Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyses the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% of nano-TiO2 and compares it to the transparent base binder, and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier-Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity and exhibited values between the conventional binder and PMB regarding rutting resistance, penetration, and softening point. They showed similar behavior as the PMB, demonstrating signs of polymer-modification. The addition of TiO2 seems to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increases the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, considering fatigue and 10.0% concerning permanent deformation.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

Until now, crystalline NiCo2S4 and its composites have demonstrated improve performances in supercapacitor applications, compared to their oxide analogous, due to their relatively higher electrical conductivity, and multifaceted redox reaction. However, amorphous phase materials have recently shown promise in electrochemical energy storage systems. In this work, urea-assisted amorphous NiCo2S4 on nickel foam (referred to as aNCS) with high nitrogen atom% content, was obtained via hydrothermal method. In comparison to the crystalline NiCo2S4 (referred to as cNCS), aNCS exhibited superior electrochemical performance with specific capacitance of ~3506 F g-1 which is higher than cNCS specific capacitance of ~2185 F g-1 at 2 A g-1. Additionally, aNCS in two-electrode asymmetry supercapacitor exhibited specific capacitance and energy density of ~196 F g-1 and 56 Wh kg-1, respectively.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

This research investigates the application of Fused Filament Fabrication (FFF) in producing WC-10Co hardmetals, focusing binder formulations and understanding its influence on extrusion force and the influence of printing variables on green density of the samples. By examining the interplay between different binder compositions and backbone contents, the study aims to enhance the mechanical properties of the sintered parts while reducing defects inherent in the printing process. Evidence suggested that formulated feedstocks influenced the hardness of the sintered hardmetal, not due to microstructural changes but to macrostructural responses like macro defects introduced during printing, debinding and sintering of the samples. The results demonstrate the critical role of PP-MA content in improving part density and sintered hardness, suggesting the need for specific thermal debinding protocols tailored to each feedstock. The study provides insights into the formulation of feedstocks for hardmetal FFF, proposing a path toward refining manufacturing processes for better quality and performance of 3D printed hardmetal components.

Background: Fibromyalgia patients suffer from widespread chronic pain throughout the musculoskeletal system. There are no apparent clinical visible symptoms, and the syndrome lacks a clear medical explanation. Female fibromyalgia patients often feel they suffer from a transparent disease which is not acknowledged as an illness by their social circle. Hence, they are often exposed to skeptics and critics. One of the challenges fibromyalgia patients faces is to convince their surroundings that they are in pain and accept the presence of the invisible disease and the chronic pain in their lives. A multidisciplinary Fibrotherapy treatment model, implemented at the Ezra Le'Marpeh Rehabilitation Center, supports female fibromyalgia patients through a holistic mind-body approach, delivered in three 10-week cycles totaling 30 weeks of treatment. The research aims to understand the experiences of female fibromyalgia patients who perceive themselves as suffering from an invisible disease and the personal and familial aspects of transitioning from lack of acceptance to coping with reality and adaptation. Methods: We interviewed 16 female fibromyalgia patients in Israel and qualitatively analyzed the data using the Grounded Theory approach. Results: Following participation in the program, the fibromyalgia patients accepted the presence of the disease in their lives and changed their attitude toward the disease and its consequences. Conclusions: As fibromyalgia symptoms are invisible and can suddenly burst into their lives without warning, female fibromyalgia patients often face skepticism from their social circle and have self-doubt. Therefore, participating in holistic intervention programs may improve how they accept the disease and come to terms with its existence by taking a proactive coping approach.

This review paper explores the innovative realm of transparent solar panels, investigating their properties, applications, challenges, and recent advancements. Transparent solar panels, designed to harvest solar energy while allowing visible light to pass through, have gained significant attention due to their potential to revolutionize renewable energy technologies. The paper delves into the working mechanisms of various types of transparent solar panels, including Organic Photovoltaic (OPV) panels, Dye-Sensitized Solar Cells (DSSC), Perovskite Solar Cells, and Transparent Thin-Film Silicon Solar Cells. It discusses their integration into diverse applications, such as building-integrated photovoltaics, consumer electronics, the automotive industry, and aerospace. The review identifies challenges, including low efficiency, durability concerns, production costs, and integration hurdles, that currently hinder their widespread adoption. Moreover, the paper emphasizes the transformative potential of transparent solar panels in shaping the future of renewable energy, not only as energy generators but also as aesthetically pleasing and multifunctional components of our built environment. Finally, the paper underscores the need for continued research and development efforts to enhance efficiency, improve stability, and address integration challenges, paving the way for transparent solar panels to play a central role in the transition toward a more sustainable and energy-efficient future.

Advanced coatings are essential to modern technologies, as they optimise surface characteristics for different application scenarios. Transparent and self-cleaning coatings are increasingly used as protective coatings for various applications, such as foldable touchscreens, windows, and solar panels. Moreover, incorporating other functionalities such as high hardness, wear resistance, and flexibility into transparent and self-cleaning coatings is important for broadening the use cases. Although many kinds of multifunctional coatings have been developed, it is still difficult to embody several properties in one coating adequately, as some properties, such as hardness and flexibility, are inherently contrastive. This review first describes basic principles, including wetting ability, photocatalytic reactions, photo-induced hydrophilic phenomena, and the implication of self-cleaning. The desired properties of multifunctional coatings are then listed, and methods for evaluating different properties are used. Recent progress in various preparation methods for multifunctional coatings, including the sol-gel, dip/spin, and chemical vapour deposition (CVD) methods, are also presented. Magnetron sputtering (MS) technology is widely used in coating preparation. Compared with chemosynthesis and CVD, MS is time-saving, suitable for industrial production, and environmentally friendly. Coatings prepared by MS usually possess excellent mechanical properties. Thus, we highlight the current research status of MS technology in multifunctional coating preparation. Moreover, according to the multilayer design structure of coatings, their optical and mechanical properties and self-cleaning ability can be controlled by combining the characteristics of different materials. Finally, combining photocatalytic materials such as TiO2 with other materials through a multilayer structure to obtain a multifunctional coating with excellent overall properties is discussed.

There has been a surge in the interest for (semi)transparent photovoltaics (sTPVs) in recent years, since the more traditional, opaque, devices are not ideally suited for a variety of innovative appli-cations spanning from smart and self-powered windows for buildings to those for vehicle inte-gration. Additional requirements for these photovoltaic applications are a high conversion effi-ciency (despite the necessary compromise to achieve a degree of transparency) and an aesthetical-ly pleasing design. One potential realm to explore in the attempt to meet such challenges is the bio-logical world, where evolution has led to highly efficient and fascinating light-management structures. In this mini-review, we explore some of the biomimetic approaches that can be used to improve both transparent and semitransparent photovoltaic cells, such as moth-eye inspired structures for improved performance and stability or tuneable, coloured, and semi-transparent devices inspired by beetles’ cuticles. Lastly, we will briefly discuss possible future developments for bio-inspired and potentially bio-compatible sTPVs.

Pathogenicity is unknown for the majority of human gene variants. For prioritization of sequenced somatic and germline mutation variants, in silico approaches can be utilized. In this study, 84 million non-synonymous Single Nucleotide Variants (SNVs) in the human coding genome were annotated using consensus Variant Effect Prediction (cVEP) method. An algorithm, implemented as a stacked ensemble of supervised learners, performed combination of the 39 functional, conservation mutation impact scores from dbNSFP4.0. Adding gene indispensability score, accounting for differences in the pathogenicities of the variants in the essential and the mutation-tolerant genes, improved the predictions. For each SNV the consensus combination gives either a continuous-value pathogenicity score, or a categorical score in five classes: pathogenic, likely pathogenic, uncertain significance, likely benign, benign. The provided class database is aimed for direct use in clinical practice. The trained prediction models were 5-fold cross-validated on the evidence-based categorical annotations from the ClinVar database. The rankings of the scores based on their ability to predict pathogenicity were obtained. A two-step strategy using the rankings, scores and class annotations is suggested for filtering and prioritization of the human exome mutations in clinical and biological applications of NGS technology.

In this study, various diamine monomers were used to synthesize aramid polymer films via a low-temperature solution condensation reaction with diacid chloride. For diamines with relatively high basicity, the reaction system became opaque because amine salt formation inhibited polymer synthesis. Meanwhile, low-basicity diamines with strong electron-withdrawing groups, such as CF3 and sulfone, were smoothly polymerized without amine salt formation to provide highly viscous solutions. The acid byproduct HCl generated during polymerization was removed by adding propylene oxide to the reaction vessel and converting the acid into highly volatile inert substances. The resulting solutions were used as varnishes without any additional purification, and polymer films with an excellent appearance were easily obtained through a conventional casting and convection drying process. The films neither tore nor broke when pulled or bent by hand; furthermore, even when heated up to 400°C, they did not decompose or melt. Moreover, polymers prepared from 2,2-bis (trifluoromethyl) benzidine (TFMB) and bis (4-aminophenyl) sulfone (pAPS) did not exhibit glass transition until decomposition. The prepared polymer films showed a high elastic modulus of more than 4.1 GPa and a high tensile strength of more than 52 MPa. In particular, TFMB-, pAPS-, and 2,2-bis (4-aminophenyl) hexafluoropropane-based polymer films were colorless and transparent, with very high light transmittances of 95%, 96%, and 91%, respectively, at 420 nm and low yellow indexes of 2.4, 1.9, and 4.3, respectively.

Marine clay deposits are commonly found worldwide. Considering the cost of dumping and the related environmental concerns, an alternative solution involving the reuse of soils that have poor conditions is crucial. In this research, the authors examined the durability of marine deposited clays and compiled a corresponding database. The use of slag alone as a binder, at any percentage, increased the accumulated mass loss (ALM) up to 2%. However, the use of lime as the third binder seemed to accelerate the chemical reactions associated with the hydration of clay and cementitious material and to enhance the chemical stability, i.e., samples that included both lime and slag experienced the same ALM as samples treated with cement only. Scanning electron microscopy analysis confirmed the durability improvements of these clays. The proposed unconfined compressive strength and accumulated mass loss relationship yielded practical approximation for the fine- and coarse-grained soils blended with up to three binders until 60 days of curing.

Palpation is a simple but effective method to differentiate tumors from healthy tissues. Development of miniaturized tactile sensors embedded on endoscopic or robotic devices are the key toward precise palpation diagnosis and the subsequent timely treatment. This paper reports on the fabrication and characterization of a novel tactile sensor with mechanical flexibility and optical transparency that can be easily mounted on soft surgical endoscopes and robotics. Utilizing the pneumatic sensing mechanism, the sensor offers a high sensitivity of 1.25 mbar and negligible hysteresis, enabling the detection of phantom tissues with different stiffnesses ranging from 0 to 2.5 MPa. Our configuration combining pneumatic sensing and hydraulic actuating also eliminates electrical wiring from the functional elements located at the robot end-effector, thereby enhancing the system safety. The optical transparency path in the sensors together with its mechanical sensing capability open interesting possibility in early detection of solid tumor as well as in the development of all in-one soft surgical robots that can perform visual/mechanical feedback and optical therapy.

Building envelope can play a crucial role in building improvement efficiency and the adoption of Phase Change Materials (PCMs) coupled with transparent elements may (i) allow a better control of the heat flows from/to the outdoor environment, (ii) increase the exploitation of solar energy at building scale and (iii) modulate the light transmission to avoid glare effects. Starting from a literature review of experimental works, this research identifies the main possible integration of PCM in transparent/translucent building envelope components (in glazing, in shutters and in multilayer façade system) drawing a global picture potentials and limitations of these technologies. Transparent envelopes with PCMs have been classified from the simplest “zero” technology, which integrates the PCM into the double glass unit (DGU), to more complex solutions – with different numbers of cavities of the glass (TGU), different position of PCM layer (internal/external shutter), and in combination with other materials (TIM, aerogel, prismatic solar reflector, PCM curtain controlled by an electric pump). The results of the analysis are resumed in a SWOT (strengths, weakness, opportunities and threats) analysis table to underline strengths and weaknesses of transparent building envelope components with PCMs, and to indicate opportunities and threats for future research and building application.

Intramedullary fixation with elastic stable intramedullary nailing and stabilization with an external fixator are standard methods for the treatment of diaphyseal femoral shaft fractures in children. A retrospective bi-centre cohort study was carried out, including all patients between the ages of 2 and 16 years with isolated traumatic diaphyseal femur fractures, treated either with intramedullary nailing or an external fixator. In total, 57 patients (17 female and 40 male) with a mean age of 6.5 ± 2.7 years (min. 2; max. 16 years) with a mean follow-up period of 6.1 ± 4.6 months (min. 2; max. 26 months), were included in this retrospective study. 33 patients were treated with elastic stable intramedullary nailing and 24 patients, and external fixation. In total, 18 patients (32%) experienced osteosynthesis-related complications: 8 patients (24%) in the elastic stable intramedullary nailing group and 10 (42%) in the external fixation group, leading to revision surgery in 10 patients (18%). At the latest follow-up, all fractures were radiologically healed with no evidence of malangulation or malrotation (defined as >20°) and full weight-bearing. There was a lower rate of complications in the ESIN group than in the external fixation group. Overall, we were unable to show a significant difference between the two methods.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

Lithium-ion batteries (LIBs) have become indispensable energy storage devices for various applications, ranging from portable electronics to electric vehicles and renewable energy systems. The performance and reliability of LIBs depend on several key components, including the electrodes, separators, and electrolytes. Among these, the choice of binder materials for the electrodes plays a critical role in determining the overall performance and durability of LIBs. This review introduces polymer binders that have been traditionally used in the cathode, anode, and separator materials of LIBs. Furthermore, it explores the problems identified in traditional polymer binders and examines the research trends in next-generation polymer binder materials for lithium-ion battery as alternatives.

This work opens a new pathway to fabricate high dimensional stability Invar36 aerospace devices with Binder Jetting technology, for applications where temperature fluctuations directly interfere in the correct performance of high sensibility systems. Since full density part fabrication is one of the main ongoing challenges for Binder Jetting, the leading objective of this work is to study and optimise the main process parameters to increase the final density of Invar36 printed parts. Microstructural analysis and obtained density and CTE values, confirmed the feasibility to fabricate Invar36 parts.

A printed Vivaldi antenna that is optically transparent, ultra-wideband (UWB), and reconfigurable has been developed, fabricated, and tested at millimeter wave frequencies. It covers a broad frequency range of 20-30 GHz by using three PIN diodes. The diodes control the current flow to direct the beam of the antenna. The results of numerical simulations and measurements match at millimeter wave frequencies. The design of this antenna is unique as it allows for a reduction in size and ease of integration while also providing the ability to change the radiation pattern by up to 300 degrees, making it suitable for 5G and 6G communications. Additionally, this antenna can also be useful for RF applications that require dynamic switching of radiation patterns and cognitive radio.

In this study we mimic the unique, transparent protective carapace (shell) of myodocopid ostracods, through which their compound eyes see, to demonstrate that the carapace ultrastructure also provides functions of strength and protection for a relatively thin structure. The bulk ultrastructure of the transparent window in the carapace of the relatively large, pelagic cypridinid (Myodocopida) Macrocypridina castanea was mimicked using thin film deposition of dielectric materials to create a transparent, 15 bi-layer material. This biomimetic material was subjected to the natural forces withstood by the ostracod carapace in situ, including scratching by captured prey and strikes by water-borne particles. The biomimetic material was then tested in terms of its extrinsic (hardness value) and intrinsic (elastic modulus) response to indentation along with its scratch resistance. The performance of the biomimetic material was compared with that of a commonly used, anti-scratch resistant lens and polycarbonate that is typically used in the field of transparent armoury. The biomimetic material showed the best scratch resistant performance, and significantly greater hardness and elastic modulus values. The ability of biomimetic material to revert back to its original form (post loading), along with its scratch resistant qualities, offers potential for a biomimetic eye protection coating that could enhance material currently in use.

This study presents a new bionanocomposite coating on poly(ethylene terephthalate) (PET) made of pullulan and synthetic mica. Mica nanolayers have a very high aspect ratio (α) at levels much greater than that of conventional exfoliated clay layers (e.g., montmorillonite). A very small amount of mica (0.02 wt%, which is ϕ ≈ 0.00008) in pullulan coatings dramatically improved the oxygen barrier performance of the nanocomposite films under dry conditions, whereas this performance was partly lost as the environmental relative humidity (RH) increased. This outcome was explained in terms of the perturbation of the spatial ordering of mica sheets within the main pullulan phase because of RH fluctuations, as confirmed by modelling of the experimental OTR data according to Cussler’s model. The presence of the synthetic nanobuilding block (NBB) led to a decrease in both static and kinetic coefficients of friction compared with neat PET (≈12% and 23%, respectively) and PET coated with unloaded pullulan (≈ 26% reduction in both coefficients). In spite of the presence of the filler, all of the coating formulations did not significantly impair the overall optical properties of the final material, which exhibited haze values below 3% and transmittance above 85%, with the only exception represented by the formulation with the highest loading of mica (1.5 wt%, which is ϕ ≈ 0.01). These findings revealed, for the first time, the potential of the NBB mica to produce nanocomposite coatings in combination with biopolymers for the generation of new functional features, such as transparent high oxygen barrier materials.

The paper covers the development of formulations and technology for low energy building materials based on the alkaline alumino-silicate binder and appropriate for special purposes. The microstructure of the binder was investigated using scanning electron microscopy and atomic force microscopy. The identification of the phase compositions was done by means of X-ray diffraction. By leach rate measurement and chemical analysis of pore liquid, the linkage of the alkali metal ions in water-insoluble composites was researched. The dependence of structure formation on mix design and curing conditions was investigated. Specific examples of manufacture and application of binder-based glues and adhesives have been considered, incl. ones for low-temperature insulating composite materials, heat insulation perlite-based materials, heat insulation of industrial boilers, and the fire resistant heat insulating system. The advantages of the binder-based temperature insulating composites compared to traditionally used ones are shown.

Concrete is the most commonly used construction material due to its various advantages, such as versatility, familiarity, strength and durability and it will continue to be in demand far into the future. However, with today’s sensitivity to the environmental protection, this material is facing unprecedented challenges due to its high greenhouse gas emission mainly during cement production. This paper investigates one of the promising cement replacement materials, alkali activated cement (AAC) concrete. Being produced mainly from byproduct materials and having a comparable structural performance to conventional concrete, AAC concrete has a potential to transform the construction industry. Mechanical properties such as compressive and flexural strength and the relationship between them are studied. Different source materials such as fly ash (FA), ground granulated blast furnace slag (GGBS), silica fume (SF) and Metakaolin (MK) are used. The effect of the source materials and the activator solutions on the concrete performance is studied. Furthermore, the freeze-thaw resistance of the concrete is studied. The results of the study showed that the behavior of AAC depends highly on the source material combinations as well as type used. The effect of the alkaline solution is also dependent on the source material used. Mixes with higher GGBS content in general showed the highest strength while mixes with MK showed the highest flexural strength. The results from the freeze-thaw test showed that proper design of AAC concrete with a lower water content is critical to achieve a good resistance.

Flue gas desulfurization gypsum (FGD gypsum) is obtained from the desulphurization of combustion gases in fossil fuel power plants. FGD gypsum can be used to produce anhydrite binder. The effect of three independent variables such as the calcination temperature of FGD gypsum (500-800 oC), the hydration time (3-28 days) and the amount of activator (0-2 %) on the compressive strength of anhydrite binder were studied. K2SO4 and Na2SO4 were used as activators. The compressive strength of anhydrite binder was evaluated using a full factorial design. The multiple linear regression models were developed to correlate the significant variables to the compressive strength of anhydrite binder. The experimental results and statistical analysis showed that the hydration time had the biggest impact on the compressive strength of anhydrite binder using K2SO4 and Na2SO4. K2SO4 made a greater influence on the compressive strength than Na2SO4. The results of modeling indicated that the individual variables had a larger effect on the compressive strength of anhydrite binder than their interaction. The mean absolute percentage error between experimental and calculated values of compressive strength was less than 10 %.

Artificial Intelligence (AI) has seen increased application and widespread adoption over the past decade despite, at times, offering a limited understanding of its inner working. AI algorithms are, in large part, built on weights, and these weights are calculated as a result of large matrix multiplications. Computationally intensive processes are typically harder to interpret. Explainable Artificial Intelligence (XAI) aims to solve this black box approach through the use of various techniques and tools. In this study, XAI techniques are applied to chronic wound classification. The proposed model classifies chronic wounds through the use of transfer learning and fully connected layers. Classified chronic wound images serve as input to the XAI model for an explanation. Interpretable results can help shed new perspectives to clinicians during the diagnostic phase. The proposed method successfully provides chronic wound classification and its associated explanation. This hybrid approach is shown to aid with the interpretation and understanding of AI decision-making processes.

The microfluidic industry recognizes the lack of sensitive and standardized testing methods as one of the major hurdles to overcome before fulfilling its revolutionary promises. Highly ranked upon the list of things in need of testing methods are the internal dimensions of microfluidic structures after chip assembly. This work, performed under the MFMET project, aims to address this challenge by presenting and comparing multiple protocols for measuring the dimensions of internal microfluidic channels of fully assembled transparent chips. The protocols include optical profilometry, optical microscopy and tiled digital imagery. Several standardized chip designs out of two different materials commonly used in microfluidics (D263©bio and TOPAS© COC) were measured by the different protocols. A consistency analysis through normalized error statistics revealed optical profilometry as the preferred method due to its low uncertainty compared to the other protocols and its higher consistency with nominal geometry values. All protocols showed difficulty with vertical depth measurements of internal structures. Associated possible directions of future research are considered including further study of the influence of multiple refractive surfaces on optical profilometry measurements and further investigation of confocal microscopy as a potential measurement method showing promising preliminary results. The influence of the different materials appears to be minimal on optical profilometry, but other materials and method would merit looking into before such an observation might be generalized. In conclusion, the results of this work directly address the current lack of measurement methods for internal microfluidic structures by providing a comprehensive comparison of different protocols, ultimately suggesting a preferred option for immediate application within the microfluidic industry. Additionally, this work offers valuable directions for future research, serving as an initial step in overcoming a significant challenge that impedes the microfluidic industry from realizing its revolutionary potential.

Transparent electrodes (TEs) made of metallic nanowires, such as Ag, Au, Cu, and Ni, have attracted rising attention for several reasons: 1) they can act as a substitute for tin oxide-based TEs such as indium-tin oxide (ITO) and fluorine-doped tin oxide (FTO); 2) various methods exist for fabricating such TEs such as filtration, spraying and meyer bar coating; 3) greater compatibility with different substrates can be achieved due to the variety of fabrication methods; and 4) extra functions in addition to serving as electrodes, such as catalytic abilities, can be obtained due to the metals that compose the TEs. There are a large number of applications for TEs, ranging from electronics and sensors to biomedical devices. This short review is a summary of recent progress, mainly during the past five years, on silver nanowire-based TEs. The focus of the review will be on theory development, mechanical, chemical and thermal stability and optical properties. The many applications of TEs are outside the scope of this review.

Understanding the equilibrium saturation level is crucial to Binder Jetting (BJ). Saturation level influences dimensional accuracy, print time, green strength, and final material properties. Improved understanding of the saturation level can reduce development time for new materials and improve existing processes in BJ. Attempts have been made to predict saturation levels of parts with simple calculations from droplet primitives and capillary pressure. There is, however, limited experimental validation for these methods and they do not include the impact of drop velocity and droplet spacing. This study incorporates the influences of drop velocity and droplet spacing on the saturation level of the part. Drop primitives of varying droplet velocity and droplet spacing were compared. Results show that velocity impacts the feasible parameter space.

The global focus on geopolymer binder production has increased due to the adoption of waste materials and industrial byproducts. Given the gradual decline of the availability of fly ash and ground granular blast furnace slag (GGBFS) resulting from the decarbonization process in electricity and steel productions, waste clay brick powder (WCBP), could be a viable substitute of these pozzolanic by-products. This research is dedicated to thoroughly investigate the techno-eco-efficiency performance of WCBP when utilized as a geopolymer precursor. The favorable mechanical characteristics exhibited by fly ash-GGBFS-WCBP-based geopolymer binder emphasize the importance of assessing its sustainability alongside its technical viability. The study employed life cycle analysis (LCA), following ISO 14040-44 standards, and using the Simapro software, to evaluate the environmental implications of the use of WCBP-based geopolymer mixtures. Human toxicity emerged as the primary impact. Moreover, the analysis of life cycle costs highlighted key financial factors, with around 65-70% attributed to alkaline activators of the total cost. The production of alkaline activators was identified as a critical point for both environmental impact and economic considerations due to energy consumption. While WCBP-rich samples exhibit a 1.7-0.7% higher environmental impact compared to the control mix (CM), their high mechanical strength and cost-effectiveness make them technologically and economically efficient geopolymer mixes. In conclusion, the portfolio analysis for techno-eco-efficiency affirms that mixes containing 40%, 30%, and 20% WCBP are more efficient than those using 10% and 0% WCBP, respectively.

The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.

Laser-induced functionalisation using excimer laser irradiation has been widely applied to transparent conductive oxide films. However, exploring suitable irradiation conditions is time-consuming and cost-ineffective as there are numerous routine film fabrication and analytical processes. Thus, we herein explored a real-time technique to monitor the laser-induced functionalisation of transparent conductive oxide films. We developed two types of monitoring apparatus, electrical and optical, and applied them to magnetron-sputtered Sn-doped In2O3 films grown on glass substrates and hydrogen-doped In2O3 films on glass or plastic substrates using a picosecond Nd:YAG pulsed laser. Both techniques could monitor the functionalisation from a change in properties of the films on glass substrates by laser irradiation, but electrical measurement was unsuitable for plastic samples because of a laser-induced degradation of the underlying plastic substrate, which harmed proper electrical contact. Instead, we demonstrated that the optical properties in the near-infrared region were suitable for the monitoring and the changes in the optical properties were visually detected in real-time by using a near-infrared camera.

Generating localized haptic feedback on touch displays has been a challenge in recent years. In this study, we introduce a haptic interface using transparent thin-film PVDF actuators to address this issue. The transparency feature allows for mounting the actuators at any location beneath the display, enabling localized haptic feedback as the generated vibration is primarily evident on the mounting area. Two different configurations are designed, simulated and prepared to explore the effectiveness of the proposed approach. The first configuration is used to characterize the haptic interface. Modal and forced-vibration analysis are performed to identify important design characteristics based on human factor considerations. Subsequent 2AFC psychophysics experiments validate the characteristics. In the second configuration, eight actuators are attached to the touch surface in a 2x4 matrix formation and excited at different voltage amplitudes. Human experiments are conducted based on the results from corresponding forced-vibration analysis. The results show that subjects demonstrate an accuracy of 96% in identifying locations with haptic feedback when the actuators are excited with 232 Vpp. Overall, our study demonstrates the effectiveness of the haptic interface equipped with PVDF-type actuators in achieving localized haptic feedback on touch displays.

Contemporary architects and the construction industry are trying to cope with increasing requirements concerning energy efficiency and environmental impact. One of the available options is the active utilization of energy gains from the environment, specifically solar energy gains. These gains can be utilized by, for example, solar walls and facades. The solar façade concept has been under development for more than a century. However, it hasn’t achieved widespread use for various reasons. Rather recently the concept was enhanced by the application of transparent insulation materials that have the potential to increase the efficiency of such façades. The presented study evaluates the environmental efficiency of 10 solar façade assemblies in the mild climate of the Czech Republic, Central Europe. The evaluated façade assemblies combine the principles of a solar wall with transparent insulation based on honeycomb and polycarbonate panels. The study applies Life-Cycle Assessment methodology to the calculation of environmental impacts related to the life cycle of the evaluated assemblies. The results indicate that even though there are several limiting factors, façade assemblies with transparent insulation have lower environmental impacts compared to a reference assembly with standard thermal insulation. The highest achieved difference is approx. 84% (in favour of the assembly with transparent insulation) during a modelled 50-year façade assembly service life.

Asphalt binder requires more investigation to be accurately and precisely extracted since it is a significant procedure for quality control quality assurance (QC/QA) and subsequent binder characterization. In this research, the authors provided a hands-on experience with binder extraction to deliver recommendations concerning the sensitive steps that may affect the outcomes (extracted binder content, P_be%). Based on the extraction by the centrifuge method, two mineral matter determination methods (ashing and centrifuge) were addressed. Field cores were investigated with comparing the P_be% to the actual binder content, P_ba%. Analysis of variance (ANOVA) and Tukey Post-Hoc statistical analyses, in addition to linear least square regression analysis, were used to show the significance of difference according to 38 variant cores randomly obtained from the field segments (in-service roads) via the first two weeks from the construction date. Such cores involved reclaimed asphalt pavement (RAP), reclaimed asphalt shingles (RAS), and a wide range of additives. The two extraction methods were compared with concluding that the centrifuge method was highly recommended based on a quantitative evaluation, which delivered the same average P_ba% based on the 38 cores. Furthermore, the centrifuge method provided much saving in the experimental time (almost half the time required for the ashing method). It was found that the ashing outcomes were equal to the centrifuge outcomes with disregarding the ammonium carbonate addition. Thus, it could be recommended to reassess the ammonium carbonate addition as it might excessively compensate for fake minerals that have not been lost by the ignition oven.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

The utilisation of the industrial residual products to create new value-added materials and to reduce footprint is a modern challenge of science and industry. Development of the new multifunctional and bio-based composites is an excellent opportunity for complex utilisation of industrial residual products. The study describes the preparation and characterisation of the three-phases bio-based composites. The main components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash the cenosphere (CS). Three-phase composite prepared in the form of a block for investigation of the mechanical properties and density and a form of granules for determination of the water and oil products sorption was investigated. This work investigated the dependence of the properties on the main component DCR and CS fraction. Is found, that maximum compression strength (in block form) observed for composition without CS and DCR addition - 79.3 MPa, the second highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt% compression strength is in range 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

Dye sensitized solar cell technology is having an important role in renewable energy research due to its features and low cost manufacturing processes. Devices based on this technology appear very well suited for integration into glazing systems due to their characteristics of transparency, color tuning and manufacturing directly on glass substrates. Field data of thermal and electrical characteristics of dye sensitized solar modules (DSM) are important since they can be used as input of building simulation models for the evaluation of their energy saving potential when integrated into buildings. However still few works in the literature provide this information. The study here presented wants to contribute to fill this gap providing a thermal and electrical characterization of a DSM in real operating conditions using a method developed in house. This method uses experimental data coming from test boxes exposed outdoor and dynamic simulation to provide thermal transmittance and solar heat gain coefficient (SHGC) of a DSM prototype. The device exhibits an U-value of 3.6 W/m²K, confirmed by an additional measurement carried on in the lab using a heat flux meter, and a SHGC of 0.2, value compliant with literature results. Electrical characterization evidences an increase of module power with respect to temperature causing DSM suitable for integration in building facades.

Metal oxide based electrodes play a crucial role in various as a transparent conductive oxide (TCO). One of the metal oxides, nickel oxide is a promising electrical conductive material. Here, we display that incorporation of vanadium in NiO lattice significantly improve both electrical conductivity and hole extraction. Also, vanadium doped nickel oxide exhibits a lower crystalline size compared to pristine nickel oxide, which maintains the reduction of surface roughness. These results indicating that the vanadium is an excellent dopant for NiO.

Asphalt cement will not last for a long time as the world encounters a diminishment in the crude oil. For sustainable, flexible pavement development, new resources can provide a contribution to replace it partially or entirely. In this study, asphalt was partially and entirely replaced by guayule resin as a bioresource by-product, extracted during the guayule natural rubber production. Crumb rubber modifier (CRM) was used as an asphalt enhancer. The Superpave grading system was followed at high, intermediate, and low temperatures to evaluate such innovative binder for rutting, fatigue, and thermal cracking, respectively, in addition to viscosity. Therefore, the original, short-term aging and long-term aging were simulated using tank, rolling thin film oven, and pressure aging vessel materials. Additionally, component analysis using Fourier-transform infrared spectroscopy was provided to link the rheological properties with the chemical changes. Outcomes showed a relatively much lower viscosity of guayule in the same high-temperature asphalt grade indicating savings in plant energy consumption and reduced environmental emissions. CRM enhanced guayule, but not as much as asphalt, proven by polymeric component migration through liquid binder. This enhancement was reflected in the rheological performance besides other factors. As-received guayule seems to have high oxygen content proven by strong absorption peak intensities of oxidative bonds (e.g., Carbonyl and sulfoxide). Such pre-oxidation was negatively reflected in the intermediate- and low-temperature performance of guayule and guayule-based binders. However, the investigated guayule had potential to compensate for asphalt replacement in the presence of CRM by 23–42% by weight of blend.

In the past decade, considerable efforts have been devoted to the development of semitransparent organic solar cells. Numerous materials and architectures have been proposed for the future commercialization of these devices. Among these, the use of ternary active layers demonstrated a great promise for the development of efficient semi-transparent organic solar cells with the potential for future applications including self-powered greenhouses and powered windows. Researchers seek alternative solutions to the trade-off between device power conversion efficiency (PCE) and average visible transmittance (AVT), with photoactive materials being the key parameters that govern both (PCE) and (AVT) as well as device stability. Several new organic materials, including polymers and small molecules, were synthesized, and used in conjunction with a variety of techniques to achieve semitransparent conditions. In this review paper, we will look at the working principle and key parameters of semi-transparent organic solar cells, as well as the methods that have been used to improve the performance of ternary-based semi-transparent organic solar cells. The main approaches were concluded to be spectral enhancement and transparency increment of the active layer through bandgap tuning, utilizing novel organic semiconductors, and design architecture of the active layers.

NDBs were fabricated from gum arabic (GA) and polyvinyl alcohol (PVA) in different ratios using novel techniques (casting, dehydration, and peeling). The GA/PVA blends were cast with a novel vibration-free horizontal flow (VFHF) technique, producing membranes free of air bubble defects with a homogenous texture, smooth surface, and constant thickness. The casting process was achieved on a self-electrostatic template (SET) made of poly-(methyl methacrylate), which made peeling the final product membranes easy due to its non-stick behavior. After settling of the cast membranous blind, sheets were dried using nanometric dehydration under a mild vacuum stream using a novel stratified nanodehydrator (SND) loaded with P2O5. After drying the TBM, the dry, smooth membranes were peeled easily without scratching defects. The physicochemical properties of the NDBs were investigated using FTIR, XRD, TGA, DTA, and AFM to ensure that the novel techniques did not distort the product quality. The NDBs retained their virgin characteristics, namely, their chemical functional groups (FTIR results), crystallinity index (XRD data), thermal stability (TGA and DTA), and ultrastructural features (surface roughness and permeability), as well as their microbial biodegradation ability. Comparing the two TBM’ s precursors, PVA had a higher crystallinity index (CI), more mass loss at higher temperatures, greater thermal stability due to higher heat resistance, and a higher clearance of surface roughness due to its large particle size (PS), as well as its higher permeability parameters, namely pore diameter (PD) and void volume (VV), than those for GA. Accordingly, increasing the PVA allocation in the bioplastic blends can enhance their properties except for mass loss, whereby increasing the GA allocation in the TBM blend reduces its mass loss at an elevated temperature. In addition, there is no statistical difference between the NDBs and ordinary air-dried NDBs in PS, PD, and VV, indicating that the novel procedures used did not distort their parent properties examined, as well as their ability for biodegradation. In comparison to control samples, the separated bacteria and fungus destroyed the NDBs. Pseudomonas spp. and Bacillus spp. were the two main strains of isolated bacteria, and Rhizobus spp. was the main fungus. The nanodehydration method gave the best solution for the prompt drying of water-based biopolymers free of manufacturing defects, with simple and easily acquired machinery required for the casting and peeling tasks, in addition to its wonderful biodegradation behavior when buried in wetted soil.

Organophilic nano clay is the composition of mostly clay and organic molecules designed to improve various materials' physical and chemical properties. Permanent deformation in asphalt pavements is primarily the result of inadequate compaction, excessive loading, and high temperatures. Rutting can result in aquaplaning, leading to accidents and costly maintenance and rehabilitation works that drain the economy. Such behavior of asphalt pavements may be attributable to poor selection of aggregate, asphalt binder, or substandard asphalt binders. This study used different percentages of organophilic nano clay ranging from 3.0% - 5.0% with two penetration grade bitumen, i.e., N.R.L 60-70 & N.R.L 80-100. Adding organophilic nano clay to asphalt binder significantly reduced the rutting potential under cyclic loading at high temperatures (55 °C). Ten modified formulations and two virgin bitumen specimens were prepared. The modified binders' viscosity and rutting were tested using the Rotational Viscometer and Wheel Tracker Test (W.T.T.), respectively. The results were analyzed using software for Statistical Analysis. It was recorded that organophilic nano clay-modified bitumen significantly affected rutting to interpret the results. The results indicated that rutting decreased and viscosity increased in all nano clay-modified bitumen samples, with a 4.5% O.N.C modified binder showing the most significant improvement.

Benign design of alkali-activated slag/FA geopolymer paste has intriguing increasing attention for optimizing its service performance. Therefore, the replacement of fly ash (FA) with 10 wt% silica fume (SF) is investigated by mechanical strength after freeze-thawing cycles and microstructure characterization. The results show that an appropriate dosage (30 wt%) of slag is necessary to attain alkali-activated slag/FA geopolymer paste with excellent mechanical performance, and the SF/slag/FA (SF: slag: FA= 10:30:60, wt%) geopolymer paste exerts the compressive and flexural strength of 95.2 and 3.2 MPa, respectively. Meanwhile, the doped 10 wt% SF facilitates the propagation of (N, C)-A–S–H chains, rather than the formation of C-S-H gels, evidenced by the absent exothermic peak at about 861oC from the differential scanning calorimetry (DSC) curves, leading to the increases in the pores volume with a pore diameter<20 nm and tortuosity by mercury intrusion porosimeter (MIP) results, corresponding to an improved freezing-thawing resistance with the residual compressive strength of 52.8 MPa and the weight loss of 10.5% after 300 freeze-thawing cycles. It explores a cost-effective and benign facile approach to designing heating curing-free alkali-activated slag/FA geopolymer paste with good freezing-thawing resistance.

Existing rammed earth construction methods have disadvantages such as increased initial costs for manufacturing the large formwork and increased labor costs owing to the labor-intensive construction techniques involved. To address the limitations of existing rammed earth construction methods, an autonomous rammed earth construction method is introduced herein. As this autonomous rammed earth construction method uses a modular formwork, alternative materials must be used in the construction to satisfy the requirements for the early-age binder performance. Accordingly, this study evaluates the use of an epoxy emulsion composed of epoxy and a hardener to enhance the performance of the binder. Preliminary experiments were conducted to determine the optimal formulation of the epoxy emulsion, following which the compressive strength, water loosening, shrinkage, rate of mass change, and microstructure of several red clay binder specimens with and without epoxy emulsion were analyzed at early ages. The results confirmed that the epoxy emulsion can be applied to satisfy the performance requirements for autonomous rammed earth construction by improving the durability and strength of the binder at early ages.

Binder jet printed components typically have low overall density in the green state and high shrinkage and deformation after heat treatment. It has previously been demonstrated that, by including nanoparticles of the same material in the binder, these properties can be improved as the nanoparticles can fill the interstices and pore throats between the bed particles. The beneficial effects from using these additive binder particles can be improved by maximising the binder particle size, enabling the space within the powder bed to be filled with a higher packing efficiency. The selection of maximum particle size for a binder requires detailed knowledge of the pores and pore throats between the powder bed particles. In this paper, a raindrop model is developed to determine the critical radius at which binder particles can pass between pores and penetrate the bed. The model is validated against helium pycnometry measurements and binder particle drop tests. It is found that the critical radius can be predicted, with acceptable accuracy, using a linear function of the mean and standard deviation of the particle radii. Percolation theory concepts have been employed in order to generalise the results for powder beds that have different mean particle sizes and size distributions. The results of this work can be employed to inform the selection of particle sizes required for binder formulations, to optimise density and reduce shrinkage in printed binder jet components.

Nearly Zero Energy Buildings (NZEBs) play a key role in the world energy transition and this is motivating the scientific community to develop innovative electrical and thermal systems, characterized by very high efficiency to specifically address the energy needs of modern buildings. Naturally, the integration on buildings of latest generation PV-systems helps to satisfy this need and, having in mind this objective, an innovative and highly efficient BIPV-system is presented and discussed in this paper. First, the proposed PV-system is purpose-built to be fully integrated into a variety of buildings and, preferably, into their rooftop. It is based on a certain number of innovative rotating and bifacial PV-modules which are specifically made to be installed “under-glass”, within a likewise custom-made transparent casing. Each of the aforementioned PV-module has the form of single row of bifacial PV-cells and is equipped with two special terminations; the PV-modules are then installed inside their transparent casing, side by side and suitably spaced from each other. Thanks to the aforementioned properties, the PV-modules can rotate around their central longitudinal axis, by using a very low-power, reliable and efficient mono-axial solar tracking system. Finally, by the aforementioned way, the proposed PV-system assumes – de facto - the form of a transparent BIPV-generator (PV-skylight), equipped with an innovative “under-glass” single axis solar tracking system. Once the proposed PV-generator is fully integrated into a building, it generates electricity and, additionally, helps to improve both the whole energy performances and the aesthetic appearance of the building. The electricity generation and illuminance performances of the proposed BIPV-generator are experimentally tested by using a low-power home-made prototype driven by different solar tracking logics and under different operating conditions; the most relevant results are summarized and extensively discussed.

Transparent conductive electrodes (TCEs) are of enormous significance to the emergence of flexible and wearable electronics and continued growth of modern devices. Versatile and tunable TCEs, featuring with not only high optical transmittance but also intriguing features of electrochemical energy-storage capability, remain a significant challenge. Here we develop capacitive active films comprised of graphene-conjugated V2O5@poly (3,4-ethylene dioxythiophene) ternary composite (V2O5@PEDOT/rGO) on silver nanowire coated substrates as solid-state super/pseudocapacitors. The constructed electrodes exhibit improved electrolyte ions interaction with effective graphene layer, achieving high areal capacitance 0.6-1.2 mF.cm−2 with 0.5M LiCl electrolytes at optical transparency >60% with record durability. As demonstrated, the kinetic blocking of PEDOT layer and anchoring capability of graphene upon amphoteric soluble vanadium ions from layered V2O5 nanoribbons/nanobelts contribute synergistically to the unusual electrochemical stability, also shown using scanning electrochemical microscopy (SECM) providing electroactivity sites and ion transportation rates. As-fabricated symmetric solid-state supercapacitors delivered broad potential window >1.4 V under two different electrolyte environments (aqueous LiCl and LiCl/PVA gel) and demonstrated higher power and energy density (0.27 μWh.cm−2) outperforming previously reported devices at <0.1 μWh.cm−2. The electrochemical properties are also discussed in terms of solvation in polymer gel electrolyte ions.

The electrical and optical properties of sol-gel derived aluminum-doped0 zinc oxide thin films containing 2 at.% Al were investigated considering the modifying effects of 1) increasing the sol H₂O content; and 2) thermal treatment procedure with high-temperature approach followed by an additional heat-treatment step under a reducing atmosphere. According to the results obtained via the TG-DTA analysis, FT-IR spectroscopy, X-ray diffraction technique and four-point probe resistivity measurement, it is argued that the sol hydrolysis, decomposition of the deposited gel and crystallization of grains result in grains of larger crystallite size and stronger c-axis preferred orientation with slightly less microstrain in the modified sample. The consequent morphology and grain-boundary characteristics turn out as improved conductivity, implying higher values of concentration and mobility of charge carriers. A detailed investigation on samples optical properties, in terms of analyzing their absorption and dispersion behaviors through the UV-Vis-NIR spectroscopy, support our reasoning for the increase of the mobility, and to a lesser extent, the concentration of charge carriers, while causing only a slight degradation of optical transmission. Hence, an enhanced performance as a transparent conducting film is claimed for the modified sample by comparing the figure-of-merit values.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

We demonstrated an ITO-free, highly transparent organic solar cell with the potential to be integrated into window panes for energy harvesting purposes. A transparent, conductive ZnO/Ag/ZnO multilayer electrode and a Ag:Ca thin film electrode were used in this transparent device as the bottom and top electrode, respectively. To further improve the transmittance of the solar cell, the thickness of the top ZnO layer was investigated by both experiment and simulation. An average visible transmittance of > 60% was reached, with a maximum transmittance of 73% at 556 nm. Both top and bottom illumination of the solar cell generated comparable power conversion efficiencies, which indicates the wide application of this solar cell structure. In addition, we fabricated distributed Bragg reflector mirrors with sputtered SiO2 and TiO2, which efficiently increased the power conversion efficiency over 20% for the solar cells on glass and PET substrates,

Asphalt binder is a temperature sensitive material, whose performance is greatly affected by the climate change of the environment. Improper selection of asphalt will cause a lot of damage and affect the durability of the road. The establishment of asphalt pavement performance zoning in Xinjiang, a vast area with great temperature difference, will provide reference for the selection of asphalt suitability, the refinement of pavement design and the sustainable development of road engineering. In this study, 11 years of temperature data in Xinjiang region were collected and analyzed, and 98% reliability of pavement design temperature was used to draw a performance grading map of asphalt pavement in Xinjiang region based on ArcGIS platform. Finally, Xinjiang region was divided into 9 performance zones. At the same time, the performance grade (PG) of five kinds of asphalt binders in Karamay were explored. The result shows that there is little difference in continuous PG span between different matrix asphalt binders, the lower penetration grade, the better high temperature performance, the worse low temperature performance. After adding SBS modifier, the continuous PG span can be higher than the matrix asphalt in 20 ℃. All these provide the basis for reasonable selection of asphalt binders in different areas of Xinjiang.

This paper presents a proof-of-concept study on the biocolonization of 3D-printed hydroxyapatite scaffolds with mesenchymal stem cells (MSCs). Three-dimensional (3D) printed biomimetic bone structure made of Calcium Deficient HydroxyApatite (CDHA) intended as future bone graft was made from newly developed composite material for FDM printing. The biopolymer polyvinyl alcohol serves in this material as a thermoplastic binder for 3D molding of the printed object with a passive function and is completely removed during sintering. The study presents the material, the process of fused deposition modeling (FDM) of CDHA scaffolds and its post-processing at three temperatures (1200, 1300, 1400 °C), as well it evaluates the cytotoxicity and biocompatibility of scaffolds with MTT and LDH release assays after 14 days. The study also includes a morphological evaluation of the cellular colonization with scanning electron microscopy (SEM) in two different filament orientations (rectilinear and gyroid). The results of the MTT assay showed that the tested material was not toxic, and cells were preserved in both orientations, with most cells present on the material fired at 1300°C. Results of the LDH release assay showed a slight increase in LDH leakage from all samples. Visual evaluation of SEM confirmed the ideal post-processing temperature of the 3D-printed FDM framework for samples fired at 1300°C and 1400°C, with a porosity of 0.3 mm between filaments. In conclusion, the presented fabrication and colonization of CDHA scaffolds have great potential to be used in the tissue engineering of bones.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

This research seeks to interpret the component analysis of an innovative bio-asphalt binder using guayule resin in addition to crumb rubber modifier (CRM) at high concentrations. Such asphalt modification aims to minimize the dependency on virgin asphalt binder and provide new solutions concerning sustainable, flexible pavement industry. Guayule resin is a promising bioresource for asphalt binder replacement. By now, it could be considered a no value byproduct extracted during the guayule natural rubber production. CRM is a recycled material derived from scrap tires. The provided interpretation could help in understanding the asphalt-rubber-guayule interaction mechanism. Fourier transform infrared spectroscopy (FTIR), supported by thermo-gravimetric analysis (TGA), was used to investigate the component analyses of guayule resin composition, asphalt guayule interaction, and asphalt rubber guayule interaction, compared to corresponding asphalt rubber interaction. Additionally, the rheological properties at elevated temperatures were provided to link the microscale properties with the final product performance. The study clarified the distinct carbon and hydrogen compositional elements of guayule resin. Asphalt and guayule resin have similarities in chemical composition and rheological behavior with temperature susceptibility. The asphalt guayule binder had physical interaction. However, when both interacted with rubber, a chemical interaction was attributed, with no difference in rubber dissolution tendency, in asphalt rubber guayule, compared to asphalt rubber. A bio-binder composed of 62.5% asphalt, 25% guayule and 12.5% CRM had the potential to provide rheological properties better than base asphalt. Such behavior was interpreted by a high release of rubber components.

Waste biogenic materials from seafood exploitation are valuable resources of new compounds exploitation within the blue bioeconomy concept. Here, we describe the effectiveness of Raman technology implementation as an in-line tool for demineralization process control of crustaceans or gastropods. We produced transparent chitin polymer foils from three waste crustacean shells (C. sapidus, S. mantis and M. squinado) using a slow, green chemical approach employing acetic acid, and showed the progressive process of biogenic carbonate dissolution and increasing the Raman characteristic signal of chitin, in a time dependence manner. It turned that chitin foils obtaining is species-specific, and the demineralization bath of waste shell mixture can be effectively tracked by Raman spectroscopy, for solvent control and the recovery of the calcium acetate as valuable by-product. Comparatively, calcium acetate drug, a compound widely used in kidney failure diseases, or as additive in nutraceuticals and food industry, has been obtained here, following a green demineralization path of the sea snail Rapana venosa intact shell, assisted by Raman tech-nology, using 9% acetic acid (vinegar) solution for 14 days. To validate the final products identity and quality, The process of waste shells demineralization and the final products of the treatment were investigated using various Raman techniques and technologies, cross-validating the results with FT-IR, XRD and SEM-EDX techniques. NIR Raman spectroscopy revealed chitin bands in a time-dependent manner, while Resonance Raman spectroscopy showed the preservation of ca-rotenoids after two weeks of acetic acid treatment. A hand-held flexible TacticID Raman system with a 1064 nm excitation demonstrated its effectiveness as a rapid, in-line decision making tool during process control and revealed excellent reproducibility of the lab-based instrument signal, suitable for in situ evaluation of the demineralization status and solvent saturation control. The calcium acetate recovered from residual treatment solutions was assessed regarding its hydration status, purity, and suitability as recrystallized material for further use as pharmaceutical product or ingredient in complex formulations.

We report on the study of energy-harvesting performance in medium-size (400 cm²) glass-based semitransparent solar concentrators employing edge-mounted photovoltaic modules. Systems using several different types of glazing system architecture and containing embedded diffractive structures are prepared and characterized. The technological approaches to the rapid manufacture of large-area diffractive elements suitable for use in solar window-type concentrators are described. These elements enable the internal deflection and partial trapping of light inside glass-based concentrator windows. We focus on uncovering the potential of pattern-transfer polymer-based soft lithography for enabling both the improved photon collection probability at solar cell surfaces, and the up-scaling of semitransparent solar window dimensions. Results of photovoltaic characterization of several solar concentrators employing different internal glazing-system structure and diffractive elements produced using different technologies are reported and discussed.

Producing complex shaped tungsten carbide cobalt (WC-Co) tools by classical technologies is difficult and often impossible due to their high hardness and brittle fracture behavior. Additive Manufacturing (AM) is a suitable technology for creating complex structures and simultaneously shortening expensive machining processes. Binder Jetting (BJ) is an innovative AM technology that offers several advantages over laser-based processes, for example low manufacturing costs and high build-up rates. Binders with nanoparticle additives have already proven to be effective in in- creasing the packing density of the powder bed and improving the sintering properties. Addition- ally, they offer the possibility of selectively changing the material composition in the part. This paper presents a concept for the use of nanoparticles to generate gradients in the green compact, which leads to a cobalt gradient in the part after sintering. The possibility of introducing particles locally into complex structures allows local modification of the material properties.

Traditional metals such as stainless steel, titanium and cobalt chrome are used in biomedical applications (implants, scaffolds etc.) but suffer from issues such as osseointegration and compatibility with existing bone. One way to improve traditional biomaterials is to incorporate ceramics with these metals so that their mechanical properties can be similar to cortical bones. Tricalcium phosphate is such a ceramic with properties so that it can be used in human body. This research explores the use of binder jetting based additive manufacturing process to create a novel biocomposite made of cobalt chrome and tricalcium phosphate. Experiments were conducted and processing parameters were varied to study their effect on the printing of this biocomposite. Layer thickness, binder saturation and drying time affected the dimensional tolerance and the density of the green samples. This effect is important to understand so that the material can be optimized for use in specific applications.

One of the main benefits of binder jetting is the ability to print quickly compared to other metal additive manufacturing methods. Demand for higher throughput continues to increase, but the effects of faster print speeds on part outcomes are not yet clearly understood. MIM powders are used to achieve optimal density and surface finish. Printing at slower speeds results in densities near 98% and average surface roughness values as low as 4 μm (Ra), in the as-sintered condition. In this study, spread speeds were varied in order to understand the effect of print speed on surface roughness. 316L D90 -22 μm powder was used to print with 3 different spread speeds, 2 different layer thicknesses, and 2 different printhead droplet sizes. The surface finish and density were quantified for the sintered parts that were oriented at 0, 22.5, and 45 degrees with respect to the Z- direction.

Vaccine hesitancy substantially impacts global vaccination rates. During the COVID-19 pandem-ic in Germany, vaccination uptake exhibited considerable regional disparities. To assess the fac-tors contributing to this variation, we examined the influence of sociodemographic variables on COVID-19, COVID-19 booster, and influenza vaccinations within a cohort of 37,078 participants from 13 German federal states in the digital health cohort study, DigiHero. Our findings re-vealed variations in vaccination rates based on sociodemographic factors. However, these fac-tors had limited explanatory power regarding regional differences in vaccine uptake. In contrast, we found substantial correlations between regional support of specific parties during last local elections and the vaccination uptake at Landkreis-level. In conclusion, sociodemographic factors alone did not suffice to explain the regional disparities in vaccine uptake. Political stances can play a major role, but the current investigation did not assess the individual political orienta-tion, but used only ecological approach.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

The consumption of fiber in the human diet is a global recommendation to ensure a healthy diet. Quinoa (Chenopodium quinoa Willd.), a gluten-free grain, and chia (Salvia hispanica), a seed, contain high fiber content and both have the potential to be explored in the development of nutraceutical and pharmaceutical formulations. An interesting characteristic of chia is its ability to form viscous mucilage when in contact with water, bringing the prospect of a binder in solid formulations. To produce tablets with a high fiber content, it is more appropriate to transform the material into granules using a wet process, with the help of a tool that exploits this possibility. Therefore, the objective of the present work was to study, using the Mixer Torque Rheometer, the feasibility of using chia as a binder to produce granulated quinoa and the development of chewable tablets. To this end, an experimental design was carried out to evaluate the impact of variables on the rheometer results for subsequent granulation. It was possible to obtain the granulation point for the formulations and after producing the granules, physical tests were carried out in which we noticed improvements in the flow. In the end, a formulation was selected for the development of chewable tablets containing quinoa and chia fibers.

The polymer binder, poly(imide-co-siloxane) (PIS), was synthesized and applied to form a thin cathode layer composites for a thermal battery that has an unusually high operating temperature of 450 °C. The PIS was prepared through cross-linking of the polyimide with polysiloxane. The morphology of FeS₂/PIS composites showed that FeS₂ particles was coated with the PIS cross-linked gel. The FeS₂/PIS composites enabled to fabricate mechanically stable thin cathode layer that was 20–10% of the thickness of a conventional pellet-type cathode. The FeS₂/PIS composites were stable up to 400 °C and maintained their morphology at this temperature. PIS coating layers decomposed at 450 °C and a new residue was generated, which was observed by transmission electron microscopy and the compositional change was analyzed. The FeS₂/PIS composites showed enhanced thermal stability over that of FeS₂ in thermogravimetric analysis. The thermal battery with the PIS polymer binder showed a 20% discharge capacity increase when compared to a conventional pellet-type cathode.

The snATAC + snRNA platform allows epigenomic profiling of open chromatin and gene expression with single-cell resolution. The most critical assay step is to isolate high-quality nuclei to proceed with droplet-base single nuclei isolation and barcoding. With the increasing popularity of multiomic profiling in various fields, there is a need for optimized and reliable nuclei isolation methods, mainly for human tissue samples. Herein we compared different nuclei isolation methods for cell suspensions, such as peripheral blood mononuclear cells (PBMC, n=18) and a solid tumor type, ovarian cancer (OC) (n=18), derived from debulking surgery. Nuclei morphology and sequencing output parameters were used to evaluate the quality of preparation. Our results show that NP-40 detergent-based nuclei isolation yields better sequencing results than collagenase tissue dissociation for OC, significantly impacting cell identification and analysis. Given the utility of applying such techniques to frozen samples, we also tested frozen preparation and digestion (n=6). A paired comparison between frozen and fresh samples validated the quality of both specimens. Finally, we demonstrate the reproducibility of scRNA and snATAC + snRNA platform, by comparing the gene expression profiling of PBMC. Our results highlight how the choice of nuclei isolation methods is critical for obtaining quality data in multiomic assays. It also shows that the measurement of expression between scRNA and snRNA is comparable and effective for cell type identification.

Background: We aimed to evaluate the effect of early pelvic binder use in emergency management of suspected pelvic trauma, compared with the conventional stepwise approach. Methods: We enrolled trauma patients with initial stabilization using a pelvic binder for suspecting pelvic injury. Inclusion criteria were traumatic injury requiring a trauma team and at least one of the following: loss of consciousness or Glasgow coma score (GCS) < 13; systolic blood pressure < 90 mmHg; falling from ≥6 m; injury to multiple vital organs; and suspected pelvic injury. Various parameters, including gender, age, mechanism of injury, GCS, mortality, hospital stay, initial vital sign, revised trauma score, injury severity score, and outcome, were assessed and compared with historical controls. Results: A total of 204 patients with high-energy multiple-trauma from single level I trauma center in North Taiwan were enrolled in the study from August 2013 to July 2014. The two group baseline patient characteristics were all collected and compared. The trauma patients with suspected pelvic fractures initially stabilized with a pelvic binder had shorter hospital and ICU stays. The study group achieved statistically significantly improved survival and lower mean blood transfusion volume and mortality rate although they were more severe in the trauma score. Conclusions: We recommend prompt pelvic binder use for suspected pelvic injury before definitive imaging is available, as a cervical spine collar is used to protect the cervical spine from further injury prior to definitive identification and characterization of an injury.

8-Hydroxydeoxyguanosine (8-OHdG) was the most widely used oxidative stress biomarker of the free radical-induced oxidative damage product of DNA, which may allow a premature assessment of various diseases. This paper designed a label-free, portable biosensor device to direct detect 8-OHdG by plasma coupled electrochemistry on transparent and conductive indium tin oxide (ITO) electrode. We reported a flexible printed ITO electrode made from particle-free silver and carbon inks. After inkjet printing, the working electrode was sequentially assembled by gold nanotriangles (AuNTAs) and platinum nanoparticles (PtNPs). This nanomaterial-modified portable biosensor showed excellent electrochemical performance for 8-OHdG detection from 10 μg/mL to 100 μg/mL by our self-developed constant voltage source integrated circuit system. This work demonstrated a portable biosensor for simultaneously integrating nanostructure, electroconductivity, and biocompatibility to construct advanced biosensors for oxidative damage biomarkers. The proposed nanomaterial modified ITO-based electrochemical portable device was a potential biosensor to approach 8-OHdG point-of-care testing (POCT) in various biological fluid samples, such as saliva and urine samples.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.

We developed a novel machine learning (ML) algorithm with the goal of producing transparent models (i.e. understandable-by-humans) while also flexibly accounting for nonlinearity and interactions. Our method is based on ranked sparsity, and allows for flexibility and user-control in varying the shade of the opacity of black-box machine learning methods. The main tenet of ranked sparsity is that an algorithm should be more skeptical of higher-order polynomials and interactions \textit{a~priori} compared to main effects, and hence the inclusion of these more complex terms should require a higher level of evidence. In this work, we put our new ranked sparsity algorithm (as implemented in the open-source R package, `sparseR`) to the test in a predictive model "bakeoff" (i.e. a benchmarking study of ML algorithms applied "out-of-the-box," that is, with no special tuning). Algorithms were trained on a diverse set of simulated and real-world data sets from the Penn Machine Learning Benchmarks database, addressing both regression and binary classification problems. We evaluate the extent to which our human-centered algorithm can attain predictive accuracy that rivals popular black-box approaches such as neural networks, random forests, and support vector machines, while also producing more interpretable models. Using out-of-bag error as a meta-outcome, we describe the properties of data sets in which human-centered approaches can perform as well as or better than black-box approaches. We find that interpretable approaches predicted optimally or within 5% of the optimal method in most real-world data sets. We provide a more in-depth comparison of the performances of random forests to interpretable methods for several case studies, including exemplars in which algorithms performed similarly, and several cases when interpretable methods underperformed. This work provides a strong rationale for including human-centered transparent algorithms such as ours in predictive modeling applications.

For the first time, an environmentally friendly waste-free closed cycle for the formation of EMI shielding materials that are promising for 5G communications is considered. Based on the proposed closed technological cycle, two types of EMI shielding materials have been obtained; both materials have significant prospects for signal shielding in all ranges that are allocated in different countries for 5G communication. The first type of materials are transparent conductive meshes with a transparency of more than 80% and with a shielding efficiency of more than 40 dB in the S and L bands and about 30 dB in the K and Ka bands. The study of signal reflection characteristics in the S, L, C, K and Ka bands showed the promise of using these materials as transparent 5G signal reflectors. The reflection coefficient in all considered ranges is above 90% (-0.5 dB). The second type of shielding material are continuous silver micro caps films characterized by a shielding efficiency of 90.1 dB at a thickness of 6.2±1.2 µm. We have also shown that silver micro caps can separate into silver flakes and ribbons when sonicated. These materials can also be used to produce EMI shielding coatings and composites. A detailed analysis of the shielding properties showed that each type of materials obtained in a closed technological cycle is comparable with the best literature results and significantly wins in terms of cost.

We developed a transparent and flexible electrochemical sensor using a platform based on a network of single-walled carbon nanotubes (SWCNTs) for the non-enzymatic detection of hydrogen peroxide (H2O2) released from living cells. We decorated the SWCNT network on a poly(ethylene terephthalate) (PET) substrate with platinum nanoparticles (PtNPs) using a potentiodynamic method. The PtNP/SWCNT/PET sensor synergized the advantages of a flexible PET substrate, a conducting SWCNT network, and a catalytic PtNP, and demonstrated good biocompatibility and flexibility, enabling cell adhesion. The PtNP/SWCNT/PET-based sensor demonstrated enhanced electrocatalytic activity towards H2O2 as well as excellent selectivity, stability, and reproducibility. The sensor exhibited a wide dynamic range of 500 nM to 1 M, with a low detection limit of 228 nM. In addition, Furthermore, the PtNP/SWCNT/PET sensor remained operationally stable even after bending at various angles (15°, 30°, 60°, and 90°) with no noticeable loss of current signal. These outstanding characteristics enabled the PtNP/SWCNT/PET sensor to be practically applied for the direct culture of HeLa cells and the real-time monitoring of H2O2 release by the HeLa cells under drug stimulation.

Emulsion stabilisation of base layers surfaced with chip seals often proves problematic with chips punching into the base and early distress. This can be aggravated by the use of modified binders that restricts the evaporation of moisture from pavement layers. The introduction of New-age (Nano) Modified Emulsion (NME) stabilisation has the advantage that water is chemically repelled from the stabilised layer resulting in an accelerated development of strength. A need was identified to evaluate the early life performance of selected chip seals, together with identified binders. Three different chip seal surfacings with unconventional modified binders were constructed and evaluated using Accelerated Pavement Testing (APT) with the MMLS3. The objectives of the experimental design and testing were to evaluate binder performance, early loss of chips before chip orientation at low temperatures, punching of the chips into the NME stabilised base, deformation characteristics of a Cape seal and the effect of the use of a standard normal modified binder. This paper contains details of the NME base layer, the binder and seal selection and the test results. It is shown that a cost-effective thin chip seal in combination with a suitable binder can be used on a NME stabilised base with confidence.

Background: Early diagnosis of postoperative complications is an urgent task, allowing timely prescribing of appropriate therapy and reducing the cost of patient treatment. Prognostic models based on various data could help in the early diagnosis of postoperative complications after cardiac surgery. Objectives: The purpose of the study was to determine whether an integrated approach based on clinical data along with metabolites and biomarkers had greater predictive value than the models built on less data. Methods: The study included patients (n=62) admitted for planned cardiac surgery (coronary artery bypass grafting with cardiopulmonary bypass), who were retrospectively divided into two groups depending on the presence (n=26) or absence (n=36) of postoperative complications of all types. Clinical and laboratory data on the first day after surgery were analyzed. Additionally, patients' blood samples were collected before and on the first day after surgery to determine biomarkers (interleukin-6, procalcitonin, NT-proBNP, high-sensitivity troponin T) and metabolites (8 aromatic and 2 dicarboxylic acids were detected using gas chromatography-mass spectrometry). Results: Patients before surgery, compared with healthy donors, differed in the concentration of metabolites (p &lt; 0.05), and had concentrations of a number of biomarkers exceeding the corresponding reference values. Multivariate PLS-DA models, predicting the presence or absence of postoperative complications, were built using clinical data (ROC-AUC=0.71), concentrations of metabolites and biomarkers (ROC-AUC=0.60), and the entire data set (ROC-AUC=0.75). For comparison we built univariate models using the EuroScore2 (ROC-AUC=0.59) and SOFA (ROC-AUC=0.76) scales; concentrations of lactate (ROC-AUC=0.71), the dynamic changes of 4-hydroxyphenyllactic acid (ROC-AUC=0.69), and the sum of three sepsis-associated metabolites (ROC-AUC=0.70). The proposed complex model using entire data set was comparable to the SOFA scale, which confirms the expediency of searching for new predictive models based on a variety of factors.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

The aim of this retrospective study was to compare the clinical outcomes of treating isolated surgical neck fractures of the humerus using either the intramedullary nail or the MIROS (Minimally Invasive Reduction and Osteosynthesis System®) system. The study included 42 patients who underwent surgical treatment at the Polyclinic from January 2014 to June 2020. The results indicated that both treatments were effective; however, the MIROS system exhibited a higher complication rate. Intramedullary nailing was more reliable, thus recommended as the primary treatment method. This study underscores the importance of selecting the appropriate fixation technique to minimize complications and enhance patient outcomes.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

Excess nitrogen in agricultural drainage poses a serious threat to the water quality safety of the Yellow River basin. Utilizing aquatic plants to modify the rhizosphere microbial community structure and facilitate nitrogen transformation is a crucial strategy for mitigating regional water eutrophication. Our results revealed that the denitrification rate (DR), dissimilatory nitrate reduction to ammonium rate (DNRAR) and nitrogen fixation rate (NFR) of rhizosphere sediments exhibited a significant increase in artificially cultivated ditch. Compared with those in natural ditches, the richness of the bacterial community and the relative abundances of Bacteroidota, Verrucomicrobiota, Firmicutes, Anaeromyxobacter and Geobacter, which are involved mainly in the nitrogen cycle, in the rhizosphere sediments of artificially cultivated ditch were significantly greater due to improvements in environmental conditions. In artificially cultivated ditch, the dominant functional genes affecting DRNARs in the rhizosphere sediments of P. australis were nrfC and nrfA, while DRs were driven mainly by norB and napA, which were influenced by the nitrogen and carbon levels; and the dominant functional genes affecting NFRs in the rhizosphere sediments of T. orientalis were nifD, nifK and nifH. Our results provide a scientific basis for the use of aquatic plants for mitigating excess nitrogen levels in agricultural drainage.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

In this paper, we extend the KdVSKR equations in (1+1)-dimension and (2+1)-dimension to fractional KdVSKR equations with modified Riemann-Liouville derivative. The (2+1)-dimensional KdVSKR equation, which is a recent extension of (1+1)-dimensional KdVSKR equation, can model the resonances of solitons in shallow water. By means of the Hirota bilinear method, finite symmetry group method and consistent Riccati expansion method, many new interaction solutions have been derived. Soliton-cnoidal interaction solution of the (1+1)-dimensional fractional KdVSKR equation has been derived for the first time. For the (2+1)-dimensional frac-tional KdVSKR equation, two-wave interaction solutions and three-wave interaction solutions, including dark-soliton-sine interaction solution, bright-soliton-elliptic interaction solution, and lump-hyperbolic-sine interaction solution, have been derived. Impact of the fractional order on the shapes of these solutions has been illustrated by figures. Three-wave interaction solutions of fractional systems have not been reported in the existing references. The research idea in this paper can be applied to other fractional differential equations.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

Antimicrobial peptides represent a promising alternative to traditional drugs in relation to cost, toxicity and, primarily, the growing problem of drug resistance. Here we report on the activity against HSV-1 and HSV-2 of a previously described wide-spectrum synthetic decapeptide, Killer Peptide (KP). As determined by plaque reduction assays, treatment with KP at 100 μg/mL resulted in a reduction in the viral yield titer of 3.5 Logs for HSV-1 and 4.1 Logs for HSV-2. Further evaluation of KP antiviral activity focused on the early stages of virus replicative cycle, including the determination of the residual infectivity of viral suspensions treated with KP. A direct effect of the peptide on viral particles, impairing virus absorption and penetration, was shown. The toxicity profile proved to be extremely good with a selectivity index of 29.6 for HSV-1 and 156 for HSV-2. KP was also active against an acyclovir (ACV)-resistant HSV-1 strain, while HSV-1 subcultures in the presence of sub-inhibitory doses of KP did not lead to the emergence of resistant strains. Finally, the antiviral action of KP proved to be synergistic with that of ACV. Overall, these results demonstrate that KP could represent an interesting addition/alternative to acyclovir for antiviral treatment.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.