The introduction provides an overview of beginning the development of a plastic design of metal thin-walled cross-sections. This large study investigates in detail together 14 steel and four extruded aluminium cross-sections. Six groups of various shaped cross-sections that consist of: four I-shaped doubly symmetric sections (two I-sections, one I-section with lips, one H-section); three monosymmetric sections with axis of symmetry z (monosymmetric I-section, T-section, diamond section); four monosymmetric sections with axis of symmetry y (two channels, channel with inside lips, channel with outside lips); two point symmetric sections (Z-section with and without lips); four asymmetric sections (L-profile, sigma section, two closed sections: oblique and irregular sections; non-warping sections along midline, but with negligible warping along the element's thicknesses: Tsection and L-profile are included in the above groups. Four extruded aluminium cross-sections are: I 200a section, diamond section and closed oblique and irregular sections. For all 18 cross-sections, the plastic section moduli of three kinds were calculated: Wpl,y,nB, Wpl,z,nB for bimoment not considered to be constraint; Wpl,y, Wpl,z, Wpl,wfor bimoment considered to be restraint; maximum values Wpl,y,max, Wpl,z,max, Wpl,w,max. The values of cross-section plastic resistances Npl, Mpl,y,Rd, Mpl,z,Rd and Bpl are also calculated in numerical examples. The values of cross-section properties are calculated in different ways to verify the correctness of the results. The following ways of calculations are used: the rules in Eurocode EN 1993-1-1: 2022; own MathCad programmes; own software. Recommendations for educational institutes and designers in practice are provided, including simple formulae for all the cross-sectional properties for the doubly and monosymmetric I-shaped sections, channels and Z-sections. Formulae are presented in six tables containing formulae in the dimensionless form, which are useful for parametrical studies and formulae for direct designs. The background of the Eurocode rules in EN 1993-1-1: 2022 is explained together with recommendations about how to avoid problems with using them.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Snap-fit is a commonly used jointing/connention mechanism, and its easy installation and difficult removal are the result of the coordinated interaction between friction, geometric shape, and elasticity. This paper presents a detailed study on the assembly/disassembly forces of thin-walled torus snap-fit through finite element simulation, experimental testing, and data fitting of approximate analytical solutions. The research reveals that the non-zero Gaussian curvature of the torus has a significant impact on the mechanical performance of the torus snap fit. The findings in this study are of great significance for future design of high-performance structural connections.

Two-dimensional arrays of hollow nanotubes made of TiO2 are a promising platform for sensing, spectroscopy and light harvesting applications. Their straightforward fabrication via electrochemical anodization, growing nanotube pillars of finite length from a Ti foil, allows precise tailoring of geometry and, thus, material properties. We investigate these photonic crystal structures with respect to reduction of front surface reflection, achievable field enhancement, and photonic bands. With the Rigorous Coupled Wave Analysis (RCWA), we study the optical response of photonic crystals made of thin-walled nanotubes relative to the bare Ti foil substrate, including under additional charge carrier doping.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Defensive structure is important in transportation field for kinds of intentional or unintentional explosion. Structures subjected to unconfined and confined explosion will bear different blast loads and their dynamic responses are different. The present work focus on the dynamic response mechanism of steel plate under unconfined and confined blast loads through both numerical and experimental studies. In the experiment, Digital Image Correlation (DIC) technique was applied to record and analyze the dynamic response process of large-scale field blast test. The DIC measured curve and the numerical calculated curves agrees well in both the trends and the peak values. Then, the dynamic response mechanism of steel plate under unconfined blast (UB) load and confined blast (CB) load were compared and discussed. Results show that the dynamic response of plate can be divided into three phases under both UB and CB loads, while with different mechanism. In phase I, plastic hinge starts from the center and moves to the boundary in UB condition, while in case of CB, plastic hinge occurs close to the boundary and moves in the opposite direction. In phase II, two plastic hinge lines propagates towards each other, and a platform exists between the boundary and the central area remains undeformed in UB condition, while in CB condition, larger deformation in peripheral region rather than central area produces.

In the presented work, on the example of thin-walled specimens made by selective laser melting technology from AlSi10Mg subjected to preliminary heat treatment, it is shown that there is a critical point of transition from the elastic-plastic region of the engineering stress-strain diagram to the yield and fracture stresses. It was found that the critical point has a strong statistically significant correlation (0.83 by Spearman and 0.93 by Pearson) with the strain hardening coeffi-cient calculated in the section from yield strength to fracture strength. A regression equation linking the critical transition point to the strain hardening coefficient was obtained. It is shown that with increasing plasticity of thin-walled samples obtained by selective laser melting of AlSi10Mg leads to a change in the type of stress distribution in the elastic-plastic region (the Weibull distribution changes to a normal distribution) and the contribution of the probability density of stress distribution described by the Cauchy distribution with a mode near the fracture stress to the full probability density of fracture increases.

This research investigates the effects of torsional moments on the mechanical behavior of thin-walled open-ended vertical pile foundations subjected to lateral wind loads. The warping and torsion effect generated over the piles due to the resultant lateral load impact outside the shear center is analyzed in-field tests. Complementarily, a two-dimensional finite element model based on the simple bending stress-strain state as well as a three-dimensional finite element model considering torsional effects were implemented and their results analyzed. Finally, a comparative analysis between the in-field lateral loading tests and the finite element model approaches was established and correlations between the errors and the parameters of influence were highlighted. From the results, it has been ascertained that the slender thin-walled open-ended pile foundations are particularly sensitive to small load deviations from their center of gravity, this leads to the fact that the slenderer and the more eccentricity of the load, the more it affects the torsion and warping of the pile. Calculation methodologies usually consider a simple in-plane bending behavior which conducts to errors between 44 and 58% of the experimental results.

Continuous rigid frame bridges across valleys are often at the risk of rockfalls caused by heavy rainfalls, earthquakes and debris flows in a mountainous country. Hollow thin-walled bridge piers (HTWBP) in valleys are exposed to the threat of the impact of accidental rockfalls. In the current research, ANSYS/LS-DYNA is used to establish a high-precision rockfall-HTWBP model. The rockfall-HTWBP model is verified against a scaled impact test of a previous research. A mesh independence test is also performed to obtained an appropriate mesh size. Based on the rockfall-HTWBP model, the impact force, damage and dynamic response characteristics of HTWBP under the rockfall impact are studied. In addition, a damage assessment criteria is proposed based on the response surface model combined with Central Composite Design method and Box-Behnken Design method. The main conclusions are as follows: 1）The impact force of rockfall has a substantial impulse characteristic, and the duration of the impulse load is approximately 0.01s. 2）The impacted surface of the pier is dominated by the final elliptic damage with the conical and strip damage areas as the symmetry axis. The cross-sectional damage mode is compression failure in the impact area and shear failure at the corner. 3）The maximum displacement occurs in the middle height of the pier. The maximum displacement increases with impact height, impact velocity and rockfall diameter and decreases with the uniaxial compressive strength of the concrete. 4) The initial impact velocity and diameter of the rockfall are the most significant parameters affecting the damage indices. In addition, a damage assessment method with a damage zoning diagram based on the response surface method is established for the fast assessment of the damage level of impacted HTWBP.

The paper is aimed to develop an improved acoustic-based Structural Health Monitoring (SHM) and Non-Destructive Evaluation (NDE) techniques, which provide the waves directivity emitting by the angle-beam wedge actuators in the thin-walled structures made of plastic materials and polymeric composites. Our investigation includes the dispersive analysis of the waves that can be excited in the studied plastic panel. Its results allowed to find two kinds of the generated acoustic waves - anti-symmetric Lamb waves A0 and shear horizontally polarized SH waves SS0. The bounds of the chosen frequency range for the experimental and numerical studies were accepted as a compromise between the desire to obtain high defects resolution by generating short waves, their adjustable directivity and maximum propagation length. The finite element model for the transducer was built by using the results of actuator structure experimental study. The frequency response functions for the actuator current and oscillation amplitude of the footprint surface demonstrated good agreement. The found eigenfrequencies of actuator's structure were used for the numerical and experimental study of the Lamb and SH wave generation and propagation in a thin-walled plastic panel. Our results convincingly demonstrated the satisfactory directivity of the actuated waves at their excitation on the frequencies that corresponded to the natural modes of the actuator oscillation. The authors assume that an efficient use of the proposed technique for other analyzed quasi-isotropic materials and applied actuators can be provided by a preliminary research using the similar approach and methods presented in this article.

Experimental tests and numerical analyses were carried out on short, thin-walled channel columns with modified cross-sectional shape. The columns were loaded with an axial compressive force applied at the center of gravity of the cross section. Tests were carried out on a universal testing machine, while numerical analyses were performed in ANSYS software. The purpose of the tests was to determine the values of critical forces for the compressed columns and to determine the values of maximum forces at which failure of the columns occurs. Critical forces were determined based on the strain-averaged method. Based on the study, it was found that the strength and resistance to loss of stability of columns is primarily affected by their stiffness, and therefore by the shape of the cross-sections. In addition, for short columns, it seems more important to determine the value of maximum forces than the values of critical forces.

Photocatalytic ammonia decomposition to produce N2 and H2 was achieved using single-walled carbon nanotube (SWCNT) nanohybrids. Physical modification of ferrocene-dye-encapsulated CNTs by amphiphilic C60-dendron yielded nanohybrids with a dye/CNT/C60 coaxial heterojunction. Upon visible light irradiation, an aqueous solution of NH3 and dye@CNT/C60-dendron nanohybrids produced both N2 and H2 in a stoichiometric ratio of 1:3. Action spectra of this reaction clearly demonstrated that the encapsulated dye acted as the photosensitizer, with an apparent quantum yield (AQY) of 0.22% at 510 nm (the λmax of the dye). This study presents the first example of dye-sensitized ammonia decomposition and offers a new avenue for developing efficient and sustainable photocatalytic hydrogen production systems.

The high thrust linear motor used for electromagnetic launch is switched with the anti-shunt thyristor as the switch. During the switching process, different current path states will appear, which will lead to changes in motor parameters and current fluctuation. Aiming at the air-core synchronous linear motor with parallel and series power supply, this paper analyzes the change of current path caused by the change of trigger signal of anti-parallel thyristor in the process of sectionalized stator switching. The motor circuit model of the switching process is derived. A new sectionalized stator switching method is proposed to realize the smooth switching of the sectionalized stator powered linear motor. Finally, the correctness of the analysis and modeling is verified by simulation, and the effectiveness of the sectionalized stator switching method is tested by using the test prototype.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

In permafrost regions, ground surface deformations induced by freezing and thawing threaten the integrity of the built environment. Mapping the frost susceptibility of the ground at a high spatial resolution is of practical importance for the construction and planning sectors. We processed Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) data from thawing seasons 2015 to 2019, acquired over the area of Ilulissat, West Greenland. We used a least-squares inversion scheme to retrieve the average seasonal displacement (S) and long-term deformation rate (R). We secondly investigated two different methods to extrapolate active layer thickness (ALT) measurements, based on their statistical relationship with remotely-sensed surface characteristics. A Generalized Linear Model (GLM) was first implemented, but the model was not able to fit the data and represent the ALT spatial variability over the entire study domain. ALT were alternatively averaged per vegetation class, using a land cover map derived by supervised classification of Sentinel-2 images. We finally estimated the active layer ice content and used it as a proxy to map the frost susceptibility of the ground at the community scale. Fine-grained sedimentary basins in Ilulissat were typically frost susceptible and subject to average seasonal downward displacements of 3 to 8 cm. Areas following a subsiding trend of up to 2.6 cm/yr were likely affected by permafrost degradation and melting of ground ice below the permafrost table. Our approach enabled us to identify frost-susceptible areas subject to severe seasonal deformations, and/or long-term subsidence induced by degrading permafrost. Used in combination with traditional site investigations, InSAR maps provide valuable information for risk management and community planning in the Arctic.

Statistical analysis of mechanical properties of thin-walled samples (~500 microns) obtained by selective laser melting from AlSi10Mg material and subjected to heat treatment for 1 hour at temperatures from 260 °C to 440 °C (step of aging temperature change 30 °C) has shown that the maximum strain hardening in the stretching diagram section from yield strength to tensile strength is achieved at the heat treatment temperature equal to 290 °C. At carrying out of correlation analysis statistically significant positive correlation between deformation corresponding to yield strength and the sum of heights of the largest protrusions and depths of the largest depressions of the surface roughness profile within the basic length of the sample (Rz) and the full height of the surface roughness profile (Rmax) was established. It was found that the reason for the correlation is the presence of cohesive states between the extreme values of the surface roughness profile that persist along the entire length of the specimen.

We can improve our knowledge of the factors influencing women's decisions to have a caesarean section rather than a vaginal delivery, slow the rise in the caesarean section rate, encourage mothers to have vaginal delivery, and provide practical solutions to health system planners through statistical analysis of the proportion of women who prefer caesarean sections. This investigation is cross-sectional. It involved gathering information from 60 women (20–42 years old) who had given birth via caesarean section over four months, beginning in October 2022 and ending in January 2023. The main reasons of a caesarean section were presence of a fibrous node (caused by previous caesarean sections that were repeated) at 16.67%, intrauterine foetal death at 15%, cervical stenosis at 8.33% , 8.33% of births were repeated due to obstructed labour; 6.66% of caesareans were carried out because the mother contracted or had her uterus removed in order to prevent having children. This study found that there were a lot of complications. The bleeding or anaemia cases accounted for the highest percentage of complications (20%), followed by high blood pressure (16.67%), high fever (10%), and either shortness of breath, blood clotting, urinary tract infection, or wound inflammation (10%). The results of the current study indicated that the level of education, the employment of mothers, and the age of the pregnant were the most important social and demographic factors for increasing the rate of caesarean sections

The characteristics of gap plasmon formed by nanoparticle-on-mirror (NPOM) structure composed of metal nanoparticles (MNP) and metal thin films have aroused the interest of various optoelectronic devices. The resonant spectrum obtained by the internal coupling effect of gap can be flexibly controlled by the polarization of incident light and the thickness of the dielectric layer between MNP and metal thin films. We have theoretically studied the resonance spectra of polarization-dependent gold ellipsoidal nanoparticles (GENP) and gold thin films in the gap region of NPOM structures. GENP and gold thin films are separated by a dielectric layer with a refractive index of 1.36. We observe that the intensity of the local electric field resonance peak in the gap region is inversely proportional to the polarization angle. Similarly, the intensity of the local electric field resonance peak in the gap region is inversely proportional to the thickness of the dielectric layer. We have obtained more than 2200 V/m local electric field intensity (dielectric layer thickness 0.3nm). Finally, the resonant peak wavelength of the electric field in the gap region of the NPOM structure is also controlled by the polarization angle of the incident light and the thickness of the dielectric layer.

This study describes a novel method for grading pathological sections of gliomas. Our own integrated hyperspectral imaging system was employed to characterize 270 bands of cancerous tissue samples from microarray slides of gliomas. These samples were then classified according to the guidelines developed by the World Health Organization, which define the subtypes and grades of diffuse gliomas. We explored a hyperspectral feature extraction model called SMLME-Resnet using microscopic hyperspectral images of brain gliomas of different malignancy grades. The model combines the channel attention mechanism and multi-scale image features to automatically learn the pathological organization of gliomas and obtain hierarchical feature representations, effectively removing the interference of redundant information. It also completes multi-modal, multi-scale spatial and spectral feature extraction to improve the automatic classification of glioma subtypes. The proposed classification method demonstrated high average classification accuracy (>97.3\%) and Kappa coefficient (0.954), indicating its effectiveness in improving the automatic classification of hyperspectral gliomas. The method is readily applicable in a wide range of clinical settings, offering valuable assistance in alleviating the workload of clinical pathologists. Furthermore, the study contributes to the development of more personalized and refined treatment plans, as well as subsequent follow-up and adjustment of treatment, by providing physicians with insights into the underlying pathological organization of gliomas.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

The paper presents an analysis of the method of recording the magnetic component of the Earth’s natural pulse electromagnetic field in an urban environment. This method of recording has already proved itself to be a method that allocates the stressed sections of rock mass at mining and, therefore, authors suppose its effectiveness for allocating active tectonic disturbances and forecasting accidents at underground utilities, what will help reduce the potential environmental hazard of these objects.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

The research that we are referring to examines the morphological, structural, and optical characteristics of kesterite (Cu1-xAgx)2ZnSnS4 (CAZTS) thin films, which are produced using a process known as thermal evaporation (TE). The study's main goal was to determine how different Ag contents affect the characteristics of CAZTS systems. X-ray diffraction (XRD) and Raman Spectroscopy: were used to confirm the crystal structure of the CAZTS thin films. Using a mathematical model of spectroscopic ellipsometry, the refractive index (n) represented the part of the complex refractive index, the extinction coefficient (k) portrayed the imaginary one, and also the energy band gap of the fabricated films were all calculated. The energy band gap of the thin films was also calculated. This is a crucial parameter for solar cell applications, as it determines the wavelength of light that the material can absorb. The energy band gap was found to decrease from 1.74 eV to 1.55 eV with increasing Ag content. The ITO/n-CdS/p-CAZTS/Mo heterojunction was well constructed, and the primary photovoltaic characteristics of the n-CdS/p-CAZTS junctions were examined for use in solar cells. Different Ag contents of the CAZTS layers were used to determine the dark and illumination (current-voltage) characteristics of the heterojunctions. The study's findings collectively point to CAZTS thin layers as potential absorber materials for solar cell applications.

Walls-like structured monoclinic WO3 thin films were obtained by spray deposition method for further integration in gas sensors. For sensing applications, it is very important to achieve a high surface-to-volume ratio surface together with a proper thin films structure. The present communication reports on the effect of the sprayed solution volume variation (as a thickness variation element) on the detailed Raman spectroscopy for WO3 thin films with different thicknesses grown from precursor solutions with two different concentrations. Detailed analysis of the two series of samples shows that the growing thickness strongly affects the films morphology while their crystalline structure is only slightly affected. The Raman analysis contribute to refining the structural features clarifications. It was observed that, for both concentrations, the increase in thickness seems to slightly affect the stoichiometry of material and, in association with surface morphology variations, provide new possibilities for fine tuning of films properties towards enhanced as sensing applications. Further studies are ongoing.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

This study compared the efficacy of alfaxalone and propofol to induce anesthesia in bitches undergoing an ovariohysterectomy or cesarean sections. 34 healthy and pyometra-affected females were induced with IV propofol administration, 35 healthy and pyometra-affected bitches were induced with the IV administration of alfaxalone. For the cesarean sections, females were induced with propofol (n=14) or alfaxalone (n=14). Maternal physiological parameters (heart rate, blood pressure, temperature) were recorded throughout surgeries; the viability and a modified Apgar score was recorded in the neonates at 5, 60 and 120 minutes after delivery. The use of propofol and alfaxalone did not show relevant differences over parameters assessed, when ovariohysterectomy was performed in healthy bitches or females with pyometra, as well as when cesarean sections were compared; only, a transient tachycardia appeared after alfaxalone administration. However, a higher percentage of bitches needed extra-doses of propofol. Neonatal mortality was similar between both groups, but when alfaxalone was used a higher neonatal viability was observed. Propofol and alfaxalone showed similar efficacy to perform the ovariohysterectomy in all bitches. Both protocols were optimal for cesarean sections, but alfaxalone was associated with a higher neonatal viability and a higher neonatal survival rate.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

Steel surface protection with hard coatings is essential in the metalworking industry, yet developing high-performance hard coatings still remains a challenge. Quaternary nitride coatings, particularly TiAlSiN, have been extensively studied, but commercial TiAlSiN coatings vary widely, and there is a lack of consistent data. This study presents findings on the development and evaluation of TiAlSiN and TiAlSiN/TiN thin films, with an 800 nm thick TiAlSiN top coating and a 100 nm thick TiN mid-coating. The films were deposited on C120 tool steel discs via reactive DC magnetron sputtering. Ti and TiAlSi 75–20–5 (at.%) disc-shaped targets (50.8 mm diameter × 6.3 mm thickness), fabricated by our team through spark plasma sintering, were used for the sputtering process. Coatings were grown on smooth steel substrates heated to 300 °C, resulting in a uniform micro-structure with nanoparticles of globular (TiN) or pyramidal shape (TiAlSiN), as evidenced by SEM analysis. Nanoindentation tests showed superior mechanical properties for all coatings compared to the steel substrate. Micro-scratch tests indicated better scratch resistance for TiAlSiN/TiN bilayer (BL) coatings than for TiAlSiN single-layer (SL) coatings. Electrochemical impedance spectroscopy tests in a 3.5 wt.% NaCl solution revealed that the BL coatings demonstrated superior corrosion resistance compared to the SL coatings, even after thermal aging at 800 °C for 1 hour. The superior properties of the synthesized TiAlSiN/TiN films recommend them as protective coatings for tool steel surfaces.

Nucleosomes are non-uniformly distributed across eukarytic genomes, with stretches of ‘open’ chromatin strongly associated with transcriptionally active promoters and enhancers. Understanding chromatin accessibility patterns in normal tissue and how they are altered in pathologies can provide critical insights to development and disease. With the advent of high-throughput sequencing, a variety of strategies have been devised to identify open regions across the genome, including DNase-seq, MNase-seq, FAIRE-seq, ATAC-seq, and NicE-seq. However, the broad application of such methods to FFPE (formalin-fixed paraffin embedded) tissues has been curtailed by the major technical challenges imposed by highly fixed and damaged genomic material. Here we review the most common approaches for mapping open chromatin regions, recent optimizations to overcome the challenges of working with FFPE tissue, and a brief overview of a typical data pipeline with analysis considerations.

Corrugated board, widely used in the packing industry, is a recyclable and durable material. Its strength and cushioning, influenced by geometry, environmental conditions like humidity and temperature, and paper quality, make it versatile. Double-walled (or five-ply) corrugated board, comprising two flutes and three liners, enhances these properties. This study introduces a novel approach to analyze 5-layered corrugated board, extending a previously published algorithm for single-walled boards. Our method focuses on measuring layer and overall board thickness, flute height, and center lines of each layer. Integrating image processing and genetic algorithms, the research successfully developed an algorithm for precise geometric feature identification of double-walled boards. Images were recorded using a special device with a sophisticated camera and image sensor for detailed corrugated board cross-sections. Demonstrating high accuracy, the method faced limitations only with very deformed or damaged samples. This research contributes significantly to quality control in the packaging industry and paves the way for further automated material analysis using advanced machine learning and image sensors. It emphasizes the importance of sample quality and suggests areas for algorithm refinement to enhance robustness and accuracy.

The present study reports on the fabrication and performance of ammonia sensors based on single-walled carbon nanotubes (SWCNTs) coated with gold nanoparticles (AuNPs). The sensors were subjected to controlled concentrations of ammonia at two temperatures, namely 25 oC and 140 oC, and their response was monitored through successive cycles of ammonia exposure and nitrogen purging. The results demonstrate that the sputtering-based deposition of AuNPs on SWCNTs led to the best sensor performance, characterized by a rapid increase in resistance values upon exposure to ammonia, and efficient recovery at 140 oC. By contrast, the sensor with chemically impregnated AuNPs exhibited a slower response time. Furthermore, a novel device was developed that combined MoS2-AuNPs (sputtering)-SWCNTs, and it showed improved sensor performance compared to the devices with only AuNPs. Overall, the study provides valuable insights into the fabrication and optimization of SWCNT-based ammonia sensors for various applications, especially for detecting and quantifying small amounts of ammonia (concentrations below 1 ppm).

Corrugated cardboard is an ecological material, mainly because, in addition to virgin cellulose fibers also the fibers recovered during recycling process are used in its production. However, the use of recycled fibers causes slight deterioration of the mechanical properties of the corrugated board. In addition, converting processes such as printing, die-cutting, lamination, etc. cause micro-damage in the corrugated cardboard layers. In this work, the focus is precisely on the crushing of corrugated cardboard. A series of laboratory experiments were conducted, in which the different types of single-walled corrugated cardboards were pressed in a fully controlled manner to check the impact of the crush on the basic material parameters. The amount of crushing (with a precision of 10 micrometers) was controlled by a precise FEMat device, for crushing the corrugated board in the range from 10 to 70 % of its original thickness. In this study, the influence of crushing on bending, twisting and shear stiffness as well as a residual thickness and edge crush resistance of corrugated board was investigated. Then, a procedure based on a numerical homogenization, taking into account a partial delamination in the corrugated layers to determine the degraded material stiffness was proposed. Finally, using the empirical-numerical method, a simplified calculation model of corrugated cardboard was derived, which satisfactorily reflects the experimental results.

The rationalization and modeling of an electric discharge in a fluid require the knowledge of electron swarm parameters. In this work, transport coefficients of alcohols, including methanol, ethanol, propanol, and butanol are reported. The electron energy distribution function, mean energy, reduced mobility, and diffusion coefficient, are calculated using the two-term expansion of the electron Boltzmann equation in the frame of BOLSIG+ and the Monte Carlo collision code METHES. For such, experimental and theoretical values of the electron-alcohol collision cross-section, covering a range of electron impact energy from 1 eV to 1000 eV, are employed. A temperature of 300K, reduced fields E/N between $1-10^4$ Td (1Td = $10^{-21}~\rm Vm^2$), and Plasma density of $10^{19}~\rm m^{-3}$ were used in simulations. The calculated coefficients are compared with data available from previous studies.

The emission of [O I] lines in the coma of Comet 67P/Churyumov-Gerasimenko during the Rosetta mission have been explained by electron impact dissociation of water rather than the process of photodissociation. This is the direct evidence for the role of electron induced processing has been seen on such a body. Analysis of other emission features is handicapped by a lack of detailed knowledge of electron impact cross sections which highlights the need for a broad range of electron scattering data from the molecular systems detected on the comet. In this paper we present an overview of the needs for electron scattering data relevant for the understanding of observations in coma, the tenuous atmosphere and on the surface of 67P/Churyumov-Gerasimenko during the Rosetta mission. The relevant observations for elucidating the role of electrons come from optical spectra, particle analysis using the ion and electron sensors and mass spectrometry measurements. To model these processes electron impact data should be collated and reviewed in an electron scattering database and an example is given in the BEAMD, which is a part of a larger consortium of Virtual Atomic and Molecular Data Centre – VAMDC.

In this study, we demonstrate a high luminous efficacy of 118 lm/W and high reliability through 450°C thermal aging of white LEDs (WLEDs) utilizing four-inch YAG: Ce3+ phosphor-in-glass (PiG) plates designed for vehicle headlights. The sintering process of mixing glass and phosphor typically generates pores, which can scatter light and reduce the luminous efficacy of the fabricated PiG. In this study, we produced four-inch PiG plates under four different fabrication conditions to evaluate their luminous efficacy. Our results revealed that the PiG plate with a thin thickness of 0.08 mm exhibited a 16.83% increase in luminous efficacy compared to the 0.15 mm plate, attributed to reduced light interaction with the pores. Unlike silicone-based phosphor WLEDs, which offer high performance but lower reliability due to the silicone resin's low transition temperature (150°C), our novel thin PiG plate achieves high performance and reliability. This advancement suggests that the proposed thin PiG plate could replace traditional silicone-based phosphors, enabling the development of high-quality WLEDs for vehicle headlights in automotive applications.

Most of the existing studies conducted on FRP-confined concrete considered circular and square concrete columns, while limited studies were on columns with rectangular sections. The studies have confirmed that the circular cross-sections exhibited higher confinement effectiveness, whereas in the case of non-circular cross-sections the efficiency of FRP confinement decreases with an increase of the sectional aspect ratio and there is no significant increase, particularly for columns with the aspect ratio of 2.0. As recently suggested by the researchers, to significantly increase the effectiveness of FRP-confinement for these columns is by modifying a rectangular section to an elliptical or oval section. According to the literature, most of the existing confinement models for FRP-confined concrete under axial compression have been proposed for columns with circular and rectangular cross-sections. However, modeling the axial strength and strain of concrete confined with FRP in elliptical cross-sections under compression is most limited. Therefore, this paper provides new expressions based on limited experimental data available in the literature. For a sufficient amount of FRP-confinement, the threshold value was proposed to be 0.02. Finally, the accuracy of the proposed model was verified by comparing its predictions with the same test database, together with those from the existing models.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

This paper aimed to describe an atlas of the head of the crested porcupine (Hystrix cristata), applying advanced imaging techniques such as MRI. Furthermore, by combining the images acquired through these techniques with anatomical gross sections, we obtained an adequate description of the structures that form the CNS and associated structures of this species. This anatomical information could serve as a valuable diagnostic tool for the clinical evaluation of different pathological processes in porcupines such as abscesses, skull malformations, fractures, and neoplasia.

This paper presents a numerical study of topology-optimised pin-end aluminium alloy columns using finite element analysis (FEA). The FEA models integrate geometric imperfections and material nonlinearity, validated against experimental findings from existing literature. Furthermore, modern design methodologies including Eurocode 9, Direct Strength Method (DSM), and Continuous Strength Method (CSM) are employed to assess the maximum load capacity of such columns. Parametric investigations encompass diverse parameters such as varied cross-sections, column lengths, and global and local imperfections. By analysing a total of 288 FE models, incorporating 16 column cross-sections across two lengths with nine distinct imperfections, the study compares results with those derived from modern design methodologies. Thus, this research elucidates the behaviour of novel cross-sections and the application of contemporary design techniques in their analysis.

In this paper a new approximate procedure is developed for calculating the inclination angle of the end points of statically determinate beams. The method is based on the topology comparison of simple (hinge-roller combination) supported beam and a resemblant cantilever beam. Assuming that the support reactions of the beam are active forces, the virtual displacements at the points of the reaction forces are calculated. Based on these values the inclination angle is calculated. Several examples are considered and the suggested in this paper, while the procedure is applied for various types of structures and loadings. The results, obtained by the suggested numerical procedure, are compared with analytical ones, and they are in good agreement.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

Nowadays asymmetric thin film composite (TFC) polymeric hollow fiber (HF) membranes are extensively used in industrial gas/vapor separations, water treatment etc. There are numerous advantages to use hollow fibers such as: low energy requirements, simplicity of operation, and high specificity. In the present article we discuss the progress made during the past decade in the preparation of the HF substrate and preparation/modification of the thin selective layer. Their applications in water treatment, dehydration of alcohols via pervaporation and gas/vapor separation are also demonstrated.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

Herein, we report on a giant thermoelectric figure of merit of a non-degenerate fluorine-doped single-walled carbon nanotube (FSWCNT) using a tractable analytical approach and the phonon lattice Boltzmann model (LBM). We investigate the influence of the doping concentration, and the overlapping integrals on the ZT. The ZT and the temperature range of operation can be tuned using the doping (impurity) concentration and the overlapping integrals, respectively. The lattice thermal conductivity obtained using the phonon LBM was calculated to be 107.2 W/mK which yielded a ZT greater than 20. Interestingly, the ZT obtained is higher than what has been reported in superlattices, (ZT~1.4) and superlattice nanowire, (ZT~ 4) at 300 K, making FSWCNT a potential candidate for thermoelectric applications.

Human exposure to carbon nanotubes (CNTs) can cause health issues due to their chemical–physical features and biological interactions. These nanostructures cause oxidative stress, also due to endogenous ROS production, which increases following mitochondrial impairment. The aim of this in vitro study was to assess the health effects, due to mitochondrial dysfunction, caused by a sub-chronic exposure to a non-acutely toxic dose of multi walled CNTs (raw and functionalised). The A549 cells were exposed to MWCNTs (2 µg mL^-1) for 36 days. Periodically, cellular dehydrogenases, pyruvate dehydrogenase kinase 1 (PDK1), cytochrome c release, permeability transition pore (mPTP) opening, transmembrane potential (Δψ m), apoptotic cells, and intracellular ROS were measured. The results, compared to untreated cells and to positive control formed by cells treated with MWCNTs (20 µg mL^-1), highlighted the efficiency of homeostasis to counteract ROS overproduction, but a restitutio ad integrum of mitochondrial functionality was not observed. Despite the tendency to restore, the mitochondrial impairment persisted. Overall, the results underlined the tissue damage that can arise following sub-chronic exposure to MWCNTs.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

In this paper, a method of direct spinning is proposed for direct spinning of heterogeneous spun wire-blown holes standard parts and the motherboard mounted on the spin board assemblies. The standardization of the spinneret hole was conducive to improving the machining accuracy and efficiency of the pores, and the spinneret holes could be replaced in time when a hole in the spinneret fails. Moreover; on the other hand, according to the needs of the process of spinning, the spinnerets with various cross-sections were combined and installed on the same motherboard for spinning, and the spinning obtained different bionic new functional products. Based on the results, a finite element model of the standard part of the spinneret hole was developed, and the spinnability of the combinable spinnable spinneret board was verified by simulating the melt flow in the spinneret channel through POLYFLOW software. Further, by the processing of the spinneret, the motherboard was installed into a combined spinneret, and the spinneret assembly was installed on the spinning machine for the experiments. Furthermore, the tow section was observed using a microscope, and the results showed the feasibility of the proposed method.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

In the last years, advances in materials engineering based on adaptive electronics have found a new paradigm to optimize drawbacks in signal processing. A two-layer MnO/ZnO:Zn heterostructure envisioned for frequency adaptive electronic signal processing is synthesized by sputtering where the use of internal states allows reconfigurability to obtain new operating modes at different frequency input signals. An X-Ray Diffraction (XRD) is performed on each layer, MnO:Mn had a cubic and ZnO:Zn a hexagonal structure with preferential growth in [111] and [002] directions respectively. It is determined that the coupling in this heterojunction is compatible with a mismatch less 1 % due texture in each layer which implies a low number of defects. An electrical characterisation with an oscilloscope and signal generator was carried out to obtain the time-response signals and current-voltage (I-V) curves where no degradation is detected when changing from a range of frequencies (100 Hz – 1 MHz). An equivalent circuit is proposed to explain the effects in the interface. Finally, the MnO/ZnO:Zn heterojunction delivers states that are stable, repeatable, and reproducible and it demonstrates how the interaction of the materials can be used in adaptive device applications applying frequencies and internal states as to create new and innovative design schematics, reducing the numbers of components/connections in a system for future sustainable electronics.

For many disciplines of science, all conceivable collisional cross sections and reactions must be precisely known. Although the recent decades were a trial of large-scale research to give these data, many essential atomic and molecular cross section data still missing, and the reliability of the existing cross sections has to be validated. In this paper, we present electron stripping, electron capture, and system breakdown cross sections in carbon (C5+) ions and lithium (Li2+) ions collisions with atomic hydrogen based on the Monte Carlo models of classical and quasi-classical trajectories. According to our expectation, the QCTMC results show higher results in comparison to standard CTMC data, emphasizing the role of Heisenberg correction constraint, especially in the low energy regime. On the Other hand, at high energy, the Heisenberg correction term has less influence as a projectile momentum increase. We present the total cross sections of electron stripping, electron capture, and system breakdown in C5+ ions and Li2+ ions collisions with atomic hydrogen in the impact energy range from 10 keV to 160 keV, which is of interest in astrophysical plasmas, atmospheric sciences, plasma laboratories, and fusion research.

We have established earlier a cell line from the human limbal area to study cell growth and response to the toxic effects of antibiotics used in ophthalmology. In the recent work, the effect of multi-walled carbon nanotubes (MWCNTs) in cornea damage was investigated in vitro and in vivo in mice. In the in vitro experiments, the physiological effects of multi-walled carbon nano-tube (MWCNT) bundles on corneal wound healing were mimicked in vitro by a reepithelization limbal stem cell model. Murine in vivo experiments were performed with intact, non-functionalized MWCNTs to confirm the validity of in vitro tests. The MWCNTs of 10 -30 nm outer diameter at low concentration (5 µg/ml) did not interfere with the wound healing of the damaged limbal cell monolayer. Higher than 50 µg/ml concentrations: a) generated MWCNT aggregates, b) restrained the movement and prolonged the time of wound healing, c) increased the amplitudes of the oscillations of the cells, and d) resulted in scar formation affecting both cor-neal function and refraction. Chromatin condensation, a sensitive test of the viability of cells, including limbal stem cells revealed that the presence of a low concentration of nanotubes (5 µg/ml), did not significantly affect the viability of limbal cells. Chromatin condensation was completed and metaphase chromosomes were seen at higher MWCNT concentration proving that their aggregates did not affect the viability of limbal cells. This concentration of MWCNTs (5 µg/ml) did impact neither the reepithelization in vitro nor in vivo in the scratched eyes of mice. Scar formation took place at higher than 50 µg/ml concentrations and the healing of the cornea was prevented by the lack of movement of increasingly larger macroaggregates. In vivo murine experiments vali-dated in vitro monolayer regrowth followed by time-lapse microscopy portraying realistically the reepithelization of the damaged cornea that process was gradually slowed down by macro aggregate formation and caused the scarring of the cornea.

The Atlantic puffin is a medium-sized seabird with black and white plumage and orange feet. It is distributed mainly along the northern Atlantic Ocean and due, among other reasons, to human activities, it is in a threatened situation and classified as a vulnerable species according to the International Union of Conservation of Nature (IUCN). In this study, we used a total of 20 carcasses of juvenile Atlantic puffins to perform anatomical cross sections and magnetic resonance images. Thus, an adequate description of the head was made, providing valuable information that could be helpful as a diagnostic tool for veterinary clinicians, who increasingly treat these birds in zoos, rehabilitation centers and even in the wild.

The subject of the research is the investigation of the behavior of railway tracks in locations with a significant change in the stiffness of the track. These locations can be designed from various structural elements and their materials, and this mainly results in a height change of the track level during its operation. These transition zones are monitored and expertly examined in order to detect undesirable deformations of the geometrical position of the track caused by the trains running. The transition zones are at the points where the fixed track transitions to the classic track bed, in our case it is their combination with bridge structures, especially at their supports. In Slovakia, under the conditions of the Railways of the Slovak Republic, the issue is topical within the framework of the modernization of trans-European railway corridors. The results of experimental measurements and their analysis will provide relevant data for subsequent research solutions for their new numerical modeling, which will ensure a smooth passage through these points of change without height fluctuations, vibrations, and shocks from the wheels of train sets.

The majority of structures supporting solar panels are founded on thin-walled metal piles driven into the ground to optimize costs and construction timelines. These pile foundations are subjected to repetitive lateral loads from various external forces, such as wind, which can compromise the in-tegrity of the pile-soil system. Given that the proper functioning of photovoltaic solar plants is typically expected for 20-30 years, predicting their useful life under fatigue loading becomes crucial. This research investigates the lateral load response of a single pile subjected to different fatigue loads in stiff cohesive soils. Additionally, the effect of loading cycles on the degradation of pile-soil ad-hesion is studied through pull-out field tests. This study reveals that soil fatigue does not occur under repetitive loading, and the soil’s stiffness remains constant once the cycles causing soil compaction have been overcome. Nevertheless, the soil's accumulated plastic deflection steadily increases once soil compaction due to cyclic loading occurs. The implications of these results on the fatigue life of photovoltaic solar panel foundations are discussed.

Liquid argon technology is widely used by many previous and current neutrino experiments, and it is also promising for future large-scale neutrino experiments. When detecting neutrinos using liquid argon, many hadrons are involved, which can also interact with argon nuclei. In order to gain a better understanding of detection processes, and to simulate neutrino events, knowledge of hadron-argon cross sections is needed. This paper describes a new procedure, which improves upon the previous work with a multi-dimensional unfolding, to measure hadron-argon cross sections in a liquid argon time projection chamber. Through a simplified version of simulation, we demonstrate the validity of this procedure.

To achieve the required mechanical properties in the heat treatment of steel, it is necessary to have an adequate cooling rate and to achieve the desired final temperature of the product. This should be achieved with one cooling unit for different product sizes. In order to provide high variability of the cooling system, different types of nozzles are used in modern cooling systems. Designers often use simplified, inaccurate correlations to predict the heat transfer coefficient, resulting in oversizing of the designed cooling or failure to provide the required cooling regime. This typically results in longer commissioning times and higher manufacturing costs of the new cooling system. Accurate information about the required cooling regime and the heat transfer coefficient of the designed cooling is critical. This paper presents a design approach based on laboratory measurements. Firstly, the way to find or validate the required cooling regime is presented. The paper then focuses on nozzle selection and presents laboratory measurements that provide accurate heat transfer coefficients as a function of position and surface temperature for different cooling configurations. Numerical simulations using the measured heat transfer coefficients allow the optimum design to be found for different product sizes.

Mechanism of traffic congestion generation is more than complicated, due to complex geometric road design and complicated driving behavior at urban expressway in China. We employ Cell transmission model (CTM) to simulate traffic flow spatiotemporal evolution process along the expressway, and reveal the characteristics of traffic congestion occurrence and propagation. Here we apply the variable-length-cell CTM to adapt the complicated road geometry and configuration, and propose the merge section CTM considering drivers' mandatory lane-changing and other unreasonable behavior at on-ramp merge section, and propose the diverge section CTM considering queue length end extending expressway mainline to generate dynamic bottleneck at diverge section. In the new improved CTM model, we introduce merge ratio and diverge ratio to describe the effect of driver behavior at merge and diverge section. We conduct simulation on the real urban expressway in China, results show that merge section and diverge section are the original location of expressway traffic congestion generation, on/off-ramp traffic flow has great effect on expressway mainline operation. When on-ramp traffic volume increases by 40%, merge section delay increases by 35%. And when off-ramp capacity increases by 100 veh/hr, diverge section delay decreases about by 10%, which proves the strong interaction between expressway and adjacent road networks . Our results provide the underlying insights of traffic congestion mechanism in urban expressway in China, which can be used to better understand and manage this issue.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Directed Energy Deposition (DED) processes necessitate a consistent material flow to the melt pool, typically achieved through pneumatic conveying of metal powder via thin pipes. This study aims to record and analyze the multiphase fluid-solid flow. An experimental setup utilizing a high-speed camera and specialized optics was constructed, the flow through thin transparent pipes was recorded. The resulting information was analyzed and compared with coupled Computational Fluid Dynamics - Discrete Element Modeling (CFD-DEM) simulations, with special attention to the solids flow fluctuations. The paper details the experimental design, video analysis using Particle Tracking, and a novel method for deriving volumetric concentrations and flowrate from flat images. The findings confirm the accuracy of the CFD-DEM simulations and provide insights into the dynamics of pneumatic conveying, which could be used to enhance the efficiency of DED processes.

Different materials prepared by appropriate synthesis methods and applying different post syn-thesis processes could be used as hole transport layer in perovskite solar cells. In the present work annealing was employed to enhance physical properties of copper oxide (CuO) thin films fabricated via spin coating technique and the effects of annealing on their optical, morphological, electrical and structural properties were investigated. The XRD findings revealed the polycrystalline structure with large crystallite size. Optical spectra showed larger transmission beyond the visible region, reduced absorption, and a decrease in bandgap energy from 1.93 eV to 1.81 eV. The Ag phonon modes at 299.22 and 304 cm-1 shown by the Raman shift confirmed the development of the CuO pure phase. FTIR spectra showed the Cu-O stretching band at 759, 764 and 446 cm−1. SEM revealed the agglomeration of nano crystallites with large grains on the surface. The carrier type conductivity of annealed CuO thin films was determined via two-point hot probe technique. Low resistivity values were determined via four-point probe method. These findings indicate that CuO thin films may be successfully used as a companion with an n-type layer in p-n junction solar cells, and a hole transport layer in perovskite solar cells.

As a derivative of graphene, graphene oxide (GO) was initially developed by chemists to emulate some of the key properties of graphene, but it was soon recognized as a unique material in its own right, addressing an application space that is not accessible to chemical vapor deposition based materials. Over the past decade, GO has emerged as a new frontier material with tremendous advances in its material fabrication and quality control over its properties. These in turn have led to rapid progress in GO based photonics, electronics, and optoelectronics concepts and devices, evoking new science and paving the way for many technological breakthroughs with exceptional performance. Here, we review the unique fundamental characteristics of GO, its thin film fabrication methods, patterning techniques, and mechanisms for tuning its material properties. This latter capability in particular has enabled novel advanced functional photonic, electronic, and optoelectronic devices. Understanding these insights is essential for designing and tailoring GO properties for state-of-the-art applications including solar energy harvesting, energy storage, medical diagnosis, image displays, and optical communications. We conclude by discussing the open challenges and exciting opportunities of this field, together with future prospects for major technological advancements and breakthroughs.

In this work, the wetting and evaporation behaviour of non-polar solvent droplets on thin soluble coatings is investigated experimentally. The wetting process on spin coated polymer layers by the solvent is captured using shadowgraphy. Initial spontaneous dynamic wetting as well as later stages of wetting are recorded and evaluated. Furthermore, structures obtained by wetting and subsequent evaporation of solvents on polymer coatings are studied by confocal microscopy. The solubility of the substrate has been varied by using polymers with different molecular masses. We observe that initial spreading dynamics does not depend on the molar mass in the studied range. However, we find a strong influence of the molar mass on the late stage wetting dynamics and on the surface structure after solvent evaporation.

This paper gives an overview of the large-scale tectonic styles encountered in orogens worldwide. Thin-skinned and thick-skinned tectonics represent two end member styles recognized in mountain ranges. Both styles are encountered in former passive margins of continental plates. Thick-skinned style including the entire crust and possibly the lithospheric mantle are associated with intracontinental contraction. Delamination of subducting continental crust and horizontal protrusion of upper plate crust into the opening gap occurs in the terminal stage of continent-continent collision. Continental crust thinned prior to contraction is likely to develop relatively thin thrust sheets of crystalline basement. A true thin-skinned type requires a detachment layer of sufficient thickness. Thickness of the décollement layer as well as the mechanical contrast between décollement layer and detached cover control the style of folding and thrusting within the detached cover units. In subduction-related orogens, thin- and thick-skinned deformation may occur several hundreds of kilometers from the plate contact zone. Basin inversion resulting from horizontal contraction may lead to the formation of basement uplifts by the combined reactivation of pre-existing normal faults and initiation of new reverse faults. In most orogens thick-skinned and thin-skinned structures both occur and evolve with a pattern where nappe stacking propagates outward and downward

The calculation of moments of area is one of the most fundamental aspects of engineering mechanics for calculating the properties of beams or for the determination of invariants in different kind of geometries. While a variety of shapes such as circles, rectangles, ellipses or their combinations can be described symbolically, such symbolic expressions are missing for freeform cross-sections. In particular, periodic B-spline cross-sections are suitable for an alternative beam cross-section, e.g. for the representation of topology optimization results. In this work, therefore, a symbolic description of the moments of area of various parametric representations of such B-splines is computed. The expressions found are then compared with alternative computational methods and checked for validity. The resulting equations show a simple way for fast conceptual computation of such moments of area of periodic B-splines.

In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

High-resolution K-shell photoionization cross-sections for the C-like atomic nitrogen ion (N+) are reported in the 398 eV (31.15 Å) to 450 eV (27.55 Å) energy (wavelength) range. The results were obtained from absolute ion-yield measurements using the SOLEIL synchrotron radiation facility for spectral bandpasses of 65 meV or 250 meV. In the photon energy region 398 eV - 403 eV, 1s⟶2p autoionizing resonance states dominated the cross section spectrum. Analyses of the experimental profiles yielded resonance strengths and Auger widths. In the 415 eV - 440 eV photon region 1s⟶1s2s22p2 4Pnp and 1s⟶1s2s22p2 2Pnp resonances forming well-developed Rydberg series up n=7 and n=8 , respectively, were identified in both the single and double ionization spectra. Theoretical photoionization cross-section calculations, performed using the R-matrix plus pseudo-states (RMPS) method and the multiconfiguration Dirac-Fock (MCDF) approach were bench marked against these high-resolution experimental results. Comparison of the state-of-the-art theoretical work with the experimental studies allowed the identification of new resonance features. Resonance strengths, energies and Auger widths (where available) are compared quantitatively with the theoretical values. Contributions from excited metastable states of the N+ ions were carefully considered throughout.

Double-walled carbon nanotube-yttria-stabilized ZrO2 nanocomposites are prepared by a mixing route followed by Spark Plasma Sintering. Incorporation of carbon at contents higher than 2 wt.% results in significantly lower friction coefficients, both against alumina and steel balls. Double-walled carbon nanotubes improve wear resistance and reduce friction without severe damage, contrary to multi-walled carbon nanotubes.

In this paper, a kind of single-walled carbon nanotube nonlinear model is developed, and the strongly nonlinear dynamic characteristics of such carbon nanotubes subjected to random magnetic field are studied. The nonlocal effect of microstructure is considered based on the theory of nonlocal elasticity. The natural frequency of the strongly nonlinear dynamic system is obtained by the energy function method, the drift coefficient and the diffusion coefficient are verified. The stationary probability density function of the system dynamic response is given and the fractal boundary of the safe basin is provided. Theoretical analysis and numerical simulation show that stochastic resonance occurs when varying the random magnetic field intensity. The boundary of safe basin has fractal characteristics and the area of safe basin decreases when the intensity of the magnetic field permeability increases.

This paper reports results of analysis of field ion emission mechanism from tungsten-epoxy composite emitters that are compared to tungsten nano-field emitters. In this context, the mechanism of emission from this type of emitters is described based on a theory of induced conductive channels. The tungsten emitters were prepared using the electrochemical polishing technique and coated with a layer of the epoxy resin. Field ion microscope (FIM) analyses are reported including the study of the emission-ion density distributions from both the uncoated and coated emitters. Two forms of emission patterns have been observed in the ion emission microscopy technique describing the differences in the emission mechanism of both types of emitters. The observed results show: (a) the expected crystalline surface atomic distribution images of the field ion microscopy in the case of uncoated tungsten tips, and (b) randomly distributed emission spots that describe the locations of the induced conductive channels inside the resin coating layer.

In this paper, a novel nonlocal strain gradient anisotropic elastic shell model is developed to analyse the vibrations of simply supported single‒walled carbon nanotubes (SWCNTs). Sanders‒Koiter shell theory is used to obtain the strain‒displacement relationships. Eringen nonlocal elasticity theory and Mindlin strain gradient theory are adopted to derive the constitutive equations, where the anisotropic elastic constants are expressed via Chang molecular mechanics model. The complex variable method is used to analytically solve the equations of motion and to obtain the natural frequencies of SWCNTs. First, the anisotropic elastic shell model is validated via comparisons with the results of molecular dynamics simulations reported in the literature. Then, the effect of nonlocal and material parameters on the natural frequencies of SWCNTs with different geometries and wavenumbers is analysed. From the numerical simulations it is obtained that the natural frequencies decrease with increasing nonlocal parameter, while they increase with increasing material parameter. Moreover, the decrease of natural frequencies with increasing SWCNT radius is exponential as the material parameter increases, while it is linear as the nonlocal parameter increases. Finally, as the number of waves increases, the natural frequencies linearly vary with increasing nonlocal parameter, while they exponentially increase with increasing material parameter.

Multi-walled carbon nanotubes are engineered nanomaterials (ENMs) that have a fiber-like structure which may be a concern for the development of cellular senescence. Premature senes-cence, a state of irreversible cell cycle arrest, is implicated in the pathogenesis of chronic lung dis-eases such as pulmonary fibrosis (PF). However, the crosstalk between downstream pathways mediating fibrotic and senescent responses of MWCNTs is not well defined. Here, we exposed human bronchial epithelial cells (BEAS2B) to MWCNTs for up to 72 hours and demonstrate that MWCNTs increase reactive oxygen species production (ROS) accompanied by inhibition of cell growth and proliferation. In addition, exposure resulted in the increase of p21 protein and senes-cence associated β-galactosidase (SA β-gal) activity. We also determined that co-exposure with the cytokine, transforming growth factor-β (TGF-β) exacerbated cellular senescence indicated by increased protein levels of p21, p16, and γH2A.X Furthermore, the production of fibronectin and plasminogen activator inhibitor (PAI-1) was significantly elevated with the co-exposure compared to MWCNTs or TGF-β alone. Together, this suggests that the senescence potential of MWCNTs may be enhanced by pro-fibrotic mediators in the surrounding microenvironment.

The present investigation deals with the adsorption of chromium(III) from alkaline media using multi-walled carbon nanotubes. The adsorption of Cr(III) has been studied under various experimental conditions: stirring speed of the aqueous solution, initial metal and adsorbent concentrations, NaOH concentration in the aqueous solution, and temperature. The rate law indicated that chromium adsorption is well represented by the particle diffusion model, whereas the adsorption process fits to the pseudo-second order kinetic model within an exothermic character. Equilibrium data fit to the Langmuir type-2 equilibrium isotherm in an spontaneous process. Chromium(III) can be eluted from metal-loaded nanotubes using acidic solutions, from which fine chromium(III) oxide pigment can be ultimately yielded.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

Highly macroporous thin films of WO₃ were fabricated on transparent conductive substrates by application of a polymeric organic paste loaded with an amine/tungstate complex. After spin-coating and annealing at 550^oC, the resulting yellow films are found to be comprised of channeled array of clustered nanoparticles. These channels are confirmed by scanning electron microscopy to extend through the entire length of the coating. The high porosity of the material enables the insertion of a co-catalyst into the internal structure of the film. These internally functionalized composites demonstrate good photosensitivity and stability in neutral electrolyte.

Reproductive disorders are a common event in modern reproductive medicine, occurring both in spontaneous and assisted pregnancies. Studies of the molecular mechanisms of implantation disorders in thin endometrium, including the study of gene transcriptional activity, have shed light on the identification of potential biological markers of endometrial receptivity. Background/Objectives: to reveal significantly dysregulated selected genes expression between RIF and RPL patients with thin endometrium. Methods: Endometrial samples were collected in the implantation window days (LH+7 – LH+10) of the natural menstrual cycle from RIF patients (n=20) and RPL patients (n=19). Ten genes were chosen as target genes regarding their possible relations with the implantation process. Total RNA was purified, reverse-transcribed; gene expression was quantified by RT-PCR. Results: The expression of the IL-15, INFG and HPRT1 genes were significantly decreased in RIF with thin endometrium patients compared to the RPL patients (log2 fold change=0.92, p=0.023 for IL-15, log2 fold change=1.24, p=0.046 for INFG, and log2 fold change=0.579, p=0.046 for HPRT1). There were not significant differences in expression of CXCL8, CXCL1, MMP10, C4BPA, TNC, VEGFB and HAND2 genes between groups. Conclusions: decreased expression of IL-15, INFG and HPRT1 genes was found in patients with RIF with thin endometrium compared to the endometrium of women with RPL. This has practical significance for clinicians for differentiated prescription of immunomodulatory therapy in patients undergoing ART programs.

The cold-formed steel sections are becoming popular for different steel structures because it has a high resistance against the different straining actions with minimum weight compared with hard steel sections. Recently, the perforated cold-formed steel (PCFS) sections are used in many applications such as storage perforated uprights racks. Experimental research into the behaviour of steel storage rack uprights subjected to axial compression is presented in this paper. The material qualities of cold-formed steel uprights were determined by tensile tests. The seventeen perforated specimens were examined under axial compression, with five different cross-sections, three different web heights and thicknesses, and varying lengths. The study's goals are to find out how perforations affect the performance and failure mode of steel storage rack uprights, discuss the interaction of distortional and global buckling, and verify the accuracy of using the Direct Strength Method (DSM) for predicting the ultimate strength of uprights failing in buckling interactions for perforated uprights. It is found that the failure modes of perforated specimens with stiffeners generally cannot be well predicted by the Direct Strength Method. But when the modifications proposed by Xianzhong Zhao etc. al. are used, their accuracy is acceptable.

The Italian herbal products market is the most prosperous in Europe. The proof is represented by the use of these products in several marketing categories, ranging from medicine to nutrition and cosmetics. Market and legislation in Italy are at the same time cause and consequence of this peculiar situation. In fact, the legislation on botanical food supplements in Italy is very permissive and at the same time the market shows an overall satisfaction of users and strong feedback in terms of consumption, which brings a widening use of medicinal plants, formerly the prerogative of pharmaceuticals, to other fields such as nutrition. This review summarizes the market and normative panorama of herbal products in Italy, highlighting the blurred boundaries of health indications, marketing authorizations and quality controls between herbal medicines and non pharmaceutical products, such as food supplements, cosmetics and other herbal-based “parapharmaceuticals”.

In this contribution we present work on rapid thermal annealing of as-electrodeposited thin films of Cu2ZnSnS4. The treatment was carried out in cold wall tubular reactor in dynamic conditions with variations of temperature, speed and time of the specific elements of the process. The effect of annealing was investigated by X-ray diffractometry, Raman scattering and Scanning Electron Microscopy (SEM). The phase composition of the films in dependence on conditions of treatment was analysed and have been shown that in slow and prolonged high-temperature process the low temperature binaries react completely and only Kesterite and ZnS is left. In addition, structural investigations by XRD have shown gradual decrease of crystallite sizes when the temperature level and duration of the high-temperature segment increases and respectively increase in the strain, due to formation of the phases in non-equilibrium conditions. In opposite, when the speed of dynamic segments in the process decreases the both crystallite size and strain of the Kesterite decreases non-monotonically. The grain sizes of Kesterite, presented by SEM investigations, have shown increase when the temperature and the duration increase, respectively the speed decreases with exemption at higher temperature near 750 C. The set of experiments gave idea by scrupulous analysis of Raman data to elucidate the track for fine manipulating of the defects in the structure of CZTS thin films having in mind the dependences of the ratios of Q = I287/I303 and Q’= I338/(I366+I374) on the process variables.

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO2 thin films were elucidated using real-time synchrotron radiation imaging, its structure determined using grazing incidence X-ray diffraction (GIXRD), its morphology imaged using the field emission scanning electron microscopy (FESEM), and its surface topography examined using the atomic force microscope (AFM) in contact mode. Cubical white spots were detected, identified as Ag, while the TiO₂ thin film resembles a porous ring-like structure with each ring coalescing and forming channels. Junction growth is directly proportional with time under continuous heating conditions (annealing), and its growth orientations and patterns were seemingly random.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

Tunnel-interchange connecting sections pose significant safety challenges on mountainous expressways due to their high incidence of accidents. Improving road safety necessitates a comprehensive understanding of driver behavior in such areas. This study explores the influences of road characteristics, signage information volume, and traffic conditions on drivers' car-following and lane-changing behavior in tunnel-interchange diverging areas. Utilizing driving data from 25 subjects of 72 simulated road models, driving performance is assessed using Friedman rank test and multivariate variance analysis. The results highlight the significant influence of both connection distance and signage information load on driving behavior. In tunnel-interchange scenarios, the reduction of velocity increased by 62.61%, and speed variability surged by 61.11%, indicating potential adverse effects on driving stability due to the environmental transitions. Decreased connection distances are associated with reduced lane-changing durations, larger steering angles, and increased failure rates. Furthermore, every two units increase in signage information leads to a 13.16% rise in maximum deceleration and a 5% increase in time headway. Notably, the signage information volume shows a significant interaction with connection distance (F=1.60, P=0.045) for most car-following indicators. Hence, the study recommends a maximum connection distance of 700 m and signage information not exceeding nine units for optimal safety and stability.

Abstract: The ever-increasing use of motor vehicles causes a number of traffic safety and community issues, which are particularly severe in cities, accompanied with scarcity of parking spaces and challenges encountered in the road layout alteration projects. The commonly applied solutions include designation of through streets and implementation of on-street parking on residential streets and retrofitted traffic calming measures (TCMs). This article presents the results of the study conducted on a two-way street where Metered Parking System MPS was implemented together with diagonal and parallel parking spaces, refuge islands, horizontal deflection and lane narrowing by a single-sided chicane. The aim of this study was to identify those TCMs that effectively helped to reduce the island approach speed. Heuristic method was applied to assess the effect of the respective TCMs on reducing the island approach speed and the key speed reduction determinants were defined using cause and effect diagram and Pareto chart. Comparative analyses were carried out to rate the respective TCMs as effective, moderately effective or ineffective. Section 1 of this article presents the output of the literature review on urban parking analyses and TCM efficacy. Section 2 presents the study site and the applied heuristic method. The study results are presented in Section 3. Section 3 defines the determinants on the cause and effect diagram and analyses the determinants using the Pareto chart. The final conclusions and comments are given in Section 5. Although the study was limited to a single street in Poland, the findings may hold true in other countries where similar TCMs are used.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

Historical city textures are living history embodying public open spaces of former civilizations, their landscapes and traditional life cultures, carrying them to the present and giving them life. The squares, which form the public open spaces, have been important meeting centers in the social lives of people. City furniture are the important elements in these public open spaces, reflecting the identity of the city and improving quality of life. City furniture improve the reflection of cultural value in historical city textures and their usability. The walled city center, where the historical city texture of Nicosia lies, has a very rich historical texture with the cultural heritage of various civilizations in the history of Cyprus. Public open spaces within the texture, which have acquired the quality of squares with their functions throughout the social history of Nicosia, are still important social spaces for the people of the city. This study analyzed Asmaaltı and Selimiye Squares, two important spaces of the walled city, through examining the city furniture in terms of their material, shape, and functionality, and their conformity with the historical texture. Their deficiencies and nonconformities with the historical texture were identified accordingly. In consideration with such examples, city furniture in historical city textures were assessed for their conformity with the texture characteristics, architectural styles, social, cultural, and economical characteristics, and relevant recommendations are presented respectively.

Tarihi kent dokuları, eski uygarlıkların kamusal açık alanlarını, peyzajlarını ve geleneksel yaşam kültürlerini bünyesinde barındıran, günümüze taşıyan ve yaşatan yaşayan bir tarihtir. Kamusal açık alanları oluşturan meydanlar, insanların sosyal yaşamlarında önemli buluşma merkezleri olmuştur. Kent mobilyaları bu kamusal açık alanlarda kentin kimliğini yansıtan ve yaşam kalitesini artıran önemli unsurlardır. Kent mobilyaları, kültürel değerlerin tarihi kent dokularına yansımasını ve kullanılabilirliğini artırır. Lefkoşa'nın tarihi kent dokusunun yattığı Suriçi kent merkezi, Kıbrıs tarihindeki çeşitli uygarlıkların kültürel mirası ile oldukça zengin bir tarihi dokuya sahiptir. Doku içinde kamusal açık alanlar, Lefkoşa'nın sosyal tarihi boyunca işlevleriyle meydan niteliği kazanan meydanlar, kent insanı için halen önemli sosyal mekanlardır. Bu çalışmada, Suriçi kentin iki önemli mekanı olan Asmaaltı ve Selimiye Meydanları, kent mobilyaları malzeme, biçim, işlevsellik ve tarihi dokuya uygunluk açısından incelenerek incelenmiştir. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur. kentliler için hala önemli sosyal mekanlardır. Bu çalışmada, Suriçi kentin iki önemli mekanı olan Asmaaltı ve Selimiye Meydanları, kent mobilyaları malzeme, biçim, işlevsellik ve tarihi dokuya uygunluk açısından incelenerek incelenmiştir. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur. kentliler için hala önemli sosyal mekanlardır. Bu çalışmada, Suriçi kentin iki önemli mekanı olan Asmaaltı ve Selimiye Meydanları, kent mobilyaları malzeme, biçim, işlevsellik ve tarihi dokuya uygunluk açısından incelenerek incelenmiştir. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur. ve tarihi dokuya uygunluğu. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur. ve tarihi dokuya uygunluğu. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur.

The preparation of sulfur-single walled carbon nanohorns active material via a simple and sustainable evaporation method for application as cathode in lithium-sulfur batteries is reported. We show that the synthesis process enables the infiltration of elemental sulfur within the carbon nanohorns thus obtaining a morphology responsible for the ameliorating of the shuttle effect. The sulfur-carbon composite is characterized in terms of structure, morphology, and composition through x-ray diffraction, transmission electron microscopy, and thermogravimetric analyses. From the electrochemical point of view, cyclic voltammetry, rate capability, and galvanostatic cycling tests are performed employing a solution of bis(trifluoromethane)sulfonimide lithium salt and lithium nitrate in a mixture of 1,2-dimethoxyethane and 1,3-dioxolane in order to evaluate the electrode design applicability within lithium-sulfur cells. In this respect, further insights are provided by the estimation of the lithium-ion diffusion coefficient through the Randles-Sevcik equation, and by electrochemical impedance spectroscopy. The obtained results reveal a remarkable cycle life lasting around 800 cycles with a stable capacity of 520 mA h g-1 for the first 400 cycles at C/4, while reaching a value around 300 mA h g-1 at the 750th cycle. These results suggest sulfur-carbon nanohorns active material as a potential candidate for the next-generation battery technology.

High-density polyethylene (HDPE) waste poses a significant environmental challenge due to its non-biodegradable nature and the vast quantities generated annually. However, conventional recycling methods are energy-intensive and often yield low-quality products. Herein, HDPE waste is upcycled into anti-aging superhydrophobic thin films suitable for outdoor applications. A two-layer spin-casting method combined with heating-induced crosslinking is utilized to produce an exceptionally rough superhydrophobic surface, featuring a root mean square (RMS) roughness of 50 nm, an average crest height of 222 nm, an average trough depth of –264 nm, and a contact angle (CA) of 148°. To assess durability, weathering tests were conducted, revealing the films' susceptibility to degradation under harsh conditions. The films' resistance to environmental factors is improved by incorporating a UV absorber, maintaining their hydrophobic properties and mechanical strength. Our research demonstrates a sustainable method for upcycling waste into high-performance, weather-resistant superhydrophobic films.

We present organic, diamagnetic materials based on structurally simple (hetero-) tolane derivatives. They form crystalline thin-film aggregates that are suitable for Faraday rotation (FR) spectroscopy. The resulting new materials are characterized appropriately by common spectroscopic (NMR, UV-Vis), microscopy (POM), and XRD techniques. The spectroscopic studies give extremely high FR activities thus makes these materials promising candidates for future practical applications. Other than a proper explanation, we insist in the complexity of designing efficient FR materials starting off from single molecules.

New advances in creating effective and affordable copper-based catalysts for water splitting represent a promising strategy for driving sustainable energy technologies. However, ma- terials containing copper are susceptible to corrosion and agglomeration. In this study, we describe a synthesis route to produce olamine-functionalized CuO nanoparticles using the Hot Injection method. Nanoparticles were obtained and subsequently deposited on FTO substrates, undergoing thermal treatment at 500°C and 600°C in atmospheres containing O2 and N2, aiming to enhance the adhesion of the active material to the substrate and modify its oxidation state. Microstructural properties were analyzed using XRD, SEM, and TEM, while electrochemical properties were studied using CV, LSV, and EIS. Electrodes treated thermally in an N2 atmosphere at 600°C exhibited higher ESCA, indicating a greater area of active sites exposed to surface reactions and, therefore, superior catalytic activity in Hy- drogen Evolution Reaction (HER). These findings show an interesting strategy for avoiding rapid electron-hole recombination and, consequently, CuO corrosion. For Oxygen Evolution Reaction (OER), samples treated thermally in O2 atmosphere at 500°C and 600°C appear to be more effective.

Integrated photonic devices operating via optical nonlinearities offer a powerful solution for all-optical information processing, yielding processing speeds that are well beyond that of electronic processing as well as providing the added benefits of compact footprint, high stability, high scalability, and small power consumption. The increasing demand for high-performance nonlinear integrated photonic devices has facilitated the hybrid integration of novel materials to address the limitations of existing integrated photonic platforms, such as strong nonlinear optical absorption or an inadequate optical nonlinearity. Recently, graphene oxide (GO), with its large optical nonlinearity, high flexibility in altering its properties, and facile fabrication processes, has attracted significant attention, enabling many hybrid nonlinear integrated photonic devices with improved performance and novel capabilities. This paper reviews the applications of GO to nonlinear integrated photonics. First, an overview of GO’s optical properties and the fabrication technologies needed for its on-chip integration is provided. Next, the state-of-the-art GO nonlinear integrated photonic devices are reviewed, together with comparisons of the nonlinear optical performance of different integrated platforms incorporating GO. Finally, the challenges and perspectives of this field are discussed.

In a thin-volume photobioreactor where a concentrated suspension of microalgae is circulated throughout the established spatial irradiance gradient, microalgal cells experience a time-variable irradiance. Deploying this feature is the most convenient way of obtaining the so-called “flashing light” effect, improving biomass production in high irradiance. This work investigates the light flashing features of sloping wavy photobioreactors, a recently proposed type, by introducing and validating a Computational Fluid Dynamics model. Two characteristic flow zones (straight top-bottom stream and local recirculation stream), both effective toward light flashing, have been found and characterised: a recirculation-induced frequency of 3.7 Hz and straight flow-induced frequency of 5.6 Hz were estimated. If the channel slope is increased, the recirculation area becomes less stable while the recirculation frequency is nearly constant with flow rate. The validated CFD model is a mighty tool that could be reliably used to further increase the flashing frequency by optimising the design, the dimensions, the installation and the operational parameters of the sloping wavy photobioreactor.

In this study, a flexible strain sensor is devised using corrugated poly(3-hexylthiophene) (P3HT) thin film. In the previous studies, the P3HT-based photoactive thin film was shown to generate direct current (DC) under broadband light, and the generated DC voltage varied with applied tensile strain. Yet, the mechanical resiliency and strain sensing range of the P3HT-based thin film strain sensor were limited due to relatively more brittle thin film constituent—poly(3,4-ethylenedioxythiophene)-polystyrene(sulfonate) (PEDOT:PSS) conductive thin film as a bottom electrode. To address this issue, it is aimed to design mechanically resilient strain sensor using corrugated thin film constituents. Buckling is induced to form corrugation in the thin films by applying pre-strain to the substrate, where the thin films are deposited, and releasing the pre-strain afterwards. It is known that corrugated thin film constituents exhibit different optical and electronic properties from non-corrugated ones. Therefore, to optimize design of the flexible strain sensor, it was studied to understand how the applied pre-strain and thickness of the PEDOT:PSS thin film affect the optical and electrical properties. Also, pre-strain effect on light absorptivity of the corrugated P3HT-based thin films was studied. In addition, strain effect was investigated on the optical and electrical properties of the corrugated thin film constituents. Finally, flexible strain sensors are fabricated by following the design guideline, which is suggested from the studies on the corrugated thin film constituents, and DC voltage strain sensing capability was validated. As a result, flexible strain sensor exhibited tensile strain sensing range up to 5% at frequency up to 15 Hz with maximum gage factor ~7.

A comparative study of the photocatalytic decoloration of methylene blue (MB) dissolved in water was conducted, using three semiconductor oxides: zinc oxide (ZnO), tin oxide (SnO2) and titanium dioxide (TiO2) in the form of thin films and varying their thickness ~ 100, 200, and 300 nm for each film. All the films were deposited using the cost-effective dip-coating technique, at moderate temperature processing (400 °C) with sol-gel solutions on cheap glass substrates. The structural, morphological, and compositional properties of the films were analyzed by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Raman spectroscopy, respectively. The degradation of MB was studied by varying both thickness and type of semiconductor oxides through measurements of optical absorbance of decolorated liquid by photocatalytic process. Structural analysis shows that ZnO and SnO2 films were polycrystalline with preferential growth of (002) and (110) planes respectively, whereas, an amorphous structure was observed for TiO2 films. In addition, morphological properties confirms that the surfaces of all the films are conformed with nano grains in round and irregular shapes. Based on all results reported in this work, that authors believe that the degradation efficiency of MB depends on the thickness of the film and the type of semiconductor material used as a catalyst. The highest degradation efficiencies were recorded with an exposure time of 120 min and with an initial concentration of 10 mg/L for ZnO, SnO2, and TiO2 films were: 100, 88 %, and 76 %, respectively.

Polyanilines are a class of conductive polymers that have attracted significant interest in the field of organic electronics due to their unique properties. In this article, the fluorescence spectroscopy and photovoltaic properties of polyaniline-based thin films and copolymers are investigated. The study focuses on understanding the relationship between the composition and structure of polyanilines and their optical and electrical properties. The article discusses the results of experiments on the photoluminescent properties of S1-S9 copolymers in a DMSO solution and of thin-film photoresistors based on polyanilines. The findings reveal that the photovoltaic properties of the thin films depend on the conditions of their fabrication and their surface morphology. The solubility of polyanilines is excellent, making the production of electronic components compatible with modern printing technologies in organic electronics. The work also points out that the photoconductivity of polyanilines can be improved by incorporation of additional molecular groups into the polymer matrix. Overall, this study sheds light on the potential of polyanilines as promising materials for organic electronics and provides insights into how their properties can be optimized for specific applications.

Laminate structures composed of stiff plates and thin soft interlayers are widely used in aerospace, automotive and civil engineering encouraging the development of reliable non-destructive strategies for their condition assessment. In the paper, elastodynamic behaviour of such laminate structures is investigated with emphasis on its application in ultrasonic based NDT and SHM for the identification of interlayer mechanical and interfacial contact properties. A particular attention is given to the practically important frequency range, in which the wavelength considerably exceeds the thickness of the film. Three layer model with spring-type boundary conditions employed for imperfect contact simulation is used for numerical investigation. Novel effective boundary conditions are derived via asymptotic expansion technique and used for analysis of the peculiar properties of elastic guided waves in considered laminates. It is revealed that the thin and soft film influences the behaviour of the laminate mainly via the effective stiffnesses being a combination of the elastic moduli of the film, its thickness and interface stiffnesses. To evaluate each of these parameters separately (or to figure out that the available experimental data are insufficient), a step-wise procedure employing the effective boundary conditions is proposed and tested versus the laser Doppler vibrometry data for Lamb waves in Aluminium/Polymer film/Alumunium structure. The possibility of using film-related thickness resonance frequencies to estimate the film properties and contact quality is also demonstrated. Additionally, the rich family of edge waves is also investigated, and the splitting of fundamental edge waves into pairs is revealed.

Conjugated polymers (CPs) offer potentials for sustainable semiconductor devices due to their low cost, and inherent molecular self-assembly. Enhanced crystallinity and molecular orientation in thin films of solution-processable CPs have significantly improved organic electronic device per-formance. In this work, three methods namely spin-coating, dip-coating, and unidirectional float-ing-film transfer method (UFTM) were utilized with their parametric optimization for fabricating RR-P3HT films. These films were then utilized for their characterization via optical and micro-structural analysis to elucidate dominant roles of molecular orientation, and crystallinity in con-trolling charge transport in organic field-effect transistors (OFETs). OFETs fabricated by RR-P3HT thin films using spin-coating and dip-coating displayed field-effect mobility (μ) of 8.0 × 10-4 cm2V-1s-1 and 1.3 × 10-3 cm2V-1s-1, respectively. This two-time enhancement in (µ for dip-coated films was attributed to its enhanced crystallinity. Interestingly, UFTM films based OFETs demon-strated μ of 7.0 × 10-2 cm2V-1s-1, >100 times increment as compared to its spin-coated counterpart This superior device performance is attributed to synergistic influence of higher crystallinity and molecular orientation. Since the crystallinity of dip-coated and UFTM-thin films are similar ~50 times improved µ of UFTM thin films suggest a dominant role of molecular orientation as com-pared to crystallinity in controlling the charge transport.

Nowadays recurrent implantation failure (RIF) after invitro fertilization is common problem that reproductive specialists usually faced. The phenomenon of thin endometrium in RIF patients has yet not completely understood and properly treated. This study aimed to reveal significantly dysregulated selected genes expression between RIF patients with thin endometrium and fertile women. Endometrial samples were collected in the implantation window days (LH+7 – LH+10) of the natural menstrual cycle from RIF patients (n=20) and fertile women (n=14). Ten genes were chosen as target genes regarding their possible relations with the implantation process. Endometrial gene expression levels showed differences in RIF samples compared to fertile samples. The significant downregulation was observed for CXCL1 (p=0.005) and C4BPA (p=0.03) genes. There was no statistically significant difference between the RIF groups and the fertile group in the expression of 8 genes: CXCL8, HPRT1, MMP10, INFG, VEGFB, HAND2, IL15 and TNC (p>0.05). The use of a combination of two markers (C4BPA + CXCL1) allows for good discrimination of RIF patients from fertile women (AUC 0.806).

The main aspects of mercury sulfide and mercury selenide thin film synthesis using the chemical deposition method are considered. An analysis of various factors affecting film properties was conducted, including the study of how the nature of the substrate and its pre-treatment influence film properties. The effects of the working solution's temperature, deposition time, and annealing conditions on film characteristics were investigated. The impact of these parameters on the phase composition, as well as optical, electrical, and morphological properties of the films, is discussed and summarized. The paragraph also explains how the choice and concentration of initial reagents affect the parameters, characteristics, and properties of the obtained films.