The definition of UTC in 1972 balanced the needs of the time and frequency community for a universal time scale that was traceable to the definition of frequency in the SI system of units with the needs of the astronomical community for a time scale that was closely linked to UT1, a time scale related to the rotation of Earth. The balance between these two considerations has changed very significantly since 1972, and there is widespread agreement that the method of relating UTC to UT1 should be changed by increasing the maximum tolerance between the two scales to more than the current limit of 0.9 s. I propose to realize this decision by means of an algorithmic adjustment process based on the variation in the length of the day over the previous centuries. I use these historical data to extrapolate the length of the day for a century into the future, and to compute a periodic rate adjustment to UTC based on this extrapolation. The adjustment process will not use time steps. The magnitude of the periodic rate adjustment will be re-considered every century, but the basic adjustment algorithm will not change. I suggest a maximum tolerance between UT1 and UTC that is large enough to absorb the irregular and unpredictable variations in the length of the day with respect to the long-term average increase in this value but plays no role in determining the parameters of the adjustment process that is proposed. I also propose that the adjustment be implemented at 12 UTC on 1 January since that is closest to a universal holiday in all time zones.

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

Abscisic acid (ABA) plays a major role in promoting ripening in sweet cherry, a non-climateric fruit. Exogenous application of ABA has been performed to study fruit ripening and cracking, but this growth regulator is not used for commercial production. To determine the potential of this growth regulator to improve sweet cherry fruit quality, ABA canopy spraying was assayed in four cultivars. Canopy spraying of S-ABA significantly: 1) enhanced sweet cherry fruit color in ‘Glenred’, ‘Lapins’ and 'Bing' cultivars, but not in ‘Royal Rainier’ (a bi-colored cultivar), and 2) decreased fruit size and firmness in ‘Lapins’, ‘Bing’ and ‘Royal Rainier’. Seasonally reproducible effects were seen in ‘Lapins’ (mid/late-maturing) but not in ‘Glenred’ (early-maturing). Canopy spraying of nordihydroguaiaretic acid (NDGA) decreased color and increased fruit size in ‘Lapins’, but not in ‘Glenred’. Direct application of ABA on fruits attached to the tree, without application to the foliage, increased Lapins' fruit color without reducing size. These results suggest a localized fruit response to exogenous ABA application on fruit color development, but that a decrease in fruit size may be due to the effects of exogenous ABA on the tree canopy foliage.

Background: Patients with thromboembolic disease, prosthetic valves, or coagulation issues are commonly prescribed anticoagulants and antiplatelets. Although common professional oral hygiene might not represent a health concern for these patients, anticoagulant and antiplatelet medication might constitute a challenge for dentists and dental hygienists since possible prolonged bleeding might interfere with dental procedures. The aim of the present study was to investigate the bleeding time of different anticoagulants and antiplatelets during a professional hygiene session adapting the Ivy test to the oral environment; Methods: 93 consecutive patients undergoing professional oral hygiene were recruited. Debridement during oral hygiene was performed using ultrasonic mechanical instrumentation, and bleeding sites were assessed and treated with gentle pressure using sterile gauzes. The time for bleeding cessation was recorded. Patients were categorized into six groups based on their drug intake, Control: no anticoagulants or antiplatelets DTI: direct thrombin inhibitors (dabigatran) AntiXa: directa factor Xa inhibitors (endoxaban, apixaban, rivaroxaban) VKA: vitamin K antagonists (warfarin, acenocoumarol) SAPT: single anti-platelet therapy (acetylsalicylic acid or clopidogrel) DAPT: dual anti-platelet therapy (acetylsalicylic acid and clopidogrel). Bleeding time was measured in seconds and mean values were assessed among the different groups. Differences between groups were investigated with Kruskal-Wallis test followed by Dunn’s post-hoc correction for multiple comparisons or two-way ANOVA followed by Dunnett post-hoc; Results: Control patients presented the lowest bleeding time 50 sec, followed by AntiXa (98), SAPT (105), DTI (120), DAPT (190) and VKA (203). A statistically significant difference was present among control and DTI (p=0.004), VKA (p<0.001), DAPT (p<0.001). Conclusions: Based on the present outcomes, an increased risk of prolonged bleeding emerged in patients taking VKA and DAPT. However, bleeding did not interfere with the oral hygiene ses-sion The optimal period for dental treatment of these patients should be 2-3 hours before the next dose, without the need to temporarily suspend the medication.

The impact of the accurate estimated time of arrival (ETA) is often overlooked by bus operators. By providing accurate ETA to riders, it gives them the impression of bus services is efficient and reliable and this promotes higher ridership in the long run. This research project aims to predict bus arrival time by using the Support Vector Regression (SVR) model which is based on the same theory as the Support Vector Machine (SVM). Urban City Bus data covering part of the Petaling Jaya area (route name PJ03) is used in this research work. Features related to traffic such as travel duration, a distance of the road, weather and operation at peak or non-peak hour have been used as input in the training of the SVR model. By using kernel trick and specifying optimum parameters, all the features in higher dimensions are efficiently calculated and the SVR model achieves convergence. The model is evaluated with the test set of data split from the original dataset. The experimental result indicates the SVR model displays good prediction ability with its low average error on the prediction result. However, weather data has not been influential to the prediction model as the results of the model trained with and without weather data show a negligible difference.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

The relaxation process of lithium batteries caused by load variation is considered. It is shown that such processes have strong dependence on internal physical and chemical processes and battery technical conditions. Theoretical expressions of the relaxation process caused by a step-like load variation have been obtained for 1^st and 2^nd order equivalent electrical circuits. The experimental investigations show that the obtained models fit the real relaxation processes and the behavior of the identified parameters could be explained by specific features of physical and chemical processes within the lithium battery. It should be noted that the obtained results can be generalized for a different type of electrochemical power source. The proposed approach makes it possible to provide means for electrochemical power source characterization and diagnostic, the main advantages of which are good time localization of measurement procedures and inexpensive apparatus implementation.

This case report describes the successful repair of a radial bone fracture and skin defect in a dog using an ulnar bone graft and an advancement flap. A one-year-old spayed female Poodle dog weighing 1.7 kg was brought in with non-weight-bearing lameness, an open wound, and a frac-ture in the right forelimb. The dog had fallen off the bicycle being ridden by its owner, causing its right forelimb to be caught in the wheel. The treatment included surgical debridement of the necrotic tissue, skin reconstruction with an advancement flap, and radial bone reconstruction with an ulnar bone graft, bone morphogenetic protein (BMP), humeral cancellous bone and a ti-tanium T-shaped plate. Postoperative management included antibiotics, pain medication, and activity restriction. The dog made a good recovery and was able to bear weight on the affected limb four months after surgery.

Against the background of the sky, imaging and perception of aircraft are cru- cial. Among these, the location of aircrafts is not a very difficult problem in general, because that deep learning algorithms and object detection models based on convolutional neural network(CNN) are ever-evolving. In order to have a better identification of various aircrafts, or to accurately locate different types of flying targets in the sky, it becomes significant to distinguish and recognize different types of aircrafts. One question is that, distinguishing and recognizing between sub-categories of aircrafts pose great challenges. Although fine-grained recognition focuses on exploring and studying such problems, aircrafts under different sub-categories and granularities lead us to rethink the application of features. We noticed that features in swin-transformer demonstrates the under- standing and processing of images, fully showcasing the encoding and indexing of information. Through this research and proposed approach, we discovered a better understanding of features encoding and use, which are inspired by the feature encoding and computation in swin-transformer. In our paper, our ap- proach has achieved effects on features encoded graphically, manifested from the architecture design and convolutional neural network computation, and outper- forms other famous fine-graiend classification models on this issue. Not only approach we proposed has demonstrated superior performance in fine-grained aicraft classification, but also the mechanisms of the feature encoding under different sample space partitions is revealed for this issue, which provides a re- search for the representation of aircraft fineness characteristics. The relationship between representation orientation of aircraft feature information under various grained divisions, shows that the recognition of different categories according to man-made, such as aircraft, can be achieved by means of the feature represen- tations studied in this paper, for more specific defined classification tasks and various man-made targets partition criteria, which may influences the princi- ple of design for calculation and feature extraction in fine-grained classification models.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

The mutation in NF2 is the most common alteration associated with meningioma oncogenesis, and it is related to the loss of a suppressing protein called merlin. At the same time, alterations in energy production are visible in cancer cells where increased demand for energy is observed. Fatty acid oxidation could be one of the ways cancer cells obtain energy. This metabolic pathway uses the acylcarnitine shuttle system, which is responsible for the acylation of fatty acids and their transport through mitochondria. Therefore, this study aimed to profile acylcarnitines with short-, medium- and long-acyl chain length in meningiomas to assess their changes in tumors with different NF2 mutation statuses. For the analysis, solid-phase microextraction (SPME) coupled with liquid chromatography high resolution mass spectrometry (LC-HRMS) was used. The presented sampling method enables low invasive and easy collection of the analytes from the studied lesions, which can be crucial for future analysis of potential biomarkers in the surgery room. It was observed that higher levels of these analytes characterized meningiomas with NF2 mutation. Moreover, increased energy consumption and elevated levels of acylcarnitines show that these analytes can be considered as a marker of increased fatty acid oxidation in NF2 mutated cells.

In modern times, technology has become more than just a tool; it is a vital component of our lives, driving society and humanity towards new horizons, better living standards, and solu-tions for complex, global challenges. This article explores the world of dependable systems, specifically focusing on system design, software solutions, and architectural decisions that fa-cilitate collaborative work. It aims to dive into the intricacies of designing robust and effective document collaboration software. Throughout this paper, readers will gain insights into the proposed design process, enabling them to understand, learn from, and critically evaluate the examined methodologies and outcomes. Like everything else in the software technology field, there are multiple solutions to any given problem, and this work is no exception to this rule. The objective of this study is to provide a detailed architectural overview of the microservices pattern in an orchestrated cloud environment based on independent containers. To examine the pros and cons of such a system, the paper will detail how a real-time document collaboration system can benefit from such an architecture regarding availability, elasticity, scaling, and disaster recovery. Moreover, the paper will analyze how cloud-native technologies can be used to create a scalable platform solution, capable of handling traffic, dynamic resource storage, asynchronous com-munication, and application scaling. The intricate nature of this system renders this paper a valuable resource for prospective investigations within the domain of dependable systems, cloud computing, and distributed systems. This paper not only showcases the design and implementation process but also sets a founda-tion for future research and innovation in dependable systems, collaborative technologies, sustainable solutions, and distributed system architecture.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

Sharding shows great potential for extending the blockchain. The current challenge facing sharded blockchain technology lies in addressing the extended transaction confirmation times caused by isolated states between shards and unbalanced transaction allocation strategies. These factors contribute to an increase in cross-shard transactions and disproportionate shard workload, ultimately resulting in indefinite confirmation delays for cross-shard transactions. A critical priority for sharded blockchain systems is to conduct a comprehensive qualitative analysis to better understand and mitigate the prolonged transaction confirmation times. We introduce a Product-Form Queue Network (PFQN) model to address the transaction confirmation time problem in sharded blockchains and incorporate a new confirmation queue to more accurately simulate the actual transaction confirmation process in the blockchain. In addition, we provide a detailed quantitative analysis of the relationship between network load, consensus efficiency, and security in sharded blockchains, laying a theoretical foundation for achieving robustness and efficiency in sharded blockchains. This research not only contributes to addressing the scalability issues in sharded blockchains but also offers a new perspective for future research directions.

In this paper, we perform the neural cryptanalysis and comprehensively analyze five block ciphers, Data Encryption Standard (DES), Simplified DES (SDES), Advanced Encryption Standard (AES), Simplified AES (SAES), and SPECK. The vulnerability of the block ciphers is investigated in three different attacks, such as Encryption Emulation (EE), Plaintext Recovery (PR), Key Recovery (KR), and Ciphertext Classification (CC) attacks. For the plaintexts, randomly generated block-sized bit arrays and texts are used. The block ciphers apply different numbers of round functions in the encryption of the block-sized bit arrays, and they are investigated by using the deep learning models trained with different numbers of data in EE, PR, and KR attacks. Moreover, the block ciphers use two different text encryption methods, Word-based Text Encryption (WTE) and Sentence-based Text Encryption (STE), to encrypt the texts in various operation modes, and they are analyzed with deep learning models in EE, PR, and CC attacks. As a result, the block ciphers can be vulnerable to deep learning-based EE and PR attacks using a large amount of train data, and STE can improve the strength of the block ciphers, unlike WTE, which shows almost the same classification accuracy as the plaintexts, especially in CC attack. Additionally, when the keys that are the same as the plaintexts are used in encryption, the block ciphers can be perfectly broken in KR attack. Moreover, especially in KR attack, the RNN-based deep learning model shows higher average Bit Accuracy Probability (BAPavg) than the fully connected-based deep learning model, which is used more often in previous works of neural cryptanalysis. Furthermore, although the transformer-based deep learning model is a state-of-the-art model in Natural Language Processing (NLP), the RNN-based deep learning model is more suitable for CC attack and shows higher classification accuracy.

Fluidized beds are pivotal in the process industry and chemical engineering, with Computational Fluid Dynamics (CFD) playing a crucial role in their design and optimization. Challenges in CFD modeling stem from the scarcity or inconsistency of experimental data for validation, along with the uncertainties introduced by numerous parameters and assumptions across different CFD codes. This study navigates these complexities by comparing simulation results from the open-source MFIX and OpenFOAM, and the commercial ANSYS FLUENT, against experimental data. Utilizing a Eulerian-Eulerian framework and the kinetic theory of granular flow (KTGF), the investigation focuses on solid-phase properties through the classical drag laws of Gidaspow and Syamlal-O’Brien across varied parameters. Findings indicate that ANSYS Fluent, MFiX, and OpenFOAM can achieve reasonable agreement with experimental benchmarks, each showcasing distinct strengths and weaknesses. The study also emphasizes that both the Syamlal-O’Brien and Gidaspow drag models exhibit reasonable agreement with experimental benchmarks across the examined CFD codes, suggesting a moderated sensitivity to the choice of drag model. Moreover, the analysis were also carried out for 2D and 3D simulations, revealing that the dimensional approach impacts the predictive accuracy to a certain extent, with both models adapting well to the complexities of each simulation environment. The study highlights the significant influence of restitution coefficients on bed expansion due to their effect on particle-particle collisions, with a value of 0.9 deemed optimal for balancing simulation accuracy and computational efficiency. Conversely, the specularity coefficient, impacting particle-wall interactions, exhibits a more subtle effect on bed dynamics. This finding emphasizes the critical role of carefully choosing these coefficients to effectively simulate the nuanced behaviors of fluidized beds.

Objective: To determine the effect of sandblasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar Vivadent) were divided into a control group (CTR, no surface treatment) and four test groups of three specimens each: Pre-S-30, Pre-S-50, Pre-S-110 were sandblasted with 30µm SiO2, 50µm Al2O3 and 110µm Al2O3 particles respectively, before sintering, Post-S-30 was sandblasted with 30µm SiO2 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner and a pressable ceramic (IPS e.max ZirPress, Ivoclar Vivadent) were fired. Sixteen micro-bars were obtained from each block and submitted to the micro-tensile bond strength (µTBS) test. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Sandblasting before sintering with 110µm Al2O3 (Ra=3.44±0.44µm), 50µm Al2O3 (Ra=2.32±0.46µm), and 30µm SiO2 (Ra=1.22±0.22µm) resulted in significantly higher roughness than sandblasting after sintering with 30µm SiO2 (Ra=0.46±0.11µm). The highest µTBS was measured when the sintered zirconia was sandblasted with 30μm SiO2 (26.79±14.80 MPa), which was significantly different from that of specimens that were sandblasted before sintering (Pre-S-30=20.90±11.70; Pre-S-50=21.27±15.19; Pre-S-110=23.99±16.83) or were not treated (CTR=17.44±14.03). Conclusions: Sandblasting zirconia before sintering enhances the surface roughness proportionally to the particle size of the sand used. Sandblasting with 30µm SiO2 after sintering appeared to improve bonding between the veneering ceramic and zirconia. Clinical Significance: Sandblasting with 30µm SiO2 after sintering may improve bonding between veneering ceramics and zirconia, thus reducing ceramic fractures/chippings.

Background: Antibiotic resistance is an overwhelming serious difficulty globally. This necessitates the exploration of novel sources of antibiotics to overcome this challenge. Aim of the study: Bacterial Myxopyronin A production from various soil environments Egypt; as well as testing its antimicrobial activity in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Different soil environments in Egypt were screened for the growth of bacterial isolates producing Myxopyronin A as an antimicrobial agent. Purification of Myxopyronin A was performed via reversed-phase HPLC. Paper disc diffusion assay, as well as the Broth dilution technique, were exploited to assess the invitro antimicrobial and minimum inhibitory concentration( MIC) of the test antibiotic. Furthermore, in vivo antimicrobial spectrum, adverse drug reactions, and pharmacokinetics were detected during animal model testing stages and human randomized clinical trials phases 1/2. Results: From the culture supernatant of the Myxobacterium Myxococcus fulvus 124B02 which was the predominant soil bacterial isolate grown on the Casein yeast peptone plate, Myxopyronin A was produced. The test antibiotic blocked the growth of many Gram +ve bacteria with MICs less than 100 mcg/ ml. In contrast, it inhibited the growth of a few Gram -ve bacteria such as Escherichia coli at MICs greater than 100 mcg/ ml. On the other hand, Eukaryotic cells such as fungal and human cells were not affected. Prokaryotic DNA-dependant-RNA polymerase( RNLP) was noticed to be inhibited via the test antibiotic suggesting its bactericidal action. The maximum concentration was 7-8 mcg/ ml at a maximum time of 2 hours when 600 mg dose was orally administered in randomized human clinical trials phases 1/2, and T1/2 reached 2.5 hours following first-order kinetics of elimination. The duration of its action was nearly 12 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and cholestatic jaundice in less than 5 % of experimental candidates. Conclusion: The present study was promising due to the bactericidal antibiotic Myxopyronin A production from Myxococcus fulvus 124B02 isolated from different soil environments in Egypt.

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

BACKGROUND: Thromboembolic disorders including Myocardial infarction[ MI] and stroke represent the leading causes of death worldwide. Fibrinolytic enzymes extracted from microbial sources showed high efficacy in the dissolution of different blood clots. AIM OF THE STUDY: Screening and the bacterial recombinant DNA manufacture of bacterial fibrinolytic enzymes from different soil environments in Egypt. METHODOLOGY: A total of 50 soil samples were screened for their fibrinolytic enzyme production. The potent fibrinolytic enzyme-producing bacterial isolates were evaluated for their thrombolytic activities using the plasma plate method. The characterization of the enzyme activity and thermostability were carried out; also, the determination of molecular mass using a mass spectrometer and western blot technique was performed. The purification of the fibrinolytic enzymes was done through the affinity chromatography technique. On the other hand, the production of the purified bacterial fibrinolytic enzyme was achieved via bacterial recombinant DNA technology. Formulation of fibrinolytic enzymes in different dosage forms was tried. RESULTS: In the present study, the purified bacterial fibrinolytic enzyme was approximately 83% pure through affinity chromatography and SDS-PAGE assay. The predominating bacterial isolate secreting fibrinolytic enzymes was found to be Bacillus cereus. The fibrinolytic enzyme activities of 50 soil samples were found to be in the range of 0.167-1.853 U/ ml. The fibrinolytic activity of the extracellular enzyme refined from the culture supernatant of Bacillus cereus was relatively stable over the PH range from 7.4-10 for 18 hours and also it showed stability with the highest productivity at a temperature of 43 0C for nearly 60 minutes. The enzyme was called fibrin-proteinase[ FP] in the present study. The FP degraded the fibrin clots via direct thrombolysis. The specific activity and the molecular mass of the FP were estimated to be nearly 40.71 Units/ mg protein and nearly 30 KDa respectively. Protease activity was noticed to be slightly increased in the presence of Fe+3; While it was inhibited in the presence of EDTA. On the other hand, the FP fibrinolytic activity was enhanced greatly after the addition of monovalent cations such as K+1 and Na +1. The enzyme was also active over the temperature range of 20- 65 0C with the highest activity at 55 0C. The optimum temperature and PH of protease production was at 35-43 0C and PH 8.0-10. Conclusion: During the present study, the thermostable fibrinolytic enzyme FP purified from Bacillus cereus in different soil environments in Egypt was a promising fibrinolytic enzyme because it showed a broader efficacious fibrinolytic activity as well as less adverse effects than the current fibrinolytic enzymes globally. It is recommended in the future advanced exploration of the optimization of suitable formulation of bacterial fibrinolytic enzymes to aid in the dissolution of various blood clots and as a consequence overcoming the high rate of mortality globally.

Relationships of the three bryophyte lineages (liverworts, mosses, and hornworts) to vascular plants is a pivotal question in the study of origin and evolution of land plants. In recent decades, this question has been subject to intense phylogenetic analyses using morphological characters, multigene DNA sequences, and genome structural characters. A tentative consensus reached ten years ago suggested that bryophytes are a paraphyletic group, with liverworts being sister to all other land plants and hornworts being sister to vascular plants. However, several more recent nuclear phylogenomic studies have concluded that bryophytes represent a monophyletic group that is sister to vascular plants. A discussion is presented here on strengths and weaknesses of different types of characters (morphological traits, nucleotide sequences, and genome structural arrangements), and their suitability for resolving deep phylogenetic relationships. Moreover, several criteria for credible phylogenetic reconstruction are proposed. Strong statistical support for reconstructed relationships should be derived from high quality, independent characters selected for suitability to the particular question being addressed. The relationships inferred in a study should be congruent with those from as many other lines of phylogenetic evidence as possible. Any incongruities should be explicable by well-understood biological mechanisms. It is concluded that the relationships of the three bryophyte lineages to vascular plants should currently be viewed as unresolved. This is a difficult phylogenetic problem; the land plants underwent a rapid radiation a long time ago. Yet, further exploration of analytical methods and careful choice of characters should lead to eventual elucidation of diversification patterns among early land plants.

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

One of the most important agrotechnical factors that influence the growth conditions of crops is plant density. Alterations in habitat conditions result in the emergence of phytophagous organisms, whose development is closely associated with host plants. The objective of this study was to assess the abundance and species composition of thrips (Thysanoptera) collected in soybean plants of different varieties cultivated under different plant arrangements (row spacing, number of seeds sown differed). The research was conducted at two locations in southwestern Poland between 2015 and 2018. The herbivores that inhabit plants were caught using an entomological net. The experiments were carried out using the complete randomised block design, with four replications. Regardless of location and treatment, thrips were the most numerous group of pests. Thrips tabaci and T. fuscipes were the dominant species within the collected material. A total of 24 species of thrips were identified and their dietary specialisation was determined. The assemblages of studied insects were also analysed due to the density of the plants and the stage of development. The increase in the sowing density of soybean (90 seeds per m2) resulted in a greater total number of thrips compared to a lower sowing density (50 seeds per m2). The number of thrips significantly increased during the flowering period and shortly after the flowering time, which made them a significant threat to the plants. Therefore, it is crucial to develop innovative pest management strategies tailored to effectively grow soybean to mitigate potential pest-related challenges.

The International Maritime Organization (IMO) is enforcing increasingly stringent regulations on ship carbon emissions, The International Maritime Organization (IMO) has been implementing progressively strict regulations on ship carbon emissions, leading to the adoption of the virtual arrival (VA) method by many vessels to reduce their carbon footprint. However, the effectiveness of the traditional VA method often varies in busy ports with complex traffic organization scenarios. To address this, our study presents a novel, comprehensive model that integrates vessel scheduling with the VA approach. This model is designed to achieve a dual objective: reducing carbon emissions through Virtual Arrival and simultaneously minimizing vessel waiting times. In addition to these goals, it incorporates essential aspects of safety, efficiency, and fairness in port management, utilizing the NSGA-2 algorithm to find optimal solutions. This model has been tested and validated through a case study at Ningbo-Zhoushan port, employing its dataset. The results demonstrate that our innovative model and algorithm significantly outperform traditional scheduling methods, such as First-Come-First-Serve (FCFS) and Virtual-Arrival Last-Serve (VALS), particularly in terms of operational efficiency and reduction in vessel carbon emissions.

Alkaline and alkaline-thermal activation were used in an attempt to synthesize zeolites using the sedimented illite fraction of raw Devonian clays from the Kuprava clay pit in Latvia. The Si/Al molar ratio of these clays is 2.79. Thermal and hydrothermal treatments were conducted using 6M and 10M NaOH solutions, along with different curing environments. The treated samples were analyzed using XRD, FTIR, and SEM, and were compared to the raw and calcined illite fraction samples. The main phase that forms after alkaline treatment is hydrosodalite (Na8[AlSiO₄]₆(OH)₂∙2H₂O). Using a higher concentration of NaOH leads to a significant increase in hydrosodalite formation. Increasing the curing temperature from 120°C to 600°C slightly reduces hydrosodalite formation due to the crystallization of the nepheline (Na₃K(Al₄Si₄O₁₆)) phase. This phase forms relatively intensively when the chemically treated samples are cured in a nitrogen environment at 600°C, thereby reducing the formation of hydrosodalite. The characteristic layered-fused structure of clay minerals remains in all chemically treated samples when cured at 600°C in air, but it does not remain when cured at the same temperature in nitrogen. The intensive formation of hydrosodalite is mainly achieved through hydrothermal treatment, along with a primary treatment using 10M NaOH. Considering the calculated size of the crystallites, treatment with 6M NaOH and curing at 120°C can also be seen as beneficial for hydrosodalite formation.

Adeno-associated viruses (AAV) are widely used as viral vectors for gene delivery in mammalian cells. We focused on the efficacy of transduction of AAV 2/5, 2/6, 2/8 and 2/9 expressing GFP in 3T3-L1 murine preadipocyte cells by live imaging microscopy using IncuCyte S3 and flow cytom-etry. Three transduction modes were assessed: AAV transduction in 3T3-L1 preadipocyte cells with or without further differentiation into mature adipocyte-like cells and injection of AAVs in differ-entiated adipocyte-like cells. AAV2/6 demonstrated the highest transduction efficiency in 3T3-L1 preadipocytes, as it was 1.5–2-fold more effective than AAV2/5, and AAV2/8 in the range of viral concentrations from 2×104 to 1,6×105 VG/cell. AAV2/5 and AAV2/8 showed transduction effi-ciencies similar to each other. The expression of GFP under the CMV promoter remained stable for up to 20 days. The induction of 3T3-L1 differentiation in three days after AAV transduction did not alter the GFP expression level, and AAV2/6 showed the best transduction efficiency. AAV2/6 demonstrated the ability to transduce mature adipocytes. These results were confirmed by in vivo studies on C57BL6 mice AAV2/6 had the highest transducing activity on both inguinal and inter-scapular adipose tissue. Thus, AAV2/6 has demonstrated higher transduction efficacy compared to AAV2/5, AAV2/8 and AAV2/9 both in 3T3-L1 adipocytes and adipose tissue in vivo, which proves its usability along with AAV8 and AAV9 for gene delivery to adipocytes.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

Background and Objectives: The aim of this study was to determine the job-related and individual features that influence BS and depression levels among dentists working in faculties, oral and dental health centres (ODHC) and private clinics. Materials and Methods: This prospective, cross sectional study was carried out on dentists working in different regions of Turkey. Data were collected using an on-line questionnaire created using Google Forms. The questionnaire consisted of demographic data, Maslach BS Inventory (MBI) and Beck Depression Inventory (BDI) sections. Demographics were age, height, weight, marital status, blood type, gender, monthly income, income satisfaction and having enough free time. The dentists were divided into 3 groups as faculty, private clinic and ODHC according to the institutions in which they worked. Results: Of the total 290 dentists enrolled in the study, there were 172 males and 118 females with a mean age of 36.98±5.6 years. 128 of the dentists worked in faculties, 72 in private clinics and 90 in ODHCs. It was observed that women's EE scores were higher than men's (P<0.05). No statistically significant difference was found between the groups when comparing BS and depression scores according to marital status and blood group (P>0.05). There was no significant relationship between emotional exhaustion (EE), depersonalisation (DP), personal accomplishment (PA) and depression scores according to age, BMI and work experience, age, work experience and BMI (P<0.05). It was found that the EE scores of the dentists working in the faculty and private clinic were lower than those of the dentists working in the ODHC (P<0.05). Monthly income was associated with depression (r = -0.35). Conclusions: This study showed that dentists working in ODHCs had more EE. These findings suggest that there is a need for improvement in the working conditions of dentists, particularly in ODHCs.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In this paper, we consider the Cauchy problem of a time fractional nonlinear diffusion equation. According to the Kaplan’s first eigenvalue method, we first prove the blow-up of the solutions in finite time for some sufficient conditions. We next give sufficient conditions for the existence of global solutions by using the result of Zhang and Sun. In conclusions, we find the second critical exponent for the existence of global and non-global solutions via the decay rates of the initial data at spatial infinity.

Anaerobic digestion is a biological process that transforms high-strength organic effluents into biogas with multiple benefits. However, concurrent with organics' biological transformation, a liquid phase with a high solid content is also derived from this process. Valorizing this fraction is not an easy task if an agronomic application cannot be considered as a suitable option. The thermal valorization of this fraction allows for energy extraction, but also gives rise to additional capital investment and increases the energy demand of the global process. In addition, the thermal treatment of digestate has to deal with a mineralized material. The changes in organic matter due to anaerobic stabilization were studied in the present manuscript, by evaluating the thermal behavior of samples, activation energy and organic transformation using FTIR spectroscopy. Digested samples of a mixture composed of manure and glycerin (5% v/v) were studied. The stabilization caused a dramatic decrease in aliphatic compounds, greatly increasing the mineral content of the sample. Thermal valorization of digestates must consider the lower energy content and more complex structure of these materials, with higher content of lignin and protein-type compounds.

Unique analytical challenges arise when drivers, who face a route choice between a toll lane and a set of free lanes, have different values of time. The most complex situation is one in which multiple sub-populations of drivers exist, each with their own unique mean and coefficient of variation of value of time. This situation, when imbedded within a larger network cannot be tackled using existing planning models, and consequently is usually only approximated. This paper examines these different approximations, the resulting numerical solutions and the implications of these approximations on the estimate of the number of expected toll lane users. The paper also shows how this problem can be solved using a combined traffic assignment/simulation model. The first part of this paper develops an analytical formulation for solving the toll lane scenario using the “value of time” representations range from the simplest to the most complex. It is shown that one of the most critical issues is a determination of who the marginal users are of the toll lane, at each level of usage, as the perceived disutility of the last marginal toll lane user depends dynamically upon that driver’s value of time. Analytical formulations based on these different approximations are then solved numerically in the second part of the paper. These numerical solutions show that significant different lane use estimates result, depending upon the representation of value of time. Consequently, it is clear that solving this problem with the fewest approximations is both of theoretical and practical importance. The third part of the paper illustrates the solution to the toll lane problem, with each level of approximation, using a combined traffic assignment/simulation model. The simulated resulting estimates of the toll lane usage for each case matches both the relative and absolute trends found in analytical solutions. However, the solution using the assignment/simulation model is not only much faster and simpler to obtain, but is also scalable both in size and complexity. The additional complexities, that are associated with a less approximate representation of value of time, should therefore be incorporated in all future assessments of toll lane facilities, be they analyzed analytically or through simulation.

:. Background and Objectives: Pulmonary embolism, PE, incidence had been increasing in the last ten years. Computed thoracic pulmonary angiography, CTPA, had a major role in confirming PE di-agnosis.The main purpose of the study was to establish the prognostic value of a CTPA parameter: pulmonary artery obstruction index, PAOI, for PE risk assessment . A second objective of the re-search was to investigate the predictive accuracy of biomarkers (D-dimer, and cardiac Troponin T, c-TnT ), and PAOI, in 7-day mortality. The third objective of the study was the relationship between PAOI, and these biomarkers, in different etiologies of PE. Materials and Methods: The study com-prised 109 patients with PE, hospitalized, and treated between February 2021, and August 2022. They had different etiologies: deep vein thrombosis, DVT; persistent atrial fibrillation, AF; chronic obstructive pulmonary disease, COPD, exacerbation; Covid; and cancers. The investigations were the following: clinical examination; D-dimer testing, as a mandatory method for PE suspicion( values ≥ 500 µg/L were highly suggestive for PE); c-TnT , as a marker of myocardial injury(values ≥ 14 ng/L were abnormal); CTPA, with right ventricle dysfunction, RVD, signs, and PAOI. Treat-ments were according to PE risk: systemic thrombolysis (in high risk , and hemodynamic instability); low weight molecular heparins, LWMH, after systemic thrombolysis, or in high risk PE, with he-modynamic stability; direct oral anticoagulants, DOAC (in low, and intermediate risk). Results: The relationship PAOI- D-dimer, and PAOI- c-TnT, had very strong statistical correlation, for the entire sample, and for DVT, AF, COPD, Covid subgroups ( Rho = 0.815-0.982). PAOI had a high predic-tive accuracy for intermediate , and high risk together (area under curve, AUC=0.948), and high risk PE (AUC= 0.993). For 7-day mortality, D-dimer , and c-TnT had high predictive accura-cy(AUC=0.921, and 0.979). PAOI had statistical significance for 7-day mortality in Covid (p=0.045), and cancer (p=0.038) patients. Conclusions: PAOI was an important tool for PE risk as-sessment. D-dimer , and c-TnT were valuable predictors, for 7-day mortality in PE. PAOI, and D-dimer; PAOI, and c-TnT were strongly correlated, for the entire PE sample, and for DVT, AF, COPD, and Covid patients.

To compare and adjust activated clotting time (ACT) between two systems and to optimize ACT during atrial fibrillation (AF) ablation. Methods: Electromagnetic detection using a rotation tube (EM system; Hemochron Response, Soma Tech Intl, Bloomfield, CT, USA) and photo-optical detection using a cartridge immersed in blood (PO system; ACT CA-300TM, APEL) were compared. Results: The EM system showed an ACT of 320 ± 44 s (average ± 1 standard deviation), with a range of 156–487 s, from 3363 measurements in 1161 patients during uncomplicated procedures. An ACT >400 s was observed in 3.7% (124/3364) of patients. The pre-ablation ACT measured by the EM method was 143 ± 28 s. Cardiac tamponade was observed in 4/2085 ablations (0.19%) over 5 years. The ACT associated with cardiac tamponade ranged from 330 to 391 in the EM system. No thromboembolic or major bleeding complications were observed. Comparison of the two methods showed ACT-EM system = 1.19 × ACT-PO system + 9.03 (both regression coefficient and intercept, p<0.001, r = 0.90). In the Bland-Altman plots, the average difference between ACTEM and ACT-PO was 50 s. These differences increased with an increase in the average ACT value. This led to an adjustment of the recommended ACT target of 300–350 s for the EM system to 275–290 s for the PO system. Conclusions: The ACT obtained using the EM system aligned with the ACT recommended in the guidelines. However, the PO system showed significantly lower ACT values compared to those obtained with the electromagnetic system. This study clarifies that adjusting the optimal target ACT when switching between ACT measurement systems is essential.

Tack is one of the most important factors affecting the operability of prepregs, but it is still very difficult to obtain the change of prepreg tack with time at different temperatures. In this paper, a newly designed T-peel device is used to test the tack decay rate of prepregs at different temperatures. The obtained decay rate deviates less than 8.9% from the manufacturer's data. The maximum deviation of the ratio of tack decay speeds calculated by the Arrhenius equation from the experiments is not higher than -9.7%. It is proved that the present method can obtain the decay rate of tack of prepregs at different temperatures. This method is also applicable to the other two types of prepregs. The article proposes the handling life unit, an operational life measurement unit for prepregs, and establishes that the relationship between tack and remaining shelf life reduces prepreg management costs.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

The digital transformation in Industry 4.0 has revolutionized quality control paradigms, integrating advanced technologies such as augmented reality, deep learning, and computer vision systems into a new era called "Quality 4.0". This study systematically reviews how these technologies are shaping new practices in continuous quality supervision and improvement, adapting to increasingly automated and connected production environments. Through a comprehensive analysis of the literature, practical applications in various industrial sectors, from manufacturing and agriculture to the production of sweets and snacks, are highlighted. Additionally, the conceptual and detailed design of a quality control system using artificial intelligence tools is presented, focusing on the inspection of dimensions, color, weight, and labeling of MDF boxes. The proposed system demonstrates an effective integration of sensors, high-definition cameras, and deep learning algorithms, validated through tests with boxes of different sizes. The results suggest that the adoption of these technologies not only improves the accuracy and efficiency of inspections but is also essential to maintaining high-quality standards in a dynamic and competitive industrial environment.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

The term Air Quality (AQ) pertains to the standard of air, which has a direct impact on the health and well-being of individuals. It is crucial to maintain high Air Quality (AQ), for better health and productivity. Though most of people spend more time indoors nowadays, it is not to be overlooked that the pollutant concentration in indoor air is directly linked to the outdoor air quality. Due to the changes in occupancy patterns, outdated maintenance of ventilation systems, and structural flaws in buildings, the indoor air is significantly polluted; pollutants emitted outdoors enter indoor air through open windows, ventilation systems and infiltration. In this paper, we have proposed a new technique, DTMCPM (discrete-time Markov chain (DTMC) model for the analysis and forecasting of AQ, using the power method). Specialized sensors and equipment to measure different pollutants, such as particulate matter, ozone, nitrogen dioxide, sulfur dioxide, benzene and toluene, are used to collect data by the Institute of Pakistan Air Quality Monitor in various cities; the data is converted to US EPA standard for all pollutant species. This data is used to calculate the transition matrix, steady-state values and mean return rate for the analysis of IAQ. The calculated and actual return rates have been compared and the proposed model is found to have a low average prediction error of 2.356%.

In the last decades we have experienced great social, cultural, and educational changes, spending more time performing tasks in near vision and less hours in outdoor activities, having more overexposure to digital screens, especially the youngest and increasingly from younger ages. It is common to see cases when performing tasks in near vision the posture or position of the head is not adequate, especially the youngest, being essential to have a correct posture of the head to avoid visual, muscular, or articular problems. We present a procedure to try to control the correct position of the head in real time when performing close-up activities. The aim is to detect the inclination of the head and to know if a bad position is adopted due to a visual problem or simply to inadequate visio-postural habits, warning us of the postural anomaly to correct it.

Chip pad alignment inspection is of great importance in the industrial field. However, due to the fact that chip pads are usually small, problems such as misdetection and missed detection often occur. When applying deep learning methods for chip pad detection, it is necessary to ensure accurate detection of small target chips while meeting the requirements of lightweight detection models for industrial needs. To solve the above problems, this paper proposes a lightweight model based on improved YOLOv5s. Firstly, the feature extraction part is improved to increase the network's focus on the target. Secondly, the feature fusion layer is improved to double the resolution of the prediction head, and the context-aware network is designed to enhance the context-capture ability of key features of small targets. Finally, SIoU is adopted as the loss function to improve the speed and accuracy of the regression frame. The experimental results show that the improved YOLOv5s algorithm improves the detection accuracy by 2.3% and reduces the network parameters by 81.8% compared to the original algorithm. The improved algorithm is combined with image processing techniques to design correction methods for alignment anomalies and realize real-time alignment anomaly correction in industry.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Background/Objectives: Pityriasis rosea (PR) is a self-limiting exanthematous disease associated with the endogenous reactivation of human herpesvirus (HHV)-6 and HHV-7. Classically, the lesions gradually resolve leaving no sequelae. Therefore, the best treatment is reassuring the patient and suggesting a resting period. However, atypical PR cases characterized by extensive, persistent lesions and systemic symptoms may impact the patient’s quality of life, and, therefore, a treatment can be prescribed. There is limited evidence on the comparative effectiveness of pharmacological treatments for PR, therefore we performed a network meta-analysis to compare these interventions. Methods: Overall, 12 randomized control trials (RCTs) were identified. The outcomes were itch resolution and rash improvement. Results were expressed as risk ratio (RR) and 95% confidence interval (CI). We also calculated the relative ranking of the interventions for achieving the aforementioned outcomes as their surface under the cumulative ranking (SUCRA). Results: On network meta-analysis, only oral steroids and the combination of oral steroids+antihistamine resulted significantly superior to the placebo in terms of itch resolution (RR 0.44, CI 0.27-0.72 and RR 0.47, CI 0.22-0.99). Oral steroids resulted as the best treatment (SUCRA 0.90) for itch resolution. In terms of rash improvement, only acyclovir and erythromycin resulted significantly superior to placebo (RR 2.55, CI 1.81-3.58 and RR 1.69, CI 1.23-2.33), and acyclovir outperformed all the other tested interventions. Consequently, acyclovir ranked as the best intervention (SUCRA score 0.92). Conclusions: Acyclovir represents the best option in PR patients with extensive, persistent lesions or systemic symptoms. Steroids and antihistamines seemed the best treatment for itch resolution.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

Commuting is a vital travel channel for college students throughout their higher education career; nevertheless, excessive commute time negatively impacts students’ school satisfaction, academic achievement, health, and quality of life. Meanwhile, few studies have explored students’ commute time, covering a large population and scope. Therefore, this study analyzes the dwelling type that influences college and graduate students’ school commute times in the Seoul Metropolitan Area, using data from the 2016 Household Travel Diary Survey. This study uses spatial data on housing development to classify five dwelling types (i.e., new town, housing site development, Seoul, Incheon, and Gyeonggi-do). A multiple linear regression model empirically analyses students’ household and personal characteristics. The results reveal that dwelling type significantly affects students’ commute time. Specifically, Students living in Seoul have a shorter commute to school than those living in new towns. Socioeconomic characteristics have less effect on college and graduate students' school commute time. This study discusses the problem of excessive commuting of college and graduate students in new towns.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

Accurate traffic simulation models play a crucial role in developing intelligent transport systems that offer timely traffic information to users and efficient traffic management. However, calibrating these models to represent real-world traffic conditions accurately poses a significant challenge due to the dynamic nature of traffic flow and the limitations of traditional calibration methods. This article introduces a machine learning-based approach to calibrate macroscopic traffic simulation models using real-time traffic video stream data. By leveraging computer vision technologies to extract key traffic parameters from video streams, the approach demonstrated a notable improvement in aligning the generated data from the calibrated simulation model with car sensor data, achieving an average improvement of over 50% compared to the uncalibrated macroscopic model. Moreover, there was a substantial reduction in data drift for the machine learning model integrated into the virtual transport space using vehicle-to-everything technology, resulting in a more than fourfold decrease in the average absolute error of the model.

The extent of correlation or co-movement among the returns of developed and/or emerging stock markets remains pivotal for efficiently diversifying global portfolios. This correlation is prone to variation over time as a consequence of escalating economic interdependence fostered by international trade and financial markets. In this study, we analyzed the time-varying correlation and co-movement between the JSE.JO stock market of South Africa and its developed and developing stock market partners. The Dynamic Conditional Correlation - Exponential Generalized Autoregressive Conditional Heteroscedasticity (DCC-EGARCH) methodology is employed with different multivariate distributions to explore the time-varying correlation and volatilities between the JSE.JO stock market and its partners. Based on the conditional correlation results, the JSE.JO stock market is integrated and co-moves with its partners, and the conditional correlation for all markets exhibit time-variant behavior. The conditional volatility results show that the JSE.JO stock market behaves differently from other markets, especially after 2015, indicating a positive sign for investors to diversify between JSE.JO and its partners. The highest value of conditional volatility for markets was in 2020 during the COVID-19 pandemic, representing the riskiest period that investors should avoid due to the lack of diversification opportunities during crises.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

The aim of the present trial was to evaluate the growth performance of buffalo calves fed diets characterized by different forage/concentrate ratio with or without the Saccharomyces Cerevisiae supplementation (CBS 493.94, Yea-Sacc®). Twenty-four male buffalo calves (mean age 145.1 ± 16.1 days; mean weight 108.0 ± 18.7) were assigned randomly to 4 groups, homogeneous for age, fed four different diets: diet 1 F:C ratio 50:50; diet 2 F:C ratio 30:70; diet 3 F:C ratio 50:50 + Yea-Sacc® and diet 4 F:C ratio 30:70 + Yea-Sacc®. Buffalo calves were individually weighted before the start of the experiment and the data were used as a covariate, monthly until the end of the trial. Dry matter intake (DMI), daily weight gain (DWG) and feed conversion ratio (FCR) were calculated. The differences in diets’ composition significantly (p

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

The Mara River basin (MRB) has a world-famous ecosystem, but the vegetation has been damaged due to economic development in recent years, and there is little known about the area that will experience severe vegetation damage in the future. Based on the vegetation vulnerability system, principal component analysis, and three CMIP6 scenarios (SSP1-2.6, SSP2-4.5, SSP5-8.5), vegetation vulnerability was calculated in the base period (2010-2019), near-term period (2020-2059) and long-term period (2060-2099) in the MRB. The spatial cluster of vegetation vulnerability was revealed by spatial correlation analysis, and the transition of vegetation vulnerability of different periods was analyzed by stochastic matrix. The results showed that in all periods, the vulnerability showed a high-high cluster in the east, and a low-low cluster midstream and downstream. From the stochastic matrix, the area of high vulnerability increased the least under the SSP1-2.6, while it increased the most under the SSP5-8.5. The vegetation vulnerability upstream increased the most from the base period to the near-term period and long-term period in the MRB. By comparing the vegetation vulnerability under different scenarios, and pointing out the areas with the highest vulnerability increase, this study can better provide comprehensive decision-making for vegetation protection in the MRB.

In forests, the microbial populations living in the soil can directly affect the carbon decomposed by the surface plants, and promote carbon storage and stability. In this study, 3 plots of 25.82 m×25.82 m were set up in 5 stand types, respectively. Soil samples were collected from 0~20 cm, 20~40 cm and 40~60 cm layers. Soil microbial composition, organic carbon component, pH, water content, bulk density, nitrogen, phosphorus, potassium and other physicochemical indexes and correlations were determined, and the correlations between soil carbon components and soil microbial functional modules in different mixed modes were analyzed. The results showed that: (1) The SOC of the same soil layer varied significantly, which also showed significant differences on the composition of soil bacteria and fungal microbial communities. Moreover, the bacterial community was more sensitive to the vegetation change environment, and the fungal community structure was more resistant to the influence of soil environment changes. (2) Fun_mod 1,6 and Bac_mod 7 were the microbial functional modules that played a decisive role in the process of soil carbon pool change, and the diversity and composition of bacterial community had more positive effects on soil organic carbon than that of fungal community. (3) Linear fitting and RDA results showed that POC in soil had the strongest correlation with SOC content, indicating that soil microorganisms affected the storage and stability of soil carbon mainly by regulating the conversion of surface plants (carbon sources) into POC. The soil environment of different mixed modes has different effects on soil carbon accumulation. Soil microorganisms affect soil carbon storage and stability mainly by regulating the conversion of surface plants (carbon sources) into POC forms.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

This bibliometric analysis delves into the realm of botanical gardens through the process of mapping literature and discerning research frontiers, underlying themes, and interconnections within the extant body of knowledge. The study uses a dataset of 1340 publications and employs methodologies such as authors' keywords co-occurrence data to examine the discipline's trends, patterns, and knowledge gaps. The study finds significant growth in literature from 1960 to 2023, emphasizing botanical gardens, conservation, taxonomy, biodiversity, ex-situ conservation, and diversity. Key influencers such as Sanja Kovačić, Elaissi, and Chemli have steered research directions towards ex-situ conservation and essential oils, reflecting the field's interdisciplinary nature. The study shows global institutional variation, with entities like the Chinese Academy of Sciences, the Royal Botanic Gardens UK, and the New York Botanical Garden US leading the discourse. Thematic analyses have identified core themes and emerging research topics, with ecological restoration, essential oils, invasive species, and climate change mirroring the field's expanding scope. The consistent prevalence of themes such as 'botanical gardens' and 'conservation' over time underscores their enduring significance. Emerging topics like climate change and biodiversity are gaining prominence, signaling a shift in research priorities. The expanding array of subjects, including 'invasive species' and 'genetic diversity,' indicates an amplified scope and growing complexity in botanical garden research. This study aims to bridge a crucial gap by outlining the developmental trajectory of botanical gardens and offering guidance for future research directions. Diverse research domains within botanical garden studies, including biodiversity, essential oils, taxonomy, and ex-situ conservation, present extensive avenues for exploration. Future research endeavors should delve into these impactful themes to better understand botanical ecosystems and their conservation. The study emphasizes the importance of nurturing interdisciplinary collaborations and multidisciplinary projects, advocating for a comprehensive and collaborative approach to future research in botanical garden studies.

In this paper, a proof similar to the Pusey-Barrett-Rudolph (PBR) theorem is given to prove that time in quantum theory is not epistemic but has ontological reality. For this, we first discuss how time can be encoded as an intrinsic property of a quantum system. We prepare a quantum state containing time as an intrinsic property and show by a PBR-type proof that time cannot be an epistemic notion. In fact, the PBR theorem implies an ontic notion of time. Indeed, if the quantum state is a physical property, then quantum state reduction is a physical process involving information destruction. In this case, quantum probabilities are intrinsic probabilities without epistemic origin, and they generate a genuinely new sequence of events. This novelty introduced by quantum probabilities can be interpreted as time.

Climbing is an Olympic discipline in full development and multidisciplinary in nature, in which the influence of body composition and nutritional status on performance has not yet been clarified despite the quest for low weight in anti-gravity disciplines such as climbing. The present study aimed to do a nutritional (3-day dietary diaries) and body composition (ISAK profile) assessment of sport climbing athletes of different genders and sport levels. The mean age of the forty-six Spanish climbers (22 men and 24 women) was 30 years (SD: 9) with 7.66 years of experience (SD: 6.63). The mean somatotype of the athletes was classified as balanced mesomorph. Negative correlations were observed between fat mass variables and climbing level (p<0.01), and positive correlations with forearm circumference (p<0.05). Mean energy availability (EA) was 33.01 kcal-kg FFM1-d1 (SD: 9.02), with 55.6% of athletes in suboptimal EA status and 35.6% in low energy availability (LEA) status. Carbohydrate and protein intakes were below recommendations in 57.8% and 31.1% of athletes, respectively. There were deficient intakes of all micronutrients except phosphorus in males. These findings suggest that climbing athletes are at high risk of developing low energy availability states and concomitant problems. Optimal nutritional monitoring may be advisable in this type of athlete to try to reduce the risk of LEA.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

In the realm of physical activity and sports science, motion tracking emerges as an important tool for specialists aiming to analyze movement data, whether for daily life activities or enhancing athletic performance. This study introduces an innovative approach to motion tracking through the development of a fully embedded smart shoe sensor system, which employs an inertial measurement unit (IMU) affixed to the shoe sole, coupled with six pressure sensors, to provide real-time calculation of individual stride lengths along with other vital movement statistics. Traditional motion tracking methods, which typically rely on various body-attached sensors, often necessitate substantial post-processing, delaying the feedback loop. In contrast, our system is designed to overcome these limitations by offering high-accuracy, real-time feedback with a minimal error rate of 1.88% from our experiments. Such prompt data acquisition facilitates immediate interventions by sports performance coaches or healthcare professionals, significantly contributing to injury prevention and performance enhancement. The experimental outcomes of this study underscore the system’s capability to deliver precise stride length measurements instantaneously, marking a significant advancement in motion tracking technology and its application in sports science and healthcare.

Real-time object detection remains a pivotal topic in the realm of computer vision. Balancing the accuracy and speed of object detectors poses a formidable challenge for both academic researchers and industry practitioners. While recent transformer-based models have showncase the prowess of the attention mechanism, delivering remarkable performance improvements over CNNs, their computational demands can hinder their effectiveness in real-time detection tasks. In this paper, we elect to use YOLOX as our robust starting point and introduce a series of effective enhancements, culminating in a new high-performance detector named YOLOAX. To further exploit the power of the attention mechanism, we devise multi-dimensional attention-based modules that activate CNNs, emphasizing the most pertinent regions and bolstering the capacity to learn the most informative image representations from feature maps. Moreover, we introduce a novel leading label assignment strategy called STA, along with a groundbreaking loss function named GEIOU Loss, to further refine our detector's performance. We provide extensive ablation studies on the COCO and PASCAL VOC 2012 detection datasets to validate our proposed methods. Remarkably, our YOLOAX is trained solely on the MS-COCO dataset from scratch, without leveraging any prior knowledge, which achieves an impressive 54.2% AP on the COCO 2017 test set while maintaining a real-time speed of 72.3 fps, surpassing YOLOX by a significant margin of 3.0% AP. Our source code and pre-trained models are openly accessible at https://github.com/KejianXu/yoloax.

The study´s goals were to determine the health status of a group of heart transplant recipients (HTR) and their level of physical activity and to compare the health status among them and with a group of healthy sedentary individuals. Fifty-four HTR and eighteen S were assigned to four groups, according to their level of physical activity (determined with The International Physical Activity Questionnaire); patients with a low, a moderate and a high level of physical activity (HTRL, HTRM and HTRH, respectively) and sedentary individuals (S). Participants underwent a basic blood analysis and several tests to assess their cardiovascular, neuromuscular, functional mobility condition and their quality of life. The S and HTRH were very similar in terms of BP, HR and blood analysis while HTRM and HTRL differed from both S and HTRH in these parameters. Regarding the cardiovascular, neuromuscular, functional mobility, and quality of life variables assessed in this study, HTRH showed the best results across all of them, followed by S, HTRM, and HTRL. It is suggested that the weekly level of physical activity of HTR should be high, what might help them to enhance their health and quality of life.

Background: Breast cancer and other neoplasms, such as acute lymphocytic leukaemia, are a severe hazard to public health globally. L-glutamine-degrading enzymes are required for the treatment of malignancies such as acute lymphocytic leukemia and breast cancer. L-glutaminase, an amidohydrolase, has been shown to be an effective chemotherapeutic tool for treating a variety of malignancies. The aim of the study: Molecular characterization is used in the study and production of bacterial L- glutaminase as an anticancer agent from a variety of Egyptian soil locales. The type of the study: Screening experimental study. Methodology: In the current study, many bacterial isolates were tested on mineral L-glutamine agar selective medium (MGA) to evaluate if they generated L-glutaminase. The most effective positive bacterial isolates that produce L-glutaminase, however, were discovered by morphological and biochemical analysis. The primary positive isolate producing L-glutaminase was also identified utilizing molecular detection by 16S rRNA sequencing homology technique. The properties of bacteria-produced L- glutaminase were investigated. The anticancer activity was assessed with an MTT assay. Results: Sole bacterial isolates that only needed L-glutamine for metabolic nitrogen grew well on MGA. The optimal conditions for producing positive bacterial isolates were pH 7.4 and 37 ̊C. The morphological and biochemical investigations of soil samples from diverse soil conditions in Egypt revealed that Bacillus subtilis subsp. niger (ATCC 9372) was the primary positive bacterial isolate producing L-glutaminase. At a pH of 7.4 and a temperature of 37 °C, the activators KCL, ZnSO4, FeSO4, K2HPO4, and MgSO4 offered ideal conditions for defining L-glutaminase production. L-glutaminase from Bacillus subtilis was detected to be a highly bioavailable and efficient anticancer treatment. The original yield [productivity] from MGA was 6.3 U/ml, but invitro coupled transcription and translation production raised it to 89± 1 U/ml. L-glutaminase had a molecular mass of approximately 36 kDa. The purification of L-glutaminase resulted total activity of 21,883 ± 15.67 (U), specific activity of 379.14 ± 7.35 (U/mg of protein), and purification fold of 1.82 ± 3.06. The enzymatic activators Ni2+ and Mg 2+ increased L-glutaminase activity by 20%, 27%, respectively. The compound showed significant anticancer activity (IC50 = 38.72, 8.6, 6.41, 19.02, 49.83, and 9.45 μg/ml) against cancer cell lines from the liver (HepG-2), colon (HCT- 116), breast (MCF-7), lung (A-549), lymphocytic (CCL-120), and cervical (Hela). The kinetic parameters Km and Vmax were 15.2^ 10 -3 M and 119.86 μmol/ml/min, indicating a higher affinity for the substrate. The enzyme demonstrated high efficacy at pH 6.5 and temperature 35. The enzyme was thermostable at 58 ̊C for 1 hour. Conclusion: Acute lymphocytic leukemia and breast cancer are two instances of auxotrophic malignancies for which L-glutamine is the sole metabolic source, and Bacillus subtilis- derived L-glutaminase was a suitable enzyme in their treatment.

Background: The World Health Organization identifies lung and prostatic cancers as solid tumors with significant global lethality, both being auxotrophic cancers for L-arginine aminoacid. The aim of the study: The study aims to detect L-arginase-expressing bacteria from various soil environments in Egypt using 16S rRNA and characterize its anticancer activity. Methodology: A hundred samples of Egyptian grassland soil were gathered at a depth of 11–20 cm, close to wheat mills. Using fast plate assay screening and spectrophotometric analysis, the presence of bacteria generating L-arginase was verified. The major soil bacterial isolates were identified by morphological characterization, biochemical responses, and 16SrRNA sequencing methods. The anticancer activity of the test enzyme was assessed using MTT assay. Results: On the MAA medium, only the bacterial isolates capable of using L-arginine as the only metabolic source for carbon and nitrogen were cultivated. Bacillus cereus DSM 360 was shown to be the prevailing bacterial isolate generating L-arginase using molecular detection and biochemical reactions. When Co+2, Ni+2, and Mn+2 metal ions were present as co-factors, bacterial L-arginase demonstrated remarkable anticancer action against auxotrophic tumors for L-arginine. The total protein content was 0.349 mg, while total enzyme activity was 8.174 U with 61% enzyme recovery. As well as the specific activity reached 23.4212 U/mg. Using the mass spectrometer, the molecular weight of the bacterial L-arginase was revealed to be 37 KDa. The bacterial L-arginase's IC50 values were 3.12 U/ml for the lung cancer cell line, 3.91 U/ml for prostatic cancer cell line, 0.91 U/ml for acute promyelocytic leukemia cancer cell line and 2.73 U/ml for kidney cancer cell line. The enzyme under test showed kinetic characteristics of 7.36 mmol/l and 6.14 μmol/min for Km and Vmax, respectively. The half-life time (T1/2) was 90.17 min at 50°С, while being 86.53 min at 60°С. The test enzyme was thermostable at 60°С for 1 hour. Conclusion: The study showed a potential strategy by identifying and determining a newly discovered bacterial L-arginase enzyme as an anticancer agent in Egypt's soil settings.

We are using the book “Towards Quantum Gravity with an article by Claus Kiefer as to a quantum gravity interpretation of the density matrix in the early universe. The density matrix we are using is a one loop approximation, with inflaton value and potential terms, like V(phi) using the Padmanabhan values one can expect if the scale factor is a ~ a(Initial) times t ^ gamma , from early times . In doing so, we isolate out presuming a very small initial time step candidates initial time values which are from a polynomial for time values due to the Kiefer Density value.

Fall armyworm, Spodoptera frugiperda, is one of the major migratory polyphagous insect pests of various crops. The essential nutrient and mineral profile of host plants determines the feeding fitness of herbivorous insects. As a result, growth and development of insects is affected. To determine the effect of nutrient and mineral profile of different host plants (maize, castor bean, cotton, cabbage, okra and sugarcane) on the growth and development of S. frugiperda, biological parameters like larval weight, pupal weight (male/female), feeding and growth indices were calculated. The proximate compositions and mineral contents of the tested host plants showed a significant difference (p&lt;0.5). Better nutrients were observed in castor bean and maize host plants. The growth indices on these host plants also showed the statistical difference (p&lt;0.05) except efficiency of ingested food (p&gt;0.05). The maximum relative growth rate (RGR), relative consumption rate (RCR) and consumption index (CI) were recorded in S. frugiperda larvae that fed on maize and castor bean leaves. Larval, male and female pupal weights were the maximum in the larvae feeding on castor bean host plant. In case of fitness indices, the highest larval growth, pupal growth, standard growth and fitness indices were observed in S. frugiperda larvae that fed on maize. The findings of the present study highlight the dynamic growth and development of S. frugiperda larvae on maize plants and provide novel information based on nutritional ecology to develop sustainable integrated pest management strategies using selective crop rotation and limiting alternative host plants.

Honey is a natural product that, thanks to its composition, particularly the high sugar content, is highly appreciated as an energy nourishment. In addition to sugars, it contains many other substances (carbohydrates, free amino acids, enzymatic proteins, organic acids, polyphenols) from which the therapeutic properties of honey arise: hydrating and osmotic activity, antimicrobial action, antioxidant and anti-inflammatory power. The present work aims to deepen the activity of skin protection exerted by honey, as a synergic result of its multiple therapeutic effects.Moreover, the study want to find possible correlations between biological properties and chemical-physical traits of honey. To carry out this research, five varieties of citrus honey, one of acacia honey, one of chestnut honey and, finally, one of multifloral honey were used. The honeys were first characterized by chemical-physical analysis (determination of water content, sugars, amino acids, polyphenols) and then subjected to qualitative melissopalynological analysis. Tests were also carried out to evaluate both their antioxidant power and the effect on collagenase, an enzyme involved in the degradation of collagen present in the extracellular matrix and, therefore, in the processes of skin aging. Finally, they were used in in vitro experiments to assess their action in stimulating cell viability and proliferation on human keratinocytes.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

Proper Post-Activation Performance Enhancement helps to improve athletic performance. This study aimed to investigate the effects of two different velocity loss (VL), 10%VL and 20%VL, on post-activation performance enhancement (PAPE) in 20m sprint performance among sprint athletes. Twenty-four male sprint athletes (100m sprint time: 10.96±0.15 s) were recruited. A randomized crossover experimental design was used for traditional group (TG), 10%VL, and 20%VL interventions. Sprint tests were conducted at the 4th, 8th, 12th, and 16th minutes after the intervention. Two-way repeated measures ANOVA revealed an interaction effect between group and time on 20m sprint performance (F=2.817, p=0.037, partial η²=0.585). Simple effect analyses showed significant differences compared to baseline at the 4th minute for the 20%VL group (P&lt;0.05). Cohen's d values indicated improvement in 10m sprint times at the 8th minute of the rest interval for all three intervention groups (TG: ES=-0.270, 10%VL: ES=-0.038, 20%VL: ES=-0.279). Improvement in 20m sprint times was observed at the 4th minute for the 20%VL group (ES=-0.296) and at the 16th minute for the 10%VL group (ES=-0.276). Compared to traditional PAPE schemes based on 1RM, PAPE schemes based on velocity loss (20%VL) can better induce PAPE effects in sprint athletes.

Hormone changes across women's menstrual cycle may lead to changes in perception of chemical signals and hormonal responses to these cues. The aim of the present study was to determine the role of menstrual cycle phase on the effects of extracts of male axillary secretions (EMAS) in women. We tested healthy reproductive age and premenopausal women (n=29). EMAS/control solution was applied once in two hours either in the follicular or luteal phase, while collecting saliva samples for LH and cortisol monitoring. LH and cortisol concentrations were analyzed using EIA technique. PANAS and VAS were used to assess the mood. We observed a significant increase in the number of LH peaks (p=0.0447) and their amplitude (p=0.0469) when EMAS was applied in the follicular phase. The same application in the luteal phase lowered the amplitude of LH peaks (p=0.0382). EMAS application increases salivary cortisol level in reproductive age women relative to premenopausal women (p=0.0032). PANAS revealed changes in positive and negative affect after EMAS application. Our data indicate the significance of the menstrual cycle phase for EMAS effects on LH secretion, mood, but not on cortisol secretion in women.

Venous and arterial thromboembolism (VTE/ATE) often coexist with onco-hematologic diagnosis. The study aimed to assess the time relationship between the diagnosis of VTE/ATE and blood cancers. The second aim was to identify VTE/ATE risk factors related to the type of hematology disease and cardiac history. 1283 patients underwent cardio-oncology evaluation at the Institute of Hematology and Transfusion Medicine in Warsaw from March 2021 through March 2023 (2 years), and 101 (7.8%) cases were identified with VTE/ATE. ATE compared to VTE significantly more often occurred before the diagnosis and treatment of hematologic malignancy: 33/47 (70.2%) vs. 15/54 (27.8%), p<0.0001. The risk of a VTE episode is exceptionally high in the first months after the diagnosis of an onco-hematological disease. The higher frequency of VTE was associated with acute myeloid leukemia (17 cases/270 patients/6.30%/p = 0.055), acute lymphocytic leukemia (7 cases/76 patients/9.21%/p = 0.025) and chronic myeloproliferative disease (7 cases/48 patients/14.58%/p=0.0003). Only the risk of VTE was significantly increased before (OR=6.79; 95%CI: 1.85-24.95; p=0.004) and after diagnosis of myeloproliferative disease (OR=3.12; 95%CI: 1.06-9.16; p=0.04). ATEs occur more often than VTE before a diagnosis of blood cancer. The risk of VTE is exceptionally high before and after diagnosis of chronic myeloproliferative disease.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

In the present study, we aimed to observed hair follicle development and describe Wnt10b/β-catenin signaling pathways related to hair follicle development in different ages of Rex rabbits. Six Rex rabbits (3 male and 3 female) of 15, 30, 60, 90, 120 and 150 days of age were selected and skin samples were collected for hair follicle development and Wnt/β-catenin signaling pathway genes expresion detection. The results showed that the the values for body weight, coat length, skin thickness, skin area, and skin weight of Rex rabbits were increased significantly with age (p &lt; 0.05). The total hair follicle density, secondary hair follicle density and the ratio of the secondary hair follicle density to the primary hair follicle density in 120 days of Rex rabbits was higher than that in the other ages (p &lt; 0.05), and the major hair follicles were in the growing period at 15 days and 30 days of age, some of them had already entered the degeneration period at 60 days of age, and most of them entered the degeneration period at 90 days of age, the presence of quiescent hair follicles and the enlargement of primary hair follicles were also observed. At 120 and 150 days of age, the back hair follicles entered the growing period, and the secondary hair follicles had obvious differentiation. Furthermore, the expression of the Wnt10b, CTNNB1, adenomatosis polyposis protein (APC), Disheveled 2 (DVL2), glycogen synthase kinase 3β（GSK-3β）, Lymphoid enhancer-binding factor 1 (LEF1), dickkopf-1 (DKK1) and transforming growth factor beta 1 (TGFβ-1) genes in the skin tissue of Rex rabbits at different age was significantly differences (p &lt; 0.05), and the expression of the Wnt10b, CTNNB1, DVL2, GSK-3β, and TGFβ-1 genes at 90 days was higher than that in the other days, the expression of the LEF1 and DKK1 genes at 60 days was higher than that in the other days. As western blotting indicated, the β-catenin protein phosphorylation (P-CTNNB1) levels in the skin tissue of Rex rabbits shows the trend of first increasing, then decreasing and then increasing, 60 days, 120 days and 150 days significantly higher than 15 days, 30 days or 90 days (p &lt; 0.05). With the increasing of ages, the GSK-3β protein phosphorylation (P-GSK-3β) levels in the skin tissue of Rex rabbits were increasing, and maximum at 120 days of age (p &lt; 0.05). These results show that ages could influence on the fur quality and hair follicle traits of Rex rabbits, and Wnt10b/β-catenin signaling pathways is involved in the biological process of periodic hair follicle development in Rex rabbits. Considering the rule of fur growth, the slaughter age of Rex rabbits should not be earlier than 120 days.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Immune checkpoint inhibitors (ICIs), including anti-programmed cell death 1 ligand 1 (PD-L1) antibodies, are significantly changing treatment strategies for human malignant diseases including oral cancer. Cancer cells usually escape from immune system and acquire proliferative capacity and invasive/metastatic potential. We have focused on the two immune checkpoints, PD-1/PD-L1 and CD47/SIRPα in the tumor microenvironment of oral squamous cell carcinoma (OSCC), and performed a retrospective analysis of the expression of seven immune-related factors (PD-L1, PD-1, CD4, CD8, CD47, CD56 and CD11c), and examined their correlation with clinicopathological status. As a result, there were no significant findings relating seven immune-related factors and several clinicopathological statuses. However, the immune-checkpoint related factors (PD-1, PD-L1, CD47) were highly expressed in non-keratinized epithelium-originated tumors when compared to those in keratinized epithelium-originated tumors. It is of interest that immunoediting via immune checkpoint-related factors was facilitated in non-keratinized sites. Several researchers reported that keratinization of oral mucosal epithelia affected the immune response, but our present finding is the first study to show a difference of the tumor immunity in the originating-epithelium of OSCC, keratinized or non-keratinized. Tumor immunity, an immune escape status of OSCC might be different in the originating-epithelium, keratinized or non-keratinized.

The shear stress generated by wall turbulence is the main cause of wall friction resistance in turbulent flow through pipes. This paper investigates the impact of inserting rest periods (regions of constant Reynolds number) within the pulsating operating cycle of velocity on the fully turbulent flow at large time-averaged Reynolds numbers, using the Large Eddy Simulation (LES) method. The study aims to explore the effect of increasing rest periods within pulsations on drag resistance. The dimensionless shear stress and drag reduction rates during different time periods of rest were analyzed. Numerical simulation results indicate that the pulsating velocity operation mode does not necessarily lead to drag reduction; it may even result in increased resistance. Inserting rest periods within the pulsation cycle can achieve drag reduction effects, with the maximum drag reduction rate reaching 21.8\%. Comparisons with experimental data and Direct Numerical Simulation (DNS) from the literature validate the feasibility of using the LES method for pipe pulsating operation modes.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Background: Across the world, antibiotic resistance is a grave problem. To address this issue, it is necessary to investigate new antibiotic sources. Aim of the study: Egypt's diverse soil habitats were used to produce bacterial Myxopyronin B, which was then tested for antimicrobial activity in preclinical animal studies and randomized human clinical trials stages 1/2. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were examined for the development of bacterial isolates that produced the antibiotic compound Myxopyronin B. Reversed phase HPLC was used to purify Myxopyronin B. To determine the test antibiotic's minimum inhibitory concentration( MIC) and invitro antibacterial activity, the Broth microdilution method and the Paper disc diffusion assay were utilized. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in preclinical animal testing stages and phases 1/2 of randomized clinical studies involving volunteer humans. Results: Myxopyronin B was generated from the culture supernatant of Myxococcus SDU36, the main soil bacterial isolate cultured on a Casein yeast peptone plate. With MICs less than 100 mcg/ml, the test antibiotic prevented the growth of several Gram +ve bacteria, whereas, at MICs higher than 100 mcg/ml, it inhibited the development of a small number of Gram -ve bacteria, including Escherichia coli. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. The test antibiotic was seen to inhibit prokaryotic DNA-dependent RNA polymerase( RNLP), indicating its bactericidal activity. Mean Cmax was 9-10 mcg/ ml at mean Tmax 1 hour when 600 mg dose was orally administered in randomized human clinical trials phases 1/2, and T1/2 reached 2.25 hours following first-order kinetics of elimination. Duration of its action was nearly 8 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and GI upset in less than 7 % of experimental candidates. It exhibited approximately 90% plasma protein binding, especially with albumin which resulted in prolonged therapeutic action. It showed a concentration dependant antibiotic killing effect. With the concentration-dependent killing pattern, the higher the drug concentration relative to the pathogen minimum inhibitory concentration( MIC), the greater the rate and extent of antimicrobial activity. Conclusion: The present study was promising due to the production of the bactericidal antibiotic Myxopyronin B from Myxococcus sp. SDU36 isolated from different soil environments in Egypt.

Green manure could improve soil nutrients and crop production, playing a significant role in sustainable agriculture. However, the impacts of green manure on crop health and the roles soil microbial communities play in the process haven’t been clarified clearly yet. In this study, we investigated soil microbial community composition and structure in four tobacco farmlands, which were treated with different green manure (control, ryegrass, pea and rape), using 16S rRNA gene amplicons sequencing. Results showed that green manure had significant impacts on soil properties, microbial communities and tobacco health. First, soil total C, N and Ca content increased significantly in groups treated with green manure than control. Second, soil community diversity was significantly higher in groups treated with green manure. Third, green manure especially ryegrass, decreased tobacco disease (bacterial wilt) rate dramatically, and the process might be mediated by soil microbial communities. On the one hand, several microbial populations were found to be potentially disease inducible or suppressive. For example, the abundances of Dokdonella and Rhodanobacter were positively correlated to tobacco disease rate, while Acidobacteira_Gp4 and Gp6 had negative correlations with tobacco disease. On the other hand, soil microbial communities were shaped by soil properties (e.g., pH, C and N content). In conclusion, our research showed that green manure could increase soil nutrients directly, and further improve tobacco health mediated by soil microorganisms, which may shed light on revealing interactions among soil properties, microorganisms and plants.

Background: Antibiotic resistance is an overwhelming serious difficulty globally. This necessitates the exploration of novel sources of antibiotics to overcome this challenge. Aim of the study: Bacterial Myxopyronin A production from various soil environments Egypt; as well as testing its antimicrobial activity in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Different soil environments in Egypt were screened for the growth of bacterial isolates producing Myxopyronin A as an antimicrobial agent. Purification of Myxopyronin A was performed via reversed-phase HPLC. Paper disc diffusion assay, as well as broth dilution technique, were exploited to assess the invitro antimicrobial and minimum inhibitory concentration( MIC) of the test antibiotic. Furthermore, in vivo antimicrobial spectrum, adverse drug reactions, and pharmacokinetics were detected during animal model testing stages and human randomized clinical trials phases 1/2. Results: From the culture supernatant of the Myxobacterium Myxococcus fulvus 124B02 which was the predominant soil bacterial isolate grown on the Casein yeast peptone plate, Myxopyronin A was produced. The test antibiotic blocked the growth of many Gram +ve bacteria with MICs less than 100 mcg/ ml; whereas it inhibited the growth of a few Gram -ve bacteria such as Escherichia coli at MICs greater than 100 mcg/ ml. On the other hand, Eukaryotic cells such as fungal and human cells were not affected. Prokaryotic DNA-dependant-RNA polymerase( RNLP) was noticed to be inhibited via the test antibiotic suggesting its bactericidal action. Cmax was 7-8 mcg/ ml at Tmax 2 hours when 600 mg dose was orally administered in randomized human clinical trials phases 1/2; as well as T1/2 reached 2.5 hours following first-order kinetics of elimination. The duration of its action was nearly 12 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and cholestatic jaundice in less than 5 % of experimental candidates. Conclusion: The present study was promising due to the production of the bactericidal antibiotic Myxopyronin A from Myxococcus fulvus 124B02 isolated from different soil environments in Egypt.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

Based on PVDF (piezoelectric sensing techniques), this paper attempts to study the propagation law of shock waves in brittle materials during the process of three-wavelength laser irradiation of polysilicon, and discusses the formation mechanism of thermal shock failure. The experimental results show that the vapor pressure effect and the plasma pressure effect in the process of pulsed laser irradiation lead to the splashing of high temperature and high density melt. With the decrease of the laser wavelength, the laser breakdown threshold decreases and the shock wave is weakened. Because of pressure effect of the laser shock, the brittle fracture zone is at the edge of the irradiated area. The surface tension gradient and surface shear wave caused by the surface wave are the result of coherent coupling between optical and thermodynamics. The average propagation velocity of laser shock wave in polysilicon is 8.47×103m/s, and the experiment has reached the conclusion that the laser shock wave pressure peak exponentially distributes attenuation in the polysilicon.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

PET imaging of bacterial infection could potentially provide added benefit for patient care by non-invasive means. [68Ga]Ga-desferrioxamine B – a radiolabelled siderophore – shows specific uptake by human-pathogenic bacteria like Staphylococcus aureus or Pseudomonas aeruginosa as well as sufficient serum stability for clinical application. Here, we provide data for automated production of [68Ga]Ga-desferrioxamine B on two different cassette based synthesis modules (Modular-Lab PharmTracer and GRP 3V) using commercially available cassettes together with an approved 68Ge/68Ga radionuclide generator. Quality control including determination of radiochemical purity as well as a system suitability test was set up via RP-HPLC on a C18 column. The two described production processes, using an acetic acid/acetate buffer system with ascorbic acid as a radiation scavenger for radiolabelling, yield ready-to-use formulations with sufficient activity yield. Batch data showed radiochemical purity of &gt;95 % as determined by RP-HPLC and ITLC as well as excellent stability over 2 hours post production. Specifications for routine production were set up and validated with four master batches for each synthesis module. Based on this study, an academic clinical trial for imaging of bacterial infection was initiated. Both described synthesis methods enable reproducible, automated in-house production of [68Ga]Ga-desferrioxamine B for clinical application.

Although researchers have proposed various indentation size effect (ISE) models, these models often involve different form and number of parameters that can make our wonder which is the best in existed ISE models. Three types of ISE test data, namely, normal ISE, reverse ISE and transition of normal to reverse ISE, are used to evaluate the sixteen ISE models. The comparatively study indicates that H-J, N-G-Fs, N-G-H, N-G-A and N-G-Qs models can accurately predict the normal ISE. The reason for this is that the friction stress that is not related to dislocation activities or the indentation size effect of plastic zone has been introduced into these models. Therefore, these two factors should be considered in future ISE models. The sixteen ISE models are originally proposed to describe the normal ISE of different materials. However, to our surprise, some of these models are able to capture the reverse ISE and the transition of normal to reverse ISE of different materials. The determination coefficients (DC) of the sixteen ISE models are also determined for different materials. For reverse ISE, the highest DC value for NiCSi, TC4 and PED Ni are given by the EXP, N-G-Fs and N-G-A models, respectively. For the transition of normal to reverse ISE, the N-G-YC, N-G-Fs, and N-G-H models produce the maximum DC for ZrO2, Cu and Y2O3-ZrO2, respectively. Moreover, the mean DC of the N-G-Fs model is the maximum among the sixteen ISE models, followed by the N-G-H model, but they cannot accurately predict the reverse ISE. Therefore, the N-G-Fs and N-G-H models should be further modified to accurately predict the reverse ISE.

This paper addresses the evolving landscape of electricity markets in Europe, with a focus on the integration of Renewable Energy Communities as introduced by the Renewable Energy Directive 2018/2001. Residents within a postal code area are highly incentivized to join a community, which enables them to exchange energy among themselves at lower procurement costs. Thereby, energy management systems optimize the operation of respective energy systems, with electrical load forecasting playing a key role. Given that prosumers may switch between communities on a daily basis, electricity demands within these groups will vary, leading to data that is non-stationary, discontinuous as well as non-identical and independently distributed. To encounter this issue, we propose a sophisticated forecasting model that applies federated learning, using informations from various distributed communities to learn domain-invariant features. To achieve this, we initially utilize synthetic electrical load time series at district level and aggregate them to profiles of Renewable Energy Communities with dynamic portfolios. Subsequently, we develop a forecasting model that accounts for the composition of residents of a Renewable Energy Community, adapt data pre-processing in accordance with the time series process, and detail a federated learning algorithm that incorporates weight averaging and data sharing. Following the training of various experimental setups, we ultimately evaluate their effectiveness. The findings suggest that our proposed framework is capable of effectively forecast non-stationary and discontinuous time series and that it can be applied to new, unseen data through the integration of knowledge from multiple sources.

Coastal environments are complex systems that are influenced by a combination of natural processes and human activities. Scientific interest in the effects of coastal erosion/accretion and climatic change-related processes greatly increased in recent decades due to the growing human development along coastal areas. This paper investigates the state and evolution of beach-dune systems for the 1977-2001 and 2001-2019 periods of the Mediterranean coast of Andalusia (Spain) using two different proxies: the dune toe line, which was used to track foredunes evolution, and the high-water line, which was used to assess shoreline evolution. Results showed a general erosional behavior of the studied beach-dune systems and identified cases where the main trend was altered through human interventions. In the 1977-2001 period, 54% of foredunes showed erosion, 24% accretion and 22% stability while and 34% of shorelines showed erosion, 40% accretion and 34% stability. In the 2001-2019 period, 42% of foredunes showed erosion, 28% accretion and 30% stability, and 40% of shorelines showed erosion, 34% accretion and 26% stability. Combining the evolution classes of each proxy (dune toe/shoreline) allows the behavior of both shoreline proxies to be assed together and provides insights additional to those derive from the use of a single proxy. In this regard, Erosion/Erosion (EE) was the most frequent behavior, with 25% and 27% in the first and second periods respectively, and Accretion/Accretion (AA), with 17% in both periods. Erosion of foredunes combined with stability or accretion of the shoreline (ES and EA) were the most common pairings in the first period, while stability of dunes combined with accretion of the shoreline (SA) and Stability/Stability (SS) dominated in the second period. The results obtained provide additional insights on the nature and drivers of coastal change that aid local coastal managers and administrations in understanding erosion processes. The method can be applied at other areas around the world where a similar data base is available.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

In modern data analysis, working with diverse dataset formats is essential for ensuring compatibility across different software tools and platforms. However, manual conversion between formats can be time-consuming and error-prone. To address this challenge, we developed an interactive Shiny application that facilitates the seamless conversion of datasets between popular software formats such as CSV, Excel, SAS, SPSS, Stata, and RData. This user-friendly app enables users to upload datasets, select an output format, and download the converted file with a single click. The application also incorporates a real-time progress indicator, enhancing the user experience by showing conversion progress. Built with simplicity and efficiency in mind, the app is designed for researchers, data analysts, and practitioners who regularly handle multiple file formats in their workflows. Additionally, the app features a clean, intuitive interface with clear guidance, making it accessible even to users with minimal technical background. The development process, key features, and potential applications of this tool are discussed in this article.

There are several forms of maintenance high-efficiency hemodialysis (HD) including hemodiafiltrations (HDF) in different technic modes and expanded HD using dialyzers with medium cut-off membranes. The aim of the study was to assess the intradialytic tolerance and length of dialysis recovery time (DRT) in these modalities. This is an exploratory, cross-over study in maintenance HD patients with low comorbidity and no clinical indications for the use of high-efficiency HD, who were exposed to five intermittent dialysis in random order: high flux hemodialysis (S-HD), expanded HD (HDx), pre-dilution HDF (PRE-HDF), mix-dilution HDF (MIX-HDF) and post-dilution HDF (POST-HDF). 24 dialysis sessions of each method were included in the analysis. Dialysis parameters including blood flow rate, dialysis fluid flow rate and temperature, and pharmacological treatment were constant. Average total convection volume for post-HDF, pre-HDF and mix-HDF were 25.6 (3.8), 61.5 (7.2) and 47.1 (11.4) l, respectively. During all therapies, patients had similar hydration status monitored using bioimpedance spectroscopy and similar variability over time in systemic blood pressure, cardiac output, and peripheral resistance monitored using impedance cardiography. The lowest frequency of all intradialytic adverse events were observed during HDx. Delayed DRT was the shortest during PRE-HDF. Patients were also more likely to report immediate recovery while receiving PRE-HDF. These differences did not reach statistical significance, however the study results suggest that, intradialytic tolerance and DRT may depend on the dialysis method used. This support the need of taking into account patient preferences and quality of life while individualizing high efficiency therapy in HD patients.

Academics in healthcare grapple with the challenge of efficiently managing time while addressing diverse roles and responsibilities, leading to heightened levels of anxiety and stress within the academic community. The primary objective of this study is to offer a sustainable and systemic solution to the prevalent time-management challenges in healthcare academia, through the development of a predictive model. Employing systemic analysis software and adopting a systemic management approach, we crafted a model to address academic time-management concerns. The dynamics of time allocation for academicians are governed by three fundamental pillars: teaching, research, and administrative tasks. Significantly prioritizing administrative tasks depletes valuable academic time, making time management within academia excessively costly. This occurs as highly skilled individuals find themselves diverted towards administrative duties at the expense of their academic roles diminishing resilience levels. The proposed Timebooster Academic Systemic Model (TASM) advocates for the cultivation of soft skills in academia, en-compassing prioritization, seeking assistance, and addressing tendencies of perfectionism and procrastination. Additionally, TASM recommends the implementation of full automation, delegation of administrative responsibilities, and the mitigation of both overt and covert time-consuming elements. Furthermore, TASM reports on the pivotal role of the academic resilient manager-leaders, who actively contribute to their own satisfaction and academic growth by enhancing collaboration and teamwork. Time-management challenges emerge as a critical determinant of academic well-being and resilience. Systemic models, exemplified by TASM, offer a valuable framework for investigating prioritization concerns, identifying administrative impediments in academic processes, and managing low-value time-consuming elements. The TASM model, along with the systemic philosophy underpinning its design, presents an avenue for advancing the exploration of time-management phenomena within the context of healthcare academia.

Digital photogrammetry has attracted widespread attention in the field of geotechnical and geological survey due to its low-cost, ease of use and contactless mode. In this work, with the purpose of studying the progressive block surficial detachments of a landslide we developed a monitoring system based on fixed multi-view time-lapse cameras. Thanks to a new-developed photogrammetric algorithm based on the comparison of photo sequences through a structural similarity metric and the computation of the disparity map of two convergent views we can quickly detect the occurrence of collapse events, determine their location and calculate the collapse volume. With the field data obtained at the Perarolo landslide site (Belluno Province, Italy), we have preliminary tested the effectiveness of the algorithm and its accuracy in the volume calculation. The method of quickly and automatically obtaining collapse information proposed in this paper can extend the potentials of landslide monitoring system based on videos or photo sequence and it will be of great significance for further research on the link between the frequency of collapse events and the driving factors.

The environment significantly impacts the life of bees and their feeding. This study aimed to investigate bee foraging using melissopalynological analysis and DNA metabarcoding in ​​intensive farming, reserved, and urbanized areas. The highest alpha diversity was observed in the reserved and in the intensive farming areas. The urbanized area has less diversity. In the intensive farming area predominated: Sinapis, Helianthus, and Fagopyrum; in the reserved area: Melilotus, Helianthus, and Brassica. In the urbanized area garden plants: radish (Raphanus sativus) and cucumber (Cucumis hystrix) and agricultural plants: soybean (Glycine max) and melon (Cucumis melo) were often found. The most significant agreement was between the rbcL and the melissopalynological analysis. The ITS2 revealed equal matches with both rbcL and melissopalynology but this marker missed or underestimated some genera. Trifolium pretense and Brassica nigra, were identified simultaneously by three analyses. Species Convolvulus arvensis, Melilotus officinalis, Echium vulgare, Brassica rapa, Helianthus divaricatus, and Onobrychis viciifolia were found in all ecological areas. Imperfect databases put some limits for identification of some taxa using metabarcoding. Further research and expansion of plant databases is needed. Studying the food preferences of bees in different environmental conditions and landscapes is necessary to develop measures to preserve their population.