. Moisture contents applied to maize sample ranged from 9.3% to 17.4%. The results obtained for the angle of internal friction and apparent cohesion, as well as those obtained for the apparent specific weight, were similar to those reported in the literature. However, the values obtained for the dilatancy angle of maize as a function of moisture content could not be compared because nothing has been published so far. The values obtained for this parameter overlap with those published for this material under ambient conditions. In addition, no direct relationship between the values obtained for this parameter and the moisture content of the sample could be found. Finally, the apparent specific weight increased with increasing moisture content of the samples, which differed from that published in the literature. The values provided here can be used for the optimization of storage and handling structures for granular agricultural materials using numerical methods.

The aim of the present study was to investigate the incidence of breast (females), prostate, testicular and thyroid cancer in the Italian National Priority Contaminated Sites (NPCSs), served by cancer registries, where the presence of endocrine disruptors (EDs), reported to be linked to these tumors, was documented. Evidence of carcinogenicity of EDs present in NPCs was assessed based on evaluation by international scientific institutions/committees. Standardized Incidence Ratios (SIRs) were computed for each NPCS and cancer site with reference to the time window 1996-2005. Excess incidence of one or more cancer site at study was found in twelve out of fourteen NPCSs. Significantly increased SIRs were found for breast cancer in eight NPCSs, for prostate cancer in six, for thyroid cancer (both gender) in four and for testicular cancer in two. Non significantly increased SIRs were found in five NPCSs for testicular cancer and in two for thyroid cancer (males). Even if increased incidence of one or more cancer sites at study were found in several NPCSs, the ecological study design and the multifactorial etiology of the considered tumors do not allow reaching conclusions in terms of causal links with environmental contamination. In light of the observation of some excesses in SIRs, continuing epidemiological surveillance is warranted.

The present study drops the line for the flow characteristics of fly ash-based (FA) geopolymers reinforced with polypropylene (PP) fibers undergoing the extrusion process during three-dimensional printing. Applying to the Herschel-Bulkley rheological model the research is ready with the sound theoretical basis which is used to understand the flow behavior of these materials under various conditions. A combination of experimental and numerical techniques that are based on the Finite Element Method (FEM) in COMSOL has been used in this study. The results of both the experimental and simulation approaches are then compared and the behavior of the material during extrusion is then examined. The experimental results proved PP fiber content has significant effects on rheological properties. The experiments on mixes which are either devoid of fibers or possess a high content of fiber, encountered problems like a high static yield stress and material segregation. Mixes with fibers of moderate content showed smoother extrusion processes, which means that a suitable range of fiber addition exists for the fibers that optimally balance the mechanical properties and extrudability. Numerical simulations typically agreed with experimental data for fiber contents up until it reached a certain level but not above, suggesting the existence of more complex interactions inside the fibers and the necessity for the subsequent model refinements. The investigation outlines a 0.25% and 0.5% fiber content range that leads to enhanced performance without bringing the extrusion process to greater complications and further making the production of proper, architecturally printed structures possible.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

This study primarily investigates the effect of fly ash (FA) content on the mechanical properties and hydration performance of alkali-activated ground granulated blast furnace slag cements (AAGC), and compares the related properties with ordinary Portland cement (OPC). Additionally, the study examined the hydration products, thermal analysis, MIP, SEM, chemically bound water, and pH values of AAGC. The compressive strength of AAGC showed a retrogression phenomenon from 3 to 28 days, with the 14-day and 28-day compressive strengths of AAGC being higher than those of OPC. The AAGC with 20% FA content exhibits the highest 28-day compressive strength (75 MPa). The hydration heat release rate curved of OPC and AAGC can be divided into the initial induction period, induction period, acceleration period, deceleration period and steady period. As FA content increases, the 28-day pore volume of AAGC increased while pH values and chemically bound water decrease. SEM images of AAGC with low FA content showed more microcracks.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

The laser melting process (DED-LB-p) is used for the production of large components due to the high deposition rates. The large number of process parameters and printing strategies makes it difficult to optimize this process to achieve the optimal properties. Intensive post-processing is still the main obstacle to the widespread use of this process. In this work, the relationship between different printing strategies, printing strategies and process parameters on the microstructural, and tensile mechanical performance at room temperature is investigated. The porosity was measured in both printing directions. Grain orientation and size were analyzed by EBSD. A very low porosity of less than 0.4% was found in all printed samples. The samples printed with the optimized offset printing strategy show a significant improvement in tensile strength of 1000 MPa without heat treatment compared to other processing routes.

The research focuses on the production of particleboards from the biomass of energetic willow (Salix viminalis L.) and energetic poplar (Populus spp.), aiming to explore their feasibility as sustainable materials for various applications. Energetic willow and energetic poplar are known for their rapid growth and suitability for energy production. They present an intriguing alternative as raw materials with added value for particleboard manufacturing. The study investigates the selected mechanical and physical properties of the produced particleboards, considering parameters such as density profile, bending strength, modulus of elasticity, water absorption, thickness swelling, and screw withdrawal resistance. During the research, the results were also compared between different mass shares of willow and poplar particles in the particleboards. The findings underscore the promising potential of willow and poplar-based particleboards as eco-friendly alternatives in the construction and furniture industries, contributing to resource efficiency and carbon emission reduction efforts.