Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

Thermoplastic pultrusion is a suitable process for fabricating continuous unidirectional thermoplastics with a uniform cross-section, high mechanical properties due to continuous fiber reinforcement, low cost, and suitability for mass production. In this paper, jute and glass fibers were reinforced with a polypropylene matrix and fabricated using the thermoplastic pultrusion process. The volumetric fraction of the composite was designed by controlling the filling ratio of the reinforcing fiber and matrix. The effects of molding parameters were investigated, such as pulling speed and molding temperature, on the mechanical properties and microstructure of the final rectangular profile composite. The pulling speed and molding temperature were varied from 40 to 140 mm/min and 190 to 220°C, respectively. The results show that an increase in molding temperature initially led to an increase in mechanical properties, up to a certain point. Beyond that point, they started to decrease. The increase in molding temperature also led to an increase in void content. Meanwhile, un-impregnation decreased with the increase in molding temperature, and the jute fiber began to degrade at high temperatures. In the next step, with varying pulling speed, the mechanical properties decreased as the pulling speed increased, with a corresponding increase in void content and un-impregnation. The decrease in mechanical properties was influenced by the increase in void content and un-impregnation, as the jute fiber degraded at higher temperatures.

Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

With a view to sustainable development and circular economy, this work focused on the possibility to valorize a secondary waste stream of recycled carbon fiber (rCF) to produce a 3D printing usable material with PA6,6 polymer matrix. The reinforcing fibers implemented in the present research are the result of a double recovery action: starting with pyrolysis from which long fibers are obtained, used to produce non-woven fabrics and, subsequently, fiber agglomerate wastes obtained from this last process are ground in a ball mill. The effect of a different amount of reinforcement at 5% and 10% by weight on the mechanical properties of 3D printed thermoplastic composites was investigated. Although the recycled fraction was successfully integrated in the production of filaments for 3D printing and therefore in the production of specimens via Fused Deposition Modeling technique, the results showed that fibers did not improve the mechanical properties as expected, due to an unsuitable average size distribution and the presence of a predominant dusty fraction ascribed to the non-optimized ball milling process. PA6,6 + 10 wt.% rCF composites exhibited a tensile strength of 59.53 MPa and a tensile modulus of 2.24 GPa, which correspond to an improvement in mechanical behavior of 21 5 % and 5 21 % compared to the neat PA6,6 specimens, respectively. The printed composite specimens loaded with the lowest content of rCF provided the greatest improvement in strength (+ 9% over the neat sample). Then, a prediction of the “optimum” critical length of carbon fibers was proposed that could be used for future optimizations of the recycled fiber processing.

Dye wastewater containing bisphenol A (BPA) and dyes as pollutants have not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI:PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g, whereas for BPA, it decreased from 26.7 to 22.8 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexist, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. Thus, PDA/PEI TPU NFMs exhibit the potential for removal of dye–BPA composites, whereas binary systems containing BPA with different dyes are adsorbed differently.

The present study describes the preparation of a composite material consisting of thermoplastic polyurethane-poly (n-isopropylacrylamide) (TPU-PNIPAM), which was employed for the se-lective adsorption separation of alcohol/water mixed solutions for the first time. The findings revealed that TPU and PNIPAM were interconnected through interchain hydrogen bonding, resulting in exposed hydrophobic isopropyl groups while covering the hydrophilic hydrogen bond sites. Selective separation of alcohols from alcohol/water mixed solutions occurred via London dispersion forces between alkyl groups. Increasing the PNIPAM load on the TPU surface led to a decrease in available hydrogen bond sites capable of bonding with water molecules, an increase in dispersible isopropyl groups interacting with alcohol alkyl groups, and enhanced selective adsorption capacity of TPU-PNIPAM towards alcohol/water mixed solutions. Moreover, TPU-PNIPAM exhibited a characteristic fast-slow-fast-equilibrium ad-sorption curve for different initial concentrations of alcohol/water mixtures, and its selective adsorption capacity increased when temperature reached 55℃. In addition to these general trends, under identical conditions, the selective adsorption capacity of TPU-PNIPAM gradually increased by methanol < ethanol < isopropyl alcohol < propyl alcohol, thus indicating a positive correlation between selectivity performance and hydrophobicity level.

The optimization of production of lignin-nanofiber-filled thermoplastic starch composite film for potential application in food packaging was carried using Response Surface Methodology (RSM), through the adoption of the Box-Wilson Central Composite Design (CCD) with 1 center point. The effects of filler loading on moisture absorption (MAB), tensile strength [TS], percent elongation [PE] and Young’s modulus [YM]) of the films were investigated in order to construct the desirability indices of the composite. The quality of the fitting model was expressed by the coefficient of determination, R2 and the adjusted R2. Results showed that the nanocomposite films were best fitted by a quadratic regression model with a high coefficient of determination (?2) value. The selected film has desirability of 76.80%, close to the objective function, and contained 4.81% lignin and 5.00% nanofibre. The MAB, TS, YM and PE of the selected film were 17.80 %, 21.51 MPa, 25.76 MPa and 48.81%, respectively. The addition of lignin and nanofiber to starch composite reduced the moisture absorption tendency but increased the mechanical properties of the films due to the good filler/matrix interfacial adhesion. Conclusively, results suggested that these films would be suitable for packaging application.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Over the past decades, research has escalated on the use of polylactic acid (PLA) as replacement for petroleum-based polymers. This is due to its valuable properties, such as renewability, biodegradability, biocompatibility and good thermomechanical properties. Despite possessing good mechanical properties comparable to conventional petroleum-based polymers, PLA suffers from some shortcomings such as low thermal resistance, heat distortion temperature and rate of crystallization, thus different fillers have been used to overcome these limitations. In the frame work of environmentally friendly processes and products, there has been growing interest on the use of cellulose nanomaterials viz. cellulose nanocrystals (CNC) and nanofibers (CNF) as natural fillers for PLA towards advanced applications other than short-term packaging and biomedical. Cellulosic nanomaterials are renewable in nature, biodegradable, eco-friendless and they possess high strength and stiffness. In the case of eco-friendly processes, various conventional processing techniques, such as melt extrusion, melt-spinning, and compression moulding, have been used to produce PLA composites. This review addresses the critical factors in the manufacturing of PLA-cellulosic nanomaterials by using conventional techniques and recent advances needed to promote and improve the dispersion of the cellulosic nanomaterials. Different aspects, including morphology, mechanical behavior and thermal properties, as well as comparisons of CNC- and CNF reinforced PLA, are also discussed

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

In this study, effects of molecular structure transformation of canna starch (CS) in oxidation condition on physicochemical characteristics of thermoplastic starch were examined. Thermoplastic starch (TPS) samples of CS and respective oxidized starch (in 1, 3 and 5% of sodium hypochlorite, w/w) were prepared by using an internal mixer with the presence of 30 wt% of glycerol as plasticizer. The physicochemical, morphological, thermal, and mechanical properties of native starch-based TPS (NTPS) and oxidized starch-based TPS (OTPS) samples were evaluated. The content of carboxyl and carbonyl groups in oxidized canna starch (OCS) increased with the increase in the content of oxidant, leading to an improvement in the plasticization of CS. FTIR spectra of OTPS samples showed the stronger interaction between oxidized starch and plasticizer. SEM images of fracture surface indicated that the morphology of OTPS samples were smoother than that of NTPS samples. XRD patterns confirmed that the crystallite type of starches was also clearly changed after extrusion process and the decrease in crystallinity of OTPS samples is attributed to effects of both oxidation and plasticization. DSC results indicated that Tg of OTPS was greatly influenced by the carbonyl and carboxyl content and the higher content of these groups in oxidized starched could help the plasticization becomes easier. The better plasticization in OTPS samples resulted in the better mechanical properties and thermal stability of OTPS. The outcome suggested that the use of oxidized starch is an effective method to improve the plasticization in preparing thermoplastic starch.

The use of biodegradable materials has a growing field of application due to environmental concerns, however, scientific research on incremental forming using biomaterials is scarce. Thus, this study focuses on the single point incremental forming (SPIF) process applied to a composite sheet that combines a biodegradable thermoplastic matrix (Solanyl) reinforced with natural fibres (flax). The influence of the process parameters on the final geometry is determined, evaluating the effect of the following factors: step depth, wall angle and temperature reached during the process. Additionally, a heated aqueous medium is incorporated which facilitates the formability of the composite sheets. This method is especially useful for materials that have poor formability at room temperature. The benefits of using controlled heat include the reduction of formation forces applied to the plate, improved accuracy due to the reduction of elastic recovery, and the manipulation of the samples remarkably close to the glass transition temperatures. Through this experimental study with the variables analysed, a maximum shaping depth of 310 mm is obtained. These results confirm that the single point shaping used with bioplastic materials is possible and has positive outcomes for incremental forming.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Thermoplastic composites are continuously replacing thermosetting composites in lightweight structures. However, the accomplished work on the fatigue behavior of thermoplastics is quite limited. In the present work, we propose a numerical modeling approach for simulating fatigue delamination growth and predicting the residual tensile strength of quasi-isotropic TC 1225 LM PAEK thermoplastic coupons. The approach is supported and validated by tension and fatigue (non-interrupted and interrupted) tests. Fatigue delamination growth is simulated using a mixed-mode fatigue crack growth model, which is based on the cohesive zone modeling method. All interfaces between the thermoplastic plies were modelled using cohesive elements. Quasi-static tension analyses on pristine and fatigued coupons were performed using a progressive damage model implementing a set of Hashin-type strain-based failure criteria and a damage mechanics-based material property degradation module. Using the fatigue model, delamination growth was predicted as a function of number of cycles at all interfaces. The results agree well with C-scan images taken on fatigued coupons during interruptions of fatigue tests. An unequal and unsymmetric delamination growth was predicted due to the quasi-isotropic lay-up. Moreover, the combined models capture the decrease in the residual tensile strength of the coupons. In the quasi-static tension analysis of the fatigued coupons, the driving failure mechanisms are the fast propagation of the pre-existing delamination and the severe matrix cracking.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

The structural evolution and phase composition of multi-block thermoplastic polyurethanes, with different nature of the soft segments based on poly(butylene adipate) (PBA), were analyzed during in-situ thermal treatments. A combination of synchrotron small- and wide-angle X-ray scattering, differential scanning calorimetry, thermogravimetric analysis, and FTIR spectroscopy was used to determine the influence of macrodiol nature and crystallization conditions on the polymorphic behavior of PBA. Using a new synthesis scheme, a relatively high degree of crystallinity for urethane blocks was achieved, which depends on the diisocyanate type in the structure of the soft segment. The hard segment domains impose geometrical constraints on PBA, thereby altering its crystallization process compared to the neat oligomer. Thus, crystallization after annealing at a low temperature (80 °C) is fast, predominantly yielding a metastable β-phase. When heated to 180 °C, which is higher than the hard-segment melting temperature, a phase-separated structure is observed. Subsequent crystallization is slower, favoring the formation of the stable α-PBA modification. The phase separation can be observed even after the hard block melting. A notably slow crystallization from an isotropic melt was documented after the disruption of phase separation at 230 °C.

The way in which a perforated structure is formed has attracted much interest in the porous membrane research community. This novel structure gives materials an excellent antifouling property as well as a low operating pressure and other benefits. Unfortunately, the current membrane fabrication methods usually involve multi-step processes and the use of organic solvents or additives. Our study is the first to offer a way to prepare perforated membrane by using a physical foaming technique with CO₂ as the blowing agent. We selected thermoplastic polyurethane (TPU) as the base material because it is a biocompatible elastomer with excellent tensility, high abrasion resistance, and good elastic resilience. Various processing parameters, which included the saturation pressure, the foaming temperature, and the membrane thickness, were applied to adjust the TPU membrane’s perforated morphology. We proposed a possible formation mechanism of the perforated membrane. The as-prepared TPU membrane had good mechanical properties with a tensile strength of about 5 MPa and an elongation at break above 100%. Such mechanical properties make this novel membrane usable as a self-standing filter device. In addition, its straight-through channel structure can separate particles and meet different separation requirements.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

Currently, petroleum-derived plastics are widely used. However, one of its main disadvantages is its low degradation time, which is not beneficial to the environment. Therefore, natural polymers are an alternative to overcome this obstacle. Among the natural polymers, starch can be highlighted. Thus, the objectives of our investigation were to obtain sisal nanofibers using low concentrations of acid solutions to produce and characterize corn starch nanocomposites reinforced with these nanofibers. The films were produced by a casting technique using commercial corn starch and glycerol as plasticizing agents; the nanofibers were obtained using acid hydrolysis. The films were subjected to tensile tests to evaluate their resulting mechanical behaviors. The results of X-ray diffraction and transmission electron microscopy analyses revealed the possibility of obtaining cellulose nanofibers using a sulfuric acid concentration lower than that previously reported in the literature. The nanocomposites reinforced with plant nanofibers showed lower tensile stress and elongation characteristics than the matrices without nanofibers.

This review provides an extensive overview of the developments in the field of polymer science, focusing on the solid-state modification (SSM) of thermoplastic materials. The background of the study places thermoplastics within the context of their increased use over the past century, highlighting their versatility in various applications and the associated environmental and health concerns due to certain additives. The methods section delves into the specifics of SSM, a technique that involves the incorporation of monomers or oligomers into the amorphous phase of polymers through multiple exchange reactions, distinguishing it from traditional melt polymer modification methods. The results section outlines the unique aspects of SSM and its increasing recognition for its potential to enhance material performance in areas such as catalysts and composites. It also discusses the application of SSM in modifying different thermoplastic polymers, highlighting various studies demonstrating the method's effectiveness in altering polymer properties. Finally, this work emphasizes SSM's importance in environmental sustainability and its potential in the recycling and upcycling of plastic materials. It acknowledges the challenges and future perspectives in the field, particularly regarding the scalability of SSM techniques for industrial applications and their role in advancing a circular economy in the polymer industry.

Thermoplastic molded regenerated silk was proposed as structural material in tissue engineering applications, mainly for application in bone. The protocol allows to obtain a compact non-porous material with a compression modulus in the order of a Giga Pascal starting from silk fibroin by compressing a silk fibroin lyophilized sponge of powder in mold at temperature higher than the glass transition temperature (Tg). The main purpose of the produced resin was the osteofixation and other structural applications in which the lack of porosity was not an issue. In this work, we introduced the use of citric acid in the thermoplastic molding protocol of SF to obtain a porosity inside the structural material. In addition to the previously developed protocols the addition of citric acid allowed us to obtain a structural material. The CA powder during the compression acted as a template for the pore formation. In addition, the CA was able to effectively crosslink the SF chain improving the mechanical strength. This effect was proved both evaluating the compression modulus and by studying the spectra obtained by Fourier infrared spectroscopy (FTIR). This protocol may be applied in the near future to the production of a structural bone scaffold.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

In the past few years, micromodels have become a useful tool for visualizing flow phenomena in porous media with pore structures, e.g., the multifluid dynamics in soils or rocks with fractures in natural geomaterials. Micromodels fabricated using glass or silicon substrates incur high material cost; in particular, the microfabrication-facility cost for making a glass or silicon-based micromold is usually high. This may be an obstacle for researchers investigating the two-phase-flow behavior of porous media. A rigid thermoplastic material is a preferable polymer material for microfluidic models because of its high resistance to infiltration and deformation. In this study, cyclic olefin copolymer (COC) was selected as the substrate for the micromodel because of its excellent chemical, optical, and mechanical properties. A delicate micromodel with a complex pore geometry that represents a two-dimensional (2D) cross-section profile of a fractured rock in a natural oil or groundwater reservoir was developed for two-phase-flow experiments. Using an optical visualization system, we visualized the flow behavior in the micromodel during the processes of imbibition and drainage. The results show that the flow resistance in the main channel (fracture) with a large radius was higher than that in the surrounding area with small pore channels when the injection or extraction rates were low. When we increased the flow rates, the extraction efficiency of the water and oil in the mainstream channel (fracture) did not increase monotonically because of the complex two-phase-flow dynamics. These findings provide a new mechanism of residual trapping in porous media.

Quaking aspen (Populus tremuloides Michx.) is an important deciduous species in western U.S. forests. Existing maps of aspen distribution are based on Landsat imagery and often miss small stands (&lt;0.09 ha or 30 m²), which rapidly regrow when managed or following disturbance. In this study, we present methods for deriving a new regional map of aspen forests using one year of Sentinel-1 (S1) and Sentinel-2 (S2) imagery in Google Earth Engine. We assessed the annual phenology of aspen in the Southern Rockies and leveraged the frequent temporal resolution of S1 and S2 to create ecologically relevant seasonal composites. Additionally, we derived spectral indices and radar textural features targeting the canopy structure, moisture, and chlorophyll content. Using spatial block cross-validation and Random Forests, we assessed the accuracy of different scenarios and selected the best performing set of features for classification. Comparisons were then made with existing landcover products across the study region. The resulting map improves on existing landcover products in both accuracy (average F1-score = 93.1%) and detection of smaller forest patches. These methods enable accurate mapping at spatial and temporal scales relevant to forest management for one of the most widely distributed tree species in North America.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

This paper presents a proof-of-concept study on the biocolonization of 3D-printed hydroxyapatite scaffolds with mesenchymal stem cells (MSCs). Three-dimensional (3D) printed biomimetic bone structure made of Calcium Deficient HydroxyApatite (CDHA) intended as future bone graft was made from newly developed composite material for FDM printing. The biopolymer polyvinyl alcohol serves in this material as a thermoplastic binder for 3D molding of the printed object with a passive function and is completely removed during sintering. The study presents the material, the process of fused deposition modeling (FDM) of CDHA scaffolds and its post-processing at three temperatures (1200, 1300, 1400 °C), as well it evaluates the cytotoxicity and biocompatibility of scaffolds with MTT and LDH release assays after 14 days. The study also includes a morphological evaluation of the cellular colonization with scanning electron microscopy (SEM) in two different filament orientations (rectilinear and gyroid). The results of the MTT assay showed that the tested material was not toxic, and cells were preserved in both orientations, with most cells present on the material fired at 1300°C. Results of the LDH release assay showed a slight increase in LDH leakage from all samples. Visual evaluation of SEM confirmed the ideal post-processing temperature of the 3D-printed FDM framework for samples fired at 1300°C and 1400°C, with a porosity of 0.3 mm between filaments. In conclusion, the presented fabrication and colonization of CDHA scaffolds have great potential to be used in the tissue engineering of bones.

This paper presents the results of laboratory tests of CFRP (carbon fibre-reinforced polymer) laminates, which allowed the development of numerical material models. The obtained data were used in a further stage to perform numerical simulations of four variants of medical tabletops differing, among other features, in the shape of the cross-section. Maximum deflections and effort in the composite material were analyzed. The final step was to perform a laboratory test for one of the tabletop versions, the results of which confirmed the correctness of the numerical calculations. This work is aimed at both researchers and designers involved in the practical application of fibre-reinforced polymer matrix composites.

This research explores the development of thermoplastic vulcanizate (TPV) blends derived from natural rubber (NR) and ethylene-butene copolymer (EBC) using a specific blend ratio and melt mixing technique. A comprehensive full factorial design of experiments (DOE) methodology is employed to optimize the processing parameters. TPVs are produced through dynamic vulcanization, combining rubber crosslinking and melt blending within a thermoplastic matrix under high temperatures and shear. The physico-mechanical properties of these TPVs are then analyzed. The objective is to enhance the mechanical performance by assessing the influence of blend ratio, mixing temperature, rotor speed, and mixing time on crucial properties, including tensile strength, elongation at break, compression set, tear strength, and hardness. Analysis of variance (ANOVA) identifies the optimal processing conditions that significantly improve material performance. Validation is achieved through atomic force microscopy (AFM), confirming the phase-separated structure and thus a success of dynamic vulcanization. Rubber process analyzer (RPA) and dynamic mechanical analyzer (DMA) assessments provide insights into the viscoelastic behavior and dynamic mechanical responses. Deconvolution analysis of temperature-dependent tanδ peaks reveals intricate microstructural interactions influencing the glass transition temperature (Tg). The optimized TPVs exhibit enhanced stiffness and effective energy dissipation capabilities across a wide temperature range, making them suitable for applications demanding thermal and mechanical load resistance. This study underscores the pivotal role of precise processing control in tailoring the properties of NR/EBC TPVs for specialized industrial uses. It highlights the indispensable contribution of the DOE methodology to TPV optimization, advancing material science and engineering, particularly for industries requiring robust and flexible materials.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

Abstract composite silver nanoparticles were synthesised using melanin broth and Arabic gum as a reducing and binding agent. The reactions are carried out with water because it is a non-hazardous solvent. The produced composites either had specified diameters (average diameter of 50 nm) with high silver loading or lower loading composites with tuneable morphologies and electrical properties. UV-IR, gamma, and conventional light are used to characterise the synthesised composite silver nanoparticles. Furthermore, measurements are carried out of the dielectric constant, refractive index, energy gap, optical and electrical conductivities, and refractive index coefficients. The silver nanoparticle formation was validated by UV-Vis measurement of the sample, which demonstrated a distinct peak at a wavelength of 420 nm. The characteristics of the composite silver nanoparticles are also quantified using several methods, including XRD, SEM, and particle size analysis.

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

A microstructure-based model is developed to study the effective anisotropic properties (magnetic, dielectric or thermal) of two phase particle-filled composites. The Green’s function technique and the effective field method are used to derive theoretically the homogenized (averaged) properties for a representative volume element containing isolated inclusion and an infinite, chain-structured particles. Those results are compared with the FE approximations conducted for the assumed representative volume element. In addition, as a special case, the Maxwell–Garnett model is retrieved when particle interactions are not taken into consideration. We shall also give some information on the optimal design of the effective anisotropic properties taking into account the shape of magnetic particles.

In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

The unique porous crystal structure of zeolite offers various important utilizations, it is one of the considerations in selecting zeolite at this study as component of composite for restraining noise. It so happens, previous experiments show that banana stem has porous structure, fibrous, high flexibility and can be applied as material for many various products including as component of acoustic material. The combination of both is alleged that it has capability in absorbing noise. This paper presents an investigation on the composite that it was synthesized of Activated Zeolite and Banana Stem Fibre in various weight for determining its sound absorption coefficient alpha (a). Activating natural zeolite was conducted by using 6M HCl in order for enlarging zeolite pores. The sound absorption coefficient was measured in the frequency range between 125 Hz up to 6000 Hz. The results show that the different weight of banana stem fibre as component of the synthesized composite affects the value of alpha and shifts the frequency area.

The excellent properties of carbon fibers, in combination with the high price of carbon fibers, makes it interesting to recycle these fibers. Pyrolysis is already an established recycling method to recover the carbon fibers, but in this process also the sizing is removed which could result in lower mechanical properties because of bad adhesion between the fiber and matrix. In this study, recycled carbon nonwoven reinforcements made from pyrolyzed carbon fibers were pre-treated in order to improve the mechanical properties of recycled carbon polyamide and recycled carbon polypropylene composites. The pre-treatment involves applying a to the matrix adapted primer coating to the nonwoven by spraying. Via compression molding, polyamide and polypropylene composites were prepared with and without pretreatment. The tensile and interlaminar shear strength of these composites were measured to determine the effect of the pretreatment. Results revealed that both strengths could be increased by pretreatment of the carbon nonwoven and the increase was largest for the PP composites.

In our study we investigated the additive manufacturing (AM) of ceramic-based Functionally Graded Materials (FGM) by the direct AM technology Thermoplastic 3D-Printing (T3DP). Zirconia components with a varying microstructure were additively manufactured by using thermoplastic suspensions with different contents of pore forming agents (PFA) and were co-sintered defect-free. Different materials were investigated concerning their suitability as PFA for the T3DP process. Different zirconia-based suspensions were prepared and used for AM of single- and multi-material test components. All samples were sintered defect-free and in the end we could realize a brick wall-like component consisting of dense (<1% porosity) and porous (approx. 5% porosity) zirconia areas to combine different properties in one component. The T3DP opens the door to AM of further ceramic-based 4D-components like multi-color or multi-material, especially multi-functional components.

We give a bilocal field theory description of a composite scalar with an extended binding potential, that reduces to the Nambu–Jona–Lasinio (NJL) model in the pointlike limit. This provides a description of the internal dynamics of the bound state and features a static internal wave-function, ϕ(⃗r), in the center-of-mass frame that satisfies a Schr¨odinger-Klein-Gordon equation with eigenvalues m2. We analyze the “coloron” model (single perturbative massive gluon exchange) which yields a UV completion of the NJL model. This has a BCS-like enhancement of its interaction, ∝ Nc the number of colors, and is classically critical with gcritical remarkably close to the NJL quantum critical coupling. Negative eigenvalues for m2 lead to spontaneous symmetry breaking, and the Yukawa coupling of the bound state to constituent fermions is emergent.

Premature failure and degradation of layers are the main problems for transportation infrastruc-ture. Addressing these issues necessitates implementing structural health monitoring (SHM) for transportation layers. This strategic approach is instrumental in mitigating maintenance expenses, prolonging the operational lifespan, and preventing accidents resulting from abrupt layer col-lapse. To this end, this research investigated the stress/strain and damage detection capabilities of a self-sensing cementitious composite developed for potential utilization in the construction of an intelligent subgrade layer. The prepared self-sensing cementitious composite consisted of 10% cement and hybrid conductive fillers, including multiwalled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) in sand. Initial findings reveal that the electrical resistivity of the composite is significantly affected by the concentration of MWCNTs/GNPs, with a minimum concentration of more than 0.5% needed to achieve a responsive cementitious composite. More-over, the piezoresistive analysis indicates that an increase in the concentration of MWCNTs/GNPs and stress levels leads to an improvement in the stress/strain sensing perfor-mance. When the self-sensing cementitious composite is subjected to equivalent stress levels, variations in the FCR exhibit an increasing trend with decreasing resilient modulus, stemming from a decrease in stiffness due to the increased concentration of MWCNTs/GNPs. Additionally, the EIS analysis demonstrates a contraction for the Nyquist curves under compressive ramp loading prior to failure, followed by the expansion of these curves postfailure. Scanning electron microscopy (SEM) images visually showcase the bridging effects of MWCNTs and the filling ef-fects of GNPs within the composite structure.

This study demonstrates the successful synthesis of Ni/Y2O3 nanocomposite particles through the application of ultrasound-assisted precipitation using the Ultrasonic Spray Pyrolysis technique. The particle size was predicted accurately using a modified equation, and they were collected in a water suspension with Polyvinylpyrrolidone (PVP) as the stabiliser. The presence of the Y2O3 core and Ni shell was confirmed with Transmission Electron Microscopy (TEM) and with electron diffraction. The TEM observations revealed the formation of round particles with an average diameter of 466 nm, while the lattice parameter on the Ni particle’s surface was measured to be 0.343 nm. The Ni/Y2O3 nanocomposite particle suspensions were lyophilized, to obtain a dried material that was suitable for embedding into a Polylactic acid (PLA) matrix. The resulting PLA/Ni/Y2O3 composite material was successfully extruded successfully, so that a 3D printed technology Fused Filament Fabrication could be used further for the production of tensile test tubes. The tensile tests showed that the addition of lyophilised Ni/Y2O3 into the PLA matrix decreased the tensile strength by 21.8 %, while the tensile modulus was not influenced. Dynamic Mechanical Analysis (DMA) showed that the addition of the Ni/Y2O3 particles increased the glass transition temperature by 5 °C, and increased the storage modulus in the glass transition range significantly. These findings demonstrate the potential for utilising Ni/Y2O3 nanocomposite particles in 3D printing applications, and warrant further exploration of their mechanical properties and potential applications in various fields.

Fluorescent hydrogels are promising candidate materials for portable biosensors to be used in point-of-care diagnosis because (1) they have a greater capacity for binding organic molecules than immunochromatographic test systems, determined by the immobilization of affinity labels within the three-dimensional hydrogel structure; (2) fluorescent detection is more sensitive than the colorimetric detection of gold nanoparticles or stained latex microparticles; (3) the properties of the gel matrix can be finely tuned for better compatibility and detection of different analytes; and (4) hydrogel biosensors can be made reusable and suitable for studying dynamic processes in real time. Water-soluble fluorescent nanocrystals are widely used for in vitro and in vivo biological imaging due to their unique optical properties, and hydrogels based on them allow preserving these properties in bulk composite macrostructures. Here we review the techniques for obtaining analyte-sensitive fluorescent hydrogels based on nanocrystals, the main methods used for detecting the fluorescent signal changes, and the approaches to the formation of inorganic fluorescent hydrogels via sol–gel phase transition using surface ligands of the nanocrystals.

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

Electrospinning polymer fibers for is a well-understood process, primarily resulting in random mats or single strands. More recent systems and methods have allowed for the production of nanofiber yarns (NFY) for ease of use in textiles. This paper presents a method of NFY manufacture using a simplified dry electrospinning system to produce self-assembling functional NFY capable of conducting electrical charge. The polymer is a mixture of cellulose nanocrystals (CNC), polyvinyl acrylate (PVA) and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). When treated with Ethylene Glycol (EG) to enhance conductivity, fibers touching the collector plate align to the applied electrostatic field and grow, twisting together as additional nanofiber polymer is added by the jet. The longer the electrospinning continues, the longer and more uniformly twisted the NFY becomes. This process has the added benefit of reducing the electric field required for NFY production from >2.43 kV cm-1 to 1.875 kV cm-1.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Air pollution is related to the development of people's livelihood. As one of the main pollutants in the air, formaldehyde affects people's physical and mental health. In order to remove formaldehyde and better protect the health of residents, it is very necessary to develop efficient adsorption materials. In this study, a cellulose composite aerogel Microcrystalline Cellulose/ N-(2- aminoethyl) -3- aminopropyl methyl dimethoxysilane (MCC/APMDS) modified by APMDS was explored. The pore volume and specific surface area of the modified aerogel decreased, the average pore diameter increased, and the adsorption capacity of formaldehyde was stronger. The adsorption experiment shows that the sample prepared under the conditions of APMDS dosage of 6 wt%, reaction time of 4 h and reaction temperature of 90℃ has the largest average pore size (14.56 nm) and the largest formaldehyde adsorption capacity (9.52 mg/g). The excellent adsorption of the composite aerogel is due to high porosity and rich active amino groups on the surface. This study provides valuable information for the preparation of adsorption materials with high formaldehyde adsorption capacity for air purification.

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

A deep relationship is identified between the Coulomb Force and Gravity. A gravitational constant for strong gravity is calculated from the relationship. The equivalence between mass and charge is explored. Implications are given for the expansion of Einstein's Field Equations to include vector gravity.

The accurate prediction of molecular properties such as lipophilicity and aqueous solubility are of great importance and pose challenges in several stages of the drug discovery pipeline. Machine learning methods like graph-based neural networks (GNNs) have shown exceptionally good performance in predicting these properties. In this work, we introduce a novel GNN architecture, called directed edge graph isomorphism network (D-GIN). It is composed of two distinct sub-architectures (D-MPNN, GIN) and achieves an improvement in accuracy over its sub-architectures employing various learning, and featurization strategies. We argue that combining models with different key aspects help make graph neural networks deeper and simultaneously increase their predictive power. Furthermore, we address current limitations in assessment of deep-learning models, namely, comparison of single training run performance metrics, and offer a more robust solution.

Typhoid fever is a major public health burden which causes substantial global morbidity and mortality due to lack of decisive diagnostic protocols. The capacity of commonly use diagnostic test to validate the absence of typhoid fever is controversial. This study explores to evaluate new techniques for typhoid diagnosis and proposed a harmonised suitable standardized composite reference to be adopted. Published peer-reviewed articles indexed in PubMed, MEDLINE and Google scholar were reviewed for hospital-based studies. This study reveals new typhoid diagnostic techniques such as proteomics, serology, Rapid Diagnostic tests (RDTs), transcriptomics, genomics, and metabolomics. 34.4% of the studies use prospective study design. The study result establishes that, Widal test has a moderate diagnostic accuracy with average percentage sensitivity (52.9%), specificity (54%), positive predictive value (PPV) (56.8%) as well as negative predictive value (NPV) (55.6%) when compared with 29.4%, 28%, 29.5%, and 27.8% of Typhidot respectively. The findings showed a statistically significant difference on the sensitivity between Widal and Typhidot t (40) = 2.639, p = 0.012 at p<0.05 using independent sample t-test. When there is no perfect reference standard that has an optimal diagnostic accuracy, the need for a harmonised suitable standardized composite reference is essential. Hence, this study recommends that, peripheral blood culture with established sensitivity of 60% and Widal test with average sensitivity of 52.9% be adopted as a consensus composite reference standard for typhoid fever diagnosis in other to improve confidence in prevalence estimates.

Modern day construction is widely influenced using concrete-steel composite columns. A lot of research on concrete-steel composite columns is being carried out around the world. The rapid growth in concrete-steel composite construction has widely decreased the use of conventional reinforced cement concrete construction (R.C.C), and the steel construction practices. The concrete-steel composite construction has obtained an extensive receiving around the globe. As Pakistan is a developing country, so, it is relatively a new concept for its construction industry when compared with the developed countries around the globe. Although, the R.C.C construction is suitable and economical for construction of framing systems of low-rise buildings, however, the increased dead load, span restrictions, less stiffness and risky formwork makes it uneconomical and unviable when it comes across the construction of intermediate to high-rise buildings. This research is an effort to learn the cost effectiveness, increased or decreased stiffness, and change on the functionality of the composite construction for intermediate to high-rise buildings constructed in Pakistan. A Base + Ground + 11 storey commercial building is selected for this study. A comparison is made between conventional R.C.C columns structure and concrete-encased composite columns structure. The equivalent static nonlinear analysis is performed using ETABS 2017 software. Although, for Base + Ground + 11 storey building, the construction cost of concrete-encased composite structure is 7.7% more than the conventional R.C.C columns structure, but the concrete-encased composite structure will have 13.013% more constructed floor area. This increased floor area helps to settle the cost difference between the two structures.

ZnS-CdS composite nano-powder doped with (0.01 mol %) Cobalt has been collected by a co-precipitation process at 300 K. The sample is characterized by structural, combined spectroscopic methods and magnetic studies. The prepared samples were belonging to cubic structure no impurity phases were observed. Doping of cobalt increase the neighborhood strain assessment and a decreases lattice constants decides from x-ray diffraction data. The crystallite size is 10.42nm. From UV-absorption and EPR studies revealed that the energy band gap of Co2+ doped ZnS-CdS composite nanopowder and extension of sp-d exchange interactions and common d-d transitions. The variation in the energy bandgap varies as a function of cobalt concentration is due to structural modification. Photoluminescence spectrum reveals the defect-related emissions and shows the formation of luminescence. FT-IR spectrum confirmed the feature vibrational manner of Zn, Cd, O–H and sulfide ions are in the host lattice. The doping-induced magnetic properties are studied by vibrating sample magnetometer which matches with the theoretical values besides ferromagnetic nature. Magnetic studies confirm the ferromagnetic nature of the material. Surface morphology and chemical homogeneity studies were carried out by using SEM with EDAX. Transmission electron microscope recommends the crystalline nature of nanoparticles, with average particle size is of the order of 20-100nm.

A galvalume corrugated sheet was utilized as formwork for a reinforced concrete beam in flexure. A numerical model was validated to the experimentally obtained data, and further adopted to simulate the behavior of this composite structure under elevated temperatures. The properties and constitutive stress-strain data of the basic materials were obtained from experiments, and superimposed into the finite element model. The study concluded that the load carrying capacity of the member decreased as a direct function on temperature increase, and the cracking moment was very sensitive to the temperature fluctuation. The elevated temperatures also altered the failure mode.

With the increased scientific interest in green technologies, many researches have been focused on the production of polymeric composites containing naturally occurring reinforcing particles. Apart from increasing mechanical properties, these additions can have a wide range of interesting effects, such as increasing the resistance to bacterial and fungal colonization. In this work, different amounts of two different natural products, namely neem and turmeric, have been added to polyethylene to act as a natural antibacterial and antifungal product for food packaging applications. Microscopic and spectroscopic characterization showed that fractions up to 5% of these products can be dispersed into low-molecular weight polyethylene, while higher amounts could not be properly dispersed and resulted in an inhomogeneous, fragile composite. In vitro testing conducted with Escherichia coli, Staphylococcus aureus and Candida albicans showed a reduced proliferation of pathogens when compared to the polyethylene references. In particular, turmeric, resulted to be more effective against E. coli when compared to neem, while they had similar performances against S. aureus. Against C. albicans, only neem was able to show a good antifungal behavior, at high concentrations. Tensile testing showed that the addition of reinforcing particles reduces the mechanical properties of polyethylene, and, in the case of turmeric, it is further reduced by UV irradiation.

Composite membranes formed by sulfonated poly(ether ether ketone) (SPEEK) with embedded carbon quantum dots (CQDs) were used for detection and removal of heavy metal ions, such as lead and cadmium, from water. SPEEK is responsible for the capture of heavy metals based on the cation exchange mechanism, while CQDs detect their contamination by exhibiting changes in fluorescence. Water-insoluble “red” carbon quantum dots (rCQDs) were synthesized from p-phenylenediamine so that their photoluminescence was shifted from that of the polymer matrix. CQDs and the composites were characterized by several techniques: FTIR, Raman, UV/VIS, photoluminescence, XPS spectroscopies and AFM microscopy. The heavy metal ion concentration was analyzed by inductively coupled plasma–optical emission spectroscopy (ICP-OES). The concentration ranges were 10.8 - 0.1 mM for Pb2+ and 10.0 - 0.27 mM for Cd2+. The composite achieved 100% removal efficiency for lead and cadmium if the concentration was below a half of the ion exchange capacity of SPEEK. The regeneration of membranes in 1 M NaCl was also studied. SPEEK/rCQDs showed a turn-off effect more pronounced for lead. A second order law was effective to describe the kinetics of the process.

Steel construction is used more often these days as an alternative to the R.C.C. when light weight, high strength, large-span structures with a faster erection are required. Extensive studies have been done by researchers to study the seismic performance of reinforced concrete and steel structures, both in terms of elastic and inelastic behavior. Composite construction is also a recent advancement in the building industry with similar advantages. However, no emphasis has been given to the comparison between the inelastic behavior of steel and composite structures when subjected to lateral loads. This study compares the inelastic behavior of steel and a composite frame designed to have the same plastic moment capacity for structural members. The responses, such as the formation of hinges, story drifts, story displacements, lateral stiffness, ductility, maximum strength, energy dissipated, joint accelerations, and performance points, are compared with the aid of the building analysis and design software ETABS-18. For this, response spectrum analysis, pushover analysis and nonlinear direct integration time history analysis have been performed on both frames. For design and analysis, international codes such as IS 800-2007, IS 875 (Part I, II, IV), IS 1893-2002, AISC 360 (16 &amp; 10) and FEMA 440 have been used. Part of this study also aims at comparing the response of these frames when subjected to near field and far field earthquakes. It can be concluded from the results that the post yield performance of the composite frame is superior to that of the steel frame when seismically excited.

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.

In the present study, the corrosion resistance of amorphous coating and composite coatings in 3.5 wt.% NaCl, 0.5 M H₂SO₄ and 10 wt.% NaOH solution were studied. The composite coatings exhibit superior corrosion resistance. When the content of AT13 （Al₂O₃–13 wt.% TiO₂）was 15 wt.%, the composite coating has the lowest corrosion current density (1.75×10^-6 A cm^-2), which is 5.14×10^-5 A cm^-2 for Fe-based metallic glassy coating, and the highest corrosion potential (-411 mV), which is -580 mV for Fe-based metallic glassy coating. The breakdown potential of the passivation film in 3.5 wt.% NaCl solution was much higher than that of 316L.The long-time immersion corrosion tests carried out on different coatings showed that the corrosion protection effect of coating was enhanced with the increase of the amount of AT13 added.

Butyl rubber-based composite (BRC) is one of the most popular materials for the fabrication of protective glove against chemical and mechanical risks. However, in many working places such as metal manufacturing or automotive mechanical services, its mechanical hazards usually appear together with metalworking fluids (MWFs). The presence of these contaminants, particularly at high temperature, could modify its properties due to the scission, the plasticization, the crosslinking of polymer network and thus led to severe modification of mechanical and physicochemical properties of material. This work aims to determine the effect of temperature and a metalworking fluid on mechanical behavior of butyl rubber composite dealing with crosslinking density, cohesion forces and elastic constant of BRC on the based on Mooney-Rivlin’s theory. The effect of temperature with and without MWFs on thermo dynamical properties and morphology of butyl membranes is also investigated. The prediction of service lifetime is then evaluated from extrapolation of Arrhenius plot at different temperatures.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

Introduction: To indentify the most effective actors(authors, countries, and journals) about composite resin restorations in the period 2000-2020.Material and Methods: An electronis research was conducted in the Scopus database by selecting the words ‘composite resin’ and ‘restoration and English language, article and review types, dentistry field. Their bibliometric data including publication title, authorship, citation count, citation dentistry, year of publication, country and institution of origin, journal of publication, study design, and keywords were extracted and analyzed.Results and Discussion: To our knowledge, this is the first bibliometric article on composite resin restorations. This study provides information about authors, institutions and countries that contribute to significant improvements in composite resin restorations. From 2000 to 2020, there were 7118 articles published from 99 countries.Articles originate primarily from the USA and Brazil. Results indicate that the USA, Brazil, Germany, Turkey, the United Kingdom, Japan, Swtizerland, Italy, Netherlands and India are the leading countries in composite resin restoration research and account for 51.8% of the total number of publications. The total number of citations are 158.404, corresponding to 22 citations per paper publication. During the time period examined, 776 hot articles and 228 classic articles on composite resin restorations were found.The journal with the most publications is ‘Operative Dentistry’. The publishing houses of the top 10 journals are from 4 countries: USA(6),Netherlands(2),Germany(1),Japan(1). The most cited article within the boundaires of this study is Ferracane’s article titled ‘Resin composite-State of the art’, which was published in Dental Materials in 2011 and received 913 citations.

This work investigated the influence of current density, plating solution flow rate, and nozzle outlet-cathode distance on the properties of Ni-diamond composite coatings. A multi-physics field simulation is employed to analyze the interplay between current density, plating solution flow rate, and nozzle outlet-cathode distance on the flow field and electric field distribution. Additionally, particle tracing simulations were incorporated into the model to evaluate the incorporation efficiency of diamond particles during composite electrodeposition. Experimental validation of the findings shows a significant increase in the diamond particle content of the coating. This combined approach provides valuable insights for optimizing the jet electrodeposition process for Ni-diamond composite coatings with superior properties.

Self-healing materials research spans many academic disciplines and employs a wide range of methodologies. Some of the developed concepts are driven by the direct application of the materials. However, a deeper understanding of the basic mechanisms and principles of self-healing materials is still a challenging aim. Nature has mostly served as an inspiration for the development of new self-healing materials, and it will undoubtedly continue to be a significant source of inspiration for the creation of novel ideas. This review encompasses the principles of self-healing mechanisms based on the concepts of autonomous and non-autonomous procedures. Studies based on smart composite materials with autonomous self-healing properties are also included and discussed from two aspects of intrinsic or extrinsic abilities, taking into consideration their components and structures as well as the design of these composites. Finally, special attention is given to the application of the materials in several fields such as aerospace, automotive, marine, energy, medical and healthcare, military, and construction.

The current study aims to develop a methodology for obtaining topology-optimal structures made of short fiber-reinforced polymers, which include the fluid-structure interaction. Accounting for the molding process during the internal iterations of topology optimization makes it possible to enhance the weight efficiency of structures—a crucial aspect, especially in aerospace. Anisotropy is considered through the fiber orientation tensor, which is modeled by solving the plastic molding equations for non-Newtonian fluids, and then introduced as a variable of the stiffness matrix during the structural analysis. The materials used were non-linearly modeled using an exponential-and-linear hardening law. The evaluation of weight efficiency in structures composed of short-reinforced composite materials using a dimensionless criterion is addressed. Experimental verification was performed to confirm the validity of the developed methodology. The evidence illustrates that considering anisotropy leads to stiffer structures and structural elements should be oriented in the direction of maximal stiffness. The load-carrying factor can be expressed in terms of failure criteria. The presented multidisciplinary methodology can be used to improve the quality of the design of structures made of short fiber-reinforced composites (SFRC) where high stiffness, high strength, and minimum mass are the primary required structural characteristics.

Although the Orthotropic steel decks (OSDs) have been widely used in the construction of long-span bridges, there are frequently reported fatigue cracks after years of operation, and the bridge deck overlay also presents severe damage due to OSD crack-induced stiffness reduction. The ultra-high performance concrete (UHPC), recognized as the most innovative cementitious composites and the next generation of high-performance materials, shows high strength, ductility, toughness and well performance on durability. After its first application to the OSD bridge in early 2000s, the orthotropic Steel-UHPC composite deck has been comprehensively studied worldwide. This review will summarize some important studies and findings on behavior and fatigue performance of orthotropic steel-UHPC composite deck. The existing studies and engineering application indicate that such deck system presents good bending behavior and high fatigue performance. The failure mode of shear studs in UHPC layer is dominated by shear fractures. The cracking of UHPC layer shall consider the superposition effect of stress from both the whole bridge structure and local decks. While some reasonable structural details in the traditional OSD may not work for the orthotropic steel-UHPC composite deck. It is recommended to evaluate the stress behavior and structural parameters, as well as fatigue life by conducting the field test under in-service traffic conditions.

The analysis and measurement of poverty is a crucial issue in the field of social science. Poverty is a multidimensional notion that can be measured using composite indicators relevant to synthesizing statistical indicators. Subjective choices could, however, affect these indicators. We propose interval-based composite indicators to avoid the problem, enabling us in this context to obtain robust and reliable measures. Based on a relevant conceptual model of poverty we have identified, we will consider all the various factors identified. Then, considering a different random configuration of the various factors, we will compute a different composite indicator. We can obtain a different interval for each region based on the distinct factor choices on the different assumptions for constructing the composite indicator. So we will create an interval-based composite indicator based on the results obtained by the Monte-Carlo simulation of all the different assumptions. The different intervals can be compared, and various rankings for poverty can be obtained. For their parameters, such as center, minimum, maximum, and range, the poverty interval composite indicator can be considered and compared. The results demonstrate a relevant and consistent measurement of the indicator and the shadow sector's relevant impact on the final measures.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

The effects of carbon fiber hybridisation on the thermal properties of woven kenaf reinforced epoxy composites kenaf fibre were studied. Woven kenaf hybrid composites at the different weave designs of plain and satin, and fabric count of 5 × 5 and 6 × 6 were manually prepared by vacuum infusion technique. Thermal properties of pure carbon fibre and hybrid composites were conducted by using thermogravimetric analyser (TGA) and differential scanning calorimeter (DSC). It was found that at high kenaf fibre content showed better thermal stability while the highest thermally stable was found in pure carbon fibre composite. The TG and DTG results showed that the amount of residue decreased in plain-designed hybrid composite compared to satin-designed hybrid composite. The DSC data revealed that the presence of woven kenaf increase decomposition temperature.

A lightweight composite bridge deck system composed of steel orthotropic deck stiffened with thin Ultra-High Performance Concrete (UHPC) layer is developed to eliminate fatigue cracks in orthotropic steel decks. During the construction and operation period of the bridge, the debonding between the steel deck and the UHPC layer may introduce the several issues, such as crack-induced water invasion and distinct reduction of the shear resistance. In the study, an effective and novel non-destructive interface condition monitoring approach using piezoelectric lead zirconate titanate (PZT)-based technologies is proposed to detect interfacial delamination between steel deck and UHPC layer. Experimental tests are performed on several steel-UHPC composite slabs and a conventional steel-concrete composite slab. The thin styrofoam sheets with different sizes and thicknesses are set on different locations of the steel deck as the artificial debondings. The PZT ceramic patches are bonded on the surfaces of the steel deck and UHPC layer as the actuators/sensors. An improved PSO (Particle Swarm Optimization)-K-means clustering algorithms is proposed to obtain the debonding patterns based on the feature data set. The laboratory tests demonstrate that the proposed approach provides an effective and accurate way to detect interfacial debonding of steel-UHPC composite slab.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

We developed some questions regarding twin prime conjecture by examining the bounded gaps between composite numbers and explained the relations between the formulas regarding composite numbers. Then we proved the twin prime conjecture to answer the new questions raised by proving the expression: \[ \liminf_{n\to\infty} (c_n_+_1 - c_n) \ge 10. \] In addition, we prove many different approaches have been and it has been proved that there must be a twin prime in the range $(p_k_2\cdot p_k_1, p^2_k_1)$, where $p \neq 2$.

To address the challenges associated with the difficult electromagnetic (EM) scattering computations of anisotropic dielectric-coated metallic composite targets, we proposed an efficient hybrid algorithm for simulating the EM scattering of complex targets with anisotropic dielectric coatings. This method, based on Impedance Boundary Condition (IBC), utilizes surface impedance vectors to describe the EM properties of the dielectric. It fully leverages the respective advantages of the low-frequency Method of Moments (MoM) and the high-frequency Physical Optics (PO) to achieve high-precision and rapid EM simulation of anisotropic dielectric-coated metallic composite targets. Employing boundary conditions and equivalent principles, we equivalently transform the EM scattering problem of targets with thin dielectric coatings into the radiation problem of equivalent EM current on impedance surfaces. This enables the high-precision and rapid calculation of Radar Cross Sections (RCS) for complex targets with anisotropic dielectric coatings. Using examples such as a square plate structure, a simplified aircraft, and a complex satellite model, the simulation results exhibit a high degree of agreement with full-wave numerical solutions and demonstrate a significant advantage in computational resources. This research convincingly demonstrates the accuracy and effectiveness of the proposed method.

Development of high nutritious bakery products with optimum utilization of food waste is a major challenge for food industries. Food waste is major challenge in an each country. The optimum utilization of food waste for sustainable development goal of country is important ant for growth of the nation. The aim of the present work is to prepare value-added composite flour mixed bread from wastes of fruit and vegetables. The composite flour was prepared in four formulations of Peel and Pomace Wheat Flour (PPWF), as PPWF1, PPWF2, PPWF3 and PPWF4. Compositing flour was blended by a mix of vegetable and fruits pomace powders and whole wheat flour. Indian gooseberry pomace powder, apple pomace powder, bottle gourd peel powder, and potato peel powder were used with whole wheat flour to make pomace and whole wheat flour compositions as PPWF1, PPWF2, PPWF3 and PPWF4. Broadly this work was divided into three phases, first phase has conducted nutritional and functional analysis on peel and pomace powders individually, which shows the significance of using them for our research work. The second phase works in the creation of composite flours with different composition ratios as discussed above as PPWF. This phase shows the nutritional and functional analysis of four composite flours. Out of these four flours, PPWF3 contained a good amount of fiber 8.16%, crude protein 3.18%, total phenolic content 14.48%, moisture 9.5%, vitamin C 13.64mg/100g, and total phenolic compound 14.48(mg/GAE/g) which are maximum and acceptable range values as compared to other three composite flours and the wheat flour-control group flour. Then in the third phase, the PPWF3 is used as a partial replacement ratio of wheat flour in wheat flour due to its high phenolic content, Vitamin C, and the richness of fibers. This composite flour is used to make bread dough, two samples G1 and G2 are made; out of which G2 offers better nutritional, functional, and sensory evaluations in comparison with refined wheat four bread is taken as a control group. Thus, such utilization of food wastes in bread making can generate a value of wastes and can improve nutritional attributes of bread, which may improve an individual’s health.

Shear deflection effects are traditionally neglected in most structural system identification methods. Unfortunately, this assumption might lead to significant errors in some structures, like deep beams. Although some inverse analysis methods based on the stiffness matrix method including shear deformation effects have been presented in the literature, none of these methods is able to deal with actual rotations in their formulations. Recently, the observability techniques, one of the first methods for the inverse analysis of structures included the shear effects into the system of equations. In this approach, the effects of shear rotation are neglected. When actual rotations on site are used to estimate the mechanical properties in the inverse analysis, it can result in serious errors in the observed properties. This characteristic might be especially problematic in structures such as deep beams where only rotations can be measured. To solve this problem and increase the observability techniques' applicability, this paper proposes a new approach to include shear rotations into the inverse analysis by observability techniques. This modification is based on the introduction of a new iterative process. To illustrate the applicability and potential of the proposed method, the inverse analysis of several examples of growing complexity is presented.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

This paper discusses a possible approach to validate the Goldbach conjucture which states that all even numbers can be expressed as a summation of two prime numbers. For this purpose the paper begins with the concept of successive-addition-of-digits-of-an-integer-number (SADN) and its properties in terms of basic algebraic functions like addition, multiplication and subtraction. This concept of SADN forms the basis for classifying all odd numbers into 3 series- the S1, S3 and S5 series- which comprise of odd numbers of SADN(7,4,1), SADN(3,9,6) and SADN(5,2,8) respectively and follow a cyclical order. The S1 and S5 series are of interest in the analysis since they include both prime and composite numbers while the S3 series exclusively consists of composite numbers. Furthermore, the multiplicative property of SADN shows why composites on the S1 series are derived as products of intra-series elements of the S1 and S5 series while composites on the S5 series are derived as products of inter-series elements of the S1 and S5 series. The role of SADN is also important in determining the relevant series for identifying the combination of primes for a given even number since it shows why such combinations for even numbers of SADN(1,4,7) will be found on the S5 series while those for even numbers of SADN(2,5,8) will lie on the S1 series and both the series have a role to play in identifying the prime number combinations for even numbers with SADN(3,6,9). Thereafter, the analysis moves to calculating the total number of acceptable combinations for a given even number that would include combinations in the nature of two composites (c1+c2), one prime and one composite (p+c) and two primes (p1+p2). A cyclical pattern followed by even numbers is also discussed in this context. Identifying the c1+c2 and p+c combinations and thereafter subtracting them from the total number of combinations will yield the number of p1+p2 combinations. For this purpose the paper discusses a general method to calculate the number of composites on the S1 and S5 series for a given number and provides a detailed method for deriving the number of c1+c2 combinations. The paper presents this analysis as a proof to validate the Goldbach conjecture. Since even numbers can be of SADN 1 to 9 and the relation between nTc (i.e. total number of acceptable combinations) and nc(i.e. number of composites) for all even numbers can either be of nTc > nc or nTc ≤ nc, the paper shows that the Goldbach conjecture is true for both these categories of even numbers. In this manner this analysis is totally inclusive of all even numbers in general terms and since the analysis of every even number is common in methodology but unique in compilation, apart from being totally inclusive, it is also mutually exclusive in nature. This proves that the Goldbach conjecture which states that all even numbers can be expressed as atleast one combination of two prime numbers holds true for all even numbers, across all categories possible. Additionally this approach proves that the identification of p1+p2 combinations which would validate the Goldbach conjecture lies in the identification of c1+c2 combinations.

The thermal properties of novel nanomaterials play a significant role in determining the performance of the material in technological applications. Herein, direct measurement of the temperature diffusivity of cellulose nanocomposite films was carried out by the micro-contact method. Polymer films containing up to 2%wt. of nanocellulose were synthesised by a simple chemical process. Films of a high optical transmittance T ≈ 80 % (for a 200- μ m-thick film), which were up to 44% crystalline, were characterised. Two different modalities of temperature diffusivity based on: 1) a resistance change and 2) micro-thermocouple detected modulation of a heat wave, were used for the polymer films with cross-sections of ∼ 100 μ m thickness. Twice different in-plane α ‖ and out-of-plane α ⊥ temperature diffusivities were directly determined with high fidelity: α ‖ = 2 . 12 × 10 − 7 m 2 /s and α ⊥ = 1 . 13 × 10 − 7 m 2 /s. An amorphous polyethylene terephthalate (PET) fiber was measured for comparison α ‖ = 1 . 15 × 10 − 7 m 2 /s. This work provides an example of a direct contact measurement of thermal properties of nanocellulose composite films. The thermal diffusivity, which is usually high in strongly interconnected networks and crystals, was investigated for the first time in this composite.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

In this paper we obtain some inequalities of Hermite-Hadamard type for composite convex functions. Applications for AG, AH-convex functions, GA, GG, GH-convex functions and HA, HG, HH-convex function are given. Applications for p, r-convex and LogExp functions are presented as well.

The processing of cloud free geo-referenced imagery is one of the preliminary processing step of any land application. This letter describe the methodology developed to obtain a seamless cloud free composite of Africa for 2016 using Sentinel-2A data at 10 meters resolution freely available from the European Space Agency. The method is based on an hybrid method resulting from the merging of the two most robust time series methods namely the "darkest pixel" and the "maximum NDVI" previously developed with AVHRR time series.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

This research is mainly focused on the evaluation of TiO2/Fe2O3 composite and two industrial types of waste (kaolin (Clay-K) and a blast furnace sludge (BFS)) as adsorbent materials of cyanide and as photocatalysts. First, adsorption tests were performed in the absence of light. During photodegradation experiments, the effect of the type of irradiation (ultraviolet (UV) light), visible light and natural sunlight), irradiation time, the type of photocatalyst, as well as irradiance in case of natural sunlight use, were investigated. Adsorption results indicate that Clay-K and TiO2/Fe2O3 materials adsorb approximately twice as much cyanide compared to the BFS sample, which only adsorbs 33.3% (124.87 mg/g); this is due to its smaller specific surface area (5.69 m2/g) compared to that of the other two materials (Clay-K and TiO2/Fe2O3 (14.93 m2/g and 66.59 m2/g, respectively). The results obtained from the study of photodegradation of cyanide under UV irradiation, indicate that Clay-K and BFS samples photodegrade cyanide by 96.44% and 92.66%, respectively. On the other hand, using UV irradiation plus solar irradiation and visible plus solar irradiation, the best photocatalyst was the TiO2/Fe2O3, with 98.66% photodegradation. The use of natural sunlight (irradiance of 600 to 800 W/m2) of a NaCN solution of 750 mg/L, the BFS material was the most efficient to photodegrade cyanide, obtaining 97% in two hours and 87% in just 30 minutes of irradiation.

In the present paper, Co-B/SiC composite coatings were obtained via electrodeposition from colloidal suspensions with different concentrations of SiC particles and subsequent heat treatments at 350 °C. The composition, morphology and structure of the Co-B/SiC composite coatings were analyzed using glow discharge spectrometry (GDS), scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Hardness and tribological properties were also studied. The results showed that an increase in the SiC concentration in the colloidal suspensions resulted in both an increase in the SiC content and a decrease in the B content in the obtained Co-B/SiC coatings. The Co-B/SiC coatings were adherent, glossy and soft and exhibited a homogeneous composition in all thicknesses. By contrast, an increase in the SiC particle content of the Co-B/SiC composite coating from 0 to 2.56 at.% SiC reduced the hardness of the film from 680 to 360 HV and decreased the wear volume values from 1180 to 23 mm³ N^-1 m^-1, respectively (that is, the wear resistance increased). Moreover, when the Co-B/SiC coatings with SiC content ranging from 0 to 2.56 at.% SiC were subjected to a heat treatment process, the obtained coating hardness values were in the range of 1200 to 1500 HV and the wear volume values were in the range of 382 to 19 mm³ N^-1 m^-1.

People wore clothes for warmth, survival and necessity in modern life as well but in modern era, eco-friendliness, shorten production time, design, and intelligence also matters. The seamless bonding technology strengthen the bond between fabrics in textiles, while Grey relational analysis (GRA) can be applied to fabrics to measure the relationship between data series and determine the closeness of each data series. In this study, polyurethane prepolymer, 2-Hydroxyethyl acrylate (2-HEA) as an end-capping agent, and n-octyl acrylate (ODA) as a photo-initiator were used to synthesize dual-curing polyurethane hot-melt adhesive. The Taguchi quality engineering and grey relational analysis used to discuss the influence of different mole ratio of NCO:OH, and the effect of the molar ratio of addition of octyl decyl acrylate on the mechanical strength. The Fourier transform infrared spectroscopy (FTIR) results showed the termination of prepolymer's polymerization reaction and the C=O peak intensity at 1730 cm-1 indicating the efficient bonding to main chain. The high molecular weight polymer (20,000-30,000) described by advanced polymer chromatography (APC) confirmed the polyurethane polymer bonded with octyl decyl acrylate to achieve the photo-thermosetting effect. The thermogravimetric analysis (TGA) results showed the thermal decomposition temperature of polyurethane hot melt adhesive also increased and highest pyrolysis temperature (349.89℃) for the polyhydric alcohols. The high value of shear strength (34.94 kg/cm2) as well as peel strength (1.68 kg/cm) were also observed in dual-cure photo-thermosetting polyurethane hot melt adhesive. The signal-to-noise ratio also used to generate the grey relational degree. It was observed that the best parameter ration of NCO: OH was 4:1 with 5 moles of monomer. The Taguchi quality engineering method was used to find the parameters of single quality optimization, and then the grey relation calculation was used to obtain the parameter combination of multi-quality optimization for thermosetting polyurethane hot melt adhesive. The study aims to meet the requirements of seamless bonding in textile factories and optimized experimental parameter design by setting target values can effectively increase production speed, reduce processing time and costs as well.