We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

The characteristics of gap plasmon formed by nanoparticle-on-mirror (NPOM) structure composed of metal nanoparticles (MNP) and metal thin films have aroused the interest of various optoelectronic devices. The resonant spectrum obtained by the internal coupling effect of gap can be flexibly controlled by the polarization of incident light and the thickness of the dielectric layer between MNP and metal thin films. We have theoretically studied the resonance spectra of polarization-dependent gold ellipsoidal nanoparticles (GENP) and gold thin films in the gap region of NPOM structures. GENP and gold thin films are separated by a dielectric layer with a refractive index of 1.36. We observe that the intensity of the local electric field resonance peak in the gap region is inversely proportional to the polarization angle. Similarly, the intensity of the local electric field resonance peak in the gap region is inversely proportional to the thickness of the dielectric layer. We have obtained more than 2200 V/m local electric field intensity (dielectric layer thickness 0.3nm). Finally, the resonant peak wavelength of the electric field in the gap region of the NPOM structure is also controlled by the polarization angle of the incident light and the thickness of the dielectric layer.

Nowadays asymmetric thin film composite (TFC) polymeric hollow fiber (HF) membranes are extensively used in industrial gas/vapor separations, water treatment etc. There are numerous advantages to use hollow fibers such as: low energy requirements, simplicity of operation, and high specificity. In the present article we discuss the progress made during the past decade in the preparation of the HF substrate and preparation/modification of the thin selective layer. Their applications in water treatment, dehydration of alcohols via pervaporation and gas/vapor separation are also demonstrated.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO2 thin films were elucidated using real-time synchrotron radiation imaging, its structure determined using grazing incidence X-ray diffraction (GIXRD), its morphology imaged using the field emission scanning electron microscopy (FESEM), and its surface topography examined using the atomic force microscope (AFM) in contact mode. Cubical white spots were detected, identified as Ag, while the TiO₂ thin film resembles a porous ring-like structure with each ring coalescing and forming channels. Junction growth is directly proportional with time under continuous heating conditions (annealing), and its growth orientations and patterns were seemingly random.

In the last years, advances in materials engineering based on adaptive electronics have found a new paradigm to optimize drawbacks in signal processing. A two-layer MnO/ZnO:Zn heterostructure envisioned for frequency adaptive electronic signal processing is synthesized by sputtering where the use of internal states allows reconfigurability to obtain new operating modes at different frequency input signals. An X-Ray Diffraction (XRD) is performed on each layer, MnO:Mn had a cubic and ZnO:Zn a hexagonal structure with preferential growth in [111] and [002] directions respectively. It is determined that the coupling in this heterojunction is compatible with a mismatch less 1 % due texture in each layer which implies a low number of defects. An electrical characterisation with an oscilloscope and signal generator was carried out to obtain the time-response signals and current-voltage (I-V) curves where no degradation is detected when changing from a range of frequencies (100 Hz – 1 MHz). An equivalent circuit is proposed to explain the effects in the interface. Finally, the MnO/ZnO:Zn heterojunction delivers states that are stable, repeatable, and reproducible and it demonstrates how the interaction of the materials can be used in adaptive device applications applying frequencies and internal states as to create new and innovative design schematics, reducing the numbers of components/connections in a system for future sustainable electronics.

The organic solar cells (OSCs) have drawn attention in the past decade due to its cynosure in industrial manufacturing because of its promising properties such as low weight, highly flexible and low cost production. However, low η restricts the utilization of OSCs for potential application such as low cost energy harvesting devices. In this paper, OSCs structure based on triple junction tandem scheme is reported with three different absorber materials with the objective to enhance the absorption of photons which in turn improves the η, as well as its correlating performance parameters. The investigated structure gives the higher value of η = 14.33% with Jsc=16.87 (mA/m2), Voc=1.0 (V), and FF=84.97% by utilizing a stack of three different absorber layers with different band energies. The proposed structure is tested under 1.5 (AM) with 1 sun (W/m2). The impact of top, middle and bottom sub cells thickness on η is analyzed with a terse to find the optimum thickness for three sub cells to extract high η. The optimized structure is then tested with different electrode combination and the highest η is recorded with FTO/Ag. Moreover, the influence of upsurge temperature is also demonstrated on the proposed structure and observed that the upsurge temperature has greatly affected the electrical parameters of the device and η decreases from 14.33% to 11.40% when the temperature of the device rises from 300-400 K.

The light response and resistance switching behavior in BaTiO3 (BTO) films are studied for a symmetric Pt/BTO/Pt structure. The resistance of films as a function of time with and without ultraviolet light has been studied. Furthermore, resistance switching behavior was clearly observed based on the application of 365 nm wavelength ultraviolet light. Consequently, the polarities of resistance switching can be controlled by ultraviolet light when the energy is larger than the band excitation energy. It is proposed that the polarity of the resistance switching is dictated by the competition of the ferroelectricity and oxygen vacancy migration. This provides a new mechanism for modulating the state of ferroelectric resistive memory devices.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

Light sources tend to affect images captured in any automatic optical inspection (AOI) system. In this study, the effectiveness of metal-halide lamps, quartz-halogen lamps, and LEDs as the light sources in AOI systems for the detection of the 3rd and 4th layers electrodes of thin-film-transistor liquid crystal displays (TFT-LCDs) is examined experimentally. The results show that the performance of LEDs is generally comparable or better than that of metal-halide and quartz-halogen lamps. The best optical performance is by the blue LED due to its spectrum compatibility with the time-delay-integration charged-coupled device (TDI CCD) sensor and its better spatial resolution. The images revealed by the blue LED are sharper and more distinctive. Since current LEDs are more energy efficient and environmentally friendly, using LEDs as the light source for AOI is very beneficial. As the blue LED performs the best, it should be adopted for AOI using TDI CCD sensors.

Near space environment is the airspace at an altitude of 20 km-100 km, where complex conditions such as low temperature, low pressure, high wind speed and solar radiation exist. As one of the important meteorological parameters, temperature is crucial for space activities, but the influence of the complex environment makes the error of conventional temperature measurement methods large. Therefore, a new microbridge temperature sensor was designed that can reduce solar radiation and achieve a fast response. And through simulation analysis, the three factors influencing the temperature errors of Joule heat, solar radiation heat and aerodynamic heat were investigated. And the influence of temperature error is reduced by optimizing the installation position of the sensor. Through the temperature error model, the error value in the actual measurement value is removed, to realize the high accuracy detection of near-space temperature.

We investigated the effect of 0.6 MeV proton irradiation on the superconducting and normal state properties of thin-film YBa2Cu3O7−δ superconductors. A thin-film YBCO superconductor (≈ 567 nm thick) was subject to a series of proton irradiations with a total fluence of 7.6×1016p/cm2. Upon irradiation, Tc was drastically decreased from 89.3 K towards zero with a corresponding increase in its normal state resistivity above Tc. This increase in resistivity which indicates the increase of defects inside the thin-film sample can be converted to the dimensionless scattering rate. We found that the relation between Tc and dimensionless scattering rate obtained during proton irradiation approximates the generalized d-wave Abrikosov-Gor’kov theory better than the previous results obtained from electron irradiations. This is an unexpected result since the electron irradiation is known to be most effective to suppress superconductivity over other heavier ion irradiations such as proton irradiation. It suggests that the type of defects created by proton irradiation evolves from cascade defects (in bulk single crystals) to point-like defects (in thin-film single crystals) as the thickness decreases.

Infrared sensors incorporating suspended zinc oxide (ZnO) pyroelectric films and thermally-insulated silicon substrates are fabricated using conventional MEMS-based thin-film deposition, photolithography, and etching techniques. The responsivity of the pyroelectric film is improved through annealing at 500℃ for 4 h. The voltage response of the fabricated sensors is evaluated experimentally for a substrate thickness of 1 µm over a sensing range of 30 cm. The results show that the voltage signal varies as an inverse exponential function of the distance. A positioning system based on three infrared sensors is implemented in LabVIEW. It is shown that the position estimates obtained using the proposed system are in excellent agreement with the actual locations. In general, the results presented in this study provide a useful source of reference for the further development of MEMS-based pyroelectric infrared sensors.

The lithium-ion batteries are widely used as a power source for portable devices, including cell phones. The useful life is about 2 years or 500 cycles, contributing to the generation of waste from electrical and electronic equipment (WEEE). Mining of lithium and cobalt damages the environment and is onerous; therefore, sustainable alternatives, such as obtaining these elements from secondary sources as recycling of lithium-ion batteries, are essential to provide the inputs used in the sector. However, the metallurgical route which will used to recovering them must be considered, due to this work aims for a more environmentally favorable process using DL-malic acid 1.5 M and instead of compared with sulfuric acid 2 M, heat pretreatment of 1 h and 3 h, and for all conditions, experiments were carried out with and without adding the oxidizing agent hydrogen peroxide. The best yields occurred in presence of H2O2 10 % v/v, and heat pretreatment of 1 h: 33.49 % Co and 4.63 % Li, and 29.78 % Co e 3.44 % Li were recovered by sulfuric acid and DL-malic acid, respectively.

Epithelial–mesenchymal transition (EMT) is defined as a cellular process during which epithelial cells acquire mesenchymal phenotypes and behavior following the downregulation of epithelial features. EMT and its reversed process, the mesenchymal-epithelial transition (MET), and the special form of EMT, the endothelial-mesenchymal transition (EndMT), have been thought as a universal dogma controlling developmental and pathological processes. More than half a century of EMT study has made it a large research field and a mainstream concept. However, discrepancies and disputes over EMT and EMT research have also grown over time. Particularly, neither the epithelial and mesenchymal states/properties nor their regulatory networks nor specific markers have been defined, rendering the EMT, MET and EndMT concepts groundless. Moreover, EMT and MET effects should not be a cause, but rather a consequence of or an accompanying effect during developmental and pathological processes. EMT and MET represented by the change in cell shapes or adhesiveness or symbolized by EMT factors are biased interpretation of the overall change in cellular property and regulatory networks during development and cancer progression. The true meaning of EMT effects in some developmental and pathological processes, such as fibrosis, needs re-evaluation. But the core EMT factors are actually a few components of the regulatory networks of neural stemness, which determines tumorigenicity and pluripotency. The EMT effects in cancer progression and neural crest formation are wrong attribution of the role of neural stemness during cancer progression and the cell-intrinsic property of neural crest cells to the unknown mesenchymal state. It is time to reassess the significance of EMT and its related concepts in scientific research.

The noble metals palladium and silver find use in many high performance applications, and their alloys (PdAg), known for more than sixty years, are industrially important, finding use in many fields including hydrogen purification and separation, numerous facets of catalysis, and in fuel cells. In recent years, interest in these materials has grown significantly, particularly in energy generating applications and due to their performance as solid-state chemical sensors for a range of small molecules. PdAg thin films can be prepared using traditional physical methods such as cold rolling, or more modern and controllable chemical or physical deposition techniques such as electrodeposition or chemical vapour deposition. Despite the wide-reaching uses of PdAg, several recent advancements in materials preparation, such as additive manufacturing, better known as 3-D printing, remain unexplored for this material due to the differing chemistries of the two elements. In this review, we explore the manufacturing methods commonly employed for the preparation of PdAg thin films, the common and niche applications of these materials, and opportunities for the future development of these two aspects, with an emphasis on how preparation of thin films can utilise additive manufacturing approaches.

MPC (Magneto-Photonic Crystal) Optimisation is a feature-rich Windows software application designed to enable researchers to analyze the optical and magneto-optical spectral properties of multilayers containing gyrotropic constituents. A set of computational algorithms aimed at enabling the design optimization and optical or magneto-optical (MO) spectral analysis of 1D magnetic photonic crystals (MPC) is reported, together with its Windows software implementation. Relevant material property datasets (e.g., the optical spectra of refractive index, absorption, and gyration) of several important optical and MO materials are included, enabling easy reproduction of the previously published results from the field of MPC-based Faraday rotator development, and an effective demonstration-quality introduction of future users to the multiple features of this package. We also report on the methods and algorithms used to obtain the absorption coefficient spectral dispersion datasets for new materials, for which the film thickness, transmission spectrum, and refractive index dispersion function are known.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

Germanium films were grown on c-plane sapphire with a 10 nm AlAs buffer layer using molecular beam epitaxy. The effects of Ge film thickness on the surface morphology and crystal structure were investigated by ex-situ characterization techniques. The nucleation of Ge proceeds by forming (111) oriented three-dimensional islands with two rotational twin domains about the growth axis. The boundaries between the twin grains are the origin of 0.2% strain and tilt grains. The transition to a single-grain orientation reduces the strain and results in a better-quality Ge buffer. Understanding the role of thickness on material quality during the Ge(111)/Al2O3(0001) epitaxy is vital for achieving device quality when using group IV material on the sapphire platform.

The aim of this work is to synthesis and characterize the Ta/TaN multilayer thin film coatings on 52100 tool steel under three different levels of N2 gas flow rate. The High Power Impulse Magnetron Sputtering (HiPIMS) technique was used for the deposition of Ta/TaN thin film multilayers on the substrate. Microstructure, coating thickness, composition, hardness and tribological properties of Ta/TaN multilayer coatings were characterized using scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester and pin-on-disc tester, respectively. Adhesion property was evaluated via scratch testing of the thin film thin film layer. The lowest coefficient of friction was observed with the thin film layer of higher N2 gas flow rate due to the highest adhesion value of the coating on the surface. The obtained results on hardness, adhesion and coefficient of friction properties demonstrated that this Ta/TaN multilayer thin film coating can be used for tribological applications.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

The nitrogen-doped amorphous oxide semiconductor (AOS) thin film transistors (TFTs) with double-stacked channel layers (DSCL) were prepared and characterized. The DSCL structure composed of nitrogen-doped amorphous InGaZnO and InZnO films (a-IGZO:N/a-IZO:N or a-IZO:N/a-IGZO:N) made the corresponding TFT devices exhibit quite large field-effect mobility due to the existence of double conduction channels. Especially, the a-IZO:N/a-IGZO:N TFTs showed even better electrical performance (μ_FE = 15.0 cm²·V^-1·s^-1, SS = 0.5 V/dec, V_TH = 1.5 V, I_ON/I_OFF = 1.1×10⁸) and stability (V_TH shift of 1.5, -0.5, and -2.5 V for positive bias-stress, negative bias-stress and thermal stress tests, respectively) than the a-IGZO:N/a-IZO:N TFTs. Based on the X-ray photoemission spectroscopy measurements and energy band analysis, it was assumed that the optimized interface trap states, the less ambient gas adsorption, and the better suppression of oxygen vacancies in the a-IZO:N/a-IGZO:N hetero-structures might be responsible for the better behaviors of the corresponding TFTs.

CoFe2O4 is a promissing catalytic material for many chemical reactions. We have used ab initio molecular dynamic simulations to study the structure and reactivity of the A- and B-terminations of the low index CoFe2O4 (001) surfaces to water adsorption at room temperature. Upon adsorption, water partly dissociates on both termination with a higher dissociation degree on the A- termination (30% versus 19%). The 2-fold coordinated Fe3+(tet) in the tetrahedral voids and the 5-fold coordinated Fe3+(oct) in the octahedral voids are the main active sites for water dissociation on the A- and B-termination, respectively. Molecular water, hydroxydes and surface OH resulting from proton transfer to surface oxygens are present on the surfaces. Both water free sur- face terminations undergo reconstruction. The outermost Fe3+(tet) on the A-termination and B-termination move towards the nearby unoccupied octahedral voids. In the presence of a thin film of 32 water molecules, the reconstructions are partially and completely lifted on the A- and B-termination, respectively.

A cuprous oxide (Cu₂O) thin layer served as the base for a non-enzymatic glucose sensor in an alkaline medium, 0.1 NaOH solution, with a linear range of 50-200 mg/dL using differential pulse voltammetry (DPV) measurement. An X-ray photoelectron spectroscopy (XPS) study confirmed the formation of the cuprous oxide layer on the thin gold film sensor prototype. Quantitative detection of glucose in both phosphate-buffered saline (PBS) and undiluted human serum were carried out. Neither ascorbic acid nor uric acid even at a relatively high concentration level of 100mg/dL in serum interfered with the glucose detection, demonstrating the excellent selectivity of this non-enzymatic cuprous oxide thin layer based glucose sensor. Chronoamperometry (CA) and single potential amperometric voltammetry were used to verify the measurements obtained by differential pulse voltammetry (DPV), and the positive results validated that the detection of glucose in a 0.1 M NaOH alkaline medium by DPV measurement was effective. Nickel, platinum and copper are commonly used metals for non-enzymatic glucose detection. The performance of these metal-based sensors for glucose detection using DPV were also evaluated. Cuprous oxide (Cu₂O) thin layer based sensor showed the best sensitivity for glucose detection among the sensors evaluated.

Flavonoids are secondary plant metabolites involved in biological activity that are present in plentiful proportions in many plant origin foods and beverages. Owing to their chemical difference and qualities that make them beneficial for human health, they have received a lot of focus in research. This review therefore presents an account on the chemical structure of flavonoids, food sources and their metabolism with emphasis on bioavailability. And they also examine their antioxidant, anti-inflammatory, anticancer, cardiovascular protective, neuroprotective, and antimicrobial properties and reveal related molecular processes. In addition, it overviews the clinical data concerning their possible use in the prevention and treatment of chronic diseases. Some of the problems that attend current flavonoid research are also dealt with; such issues as variation in the bioactivity of flavonoids and scarcity of clinical studies. This review is designed to present current state of knowledge and to provoke further research concerning the further potential of flavonoids in enhancing human health.

Solanum indicum Linn, is commonly known as Indian Nightshade or Poison Berry belongs to the family Solanaceae. This review studied the botanical description, traditional uses of its seeds, its chemical composition, pharmacological properties and modern applications in medicinal system. The plant is rich in alkaloids, steroidal saponins, flavonoids and phenolic acids having diverse pharmacological activities and phytochemical profile. It is used in treatment of various respiratory disorders, inflammation, skin problems and gastrointestinal disease since ancient times. Scientific research in modern times also tested many of the traditional uses revealing anti-inflammatory, antioxidant, antimicrobial activities as well as some cytotoxic and even antidiabetic effects. These pharmacological activities show potential future as uses for organic drugs, natural health products, skincare formulations and agricultural advancements.

The characterization of thin-film solar cells is of huge importance for obtaining high open-circuit voltage and low recombination rates from the interfaces or within the bulk of the main materials. Among the many electrical characterization techniques, the two- and four-wire probe using the Cascade instrument is of interest since the resistance of the wires, and the electrical contacts can be excluded by the additional two wires in 4-wire probe configuration. In this paper, both two and four-point probes configuration are employed to characterize the CIGS chalcogenide thin-film solar cells. The two-wire probe has been used to measure the current-voltage characteristics of the cell which results in a huge internal resistance. Therefore, the four-wire connection is also used to eliminate the lead resistance to enhance the characterization’s accuracy. The load resistance in the two-wire probe diminishes the photogenerated current density at smaller voltage ranges. In contrast, the proposed four-wire probe collects more current at higher voltages due to enhanced carrier collection efficiency from contact electrodes. The current conduction mechanism is also identified at every voltage region represented by the value of the ideality factor of that voltage region. It is observed that a long time given to the charge collection results in increased current density at a higher voltage. According to the results and device characteristics, a novel double-diode model is suggested to extract the saturation current density, shunt and series resistances and the ideality factor of the cells. These cells are shown to be efficient in terms of low recombination at the interfaces and with lower series resistance as the quality of the materials is in its most possible conductive form. The measured internal resistance and saturation current density and ideality factor of the two measurement configuration is measured and compared.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

Stenting is an alternative to endarterectomy for the treatment of carotid artery stenosis. However, stenting is associated with a higher risk of procedural stroke secondary to distal thromboembolism. Hybrid stents with a micromesh layer have been proposed to address this complication. We developed a micropatterned thin film nitinol (M-TFN) covered stent designed to prevent thromboembolism during carotid intervention. This innovation may obviate the need or work synergistically with embolic protection devices. The proposed double layered stent is low-profile, thromboresistant, and covered with a M-TFN that can be fabricated with fenestrations of varying geometries and sizes. The M-TFN was created in multiple geometries, dimensions, and porosities by sputter deposition. The efficiency of various M-TFN to capture embolic particles was evaluated in different atherosclerotic carotid stenotic conditions through in vitro tests. The covered stent prevented emboli dislodgement in the range of 70-96% during 30min duration tests. In vitro vascular cell growth study results showed that endothelial cell elongation, alignment and growth behaviour silhouettes significantly enhance specifically on the diamond-shape M-TFN with the dimensions of 145µm×20µm and a porosity of 32%. Future studies will require in-vivo testing. Our results demonstrate that M-TFN has a promising potential for carotid artery stenting.

In this review, several cost-effective thin-film coating methods which include dip-coating, spin-coating, spray-coating, blade-coating, and roll-coating are presented. Each method has its set of advantages and disadvantages depending on the type of application. Not all of them are appropriate for large-scale production due to their certain limitations. That is why the coating method should be selected based on the type and size of substrate including the resolution of the required thin-films. The sol-gel method offers several benefits, such as simplicity in fabrication, excellent film uniformity, the capacity to cover surfaces of any size and over vast areas, and a low processing temperature. Nevertheless, these coating methods are somewhat economical and well managed in low-budget laboratories. Moreover, the produced thin-films are homogeneous and have low-surface roughness. Furthermore, some other thin-film deposition methods such as physical vapor deposition (PVD) and chemical vapor deposition (CVD) are also discussed. Since CVD is not restricted to line-of-sight deposition, a characteristic shared by sputtering, evaporation, and other PVD processes, many manufacturing methods favor it. However, these techniques require sophisticated equipment and cleanroom facility. We aim to provide the pros and cons of thin-film coating methods and let the readers decide the suitable technique for their specific application.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

Many advanced technologies have been employed in the high performance active matrix displays including liquid crystal displays, organic light emitting diode displays, and micro light emitting diode displays. On the other side, there have existed the strong demand on the cost reduction and it is one of low cost schemes to integrate the driver circuit in a panel based on thin film transistor technologies. This paper reviews overall concept, operation principles, and various circuit approaches in shift registers for the scanning pulse generation. In addition, it deals with the implementation of additional functionalities in gate drivers to support pixel compensation, multi-line driving, in-cell capacitive touch screen, pixel sensing, and adaptive scanning region control.

In this paper, we study the sensing performance of metasurfaces comprised by spiral-disk-shaped metallic elements patterned on polypropylene substrates, which exhibit localized surface plasmon resonances in the low-frequency region of the THz spectrum (0.2-0.5 THz). Optimal designs of spiral disks with C-shaped resonators placed near the disks were determined and fabricated. The experimentally measured transmittance spectra of samples coated with very thin photoresistive layers (d ~ 10^-4-10^-3 λ) showed good agreement with simulations. The resonance frequency shift Δf increases with increasing d, while saturating near d = 50 µm. The narrow-band magnetic dark modes excited on symmetrical spiral disks with a 90⁰-C-resonator demonstrated very high FOM values reaching 1670 [RIU·mm]^-1 at 0.3μm-thick analyte. The hybrid high order resonances excited on asymmetrical densely packed spiral disks showed about two times larger FOM values (up to 2950 [RIU·mm]^-1) as compared to symmetrical distantly spaced spirals that resembles the best FOM results found in literature for metasurfaces fabricated with a similar technique. The demonstrated high sensing performance of spiral disks is evaluated to be promising for bio-sensing applications in the THz range.

In the present work, doped ZnO (ZnO:Al) thin film has been grown on Silicon (Si) substrate by DC sputtering. The obtained thickness of the film is 230 ± 5 nm. The films were subjected to swift heavy ion (SHI) irradiation 120 MeV, Ag⁹⁺ with different fluences ranging from 3 × 10¹¹ to 3 × 10¹³ ions/cm². To study the impact of SHI, both pristine and irradiated samples were characterized to obtain the structural, surface morphological and electrical properties using X-ray diffractometry (XRD), atomic force microscopy (AFM) and hall effect measurement system respectively. From XRD results it is observed that there is change in crystallinity of the film with increase in irradiation fluence. The surface morphological studies through AFM shows the increase in surface roughness with increase in fluence. A significant change is also observed in electrical parameters viz conductivity, mobility and carrier concentration. Conductivity, mobility and carrier concentration decreases with increasing fluence.

In this work performance improvements are described of a low power consumption non-dispersive infrared (NDIR) methane (CH₄) gas sensor using customised optical thin film bandpass filters (BPF). BPF’s shape the spectral characteristic of the combined mid infrared III-V based light emitting diode (LED)/ photodiode (PD) light source/detector optopair, enhancing NDIR CH₄ sensor performance. The BPF, deposited using a novel microwave plasma assisted pulsed DC sputter deposition process, is deposited at room temperature directly onto the temperature sensitive PD heterostructure. BPF’s comprise germanium (Ge) and niobium pentoxide (Nb₂O₅) alternating high and low refractive index layers respectively. Two different optical filter designs are progressed; with BPF bandwidths (BWs) of 160 nm and 300 nm. Comparison of modelled and measured NDIR sensor performance is described, highlighting maximized signal to noise ratio (SNR) and minimized cross talk performance benefits. BPF spectral stability for various environmental temperature and humidity conditions is demonstrated.

The surface planarity and asperity removal behaviors of atomic scale under the ultrathin water environment was studied for the nanoscale process by molecular dynamics simulation. The monolayer atomic removal was achieved under the noncontact and monoatomic layer contact conditions with different water film thickness, and the newly formed surface is relatively smooth and no deformed layer and plastic defects exist. The nanoscale processing is governed by the interatomic adhering action during which the water film transmits the loading forces to Cu surface and thereby result in the migration and removal of surface atoms. With scratching depth ≥ 0.5 nm, the abrasive particle squeezed out the water film from scratching region and scratched Cu surface directly, leading to the surface quality deterioration mainly governed by the plowing action. This study brings the goals of “0 nm planarity, 0 residual defects and 0 polishing pressure” closer to us in the nanoscale process for the development of ultra-precision manufacture technology.

Bismuth sodium titanate thin films (BNT) were deposited on Pt/SiN substrates by Sol-Gel spin coating technique under O2 atmosphere. Microstructural, structural, and electrical properties of the obtained film were investigated. Scanning electron microscopy and atomic force microscopy micrographs were used to analyze the microstructure of the films. Furthermore, EDX analysis revealed a Na-deficient composition for the obtained film. X-ray diffraction and Raman spectroscopy allowed the identification of a pure perovskite BNT phase. Dielectric, ferroelectric, and leakage current measurements revealed good frequency stability of the dielectric constant and dielectric losses for BNT thin film. The results are discussed in terms of Na-deficiency effects on the defect structure of BNT. Further, the film showed attractive electrostatic energy storage properties with energy density that exceeds 1.04 J/cm3 under E = 630 kV/cm.

The electrical and optical properties of sol-gel derived aluminum-doped0 zinc oxide thin films containing 2 at.% Al were investigated considering the modifying effects of 1) increasing the sol H₂O content; and 2) thermal treatment procedure with high-temperature approach followed by an additional heat-treatment step under a reducing atmosphere. According to the results obtained via the TG-DTA analysis, FT-IR spectroscopy, X-ray diffraction technique and four-point probe resistivity measurement, it is argued that the sol hydrolysis, decomposition of the deposited gel and crystallization of grains result in grains of larger crystallite size and stronger c-axis preferred orientation with slightly less microstrain in the modified sample. The consequent morphology and grain-boundary characteristics turn out as improved conductivity, implying higher values of concentration and mobility of charge carriers. A detailed investigation on samples optical properties, in terms of analyzing their absorption and dispersion behaviors through the UV-Vis-NIR spectroscopy, support our reasoning for the increase of the mobility, and to a lesser extent, the concentration of charge carriers, while causing only a slight degradation of optical transmission. Hence, an enhanced performance as a transparent conducting film is claimed for the modified sample by comparing the figure-of-merit values.

This article presents a new design of supporting tethers through the concept of force distribution. The transmitted force applied on tethers will be distributed on the new tether design area resulting in low acoustic energy transferred to anchor boundaries and stored energy enhancement. This technique achieves an anchor quality factor of 175,000 compared to 58,000 obtained from con-ventional tether design representing 3-fold enhancement. Also, the unloaded quality factor of the proposed design improved from 23,750 to 27,442 representing 1.2-fold improvements.

Thin film transistors (TFTs) using In-Ga-Zn Oxide (IGZO) as active layer and the gate insulator was treated with NH3 plasma and N2O plasma, respectively, which is fabricated on flexible PI substrate in this work. The performance of IGZO TFTs with different plasma species and treatment time are investigated and compared. The experiment results show that the plasma species and treatment time play an important role in the threshold voltage, field-effect mobility, Ion/Ioff ratio, sub-threshold swing (SS) and bias stress stability of the devices. The TFT with a 10 seconds NH3 plasma treatment shows the best performance; specifically, threshold voltage of 0.34 V, field-effect mobility of 15.97 cm2/Vs, Ion/Ioff ratio of 6.33×107, and sub-threshold swing of 0.36 V/dec. The proposed flexible IGZO-TFTs in this paper can be used as driving devices in the next-generation flexible displays.

This paper constituted an extension of two previous studies concerning the mathematical development of the grain boundary grooving in polycrystalline thins films in the cases of the evaporation/condensation and diffusion taken separately. The thermal grooving processes are deeply controlled by the various mass transfer mechanisms of evaporation–condensation, surface diffusion, lattice diffusion, and grain boundary diffusion. This study proposed a new original analytical solution to the mathematical problem governing the grain groove profile in the case of simultaneous effects of evaporation-condensation and diffusion in polycrystalline thin films submitted to thermal and mechanical stress, and fatigue effects; by resolving the corresponding fourth-order partial differential equation ∂y∂t=C∂2y∂x2-B∂4y∂x4 obtained from the approximation y'2≪1. The comparison of the new solution to that of diffusion alone proved an important effect of the coupling of evaporation and diffusion on the geometric characteristics of the groove profile. A second analytical solution based on the series development was also proposed. It was proved that change of the boundary conditions of the grain grooving profile largely affected the different geometric characteristics of the groove profile.

We demonstrate that the conductivity of graphene on thin-film polymer substrates can be accurately determined by reflection-mode air-plasma-based THz time-domain spectroscopy (THz-TDS). The phase uncertainty issue associated with reflection measurements is discussed, and our implementation is validated by convincing agreement with graphene electrical properties extracted from more conventional transmission-mode measurements. Both the reflection and transmission THz-TDS measurements reveal strong nonlinear and instantaneous conductivity depletion across an ultra-broad bandwidth under relatively high incident THz electrical field strengths.

Over the last decades, the coated glass products, and especially the low-emissivity coatings have become a common building material used in modern architectural projects. More recently, these material systems became common in specialized glazing systems featuring solar energy harvesting. Apart from achieving the stability of optical parameters in multilayer coatings, it is also important to have improved control over the design of visual color properties of the coated glass. We prepare metal-dielectric composite (MDC) based multilayer thin-film structures using the RF-magnetron sputtering deposition and report on their optical and chromaticity properties in comparison with these obtained using pure metal-based Dielectric/Metal/Dielectric (DMD) trilayer structures of similar compositions. Experimentally achieved Hunter L, a, b values of MDC-based multilayer building blocks of coatings provide a new outlook on the engineering of future-generation optical coatings with better color consistency and developing approaches to broaden the range of achievable color coordinates and better environmental stability.

Our study aims to implement a strategy to reduce the carbon steel corrosion rate in sulfuric acid solution, using an expired drug with adsorption affinity on the metal surface. To investigate the corrosion protection efficiency of an environmental friendly inhibitor, namely neomycin sulfate (NMS), the electrochemical measurements were applied on carbon steel immersed in 1.0 M H₂SO₄ solution with and without NMS. The protective layer formed on the steel surface was studied by atomic force microscopy (AFM). The potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) showed that the presence of the neomycin sulfate in acid solution leads to the decrease in corrosion current density (i_corr) and the increase of polarization resistance (R_p). The mixed mechanism between physical and chemical adsorption of NMS molecules on the steel surface was proposed according to the Langmuir adsorption isotherm. The Atomic Force Microscopy (AFM) indicated that the NMS molecules contributed to a protective layer formation by their adsorption on the steel surface. The AFM parameters such as: root-mean-square roughness (R_q); average roughness (R_a) and maximum peak to valley height (R_p-v) revealed that in the presence of NMS a smoother surface of carbon steel was obtained, compared to the steel surface corroded in sulfuric acid blank solution.

In this work, zinc oxide (ZnO) thin film has been fabricated on glass substrate using pulse laser ablation (PLA) technique. The effect of laser pulses of 1000, 1500, 2000 pulses at laser energy 700 mJ as well as, laser energy of 600, 700, and 800 mJ at fixed laser pulses of 1500 pulse, with methanol as a solvent on the structural properties of prepared films using XRD, SEM and EDX. XRD results revealed that the ZnO thin films have hexagonal structure with polycrystalline in nature with preferred orientation of (002). Crystalline size was increased with the increasing of the pulses and at energy of 700 mJ and pulse of 1500 pulse seemed nanostructure like tree leaf. In addition, narrow FWHM and no phase change have been observed in all cases. SEM images showed that for all cases the films were homogenous with some island and cluster then cracking started to obtain with the increasing of increase the pulse number. EDX analysis showed that the prepared films were free of defects and contaminations.

An ultraviolet (UV) nanosecond pulsed laser with a wavelength of 355 nm was applied to anneal amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFT) at various laser beam powers ranging from 0 to 280 mW. Laser irradiation was selectively carried out on the a-IGZO channel area using the beam scanning method after the a-IGZO TFT was formed through indium-tin oxide (ITO) electrode patterning and a subsequent lift-off process. After laser annealing, negative shifts in the threshold voltages and enhanced on-currents were observed at laser-beam powers ranging from 54 to 120 mW. No meaningful parameters were investigated for laser beams higher than 200 mW. By extracting the energy band gap and work function of a-IGZO from the transmittance and ultraviolet photoelectron spectroscopy (UPS) results, the ITO electrode/a-IGZO channel energy band structures were established under different laser annealing conditions, and the electron injection mechanism from the ITO to the a-IGZO channel was analyzed and optimized at a laser beam power of 120 mW. The results show that the electrical characteristics of the a-IGZO TFTs can be improved without any heat damage to the substrate because of the selective annealing process.

Using optical characterization, it is evident that the spin state of the spin crossover molecular complex [Fe{H2B(pz)2}2(bipy)] (pz = tris (pyrazol-1-1y)-borohydride, bipy = 2,2’-bipyridine) depends on the ferroelectric polarization of an adjacent thin film of the polymer ferroelectric polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP). The UV-Vis spectroscopy reveals that room temperature switching of [Fe{H2B(pz)2}2(bipy)] molecules in bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] as a function of ferroelectric polar polarization. The electric polarity dependence of bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] shows a strong dependence on the thickness of the PVDF-HFP layer. The PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] interface may affect polarization retention in the PVDF-HFP thin film limit.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

We utilized laser irradiation as a potential technique in tuning the electrical performance of NiOx/SiO2 thin film transistors (TFTs). By optimizing the laser fluence and the number of laser pulses, the TFT performance is evaluated in terms of mobility, threshold voltage, on/off current ratio and subthreshold swing, all of which were derived from the transfer and output characteristics. The 500 laser pulses irradiated NiOx/SiO2 TFT exhibited an enhanced mobility of 3 cm2/V-s from a value of 1.25 cm2/V-s for as-deposited NiOx/SiO2 TFT. The laser-irradiated NiOx material likely has a significant concentration of defect gap states, which could also be involved in light absorption processes. Second, and more importantly, the excess energy that the photogenerated charge carriers possess (due to the significant difference between the photon energy and the bandgap of NiOx), combined with the very high light intensity, would result in complex thermal and photo thermal changes thus resulting in an enhanced electrical performance of p-type NiOx/SiO2 TFT structure.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

An interesting anomaly of the diffusion process with an apparently negative diffusion coefficient defined through the mean-square displacement in a one-dimensional quantum molecular chain model is shown. Nevertheless, the system satisfies the H-theorem, so that the second law of thermodynamics is satisfied. The reason why the “diffusion constant” becomes negative is due to the effect of the phase mixing process, which is a characteristic result of the one-dimensionality of the system. We illustrate the situation where this negative “diffusion constant” appears.

The electrical performance of the back-channel etched Indium–Gallium–Zinc–Oxide (IGZO) thin-film transistors (TFTs) with copper (Cu) source and drain (S/D) which are patterned by a selective etchant was investigated. The Cu S/D were fabricated on molybdenum (Mo) layer to prevent the Cu diffusion to the active layer (IGZO). We deposited the Cu layer using thermal evaporation and performed the selective wet etching of Cu using non-acidic special etchant without damaging the IGZO active layer. We fabricated the IGZO TFTs and compare the performance in terms of linear and saturation region mobility, threshold voltage and ON current (ION). The IGZO TFTs with Mo/Cu S/D exhibits good electrical properties as the linear region mobility is 12.3 cm2/V-s, saturation region mobility is 11 cm2/V-s, threshold voltage is 1.2 V and ION is 3.16 x 10-6 A. We patterned all the layers by photolithography process. Finally, we introduced SiO2-ESL layer to protect the device from the external influence. The results show that the prevention of Cu and introduced ESL layer enhances the electrical properties of IGZO TFTs.

Deep-learning-based convection schemes receive wide attention due to its impressive im-provement on precipitation distribution and tropical convections of earth system simulation. But they cannot represent the stochasticity of moist physics, which will degrade the simulation of large-scale circulations, climate mean, and variability. To solve this problem, a stochastic pa-rameterization scheme based on probabilistic diffusion model named DIFF-MP is developed. The cloud-resolving data from GRIST model is coarse-grained into resolved-scale variables and sub-grid contributions due to moist physics to form the training data. DIFF-MP’s performance is compared against generative adversarial network and variational autoencoder. Results show that DIFF-MP is consistently better than the other two models on prediction error, coverage ratio, and spread-skill correlation. The standard deviation, skewness, and kurtosis of subgrid contributions generated by DIFF-MP is also closer to the testing data than the others. Interpretability experiment shows that DIFF-MP’s parameterization of moist physics is physically reasonable.

We present a new mathematical model of disease spread reflecting specialties of covid-19 epidemic by elevating the role social clustering of population. The model can be used to explain slower approaching herd immunity in Sweden, than it was predicted by a variety of other mathematical models; see graphs Fig. \ref{GROWTH2}. The hierarchic structure of social clusters is mathematically modeled with ultrametric spaces having treelike geometry. To simplify mathematics, we consider homogeneous trees with $p$-branches leaving each vertex. Such trees are endowed with algebraic structure, the $p$-adic number fields. We apply theory of the $p$-adic diffusion equation to describe coronavirus' spread in hierarchically clustered population. This equation has applications to statistical physics and microbiology for modeling {\it dynamics on energy landscapes.} To move from one social cluster (valley) to another, the virus (its carrier) should cross a social barrier between them. The magnitude of a barrier depends on the number of social hierarchy's levels composing this barrier. As the most appropriate for the recent situation in Sweden, we consider {\it linearly increasing barriers.} This structure matches with mild regulations in Sweden. The virus spreads rather easily inside a social cluster (say working collective), but jumps to other clusters are constrained by social barriers. This behavior matches with the covid-19 epidemic, with its cluster spreading structure. Our model differs crucially from the standard mathematical models of spread of disease, such as the SIR-model. We present socio-medical specialties of the covid-19 epidemic supporting our purely diffusional model.

This work reports the role of structure and composition on the determination of the performances of p-type SnOx TFTs deposited by rf magnetron sputtering at room temperature, followed by a post-annealed step up to 200 °C at different oxygen partial pressures (Opp), between 0% and 20%, but where the p-type conduction was only observed between 2.8–3.8%. The role of structure and composition were evaluated by XRD and Mössbauer spectroscopic studies. The study allows to identify the best phases/compositions and thicknesses (around 12 nm) to be used that lead to the production of TFTs with a bottom gate configuration, on glasses coated with conductive Indium Tin Oxide, followed by Aluminium Titanium Oxide dielectric layer with saturation mobility of 4.6 cm²V⁻¹s⁻¹ and on-off ratio above 7 × 10⁴, operating at the enhancement mode with a saturation voltage of −10 V.

This paper presents the automation of the thin-layer chromatography technique whose separation and identification of molecules present in a mixture are currently done manually and laboriously [1]. We have therefore found an interest in automating this technique. In this part, the method implemented comprises 2 steps. First we proceeded to the segmentation of the spots obtained on the chromatographic plate. We then developed a program to identify families of molecules such as coumarins, terpenes, tannins, flavonoids, polyphenols, etc. by calculating segmentation parameters such as standard deviation, entropy, average pixel intensity from an algorithm on the matlab software. Finally our results have been compared to the results obtained by the traditional identification technique in laboratories. Some similarity between the two results obtained shows the reliability and the robustness of our technique.

A number of experiments suggest that the elementary particles are non-local entities. A dissipative self-organization, that treats particles as open systems may provide a better understanding of the underlying phenomena than conservative models. The proposed toy model is such an attempt. We found that self-gravitation (although accompanied by self-diffusion) may not only be compatible with the quantum phenomena but is perhaps the major reason for the existence of quantum fields. According to the proposed model, fields/particles (resemble those of the Standard Model) emerge from a dynamic self-organized medium (which we associate with vacuum dust) from competition between self-gravitation and self-diffusion. These forces produce turbulence in the form of vortices (which we call vacuum cells) that serve as the building blocks for fields and particles. Field/particle features and symmetries are based on their internal (intracellular) dynamics and vortex synchronization (intercellular dynamics). This model allows for rough estimations of relative field coupling strengths, the quantity of charges and flavors, the probabilities of quark transmutations, the dimensionality and the topologies of phase spaces, and other Standard Model parameters that came not from the theory but rather determined by experiment.

Electrospun nanofiber-supported thin film composite membranes are among the most promising membranes for seawater desalination via forward osmosis. In this study, a high-performance electrospun polyvinylidenefluoride (PVDF) nanofiber-supported TFC membrane was successfully fabricated after molecular layer-by-layer polyelectrolyte deposition. Negatively-charged electrospun polyacrylic acid (PAA) nanofibers were deposited on electrospun PVDF nanofibers to form a support layer consisted of PVDF and PAA nanofibers. This resulted to a more hydrophilic support compared to the plain PVDF nanofiber support. The PVDF-PAA nanofiber support then underwent a layer-by-layer deposition of polyethylenimine (PEI) and PAA to form a polyelectrolyte layer on the nanofiber surface prior to interfacial polymerization, which forms the selective polyamide layer of TFC membranes. The resultant PVDF-LbL TFC membrane exhibited enhanced hydrophilicity and porosity, without sacrificing mechanical strength. As a result, it showed high pure water permeability and low structural parameter values of 4.12 Lm⁻²h⁻¹bar⁻¹ and 221 µm, respectively, significantly better compared to commercial FO membrane. Layer-by-layer deposition of polyelectrolyte is therefore a useful and practical modification method for fabrication of high performance nanofiber-supported TFC membrane.

Film therapy, the therapeutic use of movies in psychological therapies, is a growing area of interest to therapists and researchers. This paper presents the MOVIE model of film therapy, a widely applicable, trauma-informed framework for working with film imagery and themes in individual or group therapy, counsellor education and self-help. Film or cinema therapy is a highly accessible and relatable method for many diverse client and student groups with benefits that include, catharsis and emotional processing, greater ease of dialogue around issues, increased empathy, and interpersonal learning, engaging with new perspectives and learning skills. Following the model clients mindfully observe and voice their emotional and psychological responses to movie watching, identify how the imagery, characters, themes, and narrative symbolise personal experience and consider any new possibilities that emerged through re-authoring personal narratives. The model is informed by a practice focused review of literature.

This work is devoted to physical vapor deposition synthesis, and characterisation of bismuth and lutetium-substituted ferrite-garnet thin-film materials for magneto-optic (MO) applications. The properties of garnet thin films sputtered using a target of nominal composition type Bi_0.9Lu_1.85Y_0.25Fe_4.0Ga₁O₁₂ are studied. By measuring the optical transmission spectra at room temperature, the optical constants and the accurate film thicknesses can be evaluated using Swanepoel’s envelope method. The refractive index data are found to be matching very closely to these derived from Cauchy’s dispersion formula for the entire spectral range between 300-2500 nm. The optical absorption coefficient and the extinction coefficient data are studied for both the as-deposited and annealed garnet thin-film samples. A new approach is applied for accurately deriving the optical constants data simultaneously with the physical layer thickness, using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method. MO properties, such as specific Faraday rotation, MO figure of merit and MO swing factor are also investigated for several annealed garnet-phase films.

The concept of this prototype is to create a cold air film layer, in indoor side of the window. The function of this extra cold air layer is to increase the amount of window resistance and decrease its U-Value. It provide air film layer by using the same concept of desert cooler or wind catcher. They both bring the hot air from outside then let it go throw straw miost with cold water. After hot air move through straw, it would become cold, thus increase the window resistance and decrease the haet gian, therefore, decrease the cooling load. So, this window model works by heating the air in air room by sun radiation, then after a while, air pressure will rise and its volume will increase then it will impulse to wet hay, and become cold. Then there is fins to guide air flow to its correct direction, thus inner side of window will become cold, not like other type of window which when temperature rise, the inner side of window become hot. So, this window prevents heat transition and creare regenereted trubouland air flim in the inner side of the window. Using calculation to find air film characteristics and WINDOW7.7 software to calculate heat gain through window, shows that it is expected from this prototype to reduce heat gain by 6.85 % for double glazed clear window.

Diffusion magnetic resonance imaging (dMRI) is an imaging technique that provides information on the microstructural organization of biological tissue. dMRI allows for non-invasive visualization and quantitative assessment of white matter architecture in the brain by characterizing restrictions on the random motion of water molecules. Ultra-high field MRI scanners, such as those operating at 7 Tesla (7T) or higher, can boost signal-to-noise ratio (SNR) to improve dMRI compared with what is attainable at conventional field strengths such as 3T or 1.5T. However, at 7T wavelength effects cause lower transmit magnetic field efficiency in the human brain, mainly in the posterior fossa region, manifesting as signal dropouts in this region. Recently, we reported a simple approach of using a wireless radiofrequency (RF) surface array to improve transmit efficiency and signal sensitivity at 7T. Here we demonstrate the feasibility and effectiveness of using this RF enhancer for in-vivo dMRI at 7T. The use of the RF enhancer can effectively recover signal dropouts in the regions with intrinsically lower SNR such as cerebellum, leading to a better depiction of principal fiber orientations and enhanced visualization of extended tracts to the brainstem and pons enabling more comprehensive delineation of the full white matter architecture.

In permafrost regions, ground surface deformations induced by freezing and thawing threaten the integrity of the built environment. Mapping the frost susceptibility of the ground at a high spatial resolution is of practical importance for the construction and planning sectors. We processed Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) data from thawing seasons 2015 to 2019, acquired over the area of Ilulissat, West Greenland. We used a least-squares inversion scheme to retrieve the average seasonal displacement (S) and long-term deformation rate (R). We secondly investigated two different methods to extrapolate active layer thickness (ALT) measurements, based on their statistical relationship with remotely-sensed surface characteristics. A Generalized Linear Model (GLM) was first implemented, but the model was not able to fit the data and represent the ALT spatial variability over the entire study domain. ALT were alternatively averaged per vegetation class, using a land cover map derived by supervised classification of Sentinel-2 images. We finally estimated the active layer ice content and used it as a proxy to map the frost susceptibility of the ground at the community scale. Fine-grained sedimentary basins in Ilulissat were typically frost susceptible and subject to average seasonal downward displacements of 3 to 8 cm. Areas following a subsiding trend of up to 2.6 cm/yr were likely affected by permafrost degradation and melting of ground ice below the permafrost table. Our approach enabled us to identify frost-susceptible areas subject to severe seasonal deformations, and/or long-term subsidence induced by degrading permafrost. Used in combination with traditional site investigations, InSAR maps provide valuable information for risk management and community planning in the Arctic.

The work is devoted to the investigation of virus quasispecies evolution and diversification due to mutations, competition for host cells, and cross-reactive immune responses. The model consists of a nonlocal reaction-diffusion equation for the virus density depending on the genotype considered as a continuous variable and on time. This equation contains two integral terms corresponding to the nonlocal effects of virus interaction with host cells and with immune cells. In the model, a virus strain is represented by a localized solution concentrated around some given genotype. Emergence of new strains corresponds to a periodic wave propagating in the space of genotypes. The conditions of appearance of such waves and their dynamics are described.

In this paper, we consider the Cauchy problem of a time fractional nonlinear diffusion equation. According to the Kaplan’s first eigenvalue method, we first prove the blow-up of the solutions in finite time for some sufficient conditions. We next give sufficient conditions for the existence of global solutions by using the result of Zhang and Sun. In conclusions, we find the second critical exponent for the existence of global and non-global solutions via the decay rates of the initial data at spatial infinity.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

We propose a deep learning algorithm that directly compensates for luminance degradation owing to the deterioration of organic light emitting diode (OLED) devices to address the burn-in phenomenon of OLED displays. Conventional compensation circuits are encumbered by a high cost of development and manufacturing processes owing to their complexity. However, given that deep learning algorithms are typically mounted on a system on chip (SoC), the complexity of the circuit design is reduced, and the circuit can be reused by re-learning only the changed characteristics of the new pixel device. The proposed approach comprises deep feature generation and multi-stream self-attention, which decipher the importance of the variables, and the correlation between burn-in-related variables. It also utilizes a deep neural network that identifies the nonlinear relationship between the extracted features and luminance degradation. Thereafter, the luminance degradation is estimated from the burn-in-related variables, and the burn-in phenomenon can be addressed by compensating for the luminance degradation. The experimental results revealed that compensation was successfully achieved within an error range of 4.56%, and demonstrate the potential of a new approach that can mitigate the burn-in phenomenon by directly compensating for pixel-level luminance deviation.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Link prediction is a fundamental problem in graphs. Currently, SubGraph Representation Learning (SGRL) methods provide state-of-the-art solutions for link prediction by transforming the task into a graph classification problem. However, existing SGRL solutions suffer from high computational costs and lack scalability. In this paper, we propose a novel SGRL framework called Augmented Feature Diffusion on Sparsely Sampled Subgraph (AFD3S). The AFD3S first uses a conditional variational autoencoder to augment the local features of the input graph, effectively improving the expressive ability of downstream Graph Neural Networks. Then, based on a random walk strategy, sparsely sampled subgraphs are obtained from the target node pairs, reducing computational and storage overhead. Graph diffusion is then performed on the sampled subgraph to achieve specific weighting. Finally, the diffusion matrix of the subgraph and its augmented feature matrix are used for feature diffusion to obtain operator-level node representations as inputs for the SGRL-based link prediction. Feature diffusion effectively simulates the message-passing process, simplifying subgraph representation learning, thus accelerating the training and inference speed of subgraph learning. Our proposed AFD3S achieves optimal prediction performance on several benchmark datasets, with significantly reduced storage and computational costs.

In a previous paper, we solved the partial differential equation of Mullins problem in the case of the evaporation-condensation in electronic devices and gave an exact solution relative to the geometric profile of the grain boundary grooving when materials are submitted to thermal and mechanical solicitation and fatigue effect. In this new research, new modelling of the grain groove profile was proposed and new analytical expressions of the groove profile, the derivative and the groove depth were obtained in the case of diffusion in thin polycrystalline films by the resolution of the fourth differential equation formulated by Mullins that supposed 〖y'〗^2≪1. The obtained analytical solution gave more accurate information on the geometric characteristics of the groove that were necessary to study the depth and the width of the groove. These new findings will open a new way to study with more accuracy the problem of the evaporation-condensation combined to the diffusion phenomenon on the material surfaces with the help of the analytical solutions.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Electrostatic endothelial cell seeding has evolved as an exceptional technique to improve the efficiency of cell seeding in terms of frequency of attached cells and the amount of cell adhesion for the treatment of vascular diseases. In the recent times, both untreated and superhydrophilic thin film nitinol (TFN) have exhibited strong prospect as substrates for creation of small-diameter endovascular grafts due to their hallmark properties of superelasticity, ultra low-profile character, grown hemocompatible oxide layer with the presence of a uniform endothelial layer on the surface. The purpose of the current study is to understand the effects of endothelial cell seeding parameters (i.e., applied voltage, incubation time, substrate chemistry and cell suspension solution) to investigate the cell seeding phenomenon and to improve the cell adhesion and growth on the TFN surface under electrostatic transplantation. Both parallel plate and cylindrical capacitor models were used along with the Taguchi Design of Experiment (DOE) methods to design in vitro test parameters. A novel in vitro system for cylindrical capacitor model was created using a micro flow pump, micro incubation system, and silicone tubings. The augmented endothelialization on thin film nitinol was developed to determine the effect of cell seeding and deployed in a 6 Fr intravascular catheter setup. Cell viability along with morphology and proliferation of adhered cells were evaluated using fluorescent and scanning electron microscopy. Our results demonstrated that the maximum number of cells attached on STFN in the catheter was observed in 5V with the 2 hr exposure of in the cell culture medium (CCM) solution. The condition showed 5V voltage with 0.68×10-6 µC electrostatic charge and 5.11 V·mm-1 electric field. Our findings have first demonstrated that the electrostatic endothelialization on the superhydrophilic thin film nitinol endograft within the catheter prior to the endovascular procedure could enhance the biocompatibility for low-profile endovascular applications.

Painting style and creativity are fundamental to art, defining a work’s uniqueness and expression. They embody an artist’s personality, convey emotions, establish identity, and shape audience perception, adding depth and value to the work. Recently, diffusion models have gained popularity in art design, animation, and gaming, especially in original painting creation, poster design, and visual identity development. Traditional creative processes, while demanding unique imagination and creativity, often face challenges such as slow innovation, high reliance on manual efforts, high costs, and limitations in scalability. Consequently, exploring painting-style creative design through deep learning has emerged as a promising trend. In this paper, we introduce a novel network architecture, the Painting-Style Design Assistant Network (PDANet), for style transformation. To support this, we curated the Painting-42 dataset, comprising 4,055 works by 42 renowned Chinese painters. PDANet leverages this dataset to capture the aesthetic intricacies of Chinese painting, offering rich design references. Furthermore, we propose a lightweight Identity-Net for large-scale text-to-image (T2I) models, which aligns internal knowledge with external control signals, thereby enhancing the capabilities of existing T2I models. The trainable Identity-Net feeds image prompts into the U-Net encoder to generate diverse and stable images. Both quantitative and qualitative analyses demonstrate that our approach outperforms current methods, delivering high-quality generated content with wide-ranging applicability.

COVID-19 infection, caused by SARS-CoV-2, is inequitably distributed and more lethal among populations with lower socioeconomic status. Direct contact with contaminated surfaces has been one of the virus sources, as it remains infective up to days. Several disinfectants have been shown to inactivate SARS-CoV-2 but they rapidly evaporate, are flammable or toxic and may be scarce or inexistent for the vulnerable populations. Therefore, we are proposing a simple, easy to prepare, low-cost and efficient antiviral films, made with wide available dishwasher detergent, which can be spread in hands and inanimate surfaces and maintains virucidal activity for longer periods than the current sanitizers. Avian coronavirus (ACoV) was used as model of challenge to test the antivirus efficacy of proposed films. Polystyrene microplates were covered with a thin layer of detergent formula. After drying, the films were exposed to different virus doses for 10 minutes and virus infectivity were determined using embryonated chicken eggs and RNA virus quantification in allantoic fluids by RT-qPCR. The films showed to inactive the ACoV (ranging from 103.66 to 106.66 EID50), which is chemically and morphologically similar to SARSCoV-2 and may constitute an excellent alternative to minimize the spread of Covid-19.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

In this paper, we investigate the following chemotaxis-haptotaxis model $$\left\{ \begin{array}{ll} u_{t}=\nabla\cdot (D(u) \nabla u)- \nabla\cdot (H(u)\nabla v)- \nabla\cdot (I(u)\nabla w)+ u(a-\mu u^{k-1}-\lambda w),\\ v_{t}=\triangle v-v+u^{\gamma},\\ w_{t}=-v w \end{array}\right.\eqno(*) $$ under homogenous Neumann boundary condition and for a bounded domain $ \Omega \subset \mathbb{R}^{n} (n\geq2)$, with $\lambda, \mu, \gamma >0$, $k>1$, $a \in \mathbb{R}$, and $D(u)\geq K_{D} (u+1)^{m-1}$, $0\leq H(u)\leq \chi u(u+1)^{-\alpha}$, $0\leq I(u)\leq \xi u(u+1)^{-\beta}$ for $K_{D}, \chi, \xi>0, m, \alpha, \beta\in \mathbb{R}$. It has been demonstrated that (i) For $0\gamma-k+1$ and $\beta>1-k$, problem ($*$) admits a classical solution $(u, v, w)$ which is globally bounded. (ii) For $\frac{2}{n}\gamma-k+\frac{1}{e}+1$ and $\beta>\max\{\frac{(n\gamma-2)(n\gamma+2k-2)}{2n}-k+1, \frac{(n\gamma-2)(\gamma+\frac{1}{e})}{n}-k+1\}$ or $\alpha>\gamma-k+1$ and $\beta>\max\{\frac{(n\gamma-2)(n\gamma+2k-2)}{2n}-k+1, \frac{(n\gamma-2)(\alpha+k-1)}{n}-k+1\}$, problem ($*$) admits a classical solution $(u, v, w)$ which is globally bounded.

The purpose of this paper is to study the influence of diffusion and thermal loading due to pulsed laser heating on a thermoelastic solid with voids in the context of the model of three-phase-lag. The non-dimensional governing equations are formulated and then the exact expressions for the temperature field, the displacement components, the stress components, the concentration field and the change in the volume fraction field are obtained using the normal mode technique. The material is an isotropic, homogeneous elastic half-space and heated by a non-Gaussian laser beam with pulse duration of ps. The magnesium crystal element is used as an application to compare the predictions induced by diffusion and laser pulse on poro-thermoelastic medium of the model of three-phase-lag with those for the theory of Green–Naghdi of type III. The results obtained for thermal changes are verified by comparison with two theories of thermoelasticity, namely the model of three-phase lag (3PHL) and the Green and Nagdi type III theory. Plot the expressions to examine the effect of the laser pulse at two different values of time and the effect void parameter. This study also yields some interesting special cases.

We demonstrate high quality (intrinsic Q factor ~2.8×106) racetrack microresonators fabricated on lithium niobate (LN) thin film with a free spectral range (FSR) of ~86.38 pm. By integrating microelectrodes alongside the two straight arms of the racetrack resonator, the resonance wavelength around the 1550 nm can be red shifted by 92 pm when the electric voltage is raised from -100 V to 100 V. The microresonators of the tuning range spanning over a full FSR is fabricated using photolithography assisted chemo-mechanical etching (photolithography assisted chemo-mechanical etching, PLACE).

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

The research that we are referring to examines the morphological, structural, and optical characteristics of kesterite (Cu1-xAgx)2ZnSnS4 (CAZTS) thin films, which are produced using a process known as thermal evaporation (TE). The study's main goal was to determine how different Ag contents affect the characteristics of CAZTS systems. X-ray diffraction (XRD) and Raman Spectroscopy: were used to confirm the crystal structure of the CAZTS thin films. Using a mathematical model of spectroscopic ellipsometry, the refractive index (n) represented the part of the complex refractive index, the extinction coefficient (k) portrayed the imaginary one, and also the energy band gap of the fabricated films were all calculated. The energy band gap of the thin films was also calculated. This is a crucial parameter for solar cell applications, as it determines the wavelength of light that the material can absorb. The energy band gap was found to decrease from 1.74 eV to 1.55 eV with increasing Ag content. The ITO/n-CdS/p-CAZTS/Mo heterojunction was well constructed, and the primary photovoltaic characteristics of the n-CdS/p-CAZTS junctions were examined for use in solar cells. Different Ag contents of the CAZTS layers were used to determine the dark and illumination (current-voltage) characteristics of the heterojunctions. The study's findings collectively point to CAZTS thin layers as potential absorber materials for solar cell applications.

We investigate the influence of a self-propelling, out-of-equilibrium active particle on generalized elastic systems, including flexible and semiflexible polymers, fluid membranes, and fluctuating interfaces, while accounting for long-ranged hydrodynamic effects. We derive the fractional Langevin equation governing the dynamics of the active particle, as well as that of any other passive particle (or probe) bound to the elastic system. Our study explores the diffusional behavior emerging for both the active particle and a distant probe.

In recent years, electrochemical methods utilizing reactive electrochemical membranes (REM) have been recognized as the most promising technologies for the removal of organic pollutants from water. In this paper, we propose a 1D convection-diffusion-reaction model concerning the transport and oxidation of oxalic acid (OA) and oxygen evolution in the flow-through electrochemical oxidation system with REM. It allows the determination of unknown parameters of the system by treatment of experimental data and predicts the behavior of the electrolysis setup. There is a good agreement in calculated and experimental data at different transmembrane pressures and initial concentrations of OA. The model provides an understanding of the processes occurring in the system and gives the concentration, current density, potential and overpotential distributions in REM. The dispersion coefficient was determined as a fitting parameter and it is in good agreement with literary data for similar REMs. It is shown, that the oxygen evolution reaction plays an important role in the process even under the kinetic limit, and its contribution decreases with increasing total organic carbon flux through the REM.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

Walls-like structured monoclinic WO3 thin films were obtained by spray deposition method for further integration in gas sensors. For sensing applications, it is very important to achieve a high surface-to-volume ratio surface together with a proper thin films structure. The present communication reports on the effect of the sprayed solution volume variation (as a thickness variation element) on the detailed Raman spectroscopy for WO3 thin films with different thicknesses grown from precursor solutions with two different concentrations. Detailed analysis of the two series of samples shows that the growing thickness strongly affects the films morphology while their crystalline structure is only slightly affected. The Raman analysis contribute to refining the structural features clarifications. It was observed that, for both concentrations, the increase in thickness seems to slightly affect the stoichiometry of material and, in association with surface morphology variations, provide new possibilities for fine tuning of films properties towards enhanced as sensing applications. Further studies are ongoing.

Optical rotatory dispersion (ORD) is a beautiful analytical technique for the study of chiral molecules and polymers. In this study, ORD was applied successfully to follow the degree of polycondensation of l-(+)-lactic acid toward the formation of poly(lactic acid) oligomers (PLAO) and high molecular weight poly(l-lactic acid) (PLLA) in a simple esterification reaction equipment. PLLA is a biodegradable polymer obtainable from renewable raw materials. The racemization of the intrinsically isotactic PLLA through thermal treatment can be easily followed through the use of ORD spectroscopy. Organic or molecular electronics is a hot topic dealing with the combination of π-conjugated organic compounds and polymers with specific properties (e.g. chirality) which can be exploited to construct optoelectronic devices such as organic light-emitting diodes (OLEDs), organic photovoltaic (OPV) high efficiency cells, switchable chirality devices, organic field-effect transistors (OFETs), and so on. ORD spectroscopy was applied to study either the gigantic optical rotation of PLLA films as well as to detect successfully the excitonic coupling occurring in thin solid PLLA green film loaded with a combination of two dyes: SY96 (a pyrazolone dye) and PB16 (the metal-free phthalocyanine pigment). The latter compound PLLA loaded with SY96 and PB16 shows a really gigantic optical activity in addition to typical ORD signal due to exciton coupling and may be considered as a simple and easily accessible model composite of a chiral polymer matrix combined with π-conjugated dyes for molecular electronics studies.

In this paper, the author utilizes Saddle Theorem and variational methods to deduce existence of at least six stationary solutions for reaction-diffusion Gilpin-Ayala competition model (RDGACM). To obtain the global stabilization of the positive stationary solution of the RDGACM, the author designs a suitable impulsive event triggered mechanism (IETM) to derive the global exponential stability of the the positive stationary solution. It is worth mentioning that the new mechanism can exclude Zeno behavior and effectively reduce the cost of impulse control through event triggering mechanism. Besides, compared with existing literature, the restrictions on the parameters of the RDGACM are relaxed so that the methods used in existing literature can not be applied to the relaxed case of this paper, and so the author makes comprehensive use of Saddle Theorem, orthogonal decomposition of Sobolev space $H_0^1(\Omega)$ and variational methods to overcome the mathematical difficulty. Numerical examples show the effectiveness of the methods proposed in this paper.

Steel surface protection with hard coatings is essential in the metalworking industry, yet developing high-performance hard coatings still remains a challenge. Quaternary nitride coatings, particularly TiAlSiN, have been extensively studied, but commercial TiAlSiN coatings vary widely, and there is a lack of consistent data. This study presents findings on the development and evaluation of TiAlSiN and TiAlSiN/TiN thin films, with an 800 nm thick TiAlSiN top coating and a 100 nm thick TiN mid-coating. The films were deposited on C120 tool steel discs via reactive DC magnetron sputtering. Ti and TiAlSi 75–20–5 (at.%) disc-shaped targets (50.8 mm diameter × 6.3 mm thickness), fabricated by our team through spark plasma sintering, were used for the sputtering process. Coatings were grown on smooth steel substrates heated to 300 °C, resulting in a uniform micro-structure with nanoparticles of globular (TiN) or pyramidal shape (TiAlSiN), as evidenced by SEM analysis. Nanoindentation tests showed superior mechanical properties for all coatings compared to the steel substrate. Micro-scratch tests indicated better scratch resistance for TiAlSiN/TiN bilayer (BL) coatings than for TiAlSiN single-layer (SL) coatings. Electrochemical impedance spectroscopy tests in a 3.5 wt.% NaCl solution revealed that the BL coatings demonstrated superior corrosion resistance compared to the SL coatings, even after thermal aging at 800 °C for 1 hour. The superior properties of the synthesized TiAlSiN/TiN films recommend them as protective coatings for tool steel surfaces.

Seedling emergence is crucial for the establishment and growth of crops and is influenced by topsoil temperature and moisture. Mulching has been widely used to promote seedling emergence in areas with a cold spring. This study was conducted to determine and simulate the effects of transparent plastic film mulch on surface soil moisture, temperature, and seedling emergence of spring maize in Northwest China. Four treatments were used: no mulching (CK), full plastic film mulch (PMF), and partial plastic film mulch, 60 cm in width (PM60, 40 cm uncovered between rows of mulch) or 30 cm in width (PM30, 20 cm uncovered between rows of mulch). The effects of soil water conservation and temperature enhancement gradually decreased as the plastic film width decreased, but there was little difference between PMF and PM60 treatments. Soil-water-modified growing degree days (WGDD) described the beneficial effects of soil moisture and temperature with respect to seedling emergence under mulching conditions. Plastic film mulching markedly accelerated seedling emergence and increased final seedling emergence rate because mulching can shorten the autotrophy duration and maintain surface soil moisture, which leads to increased germination. The effects of seedling emergence improvement decreased as the plastic film width decreased. The relationship between WGDD and cumulative relative seedling emergence (CRE) was adequately described by a Gompertz function.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

In this paper, we investigate a financial market in which asset prices evolve based on a multi-dimensional Brownian motion process and a multi-dimensional Poisson process with different credit and deposit rates We proceed to evaluate European options by establishing upper and lower hedging prices through a transition to a suitable auxiliary market. Additionally, we address the minimization of shortfall risk and no-arbitrage price bounds in incomplete markets within this framework.

We consider a control problem for a diffusive PDE model of heterogeneous population of thermostatically controlled loads (TCLs) aiming to balance the aggregate power consumption within a given amount of time. Using the Green’s function approach, the problem is formulated as an approximate controllability problem for a residue depending on control parameters nonlinearly. A sufficient condition for approximate controllability is derived in terms of initial temperature distribution, operation time of TCLs and threshold value of the aggregate power consumption. Case studies allow to reveal the advantages of the proposed solution from numerical calculations point of view.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

A simple in vitro biosensor for the detection of β-amyloid 42 in phosphate-buffer saline (PBS) and undiluted human serum was fabricated and tested based on our platform sensor technology. The bio-recognition mechanism of this biosensor was based on the effect of the interaction between antibody and antigen of β-amyloid 42 to the redox couple probe of K₄Fe (CN) ₆ and K₃Fe (CN) ₆. Differential pulse voltammetry (DPV) served as the transduction mechanism measuring the current output derived from the redox coupling reaction. The biosensor was a three-electrode electrochemical system, and the working and counter electrodes were 50 nm thin gold film deposited by sputtering technique. The reference electrode was a thick-film printed Ag/AgCl electrode. Laser ablation technique was used to define the size and structure of the biosensor. Cost-effective roll-to-roll manufacturing process was employed in the fabrication of the biosensor making it simple and relatively inexpensive. Self-assembled monolayers (SAM) of 3-Mercaptopropionic acid (MPA) was employed to covalently immobilize the thiol group on the gold working electrode. A carbodiimide conjugation approach using N-(3-dimethylaminopropyl)-N’-ethylcarbodiimide hydrochloride (EDC) and N–hydroxysuccinimide (NHS) was undertaken for cross-linking antibody of β-amyloid 42 to the carboxylic groups on one end of the MPA. The antibody concentration of β-amyloid 42 used was 18.75µg/mL. The concentration range of β-amyloid 42 in this study was from 0.0675µg/mL to 0.5µg/mL for both PBS and undiluted human serum. DPV measurements showed excellent response in this antigen concentration range. Interference study of this biosensor was carried out in the presence of Tau protein antigen. Excellent specificity of this β-amyloid 42 biosensor was demonstrated without interference by other species such as T-tau protein.

This article aims to carry out experiments on water absorption by husked red rice, at constant temperatures of 28, 40 and 50 °C. The description of the absorption kinetics, as well as the analyses of water distribution and volumetric expansion of each grain, at a given instant, was done using a diffusion model. In order for the model to be as close as possible to the real physical situation, the mesh necessary to numerically solve the diffusion equation was generated from the photograph of a grain. Thus, the diffusion equation was written in Boundary-Fitted Coordinates (BFC). The solution of the diffusion equation written in generalized coordinates was then discretized in space and time, using the Finite Volume method, with a fully implicit formulation, considering variable volume and also variable mass diffusivity as a function of local moisture content. Optimizations based on Levenberg-Marquardt algorithm make it possible to determine the parameters of an exponential function relating mass diffusivity and the local moisture content for each temperature. Statistical indicators (chi-square, determination coefficient and Student’s t-test) allowed concluding that the model proposed was very satisfactory for all temperatures, making it possible to simulate water absorption, water distribution and volumetric expansion of the grain over time.

The application of OpenAI's advanced artificial intelligence language model, ChatGPT, in education has garnered widespread attention from the academic community. The openness and intelligence features of ChatGPT demonstrate great potential and value in supporting students' learning, daily life, and communication. This study, grounded in the theoretical frameworks of Innovation Diffusion Theory (IDT) and the Technology Acceptance Model (TAM), conducted a systematic empirical analysis through a questionnaire survey of 677 university students who had used or were currently using ChatGPT. The results indicate that the six perceived attributes of innovation significantly influence university students' behavioral intention to use ChatGPT, while attitudes towards ChatGPT, perceived usefulness, and perceived ease of use indirectly influence students' behavioral intention to continue using ChatGPT. Based on the findings of this study, we propose an extended Technology Acceptance Model (TAM) that incorporates key elements of Innovation Diffusion Theory (IDT) to optimize the application of advanced technologies, such as ChatGPT, in education, thereby improving students' learning efficiency and behavioral performance. These findings not only provide important insights into the complex relationships between college students’ perceptions of ChatdGPT technology and predictors of behavioral intentions, but can also help relevant education departments, higher education institutions, and university teachers to effectively plan and evaluate the use of ChatGPT as a learning tool.