A heat transfer model, has determined millimeter crude oil thicknesses on saltwater at night. Model inputs are calibrated thermographic imagery, weather station data, metrological observations, and crude oil thermal conductivity. Outdoor field-testing was performed at the National Oil Spill Response & Renewable Energy Test Facility (Ohmsett) to determine model accuracy. Alaskan North Slope (ANS), Hoover Offshore Oil Pipeline System Blend (HOOPS), and ROCK crude oils were placed at varying mm depths. A roof-top mounted thermal camera measured the average oil surface temperature for each target and converted to oil spill thickness. The fidelity of the thickness measurements is dependent on the accurate measurement of the atmospheric and weather parameters, sea state, heat transfer constants, crude oil evaporation rates, and calibration and stability of the thermal camera.

Toshiba devised the bladeless fan (or Air Multiplier) concept in 1981. Researchers like James Dyson and Jafari et al. further developed it. Bladeless fans are more energy-efficient, safer due to the hidden blades, easier to clean, and more adjustable than conventional fans. From a performance point of view, bladeless fans are better because they multiply mass flow rate, eliminate buffeting, consume less power, and are quieter. This paper investigates the influence of the airfoil’s outlet slit thickness on the discharge ratio by varying the outlet slit thickness of an Eppler 473 airfoil from 1.2 mm to 2 mm in intervals of 0.2 mm. Results indicated that smaller slits showed higher discharge ratios. The airfoil with a 1.2 mm slit thickness showed a discharge ratio of 18.78, a 24% increase from the discharge ratio of the 2 mm slit. The effect of outlet angle on the pressure drop across the airfoil was also studied. Outlet angles were varied from 16∘ to 26∘ by an interval of 2∘. The airfoil profile with a 24∘ outlet angle showed a maximum pressure difference of 965 Pa between the slit and leading edge. In contrast, the 16∘ outlet angle showed the least pressure difference of 355 Pa. Parameters such as average velocity, turbulent kinetic energy, the standard deviation of velocity and outlet velocity magnitude was used to assess the performance of airfoil profiles used in bladeless fan.

The successful handling of large semiconductor wafers is crucial for scaling up their production. Early-stage warpage control allows to prevent undesirable asymmetric warpage, known as wafer bifurcation or buckling. Indeed, even in a gravity-free environment, thinning an 8" or 12" semiconductor wafer can result in warpage and bifurcation. To mitigate this issue, the taiko method, which involves creating a thicker ring region around the rim of the wafer, has been widely used. Previous research has focused on the theoretical factors affecting the warpage of a backside metalized taiko wafer. This work extends the case to a front-side metalized taiko wafer and introduces the concept of the equivalent thickness of a taiko wafer. The equivalent thickness of a taiko wafer, influenced by the ring region, lies in between the thickness of the central region and that of the annular region. Because of the limited number of taiko wafers that can be produced on a production line, modelling can be beneficial. In this work we compared the results of a developed analytical model with those obtained from a finite element analysis (FEA) approach with ANSYSY® software to model the equivalent thickness of a taiko wafer. We investigated the curvature as a function of the stress of the metal layer, considering key design factors such as the substrate region thickness, the thickness of the thin metal film, the step height, and the width of the ring region. By systematically varying the thickness of the central region of the taiko wafer, we explored the curvature as a function of stress induced by thermal load in the linear regime and determined the slopes in the linear region of the curvature vs. stress curves. The aim of this study is to identify regularities and similarities with the Stoney equation and investigate the validity of the analytical approach for the case of a taiko substrate. It results that there is a good agreement between the analytical model of a taiko wafer and the numerical analysis gained by the FEA methods.

X-ray fluorescence is largely employed in the measurement of the thickness of coatings. Despite of its diffusion, the task is not straightforward because of the complex physics involved that results in high dependence on matrix effects. Thickness quantification is in practice accomplished using the Fundamental Parameters approach, adjusted with empirical measurements of standards with known composition and thickness. This approach has two major drawbacks: i) there are no standards for any possible coating and coating architecture and ii) even relying on standards, the quantification of unknown samples requires the precise knowledge of the matrix nature (e.g., in case of multilayer coatings the thickness and the composition of each underlayer). In this work, we describe a semiquantitative approach to coatings thickness measurement based on the construction of calibration curves through simulated XRF spectra built with Monte Carlo simulations. Simulations have been performed with the freeware software XMI-MSIM. We have assessed the accuracy of the methods by comparing the results with those obtained by i) XRF thickness determination with standards and ii) FIB-SEM cross-sectioning. Then we evaluated which parameters are critical in this kind of indirect thickness measurements.

Nuclear magnetic resonance (NMR) is a technique used for many years by chemists for elucidation of molecular structure. Technological progress over the years has enabled this technique, making it easier to use. Thus, the LF-NMR (low-field NMR) was introduced as side technique, characterized by low man-agement costs and shorter analysis time than its main counterpart. The application of 1H LF-NMR for the quantification of ethyl alcohol in different alcoholic matrices is herein described, comparing results ob-tained with this technique with those determined by a reference gascromatographic method.

BACKGROUND Detecting total cholesterol in dried blood spots could aid in identifying individuals with a high likelihood of familial hypercholesterolemia and could be used as a screening measure. This study aims to assess the diagnostic accuracy of dried blood spots on Whatman 903 paper cards using a manual enzymatic technique. METHODS A total of 394 samples collected as serum and dried blood spots were compared. Cholesterol was determined in serum using the automated reference method, while cholesterol on paper was measured using a manual enzymatic method. Within- and between-day diagnostic variability were analyzed. The correlation between both methods was assessed using Passing-Bablok regression and Bland-Altman plot. Internal validation of our correlation formula was performed on 149 samples, along with external validation of the formula proposed by Corso et al. RESULTS The within- and between-day coefficient of variation was found to be lower than 10.14% and 14.09%, respectively. Method comparison yielded an area under the curve of 0.976, with a standard error of 0.009. Passing-Bablok regression indicated a precision of 0.803 and an accuracy of 0.96. Internal validation precision was measured at 0.716. Regarding internal validation, calculated cholesterol with our regression line did not differ from serum cholesterol analysis, while significant differences were observed in calculated cholesterol levels using the external formula. CONCLUSIONS Total cholesterol analysis in dot blood spots demonstrates high precision and reproducibility. This method reliably enables the incorporation of this biological marker into neonatal screening for familial hypercholesterolemia detection.

The ubiquitous presence of microplastics (MPs) in the environment poses a threat to ecosystems and increases concerns about their exposure to the human body. However, despite being consumed for health improvement, limited research has been conducted on MPs in functional foods. This study aimed to investigate the occurrence of MPs and the relation of the source of raw material or the manufacture in various omega-3 oil in the Korean market. MPs in omega-3 capsule and raw oil, sourced from both plant-based (PB) and animal-based (AB) sources, were investigated. We developed the method by direct filtration with acetone washing and analyzed MPs greater than 5 μm using microscope-Raman spectroscopy. The average number of MPs was found to be 1.2 ± 1.7 MPs/g for PB raw oil, 2.2 ± 1.7 MPs/g for AB raw oil, 3.5 ± 3.9 MPs/g for PB capsule oil, and 10.6 ± 8.9 MPs/g for AB capsule oil. Polypropylene and polyethylene terephthalate were major specious (83-95 %) found in omega-3 oil. The ratio of size range remained consistent across all groups, with a trend of higher detection rates as the size diminished. The results reveal that the main reason of MPs contamination is not the source of raw material but the manufacturing and packaging process for omega-3 oil.

The purpose of the present study was to examine the relationships between bat swing speed (BSS) and muscle thickness and lateral asymmetry of the trunk and limbs in collegiate baseball players. Twenty-four collegiate baseball players participated in this study. The maximum BSS in hitting a teed ball was measured using a motion capture system. The muscle thicknesses of the trunk (upper abdominal rectus, central abdominal rectus, lower abdominal rectus, abdominal wall, and multifidus lumborum), upper limb, and lower limb were measured using a B-mode ultrasonography. Lateral asymmetry between each pair of muscles was determined as the ratio of the thickness of the dominant side to that of the non-dominant side. Significant positive correlations were observed between BSS and muscle thicknesses of the abdominal wall and multifidus lumborum on the dominant side (r = 0.426 and 0.431, respectively; p < 0.05), while nearly significant positive correlations were observed between BSS and muscle thicknesses on the non-dominant side. No significant correlations were found between BSS and lateral asymmetry of all muscles. These findings indicate the importance of the trunk muscles for bat swing, and the lack of association between BSS and lateral asymmetry of muscle size.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

Essential oils (EOs) have been gaining popularity in the past decades among researchers due to their potential to replace conventional chemicals used in the fight against pests, pathogenic and spoilage microbes and oxidation processes. EOs are complex mixtures with many chemical components the content of which depends on many factors – not just the plant genus, species or subspecies, but also chemotype, locality and climatic conditions, phase of vegetation, method of extraction and others. Due to this fact, there’s still much to study, with antimicrobial effect being one of the key properties of EOs. There are many methods that have been frequently engaged by researchers for in vitro evaluation; however, although the research has been going on for decades, an internationally accepted standard is still missing. Most of methods are based on time-proven standards used for testing of antibiotics. Due to the specific properties of EOs and their components, such as volatility and hydrophobicity, many modifications of these standard procedures have been adopted. The aim of this review is to describe the most common methods and their modifications for testing of antimicrobial properties of EOs and to point out the most controversial variables which can potentially affect results of the assays.

We aimed to determine whether A-mode ultrasound (US) can provide accurate and reliable measurements comparable to those obtained through B-mode US, under diverse conditions. Thirty healthy participants (15 female, 15 male) underwent measurements of subcutaneous fat thickness (SFT), muscle thickness (MT), and muscle quality (MQ) in the trapezius and biceps brachii muscle with both US modes after and before exercises designed to stimulate the respec-tive muscles. In three key indices, the results demonstrated high validity of A-mode, with min-imal mean differences between the two devices less than 0.91mm and intraclass correlation coef-ficients exceeding 0.95 at all measures. Also, Correlation coefficients between error scores and average scores for the trapezius and biceps brachii muscles suggested no evidence of systematic error. The trapezius MT and MQ significantly increased, and biceps brachii MT significantly in-creased after exercise (p<0.05). Notably, both A-mode and B-mode exhibited the same tendency in these post-exercise changes in muscle. This study suggests that low-cost and low-resolution A-mode US provides measurements of SFT, MT, and MQ similar to more expensive, high-resolution B-mode imaging. A-mode US can serve as an affordable and portable alternative for muscle assessment.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

The purpose of this finite element analysis (FEA) was to evaluate the stress experienced by both the prosthetic components and the bone in relation to varying cement thicknesses ranging from 20 to 60 μm, utilized in the attachment of a zirconia crown on a conometric cap. The study focused on two distinct types of implants (Cyroth and TAC, AoN Implants, Grisignano di Zocco, Italy) featuring a Morse cone connection. Detailed three-dimensional (3D) models were created to repre-sent the bone structure (cortical and trabecular) and the prosthetic components, encompassing the crown, cement, cap, abutment, and the implant. The two implants were placed in a 1.5 mm sub-crestal position and subjected to an inclined load of 200 N at 45° on the crown. The results re-vealed that an increase in cement thickness resulted in a reduction of von Mises stress on the cor-tical bone for both Cyroth and TAC implants, while the decrease in stress on the trabecular bone was relatively less pronounced. However, the TAC implant exhibited a higher stress field and de-formation in the apical area compared to the Cyroth implant. In summary, this study investigated the impact of cement thickness on stress transmission across prosthetic components and peri-implant tissues by means of FEA analysis, indicating that the 60 μm cement layer manifested higher stress values nearing the material strength limit.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

Epirubicin, olaparib and ribociclib are three anti-tumoral molecules currently used in cancer therapy. Since serum levels of these drugs reveal a large inter-individual variability, validation of a fast, simple and reliable analytical method for quantitative determination of these molecules in human serum, with Therapeutic Drug Monitoring (TDM) purposes would be necessary. Papers in literature describe separation, identification and quantitation of the drugs in pharmaceutical formulas and biological matrices. The large majority of these approaches use protein precipitation for sample pre-treatment, followed by LC separation and tandem-mass-spectrometry (MS/MS) detection. We propose an alternative method using Solid Phase Extraction (SPE) with Oasis PRiME HLB® cartridges followed by high-performance liquid chromatography (HPLC) using a C18 (4.6 × 50 mm) column. A gradient mobile phase with 0.1% formic acid/acetonitrile was utilized. MS detection in single ion recording (SIR) mode was employed. A 13-minutes run-time analysis, including column re-equilibration was assessed. Data for all molecules were validated according to ICH Guidelines. Calibration curves for all analytes were linear with correlation coefficient larger than 0.997. Values for precision were less than 6%. The method was applied on serum samples from patients up-taking the drugs, proving its suitability in TDM assisted adjustment of doses in therapy.

Atmospheric pollens were investigated using the Lanzoni VPSS 2000 device for 2 years between 2012 and 2013 in the Sarıkamış district of Kars province, one of the highest regions of Türkiye. A total of 37909 pollen grains were collected; 15,298 pollen grains in 2012 and 22611 pollen grains in 2013. Out of 43 identified taxa, 21 were arboreal and 22 were non arboreal. Pollen from arboreal plants accounted for 36.34% (13778 pollen) of the total, while pollen from non arboreal plants accounted for 63.56% (24095 pollen). The most frequent arboreal plants pollen in the Sarıkamış atmosphere were Pinaceae (29.79%), Cupressaceae/Taxaceae (2.54%), and Morus (1.30%). The main non arboreal plants pollen in the atmosphere of Sarıkamış were Poaceae (44.60%), Artemisia (2.98%), Amaranthaceae (2.79%), Rumex (2.41%), Urticaceae (2.33%), Plantago (2.19%), and Boraginaceae (1.40%). The maximum pollen concentration was observed in June.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

The European Union's recent decision to renew the authorization for the use of glyphosate until 15 December 2033 stimulates the scientific discussion all around the world regarding its toxicity or otherwise for humans. Glyphosate is a chemical used by millions of tons in the last 50 years worldwide to drying weeds in cultivated fields, greenhouses, roadsides. Concern has been raised in many quarters about the possible presence in the food chain and the consequent adverse effects on health: both aspects that argue in favor of toxicity and those that instead may indicate limited toxicity of glyphosate are here discussed. The great debate that has been generated requires further investigations and field measurements to understand its fate once dispersed in the environment and its concentration in the food chain. Hence the need for validated analytical methods that are available to analysts in the field. In the present review, methods for the analytical determination of glyphosate and its main metabolite, AMPA, are discussed, with a specific focus on chromatographic techniques applied to cereal products. The experimental procedures are explained in any detail, including cleanup, derivatization, and instrumental conditions to give the laboratories involved enough information to proceed with the implementation of this line of analysis. The prevalent chromatographic methods used are LC-MS/MS, GC-MS/SIM, and GC-MS/MS but sufficient indications are also given to those laboratories that wish to use the simpler HPLC-FLD, HPLC-UV, GC-NPD or GC-FPD techniques for screening purposes. Concentrations from literature measured in wheat, corn, barley, rye, oats, soybean, and cereal-based foods are reported together with the regulatory status in various parts of the world and the accumulation mechanism. As for the accumulation in cereals, available data show that glyphosate tends to accumulate more in wholemeal flours than in refined ones, that its concentration in the product strictly depends on the treatment period (the closer it is to the time of harvesting, the higher the concentration) and that in cold climates the herbicide tends to persist in the soil for a long time.

In pediatric burn care, achieving swift healing with minimal complications remains paramount. This investigation assesses polyhexamethylene biguanide (PHMB)'s role in managing superficial partial-thickness burns in children, focusing on the effects of various patient-specific factors on recovery. Through a retrospective analysis of 27 pediatric cases treated with PHMB, we explored the impact of age, burn size, dressing frequency, treatment delay, cold therapy application, and analgesic usage on the duration until reepithelialization. Notably, the majority of patients benefited from early cold therapy, yet only 1 in 3 patients received analgesics. The study reveals a mean healing time of 8.78 days, with the extent of the burn showing a strong correlation to recovery speed. Most treatments were managed outpatient, evidenced by a negligible average hospital stay. Impressively, the intervention recorded no complications. Our findings endorse PHMB as a promising treatment for second-degree burns in young patients, offering healing efficiency on par with or surpassing traditional methods, without increasing complication risks. This investigation underscores the necessity for continued exploration into the optimal application of prehospital interventions and the comprehensive benefits of PHMB in pediatric burn management, advocating for future research aimed at assessing long-term outcomes, including scar quality and patient satisfaction.

An effort was made to find a relationship between the ratio of average asperities height and lubricant thickness at the point of contact of rolling element ball bearings, and empirical equations to predict the life for bearings under constant motion. Two independent failure mechanisms were considered, fatigue failure and lubricant failure resulting in seizing of the roller bearing. A theoretical formula for both of these methods was established for the combined probability of failure using both of these failure mechanisms. Fatigue failure was modeled with the empirical equations of Lundberg and Palmgren and standardized in DIN/ISO281. The seizure failure, which this effort sought to investigate, was predicted using Greenwood and Williamson's theories on surface roughness and asperities during lubricated contact. These two mechanisms were combined, and compared to predicted cycle lives of commercial roller bearing, and a clear correlation was demonstrated. This effort demonstrated that the Greenwood-Williams theories on the relative height of asperities versus lubricant film thickness can be used to predict the probability of a lubricant failure resulting in a roller bearing seizing during use.

An effort was made to find a relationship between the predicted tribological conditions at the point of contact of ball bearings, and empirical equations to predict the life for bearings under constant motion. The model was modified to predict the temperature dependence, and compare rapid accelerations and decelerations with empirical extrapolations.

Background/Objectives: Patients with chronic kidney disease (CKD) have an increased risk of cardiovascular disease (CVD). Carotid intima-media thickness (C-IMT) is a non-invasive marker of atherosclerosis. Low omega-3 polyunsaturated fatty acids (PUFA) intake and vitamin D deficiency are potential cardiometabolic risk factors in patients with CKD. The aim of this study was to evaluate dietary intake and status of omega-3 PUFA and vitamin D in pre-dialysis and hemodialysis patients and to examine the link of dietary α-linolenic acid (ALA) and fish consumption with blood pressure and C-IMT in CKD patients. Methods: All 77 selected patients (36 pre-dialysis, 41 on hemodialysis) underwent standardized clinical, nutritional, and laboratory assessments. Repeated 24-hour recalls were performed to assess dietary intake. The fatty acid profile was determined by gas-liquid chromatography. Results: Inadequate vitamin D intake and vitamin D status were found in 95% of patients. PUFAs profiles did not differ between hemodialysis and pre-dialysis participants. Dietary intake of ALA was negatively correlated with systolic blood pressure (SBP) (p=0.007), C-IMT (p=0.002), serum CRP (p=0.044), iPTH (p=0.01) and 25(OH)D3 (p=0.006). ALA intake of more than 0.23 g/daily was associated with lower SBP (p=0.001), serum 25(OH)D3 (p=0.004), and C-IMT (p=0.002). Conclusions: This study contributes to a better understanding of the relationship between dietary ALA intake and C-IMT in CKD. The results of this study could emphasize the significant role of the high prevalence of vitamin D deficiency and inadequate omega-3 PUFA intake and status considering CVD health in CKD patients.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The aim of the study is to obtain a more complete picture of the blood plasma melatonin concentration in the donkey species. To this purpose sampling and statistical processing were carried out in such a way that allowed to establish the annual and daily rhythm. Based on human observations, according to the hypothesis of the authors, the blood plasma melatonin concentration of pregnant individuals rises during late gestational period, before parturition. To confirm this, the melatonin concentration of pregnant and non-pregnant mares was monitored and compared. In regard to the circannual rhythm, the significantly lowest midnight melatonin value (27.67 pg/ml) is typical for the summer solstice. Under consideration of circadian changes, a significantly strongest melatonin production (45.16 pg/ml) can be observed on the night of the winter solstice (p &lt; 0.001). Considering the gestational age, the blood plasma melatonin concentration (around 38 pg/ml) does not change as pregnancy progresses (p = 0.136). The results obtained in the study population of the domestic ass usefully expand the little knowledge previously gathered about the development of blood plasma melatonin concentration of this species.

A three-dimensional vector field model is proposed, whose dimensions are the Hansen Solubility Parameters: dispersion parameter (δD), polarity parameter (δP), and hydrogen bonding parameter (δH). The vector space that defines the field has the peculiarity of having the dispersion vector with a magnitude of 2, as its base vector, while polarity and hydrogen bonding vectors have a magnitude of 1. A substance is characterised as a position vector, and the interaction between two substances is determined by calculating the vector difference of both, known as the interaction vector. Interaction among substances may involve solubility, swelling, cracking, surface tension, interface tension, and any physical phenomena where intermolecular energies of dispersion, polarity or hydrogen bonding come into play. This paper studies free surface energy (surface and interfacial tension). It has been found that free surface energy is directly proportional to the square of the magnitude of the interaction vector. The proportionality constant, τ, is expressed in length units, has a value of 0.025 nm, and does not depend on the chemical nature of the substance or state of matter (solid, liquid or gas). Constant value τ appears universal and aligns with the thickness of interfaces, thereby supporting Guggenheim's hypothesis. This hypothesis asserts that interfaces possess actual thickness and are not merely mathematical surfaces, as originally postulated by Gibbs. Moreover, it also has been found that interface thickness, τ, is approximately equal to half of the Bohr radius, a0, which is defined by universal constants. Because the solubility parameters of thousands of substances are known and can be easily determined from molecular structure, a good approximation of the surface and interfacial tension of any given substance can now be calculated. It has also been found that contact angles of sessile droplets in three-phased systems can be calculated from the interaction vectors of the implicated substances.

Introduction: Migraine is one of the most prominent headache disorders with a global burden of over one billion patients and presented as a disabling and painful disorder. Pathophysiological mechanism of migraine is not fully understood, but the most accepted theory suggests that migraine is caused primarily by neural dysfunction leading to secondary changes in cerebral perfusion. Methods: Authors conducted a case-control study in 175 patients; 88 of them were migraineurs and 87 health controls. Optical coherence tomography (OCT) was performed in all patients using spectral-domain OCT device in the same environmental conditions. All participants met both inclusion and exclusion criteria in order to achieve more homogeneous groups. OCT was performed to scan all retinal layers with an emphasis on the inner plexiform layer (IPL). Results: Among 175 examined subjects, 84% of them were women and in the group of migraineurs we found 56% without aura and 44 % with aura. After collecting tomography data authors did not find subjects in which changes of IPL were found. Nevertheless, only moderate differences in the IPL thickness in all quadrants except the central area were found in the group of migraineurs with aura using Pearson’s test. Conclusion: According to presented results, no significant changes of the IPL thickness in migraine patients were found. Authors have to emphasize the need for further investigation of the relationship between average migraine headache days per month and the thickness of the IPL.

Background: We prepared reference materials of fentanyl and amphetamines in hair, and established methods for the certification of reference materials of fentanyl and amphetamines in hair samples. Methods: Hair samples containing 15 drugs were prepared by immersion method (water-dimethylsulfoxide). On the basis of single-factor experiment, Box-Behnken design-response surface was used to optimize the pre-treatment conditions of samples. In MRM/SIM mode, 15 drugs were quantitatively analyzed by LC-MS/MS and GC-MS/MS methods. Results: The contents of 15 drugs in the mixed hair samples were: 1.050 ng mg-1~7.771 ng mg-1, RSDs&lt;7%(n=11). The results showed that the two analytical methods developed were highly sensitive (LODs as low as 0.05 pg mg-1), reproducible (intra-day and inter-day precision RSDs were&lt;10%) and accurate. F-test was performed on the prepared hair samples and the results showed that the homogeneity of the prepared hair samples was good. Conclusions: The established methods were used for the detection of fentanyl and amphetamine drugs in human hair, with high sensitivity, accuracy and specificity. It can be used as a certified method for the development of fentanyl and amphetamine matrix certified reference materials. The developed hair reference materials are expected to be applied in forensic drug abuse detection and laboratory quality control.

Determining precise boundaries and protective zones for historical and cultural objects enables their effective preservation. This is particularly crucial in the face of increasing tourism, urbanization, and natural disasters. Accurately defining boundaries and protective zones can aid in the planning of scientific research, archaeological excavations, and other studies aimed at exploring the history and cultural significance of these objects. The article presents the framework for establishing protective zones around historical and cultural heritage sites existing in Ukraine, using the example of the Citadel defensive complex located in Lviv (Ukraine). It proposes general and detailed conceptual models for the combined application of remote and non-invasive methods for investigating historical and cultural heritage sites. This conceptual article introduces the theory of integrating radar satellite imaging with ground-based georadar imaging. Additionally, it presents a software module that has been developed to analyze collected data on two-dimensional historical and cultural heritage objects, refine their boundaries, and establish protective zones around them.

The organic solar cells (OSCs) have drawn attention in the past decade due to its cynosure in industrial manufacturing because of its promising properties such as low weight, highly flexible and low cost production. However, low η restricts the utilization of OSCs for potential application such as low cost energy harvesting devices. In this paper, OSCs structure based on triple junction tandem scheme is reported with three different absorber materials with the objective to enhance the absorption of photons which in turn improves the η, as well as its correlating performance parameters. The investigated structure gives the higher value of η = 14.33% with Jsc=16.87 (mA/m2), Voc=1.0 (V), and FF=84.97% by utilizing a stack of three different absorber layers with different band energies. The proposed structure is tested under 1.5 (AM) with 1 sun (W/m2). The impact of top, middle and bottom sub cells thickness on η is analyzed with a terse to find the optimum thickness for three sub cells to extract high η. The optimized structure is then tested with different electrode combination and the highest η is recorded with FTO/Ag. Moreover, the influence of upsurge temperature is also demonstrated on the proposed structure and observed that the upsurge temperature has greatly affected the electrical parameters of the device and η decreases from 14.33% to 11.40% when the temperature of the device rises from 300-400 K.

Background: Vestibular Neuritis (VN) induces Acute Vestibular Syndrome (AVS). This study aimed to identify predictive factors of VN recovery by healing and/or compensation. Methods: In this longitudinal and prospective study, 40 patients were included. The first assessment (T0) included medical history taking (general and specific), for cardiovascular risk factors (CVRFs), a battery of diagnostic tests, bithermal caloric test (BCT), video Head Impulse Test (VHIT) and skull vibration induced nystagmus (SVIN). All patients also completed a Dizziness Handicap Inventory (DHI). All assessments were repeated 90±15 days (T3) later. Subjective criteria compensation were based on DHI total score and objective criteria compensation on the instrumental test results. Four groups of patients (A, B, C, D) were delineated by combining patients with normal vs abnormal vestibular tests and patients with normal vs abnormal DH. Results: CVRFs were associated with a poorer recovery of symptoms but not the age or BMI. Vestibular tests mainly BCT (canal paresis %), VHIT (lateral semicircular canal gain) and SVINT (nystagmus slow phase velocity) recovered within normal values in 20%, 20%, 26% of cases respectively at T3 for the 40-patient group. Conclusions: Vascular risk factors (hypercholesterolemia) are correlated with patients who do not recover their symptoms either by healing or compensation. The evolution did not show any significant difference between high or low frequency vestibular tests in patients recovering from their symptoms. However, some patients with objective recovery may continue to show persisting subjective symptoms.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil &amp; gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

Determining the estrous cycle stages in mice is essential for optimizing breeding strategies, synchronizing experimental time lines, and facilitating studies in behavior, drug testing, and genetics. It is critical for reducing the production of genetically unmodified offspring in the generation and investigation of genetically modified animal models. An accurate detection of the estrus cycle is particularly relevant in the context of the 3Rs—Replacement, Reduction and Refinement. The estrous cycle, encompassing the reproductive phases of mice, is key to refining experimental designs and addressing ethical issues related to the use of animals in research. This study presents results from two independent laboratories on the efficacy of the Mouse Estrus Detector (MED) from Elmi Ltd. (Latvia) for the accurate determination of the estrus phase. The female mice of five strains/stocks (CD1, FVB/N, C57Bl6/J, B6D2F1, and Swiss) were used. The results showed that the MEDProTM is a low -traumatic, simple, rapid and painless method of estrus detection that supports the principles of the 3Rs. The use of the MEDProTM for estrus detection in mice caused minimal stress, enhanced mating efficiency, facilitated an increase in the number of embryos for the in vitro fertilization and allowed the production of the desired number of foster animals.

Emergency Health Services refers to the urgent care. Ambulance abuse threaten the provision of proper health services and at the same time it affects the country's economy negatively. It was aimed to determine ambulance abuse level. This was a retrospective cohort research. In order to carry out our study, we analyzed 12,207 cases who called to the 112 Emergency Ambulance Services between 01.01.2016 and 31.12.2016. The data of the study has been obtained from the Emergency Health Automation System of the Provincial Health Directorate. According to preliminary diagnoses, traumatic cases were found to be 19.4% and cardiovascular cases were 12%. According to the World Health Organization 32 Critical Code List 59.6% of the cases who called to the 112 Emergency Ambulance Services in 2016 were inappropriate. Ambulance abuse rate was 59.6%. The high rate of misuse of 112 emergency ambulances affects the service flow and motivation of the staff negatively and causes extra financial burden. Thereof, awareness trainings should be given to the public and task and duties of the paramedics and emergency medical technicians who work at emergency ambulances should be expanded so that the transfer of unnecessary cases should be prevented.

This study was to explore the effects of glabridin and gymnemic acid on the structural changes of the choroidal layer as well as the expression of VEGF and CD31 in diabetic rats. The animals were separated into five groups: the control group (C), the diabetic group (DM), the diabetic rats treated with glabridin 40 mg/kg body weight (DM+GB), the diabetic rats treated with gymnemic acid 400 mg/kg body weight (DM+GM), and the diabetic rats treated with glyburide 4 mg/kg body weight (DM+GR). There has been an increase in the thickness of both the choroid layer and the wall of the arteries in the diabetic group. A decrease in vascularity and choroidal neovascularization can be found in DM rats. After eight weeks of experimentation, the choroidal thickness and wall of choroid arteries, as well as the diameter of the lumen of choroid arteries in the DM+GB, DM+GM, and DM+GR groups, had improved. The expression of VEGF and CD31 was lower compared to the DM group. According to the findings of the current research, glabridin and gymnemic acid can improve and reduce the damage to the choroid, which is a factor that can sometimes result in vision loss.

The research field of two dimensional (2D) materials strongly relies on optical microscopy characterization tools to identify atomically thin materials and to determine their number of layers. Moreover, optical microscopy-based techniques also opened the door to study the optical properties of these nanomaterials. We present a comprehensive study of the differential reflectance spectra of 2D semiconducting transition metal dichalcogenides (TMDCs), MoS₂, MoSe₂, WS₂ and WSe₂, with thickness ranging from one layer up to six layers. We analyze the thickness-dependent energy of the different excitonic features, indicating the change in the band structure of the different TMDC materials with the number of layers. Our work provides a route to employ differential reflectance spectroscopy for determining the number of layers of MoS₂, MoSe₂, WS₂ and WSe₂.

Current antibiograms cannot discern the particular effect of a specific antibiotic when the bacteria are incubated with a mixture of antibiotics. To prove that this task is achievable, Escherichia coli strains were treated with ciprofloxacin for 45 min, immobilized on a slide and stained with SYBR Gold. In susceptible strains, the nucleoid relative surface started to decrease near the MIC, being progressively condensed as dose increased. The shrinkage level correlated with the DNA fragmentation degree. Ciprofloxacin-resistant bacilli showed no change. Additionally, E. coli strains were incubated with ampicillin for 45 min and processed similarly. The ampicillin-susceptible strain revealed intercellular DNA fragments that increased with dose, unlike the resistant strain. Co-incubation with both antibiotics revealed that ampicillin did not modify the nucleoid condensation effect of ciprofloxacin, whereas the quinolone partially decreased the background of DNA fragments induced by ampicillin. Sixty clinical isolates, with different combinations of susceptibility-resistance to each antibiotic, were co-incubated with the EUCAST breakpoints of susceptibility of ciprofloxacin and ampicillin. The morphological assay correctly categorized all the strains for each antibiotic in 60 min, demonstrating the feasible independent evaluation of a mixture of quinolone and beta-lactam. The rapid phenotypic assay may shorten the incubation times and necessary microbial mass currently required for evaluation.

We have performed first-principles calculations to study the interfacial exchange coupling and magnetocrystalline anisotropy (MCA) energy in a SmCo₅/Sm₂Co₁₇ multilayer model systems. The phase of SmCo₅ and Sm₂Co₁₇ stacking along (0001) direction are structurally well matched. The atomic structure, including the alignment and the separation between layers, were firstly optimized. Then the non-collinear magnetic structures were calculated to explore the exchange coupling across the interface and the variation of MCA energy. We found that the inter-phase exchange coupling strength, rotating behavior and MCA energy are strongly dependent on the atomic thickness of the SmCo₅ and Sm₂Co₁₇ phase.

An adequate representation of the water infiltration process in the soil allows improving the efficiency in application and the uniformity in surface irrigation. The Green and Ampt model has shown a good representation of the process, and researchers from the United States Department of Agriculture (USDA) determined the values of their parameters for soils of that country, which are shown in tables or through functional relationships and this information is used as reference in several parts of the world, although there is no certainty that they are representative of the soils in Mexico. In this study, the parameters of the Green & Ampt equation were determined and evaluated in some soils of agricultural importance in Mexico. The parameters were obtained in four ways: one of them applied a methodology adapted from Brooks and Corey to quantify the wetting front capillary pressure head and used an permeameter under constant hydraulic head to determine the saturated hydraulic conductivity, and the other three consisted in taking them from three studies reported by the USDA. The values of the parameters suggested in Mexico drastically underestimated the results with relative errors (RE) in a range of -49.0 to -94.0% and the most representative were those obtained with the methodology proposed in this research with RE of -15.0 to 6.0%.

The technology for determining the point’s coordinates on the earth’s surface using the global navigation satellite system (GNSS) is becoming the norm along with ground-based methods. In this case, determining coordinates does not cause any particular difficulties. However, to identify normal heights using this technology with a given accuracy, special research is required. The fact is that satellite determinations of geodetic heights (h) over an ellipsoid surface differ from ground-based measurements of normal height (HN) over a quasi-geoid surface by a certain value called quasi-geoid height or height anomaly (ζ). In relation to determining heights of a certain territory, the concept of geoid height (N) is usually operated when dealing with a geoid model. In this work, geodetic and normal heights are determined for 5 control points in three different regions in Lebanon, where measurements are carried out using GNSS technology and geometric levelling. The obtained quasi-geoid heights are compared with geoid heights derived from the global Earth model EGM2008. The results obtained showed that, in the absence of gravimetric data, the combination of global Earth model data, geometric levelling for selected areas and satellite determinations allows the creation of a high accurate altitude network for mountainous areas.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

Introduction: intraocular pressure (IOP) measurement is an essential part glaucoma’s diagnosis and follow-up. Goldmann applanation tonometry (GAT) is the gold standard for IOP measurement but it’s affected by many factors like central corneal thickness (CCT). Racial differences in CCT are reported but the Syrian population was never studied. Research design and methods: 57 subjects with 114 eyes visiting Damascus hospital were examined and 100 eyes were included. IOP was measured using GAT and CCT was measured using OCULUS Pentacam AXL Corneal Topography, demographic data and history of ocular surgery, systemic co-morbidities and history of medications were collected. IOP values were corrected for CCT. Results: 56% were males, the mean age was 48.1. 24% of subjects had hypertension. Males had higher CCT with 557.23± 25.33 compared with 531.34 ± 41.88 for females. There was a moderately positive correlation between CCT and IOP (r=0.232, p-0.02), CCT and IOP values were linearly correlated (ANOVA, p=0.02). Conclusions: This study showed that the correlation between CCT and IOP is present in the Syrian population. Males had a slightly thicker corneas than females and CCT didn’t significantly change with age.

Age-related macular degeneration (AMD) causes visual impairment in individuals >50 years of age. However, no study has investigated AMD using ultra-wide-field swept-source optical co-herence tomography (UWF SS-OCT). We aimed to evaluate central and peripheral choroidal thickness using UWF SS-OCT and compare AMD subtypes. We included 75 eyes of patients with typical AMD (tAMD), 56 with polypoidal choroidal vasculopathy (PCV), 29 with pachychoroid neovasculopathy (PNV), and 12 with retinal angiomatous proliferation (RAP). To compare cho-roidal thicknesses in the central and peripheral choroids, we established subfields of <3 mm, <9 mm, and 9–18 mm from the fovea. PNV patients were significantly younger than those with tAMD (P=0.01). The choroidal thicknesses of PNV were significantly greater than that of tAMD in all subfields (P<0.01) and choroidal thickness significantly correlated with age and axial length in all subfields (P<0.05). Even after adjusting for age and axial length, the choroidal thickness in PNV was significantly greater than that in tAMD (P<0.05). In addition, the ratio of the posterior < 9 mm to peripheral 9–18 mm choroidal thickness in PNV was significantly greater than that in tAMD (P<0.01). A thickened choroid in PNV was more pronounced in the posterior choroid than in the periphery.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

This algorithm is designed to perform Discrete Fourier Transforms (DFT) to convert temporal data into spectral data. This algorithm obtains the Fourier Transforms by studying the Coefficient of Determination of a series of artificial sinusoidal functions with the temporal data, and normalizing the variance data into a high-resolution spectral representation of the time-domain data with a finite sampling rate. What is especially beneficial about this DFT algorithm is that it can produce spectral data at any user-defined resolution.

Overhead power transmission line icing (PTLI) disasters are one of the most severe dangers to power grid safety. Automatic iced transmission line identification is critical in various fields. However, existing methods primarily focus on the linear characteristics of transmission lines, employing a two-step process involving edge and line detection for PTLI identification. Nonetheless, these traditional methods are often difficult when confronted with challenges such as background noise or variations in illumination, leading to incomplete identification of the target area, missed target regions, or misclassification of background pixels as foreground. We propose a new iced transmission line identification scheme to overcome this limitation. In the initial stage, we integrate the image restoration method with image filter enhancement to restore the image's color information. This combined approach effectively retains valuable information and preserves the original image quality, thereby mitigating noise presented during the image acquisition. Subsequently, in the second stage, we introduce an enhanced multi-threshold algorithm to separate background and target pixels. After image segmentation, we enhance the image and obtain the region of interest (ROI) through connected component labeling modification and mathematical morphology operations, eliminating background regions. Our proposed scheme achieves an accuracy value of 97.72%, a precision value of 96.24%, a recall value of 86.22%, and the specificity value of 99.48% based on the average value of test images. Through object segmentation and location, the proposed method can avoid background interference, effectively solve the problem of transmission line icing identification, and achieve 90% measurement accuracy compared to manual measurement on the collected PTLI dataset.

The purpose of the study was to determine the “retinal thickness deviation” (RTD) in diabetic macular edema (DME) eyes treated with intravitreal therapy and to establish associations be-tween RTD and best-corrected visual acuity (BCVA). We conducted a retrospective study, in-cluding consecutive DME eyes undergoing intravitreal therapy with two years of follow-up. BCVA and central subfield thickness (CST) were collected at baseline, 12 months and 24 months of follow-up. RTD was calculated as the absolute difference between measured and normative CST values at each time point. Linear regression analyses were performed between RTD and BCVA and between CST and BCVA. One hundred and four eyes were included in the analysis. The RTD was 177.0 (117.2) μm at baseline, 97.0 (99.7) μm at 12 months and 89.9 (75.3) μm at 24 months of follow-up (P < .001). RTD showed a moderate association with BCVA at baseline (R2=0.134, p<0.001) and 12 months (R2=0.197, p<0.001), and a substantial association at 24 months (R2=0.272, p<0.001). The CST showed a moderate association with BCVA at baseline (R2=0.132, p<0.001) and 12 months (R2=0.136, p<0.001), while the association was weak at 24 months (R2=0.065, p=0.009). In conclusion, RTD showed a good association with visual outcome in DME eyes undergoing intravitreal treatment.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

In this study on volume determination in waste sorting facilities, we evaluate the effectiveness of ultrasonic sensors and address waste-material-specific challenges. Although ultrasonic sensors offer a cost-effective automation solution, their accuracy is affected by irregular waste shapes, varied compositions, and environmental factors. Notable inconsistencies in volume measurements between storage bunkers and conveyor belts underscore the need for a comprehensive approach to standardize bale production. With prediction reliability being constrained by limited data sets, undocumented modifications to machine-settings and sensor failures, this task renders a challenging application area for Machine Learning. We explore related research and present dataset analyses from three distinct waste sorting facilities in Europe, addressing issues as sensor usability, data quality and material specifics. Our analysis suggests promising strategies and future directions for enhancing waste volume measurement accuracy, ultimately aiming to advance sustainable waste management.

Brazil chicken production is around 13 million tons and about a third is exported to over 150 countries, placing Brazil as the world largest chicken meat producer, and therefore it is crucial to follow the legislation of all importer markets. This study conducted a survey by chance in 45 meat industries able to export. Therefore, 2580 chicken meat samples were collected and submitted to 11 analyte extraction and chromatographic verification of compliance in an accredited laboratory. Ten chemical residues (amoxicillin, bacitracin, colistin, dinitolmide + zoalene, spectinomycin, roxarsone, tiamulin, tylosin, trenbolone acetate and virginiamycin) were investigated in chicken meat and one (halofuginone hydrobromide) in chicken liver. The results showed that no compound exceeded the maximum residue limits established by seven legislations. All residue concentrations found were below the method quantification limit, thereby confirming the capability of Brazilian chicken meat industries in complying to foreign markets.

Recent works in mechanical fatigue consider that a threshold of entropy exists, the fracture fatigue entropy. The determination of this quantity is usually done considering empirical models for the mechanical power estimation. In this paper, we experimentally observe the existence of a threshold of entropy and exergy in low cycle fatigue for a flat Al-2024 specimen avoiding the use of a model, solely measuring the heat generated during a fatigue test. Results are then compared considering various hypotheses (1D heat dissipation with convection and radiation considered as heat sources, and, heat transfer from a fin with convection and radiation as boundary conditions) to an empirical mechanical model known in the literature and deviations between them are discussed.

Debris flows have generated major disasters worldwide due to their great destructive capacity, which is associated with their high energy levels and short response times. To achieve an adequate risk management of these events, it is necessary to define as accurately as possible the different hazard levels to which the territory is exposed. This article develops a new methodology to estimate this hazard based on the hydrodynamic characteristics of the flow and the granulometry of the sediments that can be mobilized by the flow. The hydrodynamic characteristics of the flow are determined through a mathematical modeling that considers the rheology of non-Newtonian flows and the different volumes of sediments that could be transported during events corresponding to different return periods. The proposed methodology was implemented in the Jamundí River basin (Colombia). The results obtained indicate that in the upper part of this basin there is a low hazard level, while in the lower part of the basin approximately 15% of the affected territory has a medium hazard level and the remaining 85% has a low hazard level. The methodology developed is simple to implement but technically rigorous since it considers all relevant aspects in the generation of debris flows.

Throughout the ages and times, the need to use everything that reflects women's beauty and helps them maintain their vision and health, and if the need to use the precious materials has been put in place, it is important that they produce the desired results without attention to the harmful chemicals and heavy metals that they contain. Over time, the toxicity of these heavy metals increases in our environment because of their long-term exposure to these pollutants, whether low or high-level in toxicity, animal-prednmost, environment, including air we breathe, water, food, etc. Cosmetics are one of these sources through which humans are exposed to heavy toxic metals. Heavy metals have been estimated in a number of previous studies, and in our study here, we aim to estimate the amount of cadmium metal and study it in various cosmetics such as Lipstick, Eye shadow, Face whitening cream. Two samples were taken from each of the locomoys and cadmium was estimated using the photometer of atomic absorption, one of the samples being expensive and the other low-cost, and purchased from the wholesale markets of Taiz City. Cadmium has been found prominently in these products and the highest rate found in the lowest cost-effective, Eye shadow, that the use of these cosmetic products exposes users to low- conc. heavy metals, which may pose a danger to their health. They are known to be clustered in their biological systems over time, resulting in an imbalance of body and environment. The results found that the low-priced color samples contained a higher concentration of cadmium than the high-price samples in low-priced samples, cadmium concentration was in order of eye shadow > lipstick = face whitening cream. The similar pattern are shown also for higher price product, which are lipstick > face whitening cream > eye shadow.

Dampers provide safety by control of unwanted motion, due to conversion of mechanical work into another form of energy (e.g., heat). State of the art materials are elastomers including thermoplastic-elastomers. For polymer-appropriate replacement of multi-component shock absorbers comprising mounts, rods, hydraulic fluids, pneumatic devices, or electro-magnetic devices, among others, deep insights of the dynamic thermo-mechanical characteristics of damper materials have to be gained. The ultimate objective is to reduce complexity by utilizing inherent material damping rather than structural (multi-component) damping properties. The objective of this work was to compare the damping behavior of different elastomeric materials including thermoplastic poly(urethane) (TPU), and silicone rubber blends (mixtures of different poly(dimethylsiloxane) (PDMS)). Therefore, the materials were hyper- and viscoelastic characterized, a finite element calculation of a ball-drop test was performed, and for validation the rebound resilience was measured experimentally. In an attempt, the coil-over shock absorber of a model car was replaced by a damper made of the examined and modeled materials. The results revealed that the material parameter determination methodology is reliable, and the data applied for simulation lead to realistic predictions. Interestingly, the rebound resilience of the mixture of soft and hard PDMS (50:50)w% is the highest and the lowest values were measured for TPU.

Lake ice thickness (LIT) is a sensitive indicator of climate change identified as a thematic variable of Lakes as an Essential Climate Variable (ECV) by the Global Climate Observing System (GCOS). Here, we present a novel and efficient analytically based retracking approach for estimating LIT from high-resolution Ku-band (13.6 GHz) synthetic aperture radar (SAR) altimetry data. The retracker method is based on the analytical modeling of the SAR radar echoes over ice-covered lakes that show a characteristic double-peak feature attributed to the reflection of the Ku-band radar waves at the snow-ice and ice-water interfaces. The method is applied to Sentinel-6 Unfocused SAR (UFSAR) and Fully Focused SAR (FFSAR) data, with their corresponding tailored waveform model, referred to as the SAR_LITand FFSAR_LITretracker, respectively. LIT retrievals from Sentinel-6 SAR data at different posting rates are evaluated against those obtained from thermodynamic lake ice model simulations and Low Resolution Mode (LRM) Sentinel-6 and Jason-3 data over two ice seasons during the tandem phase of the two satellites, allowing precise assessment of the continuity between LRM and SAR LIT retrievals. Consistency checks of the Sentinel-6 SAR LIT estimates are also performed using optical/radar images that provide information on the snow/ice conditions on the same dates. The analysis is performed on Great Slave Lake and Baker Lake (Canada) that differ in terms of lake size, bathymetry, snow/ice properties, and seasonal evolution of LIT. The accuracy of the LIT estimates with the SAR LIT retrackers is on the order of 5 cm once the ice is well established on the lakes, meeting the GCOS requirements of LIT measurement uncertainty, which is a factor of 2 to 3 times better than that of LIT obtained with LRM data, bringing a further improvement compared to previous analyses and methods. The SAR LIT retrackers presented are promising tools for monitoring the inter-annual variability and trends in LIT from current and future SAR altimetry missions.

Pachychoroid neovasculopathy (PNV) is a pachychoroid-spectrum disease. As blood circulation throughout the choroid may be involved in PNV pathogenesis, analysis using ultra-wide-field (UWF) fundus imaging is crucial. We evaluated choroidal thickness after half-fluence photodynamic therapy (PDT) combined with intravitreal aflibercept injection for PNV using UWF swept-source optical coherence tomography. Seventeen eyes with PNV that underwent half-fluence PDT with adjuvant single intravitreal aflibercept injection were analyzed. To compare choroidal thicknesses in the central and peripheral choroids, we set subfields <3, <9, and 9–18 mm from the fovea. The <9- and 9–18-mm subfields were divided into four quadrants. Choroidal thickness in each subfield decreased significantly after half-fluence PDT (P<0.001); this reduction was more pronounced in the central area. We also investigated the relationship between the dominant side of the deep choroidal veins that harbor choroidal vein efflux from the macula. When choroidal thickness in the supratemporal and infratemporal 9x9-mm subfields were evaluated, the ratio of choroidal thickness reduction was not significantly different between the dominant and non-dominant sides. The dominant side was not associated with the extent of choroidal thickness reduction in PNV. In conclusion, half-fluence PDT caused thinning of the entire choroid, especially in the central area, in PNV.

Systematic results of lattice dynamical calculation are reported for the novel (SiC)m/(GeC)n superlattices (SLs) by exploiting a modified-linear chain model (M-LCM) and a realistic rigid-ion- model (RIM). By employing the bond polarizability method in the framework of M-LCM, we have simulated Raman intensities for the graded (SiC)10-D/(Si0.5Ge0.5C)D/(GeC)10-D/(Si0.5Ge0.5C)D SLs by carefully integrating interfacial layer thickness D (≡ 0, 1, 2, 3 monolayers (MLs)). The variation of D has initiated considerable up (down) shifts of GeC-, (SiC)-like Raman peaks in the middle of the optical phonon frequency region. With D = 3 MLs, the maximum energy shift (by ~ 47 cm-1) of SiC-like modes has caused substantial changes in the Raman intensity profiles linked to the localization of atomic displacements at the interfacial transition regions. This effect can be considered as a vital tool for authenticating the interfacial structures in technologically important SLs. By using a RIM, we have reported SL phonon dispersions along the growth [001] as well as in the plane [100], [110] perpendicular to the growth. Our simulations of phonons in the acoustic mode region have not only confirmed the formation of minigaps at the zone center and zone edges but also provided evidence of anti-crossing and phonon confinement. Besides examining angular dependence of zone-center optical modes, we have also discussed phonon folding, confinement and anisotropic behavior in (SiC)m/(GeC)n SLs.

The Combined Inversion of Surface and AeRosols (CISAR) algorithm for the joint retrieval of surface and aerosol single scattering properties has been further developed in order to extend the retrieval to clouds and overcome the need for an external cloud mask. Pixels located in the transition zone between pure cloud and pure aerosol are often discarded by both aerosol and cloud algorithms, despite being essential for studying aerosol-cloud interactions, which still represent the largest source of uncertainty in climate predictions. The proposed approach aims at filling this gap and deepening the understanding of aerosol properties in cloudy environments. The new CISAR version is applied to Sentinel-3A/SLSTR observations and evaluated against different satellite products and ground measurements. The spatial coverage is greatly improved with respect to algorithms processing only pixels flagged as clear sky by the SLSTR cloud mask. The continuous retrieval of aerosol properties without any safety zone around clouds opens new possibilities for studying aerosol properties in cloudy environments.

Plants characterized by a soft or weak steam, such as climbing plants, need to find a potential support (e.g., wooden trunk) to reach greater light exposure. Since Darwin’s research on climbing plants, several studies on their searching and attachment behaviors have demonstrated their unique ability to process different support features to modulate their movements accordingly. Nevertheless, the strategies underlying this ability are yet to be uncovered. The present research tries to fill this gap by investigating how the interaction between above- (i.e., stem, tendril, …) and belowground (i.e., the root system) plant organs influence the kinematics of the approach-to-grasp movement. With three-dimensional (3D) kinematical analysis, we characterized the movement of pea plants (Pisum sativum L.) towards a support with different thicknesses above and belowground (i.e., thin below, thick aboveground, or the opposite). As a control condition, the plants were presented to supports with the same thickness below- and aboveground (i.e., either entirely thin or thick). The results suggest an integration between the information from below- and aboveground for driving the reach-to-grasp behavior of the aerial plant organs. Information about the support conveyed by the root system seems particularly important to fulfil the end-goal of the movement.

Seafood products are the main dietary source of n-3 polyunsaturated fatty acids (n-3 PUFA), which are essential for human health. However, due to the widespread use of processed fish products, the presence of these n-3 PUFAs may be subject to changes related to different processing methods. The aim of this study was to determine the fatty acid composition, with a focus on n-3 polyunsaturated fatty acids (n-3 PUFAs), in different processed fish and shellfish food of EU and non-EU origin purchased in supermarkets and ethnic food shops in Messina (Italy), using gas chromatography with flame-ionization detector (GC-FID). From the fatty acid profile, the atherogenic index (AI), thrombogenicity index (TI) and flesh-lipid quality index (FLQ) were determined: 0.13-1.04 (AI), 0.31-9.84 (TI) and 0.41-29.90 (FLQ). The percentages of saturated (SFA), monounsaturated (MUFA) and polyunsaturated (PUFA) fatty acids had the following ranges: 13.55-50.48%, 18.91-65.58%, 13.84-52.73%, respectively. All samples showed a good presence of PUFAs and, in particular, eicosapentaenoic (EPA, 20:5n-3) and docosahexaenoic acid (DHA, 22:6n-3) were the main n-3 polyunsaturated fatty acids (n-3 PUFA).

Yam (Dioscorea spp.) is a monocotyledonous herbaceous vine plant grown in the tropics and subtropics. It is a multi-species plant with varied intra- and interspecific ploidy levels. Of the 600 species, 11 are cultivated staple supporting the livelihood of over 300 million people. The paucity of information on ploidy and the genomic constitution is a significant challenge to the crop’s genetic improvement through crossbreeding. The objective of this study was to investigate the ploidy levels of 236 accessions across six cultivated and two wild species using chromosome counting, flow cytometry and genotyping-based ploidy determination methods. Results obtained from chromosome counting and genotyping-based ploidy determination were in agreement. In majority of the accessions, chromosome counting and flow cytometry were congruent, allowing future rapid screening of ploidy levels using flow cytometry. Among cultivated accessions, 168 (71%) were diploid, 50 (21%) were triploid, and 12 (5%) were tetraploid. Two wild species included in the study were diploids. Resolution of ploidy level in yams offers opportunities for implementing successful breeding programmes through intra- and inter-specific hybridization.

The hot rolling in the process chain of the aluminium rolled products present the critical element of material quality and influence on productivity. The desire to increase the letter demand modifications of hot rolling, consequential changes of microstructure, crystallographic texture, mechanical and formability properties must be knowledge and consistently considered in planning the rolling process and rolled product. Achieving lower thicknesses of the hot-rolled band would enable fewer passes with cold rolling; consequently, hot rolling with the same number of passes will complete with lower temperatures. Microstructural and texture characterization with the optical microscope and scanning electron microscope for the hot-rolled band 3.25 mm the smaller grains appeared in the center of the cross-section, unlike for the hot-rolled band 6 mm, the smaller grains were detected on the upper and bottom position of the cross-section. Furthermore, the comparison shows also that the hot-rolled band 6 mm has 64 % of random texture components and 83 % of recrystallized grains, and the proportional adjustment for the hot-rolled band 3.25 mm has the 42 % of random texture components and 55 % of recrystallized grains. For the mechanical testing results, the elongation values in rolling and transverse directions significantly differ just in the case of a hot rolled band of 3.25 mm. Consequently, the earing results are more than 1.5 % higher for the hot-rolled band, 3.25 mm, than the hot-rolled band, 6 mm.

Background: Evaluating muscle mass and function among stroke patients is important. However, evaluating muscle volume and function is not easy due to the disturbance of consciousness and paresis. Temporal muscle thickness (TMT) has been introduced as a novel surrogate marker for muscle mass, function, and nutritional status. We herein performed a narrative literature review on temporal muscle and stroke to understand the current meaning of the TMT in the clinical stroke practice. Methods: The search was performed in PubMed, last updated in October 2021. Report on temporal muscle morphomics and stroke-related diseases or clinical entities were collected. Results: Four studies reported on TMT and subarachnoid hemorrhage, 2 intracerebral hemorrhage, 2 ischemic stroke, 2 standard TMT values, and 2 nutritional status. TMT was reported as a prognostic factor for several diseases, surrogate markers for skeletal muscle mass, and an indicator of nutritional status. Computed tomography, magnetic resonance imaging, and ultrasonography were used to measure TMT. Conclusions: TMT is gradually used as a prognostic factor of stroke or surrogate marker for skeletal muscle mass and nutritional status. Establishing standard methods to measure TMT and large prospective studies to investigate the further relationship between TMT and diseases are needed.

Alkali-Silica Reaction (ASR), which develops over time into a harmful internal reaction in concrete, produces a harmful gel due to the reaction between the reactive silica in the aggregate and the alkalis of the pore solution. Due to the multi-scale nature of this long-term phenomenon, understanding its mechanism in concrete structures remains difficult to assess. Accelerated Mortar Bar Testing (AMBT) ASTM C1260 is among the commonly used methods to understand ASR formation in a short time. In this study, the chemical characterisation of concretes produced from volcanic rock type basalt aggregate was compared with the chemical characterisation of ASR concretes after AMBT was applied. In addition, 20% FA was substituted into the concrete to investigate the effect of fly ash (FA) on ASR. Specimens with limestone aggregate (PL), basalt aggregate (BBC) and 20% basalt aggregate with fly ash substitution instead of cement (BBC20FA) were prepared for the investigation. Scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA) and differential thermal analysis (DTA) techniques were used to characterise the morphology and analytical composition of the concretes. It was determined that basalt aggregate does not cause ASR and its use with fly ash increases the strength and durability of concrete.

In the context of Kalman filters, the predicted error covariance matrix $\mathbf{P}_{k+1}$ and measurement noise covariance matrix $\mathbf{R}$ are used to represent the uncertainty of state variables and measurement noise, respectively. However, in real-world situations, these matrices may vary with time due to measurement faults. To address this issue in CubeSat attitude estimation, an adaptive extended Kalman filter has been proposed that can dynamically estimate the predicted error covariance matrix and measurement noise covariance matrix using an expectation-maximization approach. Simulation experiments have shown that this algorithm outperforms existing methods in terms of attitude estimation accuracy, particularly in sunlit and shadowed phases of the orbit, with the same filtering parameters and initial conditions.

Exact sequential state estimation of orbiting objects in space can be found by predicting the state using Fokker Planck Kolmogorov Equation (FPKE) and measurement correction using Bayes’ conditional/posterior Probability Density Function (PDF). Posterior PDF can be expressed as Gaussian density expanded in terms of Hermite polynomials named as Gram Charlier Series (GCS). This research is an extension of an earlier work on second order linearized solution to nonlinear Bayesian filtering using Taylor series and third order GCS expansion of posterior PDF. In this new extension, Bayes’ posterior PDF is approximated by a mixture of GCS functions for which the parameters are propagated using linear propagation theory. The update of weights of different components of GCS mixture model uses the FPKE error as feedback to adapt for the amplitude of different GCS components while solving a quadratic programming problem earlier used for Gaussian Mixture Model (GMM) PDF. Proposed filtering method is applied on tracking of space debris. The simulation results for the filter shows performance is moderately better than single GCS filter, Extended Kalman Filter (EKF) and Gaussian Sum Filter (GSF) under space debris’ highly uncertain initial conditions and sparse measurement availability.

Image processing is a field of which its popularity increases and continues and, that grows dynamically with new technologies. Nowadays, image processing finds itself in use in almost every field. One of these uses is undoubtedly in the field of medicine, where diagnosis and treatment planning are made from images and, which is constantly changing with newly developed techniques. Of course, the most important factor in using this so widely in the medical field is the acquisition of images on every medical field. With the help of these images, the complaints can be seen more easily and the doctor can follow a path in the treatment of the disease. In our study, we used the Region Growing segmentation method to detect the intestinal mass. This study compares the area determined by the specialist with the area obtained with the segmentation process and, it is seen that the created software system can be used as an auxiliary system to specialist doctors.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

The brown pelican (Pelecanus occidentalis) is a species often affected by natural and man-made disasters such as hurricanes and oil spills as well as general human activities; that subsequently receives medical care and rehabilitation. During rehabilitation, blood may be collected for various testing to help with diagnosis, treatment, and monitoring. Reference intervals for this species are limited, dated, and typically from small sample sizes. Seventy one presumed healthy brown pelicans were sampled as a part of their pre-release examination from rehabilitation at the Wildlife Center of Texas after a large volume stranding in December 2014 to January 2015, and various venous analytes were measured to establish updated reference intervals for Brown Pelicans. Fibrinogen was measured via heat precipitation and the Abaxis VSPro equine Fibrinogen cartridge to determine reference intervals, and in an attempt to validate the VSPro for use in avian species. Abaxis VS2 Avian/Reptile Chemistry panel, iSTAT CG4+, and iSTAT Chem8+ results in addition to body condition score, spun PCV, cloacal temperature and fibrinogen were measured. Proposed reference intervals for brown pelicans are presented. Fibrinogen results were not comparable between the gold standard method and the VSPro, indicating that the VSPro is not appropriate for use in brown pelicans.

An easy and short-time TLC-densitometric method was developed for the separation of metronidazole, secnidazole, ornidazole, tinidazole, and 2-methyl-5-nitroimidazole and for the determination of metronidazole and tinidazole in Metronidazole Polpharma and Tinidazolum Polpharma tablets. Analyzes were performed on chromatographic plates precoated with silica gel 60F254 using the optimal mobile phase: chloroform + methanol + diethylamine in a volume ratio of 9:1:1. The method has been validated. The intraday and interday precision values for the three different concentrations ranged from 0.99% to 1.48% and 0.89% to 1.76%, and the precision values ranged from 1.13% to 2.48% and 0.95% to 2.49% for metronidazole and tinidazole, respectively. The limit of quantification (LOQ) was 0.036 and 0.066 µg/spot for metronidazole and tinidazole, respectively. The mean recovery was 103.1% and 100.6% for metronidazole and tinidazole, respectively. The content of metronidazole and tinidazole in tablets in relation to the content declared by the manufacturer was 101.3% and 99.8%, respectively. The obtained results were verified using the pharmacopoeial method. The presented method is fast, sensitive, precise, selective, accurate and robust. It allows for the analysis of several samples on one chromatography plate at the same time.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

Background and objectives: Lipoid proteinosis (LP) is an autosomal recessive transfer lysosomal storage disease, characterised by the accumulation of hyalin substance in the mucous membranes, skin, internal organs and brain, for which there is no biochemical diagnostic method. The aim of this study was to determine the carnitine and acylcarnitine metabolic profile with LC-MS/MS in LP patients and thereby examine the potential of this as a new biochemical method in the determination of biochemical markers in LP patients. Materials and Methods: In this study, 27 carnitine and acylcarnitine esters were measured with LC-MS/MS in serum samples taken from 14 healthy control subjects and 14 patients who presented at the Skin and Venereal Diseases Polyclinic and were diagnosed with LP as a result of clinical, radiological and histopathological examinations. Results: The results of the study showed that C0 (free carnitine) C3, C4, C4:DC, C5DC, C6, C8, C14:1, C14:2, C16 and C18 acylcarnitines were statistically significantly reduced in the LP patients (p<0.05, p<0.01). Conclusions: It was concluded that the application of carnitine profile screening, which is an inexpensive, rapid and reliable method, could make a contribution to the differential diagnosis as aa supporting laboratory test in individuals with suspected LP.

Dietary supplements are more and more often used to increase daily intake of essential vitamins and minerals. These preparations are classified as special category of foods and are subject to food law, not pharmaceutical regulations. As a result the requirements to dietary supplements are much less restrictive than to medications. Also simple and inexpensive procedure of registration causes that the number of dietary supplements is widely spread every year. On every manufacturing phases of dietary supplements, there is a risk of contamination. One of the pollutions might be mercury which is classified as heavy metal. Its inorganic compounds damage kidneys and liver and methylmercury is easily absorbed from gastrointestinal system. Methylmercury is distributed in all tissues, also in nervous system. The aim of study was to determine the level of mercury in multivitamins and multiminerals preparations and to analyze the results. The study included 22 dietary supplements containing vitamins and minerals available on Polish market. Mercury was analyzed with atomic absorption spectrometry using AMA 254. The concentrations of Hg was 0.22–5.85 µg/kg (the average content was 2.40 µg/kg). The highest average mercury content was 4.51 µg/kg, whereas the lowest one was 0.31 µg/kg. The results was also analyzed in individual groups depending on main component and indication for use as well as pharmaceutical formulation. Also according to manufacturer’s recommendation, the dose of mercury taken with a single medicine was estimated for time of a day, a week, a month, 3 months and also a year. The findings were compared to limits defined in regulations of European Union and PTWI set by JECFA to assess the health risk. The results presented in this study proved that the amount of mercury in tested dietary supplements is much lower than the value of valid regulations. Analyzed supplements as long as they are used with the recommendation of manufacturer, do not pose a threat to human health.

A rapid, precise, accurate and low cost method for the determination of vitamin E (α-tocopherol) in cereal products and biscuits was developed. The uncertainty was calculated for the first time and the methods were performed in different cereal products and biscuits, characterized as “superfoods”. The limits of detection and quantification were calculated. Accuracy and precision were estimated using the certified reference material FAPAS T10112QC and the determined values were in good accordance with the certified values. The health claims according to the daily reference values for vitamin E were calculated and the results proved that the majority of the samples examined showed %daily value higher than 15%.

Traditional metals such as stainless steel, titanium and cobalt chrome are used in biomedical applications (implants, scaffolds etc.) but suffer from issues such as osseointegration and compatibility with existing bone. One way to improve traditional biomaterials is to incorporate ceramics with these metals so that their mechanical properties can be similar to cortical bones. Tricalcium phosphate is such a ceramic with properties so that it can be used in human body. This research explores the use of binder jetting based additive manufacturing process to create a novel biocomposite made of cobalt chrome and tricalcium phosphate. Experiments were conducted and processing parameters were varied to study their effect on the printing of this biocomposite. Layer thickness, binder saturation and drying time affected the dimensional tolerance and the density of the green samples. This effect is important to understand so that the material can be optimized for use in specific applications.

The purpose of this study is to determine the equilibrium conditions for the formation of a mixture of propane and normal butane hydrates including temperature, pressure and mole fraction. In order to prevent the formation of hydrates in the cooling path, it is necessary to examine the conditions of hydrate formation and provide solutions. Modeling of hydrate formation conditions was performed using Hydoff software and compared with experimental results in this field, which obtained an acceptable error percentage. The range of temperature is between 267-276 °C and the molar percentage of propane is 0.7,0.8 and 0.9 and the mathematical equation was presented to predict hydrate formation. By analyzing the results, it was found that by increasing the concentration of ethane in the presence of other compounds, hydrate growth increased and hydrates formed more stable, also by increasing the concentration of propane and normal butane the amount of equilibrium pressure will decrease.

Permafrost thaw is an important aspect of Earth’s carbon cycles. Initial estimates suggest that permafrost thaw could contribute anywhere between 20 to 500 Gt of CO2-eq by 2100. These estimates are all fundamentally centered around one number: active layer thickness (ALT). The deeper the ALT, the more emissions. Unfortunately, ALT is a highly spatially heterogeneous number and determined by numerous thermal, soil hydrology, and geomorphological effects. The remotely sensed active layer thickness (ReSALT) algorithm was introduced in 2010 to provide scientists with a way to model ALT heterogeneously at meter-scale resolution. However, upon inspection, this work shows that ReSALT’s modeling approach is self-inconsistent when using a variable soil porosity model. This work then introduces SCReSALT (Self-Consistent ReSALT) to solve that problem. Experimental comparisons to a past study in Utqiagvik (formerly Barrow), Alaska show significant improvement and suggest that SCReSALT should become a standard tool in permafrost thaw modeling. Code to reproduce all results can be found at https://github. com/jmathur25/permafrost-prediction.

The aim of this research is to investigate the influence of model height employed in the deep drawing of orthodontic aligner sheets on force transmission and aligner thickness. Forty sheets (Zendura FLX) were thermoformed over four models of varying heights (15, 20, 25, and 30 mm). Normal contact force generated on the facial surface of the upper right central incisor (Tooth 11) was measured using pressure-sensitive films. Aligner thickness around Tooth 11 was measured at five points. A digital caliper and a micro-computed tomography (µ-CT) were employed for thickness measurements. The normal contact force exhibited an uneven distribution across the facial surface of Tooth 11. Model 15 displayed the highest force (88.9±23.2 N), while Model 30 exhibited the lowest (45.7±15.8 N). The force distribution was more favorable for bodily movement with Model 15. Thickness measurements, conducted using a digital caliper and µ-CT, revealed substantial thinning of the aligner after thermoforming. This thinning was most pronounced at the incisal edge (50% of the original thickness) and least at the gingivo-facial part (85%). Additionally, there was a progressive reduction in aligner thickness with increasing model height, which was most significant on the facial tooth surfaces. We conclude that the thermoplastic aligner sheets undergo substantial thinning during the thermoforming process, which becomes more pronounced as the height of the model increases. As a result, there is a decrease in both overall and localized force transmission, which could lead to increased tipping by the aligner and a diminished ability to achieve bodily movement.

Two-dimensional (2D) materials show advantages as surface enhanced Raman scattering (SERS) substrate over traditional noble metals, such as chemically inert flat surface and uniform SERS signals. However, due to the low density of free electrons of 2D materials, the enhancement mechanism is mainly restricted to chemical enhancement instead of electromagnetic enhancement, resulting a relatively low enhancement factor. In this work, we reported a sensitive 2D SERS substrate based on chemical vapor deposited MoN nanosheets with electromagnetic enhanced mechanism. The maximum enhancement factor can be 3×105 with a limit of detected concentration of 4×10-8 M, which is comparable to those noble metal SERS substrates without hot spots. The MoN nanosheets show strong surface plasmon resonance in the visible range as evidenced by the UV-vis absorption spectroscopy and first principle calculation. The MoN nanosheets SERS substrates exhibit excellent Raman signal uniformity within the nanosheets. Meanwhile, Distinct thickness dependent sensitivity was observed in the MoN nanosheets, higher sensitivity can be achieved by decreasing the thickness of the nanosheets. Furthermore, the MoN nanosheets SERS substrate also show high thermal stability, which can be annealed in air for more than 300℃ and maintain its SERS activity. The high stability of MoN nanosheets allows it to be reused for 20 cycles without obvious signal decay. The high sensitivity, stability, reusability and Raman signal uniformity, makes MoN nanosheets an ideal 2D SERS substrate for practical applications.

The process of full-thickness skin regeneration is complex and has many parameters involved, which makes it difficult to use a single dressing to meet the various requirements of the complete regeneration at the same time. Therefore, developing hydrogel dressings with multifunction, including tunable rheological properties and aperture, hemostatic, antibacterial and super cytocompatibility, is a desirable candidate in wound healing. In this study, a series of complex hydrogels were developed via the hydrogen bond and covalent bond between chitosan (CS) and alginate (SA). These hydrogels exhibited suitable pore size and tunable rheological properties for cell adhesion. Chitosan endowed hemostatic, antibacterial properties and great cytocompatibility and thus solved two primary problems in the early stage of the wound healing process. Moreover, the sustained cytocompatibility of the hydrogels was further investigated after adding FGF and VE-cadherin via the co-culture of L929 and EC for 12 days. The confocal 3D fluorescent images showed that the cells were spherical and tended to form multicellular spheroids, which distributed in about 40-60μm thick hydrogels. Furthermore, the hydrogel dressings significantly accelerate defected skin turn to normal skin with proper epithelial thickness and new blood vessels and hair follicles through the histological analysis of in vivo wound healing. The findings mentioned above demonstrated that the CS/SA hydrogels with growth factors have tremendous potential as multifunctional hydrogel dressings for full-thickness skin regeneration incorporated with hemostatic, antibacterial, sustained cytocompatibility for 3D cell culture and normal skin repairing.

This article presents, for the first time, the kinetics and the general conversion features of a 3-initiator system (A/B/N), based on proposed mechanism of Mokbel et al, for both free radical polymerization (FRP) of acrylates and the free radical promoted cationic polymerization (CP) of epoxides using copper complex as the initiator. Higher FRP and CP conversion can be achieved by co-initiators concentration [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals S' and S. The FRP and CP conversion is proportional to, respectively, the nonlinear and linear power of bI[A][B], where b and I are the absorption coefficient and the light intensity, respectively. System in air has lower conversion than in laminate due to the oxygen inhibition effects. For thick samples (with thickness z), there is an optimal concentration [A*] which is inverse proportional (bzI), in contrast with very thin sample, in which the conversion is an increasing function of [A] and [B]. The unique feature of dark polymerization in CP conversion enables the polymerization to continue in living mode, in contrasts with that of the radical-mediated pathway in most conventional FRP. The measured results of Mokbel et al are well analyzed and matching the predicted features of our modeling.

This study reports a correlation between EEG and structural brain changes in patients after severe traumatic brain injury in a coma. The novelty of our approach was based on the combination of structural visualization (MRI) and functional neuroimaging (EEG) during tactile stimulation. The structural morphometry indicated a decrease of whole-brain cortical thickness, the gray-matter volume of the cortex, and subcortical structures in comatose patients compared to healthy subjects. In resting-state EEG, coma patients had significantly higher power of the slow-wave activity of 2-6 Hz and significantly less power of the alpha and beta rhythm. Importantly, coma patients showed a significant decrease of theta-rhythm power in tactile stimulation compared to the resting state, and this EEG pattern was not found in the control group. The decrease of the theta-rhythm power significantly correlated with the better outcome from a coma. Spectral changes in EEG in response to tactile stimuli showed no association with brain morphometric measures in healthy controls. In patients, decreasing theta-rhythm power correlated positively with the volume of whole-brain gray matter, right putamen, and insula; and negatively with the volume of damaged brain tissue. Increasing beta-rhythm power, specific tactile EEG response for a healthy brain, correlated with the cortical thickness of the somatosensory Paracentral and Precentral area. The observed decrease of gray-matter volume indicates brain atrophy in coma patients, which could be associated with neurodegeneration induced by injury. Our results also demonstrate that slow-wave desynchronization, as a nonspecific response to tactile stimulation, can serve as a sensitive index of morphometric changes after brain injury and coma outcome.

A study about influence of heat input on welding defects in vertical upward welding position for dissimilar material and thickness using a new variation of TIG welding torch is done with support of advanced inspection methods SEM and EBSD. With vertical upward welding position, control heat input plays an important role to keep the weld stabilization without defects. On the other hand, TIG welding process using a conventional TIG torch (conventional TIG welding process) has low efficiency and it is difficult to control heat input with high accuracy. So, it is considered that using conventional TIG torch is still a challenge for welding thin plates. In this case, a new variation of TIG torch has been developed. This torch used a constricted nozzle to improve plasma arc characteristics. As a result, it can control efficiently the heat input to prevent the excessive or insufficiency for joining thin sheets. For evaluation of welding quality, advanced examination methods SEM and EBSD were applied to directly observe the welding defects. From the results, the formation mechanism of blowhole inside weld zone in case of welding dissimilar material and thickness was discussed. It is pointed out that when sufficient welding current, the change from weld zone to base metal is uniform, no welding defects such as blowhole was seen. However, in case of low welding current, the thinner base metal is insufficient fusion and the change between weld zone and base metal is not uniform. The blowhole was observed at SS400 material side.

Lewis et al. published an important and timely necessary article about the determination of death by neurological criteria, revising the Uniform Determination of Death.The acceptance of brain death (BD) has been progressively accepted beginning at the late 1950s. Nonetheless, contentious brain-death cases have recently raised new controversies about the diagnosis of BD, such as the Jahi McMath case, extensively covered by the US and international press. Jahi McMath meant a terrible tragedy for her and her family. But further than this gloomy story, the case has also raised confusion and challenging qualms about a fundamental query: how we confirm whether a person is dead or alive? Since 1981, the Uniform Determination of Death Act (UDDA) has served as the legal foundation for the medical practice of determining death. But, although death by neurologic criteria is considered legal death throughout the United States, several recent lawsuits have quizzed the rightfulness the authority of the UDDA to declare death by neurological criteria. This issue explains the importance of Lewis’s et al. paper. In this article I want to present the historical procedure for issuing a law in Cuba for the determination and certification of death. Of course, it is impossible to compare our country with USA. Cuba is a small and developing country, in which a law encompasses a national scenery, in contrast with USA, a multistate nation.

The unique qualities of areas with natural landscape features help provide sustainability. Moreover, their different vegetation covers and ecosystems contribute to the preservation of their visual attraction. In recent years, the demand for natural areas has not only been seen at a recreational level, but has also become associated with the conservation and sustainability of those areas. Although the concept of sustainability is expressed from an ecological point of view, studies indicate that the visual aspect is also an important component. Thus, in this study, a visual quality assessment was carried out which considered both objective and subjective evaluations of different habitat types. Efteni lake-wetland and Melen Ağzı dunes (Düzce), Anzer, Ayder, and Çat Düzü highlands (Rize), and Sultanmurat and Taşli highlands (Trabzon) were selected as the study areas. A visual quality analysis was conducted with a total of 43 participants (23 students, 16 local inhabitants and four lecturers) in order establish their preferences in areas with different landscape characteristics. For the determination of the visual qualifications of these areas, a total of 24 photographs showing typical images representing each habitat type (three photographs for each) were employed. Taking perceptual parameters into consideration, assessment of visual quality was made according to the points given to each photo by the participants. Consequently, differences in visual quality were found to be influenced by the demographic status of the participants, differences in habitat types, recreational trends and the conservation status of the habitats.

The importance of irrigation in boosting agricultural production and productivity is widely understood. Proper planning and effective and efficient management and operation of irrigation system require crop and site-specific data. Since the last few years, Ethiopia has embarked on expansion of irrigated wheat. However, crop-specific data useful for irrigation planning and management for wheat crop is limited. The objective of this research was to determine water requirements and crop coefficients for wheat crops based on field measurements. The research was carried out at the Debre Zeit Agricultural Research Center in central Ethiopia during the dry season (Bega) of 2021/22. The crop considered for the experiment was durum wheat of the Utuba variety. Two non-weighing lysimeter units were employed to measure the water balance components. The soil moisture was monitored using gravimetric method on daily basis conducted both before and after each irrigation event at various depth intervals. The crop required a total of 115 days to fully mature. The length of the growth of initial, development, mid, and late stages were about 20, 30, 42, and 23 days, respectively. Microsoft Excel was used for the data analysis and the CropWAT8.0 model to estimate the reference evapotranspiration. Crop evapotranspiration (ETc) was determined using the water balance equation, and crop coefficients were computed from ETc and reference evapotranspiration (ETo). The results indicate that the total seasonal water requirement of the crop was 392.75mm. The growth stage-based water requirement was 40.35 mm, 82.44 mm, 238.66 mm, and 31.3 mm during the initial, development, mid, and late growing stages, respectively. For the initial, development, mid, and late stages of wheat growth, the crop coefficient was calculated to be 0.51, 0.83, 1.29, and 0.52, respectively. It was found that a fourth-degree polynomial equation fits well and explains the relationship between day of growth stage and kc of the crop. Although a one-season measurement, the results generated here could be useful for crop-specific data in scarce areas.

Plant reproduction is a very important process on Earth from the perspective of biodiversity, biomass gain and crop productivity. It is therefore important to understand sex determination process and many researchers are investigating the molecular basis of this phenomenon. However, information on the influence of transcription factors (TFs) on this process is limited, although cucumber is a model plant in this regard. In the present study, based on RNA-seq data for differential gene expression (DEG) analyses, we aimed to investigate the regulatory TFs that may influence the metabolomic processes in the shoot apex containing the forming flower buds. Therefore, a robust TF database was established for the B10v3 cucumber genome. Sex-specific interactome network maps were generated, indicating the regulatory TFs by their effects on DEGs and further on processes leading to the formation of different sex flowers. The network analysis identified major families of regulatory TFs. The most abundant families were: MYB, AP2/ERF, NAC and bZIP, and those with the greatest impact on developmental processes were identified, namely the AP/ERF family, followed by DOF, MYB, MADS and others. Thus, the central nodes and key regulators in the networks were identified with respect to male, female and hermaphrodite. Here, we proposed the first model of the regulatory network of TFs that influences the metabolism of sex development in cucumber. These findings may help to understand the molecular genetics and functional mechanisms underlying sex determination processes.

In this work, unmodified screen-printed electrode (bare SPE) and Sb-film modified SPE (SbFSPE) sensors were employed for the analysis of trace amounts of Pb(II) in non-deaerated water solutions. The modified electrode was performed in situ in 0.5 mg/L Sb(III) and 0.01 M HCl. The methodology was validated for an accumulation potential of –1.1 V vs. Ag/AgCl and an accumulation time of 60 s. A comparative analysis of bare SPE and SbFSPE showed that the detection and quantification limits decrease for the bare SPE. The method with the bare SPE showed a linear response in the 69.8–368.4 µg/L concentration range, whereas linearity for the SbFSPE was in the 24.0–319.1 µg/L concentration range. This work also reports the reason why the multiple standard addition method instead of a linear calibration curve for Pb(II) analysis should be employed. Furthermore, the analytical method employing SbFSPE was found to be more accurate and precise compared to the use of bare SPE when sensors were employed for the first time, however this performance changed significantly when these sensors were reused in the same manner. Furthermore, electrochemical impedance spectroscopy was used for the first time to analyse the electrochemical response of sensors after being used for multiple successive analyses. Surface characterisation before and after multiple successive uses of bare SPE and SbFSPE sensors, with atomic force microscopy and field emission scanning electron microscopy, showed sensor degradation. The interference effect of Cd(II), Zn(II), As(III), Fe(II), Na(I), K(I), Ca(II), Mg(II), NO₃^– Bi(III), Cu(II), Sn(II), and Hg(II) on the Pb(II) stripping signal was also studied. Finally, the application of SbFSPE was tested on a real water sample (from a local river), which showed high precision (RSD = 8.1%, n = 5) and accurate results.

Investigation of the methanol extract of the poroid fungus Fuscoporia torulosa resulted in the isolation of a novel triterpene, fuscoporic acid (1) together with inoscavin A and its previously undescribed Z isomer (2 and 3), 3,4-dihydroxy-benzaldehide (4), osmundacetone (5), senexdiolic acid (6), natalic acid (7), and ergosta-7,22-diene-3-one (8). The structures of fungal compounds were determined on the basis of NMR and MS spectroscopic analysis, as well as molecular modelling studies. Compounds 1, 6-8 were examined for their antibacterial properties on resistant clinical isolates, and cytotoxic activity on human colon adenocarcinoma cell lines. Compound 8 was effective against Colo 205 (IC50 11.65±1.67 µM), Colo 320 (IC50 8.43±1.1 µM) and MRC-5 (IC50 7.92±1.42 µM) cell lines. Potentially synergistic relationship was investigated between 8 and doxorubicin, which revealed a synergism between the examined compounds with a combination index (CI) at the 50% growth inhibition dose (ED50) of 0.521±0.15. Several compounds (1, and 6-8) were tested for P‐glycoprotein modulatory effect in Colo 320 resistant cancer cells, but none of the compounds proved to be effective in this assay. Fungal metabolites 2-5 were evaluated for their antioxidant activity using the oxygen radical absorbance capacity (ORAC) and DPPH assays. Compounds 4 and 5 proved to possess considerable antioxidant effect with EC50 0.25±0.01 (DPPH) and 12.20±0.92 mmol TE/g (ORAC). The current article provides valuable information on both chemical and pharmacological profiles of Fuscoporia torulosa, paving the way for future studies with this species.

Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

Techniques of stripping voltammetry (SV) determination of silver and gold in pyrites and carbonaceous matter were developed. The problem of quantitative transfer of the sample into the solution was solved. For this purpose, the ore matrix of carbonaceous shales was decomposed by mineral acids in autoclaves at high pressures. The element to be determined from the sample matrix was separated by extraction. Ag(I) ions from the solutions were extracted in the form of dithizonate complex in CCl₄. Au(III) ions were extracted by diethyl ether. The extracts were decomposed thermally. The dry residue was dissolved in the background electrolyte, and the element was determined by the SV method. The graphite electrode (GE) impregnated with polyethylene was used as a working electrode in SV–determination of silver. SV–determination of gold was carried out using GE modified by bismuth. The limits of detection (LOD) of Ag(I) and Au(III) contents were equal to 0.016 mg L^-1 and 0.0086 mg L^-1, respectively. The results of SV-determination of gold and silver in standard samples, pyrites and carbonaceous shales were presented. The silver content in the pyrite was 13.6 g t^-1, in carbon shale—0.34 g t^-1. The concentration of gold in the pyrite ore zone "Kirovsko–Kryklinskaya" was 1.15 g t^-1; in carbonaceous shales—2.66 g t^-1. The obtained data were consistent with the data of atomic emission spectroscopy (AES) and inductively coupled plasma mass spectrometry (ICP—MS). The error of determination of elements by stripping voltammetry was calculated when determining the silver content of 10...6 g t^-1 in pyrite and carbonaceous material, which was less than 12%, and when determining the gold content of 1...3 g t^{- 1} in pyrite and carbonaceous matter, which was less than 23%.

The present state of the natural environment is significantly influenced by the construction sector. Due to the large amounts of consumed natural resources and materials as well as the high volume of emitted pollutants, the building industry is considered to have a key influence in achieving a global sustainable development. A considerable part of the ecological impact of the built environment is influenced by the energy consumed for creating appropriate indoor conditions as well as by the greenhouse gases that are emitted during the operation stage of a building’s life cycle. Therefore, the energy performances of existing buildings must be significantly improved in the near future. This paper analyzes the influence of the thermal insulation thickness of walls on the linear thermal transmittances and the heating demand of an existing building. The resulted values show that while increasing the insulation of the walls leads to a serious heat demand reduction, a deep renovation of the building cannot be achieved solely by using this solution.

Atrial fibrillation (AF) is a common cardiac arrhythmia associated with significant morbidity and mortality. The role of epicardial adipose tissue (EAT), particularly in the left atrium, has garnered attention in the pathophysiology of AF. This review aims to provide an overview of the association between the thickness of left atrial epicardial adipose tissue (LA-EAT) and the incidence of AF, while exploring the arrhythmogenic effects of LA-EAT and the impact of epicardial fat tissue changes with age and in pathological conditions. A comprehensive search of PubMed was conducted, and relevant studies were selected based on their inclusion criteria. The findings suggest that increased LA-EAT thickness is associated with an elevated risk of AF, potentially mediated through inflammatory and proarrhythmic effects. Age-related changes in epicardial fat tissue and alterations in pathological conditions, such as obesity, metabolic syndrome, and cardiovascular diseases, further contribute to the development and progression of AF. Further research is needed to deepen our understanding of these mechanisms and their clinical implications.

In this paper, we consider the temporal development of the optical density of the H$_\alpha$ spectral line in a hydrogen laser induced plasma. This is achieved by using the so-called duplication method in which the spectral line is re-imaged onto itself and the ratio of the spectral line with it duplication is taken to its measurement without the duplication. We asses the temporal development of the self-absorption of the H$_\alpha$ line by tracking the decay of duplication ratio from its ideal value of 2. We show that when 20% loss is considered along the duplication optical path length, the ratio is 1.8 and decays to a value of 1.25 indicating an optically thin plasma grows in optical density to an optical depth of 1.16 by 400 ns in the plasma decay for plasma initiation conditions using Nd:YAG laser radiation at 120 mJ per pulse in a 1.11$\times10^{5}$ Pa hydrogen/nitrogen gas mixture environment. We also go on to correct the H$_\alpha$ line profiles for the self-absorption impact using two methods. We show that a method in which the optical depth is directly calculated from the duplication ratio is equivalent to standard methods of self-absorption correction when only relative corrections to spectral emissions are needed.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

Cerebral aneurysms come in a wide range of shapes and sizes, they can evolve over time and present significant changes. It is generally accepted that large aneurysms are more prone to rupture, but the rupture of small aneurysms has also been observed, indicating the presence of additional risks factors. The aim of this study is to assess the effects of the aneurysm size and wall thickness on its rupture risk by using fluid-structure interaction simulations. Six patient-specific geometries were chosen, four were used for studying the size effect and two for studying the thickness effect. Additional cases where the aneurysm was removed were included. It was found that thinner walls suffer from significantly greater stresses, whereas an increment in size means, in general, lower wall shear stress and greater equivalent stress. By removing the aneurysm, it could be noted that at the rupture point, the reduction in the time-averaged wall shear stress was 75%. Although the size of an aneurysm has a great impact in its rupture risk, its wall thickness needs to be considered, since even maintaining its size, the aneurysm could suffer from a thin-ning of its walls that can lead to structural failure.