Neuroblastoma is the most common tumour in children under 1 year old, accounting for approximately 50% of infant cancer cases. Although current treatments are relatively efficacious against this cancer, associated adverse effects could be detrimental to growth and development. In contrast, glioblastoma accounts for 52% of brain tumours and has an extremely poor prognosis. Current chemotherapeutics include temozolomide, which has numerous negative side-effects and a low-effective rate. Previous studies have shown the manipulation of autophagy to be a promising method for targeting cancers, including glioblastoma. We sought to determine the effects of autophagic alterations in combination with current chemotherapies in both neuroblastoma and glioblastoma. Supplementing cisplatin or temozolomide with autophagy activator rapamycin stabilized cancer cell mitochondria, despite having little effect on apoptosis or oxidative stress. Autophagy inhibition via 3-methyladenine or hydroxychloroquine alongside standard chemotherapies enhanced apoptosis and oxidative stress, with 3-methyladenine also disrupting mitochondrial health. Importantly, combining hydroxychloroquine with 0.5 µM cisplatin or 50 µg/mL temozolomide was as or more effective than 2 µM cisplatin or 100 µg/mL temozolomide alone. Analyzing these interesting results, a combined treatment of autophagy inhibitor with a standard chemotherapeutic agent could help to improve patient prognosis and reduce chemotherapy doses and their associated side-effects.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

Nickel base superalloy GH4169 is a material with strong mechanical properties and is difficult to process. In order to reduce tool wear during material processing and improve workpiece surface processing quality, based on the finite element simulation software DEFORM, the influence of n, ap, and fz parameters on tool wear during carbide tool milling GH4169 was studied, and a simulation orthogonal experimental model was established, The prediction model of tool wear is obtained; The ultrasonic vibration milling is compared with ordinary milling, and the improvement degree of different coating materials on carbide tool wear is explored. The results show that the ultrasonic vibration signal is helpful to reduce tool wear, improve the surface quality of the workpiece, and improve the stability of the milling process. TIALN/TIN (WC) composite coated tools have good cutting performance, help to reduce tool temperature, reduce tool wear, and improve tool life.

Light alloys machining is a widely implemented process that have usually used in presence of cutting fluids to reduce the wear impact and increase tool life. However, current environmental protection policies require their elimination in order to improve process sustainability. This fact forces to work under aggressive cutting conditions, producing adhesion wear that affects the integrity of the part surface. This study describes cutting tool wear mechanisms in machining of UNS A92024 samples under dry cutting conditions. EDS analysis showed the different composition of the adhered layers, while roughness was also positively affected by the change of the cutting geometry produced in the tool.

Face milling is a well known commercial process highly used in heavy industries that consumes high amount of power. Besides power issue, modern manufacturing industries are aiming for per part cost reduction keeping the product quality unimpaired. Unexpectedly if the part is rejected in any stage of manufacturing, the cost of manufacturing dramatically increases. Major cause of part rejection is excessive tool wear that imparts poor surface profile or catastrophic tool failure that causes adherence of broken tool debris onto machined surface. Furthermore, the tool wear is associated with sliding distance (frictional distance) and the tool life quantifies the cost of tools. As such, from the perspective of manufacturing industries it is imperative to optimize the surface quality parameter, cost of part, power consumption, and material removal – this is exactly what is accomplished here. By this work, it is possible to conserve power consumption, produce parts with lower cost, manufacture with uncompromising surface quality and enhanced material removal rate. Moreover, as intermediate factors of interest, the influences of sliding distance, tool life and tool flank wear on the overall machining performance are evaluated. The multi-objective optimization by Grey Relational Analysis (GRA) revealed that for improved product performance and fast manufacturing (case 1) optimum results are: feed per tooth fz = 0.25 mm/tooth, cutting speed vc = 392.6 m/min and cutting length l = 0.5 mm; for resource conservation (case 2) the optimum results are: feed per tooth fz = 0.125 mm/tooth, cutting speed vc = 392.6 m/min, cutting length l = 0.5 mm.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

Aloe vera is well known for its biological properties as a bioflavonoid-anti-inflammatory, antibacterial agent. It has been used frequently in the food sector as food coating for its hygroscopic properties and as an ingredient in the lucrative industry. Studies have also included Aloe vera as an eco-friendly green solution based on these properties. The current research focuses on the use of Aloe vera gel in printing pastes as an alternative sustainable solution to synthetic thickeners, evaluating its wet performance and ease of fabric stitching, and has been inspired by studies that similarly used this substance measuring its effect on the fabric's coefficient of friction and antimicrobial action. In the current study, printing pastes with natural colourants and Aloe vera gel thickener derived from natural leaves from Crete increased the fabric's mechanical resistance to abrasion compared to the untreated pastes. The measured performance did not differ substantially from prints with traditional synthetic pastes, hence tolerating the substitution with the non-contaminant variant. The enhanced resistance to abrasion and wear prolongates the fabric's serviceable life and resulting garments, decreasing the need for high industry processing volumes and, as a result, reducing pollution. The resistance to wear was evaluated using the dominant method in textile testing of the Martindale apparatus, which measured the cycles to failure, weight loss, and general appearance deterioration using the official photographic standards.

This study explored the effects of cryogenic treatment on the microstructure, hardness, and wear-resistance of diamond-like carbon (DLC) by cryogenically treating NAK 80 mold steel coated with DLC. Raman spectroscopy analyzed the structure of the DLC film. Nanoindenter analyzed the hardness and Young’s modulus of the film, and their relationship determined the wear resistance. Wear test assessed the wear rate and friction coefficient of the DLC film. The results showed that cryogenic treatment increased the rate of carbide precipitation and refined the grain structure. Raman spectroscopy indicated that the Raman intensity rate (I_D/I_G) of treated DLC films was smaller than those without cryogenic treatment. When the sp3 bond increased, the hardness and wear-resistance of the DLC film also increased.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

Bandsaw blades are typical band-shaped cutting tools characterized by low stiffness and micro-level cutting depth, resulting in distinct wear mechanisms compared to rigid cutting tools. In this study, the wear curve and wear mechanisms of bandsaw tooth during the bandsawing of Cr12MoV cold-working steel was investigated. The tool life was divided into two stages: a rapid wear stage (Stage I) and a homogeneous wear stage (Stage II). In Stage I, the wear was dominated by chipping although multiple wear mechanisms were found due to the relatively poor manufacturing accuracy compared to rigid cutting tools, which results in remarkable differences among the cutting depths of individual teeth. In Stage II, abrasive and adhesive wear were the primary wear mechanisms instead of chipping, which was related to the microstructure of Cr12MoV. Furthermore, methods for increasing the bandsaw performance were proposed based on the tooth wear mechanisms.

The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. The tests were conducted for three sandstone varieties: Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching, however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities, as well as that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives.

The paper presents theoretical notions with practical applications for establishing of one dental bur lifetime (durability and reliability based on the active part wear considering a series of statistical indicators. For the justification application of theoretical notions in practice, a conical-cylindrical dental bur was studied experimentally, to obtain a series of data in the work process, necessary for statistical calculation. The parameter taken into consideration in this paper is mass lost through the dental bur active part wear, tested. This is useful for the dental bur lifetime establishment and its extension or even optimization in operation. The loss of mass of the dental bur active part is analyzed in the work process by the results and experimental data obtained and validated by a numerical calculation statistical-mathematical. The numerical calculation approximates very well the mass lost through the wear at different rotation speeds and operation times, with those experimentally determined ones, based on which it was established lifetime. The results showed that the dental bur works with high yield in the first 20 hours of work, , after which it should be replaced with a new one.

Optimizing input parameters not only improves production efficiency and processing quality but also plays a crucial role in the development of green manufacturing engineering practices. The aim of the present study is to conduct a comparative evaluation at cutting performance and machinability process during the turning of AISI 4340 steel under different cooling conditions. The study analyses cutting operations during turning using dry, minimum quantity lubrication (MQL), and nano-MQL. As control parameters in the experiments, three different cooling types, cutting speed (100, 150, 200 m/min), and feed rate (0.1, 0.15, 0.20 mm/rev) levels were applied. The experiment results present that the optimal output values are found as Vb=0.15 mm, Ra=0.81µm, 88.1 dB for sound intensity, and I=4.18 A for current. Moreover, variance analysis (ANOVA) was performed to determine the effects of input parameters on response values. Under dry, MQL, and nano-MQL processing conditions, parameters affecting tool wear, surface roughness, current by the motor shaft, and sound level were examined in detail, along with the chip morphology. The responses obtained were optimized according to the Taguchi S/N method. As a result of optimization, it was concluded that the optimum values for cutting conditions (A3B1C1) were nano-MQL cooling and V=100 m/min, f=0.1 mm/rev cutting. Last but not least, it was observed that there was a 13% improvement in tool wear, 7% in current, 9% in surface roughness, and 8% in sound intensity compared to the standard conditions. In conclusion, it was determined that nano-MQL and the lowest level of cutting and feed rate values provided the optimum results.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

Governments worldwide are actively committed to achieving their carbon emission reduction targets, and one avenue under exploration is harnessing the potential of hydrogen. Blending hydrogen with natural gas is emerging as a promising strategy to reduce carbon emissions, as it burns cleanly without emitting carbon dioxide. This blending could significantly contribute to emissions reduction in both residential and commercial settings. However, a critical challenge associated with this approach is the potential for Hydrogen Embrittlement (HE), a phenomenon wherein the mechanical properties of pipe steels degrade due to the infiltration of hydrogen atoms into the metal lattice structure. This can result in sudden and sever failures when the steel is subjected to mechanical stress. To effectively implement hydrogen-natural gas blending, it is imperative to gain a comprehensive understanding of how hydrogen affects the integrity of pipe steel. This necessitates the development of robust experimental methodologies capable of monitoring the presence and impact of hydrogen within the microstructures of steel. Key techniques employed for this assessment include microscopic observation, hydrogen permeation tests, and tensile and fatigue testing. In this study, samples from two distinct types of pipeline steels used in the natural gas distribution network underwent rigorous examination. To induce hydrogen absorption, an electrochemical charging process is employed in a solution rich in H+ ions. This charging process, accomplished by a potentiostat applying a constant current, prompts the hydrogen evolution reaction at the steel specimen, acting as the cathode of the charging cell. Immediate tensile and fatigue testing following the charging process enables the evaluation of mechanical properties in comparison to non-charged samples. Different charging current densities are employed to simulate various hydrogen blend scenarios. The findings from this research indicate that charged samples exhibit a discernible decline in fatigue and tensile properties. This deterioration is attributed to embrittlement and reduced ductility stemming from the infiltration of hydrogen into the steel matrix. The extent of degradation in fatigue properties is correlated not only to the hydrogen content but also to the hydrogen permeability and diffusion rate influenced by steel’s microstructural features, with higher charging current densities indicating a more significant presence of hydrogen in the natural gas pipeline blend.

Effective oral care is important to maintain a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using bioelectric effect (BE) with those of mechanical electric toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

The growing interest in benchtop NMR systems is visible in a vast number of applications in science and industry. Low-field nuclear magnetic resonance (LF-NMR) became an instant in technologies that productions are dependent on the reliable structure identification, grade and purity control, chemical process inspection or reaction monitoring. Beyond the benefits of being cost-, space-, maintenance- and user friendly, insufficient sensitivity and low signal resolution are the main drawbacks, due to which the low-field NMR (LF-NMR) in the fields of organic chemistry and synthesis remains limited to solely academic teaching purposes. Herein, we discuss the possibilities of LF-NMR for the needs of organic chemistry and synthesis on a set of compounds 1-4 achieved as the products of student’s laboratory course and organic derivatives 5-8 that are from our research interests. Chemical structure determination of all compounds 1-8 presented herein was performed using the benchtop-type NMR instrument operating at 60 MHz (Pulsar Oxford Ltd.). Structure of novel compounds 5-7 prepared under the aims of our research was characterized by combined 1H/19LF-NMR and compared with an appropriate high-field NMR data from Bruker Ascend Instrument (400 MHz). Finally, possibilities of the low-field NMR as an analytical tool for the research purposes in the fields of organic chemistry and synthesis are documented on a set of 1H and 2D 1H-1H COSY for azomethine 8.

Objectives: Evaluate the performance of diagnostic measures (sensitivity and specificity) of the intrinsic capacity (IC) construct recommended by the WHO ICOPE guidelines by domain and by age group. Study design: This cross-sectional study included 164 community-dwelling elderly (95 women and 69 men). The participants completed the assessment of the 5 domains of IC (cognition, psychological, vitality, locomotion and sensory). In addition, they were assessed for activities of daily living (ADL), instrumental activities of daily living (IADL), frailty and urinary incontinence. Main outcomes measures: Descriptive statistics were used to summarize the intrinsic capacity and identify which domains were compromised. Comparisons between three or more samples were made by 1-way ANOVA with Bonferroni post-test and those with two samples by the t-test or Mann-Whitney test for quantitative variables. Chi-square test was used for qualitative variables. The sensitivity and specificity of each domain and each domain by age group were evaluated using the ROC curve. Results: Participants with a decline in IC were older, worse ADL, IADL and mental function, low gait speed, and higher depression scores. In addition, people with a decline in IC had frailty, urinary incontinence. Other issues related to the decline in CI were self-reported non-practice of physical activities and level of schooling.The evaluation of each domain did not prove to be a good screening tool (sensitivity or specificity < 80%, but both values > 50%). When the analyses were separated by domain and age group, good performance was found in the psychological (69-69 years and ≥80 years), vitality (≥80 years) and sensory (≥80 years) domains. Conclusions: The ICOPE screening tool performed well in terms of diagnostic measures when applied by domain and age group.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

To increase the power density of the electromechanical drive train of wind turbines, journal bearings can be used as planetary gear bearings instead of rolling bearings. This technological change presents new challenges. For example, wind turbine drive systems are subject to dynamic and low-speed operating conditions which can lead to an accelerated abrasive wear of the journal bearings. In addition, oil supply failure or peak loads due to wind gusts and grid and power converter faults could potentially result in catastrophic failure due to adhesive wear in a very short time. Such operating characteristics are, therefore, critical regarding the journal bearing wear lifetime and must be considered in the design. The successful implementation of journal bearings in wind turbines depends on a reliable estimation of adhesive and abrasive wear. In this paper, five different models for the wear calculation of journal bearings are evaluated regarding their suitability of wear calculation of planetary gear bearings in wind turbines. For this purpose, the following evaluation criteria were defined: parameter uncertainty, parametrization effort, in particular number of parameters, parameterization method and load case dependency of parameters and calculation effort. In order to be able to evaluate the wear models, the wear models are numerically implemented and the wear of a test journal bearing is exemplarily calculated under load conditions, which are comparable to load conditions in a wind turbine. Relevant influences from the wind turbine system such as lubricant, material and manufacturing dependent surface influences like roughness and hardness are considered. The wear models are evaluated with respect to their fulfillment of the defined criteria. The resulting evaluation allows the selection of a wear model that can be used to calculate the wear of planetary gear journal bearings in wind turbines, considering the available input variables.

This study investigates the diversity and evolution of research topics within the dental sciences from 1994 to 2023 using topic modeling and Shannon's entropy as a measure of research diversity. We analyzed a dataset of 412036 scientific articles across six dental disciplines: Orthodontics, Pros-thodontics, Periodontics, Implant Dentistry, Oral Surgery, and Restorative Dentistry. This research relies on BERTopic to identify distinct topics within each field. The study revealed significant shifts in research focus over time, with some disciplines exhibiting robust growth in article numbers such as Periodontics and Prosthodontics. The application of Shannon's entropy revealed an increasing diversification of research efforts in disciplines such as Restorative Dentistry, while others, like Prosthodontics, in spite of their size and their high number of research topics, maintain a more specialized research focus. Taken together, our findings describe the dynamic nature of dental re-search and highlight the balance shifts in research focus across several key areas of Dentistry.

Steel surface protection with hard coatings is essential in the metalworking industry, yet developing high-performance hard coatings still remains a challenge. Quaternary nitride coatings, particularly TiAlSiN, have been extensively studied, but commercial TiAlSiN coatings vary widely, and there is a lack of consistent data. This study presents findings on the development and evaluation of TiAlSiN and TiAlSiN/TiN thin films, with an 800 nm thick TiAlSiN top coating and a 100 nm thick TiN mid-coating. The films were deposited on C120 tool steel discs via reactive DC magnetron sputtering. Ti and TiAlSi 75–20–5 (at.%) disc-shaped targets (50.8 mm diameter × 6.3 mm thickness), fabricated by our team through spark plasma sintering, were used for the sputtering process. Coatings were grown on smooth steel substrates heated to 300 °C, resulting in a uniform micro-structure with nanoparticles of globular (TiN) or pyramidal shape (TiAlSiN), as evidenced by SEM analysis. Nanoindentation tests showed superior mechanical properties for all coatings compared to the steel substrate. Micro-scratch tests indicated better scratch resistance for TiAlSiN/TiN bilayer (BL) coatings than for TiAlSiN single-layer (SL) coatings. Electrochemical impedance spectroscopy tests in a 3.5 wt.% NaCl solution revealed that the BL coatings demonstrated superior corrosion resistance compared to the SL coatings, even after thermal aging at 800 °C for 1 hour. The superior properties of the synthesized TiAlSiN/TiN films recommend them as protective coatings for tool steel surfaces.

Analysis of non-stationary and nonlinear sound signals obtained from dynamical processes is one of the greatest challenges in signal processing. Turning machine operation is a highly dynamic process persuaded by many events such as dynamical responses, chip formations and operational conditions of machining. Traditional and widely used fast Fourier transformation and spectrogram is not suitable for processing sound signals acquired from dynamical systems as its result have significant deficiencies because of stationary assumptions and having priori basis. The relatively new technique, Discrete Wavelet Transform, which uses Wavelet decomposition and the recently developed technique, Hilbert Huang Transform (HHT) which uses Empirical Mode Decomposition have notably better properties in the analysis of nonlinear and non-stationary sound signals. This paper presents a comparative study on the decomposition of multicomponent sound signals using Empirical Mode Decomposition and Wavelet Decomposition to highlight the suitability found in HHT to analyze tool-emitted sound signals received from turning processes. Apart from the short mathematical and theoretical foundations of the transformations, this paper demonstrates their decomposition strength using an experimental case study of tool flank wear monitoring in turning. It also concludes HHT is more suitable than DWT to analyze tool-emitted sound signals received from turning processes.

Sarcopenia is associated with clinical complications, which increase mortality. Effective sarcopenia risk screening in the elderly should be grounded in a comprehensive assessment, encompassing both nutritional status and medication use. Current screening tools, while emphasizing muscular per-formance, exhibit limited sensitivity in identifying elderly individuals at risk of sarcopenia. This cross-sectional study aimed to develop a sarcopenia risk screening tool, named Sarc-Global, with enhanced sensitivity, incorporating factors pertinent to the overall health of the elderly. Utilizing the criteria established by EWGSOP2 for diagnosing sarcopenia, we evaluated 395 communi-ty-dwelling elderly individuals. This evaluation served as a reference for assessing the efficacy of two validated questionnaires, Sarc-F and Sarc-CalF, and our newly developed Sarc-Global. Con-structed through multiple logistic regression, Sarc-Global integrates variables such as sex, age, medication use, body mass index, arm circumference, and handgrip strength – all significantly associated with sarcopenia (p

Rotor blade bearings enable the rotor blades to pivot about their longitudinal axis and thus control the power output and reduce the loads acting on the wind turbine. Over a design period of 20 years, rolling bearings are exposed to frequent oscillating movements with amplitude ratios of x/2b>1, especially due to new control concepts such as Individual Pitch Control, which can lead to wear and a reduction in service life. The objective of the paper is to identify the dominant wear mechanisms and their consequences for the operation of oscillating bearings. Oscillating experiments with increasing number of cycles on angular contact ball bearings of two different sizes (type 7208 and 7220), show that the damage initiation starts with adhesive and corrosive wear mechanisms, which result in a sharp increase of the torque as well as the wear volume on the bearing raceway. As the number of cycles increases, an abrasive mechanism occurs, resulting in a lower slope of the wear curve and a smoothing of the resulting wear depressions. The wear and torque curves are evaluated and classified using an energy-wear approach according to Fouvry.

Beetles are by far one of the most successful and diverse insect species. A part of this success is attributed to their elytra which provide various functions such as protection to their bodies from mechanical forces and the harmful environmental factors. In this study, Stag beetle (Lucanus cervus) elytra were first examined for their overall flexural properties and were observed to have a localized shape retaining snap-through mechanism which could play a crucial role in energy absorption, e.g. during battles and falls from heights. The snap-through mechanism was validated using theoretical calculations and also finite element simulations. Elytra were also characterized to examine their puncture and wear resistance. Our results show that elytra resisted puncture up to a force of 1.8±0.4 N and have puncture resistance compared to that of commercially available puncture resistant gloves. The measured values of modulus and hardness of elytra exocuticle were 10.3±0.8 GPa and 0.7±0.1 GPa. Using the hardness to modulus ratio as an indicator of wear resistance, the estimated value was observed to be in the range of wear resistant biological materials. Thus, our study demonstrates different mechanical properties of the stag beetle elytra which can be explored to design shape retaining bio-inspired composites with enhanced puncture and wear resistance.

A review of the surface ablation of hominin teeth by attrition, abrasion and erosive wear. The occurrence of these lesions is explored in a sample of South African fossil australopithecine dentitions revealing excessive wear. Interpretation of the nature of the dietary components causing such wear in the absence of carious erosion provides insight into the ecology of the Plio-pleistocene epoch (1-2 million years ago). Fossil teeth inform much of the living past by their retained evidence after death. Tooth wear is the ultimate forensic evidence of lives lived.

Peri-implant infective diseases seem to be the most common cause for the late dental implant failure. Therefore, peri-implant microbiota has been intensively studied in modern implantology. Many studies showed a presence of extremely varied microflora in cases of peri-implant infective diseases. The main scope of this observational single-blind study was to analyze the presence of some microbial species in a group of patients with clinical signs of peri-implant mucositis compared to two other groups (patients treated with dental implants but without any clinical signs of peri-implant inflammation and patients treated with no dental implants). The identification of microorganisms was followed by an antibiogram in order to find their sensitivity to various antibiotics. The results showed a microbiota not necessarily specific for each situation (peri-implant infective diseases, healthy tissues around dental implants and healthy natural teeth and gums) with species like Candida albicans, Neisseria mucosa, Prevotella, Staphylococcus aureus, Streptococcus and others. Peri-implant infective diseases presented more bacterial species than other conditions.

High entropy alloys have excellent wear resistance, so they have great application prospects in the fields of wear resistance and surface protection. In this study, the wear resistance of FeNiCrCoCu high entropy alloy coating was systematically analyzed by molecular dynamics method. FeNiCrCoCu high entropy alloy was used as a coating material to adhere to the surface of Cu matrix. The friction and nano indentation simulation of this coating material were carried out by controlling the ambient temperature. The influence of temperature on its friction properties was analyzed from five aspects: lattice structure, dislocation evolution, friction coefficient, hardness and elastic modulus. The results show that with the increase of temperature, the disorder of the lattice structure increases, which leads to the increase of the tangential force and the friction coefficient in the friction process. At 300K and 600K, the ordered lattice structure of the high entropy alloy coating material is basically the same, and thus their hardness is basically the same. However, the dislocation density at 600K is significantly reduced compared with that at 300K, resulting in the increase of the elastic modulus of the material from 173GPa to 219GPa. At the temperatures of 900K and 1200k, lattice disorder take place rapidly, and dislocation density also decreases significantly, resulting in a significant decrease in the hardness and elastic modulus of the material. When the temperature reaches 900K, the wear resistance of the FeNiCrCoCu high entropy alloy coating decreases sharply. This work is of great value to the analysis of wear resistance of high entropy alloy at high temperature.

Digital photogrammetry has attracted widespread attention in the field of geotechnical and geological survey due to its low-cost, ease of use and contactless mode. In this work, with the purpose of studying the progressive block surficial detachments of a landslide we developed a monitoring system based on fixed multi-view time-lapse cameras. Thanks to a new-developed photogrammetric algorithm based on the comparison of photo sequences through a structural similarity metric and the computation of the disparity map of two convergent views we can quickly detect the occurrence of collapse events, determine their location and calculate the collapse volume. With the field data obtained at the Perarolo landslide site (Belluno Province, Italy), we have preliminary tested the effectiveness of the algorithm and its accuracy in the volume calculation. The method of quickly and automatically obtaining collapse information proposed in this paper can extend the potentials of landslide monitoring system based on videos or photo sequence and it will be of great significance for further research on the link between the frequency of collapse events and the driving factors.

Magnetogenetics emerges as a transformative approach for modulating cellular signaling pathways through the strategic application of magnetic fields and nanoparticles. This technique leverages the unique properties of magnetic nanoparticles (MNPs) to induce mechanical or thermal stimuli within cells, facilitating the activation of mechano- and thermosensitive proteins without the need for traditional ligand-receptor interactions. Unlike traditional modalities that often require invasive interventions and lack precision in targeting specific cellular functions, magnetogenetics offers a non-invasive alternative with the capacity for deep tissue penetration and the potential for targeting a broad spectrum of cellular processes. This review underscores magnetogenetics' broad applicability, from steering stem cell differentiation to manipulating neuronal activity and immune responses, highlighting its potential in regenerative medicine, neuroscience, and cancer therapy. Furthermore, the review explores the challenges and future directions of magnetogenetics, including the development of genetically programmed magnetic nanoparticles and the integration of magnetic field-sensitive cells for in vivo applications. Magnetogenetics stands at the forefront of cellular manipulation technologies, offering novel insights into cellular signaling and opening new avenues for therapeutic interventions.

Friction and wear take place on two solid surfaces in sliding contact as a result of the mechanical, thermal and chemical interactions with the participation of environmental species. Electron microscopy and the associated spectroscopic analyses are powerful in probing these mechanisms in spatial resolutions from micro to atomic scale. This article provides a review of the author’s work in the wear and friction mechanisms of PVD hard coatings in which various SEM- and TEM-based microscopic and spectroscopic techniques were employed. Understanding on the failure mechanisms and the origin of self-adaptive friction has been improved to nano-scale. Other related issues are also discussed, such as sample preparation techniques for cross-sectional electron microscopy, energy dispersive X-ray spectroscopy and electron energy loss spectroscopy.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

The oral microbiome, studied by sampling the saliva or oral rinse, has been long thought to have diagnostic capacity for head and neck cancers (HNC). However, previous reports on the HNC oral microbiome provide inconsistent results. The aim of this study is to consolidate these datasets and determine the oral microbial composition between HNC patients to healthy and premalignant individuals. We analyzed 16 published head and neck cancer (HNC) short-read 16S rRNA sequencing datasets, specifically targeting the V3V4, V4 and V4V5 regions. These datasets included saliva and oral rinse samples from donors with HNC, as well as from healthy and premalignant donors. Differences in diversities and microbial abundance were determined. HNC saliva displayed lower alpha diversity than healthy donors. In contrast, the opposite trend was observed for oral rinse samples. Beta diversity were largely similar across different patient types. Similar oral phyla were detected for all samples, but proportions were largely dependent on sample type (i.e. saliva or oral rinse) and primer set utilised for 16S rRNA sequencing. Neisseria, Leptotrichia and Megasphaera were elevated in healthy saliva, while Mycoplasma was elevated in HNC saliva. Oral rinse and saliva displayed similar enrichment for Fusobacterium, while Veillonella, Alloprevotella, and Campylobacter had conflicting results. The sparse partial least squares discriminant analysis model performed effectively in discriminating HNC from healthy or premalignant patients using V3V4 saliva (AUC = 0.888), and V3V4 oral rinse (AUC = 0.928), while poor discriminative capacity was observed for V4 saliva (AUC = 0.688). In conclusion, our meta-analysis highlighted the limitations of 16S rRNA sequencing, particularly due to variations across study batches, primer sets (i.e. V3V4, V4), and sample types. Hence, caution should be exercised when interpreting 16S rRNA sequencing results across studies, especially when different primer sets and sample types are used.

In this work, we propose an in-house simulation tool designed for the analysis and optimization of bifacial photovoltaic (PV) modules, which are currently under the spotlight in the renewable energy scenario. The tool is conceived to support researchers and engineers by providing fast and accurate predictions of the PV module yield under various operating and environmental conditions. For a chosen geographical site, the impact of module orientation, tilt, albedo, sky conditions, ambient temperature, and so on, can be effortlessly determined. In case of nonuniformity across the cells dictated by localized architectural shading, dirt, bird drops, defects, a circuit-based cell-level approach can be activated to compute the module production. An extensive simulation campaign is performed by assuming that the panels are installed in Naples without loss of generality. Results are shown to give detailed insights into the performance of bifacial modules, thus providing unambiguous guidelines for their correct installation. Further analyses are conducted to demonstrate the tool capability to quantify the detrimental influence of a poorly-irradiated cell on the backside, as well as of cracked cells.

Background: Atopic dermatitis is a chronic condition that significantly affects the daily life of those who suffer from it, requiring complex and personalized management with active participation of the patient in the management of their disease. Objective: to describe the design and development process of a mobile application, using the Design Thinking method, for the follow-up of patients with atopic dermatitis. Methods: User-centered design and prototype creation method, differentiating the phases of the empathize, define, idea, prototype, and test. A purposive snowball sampling was used to recruit patients with atopic dermatitis, family members, and health professionals. Three two-hour workshops were held, attended by 25 people. Results: the parameters to be monitored will include objective data (physical, behavioral, treatments, environmental, integration of daily routines) and subjective data (user experience). On the other hand, it will figure out behavior patterns, set up rewards, foster a feeling of community, and use notifications and a chatbot. Conclusion: The active integration of all stakeholders at each stage of the design and development of the digital solution has improved its relevance and acceptance, resulting in a tool that is expected to significantly improve the management of atopic dermatitis.

Background/objective: Tools to accurately and efficiently measure the dietary intake of Nigeria are lacking. We aimed to develop and assess the usability of a new online dietary assessment tool for Nigeria, myfood24 West Africa. Methods: We developed myfood24 West Africa database using data from existing food composition tables, back-of-pack labels of packaged foods and research articles. A 7-step approach was used: identified data sources, selected foods, processed/cleaned data, calculated nutrient content of recipes, created/allocated portion sizes, quality-checked database, and developed food accompaniments. To pilot myfood24 West Africa, we recruited 179 university staff living in Nigeria using a cross-sectional design; usability was assessed using a questionnaire that incorporated the System Usability Scale (SUS) and feedback session. Results: The database included 924 foods with up to 54 nutrients and 35 portion-size images allocated to foods. 60% of the data were sourced from the 2019 West Africa Food Composition Table, 17% from back-of-pack labels, 14% from the 2017 Nigeria Food Composition Table, 5% from generated recipes and 4% items from published literature. 30% (n=53) self-recorded their diet on their own and 1345 entries were made. The mean SUS score of 74 (95% CI: 68,79) indicated good usability. The feedback showed the tool was easy to use, educative, and included a variety of locally foods consumed. Conclusion: This new tool will enhance the dietary assessment of the Nigerian population. More work will cover more foods from other regions of Nigeria and West African countries.

An investigation was made to determine the effects of tungsten surface coating on the coefficient of friction of sliding contact between lubricated steel surfaces. The four-ball test was modified, using a tungsten carbide ball bearing in the spindle to cause sliding contact onto three hard steel ball bearings coated with tungsten disulfide lamellar dry lubricant coating, with a coating of grease lubrication applied to the ball bearings. The coatings, loads, speed, and grease level was varied to best understand the impact of different conditions to the friction coefficient.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

In the former mining district of La Carolina (southern Spain), waste materials were accumulated without first waterproofing the substrate. Additionally, these mining dams were abandoned without any type of restoration, conditions that present a significant risk of contaminating the surrounding soils and waters. Prior to carry out the necessary works for isolating these residues, morphological characterization of the contact with the base substrate is needed. For that purpose, in recent years, different indirect study techniques have been used, among which electrical to-mography stands out. In this work, a less common geophysical technique, magnetometry, both in its magnetic and gra-diometric modalities, is used as an alternative method to analyse the geometry and structure of a mining dam. The results obtained with this methodology are compared with the results provided by electrical techniques, as well as with direct data from mechanical surveys and aerial photo-graphs prior to waste deposition. The magnetic anomaly curves obtained with geometric models generated with the Mag2dc program were also analysed. This comparative study shows the use-fulness of magnetic prospecting in characterizing the base geometry of these mining structures and therefore the interest in its application to environmental characterization studies.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Wear simulation aims to assess wear rates and their dependence on factors like load, kinematics, temperature, and implant orientation. Despite its significance, there's a notable gap in research concerning advancements in simulator control systems and the testing of clinically relevant waveforms. This study addresses this gap by focusing on enhancing the conventional proportional-integral-derivative (PID) controller used in joint simulators through the development of a fuzzy logic-based controller. Leveraging a single-input-multiple-output (SIMO) fuzzy logic control system, the study aimed to improve displacement control, augmenting the traditional Proportional-Integral (PI) tuning approach. Implementation and evaluation of a novel Fuzzy-PI control algorithm were conducted on the Leeds spine wear simulator. The study also included testing of daily-living (DL) profiles, particularly from the hip joint, to broaden the scope of simulation scenarios. While both the conventional PI controller and the Fuzzy-PI controller met ISO tolerance criteria for the spine flexion-extension (FE) profile at 1Hz, the Fuzzy-PI controller demonstrated superior performance at higher frequencies and with DL profiles due to its real-time adaptive tuning capability. The Fuzzy-PI controller represents a significant advancement in joint wear simulation, offering improved control functionalities and a more accurate emulation of real-world physiological dynamics.

The paper analyzes the phenomenon that condition the durability and reliability of a type of dental bur based on the wear of the active part and with effect on its quality. For the experimental study, a conical-cylindrical dental bur and a sample dental material in cobalt-chromium alloy, cylindrical shape, tested on a specially made experimental installation were used. The paper was limited to the consideration of a single parameter (loss of mass, mw by wear of the active part of the dental bur tested) for the establishment the durability and reliability, useful for the extension of the lifetime or even optimization of its operation. The wear phenomenon of the active part of dental bur is studied based on the results and experimental data obtained in the work process that was validated by interpolation and led to polynomial functions which approximate very well the dependent parameter, mw, considered in the experimental program. The results of the interpolation showed that in the first 11 h of work, the dental bur works with high efficiency, after which it can be easily decommissioned (optimizing operation, possibly constructive solutions); i.e., it should be replaced with a new one (criterion for replacing of worn dental bur).

The concept of friction damper is widespread technique and used to reduce the structural vibrations in many industrial applications. These friction dampers are generally coated with low wear rate materials to reduce the fretting wear. This paper investigates the use of physical vapor deposition (PVD) nitride based AlTiN coating material applied over the stainless steel friction damper to enhance the damping capacity and to reduce the fretting wear. A friction test rig has been developed to measure the dynamic hysteresis characteristics of friction damper at high temperature (700 °C). The damping capacity and fretting wear analysis is carried out at room temperature, 300 °C and 600 °C. The force versus displacment characterisitcs curve is used to predict the damping capacity and fretting wear analysis is carried out at microscopic level for the comparision. It is observed that at room temperature AlTiN coated friction damper has not much influence to improve the damping capacity and to reduce the fretting-wear. However, at high temperature it has better damping capacity and less wear in comparision to uncoated friction damper. Wear behaviour in coated and uncoated damper is different at room temperature and at elevated temperature.

Neurology is a quickly evolving specialty that requires clinicians to make precise and prompt diagnoses and clinical decisions based on the latest evidence-based medicine practices. In all Neurology subspecialties, Stroke and Epilepsy in particular, clinical decisions affecting patient outcomes depend on neurologists accurately assessing patient disability. Artificial intelligence (AI) can predict the expected neurological impairment from an AIS (Acute Ischemic Stroke), the possibility of ICH (IntraCranial Hemorrhage) expansion, and the clinical outcomes of comatose patients. This review article informs readers of artificial intelligence principles and methods. The article introduces the basic terminology of artificial intelligence before reviewing current and developing AI applications in neurology practice. AI holds promise as a tool to ease a neurologist’s daily workflow and supply unique diagnostic insights by analyzing data simultaneously from several sources, including neurological history and examination, blood and CSF laboratory testing, CNS electrophysiologic evaluations, and CNS imaging studies. AI-based methods are poised to complement the other tools neurologists use to make prompt and precise decisions that lead to favorable patient outcomes.

Groundwater is becoming increasingly important in the Pacific Northwest of the USA due to declining snowpack volumes and shifts in precipitation type and timing, all connected with climate change. The Upper Williamson Basin of the Klamath Watershed is a groundwater dominated watershed with massive fluctuations in year-to-year streamflow volumes over the past four decades, including the complete absence of any live flow for several years. The precise relationship between groundwater and streamflow in the basin has been difficult to assess due to a limited number of monitoring wells and significant gaps in the water level time history. To address this challenge, we use a novel imputation technique that leverages Earth observations and machine learning to impute gaps in water level records. We use these more complete datasets to compute a groundwater storage change time series for the basin. We show that groundwater storage is highly correlated to streamflow and that groundwater storage is correlated to rainfall with a three- to four-year delay that appears variable depending on groundwater storage volumes. The tools and relationships we present make it possible for water managers to estimate when streamflows will return to the basin and be more informed to support better management.

Conventional heat treatment is not capable of converting a sufficient amount of retained austenite into martensite in high-carbon or high-carbon and high-alloyed iron alloys. Cryogenic treatment induces the following alterations in the microstructures: (i) a considerable reduction in the retained austenite amount, (ii) formation of refined martensite coupled with an increased number of lattice defects, such as dislocations and twins, (iii) changes in the precipitation kinetics of nano-sized transient carbides during tempering, and (iv) an increase in the number of small globular carbides. These microstructural alterations are reflected in mechanical property improvements and better dimensional stability. A common consequence of cryogenic treatment is a significant increase in the wear resistance of steels. The current review deals with all the mentioned microstructural changes as well as the variations in strength, toughness, wear performance, and corrosion resistance for a variety of iron alloys, such as carburising steels, hot work tool steels, bearing and eutectoid steels, and high-carbon and high alloyed ledeburitic cold work tool steels.

Stainless steel grade AISI 304 is one of the most widespread modern structural material, alas its sliding wear and cavitation wear resistance are limited. Thus, AlTiN and TiAlN coatings can be deposited for increasing the resistance to wear of stainless steel components. The aim of the work was to investigate the cavitation erosion and sliding wear mechanisms of magnetron sputtered AlTiN and TiAlN coatings deposited on SS304 stainless steel. Films surface morphology and structure were examined using a profilometer, light optical microscope (LOM) and scanning electron microscope (SEM). The mechanical properties (hardness, elastic modulus) were tested by nanoindentation tester. The adhesion of deposited coatings was determined by means of the scratch test and Rockwell test. Cavitation erosion tests were performed according to ASTM G32 (vibratory apparatus) with stationary specimen procedure. Sliding wear tests were conducted using a nano-tribo testes i.e. ball-on-disc apparatus. Wear mechanisms are strongly contingent upon the structure and morphology of the tested materials. In relation to stainless steel substrate, the PVD films present a superior resistance to sliding wear and cavitation erosion. Higher resistance was noticed for AlTiN than for TiAlN film, mainly due to its superior hardness and elastic modulus. Cavitation erosion mechanism of both, AlTiN and AlTiN coatings is prone to embrittlement, imputable to fatigue processes that result in coating rupture and spallation that consist in coating fragmentation, formation of pits and finally detachment from the substrate. Additionally, films nanoindentation results measured before and after cavitation testing indicate changes in coatings structure, that acknowledged wear mechanism that starts with coating internal delamination in flake spallation mode. In contrary to PVD coatings, steel substrate is characterized by developed cavitation erosion wear with roughened surface and plastically deformed, semi-brittle, eroded surface. Sliding wear of thin films is based on micro-ploughing mechanism. For stainless steel adhesive sliding wear mode and plastic deformation with smearing, material transfer and grooving were observed. It was confirmed that various fluid machinery components made from austenitic stainless steel that undergo cavitation erosion, can be prevented by deposition of AlTiN and TiAlN films.

In the present paper, Co-B/SiC composite coatings were obtained via electrodeposition from colloidal suspensions with different concentrations of SiC particles and subsequent heat treatments at 350 °C. The composition, morphology and structure of the Co-B/SiC composite coatings were analyzed using glow discharge spectrometry (GDS), scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Hardness and tribological properties were also studied. The results showed that an increase in the SiC concentration in the colloidal suspensions resulted in both an increase in the SiC content and a decrease in the B content in the obtained Co-B/SiC coatings. The Co-B/SiC coatings were adherent, glossy and soft and exhibited a homogeneous composition in all thicknesses. By contrast, an increase in the SiC particle content of the Co-B/SiC composite coating from 0 to 2.56 at.% SiC reduced the hardness of the film from 680 to 360 HV and decreased the wear volume values from 1180 to 23 mm³ N^-1 m^-1, respectively (that is, the wear resistance increased). Moreover, when the Co-B/SiC coatings with SiC content ranging from 0 to 2.56 at.% SiC were subjected to a heat treatment process, the obtained coating hardness values were in the range of 1200 to 1500 HV and the wear volume values were in the range of 382 to 19 mm³ N^-1 m^-1.

Multifunctional landscapes are complex systems that integrate biophysical, cultural-historical and socio-economic components into unique territorial structures and regional ensembles. Facing increasing pressures generated by urbanization, climate change and overexploitation of natural resources, assessing the sustainability of these landscapes has become an urgent priority. The present research is based on the development and parametrization of a new tool for evaluating the sustainability of multifunctional landscapes that aims to measure the level of biocultural resilience of a landscape, integrating biological, cultural and socio-economic indicators in a single analytical framework. This index, called the biocultural resilience index (BRI), provides a holistic perspective on the dynamics of landscapes, allowing the identification of vulnerability areas and the development of conservation and sustainable management strategies. The evaluation of the of multifunctional landscapes sustainability requires a comprehensive approach that has to integrate both biological aspects, such as biodiversity and ecosystem health, as well as identity and cultural aspects, such as cultural value and the relationship of the local communities with the environment. In this context, this study highlights the fact that the development of appropriate tools and methods for assessing and monitoring the sustainability of multifunctional landscapes becomes essential for their sustainable management and for protecting the benefits they offer to society. Our findings show that the biocultural resilience index (BRI) can be used in a variety of contexts and fields, including spatial planning, biodiversity conservation, sustainable rural development and ecotourism. In the meanwhile, this index offers a robust and flexible analytical framework, adaptable to the needs and particularities of different regions and communities.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

This work aims to explore the impact of side loads, drill-pipe tool-joint (DP-TJ) speed (RPM), and mud type on the austenitic stainless steel SM2535-110 casing wear characteristics. Actual field drill pipe tool joints, casings, and drilling muds are used in this study. The results of the study show that under both types of lubrication, the wear volume increased with radial load and DP-TJ speed. SM2535-110 casing specimens tested under oil-based mud (OBM) lubrication had higher casing wear volumes than those obtained under water-based mud (WBM) lubrication. This unexpected behavior is mainly due to the increase in the surface hardness of the casing specimens tested under WBM. The results also show that the specific wear factor (K) values of specimens tested under WBM are in general 2 to 4 times higher than those obtained under OBM. While K values under WBM increase with both the side load and RPM, those under OBM show a sharp decrease with RPM. This behavior under OBM is due to this lubricant’s higher viscosity and the change of lubrication regime from thin film to thick film lubrication at higher RPM. Scanning electron microscopy (SEM) and the digital microscopic imaging (DMI) of SM235-110 casing specimens show that an aggressive combination of adhesive, abrasive, and plastic deformation was observed under WBM, while the dominant wear mechanism under OBM is abrasive wear.

Early childhood may be a stressful period for families with a significant impact on parents’ mental health and the child’s healthy development. The goal of the SKKIPPI cohort study was to assess the occurrence and determinants of psychosocial stress and mental health disorders in parents as well as in their offspring in early childhood in three German regions. Based on random samples from three residents' registration offices, parents with infants up to 12 months of age at the time of sampling, were invited to participate in the study. A screening online questionnaire was newly developed, available in four languages, to assess common psy-chosocial stressors and mental health problems of parents with small children. The study enrolled 4,984 mothers and 962 fathers. The most common potential psychosocial stressors at baseline were professional problems (mothers 22%, fathers 33%), lack of social sup-port (20%, 14%), and severe, negative experiences in childhood (22%, 16%). Obses-sive-compulsive thoughts (21%, 16%), depressive (9%, 9%) and anxiety symptoms (11%, 7%) were the most frequently reported mental health problems by both parents. Regulatory prob-lems of the child were reported by between 1.5% and 5.1% of parents. The SKKIPPI study showed that a substantial proportion of parents are burdened by psychoso-cial problems and suffer from mental health problems in the first years after birth. Early pre-ventive and low-threshold support measures should be available in the health and social care system. The newly developed questionnaire can be used to screen in the relevant populations in order to avoid disturbances in the mother-child attachment.

In cutting processes tool condition affects the quality of the manufactured parts. As such an essential component to prevent unplanned downtime and to assure machining quality is having information about the state of the cutting tool. The primary function of it is to alert the operator that the tool has reached or is reaching a level of ware beyond which behavior is unreliable. In this paper the tool condition is being monitored by analyzing the electric current on the main spindle via an artificial intelligence model utilizing a LSTM neural network. In the current study the tool is monitored while working on a cylindrical raw piece made of AA6013 aluminum alloy with a custom polycrystalline diamond tool, for the purposes of monitoring the ware of these tools. Spindle current characteristics were obtained using external measuring equipment to not influence the operation of the machine included in a larger production line. As a novel approach, an artificial intelligence model based on a LSTM neural network is utilized for the analysis of the spindle current obtained during a manufacturing cycle and assessing the tool ware range in real time. The neural network was designed and trained to notice significant char-acteristics of the captured current signal. The conducted research serves as a proof of concept for use of a LSTM neural network-based model as a method of monitoring the condition of cutting tools.

This study presents the computational model to determine the wear behaviour of polymer gears. Using PrePoMax finite element numerical calculation software, a proposed computational model was built to predict wear behaviour based on Archard's wear model. This allows the calculation of the wear depth in each loading cycle with constant mesh updating. The developed computational model has been evaluated on the spur gear pair, where the pinion made of POM has meshed with a support gear made of steel. The computational results that were obtained were compared with the analytical results according to the VDI 2736 guidelines. Based on this comparison, it was concluded that the proposed computational model could be used to simulate the wear behaviour of contacting mechanical elements like gears, bearings, etc. The main advantage of the model, if compared to the standardised procedure according to the VDI 2736 guidelines, is the geometry updating after a chosen number of loading cycles, which enables a more accurate prediction of wear behaviour under rolling/sliding loading conditions.

To improve the wear resistance of polyimide (PI), surface modification was developed. In this study, the tribological properties of graphene (GN), graphene oxide (GO), and KH550-grafted graphene oxide (K5-GO) modified PI were evaluated by molecular dynamics (MD) at the atomic level. The findings indicated that the addition of nanomaterials can significantly enhance the friction performance of PI. The friction coefficient of PI composites decreased from 0.253 to 0.232, 0.136, and 0.079 after coating GN, GO and K5-GO, respectively. Among them, the K5-GO/PI exhibited the best surface wear resistance. Importantly, the mechanism behind the modification of PI was thoroughly revealed by observing the wear state, analyzing the changes of interfacial interactions, interfacial temperature, and relative concentration.

Being one of the most critical phases of a flight, landing deserves specific attention, especially when the aircraft is subject to external disturbances such as wind. A notable concern associated with touchdown events, especially when crosswind is present is tire wear. This work is aimed first at developing a nonlinear flight simulator able to handle the entire landing maneuver in non-null wind conditions, considering the airborne phase, ground run, and the transition between them. Then, the simulator is included in an optimal process to define the landing technique associated with the minimum tire wear. The methodology is tested in a simulation environment with a realistic model of a reference aircraft, showing that a significant reduction of tire wear can be obtained by optimizing the sideslip angle at touchdown and the lateral-directional controls after the airplane touches the runway with both legs of the main landing gear.

This paper presents the results of the investigation of composite sinters W-TiB2 which were used as an electrode in the process of electro-spark deposition (ESD) and the examination of the deposited layers. The scope of the study includes detailed characteristics of powder mixtures, composite sinters made using the spark plasma sintering method (SPS) and layers deposited in the electro-spark process. The ESD process, using the W+30 vol.% TiB2 electrode, was carried out using an automated device. The substrates were made of copper and aluminium. The topography analysis of the surfaces of the composite layer and the evaluation of their wear resistance properties are also presented. The analysis of the results of research showed the possibility to obtain, using the SPS method, composite materials of good quality, which can be used as electrodes in the ESD process. The obtained layers had increased wear resistance in relation to the substrate material.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

The structural and strength analysis of the material used to construct such an important engine element as the turbine is of great significance, both at the design stage as well as during tests and expertises related to emergency situations. Bearing in mind the conditions above mentioned, the paper presents the results of research on the chemical composition, morphology and phased structure of the metallic construction material used to produce the blades of the high and low pressure turbine of the RD-33 jet engine, which is the propulsion unit of the MiG-29 aircraft. The data obtained as a result of the material tests of the blades allowed, on the basis of the analysis of chemical composition and phased structure, to determine the grade of the alloy used to construct the tested elements of the jet engine turbine. The structural stability of the material was found to be lower in comparison with engine operating conditions, which manifested itself as a clear decrease in the resistance properties of the blade material. The results obtained can be used as a basis for analyzing the life span of an object or a selection of material replacements, which enable to produce the analyzed engine element.

Wastewater-based surveillance has emerged as an important method for monitoring SARS-CoV-2. This study investigated the presence of SARS-CoV-2 in wastewater in Zambia. We conducted a longitudinal study in the Copperbelt and Eastern provinces of Zambia from October 2023 to December 2023 during which 155 wastewater samples were collected. The samples were subjected to three different concentration methods, namely bag-mediated filtration, skimmed milk flocculation, and polythene glycol-based concentration assays. Molecular detection of SARS-CoV-2 nucleic acid was conducted using real-time PCR. Whole genome sequencing was conducted using Illumina COVIDSEQ assay. Of the 155 wastewater samples, 62 (40%) tested positive for SARS-CoV-2. Of these, 13 sequences of sufficient length to determine SARS-CoV-2 lineages were obtained and two sequences were phylogenetically analyzed. Various Omicron subvariants were detected in wastewater including BA.5, XBB.1.45, BA.2.86, and JN.1. Some of these subvariants have been detected in clinical cases in Zambia. Interestingly, phylogenetic analysis positioned a sequence from the Copperbelt Province in the B.1.1.529 clade, suggesting that earlier Omicron variants detected in late 2021 could still be circulating and may not have been wholly replaced by newer subvariants. This study stresses the need for integrating wastewater surveillance of SARS-CoV-2 into mainstream strategies for monitoring SARS-CoV-2 circulation in Zambia.

In this study, the potential of Fe3Al coating material as an environmentally friendly alternative to coatings containing critical elements for brake discs was investigated. A buffer layer of Cr-Mo steel (Ferro 55) was applied to enhance coating quality and prevent the formation of hot cracks during solidification. Microstructural analysis of the cross-section of the coating showed that the buffer layer diffused into the Fe3Al coating, forming a combination of Fe3Al, Fe, and Fe3AlC0.5 phases. The tribological properties of the Fe3Al coating were evaluated by pin-on-disc tests using two different copper-free friction materials extracted from commercial brake pads. The wear results showed a coefficient of friction comparable to that of an uncoated disc, but with a reduction in Particulate Matter (PM) emissions, an interesting aspect that is gaining increasing importance in view of the upcoming international standards..

Determining the estrous cycle stages in mice is essential for optimizing breeding strategies, synchronizing experimental time lines, and facilitating studies in behavior, drug testing, and genetics. It is critical for reducing the production of genetically unmodified offspring in the generation and investigation of genetically modified animal models. An accurate detection of the estrus cycle is particularly relevant in the context of the 3Rs—Replacement, Reduction and Refinement. The estrous cycle, encompassing the reproductive phases of mice, is key to refining experimental designs and addressing ethical issues related to the use of animals in research. This study presents results from two independent laboratories on the efficacy of the Mouse Estrus Detector (MED) from Elmi Ltd. (Latvia) for the accurate determination of the estrus phase. The female mice of five strains/stocks (CD1, FVB/N, C57Bl6/J, B6D2F1, and Swiss) were used. The results showed that the MEDProTM is a low -traumatic, simple, rapid and painless method of estrus detection that supports the principles of the 3Rs. The use of the MEDProTM for estrus detection in mice caused minimal stress, enhanced mating efficiency, facilitated an increase in the number of embryos for the in vitro fertilization and allowed the production of the desired number of foster animals.

Variable and sometimes contrasting effects of using artificial rhizobium inocula to increase grain legume performance have been reported. The objectives of this systematic review and meta-analysis were therefore to (i) estimate the overall effect of rhizobium inocula on grain yield and protein content and (ii) identify potential confounding factors that explain the observed variation. A web of Science database literature search was carried out in 2016. Data from all field experiments, greenhouse and pot experiments that compared grain yields and protein contents in Rhizobium/Bradyrhizobium-inoculated with non-inoculated control crops were extracted and analyzed using previously described unweighted and weighted meta-analysis protocols. GRADE assessments of the strength of evidence of results from the weighted meta-analyses were carried which included an assessment of the risk of publication bias. Results: For unweighted meta-analyses we identified eligible data in 236 and 36 studies for grain yield and protein content respectively. For weighted meta-analyses we identified eligible data in 92 and 8 studies for grain yield and protein content respectively. Rhizobium inoculation was found to (i) significantly increase grain yield in both the unweighted (mean percent difference: 41%, 95%CI 36,46, p<0.0001) and weighted meta-analysis (Standardized mean difference: 1.56, 95%CI 1.26,1.87, p<0.0001) and (ii) significantly increase protein content in the unweighted meta-analysis (mean percent difference: 11%, 95%CI 5,18, p<0.0001), but not the weighed meta-analyses which only detected a trend (0.1>p>0.05) towards higher protein content in inoculated grain legume crops. Multi-level model-based weighted meta-analyses suggest that the (i) type of experiment, (ii) type of fertilizer used in experiments, (iii) grain legume type/species and (iv) the country in which experiments were carried out, were confounding factors. The main limitation of the evidence is that a large number of publications did not report measures of variation and could therefore not be included in the more scientifically sound weighted meta-analyses. However based on the large evidence-base available for grain yield it can be concluded that overall Bradyrhizobium/Rhizobium seed inoculation results can increase grain yield by ~40% compared with non-inoculated grain legume crops.

The paper contains the results of the 100-hour test campaign of the Additive Manufactured (AM) spare part (retainer – slipper) dedicated for an exact axial piston pump. The material of the retainer-slipper has been identified by using energy dispersive spectroscopy and replaced by other – with similar material properties as the original one. The obtained spare part had been subjected to only one postprocessing type (sandblasting) to analyze the influence of the rough part after the AM process. The whole test campaign has been divided into stages, where after each stage microscopic measurements have been made. During microscopical investigation roughness and geometrical measurements were conducted. The results revealed that it is possible to replace parts in hydraulic pumps with the use of AM. 100-hour test campaign caused about 500% increase in the surface roughness of the pump’s original part which was cooperated with the AM spare retainer-slipper, without any damages to the test system.

The paper examines the possibility of increasing the wear and corrosion resistance of a CP-Ti surface by duplex plasma electrolytic treatment (borocarburizing and polishing). The structure and composition of diffusion layers, their microhardness, surface morphology and roughness, wear resistance during dry friction and corrosion resistance in Ringer's solution were studied. The formation of a surface hardened layer up to 200 m thick with a microhardness of up to 950 HV, including carbides and a solid solution of boron and carbon, is shown. Subsequent polishing makes it possible to reduce surface roughness and remove weak areas of the porous oxide layer, which is formed during high-temperature oxidation in aqueous electrolyte vapor during borocarburizing. Changing the morphology and structural-phase composition of the CP-Ti surface helps reduce weight wear by 3 times (the mode of frictional interaction changes from microcutting to oxidative wear) and corrosion current density by 4 times after borocarburizing in a solution of boric acid, glycerin and ammonium chloride at 950 °C for 5 minutes and subsequent polishing in an ammonium fluoride solution at a voltage of 250 V for 3 minutes.

Tungsten carbide inserts (TCI) and polycrystalline diamond compact (PCD) cutters used in two types of drill bits for drilling oil and gas wells were evaluated by a pin-on-disc test. The morphology of the worn surface was characterized by scanning electron microscopy (SEM). The behavior of corrosion resistance was evaluated with the electrodynamic polarization technique. The polycrystalline diamond compact cutter has a higher hardness, better corrosion, and wear behavior compared to tungsten carbide.

Climate warming is expected to have pronounced effects on Arctic and Subarctic ecosystems, especially regions underlain by discontinuous and relatively warm permafrost. The main goal of this research is to evaluate the vulnerability and dynamics of permafrost under climate warming across the various ecotypes in respect of ecosystem stability, socioeconomic impact, and for better understanding possible future environmental changes. We suggested the new version of the spatially distributed permafrost dynamics model (GIPL2-MPI), which is developed in the Geophysical Institute, University of Alaska Fairbanks. This model is based on the ecosystem approach to simulate the permafrost dynamics, which we are discussing in this paper. We combined ground-based observations and numerical freeze/thaw modeling using climate-ecosystem-permafrost interactions to understand the physical processes and mechanisms controlling permafrost physical state. We predict the changes in permafrost conditions using output from two GCMs (NCAR-CCSM4 and GFDL-CM3) and Five-Model Average Ensemble for the RCP-4.5 and RCP-8.5 scaled down to 1 by 1 km spatial resolution (https://uaf-snap.org/) across entire Alaska. Our result shows that by the end of the current century widespread near-surface permafrost degradation could begin everywhere in Alaska southward of the Brooks Range as well as across some spots at the North Slope Alaska.

This manuscript deals with the cavitation erosion resistance of low-velocity oxy-flame (LVOF) sprayed Al2O3–40%TiO2/NiMoAl cermet coatings, a new functional application of cermet coatings. The aim of the study was to investigate the cavitation erosion mechanism and determine the effect of feedstock powder ratio (Al2O3–TiO2/NiMoAl) of LOVF cermet coatings on their cavitation erosion resistance. As-sprayed coatings were investigated for roughness, porosity, hardness, Young’s modulus. Microstructural characteristics of the cross-section and the surface of as-sprayed coatings were examined by light optical microscopy (LOM) and scanning electron microscopy (SEM) equipped with the EDS and XRD methods. Coatings cavitation tests were conducted in accordance with the ASTM G32 standard with usage of reference samples made from steel, copper and aluminum alloys. Cavitation erosion resistance was measured by weight and volume loss, and normalised cavitation erosion resistance was calculated. Surface eroded due to cavitation was examined in successive time intervals by LOM and SEM-EDS. On the basis of coating properties and cavitation investigations, a phenomenological model of the cavitation erosion of Al2O3–40%TiO2/NiMoAl cermet coatings was elaborated. General relationships between their properties, microstructure and cavitation wear resistance were established. The Al2O3–40%TiO2/NiAlMo composite coating containing 80% of ceramic powder has a higher cavitation erosion resistance than the reference aluminium alloy.

Chatbots are increasingly used as tools for disseminating knowledge and information across various sectors of business, without the need for human intervention. With the continuous advancement of technology and the internet, the field of cybersecurity is also expanding, leading to the development of newer and more sophisticated systems to counter emerging threats. However, a fundamental question arises: how can one determine what to look for, where to acquire the necessary knowledge, and how to initiate this process? Recognizing the need for more effective tools in the market to educate individuals about online threats and self-protection, this paper aims to bridge the gap in the existing literature. The Artificial Intelligence-based Cybersecurity Chatbot (AICyberSec) has been developed to provide a versatile cybersecurity knowledge resource. This initiative is in response to the absence of a comprehensive solution in the market that effectively informs individuals about online threats and offers guidance on how to safeguard themselves. Furthermore, this chatbot serves as a valuable application for identifying potential hazards in cyberspace and can also function as an educational tool to facilitate the learning process.

Microsystems are key enabling technologies, with applications found in almost every industrial field, including in-vitro diagnostic, energy harvesting, automotive, telecommunication, drug screening, etc. Microsystems, such as microsensors and actuators, are typically made up of components below 1000 microns in size that can be manufactured at low-unit cost through mass-production. Yet, the development of microsystems for commercial or educational purposes, has typically been limited to upper income countries due to the initial investment costs associated with the microfabrication equipment and processes. However, recent technological advances have enabled the development of low-cost microfabrication tools. In this paper, we describe a range of low-cost approaches and equipment (below £1000), developed or adapted and implemented in our laboratories. We describe processes including photolithography, micromilling, 3D printing, xurography and screen-printing used for the microfabrication of structural and functional materials. The processes that can be used to shape a range of materials with sub-millimetre feature sizes are demonstrated here in the context of Lab-on-Chips, but they can be adapted for other applications. We anticipate that this paper, which will enable researchers to build a low-cost microfabrication toolbox in a wide range of settings, will spark a new interest in microsystems.

The aim of the study was to test the significance of the EPT index in the water quality assessment of three types of water bodies in hilly and mountainous region of Serbia. The aquatic macroinvertebrate community was dominated by the group of insects, of which 95 taxa represent the EPT group. We compared the obtained values of biological indices used for the assessment of water quality according to the national legislation with the overall status assessment represented by the ecological quality classes (EQC). The results of the Spearman correlation test showed a negative correlation of EQC with the EPT index, BMWP score, H', total number of taxa and number of sensitive taxa, while a positive correlation was observed for the values of SI and Tubificinae %. The values of EQC and biological indices were subjected to principal component analysis (PCA). The results showed that the parameters that contributed most to the differences were the EPT index, the BMWP score and the number of sensitive taxa. The results indicate that the EPT index is an excellent indicator of changes in water quality and an important tool for the ecological categorization of water bodies in mountain regions.

Falls are considered a significant cause of disability, pain, and premature deaths in older adults, often due to sedentary lifestyles and various risk factors. Combining immersive virtual reality (IVR) with physical exercise, or exergames, enhances motivation and personalizes training, effectively preventing falls by improving strength and balance in older people. IVR technology may increase the ecological validity of the assessments. The main goal of our study was to assess the feasibility of using a KAVE-based VR platform combining simulations of Levadas and a Cable Car to perform a balanced assessment and profiling of the older adult population for high risk-of-falls and the related user experience. A VR-based platform using a Wii balance board and a CAVE was developed to assess balance and physical fitness. Validated by the Biodex Balance System (BBS), 25 older adults participated in this study. The usability and presence were measured through the System Usability Scale and ITC-SOPI questionnaires, respectively. The IVR system showed a high presence and a good usability score of 75. Significant effects were found in the maximum excursion of the Centre of Pressure (COP) on the anterior-posterior axis during the Cable Car Simulation (CCS), correlating with BBS metrics. Multiple discriminative analysis models and the support vector machine classified fall risk with moderate to high accuracy, precision, and recall. The system accurately identified all high-risk participants using the Leave-One-Out method. This study suggests that an IVR-based platform based on simulations with high ecological validity can be used to assess physical fitness and identify individuals at a higher risk of falls.

Focus Group Discussions (FGDs) are widely employed in qualitative research to delve into complex social issues, yet their application in conservation studies lacks standardised guidelines and thorough evaluation. This review assesses the utilisation of FGDs in biodiversity and conservation research from 2000 to April 2022, identifying 170 pertinent articles, primarily published between 2015 and 2022. FGDs, often integrated with other methodologies, predominantly sought to understand community perspectives, evaluate conservation practices, explore challenges, and document indigenous knowledge. Despite their extensive use, methodological intricacies were frequently underreported. This paper underscores the necessity for enhanced reporting standards and comprehensive guidelines to optimise the effectiveness and reliability of FGDs in conservation research. By means of critically investigating existing literature, this study contributes critical important insights into the strengths and limitations of FGDs, ultimately advocating for greater methodological rigour and transparency in their application within the realm of conservation science.

Erosion caused by the repeated impact of particles on a substance surface is a usual wear method resulting in gradual and continual loss of objects. It is a crucial problem in several modern industries because their surfaces are frequently subjected to destructive erosive situations. Polymers and their hybrid materials include several applications to be used as a coating in the form of powder for different applications. This review paper aims to provide extensive information on the erosion behavior of thermoset and thermoplastic neat resin and their hybrid materials composites. Focus is specifically paid to highlight the influence of properties of selected materials, impingnation parameters such as incident Angle of erodent, impact velocity of erodent, erodent nature, and the erosion mechanism. The review further extends the information about the erosion techniques and numerical simulation methods used for wear studies of surfaces. An investigation has been carried out for researchers to explore the selection of materials and methods in terms of conditions and parameters to meet the current and future needs and challenges for the protection of surfaces of the advanced industries. During review according to the findings achieved from the literature of the past fifty years, it has been noted that the thermoplastic nature of the composite is a key component to determine the anti-wear properties, the composites with lower glass transition, higher ductility, and greater crystallinity can provide better protection to erosion in advance surface applications.

In order to study the collapse failure of shaft wall of high depth inclined ore-pass under ore impact wear behavior, 25 ore-passes in a deep mine in Yunnan, China were investigated. Considering the ore-pass structural characteristics and the impact wear effect of ore on shaft wall, the shaft wall damage model of high depth inclined ore-pass is constructed based on the contact mechanics theory. Furthermore, No. 1#, 2#, 3# and 9# ore-passes of the mine are taken as examples for analysis, and the three results of theoretical analysis, numerical simulation and engineering case are used for comparison and verification. The shaft wall damage degree is predicted, and the damage mechanism between total shaft wall damage volume Qtol and ore-pass depth H, ore-pass dip angle θ, inclined angle of chute α, shaft diameter D and ore block size P is quantitatively investigated. The results show that the rationality of the proposed model is verified by numerical analysis and field engineering situations. Moreover, the deeper ore-pass depth H, the more shaft wall damage volume Qtol with the increase of collision frequency. Qtol increases exponentially with P and increases gradually with D. With the increase of θ or α, Qtol increases generally first and then decreases. Therefore, Qtol can be effectively reduced by selecting the appropriate structure parameters of ore-pass and adopting the technology of drilling straight ore-pass. This work provides technical support for long period safe operation of high depth inclined ore-pass.

Nano- and microparticles are increasingly widely used in biomedical research and applications, particularly as specific labels and targeted delivery vehicles. Silica has long been considered the best material for such vehicles, but it has some disadvantages limiting its potential, such as the proneness of silica-based carriers to spontaneous drug release. Calcium carbonate (CaCO3) is an emerging alternative, being easily available, cost-effective, biocompatible material with high porosity and surface reactivity, which makes it an attractive choice for targeted drug delivery. CaCO3 particles are used in this field in the form of either bare CaCO3 microbeads or core/shell microparticles representing polymer-coated CaCO3 cores. In addition, they serve as removable templates for obtaining hollow polymer microcapsules. Each of these types of particles has its specific advantages in terms of biomedical applications. CaCO3 microbeads are primarily used due to their capacity for carrying pharmaceutics, whereas core/shell systems ensure better protection of the drug-loaded core from the environment. Hollow polymer capsules are particularly attractive because they can encapsulate large amounts of pharmaceutical agents and can be so designed as to release their contents in the target site in response to specific stimuli. This review focuses first on the chemistry of the CaCO3 cores, core/shell microbeads, and polymer microcapsules. Then, systems using these structures for the delivery of therapeutic agents, including drugs, proteins, and DNA, are outlined. The results of systematic analysis of available data are presented. They show that the encapsulation of various therapeutic agents in CaCO3-based microbeads or polymer microcapsules is a promising technique of drug delivery, especially in cancer therapy, enhancing drug bioavailability and specific targeting of cancer cells while reducing side effects. To date, research in CaCO3-based microparticles and polymer microcapsules assembled on CaCO3 templates has mainly dealt with their properties in vitro, whereas their in vivo behavior still remains poorly studied. However, an enormous potential of these highly biocompatible carriers for in vivo applications is undoubted. This last issue is addressed in depth in the Conclusion and Outlook sections of the review.

Global population is predicted to approach 10 billion by 2050, an increase of over 2 billion from today. To meet the demands of growing, geographically and socio-economically diversified nations, we need to diversity and expand agricultural production. This expansion of agricultural productivity will need to occur under increasing biotic, and environmental constraints driven by climate change. Clustered regularly interspaced short palindromic repeats-site directed nucleases (CRISPR-SDN) and similar genome editing technologies will likely be key enablers to meet future agricultural needs. While the application of CRISPR-Cas9 mediated genome editing has led the way, the use of CRISPR-Cas12a is also increasing significantly for genome engineering of plants. The popularity of the CRISPR-Cas12a, the type V (class-II) system, is gaining momentum because of its versatility and simplified features. These include the use of a small guide RNA devoid of trans-activating crispr RNA (tracrRNA), targeting of T-rich regions of the genome where Cas9 is not suitable for use, RNA processing capability facilitating simpler multiplexing, and its ability to generate double strand breaks (DSB) with staggered ends. Many monocot and dicot species have been successfully edited using this Cas12a system and further research is ongoing to improve its efficiency in plants, including improving the temperature stability of the Cas12a enzyme, identifying new variants of Cas12a or synthetically producing Cas12a with flexible PAM sequences. In this review we provide a comparative survey of CRISPR-Cas12a and Cas9, and provide a perspective on applications of CRISPR-Cas12 in agriculture.

This paper shows the usage of a numerical analysis model which enables the calculation of the life of a railway wheels used for low-floor freight wagons as a function of its primary operating factors, which allows carrying out sensitivity analyses. Low-floor wagons are being increasingly used for combined transport applications and many types of bogies have been proposed in order to constitute the wagons. Due to the uniqueness of this type of wagons, the bogie configurations in terms of wheelbase and axle load have hardly been analyzed so far. The numerical analysis model used addresses the primary challenges that arise in the vehicle – track interaction and establish the relations among them. The main aspects of this model have been described in the paper, which has been later used to calculate the life of an ordinary-diameter wheel for several wheelbase and axle load values. This study has been replicated with reduced-diameter wheels, which are commonly used for low-floor wagons. In this way, it is possible to know the evolution of the life depending on the wheelbase and the axle load. The root causes underlying the observed behaviors can be explained by the entire understanding of the rolling phenomenon provided by the full analytical work.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

In this study, Fe-Mo-B based hardfacing electrodes containing different amounts of Mo were coated on an AISI 1020 steel substrate using the electric arc welding method. The findings show that molybdenum is highly effective on the microstructure and minor changes in the coating composition affect the phases and morphological properties. In the hardness tests, an increase of 73% was achieved in the Fe14Mo2B4 based hardfacing coating compared to the base material and a 30% increase compared to the Fe16B4 based coating. The highest macro hardness value was measured as 56.4 HRC and the highest phase hardness was measured as 3228 HV in the FeMo2B2 phase. The lowest wear rate was measured in the Fe14Mo2B2 based coating. The wear rate of the Fe14Mo2B4 based coating was 8.1 times lower than that of the substrate material and 4.7 times lower than that of the Fe16B4 based coating. According to corrosion test results, the highest corrosion resistance was obtained in Fe16B4 based coating. The current density value of the Fe16B4 based coating was measured to be 13.6 times lower than that of the substrate material.

The vehicles number continuously growing lead to increasingly intense and congested traffic and it will additionally demand the braking system, and drivers behave more aggressively and as result is required that the braking system to be durable and efficient. For this is necessary the study the braking system behavior in conditions of intense and moderate traffic to increase the safety of traffic participants, respectively to demonstrate the need for more frequent replacement of some braking system elements. Thus, on a vehicle were performed a series of successive tests, through which the degree of wear of the brake pads and discs was monitored periodically and as a result the efficiency evolution of the braking system. The tests were carried out both in laboratory (on dynamometer) and in traffic to establish the efficiency of the braking system according to some parameters considered essential. The experimental tests showed that the recommendations regarding the frequency of replacement of brake pads and disks are inconsistent with their actual wear. Therefore, the aim of this paper is the establishment of the braking system efficiency of an auto-vehicle, subject to testing depending on the auto-vehicle mass, travel speed, distance driven, and braking time, based on experimental on stand and in-traffic tests, according the road safety regulations.

The lack of knowledge on the link between the manufacturing process and performances constitutes a major issue of brake lining development. This study focuses on the effect of mixing duration on properties and tribological behavior of organic friction composite materials. The adopted methodology is based on efficient simplified formulations to limit synergic effects by the reduction of number and size distribution of constituents. Microstructural characteristics are analyzed and correlated to thermo physical and mechanical properties. Wear mechanisms and tribological behavior are studied in relation with the given microstructure and material properties. In the elaboration process, mixing duration has an impact on particle distribution and fibre arrangement. Distribution and size of fibre entanglements are found to cluster carbonaceous particles, which creates bulk thermal bridges improving thermal conductivity. Moreover, rockwool fibre arrangements affect density, porosity and thermo-physical properties. In addition, mixing duration disrupts cohesion of fibre bundles with the matrix, affecting compressive modulus and wear behaviour. This microstructural defect fosters an abundant third-body source flow, which results in a high wear flow. Porosities induced by fibre entanglements, presenting large and irregular size and distribution on the friction surface, lead to a low wear resistance and change the stability of friction.

Saliva, as a diagnostic medium, offers a promising alternative to blood by virtue of its non-invasive collection, which enhances patient compliance, especially in paediatric and geriatric populations. In this study, we assessed the utility of saliva as a non-invasive medium for measuring V. cholerae-specific serum antibodies in naturally infected individuals. We tested paired serum and saliva samples obtained from a total of 63 cholera patients enrolled in a cohort study. Vibriocidal antibodies assay (IgM/IgG) as markers for accurate determination was used to determine cholera specific antibody levels. Using receiver operating characteristics (ROC) curve, we found that the best cut-off that maximizes (sensitivity + specificity) is 10 titers. At this saliva titer, the sensitivity is 76.9% (95%CI: 60.9%, 87.7%) and specificity is 80.0% (95%CI: 56.6%, 92.5%). Using Spearman’s correlation coefficient, we also found evidence of a positive correlation between Vibrio Cholerae saliva and serum antibodies (rho=0.66, p<0.001). In conclusion, saliva-based diagnostic cholera tests has high diagnostic accuracy, and would be advantageous, cheaper, and quicker for early diagnosis of severe cholera outcomes.

Citizens face online privacy threats from social media, organisations and governments. Privacy-enhancing tools (PETs) can help people to preserve their privacy, but the uptake of these is limited. We developed a conceptual framework for privacy self-protection, using a classification framework of four distinct privacy threats and our own novel staged model of PET adoption requisites. Through an expert survey (N = 12) and a lay user survey (N = 500), we identified suitable PETs for non-expert users and identified potential barriers to PET adoption. Based on the studies and our theoretical framework, we then developed and implemented a PET decision support tool called PEDRO, and conducted expert evaluations (N = 10).

In the fast-paced internet world that we live in today, internet technologies and tools that enable us to connect online are rapidly changing and improving. To adapt to the changing environment, many game developers are changing their business models to adjust to this online environment by developing games that are centred around online gaming. As such, the internet demands of consumers such as gamers are increasing because of the need for quality internet connection for optimal gameplay. There are too many factors that can affect online gameplay. Moreover, not all gamers are equipped with the network knowledge and skills to diagnose and troubleshoot any internet issues that may arise during their gameplay session. The main contribution of this research was to gather insights from Malaysian broadband internet consumers, mainly from gamers and general users regarding their opinions of their ISP service experience in gaming, general use and service quality. A 1-click solution is presented as a smart autonomous network monitoring tool that can autonomously monitor, diagnose, and troubleshoot network problems with minimal input from the user. This research was conducted using a mixed-mode research methodology where the participants were asked to fill up a questionnaire regarding the user experience of their Internet Service Provider (ISP), and their perception of the 1 click-automated networking tool for their personal use. It is shown that there is a market demand for a 1 click-automated networking tool as gamers and general users both agree that such a tool would be beneficial to them by improving the internet quality of a network.

We developed a novel approach in the field of spatiotemporal modelling, based on the spatialisation of time: the Timescape algorithm. It is especially aimed at sparsely distributed datasets in ecological research, whose spatial and temporal variability is strongly entangled. The algorithm is based on the definition of a spatiotemporal distance that incorporates a causality constraint and that is capable of accommodating the seasonal behaviour of the modelled variable as well. The actual modelling is conducted exploiting any established spatial interpolation technique, substituting the ordinary spatial distance with our Timescape distance, thus sorting, from the same input set of observations, those causally related to each estimated value at a given site and time. The notion of causality is expressed topologically and it has to be tuned for each particular case. The Timescape algorithm originates from the field of stable isotopes spatial modelling (isoscapes), but in principle it can be used to model any real scalar random field distribution.

The social criteria of sustainable development have remained underexplored. Moreover, a large number of green building assessment tool and social sustainability documentations have been developed which, has had a direct impact on social criteria issues, but there seems to be a substantial gap in the study of social criteria in green building assessment tools. In examining the problem facing social sustainability, taking into consideration social sustainability in sustainable development reviews and green building assessment tool towards social aspects. This paper through analysis identified a centripetal conceptual framework composed of seven key components equity, education, participation & control, social cohesion, health & safety, accessibility & satisfaction, and cultural values. The interpretation of the social sustainability in green building assessment tool would impact building practitioners towards implementing social criteria in GBAT. The aim was to identify social categories as well as consider a starting point for the development of an effective social criteria assessment tool for green building.

In this paper, the effect of multi-pass friction stir processing on the mechanical properties of AZ91 alloy has been studied. For the numerical investigation, this process has been simulated with the three-dimensional numerical modeling based on the ABAQUS/Explicit. This simulation involves the Johnson-Cook models for defining the material behavior during this intense plastic deformation and investigating the fracture criterion. The tool plunging and stirring phases in the two-pass process has been simulated. To prevent too much distortion of elements during modeling, the Arbitrary Lagrangian-Eulerian technique for automatically re-meshing of distorted elements has been used. The model was calibrated using the experimental results from the previous works. This model can predict the transient temperature distribution and residual stress field during FSP on AZ91. The results show that the maximum temperature in the advancing-side region is more than that in the retreating-side region. In addition, numerical results show that at the end position of the process, the tool during the lift-up leaves the keyhole region in the compressive stress state. The experimental results investigated the effect of multi-pass FSP on the microstructure, microhardness, tensile and creep properties of AZ91 magnesium alloy. The FSP is performed by applying 50% overlapping. The tensile, and creep tests are conducted at several temperatures from 25 to 210 °C. The optical microscopy and scanning electron micrograph (SEM) were used to study the microstructure of the samples after performing multi-pass friction stir processing. The experimental results indicate that on average, the tensile strength, microhardness, and creep strength of the processed samples increased by about 29, 23, and 38 %, respectively compared to the unprocessed ones.

Macrophages are cells involved in the primary response to debris derived from wear of implanted CoCr alloys. The biocompatibility of wear particles from a high carbon CoCr alloy produced under polarization in physiological hyaluronic acid (HA) solution was evaluated in J774A.1 mouse macrophages cultures. Polarization was applied to mimic the electrical interactions observed in living tissues. Wear tests were performed in a pin-on-disk tribometer integrating an electrochemical cell in phosphate buffer solution (PBS) and in PBS supplemented with 0.3% HA, physiological synovial fluid concentration, used as lubricant solution. Wear particles produced in 0.3% HA solution showed a higher biocompatibility in J774A.1 macrophages in comparison to those elicited by PBS. A considerable improvement in macrophages biocompatibility in the presence of 0.3 % of HA was further observed by the application of polarization at potentials having current densities typical of injured tissues suggesting that polarization produces an effect on the surface of the metallic material that leads to the production of wear particles that are macrophages biocompatible and less cytotoxic. The results showed the convenience to consider electric interactions together with other particles parameters, as are size and composition, to get a better understanding of the biological effects of the wear products.

Abstract: Recent years demonstrate the increased attention to radon from two scientific directions. After neglecting radon as earthquake precursors in 1990-th it becomes again the subject of earthquake-forecast papers discussions due to growing networks of the radon monitoring in different countries, especially, the technologies of real-time radon measurements where the gamma-spectrometers become the leader of interest as the sources of 222Rn identification. The second fast developing direction is including the radon in the Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) models as a source of the boundary layer ionization. And here we encounter with second direction which is not connected with the earthquake forecast problems. It is the role of air ionization by radon as a source of the Global Electric Circuit (GEC) modification. In this publication we try to unite all these problems to present more complex view on radon as important element of our environment.

Many physiotherapy treatments begin with a diagnosis process. The patient describes symptoms, upon which the physiotherapist decides which tests to perform until a final diagnosis is reached. The relationships between the anatomical components are too complex to keep in mind and the possible actions are abundant. A trainee physiotherapist with little experience naively applies multiple tests to reach the root cause of the symptoms, which is a highly inefficient process. This work proposes to assist students in this challenge by presenting three main contributions: (1) A compilation of the neuromuscular system as components of a system in a Model-Based Diagnosis problem; (2) The PhysIt is an AI-based tool that enables an interactive visualization and diagnosis to assist trainee physiotherapists; and (3) An empirical evaluation that comprehends performance analysis and a user study. The performance analysis is based on evaluation of simulated cases and common scenarios taken from anatomy exams. The user study evaluates the efficacy of the system to assist students in the beginning of the clinical studies. The results show that our system significantly decreases the number of candidate diagnoses, without discarding the correct diagnosis, and that students in their clinical studies find PhysIt helpful in the diagnosis process.

Communication pathways are an underestimated source of synthetic particles in the environment. This study investigated the impact of traffic volume on microplastics (MPs) and tire wear particles (TWPs) pollution in road snow. An examination was conducted in a medium-sized city situated in northeastern Poland, known for being one of the cleanest regions in the country. MPs and TWPs were found at all 53 sites, regardless of the intensity of traffic. The average concentration for all samples was 354.72 pcs/L. Statistically significant differences were found between the average values of particles concentration on low, medium, and heavy traffic roads amounted 62.32 pcs/L, 335.97 pcs/L and 792.76 pcs/L respectively. Within all three studied groups of roads, MPs and TWPs with the smallest size, ranging from 50 to 200 μm, were prevalent. In all studied groups of roads, 4 analyzed shapes of particles were found, with irregular fragments being the most abundant form (89.23%). The most frequently recorded color among the collected samples was black (99.85%), and the least frequently recorded was blue, constituting only 0.01%. This study suggests that snow cover on the roads may act like temporary storage of pollutants during winter in the temperate climate zone and after thaw can significantly increase the concentration of MPs and TWPs in surface waters. Possible measures to decrease the release of MPs and TWPs into the environment in the city may include reducing traffic volume and speed, implementing street sweeping, utilizing filtration chambers, and installing stormwater bioretention systems or settling ponds.

Double-walled carbon nanotube-yttria-stabilized ZrO2 nanocomposites are prepared by a mixing route followed by Spark Plasma Sintering. Incorporation of carbon at contents higher than 2 wt.% results in significantly lower friction coefficients, both against alumina and steel balls. Double-walled carbon nanotubes improve wear resistance and reduce friction without severe damage, contrary to multi-walled carbon nanotubes.

Pin-on-plate and pin-on-disk wear tests are typically used for assessing the wear behavior of a given material coupling. Such a behavior is frequently described by a wear coefficient k, which is estimated, according to the Archard’s law, as the ratio between the measured wear volume V and the product of the applied normal force F and the sliding distance s, i.e. k=V/(F s). This study demonstrates that such a relationship is correct for pin-on-plate but not for pin-on-disk, particularly for flat-ended pins. Both analytical and finite element models of the two tests were developed, considering three different distances pin-disk axis. As results, wear volumes, pressure and wear depth maps were examined and compared for the same sliding distance. Though this study is focused only on the initial transient part of the wear tests, some interesting aspects arose: i) rotational effect in pin-on-disk tests affects k estimation, especially when the pin is near to the disk axis; ii) a simple analytical function is defined to correct the wear volume estimation for pin-on-disk tests; iii) due to the different sliding distances of contact points in pin-on-disk tests, pressure redistribution occurs with higher values on the inner side (closer to disk axis); the opposite trend is observed in wear depth maps. From a computational point of view, the pin-on-disk problem, only apparently simple, required very small time increments to correctly describe the circular trajectories of points, with high computational costs. Numerical strategies are currently under investigation to extend the study to the steady state phase of both tests.

The aim of this study was to determine the extent to which the Tyme Wear smart shirt is as reliable and valid in detecting personalized ventilatory thresholds when compared to the Parvo Medics TrueOne 2400. In this validation study, 19 subjects were recruited to conduct two graded exercise test (GXT) trials. Each GXT trial was separated by seven to ten days of rest. During the GXT, gas exchange and heart rate data were collected by the TrueOne 2400 (TRUE) in addition to the ventilation data collected by the Tyme Wear smart shirt (S-PRED). Gas exchange data from TRUE was used to detect VT1 and VT2. TRUE and S-PRED VT1 and VT2 were compared to determine the reliability and validity of the smart shirt. Of the 19 subjects, data from 15 subjects were used during analysis. S-PRED exhibited excellent (ICC > 0.90) reliability for detection of VT1 and VT2 utilizing time point and workload and moderate (0.90 > ICC > 0.75 ) reliability utilizing heart rate. TRUE exhibited excellent reliability for detection of VT1 and VT2 utilizing time point, workload, and heart rate. When compared to TRUE, S-PRED appears to underestimate the VT1 workload (p > 0.05) across both trials and heart rate (p < 0.05) for trial 1. However, S-PRED appears to underestimate VT2 workload (p < 0.05) and heart rate (p < 0.05) across both trials. The result from this study suggests that the Tyme Wear smart shirt is less valid but is comparable in reliability when compared to the gold standard. Moreover, despite the underestimation of S-PRED VT1 and VT2, the S-PRED detected personalized ventilatory thresholds will provide an adequate training workload for most individuals. In conclusion, the Tyme Wear smart shirt provides easily accessible testing to establish threshold-guided training zones but does not devalue the long-standing laboratory equivalent.

It has been known that the performance of the High-Pressure Grinding Rolls (HPGR) varies as a function of method used to confine laterally the rolls, their diameter/length (aspect) ratio as well as their condition, if new or worn. However, quantifying these effects through direct experimentation in machines with reasonably large dimensions is not straightforward given the challenge, among others, of guaranteeing that the feed material remains unchanged. The present work couples the discrete element method (DEM) to multibody dynamics (MBD) and a novel particle replacement model (PRM) to simulate the performance of pilot-scale HPGRs grinding pellet feed. It shows that rotating side plates, in particular when fitted with studs, allow reaching more uniform forces along the bed, which also translates in a more constant product size along the rolls as well as higher throughput. It also shows that the edge effect is relatively constant with roll length, leading to substantially larger proportional edge regions for high-aspect ratio rolls. On the other hand, the product from the center region of such rolls was found to be finer when pressed at identical specific forces. Finally, rolls were found to have higher throughput, but generate a coarser product when worn following the commonly observed trapezoidal profile. The approach used in industry to compensate for roller wear by increasing the specific force and roll speed has then been demonstrated to be effective to maintain and potentially even increase product fineness and throughput, as long as the minimum safety gap is not reached.