A U.S. government health agency conducted epidemiological studies to evaluate whether exposures to drinking water contaminated with volatile organic compounds at U.S. Marine Corps Base Camp Lejeune, North Carolina, were associated with increased health risks to children and adults. These health studies required knowledge of contaminant concentrations in drinking water—at monthly intervals—delivered to family housing, barracks, and other facilities within the study area. Because concentration data were limited or unavailable during much of the period of contamination (1950s–1985), the historical reconstruction process was used to quantify estimates of monthly mean contaminant-specific concentrations. This paper integrates many efforts, reports, and papers into a synthesis of the overall approach to, and results from, a drinking-water historical reconstruction study. Results show that at the Tarawa Terrace water treatment plant (WTP) reconstructed (simulated) tetrachloroethylene (PCE) concentrations reached a maximum monthly average value of 183 micrograms per liter (ug/L) compared to a one-time maximum measured value of 215 ug/L and exceeded the U.S. Environmental Protection Agency’s current maximum contaminant level (MCL) of 5 ug/L during the period November 1957–February 1987. At the Hadnot Point WTP, reconstructed trichloroethylene (TCE) concentrations reached a maximum monthly average value of 783 ug/L compared to a one-time maximum measured value of 1,400 ug/L during the period August 1953–December 1984. The Hadnot Point WTP also provided contaminated drinking water to the Holcomb Boulevard housing area continuously prior to June 1972, when the Holcomb Boulevard WTP came on line (maximum reconstructed TCE concentration of 32 ug/L) and intermittently during the period June 1972–February 1985 (maximum reconstructed TCE concentration of 66 ug/L). Applying the historical reconstruction process to quantify contaminant-specific monthly drinking-water concentrations is advantageous for epidemiological studies when compared to using the classical exposed versus unexposed approach.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

This paper describes the development of a two-dimensional water quality model that solves hydrodynamic equations tied to transport equations with reactions mechanisms inherent in the processes. This enable us to perform an accurate assessment of the pollution in a coastal ecosystem. The model was developed with data drawn from the ecosystem found in Mexico's southeast state of Tabasco. The coastal ecosystem consists of the interaction of El Yucateco lagoon with the Chicozapote and Tonalá rivers, that connect the lagoon with the Gulf of Mexico. We present the results of pollutants transport simulation in the coastal ecosystem, focusing on toxic parameters for two hydrodynamic scenarios: wet and dry seasons. As it of interest in the zone, we study the transport of four metals: Cadmium, Chromium, Nickel and Lead. In order to address our objectives we solved numerically a self-posed mathematical problem,which is based on the measured data. The performed simulations show to characterise metal transport within the acceptable range of accuracy and in accordance with the measured data. The performed simulations show to characterise metals transport with an acceptable accuracy, agreeing well with measured data in total concentrations in four control points along the water body. Although for the accurate implementation of the hydrodynamic-based water quality model herein presented, boundary (geometry, tides, wind, etc.) and initial (concentrations measurements) conditions are required, it poses as an excellent option when the distribution of solutes with high accuracy is required, easing environmental, economic and social management of coastal ecosystems.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

Infant foods and formulae may contain toxic substances and elements which can be neo-formed contaminants or derived from raw materials or processing. The content of minerals, toxic elements and hydroxymethylfurfural in infant foods and formulae were evaluated. The effect of storage temperature on HMF formation in infant formulae and its potential as a quality parameter was also evaluated. Prune-based foods contained the highest HMF content. HMF significantly increased when storage temperature was elevated to 30 ℃ for 21 days. All trace elements were present in adequate amounts while the concentration of nickel was higher when compared to those of other studies. The study indicates that HMF can be used as quality indicator for product shelf-life and that the concentrations of minerals and toxic elements vary greatly due to the diverse compositions of foods and formulae. Such contaminants need to be monitored as infants represent a vulnerable group compared to adults.

Cereals and their derivatives are the basis of human nutrition. However, cereals also contribute to the dietary exposure to toxic metals that may pose a risk. Strengthening food security and nutrition information is a high priority challenge for the Cape Verde Government. The toxic metals content (Cr, Ni, Sr, Al, Cd, Pb) has been determined in 126 samples of cereals and derivatives (rice, corn gofio, corn flour, wheat flour, corn, wheat) consumed in Cape Verde. Wheat flour samples stand out for registering the highest Sr (1.60 mg/kg), Ni (0.25 mg/kg) and Cr (0.13 mg/kg). The results show relevant Al levels (1.17 – 13.4 mg/kg) with its highest levels in corn gofio. The mean Pb average content in the cereals is 0.03 – 0.08 mg/kg with the highest level observed in corn gofio. The Al and Pb levels are lower in cereals without husks. A consumption of 100 g/day of corn gofio provide an intake of 1.34 mg Al/day (13.7% of the tolerable weekly intake established at 1 mg/kg bw/week) and 8 µg Pb/day (20% of the BMDL set at 0.63 µg/kg bw/day for nephrotoxic effects). The minimization of the dietary exposure of the Cape Verdean population to toxic metals is through the importation of higher quality cereals.

Bonfire night is a worldwide phenomenon given to numerous annual celebrations characterised by bonfires and fireworks. Since Thailand has no national ambient air quality standards for metal particulates, it is important to investigate the impacts of particulate injections on elevations of air pollutants and ecological health impacts resulting from firework displays. In this investigation, Pb and Ba were considered potential firework tracers because their concentrations were significantly higher during the episode and lower than/comparable with minimum detection limits during other periods, indicating that their elevated concentrations were principally due to pyrotechnic displays. Pb/Ca, Pb/Al, Pb/Mg, and Pb/Cu can be used to pin-point emissions from firework displays. Air mass backward trajectories (72 h) from the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model indicated that areas east and north-east of the study site were the main sources for the air transportation. Although the combined risk associated with levels of Pb, Cr, Co, Ni, Zn, As, Cd, V, and Mn was far below the standards mentioned in international guidelines, the lifetime cancer risks associated with As and Cr levels exceeded US-EPA guidelines, and may expose inhabitants of surrounding areas of Bangkok to elevated cancer risk.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

Evidence has been accumulated demonstrating that heavy metals may accumulate in various organs leading to tissue damage and toxic effects in mammals. In particular, the Central Nervous System (CNS) seems to be particularly vulnerable to cumulative concentrations of heavy metals, though the pathophysiological mechanisms is still to be clarified. In particular the potential role of oligodendrocyte dysfunction and myelin production after exposure to subtoxic concentration of heavy metals is to be better assessed. Here we investigated on the effect of sub-toxic concentration of several essential (Cu^{2 +}, Cr³⁺, Ni²⁺, Co²⁺) and non-essential (Pb²⁺, Cd²⁺, Al³⁺) heavy metals on MO3.13 and SHSY5Y human oligodendrocyte and neuronal cell lines (grown individually or in co-culture). In particular, exposure of both cell lines to heavy metals produced a reduced cell viability of co-cultured cell lines compared to cells grown separately. This effect was more pronounced in neurons which were more sensitive to metals than oligodendrocytes when the cells were grown in co-culture. On the other hand, a significant reduction of lipid component in cells occurred after their exposure to heavy metals, an effect accompanied by substantial reduction of the main protein that makes up myelin (MBP) in co-cultured cells. Finally, the effect of heavy metals in oligodendrocytes were associated to imbalanced intracellular calcium ion concentration as measured through the fluorescent Rhod-2 probe, thus confirming that heavy metals, even used at subtoxic concentrations, lead to dysfunctional oligodendrocytes. In conclusion, our data show, for the first time, that sub-toxic concentrations of several heavy metals lead to dysfunctional oligodendrocytes, an effect highlighted when these cells are co-cultured with neurons. The pathophysiological mechanism(s) underlying this effect is to be better clarified. However, imbalanced intracellular calcium ion regulation, altered lipid formation and, finally, imbalanced myelin formation seem to play a major role in early stages of heavy metal-related oligodendrocyte dysfunction.

Among others, road traffic, industrial emissions, commercial activities, smoking and cooking are considered as major contributing factors for the increasing levels of pollutants in atmosphere. High levels of potentially toxic metals and microbes in atmosphere, especially in indoor air, may pose serious threat to human health. Therefore, concentration and associated health risks of potentially toxic trace metals (Cd, Cr, Cu, Fe, Mn, Pb, and Zn) and their risk to human health, and microbial load in indoor air was assessed using air condition (AC) filter dust samples collected from 5 locations representing residential, agricultural and industrial settings of Eastern Province, Kingdom of Saudi Arabia. The levels of trace metals varied considerably among sampling areas, with the highest levels of Cr and Cd recorded in the Industrial-area sites followed by the Agricultural and Urban-Residential sites. The highest levels of Pb and Fe were found in the Agricultural area sites followed by the Industrial and Urban-Residential area sites. The metals in dust sample, especially Cd, Cr and Pb, showed a considerable health risk through dermal pathway. Among the sites, the highest hazard quotient for these metals was found for Al-Qatif-Industrial areas sites and among the metals it was the highest for Cd. The cancer risk from the metals contained in AC filter dust was negligible. Samples collected from Agricultural and Industrial area sites were substantially contaminated with bacteria and fungi, respectively. Bacterial contaminants were mostly Gram Negative, with considerable antibiotic resistance and haemolytic activity. Thus, indoor air quality as assessed by AC filter dust depicted that a considerable health risk could be posed by the trace heavy metals and microorganisms for a long-term exposure. Furthermore, this study demonstrated that AC filters dust could be a unique and reliable test sample for the assessment of indoor environment.

Novel functionalized and/or grafted crosslinked chitosan adsorbents were synthesized and used to remove several toxic heavy metal ions from contaminated water efficiently and selectively. The chitosan biopolymer was functionalized by maleic anhydride (CS_MA), which also acted as a crosslinking agent. Separately, Glutaraldehyde-crosslinked chitosan (CS_GA) was grafted with poly(methyl methacrylate) (CS_MMA). The synthesized adsorbents were used to adsorb and remove heavy metal ions from contaminated water. The metal ions were nickel, lead, chromium, and cadmium. The adsorption capacity of the adsorbents was analyzed under various conditions of contact time, adsorbent dose, initial concertation, temperature, and pH and evaluated against those of pure chitosan (CS) and the crosslinked one (CS_GA). The ultimate conditions for the ions removal were 0.5g/100ml adsorbent dose, an initial metal ion concentration of 50 ppm, a temperature of 45oC, and a pH 9. CS_MMA, which had the highest removal percentages for all metal ions, ranging from 92% to 94%. The adsorption was demonstrated to fit a pseudo-first-order model that followed a Langmuir adsorption isotherm. The results highlight the capacity of the synthesized polymers to efficiently remove major toxic contaminants at low cost from contaminated water, present especially in low-income areas, without harming the environment.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

Natural radioactivity of 238U, 232Th and 40K for liquid and solid samples collected from Sidi Salem dam (Tunisia) and Aïn Dalia dam (Algeria) were measured using TERRA detector of rays (gam-ma, beta, and alpha), Atomic adsorption and Gamma-ray spectrometry were used to analyze the levels of radionuclides and toxic heavy metals, respectively. Toxic heavy metals (Fe, Bb, Zn, Ni, Cu, Cr and Cd) and associated health risks in surface water and sediment of dams have been in-vestigated in this present study. The radioactivity mean rates in the water samples were 1.72±0.01, 0.068±0.01 and 94.6±1.04 Bql-1 for 238U, 232Th and 40K respectively (Tunisia dam) and were 1.9± 0.24, 0.09±0.01 and 131.43±1.03 Bql-1 for 238U, 232Th and 40K respectively (Algeria dam). The 238U, 232Th and 40K radioactivity mean concentration measured in the sediment samples were 2.67±0.01, 0.18±0.012 and 197.87±2.01 Bqkg-1 respectively (Tunisian dam) and were 4.34±0.05, 0.27±0.05 and 287.61±3.34 Bqkg-1 respectively (Algeria dam). The activity concentration of 40K was higher than that of 238U and 232Th for the water and sediment samples. The mean activity concen-trations follow the order 40K > 238U > 232Th. The cumulative impact can be a serious immediate radiological health burden on the ecosystem, environment and people's health in this study area and can be transposable to any other similar region. The good knowledge of monitoring quality and quantity for the transboundary water resources and the international collaborations are es-sential to safeguard human health (women’s breasts cancer, thyroid cancer, neurological im-pact…), and avoid the conflicts, especially during these climatic upheavals of drought.

Hazardous toxic metals, such as lead and cadmium, and to a lesser extent aluminum, are extensively recognized as detrimental for health following ingestion within food and water, or following inhalation. Gut and food-derived microbes, by interacting with heavy metals, may actively or passively modulate their bioavailability inside the gut, either by adsorption or by sequestration. Such a bioremediation within the gut implies the selection of safe microbes, based on their specific capacities to immobilize metals. We investigated the metal removal ability of 225 bacteria toward the potential harmful trace elements lead, cadmium and aluminum in vitro, using Inductively Coupled Plasma Mass Spectrometry analysis. Interspecies and intraspecies comparisons were addressed and discussed among bacteria from the phylum Firmicutes, which are mostly lactic acid bacteria, including Lactobacillus spp, with some Lactococcus, Pediococcus and Carnobacterium representatives, Actinobacteria as well as Proteobacteria. The effect on mixture of lead and cadmium was also investigated. Although the purpose of such a screening is so far not to elucidate each of the various strain specific- and metal dependent- mechanisms of heavy metal removal, we identified potential bacteria which are able to alleviate Pb(II) and Cd(II) concerns in order to propose performing candidate probiotics for metal xenobiotic bioremediation.

Metals are particularly sensitive to some pollutant gases. Many museum showcases and store rooms present atmospheres that can corrode cultural heritage artefacts containing metals. Whilst numerous strategies have been reported to mitigate such situations, avoiding them is preferable. Several approaches to testing materials used in construction, fitting out or dressing are used. The relative merits and drawbacks will be discussed. Several parameters of the most widely used, the accelerated corrosion ‘Oddy’ test have been investigated. The influence of abrasive on subsequent corrosion of lead and copper coupons have been assessed. Quantification methods for tested coupons are reviewed. The influence of test duration and temperature were assessed through comparison with real life, long term experience of materials behaviour. Direct contact tests with the material tested touching the test material has been investigated. Several materials present in artefacts are known to potentially cause corrosion when enclosed with metals in other artefacts. A number of situations have been investigated with pollution and RH and some corrosion rate measurements. Ways to isolate artefacts or mitigate are explored and a decision support model has been developed.

Heavy metal accumulation in soils used for agricultural purposes is a major issue as it can affect the growth of plants and contain health risks as plants containing heavy metals are taken as food. This study provided the potential of three Bacillus pumilus strains (C-2PMW-8, C-1 SSK-8, and C-1PWK-7) for mitigation of the health factors related to heavy metals on lettuce (Lactuca sativa) grown in chromium contaminated soil from activities related to mining. Lettuce seeds inoculated with B. pumilus strains were grown in pots with garden soil amended with varying amount of chromite mine soil (2.27%, 4.65%, 7.14%). Growth indicators like days to germination, percentage of germination, leaf weight, leaf area and rate of survival decreased with incremental soil chromium levels but improved highly with inoculation of B. pumilus compared to uninoculated controls. When B. pumilus strains were provided, there was also a decreased level in the buildup of chromium in soil as well as lettuce shoots. The results explains that plant growth-promoting B. pumilus strains may be able to lower down the detrimental effects of chromium on lettuce development, hence increment in the effectiveness of phytoremediation.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

The results of the investigation showed that second-order kinetics govern the adsorption process, and the corresponding rate constants were found. To evaluate the parameters related to the adsorption process, the adsorption equilibrium was examined using a variety of mathematical models, such as the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models. The Langmuir isotherm was found to be the best appropriate among all models for describing the adsorption of Cu2+ and Ni2+ ions using bio-nanocomposite beads. The positive values of ΔH° indicate that the adsorption is physical and endothermic, in agreement with experimental results. The negative value of ∆G° shows that the adsorption process is spontaneous. Positive ΔS° values indicate increased randomness at the solid/liquid interface, during adsorption of Cu2+ and Ni2+ cations onto the engineered bio-nanocomposite. The maximum adsorbed amounts of metal ions by the bio-nanocomposite used were 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ from single system. For the binary system, according to the Langmuir isotherm, the maximum adsorbed amounts of Ni2+ and Cu2+ were 357.14 mg/g and 370,37 mg/g, respectively. There is proof that Alginate-Moroccan clay bio-nanocomposites can serve as a different, less expensive source of sorbents for the removal of metal ions from single and binary systems.

As mitochondria are negatively charged organelles, penetrating cations are used as a part of the chimeric molecules to deliver the specific compounds into mitochondria. However, unmodified penetrating cations affect different aspects of cellular physiology as well. In this review we have attempted to summarize the data about side effects of the commonly used natural (e.gberberine) and artificial (e.g. tetraphenylphosphonium, rhodamine, methylene blue) penetrating cations on cellular physiology. For instance, it was shown that such types of molecules can (1) facilitate proton transport across membranes; (2) react with redox groups of respiratory chain; (3) induce DNA damage; (4) interfere with pleiotropic drug resistance; (5) disturb membrane integrity (6) inhibit the enzymes. Also, the products of the biodegradation of penetrating cations can be toxic. As penetrating cations accumulate in mitochondria, their toxicity is mostly due to the mitochondrial damage. Mitochondria of certain types of cancer cells appear to be especially sensitive to penetrating cations. Here we discuss the molecular mechanisms of the toxic effects and the anti-cancer activity of the penetrating cations.

Past public health crises (e.g. tobacco, alcohol, opioids, cholera, HIV, lead, pollution, venereal disease, even COVID-19) have been met with interventions targeted both at the individual and all of society. While the healthcare community is very aware that the global pandemic of non-communicable diseases (NCD’s) has its origins in our Western ultraprocessed food diet, society has been slow to initiate any interventions other than public education, which has been ineffective, in part due to food industry interference. This article provides the rationale for such public health interventions, by compiling the evidence that added sugar, and by proxy the ultraprocessed food category, meets the four criteria set by the public health community as necessary and sufficient for regulation — addiction, toxicity, ubiquity, and externalities (how does your consumption affect me?). To its credit, some countries have recently heeded this science and have instituted sugar taxation policies to help ameliorate NCD’s within their borders. This article also supplies scientific counters to food industry talking points, in order to guide both scientists and policy makers in instituting further appropriate public health measures to quell this pandemic.

Currently, there is a tenacious need to find new ways to purify water by eliminating bacterial biofilms, textile dyes, and toxic water pollutants. These contaminants pose significant risks to both human health and the environment. To address this issue, in this study, we have developed an eco-friendly approach that involves synthesizing Cobalt-doped Cerium Iron Oxide (CCIO) nanocomposite (NC) using an aqueous extract of Gossypium arboreum L. stalks. The resulting nanoparticles can be used to effectively purify water and tackle the challenges associated with these harmful pollutants. Nanoparticles excel in water pollutant removal by providing high surface area for efficient adsorption, versatile design for simultaneous removal of multiple contaminants, catalytic properties for organic pollutant degradation, and magnetic features for easy separation, offering cost-effective and sustainable water treatment solutions. CCIO nanocomposite has been synthesized by green co-precipitation method due to biomolecules and co-enzymes present in the aqueous extract of Gossypium arboreum L. stalk; a single-step procedure completed in 5 h reaction time. Further, the synthesis of nanocomposites was confirmed by various characterization techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermogravimetric analysis (TGA), Dynamic light scattering (DLS), and Energy Dispersive X-Ray (EDX). CCIO NCs were discovered to have a spherical shape and an average size of 40 nm. Based on DLS zeta potential analysis, CCIO NCs were found to be anionic. Also, CCIO NCs showed significant antimicrobial and antioxidant activity. Overall, considering the physical and chemical properties, the application of CCIO NCs in the adsorption of various dyes (~91 %) and water pollutants (chromium = ~ 60 %) has been considered since they exhibit great adsorption capacity owing to their microporous structure which can be a step forward in water purification.

The presence of harmful algal blooms (HABs) and cyanotoxins in drinking water sources poses a great threat to human health. The current study employed molecular techniques to determine the occurrence of non-toxic and toxic cyanobacteria species in the Limpopo River basin based on the phylogenetic analyses of 16S rRNA gene. The bottom sediments samples were collected from selected rivers: Limpopo, Crocodile, Mokolo, Mogalakwena, Nzhelele, Lephalale, Sand Rivers (South Africa); Notwane (Botswana), Shashe River and Mzingwane River (Zimbabwe). The physical-chemical analysis of the bottom sediments showed the availability of nutrients, nitrates and phosphates, in excess of 0.5 mg/l for most of river sediments, alkaline pH and salinity in excess of 500 mg/l. The FlowCam showed the dominant cyanobacteria species identified from the samples were Microcystis species, followed by Cylindrospermopsis raciborskii, Phormidium and Planktothrix species and this was confirmed by molecular techniques. Nevertheless, two samples showed the amplification of cylindrospermopsin polyketide synthetase gene (S3 and S9) while two samples showed amplification for microcystin/nodularin synthetase gene (S8 and S13). Thus these findings may imply the presence of toxic cyanobacteria species in the river sediments. The presence of cyanobacteria may be hazardous to human because rural communities and farmers who abstract water from Limpopo river catchment for human consumption, livestock and wildlife watering and irrigation.

This review article provides useful information on TiO2 and ZnO photocatalysts and their derivatives in removing organic contaminants such as different types of dyes, hydrocarbons, pesticides, etc. Also, the reaction mechanism of TiO2 and ZnO photocatalysts and their derivatives was investigated. In addition, the impact of adding metallic (e.g., Ag, Co, Pt, Pd, Cu, Au, Ni) and non-metallic (e.g., C, N, O, S) dopants to their structure on the photodegradation efficiency of organic compounds was thoroughly studied. Moreover, advantages and disadvantages of various synthesis procedures of ZnO and TiO2 nanocatalysts were discussed and compared. Furthermore, the impact of photocatalyst dosage, photocatalyst structure, contaminant concentration, pH, light intensity and wavelength, temperature and reaction time on the photodegradation efficiency was studied. According to previous studies, adding metallic and non-metallic dopants to the TiO2 and ZnO structure led to a remarkable enhance in their stability and reusability. Besides, doped TiO2 and ZnO demonstrated remarkable photocatalytic efficiencies in eliminating various types of organic contaminants.

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

We demonstrate a concept and fabrication of lithography-free layered metal-\ce{SiO2} thin-film structures which have reduced reflectivity (black appearance), to as low as 0.9~\%, with 4.9~\% broadband reflectance (8.9~\% for soda lime) in the 500 - 1400~nm range. The multi-layered (four layers) thin-film metamaterial is designed so that optical impedance matching produces minimal reflectance and transmittance within the visible and infra-red (IR) spectral region for a range of incident angles. The structure has enhanced absorbance and is easily tuned for reduced minimal transmission and reflection.

Nitrate and nitrite are the most extensively used food additives in the food industry for their multifunctional properties, and they have been in the spotlight for decades for its controversial back effects. The conversion of nitrate and nitrite to various nitroso compounds, specifically N-nitrosamine raises the question of the integrity of these additives. Nitrosamine is a well-known carcinogen and mutagen. A large number of studies demonstrate the carcinogenic effects of these salts. Are these findings credible? Nonetheless, the regulatory agencies approve its usage; is it biased? Are we feeding on the carcinogens in processed foods? The current work provides an insight into the basic and toxicological findings of the food additives -nitrate and nitrite.

Both Stevens Johnson Syndrome (SJS) and toxic epidermal necrolysis (TEN) are main injurious cutaneous medication reactions that mostly affect the epidermis and mucus membranes. TEN and SJS affecting nearly 1 or 2/1,000,000 people per year, and can recognized as medical crises since they may be deadly. Mucocutaneous discomfort, hemorrhagic erosions, erythema, and more or less severe epidermal separation that appear as ulcer and patches of dermic loss are their defining characteristics. The sole difference between TEN and SJS at this time is the degree of skin detachment, making them two extremes of a spectrum of severe cutaneous adverse drug reactions (cADRs). In the majority of cases, drugs are considered as the principal reason of SJS/TEN, but herpes simplex virus and Mycoplasma pneumoniae infections are also recognized causes, along with lesser number of cases in which the cause is still unknown. Among the drugs with a "high" likelihood of producing TEN/SJS are carbamazepine (CBZ), trimethoprim-sulfamethoxazole, phenytoin, aminopenicillins, allopurinol, cephalosporins, other sulfonamide antibiotics, quinolones, phenobarbital, and NSAIDs of the oxicam variety. There is strong genetic evidence for SJS and TEN in Han Chinese due to the substantial association between the human leukocyte antigen (HLA-B*1502) and SJS brought on by CBZ. The diagnosis is made mostly based on clinical symptoms and the histological study of a dermal biopsy. Pemphigus vulgaris, bullous pemphigoid, linear IgA dermatosis, paraneoplastic pemphigus, disseminated fixed bullous drug eruption, acute generalized exanthematous pustulosis (AGEP), and staphylococcal scalded skin syndrome (SSSS) are among the differential diagnoses. The management of patients with SJS/TEN is complicated by the high risk of mortality, necessitating early diagnosis, estimation of the SCORTEN prognosis, identification and discontinuation of the causative drug, specialized supportive care, and high-dose injectable Ig therapeutic interventions. The reported fatality rates for SJS are 1-5% on average and 25-35% for TEN; it can be even higher in patients who are elderly or who have a significant amount of epidermal detachment on their skin. More than 50% of TEN patients who survive the disease experience long-term consequences.

Organophosphate pesticides (also known OPPs) have for many years been the choice candidate globally for pest control. OPPs have for over 80 years, been used in gardens, fields and greenhouses as crop protection agents, and even in homes as insecticides and mosquito abatement. Thus, year after year and with the repeated application of organophosphate agents, many problems have appeared as a result of excessive use of pesticides. The adverse effects of pesticides are well documented in human health, environment, pesticide residue in crops, soil and water contaminated by these pesticides. Therefore, it is necessary to shed more light on the risks associated with the irresponsible usage of organophosphate pesticides.

The International Health Regulations (2005) promote national capacity in core institutions so countries can better detect, respond to and recover from public health emergencies. In accordance with the ‘all hazards’ approach to public health risk, this systematic review examines poisoning and toxic exposures in Myanmar. A systematic literature search was undertaken to find articles pertaining to poisoning in Myanmar published between 1998 and 2020. A number of poisoning risks are identified in this review including snakebites, heavy metals, drugs of abuse, agro-chemicals and traditional medicine. Patterns of poisoning presented in the literature diverge from poisoning priorities reported in other lower-middle income countries in the region. The expe-rience of professionals working in a Yangon-based poison treatment unit indicates that frequently observed poisoning as a result of substances including pharmaceuticals, methanol, and petroleum products were absent from the literature. Other notable gaps in the available research include assessments of the public health burden of poisoning through self-harm, household exposures to chemicals, paediatric risk and women’s occupational risk of poisoning. There is a limited amount of research available on poisoning outcomes and routes of exposure in Myanmar. Further inves-tigation and research is warranted to provide a more complete assessment of poisoning risk and incidence.

The altered nature of archaeological metals means they deteriorate at conditions where metals would be stable. The study of deterioration for such materials is hampered by their complexity, variability and difficulties in measuring deterioration. Placing an object in a sealed container, controlling the RH and pollutant gases and measuring any decrease in oxygen concentration is an accessible method to measure deterioration rate. It has been used for research into suitable environmental conditions to manage deterioration rates of such artefacts including differences in response for artefacts from different excavation sites. Some objects need careful control of RH to low values, this is expensive to maintain and poses risks to other artefacts displayed together. Many objects are actually stable up to quite high RH values and oxygen depletion testing has been used to identify those that can be safely displayed with minimal environmental control. The accelerated corrosion, ‘Oddy’ test is frequently used to sift out unsuitable display materials. The visual assessment is widely recognized to be subjective. The test container has been modified and oxygen depletion appears to give good quantitative measurements of corrosion that correspond with both visual comparison and corrosion quantification for copper, lead and steel, but not for silver.

Phase Change Materials (PCMs) are latent heat storage media with high potential of integration in building structures and technical systems. Their solid-liquid transition is commonly utilized for thermal energy storage in building applications. It also means that some kind of encapsulation is necessary. This is often solved with metal containers that also have high thermal conductivity and resistance to mechanical damage enhancing the performance these so called latent heat thermal energy storage (LHTES) systems. However selection of suitable metal is rather challenging. It depends, among other things, on the elimination of undesirable interaction between storage medium and surrounding metal. Heat storage medium must be reliably sealed in metal container especially when the storage system is integrated in systems like domestic hot water storage tanks, where PCM leaks can negatively affect human health. The aim of this study was evaluation of interaction between selected commercially available organic and inorganic PCMs and metals. The evaluation is based on the calculation of corrosion rate and use gravimetric method for determination of the weigh variations of the metal samples. Results show that aluminium is the most suitable container material with lowest mass loss and suffered only minimal visual changes on the surface after prolonged exposure to PCMs.

A procedure, dedicated to superconductivity, is extended to study the properties of interacting electrons in normal metals in the thermodynamic limit. Each independent-electron band is shown to split into two correlated-electron bands. Excellent agreement is achieved with Bethe's wave-function for the one-dimensional Hubbard model. The groundstate energy, reckoned for the two-dimensional Hubbard Hamiltonian, is found to be lower than values, obtained thanks to the numerical methods. This analysis applies for any spatial dimension and temperature.

The regeneration of bone tissue is a main purpose of most therapies in dental medicine. For bone regeneration, calcium phosphate (CaP)-based substitute materials based on natural (allo- and xenografts) and synthetic origins (alloplastic materials) are applied for guiding the regeneration processes. The optimal bone substitute has to act as a substrate for bone ingrowth into a defect, while it should be resorbed even in the time frame needed for complete regeneration up to the condition of restitution ad integrum. In this context, the modes of action of CaP-based substitute materials have been frequently investigated and it has been shown that such materials strongly influence regenerative processes such as osteoblast growth or differentiation and also on osteoclastic resorption due to different physicochemical properties of the materials. However, the material characteristics needed for the required ratio between the formation of new bone tissue and material degradation has not been found until now. The addition of different substances such as collagen or growth factors and also of different cell types have already been tested but did not allow for sufficient or prompt application. Moreover, metals or metal ions are differently used as basis or as supplement for different materials in the field of bone regeneration. Moreover, it has already been shown that different metal ions are integral components of bone tissue playing functional roles in the physiological cellular environment as well as in the course of bone healing. The present review focuses on frequently used metals as integral parts of materials designated for bone regeneration with the aim to give an overview of currently existing knowledge about the effects of metals in the field of bone regeneration.

The rapid technological development of society determined increased demand for safe potable water and food resources. Unfortunately, this progress causes complex environmental pollution, that is continuously challenging the scholars’ community. Therefore, it is important to chemically analyze the food for a better understanding of pollution-spreading mechanisms. Our study is focused on food analysis originating from Vatra Dornei City, which belongs to Suceava County in the Bukovina region of Romania. It represents a well-known Romanian spa and ski resort in the northern parts of the Oriental Carpathians Mountains. The mountain region owns a lot of mineral resources, mainly consisting of mineral and sparkling waters, uranium, manganese, copper, pyrite, chalcopyrite, polymetallic ores, baryte, gold and silver-bearing orebodies, etc. The present contribution aims to point out the results obtained from the analysis of soil, water and food samples collected from the local markets. The food samples consisted of lettuce, spinach, apples, pork (smoked) chicken meat (raw), milk and cheese. Last year the survey was conducted over six months. The results highlighted that the mining activities carried out during time caused environmental pollution with uranium and heavy metals due to the waste heaps’ weathering phenomena and tailing ponds’ presence.

Cohesion in the refractory metals Cr, Mo, and W is phenomenologically described in this work via a n-body energy functional with a set of physically motivated parameters that were optimized to reproduce selected experimental properties characteristic of perfect and defective crystals. The functional contains four terms accounting for the hard-core repulsion, the Thomas-Fermi kinetic energy repulsion and for contributions to the binding energy of s and d valence electrons. Lattice dynamics, molecular statics, and molecular dynamics calculations show that this model describes satisfactorily thermodynamic properties of the studied metals whereas, unlike other empirical approaches from the literature, predictions of phonon dispersion relations and of surface and point defect energetics reveal in fair good agreement with experiments. These results suggest that the present model is well adapted to large-scale simulations and whenever total energy calculations of thermodynamic properties are unfeasible

Rare earth elements (REEs) are a type of new material resources, which have attracted significant attention in recent years. REEs have emerged as essential metals in modern-day technology due to their unique functions. Long-term large-scale mining and utilization of rare earths have caused serious environmental pollution and constitutes a global health issue, which raised concerns about human health safety. However, the toxicity profile of suspended particulate matter of REEs in the environment interacts with the human body in remain largely unknown. Studies have shown that REEs can enter the human body through a variety of pathways, leading to a variety of organ and system dysfunctions through changes in genetics, epigenetics, and signaling pathways. Through an extensive literature search and critical analysis, we provide a comprehensive overview of the available evidence, identify knowledge gaps, and make recommendations for future research directions.

A paper in this journal on decamethylcyclopentasiloxane (D5) used unreliable methods to reach unreliable conclusions. The authors concluded that D5 exposure should be viewed as causing human reproductive disorders and should be considered a developmental toxicant, that is, toxic to the developing embryo. The inadequate methods could not have answered the authors' research questions, and the paper should be withdrawn.

For the better part of a century researchers across disciplines have sought to explain the crystallography of the elemental transition metals: hexagonal close packed, body centered cubic, and face centered cubic in a form similar to that used to rationalize the structure of organic molecules and inorganic complexes. Pauling himself tried with limited success to address the origins of transition metal stability. These early investigators were handicapped, however, by incomplete knowledge regarding the structure of metallic charge density. Here we exploit modern approaches to charge analysis to first comprehensively describe transition metal charge density. Then, we use topological partitioning and quantum mechanically rigorous treatments of kinetic energy to account for the structure of the density as arising from the interactions between metallic tetrahedra. We argue that the crystallography of the early transition metals results from charge transfer from the so called “octahedral” to “tetrahedral holes” while the face centered cubic structure of the late transition metals is a consequence of antibonding interactions that increase octahedral hole kinetic energy.

Adenylosuccinic acid (ASA) is a small molecule dicarboxylate that could be a strong clinical development candidate for inherited myopathies involving dysregulated purine nucleotide metabo-lism. Currently, there are no published pharmacokinetic/dynamic or toxicology data available, albeit 10-year clinical trial data in Duchenne muscular dystrophy patients suggests a chronically safe drug. In this study, we tested the toxicity of ASA to cultured myoblasts in vitro and acute systemic toxicity in mice. ASA is a non-toxic small molecule with an LD50> 5000mg/kg. Some background necrotic foci in the liver, kidney and gastrointestinal tract were shown that are likely incidental but warrant follow-up sub-/chronic oral exposure studies.

Food and drinks can be contaminated with pollutants such as lead and strontium and this poses a serious danger to human health. For this reason, a number of effective sensors have been developed for the rapid and highly selective detection of such contaminants. TBA, a well-known aptamer developed to selectively target and thereby inhibit the protein of clinical interest -thrombin, is receiving increasing attention for sensing applications, particularly for the sensing of different cations. Indeed, TBA, in the presence of these cations, folds into the stable G-quadruplex structure. Furthermore, different cations produce small but significant changes in this structure that result in changes in the electrical responses that TBA can produce. In this article we produce an overview of the expected data regarding the use of TBA in the detection of lead and strontium, calculating the expected electrical response using different measurement techniques. Finally, we conclude that the TBA should perform better as a detector of strontium rather than lead.

Current problem facing researchers globally is microplastics as well as toxic chemical pollution of the ecosystem. Microplastics carry toxic chemicals in the ecosystem.serving as a vector for transport. In this study, a review of the literature has been conducted with the following objectives: (1) to summarise the concentrations of toxic chemicals such heavy metals and hydrophobic organic contaminants sorped on microplastics; (2) to evaluate their spatial distribution regarding adsorbed contaminant (3) to discuss plausible mechanism by which microplastics adsorp or desorp toxic chemicals in the environment; (4) to discuss implications of their occurrence in air, water and soil media; and (5) to discuss the impact of ingested microplastics to human health. Microplastics are ubiquitous environmental contaminant. Concentrations of sorped toxic chemical varied with location which represents a local problem; industrialized areas (especially areas experiencing crude oil related activities or have history of crude oil pollution) have higher concentrations than less industrialized areas. Ingestion of microplastics has been demonstrated in a range of marine and soil organisms as well as edible plants, thus possible contaminating the base of the food-web. Potential health effect to human is by particle localization, chemical toxicity and microbal toxins. We conclude by highlighting the gap in knowledge and suggesting key future areas of research for scientists and policymakers.

The phenomena of electrical conductivity and electromigration in metallic systems are related, since in both cases the basic physical process is the scattering of conduction electrons by metal ions. Numerous searches have been made for equations connecting the conductivity with electromigration. In the case of a liquid metal, when using the Drude-Sommerfeld (DS) conduc-tivity equation, it was not possible to obtain a quantitative relationship between these phenomena, which would be correct. Attempts to find such a relationship when taking into ac-count the N. Mott correction (g - factor) in the DS equation were unsuccessful. This article proposes a different correction (b - factor) to the DS equation, which takes into account the pos-sibility of varying the momentum transferred by the conduction electron to a metal ion during the scattering. This correction allows to establish a quantitative relationship between conductivity and electromigration, as well as between electromigration in various binary systems with common components, in agreement with experiment. The proposed theory describes well, in particular, two- and multi-component metal systems of any concentration (the consistency rule for triangles A-B, B-C, C-A). The value of b - factor smoothly changes depending on the heat of vaporization of the metal, per unit volume.

In recent years, many researchers have begun to shift their focus onto the synthesis of nanomaterials as this field possesses immense potential that may provide incredible technological advances in the near future. The downside of conventional synthesis techniques, such as co-precipitation, sol-gel and hydrothermal methods, is that they necessitate the use of toxic chemicals, produce harmful by-products and require a considerable amount of energy; therefore, more sustainable fabrication routes are sought after. Biological molecules have been previously utilised as precursors to nanoparticle synthesis, thus eliminating the negative factors involved in traditional methods. In addition, transition-metal nanoparticles possess a wide scope of applications due to their multiple oxidation states and large surface areas; thereby allowing for a higher reactivity when compared to their bulk counterpart and rendering them an interesting research topic. However, this field is still relatively unknown and unpredictable. Therefore, this review aims to obtain a better understanding on the plant-mediated synthesis process of the major transition-metal and transition-metal oxide nanoparticles, and how different parameters affect their unique properties.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

Oil pollution of extraction areas is an undesirable phenomenon, but very present, es-pecially in old farms. In the context in which the depollution of these areas, in Roma-nia, is carried out from public funds, this fact is more and more difficult to achieve. That is why the effect of pollutants on the environment is being analyzed more and more, it often remains that the depollution is done naturally. This material analyzes the effect of metals present in crude oil (Cu, Pb, Zn, Ag, Ni, Mn, As, Cd, V, Cr, S), on the soil affected by a historical accidental pollution in the Moinesti area, Romania. This article presents the results of analyzes performed by metal detection techniques, namely optical emission spectrophotometry with inductive coupled plasma and atomic absorption spectrophotometry. The metals determined in the polluted soil were statis-tically analyzed regarding the dispersion, standard deviation and coefficient of varia-tion compared to the control sample and compared with the results from two areas in Romania. The risk of exploitation of polluted areas was also analyzed, namely the method of pollution indices and the method of combining the effects of pollutants

Constitutive models for plastic deformation of metals are typically based on flow rules determining the transition from elastic to plastic response of a material as function of the applied mechanical load. These flow rules are commonly formulated as a yield function, based on the equivalent stress and the yield strength of the material, and its derivatives. In this work, a novel mathematical formulation is developed that allows the efficient use of machine learning algorithms describing the elastic-plastic deformation of a solid under arbitrary mechanical loads and that can replace the standard yield functions with more flexible algorithms. By exploiting basic physical principles of elastic-plastic deformation, the dimensionality of the problem is reduced without loss of generality. The data-oriented approach inherently offers a great flexibility to handle different kinds of material anisotropy without the need for explicitly calculating a large number of model parameters. The applicability of this formulation in finite element analysis is demonstrated, and the results are compared to formulations based on Hill-like anisotropic plasticity as reference model. In future applications, the machine learning algorithm can be trained by hybrid experimental and numerical data, as for example obtained from fundamental micromechanical simulations based on crystal plasticity models. In this way, data-oriented constitutive modeling will also provide a new way to homogenize numerical results in a scale-bridging approach.

Maintaining sufficient levels of plant nutrients in the soil and controlling certain heavy metals, which can be toxic to the environment, are critical to ensure sustainable agricultural production. The study aimed to assess the linkage of crop-specific agricultural practices established by farmers in the Kvemo Kartli region (Georgia) with metal accumulation in soils of agricultural lands being subject to influence from polluted irrigation water in the past. In particular, we tried to identify the primary sources of micronutrients, including iron (Fe), copper (Cu), manganese (Mn), nickel (Ni), and zinc (Zn), and toxic elements such as cadmium (Cd) and lead (Pb), and share of the contaminated irrigation water and other factors related to agricultural practices under different land uses, such as intensive and extensive arable farming, vineyards, orchards, and permanent pastures having the least disturbed soil. Based on principal component analysis, five primary sources were identified and categorized according to farmers' interviews and previous studies conducted in the region. The results showed that increased concertation of plant-available Cu, Zn, Cd and Pb were mainly associated with irrigation water and intensive use of fungicides; Fe, Mn, and Ni were closely linked to several factors, such as the mineralogical composition of soils, mineral and organic fertilizers inputs, and atmospheric deposition from diffuse sources, where exhausts from transport are probably the primary source. During our study, we attempted to differentiate irrigation water inputs from fungicides using simulation based on irrigation pattern and irrigation water quality on the one hand and fungicide application rate and their metal content on the other. The simulation revealed that the intensive application of fungicides, especially in vineyards, is more significant in enriching soils with Cu and Zn than irrigation water. Identification of factorial dependences was supported by statistical analysis and application of a number of contamination assessment methods: Contamination Factor (CF), Pollution Load Index (PLI), single-factor Pollution Index (PI), Nemerow’s comprehensive pollution index (PIN), Enrichment Factor (EF), and Geo-Accumulation Index (Igeo). Applied environmental indices indicate that the soils under the former and existing vineyards are the most enriched with Cu and Zn, highlighting the significance of agricultural practices on heavy metals accumulation in soils of agricultural lands.

Sorghum is a multipurpose crop, but Cr(VI) toxicity influenced the production of the crop and have established highlighted courtesy, due to robust toxicity and a comparatively less known mode of action. Many reports approve the negative impact of Cr(VI) on plants. Yet, it is not clear that, at what concentrations, Cr(VI) inhibits the growth and nutrient quality of Sorghum. In the present research, toxic effects appeared after 1ppm of Cr treatment. The plant growth decreased 15 – 20% and nutritional quality decreased 30 – 40% significantly with increasing concentration of Cr(VI). Toxic components increased 14 – 16% with increasing concentration of Cr(VI) in both the varieties (HJ 541 and SSG 59-3). Chromium was accumulated more in roots followed by shoots with increasing Cr(VI) treatments (0-4 ppm). Chromium at 4ppm level was becoming lethal to Sorghum. Sorghum cultivar SSG 59-3 was more tolerable to Cr toxicity than HJ 541. Chromium accumulated in Sorghum and increased HCN content and at higher doses adversely affects the nutritive values and growth making it toxic for animal consumption. These findings may be useful for scheming a mitigation strategy for chromium toxicity.

The study of the distribution and health risk assessment is meaningful to provide basic data for environmental management．To investigate the pollution of potential toxic organics and their health risk to human beings, water samples were collected at 7 sites of main surface water of Beijing during wet and dry seasons respectively. The targeted 92 organics were detected, including phthalates (PAEs), volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs) and phenols. The results showed that: there were 56 organics detected out, and the number ratios of detected compounds to the total compounds of the same kind increased as the following: VOCs, phthalates, phenols, PAHs. 8 VOCs were detected in wet season, and 3 in dry season. The concentration of 2,2-Dichloropropane was highest as 10.62ug/L, while the concentrations of other VOCs were below 5ug/L; There were 11 phthalates detected during dry season. The content of Bis(2-methoxyethyl) phthalate was highest as 188.47ng/L; 17 phenols were found in samples during wet season, and the highest concentration was 1244.73ng/L for 4-nitrophenol; PAHs could be detected in all samples, and the detected compounds and the corresponding average concentrations were higher in wet seasons than those in dry seasons, which indicated that non-point pollution was possibly the main pollution source. The health risk assessment of the detected 56 pollutants by using a model from US EPA showed that, the risk caused by the four kinds of toxic organics in this study was in the acceptable ranges.

Metalloproteinases are zinc-dependent endopeptidases that function as primary effectors of tissue remodelling, cell-signalling, and many other roles. Their regulation is ferociously complex, and is exquisitely sensitive to their molecular milieu, making in vivo studies challenging. Phenanthroline (PhN) is an inexpensive, broad-spectrum inhibitor of metalloproteinases that functions by chelating the catalytic zinc ion, however its use in vivo has been limited due to suspected off-target effects. PhN is very similar in structure to phenanthrene (Phe), a well-studied poly aromatic hydrocarbon (PAH) known to cause toxicity in aquatic animals by activating the aryl hydrocarbon receptor (AhR). We show that zebrafish are more sensitive to PhN than Phe, and that PhN causes a superset of the effects caused by Phe. Morpholino knock-down of the AhR rescues the effects of PhN that are shared with Phe, suggesting these are due to PAH toxicity. The effects of PhN that are not shared with Phe (specifically disruption of neural crest development and angiogenesis) involve processes known to depend on metalloproteinase activity. Furthermore these PhN-specific effects are not rescued by AhR knock-down, suggesting that these are bona fide effects of metalloproteinase inhibition, and that PhN can be used as a broad spectrum metalloproteinase inhibitor for studies with zebrafish in vivo.

Wetlands are carriers of metals and organic pollutants from natural and anthropogenic sources. Studies have shown that sediments are sinks for these pollutants as they carry more than 99% of the total amount of metals which are released as soluble metals into the Lagoon. The University of Lagos, located at Akoka North eastern part of Yaba in Lagos Mainland runs along a highly industrialized and residential area. This paper reports the total metal concentrations in wetland and sediment and their seasonal variations. Wetland and sediment samples were collected for two seasons in 8 sampling sites. Results showed wetland data having lower concentrations of metals as compared to sediments. Wet season had higher concentrations of metals as compared to other season. Total concentrations in wetlands were Cd (1.0-6.0), Cu (1.0-11.0), Cr (0.3-82.7), Zn (2.7-65.0) and Pb (0.3-16.0) all in μg L-1 respectively. Statistical analysis showed that there was a significant difference between the wet and dry seasons for sediments. Cd was the only metal at acceptable levels while Cr, Cu, Pb and Zn concentrations all exceeded levels deemed acceptable by the SABS and the EPA. Therefore, the wetland is in poor health.

Huntington’s disease (HD) is a rare but progressive and devastating neurodegenerative disease characterized by involuntary movements, cognitive decline, executive dysfunction, and neuropsychiatric conditions such as anxiety and depression. It follows an autosomal dominant inheritance pattern. Thus, a child who has a parent with the mutated huntingtin (mHTT) gene has a 50% chance of developing the disease. Since HTT protein is involved in many critical cellular processes including neurogenesis, brain development, energy metabolism, transcriptional regulation, synaptic activity, vesicle trafficking, cell signaling, and autophagy, its aberrant aggregates lead to disruption of numerous cellular pathways and neurodegeneration. Essential heavy metals are vital at low concentrations, however, at higher concentrations, can exacerbate HD by disrupting the glial-neuronal communication, and/or causing dysbiosis (disturbance in the gut microbiota, GM), both of which can lead to neuroinflammation and further neurodegeneration. Here, we discuss in detail the interactions of iron, manganese and copper with glial-neuron communication and GM and indicate how this knowledge may pave the way for development of a new generation of disease-modifying therapies in HD.

In a constantly changing environment brought about by the climate crisis and escalated anthropogenic perturbations driven by the growing population, harmful algal bloom dynamics and their impacts are expected to shift, necessitating adaptive management strategies and comprehensive research efforts. Similar to primary productivity, HABs have been thought to be driven primarily by major nutrients such as N, P, and Si. However, recent investigations on the role and importance of micronutrients as limiting factors in aquatic environments have been highlighted. This paper provides a review of metal and phytoplankton interactions, with a specific emphasis on pertinent information on the influence of trace nutrients on growth, toxin production, and other underlying mechanisms related to the dynamics of HABs. Low to near-depleted levels of essential nutrients including Fe, Cu, Zn, Se, Mn, Co, and Mo, negatively impact cell growth and proliferation of various marine and freshwater HAB species. However, evidence shows that at elevated levels, these trace elements along with other non-essential ones, could still cause toxic effects to certain HAB species manifested by decreased photosynthetic activities, oxidative stress, ultrastructure damage, and cyst formation. Interestingly, while elevated levels of these metals mostly result in increased toxin production, Co (i.e., yessotoxins, gymnodimine, and palytoxins) and Mn (i.e., isodomoic acid, okadaic and diol esters) enrichments revealed otherwise. In addition to toxin production, releasing dissolved organic matter (DOM) including dissolved organic carbon (DOC) and humic substances was observed as an adaptation strategy, since these organic compounds have been proven to chelate metals in the water column, thereby reducing metal-induced toxicity. Whilst current research center on free metal toxicity of specific essential elements such as in Cu and Zn, a comprehensive account of how trace metals contribute to the growth, toxin production, and other metabolic processes under conditions reflective of in-situ scenarios of HAB-prone areas, would yield new perspectives on the roles of trace metals in HABs. With the growing demands of the global population for food security and sustainability, substantial pressure is exerted on the agriculture and aquaculture sector, highlighting the need for effective communication of information regarding the interactions of macro- and micronutrients with HABs to improve existing policies and practices.

Gas sensing is crucial for detecting hazardous gases in industrial environments, ensuring safety and preventing accidents. Additionally, it plays a vital role in environmental monitoring and control, helping to mitigate pollution and protect public health. Integrated photonic gas sensors are important due to their high sensitivity, rapid response time, and compact size, enabling precise recognition of gas concentrations in real-time. These sensors leverage photonic technologies, such as waveguides and resonators, to enhance performance over traditional gas sensors. Advancements in materials and fabrication techniques could further improve their efficiency, making them invaluable for environmental monitoring, industrial safety, and healthcare diagnostics. In this review, we delved into photonic gas sensors that operate based on the principles of evanescent field absorption (EFA) and wavelength interrogation methods. These advanced sensing mechanisms allow for highly sensitive and selective gas detection, leveraging the interplay of light with gas molecules to produce precise measurements.

Bacteria’s ability to withstand the detrimental effects of antimicrobials may take the form of resistance or tolerance with the minimum inhibitory concentration (MIC), the mutant prevention concentration (MPC), and the mutant selection window as salient concepts. Isolates exposed for 30 days to different concentrations of selected antibiotics, biocides, and heavy metals, singly and in combination, were additionally exposed to very high (15 × MIC) concentrations of ampicillin., and their tolerance was calculated the time to kill 99.9% of the isolate population (MDK99.9). These values were increased by 30 to 50% in test isolates compared to the untreated control. BAC 10-exposed isolates had the highest tolerance increase, and the tolerance appeared to originate from two sources, i.e., stochastic persistence and genetic-induced persistence, involving multiple genes using diverse mechanisms. The mutant selection window of the isolates to ampicillin, amoxicillin, and oxytetracycline also slightly increased compared to the control, indicating the amplification of persister cells during the 30-day exposure. These findings indicate that bacterial exposure to sub-inhibitory concentrations of environmental chemical stressors may not always result in the development of antimicrobial resistance but could initiate this process by selecting for persisters that could evolve into resistant isolates.

There is a need to search for new antifungals, especially for the treatment of the invasive Candida infections, caused mainly by C. albicans. These infections are steadily increasing at an alarming rate, mostly among immunocompromised patients. The newly synthesized compounds (3a-3k) were characterized by physico-chemical parameters and investigated for antimicrobial activity using the microdilution broth method to estimate minimal inhibitory concentration (MIC). Additionally, their antibiofilm activity and mode of action together with the effect on the membrane permeability in C. albicans were investigated. Biofilm biomass and its metabolic activity were quantitatively measured using crystal violet (CV) staining and tetrazolium salt (XTT) reduction assay. The cytotoxic effect on normal human lung fibroblasts and hemolytic effect were also evaluated. The results showed differential activity of the compounds against yeasts (MIC = 0.24-500 µg/mL) and bacteria (MIC = 125-1000 µg/mL). Most compounds possessed strong antifungal activity (MIC = 0.24-7.81 µg/mL). The compounds 3b, 3c, and 3e, showed no inhibitory (at 1/2 MIC) and eradication (at 8 x MIC) effect on C. albicans biofilm. Only slight decrease in the biofilm metabolic activity was observed for compound 3b. Moreover, the studied compounds increased the permeability of the membrane/cell wall of C. albicans and their mode of action may be related to action within the fungal cell wall structure and/or within the cell membrane. It is worth noting that the compounds had no cytotoxicity effect on pulmonary fibroblasts and erythrocytes at concentrations showing anticandidal activity. The present studies in vitro confirm that these derivatives appear to be a very promising group of antifungals for further preclinical studies.

Studies at the molecular, systemic, and epidemiological levels have shown that chronic metal exposure is linked to significant health consequences, including cancer, affecting hundreds of millions worldwide. Subtle and convoluted mechanisms underline metals' toxicity and carcinogenicity. The use of sensors for carcinogenic metals' trace detection is on the rise due to their selectivity, simplicity, and affordability. Biotechnology and microelectronics in the development of sensors have grown complementarily in recent years. This study offers a comprehensive overview of current research and advancements in developing sensors for detecting carcinogenic metals. Here, we have focussed on the developed biosensor platforms for group 1 carcinogens, i.e., arsenic, nickel, cadmium, chromium, and beryllium, along with their brief roles in human carcinogenesis. This review also looks at the importance of sensing such metal exposure in humans from a larger perspective, hoping to influence future research toward early prevention and treatment of illnesses like cancer.

Flammability was evaluated and the results showed the values of critical flux at extinguishment (CFE) as 49.5kW/㎡ on average, total heat release (Qt) as 0.21MJ on average, and peak heat release rate (Qp) as 0.66kW on average, which satisfied all of the thresholds presented by the IMO. Therefore, flame-retardant plywood, of which the flame-retardant performance was evaluated, was determined to be an applicable finishing material that satisfies fire safety standards.

The purpose of this paper is to test the Kuznets Environmental Curve (KEC) hypothesis for 10 MENA (Middle East and North Africa) countries during the period 1987-2017. To do this, the translogical functional form has been adopted to estimate the relationship between Toxic Gases (TG) emissions, energy consumption and GDP per capita. The results confirm the presence of KEC, GDP per capita and energy consumption have a positive influence on TG emissions, and the presence of a feedback relationship between GDP per capita and energy consumption. As a result, the environmental framework of the selected countries improves as their level of growth has become more advanced. In addition, to reduce TG emissions, MENA countries are expected to significantly increase the use of renewable energy and a more efficient energy policy.

Application of toxic antibacterial agents is considered necessary to control prevalent fresh water microorganisms in evaporative cooling water systems, but these agents can adversely affect the environment and human health. Alternatively, natural antibacterial water chemistry has been applied in industrial cooling water systems for over 10 years with excellent results. The tower water chemistry method concentrates natural salts in highly-softened water to produce elevated pH and dissolved solids, with low calcium and magnesium. This practice conserves water while generating only a small volume of non-toxic natural salt concentrate for cost efficient separation and disposal if required. This review presents a novel perspective of natural antimicrobial chemistry for inhibiting parasitic microbiome functional relationships within the bio-triad of Legionella outbreaks, "Trojan Protozoans" and biofilms. The review further examines practical application and function of polyvalent metal ions in the inhibition of biofilms. Reducing global dependence on toxic antibacterial agents discharged to the environment is an emerging concern due to their impact on the natural microbiome, plants, animals and humans. Discharge of antibacterial agents also contributes to development of pathogen resistance. Use of natural antibacterial chemistry can play a key role in managing the cooling water environment in a more ecologically sustainable manner.

This article presents the results of research on the influence of polymetallic dust aerial emissions on the pollution levels in the soil and plants by heavy metals which have been under impact of the “Severonickel” smelter complex on the Kola peninsula (Russia) for many years. Research using soil- and bio-indicators was carried out at fixed measuring points in the years 1980-1999 (high aerotechnogenic emissions) and 2000-2019 (low aerotechnogenic emissions). The organic horizon (forest litter) of the Al-Fe-humus podzol, leaves of Vaccinium myrtillus L., V. vitis-idaea L., V. uliginosum L., Empetrum hermaphroditum Hagerup and one-year old Scots pine needles Pinus sylvestris L. as well as tree rings of Pinus sylvestris L. were used for bioindication research. The content of heavy metals was determined by the AAS method. During these time periods, the volume of atmospheric emissions of sulfur dioxide decreased 5 fold, polymetallic dust by 3.5 times, while the level of forest litter pollution by heavy metals in the buffer zone increased by 2 times, and did not change significantly in the impact zone. The decrease in atmospheric emissions of pollutants led to a 1.5- fold increase in the width of the annual rings of pine trunks in the impact zone, while in the buffer zone the differences were insignificant. At present, the content of Ni and Cu in the leaves of the wild dwarf-shrubs and pine needles in the impact zone has decreased by 5 times compared with 1980-1999 due to a decrease in polymetallic dust on the leaf surface.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

It is important to develop new antibacterial drugs since the emergence of bacterial resistance to available antibiotics. Metal nanoparticles have the potential to combat antibiotic resistance and are effective antibacterial agents. Here, we demonstrate the biogenic production of zinc nanoparticles using Rhododendron arboreum stem bark. The biosynthesized ZnNPs were characterized through different analytical techniques such as UV-vis, FTIR, EDX, SEM, and XRD. Clinical isolates such as E. coli, S. aureus, and K. pneumonia were used to check the antibacterial efficacy of the biosynthesized zinc nanoparticles. The MIC and MBC values against K. pneumonia, S. aureu, and E. coli were found to be 34±0.21 and 11.71±0.47, 47±0.11 and 23.86±0.84 and 94±0.18 and 40.43±0.16 µg/mL, respectively. It dramatically decreased the integrity of the cell membrane and markedly increased the permeability of both inner and outer membranes. The green synthesized ZnNPs have good catalytic activity. It degraded 65% of methyl orange dye within 6h when the mixture was kept in direct sunlight, thus demonstrating good photodegradation potential and can be employed as a good photocatalyst. According to these results, biosynthesized zinc nanoparticles could be a potential therapy option for controlling bacterial pathogenesis and an effective photocatalyst for the elimination of hazardous water contaminants.

Imidazoline derivatives, such as xylometazoline, naphazoline, tetryzoline, tramazoline or oxymetazoline play an important pharmacological role as nasal drops in the symptomatic treatment of rhinitis. When comparing the toxicological data of these substances, it is noticeable that Oxymetazoline has an LD₅₀ value which is two orders of magnitude lower than all other imidazoline derivatives. Thus, ten vials of commercially available oxymetazoline nasal drops already contain a lethal amount. An explanation for this unusually high toxicity has not yet been found.

This work presents a heat transfer and boiling model that computes the evolution of the temperature field in a representative steel workpiece quenched from 850 or 930°C by immersion in water flowing at average velocities of 0.2 or 0.6 m/s, respectively. Under these conditions, all three boiling regimes were present during cooling: stable vapor film, nucleate boiling, and single-phase convection. The model was based on the numerical solution of the heat conduction equation coupled to the solution of the energy and momentum equations for water. The mixture phase approach was adopted using the Lee model to compute the rates of water evaporation-condensation. Heat flux at the wall was calculated for all regimes using a single semi-mechanistic model. Therefore, evolution of boiling regimes at every position on the wall surface was automatically determined. Predictions were validated using laboratory results, namely: a) Videorecording the upward motion of the wetting front along the workpiece wall surface, and b) cooling curves obtained with embedded thermocouples in the steel probe. Wall heat flux calculations were used to determine the importance of the simultaneous presence of all three boiling regimes on the heat flux distribution. It was found that this simultaneous presence leads to high heat flux variations that should be avoided in production lines.

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

Heavy metals are toxic, persistent and non-degradable. After sedimentation and adsorption, they accumulate in water sediments. The aim of this study was to understand the heavy metal pollution of Qinjiang River sediments on the ecological environment and apportioning sources. The mean total concentrations of Mn, Zn, Cr, Cu, and Pb are 3.14, 2.33, 1.39, 5.79, and 1.33 times higher than the background values, respectively, except for the Co, Ni, and Cd, which are lower than the background values; Fe, Co, Ni, Cd, Cr, Cu, and Pb are all primarily in the residual state, while Mn and Zn are primarily in the acid-soluble and oxidizable states, respectively. Igeo, RI, SQGs and RAC together indicate that the pollution status and ecological risk of heavy metals in Qinjiang River sediments are generally moderate; among them, Fe, Co, Ni, Cd, Cr, and Pb are not harmful to the ecological environment of the Qinjiang River. Cu is not readily released because of its higher residual composition, depicting that Cu is less harmful to the ecological environment. Mn and Zn, as the primary pollution factors of the Qinjiang River, are harmful to the ecological environment. This heavy metal pollution in surface sediments of the Qinjiang River primarily comes from manganese and zinc ore mining. Manganese carbonate and its weathered secondary manganese oxide are frequently associated with a significant amount of residual copper and Cd, as a higher pH is suitable for the deposition and enrichment of these heavy metals. Lead-zinc ore and its weathering products form organic compounds with residual Fe, Co, Cr, and Ni, and their content is related to salinity. The risk assessment results of heavy metals in sediments provide an important theoretical basis for the prevention and control of heavy metal pollution in Qinjiang River.

The separation and enrichment can be targeted to enrich the rare and precious metals in fly ash and reduce the cost of leaching and recovering of fly ash. Regarding their different properties, the single-component separation was used to obtain uncompleted burned carbon, glass microbeads, minerals, and other characteristic components from the ash. Also, the mineral composition of each component was analyzed by electron microscopy. The metal minerals were mainly concentrated in the mineral components. Besides, the electron probe micro-analysis shows that the Pt content in the minerals of fly ash was significantly correlated with the metal contents of Ni and Cu. After the obtainment of the characteristics of fly ash metal enrichment, the heavy minerals with Cu, Ni, Pt, Pd, and other target metal elements were enriched by gravity separation and flotation. The enrichment coefficients of Cu, Ni, Pt, and Pd were 1.45, 1.33, 1.90 and 1.60, respectively, and the recovery rates were 77%, 81%, 97% and 88% respectively. Since the yield of heavy minerals obtained by separation was 62.24%, it indicated the physical separation method could significantly reduce the cost of leaching and recovering of fly ash metal resources.

Groundwater plays a pivotal role as the largest potable water sources in Bangladesh. However, the quality of the groundwater faces challenges due to xenobiotic compounds in it. Excess amount of arsenic (As) has already been found in groundwater in many parts of Bangladesh. Thus, this study was conducted to assess the water quality and associated human health risk in central Bangladesh. A total of 99 groundwater samples from the central part of Bangladesh were analyzed to assess human health risk due to high level of nitrate (NO3-) and other trace elements i.e. arsenic (As), iron (Fe), and manganese (Mn). It was found that NO3- concentration (253.17 mg/L) in the groundwater samples exceeds the recommended guideline value by the WHO (50 mg/L). Moreover, this study area also characterized with elevated concentration of As (19.44 µg/L), Fe (811.35 µg/L), and Mn (455.18 µg/L) in the groundwater. Non-carcinogenic human health risk was calculated by justifying HQ (Hazard Quotient) and HI (Hazard Index) and attributed potential conjunctive human health risks due to NO3-, As, Fe and Mn in the study area. Moreover, high carcinogenic risk was found due to As contamination in the groundwater samples in the study area.

Monitoring water supply requires, among other quality indicators, the identification of the cyanobacte-ria community taking into account their potential impact in terms of water quality. In this work, cya-nobacteria strains were isolated from Cheffia reservoir and identified based on morphological features, 16S rRNA gene, phylogenetic analysis, and toxin production by PCR screening of the genes involved in the biosynthesis of cyanotoxins (mcyA, mcyE, sxtA, sxtG, sxtI, cyrJ, and anaC). Thirteen strains repre-senting six different genera: Aphanothece, Microcystis, Geitlerinema, Lyngbya, Microcoleus, and Pseudanabaena were obtained. The results demonstrated the importance of morphological features in determining the genus or the species when incongruence between the morphological and phylogenetic analysis occurs and only the utility of the 16S rRNA gene on determining higher taxonomic levels. The phylogenetic analysis confirmed the polyphyly of cyanobacteria for the Microcystis and Oscillatoriales genera. Unexpectedly, Aphanothece sp. CR 11 had the genetic potential to produce microcystins. Our study gives new insight instead of picocyanobacteria toxic genotype in this ecosystem. Thus, conven-tional water treatment methods in this ecosystem have to be adapted.

Thorium (Th) is a natural radioactive element present in the environment and has a potential to be used as a nuclear fuel. Relatively little is known about the influence and toxicity of Th in the environment. In the present study, the toxicity of Th to the green algae Chlorella pyrenoidosa (C. Pyrenoidosa) was evaluated by algal growth inhibition, biochemical assays and morphologic observations. In the cultural medium (OECD TG 201), Th(NO₃)₄ was transformed to amorphous precipitation of Th(OH)₄ due to hydrolysis. Th was toxic to C. Pyrenoidosa, with a 96 h half maximum effective concentration (EC₅₀) of 10.4 μM. Scanning electron microscopy shows that Th-containing aggregates were attached onto the surface of the algal cells, and transmission electron microscopy indicates the internalization of nano-sized Th precipitates and ultrastructural alterations of the algal cells. The heteroagglomeration between Th(OH)₄ precipitation and alga cells and enhanced oxidative stress might play important roles in the toxicity of Th. To our knowledge, this is the first report of the toxicity of Th to algae with its chemical species in the exposure medium. This finding provides useful information on understanding the fate and toxicity of Th in the aquatic environment.

The assessment of soil contamination in the vicinity of integrated siderurgical plants is of outmost importance for agroecosystems and human health, and sensitive techniques should be employed for accurate assessment of chemical elements (metals, potential toxic elements, rare earths, radioelements) in soil and further evaluation of potential ecological and safety risk. In this paper a total of 45 major, minor and trace elements (Al, As, Au, Ba, Br, Ca, Cd, Ce, Co, Cr, Cs, Cu, Dy, Eu, Fe, Hf, Hg, I, K, La, Mg, Mn, Mo, Na, Nd, Ni, Pb, Rb, Sb, Sc, Sm, Sn, Sr, Ta, Tb, Th, Ti, Tm, U, V, W, Y, Yb, Zn and Zr) were quantified in soils located around a large siderurgical works (Galati, SE Romania) using instrumental neutron activation analysis (INAA) in combination with X-ray fluorescence (XRF) and inductively coupled plasma mass spectrometry (ICP-MS). The statistical analysis results and vertical distribution patterns for three depths (0-5 cm, 5-20 cm, 20-30 cm) indicate inputs of toxic elements in the sites close to the ironmaking and steelmaking facilities and industrial wastes dumping site. For selected elements, a comparison with historical, legislated and world reported concentration values in soil was performed and depth migration, contamination and toxic risk indices were assessed. The distribution of major, rock forming elements was closer to the Upper Continental Crust (UCC), and to the Dobrogea loess, finding confirmed by the ternary diagram of the incompatible trace elements Sc, La and Th, as well as by the La to Th rate. At the same time, the La/Th vs. Sc and Th/Sc vs. Zr/Sc bi-plots suggested a felsic origin and a weak recycling of soils mineral components.

By using a two-stage physiologically based extraction test (PBET) and (W-PBET), the authors of this paper have estimated the bioaccessibility of metals (Pb and Fe) and their compounds in the GI tract of waterfowl and mammals. It has been shown that the metals (Pb and Fe) have low bioaccessibility; combined with the short time of shot exposition at the GI tract, this eliminates the risk of toxic effects in the case of shot ingestion by waterfowl. It has also been discovered that there is a significant difference in the bioaccessibility of metals and their compounds. A model was proposed and tested to predict the toxic effects of lead on biological objects depending on the threshold mass of consumption. This model takes into account data on the bioavailability of lead and regulatory values indicating dangerous concentrations of lead.

Heavy metals represent a class of chemical elements that includes metalloids, bases and transition metals, lanthanides and actinides. They are distinguished for their toxicity in small concentrations and for their negative effects on the environment and human health. They are present in various samples, mainly in water, industrial waste and food. The determination of heavy metals is carried out mainly by analytical methods, using spectroscopy, spectrometry and electroanalysis, while studies are being carried out for the development of new and faster methodologies and techniques for their analysis, with particular emphasis on voltammetry. This review deals with the determination of heavy metals mainly in environmental samples (water) using voltammetry. In particular, the methods of their determination are evaluated in terms of sensitivity, selectivity and applicability.

This study investigates the relationship between energy metals and precious metals to assess their suitability as safe haven assets in clean energy investment portfolios. It focuses on the impact of events in 2020 and 2022, characterized by substantial investments in clean energy. The research reveals that, except for Nickel Futures (NICKELc1), energy metals are positively linked with clean energy indexes. This suggests that they can serve as a secure investment option for green investors looking to diversify their portfolios. As a result, the study dismisses the initial question, indicating that energy metals can indeed be considered safe havens within the context of clean energy investments. Additionally, the research reinforces prior findings that precious metals like gold, silver, and platinum possess safe haven characteristics in relation to specific clean energy stock indexes. These results have significant implications, particularly given the increasing investments in clean energy stocks and the recurring uncertainties in the market. In summary, this study supports the idea that both energy metals and precious metals can play valuable roles in clean energy portfolios, providing stability during turbulent times in the market.

Certain studies have reported various insulin resistance responses to ambient heavy metal pollution, but few have reported such responses to occupational heavy metal pollution. Even fewer have demonstrated a relationship between mixture effects of heavy metals and insulin resistance in welding workers. Overall, we recruited 53 welders and 48 administrative staff from a shipyard located in northern Taiwan. Personal exposure to heavy metals was monitored for PM2.5 and urine. Blood samples from each participant were collected from the antecubital vein after fasting. Urine samples from each participant were collected in the same period as blood samples. The geometric mean levels for chromium (Cr), manganese (Mn), iron (Fe), cobalt (Co), nickel (Ni), copper (Cu), zinc (Zn), and cadmium (Cd) in the PM2.5 of the personal breathing zone and urinary Mn of welders were significantly higher than those in administrative staffs. Ambient Cr, Co, Ni, and Cu levels in the PM2.5 and urinary Cd were positively related to HOMA2-IR after adjusting for personal covariates (PM2.5-Cr: β=0.036, 95%C.I.: 0.002 to 0.070; PM2.5-Co: β=0.040, 95%C.I.: 0.002 to 0.077; PM2.5-Ni: β=0.054, 95%C.I.: 0.013 to 0.094; PM2.5-Cu: β=0.049, 95%C.I.: 0.010 to 0.088; U-Cd: β=0.209, 95%C.I.: 0.052 to 0.366, respectively). Our findings indicated the PM2.5 metal components and urinary metals were associated with increased insulin resistance in shipyard welders.

This investigation aimed to knowledge of the presence of Brucella spp .in the samples from Babylon province and the relationship with environmental factors. The seasonal collection of animal soil samples for various villages in the middle, south, and north of Babylon province, Hilla City, Iraq, with physicochemical parameters (air and soil temperature, pH, EC, TDS, salinity, TOC), as well as heavy metals (Fe, Cu, Cd, and Pb). The results showed the presence of Brucella species in some of soil samples and its percentage varies according to the four seasons, where the highest percentage of Brucella spp. was in summer season and the lowest in winter season and these percentages were related to seasonal environmental indicators. After sending the positive bacterial samples isolated from the soil for sequencing analysis, it was found that the bacterial samples isolated from the soil have new strains recorded in Genbank as following: five strains for Brucella intermedia and one strain for Brucella rhizosphaerae, Also, phylogenetic analysis was for the drawing of phylogenetic tree and the determination of phylogenetic relationship for Knowledge the degree of convergence between species and their source. Through our research, we concluded that proportion of Brucella spp. presence in summer was high and also environmental factors which included (Air and Soil temperature, pH, EC, TDS and Salinity) were high, except TOC was lower in summer season whereas heavy metals for Cu, Fe, Cd were lower in summer except Pb was high. This indicated that differences of seasons affect to Brucella ratio in soil. The findings of sequencing for the bacterial samples from soil demonstrated that B. intermedia was found in both the spring and fall seasons while B.rhizosphaerae found in the spring season , These types of Brucella had genetic variations. Also concluded that during phylogenetic analysis of the 16S rRNA sequences indicated that B.intermedia was nearest to Pakistan and other strain of B.intermedia was nearest to Russia while B.rhizosphaerae was nearest to Ukraine and Pakistan.

Printed Circuit Boards (PCBs) are essential to most electronic devices. Digitalization and upgradation of gadget generates lots of PCB-containing electronic waste. Conserving resources and protecting the environment requires recycling such e-waste. The present paper is focused on the recovery of metals from PCBs by physical pretreatment and hydrometallurgical processes. Initially, the waste PCBs were pre-treated to separate metallic and non-metallic fractions. The metallic concentrate was leached using nitric acid (strong oxidative agent) for dissolution of metals. The system was fully jacketed with scrubber and condenser so that no emission of toxic gases to the environment. The process parameters viz. effect of acid concentration, pulp density, temperature, time, etc. were optimized and the obtained data were scientifically validated. Kinetics leaching fitted well with the Shrinking core model, XB = kc.t for Cu, (1-(1-XB)1/2) for Ni and 1-3(1-XB)2/3 + 2(1-XB) for Pb. The optimized conditions derived from these studies will be useful for recovery of metals from waste PCBs, and tin left in the residue could be further treated for the purpose of safe disposal or the utilization in an environmentally friendly manner. The developed process provides environmental benefits and has potential to be commercialized after scale-up studies.

In this work, we investigate by ab initio calculations and optical experiments the sensitiv- ity of graphene quantum dots in their use as devices to measure the presence, and concentration, of heavy metals in water. We demonstrate that the quenching or enhancement in the optical response (absorption, emission) depends on the metallic ion considered. In particular, two test cases of opposite behaviour are considered: Cd 2+ , where we observe an increase in the optical response for increasing concentration, and Pb 2 whose emission spectra are quenched along the concentration rise. We envisage that quantum dots of graphene may be routinely used as cheap detectors to measure the degree of poisoning ions in water

The fundamental mechanism underlying negative-ion catalysis involves bond-strength breaking in the transition state (TS). Doubly-charged atomic/molecular anions are proposed as novel dynamic tunable catalysts and demonstrated in water oxidation to peroxide. Density Functional Theory TS calculations have found tunable energy activation barrier reduction ranging from 0.030 eV to 2.070eV, with Si²ˉ, Pu²ˉ, Pa²ˉ and Sn²ˉ the best catalysts; the radioactive elements usher in new application opportunities. C₆₀²ˉ reduces significantly the standard C₆₀ˉ TS energy barrier while graphene increases it, behaving like cationic systems. Rank-ordered catalysts according to their reaction barrier reduction efficiency, variation across charge states and systems reveal their tunable and wide applications, ranging from water purification to biocompatible anti-viral and anti-bacterial sanitation systems.

The aim of this study was to provide information on the levels of toxic (Cd and Pb) and essential (Cu, Fe and Zn) elements in cow’s milk produced in the State of Pernambuco (Brazil). A total of 142 samples of raw milk were collected, and the concentrations of essential and toxic elements were determined by inductively coupled plasma-optical emission spectrometry. In almost 30 % of the samples analyzed, the Pb content exceeded the maximum level established in the Brazilian legislation (0.05 mg/l). By contrast, in all samples the Cd content was below the maximum allowable level (0.02 mg/L). The essential trace elements Cu, Fe and Zn were generally present at lower concentrations than reported in other studies and can be considered within the deficient range for cow’s milk. Statistical and chemometric procedures were used to evaluate the main factors influencing the metal concentrations (proximity to major roads, presence of effluents, and milking method). The study findings demonstrate that the proximity of the farms to major roads influences the concentrations of Cd, Pb and Cu and that this is the main factor explaining the Pb content of milk. In addition, the presence of effluents influenced the concentrations of Cu, while no relationship between the metal content and the milking method was observed. Thus, in accordance with the study findings, consumption of cow’s milk produced in the region can be considered a risk to public health due to the high concentrations of Pb and the low concentrations of other essential minerals such as Cu, Zn and Fe in some of the milk samples.

The growing production and application of carbon-based nanomaterials (CNMs) represent possible risks for aquatic systems. However, the variety of CNMs with different physical and chemical properties, and different morphology complicated the understanding of their potential toxicity. This paper aims to evaluate and compare the toxic impact of four most common CNMs, namely multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO) in marine microalgae Porphyridium purpureum. The microalgae cells were exposed to the CNMs for 96 h and measured by flow cytometry. Based on the obtained results, we determined no observed effect level (NOEL), calculated EC10 and EC50 concentrations for growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species (ROS) generation changes for each tested CNMs. According to the sensitivity (growth rate inhibition) of P. purpureum, the used CNMs can be listed in following order: CNTs > GrO > Gr > C60. The toxicity of CNTs was significantly higher than the toxic effect of the other used CNMs and only this sample caused increase of ROS generation in microalgae cells. This effect caused by trace metal residuals in CNTs and high affinity between particles and microalgae associated with the presence of exopolysaccharide coverage on P. purpureum cells.

Background: Medicinal plants are of great importance to health of individual and communities. About 80% of the population in Uganda relies on traditional medicine because western-trained medical personnel are limited especially in villages. Most Ugandans use Hymenoxys odorato for medicinal purposes e.g. to treat colds, fever, coughs, anti-helminthes, locally used as tea, anti-allergy and also as an anti-venom to relieve snake bites. Method: A group of 25 male wistar rats of 150 g–210 g were kept for 14 days while being fed and treated with the extract. At 14^th day, anesthesia was given and blood samples collected by cardiac puncture for hematological and biochemical investigations. Serum was analyzed for Alkaline Phosphatase, Aspartate Transaminase and Alanine Transaminase while whole blood was used for complete blood count. The liver and kidney were removed and placed in 10% formalin to prepare for histology staining using haematoxylin and eosin technique. Results: The extract elevated hepatic biomarker enzymes i.e. ALP, ALT and AST. The increase was found to be significantly different (P > 0.05) at 400 and 500 mg/kg doses as compared to the control group. Histological sections of the liver showed distortion of liver cytoarchitecture, steatosis, necrosis of hepatocytes and congestion of the sinusoids at high doses 300, 400 and 500 mg/kg body weight. In the sections of the kidney, there was mild distortion of the integrity of the kidney with glomerular hypercellularity at high doses (400 and 500 mg/kg per body weight). Conclusion: Hymenoxys odorato aqueous extract has toxic effects on the liver and kidney of wistar rats. The effects were observed to be in a dose dependent manner.

In this study, multi-layer ceramic capacitors (MLCCs) detached from lighting sector's waste electrical-electronic equipment (WEEE) are characterised for the presence of rare earth elements (REEs) and precious metals (PMs). Their digestion was carried out with HNO3 & aqua regia on a heating plate and characterised with the use of inductively coupled plasma optical emission spectroscopy (ICP-OES) & scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The contents of REEs and PMs are 0.84 wt% and 0.60 wt%, respectively, and create an economic stored value in MLCCs that is essentially defined by PMs of 98.67% and by Pd 78.37%. The content of the main elements is: Nd 0.366 wt%, Y 0.220 wt%, Dy 0.131 wt%, Ag 0.467 wt%, and Pd 0.105 wt%. The results confirm the need of selective removal and separate recycling process of MLCCs from WEEE drivers.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

Zeolite Y with microporous and hierarchical structure containing Ti–Ni and Ti–Co oxides were obtained as active photocatalysts. Different Ti amounts (5, 10% TiO2) were supported, followed by loading of Ni or Co oxides (5 %). The X-ray diffraction evidenced the presence of TiO2 as anatase. N2 adsorption-desorption results showed type IV isotherms, for hierarchical zeolite Y samples, and a combination of type IV and I isotherms, for zeolite Y samples. UV–Vis diffuse reflectance spectra showed shift of absorption band to visible with increasing of Ti loading and especially after Co and Ni addition. A significant effect of the support was evidenced for Ti and interaction with Co/Ni species. The zeolite Y support stabilizes Ti in the 4+ oxidation state while hierarchical zeolite Y support favored the formation of Ti 3+ species and oxidation of Co and especially of Ni to 3+. Photocatalytic activity, under UV and visible light, was evaluated in degradation of amoxicillin, used as a model test. The photocatalytic mechanism was investigated using ethanol, p-benzoquinone and KI as ·OH, ·O2- radicals and hole (h+) scavengers. The best results were obtained for the immobilized Ni-Ti species on hierarchical zeolite Y support.

Many (if not a very large number) of metals and alloys evince substantial softening with torsion deformation to strains not usually achievable in tension. Of course, softening has long been observed by discontinuous dynamic recrystallization (DDRX) but this paper will discuss cases where softening is associated by texture development with large-strain deformation that is not reliant on changes in the dislocation hardening. This paper reviews the work of the current authors on FCC metals and alloys in this area and extends to a new discussion of BCC and HCP cases.

Carbon dioxide has become a global challenge, where the emissions have become more than what could be handled. In this regard, conversion of CO2 to value added chemicals and thus recycling CO2 became a viable option. One of these options is the use of a process in strong development: oxycombustion. However, the gases resulting from this process contain some traces of impurities that can hinder the recovery of CO2 such as NO and CO. This work has therefore focused on the study of the reaction of NO reduction by CO in an oxidizing medium, using catalytic materials based on various supported noble metals. These materials were extensively characterized by a variety of methods including BET surface area measurements, hydrogen chemisorption, Transmission Electron Microscopy (TEM) and H2 temperature programmed reduction (H2-TPR). The obtained results show that the catalytic behaviour of M/Al2O3 catalysts in CO oxidation and NO reduction with CO in oxidative conditions depends mainly on the nature of the metal. The best result for these both reactions is obtained with Pt/Al2O3 catalyst. The Pt nanoparticles existing in the metallic form (Pt°) showed by TPR could explain the activity.

The relative dislocation density of aluminum and copper samples is quantitatively measured using linear Resonant Ultrasound Spectroscopy (RUS). For each metallic group, four samples were prepared with different thermomechanical treatments in order to induce changes in their dislocation densities. The RUS results are compared with Nonlinear Resonant Ultrasound Spectroscopy (NRUS) as well as Second Harmonic Generation (SHG) measurements. NRUS has a higher sensitivity by a factor of two to six and SHG by 14% to 62%. The latter technique is, however, faster and simpler. As main a result we obtain a quantitative relation between the changes in the nonlinear parameters and the dislocation density variations, which in a first approximation is a linear relation between these differences. We also present a simple theoretical expression that explains the better sensitivity to dislocation content of the nonlinear parameters with respect to the linear ones. X-Ray diffraction measurements, although intrusive and less accurate, support the acoustics results.

Antimicrobial resistance (AMR) has a significant global impact on human, animal, and environmental health. Misuse and overuse of antibiotics in clinical and animal production settings are the main drivers behind the emergence of antimicrobial resistant bacteria. However, other compounds with antimicrobial activity may also contribute to this global public health problem. The aim of this comprehensive review is to provide detailed insights into the impact of metals and organic acids on the emergence and spread of AMR in the food chain, for which their role is not fully understood. The review examines the widespread use of organic acids in the food industry as feed additives or disinfectants, the crucial role of copper in animal growth and the harmful effects of mercury and arsenic as pollutants in food-producing environments. Additionally, it explores the antimicrobial mechanisms of metals and organic acids, the tolerance mechanisms developed by bacteria, and the interplay between genes responsible for metal tolerance and AMR. The comprehensive and integrated data presented highlights the need to further explore and understand the role of metals and organic acids as drivers of AMR to develop well-defined strategies effectively mitigating the AMR crisis within the food chain context.

Molten LiCl-KCl salt and liquid cadmium are proposed as the electrolyte and the reactive cathode for the electrorefining of spent nuclear fuels. Corrosion testing of existing alloys is mandatory to ensure the service life of the electrorefiner vessel and electrode assemblies. Haynes C276, Inconel 600, AISI 316L stainless steel, and 42CrMo low alloy steel were exposed to LiCl-KCl melt at 500°C for 500 h in an argon atmosphere. All alloys suffered from dissolution attacks with the presence of oxide islands or porous oxide layer on the surface. AISI 316L, T91 steel and tungsten specimens were also submitted to corrosion tests in liquid cadmium at 500°C for 120 h. Corrosion of AISI 316L and T91 stainless steel were predominated by chemical oxidation with additional severe Ni dealloying occurred on AISI 316L. Tungsten only suffered from dissolution attack in comparison.

Glutamate excitotoxicity is implicated in the pathogenesis of many disorders, including stroke, traumatic brain injury, and Alzheimer’s disease, for which central insulin resistance is a comorbid condition. Massive glutamate release primarily through ionotropic N-methyl-D-aspartate receptors (NMDARs) causes a sustained rise in [Ca2+]i, followed by mitochondrial depolarization and an increase in intracellular O2• (superoxide) production. Recently, we found that insulin protected neurons against excitotoxicity by diminishing the delayed calcium deregulation (DCD), However, a role of insulin in superoxide production in excitotoxicity still needs to be clarified. The present study is aimed to investigate the effects of insulin on glutamate-evoked superoxide generation and DCD using the fluorescent indicators dihydroethidium, MitoSOX Red, and Fura-FF in rats cultured cortical neurons. We found that insulin significantly diminished both the intracellular and mitochondrial superoxide production in neurons exposed to glutamate and there was a strong linear correlation between [Ca2+]i and intracellular superoxide. MK 801, an inhibitor of NMDAR-gated Ca2+ influx, completely abrogated the glutamate effects in both the presence and absence of insulin. In experiments on sister cultures, insulin diminishes neuronal death. Thus, collectively, data obtained suggest that insulin diminishes glutamate-induced superoxide production in neurons via fall of [Ca2+]i increased and thereby improves viability of neurons

The hazard and the carcinogenic risks due to the exposure to some potentially toxic elements by the Santiago Island (Cape Verde) population where calculated, considering soil ingestion, inhalation and dermal contact as exposure pathways. The topsoil of Santiago Island is enriched in Co, Cr, Cu, Ni, V, Zn, Mn and Cd to upper crust values. Hazard indices (HI) were calculated for these metals and As exposures, of Santiago Island population and the calculations were performed for children and adults. For children HI are higher than 1 for Co, Cr and Mn. So there is indication of potential non-carcinogenic risk for children, due to the high Co (HI=2.995), Cr (HI=1.329) and Mn (HI=1.126), values in soils. For the other elements and for adults there is no potential non-carcinogenic risk. Cancer risk was calculated for As, Cd, Cr and Ni exposures, for adults and children and the results are always lower than the carcinogenic target risk of 1x10-6, for As, Cd, and Ni. However, cancer risk are higher than the carcinogenic target risk for Cr, for adults. Regarding As, for children the fraction due to Riskingestion represents 51.6%, while Riskinhalation represents 48.0% and Riskdermalcontact represents only 0.4% of total risk. For adults Riskinhalation represents 81.3%, Riskingestion represents 16.6% and Riskdermal contact represents 2.1%. These results reflect the higher daily ingestion dose for children and the higher inhalation rate and higher dermal contact surface for adults. For the other elements and for adults the cancer risk due to Cr, Ni and Cd inhalation is always higher than for children, reflecting the higher inhalation rate for adults.

In this study, sodium alginate (SA) was oxidized with potassium periodate to produce an alginate-based tanning agent. Using OSA as a biodegradable tanning agent and a nano-hydroxyapatite (nano-HAp) low concentration suspension to give flame retardancy to leather, eco-design concepts were applied to establish a chrome-, aldehyde-, and phenol-free tanning process. Micro-DSC, 1H NMR, attenuated total reflection mode Fourier transform infrared spectroscopy (FTIR-ATR), and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) were used to investigate the complex matrix collagen-OSA-nano-HAp. Micro-differential scanning calorimetry (micro-DSC) was used to assess OSA's ability to interact with collagen and stabilize the collagen-OSA matrix, while 1H unilateral nuclear magnetic resonance (NMR) was used to investigate the aqueous environment and limitations around collagen molecules caused by their association with OSA and nano-HAp. Industrial standard tests were used to assess mechanical properties and fire resistance of the new leather prototype. The findings reported here indicate that both OSA and nano-HAp are suitable alternatives for cleaner tanning technologies and more sustainable leather.

The mechanism of vapor-gas deposition of vinyltrimethoxysilane (VS) and ethylene glycol (EG) from azeotropic solutions is investigated, which allows to reduce the evaporation temperature of the components of working mixtures. The need for such studies is associated with the development of a new direction in the technology of vapor-gas deposition of polymer coatings. Methods have been developed for monitoring the chemical composition of working solutions in evaporators using optical spectroscopy, which allow calculating the partial pressures of vapor phase components. Based on these studies, compositions of working solutions are proposed that allow to equalize the partial pressures of the components of working mixtures with a large difference in boiling point. A new method of vapor-gas deposition of non-volatile powder inhibitors on metals is proposed. Chemical compositions of siloxane coatings were determined using XPS and mechanisms of interaction of VS with polymerization promoters ethylene glycol and 1-hydroxy ethylidene-1,1-diphosphonic acid (HEDP) were proposed.

Plants have the ability to decrease the pollution level from the environment by absorbing inorganic/organic pollutants through their roots. After that, these pollutants are translocated or accumulated in less toxic forms in various parts of plants. This ability of plants is known as phytoremediation. It is an eco-friendly, and cost-effective approach for controlling environmental pollution. It can provide a sustainable way to improve the economics of developing countries. However, the biomass formed during this process can re-contaminate the environment through secondary pollutants. The contamination due to heavy metals (HMs) has become an environmental challenge globally. Metals such as cadmium (Cd), chromium (Cr), mercury (Hg), arsenic (As), nickel (Ni), lead (Pb), etc. can enter the water and soil largely through anthropogenic activities as well as other natural processes. After that, these metals pose a severe threat to living organisms. Due to their non-biodegradable nature, these metals can remain as such for a long time. These metals can initiate oxidative pressure in plants as a result affects agricultural production and yield. To mitigate this problem, phytoremediation has come forward as a safe, affordable, and ecologically sustainable solution than conventional physicochemical decontamination methods. Initially, several edible crops had been identified for the remediation. But at the present time, scientists are focusing on non-edible crops like aromatic/medicinal plants. There is no risk of food contamination by using these plants. This chapter describes the classification & uses of Tulsi and the phytoremediation mechanism of plants in detail.

This paper focuses on the application of principal component analysis (PCA) to conduct a source apportionment of atmospheric aerosols from 8 sampling locations along the Marilao-Meycauayan-Obando River System (MMORS). Aerosols were collected on May 2016 during the same time that water samples were collected. Elemental analysis was conducted using a scanning electron microscope coupled with energy dispersive x-ray (SEM-EDX). Carbon (C), nitrogen (N), oxygen (O), sodium (Na), magnesium (Mg), aluminum (Al), silicon (Si), sulfur (S), chlorine (Cl), potassium (K), calcium (Ca), titanium (Ti), manganese (Mn), iron (Fe), copper (Cu), zinc (Zn), bromine (Br), niobium (Nb), barium (Ba), mercury (Hg), and lead (Pb) concentrations were measured and used as inputs in Principal Component Analysis (PCA). The aerosol samples showed the presence of heavy metals Pb and Hg, elements that were also detected in trace amounts in the water measurements. Concentrations of heavy metals Fe, Pb, Hg in the aerosols were attributed to industrial sources. However, it was determined that the primary source of aerosols in the area were traffic and crustal emissions (C, N, O, Si, Al, Ca). Thus, control of traffic emissions would be more beneficial in reducing aerosol emissions in Meycauayan.

This study was conducted to recover valuable metals (silicon and silver) using acid leaching and substitution reactions with copper powder from the pulverized solar cell separated from the PV ribbon. Leaching experiments were conducted according to nitric acid concentration by molar solution as 1M, 2M, and 3M using an ultrasonic cleaner at a reaction temperature of 60 °C for the leaching times of 30 to 120 minutes. Si phases were detected at all leaching reaction times, it was confirmed that the aluminium was removed effectively if the nitric acid leaching time was more than 30 minutes, and silicon with a purity above 99% could be recovered. The silver was precipitated by adding copper, which has greater reducibility than Cu, Al, Si, Pb, and Sn. When the addition of copper powder was 0.75 and 1.0 g, precipitate was produced 0.23 and 0.55 g, respectively. The optimal condition for the recovery of silver by the addition of copper powder was 1 g, where is recovery rate reached 93.3%.

Water contamination has intensified over the year as the world's population and industrial activities have grown. Heavy metals (HMs) are amongst the environmental contaminants commonly found in water and wastewater. These include Lead, Manganese, Chromium, Mercury, etc. Various techniques have been used to remediate this environmental challenge and adsorption has proven to be more effective because it is simple to use, excellent efficiency, low cost, possibility to operate in several experimental conditions. Regrettably, this method yields waste materials, which represents a scaling restriction. Furthermore, after the HM has been removed and loaded onto the adsorbent, there is still a question of the fate of the metal-loaded adsorbent. Most of the time these metal loaded adsorbents are discarded in the environment and constitute a secondary pollution. New applications for heavy metals laden have been investigated. This review article presents the various applications that had been investigated to reuse the loaded metal adsorbent. A case study on developing tools for combatting gender-based violence (GBV) has also been discussed.

In this study, we attempted to verify the hypothesis that total metals bound to dust of different particle sizes may reflect pollution levels, but cannot predict its bioavailability and risks in human health assessments. Dust samples were collected using active sampling method; during the dry season months of November, 2014 to March, 2015 at different locations in Akure (7˚10ʹN and 5˚15ʹE). The samples were sorted into different particle sizes (< 10µm, 10 – 50 µm, >50µm), analyzed for some physicochemical properties and assessed for metals bioavailability using two-step physiological extraction method. The amount of metals (Cd, Cu, Cr, Ni, Pb, Zn and Mn) released in each particle sizes were determined using Perkin-Elmer 6000 Inductively Coupled Plasma - Atomic Emission Spectrometry (ICP-AES) analysis. The results showed that bioavailability of some metals (Cd, Ni, Pb, and Zn) decreases with increasing particle sizes, however, the reverse trend was observed for Mn, Cu and Fe concentrations. This may be attributed to some combination of physicochemical characteristics of the dust and metal speciation. Hence, it was concluded that metal bioaccessibility in dust can best be described by the knowledge of physicochemical characteristics. The exposure dose of the metals showed that cancer risks due to inhalation were very high when compared to other exposure routes (ingestion and dermal contact). The calculated non-cancer (HQ) and cancer risk (HI) for humans in the area showed values higher than unity, indicating possibility of the metals’ body burden.