Raru’s plants bark has long been used as traditional medicine in Batak’s tribe. Raru’s bark is derived from several trees that are usually used in a mixture in Batak traditional beverages. This bark is generally used as antidiabetic remedies. This study aims to combine the rarus’s bark extract and mocaf activated-carbon (MAC) in order to study antidiabetics in rats. The combination of raru’s bark extract and MAC were tested on male rats as of Sprague Dawley strain for testing antidiabetic bioactivity. The result showed that antidiabetic activity of raru’s extract and MAC exposed the antidiabetic level declines in rat’s blood. The various treatments of different concentration ratios of raru’s extract and MAC useful in the experiments showed that the levels of blood level reduction were slightly different (14-21%). The raru’s extract pure was observed more effective in decreasing the blood glucose level in rat’s blood, in comparison the positive control. The mixture of raru’s extract and MAC with 75:25 ratio is better than 50:50 ratio. The involvement of MAC in the alleged antidiabetic agent did little in improving the blood glucose level decrease in rat’s blood. Raru’s extract and MAC indicate its potential utilization as an antidiabetic agent.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Reducing the carbon footprint of energy production is one of the most pressing challenges facing humanity today. Lignocellulosic biomass residues from fruit production industries show promise as a viable energy source. This paper presents a study of the Italian context concerning the utilization of orchard lignocellulosic residues for energy production as electricity or bioethanol. The potential of various orchard residues was assessed through chemical and physical analysis, and an equivalent electrical energy of about 6441.62 GWh or an amount of 0.48 Mt/y of bioethanol was obtained based on the average annual dry residue mass availability of about 3.04 Mt/y. These data represent the 9.30% of the national electrical energy production from renewable sources, as well as the 6.21% of the Italian demand for gasoline in 2022. Electricity generation from these residues shown its potential as a reliable and sustainable baseload power source, as well as source of renewable transportation fuel. The studied process could be a valuable reference to expand these concepts on global scale to achieve a greener and more sustainable energy future.

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

(1) Background: The rapid development of information technology has changed the traditional concept of space, gradually shifting the "container space" to the "relational space" . The constraints of geographical spatial elements are diminishing, and the theory of virtual agglomeration is gaining attention. (2) Methods: In this study, we constructed an evaluation system for virtual agglomeration, comprising four primary indicators: virtual infrastructure level, virtual output level, virtual input level, and virtual service level. The TOPSIS method was used to calculate the virtual agglomeration level for each province, and the DEA-Malmquist method was employed to measure provincial total factor productivity (TFP) in China. Using panel data from 30 provincial regions in China from 2013 to 2021, we examined the mechanism and impact path of virtual agglomeration on TFP. (3) Result: There is an inverted U-shaped relationship between virtual agglomeration and TFP in China. The overall development level of virtual agglomeration is relatively low, within the range where the marginal effect of virtual agglomeration on TFP is positive but diminishing, indicating significant potential for further development. The impact of virtual agglomeration on TFP is stronger in the Yangtze River Economic Belt compared to non-Yangtze River areas, and the highest stable point of TFP is higher in central provinces than in eastern and western provinces. (4) Conclusions: This study provides a theoretical basis and practical reference for improving the level of virtual agglomeration .

BACKGROUND Detecting total cholesterol in dried blood spots could aid in identifying individuals with a high likelihood of familial hypercholesterolemia and could be used as a screening measure. This study aims to assess the diagnostic accuracy of dried blood spots on Whatman 903 paper cards using a manual enzymatic technique. METHODS A total of 394 samples collected as serum and dried blood spots were compared. Cholesterol was determined in serum using the automated reference method, while cholesterol on paper was measured using a manual enzymatic method. Within- and between-day diagnostic variability were analyzed. The correlation between both methods was assessed using Passing-Bablok regression and Bland-Altman plot. Internal validation of our correlation formula was performed on 149 samples, along with external validation of the formula proposed by Corso et al. RESULTS The within- and between-day coefficient of variation was found to be lower than 10.14% and 14.09%, respectively. Method comparison yielded an area under the curve of 0.976, with a standard error of 0.009. Passing-Bablok regression indicated a precision of 0.803 and an accuracy of 0.96. Internal validation precision was measured at 0.716. Regarding internal validation, calculated cholesterol with our regression line did not differ from serum cholesterol analysis, while significant differences were observed in calculated cholesterol levels using the external formula. CONCLUSIONS Total cholesterol analysis in dot blood spots demonstrates high precision and reproducibility. This method reliably enables the incorporation of this biological marker into neonatal screening for familial hypercholesterolemia detection.

The world is struggling with the increasing rate at which water bodies are constantly polluted due to rapid modernization and industrialization. The different types of water contaminants include both anthropogenic and natural contaminants. Environmentalists are mainly concerned about heavy metals such as cadmium ions, as they are considered poisonous and carcinogenic even if they are present at a minimum concentration, and they are considered an immediate concern, according to the World Health Organization. Recently, many methods, such as solvent extraction, ion exchange, electrochemical precipitation, and reverse osmosis, have been developed to remove heavy metals from wastewater. These methods have been reported to be expensive and inefficient; hence, more cost-effective and eco-friendly alternative strategies are needed. Amidst these challenges, a ray of hope emerges in the form of biosorbents. These abundant, eco-friendly, and cost-efficient materials have shown promise as an alternative method for removing heavy metals from wastewater. They are equipped with functional groups that can effectively absorb metal ions onto their surfaces, offering a potential solution to our water contamination woes. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The inclusion of spent hemp biomass (SHB), an extracted byproduct from industrial cannabidiol (CBD) production, in the diets of dairy cows and lambs appear to be safe with minor effects on the metabolism, including a decrease of circulating cholesterol and increase bilirubinemia, both associated with liver metabolism. Those effects could be consequence of the presence of cannabinoids, particularly Δ9-tetrahydrocannabinol (THC) and CBD in the SHB. This study aimed to study the transcriptional profile of the liver of dairy cows and lambs fed SHB. Dairy cows received SHB or alfalfa pellet for four weeks of intervention (IP) and four weeks of withdrawal periods (WP). Finishing lambs were fed a control diet (CON), 10% (LH2) or 20% (HH2) SHB for 2 months or 1 month followed by 1-month SHB withdrawal (LH1 and HH1, respectively). RNA sequencing was performed, and the mRNA was annotated using the latest reference genomes. The RNAseq data were filtered, normalized for library size and composition, and statistically analyzed by DESeq2. The bioinformatic analysis was performed by using DAVID, Gene Set Enrichment (GSE) analysis, and the Dynamic Impact Approach. Using a 0.2 FDR cut-off, we identified only ≤24 differentially expressed genes (DEG) in the liver by feeding SHB in dairy cows and a larger number of DEG in lambs (from 71 in HH1 vs. CON to 552 in LH1 vs. CON). The KEGG analysis demonstrated that feeding SHB in dairy cows and lambs had relatively minor to moderate metabolic alterations in dairy cows and lambs mainly associated with amino acids and lipid metabolism whereas cholesterol synthesis was overall activated in lambs. GSE analysis identified activation of PPAR signaling pathway only in dairy cows. We found an opposite effect on activation of metabolism of drug and xenobiotics by cytochrome P450 enzymes in dairy cows and lambs receiving less SHB but an inhibition in HH2 lambs. Immune system-related pathways were inhibited by feeding SHB in lambs, but the impact was minor. Cumulatively, inclusion of SHB containing cannabinoids in dairy and lambs demonstrate very little effects on the alteration of transcriptomic profile of the liver.

This paper introduces a novel method for accurately calculating the upper biomass of single trees using Light Detection And Ranging (LiDAR) point cloud data. The proposed algorithm involves classifying the tree point cloud into two distinct ones: the trunk point cloud and the crown point cloud. Each part is then processed using specific techniques to create a 3D model and determine its volume. The trunk point cloud is segmented based on individual stems, with each stem further divided into slices that are modeled as cylinders. On the other hand, the crown point cloud is analyzed by calculating its footprint and gravity center. The footprint is further divided into angular sectors, with each being used to create a rotating surface around the vertical line passing through the gravity center. All models are represented in a matrix format, simplifying the process of minimizing and calculating the tree’s upper biomass, consisting of crown biomass and trunk biomass. To validate the proposed approach, both terrestrial and airborne datasets are utilized. A comparison with existing algorithms in the literature confirms the effectiveness of the new method. The study shows that the proposed algorithm achieves an average fit between 0.01 m and 0.49 m for individual trees.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

Capabilities of the Attenuated Total Reflection (ATR) at THz wavelengths for increased sub-surface depth characterisation of (bio-)materials is presented. The penetration depth of a THz evanescent wave in biological samples is dependent on the wavelength and temperature and can reach 0.1-0.5 mm depth due to strong refractive index change ∼0.4 of the ice-water transition; this is quite significant and important when studying biological samples. Technical challenges are discussed when using ATR for uneven, heterogeneous, high refractive index samples with possibility of frustrated total internal reflection (a breakdown of the ATR reflection-mode into transmission-mode). Local field enhancements at the interface are discussed with numerical/analytical examples. Maxwell’s scaling was used to model behaviour of absorber-scatterer inside materials at the interface with ATR prism for realistic complex refractive indices of bio-materials. Modality of ATR with polarisation analysis is proposed and its principle illustrated, opening an invitation for its experimental validation. The sensitivity of the polarised ATR mode to the refractive index between the sample and ATR prism is revealed. Design principles of polarisation active optical elements and spectral filters are outlined. The results and concepts are based on experiments carried out at the THz beamline of the Australian Synchrotron.

Kinesiophobia (fear of movement) has been recognized as a significant barrier to recovery and rehabilitation in patients after total knee arthroplasty (TKA). Our goal was to identify predictors of kinesiophobia and examine its correlation with early functional outcomes in TKA recipients. On the first and fifth postoperative days (POD1 and POD5), we evaluated pain using the International Pain Outcomes Questionnaire (IPO-Q) and created multidimensional pain composite scores (PCS). Pain Composite Score-total (PCStotal) assesses the overall impact of pain, taking into account outcomes of pain intensity, pain-related interference with function, and emotions and side effects. Functional status on POD 5 was determined by the Barthel index, 6-minute walking test, and knee range of motion. Kinesiophobia was measured on POD5 using the Tampa Scale for Kinesiophobia (TSK) and multivariable logistic regression was used to assess factors associated with kinesiophobia. Among 75 TKA patients, 27% exhibited kinesiophobia. The final regression model highlighted PCStotal on POD5 (OR=6.2, CI=1.9-19.9), PCStotal (OR=2.1, CI=1.2-3.8) on POD1, and the intensity of chronic pain before surgery (OR=1.4, CI=1.1-2.1) as significant kinesiophobia predictors. On POD5, those with kinesiophobia showed increased dependency, slower gait, and poorer knee extension recovery. This study highlights the importance of identifying and addressing kinesiophobia in TKA patients to optimize functional outcomes and improve recovery. Also, it is important to assess not only pain intensity but also the physical and emotional interference caused by pain, which can contribute to the development of kinesiophobia.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

CO2 emission activity of xylotrophic fungi response to an increase in temperature in the range of 10-30 °C on the example of pure dikaryotic cultures of Fomes fomentarius s. str., F. inzengae, Fomitopsis betulina, F. pinicola, Phellinus igniarius was analyzed. Emission activity was assessed by the difference in CO2 concentration in 0.5-liter exposure chambers with Petri dishes with mycelium growing on agar at the beginning of exposure and an hour later using a Gasmet DX-4030 FTIR spectrometer (Gasmet Technologies Oy, Finland), error measurements ±50 ppm. Specific (μg CO2/cm2/h) and total (μg CO2/h) emission activity and its relationship with temperature and size (area) of the mycelium were assessed. It has been shown that in the range of 10-30 °C, the specific and total CO2 emission activity of the mycelium is closely and positively related to temperature. Specific emission, which is an indicator of the respiratory activity of the mycelium, does not depend on its size; its only driver is temperature, the relationship with which is linear: an increase in temperature by 10 °C causes an increase in the specific emission activity of the mycelium by 1.7 times. The total CO2 emission activity, which is an indicator of the total amount of CO2 emitted, is directly proportional to the specific emission activity and the size of the mycelium. In the range of 10-30 °C, an increase in temperature causes an almost equal increase in both the specific emission activity of the mycelium (Q10 1.7) and its growth (Q10 1.5) and causes an exponential increase in the total emission of CO2. This must be taken into account when predicting CO2 emissions from woody debris under climate change, as it could potentially contribute to accelerating climate change.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

The expanding global population has increased the demand for sustainable protein sources, and microbial protein (MP) has emerged as a promising alternative. However, conventional carbon (glucose) and nitrogen (ammonia, urea) sources needed for MP production pose environmental and economic issues. This study aims to produce protein using lignocellulosic biomass (LCB) as a carbon source and the nitrogen fixation ability of Klebsiella oxytoca M5A1 as a nitrogen source. The study investigates the pretreatment of LCB (switchgrass), enzymatic hydrolysis, protein quantification, and high-performance liquid chromatography system (HPLC) analysis to track glucose utilization and organic acid production. K. oxytoca M5A1 harnessed free nitrogen from the atmosphere through nitrogen fixation and used abundant, cheap glucose from LCB to produce MP and organic acids as by-products. Protein production occurred in two phases: first within the initial 8 hours and secondly, within the last 16 hours. The highest protein concentration was at 40 hours, with approximately 68.3% protein content. HPLC analysis revealed a dynamic profile of glucose utilization and organic acids (Lactic acid, Propionic acid, Acetic acid, and Succinic acid). K. oxytoca M5A1 exhibited an early high rate of glucose consumption, and conversion to organic acids that were later used for second-phase protein production. The acids profile revealed intra-conversion from one acid to another via metabolic pathways (glycolysis and tricarboxylic acid cycle). Overall, leveraging LCB and the nitrogen-fixing ability of K. oxytoca M5A1 for MP production offers an eco-friendly and cost-effective alternative to traditional protein sources, contributing to a sustainable circular economy.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

Accurately estimating shrub biomass in arid and semi-arid regions is critical for understanding ecosystem productivity and carbon stocks at both local and global scales. However, capturing the shrub biomass accurately by satellite observations is challenging due to the short and sparse features of shrubs. In this study, we presented a framework to estimate shrub biomass at a 10m spatial resolution by integrating ground in-situ data, unmanned aerial vehicle (UAV), Sentinel-2, and Sentinel-1 observations. The pilot study was conducted in the Helan mountains of Ningxia province, China. First, the spatial distribution map of shrubland and other land cover types was generated in 2023. Then, a prediction model of shrub biomass was developed in a Random Forest Regression (RFR) approach driven by different predicted variable datasets based on in-situ measurements, UAV, and satellite images. Finally, the developed model was used to produce the biomass map of shrubland in 2023. The uncertainty was characterized by creating a standard deviation (SD) map using the Leave-One-Out Cross-Validation (LOOCV) method in the shrub biomass estimates. The resultant shrubland distribution map in 2023 has an F1 score of 0.92. The shrub biomass model driven by spectral bands and vegetation indices (R2= 0.62) demonstrated superior performance than that only driven by spectral bands (R2=0.33) or vegetation indices (R2=0.55). The uncertainty of the estimated biomass was lower than 4%, with the lowest values (<2%) happening in the high shrub coverage (>30%) and biomass production (>30kg/m2) regions. Furthermore, the findings show that the magnitude of shrub biomass was affected by the aridity and precipitation significantly in the study region. This study provides a workflow to accurately monitor the biomass of shrublands in a complicated environment based on remote sensing images from multi-platform observations.

At the end of the dry season in early March to early April each year, extensive agricultural biomass waste burnings occur throughout insular mainland Southeast Asia. During this biomass burnings period, smoke aerosols blanket the whole regions and were transported and dispersed by predominant westerly and south westerly winds to southern China, Taiwan and as far southern Japan and the Philippines. The extensive and intense burnings coincided with some wildfires in the forests due to high temperature making the region one of the global hot spots of biomass fires. In this study, we focus on the effect of pollutants emitted from biomass burnings in March 2019 at the height of the burnings period to the exposed population and their health impact. The Weather Research Forecast- Chemistry (WRF-Chem) model was used to predict the PM2.5 concentration over the simulating domain and health impacts are then assessed on the exposed population in the four countries of Southeast Asia, namely Thailand, Laos, Cambodia and Vietnam. Using the health impact based on log-linear concentration response function and Integrated Exposure Response (IER), the results show that at the peak period of the burnings from 13 to 20 March 2019, Thailand experienced the highest impact, with an estimated 2170 premature deaths. Laos, Vietnam, and Cambodia followed, with estimated mortalities of 277, 565, and 314 deaths respectively. However, when considering the impact per head of population, Laos exhibited the highest impact, followed by Thailand, Cambodia, and Vietnam. The results highlight the significant health impact and associated economic cost of agricultural waste burnings in Southeast Asia at the end of the dry season. And hence policy makers should take these into account to design measures to reduce the negative impact of widespread burnings on exposed population in the region.

The Loess Plateau is an important region for vegetation restoration in China, however, changes in soil organic carbon (SOC), soil nutrients, and stoichiometry after restoration in this vulnerable ecoregion are not well understood. Typical restoration types, including orchardland (OL), grassland (GL), shrubland (SL), and forestland (FL) were chosen to examine changes in the stocks and stoichiometry of SOC, soil total nitrogen (TN), and soil total phosphorus (TP) at different soil depths and recovery times. Results showed that SOC stocks first increased and then stabilized in OL, GL, and SL at 0–30 cm depth, while in FL, stocks gradually increased. Soil TN stocks first increased and then decreased in OL, SL, and FL with vegetation age at 0–30 cm depth, while soil TP stocks showed little variation between restoration types. In the later stages of restoration, the stocks of SOC and soil TN at 0–30 cm soil depth were still lower than those in natural grassland (NG) and natural forest (NF). The overall C:N, C:P, and N:P ratios increased with vegetation age. Additionally, the SOC, soil TN and soil TP stocks, and C:N, C:P, and N:P ratios decreased with soil depth. The FL had the highest rate of change in SOC and soil TN stocks, at 0-10 cm soil depth. These results indicate a complex response of SOC, soil TN, and soil TP stocks and stoichiometry to vegetation restoration, which could have important implications for understanding C, N, and P changes and nutrient limitations after vegetation restoration.

A novel domination invariant defined by Boutrig and Chellali in the recent: total vertex-edge domination. In this paper we obtain an improved upper bound of total vertex edge-domination number of a tree. If is a connected tree with order , then with and we characterize the trees attaining this upper bound. Furthermore we provide a characterization of trees with

Worldwide, different strategies are elaborated in order to ensure optimum conditions for the development and growth of the economic competitiveness, but also for increasing the quality of life and environment protection. All these strategies are closely linked with the development and modernization of the systems for producing energy from clean and renewable sources. In this context, the present paper presents the results of the researches regarding the evaluation of the sustainability of the briquettes production, using the biomass resulted from vine winter pruning as raw material. An analysis of the scientific references indicates that nearly 8 Mt of biomass result from over 7.4 million hectares of vine plantations existent worldwide, biomass that could be valorized through densification in order to produce solid biofuels with a lower calorific value of more than 17 MJ·kg-1. When designing the scientific endeavor, the following aspects were considered: defining the aim and objectives of the research; design of the research algorithm; collection, preparation and conditioning of the biomass; chemical analysis of the briquettes; evaluation of the technological characteristics of the briquettes; evaluation of the energy consumption and energy efficiency for producing the briquettes, taking into account two drying methods (natural and artificial drying). In the meantime, some specific laboratory equipment was design and built for the artificial drying of biomass, evaluation of the mechanical durability, measurement of the energy consumption etc. The analysis of the experimental data has led to the conclusion that the agricultural waste from vine pruning can constitute an important and sustainable source of energy in the form of bri-quettes, which fulfill most of the requirements imposed by the international standards.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

Immortal-time bias (ITB) is known to be common in cohort studies and distorts the association estimates between treated and untreated groups. We used data from the last of two large studies in an Italian province on COVID-19 vaccines safety and effectiveness incurred this bias, and aligned the entire population on a single index date, to correct the ITB. We considered the "all-cause deaths" outcome to compare the survival curves between the unvaccinated group and the various vaccination statuses. The all-cause deaths Hazard Ratios in univariate analysis for unvaccinated (reference) versus vaccinated with 1, 2, 3/4 doses were 0.88 (CI95: 0.78 –1.00; p-value 0.044), 1.23 (1.16–1.32; p-value ≤0.001) and 1.21 (1.14–1.29; p-value ≤0.001), respectively. The multivariate values were 2.40 (2.00–2.88; p-value <0.0001), 1.98 (1.75–2.24; p-value <0.0001), 0.99 (0.90–1.09; ns). The possible explanations of the trend of the Hazard Ratios as vaccinations increase could be a harvesting effect; a calendar-time bias, accounting for seasonality and pandemic waves; a case-counting windows bias; a healthy-vaccinee bias; or some their combination. With two and even with 3/4 doses the calculated Restricted Mean Survival Time and Restricted Mean Time Lost have shown a small but significant downside for the vaccinated populations.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

A non-destructive analysis of proximate parameters (moisture content, MC; volatile matter, VM; fixed carbon, FC; and ash content) for a variety of chipped and ground biomasses was investigated through a combination of thermogravimetric analysis (TGA) and near-infrared spectroscopy (NIRS) with partial least squares regression (PLSR). In this study, the thermogravimetric method was employed as a tool to determine the proximate analysis data of biomass samples through TG and DTG curves, which were generated by tracking changes in biomass mass loss over time or temperature. NIRS non−destructively scanned the chipped biomass in diffuse reflectance while ground biomass using transflectance mode, covering the wavenumber range of 3594.87 to 12,489.48 cm−1. The PLSR−based models: Full−PLSR, genetic algorithm (GA)−PLSR, successive projection algorithm (SPA)−PLSR, the spectral multi−preprocessing (MP) PLSR− 5 range method, and the MP PLSR−3 range method were developed. Model performance was assessed, compared, and selected based on the coefficient of determination in the prediction set (R2P), root mean square error in the validation set (RMSEP), and the ratio of prediction to deviation (RPD). Based on the comprehensive analysis of model performance, MC and FC models of chip biomass have demonstrated satisfactory performance which makes it applicable cautiously in any application, including research. The optimum models for MC and FC in chip biomass were constructed using GA−PLSR with 2nd derivative and Full−PLSR with a constant offset, resulting in R2P values of 0.8654 and 0.8773, RMSEP values of 0.85% and 2.12%, and RPD values of 2.9 and 3.0, respectively. Other parameters such as MC and FC in ground biomass as well as VM and ash content in both chip and ground biomass were found suitable for rough screening. The sensitivity of the selected model was assessed by calculating the limit of quantification (LOQ), and the results indicated that the calculated LOQ values for VM in both chip and ground biomass and FC in chip biomass are lower than the minimum reference values used during model development, signifying a high level of sensitivity. However, for the remaining parameters, the LOQ values surpass the established minimum reference value, suggesting the model could not predict the future samples with reference value lower than the calibration range. Nevertheless, enhancing the models by incorporation an ample number of representative biomass samples and consistently validating the models with unknown samples is imperative to ensure accurate predictions.

A proportion of osteoarthritis (OA) patients are unsatisfied with post-operative outcomes following total joint replacement surgery (TJR), with insufficient pain relief or poor functional improvement. Predicting those will have poor outcomes would be beneficial for patients and clinicians. The aim of this study was to determine the relationship between baseline anthropometric data and the concentration of pre-operative serum and peri-operative synovial fluid (SF) cytokines with 7-month post-operative outcomes in a cohort of knee and hip OA patients. 160 OA patients were recruited who were scheduled for TJR. The concentration of 24 cytokines were measured in blood and SF by multiplex assay. EQ5Dindex health status was assessed pre-operatively and at 7-months post-operatively. 13% of patients were identified as non-responders based on EQ5Dindex. Compared to responders, non-responders were of higher BMI, had greater waist and hip circumference and had higher levels of SF leptin but lower levels of SF Resistin (p&lt;0.05). Linear regression analysis found a significant relationship between pre-operative body weight and post-operative response (ΔEQ5Dindex; r=0.222, p=0.049). The combination of body weight with SF amphiregulin and SF IL-6 provided an improved predictive model of post-operative response (r=0.470, p=0.035).

Driven by mounting environmental apprehensions stemming from the over dependence on fossil fuels in energy and transportation sectors, extensive exploration into alternative energy sources, particularly biomass, has stimulated profound research on harnessing the potential of computational and mathematical techniques. This comprehensive survey delves into optimal models and strategies, unveiling their pivotal role in the design of biomass gasification processes.of hydrogen through biomass gasification. In this study, we aim to provide a comprehensive overview of the computational and mathematical techniques employed in optimizing biomass gasification processes, with a specific focus on enhancing hydrogen yield. Through an extensive literature review, various models and strategies will be examined, including thermodynamic analysis, kinetic modeling, reactor design, and process optimization. By uncovering the power of these techniques, we aim to contribute to the advancement of sustainable and efficient biomass utilization for the hydrogen-based future economy.This paper aims to provide an updated and comprehensive coverage of the investigations conducted on the potential of producing hydrogen from biomass through gasification. To achieve this, we incorporate the latest works that have utilized numerical modeling, simulation, optimization techniques, process heat integration, and co-generation in their studies. By encompassing these aspects, we aim to offer a broader and more in-depth re-appraisal of the subject matter. This will ensure that readers gain a holistic understanding of the advances made in the field and the potential for sustainable hydrogen production of biomass gasification.Through a meticulous re-appraisal and analysis of each subject, we can identify their respective strengths and areas that require further research effort. By thoroughly examining numerical modeling, simulation, optimization techniques, process heat integration, and co-generation, we can assess their effectiveness and applicability in the context of biomass gasification for hydrogen production. This analysis shed light on the areas where these techniques excel, as well as pinpoint limitations or gaps in current understanding. By identifying these areas, we can highlight the need for further research and development, enabling us to make significant advancements in biomass gasification processes and pave the way for a sustainable and efficient hydrogen-based future economy..

Nowadays, the high demand for healthy foods and sustainable products, has led the food industry to explore innovative food technologies, such as fortification with bioactive compounds like antioxidants and polyphenols, that may be sourced from herbs or by-products. The aim of the present study was to explore the enrichment of refined olive oils with natural bioactive compounds such as the herbs rosemary (salvia rosmarinus), basil (ocimum basil), sage (salvia officinalis), lemon balm (melissa oficinallis), st. john’s wort (hypericum perforatum), pink savory (Thymbra satureja), dittany (origanum dictamnus), and by-products such as pomace from olives, olive leaves (olea europaea tree), orange peel (citrus sinensis), lemon peel (citrus limon), pomegranate peel (punica granatum) and mandarin peel (citrus reticulate). The fortification of the refined olive oils was performed with the use of different methodologies such as Conventional maceration (CM), Incubation shaking maceration (ISM), and Ultrasound assisted maceration (UAM). Their phenolic content and antioxidant capacity were measured with Folin–Ciocalteu assay and Ferric Reducing Antioxidant Power (FRAP) assay respectively. All methods demonstrated that different parameters such as time of maceration, temperature and sample concentration, play an important role in the fortification process of the refined olive oils. The predicyed bioavailability of the antioxidant and phenolic compounds in the fortified oils was determined with in vitro digestion and ranged from 4.84% to 53.11%. Furthermore, the refined olive oils fortified with pomace, basil, st. john's wort, and pomegranate peel presented the highest antioxidant and phenolic predicted bioavailability indices during the in vitro process compared to the control refined olive oil. Finally, fortification with natural herbs or by-products can be considered an innovative method for the improvement of the nutritional value of refined olive oils.

Lignocellulosic biomass has garnered attention as an abundant and sustainable alternative energy source that can facilitate reliable and environmentally friendly energy generation. Energy security improves, and environmental impacts diminish when bioethanol, a biofuel produced via lignocellulose-based processes, is utilized. The lignocellulosic biomass of Thysanolaena latifolia has considerable potential as a bioethanol feedstock due to its high carbohydrate content (62.4 ± 0.7%). In this study, feedstock derived from T. latifolia was pretreated with various concentrations of H3PO4 to determine the ideal conditions for enzymatic hydrolysis to convert the feedstock to fermentable sugar. The findings revealed that hydrolysis efficiency and glucose recovery yields were substantially improved compared to those of the untreated sample. Pretreated samples were enzymatically digested to produce a liquid hydrolysate. This hydrolysate was fermented without detoxification using Saccharomyces cerevisiae TISTR 5339 to produce ethanol. The results indicated that T. latifolia biomass hydrolysate is a promising long-term carbon source for ethanol production from cellulosic biomass. Furthermore, the morphological and crystallographic characteristics of the treated T. latifolia biomass were influenced by H3PO4 concentration, as indicated by the SEM images, X-ray diffractogram patterns, and crystallinity index values. Therefore, utilizing T. latifolia feedstock to produce bioethanol can enhance bioenergy sustainability.

This study investigates the trends and patterns of robotic-assisted total knee arthroplasty (RA-TKA) from 2016 to 2019. Using data from the Nationwide Inpatient Sample (NIS), we analyzed demographics, prevalence of comorbidities, total cost, and length of stay (LOS) for 88,415 RA-TKA cases identified during this period. Our analysis revealed a significant increase in RA-TKA procedures, from 5,330 in 2016 to 39,495 in 2019. Patients undergoing RA-TKA were slightly younger, with an average age of 66.2 years. The average hospital stay was 1.89 days, and total charges averaged $65,891. We also examined various comorbidities and demographic factors, including race, median household income, and hospital teaching status. The results show that RA-TKA usage in the US has grown substantially, with specific demographic and clinical patterns. Further studies on the long-term outcomes of RA-TKA are needed to fully understand the benefits of this technology.

Background: Recent disasters have demonstrated gaps in employers’ preparedness to protect employees and promote their well-being in the face of emergencies and disasters affecting the workplace and their communities. Total Worker Health (TWH), a comprehensive perspective developed by the National Institute for Occupational Safety and Health, is a helpful framework for addressing employer preparedness. It includes attention to health and safety at work, and the promotion of the health and well-being of the employee in the context of social determinants of health, such as work-life balance. Methods: TWH concepts, including the domains of TWH and the TWH Hierarchy of Controls, were investigated for their relevance to protecting employees and promoting their well-being during and after crises such as weather disasters, pandemics, and acts of terrorism. Building upon TWH concepts, an employer preparedness framework and model is proposed. Findings: The Model emphasizes upstream prevention, workplace-community linkages, social and economic impacts, and employer leadership through a cyclical planning process. Conclusions/Application to Practice: The Model can assist employers in advancing their preparedness for all hazards through self-assessment and planning agendas based upon the proposed domains.

Hydrogen is undoubtedly one of the most promising alternatives for generating energy with low environmental impact. However, most hydrogen produced today is derived from fossil fuels, which negatively impacts the environment. In this context, biomass conversion technologies emerge as a sustainable and environmentally friendly alternative to conventional fossil-based processes for hydrogen production. The main objective of this study is to underscore the potential of biomass-derived hydrogen, as one of the key sustainable energy solutions. This work reviews diverse biological and thermochemical pathways for biomass-derived hydrogen production, noting challenges in technology and feedstock diversity. Biomass offers local availability and economic benefits, potentially yielding negative emissions. Biological methods like bio-photolysis and fermentation promise low-energy, waste-recycling solutions despite operational constraints. Thermochemical processes, influenced by biomass type and energy content, favor economies of scale and conventional gasification for economic viability. Hydrothermal gasification shows promise for high-moisture feedstocks. Overall, while thermochemical processes suit centralized large-scale hydrogen production, biological pathways offer decentralized options, necessitating continued innovation for integration into future energy strategies.

The use of biomass as a source of energy has been identified to be energy intensive which involves high cost of handling. However, pelletization reduces the bulk density of biomass, thereby reducing the cost of handling and enhancing ease of use. This study modified and evaluated an existing hand operated fish feed pelleting machine. The parts of the machine that were redesigned are hopper and power transmission unit. Corncob was used to evaluate the modified machine using die hole diameter (5,6 and 7 mm) and binder quantity (0, 2.5 and 5 wt%) as factors. The average results obtained for machine efficiency, throughput, pellet length and bulk density were 58.83%, 4.24 kg/h, 15.51 mm and 0.160 g/cm3. Die hole diameter had significant effect on pellet length only. Binder quantity had significant effect on machine efficiency, throughput and pellet length. Machine efficiency and throughput reduces as the quantity of binder increases and pellet length increases with increasing quantity of binder.

Objective: To examine the effect of bilateral total lobectomy and unilateral total lobectomy on improving thyroid function in patients with thyroid micropapillary carcinoma treated with euthyrox. Methods: The study was conducted on 68 patients with thyroid micro papillary carcinoma treated with euthyroxwho had been surgically treated with euthyrox in our hospital between January 2018 and December 2019. On the basis of random number grouping, they were divided into control groups (n = 34, bilateral total lobectomy) and observation groups (n = 34, unilateral total lobectomy plus isthmectomy). Thyroid function, free triiodothyronine (FT3), thyroid hormone (TSH), and voice function (VHI score) of the two groups were compared.Results: In comparison to the control group, the observation group had shorter incision lengths, shorter operation times, and shorter hospital stays, as well as less intraoperative bleeding and drainage volume, and the difference was statistically significant (P < 0.05); As compared with the control group, the observation group had higher FT4 and FT3 levels as well as lower TSH levels, a statistically significant difference (P < 0.05).VHI scores of emotions, function, physiology, and other voice functions were significantly lower among the observation group than those of the control group (P < 0.05).Conclusion: A unilateral total lobectomy with adjacent isthmus resection in patients with thyroid micro papillary carcinoma can yield ideal results, accelerate the time taken for surgical rehabilitation, improve thyroid function, thereby improving voice quality, as well as improve the overall prognosis of the patient.

In the context of autosomal dominant polycystic kidney disease (ADPKD), total kidney volume (TKV) plays a key role as biomarker of disease progression and response to therapy and has been recently recognized as enrichment biomarker and possible surrogate endpoint. Several imaging modalities and methods are available to calculate TKV, and the choice depends on the purpose of use. Technological advancements have made it possible to accurately assess cyst burden, that can be crucial to assess the disease state and help identifying rapid progressors. Moreover, the development of automated algorithms has increased the efficiency of total kidney and cyst volume measurements. Beyond total kidney and cyst volume, the quantification and characterization of non-cystic kidney tissue show potential to early stratify ADPKD patients, monitor disease progression, and possibly predict renal function loss. A broad spectrum of kid-ney MRI techniques are available to characterize kidney tissue, showing promise to non-invasively pick up early signs of ADPKD progression. Radiomics has been used to extract tex-tural features from ADPKD images, providing valuable information about the heterogeneity of the cystic and non-cystic components. This review provides an overview of ADPKD imaging bi-omarkers, focusing on quantification methods, potential, and necessary steps towards successful translation to clinical practice.

The present study aimed at utilizing technically hydrolyzed lignin (THL), industrial biomass residue, derived in high-temperature diluted sulphuric acid hydrolysis of softwood and hardwood chips to sugars. The THL was carbonized in horizontal tube furnace at atmospheric pressure, in inert atmosphere and at three different temperatures (500, 600 and 700 ºC). Biochar chemical composition was investigated along with its HHV, thermal stability (thermogravimetric analysis) and textural properties. Surface area and pore volume were measured with nitrogen physisorption analysis often named upon Brunauer–Emmett–Teller (BET). Increasing the carbonization temperature reduced volatile organic compounds (40 ÷ 96 wt. %), increased fixed carbon (2.11 to 3.68 times the wt. % of fixed carbon in THL), ash and C-content. Moreover, H and O were reduced, while N- and S-content were below the detection limit. This suggested biochar application as solid biofuel. The biochar Fourier-transform infrared (FTIR) spectra revealed that the functional groups were gradually lost thus, forming materials having merely polycyclic aromatic structures and high condensation rate. The biochar obtained at 600 and 700 ºC proved having properties typical for microporous adsorbents, suitable for selective adsorption purposes. Based on the latest observations another biochar application was proposed - as catalyst.

The focus of our study was the changes in the composition of semi-natural dry grasslands in Hungary. Since these valuable habitats were created with the help of humans, their preservation also requires regular treatment. Our mowing experiment aimed to investigate the suppression of the native Calamagrostis epigejos L. Roth. In Hungary, in the Cserhát Mountains, eight permanent plots were mowed twice a year. The vegetation was sampled annually between 2001 and 2011. The effects of mowing were investigated with repeated measures analysis of variance (ANOVA). After 10 years, the C. epigejos cover of the mowed plots decreased significantly, from the initial average of 62.38 to 7.50%. Surprisingly, we also experienced a similar decrease in the control plots. Regular treatment also had a positive effect on the number of species and diversity. Species richness increased continuously in both treatment types, which indicates the combined effect of vegetation succession and treatment. The biomass growth of other Poaceae and Fabaceae species, which are important from a grassland management perspective, was also facilitated by mowing. Our results suggest that long-term in situ experiments and continuous botanical studies are needed to establish a reliable utilization of grasslands.

Considerable amounts of agro-industrial by-products are discarded or burnt as fuel every year. However, they can be utilized as a valuable source of fiber, phenolics and other useful compounds such as antioxidants. The profile of beneficial compounds can be affected by genotype, locality, orchard management and productive season, adding or decreasing the bioactive potential of by-products. In this study, hazelnut (Corylus avellana L.) and walnut (Juglans regia L.) nutshells were investigated for their fiber content and antioxidant capacity as valorized by-products for the industry. Determinations (ORAC, TPC and color asses) were performed in hazelnut and walnut orchards located in Southern Chile during three consecutive seasons (2020/21; 2021/22 and 2022/23). Analyses of oxygen radical absorbance capacity (ORAC) in nutshells showed the highest ORAC from both species in the season 2020/21 (3217 µmol TE g1DW for hazelnut shells and 4663 µmol TE g DW1 for walnut shells), while variability in the consecutive seasons was lower for hazelnut than in walnut. Total phenolic content in hazelnut shells was positively correlated with L* (R: 0.883) and E (R: 0.924) during 2020/21 season, also with L* for 2022/23 (R: 0.907). While ORAC was negatively correlated with L* (R: 0.922) in 2021/22. In addition, morphological and structural features of both nutshells examined by Scavenging Electron Microscopy (VP-SEM) and Confocal Scavenging Laser Microscopy (CSLM) revealed differential tissue distribution and accumulation patterns of both cellulose and lignin. On the other hand, photo-colorimetric values were determined for both shells and corresponding seasons, and non-significative differences were found both shells and among seasons Finally, these results provide insight into the physicochemical characteristics of two shell types which should be considered together with antioxidant capacity in their valorization as a residual material.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

The production of biomass fly ash has been increasing every year in Europe, reaching 5.5 million tons in 2020. Biomass fly ash is not yet accepted in the standards as a substitute material for cement in mortar and concrete. In a first approach, the substitution limit of biomass fly ash is determined by comparing the mechanical strengths, fresh state properties and hardened properties of mortars produced with biomass fly ash to those of mortars produced with classical coal fly ash. Then, masonry and rendering mortars have been designed with different substitution rates of biomass fly ashes from wood combustion in thermal power plant. Although there is an overall decrease in performance, mortars made with biomass ash retain properties that make them suitable for use in masonry or rendering.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

In different fields in our life, like physics, coding theory and computer science, graph labeling dramas an vital role and appears in many applications. A labeling of a graph is a map which assign each element in with a positive integer number. An edge irregular total -labeling is a function such that where and are weights for any two distinct edges. In this case, has total edge irregularity strength (TEIS) if is minimum. In our paper, we defined a new type of graphs called a triple star snake graph and star snake graph . Also, we investigated TEIS for a triple star snake graph . After that, we generalized the results for star snake graph .

Total hip arthroplasty is a complex procedure. The achievements of implantology enabled the development of a faithful representation of hip joint physiology as well as the production of materials that can successfully replace damaged natural tissues. A very important issue is the correct selection of the geometry of the endoprosthesis adequate to the load of the joint. Materials used for endoprosthesis are a metal head and a polymer cup (e.g. PE-UHMW). The main interactions in the endoprosthesis are friction and surface pressure, which must be limited, exceeding them causes the destruction of the biomechanical system - plastic deformation of the polymer and the formation of too large and unacceptable radial clearances. Based on the author's developed calculation method of hip joint endoprosthesis contact parameters, the impact on maximum contact pressure and the angle of contact of the joint load was estimated depending on the diameter of the endoprosthesis and radial clearance. The correctness of changing the values of maximum contact pressure from the mentioned parameters was determined. Correspondingly: an increase in joint load causes a linear increase in the maximum contact pressure; increasing the diameter of the endoprosthesis head - their non-linear decrease, and increasing radial clearance - their increase

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

The reagents and raw materials used, as well as the products obtained (bio-oil, reaction condensates, polyols and sugar phases) were characterized by elemental analysis, infrared spectroscopy, thermogravimetry and high performance liquid chromatography with mass spectrometry. The heating value of the bio-oils is higher than that of the original biomass (higher heating value of Eucalyptus sawdust bio-oil 29 MJ/kg versus 19.5 MJ/kg of the original Eucalyptus sawdust). The analyses of the bio-oils allowed to identify the presence of high added-value compounds, such as levulinic acid and furfural. Finally, a study of the accelerated aging of the liquefied biomass showed that the biofuel density increases with the storage time due to the occurrence of repolymerization reactions.

Bifunctional catalysts consisting of mono- or bimetallic nanoparticles (NPs) and zeolite supports received considerable attention due to excellent catalytic properties in numerous reactions including direct and indirect biomass processing. Here, we discuss major approaches to the preparation of NPs in zeolites, concentrating on methods allowing the best interplay (synergy) between metal and acid sites which is normally achieved for small NPs well-distributed through zeolite. We focus on modification of zeolites to provide structural integrity and controlled acidity which can be accomplished by incorporation of certain metal ions or elements. The other modification avenue is the adjustment of the zeolite morphology including creation of numerous defects for the NP entrapment and designed porosity. In this review we also provide examples of synergy between metal and acid sites and emphasize that without density functional theory calculations many assumptions about interactions between active sites stay unvalidated. Finally, we describe the most interesting examples of direct and indirect biomass (waste) processing for the last five years.

Wetlands are carriers of metals and organic pollutants from natural and anthropogenic sources. Studies have shown that sediments are sinks for these pollutants as they carry more than 99% of the total amount of metals which are released as soluble metals into the Lagoon. The University of Lagos, located at Akoka North eastern part of Yaba in Lagos Mainland runs along a highly industrialized and residential area. This paper reports the total metal concentrations in wetland and sediment and their seasonal variations. Wetland and sediment samples were collected for two seasons in 8 sampling sites. Results showed wetland data having lower concentrations of metals as compared to sediments. Wet season had higher concentrations of metals as compared to other season. Total concentrations in wetlands were Cd (1.0-6.0), Cu (1.0-11.0), Cr (0.3-82.7), Zn (2.7-65.0) and Pb (0.3-16.0) all in μg L-1 respectively. Statistical analysis showed that there was a significant difference between the wet and dry seasons for sediments. Cd was the only metal at acceptable levels while Cr, Cu, Pb and Zn concentrations all exceeded levels deemed acceptable by the SABS and the EPA. Therefore, the wetland is in poor health.

Wet anaerobic storage of algal biomass is a promising preservation approach which can ensure continuous supply of these feedstocks to biorefineries year-round. An effective solution to preservation must ensure minimal dry matter loss and change in biochemical composition during storage. Therefore, the objective of this study was to investigate the preservation of Nannochloropsis gaditana biomass through wet anaerobic storage and its impact on biomass quality. Prior to storage, algae sample was inoculated with two different strains of lactic acid bacteria and thereafter stored for 30 and 180 days. Each inoculant limited dry matter loss to &lt;10% (dry basis) after the storage durations. Final pH values (4.3 - 4.8) indicate that the biomass samples were properly ensiled, achieving the acidic conditions necessary for preservation. Compositional analysis of the biomass after storage showed a reduction in carbohydrate content, a relative increase in lipid content, and no significant change to the protein fraction. Glucose and galactose were the prevalent sugar monomers. The low dry matter loss and minimal compositional change indicates that wet anaerobic storage is an effective means of preserving algal biomass, ensuring a constant supply of algal biomass feedstock to a biorefinery.

In the end, this paper analyzed the economy from the investment in plant construction, raw material collection, product production and product sales. The resulting products include pyrolytic carbon, pyrolytic oil, pyrolysis gas. The results showed that when the treatment scale was 1 ton h−1, the pyrolysis plants with three loading modes will always be in a state of loss during the 20-year running time. When the processing scale was 9 ton h−1, the pyrolysis plant can be profitable in the first year. In the sensitivity analysis, the influence of three pyrolysis products on the total return on investment was explored. The results showed that the price change of pyrolysis oil has the greatest influence on the total return on investment (Total ROI) under the three loading methods, The price change of pyrolysis gas has minimal impact on the Total ROI. This study provides basic data and basis for the commercialization of coal-biomass co-pyrolysis technology and investment in plant construction.

Net CO2 emissions and sequestration from European forests are the result of removal and growth of flora. To arrive at aggregated measurements of these processes at a country's level, local observations of increments and harvest rates are up-scaled to national forest areas. Each country releases these statistics through their individual National Forest Inventory using their particular definitions and methodologies. In addition, five international processes deal with the harmonization and comparability of such forest datasets in Europe, namely the IPCC, SOEF, FAOSTAT, HPFFRE, FRA (definitions follow in the article). In this study, we retrieved living biomass dynamics from each of these sources for 27 European Union member states. To demonstrate the reproducibility of our method, we release an open source python package that allows for automated data retrieval and analysis, as new data becomes available. The comparison of the published values shows discrepancies in the magnitude of forest biomass changes for several countries. In some cases, the direction of these changes also differ between sources. The scarcity of the data provided, along with the low spatial resolution, forbids the creation or calibration of a pan-European forest dynamics model, which could ultimately be used to simulate future scenarios and support policy decisions. To attain these goals, an improvement in forest data availability and harmonization is needed.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

Refractive index measurements have been an important task for a long time because that index plays an essential role in describing the optical properties of a material. Many methods have been developed to perform that task. Some of them use interferometry to achieve high precision, however these configurations are complicated. Some measure the critical angle using simple structures, but the accuracy is not satisfactory because it is difficult to judge the exact critical angle with intensity variations. Here we propose several new schemes based on measuring the polarization change in the total internal reflection. The proposed method has the merits of simple structure and easy incident angle determination that gives the maximum phase change. Additionally, it is possible to find the material dispersion by measuring the wavelength dependence of the polarization ellipticity. Some useful formulas relating the refractive index with the maximum phase change are obtained. This work can provide valuable alternatives for index measurement.

In the literature, the chemical composition of Rhododendron tomentosum is mainly represented by the study of isoprenoid compounds of essential oil. In contrast, the study of the content of flavonoids will contribute to the expansion of the pharmacological action and the use of the medicinal plant for medical purposes. The paper deals with the technology of extracts from Rhododendron tomentosum shoots using ethanol of various concentrations and purified water as an extractant. Extracts from Rhododendron tomentosum were obtained by a modified method that combined the effects of ultrasound and temperature to maximize the extraction of biologically active substances from the raw material. By the method of high-performance thin-layer chromatography in the system of solvents ethyl acetate: formic acid: water (15:1:1) the following substances have been separated and identified: rutin, hyperoside, quercetin, and chlorogenic acid in all the extracts obtained. To quantify the total flavonoids content, a method of spectrophotometric determination based on the reaction of complexation with aluminum chloride has been developed. It has been proved that the course of the complexation reaction and, accordingly, the quantification of the flavonoid structure substances by the spectrophotometric method is influenced by some factors, including the environment, pH, the structure of the complexes, etc. Regardless of the chosen method, for the further production of Rhododendron tomentosum extracts with a higher content of flavonoid structure substance, it is advisable to use 60%, 70%, and 80% ethyl alcohol as extractant.

A total $m$-labelling $\alpha$ on graph $\Gamma$ is called an edge irregular total $m$-labelling if for any two different edges of $\Gamma$, their weights respect to $\alpha$ are distinct, where the weight of any edge is defined as the sum of its label and the labels of its end vertices. We determine the minimum $m$ such that $\Gamma$ can be labelled by an edge irregular total $m$-labelling whenever $\Gamma$ is an odd staircase graph or an even staircase graph.

Total edentulism is the loss of all teeth for any cause by a multifactorial process that involves biological and patient-related factors. Studies on edentulism and risk factors in Mexico are limited, and the epidemiological surveillance data is scarce and controversial since official governmental reports are not statistically representative of the country. We estimate the distribution for edentulism according to sociodemographic and socioeconomic variables in adults from a low-income state in 2003 and its progress in Mexico. We analyzed data from the National Performance Evaluation Survey in Oaxaca, Mexico, and the annual reports of the Epidemiological Surveillance System of Oral Pathologies in 2009-2019 using X². Oaxacan patients older than 75 y.o (17.9%, p<0.05), those with lower schooling (11.2%), and diabetes (14.5%) presented the highest percentage of edentulism. We do not observe differences in edentulism between sex or residence (p>0.05). From 2009 to 2019, country data reports the lowest rate of edentulism in adults over 20 y.o (0.32%; 95% CI 0.18%-0.48%) and the most affected population over 79 y.o. (7.29%; 95% CI 5.2%-9.30%). As it is a cumulative phenomenon, it is necessary to establish better surveillance, prevention, and treatment programs to improve the oral health of older thus reducing edentulism.

United Nations Framework Convention on Climate Change (UNFCCC) has recently established the Reducing Emissions from Deforestation and forest Degradation (REDD+) program that requires countries to report their carbon emissions and sink estimates through national greenhouse gas inventories (NGHGI). Thus, developing automatic systems capable of estimating the carbon absorbed by forests without in-situ observation becomes essential. To support this important need, in this work we introduce ReUse, a simple but effective deep-learning approach to estimate the carbon absorbed by forest areas based on remote sensing. The novelty of the proposed method is in the use of the public above-ground biomass (AGB) data from the European Space Agency's Climate Change Initiative Biomass project as ground truth to estimate the carbon sequestration capacity of any portion of land on Earth using Sentinel-2 images and a pixel-wise Regressive UNet. The approach has been compared to two literature proposals, using a private dataset and human-engineered features. The results show a greater generalization ability of the proposed approach, with a decrease in Mean Absolute Error and Root Mean Squared Error, respectively, of 16.9 and 14.3 in the area of Vietnam and 4.7 and 5.1 in the area of Myanmar over the runner-up. Finally, as a case study, we reported an analysis made for the Astroni area, a nature reserve located near the metropolitan area of Naples in southern Italy, struck by a large fire, producing predictions consistent with values found by experts in the field. These results further support the use of such an approach for the early detection of AGB variations, both in urban and rural areas.

Research indicates that painful experiences can significantly affect the fear of cancer recurrence among cancer survivors, which is a distressing concern that influences both physiological and psychological recovery. Yet, the role of potential factors and mechanisms in these relationships is not fully known. This cross-sectional study aimed to advance our comprehension of the associa-tions between total pain and the fear of recurrence in post-treatment cancer patients by examining two potential mediators: psychological flexibility and mentalization. Three hundred and thirty-five participants (aged 22 to 88, 49.1% female) who had finished their cancer treatment completed self-report assessments of total pain, fear of recurrence, psychological flexibility, and mentalization. The serial mediation analysis showed that all dimensions of total pain were positively related to the fear of recurrence indirectly through psychological flexibility and mentalization, in serial. Additionally, gender moderated these serial mediational effects. In line with the psychological flexibility model, personal capacities to face difficult internal/external problems and interpret one’s behaviour in motivational terms can counterbalance patients’ negative emotions and feelings related to the illness.

Monitoring and measuring magnesium (Mg) values are essential to prevent the development of numerous complications in perioperative medicine and critically ill patients. Although previous studies suggest that measuring free ionized magnesium (iMg) is more useful for estimating Mg status, clinicians currently rely on measurement of total serum magnesium to determine if supplemental magnesium is needed. In this review, we analyzed the recent literature to decide whether it is better to measure ionized serum Mg or total serum Mg when assessing magnesium status, whether iMg predicts clinical outcome, and what are the difficulties in measuring serum iMg levels in intensive care patients and perioperative medicine.

Assessing the economic supply of biomass in a geospatial context while accounting for risk from natural disasters was studied. Risk levels were estimated from a component of factors which included: population density, road density, federal ownership, U.S. Environmental Protection Agency ecoregions, and Presidential Disaster Declarations. The Presidential Disaster Declarations included risks due to: coastal storm, drought, fire, flood, freezing, hurricane, mud land slide, severe ices, severe storms, snow, tornado, and tropical storm. Presidential Disaster Declarations included summaries based on a short-term time period from 2000-2011, and on a long-term time period from 1964-2011. Risk categories were developed as a function of the number of disaster declarations, agricultural-to-forest land ratio, average road density, and average population density. A significant contribution of the research was the allocation of spatially explicit data using GIS technology at the 5-digit zip code tabulation area. The average area for 5-digit ZCTAs in the Eastern U.S. study region was approximately 169 kilometers². Long-term risk (1964-2011) from disaster declarations had a greater impact on the economic availability of biomass supply relative to short-term declarations (2000-2011). The greatest risk to biomass supply came from population density relative to the other risk factors studies. Of the 25,044 total ZCTAs, 12,256 ZCTAs were in locations that did not include population density ≥ 150/km², road density ≥ 14 km/km², federal ownership, and US Environmental Protection Agency Level III ecoregions. Of the remaining 12,256 ZCTAs, 26.8% were considered to be moderate-to-high risk based on short-term declarations (2000-2011) and 29.4% were considered to be moderate-to-high risk based on long-term declarations (1964-2011). Lower risk locations for procuring biomass supply for both short-term and long-term declarations, across all risk factors, were in southern Georgia, South Carolina, and Texas.

Microalgae have emerged as potential feed stock for third generation biofuel and other bioactive compounds. In the present investigation we have evaluated the two native strains of Oscillatoria (O. subbrevis MTC-20702 and O. sancta MTC-20703) isolated from two different fresh water biotopes of Meerut, U.P., India and were subjected for the characterization of generation time, biomass, bio-molecules including Chlorophyll-a, carotenoids, carbohydrate, lipids, phycobilins and proteins. Both strains of Oscillatoria were grown in batch culture till the initiation of declining phase and were harvested on every 10th day of incubation till the starting of declining phase. Result of the present investigation revealed that O. subbrevis MTC-20702 can be potentially exploited for the production of high algal biomass, feed stock for biofuel, Chl-a, carotenoids, c-Allophycocyanin and maximum yield of these bioactive compounds can be achieved on 20th day. However, O. santa could be very good source for c-Phyocyanin, c-Phycoerythrin, carbohydrate and protein and these also can be achieved highest on 20th day of incubation. In addition, as these two strains were isolated from water reservoirs and they can be cultivated in large scale for the production of desired bio-molecules.

The emergence of cloud computing, big data analytics, and machine learning has catalysed the use of remote sensing technologies to enable more timely land management of sustainability indicators such as ground cover and grassland biomass, given the uncertainty of future climate and drought conditions. Here, we examine the potential of “regenerative agriculture”, as an adaptive grazing management strategy to minimise bare ground exposure while maximising pasture biomass productivity. High-intensity sheep grazing treatments were conducted in small fields (less than 1 hectare) for short durations (typically less than 1 day). Paddocks were subsequently spelled to allow pasture biomass recovery (treatments comprising 3, 6, 9, 12, and 15 months) with each compared with control treatments with lighter stocking rates for longer periods (2,000 DSE). Pastures were composed of wallaby grass (Austrodanthonia species), kangaroo grass (Themeda triandra), Phalaris (Phalaris aquatica, and cocksfoot (Dactylis glomerata) were destructively sampled to estimate total standing dry matter (TSDM), standing green biomass, standing dry biomass and trampled biomass. We then invoked a machine learning model using Sentinel-2 imagery to quantify TSDM, standing green biomass and standing dry biomass. Faced with La Nina conditions, regenerative grazing did not significantly impact pasture productivity, with all treatments showing similar TSDM and green biomass. However, regenerative treatments significantly impacted litter fall and trampled material, with the high intensity grazing treatments causing more dry matter trampling, increasing litter, enhancing decomposition rates and surface organic matter. Pasture digestibility was greatest for treatments with minimal spelling (3 months), whereas both standing senescent and trampled material were significantly greater for the treatment with 15-month spell periods. Estimates of TSDM using machine learning with Sentinel-2 imagery underestimated TSDM in treatment plots but explained spatiotemporal variability associated within and across treatments. The root mean square error between the measured and modelled TSDM was 903 kg DM/ha, which was less than the variability measured in the field. We conclude that regenerative grazing with short recovery periods (3-6 months) are most conducive to increasing pasture production under high rainfall conditions, and we speculate that high intensity grazing is likely to positively impact on soil organic carbon through increased litterfall and trampling. Our study paves the way forward for using machine learning with satellite imagery to quantify pasture biomass at small scales, enabling management of pastures from afar.

Pyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article focuses mostly on recent achievements in the technical and processing aspects of pyrolysis. This review provides an overview of the recent advanced pyrolysis technology used in gas, bio-oil, and biochar production. The key parameters to maximize the production of specific chemical compounds were discussed and considered during the construction of the reactors. The emphasis is put on optimizing the process parameters, technical requirements, and renewable energy use in the process and conception to improve the efficiency of product production. The application of pyrolysis gas, oil, and biochar as valuable chemical compounds are related to the intensifying effects of climate change, biofuel production, and waste management in accordance with the principles of sustainable development.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

Objective: Lipids are secreted into milk as bilayer-coated structures: milk lipid globules (MLGs). Adipophilin (ADRP) and perilipin 3 (TIP47) are associated with MLGs in human breast milk; however, the role of these proteins in milk lipid secretion is not fully understood. The aim of the study was to investigate levels of ADRP, TIP47 and total lipid content in human breast milk, their mutual correlations and dynamics during lactation. Research Methods & Procedures: Milk samples from 22 healthy lactating women (Caucasian, Central European) were collected at five time points during lactation (1–3, 12–14, 29–30, 88–90 and 178–180 days postpartum). Mass spectrometry-based method was used for quantification of ADRP and TIP47 in the samples. The gravimetric method was used to determine milk total lipid content. Results: We observed distinctive trends in ADRP, TIP47 levels and lipid content in human breast milk during the first 6 months of lactation. We also found a significant association between lipid content and ADRP, lipid content and TIP47, and ADRP and TIP47 concentrations in breast milk at all sampling points. Moreover, we derived an equation for estimating the mean lipid content of milk based on ADRP concentration in human breast milk. Conclusions: A mass spectrometry-based method was developed for quantifying ADRP and TIP47 in human breast milk. Strong mutual correlations were found between ADRP, TIP47 and total lipid content in human breast milk.

This study aims to analyze various types of pellet fuels used as energy sources in Bulgaria, focusing on their energy characteristics and the consumer preferences. Both standard and specialized methods such as thermogravimetry (TG) and differential scanning calorimetry (DSC) are used for the analyses. The results from TG and DSC indicate that during the drying of the samples, moisture is evaporated from their surface, along with the release of volatile substances. The processes during the analysis are accompanied by energy absorption, with the main stage being combustion, where the primary amount of heat is generated. Standard analysis methods show that wood pellets usually contain about 7.31% moisture, 0.72% ash and have a calorific value of 18.33 kJ/kg, while sunflower pellets contain about 7.62% moisture, 2.42% ash and have a calorific value of 19.63 kJ/kg. Mixed pellets contain about 7.07% moisture, up to 0.69% ash and have a calorific value of 18.05 kJ/kg. A specialized marketing research was conducted to investigate consumer attitudes and preferences toward purchasing different types of solid biomass fuels on Bulgarian market. This study provides information on the quality of pellets as fuel by offering a detailed analysis of their fuel properties and ensuring their effective utilization as an energy source.

Chlorella vulgaris has considerable promise as a raw material for biofuel production since it has a high productivity per unit area, has a minimum influence on the environment, and does not significantly affect food security. Nevertheless, the low fatty content of their biomass poses a considerable economic obstacle for commercialization. Increasing the amount of biomass and lipids produced by these algae is essential for improving the economic feasibility of using them as biofuel sources. This review highlights the significance of identifying appropriate algal strains, namely those found in local environments, and utilising mutagenesis and genetic engineering techniques to create 'platform strains'. Prior endeavours have primarily concentrated on altering environmental and dietary parameters to enhance the production of biomass and lipids. Here, we review a scientific literature that examines biotechnological approaches and develops methodologies designed to increase lipid production, emphasising the importance of aligning engineering efforts with breakthroughs in DNA manipulation tools. In addition, the review research evaluates the present economic and commercial situation of algal biorefineries, including any related disadvantages. In summary, this thorough research highlights the importance of using creative methods to tackle the intricacies of lipogenesis and enhance the economic viability of producing biofuels from algae.

In terms of sustainability, there is a pressing need to evaluate agricultural and forestry leafy biomass that has no current economic value or may pose a threat to the environment. In this aspect, leafy biomass, which represents around 5% of the total tree, can be used for purposes that would be more profitable and ecofriendly. To this end, biorefinery of leafy biomass in the way of extracting valuable health compounds such as phenolics would ensure a valuable societal health ingredient besides alleviating waste disposal problem. However, during the biorefinery process, the primary challenges start with ensuring the feedstock to produce phenol rich leaves extract followed by their isolation and commercialization of this leaves extract. This current review aims to detail the types of biomasses, biorefinery approach of leafy biomass towards the phenolic extraction, leaves commercialization followed by the marketing strategy of the application of phenol rich leaves extract. The outcome of this overview will serve researchers and relevant industries in understanding the process for feedstock collection and the suitable sectors to apply leafy biomass derived healthy compounds.

Pyrolysis is a thermochemical conversion process designed for biomass decomposition in an oxygen-free environment. It typically operates within a temperature window of 200 to 800°C and generates various byproducts, including gases, liquid fractions (both aqueous and organic) such as bio-oil, and solids like char. Bio-oil is a significant product of pyrolysis. It is characterised by a complex blend of organic compounds. The acidic nature of bio-oil primarily originates from volatile acids, such as acetic acid. The recovery of acetic acid from bio-oil facilitates the use of the extracted substance as a precious resource, hence enhancing its significance in the framework of a circular bioeconomy. Acetic acid finds widespread application in manufacturing commercially important chemicals like vinyl acetate monomers and formulating phytosanitary products due to its inherent herbicidal and antifungal properties. However, to be used, acetic acid has to be separate from the raw bio-oil. Separation methodologies, including nanofiltration and reverse osmosis, demonstrate potential in recovering acidic constituents from bio-oil due to their high selectivity and effective system management. This article offers a concise review about acetic production from lignocellulosic biomass from pyrolysis and its recovery through various membrane separation processes.

The exploitation of bio-based foams implies an increase in the use of renewable biological resources to reduce the rapid consumption of petroleum-derived resources. Both tannins and furfuryl alcohol are derived from forestry resources and are therefore considered as attractive precursors for the preparation of tannin-furanic foams. In addition, toughening modification of tannin-furanic foams using polyvinyl alcohol (PVOH) resulted in a more flexible network-like structure, which imparts excellent flexibility to the foams with acquirement of relative properties that are even close to those of polyurethane foams, which are the most used polymers for fabrication of insoles for athletes. In addition, the addition of PVOH did not affect the thermal insulation of the foams, resilience and elongation at break, while reducing the brittleness of the samples and improving the mechanical properties. Also the observation of the morphology of the foam indicated that the compatibility between PVOH and tannin-furanic resin is good, and the cured foam does not show fragmentation or collapse, while the bubble pore structure is uniform. The developed flexible foam derived from biomass resources endowed the foam good thermal insulation properties and high mechanical properties, and the samples exhibited suitable physical parameters to be used as flexible insoles for athletes.

The aim of this research was to test recent developments in the use of Remotely Piloted Aircraft Systems or Unmanned Aerial Vehicles (UAV) to map pasture biomass yield and nutrient status, across a selected range of field sites throughout the rangelands of Queensland. Improved pasture management begins with an understanding of the state of the resource base, UAV based methods can potentially achieve this at improved spatial and temporal scales. This study developed predictive models of both pasture yield and pasture nutrient status. An automated pasture height surface modelling technique was developed, tested and used along with field site measurements of pasture yields, to predict further estimates across each field site. Both prior knowledge and automated predictive modelling techniques were employed to predict pasture yield and nutrition. Pasture height surface modelling was assessed against field measurements using a rising plate meter, results reported correlation coefficients (R2) ranging from 0.2 to 0.4 for both woodland and grassland field sites. Accuracy of the predictive modelling was determined from further field measurements of pasture yield and on average indicated an error of 0.8 t ha-1 in grasslands and 1.3 t ha-1 in mixed woodlands across both modelling approaches. Correlation analyses between measures of pasture quality, acid detergent fibre and crude protein (ADF, CP), and spectral reflectance data indicated the visible red (651 nm) and red-edge (759 nm) regions were highly correlated (ADF R2 = 0.9 and CP R2 = 0.5 mean values). These findings agreed with previous studies linking specific absorption features with grass chemical composition. These results conclude that the practical application of such techniques, to efficiently and accurately map pasture yield and quality, is possible at the field site scale, however further research is needed, in particular further field sampling of both yield and nutrient elements across such a diverse landscape, with the potential to scale up to a satellite platform for broader scale monitoring.

The present article discusses the institutional model adopted in Brazil regarding energy production through biomass. The theoretical-empirical method is used to conclude that the model's difficulties can be overcome by adopting a network of contracts capable of subjecting renewable energy generation to an energy compensation model.

The case for demand-driven research and development has received important considerations among governments, donors and programme implementing partners in development planning and implementation. Addressing demand is believed to be a bottom-top approach for designing and responding to development priorities and is good for achieving development outcomes. In this paper, we discuss the concept and application of demand driven research for development (DDRD) in Africa. We use evidence of six projects implemented under the BiomassWeb Project in Africa. We focus on parameters on level of engagement of stakeholders - whose demand is being articulated, the processes for demand articulation, capacity building and implementation processes, innovativeness of the project, reporting and sustainability of the project. We find that the nature of the institutions involved in articulation and implementation of demand-driven research and development projects and their partnerships influence the impact and reporting of demand-driven projects.

Nowadays, there is evidence that bacteria can contribute to cancer formation and interfere with therapy by mediating its carcinogenesis and related infection. Moreover, it is acknowledged that microbial infections and antibiotic resistance represent severe economic and health risks to society. These facts have led to the developing of several new techniques for impeding crucial biological processes in microbial cells. One of these techniques centers on using metal-chelating agents, which can disrupt the microorganism's vital metal metabolism by obstructing metal uptake and bioavailability for critical reactions. Additionally, nanotechnology has made a wide range of nanomaterials available for possible uses in the antibacterial industry. This complex field is shaped by antimicrobial nanoparticles, also investigated as therapeutic and drug-delivery tools. Halloysite nanotubes (HNTs) are naturally occurring tubular clay nanomaterials consisting of aluminosilicate kaolin sheets rolled up several times. The aluminon and siloxane groups on the surface of HNTs facilitate the formation of hydrogen bonds with biomaterials on their surface. These properties make HNTs crucial in a wide range of applications, such as in environmental sciences, wastewater treatment, dye removal, nanoelectronics and nanocomposite fabrication, catalytic studies, coatings for glass or anti-corrosive coatings, cosmetics, flame retardants, stimulus-response, and in forensic sciences. This work aimed to produce an antibacterial material by combining the properties of halloysite nanotubes with the ability of kojic acid to chelate iron. Starting from kojic acid, a simple nucleophilic substitution involving the hydroxyl groups on the surface of the nanotubes was performed. The obtained material was characterized by IR and SEM, and its ability to chelate iron was evaluated. Finally, the capacity to load drugs such as resveratrol and curcumin was also evaluated by UV analysis. In this way, a new bio-based material that can be used as a drug carrier and antimicrobial was produced.

Lake Malombe fish stocks have been depleted by chronic overfishing. Various management approaches (co-management, command control, and ecosystem-based management to fisheries) have been used to manage the fishery. However, the lack of an accurate predictive model has hampered their success. Therefore, we developed and tested a time series model for Lake Malombe fishery. The seasonal fish biomass and CPUE trends were first observed and both were non-stationary. The second-order differencing was applied to transform the non-stationary data into stationary. Autocorrelation functions (AC), partial autocorrelation function (PAC), and Akaike information criterion (AIC) were estimated, which led to the identification and construction of autoregressive integrated moving average (ARIMA) models, suitable in explaining the time series and forecasting. The results showed that ARIMA (1,2,1) provided a better prediction than its counterparts. The model satisfactorily predicted that by 2032, both fish biomass and CPUE will decrease to 3204.6 tons and 59.672 respectively, signifying the potential threat to Lake Malombe fishery. The model justified the necessity of taking precautionary measures to avoid the total collapse of the fishery.

Based on recent interest and on the importance of the ongoing climate change catastrophe, this article provides the basics of global carbon cycle modelling as required for the assessment of the degree of carbon neutrality of biomass energy, and its underlying dynamics. It is aimed at clari-fying the question “Are biomass fuels carbon neutral?”. The "Combined Energy and Biosphere Model" (CEBM) computes annual carbon flows including growth and decay of plants on 2.52.5° grid elements of the continents’ surface and offers detailed results on the changes of after implementation of large-scale biomass energy strategies world-wide. The main (and possibly unexpected) effect is the long-term depletion of the soil organic compartment after extraction of biomass fuels. When comparing CEBM model runs using (i) biomass energy sources and (ii) carbon-free energy sources (such as solar or wind), it becomes quantitatively clear already on the theoretical level (i.e., even without taking into account effi-ciency losses) that biomass is only “half as carbon neutral” as ideally assumed, to express a rule of thumb – mainly because of soil carbon depletion. Still, biomass energy will play an important role when fighting global warming, even if efforts to lower energy demand are preferable as a fundamental strategy.

Biomass gasification acquired great interest over the past decades as an effective and trustable technology to produce energy and fuels with net-zero carbon emissions. Moreover, using biomass waste as feedstock enables to recycle organic wastes and to fit the circular economy goals thus reducing the environmental impacts of waste management. Even if many studies have been already carried on, this kind of process must still be investigated and optimized with the final aim to develop industrial plants for different applications, from the hydrogen production to net-negative emission strategies. Modeling and developing of process simulations became an important tool to investigate the chemical and physical behavior of the plant, allowing to make a first raw optimization of the process and to define heat and material balances of the plant as well as to define optimal geometrical parameters with cost and time effective approaches. The present review paper focuses on the main literature models developed until now to describe biomass gasification process, and in particular on kinetic models, thermodynamic models, and computational fluid dynamic models. The aim of this study is to point out the strengths and the weakness of those models, comparing them and indicating in which situation is better to use an approach instead of another. Moreover, theoretical shortcut models and software simulations, not explicitly addressed by prior reviews, are taken into account. For researchers and designers this review provides a detailed methodology characterization as a guide to develop innovative study or project.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

Chaparral shrublands are the dominant wildland vegetation type in southern California and the most extensive ecosystem in the state. Disturbance by wildfire and climate change have created a dynamic landscape in which biomass mapping is key in tracking the ability of chaparral shrub-lands to sequester carbon. Despite this importance, most national and regional scale estimates do not account for shrubland biomass. Employing plot data from several sources, we built a random forest model to predict above ground live biomass in southern California using remote sensing data (Landsat NDVI) and a suite of geophysical variables. By substituting the NDVI and precipi-tation predictors for any given year we were able to apply the model to each year from 2000-2019. Using a total of 980 field plots, our model had a k-fold cross validation R2 of 0.51 and a RMSE of 3.9. Validation by vegetation type ranged from R2 = 0.17 (RMSE=9.7) for Sierran mixed conifer to R2 = 0.91 (RMSE = 2.3) for sagebrush. Our estimates showed an improvement in accuracy over a two other biomass estimates that included shrublands, with an R2 = 0.82 (RMSE = 4.7) compared to R2 = 0.068 (RMSE = 6.7) for a global biomass estimate and R2 = 0.29 (RMSE = 5.9) for a regional biomass estimate. Given the importance of accurate biomass estimates for resource managers we calculated the mean year 2010 shrubland biomass for the four national forests which ranged from 3.5 kg/m2 (Los Padres) to 2.3 kg/m2 (Angeles and Cleveland). Finally, we compared our estimates to field-measured biomass from the literature summarized by shrubland vegetation type and age class. Our model provides a transparent and repeatable method to generate biomass measure-ments in any year, thereby providing data to track biomass recovery after management actions or disturbances such as fire.

Many corporations aspire to become Net Zero Carbon Dioxide by 2030-2050. This paper examines what it will take. It requires understanding where energy is produced and consumed, the magnitude of CO2 generation, and the Carbon Cycle. Reviews are provided for prior technologies for reducing CO2 emissions from fossil to focus on their limitations and to show that none offer a complete solution. Both biofuels and CO2 sequestration reduce future CO2 emissions from fossil fuels. They will not remove CO2 already in the atmosphere. Planting trees has been proposed as one solution. Trees are a temporary solution. When they die, they decompose and release their carbon as CO2 to the atmosphere. The only way to permanently remove CO2 already in the atmosphere is to break the Carbon Cycle by growing biomass from atmospheric CO2 and sequestering biomass carbon. Permanent sequestration of leaves is proposed as a solution. Leaves have a short Carbon Cycle time constant. They renew and decompose every year. Theoretically, sequestrating a fraction of the world’s tree leaves can get the world to Net Zero without disturbing the underlying forests. This would be CO2 capture in its simplest and most natural form. Permanent sequestration may be achieved by redesigning landfills to discourage decomposition. In traditional landfills, waste undergoes several stages of decomposition, including rapid initial aerobic decomposition to CO2, followed by slow anaerobic decomposition to methane and CO2. The latter can take hundreds to thousands of years. Understanding landfill chemistry provides clues to disrupting decomposition at each phase.

This study compares the physico-chemical characteristics of three different types of biochar produced from biomass residues in Vietnam as a basis for optimising their application in water purification and soil fertilisation. Wood biochar (WBC), rice husk biochar (RBC), and bamboo biochar (BBC) were produced under limited oxygen conditions using equipment available locally in Vietnam, known as a Top-Lid Updraft Drum (TLUD). The resulting biochars were characterised using a suite of state-of-the-art methods to understand their morphology, surface chemistry and cation exchange capacity. Surface areas (measured by BET) for WBC and BBC were 479.34 m²/g and 434.53 m²/g, respectively, significantly higher than that of RBC which was only 3.29 m²/g. The morphology as shown in SEM images corresponds with the BET surface area, showing a smooth surface for RBC, a hollow surface for BBC, and a rough surface for WBC. All three biochars produced alkaline, with pH values around 10, and all have high carbon contents (47.95 - 82.1 %). Cation exchange capacity (CEC) was significantly different (p<0.05) among the biochars, being 26.70 cmol/kg for RBC, 20.7 cmol/kg for BBC, and 13.53 cmol/kg for WBC, which relates to the cations (Ca, Mg, K) and functional groups with negative charge (carboxyl, hydroxyl) present on the biochar surfaces. The highest contents of Ca, Mg and K in rice husk BC may explain its highest CEC values. Thus, although the biochars were produced by the same method, the various feedstocks lead to quite different physico-chemical properties. Ongoing work is linking these physico-chemical properties to the biochar efficiencies in terms of nitrate and ammonia capture capacities for use as fertilisers, and for adsorption of heavy metals (Zn, Cu) or water filtration, in order to design optimal biochar properties for specific applications.

Background: A careful work-up before Transcatheter aortic valve replacement (TAVR) consists not only of measuring anatomical conditions but also assessment of frailty. Previous studies have evaluated body composition parameters, primarily fat and muscle mass. Few data are available on other frailty parameters, which, however, can be easily determined by pre-TAVR computed tomography (CT). Objectives: The primary objective was to investigate the impact of total muscle area (TMA) and visceral adipose tissue (VAT), as frailty parameters, on 5-year all-cause mortality in patients undergoing TAVR. Methods: Between 01/2017 and 12/2018, consecutive TAVR patients undergoing CT-angiography scan enabling TMA and VAT measurement were included. A single axial image was acquired at the level of the middle third lumbar vertebra to perform TMA and VAT measurements using dedicated slicing software (Sliceomatic, TomoVision). Results: A total of 500 patients qualified for TMA analysis. Age was not associated with a higher risk of 5-year mortality HR 1.02 (95% CI: 0.998 - 1.049; p=0.069). Body surface area normalized TMA (nTMA) was significantly associated with 5-year all-cause mortality (HR 0.927, 95% CI: 0.927-0.997; p= 0.033), while VAT had no effect (HR 1.002, 95% CI: 0.99-1.015; p= 0.7). The effect of nTMA on 5- year all-cause mortality was gender-dependent: the protective effect of higher nTMA was found in male patients (pinteraction: sex * nTMA = 0.007). The combination of normalized TMA and VAT was not associated with higher mortality rates. Conclusion: Normalized TMA derived from routine CT before TAVR complements frailty assessment in patients undergoing TAVR.

The paper proposes a game theory model of price oligopoly with a heterogeneous product, where total demand depends linearly on the minimum market price. This model develops the Bertrand oligopoly for the case of imperfect price elasticity of demand. The most interesting result is an asymmetric Nash equilibrium with different prices and sales in the situation of symmetric oligopolists. The asymmetry is explained by the fact that a decrease in the minimum market price leads not only to a reallocation of consumers among firms, but also to an increase in total demand. Modifications of a two-stage game with a leader and followers and the price discrimination model are also considered. Microeconomic substantiation of the model is given on the basis of the spatial differentiation approach.

There are several causes of hypoxia during and after surgery, and atelectasis is a common symptom that occurs during surgery. In particular, elderly patients are more vulnerable to hypoxia due to their existing lung diseases or respiratory muscle weakness. This study presents the cases of two elderly patients who developed hypoxia during total hip arthroplasty under general anesthesia. Positive end expiratory pressure, recruitment maneuver, and increased fraction of inspired oxygen improved hypoxia only temporarily, and patients’ oxygen saturation level again dropped to 79%–80%. We suspected that hypoxia was caused by atelectasis and, therefore, re-sumed spontaneous respiration. Thereafter, both the patients showed an improvement in hypoxia. Intraopera-tive hypoxia that is suspected to be caused by atelectasis can be improved by securing sufficient lung volume for respiration through increased muscle tone with spontaneous respiration

Mercury is a neurotoxin, with certain organic forms of the element being particularly harmful to humans. The Minamata Convention was adopted to reduce the intentional use and emission of mercury. Because mercury is an element, it cannot be decomposed. Mercury-containing products and mercury used for various processes will eventually enter the waste stream, and landfill sites will become a mercury sink. While landfill sites can be a source of mercury pollution, the behavior of mercury in solid waste within a landfill site is still not fully understood. The purpose of this study was to determine the depth profile of mercury, the levels of methyl mercury (MeHg), and the factors controlling methylation in an old landfill site that received waste for over 30 years. Three sampling cores were selected, and boring sampling was conducted to a maximum depth of 18 m, which reached the bottom layer of the landfill. Total mercury (THg) and MeHg were measured in the samples to determine the characteristics of mercury at different depths. Bacterial species were identified by 16S rRNA amplification and sequencing, because the methylation process is promoted by a series of genes. It was found that the THg concentration was 19–975 ng/g, with a geometric mean of 298 ng/g, which was slightly less than the 400 ng/g concentration recorded 30 years previously. In some samples, MeHg accounted for up to 15–20% of THg, which is far greater than the general level in soils and sediments, although the source of MeHg was unclear. The genetic data indicated that hgcA was present mostly in the upper and lower layers of the three cores, merA was almost as much as hgcA, while the level of merB was hundreds of times less than those of the other two genes. A significant correlation was found between THg and MeHg as well as between MeHg and MeHg/THg. In addition a negative correlation was found between THg and merA. The coexistence of the three genes indicated that both methylation and demethylation processes could occur, but the lack of merB was a barrier for demethylation.

Distinguishable annual growth rings produce in Pinus roxburghii are an asset to find out the age of individual tree. This paper aimed to determine the age of P. roxburghii through coring samples and test the relationship with forest production. The biomass estimated, girths measured at two different sections and heights measured which allowed to determine the rate of tapering of the stand. The regression analysis was performed to test the relationship between various variables. The mean age of the P. roxburghii stand was found to be 23.97 (~24 years). The result showed the significant (p<0.05) positive correlation coefficient has been seen between age with girth at breast height, biomass, volume and carbon stock. However, no significant (p>0.05) correlation (r = 0.08) was found between age and height of the stand. In contrast, a correlation between diameter at breast height (DBH) was significant (p<0.05) and positive with volume, biomass, but no significant (p>0.05) correlation (r = 0.14) found between DBH and height of the stand. However, height has a significant (p<0.05) positive correlation with biomass. The mean biomass was 375 kg and mean annual increment (MAI) was 15 kg per tree. Rate of tapering of the studied stand predicted to be 3 cm diameter decreased with trunk height running at 100 cm from base to upward of P. roxburghii stand and vice versa. Result suggests that height-age relation is very weak whereas age, DBH, biomass and carbon has a significant correlation signifies that time-based forests' production and potential production estimation can be obtained in a relatively accurate way by utilizing the age of stand. The time-based forest production analysis is pioneer work in Nepal. The study affirms the tree ring count in P. roxburghii would be a credible and accurate method to determine the age of standing trees.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T1 = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T2 = 50 kg N ha^-1, T3 = 100 kg N ha^-1 and T4 = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T5: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T6: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T7: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO2 concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T6 = Split N100) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

Pathologies of the blood brain barrier (BBB) have been linked to a multitude of CNS disorders whose pathology is poorly understood. Cortical spreading depression (CSD) has long been postulated to be involved in the underlying mechanisms of these disease states, yet full understanding remains elusive. This study utilized an in vitro model of the BBB with b.End3 murine endothelial cells to investigate the role of CSD in BBB pathology by characterizing effects of the release of major pronociceptive substances on BBB functional integrity using TEER screening, transcellular uptake, and immunoreactive methods in concert with global proteome and phospho-proteomic approaches. Findings demonstrated relocalization and functional alteration to proteins associated with the cytoskeleton and endothelial tight junctions. Pathologic mechanisms induced by individual substances released during CSD were found to have unique phosphorylation signatures in phospho-proteome analysis, identifying Zona Occludens 1 as a possible pathologic “checkpoint” of the BBB. Utilizing these phosphorylation signatures, possible novel diagnostic methods may be developed for neurological diseases and warrants further investigation.

Biogeochemical models estimate soil organic carbon (SOC) sequestration, crop growth, and yield. The DeNitrification and DeComposition (DNDC) model was used to simulate soil SOC dynamics and harvested C-biomass in rice-wheat rotation under organic/inorganic fertilizations with conventional tillage (CT) and reduced tillage (RT). Before calibration, DNDC under-predicted harvestable grain C-biomass of rice by 29.22% to 42.14% and over-simulated grain C-biomass of wheat by 55.01% with equal amounts of NPK and animal manure applied under CT. However, after calibration by adjusting default values of soil/crop parameters, DNDC simulated harvestable grain C-biomass of both crops very close to observed values (only -2.81% to -6.17% less). DNDC also predicted effects of nutrient management practices on grain C-biomass of rice/wheat under CT/RT using d-index (0.76 to 0.96) and the calculated root mean squared error (RMSE of 165.36 to 494.18 kg C ha-1). DNDC simulated SOC trends for rice-wheat using measured values of several statistical indices. Regression analysis between modeled and observed SOC dynamics was significant with R2 ranging from 0.35 to 0.46 (p < 0.01), and intercept ranging from 0.30 to 1.34 (p < 0.65). DNDC demonstrated that combined inorganic and organic fertilization may result in higher C-biomass and more SOC sequestration in rice-wheat systems.

The total ionizing dose (TID) effect significantly impacts the electrical parameters of fully depleted silicon on insulator (FDSOI) devices and even invalidates the on-off function of devices. At present, most of the irradiation research on the circuit level is focused on the single event effect, and the research on the total ionizing dose effect is very little. Therefore, this study mainly analyzes the influence of TID effects on a CMOS inverter circuit based on 22 nm FDSOI transistors. First, we constructed and calibrated an N-type FDSOI metal-oxide semiconductor (NMOS) structure and P-type FDSOI metal-oxide semiconductor (PMOS) structure. The transfer characteristics and trapped charge distribution of these devices were studied under different irradiation doses. Next, we studied the TID effect on an inverter circuit composed of these two MOS transistors. The simulation results show that when the radiation dose is 400 krad (Si), the logic threshold drift of the inverter is approximately 0.052 V. These results help further investigate the impact on integrated circuits in the irradiation environment.

Objective: To determine the effect of birth season climate on adult total serum IgE (TSIgE) levels. Study design: The study is a retrospective chart review with the following inclusion criteria: TSIgE measurement, age ≥16, and northeastern Tennessee birthplace. Main outcome measures include TSIgE levels, birth season climatic conditions, and regional pollen-producing plant and pollen counts. Results: The records of 1,274 women (mean age 40.8 ± 17.5, age range 16-96) and 762 men (mean age 38.1 ± 17, age range 16-82) seen in our Allergy Clinic were reviewed. Persons born in the spring and summer, the seasons with the highest pollen counts and the most favorable climatic conditions for plant growth, had nearly twice the odds of having TSIgE levels >1σ above the mean of the study group when compared to those born in the fall or winter (odds ratio (OR) 1.75, 95% confidence interval (CI) 0.96-3.17 and OR 1.93, 95% CI 1.04-3.57, respectively); odds were highest for those born in March (OR 2.55, 95% CI 1.37-4.74) and July (OR 2.38, 95% CI 1.25-4.51) and lowest for those born in November (OR 0.11, 95% CI 0.0068-1.79). When averaged over the 95-years of study and five 30-year climate cycles TSIgE levels increased linearly as the seasons progressed from fall to summer (r²= 0.9475, P=0.0266). Of the climatic factors, TSIgE levels correlated most strongly with levels of precipitation (r²= 0.9145, P=0.0437). Conclusion: Climatic conditions that increase birth season exposure to environmental allergens may have a life-long effect on TSIgE production.

The purpose of this work is to study Rossby wave parameters in total ozone over Arctic in 2000–2021. We consider the averages in the January–March period, when stratospheric trace gases (including ozone) in sudden stratospheric warming events are strongly disturbed by planetary waves. To characterize the wave parameters, we analyzed ozone data at the latitudes of 50° N (the sub-vortex area), 60° N (the polar vortex edge) and 70° N (inner region of the polar vortex). Total ozone column (TOC) measurements during 22-year time interval were used from Total Ozone Mapping Spectrometer (TOMS) / Earth Probe and Ozone Mapping Instrument (OMI) / Aura satellite observations. The total ozone zonal distribution and variations in the parameters of the Fourier spectral components with zonal wave numbers m = 1–5 are presented. Daily and interannual variations in TOC, amplitudes and phases of spectral wave components, and linear trends of the quasi-stationary wave 1 (QSW1) amplitudes are discussed. The positive TOC peaks inside the vortex in 2010 and 2018 alternate with negative ones in 2011 and 2020. The latter TOC anomalies correspond to severe depletion of stratospheric ozone over the Arctic in the strong vortex conditions due to anomalously low activity of planetary waves. Variations in TOC in sub-vortex region exhibit the statistically significant negative trend –4.8±5.4 DU decade–1 in QSW1 amplitude, while the trend is statistically insignificant at the vortex edge region due to increased TOC variability. Processes associated with polar vortex dynamics are discussed, including quasi-stationary vortex asymmetry and quasi-circumpolar migration of the wave-1 phase at the vortex edge.

According to the IPCC guidelines, CO₂ emissions from biomass should be excluded from the entire amount of CO₂ emissions when calculating CO₂ emissions and should be separately reported due to the “carbon neutrality.” Sewage sludge is one of the representative biomass fuels. And it is mixed with fossil fuels in terms of greenhouse gas reduction or is used as fuel to replace fossil fuels by itself. According to the results of this study, biomass contents of both the sewage sludge and the sewage sludge incineration exhaust gases did not amount to 100%. At present, in many countries(South Korea, Japan, and Germany), when calculating greenhouse gas emissions from sewage sludge incinerator, all CO₂ emissions from sewage sludge are judged to be biomass and only those greenhouse gas emissions that correspond to Non-CO₂ gases are calculated as greenhouse gas emissions. However, since, according our results, the content of sewage sludge is not 100% biomass, if CO₂ emissions are excluded according to the existing greenhouse gas emission calculation method, the amount of emissions may be underestimated. Therefore, to accurately calculate greenhouse gas emissions from sewage sludge incinerator, CO₂ emissions should be calculated in consideration of the fossil carbon contents of sewage sludge.

In recent years, the treatment of locally-advanced rectal cancer (LARC) has been spotlighted in a number of landmark, practice-changing trials, heralding in the age of so-termed “total neoadjuvant therapy” (TNT). However, the lack of a common control arm, standard inclusion criteria, or, indeed, definition of TNT necessitates further study in this field, particularly using real-world data. We conducted a retrospective analysis of all patients treated for LARC at a single Canadian academic cancer centre between July 1st 2019 and July 14th 2022. This includes the June 2020 incorporation of TNT. 290 patients were included in the final analysis, and 124 variables were collected on each patient, including demographics, treatment type, adverse events, response to treatment, surgery versus watchful waiting and survival. Our findings demonstrate that both TNT and non-TNT regimens are highly toxic, with regards to both overall toxicity and grade 2+ adverse effects. 62 (96.9%) of patients on TNT experienced toxicities, compared to 186 (82.3%) of the non-TNT patients. Grade 2+ toxicities were 46 (71.9%) and 143 (63.3%), respectively. TNT, however, was associated with improved rates of complete response, compared to non-TNT treatment regimens (44% vs 24%). These findings suggest that TNT harbours both benefit and risk in a real-world population, and both of these aspects should be considered when deciding on a treatment approach for an individual patient. More work in the area is needed to determine longer term survival, as well as impact of surgery versus organ preservation approach on patient outcomes.