Total ankle replacement (TAR) implants are an effective option to restore the range of motion of the ankle joint for arthritic patients. An effective tool for analyzing these implants’ mechanical performance and longevity in-silico is finite element analysis (FEA). ABAQUS FEA was used to statically analyze the von Mises stress and contact pressure on the articulating surface of the bearing component in two newly installed fixed-bearing total ankle replacement implants (the Wright Medical INBONE II and the Exactech Vantage). This ultra-high molecular weight polyethylene (UHMWPE) bearing commonly fails and is the cause for surgeon revisions. Six different FEA models for various gait percentages during stance (10%-60%) were created. They varied in magnitude of the compressive load and the ankle dorsiflexion/plantarflexion angle. The results indicated that the von Mises stress and contact pressure distributions increased as compressive load increased, and the largest magnitudes occurred at high dorsiflexion angles (15-30°). High magnitudes occurred in regions where the thickness of the bearing was the least. Additionally, high contact pressures were examined in areas near the talar component's edge or at the bearing's edges. To the author’s knowledge, this is the first study available to the research community that analyzes the Vantage implant with FEA. This study lays an essential foundation for future researchers in presenting a thorough literature review of TAR and methods for a simple FEA model setup. This study provides valuable information that can be beneficial to medical company designers and orthopedic surgeons in understanding the stress response and contact pressure of TAR implants during use.

Total hip arthroplasty is a complex procedure. The achievements of implantology enabled the development of a faithful representation of hip joint physiology as well as the production of materials that can successfully replace damaged natural tissues. A very important issue is the correct selection of the geometry of the endoprosthesis adequate to the load of the joint. Materials used for endoprosthesis are a metal head and a polymer cup (e.g. PE-UHMW). The main interactions in the endoprosthesis are friction and surface pressure, which must be limited, exceeding them causes the destruction of the biomechanical system - plastic deformation of the polymer and the formation of too large and unacceptable radial clearances. Based on the author's developed calculation method of hip joint endoprosthesis contact parameters, the impact on maximum contact pressure and the angle of contact of the joint load was estimated depending on the diameter of the endoprosthesis and radial clearance. The correctness of changing the values of maximum contact pressure from the mentioned parameters was determined. Correspondingly: an increase in joint load causes a linear increase in the maximum contact pressure; increasing the diameter of the endoprosthesis head - their non-linear decrease, and increasing radial clearance - their increase

Mass transfer restrictions of scaffolds are currently hindering the development of three-dimensional (3D), clinically viable, and tissue engineered constructs. For this situation, a 3D poly(lactide-co-glycolide)/hydroxyapatite porous scaffold, which was much favorable for transfer of nutrients to and waste products from the cells in the pores, was developed in this study. The 3D scaffold had an innovative structure, including macropores with diameters of 300−450 μm for cell ingrowth and microchannels with diameters of 2−4 μm for nutrition and waste exchange. The mechanical strength in wet state was strong enough to offer the structural support. The typical structure was more beneficial for the attachment, proliferation, and differentiation of rabbit bone marrow mesenchymal stem cells (rBMSCs). The alkaline phosphatase (ALP) activity and calcium (Ca) deposition were evaluated on the differentiation of rBMSCs, and the results indicated that the microchannel structure was very favorable for differentiating rBMSCs into maturing osteoblasts. For repairing rabbit radius defects in vivo, there was rapid healing in the defects treated with the 3D porous scaffold with microchannels, where the bridging by a large bony callus was observed at 12 weeks post-surgery. Based on the results, the 3D porous scaffold with microchannels was a promising candidate for bone defect repair.

After a long limbo, RNA has gained its credibility as a druggable target, fully earning its de-served role in the next-generation area of pharmaceutical R&D. We have recently probed the Trans-Activation Response element (TAR), a RNA stem–bulge–loop domain of the HIV-1 genome with bis-3-chloropiperidines (B-CePs), and revealed the compounds unique behavior in stabiliz-ing TAR structure, thus impairing in vitro the chaperone activity of the HIV-1 nucleocapsid (NC) protein. Seeking to elucidate the determinants of B-CePs inhibition, we have further characterized here their effects on the target TAR and its NC recognition, while developing quantitative analyti-cal approaches for the study of multicomponent RNA-based interactions.

A proportion of osteoarthritis (OA) patients are unsatisfied with post-operative outcomes following total joint replacement surgery (TJR), with insufficient pain relief or poor functional improvement. Predicting those will have poor outcomes would be beneficial for patients and clinicians. The aim of this study was to determine the relationship between baseline anthropometric data and the concentration of pre-operative serum and peri-operative synovial fluid (SF) cytokines with 7-month post-operative outcomes in a cohort of knee and hip OA patients. 160 OA patients were recruited who were scheduled for TJR. The concentration of 24 cytokines were measured in blood and SF by multiplex assay. EQ5Dindex health status was assessed pre-operatively and at 7-months post-operatively. 13% of patients were identified as non-responders based on EQ5Dindex. Compared to responders, non-responders were of higher BMI, had greater waist and hip circumference and had higher levels of SF leptin but lower levels of SF Resistin (p<0.05). Linear regression analysis found a significant relationship between pre-operative body weight and post-operative response (ΔEQ5Dindex; r=0.222, p=0.049). The combination of body weight with SF amphiregulin and SF IL-6 provided an improved predictive model of post-operative response (r=0.470, p=0.035).

Purpose: Cardiovascular disease (CVD) is a major risk factor for mortality in patients with osteoarthritis, and comorbidities increase postoperative complications after total knee arthroplasty (TKA). Arteriosclerosis plays a major role in hemodynamic dysfunction and CVD; however, arteriosclerosis has not been preoperatively evaluated before TKA using the cardio–ankle vascular index (CAVI). In this study, we evaluated the degree of preoperative arteriosclerosis using the CAVI in patients undergoing TKA, as well as its correlations with several preoperative patient factors. Methods: Arteriosclerosis was evaluated in 209 consecutive patients (251 knees) with osteoarthritis who underwent TKA at our institution between May 2011 and June 2022. The CAVI was measured in the supine position 1 day before TKA, and the correlations between the CAVI and several clinical factors were analyzed. A p value of <0.05 was considered statistically significant. Results: The CAVI was normal in 62 knees (25%), borderline in 71 knees (28%), and abnormal in 118 knees (47%). Univariate analysis revealed a moderate positive correlation between preoperative CAVI and age (r = 0.451, p < 0.001) and a weak negative correlation between preoperative CAVI and body weight (r = −0.306, p < 0.001) and body mass index (BMI) (r = −0.319, p < 0.001). Multivariate analysis showed that age (β = 0.349, p < 0.001) and BMI (β = −0.235, p < 0.001) were significantly correlated with preoperative CAVI. Conclusion: Arteriosclerosis should be carefully managed intraoperatively and postoperatively in patients with osteoarthritis undergoing TKA, particularly in older patients and patients with a low BMI.

Introduction: These days, obesity is considered an important factor for many medical problems such as diabetes mellitus, cardiovascular diseases and joint degeneration. Obesity is one of the leading causes of osteoarthritis and the need for arthroplasty. We aim to study the effect of obesity and the duration of knee replacement surgery.Method: A cross-sectional study was conducted at the orthopedic department between February 2023 and July 2023. We had 68 patients who underwent total knee replacement surgery. Variables like age, gender, smoking history, ASA grade, BMI, and side of injury (unilateral or bilateral) were studied.Results: Out of 68 patients, we had 37 (54.4 %) of patients were female. The most common age group was 44- 54 years. 60.3 % of patients were non-smokers. We had 50 patients with unilateral injury and the rest were bilateral. ASA grade II (51 patients) were more than ASA grade I (17 patients). In this study, 41 patients were obese and the duration for total knee replacement was 90 - 120 minutes, in contrast to overweight patients (75 – 90 minutes) and normal patients (60-75 minutes).Conclusion:We found a significant correlation between BMI and the duration of total knee replacement surgery. The time could be doubled if the arthroplasty was bilateral.

Diabetes markedly increases susceptibility to adverse cardiovascular events, including heart failure (HF), leading to heightened morbidity and mortality rates. Elevated levels of natriuretic peptides (NPs), notably B-type natriuretic peptide (BNP) and N-terminal-proBNP (NT-proBNP), correlate with cardiac structural and functional abnormalities, aiding in risk stratification and treatment strategies in individuals with diabetes. This article reviews the intricate relationship between diabetes and HF, emphasizing the role of NPs in risk assessment and guiding therapeutic strategies, particularly in individuals with type 2 diabetes mellitus (T2DM). It also explores the challenges and prospects of natriuretic peptide-guided therapy in managing cardiovascular risk in patients with diabetes.

. This article presents, for the first time, the kinetics and the general features of a photopolymerization system (under visible light) G1/ Iodonium/ TEA/gold chloride (or A/B/N/G), having initial concentrations of A0, B0, N0 and G0, based on the proposed mechanism of Tar et al. Analytic formulas are developed to explore the new features including: (i) both FRP efficacy and the production of nanogold (NG) are proportional to the relative concentration ratios of (A0+B0+N0)/G0, which may be optimized for maximum efficacy; (ii) the two competing procedure of NG production and efficacy of free radical photopolymerization (FRP) can be tailored for optimal system with nanogold in the polymer matrix;(ii) the FRP efficacy is contributed by 3 components: the coupling of the excited state of copper complex (T) with the radicals (R and S) produced by the iodonium and the amine; (iii) the production of NG is contributed by 2 components: the coupling of T and radical (S) with gold ion; (iv) NG production has a transient state value which is an increasing function of light intensity and the combined concentration ratio [(A0/G0)+(N0/(K'M0). whereas it has a steady-state independent to the light intensity.

Foot pain related to the plantar fascia is common in adults regardless of athletic background. Many pathologies can lead to the diagnosis of plantar enthesopathy, but the most relevant to this case study is related to structural defects within the plantar fascia. Due to the variety and sometimes unclear etiology of plantar fasciosis, no single standard of care treatment protocol is recognized. Often, patients receive NSAIDs, night splints, taping, physical therapy, foot orthosis, and extracorporeal shock wave therapies. This study presents Wharton Jelly (WJ) tissue allografts as an additional intervention for patients who fail standard-care treatments. WJ allografts are applied to supplement connective tissue defects directly, unlike other therapies, which aim to reduce swelling and symptomatic pain. This retrospective study includes seven patients who have previously failed standard-of-care treatment. Each received extracorporeal pulse-activated therapy (EPAT), WJ, laser therapy, and an orthotic. Patient progress was tracked using a visual analog scale, 0-10 scoring, reported by the patient at the initial visit and approximately thirteen weeks following, reporting an average improvement of 50%. The study's limitations include a small cohort size and a non-blinded retrospective design. These promising results provide evidence for a more extensive, randomized study to define dosage protocols further and confirm safety and efficacy.

Weight-bearing computed tomography (WBCT) enables acquisition of three dimensional bony structure images in a physiological weight-bearing position, which is fundamental in under-standing the pathologic lesions and deformities of the ankle joint. Over the past decade, re-searchers focused on validating and developing WBCT measurements, which has significantly enhanced our knowledge of common foot and ankle disease. Consequently, understanding the application of WBCT in clinical practice is becoming more important to produce improved out-comes in the treatment of disease around the ankle joint. This review will describe an overview of what is currently being evaluated in the foot and ankle surgery using WBCT and where the course of research will be heading in the future.

HIV-1 Tat protein interacts with TAR RNA and recruits CDK9/cyclin T1 and other host factors to induce HIV-1 transcription. Thus Tat-TAR RNA interaction, which is unique for HIV-1, represents an attractive target for anti-HIV-1 therapeutics. To target Tat-TAR RNA interaction, we used a crystal structure of TAR RNA with acetylpromazine bound to the bulge of TAR RNA, to dock compounds from Enamine database containing 1.6 million individual compounds. Docking identified 173 compounds that were analyzed for the inhibition of HIV-1 infection. Top ten inhibitory compounds with IC50 ≤ 6 µM were selected and the three least toxic compounds, T6780107 (IC50=2.97 μM), T0516-4834 (IC50=0.2 μM) and T5628834 (IC50=3.46 μM), were further tested for HIV-1 transcription inhibition. Only T0516-4834 compound showed selective inhibition of Tat-induced HIV-1 transcription, whereas T6780107 compound inhibited equally basal and Tat-induced transcription and T5628834 compound only inhibited basal HIV-1 transcription. The T0516-4834 compound also showed strongest inhibition of HIV-1 gag RNA expression and p24 production in CEM T cells infected with HIV-1 IIIB. Of the three compounds, only the T0516-4834 compound disrupted Tat-TAR RNA interaction indicating that it might target TAR RNA. Also, of the three tested compounds, T5628834 but not T6780107 or T0516-4834 disrupted Tat-CDK9/cyclin T1 interaction. Taken together, our study identified novel compound T0516-4834 that disrupted Tat-TAR RNA interaction and inhibited Tat-induced transcription and HIV-1 infection suggesting that this compound might serve as a new lead for anti-HIV-1 therapeutics.

Ankle sprains are the most frequently occurring musculoskeletal injuries among recreational athletes. Ankle support through bandages following the initial orthotic treatment might be beneficial for rehabilitation purposes. Since hardly any study has investigated the impact of bandages in the acute phase of ankle sprains, our study examined the immediate effects of wearing an ankle bandage on fine coordination, proprioception, and motor performance in subjects five weeks after an acute ankle injury. In total, 70 subjects with acute unilateral supination trauma were tested. All subjects completed several rating questionnaires and biomechanical investigations, including a fine coordination and proprioception test, single leg stances, the Y-Balance test and gait analysis. All biomechanical investigations were conducted for the subject's injured leg with and without a bandage (MalleoTrain® Bauerfeind AG) and the healthy leg. Subjects reported moderate to strong improvements in ankle stability and pain when wearing the bandage. Wearing the bandage significantly normalized subjects’ single leg stance performance, as well as the stance phase duration, and the vertical ground reaction forces during walking. However, the bandage did not have a clear effect on fine coordination and proprioception. Wearing a bandage in the acute phase of an ankle sprain may immediately improve motor performance, including standing and walking.

The aim of the study was the comparison of conventional sintering versus additive manufacturing techniques for β-TCP bioceramics, focusing on mechanical properties and biocompatibility. A "critical" bone defect requires surgical intervention beyond simple stabilization. Autologous bone grafting is the gold standard treatment for such defects but it has its limitations. Alloplastic bone grafting using synthetic materials is becoming increasingly popular. The use of bone graft substitutes has increased significantly and current research was focused on optimizing these substitutes, whereas this study compares two existing manufacturing techniques and the thereby produced β-TCP implants. The 3D-printed β-TCP hybrid structure implant was fabricated using two components, a column structure and a freeze-foam, which were sintered together. The conventionally manufactured ceramics were made by pouring. Both scaffolds were characterized according to porosity, mechanical properties and biocompatibility. The hybrid structure had a total porosity of 74.4 ± 0.5%. Microporous β-TCP implants had a porosity of 43.5 ± 2.4%, while macroporous β-TCP implants had a porosity of 61.81%. Mechanical testing revealed that the hybrid structure had a compressive strength of 10.4 ± 6 MPa, significantly lower than the microporous β-TCP implant’s with 32.9 ± 8.7 MPa. Biocompatibility evaluations showed a steady increase in cell proliferation over time for all β-TCP implants, with minimal cytotoxicity. This study provides valuable insight into the potential of additive manufacturing for β-TCP bioceramics in the treatment of bone defects.

Renal replacement therapy (RRT), widely used in the treatment of renal injury in the course of sepsis, aims to eliminate the toxins and proinflammatory cytokines, involved in the pathomechanism underlying septic shock. Dialysis filters characterised by a high adsorption potential for cytokines in RRT when septic renal injury is the case. It is of key importance in the antibiotics treatment of sepsis to achieve desired values of PK/PD indices. Continuous renal replacement therapy (CRRT) may affect antimicrobial clearance, increasing their elimination in some cases. The aim of this study was to determine the degree of adsorption for linezolid, on three different types of filters used in CRRT. In our in vitro study a continuous veno-venous hemofiltration (CVVH) was conducted using 3 types of filters: polysulfone (PS), polyethyleneimine-treated polyacrylonitrile (PAN PEI) and non-PEI-treated polyacrylonitrile (PAN) filters. Each type of filter was used in 3 CVVH cycles, involving the use of 600 mg of linezolid dissolved in 700 ml of bovine blood or in 700 ml of 0.9% NaCl. In each case the total volume of the obtained solution was 1000 ml. Blood samples, at particular time points, were collected in order to measure drug concentration. The differences in mean drug/NaCl adsorption and drug/ blood adsorption were determined using one-way ANOVA with multiple comparisons by Tukey post-hoc test. A p-value of < 0.05 was considered to be significant. A significant adsorption of linezolid was found for PAN PEI filter, both in samples obtained from bovine blood and 0.9% NaCl solutions, at the endpoint. No significant adsorption was demonstrated on PAN or PS filters. There is a need for in vivo research to confirm the effect of filter type on linezolid concentration in patients undergoing CRRT.

This paper presents a study on developing of a new exoskeleton for ankle joint rehabilitation with three degrees of freedom (3 DOFs). The primary attention is paid to the process of designing and modelling the device aimed at restoring the lost functions of joint mobility. The authors carried out a complex analysis of the functional requirements of the exoskeleton based on the research of potential user’s needs, which allowed them to develop a conceptual model of the proposed de-vice. In this study, a prototype of the exoskeleton is designed using modern additive technolo-gies. A prototype of the proposed device underwent virtual testing in conditions maximally close to the real one, which confirmed its effectiveness and comfort of use. The main results of the work indicate the promising potential of the proposed solution for application in rehabilitation practice, especially for patients with ankle joint injuries and diseases.

(1) Background: The rapid development of information technology has changed the traditional concept of space, gradually shifting the "container space" to the "relational space" . The constraints of geographical spatial elements are diminishing, and the theory of virtual agglomeration is gaining attention. (2) Methods: In this study, we constructed an evaluation system for virtual agglomeration, comprising four primary indicators: virtual infrastructure level, virtual output level, virtual input level, and virtual service level. The TOPSIS method was used to calculate the virtual agglomeration level for each province, and the DEA-Malmquist method was employed to measure provincial total factor productivity (TFP) in China. Using panel data from 30 provincial regions in China from 2013 to 2021, we examined the mechanism and impact path of virtual agglomeration on TFP. (3) Result: There is an inverted U-shaped relationship between virtual agglomeration and TFP in China. The overall development level of virtual agglomeration is relatively low, within the range where the marginal effect of virtual agglomeration on TFP is positive but diminishing, indicating significant potential for further development. The impact of virtual agglomeration on TFP is stronger in the Yangtze River Economic Belt compared to non-Yangtze River areas, and the highest stable point of TFP is higher in central provinces than in eastern and western provinces. (4) Conclusions: This study provides a theoretical basis and practical reference for improving the level of virtual agglomeration.

BACKGROUND Detecting total cholesterol in dried blood spots could aid in identifying individuals with a high likelihood of familial hypercholesterolemia and could be used as a screening measure. This study aims to assess the diagnostic accuracy of dried blood spots on Whatman 903 paper cards using a manual enzymatic technique. METHODS A total of 394 samples collected as serum and dried blood spots were compared. Cholesterol was determined in serum using the automated reference method, while cholesterol on paper was measured using a manual enzymatic method. Within- and between-day diagnostic variability were analyzed. The correlation between both methods was assessed using Passing-Bablok regression and Bland-Altman plot. Internal validation of our correlation formula was performed on 149 samples, along with external validation of the formula proposed by Corso et al. RESULTS The within- and between-day coefficient of variation was found to be lower than 10.14% and 14.09%, respectively. Method comparison yielded an area under the curve of 0.976, with a standard error of 0.009. Passing-Bablok regression indicated a precision of 0.803 and an accuracy of 0.96. Internal validation precision was measured at 0.716. Regarding internal validation, calculated cholesterol with our regression line did not differ from serum cholesterol analysis, while significant differences were observed in calculated cholesterol levels using the external formula. CONCLUSIONS Total cholesterol analysis in dot blood spots demonstrates high precision and reproducibility. This method reliably enables the incorporation of this biological marker into neonatal screening for familial hypercholesterolemia detection.

The EU has set the ambitious target of raising the share of EU energy consumption produced from renewable resources to 32% by 2030 with a target of climate neutrality by 2050. The aim of this paper is to assess the role of biomass usage in the context of these targets. The paper identifies progress made between 2013–2022 by focusing on a selection of EU countries. The largest bio-energy increments of 130PJ, 77PJ and 60PJ were reported for Poland, Sweden, and the Nether-lands. This study valuates the crucial role in co-generation and heat in EU regions, with biomass usage between 55-80% of the combined heat and power (CHP) energy in Nordic countries. The future perspectives for bioenergy based on EU policies, biomass resources and technical issues were addressed. The EU possess around 9% of the global biomass supply, ensuring a certain level of biomass resource dependence. Thus, the biomass usage demand in energy production, non-energy sectors and transport is expected to rise leading to increments of 13%-76% on biomass imports. It appears that bioenergy development is mostly limited by economic issues and uneven support for bioenergy in different EU countries as well as environmental issues. The study shows a promising and sustainable potential of bioenergy in the EU as a renewable energy source while minimizing negative impacts on the environment and the economy. By 2050, liquid biofuels are likely to be increasingly used in the transport sector. Non-energy sector usage of biomass is still in an early stage of development, except for the pulp and paper industry, and significant use of biomass in non-energy sectors seems unlikely in the near future.

Ultrasound imaging is a vital imaging tool in musculoskeletal medicine, with the number of publications on ultrasound-guided surgery increasing in recent years. However, ultrasound imaging has drawbacks, such as operator dependency and image obscurity. Artificial Intelligence (AI) and Deep Learning (DL), a subset of AI, can address these issues. DL methods, including segmentation, detection, and localization of target tissues and medical instruments, potentially allow physicians and surgeons to perform ultrasound-guided procedures more accurately and efficiently. This review summarizes recent advances in ultrasound-guided procedures for musculoskeletal diseases and provides a comprehensive overview of the utilization of AI/DL in ultrasound for musculoskeletal medicine, particularly focusing on ultrasound-guided surgery.

: Organic poultry need high-quality proteins in their diet. The EU’s organic regulation forbids synthetic amino acids; therefore, soybean, with its balanced essential amino acid content, has become the most used protein source, though much of it is imported from non-EU countries. Soybean, however, has some important problems related to sustainability and crop competition; therefore, it must be substituted with a high-protein-value alternative such as insect meal. In this study, 900 Aviagen Savanna broilers were reared using three different organic diets. The diets used the following as protein feed material: soybean only (S100), 50% black soldier fly larvae meal (BSL) and 50% soybean (BSL50), and 100% BSL only (BSL100). Broiler performance, welfare, and fatty acids (FA) in the thigh and breast were analyzed. BSL50 and BSL100 negatively affected growth performance, while BSL100 worsened all of the market-related measures of performance. Meat quality was worse in BSL50 and BSL100, with a significant increase in saturated FA (SFA) and a corresponding decrease in polyunsaturated FA (PUFA). Among SFA, lauric acid (C12:0) more notably increased. The increase in SFA represents a negative aspect of BSL meal inclusion, namely the production of lauric acid; however, this trend could have a beneficial effect, which will be more deeply explored with regard to its impact on animal and human health.

Ankle sprains are exceedingly common injuries in both athletes and general population. They account for 10 to 30% of all sports injuries. Although the vast majority of lateral ankle ligamentous injuries respond successfully to conservative management, the absolute number of those that progress to chronic lateral ankle instability (CLAI) remains considerably important. This condition is characterized by persistent symptoms and may be associated with short-term and long-term complications and functional deficits. There is still a lack of ideal postoperative management of CLAI patients. Furthermore, an evidence-based rehabilitation phasing does not exist and most of the published studies regarding this subject suggest some protocols based on a wide variety of functional assessment scores and other modalities which are not accurate enough. Moreover, the literature that assesses the ability to return to work (RTW) and return to sport (RTS) in general population and athletes operated for CLAI shows most commonly aggregated results with global rates of RTW or RTS without describing a detailed timeline based on the readiness of patients to return to each level of activity. Although stress radiographs and MRI have been assessed as potential tools to improve postoperative management of CLAI patients, the first modality is limited by its low sensitivity to detect laxity and the second one by its static character and its inability to predict the healing process phase nor the mechanical properties of the repaired/reconstructed ligaments. Bioelectrical impedance, mechanical impedance and near-infrared spectroscopy are non-invasive methods of measurement that could be potential assessment tools to help surgeons improve the postoperative management of patients after CLAI surgery.

Functional ankle instability (FAI) results from multiple ankle sprains, causing a perceived sense of joint instability due to muscle and ligament imbalances. Neuromuscular training (NMT) is employed to enhance ankle stability in individuals with FAI. The study included 24 male university students with FAI, who underwent ankle NMT on three surfaces. OpenSim musculoskeletal model analyzed the effects on ankle muscle activity, kinetics, and kinematics. Utilizing repeated measures analysis of variance (ANOVA) and one-dimensional statistical non-parametric mapping (SNPM1d) to identify distinctions between training surfaces. NMT on foam cushion (FC) significantly enhanced tibialis anterior (TA) and gastrocnemius medial (GM) activation during walking compared to level-ground (LG) and artificial turf (AT) (p&lt;0.05). However, no differences observed for peroneus longus (PL), gastrocnemius lateral (GL), and peak ankle plantarflexion (PF). During jogging and fast running, post FC training increased TA, PL, GM, GL activation, and peak ankle PF moment (p&lt;0.05). Additionally, post FC training, subtalar mobility was significantly reduced (p&lt;0.05), and ankle joints exhibited greater dorsiflexion (DF) angles during jogging and fast running (p&lt;0.05). Consequently, selecting FC for short-term ankle NMT proves more advantageous in enhancing ankle stability among individuals with FAI, yielding a more positive impact on FAI improvement.

This research focuses on the development of a foot-worn device to assist individuals with limited mobility in walking. The device aims to reduce the risk of accidents by closely moni-toring the wearer's movements and detecting potential hazards. It incorporates sensors, in-cluding the MPU6050 gyro sensor and KY-031 vibration sensor, to track the wearer's walking behavior. In case of abnormalities, such as falls, the device triggers an auditory alert and noti-fies the caregiver via LINE Notify. The system is controlled by the Node MCU ESP8266, enabling seamless integration with the Internet of Things (IoT). The objective of this study is to design an IoT system for medical assistance. The researchers created a prototype of a smart ankle device capable of detecting falls and sending notifications to the user's smartphone. The effectiveness of the notification system was evaluated using the Line Notify application. Re-sults demonstrated a successful detection of falls in 48 out of 50 trials, with two instances of false alarms during normal walking. The overall efficiency of the smart ankle device was 98%. In summary, the proposed smart ankle device demonstrates promising potential for var-ious applications in fall detection and safety alert systems. Further improvements and collab-orations with healthcare experts are recommended to enhance its performance and make it commercially viable. The device's connectivity and responsiveness to IoT systems are vital aspects to be considered. Future research should aim to develop additional features in collab-oration with physiotherapists and healthcare professionals to meet user requirements. The de-vice holds significant benefits in terms of fall detection and safety alerts, and efforts should be made to enhance its durability, robustness, and commercialization prospects.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

In this study, changes in the microstructure of coal tar pitch during successive processes, including pyrolysis, polycondensation, and crystallization, were examined in connection with the resulting variations in structure factors, as measured by XRD analysis, and functional groups, as confirmed by FTIR spectroscopy. To this end, four zones were defined based on variations in crystallinity, which were indicated by d002 and Lc. Each zone was further characterized by interpreting crystallinity development in relation to changes in functional groups and specimen height. At around 400 °C, polycondensation occurred as the C-Har and C-Hal peaks decreased in intensity. These peak reductions coincided with the formation of mesophase spheres, resulting in enhanced crystallinity. Subsequently, at around 500 °C, the peak intensity of C-H and COOH decreased, which was attributed to the release of large amounts of gasses. This led to sharp volume changes and a temporary reduction in crystallinity. All these results suggest that changes in the functional groups of coal tar pitch at lower temperatures (600 °C or less) during the carbonization process are closely associated with variations in its crystallinity. The major findings of the present study provide valuable insights for designing highly effective processes in the manufacturing of synthetic graphite blocks using CTP as a binder material, including by selecting appropriate temperature ranges to minimize volume expansion and crystallinity degradation and determining the lowest possible carbonization temperature to ensure adequate binder strength.

Background - Compared to the da Vinci platform, there is limited experience with the Hugo RAS platform for colorectal surgery in Europe. This difference is especially notable when considering a single complex procedure, such as total colectomy. Aim - To demonstrate the feasibility and safety of using the Hugo RAS for assisted total colectomy. Clinical case- Female patient: eighteen-year-old with Familial Adenomatous Polyposis (FAP). Her IBM was 19. She underwent a total colectomy with ileorectal anastomosis using the Hugo RAS platform. The procedure took 230 minutes and had no complications. The postoperative period was uneventful. She was discharged from the hospital on the third postoperative day. Conclusion - The Hugo RAS platform is one of the emergent minimally invasive robotic platforms that can be used even in total colectomy if the proper patient selection is made. The placement choice of arms and trocars was crucial to obtain a similar operative time of the single laparoscopic approach. The certification of Hugo’s new instruments, such as energy devices and staplers, will make this platform even more competitive.

Aortic stenosis (AS) is a prevalent valvular disorder that often requires surgical aortic valve replacement (SAVR) to alleviate symptoms and improve survival. However, the selection of an appropriate prosthetic valve size is crucial to avoid patient-prosthesis mismatch (PPM), which can lead to suboptimal hemodynamic outcomes. Von Willebrand factor (VWF), a key component of hemostasis, has been shown to be altered in AS patients and may contribute to the hemostatic imbalance observed following valve replacement. This prospective study aimed to investigate the impact of PPM on postprocedural VWF levels in patients undergoing SAVR for severe AS. The study included 31 consecutive patients diagnosed with severe AS who underwent SAVR. By focusing on the relationship between PPM and VWF dynamics, this study sought to provide valuable insights into the potential role of VWF as a marker for hemostatic changes associated with PPM, ultimately informing strategies for optimal valve selection and perioperative management to minimize complications.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

Capabilities of the Attenuated Total Reflection (ATR) at THz wavelengths for increased sub-surface depth characterisation of (bio-)materials is presented. The penetration depth of a THz evanescent wave in biological samples is dependent on the wavelength and temperature and can reach 0.1-0.5 mm depth due to strong refractive index change ∼0.4 of the ice-water transition; this is quite significant and important when studying biological samples. Technical challenges are discussed when using ATR for uneven, heterogeneous, high refractive index samples with possibility of frustrated total internal reflection (a breakdown of the ATR reflection-mode into transmission-mode). Local field enhancements at the interface are discussed with numerical/analytical examples. Maxwell’s scaling was used to model behaviour of absorber-scatterer inside materials at the interface with ATR prism for realistic complex refractive indices of bio-materials. Modality of ATR with polarisation analysis is proposed and its principle illustrated, opening an invitation for its experimental validation. The sensitivity of the polarised ATR mode to the refractive index between the sample and ATR prism is revealed. Design principles of polarisation active optical elements and spectral filters are outlined. The results and concepts are based on experiments carried out at the THz beamline of the Australian Synchrotron.

Background. To prospectively evaluate the reliability of a portable optical scanner compared to the water displacement technique for volumetric measurements of the foot and ankle, and to compare the acquisition time associated with these two methods. Methods. Foot volume was measured in 29 healthy volunteers (58 feet, 24 female/5 male) by a 3D scanner (UPOD-S 3D Laser Full-Foot Scanner ®) and by water-displacement volumetry. Measurements were performed on both feet, up to a height of 10 cm above the ground. The acquisition time for each method was evaluated. Kolmogorov-Smirnov test, Lin's Concordance Correlation Coefficient, and a Student’s t-test were performed. Results: Mean foot volume was 869.7+/-165.1cm3 (3D scanner) versus 867.9+/-155.4cm3 (water-displacement volumetry) (p <10-5). Concordance of measurements was 0.93, indicative of a high correlation between the two techniques. Volumes were 47.8 cm3 lower when using the 3D scanner versus water volumetry. After statistically correcting this underestimation, the concordance was improved (0.98, residual bias = -0.03 +/- 35.1 cm3). Mean examination time was 4.2 +/-1.7 min (3D optical scanner) versus 11.1 +/-2.9 min (water volumeter) (p<10-4). Conclusion: Ankle/foot volumetric measurements performed using this portable 3D scanner are reliable and fast, and can be used in clinical practice and research.

Liquorpheresis (CSF filtration) comprises a therapeutical approach that has been proposed to treat several neurological conditions where antibodies, inflammatory mediators or abnormal peptides are the cause or play an important role in the pathogenesis of the disease. CSF replacement may be an alternative approach not explored so far. Here, we review previous experiences in the use of liquorpheresis in autoimmune and degenerative neurological diseases. Then we describe previous developments and provide some new technical innovations in order to design bidirectional CSF shunting systems. These systems can be complemented either with a deposit of artificial CSF or with a CSF filter, allowing CSF replacement or liquorpheresis respectively. Both options would lead to mechanical dilution of the patient’s CSF.

This paper aimed to evaluate the growth, gas exchange and Chl a fluorescence in ipê-rosa seedlings, subjected to levels of 100, 75, 50 and 25% of water replacement (LWR), in a greenhouse. The morphometric variables of plant height, diameter at stem height, number of leaves and leaflets, root length and volume, plant dry mass and leaf area were evaluated. The potential evapotranspiration of seedlings (ETc) was obtained using direct weighing, considering as a reference the water replacement of 100% of the mass variation between subsequent days; the cultivation coefficients (kc) were obtained by the ratio between ETc and the reference evapotranspiration (ETo) obtained by the Penman-Montheit FAO-56 method. Biomass and evapotranspiration data were combined to determine water sensitivity. Diurnal fluxes of gas exchange (net photosynthesis rate, transpiration rate, stomatal conductance, internal and atmospheric carbon ratio, water use efficiency and leaf temperature) and Chl a fluorescence (Fv/Fm, ΦPSII, ETR, Fv’/Fm’, NPQ and qL) were evaluated. Water restriction caused reductions of 90.9 and 84.7% in the increase in height and diameter of seedlings subjected to 25% water replacement when compared to seedlings with 100% water replacement, while biomass accumulation reduced by 96.9%. The kc values increased throughout the seedling production cycle, ranging from 0.59 to 2.86. Maximum water sensitivity occurred at 50% water replacement, with Ky = 1.62. Maximum carbon assimilation rates occurred in the morning, ranging from 6.11 to 12.50 µmol m-2 s-1. Ipê-rosa seedlings regulate the physiology of growth, gas exchange, and Chl a fluorescence depending on the amount of water available, and only 25% of the water re-placement in the substrate allows the seedlings to survive.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

Kinesiophobia (fear of movement) has been recognized as a significant barrier to recovery and rehabilitation in patients after total knee arthroplasty (TKA). Our goal was to identify predictors of kinesiophobia and examine its correlation with early functional outcomes in TKA recipients. On the first and fifth postoperative days (POD1 and POD5), we evaluated pain using the International Pain Outcomes Questionnaire (IPO-Q) and created multidimensional pain composite scores (PCS). Pain Composite Score-total (PCStotal) assesses the overall impact of pain, taking into account outcomes of pain intensity, pain-related interference with function, and emotions and side effects. Functional status on POD 5 was determined by the Barthel index, 6-minute walking test, and knee range of motion. Kinesiophobia was measured on POD5 using the Tampa Scale for Kinesiophobia (TSK) and multivariable logistic regression was used to assess factors associated with kinesiophobia. Among 75 TKA patients, 27% exhibited kinesiophobia. The final regression model highlighted PCStotal on POD5 (OR=6.2, CI=1.9-19.9), PCStotal (OR=2.1, CI=1.2-3.8) on POD1, and the intensity of chronic pain before surgery (OR=1.4, CI=1.1-2.1) as significant kinesiophobia predictors. On POD5, those with kinesiophobia showed increased dependency, slower gait, and poorer knee extension recovery. This study highlights the importance of identifying and addressing kinesiophobia in TKA patients to optimize functional outcomes and improve recovery. Also, it is important to assess not only pain intensity but also the physical and emotional interference caused by pain, which can contribute to the development of kinesiophobia.

Gait analysis has historically been implemented in laboratory settings with expensive instruments; however, recently, wearable sensors have allowed the integration into clinical applications and use in daily activities. Previous studies have shown poor validity of ankle joints using inertial measurement units (IMUs), especially for small movement ranges. The purpose of this study was to validate the ability of commercially available IMUs to accurately measure the ankle joint angles during running. Ten healthy subjects participated in the study. Validation was performed by comparing the ankle joint angles measured using the wearable device with those obtained using the gold standard motion capture system during running. Reliability was evaluated using the intraclass correlation coefficient and standard error of measurement, whereas validity was evaluated using Pearson coefficient correlation method. Day-to-day reliability was excellent in the two planes for ankle joints. Validity was good in both sagittal and frontal planes for ankle joints. The results suggested that the developed device might be used as an alternative tool to the 3D motion capture system.

Two isotropic pitches were prepared by air blowing and nitrogen distillation method using ethylene tar (ET) as a raw material. And correspondent carbon fibers were obtained through conventional melt spinning, stabilization and carbonization. The structures and properties of resultant pitches and fibers were characterized and their differences were discussed in this work. The results showed that introduction of the oxygen by air blowing method could quickly increase the yield and softening point of pitch. Moreover, the air blown pitch (ABP) composed of linear methylene chains of aromatic molecules while the nitrogen distilled pitch (NDP) mainly contained polycondensed aromatic rings, which was due to the oxygen containing functional groups existed in ABP could impede order stack of pitch molecules and form methylene bridge structure, instead of aromatic condensed structure like NDP. Meanwhile, the spinnability of ABP was not decreased even containing 2.31 wt% oxygen. In contrast, ABP had narrower molecular weight distribution, which contributed to better stabilization properties and higher tensile strength of carbon fiber. The tensile strength of carbon fibers from ABP was reached to 860 MPa with fiber diameter of about 10 μm, which was higher than that of NDP-derived carbon fibers of 640 MPa.

Ankle joint flexion and extension exercises play an important role in the rehabilitation training of patients who have been injured or bedridden for a long time before and after surgery. Accurately guiding patients to perform ankle flexion and extension exercises can significantly reduce deep vein thromboembolism. Currently, most ankle rehabilitation devices focus on assisting patients with ankle flexion and extension movements, and there is a lack of devices for effectively monitoring these movements. In this study, we designed an ankle joint flexion and extension movement monitoring device based on a pressure sensor. It is composed of an STM32 microcontroller, a pressure sensor, an HX711A/D conversion chip, and an ESP8266 WiFi communication module. The value of force and effective number of ankle joint flexion and extension movements were obtained. An experimental device was designed to verify the accuracy of the system. The results showed that the device can effectively monitor and control ankle flexion and extension movements remotely, ultimately ensuring that the patient can effectively monitor and grasp the active ankle pump movement.

A position sensing glove, called SmartScan, that creates a 3D virtual model of a real object is presented. The data from the glove is processed by a volume minimization algorithm to validate the position sensor data. This allows only data from the object’s surface to be retained. The data validation algorithm allows the user to progressively improve an image by repeatedly moving their hand over the object. In addition, the user can choose their own balance between feature resolution and invalid data rejection. The SmartScan glove is tested on a foot model and is shown to be robust against motion artifacts, and has a mean accuracy of 2.9 mm (compared to a 3D model generated from optical imaging) without calibration.

Chronic kidney disease (CKD) is actually considered a public health priority according to the increasing number of patients affected by this condition: this casuistry is not only related to specific glomerular, tubular or autoimmune diseases or a consequence of acute kidney injury (AKI) episodes leading to organ failure, but it is tied to the progression of life expectancy and the impact of comorbidities such as cardiovascular disease, diabetes and cancer. CKD and its comorbidities promote low grade inflammatory status with an impact on patients’ clinical conditions, reducing their possibility for kidney transplantation or graft survival and their survival when receiving renal replacement therapies such as hemodialysis (HD) or peritoneal dialysis (PD). CKD is often referred to as an ageing accelerator: innate immune system dysregulation, in the uraemic proinflammatory milieu, is involved in this accelerated senescence phenomena and pentraxins, particularly Pentraxin-3 (PTX-3), are of particular interest in the development of kidney disease. A complete understanding of the mechanism of CKD progression, innate immune system involvement and a proper definition of PTX-3 role in kidney disease, could redefine the approach for diagnosis and a more centered patients’ management to slow down CKD progression over time and reduce its clinical and social impact.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.

Background: Diagnostic accuracy of Parkinson’s disease (PD), a synucleinopathy, based on diagnostic criteria is suboptimal. A biomarker for synucleinopathies is pivotal both from a clinical and from a research aspect. CSF a-synuclein has been extensively studied over the past two decades as a candidate biomarker of synucleinopathies. Herein we present data on studies focusing on total, phosphorylated and oligomeric CSF a-synuclein in PD. Methods: Pubmed, Scopus and Web of Science were searched for studies with &gt;10 PD patients and control subjects, with data (mean, SD) on total, phosphorylated or oligomeric a-synuclein. Cohen’s d, as a measure of effect size, was calculated for all a-synuclein forms. Subgroup analysis and meta-regression were performed in an effort to explain between-study heterogeneity. Results: Thirty studies on total, six studies on oligomeric and one study on phosphorylated a-synuclein were included. Total a-synuclein was decreased and oligomeric a-synuclein increased in PD patients vs. controls. Effect size was medium for total and high for oligomeric a-synuclein. A-syn forms provided suboptimal combined sensitivity/specificity for the differentiation of PD from controls. There was significant between-study heterogeneity. PD cohort characteristics (sex, age, disease duration, UPDRS, H&amp;Y) and study characteristics (study design, healthy vs. neurological controls, control for CSF blood contamination, method of a-syn measurement) could not account for between-study heterogeneity. Publication bias was limited. Conclusions: CSF a-synuclein levels lack sufficient accuracy to be used as biomarkers for PD. Standardization of (pre)analytical variables may improve the discriminatory power of a-synuclein forms in the future.

This study aimed to evaluate the effect of three yeast strains, Pichia guilliermondii (Levica 27), Candida norvegensis (Levazoot 15), and a commercial product (Levucell® SC 10) containing Saccharomyces cerevisiae, on in vitro rumen fermentation of two substrates: corn stover and a total mixed ration (TMR). Samples were taken 24 hours post-fermentation to measure pH, ammonia nitrogen (NH3-N), gas production, and volatile fatty acid (VFA) concentrations. The addition of yeasts did not affect gas production at 24 hours for either diet. For pH, differences between yeast strains were noted when TMR was used. The lowest NH3-N concentration (6.1 mM) was recorded with corn stover, showing similar results across strains. Conversely, NH3-N levels with TMR ranged from 47 mM to 66 mM. The inclusion of all three yeast strains increased the molar concentrations of total VFA, as well as acetic (C2), propionic (C3), and butyric (C4) acids in the rumen fluid. The C2:C3 ratio remained unchanged with corn stover but decreased with the inclusion of Levica 27 and Levazoot 15 in the TMR. With the commercial product Levucell® SC 10, this ratio was comparable to the control treatment. In conclusion, Levica 27 and Levazoot 15 demonstrated a stimulatory effect on in vitro rumen fermentation for the evaluated diets, evidenced by increased VFA concentrations.

CO2 emission activity of xylotrophic fungi response to an increase in temperature in the range of 10-30 °C on the example of pure dikaryotic cultures of Fomes fomentarius s. str., F. inzengae, Fomitopsis betulina, F. pinicola, Phellinus igniarius was analyzed. Emission activity was assessed by the difference in CO2 concentration in 0.5-liter exposure chambers with Petri dishes with mycelium growing on agar at the beginning of exposure and an hour later using a Gasmet DX-4030 FTIR spectrometer (Gasmet Technologies Oy, Finland), error measurements ±50 ppm. Specific (μg CO2/cm2/h) and total (μg CO2/h) emission activity and its relationship with temperature and size (area) of the mycelium were assessed. It has been shown that in the range of 10-30 °C, the specific and total CO2 emission activity of the mycelium is closely and positively related to temperature. Specific emission, which is an indicator of the respiratory activity of the mycelium, does not depend on its size; its only driver is temperature, the relationship with which is linear: an increase in temperature by 10 °C causes an increase in the specific emission activity of the mycelium by 1.7 times. The total CO2 emission activity, which is an indicator of the total amount of CO2 emitted, is directly proportional to the specific emission activity and the size of the mycelium. In the range of 10-30 °C, an increase in temperature causes an almost equal increase in both the specific emission activity of the mycelium (Q10 1.7) and its growth (Q10 1.5) and causes an exponential increase in the total emission of CO2. This must be taken into account when predicting CO2 emissions from woody debris under climate change, as it could potentially contribute to accelerating climate change.

Osteomyelitis is a significant cause of total carcass condemnation in pigs at the slaughterhouse. The decision for total condemnation of a pig carcass for osteomyelitis is often based on traditional perceptions of the risk of pyemia, leading to controversy among Official Veterinarians (OV) in the industry. This review aims to provide a more comprehensive understanding of the etiopatho-genesis of osteomyelitis in pigs, the microorganisms involved, and the risk factors. It also high-lights the urgent need for a more uniform method to evaluate osteomyelitis cases, which could significantly reduce economic losses in the industry. Lesions originating from tail-biting, tail docking, castration, teeth resection, and raw management are described as risk factors for oste-omyelitis. Osteomyelitis is caused by the entry of pathogens into the bloodstream of the animal through an open wound. The most described pathogens are Trueperella monocytogenes, Staphylo-coccus aureus, and Streptococcus spp. At slaughter, OVs condemn carcasses with osteomyelitis due to pyemia. Signs of acute disease are essential to identify pyemia cases. In chronic cases, total carcass condemnation can be avoided depending on the number of lesions and number of vertebrae af-fected. A clear overall image of the problem would help authorities in various countries adopt a more homogenous approach.

Adeno-associated viral (AAV) vectors can be used for gene delivery. AAV.CAP-Mac was recently developed; it can cross the blood-brain barrier and transduce cells throughout the CNS. However, some brain regions were not transduced in adult rhesus monkeys. Additionally, AAV vectors can only package 5 kb of DNA. Also, AAV vectors may be genotoxic and cytotoxic, especially at high doses. Finally, AAV vectors are very expensive to produce at sufficiently high titers for treatment. Off-the-shelf cell-based delivery systems wherein the cells can infiltrate the target tissue and be hyper-motile would be ideal. Also, mRNA-based gene editing would be a transient treatment, and thus be much safer.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

In-depth research on the rehabilitation mechanism and motion characteristics of a rehabilitation training robot based on 4-UPUS parallel mechanism. The overall design and the working principle of each key component are explained, and the robot rehabilitation scheme is described. The static analysis and modal analysis of the robot bearing structure are carried out to verify whether the static mechanical characteristics of the mechanism meet the application requirements under working conditions.A simplified mathematical model of the six-bar linkage mechanism is established, and the kinematics of the mechanism is solved by the geometric analysis method. The motion characteristic diagram of each key point is obtained through simulation calculation. Establish the motion model of the parallel mechanism, and discuss the working space and motion performance analysis of the mechanism. The forward solution analysis of the mechanism position is carried out by using the numerical analysis method, and the three-dimensional graphics of the attitude angle and linear displacement of the reachable working space are obtained.Taking the UPUS single branch chain as the analysis object, the single open chain analysis method is used to solve the kinematics image of the corresponding surface in the working space of the mechanism, which verifies the correctness of the kinematics theoretical solution and the feasibility of simulation.The research results show that the 4-UPUS parallel mechanism rehabilitation training robot can cooperate with the ankle joint for rehabilitation training. It makes up for the single movement of the current lower limb rehabilitation robot and the unsatisfactory rehabilitation effect, and provides a reference for the practical application of the subsequent ankle joint rehabilitation robot system.

This study investigated the effect of partially replacing fish meal with krill and copepod meals in inert diets, co-fed with shrimp, on the growth and nutrient digestibility of long-snout seahorse (Hippocampus guttulatus). A control diet (Diet 1) using raw starch and four experimental diets with similar protein (≈44.8%) and energy (≈15.1 MJ/kg) levels were tested. Diet 2 used fish meal as the sole protein source, while in Diets 3-5, krill and copepod meals replaced 44% of the fish meal. Seahorses fed Shrimp + Diets 2-5 showed significantly higher growth rates (P &lt; 0.05) than those fed Shrimp + Diet 1, though there were no significant growth differences among Diets 2-5. Digestibility of dry matter (46.1% to 72.2%), lipids (73.3% to 85.5%), crude protein (89.8% to 95.8%), energy (82% to 92.2%), and phosphorus (28.7% to 64.4%) varied with diet, being consistently lower in seahorses fed Shrimp + Diet 1. As an agastric species, H. guttulatus did not exhibit impaired digestibility for any of the tested nutrients, minerals, or energy. This study suggests that crustacean meals can effectively substitute fish meal in inert diets for this species, contributing to the sustainability and optimization of captive seahorse husbandry practices.

Addressing non-unions involves stabilizing the affected area through osteosynthesis and improving bone biology using bone grafts. However, there is no consensus on the optimal treatment method. This study aims to compare outcomes of non-union revision using conventional treatment methods (metal hardware ± graft) versus osteosynthesis with the human, allogeneic cortical bone screw (Shark Screw®). Thirty-four patients underwent conventional treatment, while 28 cases received Shark Screws®. Patient demographics, bone healing, time to bone healing, and complications were assessed. Results revealed a healing rate of 96.4% for the Shark Screw® group, compared to 82.3% for the conventionally treated group. The Shark Screw® group exhibited a tendency for faster bone healing (9.4±3.2 vs. 12.9±8.5 weeks, p=0.05061). Hardware irritations led to six metal removals in the conventional group versus two in the Shark Screw® group. The Shark Screw® emerges as a promising option for personalized non-union treatment in the foot, ankle, and select lower leg cases, facilitating effective osteosynthesis and grafting within a single construct, promoting high union rates, low complications, and a rapid healing process.

The present study was conducted the status of sea bass from Kokko and Kyuntone of The Gulf of Motttama Wetland (GoMW) area in Thanatpin Township in Bago Region Myanmar from September 2019 to August 2020. Fifty specimens were monthly collected, measured and weighed. Invoices of sea bass were collected for the depot and fish sellers by monthly. In Kokko, mean value of standard length and body weight were highest in March (32.70±1.58, 660.7±112.23). The mean value of standard length was peak in January (31.39±7.16) but peak of body weight was in March (963.24±280.86) in Kyuntone villages. The lowest mean value of standard length and body weight were found in June at both study areas. According to the invoice data revealed that monthly catch weight of sea bass is most abundance in October (829.92) kg in Kokko, (339.12) kg in Kyuntone. Based on price of relations to size group, small size C &lt; 300g (41%) was mostly abundance in Kokko and in Kyuntone small size C &lt; 300g (35%) was second abundance. Specimens were not landed in April and May. In June, young specimens were very rarely seen in both study sites. The important roles of wetland fishes, the economic valuation of GOMW in Myanmar and samples of fishing gear and value chain of sea bass in Myanmar was expressed in this study.

There is limited data on pregnancy outcomes in Pompe Disease (PD) resulting from deficiency of the lysosomal enzyme acid alpha-glucosidase. Late-onset PD is characterized by progressive proximal muscle weakness and decline of respiratory function secondary to the involvement of the respiratory muscles. In a cohort of twenty-five females, the effects of both PD on the course of pregnancy and the effects of pregnancy on PD were investigated. Reproductive history, course of pregnancy, use of Enzyme replacement therapy (ERT), PD symptoms, and outcomes of each pregnancy were obtained through a questionnaire. Among 20 subjects that reported one or more pregnancies, one subject conceived while on ERT and continued therapy through two normal pregnancies with worsening of weakness during pregnancy and improvement postpartum. While fertility was not affected, pregnancy may worsen symptoms, or cause initial symptoms to arise. Complications with pregnancy or birth were not higher, except for an increase in the rate of stillbirths (3.8% compared to the national average of 0.2-0.7%). Given small sample size and possible bias of respondents being only women who have been pregnant, further data may be needed to better analyze the effects of pregnancy on PD, and the effects of ERT on pregnancy outcomes.

The main goal of this study was to evaluate sugarcane bagasse ash as a partial cement replacement material. Sugarcane bagasse ash is a by-product of fuel blending in the sugar industry. Yet all economic sugar is obtained after extraction from the cane. The disposal of the discharged waste in agriculture causes environmental problems in the sugar industry. The cement industry also creates environmental problems due to carbon dioxide emissions during cement manufacturing. Initially, bagasse ash samples were collected from the rubble of the Arjo Didessa sugar factory. The crude bagasse ash was sieved with a sieve size of 250µm. The strength of grade C-25 concrete was designed using five different concrete mixture proportions ranging from 5 to 20% cement by weight, including a water-cement ratio of 0.45. Impact strength tests were conducted at 7, 14, 21, and 28 days of age for each replacement ratio. For the experimental work, a total of 60 cubic concrete specimens were cast for compressive strength tests, and 15 cylindrical concrete specimens were cast for water absorption tests. Working compressive strength results indicated that bagasse ash could replace up to 5% of ordinary Portland cement concrete.

Testing in animals is mandatory in drug testing and the gold standard for evaluation of toxicity. This situation is expected to change in the future because the 3Rs principle, which stands for replacement, reduction and refinement of the use of animals in science, is reinforced by many countries. On the other hand, technologies for alternatives to animals experiments have increased. The necessity to develop and use of alternatives is influenced by the complexity of the research topic and also by the fact, to which extent the currently used animal models can mimic human physiology and/or exposure. Rodent lung morphology and physiology differs markedly for that of humans and inhalation exposure of the animals are challenging. In vitro and in silico methods can assess important aspects of the in vivo action, namely particle deposition, dissolution, action at and permeation across the respiratory barrier and pharmacokinetics. Out of the numerous homemade in vitro and in silico models some are available commercially or open access. This review discusses limitations of animal models and exposure systems and proposes a panel of in vitro and in silico techniques that, in the future, may replace animal experimentation in inhalation testing.

A novel domination invariant defined by Boutrig and Chellali in the recent: total vertex-edge domination. In this paper we obtain an improved upper bound of total vertex edge-domination number of a tree. If is a connected tree with order , then with and we characterize the trees attaining this upper bound. Furthermore we provide a characterization of trees with

The Loess Plateau is an important region for vegetation restoration in China, however, changes in soil organic carbon (SOC), soil nutrients, and stoichiometry after restoration in this vulnerable ecoregion are not well understood. Typical restoration types, including orchardland (OL), grassland (GL), shrubland (SL), and forestland (FL) were chosen to examine changes in the stocks and stoichiometry of SOC, soil total nitrogen (TN), and soil total phosphorus (TP) at different soil depths and recovery times. Results showed that SOC stocks first increased and then stabilized in OL, GL, and SL at 0–30 cm depth, while in FL, stocks gradually increased. Soil TN stocks first increased and then decreased in OL, SL, and FL with vegetation age at 0–30 cm depth, while soil TP stocks showed little variation between restoration types. In the later stages of restoration, the stocks of SOC and soil TN at 0–30 cm soil depth were still lower than those in natural grassland (NG) and natural forest (NF). The overall C:N, C:P, and N:P ratios increased with vegetation age. Additionally, the SOC, soil TN and soil TP stocks, and C:N, C:P, and N:P ratios decreased with soil depth. The FL had the highest rate of change in SOC and soil TN stocks, at 0-10 cm soil depth. These results indicate a complex response of SOC, soil TN, and soil TP stocks and stoichiometry to vegetation restoration, which could have important implications for understanding C, N, and P changes and nutrient limitations after vegetation restoration.

Powered ankle prostheses have been proven to improve the walking economy of people with transtibial amputation. All commercial powered ankle prostheses that are currently available can only perform one-degree-of-freedom motion in a limited range. However, studies have shown that the frontal plane motion during ambulation is associated with balancing. In addition, as more advanced neural interfaces have become available for people with amputation, it is possible to fully recover ankle function by combining neural signals and a robotic ankle. Accordingly, there is a need for a powered ankle prosthesis that can have active control on not only plantarflexion and dorsiflexion but also eversion and inversion. We designed, built, and evaluated a two-degree-of-freedom (2-DoF) powered ankle-foot prosthesis that is untethered and can support level-ground walking. Benchtop tests were conducted to characterize the dynamics of the system. Walking trials were performed with a 77 kg subject that has unilateral transtibial amputation to evaluate system performance under realistic conditions. Benchtop tests demonstrated a step response rise time of less than 50 milliseconds for a torque of 40 N·m on each actuator. The closed-loop torque bandwidth of the actuator is 9.74 Hz. Walking trials demonstrated torque tracking errors (root mean square) of less than 7 N·m. These results suggested that the device can perform adequate torque control and support level-ground walking. This prosthesis can serve as a platform for studying biomechanics related to balance and has the possibility of further recovering the biological function of the ankle-subtalar-foot complex beyond the existing powered ankles.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

Osteoarthritis (OA) poses a growing challenge for the aging population, especially in hip and knee joints, contributing significantly to disability and societal costs. Conventional clinical evaluations, typically performed in controlled settings, face difficulties in capturing the dynamic characteristics of rehabilitation and functioning in real-life scenarios. The study assessed the use of automated unsupervised evaluations in the rehabilitation process for patients after hip and knee replacements. We analyzed data from 1144 individuals who used a digital application after surgery, activity data were collected using the Garmin Vivofit 4. Several parameters such as the Peak 6-Minute Consecutive Cadence (P6MC) and Peak 1-Minute Cadence (P1M) were computed and analyzed on a daily basis. The results indicated that cadence measurements, specifically, can effectively differ among individuals with hip and knee conditions as well as the recovery process. Moreover, these metrics demonstrated a high level of responsiveness in monitoring the progress of recovery, surpassing the effectiveness of simply measuring the total number of steps taken. The study highlighted the capacity of technology-driven, patient-centered rehabilitation to improve accuracy, tailor therapy to individual patients, and increased patient involvement. This research also highlighted the significance of automated, unsupervised assessments in enhancing rehabilitation results for OA patients following hip and knee replacement, as tele-rehabilitation becomes increasingly important.

Background: Our objective was to conduct a comprehensive analysis of the reproducibility of foot and ankle anthropometric measurements with a three-dimensional (3D) optical scanner. Methods: We evaluated thirty-nine different anthropometric parameters obtained with 3D Laser UPOD-S Full-Foot Scanner in a healthy population of twenty subjects. We determined the variance of the measurements for each foot/ankle, and the average variance among different subjects. Results: For 40 feet and ankles (15 women and 5 men; mean age 35.62 +/- 9.54 years, range 9-75 years), the average variance was 1.4 ± 2 (range 0,1 to 8). Overall, the mean absolute measurement error was < 1 mm, with a maximum variance percentage of 8.3%. Forefoot and midfoot circumferences had a low variance < 2.5, with variance percentages < 1%. Hindfoot circumferences, malleolar heights, and the length of the first and fifth metatarsal to the ground contact points showed the highest variance (range 1 to 7). Conclusion: This optical scanner achieved a good reproducibility of a large set of foot and ankle anthropometric measurements. It is a valuable tool for clinical and research purposes.

Purpose: While resultant maximal voluntary contraction (MVC) is commonly used to assess muscular performance, the simultaneous activation of antagonist muscles could dramatically underestimate the strength of the agonist muscles. While quantification of antagonist torque has been performed in plantar- (PF) and dorsi-flexion (DF) joint in isometric conditions, it has yet to be determined in anisometric (concentric and eccentric) conditions. Methods: The experiment was performed in 9 participants through 2 sessions (reliability). The MVCs in DF and PF were measured in isometric, concentric and eccentric conditions (10°.s^-1). Electromyographic (EMG) activities from the soleus, gastrocnemius medialis and lateralis, and tibialis anterior muscles were simultaneously recorded. The EMG biofeedback method was used to quantify antagonist torque, where participants were asked to maintain a level of EMG activity, corresponding to antagonist EMG activity and related to the muscle contraction type, according to a visual EMG bio-feedback displayed on a screen. Results: Resultant torque significantly underestimated agonist torque in DF MVC (30-65%) and to a lesser extent in PF MVC (3%). Triceps surae antagonist torque was significantly modified with muscle contraction type, showing higher antagonist torque in isometric (29 Nm) than eccentric (23 Nm, p < 0.001) and concentric (14 Nm, p < 0.001) conditions and resulting in modification of the DF MVC torque-velocity shape. The difference between DF eccentric and concentric MVC was attenuated when considered agonist torque (12%) rather than resultant torque (45%). Conclusion: Estimation of the antagonist torque in isometric or anisometric condition brings new insights to assessment of muscular performance and could result in costly misinterpretation in strength training and/or rehabilitation programs.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

Nowadays, the high demand for healthy foods and sustainable products, has led the food industry to explore innovative food technologies, such as fortification with bioactive compounds like antioxidants and polyphenols, that may be sourced from herbs or by-products. The aim of the present study was to explore the enrichment of refined olive oils with natural bioactive compounds such as the herbs rosemary (salvia rosmarinus), basil (ocimum basil), sage (salvia officinalis), lemon balm (melissa oficinallis), st. john’s wort (hypericum perforatum), pink savory (Thymbra satureja), dittany (origanum dictamnus), and by-products such as pomace from olives, olive leaves (olea europaea tree), orange peel (citrus sinensis), lemon peel (citrus limon), pomegranate peel (punica granatum) and mandarin peel (citrus reticulate). The fortification of the refined olive oils was performed with the use of different methodologies such as Conventional maceration (CM), Incubation shaking maceration (ISM), and Ultrasound assisted maceration (UAM). Their phenolic content and antioxidant capacity were measured with Folin–Ciocalteu assay and Ferric Reducing Antioxidant Power (FRAP) assay respectively. All methods demonstrated that different parameters such as time of maceration, temperature and sample concentration, play an important role in the fortification process of the refined olive oils. The predicyed bioavailability of the antioxidant and phenolic compounds in the fortified oils was determined with in vitro digestion and ranged from 4.84% to 53.11%. Furthermore, the refined olive oils fortified with pomace, basil, st. john's wort, and pomegranate peel presented the highest antioxidant and phenolic predicted bioavailability indices during the in vitro process compared to the control refined olive oil. Finally, fortification with natural herbs or by-products can be considered an innovative method for the improvement of the nutritional value of refined olive oils.

This study addresses the urgent need for sustainable protein sources in aquaculture due to the depletion of marine resources and rising costs. Animal protein sources, particularly poultry by-product meal (PBM) and insect exuviae meal, are investigated as viable alternatives to fishmeal (FM). Research confirms the successful replacement of FM with a combination of PBM and insect exuviae meal (up to 50%) in the diet of European seabass without compromising growth, feed conversion, gut health and liver fat content. In particular, growth performance was robust with both PBM formulations, with the 25% PBM diet showing better results. Histological examinations showed good gut and liver health, contradicting the concerns of previous studies. The study emphasizes the importance of holistic analyzes that go beyond growth parameters and include histomorphological investigations. The results show that PBM in combination with insect/exuviae meal is well tolerated by seabass, which is consistent with literature reports of mitigating negative effects on gut health. A detailed analysis of the microbiota revealed a decrease in the Firmicutes/Proteobacteria ratio due to an increase in potentially pathogenic bacteria. However, the formulation containing insect exuviae partially counteracted this effect by preserving the beneficial Lactobacillus and promoting the synthesis of short-chain fatty acids (SCFA), particularly butyrate. Chitin-rich components from insect exuviae were associated with improved gut health, which was supported by increased production of SCFA, which are known for their anti-inflammatory properties. The study concludes that a combination of PBM and insect/exuviae meal can replace up to 50% of FM in the diet of seabass, supporting sustainable aquaculture practices. Despite some changes in the microbiota, the negative effects are mitigated by the addition of insect exuviae, highlighting their potential as a prebiotic to increase fish productivity and contribute to a circular economy in aquaculture.

Immortal-time bias (ITB) is known to be common in cohort studies and distorts the association estimates between treated and untreated groups. We used data from the last of two large studies in an Italian province on COVID-19 vaccines safety and effectiveness incurred this bias, and aligned the entire population on a single index date, to correct the ITB. We considered the "all-cause deaths" outcome to compare the survival curves between the unvaccinated group and the various vaccination statuses. The all-cause deaths Hazard Ratios in univariate analysis for unvaccinated (reference) versus vaccinated with 1, 2, 3/4 doses were 0.88 (CI95: 0.78 –1.00; p-value 0.044), 1.23 (1.16–1.32; p-value ≤0.001) and 1.21 (1.14–1.29; p-value ≤0.001), respectively. The multivariate values were 2.40 (2.00–2.88; p-value <0.0001), 1.98 (1.75–2.24; p-value <0.0001), 0.99 (0.90–1.09; ns). The possible explanations of the trend of the Hazard Ratios as vaccinations increase could be a harvesting effect; a calendar-time bias, accounting for seasonality and pandemic waves; a case-counting windows bias; a healthy-vaccinee bias; or some their combination. With two and even with 3/4 doses the calculated Restricted Mean Survival Time and Restricted Mean Time Lost have shown a small but significant downside for the vaccinated populations.

3.9 million individuals rely on kidney replacement therapy worldwide. They experience height-ened susceptibility to cardiovascular diseases and mortality, alongside an increased risk of in-fections and malignancies, with inflammation being key to explaining this intensified risk. This study utilized semi-targeted metabolomics to explore novel metabolic pathways related to in-flammation in this populations. We collected pre and post-session blood samples of patients who had already undergone one year of chronic hemodialysis. And used liquid chromatography and high resolution mass spectrometry to perform a metabolomic analysis. Afterwards, we employed both univariate (Mann-Whitney test) and multivariate (logistic regression with LASSO regulari-zation) to identify metabolites associated with inflammation. In the univariate analysis, in-dole-3-acetaldehyde, 2-ketobutyric acid, and urocanic acid showed statistically significant de-creases in median concentrations in the presence of inflammation. In the multivariate analysis, metabolites positively associated with inflammation include allantoin, taurodeoxycholic acid, norepinephrine, pyroglutamic acid, and L-hydroorotic acid. Conversely, metabolites showing negative associations with inflammation include benzoic acid, indole-3-acetaldehyde, methio-nine, citrulline, alphaketoglutarate, n-acetyl-ornithine and 3-4-dihydroxibenzeneacetic acid. Non inflamed patients exhibit preserved autophagy and reduced mitochondrial dysfunction. Under-standing inflammation in this group hinges on the metabolism of arginine and the urea cycle. Additionally, the microbiota, particularly uricase-producing bacteria and those metabolizing tryptophan, play critical roles.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

Although initially conceived for high-risk patients who are ineligible for surgical aortic valve replacement (SAVR), transcatheter aortic valve replacement (TAVR) is now recommended in a wider spectrum of indications including young patients. However, as for SAVR, TAVR is also associated with a risk of infectious complications, namely prosthetic valve endocarditis (PVE). As the number of performed TAVR procedure increases, and despite the low incidence of PVE post TAVR, clinicians should be familiar with the associated risk factors and the clinical presentation. Whereas the diagnosis of native valve endocarditis can be straightforward applying the modified Duke criteria, the diagnosis of PVE is more challenging given its atypical symptoms, lower sensitivity of the criteria, and low diagnostic yield of conventional echocardiography. Delay in proper management can be associated with increased morbidity and mortality. Therefore, clinicians should have a high index of suspicion and initiate proper work-up according to the severity of illness, the underlying host, and the local epidemiology of the causative organisms. The most common causative pathogens are Gram-positive bacteria such as S. aureus, coagulase negative staphylococci, Enterococcus spp. and Streptococcus spp. (particularly the viridans group) and, less likely Gram-negative and fungal pathogens. The high prevalence of antimicrobial resistance complicates the choice of therapy. There remain controversies regarding the optimal management strategies including indications for surgical interventions. Surgical assessment is recommended early in the course of illness and surgical intervention should be considered in selected patients. As in other PVE, duration of therapy depends on the isolated pathogen, the host, and the clinical response. Since TAVR is a relatively new procedure, the outcome of TAVR-PVE is yet to be fully understood.

Accordingly, a lot of dry direct seeding rice would be dense planted, that the initial seedling quantity could approach or even exceed the targeted effective panicle number. While limit information is available to evaluate the effects of involved novel nitrogen application methods, that total nitrogen once applied at a determined leaf age stage, on the yield formation traits of such dense planted dry direct seeding rice. The two-year experiments with total 180 kg ha-1 nitrogen once applied time treatments at sixth (L6), seventh (L7), eighth (L8), ninth (L9) and tenth (L10) leaf age stages were carried out. Results showed that the above-ground dry matter weight at maturity and grain yield of L8 was 2.1% ~ 11.8% and 4.0% ~ 9.9% higher than those of other treatments. Compared to other treatments, the higher above-ground dry matter weight after heading stage, bigger mean leaf area index with higher leaf area index at heading stage, increased leaf area duration, crop growth rate and net assimilation rate from jointing to heading period were important traits of higher grain yield formation of L8. In addition, the L8 had relative higher grain-leaf ratio traits than other treatments. Overall, a total 180 kg ha-1 nitrogen with mixed urea and compound fertilizer once applied at eighth leaf age stage would be suggest a useful high yield cultivation method for dense planted dry direct seeding rice in rice-wheat rotation system.

This study investigates the trends and patterns of robotic-assisted total knee arthroplasty (RA-TKA) from 2016 to 2019. Using data from the Nationwide Inpatient Sample (NIS), we analyzed demographics, prevalence of comorbidities, total cost, and length of stay (LOS) for 88,415 RA-TKA cases identified during this period. Our analysis revealed a significant increase in RA-TKA procedures, from 5,330 in 2016 to 39,495 in 2019. Patients undergoing RA-TKA were slightly younger, with an average age of 66.2 years. The average hospital stay was 1.89 days, and total charges averaged $65,891. We also examined various comorbidities and demographic factors, including race, median household income, and hospital teaching status. The results show that RA-TKA usage in the US has grown substantially, with specific demographic and clinical patterns. Further studies on the long-term outcomes of RA-TKA are needed to fully understand the benefits of this technology.

Background: Recent disasters have demonstrated gaps in employers’ preparedness to protect employees and promote their well-being in the face of emergencies and disasters affecting the workplace and their communities. Total Worker Health (TWH), a comprehensive perspective developed by the National Institute for Occupational Safety and Health, is a helpful framework for addressing employer preparedness. It includes attention to health and safety at work, and the promotion of the health and well-being of the employee in the context of social determinants of health, such as work-life balance. Methods: TWH concepts, including the domains of TWH and the TWH Hierarchy of Controls, were investigated for their relevance to protecting employees and promoting their well-being during and after crises such as weather disasters, pandemics, and acts of terrorism. Building upon TWH concepts, an employer preparedness framework and model is proposed. Findings: The Model emphasizes upstream prevention, workplace-community linkages, social and economic impacts, and employer leadership through a cyclical planning process. Conclusions/Application to Practice: The Model can assist employers in advancing their preparedness for all hazards through self-assessment and planning agendas based upon the proposed domains.

Organ shortage is one of the most pressing issues with regard to human mortality. This issue is further complicated by the fact that HLA matching is required for patients, leading to restricted choices for transplant. If organs or tissues from non- or partially-HLA–matched donors could be edited such they evade cytotoxic T cells as well as natural killer cells, it would ameliorate the organ shortage problem.

The human ankle is a complex joint, most commonly represented as talocrural and subtalar axes. It is difficult to locate and take in vivo measurements of the ankle joint. There are no instruments for patients lying on a bed or the floor; that can be used in outdoor or remote sites. We have developed a "Turmell-meter" to address these issues. We started with the study of ankle anatomy and anthropometry, then we used the product of exponentials’ formula to visualize the movements. Furthermore, we built a prototype using human proportions and statistics. For pose estimation, we used a trilateration method by applying tetrahedral geometry. Additionally, we computed the axis direction by fitting 3D circles, plotting the manifold and chart as an ankle joint model. We presented the results of simulations, a prototype comprising 45 parts, specifically designed draw-wire sensors, and electronics. Finally, we tested the device by capturing positions and fitting them into the bi-axial ankle model as a Riemannian manifold. The Turmell-meter is intended to be a hardware platform for human ankle joint axis estimation, it is adjustable and has an easy setup. The proposed model has the properties of a chart in a geometric manifold, we provided the details

The ability to monitor Sprained Ankle Rehabilitation Exercises (SPAREs) in home environments can help therapists to ascertain if exercises have been performed as prescribed. Whilst wearable devices have been shown to provide advantages such as high accuracy and precision during monitoring activities, disadvantages such as limited battery life, users' inability to remember to charge and wear the devices are often the challenges for their usage. Also, video cameras, which are notable for high frame rates and granularity, are not privacy-friendly. This paper, therefore, proposes the use and fusion of unobtrusive and privacy-friendly sensing solutions for data collection and processing during SPAREs in home environments. Two Infrared Thermopile Array (ITA-32) thermal sensors and two Frequency Modulated Continuous Wave (FMCW) Radar sensors were used to simultaneously monitor 15 healthy participants during SPAREs which involved twisting their ankle in 4-fundamental movement patterns namely (i) extension, (ii) flexion, (iii) eversion and (iv) inversion. Experimental results indicated the ability to identify thermal blobs of participants performing the 4 fundamental movement patterns of the human ankle. Cluster-based analysis of data gleaned from the ITA-32 sensors and the FMCW Radar sensors indicated average classification accuracy of 96.9% with K-Nearest Neighbours, Neural Network, AdaBoost, Decision Tree, Stochastic Gradient Descent and Support Vector Machine, amongst others.

Objective: To examine the effect of bilateral total lobectomy and unilateral total lobectomy on improving thyroid function in patients with thyroid micropapillary carcinoma treated with euthyrox. Methods: The study was conducted on 68 patients with thyroid micro papillary carcinoma treated with euthyroxwho had been surgically treated with euthyrox in our hospital between January 2018 and December 2019. On the basis of random number grouping, they were divided into control groups (n = 34, bilateral total lobectomy) and observation groups (n = 34, unilateral total lobectomy plus isthmectomy). Thyroid function, free triiodothyronine (FT3), thyroid hormone (TSH), and voice function (VHI score) of the two groups were compared.Results: In comparison to the control group, the observation group had shorter incision lengths, shorter operation times, and shorter hospital stays, as well as less intraoperative bleeding and drainage volume, and the difference was statistically significant (P < 0.05); As compared with the control group, the observation group had higher FT4 and FT3 levels as well as lower TSH levels, a statistically significant difference (P < 0.05).VHI scores of emotions, function, physiology, and other voice functions were significantly lower among the observation group than those of the control group (P < 0.05).Conclusion: A unilateral total lobectomy with adjacent isthmus resection in patients with thyroid micro papillary carcinoma can yield ideal results, accelerate the time taken for surgical rehabilitation, improve thyroid function, thereby improving voice quality, as well as improve the overall prognosis of the patient.

In the context of autosomal dominant polycystic kidney disease (ADPKD), total kidney volume (TKV) plays a key role as biomarker of disease progression and response to therapy and has been recently recognized as enrichment biomarker and possible surrogate endpoint. Several imaging modalities and methods are available to calculate TKV, and the choice depends on the purpose of use. Technological advancements have made it possible to accurately assess cyst burden, that can be crucial to assess the disease state and help identifying rapid progressors. Moreover, the development of automated algorithms has increased the efficiency of total kidney and cyst volume measurements. Beyond total kidney and cyst volume, the quantification and characterization of non-cystic kidney tissue show potential to early stratify ADPKD patients, monitor disease progression, and possibly predict renal function loss. A broad spectrum of kid-ney MRI techniques are available to characterize kidney tissue, showing promise to non-invasively pick up early signs of ADPKD progression. Radiomics has been used to extract tex-tural features from ADPKD images, providing valuable information about the heterogeneity of the cystic and non-cystic components. This review provides an overview of ADPKD imaging bi-omarkers, focusing on quantification methods, potential, and necessary steps towards successful translation to clinical practice.

Breast Cancer Associated Susceptibility Proteins Type 1/2 (BRCA1/2) promote cellular functioning by modulating NRF2-mediated antioxidant signaling. Redox failure in women with BRCA1/2 insufficiency increases the risk for breast/ovarian/uterine cancers. Risk‐reducing salpingo‐oophorectomy (RRSO) is a prophylactic surgery of the reproductive organs, which is frequently conducted by the age of 40 to lower the occurrence of cancer in women with BRCA1/2 mutations. However, abrupt estrogen decline following RRSO causes ovarian failure, which implicates various cellular physiological processes, resulting in increased release of free radicals and subsequent severe onset of menopausal symptoms. Comfort measures (e.g., hormonal replacement therapy (HRT) and mindfulness-based stress reduction (MBSR)) may improve chronological menopause-related quality of life, but their specific effects are not clear in women with gene mutations. Aiming to fill the gap, this study used path analysis to examine the effects of HRT and MBSR on menopausal symptoms among RRSO patients (N = 199, mean age = 50.5 ± 6.7 years). HRT alleviated menopausal symptoms in BRCA2 carriers and women who were physically active, premenopausal at the time of RRSO, had a high BMI, and had no history of breast cancer. It increased the severity of urogenital symptoms in those with a history of cancer. MBSR, on the other hand, was associated with increased intensity of most menopausal symptoms. The results suggest that young women undergoing recent RRSO may benefit from HRT at an individual level while their need for extensive measures to optimize their psychological wellbeing is ongoing. Adverse effects of MBSR, which are captured in the present study imply that MBSR may interfere with redox sensitivity associated with estradiol fluctuations in BRCA1/2 carriers. Investigations are needed to test this hypothesis and elaborate on the underlying mechanisms in those women.

The aim of this review was to provide an update on the potential of cell therapies to restore or replace damaged and/or lost cells in retinal degenerative and optic nerve diseases, describing the available cell sources and the challenges involved in such treatments when these techniques are applied in real clinical practice. Sources include human fetal retinal stem cells, allogenic cadaveric human cells, adult hippocampal neural stem cells, human CNS stem cells, ciliary pigmented epithelial cells, limbal stem cells, retinal progenitor cells (RPCs), human pluripotent stem cells (PSCs) (including both human embryonic stem cells (ESCs) and human induced pluripotent stem cells (iPSCs)) and mesenchymal stem cells (MSCs). Of these, RPCs, PSCs and MSCs have already entered early-stage clinical trials since they can all differentiate into RPE, photoreceptors or ganglion cells, and have demonstrated safety, while showing some indicators of efficacy. Stem/progenitor cell therapies for retinal diseases still have some drawbacks, such as the inhibition of proliferation and/or differentiation in vitro (with the exception of RPE) and the limited long-term survival and functioning of grafts in vivo. Some other issues remain to be solved concerning the clinical translation of cell-based therapy, including (1) the ability to enrich for specific retinal subtypes; (2) cell survival; (3) cell delivery, which may need to incorporate a scaffold to induce correct cell polarization, which increases the size of the retinotomy in surgery and, therefore, the chance of severe complications; (4) the need to induce retinal detachment to perform the subretinal placement of the transplanted cell; and (5) the evaluation of the risk of tumor formation caused by the undifferentiated stem cells and prolific progenitor cells. Despite these challenges, stem/progenitor cells represent the most promising strategy for retinal and optic nerve disease treatment in the near future, and therapeutics assisted by gene techniques, neuroprotective compounds and artificial devices can be applied to fulfil clinical needs.

A recently published article posited the use of polymer matrix composites (PMCs) as a replacement material for low-carbon steel (LCS) in large power transformer (LPT) tanks [1]. PMCs offer potential advantages such as weight reduction, corrosion prevention, and self-healing of the tank material which may not be achievable with traditional LCS. LCS can arrest ballistic projectiles at relatively low velocities, but at higher velocities, penetration can occur leading to a potential major transformer failure. Numerical simulations of steel projectile impacts upon LCS plates and glass and/or carbon fiber polymer composite laminates showed that with sufficient thickness both could prevent projectile penetration. This prevention was especially efficient when the plates were coated with a high strain rate sensitive material such as polyurea (PU). Our simulations show that the addition of a 3 mm coating of PU to a standard 10 mm thick LCS plate used in LPT tanks could prevent penetration of a 400 m/s steel projectile. For PMC plates, the simulations with the same projectile velocity showed three times faster deceleration with a 3 mm PU coating than without the coating. Thus, two realistic approaches to improving the ballistic protection of LPTs are presented. In addition to their other advantages, this research clearly shows that PMCs with the coating could provide significant ballistic protection for the next generation of LPT tanks.

Purpose: Hormone Replacement Therapy (HRT), an FDA-approved treatment for menopausal conditions was found to be associated with increased risk of endometrial cancer and reduced oestrogen. Studies showing benefits of HRT in preventing chronic diseases lead to development of clinical guidelines by American College of Physicians. This study aims to assess effectiveness of HRT treatments across cardiometabolic measures including Triglycerides (TG), Follicle-Stimulating Hormone, LDL cholesterol, HDL cholesterol, and Estradiol in menopausal women. It reports gaps in scientific knowledge and clinical practice to enhance current guidelines and policies.Methods: A systematic methodology designed and published in PROSPERO (CRD42022346057) to report network meta-epidemiology analysis was utilised. We used databases by PubMed, Web of Science, ScienceDirect, EMBASE and MEDLINE for studies published between 30th of April 1980-2022. Effects of HRT treatments were explored using a mixed treatment comparison (MTC) model. Fixed and random-effects models were used to address heterogeneity in published studies. Publication bias was assessed and corrected using funnel plots and Egger’s test.Results: Of 45 eligible studies, our findings indicate a significant statistical heterogeneity between HRTs and reduction of TG, SFH, LDL-C alongside increase of HDL-C and Estradiol among menopausal women. The analysis suggests a lack of direct evidence to support their efficacy in reducing TG, SFH and LDL-C levels or to substantiate HRT’s effectiveness in increasing HDL-C and Estradiol. The results showed no significant publication bias in the meta-analysis of included studies.Conclusion: Our findings demonstrate that use of HRT interventions among menopausal women may reduce TG, FSH and LDL-C levels and increase levels of HDL-C and estradiol via oral and oral + transdermal administration. Our study reaffirms efficacy of HRT in supporting favourable lipid profile in menopausal women whilst highlighting the need for robust and inclusive epidemiology studies and clinical trials to further develop clinical guidelines and policies.

Considerable amounts of agro-industrial by-products are discarded or burnt as fuel every year. However, they can be utilized as a valuable source of fiber, phenolics and other useful compounds such as antioxidants. The profile of beneficial compounds can be affected by genotype, locality, orchard management and productive season, adding or decreasing the bioactive potential of by-products. In this study, hazelnut (Corylus avellana L.) and walnut (Juglans regia L.) nutshells were investigated for their fiber content and antioxidant capacity as valorized by-products for the industry. Determinations (ORAC, TPC and color asses) were performed in hazelnut and walnut orchards located in Southern Chile during three consecutive seasons (2020/21; 2021/22 and 2022/23). Analyses of oxygen radical absorbance capacity (ORAC) in nutshells showed the highest ORAC from both species in the season 2020/21 (3217 µmol TE g1DW for hazelnut shells and 4663 µmol TE g DW1 for walnut shells), while variability in the consecutive seasons was lower for hazelnut than in walnut. Total phenolic content in hazelnut shells was positively correlated with L* (R: 0.883) and E (R: 0.924) during 2020/21 season, also with L* for 2022/23 (R: 0.907). While ORAC was negatively correlated with L* (R: 0.922) in 2021/22. In addition, morphological and structural features of both nutshells examined by Scavenging Electron Microscopy (VP-SEM) and Confocal Scavenging Laser Microscopy (CSLM) revealed differential tissue distribution and accumulation patterns of both cellulose and lignin. On the other hand, photo-colorimetric values were determined for both shells and corresponding seasons, and non-significative differences were found both shells and among seasons Finally, these results provide insight into the physicochemical characteristics of two shell types which should be considered together with antioxidant capacity in their valorization as a residual material.

In different fields in our life, like physics, coding theory and computer science, graph labeling dramas an vital role and appears in many applications. A labeling of a graph is a map which assign each element in with a positive integer number. An edge irregular total -labeling is a function such that where and are weights for any two distinct edges. In this case, has total edge irregularity strength (TEIS) if is minimum. In our paper, we defined a new type of graphs called a triple star snake graph and star snake graph . Also, we investigated TEIS for a triple star snake graph . After that, we generalized the results for star snake graph .

Owing to their unique physicochemical properties, nanoparticles are used in a variety of ways in the field of cancer treatment, including imaging, drug delivery, and photothermal and photodynamic therapies. The fascinating properties of nanoparticles are determined by their size, morphology, and constituent elements, and various synthetic methods and post-synthetic techniques have been applied to control these factors. Herein, we present examples of shape and composition control through galvanic replacement, a technique that exploits redox potential differences between elements to induce spontaneous ion-exchange and highlight its specific contributions to cancer treatment applications. The present article identifies the recent advances in nanoparticle formation techniques and discusses the future outlook of the field.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

Wetlands are carriers of metals and organic pollutants from natural and anthropogenic sources. Studies have shown that sediments are sinks for these pollutants as they carry more than 99% of the total amount of metals which are released as soluble metals into the Lagoon. The University of Lagos, located at Akoka North eastern part of Yaba in Lagos Mainland runs along a highly industrialized and residential area. This paper reports the total metal concentrations in wetland and sediment and their seasonal variations. Wetland and sediment samples were collected for two seasons in 8 sampling sites. Results showed wetland data having lower concentrations of metals as compared to sediments. Wet season had higher concentrations of metals as compared to other season. Total concentrations in wetlands were Cd (1.0-6.0), Cu (1.0-11.0), Cr (0.3-82.7), Zn (2.7-65.0) and Pb (0.3-16.0) all in μg L-1 respectively. Statistical analysis showed that there was a significant difference between the wet and dry seasons for sediments. Cd was the only metal at acceptable levels while Cr, Cu, Pb and Zn concentrations all exceeded levels deemed acceptable by the SABS and the EPA. Therefore, the wetland is in poor health.

This study investigates how traumatic injuries alter joint movements in the ankle and foot. We used a brain injury model in rats, focusing on the hippocampus between the CA1 and dentate gyrus. We assessed the dissimilarity factor (DF) and vertical displacement (VD) of the ankle and metatarsus joints before and after the hippocampal lesion. We analyzed joint movements in rats after the injury or in rats treated with resveratrol, exercise, or a combination of both. Resveratrol facilitated the recovery of DF in both legs, showing improvements in the ankle and metatarsus joints on the third- and seventh days post-injury. The hippocampal lesion affected VD in both legs, observed on the third or seventh day after the injury. Both exercise and resveratrol partially recovered VD in the ankle and metatarsus joints on these days. These effects may be linked to increased hippocampal neurogenesis and reduced neuroinflammation. The study highlights the benefits of resveratrol and exercise in motor recovery following brain injury, suggesting their potential to enhance the quality of life for patients with neurological disorders affecting motor function and locomotion. These findings also suggest that resveratrol could offer a promising or complementary alternative in managing chronic pain and inflammation associated with orthopedic conditions, thus improving overall patient management.

Refractive index measurements have been an important task for a long time because that index plays an essential role in describing the optical properties of a material. Many methods have been developed to perform that task. Some of them use interferometry to achieve high precision, however these configurations are complicated. Some measure the critical angle using simple structures, but the accuracy is not satisfactory because it is difficult to judge the exact critical angle with intensity variations. Here we propose several new schemes based on measuring the polarization change in the total internal reflection. The proposed method has the merits of simple structure and easy incident angle determination that gives the maximum phase change. Additionally, it is possible to find the material dispersion by measuring the wavelength dependence of the polarization ellipticity. Some useful formulas relating the refractive index with the maximum phase change are obtained. This work can provide valuable alternatives for index measurement.

In the literature, the chemical composition of Rhododendron tomentosum is mainly represented by the study of isoprenoid compounds of essential oil. In contrast, the study of the content of flavonoids will contribute to the expansion of the pharmacological action and the use of the medicinal plant for medical purposes. The paper deals with the technology of extracts from Rhododendron tomentosum shoots using ethanol of various concentrations and purified water as an extractant. Extracts from Rhododendron tomentosum were obtained by a modified method that combined the effects of ultrasound and temperature to maximize the extraction of biologically active substances from the raw material. By the method of high-performance thin-layer chromatography in the system of solvents ethyl acetate: formic acid: water (15:1:1) the following substances have been separated and identified: rutin, hyperoside, quercetin, and chlorogenic acid in all the extracts obtained. To quantify the total flavonoids content, a method of spectrophotometric determination based on the reaction of complexation with aluminum chloride has been developed. It has been proved that the course of the complexation reaction and, accordingly, the quantification of the flavonoid structure substances by the spectrophotometric method is influenced by some factors, including the environment, pH, the structure of the complexes, etc. Regardless of the chosen method, for the further production of Rhododendron tomentosum extracts with a higher content of flavonoid structure substance, it is advisable to use 60%, 70%, and 80% ethyl alcohol as extractant.

A total $m$-labelling $\alpha$ on graph $\Gamma$ is called an edge irregular total $m$-labelling if for any two different edges of $\Gamma$, their weights respect to $\alpha$ are distinct, where the weight of any edge is defined as the sum of its label and the labels of its end vertices. We determine the minimum $m$ such that $\Gamma$ can be labelled by an edge irregular total $m$-labelling whenever $\Gamma$ is an odd staircase graph or an even staircase graph.

Total edentulism is the loss of all teeth for any cause by a multifactorial process that involves biological and patient-related factors. Studies on edentulism and risk factors in Mexico are limited, and the epidemiological surveillance data is scarce and controversial since official governmental reports are not statistically representative of the country. We estimate the distribution for edentulism according to sociodemographic and socioeconomic variables in adults from a low-income state in 2003 and its progress in Mexico. We analyzed data from the National Performance Evaluation Survey in Oaxaca, Mexico, and the annual reports of the Epidemiological Surveillance System of Oral Pathologies in 2009-2019 using X². Oaxacan patients older than 75 y.o (17.9%, p<0.05), those with lower schooling (11.2%), and diabetes (14.5%) presented the highest percentage of edentulism. We do not observe differences in edentulism between sex or residence (p>0.05). From 2009 to 2019, country data reports the lowest rate of edentulism in adults over 20 y.o (0.32%; 95% CI 0.18%-0.48%) and the most affected population over 79 y.o. (7.29%; 95% CI 5.2%-9.30%). As it is a cumulative phenomenon, it is necessary to establish better surveillance, prevention, and treatment programs to improve the oral health of older thus reducing edentulism.

This study aims at the sustainable valorization of eggshells (ES) from different countries of origin in cement concrete as a cement replacement for Hong Kong. For this purpose, sixteen different eggs from different regions across the world were selected from the local market. Firstly, the extent of uniformity in the weight and mineral content of sampled eggshells were assessed by a specific gravity test and thermogravimetric analysis (TGA), respectively. It was found that specific gravity varies between 2.02 and 2.39, with an average value of 2.20 ± 0.01, whereas CaCO₃ varies between 94.65% and 97.23%, with an average value of 96.33%. These values were a bit lower than those of extra-pure limestone (LS) because of the organic part and the porous structure of eggshells. Secondly, three different eggshells were selected for cement replacement in cement concrete, both in the uncalcined and calcined states, based on having the highest, medium, and lowest CaCO₃ content, respectively. To get the calcined eggshells, the eggshells were calcined at 800^oC for three hours. It was found that the strength of eggshells varies with CaCO₃, but the variation was acceptable. The calcined eggshells showed comparatively more compressive strength and were close to the LS because of the free CaO and the absence of an organic part. In general, the variation in the basic properties of eggshells from different regions across the world is negligible and suitable to use as a cement replacement with acceptable variation in strength in Hong Kong.

To explore the characteristics of the concentric eyewall of a typhoon during its formation and replacement processes, with Super Typhoon Muifa in 2011 as the example case, the Weather Research and Forecast (WRF) mode was used to carry out a numerical simulation to reproduce the entire formation and replacement processes of the concentric eyewall. The physical quantities such as the tangential wind speed, radar echo, radial wind speed, vertical wind speed, and potential vortex were diagnosed and analyzed. The results of the analysis show that the outward expansion of the isovelocity in the lower troposphere was the early signal of the formation of the outer eyewall. After the outer eyewall formed, there was a center of second-highest tangential wind speed in the corresponding area. The second-highest wind speed increased as the strength of the outer eyewall increased, and the position of the second-highest wind speed center was retracted with the retraction of the outer eyewall. The tangential wind speed of the moat area was smaller than that corresponding to the concentric eyewall and this feature gradually disappeared with the increase of the height. The echo in the moat area was weak, and this characteristic was particularly evident when the moat area was relatively wide and the outer eyewall was relatively strong. With the formation and development of the outer eyewall, the intensity of the inflow in the boundary layer corresponding to the inner eyewall was reduced, the intensity of the outflow in the upper layers declined, and the intensities of the inflow and outflow corresponding to the outer eyewall were enhanced. After the second outer eyewall matured, there was a significant inflow in the upper layer of the moat area. Once the outer eyewall formed, a large amount of hydrometeors appeared in the corresponding area, and there was a strong ascending motion inside that area. The strength of the ascending motion and the content of hydrometeors increased as the outer eyewall increased. When the moat area was relatively wide, the divergent airflow generated by the developed outer eyewall in the upper layer would produce a significant descending motion in the moat area.

Monitoring and measuring magnesium (Mg) values are essential to prevent the development of numerous complications in perioperative medicine and critically ill patients. Although previous studies suggest that measuring free ionized magnesium (iMg) is more useful for estimating Mg status, clinicians currently rely on measurement of total serum magnesium to determine if supplemental magnesium is needed. In this review, we analyzed the recent literature to decide whether it is better to measure ionized serum Mg or total serum Mg when assessing magnesium status, whether iMg predicts clinical outcome, and what are the difficulties in measuring serum iMg levels in intensive care patients and perioperative medicine.

Biomechanical changes such as increased knee adduction moment (KAM) during walking are known to be involved in the development and severity of knee osteoarthritis (OA). Although various foot progression angle (FPA) modifications during gait have been applied to reduce peak KAM, few studies have investigated effects of applying toe-in or toe-out walking modifications for knee OA on peak KAM and three-dimensional (3D) moments of the ankle joint. Kinetic moment variables were acquired from 35 individuals with medial knee compartment OA. A 3D motion analysis system and two force platforms were used to acquire KAM and 3D moments of both ankle joints during gait. Visual3D motion analysis program was used to obtain final moment data for statistical processing. Repeated-measures analysis of variance with Bonferroni adjustment was used to compare kinetic and kinematic values for each FPA walking condition. The first peak KAM of an internal rotation foot position of the FPA walking condition showed significant decrease compared to normal foot position walking (p &lt; 0.01). The second peak KAM of an external rotation foot position walking showed significant decrease compared to normal foot position walking (p &lt; 0.01). Compared to a normal foot position, peak ankle inversion moment of the external rotation foot position walking showed a significantly decrease (p &lt; 0.05). There were no interactive effects between FPA condition and limb sides for any KAM values (p &gt; 0.05). These results suggest that clinical application of toe-in or toe-out gait modification walking in individuals with knee OA should be performed based on biomechanical evaluations such as peak KAM.

An 8-months old male American Staffordshire terrier was referred for a no weightbearing lameness of the right pelvic limb, hyperthermia, lethargy and inappetence caused by hematogenous osteomyelitis. Orthopedic, radiographic and tomographic examinations revealed a bone sequestrum of 4 x 1.4 cm and active periosteal reaction of the caudo-lateral cortical in the metaphysis and the distal third of the right femoral diaphysis, medullary osteolysis and interruption of the cranio-medial cortical profile, with involvement of the femoral trochlea leading to a secondary medial patella luxation. Once skeletally mature, after 4 months from surgical debridement and aggressive antibiotic therapy against Klebsiella oxytoca revealed by bacteriological exam, the patient underwent prosthetic surgery for the application of a custom-made patellar groove replacement (PGR) to fill the bone defect and restore the femoral trochlea surface. Despite the serious injury that afflicted the right pelvic limb, the surgery had satisfactory outcomes until the last 18-months postoperative follow up.

Aquaculture is growing rapidly as a food-producing sector and in recent years, fishmeal prices have climbed by more than twofold on a global scale. This review of previous studies was performed to contribute to the extant literature on the aquaculture sector to aid cost reduction of aquafeeds by identifying substitute protein that can replace fishmeal. The review followed the Preferred Reporting Items for Systematic Review and Meta-Analyses (PRISMA) using the SCOPUS and WOS (Web of Science), DOAJ (Directory of Open Access Journals), Academia, and Pubmed Central databases with the following search terms: “fishmeal,” “alternative protein source” and “aquafeeds.” This resulted in 5,331 articles from the SCOPUS and WOS databases. Finally, the titles and abstracts of the articles were screened, giving a total of 162 articles that were used in the study; another 58 articles came from open databases. Results have shown that 100% replacement of fishmeal with blood meal did not affect the growth of fish as well as 75% to 100% combination of poultry-by-product (PBM), feather meal (FEM), and blood meal (BM). Moreover, a 10% replacement of fishmeal using seaweed (Gracilaria arcuata) has no adverse effect on feed efficiency and growth performance of tilapia, a 50% replacement of fishmeal using black soldier fly (Hermetia illucens), and 25% replacement using soybean (Glycine max) also showed better results for fish growth. With that, this review shows that alternative protein can be a great alternative to the aquaculture sector in reducing the cost of aquafeeds since alternative proteins are much cheaper than the usual fishmeal.

The main purpose of tissue engineering is to fabricate and exploit engineered constructs suitable for the effective replacement of damaged tissues and organs, and able to perfectly integrate with the host’s organism without eliciting any adverse reaction. Ideally, autologous materials represent the best option, but they are often limited due to the low availability of compatible healthy tissues. So far, one therapeutic approach relies on the exploitation of synthetic materials: they exhibit good features in terms of impermeability, deformability and flexibility, but present chronic risks of infections and inflammations. Alternatively, biological materials, including naturally derived ones and acellular tissue matrices of human or animal origin, can be used to induce cells growth and differentiation, which are needed for tissue regeneration: however, this kind of materials lacks satisfactory mechanical resistance and reproducibility, affecting their clinical application. In order to overcome the above-mentioned limitations, hybrid materials, which can be obtained by coupling synthetic polymers and biological materials, have been investigated with the aim to improve biological compatibility and mechanical features. Currently, the interest in these mate-rials is growing, but the ideal ones have not been found yet. The present review aims at exploring some applications of hybrid materials, with particular mention to urological and cardiovascular fields: in the first case, the efforts to find a construct that can guarantee impermeability, mechanical resistance and patency will be herein illustrated; in the second case, the search for impermeability, hemocompatibility and adequate compliance will be been disclosed.

Asphalt cement will not last for a long time as the world encounters a diminishment in the crude oil. For sustainable, flexible pavement development, new resources can provide a contribution to replace it partially or entirely. In this study, asphalt was partially and entirely replaced by guayule resin as a bioresource by-product, extracted during the guayule natural rubber production. Crumb rubber modifier (CRM) was used as an asphalt enhancer. The Superpave grading system was followed at high, intermediate, and low temperatures to evaluate such innovative binder for rutting, fatigue, and thermal cracking, respectively, in addition to viscosity. Therefore, the original, short-term aging and long-term aging were simulated using tank, rolling thin film oven, and pressure aging vessel materials. Additionally, component analysis using Fourier-transform infrared spectroscopy was provided to link the rheological properties with the chemical changes. Outcomes showed a relatively much lower viscosity of guayule in the same high-temperature asphalt grade indicating savings in plant energy consumption and reduced environmental emissions. CRM enhanced guayule, but not as much as asphalt, proven by polymeric component migration through liquid binder. This enhancement was reflected in the rheological performance besides other factors. As-received guayule seems to have high oxygen content proven by strong absorption peak intensities of oxidative bonds (e.g., Carbonyl and sulfoxide). Such pre-oxidation was negatively reflected in the intermediate- and low-temperature performance of guayule and guayule-based binders. However, the investigated guayule had potential to compensate for asphalt replacement in the presence of CRM by 23–42% by weight of blend.

Objective: Lipids are secreted into milk as bilayer-coated structures: milk lipid globules (MLGs). Adipophilin (ADRP) and perilipin 3 (TIP47) are associated with MLGs in human breast milk; however, the role of these proteins in milk lipid secretion is not fully understood. The aim of the study was to investigate levels of ADRP, TIP47 and total lipid content in human breast milk, their mutual correlations and dynamics during lactation. Research Methods & Procedures: Milk samples from 22 healthy lactating women (Caucasian, Central European) were collected at five time points during lactation (1–3, 12–14, 29–30, 88–90 and 178–180 days postpartum). Mass spectrometry-based method was used for quantification of ADRP and TIP47 in the samples. The gravimetric method was used to determine milk total lipid content. Results: We observed distinctive trends in ADRP, TIP47 levels and lipid content in human breast milk during the first 6 months of lactation. We also found a significant association between lipid content and ADRP, lipid content and TIP47, and ADRP and TIP47 concentrations in breast milk at all sampling points. Moreover, we derived an equation for estimating the mean lipid content of milk based on ADRP concentration in human breast milk. Conclusions: A mass spectrometry-based method was developed for quantifying ADRP and TIP47 in human breast milk. Strong mutual correlations were found between ADRP, TIP47 and total lipid content in human breast milk.