It is meaningful to monitor and identify the concrete cracks as they will seriously reduce the fatigue life of pavement. In this paper a new method based on distributed long-gauge optic fiber sensing is proposed to implement the crack identification. Firstly, the damage indicator, namely strain curve envelope area ratio (SCEAR), is proposed and calculated with the measured strain in time series when the plane goes across the pavement where the sensors are installed. Then the indicators with different sensors are normalization by the value of the indicator from one referenced sensor where damage normally will not happen. If the crack happens within the sensing gauge of the sensor, the value of damage indicator SCEAR from the sensor will increase. Therefore, the crack will be identified with the change of the damage indicator. The effect of the proposed method is first verified by some simulations of prefabricated pavement as the cracks can be accurately identified by the proposed method. Moreover, the influence from the aircraft, such as taxiing position, aircraft load and aircraft type, is not obvious enough to mislead the identification results. Lastly the static loading tests were implemented with one small-scale model of prefabricated concrete pavement in the lab. From the experimental results the prefabricated cracks inside the pavement slab can be identified accurately with the proposes method as the parameter SCEAR is increased by about 100% at the crack position, while it is only changed by about 3% at the undamaged position.

Waste cooking oil (WCO) recycled asphalt is facing issues regarding insufficient thermal oxidation stability and aging resistance. In this research, glycerol esterification was adopted to pretreat WCO, and the consequences of this treatment on the aging resistance and thermal stability of WCO were analyzed. The impacts of varying levels of esterification of WCO on the high-temperature, low-temperature performances, fatigue properties, as well as aging resistance of recycled asphalt were investigated. Furthermore, the mechanisms of regeneration and anti-aging of deeply esterified WCO recycled asphalt were revealed by Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC) tests. The results indicated that variations in the physical properties of WCO during the aging process were reduced, and its aging resistance was improved following glycerol esterification therapy. The initial thermal decomposition temperature was increased by approximately 115°C, which resulted in the enhancement of thermal stability significantly. Recycled asphalt obtained from deeply esterified WCO exhibited superior high-temperature, low-temperature performances and fatigue properties. Moreover, the thermal oxidation stability and aging resistance of recycled asphalt with deep-esterified WCO could be promoted by reducing the oxidation and volatilization of light components during the aging process.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Pavement crack detection is one of the key links in highway pavement maintenance management. In the current road crack detection, the network model easily ignores the shallow geometric features of cracks and cannot extract the key feature information of cracks. Aiming at the above problems, an EC-YOLOX network model is proposed. The CFPN is constructed to cross-fuse different scale features to solve the feature scale invariance. In the strengthen feature extraction layer, ECANet is fused to enhance the ability to pay attention to key information. The WEIoU loss function is proposed, which assigns different penalty terms to the target box in the vertical and horizontal directions. In terms of data, geometric distortion constraint correction is performed on the single-point perspective pavement image. The experimental data show that the accuracy of EC-YOLOX on the self-built data set reaches 76.34% [email protected], which is 4.45% higher than that of YOLOX. The loss curve of EC-YOLOX is smoother than that of YOLOX, and the minimum training loss value is 2.136, which is 0.648 lower than the minimum loss value 2.784 of YOLOX. Many experiments have verified the effectiveness of EC-YOLOX in improving the detection effect in pavement crack detection.

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

Conductive hydrogels combine the properties of both hydrogels and electrical conductivity, making them soft, flexible, and biocompatible. These properties enable them to conform to irregular surfaces, stretch and bend without losing their electrical conductivity, and interface with biological systems. Conductive hydrogels can be utilized as conductive traces, electrodes, or as a matrix for flexible electronics. Exciting applications in sensors, tissue engineering and human-machine interaction have been demonstrated worldwide. This review comprehensively covers the progress in this field, focusing on several main aspects: functional materials, performance improvement strategies, and wearable applications in human-related areas. Furthermore, the major approaches and challenges for improving their mechanical properties, conductivity, and long-term stability are systematically summarized.

Fatigue performance and self-repairing activity of asphalt binders are two properties that highly influence the fatigue cracking response of asphalt pavement. There are still numerous gaps of knowledge to fill linked with these two characteristics. For instance, current parameters fail to fully accommodate these two bitumen phenomena. This study aims to propose a new procedure to address this issue utilizing the linear amplitude sweep (LAS) test, LAS with rest period (RP) (LASH) test, and simplified viscoelastic continuum damage (S-VECD) model. This research work used four different types of asphalt binders: neat asphalt (NA), self-healing thermoplastic polyurethane (STPU)-modified bitumen (STPB), self-healing poly (dimethyl siloxane) crosslinked with urea bond (IPA1w)-modified bitumen (IPAB), and styrene–butadiene–styrene (SBS)-modified bitumen (SBSB). Before the testing process, all the materials were subjected to short-term and long-term aging. The new procedure showed a superior capacity to analyze and accommodate all bitumen fatigue performances and self-repairing activities compared to the current method. Another finding proved that asphalt binders with higher self-restoration behavior failed to show better fatigue performance. A breakthrough finding demonstrated that asphalt binder fatigue response augmented when the RP was applied at a higher damage intensity (S) value. STPBs and IPABs reached their highest increments of fatigue response, containing 1.0% of STPU and 0.5% of IPA1w, respectively. Those augmentations were 207.54% and 232.64%, respectively.

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

Residential segregation refers to the phenomenon where people of different socioeconomic backgrounds live in spatially separated areas. It is essential to ensure equitable access to urban amenities for all residents in pursuit of the normative values in urban planning. To achieve this planning goal, the disparity in accessibility to urban amenities needs to be appropriately diagnosed. Private apartments and public rental apartments are representative types of residences where residential segregation is likely to occur in the context of South Korea, since these two types show considerable differences in the education, income, and occupations. The objective of this study is to develop an analysis framework for diagnosing the difference in accessibility to urban amenities between the two residential types, and to empirically demonstrate their utility in the planning process. The empirical analysis conducted on Seoul revealed that not only were there significant local variations in accessibility between the two segregated residential areas, but the overall differences across the entire area were also pronounced. The proposed framework is useful in supporting decision-making processes for locating new public facilities or identifying regional priorities for guiding the placement of private amenities, with the aim of mitigating differences between segregated residential areas.

As the number of Uncrewed Aircraft Systems (UAS) operating in our National Airspace System (NAS) increases, so do UAS operations near or at an airport. The accelerating technology in Advanced Air Mobility (AAM) along with the related business opportunities will only further increase UAS operations at airports. This continued growth in new UAS technologies and applications introduces new hazards and risks to the airport environment. This proliferation of UAS highlights the importance of airports developing a robust Safety Management System (SMS) that includes specific UAS risk mitigations. To date, there is currently little empirical data regarding UAS traffic around airports. Nor is there a system to collect this data at a national level. This study attempted to gain insight into the commercial UAS operations across a broader airport population by surveying the airport manager population here in the United States. Research results found that 62% of airports are experiencing an increase in UAS operations in their surrounding airspace. This increase applies to all airspace classifications, with 67% of airports located in controlled airspace experiencing an increase in UAS operations. However, only 27% of airports have some type of UAS safety plan. Similarly, the increase in adverse UAS events near airports suggests that UAS operators may also lack robust safety plans or an understanding of the risks and regulations associated with operating near airports.

This study investigated the effects of icon familiarity on visual search performance. An equal number of familiar and unfamiliar icons were selected as background icons. These background icons were randomly arranged, and a visual search experiment was conducted to locate the target icon. The results showed no significant difference in the time required to find the target icon, regardless of whether the target icon was familiar or unfamiliar. This finding contrasts with previous studies that have suggested a positive effect of target icon familiarity on visual search performance, indicating that the influence of target icon familiarity may not always be consistent and could depend on the characteristics of the background icons. However, when background icons were grouped based on their familiarity, the time taken to locate the target icon was significantly reduced compared to when the icons were randomly arranged. To understand the underlying mechanism of this effect, participants' gaze fixation times were observed. The results revealed that participants spent more time fixating on areas where the target icon was located, rather than on areas without the target icon, suggesting a more efficient visual search process. Moreover, the shorter the visual search time, the higher the proportion of time spent fixating on the area containing the target icon. Additionally, this study examined the contrast ratio between the color of the background space and the dominant color of the target icon, comparing it with the visual search time. The findings indicated that as the contrast ratio increased, the visual search time decreased.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

As well known, the torque produced by a rotating motor generates an opposite and equal reaction torque in the machine casing that must be transmitted to the base. In many applications, especially when the reaction moment has high values, it is necessary to apply some constructive solutions, which in certain cases are difficult to implement. In this context, the need to reduce the reaction moment from drive motors is a challenging topic, which has not been completely exhausted. In this paper, the authors present an original concept of a device which uses the centrifugal force generated by some equidistantly placed weights on a chain drive, for reducing the reaction torque of the motor used for driving a rotating tool. The proposed system is capable to produce a supplementary torque which can be added to driving moment. Due to this fact, by using this system, the power of the driving motor can be decreased, with the consequence of reducing the reaction moment, that must be absorbed by the base.

Despite the growing adoption of Mobility as a Service (MaaS) in urban transportation systems, standard monitoring methods for evaluating its impact and effectiveness still need to be developed. This study proposes a quantitative state of MaaS analysis based on mobility market indicators and macroeconomic metrics to generate a MaaS Status Index (MSI). The intention is to introduce a standardised quantitative methodology for systematically assessing and comparing the state of MaaS in urban mobility systems. The MSI aims to quantitatively capture the economic, social, technological, and infrastructural conditions relevant to MaaS implementation. The methodology includes four steps: identifying relevant mobility markets, defining mobility market metrics, integrating macroeconomic metrics, and deriving the MSI formula. We apply the MSI methodology to the Austrian mobility market as a case study, demonstrating its practicality in assessing MaaS readiness and highlighting specific challenges and opportunities within the Austrian mobility system. The analysis covers the present (2017-2022) and the projected future (2023-2028). The findings indicate that the proposed MSI is an effective tool for evaluating MaaS implementation readiness.

Electrifying aircraft, a crucial advancement in the aviation industry, aims to cut pollutive emissions and boost energy efficiency. Traditional aircraft depend on fossil fuels, which contribute significantly to greenhouse gas emissions and environmental pollution. Despite progress in electric propulsion and energy storage technologies, challenges such as low energy density and integration issues persist. This paper provides a comprehensive thematic and bibliometric analysis to map the research landscape in aircraft electrification, identifying key research themes, influential contributors, and emerging trends. The study applies natural language processing to unstructured bibliographic data and cross-sectional statistical methods to analyze publications, citations, and keyword distributions across various categories related to aircraft electrification. The findings reveal significant growth in research output, particularly in energy management and multidisciplinary design analysis. Collaborative networks highlight key international partnerships, with the United States and China being key research hubs, while citation metrics highlight the impact of leading researchers and institutions in these countries. This study provides valuable insights for researchers, policymakers, and industry stakeholders, guiding future research directions and collaborations.

By installing FBG sensors on the geogrids, smart geogrids can both reinforce and monitor the stability for geogrid-reinforced slopes. In this paper, a geogrid-reinforced sand slope model test was conducted in the laboratory and fiber Bragg grating (FBG) sensing technology is used to measure the strain distribution of the geogrid. Based on the model test, the performance of the reinforced soil slope is simulated by finite element software Midas-GTS, and the stability of the reinforced soil slope is analyzed by strength reduction method. The relationship between the geogrid strain and safety factor is set up. The results indicate that the measured strain and calculated results agree very well. The geogrid strain measured by FBG sensor can be applied to evaluate the stability of geogrid-reinforced sand slopes.

Integrating advanced air mobility (AAM) into the logistics of high-value electronic commodities can enhance efficiency and promote sustainability. The objective of this study is to optimize the logistics network for high-value electronics by integrating AAM solutions, specifically using heavy-lift cargo drones for middle-mile transport and using the mostly rural and small urban U.S. state of North Dakota as a case study. The analysis utilized geographic information system (GIS) and spatial optimization models to strategically assign underutilized airports as multimodal freight hubs to facilitate the shift from long-haul trucks to middle-mile air transport. Key findings demonstrate that electronics, because of their high value-to-weight ratio, are ideally suited for air transport. Comparative analysis shows that transport by drones can reduce the average cost per ton by up to 60% compared to traditional trucking. Optimization results indicate that a small number of strategically placed logistical hubs can reduce average travel distances by more than 13% for last-mile deliveries. Cost analyses demonstrate the viability of drones for middle-mile transport, especially on lower-volume rural routes, highlighting their efficiency and flexibility. The study emphasizes the importance of utilizing existing infrastructure to optimize the logistics network. By replacing truck traffic with drones, AAM can mitigate road congestion, reduce emissions, and extend infrastructure lifespan. These insights have critical implications for supply chain managers, shippers, urban planners, and policymakers, providing a decision support system and a roadmap for integrating AAM into logistics strategies.

This study examines the balancing between urban transportation security and supply chain efficiency amid global disruptions like the COVID-19 pandemic, attacks on maritime lanes, and geopolitical conflicts. The authors combine bibliometric network analysis and natural language processing (NLP) to review scholarly literature from 2017 to 2023. This approach identifies and visualizes evolving thematic trends. Findings reveal a shift towards integrating advanced technologies such as blockchain, AI, and IoT to enhance security without compromising efficiency. This study highlights the significance of integrating urban planning principles and sustainable practices to enhance transportation security and supply chain efficiency within urban environments. Actionable insights for policymakers and supply chain managers emphasize the adoption of integrated, technology-driven security solutions to foster resilient and sustainable supply chains. This research contributes to academic discourse by refining the understanding of evolving priorities in transportation security and supply chain management, offering both theoretical and practical implications for secure and efficient global supply chains.

Millet is a staple food in Northern Nigeria, widely used for the preparation of various millet‐based dishes. However, traditional processing methods, such as de‐husking, can significantly affect the grainʹs nutritional and antioxidant properties. This study evaluates the antioxidant composition and nutritional value of four millet varieties cultivated in Northern Nigeria, with a particular focus on the impact of de‐husking on these parameters. Our analysis encompasses the proximate composition, phytochemical content, antioxidant vitamins, mineral elements, amino acid profile, and antioxidant activities of the millet samples. The findings reveal that all millet varieties contain significant levels of antioxidant compounds, including phenolics, flavonoids, and vitamins, although their concentrations varied due to genetic differences and environmental factors. Notably, in the mineral composition, higher (p<0.05) levels of selenium (Se) and magnesium (Mg) were observed, while trace levels of iron (Fe), copper (Cu), and zinc (Zn) were present. The study demonstrated that de‐husking significantly (p<0.05) reduced the levels of most nutritional and antioxidant parameters, underscoring the superior nutritional value of whole grains compared to their de‐husked counterparts. This highlights the importance of consuming millets in their unprocessed form to maximise health benefits. Moreover, the presence of essential phytochemicals, amino acids, and dietary fiber in these grains, suggests their potential role in reducing the risk of chronic diseases such as cancer, cardiovascular diseases, obesity, and diabetes. These findings underscore the nutritional and functional potential of millet grains as valuable sources of essential nutrients, which can be utilised in nutraceutical formulations or as functional foods for promoting human health. This study emphasises the need to preserve the integrity of millet grains during processing to fully capitalise on their health benefits.

Technological equipment in quarries that extract and deliver aggregates for different uses operates in a predetermined flow depending on the type of rocks exploited and the dimensional characteristics imposed on the final products. In this context, the interruptions in operation required to replace high-wear parts (such as the teeth of excavators and bucket loaders) must be limited as much as possible through technological solutions to increase their service life. The evolution of the wear of the teeth of the quarry equipment that come into direct contact with the rocks was concretely established in the production process, in parallel with the wear values obtained by simulating the wear phenomenon in laboratory conditions, in order to validate the data collected during the operation of the machines. Preventive-repetitive maintenance, within the activities of reconditioning the worn surfaces of the teeth, through the charging process by manual electric welding with covered electrodes, was applied directly to the machine, which led to the shortening of the interruptions in operation necessary to replace these spare parts.

The Fuzzy Transportation Problem (FTP) represents a significant extension of the Classical Transportation Problem (TP) by introducing uncertainly and imprecision into the parameters involved. Various algorithms have been proposed to solve the FTP, including fuzzy linear programming, metaheuristic algorithms and fuzzy mathematical programming techniques combined with Artificial Neural Networks. This paper presents the application of Trigonometric Acceleration Coefficients-PSO (TrigAc-PSO), a variation of the Classical Particle Swarm optimization algorithm, which is an innovative algorithm originally developed for solving the TP. TrigAC-PSO, has demonstrated remarkable success in optimizing various problem domains in crisp environments.

There is a growing need to implement modern technologies, such as digital twinning, to improve the efficiency of transport fleet maintenance processes and maintain the company's operational capacity at the required level. Therefore, the paper reviews the existing literature to present an up-to-date and content-relevant analysis in this field. The proposed methodology is a systematic literature review using the Primo multi-search tool following Preferred Reporting Items for Systematic Reviews and Meta-Analyzes (PRISMA) guidelines. The main inclusion criteria included the publication dates (studies published from 2012–2024) and studies published in English. This resulted in the selection of 201 of the most relevant papers in the area of investigation. Finally, selected articles in this review were categorized into seven groups: a) air transportation, b) railway transportation, c) land transportation (road), d) in-house logistics, e) water and intermodal transportation, f) supply chain operation, and g) other applications. One of the main advantages of the study is that the results are obtained from different scientific sources/databases thanks to using the multi-search tool. Moreover, a bibliometric analysis of the selected papers was performed. The results have led the authors to specify the main research problems and trends related to the analyzed area and to identify the main research gaps for future investigation from academic and engineering perspectives. In addition, based on the review results, a framework for DT in transportation system maintenance was developed. The study ends with conclusions and future research directions.

The chiral optical Tamm state (COTS) is a special localized state at the interface of a handedness-preserving mirror and a structurally chiral medium such as a cholesteric liquid crystal or a chiral sculptured thin film. The spectral behavior of COTS, observed as reflection resonances, is described by the temporal coupled-mode theory. Mode coupling is different for two circular light polarizations because COTS has a helix structure replicating that of the cholesteric. The mode coupling for co-handed circularly polarized light exponentially attenuates with the cholesteric layer thickness since the COTS frequency falls into the stop band. Cross-handed circularly polarized light freely goes through the cholesteric layer and can excite COTS when reflected from the handedness-preserving mirror. The coupling in this case is proportional to anisotropy of the cholesteric and theoretically it is only anisotropy of magnetic permittivity that can ultimately cancel this coupling. These two couplings being equal results in a polarization crossover (the Kopp--Genack effect) for which a linear polarization is optimal to excite COTS. The corresponding cholesteric thickness and scattering matrix for COTS are generally described by simple expressions.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

To address the problems of lining cracking and spalling of tunnel structures in coastal areas under the influence of special geologic conditions, environmental loading, and the coupling effect of chemical erosion effects, hybrid fibers were introduced to fly ash concrete in this study. The working performance, compressive strength, split tensile strength, and flexural strength of the hybrid fiber fly ash concrete were tested.The NEL chloride diffusion coefficient under steady-state conditions and the durability test for resistance to sulfate corrosion were carried out. Thus, in-depth analyses of the comprehensive performance of the hybrid fiber fly ash concrete used for tunnel lining were carried out and the damage mechanism were explored. The results showed that the hybrid fiber fly ash concrete exhibited higher strength compared to the control group concrete. However, when the fibers exceeded a certain dosage, the reduction in the working properties of the concrete structure led to the creation of larger pores in the matrix structure, which in turn affected the mechanical properties of the concrete. The most significant reduction in NEL chloride diffusion coefficient was observed when both steel fibers and coconut fibers were added at 1.0 % volumetric parameter, compared to the control group. The apparent state and compressive strength after sulfate corrosion were also minimally affected. This study ensured that the mechanical properties of the concrete were improved and also substantially improved the corrosion resistance of the matrix, providing a scientific basis for the performance improvement of tunnel lining concrete, confirming that steel-coconut fibers hybrid fiber fly ash concrete has a great potential to improve the structural load bearing capacity and durability, and may provide theoretical support for the continued use of tunneling projects and construction processes.

With the rapid spread of built-in GPS handheld smart devices, the trajectory data from GPS sensors has grown explosively. Trajectory data has spatio-temporal characteristics and rich information. Using trajectory data processing techniques can mine the patterns of human activities and the moving patterns of vehicles in the intelligent transportation systems. A trajectory similarity measure is one of the most important issues in trajectory data mining (clustering, classification, frequent pattern mining, etc.). Unfortunately, the main similarity measure algorithms with the trajectory data have been found to be inaccurate, highly sensitive of sampling methods, and have low robustness for the noise data. To solve the above problems, three distances and their corresponding computation methods are proposed in this paper. The point-segment distance can decrease the sensitivity of the point sampling methods. The prediction distance optimizes the temporal distance with the features of trajectory data. The segment-segment distance introduces the trajectory shape factor into the similarity measurement to improve the accuracy. The three kinds of distance are integrated with the traditional dynamic time warping algorithm (DTW) algorithm to propose a new segment–based dynamic time warping algorithm (SDTW). The experimental results show that the SDTW algorithm can exhibit about 57%, 86%, and 31% better accuracy than the longest common subsequence algorithm (LCSS), and edit distance on real sequence algorithm (EDR) , and DTW, respectively, and that the sensitivity to the noise data is lower than that those algorithms.

Despite various interventions in road safety work, fatal and severe road traffic accidents (RTAs) remain a significant challenge leading to human suffering and economic costs. Understanding the multicausal nature of RTAs, where multiple conditions and factors interact, is crucial for developing effective prevention measures in road safety work. This study investigates the multivariate statistical analysis of co-occurring conditions in RTAs, focusing on single-vehicle accidents with single occupancy and personal injury on Austrian roads outside built-up areas from 2012 to 2019. The aim is to detect recurring combinations of accident-related variables, referred to as blackpatterns (BPs), using the Austrian RTA database. The study proposes Fisher’s exact test to estimate the relationship between an accident-related variable and fatal and severe RTAs (severe casualties). In terms of pattern recognition, the study develops the maximum combination value (MCV) of accident-related variables, a procedure to search through all possible combinations of variables to find the one that has the highest frequency. The accident investigation proceeds with the application of pattern recognition methods, including binomial logistic regression and a newly developed method, the PATTERMAX-method, created to accurately detect and analyse variable-specific BPs in RTA data. Findings indicate significant BPs contributing to severe accidents. The combination of binomial logistic regression and the PATTERMAX-method appears to be a promising approach to investigate severe accidents, providing both insights into detailed variable combinations and their impact on accident severity.

To analyze the impact of weather factors on the resilience of airport flight operations, particularly on flight operation, economic performance, and transportation capacity, Kolmogorov-Arnold Network (KAN) model was used to identify key weather features and establish the mapping relationship between weather factors and airport operational resilience. Taking Xi'an Xianyang International Airport as an example, the weights of each route were determined using the Grey Relational Analysis method considering average daily flight volume, flight distance, and airport flow stability indicators. Flight operation records and weather data were utilized to calculate the importance of key weather factors on the resilience of critical flight operation indicators. The results indicate significant differences in average daily flight volume, flight distance, and airport flow stability across different routes, with routes in economically developed areas having a greater impact on airport flow stability. Temperature and wind speed changes are the key factors affecting flight operation and economic indicators, with importance values of 0.35 and 0.32 respectively. Wind direction change and wind speed change have the greatest impact on flight transportation capacity, with importance values of 0.7 and 0.65 respectively. Therefore, when conducting flight scheduling and risk assessment, special attention should be paid to key weather factors such as temperature and wind speed, while also considering the weight of each route to ensure flight safety, efficiency, and economic benefits.

ABSTRACT After locavore was chosen as “the best word of the year” in 2007, its popularity increased gradually. Today great number of locavores consciously prefer locally produced food for the benefit of themselves and their community. Undoubtedly this conscious movement has its consequences in marketing discipline. Accordingly, this paper is purposed to examine the how locavore perceptions affect loyalty towards retailers that sell locally produced food. In this context, a survey was applied to people residing in Istanbul and Kocaeli districts to measure the robustness of these effects. Furthermore, attitude towards locavore is used as a control variable to reveal to what extend locavorism affects these proposed connections. According to results, for participants with low attitude, Social Responsibility and Health Consciousness variables have significant effect on local retailer shopping loyalty. However, for participants with high attitude, all independent variables proved to have substantial effect on local retailer shopping loyalty. As the first empirical study in Turkey on the subject, this paper will provide important insight to academia and practicioners due to today’s ever-increasing consciousness in green marketing.

In order to help the transportation industry achieve the goal of carbon peak and carbon neutrality, this study is based on the selection of eight variables, such as population size, per ca pita GDP, personal vehicle ownership, passenger and freight turnover, and green space coverage, as the factors influencing the carbon emissions of the transportation industry in Jiangsu Province, and the prediction and analysis of the transportation carbon emission trends from 2000 to 2021, and the prediction and analysis of the carbon emissions of the transportation industry and the time of the peak of the carbon emissions in Jiangsu Province. The trend of transportation carbon emissions from 2000 to 2021 was predicted and analyzed, and the carbon emissions and peak time of carbon emissions in the transportation industry in Jiangsu Province were predicted and analyzed. Comparing the predicted results with other models to verify the accuracy of the results, it was found that the WOA-SVM model had the smallest error among several models. On this basis, targeted measures are proposed to accelerate the process of carbon peak and ensure the smooth achievement of carbon neutrality goals in Jiangsu Province. The results indicate that under the current policy measures, the peak carbon emissions in Jiangsu Province will occur in 2038, with a peak of 48.72 million tons. Jiangsu Province should actively adopt energy-saving and emission-reduction measures, build a green and low-carbon transportation development model, and achieve the carbon peak target ahead of schedule.

The development of the finite element method (FEM) combined block polynomial interpolation with the concepts of finite difference formats and the variation principle. Because of this combination, FEM overcomes the shortcomings of traditional variation methods while maintaining the benefits of current variation methods and the flexibility of the finite difference method. As a result, FEM is an advancement above the traditional variation methods. The aim of the study is to experimentally determine the thermal behavior of two stomatognathic systems, one control and the other presenting orthodontic treatment by means of a fixed metallic orthodontic appliance, both being subjected to several thermal regimes. In order to carry out this experimental study, we examined the case of a female subject, who was diagnosed with Angle class I malocclusion. The patient underwent a bimaxillary CBCT investigation before initiating the orthodontic treatment. A three-dimensional model with fully closed surfaces was obtained by using the InVesalius and Geomagic programs. Like the tissues examined in the patient, bracket and tube-like components, as well as orthodontic wires, can be included to these models. Once it is finished and geometrically accurate, the model is exported to a FEM-using program, such as Ansys Workbench. The intention was to study the behavior of two stomatognathic systems (with and without a fixed metallic orthodontic appliance) subjected to very hot food (70 ⁰C) and very cold food (-18 ⁰C). From the analysis of the obtained data, it was concluded that, following the simulations carried out in the presence of the fixed metallic orthodontic appliance, significantly higher temperatures were generated in the dental pulp.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

In current transportation hubs, it is a common phenomenon that passengers travel with necessary wheeled-luggage or suitcases. Due to the fact that most luggage occupies certain space within dense passenger crowds with giant mass inertia, its abnormal motions, such as drifting, frequently trig unavoidable local disturbances and turbulence in surrounding pedestrian flows, further increasing security risk. While, current researches primarily concentrate on examining the impact of luggage on crowd evacuation efficiency through scenario-based experiments and analyzing the spatial characteristics of crowd distribution in surveillance videos. There still lacks of the dynamic disturbance mechanisms and crowd stability associated with the combined motion of passengers and luggage. Therefore, this study considers the luggage-laden passenger as a deformable particle, the resulting disturbance on surrounding non-luggage passengers is analyzed and quantified into a nonlinear pressure term. Subsequently, the disturbance propagation model of passenger-luggage is developed by adapting the classical Aw-Rascle traffic flow model with incorporation of the pressure term. Simulation experiments of disturbances caused by luggage drifting and retrograding validate that the proposed propagation model aligns with real-world situations in transportation hubs. Quantitively, when luggage-laden passenger drifted left, the disturbing force of left side crowd can reach a peak of 238N in the passenger density of 3.0 p/m2, and the maximum difference between the left and right sides disturbing force can reach 153N. Furthermore, it is recommended that the proposed model can be applied to crowd flow analysis and risk assessment.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Observer-based control is the most commonly used method in the control of electro-hydraulic servo system (EHSS) with uncertainties, but it suffers from the drawback of low accuracy under the influence of large external load forces and disturbances. To address this problem, this paper proposes a novel compensation function observer-based backstepping sliding mode control (BSMC) approach to achieve high-accuracy tracking control. In particular, the model uncertainties, including nonlinearities, parameter perturbations and external disturbances are analyzed and treated together as a lumped disturbance. Then, a fourth-order compensation function observer (CFO) is constructed, which fully utilizes the system state information to accurately estimate the lumped disturbance. On this basis, the estimate of the lumped disturbance is incorporated into the design of an backstepping sliding mode controller, allowing the control system to compensate for the disturbance effect. The stability of the closed-loop control system under the CFO and BSMC is rigorously proven through the use of Lyapunov theory, which guarantees that all the tracking error signals converge exponentially to the origin. Comparative simulations are carried out to show the effectiveness and efficiency of the proposed approach, i.e., compared with PID and ESO-based BSMC methods, the tracking accuracy is improved by 99.93% and 99.76%, respectively.

Abstract. This paper proposes a Second Order Terminal Sliding Mode (2TSM) approach to the trajectory tracking of Differential Drive Mobile Robot (DDMR). Within this cascaded control scheme, the 2TSM dynamic controller, at the inner most loop, tracks the robot’s velocity quantities; while a kinematic controller, at the outer most loop, regulates the robot’s positions. In this manner, chattering is greatly attenuated and finite time convergence is guaranteed by the second order TSM manifold which involves higher order derivatives of the state variables, resulting in inherently robust as well as fast and better tracking precision. The simulation results demonstrate the merit of the proposed control methods.

The rise in population density, vehicle ownership, and urban development has significantly influenced travel demand and altered travel patterns, leading to traffic congestion in rapidly growing urban centers like Accra, Ghana. The traditional approach of expanding roadways to accommodate rising traffic is no longer environmentally sustainable. Instead, emphasis has shifted towards travel demand management (TDM) strategies as a more sustainable solution. This study aimed to investigate a range of TDM strategies that can be adopted in Accra to improve traffic flow through the lenses of everyday road users. The study employed a questionnaire survey and a stratified sampling technique to gather data from 615 respondents for relative importance index (RII) ranking, and Chi-square statistical analysis. The findings reveal that the topmost preferred strategies were mass transit improvements, walking and cycling improvements, and alternative work schedules. Notably, mass transit improvements emerged as the most preferred strategy. The study also unveiled a statistically significant correlation between variables such as age, education level, marital status, income level, and mode of transportation with all selected TDM preferences. However, no significant relationship was found between gender and car ownership with all selected TDM preferences. The study provides valuable insights regarding road users’ preferences for TDM strategies that can aid in planning future urban mobility systems to proactively manage travel demand, alleviate congestion, and promote sustainable transportation options for the city’s residents.

Interferon-gamma (IFN-γ) is an important cytokine in host defense against tuberculosis infection. In some cases, administration of IFN-γ during tuberculosis infection can promote faster cure. In the present work, we have shown that in a mouse model, human interferon-gamma, exhibits some anti-tuberculosis activity, especially in combination with isoniazid.

Based on the nonlinear failure criterion and modified tangential technique, the upper bound solutions of supporting pressure on the deep tunnel face were obtained under pore water pressure conditions. The influence of parameters on the supporting pressure and collapse range was investigated according to the unlimited block failure mechanism. It is found that the upper bound solutions of supporting pressure increase with the growth of the nonlinear coefficient and pore water pressure coefficient. The collapse range of the tunnel face scales out with the increase of the nonlinear coefficient and shrinks when increasing the pore water pressure coefficient. Moreover, with the increase of the nonlinear coefficient, the impact strength on supporting pressure and collapse range declines gradually. According to the calculating results, it is manifest that both the pore water pressure and nonlinear criterion factors have negative impacts on the stability of the tunnel face. Thus, more attention should be paid to these parameters to ensure face stability in deep tunnel construction.

Staphylococcus aureus and Pseudomonas aeruginosa are opportunistic pathogens commonly associated with burn wound infections. These bacteria can form biofilm and contribute a high-level drug resistance to available antibiotics. This study focused on the bacteriolytic activity of phages vB_SAnS_SADP1 and vB_PAnP_PADP4 on 24 h old single or dual-species biofilms of Staphylococcus aureus and Pseudomonas aeruginosa in alone and in combination. Scanning and confocal laser scanning microscopic studies confirmed the structural organization of biofilms in single or dual-species combinations in in-vitro conditions. Single species biofilms are more robust and densely packed at 24 h of incubation. In contrast, dual-species biofilms (0.67± 0.02) are weakly associated due to their inter-species competition and are easily affected by phage cocktails (0.16 ± 0.02). In Invitro conditions, dual-species biofilms were more easily affected by phage cocktail than single phage. Scanning electron microscopic studies revealed the complete diminishment of biofilm formation by four h treatment with single phage or phage cocktails on single species or dual-species biofilms. Confocal laser scanning microscopic images with stains Syto®9 and propidium iodide revealed that phage treatment showed significant uptake of propidium iodide, indicating massive cell death mediated by respective phage or phage cocktail.

The advancement of autonomous driving technology is becoming increasingly vital in the modern technological landscape, promising notable enhancements in safety, efficiency, traffic management, and energy use. Despite these benefits, conventional deep reinforcement learning algorithms often struggle to navigate complex driving environments effectively. To tackle this challenge, we propose a novel network called DynamicNoise, designed to significantly boost algorithmic performance by introducing noise into the Deep Q-Network (DQN) and Double Deep Q-Network (DDQN). Drawing inspiration from the NoiseNet architecture, DynamicNoise uses stochastic perturbations to improve the exploration capabilities of these models, leading to more robust learning outcomes. Our experiments demonstrate a 57.25% improvement in navigation effectiveness within a 2D experimental setting. Moreover, by integrating noise into the action selection and fully connected layers of the Soft Actor-Critic (SAC) model in the more complex 3D CARLA simulation environment, our approach achieved an 18.9% performance gain, substantially surpassing traditional methods. These results confirm that the DynamicNoise network significantly enhances the performance of autonomous driving systems across various simulated environments, regardless of their dimensionality and complexity, by improving their exploration capabilities rather than just their efficiency.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Intelligent Transportation Systems (ITS) are emerging field characterized by complex data model, dynamics and strict time requirements. Ensuring cybersecurity in ITS is a complex task on which the safety and efficiency of transportation depends. The imposition of standards for a comprehensive architecture, as well as specific security standards, is one of the key steps in the evolution of ITS. The article examines the general outlines of the ITS architecture and security issues. The main focus of security approaches is: configuration and initialization of the devices during manufacturing at perception layer; anonymous authentication of nodes in VANET at network layer; defense of fog-based structures at support layer and description and standardization of the complex model of data and metadata and defense of systems, based on AI at application layer. The article oversees some conventional methods as network segmentation and cryptography that should be adapted in order to be applied in ITS cybersecurity. The focus is on innovative approaches that have been trying to find their place in ITS security strategies recently. The list of innovative approaches includes blockchain, bloom filter, fog computing, artificial intelligence, game theory, and ontologies. In conclusion, a correspondence is made between the commented methods, the problems they solve and the architectural layers in which they are applied.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

Metasurface constitutes one of the most promising technologies for holographic imaging; however, the work for terahertz (THz) metasurface holographic imaging is relatively limited. Here, we propose a THz dielectric geometric-propagation phase metasurface, which can operate dual-mode (reflection and transmission) and reconfigurable multifunctional holographic imaging. The dual-mode is realized by controlling the Fermi energy level (Ef) of the graphene integrated into the metasurface unit, and the reconfigurable three-channel holographic imaging in reflection or transmission mode are achieved by switching the feed polarization among left-handed circular polarization (LCP), right-handed circular polarization (RCP) and linear polarization (LP). The metasurface is designed based on the transmission mode, and a physical model for switching to the reflection mode is established. For the first time to the best of our knowledge, a reflection-transmission dynamic modulation THz holographic imaging metasurface has been developed. The holographic metasurface operates in transmission mode at Ef = 0.1 eV, and in reflection mode at Ef = 0.9 eV. Compared with recently published holographic imaging metasurfaces, the proposed metasurface offers the following advantages: high holographic efficiencies (42.5% to 49%), more holographic imaging channels, dynamic modulation dual-mode operations, and reconfigurability.

The part transportation efficiency is a main factor of aircraft sortie generation rate. Part transportation is used to transport spare part from base to carrier. Transportation strategy depends on both demand on carrier and inventory in transportation base. The transportation time and stochastic demand will induce fluctuations of cost and inventory. Thus, a Takagi-Sugeno fuzzy system of dynamic part transportation is established considering transportation time and stochastic demand. And a novel Takagi-Sugeno fuzzy robust control is designed for dynamic part transportation, which will keep transportation cost and part inventory stable. First of all, a fuzzy model with stochastic demand and transportation time is proposed. Then, a novel robust control with cross rule groups is conducted according to production and transportation strategy, which will reduce fluctuations induced by strategies switch. Moreover, robust stability is guaranteed and part can be supplied in time under a low cost. Finally, simulation illustrates usefulness and quickness of the novel Takagi-Sugeno fuzzy robust control. Besides, the proposed method will be useful in other transportation electrification systems with delay time and uncertainty.

Multimodality requires integration of heterogeneous transportation data to construct a broad view of the transportation network. Many new transportation services are emerging with being isolated from previously existing networks. This lead them to publish their data sources to the web -- according to Linked Data Principles -- in order to gain visibility. Our interest is to use these data to construct an extended transportation network that links these new services to existing ones. The main problems we tackle in this article fall in the categories of automatic schema matching and data interlinking. We propose an approach that uses web services as mediators to help in automatically detect geospatial properties and map them between two different schemas. On the other hand, we propose a new interlinking approach that enables user to define rich semantic links between datasets in a flexible and customizable way.

This study critically reviews the situation of Language teachers in China, who transited from on-campus face-to-face teaching to online teaching within one week of the official school opening dates, which were postponed due to the outbreak of the COVID-19 pandemic. Presently, the study is located in an interpretive research paradigm, and hence, it takes the human experiences within educational setups to be subjective and complex. In so doing, to elude this educational transition and its complex dynamics, the research uses such qualitative research methods as document analysis and interviews. Painting a picture of great variety in individual experiences and challenges, strategies, and outcomes not only across these two specific institutions but, certainly, more broadly through the lens of previous case studies. First, it values depth over breadth and tries to unearth the varied experiences, challenges, innovations, and achievements faculty made during their transition into online Language Teaching. The results of the study are believed to be able to contribute quite a rich, detailed, and multi-faceted perspective to the pool of knowledge for the complexities of online Language education in China, which may be of interest to educators, policymakers, and researchers.

The paper addresses the challenging issue of trajectory tracking for uncertain quadrotor UAVs, particularly under the constraints of input saturation and external disturbances. It introduces adaptive laws for managing uncertainties in mass and inertia moments without requiring prior knowledge, ensuring effective control even with varying system parameters. To counteract the effects of input saturation, the study incorporates an auxiliary system designed to compensate for these limitations. Additionally, a disturbance observer(DO) is utilized to manage and mitigate the impact of time-varying external disturbances. The proposed control strategy integrates a sliding mode adaptive control approach with an inner-outer loop structure, enhancing robustness and adaptability. Numerical simulations demonstrate the effectiveness of the designed control strategy.

Under the development mode of deep blending of emerging technologies, major projects are important for enhancing China's comprehensive national strength and independent innovation capability. Based on the social benefits of major projects, and considering the influence of reputation factors, an evolutionary game model composed of a general contractor and subcontractor of major projects is established. This paper studies the influence of various factors including the income distribution coefficient of collaborative innovation, and MATLAB simulation software is analyzed the influence of factors on an evolutionary path. The results show that a reasonable income distribution coefficient can promote the game behavior of both parties to the direction of active collaborative innovation; The reduction of innovation cost and the improvement of spillover technology absorption capacity can make innovation subjects tend to choose active collaborative innovation strategies. In addition, reputation loss above a specific threshold can effectively inhibit free-riding behavior and encourage innovation subjects to choose active collaborative innovation strategies. The research results provide reference for promoting major projects' technology innovation.

We analyze a time-delayed SIQR model that considers the transportation-related infections and entry-exit screening. This model aims to determine the measures for preventing and controlling major emergent infectious diseases and the associated costs. We calculate the basic reproduction number (R0), apply the linearization method, and construct an appropriate Lyapunov function to determine the stability of the disease-free equilibrium in the local and global. We collect COVID-19 infection data from two regions in the United States in 2020 for data fitting, obtain a set of optimal parameter values, and show that the model is suitable for simulating the outbreak and spread of emerging infectious diseases. We find that transportation-related infections increase the basic reproduction number, enhancing the impact on disease spread. Entry-exit screening effectively suppress the spread of disease by reducing the basic reproduction number. Furthermore, we investigate the influence of the incubation period on disease and find that a shorter incubation period results in a shorter duration but a larger scale of infection, and the peaks are reduced. We conduct a sensitivity analysis of the R0 and propose three measures to prevent the spread of new infectious diseases based on the most sensitive parameters: wearing masks, implementing urban closures, and administering medication to sick but not yet hospitalized patients promptly. In the case of COVID-19, we use Pontryagin’s minimum principle to get time-varying control measures to control the spread of the outbreak. Optimal control effectively controls the development and deterioration of the disease. Finally, several control measures are compared through cost-effectiveness analysis, and the results show that wearing masks is the most cost-effective measure. Our study provides some practical guidance for controlling the spread of major emerging infectious diseases.

Road safety and the effectiveness of the transportation system as a whole are significantly impacted by driver comfort. Road surface quality can play a significant part in the driver’s comfort experienced on roads in any country. This study employs a Random Forest technique to examine the association between road roughness and drivers' comfort during long-distance driving. Using Random Forest, a dependable machine learning technique that can handle big datasets and detect nonlinear correlations, this work aims to shed light on the complex dynamics between road conditions and driver’s comfort. 1,048,576 rows of data from MIRANDA, an application developed at the University of Gustave Eiffel, were used in this study as part of the data collected from a probe vehicle. The data collected includes an International Roughness Index (IRI). The IRI thresholds offer a simple method for assessing driver comfort and road irregularity. While highlighting how uneven and uncomfortable the road is, the research's findings (Road Roughness: SD – 0.73; Driver's Comfort: - Mean, 10.01, SD – 0.64) also contribute to the standardization of road condition evaluation and maintenance communication. This finding is anticipated to aid in the development of strategies for improving the welfare of long-haul drivers and fixing road infrastructure to comply with standard road index, ultimately leading to the creation of more efficient and sustainable transportation systems.

As the global demand for clean and sustainable energy sources intensifies, hydrogen emerges as a promising alternative fuel. The widespread adoption of hydrogen, however, is impeded by the lack of efficient systems for storage and transportation. This review aims to summarize the recent advancements and prevailing challenges within the realm of hydrogen storage and transportation, thereby providing guidance and impetus for future research and practical applications in this domain. Through a systematic selection and analysis of the latest literature, this study highlights the strengths, limitations, and technological progress of various hydrogen storage methods, including compressed gaseous hydrogen, cryogenic liquid hydrogen, organic liquids hydrogen, solid materials hydrogen storage, as well as the feasibility, efficiency, and infrastructure requirements of different transportation modes such as pipelines, road and seaborne transportation. The findings reveal that challenges such as low storage density, high costs, and inadequate infrastructure persist despite progress in high-pressure storage and cryogenic liquefaction. The review also underscores the potential of emerging technologies and innovative concepts, including metal-organic frameworks, nanomaterials, and underground storage, along with the potential synergies with renewable energy integration and hydrogen production facilities. In conclusion, interdisciplinary collaboration, policy support, and ongoing research are essential in harnessing hydrogen’s full potential as a clean energy carrier. This review concludes that research in hydrogen storage and transportation is vital to global energy transformation and climate change mitigation.

Over the past couple of decades, Global positioning system (GPS) technology has been utilized to collect large-scale data from travel surveys. As the precise spatiotemporal characteristics of travel could be provided by GPS devices, the issues of traditional travel survey, such as misreporting and non-response, could be addressed. Considering the defects of dedicated GPS devices (e.g., need much money to buy devices, forget to take devices to collect data, limit the simple size because of the number of devices, etc.), and the phenomenon that the smartphone is becoming one of necessities of life, there is a great chance for the smartphone to replace dedicated GPS devices. Although, several general reviews have been done about smartphone-based GPS travel survey in the literature review section in some articles, a systematic review from smartphone-based GPS data collection to travel mode detection has none. The included studies were searched from six databases. The purpose of this review is to critically assess the current literature on the existing methodologies of travel mode detection based on GPS raw data collected by smartphones. Meanwhile, according to the systematic comparison among different methods from data-preprocessing to travel mode detection, this paper could carefully provide the Strengths and Weaknesses of existing methods. Furthermore, it is the crucial step to develop the methodologies and applications of GPS raw data collected by smartphones.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

Whey protein was pretreated with multi-frequency ultrasound in mono, dual, and tri-frequency modes. The effect of multi-frequency ultrasound pretreatment on the hardness, chemical forces, and microstructure of acid-induced whey protein gel was investigated. Whey protein gels pretreated with dual and tri-frequency ultrasound showed higher hardness (p3.35 mm) in those samples were resisted to gastric digestion. Moreover, the tri-frequency ultrasound pretreatment of whey protein gel released the least free amino group during gastric digestion. In contrast, whey protein gel with the mono-frequency ultrasound pretreatment released the highest amount of free amino acid group during intestinal digestion. Findings from this study suggested that gel hardness and network density could modulate the digestion behaviors of protein gels.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

Road traffic accidents are associated with different factors, such as non-signalized road networks, inexperienced drivers, lack of communication skills, distraction, and visual or cognitive impairment of road users, which have led to this increase in traffic accidents. Understanding these factors in alignment with road user communication skills can provide solutions that can reduce traffic fatalities. Road users’ communication is predominantly formal in nature, but informal means of communication also exist but are not given proper attention during the driving training and licence testing processes. Therefore, this study investigated communication skills between drivers as a factor contributing to traffic accidents in South African cities. Consequently, 16 traffic scenarios of communication between drivers were simulated using PTV Vissim and Blender software, and a semistructured interview questionnaire was used to collect data from South African road users. The questionnaire was further used to evaluate the confidence level of road users concerning informal communication. The data were analysed via regression analysis to establish the relationship between traffic accidents and miscommunication between drivers. The information gathered and analysed from this study helps to understand the informal communication types between drivers and establish where communication loss exists, which ultimately leads to a traffic accident. The results also show that misinterpretation of communication signals can present the possibility of traffic safety risk.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

This paper, from the perspective of Mode 3 of knowledge production, takes the important carrier of knowledge, scientific research papers, as the research object. The mainstream databases (SCIE and SSCI) are chosen as the data sources. Firstly, bibliometric methods are applied to analyze the cooperation status among the main bodies of paper production, including authors and their affiliated institutions, countries, and disciplines; secondly, the Analytic Hierarchy Process (AHP) is used to construct a comprehensive evaluation model for the state of research cooperation in carbon neutrality. Based on the evaluation model, the cooperation characteristics of different disciplinary fields and the relationship between paper cooperation status and high-impact research papers are comparatively analyzed. At the same time, an analysis is conducted on the support from the government, the sponsorship from enterprises, and the participation of the public in the process of paper production. Finally, some suggestions are put forward on how to build an innovative ecosystem for carbon neutrality research from the perspective of Mode 3 of knowledge production.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

To develop aryloxyphenoxypropionate herbicides with novel structure and improved activity, a total of twenty-eight novel quinazolinone–phenoxypropionate derivatives containing a diester moiety were synthesized and tested for herbicidal activity. The bioassay results in the greenhouse showed that QPEP-I-4 exhibited excellent herbicidal activity against E. crusgalli, D. sanguinalis, S. alterniflora, E. indica, and P. alopecuroides with inhibition rates &gt;80% at a dosage of 150 g ha-1, and displayed higher crop safety to G. hirsutum, G. max, and A. hypogaea than the commercial herbicide quizalofop-p-ethyl. Studying of the molecular mode of action by phenotypic observation, membrane permeability evaluation, and transcriptomic analysis revealed that a growth inhibition of plant by QPPE-I-4 was the result from damage of plants biomembrane. The evaluation of ACCase activity in vivo indicated that QPPE-I-4 could inhibit ACCase and may be a new type of ACCase inhibitor. The present work demonstrated that QPPE-I-4 could serve as a lead compound for further developing novel AOPP herbicides.

Chronic stress, culminating in burnout, evolves gradually and is notoriously difficult to detect due to vague symptoms and individuals' hesitance to acknowledge their struggles. To expedite the identification and recognition of this condition, enabling timely psychological intervention, the integration of Artificial Intelligence (AI) is increasingly considered. This research does not assert the feasibility of an AI system managing all aspects of chronic stress's impact. However, it highlights the capability of current technology to detect stress indicators based on quantifiable data like Heart Rate (HR) and organizational climate dimensions. Although other physiological markers such as oximetry, skin galvanic response, and EKG have been explored, they have not shown reliable differentiation between stress and joy. Focused on the unique context of school principals in the Bedouin regions of Israel, this study investigates the interplay between HR, organizational climate, and stress levels. It introduces a novel application of a fuzzy logic tool that combines HR and organizational climate metrics to aid in stress diagnosis. This tool incorporates the psychologist's expertise to provide real-time data crucial for developing effective coping strategies. While the AI-supported fuzzy system does not replace professional psychological intervention, it significantly enhances the speed of condition identification and intervention planning, thus shortening the response time to stress-related issues in educational leadership within culturally specific settings. The application of such AI-driven tools is pivotal for sustaining the well-being and effectiveness of educational leaders, thereby supporting the broader goal of educational sustainability.

Traumatic brain injury (TBI) is an important global clinical issue, requiring not only prevention but also effective treatment. Following TBI, diverse parallel and intertwined pathological mechanisms affecting biochemical, neurochemical, and inflammatory pathways can have severe impact on the patient’s quality of life. The current review summarizes evidence for utility of amantadine in TBI in connection to its mechanism of action. Amantadine combining multiple mechanisms of action may offer both neuroprotective and neuroactivating effects in TBI patients. Indeed, use of amantadine in TBI has been encouraged by several clinical practice guidelines/recommendations. Amantadine is also available as infusion which may be of particular benefit in unconscious patients with TBI, due to immediate delivery to the central nervous system and the possibility of precise dosing. In other situations, orally administered amantadine may be used. There are several questions that remain to be addressed: Can amantadine be effective in disorders of consciousness requiring long-term treatment and in combination with drugs approved for treatment of TBI? Do the observed beneficial effects of amantadine extend to disorders of consciousness due to factors other than TBI? Well controlled clinical studies are warranted to ultimately confirm its utility in the TBI and provide answers these questions.

The economic, social and environmental benefits generated by the use of urban public transportation infrastructure constitute a complex dynamic urban public transportation infrastructure utilization benefit system. This paper evaluates the coupling coordination among these three benefits taking four Chinese autonomous municipalities as an example. These four cities have large-scale urban public transportation infrastructures but their utilization has many serious problems. The basic function of urban public transportation infrastructure has not been fully played in these cities. Whether the different benefits of urban public transportation infrastructure have been developed in harmony or not is unclear. We analyzed the coordinated development among three benefits by constructing coupling coordination degree model and used Gini coefficient to study the difference of coordinated development among three benefits of four cities. The result shows that the levels of coordinated development among three benefits of urban public transportation infrastructure were lower in these four cities and have positive correlation with it of urban public transportation infrastructure utilization benefit. Raising the level of urban public transportation infrastructure utilization benefit is the most crucial solution of promoting the coordinated development among three benefits.

With a worldwide growing concern for greenhouse gas (GHG) emissions and their impact on human health and the environment, transportation has become a central theme in mitigation, responsible for 14% of human GHG emissions. To build endurance to climate change, transportation services must adapt to the current scenario and act quickly to avert future changes. Deeply rooted changes in socio-technical systems will be necessary to achieve significant CO2 reduction and secure the well-being of future generations. This study's objective is to comprehensively review the current state of carbon mitigation in the transportation sector. This is done through a systematic literature review engrained in the socio-technical transition theory and the structural theory of contingency. Twenty-six review papers covering 2,983 original articles are selected for full-text examination concerning carbon emissions in transportation. Enablers, barriers, benefits, disadvantages and metrics in carbon emissions reduction are identified, and a comprehensive framework is built. Results provide a view of the current sustainability scenario in transportation and allow a better understanding of the factors influencing carbon emission initiatives in transportation and its outcomes.

In this study, global response analysis was performed to explore the mechanism of action of Usnic acid and its synergy with Norfloxacin, a well-known quinolone antibiotic to which MRSA clinical isolates showed resistance (MIC, 500 µg/mL). Microdilution assay, growth kinetics, microscopic analysis, and cell-based assays consistently showed that Usnic acid possess strong anti-staphylococcal activity (MIC, 7.8 µg/ml), causes cell leakage, modulates efflux pump activity, and synergizes with Norfloxacin against multi-drug resistant clinical isolate MRSA 2071. Whole cell proteome profiling using gel-free based nano-LC-ESI-QTOF-MS/MS revealed several proteins whose expression was significantly modulated by Usnic acid and Norfloxacin alone or in combination. Usnic acid downregulated the abundance of RNA polymerase subunits (RpoB, RpoC), carbamoyl phosphate synthase large subunit (PyrAB), chaperone (GroEL), and adenylosuccinate synthetase (PurA). Interestingly, proteins found to be upregulated in the presence of Usnic acid and Norfloxacin included oxidative stress-related proteins such as peroxidase (Tpx), alkyl hydroperoxide reductase (AphC), and general stress protein (UspA). This study clearly showed that Usnic acid affects numerous cellular targets and can potentiate the action of Norfloxacin. Furthermore, an in-vivo study emphasized the use of Usnic acid to develop as a safe phytopharmaceutical to repurpose old antibiotics through combination therapy against MRSA infections.

Background: Amidst escalating climate change concerns, sustainable practices in healthcare logistics are critical. This study evaluates the ecological impact and efficiency of medical sample transportation using drones, combustion cars, and electric cars across diverse terrains and weather in Liechtenstein and Switzerland. Methods: We conducted a comparative analysis of CO2 emissions, transport distances, and delivery times for each transportation modality. Data collection involved multiple runs under various conditions, with CO2 emissions measured using onboard systems, and transport efficiency assessed via GPS tracking and time monitoring. Results: Combustion cars exhibited the highest average CO2 emissions at 159.5 grams per kilometer (g/km). Electric cars emitted significantly less, averaging 3.43 g/km, which is 2.15% of combustion car emissions. Drones were the most environmentally friendly, with an average emission of 0.09 g/km, representing 0.07% of combustion car emissions and 2.6% of electric car emissions. Drones also showed substantial transport efficiency, covering 17% shorter distances on flat terrain and 24% shorter in mountainous areas, with time savings ranging from 13% to 80%. Conclusion: This study highlights the potential of drone technology to revolutionize healthcare logistics by reducing environmental impact and optimizing operational efficiency. Integrating drones can significantly lower the carbon footprint, improve sample integrity, and enhance patient care, promoting a greener, more resilient healthcare system.

Human beings naturally move from one location to another in search of basic necessities. Road transportation is a low-cost, versatile, and widely accessible mode of transportation worldwide. However, using fossil-based (FB) fuels in transportation vehicles is inefficient, generates hazardous gases, and worsens environmental degradation. The current work assesses the application of clean fuels such as biofuels, natural gas, electricity, propane, and other emerging fuels to replace FB fuels in transport vehicles. Unlike FB fuels, the use of biohydrogen, biomethane, biodiesel, and bioethanol in transport vehicles resulted in emission reduction by 70 %, 63 %, 41 %, and 54 %, respectively, while electric vehicles lower maintenance costs, ensuring better engine performance, and better engine efficiency. The adoption of natural gas and propane as alternative fuels for transport vehicles is cost-effective, and promotes environmental sustainability. There is a need for targeted financial, infrastructural, and technical investments to further promote the application of these clean fuels for road transport application. The outcome of the study provides updated information and sensitizes automobile engineers, environmentalists, transport fleet operators, governments, and other stakeholders on the benefits derivable in the adoption of clean fuels as alternatives to FB fuels as transport vehicles fuel.

The purpose of this paper is to study the sliding mode control as a Ricci flow process in the context of a three-story building structure subjected to seismic waves. The stability conditions result from two Lyapunov- functions, the first associated with slipping in a finite period of time, and the second with convergence of trajectories to the desired state. Simulation results show that the Ricci flow control leads to the minimization of the displacements of the floors. 3D Ricci solitons projection via a semi-conformal mapping to a surface is also studied.

The analysis and simulation of water quality in distribution networks is a complex issue of great concern today. The analysis of the evolution of water age, as a simple indicator of water quality in the network, is of great interest in both design and operation phases. Understanding the factors that have the strongest influence on water quality is key to developing adequate strategies aimed at preserving it. This paper firstly analyses the factors with biggest influence in the tanks water age, to support the selection of the most appropriate configuration from the point of view of water quality during design phases. Then, the main considerations when modelling tanks following the different mixing models considered in Epanet have been presented. Also, a real tank behaviour has been characterised through field measurements and Epanet simulations in order to determine the best fitted mixing model.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

The real-time Railway Traffic Management Problem (rtRTMP) is discussed in the field of railway transportation. In this paper, rtRTMP is considered for planning shunting routes based on the use of routing methods on a spatial-temporal graph. An approach and algorithm of Spatial-Temporal Graph formation for rail yard transportation network is proposed. The idea is to construct an undirected loop-free Double Vertex Graph for determining optimal shunting routes consisting of several half-runs for several trains shunting under draw-out tracks capacity constraints. Experimental results on the rail yard simulation model are presented.

An effective method to inspect inaccessible nuclear power facility by interface wave which propagate along the shrink fit boundary of reactor head is proposed in this study. Reactor head is relatively thick to inspect from the outside of reactor by conventional ultrasonic testing. The proposed interface wave can propagate a long distance from the fixed transducer position. The inside of nuclear reactor is limited to access due to the high radiation, so transducers are located at outside of nuclear facility and interface wave propagates into the nuclear reactor for defect detection. The numerical simulation and experiments were carried out to validate the effectiveness of the proposed interface wave inspection method. Various defect cases simulating field failures are also presented with satisfactory detectability by the proposed technique with the features for defect classification.

This study aims to enhance multimodal transportation systems by mitigating CO2 emissions and enhancing operational efficiency. It introduces a novel centralized cargo concentration approach tailored for regions facing geographical challenges. The method proposes for direct transportation of cargo from its loading origin to export ports, bypassing intermediate hubs. The mathematical model determines the most efficient means of transport for each route, factoring in variables like distance, volume, and cargo type. Research results indicate that, in scenarios with a high concentration of cargo, multiple hubs may not be necessary, which could streamline transportation and logistics operations. Modal preferences vary based on regional dynamics and cargo characteristics, with rail and sea transport emerging as preferable options under specific circumstances, surpassing the efficacy of road transport. The proposed model showcases reductions in both logistics costs and CO2 emissions compared to road-centric scenarios. It underscores the strategic integration of diverse transportation modes as pivotal for enhancing efficiency and sustainability. This study furnishes a framework adaptable to optimizing multimodal transportation systems in regions sharing similar geographical and logistical attributes.

Epigallocatechin gallate (EGCG), the principal catechin in green tea, exhibits diverse therapeutic properties. However, its clinical efficacy is hindered by poor stability and low bioavailability. This study investigated solid particle-in-oil-in-water (S/O/W) emulsions stabilized by whey protein isolate (WPI) and sodium caseinate (NaCas) as carriers to enhance the bioavailability and intestinal absorption of EGCG. Molecular docking revealed binding interactions between EGCG and these macromolecules. The emulsions exhibited high encapsulation efficiencies and augmented EGCG bioaccessibility by 64% compared to free EGCG in a simulated gastrointestinal digestion model. EGCG-loaded emulsions demonstrated minimal cytotoxicity towards Caco-2 cells and facilitated EGCG transport across the intestinal epithelial layer without compromising tight junction integrity. Notably, EGCG-loaded emulsions protected Caco-2 cells against oxidative stress by suppressing intracellular reactive oxygen species generation. The results demonstrate the potential of WPI- and NaCas-stabilized S/O/W emulsions to enhance the bioavailability, intestinal absorption, and bioactivity of EGCG, expanding its applications in functional foods and nutraceuticals.

The integration of drone technology into healthcare logistics presents a significant opportunity to enhance the speed, reliability, and efficiency of medical sample transportation. This study inves-tigates the current advancements in drone technology, focusing on its application in the rapid and secure delivery of medical samples, particularly in urban and remote regions where traditional transportation methods often face challenges. Utilizing a combination of recent technological de-velopments such as AI-driven navigation systems, real-time monitoring, and secure payload management, the study examines how drones can mitigate logistical barriers like traffic conges-tion and geographical isolation. The research methodology includes a comprehensive review of recent case studies from various regions, illustrating the practical applications and benefits of drones in healthcare. The results demonstrate a substantial reduction in transportation time and costs, along with improved accessibility to healthcare services in underserved areas. The study concludes that, while challenges such as regulatory hurdles and privacy concerns remain, the on-going advancements in drone technology and supportive regulatory frameworks have the poten-tial to revolutionize medical logistics, ultimately improving patient outcomes and healthcare de-livery.

Plantar fasciitis is one of the most common causes of foot pain; in a significant percentage it is also associated with bone edema of the heel. A prospective randomized clinical trial was designed, in which 48 patients suffering from plantar fasciitis, with or without bone edema, were treated with temperature controlled high energy adjustable multi-mode emission laser and exercises (laser group) or with exercises only (control group). Patients were evaluated at recruitment (T0), at 2 (T1) and 6 months (T2), monitoring pain (with Visual Analogue Scale), functionality (with Foot Function Index) and perception of improvement (with Roles and Maudsley Score) and fascia thickness (with ultrasound examination). In both groups there was a significant improvement in pain, functional recovery, perception of remission and a reduction in plantar fascia thickness at T1 and T2. The laser group presented statistically better values at T2 for the Roles and Maudsley Score (z: 2.21; 0.027). Regression analysis showed that a greater reduction in fascia thickness occurred in the laser group (p-value: 0.047). In conclusion, the two conservative treatments were effective in patients suffering from plantar fasciitis, even in the presence of bone edema, but with lesser results.

Background: Bioelectrical impedance (BIA) and ultrasound (US) have become popular for estimating body fat percentage (BF%) due to their low cost and clinical convenience. However, agreement of these devices with gold standard method still require investigation. The aim was to analyze the agreement between a gold standard %BF assessment method with BIA and US devices. Methods: Twenty-three men (age 30.1 ± 7.7 years, 82.5 ± 14.9 kg, 1.77 ± 0.05 m) underwent Dual Energy X-Ray Absorptiometry (DXA), BIA (tetrapolar) and US (three-site method) %BF assessment. Pearson and concordance correlations were analyzed. T-test compared means between methods, and Bland Altman plots analyzed agreement and proportional bias. Alpha was set at &lt; .05. Results: Pearson coefficients between BIA and US with DXA were high (BIA = 0.94; US = 0.89; both p &lt; .001). Concordance coefficient was high for BIA (0.80) and moderate for US (0.49). BF% measured by BIA (24.5 ± 7.5) and US (19.4 ± 7.0) were on average 4.4% and 9.6% lower than DXA (29.0 + 8.5%), respectively (p &lt; .001). Lower and upper agreement limits between DXA and BIA were -1.45 and 10.31, while between DXA and US were 2.01 and 17.14, respectively. There was a tendency of both BIA (p = .09) and US (p = .057) to present proportional bias and underestimate BF%. Conclusions: Despite the correlation, the mean difference between the methods were significant, and the agreement limits are very wide. This indicate that BIA and US, as measured in this study, have limited potential to accurately measure %BF compared to DXA, especially in individuals with higher body fat.

Mode locked pulse generation has been reported using both active and passive mode locking schemes. Active mode locking technique has been proven to be an effective way to generate high-repetition-rate pulses by incorporating a modulator inside the laser cavity. Compared to actively mode locked lasers, passively mode locked lasers can generate pulse train at ultrashort pulse width but with relatively lower repetition rate. Thus, it is a brilliant idea to build a hybrid mode locked system combining both active and passive mode lockers. In this review, several hybrid mode locked fiber ring laser systems are discussed and summarized. Hybrid mode locking is a promising method to generate high speed ultrashort optical pulses for fiber-optic telecommunication system.

The main objective of this paper is to develop a readiness index model that can serve as an analytical tool for exploring the achievements of electrification of transportation systems. We have applied this readiness index model to evaluate the readiness positioning of China, Norway, and Sweden to-wards transport electrification. We have chosen these three countries as they represent diversity among countries that are in the process of adopting electric transport system solutions. Our developed readiness index model has four key dimensions, technological readiness, political readiness, societal readiness, and economic readiness. The embeddedness of all four dimensions in one model provides a multi-perspective way of analyzing and evaluating the readiness levels of countries moving towards transforming the transportation system. Therefore, we named the model a “multidimensional readiness index.” Our main conclusions are that the political processes and political decisiveness involved are the most important factors followed by the societal needs and economic ability, with the current technology available as the fourth. Without the participation of dedicated and determined political decision-makers being involved, the other three factors are challenging to obtain. Political decision-makers need to facilitate the use of economic means to support the transformation in the society and affected industries to balance the initial economic disadvantages of the electrically powered systems until they pass the cost disadvantage turning point. The development of the relevant technology is no longer a great barrier as it was at the beginning of this transformation, about 20 years ago. The technology for electrically powered transportation systems and devices is widely available now, although it is continuously evolving and being improved. Associated industries cannot be expected to initiate, finance, take the risk, and take the lead in this global societal transformation without clear and strong political support.

Municipal solid waste management is a major concern for developing countries all over the world. The collection and transportation accounts for major portion of expenditure in developing country like India. The compaction of waste is being practiced in some major cities of India as they provide economical benefit but the environmental benefits of compaction are not very clear. The preset study evaluates the environmental impacts due to transportation of non-compacted and compacted waste from the transfer station to the landfill site using life cycle assessment approach. The study compared transportation of non-compacted waste with the waste compacted by the truck mounted refuse compactor and portable stationary compactor. The functional unit defined was the amount of waste generated per day in the study area taken as Patna city and GaBi 10.5 used for impact assessment. The study found that the transportation of waste compacted by truck mounted refuse compactor had the least environmental impacts on all impact categories. The study recommends the compaction of waste by the truck mounted refuse compactor and then proceed for transportation. Also, the compaction of waste is recommended as it improve the overall environment performance of municipal solid waste management.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes, while axial canal is the largest canal amongst the network and distributes at the center of a coral branch. However, previous studies indicated that, in the non-radial symmetry transport system of Acropora, axial canal do not play a major role in the transport of hydroplasm, and the action of axial canal in coral growth is still obscure. In this study, we reconstructed six Acropora muricata samples by high resolution micro-computed tomography to investigate the growth patterns of axial canals during the processes of new branch forming and truncated branch rebuilding. We found that the axial canal of a new branch is transformed from a calice and the polyps in the new branch are budded from the polyp in the axial canal. Meanwhile, the axial canal can transport the calcareous skeletons to rebuild the tip of a truncated branch, which represents as the change in the diameter of axial canal and calcareous deposition/reduction in it. This work indicate the regulation of axial canal in the growth processes including budding, branching, and mineralising of an Acropora colony.

In response to the problem of poor detection ability of object detection models for small-scale targets in intelligent transportation scenarios, a fusion method is proposed to enhance the features of small-scale targets, starting from feature utilization and fusion methods. The algorithm is based on the YOLOv4 tiny framework and enhances the utilization of shallow and mid level features on the basis of FPN, improving the detection accuracy of small and medium-sized targets; In view of the problem that the background of the intelligent traffic scene image is cluttered and there is more redundant information, the CBAM attention module is used to improve the attention of the model to the traffic target; To address the problem of data imbalance and prior bounding box adaptation in custom traffic datasets that expand traffic images in COCO and VOC, we propose a Copy Paste method with improved generation method and a K-means algorithm with improved distance measurement to enhance the model's detection ability for corresponding categories. Comparative experiments were conducted on a customized 260 thousand traffic dataset containing public traffic images, and the results showed that compared to YOLOv4 tiny, the proposed algorithm improved mAP by 4.9% while still ensuring the real-time performance of the model.

Veterans face difficulties accessing vital health and community services, especially in rural areas. Autonomous vehicles (AVs) can revolutionize transportation by enhancing access, safety and efficiency. Yet, there is limited knowledge about how Veterans perceive AVs. This study fills this gap by assessing Veterans' AV perceptions before and after exposure to an autonomous shuttle (AS). Using a multi-method approach, 23 participants completed pre- and post-AS Autonomous Vehicle User Perception Survey (AVUPS), with 10 participants also taking part in post-AS focus groups. Following exposure to the AS, differences were observed for three out of the four AVUPS domains: an increase in Intention to Use (p &lt; 0.01), a decrease in Perceived Barriers (p &lt; 0.05), and an increase in Total Acceptance (p = 0.01); Well-being remained unchanged (p = 0.81). Feedback from focus groups uncovered six qualitative themes: Perceived Benefits (n=70), Safety (n=66), Shuttle Experience (n=47), AV Adoption (n=44), Experience with AVs (n=17), and Perception Change (n=10). This study underscores AVs' potential to alleviate transportation challenges faced by Veterans, contributing to more inclusive transportation solutions. The research offers insights for future policies and interventions aimed at integrating AV technology into the transportation system, particularly for mobility-vulnerable Veterans in rural and urban settings.

The condition of surface transportation infrastructure directly affects the economic health of a nation. However, it is difficult to justify the large sums of money needed to extend current methods to monitor all the multimodal infrastructure. The convergence of connected vehicle and cloud computing technologies presents an opportunity to automate the collection of ride quality and imagery data to continuously assess the condition of all roadways and railways. This paper presents several perspectives to help policy and standardization initiatives promote adoption.

During the past few years many projects and initiatives were undertaken deploying and testing automated vehicles for public transportation and logistics. However in spite of their ambition, all of these deployments stayed on the level of elaborated experimentation deploying no more than 4 maximum 5 AVs in rather small sites (few Kms of roads) and never really reached the level of large scale “commercial” deployment of transport services. The reasons for this are many, but the most important being the lack of economically viability and commercially realistic models, the lack of scalability of the business and operating models, and the lack of inclusive citizen/user centric services required for the large end-user acceptation and adoption of the solutions. In this paper, based on the experience gained in the H2020 AVENUE project, we present the missing pieces of the puzzle, ad which will be addressed in the Horizon Europe project ULTIMO.

In this paper, bikeshare data in Chicago on weather-friendly days in 2019 and 2020 were analyzed to investigate the variation in bikeshare travel before and during the pandemic. Our results show that bikeshare trips during the pandemic were much longer than prior to the pandemic. The increased rate of bikeshare usage was unbalanced spatially and varied significantly for different user types. Specifically, bikeshare was used significantly more by casual users than by subscribers, and the increase occurred much more in the outskirts of the city. The increase in bikeshare travel was associated with a reduction in travel by ride-hailing and public transit, especially in the urban periphery. The correlation of bikeshare use with the bus system was much less significant than with the rail system. Bike lanes/facilities had a mixed effect on bikeshare travel. Weekend bike trips increased in areas where there was no bike lane. Weekday trips, on the contrary, increased in the vicinity of bike greenways.

In this paper, a multi-mode waveguide-based optical resonator is proposed for an integrated optical refractive index sensor. Conventional optical resonators have been studied for single-mode waveguide-based resonators to enhance the performance, but mass production is limited owing to the high fabrication costs of nano-scale structures. To overcome this problem, we designed an S-bend resonator based on a micro-scale multi-mode waveguide. In general, multi-mode waveguides cannot be utilized as optical resonators, because of a performance degradation resulting from modal dispersion and an output transmission with multi-peaks. Therefore, we exploited the mode discrimination phenomenon using the bending loss, and the resulting S-bend resonator yielded an output transmission without multi-peaks. This phenomenon is utilized to remove higher-order modes efficiently using the difference in the effective refractive index between the higher-order and fundamental modes. As a result, the resonator achieved a Q-factor and sensitivity of 2.3x10³ and 52 nm/RIU, respectively, using the variational finite-difference time-domain method. These results show that the multi-mode waveguide-based S-bend resonator with a wide line width can be utilized as a refractive index sensor.

This study provides a thorough review and analysis of the evolution of the Greek vehicle fleet over the last ~30 years, which is next used for the generation of high granularity fleet projections and for the estimation of relevant environmental benefits by 2030. The integrated methodology developed takes also into account vehicle clustering and the Brown’s Double Simple Exponential Smoothing technique that together with the adoption of COPERT based emission factors allow for the estimation of the anticipated emissions in 2030. Expected 2030 emissions levels suggest a reduction across all pollutants in comparison to 2018, ranging from 3.7% for PM10 to 54.5% for NMVOC (and 46% for CO, 14% for SO2, 28% for NOX and 21% for CO2). We find that Greece is on track with national goals concerning the reduction of air pollution from the transportation sector, stressing the positive contribution of EVs and new, "greener" vehicles, and setting new challenges for the further improvement of the sector beyond the 2030 outlook.

In this study, the team employed full-scale crash tests to investigate the impact of post-densification technology on the safety performance of separated central median W-beam barriers under low compaction conditions. By precisely simulating the design and construction environment of the central median, the study comprehensively evaluated the barrier's containment, redirection, buffering, and anti-intrusion performances, as well as the deformation of both the barrier and vehicles under various collision scenarios. The results indicate that under low compaction soil conditions, the A-level separated central median barriers reinforced with post-densification technology effectively meet the specified protection requirements. By comparing the influence of soil strength variations on barrier performance under simulated rainfall conditions, it was confirmed that enhancing soil compaction significantly improves soil stability, effectively increases the overall strength and stability of the barriers, reduces deformation, and significantly enhances safety performance. This study not only validates the effectiveness of the reinforcement scheme but also provides new perspectives for the scientific research of safety barriers and offers crucial technical support for the optimal design of road safety protection facilities.

Extant research pays little attention to migrant workers’ skill accumulation/upgrading from the perspective of the labor supply. This paper takes China as an example to explore the factors influencing skill accumulation of rural-urban migrant workers (RUMWs), with a purpose to discover how to sustain or reshape regional competitive advantage through improving RUMWs’ skill accumulation. Structured questionnaire surveys were adopted for data collection in Suzhou City, Jiangsu Province and Taizhou City, Zhejiang Province located in the Yangtze River Delta in the east of China. 900 questionnaires were issued and 491 effective questionnaires were recovered totally. This paper takes a perspective of global production networks, and gets a broad viewpoint containing intra-firm coordination, inter-firm partnership and extra-firm bargaining with non-firm actors, beyond what the extant literature on laborers’ human capital focuses on. The finding indicates that firms’ skill-oriented preference, which concerns about employees’ skills and innovation ability and stimulates them to learn initiatively, have a significant influence on RUMWs’ skill accumulation. In terms of collective efficiency based on co-competitive relationship between local firms, the more intensive interactions are, the more opportunities of skill accumulation RUMWs get. The accessibility of local institutions and favorable policies benefit RUMWs’ skill accumulation. Besides, the place itself, as a synthesized space of labor-management relations inside a firm and inter-organization relations, exerts an influence on and cause the regional differences in RUMWs’ skill accumulation.

With the extension of the post-catch circulation time, a series of changes had taken place in the soft tissue of the live clams, resulting in the decline of its quality. This study investigated the quality changes of clams (Ruditapes philippinarum) in cold chain and was mainly focused on the rehydration process, which included gradient heating rehydration (GR) and sudden heating rehydration (SR). It was found that the GR had a better effect on the quality of clams than the SR. The GR stage clams showed a higher survival rate, glycogen content and adenylate energy charge (A.E.C) value than the SR stage clams. Conversely, the GR stage clams showed lower lactic acid content and K-value than the SR stage clams. The results indicated that the gradient heating rehydration was beneficial to the quality of clams. The transportation and rehydration strategies benefited both producers and shellfish merchants to save total cost.

Pesticides are chemical compounds or mixtures of hazardous substances that are used by humans to increase and protect crops from pests and control disease-carrying insects. Because of its wide use, it may be poisonous to helpful and non-targeting plants and animals. Spraying or spreading pesticides over whole fields of crops can cause runoff to transfer the chemicals into aquatic ecosystems, and wind can carry the chemicals to nearby grazing regions, farms, and populated areas, where they can endanger other animals. This review summarises recent studies on pesticide combination toxicity to aquatic biota and approaches used to anticipate toxic effects. When toxicants harm economically significant organisms that humans consume, the negative effects become more severe and can cause stress conditions, vital organ damage, biochemical damage, or even the death of living things in both terrestrial and aquatic environments. Pesticides are highly toxic to aquatic organisms such as snails, fish, etc. Neurological dysfunction in freshwater organisms is also caused by pesticides. By producing excessive ROS, pesticides can cause severe biochemical and histological changes in freshwater organisms. So, it is therefore easy to understand the attention of the public on these substances. Because aquatic organisms play a major part in the food chain. However, through the biomagnification process, the quantity of pesticides increases in the higher organisms through the food chain. Which results play a terrific role in the higher organism’s body. So, It's essential to comprehend the way that insecticides work on aquatic organisms. In this review article, we are focusing on the way that pesticides work, which will help in the system of biomonitoring.