Monitoring and maintenance of cracked structures are generally done using structural integrity assessments. The plastic zone (PZ) crack path (CP) criteria state that a crack grows in the direction when the radius of the plastic zone ahead of the crack tip reaches a minimum value. The PZ can be evaluated using Stress intensity factors (SIF). The SIFs under mixed-mode loading were extracted from literature from three samples: two SENT samples made from polycarbonate and one modified C(T) sample made from low-carbon steel. In addition, the CP angle was evaluated for the W and R-criteria. It was found that both can predict the CP for lateral cracks in both tested materials and monotonic and cyclic load when the mode-mixity does not change considerably from one crack length to the next one or goes beyond 0.2. Moreover, the R-criterion exhibited an error as high as 1.7%, whereas the W-criterion showed a 6% error on the last crack length for the low carbon steel sample under cyclic load, which had a 100% increase in mode-mixity. Finally, the applicability of LEFM is checked, while the CP is sought by finding the size of the PZ.

In this work, an algorithm was developed to measure the respiration rate for an embedded device that can be used by a field robot for relief operation. With this algorithm, the rate measurement was calculated based on direct influences of respiratory-induced intensity variation (RIIV) on blood flow in cardiovascular pathways. For that, a photoplethysmogram (PPG) sensor was used to determine changes in heartbeat frequencies. The PPG sensor readings were filtered using an Information Filter and a Fast Fourier transform (FFT) to determine the state of RIIV. With a relatively light initialization, the information filter can estimate unknown variables based on a series of measurements containing noise and other inaccuraties. Therefore, this filter is suitable for application on an embedded device. For faster calculation time in the implementation, the FFT analysis was calculated only for a major peak in the frequency domain. Test and measurement of respiration rate was conducted based on the device algorithm and spirometer. Heartbeat measurement was also evaluated by comparing the heartbeat data of the PPG sensor and the medical tool kit. Based on the test, the implemented algorithm can measure respiration rate with about 80% accuracy compared with the spirometer.

Expansion tube is ideal energy absorber which dissipates kinetic energy through plastic deformation and friction. There is an urgent need to understand the influence of key parameter, e.g. semi angle, tube material, and friction coefficient, on the mechanical response and energy absorption characteristics of expansion tube. In the present work, the material properties of the tubes were tested under quasi-static loading condition, and the numerical simulations were carried out by using commercial software ABAQUS. Based on the validated finite element simulation, all the semi angle, tube material, and friction have significant effects on the energy absorption capacity of expansion tube. The expansion tube with high tensile stress of parent material have high energy absorption capacity, while the specific energy absorption is linear with the tensile stress/density of tube material. This work would give a guidance to the structural design and parent materials selection for expansion tubes.

In this work, new refinements of some numerical radius inequalities are proved. Namely, new improvements and refinements purify the recent inequalities of some famous inequalities concerning the numerical radius of Hilbert space operators. The proven inequalities in this work are not only an improvement over old inequalities, but rather they are stronger than them. Several examples that support the validity of our results are established as well.

The recent Planck Legacy release confirmed the existence of an enhanced lensing amplitude in the cosmic microwave background (CMB) power spectra, which endorses the positive curvature of the early Universe with a confidence level exceeding 99%. In this study, the pre-existing curvature is incorporated to extend the field equations where the derived wave function of the Universe is utilized to model Universe evolution with reference to the scale factor of the early Universe and its radius of curvature upon the emission of the CMB. The wave function reveals both positive and negative solutions, implying that matter and antimatter of early Universe plasma evolve in opposite directions as distinct Universe sides. The wave function indicates that a nascent hyperbolic expansion is followed by a first phase of decelerating expansion away from early plasma during the first 10 Gyr, and then, a second phase of accelerating expansion in reverse directions, whereby both Universe sides free-fall towards each other under gravitational acceleration. Simulations of the predicted conformal curvature evolution demonstrate the fast orbital speed of outer stars owing to the external fields exerted on galaxies as they travel through conformally curved space-time. Finally, the wave function predicts an eventual time-reversal phase comprising rapid spatial contraction that culminates in a Big Crunch, signalling a cyclic Universe. These findings reveal that early plasma could have separated and evolved into distinct sides that collectively and geometrically influencing the Universe evolution, physically explanting the effects attributed to dark matter and energy.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

In this brief paper we will propose a new equation for the proton charge radius. We will base our new equation on the Trinhammer-Bohr formula which states that the proton charge radius is directly proportional to the proton Compton wavelength. We will then propose a new equation for the proton Compton wavelength which is inversely proportional to the Rydberg constant and directly proportional to the running value of the fine structure constant on the protonic scale. This will define the proton charge radius only by the effective value of the fine structure constant and the Rydberg constant. This new equation also disproves the old value of the proton charge radius 0.877(50) which was measured by using electron-proton scattering and further solidifies the newer and smaller values 0.8414(19) provided by NIST.

In this work, some numerical radius inequalities based on the recent Dragomir extension of Furuta's inequality are obtained. Some particular cases are also provided.

There are many criterion to generalize the concept of numerical radius; one of the most recent interesting generalization is what so called the generalized Euclidean operator radius. Simply, it is the numerical radius of multivariable operators. In this work, several new inequalities, refinements and generalizations are established for this kind of numerical radius.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

(1) Background: Although diagnostic criteria for massive hemorrhage with organ dysfunction such as disseminated intravascular coagulation associated with delivery have been empirically established based on clinical findings, strict logic has yet to be used to establish numerical criteria. (2) Methods: A dataset of 107 deliveries with ≥2,000 g of blood loss, among 13,368 deliveries from nine national perinatal centers in Japan between 2020 and 2023 was obtained. Twenty-three patients had fibrinogen levels <170 mg/dl, which is the initiation of coagulation system failure per our previous reports. Three of these patients had hematuria. We used six machine learning methods to identify the borderline criteria dividing the fibrinogen/fibrin/fibrinogen degradation product (FDP) planes, using 15 coagulation fibrinolytic factors. (3) Results: The boundaries of hematuria development on a two-dimensional plane of fibrinogen and FDP were obtained. If the FDP–fibrinogen/3–60 (mg/dl) value is positive, this indicates hematuria; otherwise, the case is non-hematuria, as demonstrated by the support vector machine method that seemed the most appropriate. (4) Conclusions: The borderline criterion dividing the fibrinogen/FDP plane for patients with hematuria that could be considered organ dysfunction in massive hemorrhage during delivery was obtained using artificial intelligence, and this method seemed to be useful.

Psoriasis is a chronic, multisystem, inflammatory disease. The typical clinical cutaneous manifestation of psoriasis is scaly erythema or plaque, limited or widely distributed. However, psoriasis is far beyond the skin involvement and provides many challenges, including associated comorbidities. In this review, we classify psoriasis as cutaneous and systemic psoriasis, according to the clinical diversity and associated comorbid diseases, and recommend classification criteria for psoriasis. The key objective of this novel classification is to raise awareness of the complexity of this multifaceted disease and help to better understand and manage this complex disease comprehensively.

We propose two methods for obtaining estimations on the minimum distance and covering radius of orthogonal arrays. Both methods are based on knowledge about the (feasible) sets of distance distributions of orthogonal arrays with given length, cardinality, factors and strength. New bounds are presented either in analytic form and as products of an ongoing project for computation and investigation of the possible distance distributions of orthogonal arrays with parameters in doable ranges.

In this work, we report the magnetocaloric effect (MCE) in a quantum dot corresponding to an electron interacting with an antidot, under the effect of an Aharonov-Bohm flux subjected to a parabolic confinement potential. We use the Bogachek and Landman model, which additionally allows the study of quantum dots with Fock-Darwin energy levels for vanishing antidot radius and flux. We find that the Aharonov-Bohm flux (AB-flux) strongly controls the oscillatory behaviour of the MCE, thus acting as a control parameter for the cooling or heating of the magnetocaloric effect. We propose a way to detect AB-flux by measuring temperature differences.

The effect of the communication channel size on the transport and subsequent detection of chemical messengers is investigated on millimetric and micrometric channels. The transport of the information carriers, being characterized by an advective and a diffusive contribution, was simulated by varying the flow velocity and the diffusion coefficient. Then, to evaluate the information quality, the Intersymbol Interference (ISI) between two consecutive signals at a specific release delay was estimated. This allowed us to verify that operating under micrometric channel conditions has a larger flow velocity range to obtain completely separated successive signals and smaller release delays can be used between signals. The theoretical results were confirmed by developing a prototype molecular communication platform operating under microfluidic conditions, which enables communication through fluorescent nanoparticles, namely Carbon Quantum Dots (CQDs).

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

A membrane ozonation contactor was built to investigate ozonation using tubular membranes and to inform computational fluid dynamics (CFD) studies. Non-porous tubular polydimethylsiloxane (PDMS) membranes of 1.0 – 3.2 mm inner diameter were tested at ozone gas concentrations of 110 – 200 g m−3 and liquid side velocities of 0.002 m s−1 – 0.226 m s−1. The dissolved ozone concentration could be adjusted to up to 14 mg O3 L−1 and increased with decreasing membrane diameter and liquid side velocity. Experimental mass transfer coefficients and molar fluxes of ozone were 1.1∙10−5 mol m−2 s−1 and 2.4∙10−6 m s−1, respectively, for the smallest membrane. CFD modelling could predict the final ozone concentrations but slightly overestimated mass transfer coefficients and molar fluxes of ozone. Model contaminant degradation experiments and UV absorption measurements of ozonated water samples in both ozone (O3) and peroxone (H2O2/O3) reaction systems in pure water, river water, wastewater effluent and solutions containing humic acid show that the contactor system can be used to generate information on the reactivity of ozone with different water matrices. Combining simple membrane contactors with CFD allows predicting ozonation performance under a variety of conditions leading to improved bubble-less ozone systems for water treatment.

We consider a Cauchy problem for differential equations in a Hilbert space $X$. The problem is stated in a time interval $I$, which can be finite or infinite. Weuse a fixed point argument for history-dependent operators to prove the unique solvability of the problem. Then, we state and prove convergence criteria for both a general fixed point problem and thecorresponding Cauchy problem. These criteria provide necessary and sufficient conditions on a sequence $\{u_n\}$ which guarantee its convergence to the solution of the corresponding problem, in the space of both continuous and continuously differentiable functions. We then specify our results in the study of a particular differential equation governed by two nonlinear operators. Finally, we provide an application in viscoelasticity and give a mechanical interpretation of the corresponding convergence result.

Published data or available literature on sustainable building plan-design, construction, performance, and renovation criteria have covered some stages or some parts of each stage. These data usually have been published partially in many different papers―there have not been any papers that published these data together. Hence, this paper aims to collectively review these data and publish them together. The collection and review of these data were carried out by our twenty-five team members who specialized in sustainable urban, architectural, and civil engineering and construction management. The gathered and reviewed outputs were combined and validated based on a general group consensus. This consensus decision-making proceeded through two major group meetings with several follow-up meetings. The first major meeting was to combine and improve the gathered reviewed sustainable building criteria for Cambodia. The second major meeting was to validate the improved reviewed sustainable building criteria for Cambodia. The several follow-up meetings were to discuss the relevance and importance of the validated data “criteria and their classifications and descriptions” in all stages and more focused on their importance and applicability to Cambodia. The collective reviewed data in this paper would be useful to researchers in the fields. They could also be useful collective knowledge and information for policymakers from governmental agencies and development partners, particularly for sustainable building and construction companies.

The centrifugal force field in the hydrocyclone was affected by the concave-wall curvature radius R0, the mechanism of droplet deformation was closely related to the mass transfer efficiency. Numerical simulation and experimental data were collected to reveal the deformation characteristics and mechanism of single droplet crossing concave-wall jet. Normalized interfacial energy γ and stretching performance were provided to investigate the droplet deformation process. The results showed that the droplet was stretched along the streamwise and shrank along the spanwise in the concave-wall jet. The droplet interfacial energy and deformation were the largest when the droplet crossed the jet boundary at t = 0.20 s. Maximum γ value increased with the increase of R0 by 57.3% to 71.4%, and the distance between droplet and concave-wall increased with R0. Q-criterion was exported to show the vortex strength increasing as the decrease of R0 in the jet boundary. The pressure distribution inside the droplet showed that the pressure decreased as R0 increased, while the pressure difference increased along the streamwise and wall-normal direction. The study suggested that the droplet breakup was more difficult for the smaller R0, which was beneficial for liquid-liquid heterogeneous separation.

This article introduces an innovative design method for public lighting systems that surpasses the limitations of conventional approaches, which rely on predefined lamp characteristics and spatial arrangement. By employing a multi-criteria decision algorithm, our study proposes an optimal design methodology considering several key aspects, including the distance between lamps, their type, power, and light distribution. The goal is to achieve optimal illumination that enhances visibility on public roads for drivers and pedestrians while simultaneously minimizing glare, installation costs and maximizing energy efficiency. The proposed methodology is implemented through an algorithm developed in Matlab, with results validated through simulations in Dialux. This information is used to construct a decision matrix, assessed using the CRITIC method across 180 different scenarios within a specific case study. The findings demonstrate the effectiveness of multi-criteria decision-making as a tool for significantly improving the planning and design of lighting in public illumination systems, allowing for selecting the optimal combination of parameters that ensure the best lighting conditions.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

The importance of frailty in older people is getting constant recognition as an important aspect both in terms of public health, as well in personal level for the appropriate management of an older person health condition. This is reflected by the continuously increasing number of research studies carried out in several settings across different countries. Sometimes this is very solid, but in other cases there is a considerable gap in terms of accurate and well grounded documentation of frailty status. This is the case in Greece, where we are missing clinically validated tools to approach frailty. We are missing frailty screening tools, such as for instance PRISMA 7, the gold standard tool of Fried criteria is somehow problematic since the question referring to physical activity originates from a questionnaire that has not been translated and validated, while Clinical Frailty Scale has been validated for the translation but not for the capacity to detect frailty. Aim of this study is to validate these tools for their accuracy to detect frailty by using a measurable index of frailty, previously proposed for use in clinical studies: the Short Physical Performance Battery (SPPB). 74 male and female participants have been evaluated for their frailty status using different tools. We observed that PRISMA 7 translation detects frailty only when one question is removed at a cut-off of ≥ 2 and indicated a sensitivity of 88.1%, and specificity of 99.9% with a good correlation with SPPB measurements (r = 0.858; p < 0.001). When CFS was validated using SPPB it demonstrated a very good correlation (r = -0.838; p < 0.001 respectively) as it was the case for the modified Fried Criteria (r = -0.725; p < 0.001). All items demonstrated a good correlation between them. We can here propose that we can accurately assess frailty status in the community setting by using a modified version of Fried criteria, Clinical Frailty Scale translation in Greek and we can screen for frailty by using the Greek translation of PRISMA 7 only after removing the item 6 of the questionnaire.

In this paper is proposed an analytical technique which can be used to obtain the forced response of a cantilevered tube conveying fluid. Considering the pipe subjected to an arbitrary harmonic force either distributed or concentrated, an analytical solution is found using Green’s function method. The solution obtained of the closed form satisfies the differential equations in a classical sense. The presented method giving the exact solutions is more precise than the classical eigenfunction expansion or Galerkin’s method with no need to the eigenfunctions or eigenvalues.

The study of ecosystems, both natural and artificial, has historically been mediated by population dynamics theories. In this framework, quantifying population numbers and related variables (associated with metabolism or biological-environmental interactions) plays a central role in measuring and predicting system-level properties. As we move towards advanced technological engineering of cells and organisms, the possibility of bioengineering ecosystems (from the gut microbiome to wildlands) opens several questions that will require quantitative models to find answers. Here, we present a comprehensive survey of quantitative modelling approaches for managing three kinds of synthetic ecosystems, sharing the presence of engineered strains. These include test tube examples of ecosystems hosting a relatively low number of interacting species, mesoscale closed ecosystems (or ecospheres), and macro-scale, engineered ecosystems. The potential outcomes of synthetic ecosystem designs and their limits will be relevant to different disciplines, including biomedical engineering, astrobiology, space exploration and fighting climate change impacts on endangered ecosystems. We propose a space of possible ecosystems that captures this broad range of scenarios and a tentative road map for open problems and further exploration.

Background: Neurosarcoidosis is a great mimic, and its distinction from multiple sclerosis and other disorders can be particularly troublesome. We investigated whether cerebrospinal fluid (CSF) examination could help distinguish these two conditions and propose new diagnostic criteria. Methods: Stringent hierarchical diagnostic criteria were formulated. These were then applied prospectively to 531 neurological patients in whom neurosarcoidosis entered the differential diagnosis. The CSF total protein (TP), white cell count (WCC) and angiotensin-converting enzyme (ACE) levels were measured. The CSF and serum IgG patterns after isoelectric focusing were compared. Not all CSF parameters were measured in every patient. Results: 85/531 (16%) cases examined were diagnosed with neurosarcoidosis. Only 22 of these 85 (26%) met stringent diagnostic criteria. Intrathecal synthesis of oligoclonal IgG was evident in only 1/19 (5%) who fulfilled these criteria compared to 19/59 (32%) cases who did not (p = 0.03). CSF TP levels > 1g/L were more common in patients meeting the stringent criteria compared to the remainder of the patients, i.e. 11/22 (50%) vs 14/58 (24%) (p<0.05). Eleven out of 20 cases (55%) fulfilling stringent criteria had elevated CSF WCCs, and 6/12 cases (50%) had raised CSF ACE, neither significantly different from the remaining cases. Mean CSF TP, WCC, and ACE levels did not differ significantly between any groups of patients. Interpretation: Large elevations in CSF total protein, white cell count, and ACE occur in neurosarcoidosis but are rare in multiple sclerosis. However, the diagnostic use of these tests is limited since minimal changes may occur in both conditions. In contrast, intrathecal synthesis of oligoclonal IgG is a powerful discriminator because it is very uncommon in neurosarcoidosis whilst occurring in 95-98% of cases of multiple sclerosis. This observation implies that the immunopathogenesis of the two disorders is quite different. We suggest caution in diagnosing neurosarcoidosis when intrathecal oligoclonal IgG synthesis is detected. We propose new diagnostic criteria for neurosarcoidosis for future research.

The sugar company Valdez S.A. Entity located within the geographical limits of the city of Milagro, needs to reduce its emissions to the environment and does not always comply with the air emissions standards for stationary combustion sources, which indicates that for equipment installed before 2003 they have a maximum limit of 300 mg / m³. A mist eliminator was designed to work inside the original wet gas scrubber of the water-tube cauldron #10, which uses Bagasse as fuel, for the generation of steam for industrial use. The research is documentary and field. The methodology used was mixed. focusing on the comparison of three types of technologies to meet the objectives, the fog eliminators types: Demister, Cyclone and Chevron. To find the appropriate complement, a comparison sheet was made, which is a table of contents evaluated quantitatively, analyzing indicators formulated in each of the contents. The results, supported by the Multiple Criteria Decision Analysis methodology, select the Chevron type fog eliminator, with the best efficiency for capture. Using AutoCAD, allows to visualize in 3D, the structural design in the gas scrubber.

The idea that the Earth system self-regulates in a habitable state was proposed in the 1970s by James Lovelock, who conjectured that life plays a self-regulatory role on a planetary-level scale. A formal approach to such hypothesis was presented afterwards under a toy model known as the Daisyworld. The model showed how such life-geosphere homeostasis was an emergent property of the system, where two species with different properties adjusted their populations to the changing external environment. So far, this ideal world exists only as a mathematical or computational construct, but it would be desirable to have a real, biological implementation of Lovelock's picture beyond our one Biosphere. Inspired in the exploration of synthetic ecosystems using genetic engineering and recent cell factory designs, here we propose such a living, microbial Daisyworld. This is based on a synthetic microbial ecosystem using pH as the external, abiotic control parameter. Several case studies are considering, including two, three and multiple species assemblies. Despite that oscillatory dynamics and chaos emerge in the latter case, it is shown that global regulation is also achieved in most cases as species diversity increases. The alternative implementations and their implications of this model in other synthetic biology scenarios, including ecosystem engineering, are outlined.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

To address the issue of traditional static evaluation models being unable to comprehensively analyse the performance of ultra-supercritical coal-fired units under varying loads, we propose a dynamic comprehensive evaluation model based on the improved Criteria Importance Through Inter-criteria Correlation (CRITIC) method and Entropy Weight Method (EWM). The comprehensive performance evaluation index system of ultra-supercritical coal fired units is constructed by examining the boiler performance, turbine performance, plant power performance, environmental performance, and flexible performance of coal powered units. The CRITIC and EWM methods are used to calculate the weights of the indicators, which are then combined with the static evaluation results. Using a dynamic comprehensive evaluation model, we analysed ultra-supercritical coal-fired units, taking into account time weight. This allowed us to obtain the comprehensive dynamic real-time evaluation value of the units under different loads. The research indicates that the dynamic comprehensive evaluation model, which uses an improved CRITIC and EWM, has significant advantages in improving evaluation accuracy, weight-balanced distribution, and generality. Provides more accurate, reasonable, and reliable evaluation results for practical decision making.

Familial dysbetalipoproteinemia (FD) is a highly atherogenic genetically-based lipid disorder with the underestimated actual prevalence. In the recent years, several biochemical algorithms have been developed to diagnose FD using available laboratory tests. However, there is not enough data on their use in real-world clinical implementation. We studied the applicability of the most accessible biochemical algorithms to diagnose FD in clinical practice. We also investi-gated the prevalence of FD in one of the European regions of Russia based on a population sample. In this study there was detected a high prevalence of FD: 1 in 151. We demonstrated that the diagnostic algorithms of FD including a diagnostic apoB levels require correction, taking into account the characteristics of the distribution of apoB levels in the population. At the same time a triglycerides cutoff ≥1.5 mmol/L may be a useful tool in identifying subjects with FD. We also analyzed the presence and pathogenicity of APOE variants associated with the autosomal dominant FD in a large research sample.

Buildings can generate heats which are mostly generated from the machinery using inside the buildings, and these heats generally released to the atmosphere. Buildings can also block the wind flow by their canopies and trap the heat by using low albedo materials. These causes pointedly contribute to urban heat island and greenhouse effects. Likewise, urban development and building construction in Cambodia are growing rapidly. The construction has been recognized as a key development sector while thousands of buildings are being built and have been operated in the main cities. However, those buildings mostly have not been considered to incorporate sustainability concepts while the major final energy consumers in the country are buildings. The buildings’ energy consumption is also projected to increase more than double until 2040. Hence, sustainable building promotion in Cambodia is necessary, and sustainable building criteria are completely required. This research aims to find out significant sustainable building criteria for Cambodia and focused on planning and design criteria because having proper planning and design is a smart start leading to achieving building sustainability in all stages. This research used the Delphi methods to validate the relevant sustainable building criteria available in the literature and then select the significant ones for Cambodia based on the Delphi consensus. The results showed that ninety-nine consensus planning and design criteria were found to be significant for sustainable buildings in Cambodia.

(1) Background: A growing number of communities are re-discovering the value of their streets as important public spaces for many aspects of daily life, thus creating the need for a transformation in the quality of streets. An emerging concept is to accommodate all users of the transportation system, a concept that has been labelled ‘complete streets’. (2) Methods: In this paper, we present sustainable complete streets design criteria that integrate complete streets by adding in socio-environmental design criteria related to aesthetics, environment, liveability, and safety. (3) Results: Proposed design criteria provide a street network which provides improvements in aesthetics, to recover historical urban character and realize historical area planning goals; environment, to increase permeable surfaces, reduce the heat island, and absorb traffic-related air pollution; liveability, to create a public space destination in the urban landscape; and safety, to improve the safety of all road users. and (4) Conclusions: The case study of the urban rehabilitation of the “Mostra d’Oltremare” area and of its cultural and architectural assets in Naples, Italy, highlights the practical application of the proposed criteria and the possibility of using these criteria in other urban contexts.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

In this study, the efficiencies of flat-plate and U-tube solar collectors were investigated experimentally when an Al₂O₃ nanofluid was used as a working fluid and compared to those of solar collectors using water. The energy saving and CO₂ and SO₂ generated were calculated and compared to those of solar collectors using water. In addition, based on the experimental results, an economic analysis of the use of solar collectors in various countries was performed. As the concentration of the Al₂O₃ nanofluid increased, the performance of the solar collector improved. The highest efficiency for the solar collectors was shown at the concentration of 1.0 vol% with the nanoparticle size of 20 nm. The maximum efficiencies of the flat-plate and U-tube solar collectors using 1.0 vol%-Al₂O₃ nanofluid with 20-nm nanoparticles was 74.9% and 72.4%, respectively, when the heat loss parameter was zero. The efficiencies of the flat-plate and U-tube solar collectors using Al₂O₃ nanofluid were 14.8% and 10.7 higher, respectively, than those using water. When 50 EA flat-plate solar collectors were operated for one year using Al₂O₃ nanofluid, the coal use, generated CO₂, and generated SO₂ were 189.99 kg, 556.69 kg, and 2.03 kg less than those of solar collectors using water, respectively. In addition, the largest electricity cost reduction was in Germany.

Purpose: This study aimed to elucidate the various new classifications and the use of LDLT in this context for HCC beyond milan criteria. Methods: The clinical data of patients with HCC outside milan criteria who underwent LT at Jena University between Januar 2007 and August 2023 were retrospectively analyzed. Eligible patients were classified according to various classification systems. Clinicopathological features, overall- and disease-free survival rates were compared between the two groups (LT vs. LDLT) and in context for bridging therapy. Results: Among the 245 patients analyzed, 120 patients were outside milan criteria and 125 patients were inside milan. There was no significant difference for patients outside milan in overall survival for LT versus LDLT (OS 44,3 months vs. 28,3 months; 5y survival, 56,4% vs. 40%; p = 0.84). G3 tumor differentiation, presence of angioinvasion and lack of bridging were statistically significant risk factors predicting tumor recurrence in univariate and multivariate analysis (HR 6.34; p = 0.0002; HR 8.21; p < 0.0001; HR 7.50; p = 0.0001). Bridging therapy before transplantation provides a significant survival advantage regardless of the transplant procedure (OS: p = 0.008 ; DFS: p < 0.001). Conclusions: Patients with HCC outside milan criteria who underwent LT or LDLT had comparable outcome to patients inside milan criteria. Nevertheless, these patients remain disadvantaged on the waiting list, which is why LDLT represents a safe alternative to LT and should be considered in bridged HCC patients depending on tumor differentiation, size and tumor marker dynamics.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

The steady state tube furnace (SSTF) (ISO/TS 19700) was used to assess the effects altering the reaction zone of a flame had on smoke toxicity measurements. The gas inlet of the apparatus was modified to allow for a mixture of nitrogen and air to be introduced into the system. The volume of air used in each test remained at 2 L min-1 , and additional volumes of nitrogen were varied between tests altering the total volume of gas used in the primary gas inlet. The chosen conditions were representative of under-ventilated flaming by using a restricted oxygen environment. The research shows that the increase in volume flow of gas over a sample increased the smoke toxicity of the materials tested (CO and HCN). When increasing the volume of the primary air-flow through the tube furnace, the flow causes thinning of the flame zone in the apparatus and results in gaseous species spending less time in the reaction zone, resulting in less time available for chemical reactions to occur. This resulted in less complete combustion occurring, and hence an increased yield of measured products of incomplete combustion (CO and HCN), and a decreased yield of products of complete combustion (CO2).

. The impedance change of an induction coil surrounding a metal tube adapter is investigated by the truncated region eigenfunction expansion (TREE) method. Conventional TREE method is inapplicable to this problem as a consequence of the numerical overflow of eigenfunctions of the air-metal multi-subdomain regions. The difficulty is surmounted by a normalization procedure for the numerical eigenfunctions obtained from the finite element method (FEM). Efficient algorithm is devised by the Clenshaw-Curtis quadrature rule for integrals involving the numerical eigenfunctions. Numerical results of the TREE and FEM simulation coincide very well in all cases, and the efficiency of the proposed method is also confirmed.

Piriform fossa and/or esophageal injuries caused by calibration tubes are relatively rare and re-main unelucidated. Herein, we report the case of a 36-year-old woman with morbid obesity, sleep apnea, and menstrual abnormalities who was scheduled to undergo laparoscopic sleeve gastrectomy (LSG). We inserted a 36-Fr Nelaton catheter made of natural rubber as a calibration tube during the surgery. However, excessive resistance was observed. We confirmed a submuco-sal layer detachment of approximately 5 cm from the left piriform fossa to the esophagus using intraoperative endoscopy. Additionally, LSG was performed using an endoscope as the guiding calibration tube. We inserted a nasogastric tube under endoscopy with a guidewire before com-pleting the surgery, hoping for a guiding effect on saliva flow. After 17 months, the patient suc-cessfully lost weight postoperatively without complaints of neck pain or discomfort during swallowing. Therefore, if the damage is limited to the submucosal layer, as in this case, conserva-tive therapy should be considered, which is similar to the concept of not requiring suture closure in endoscopic submucosal dissection. This case highlights the risk of iatrogenic injuries to the pi-riform fossa and/or esophagus during LSG and the importance of careful calibration tube inser-tion to prevent them.

Liquid manipulation by photoisomerization attracts recent attentions as a new active droplet control method for micro-chemical analysis. Such a non-inverse manipulation can be realized by a use of solution liquid of surfactant that exhibits the \emph{cis}-\emph{trans} isomerization triggered by light irradiation with a specific wavelength such as ultraviolet light. Since the isomerization is accompanied by changes in fluid properties, a light irradiation on one of liquid-air interfaces of a liquid column in a tube would generate differences in the wettability accompanied between the both sides of the finite liquid column. Although this technique has been demonstrated experimentally by Muto et al. (\emph{Euro.~Phys.~J.~Special Topics}, {\bf 226}, 2016, 1199--1205), its dynamics and developments of each isomer distribution are not understood. In order to reveal the liquid-column migration phenomenon, we have performed numerical simulations of air-liquid two-phase flows and its scalar transport of the isomer, using the Volume-of-Fluid method in conjunction with the Continuum-Surface-Force model and Continuous-Species-Transfer method. We validated present results by comparison with experimental result in terms of the migration distance of the liquid column. We confirmed a termination of the liquid-column migration occurs when the \emph{cis} isomer distribution reaches the non-irradiated region. The migration speed was less dependent on the liquid-column length and was proportional to the tube diameter.

This is a short note on a new way to describe Haug's newly introduced maximum velocity for matter in relation to the Schwarzschild radius. This leads to a probabilistic Schwarzschild radius for elementary particles with mass smaller than the Planck mass. In addition, our maximum velocity, when linked to the Schwarzschild radius, seems to predict that particles just at that radius cannot move. This implies that radiation from the Schwarzschild radius not can undergo velocity time dilation. Our maximum velocity of matter, therefore, seems to predict no time dilation, even in high Z quasars, as has surprisingly been observed recently.

Living beings are composite thermodynamic systems in non-equilibrium conditions. Within this context, there are a number of thermodynamic potential differences (forces) between them and the surroundings, as well as internally. These forces lead to flows, which, ultimately, are essential to life itself. Living beings are under the pressures of natural selection, thus are biological flows as well. At the same time, the maintenance of homeostatic conditions, the tenet of physiology, demands regulation of these flows by control of variables. However, due to the very nature of these systems, regulation of flows and control of variables become entangled in closed loops. Therefore, the search for adaptation in flows takes a different path than the search for adaptation in morphological traits. Being at the roots of transfer processes, thermodynamic criteria turn out to be as natural physical candidates. Likewise, being at the roots of physiology, control turns out to be as a natural biological candidate in that path. Here we show how to combine entropy generation, with respect to a generalized process, and control of parameters (in such a generalized process) in order to create a criterium of optimal ways to regulate changes in generalized flows.

Incremental stability analysis for time-delay systems has attracted more and more attentions for its contemporary applications in transportation processes, population dynamics, economics, satellite positions, etc. This paper researches criteria on v(t)-incremental stability, which is defined to demonstrate the convergence rate for incremental stability, for time-delay systems. Firstly, the sufficient conditions for v(t)-incremental stability for time-delay systems with continuous right-hands are studied, and several corollaries for specific cases are provided. As for time-delay systems with discontinuous right-hands, after expounding the relevant conditions for the existence and uniqueness of the Filippov solution, by using approximation methods, sufficient conditions for v(t)-incremental stability are obtained. The conclusions are applied to linear switched time-delay systems and Hopfield neural network system with composite right-hand afterwards.

The purpose of this study is to propose a consecutive manufacturing process system to secure the productivity of excellent STKN540B steel tube in the respect of economy and safety as the supporting material for mega structures such as building, bridge and ship. The components of consecutive manufacturing are press-bending, orbital auto welding and steel tube correction. By using STKN540B a high-strength steel material with low yield point that requires a special manufacturing process unlike other steel materials, an actual tube manufacturing is carried out at each stage in this experimental study. With this, the quality of steel tube and the efficiency of the manufacturing process are analyzed to draw out some points to improve in the future.

In order to improve the performance of the draft tube in hydraulic turbine, a multi–objective optimization method for the draft tube is developed by combining the design of experiment (DOE), the radial basis function (RBF) and the non–dominated sorting genetic algorithm (NSGA–II) in this paper. The geometrical design variables of the median section in the draft tube and the cross section in its exit diffuser are considered as design parameters in this optimization, which objective function is to maximize the pressure recovery factor (Cp) and minimize the energy loss coefficient (ζ). The limited numbers of design matrix required for the shape optimization of the draft tube is generated by optimal Latin hypercube (OLH) method of the DOE technique, of which performances are evaluated through computational fluid dynamic (CFD) numerical simulation. For reducing of the computational consumption, the approximate model is used based on the RBF. The Pareto optimal solutions are finally performed using the NSGA–II for obtaining the best geometrical parameters of the draft tube. The optimization result of the draft tube shows a marked performance improvement over the original, which verifies the theoretical validity and feasibility of the proposed method in this paper.

This paper explores the urgent necessity for practical guidance of infrastructure stakeholders aimed to promote sustainable infrastructure development, aligning with the United Nations Sustainable Development Goals (SDGs) and European Union (EU) regulations. Despite overarching definitions, there is a noticeable absence of a unified set of sustainability criteria, which delays the integration of sustainability principles into infrastructure planning, development, and operations. Through a systematic literature review and content analysis, this study seeks to clarify characteristics of sustainable infrastructure. Utilizing a content analysis of 124 sources, carefully selected through a structured exclusion process, the authors construct a comprehensive set of indicators. Subsequently, these indicators undergo rigorous evaluation by sector experts through structured focused group discussions on the relevance of the proposed sustainable infrastructure criteria to local planning contexts. The study's findings underscore the adequacy of the proposed criteria, albeit with variations in perceived importance. Additionally, focus group participants encourage for field-testing the criteria within a municipal setting before scaling up to national-level policy frameworks.

The aim of this article is to make a multi-criteria analysis of various exhibition spaces of an originally non-exhibition character and to determine how these spaces affect the selection of works and the exhibition concept. The analysis is based on the exhibitions of art objects at collective exhibitions in unconventional architectural spaces: commercial, i.e. the modern office building of PBG Gallery Skalar Office Centre in Poznań, post-industrial i.e. in the former Zakłady Przemysłu Ziemniaczanego Lubanta S.A. and in the historic interior of the "U Jezuitów" Gallery of the Cultural Integration Centre in Poznań. The multi-criteria comparative analysis shows a variety of features of the studied spaces as well as the relationship between architecture and art and their mutual interaction. The participatory role of the non-exhibition space in the process of creating an exhibition and selecting works has been proven. It has also been confirmed that the presentation of works of art in originally non-exhibition spaces creates a new quality of the artwork. Unconventional architectural space, when used for the exhibition of works of art, expands and strengthens the area of ​​their influence through the interaction between the work and the architectural space. The specificity of the space adapted for exhibition needs, the presence and type of architectural details in the interior, the quantity and quality of light and its distribution in space, the volume and colour of the interior determine the exhibition space and influence the shape of the exhibitions organised and the reception of the artworks. The only condition for the change of the original function of an architectural space into that of an exhibition space is a coherent artistic vision of the creator. This should take into account the appropriate selection of the exhibited objects, where the process of searching for the relationship between architecture and art determines the features of the architectural space as integral components influencing the realisation of the exhibition .

Lewis et al. published an important and timely necessary article about the determination of death by neurological criteria, revising the Uniform Determination of Death.The acceptance of brain death (BD) has been progressively accepted beginning at the late 1950s. Nonetheless, contentious brain-death cases have recently raised new controversies about the diagnosis of BD, such as the Jahi McMath case, extensively covered by the US and international press. Jahi McMath meant a terrible tragedy for her and her family. But further than this gloomy story, the case has also raised confusion and challenging qualms about a fundamental query: how we confirm whether a person is dead or alive? Since 1981, the Uniform Determination of Death Act (UDDA) has served as the legal foundation for the medical practice of determining death. But, although death by neurologic criteria is considered legal death throughout the United States, several recent lawsuits have quizzed the rightfulness the authority of the UDDA to declare death by neurological criteria. This issue explains the importance of Lewis’s et al. paper. In this article I want to present the historical procedure for issuing a law in Cuba for the determination and certification of death. Of course, it is impossible to compare our country with USA. Cuba is a small and developing country, in which a law encompasses a national scenery, in contrast with USA, a multistate nation.

Abnormal filamentous aggregates formed by tangled tau protein turn out to be classic amyloid fibrils, meeting all criteria defined under the fuzzy oil drop model in the context of amyloid characterization. The model recognizes amyloids as linear structures where local hydrophobicity minima and maxima propagate in an alternating manner along the fibril’s long axis. This distribution of hydrophobicity differs greatly from the classic monocentric hydrophobic core observed in globular proteins. Rather than becoming a globule, the amyloid instead forms a ribbonlike (or cylindrical) structure, which can be thought of as a distorted spherical micelle, which in limit form appears to be the ribbon-like micelle.

The reconstruction of traffic accidents has grown as an interdisciplinary field since the first accident occurred. Various methods have been developed over time, starting with primary data collected at the scene of the accident. In this work, I proposed a method by which the value of the force in the safety belt buckle can be determined when it is equipped with a pretensioning system with pyrotechnic trigger in the tube, PBP or PLP type. The anti-return system of the pretensioner mechanism, which prevents the passenger's body from moving forward, contains a set of balls that block the movement of the piston in the pretensioner tube after its activation. When limiting the movement, the force the human body exerts on the safety belt webbing is transformed into the deformation of the pretensioner tube by the balls of the anti-return system. Depending on the magnitude of the force, the marks left by the balls differ. I propose a relationship of dependence between the acting force and the deformation of the tube. An experimental test bench was created to perform shock traction tests on the pre-tensioning system, under similar conditions to those of the human body acting on the belt in case of a frontal collision. Following the tests, the force value of the seat belt buckle cable and the diameter of the spherical indentations that the balls left in the pretensioner tube were measured. A mathematical model was proposed to determine the normal force with which a ball from the anti-return system deforms the tube. The normal force was also determined by two other methods specific to contact mechanics and used in the specialized literature. By comparing the normal forces obtained by the three methods, a good correlation between the proposed mathematical model and the Komvopoulos-Ye method resulted, the "Hardness" method not being suitable for this study. The determined polynomial regression curve allows finding out the force in the cable of the closer depending on the size of the deformations produced by the balls in the tube. The forces in the belt webbing can be thus determined and biomechanics specialists can evaluate the injuries to the chest and abdomen of the occupants of a vehicle.

This study aimed to investigate the efficacy of probiotics in elderly hospitalized tube-fed patients undergoing antibiotic therapy for Clostridium difficile-associated diarrhea (CDAD). Probiotics were administered to 29 patients, with twice-daily doses for 7 days following the completion of antibiotic treatment. In the probiotic group, while stool form showed no significant change, there was a significant decrease in stool frequency. Conversely, the control group exhibited improved stool form but not frequency. The probiotic group maintained a significant difference in stool form during the follow-up period. Additionally, the control group showed a positive correlation between stool form, frequency, antibiotic therapy, and intensive care unit admission, which was not observed in the probiotic group. These findings suggest that supplementing with probiotics can effectively normalize stool form in elderly hospitalized tube-fed patients undergoing antibiotic treatment for CDAD, highlighting the potential benefits of probiotic intervention in this specific population.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Eddy current based approaches have been investigated for a wide range of inspection applications. Dodd-Deeds model and the truncated region eigenfunction expansion (TREE) method are widely applied in various occasions, mostly for the cases that the sample is relatively larger than the radius of the sensor coil. The TREE method converts the integral expressions to the summation of many terms in the truncated region. In a recent work, the impedance of the co-axial air-cored sensor due to a plate of finite radius was calculated by the modified Dodd-Deeds analytical approach proposed by authors. In this paper, combining the modified analytical solution and the TREE method, a new finite region eigenfunction expansion (FREE) method is proposed. This method involves modifying its initial summation point from the first zero of the Bessel function to a value related to the radius of the plate, therefore makes it suitable for plate with finite dimensions. Experiments and simulations have been carried out and compared for the verification of the proposed method. Further, the planar size measurements of the metallic circular plate can be achieved by utilising the measured peak frequency feature.

This study is focused on the development of criteria for night and visual line of sight (VLOS) flights, especially in the context of beyond visual line of sight (BVLOS) drone applications. While BVLOS technology is advancing globally, regulatory restrictions and conservative legal regulations often prohibit these flights. The goal is to provide experimental guidelines for operational procedures in night and BVLOS flights. The study aims to establish empirical criteria for physical distances in night and VLOS flights, using a test team composed of a pilot, recorder, and observers. The observers are tasked with assessing the identification and recognition distances, which are crucial for safe drone operations. The criteria established are based on different variables such as aircraft size, altitude, and visual acuity. This research involves extensive flight tests at varying altitudes using different types of drones and observers with differing visual acuities (20/20, 20/13.3, and 20/10). The study also examines the effect of communication equipment limitations on recognition distance and the use of lighting devices to minimize abnormal conditions during nighttime flights. Overall, the study's findings aim to contribute to the safe and efficient planning of BVLOS and night drone flights, especially considering the ever-evolving technology and regulatory landscape in this field.

Construction of Pontoons is based on multiple elements, dimensions and weight. The study has addressed about how the industry of the floating reinforcement concrete precast (pontoons) installs in the factory with the combinations of utility, electricity services, and Internet service. The pontoon bridges are successfully installed in the road for transport or sea for shops. The installation process for pontoons is successfully attempted in a balanced situation above surface of the sea to the resistant of floating precast (pontoons) to any ambient effects such as weather conditions, the movement of the waves or any others effects. The findings elaborate that it is not just a military solution. Pontoon installation can significantly serve for civil purposes.

The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Features of nanosecond discharge development in a non-uniform electric field are studied experimentally. High spatial resolution imaging showed that thin luminous tracks of great length with a cross-section of a few microns are observed against the background of discharge glow in air and argon. It has been established that the detected tracks are adjacent to brightly luminous white spots on the electrodes or to the vicinity of these spots, and are associated with the flight of small particles. It is shown that the traces have various shapes and change from pulse to pulse. The particle tracks may look like curvy or straight lines. In some photos, they can change the direction of movement to the opposite. The particle trace was found to abruptly cut off and a bright flash is visible at the trail break point. The color of the tracks differs from that of the spark leaders, while the bands of the second positive nitrogen system dominate in the gap spectra during the existence of a diffuse discharge. Areas of blue light are evident near the electrodes, as well. Development of glow in the gap during its breakdown is revealed using an ICCD camera. Physical reasons for the observed phenomena are discussed.

The co-circulation of duck hepatitis A virus subtypes 1 (DHAV-1) and 3 (DHAV-3) in ducklings has resulted in significant economic losses. Because ducklings infected with DHAV-1 or DHAV-3 show similar clinical signs and gross lesions, it is important to discriminate these subtypes as early as possible for better clinical management. On the basis of multiple alignments of the 5′-noncoding region sequences of strains DHAV-1 and DHAV-3, universal and type-specific primers were designed and synthesized. Using the primers in a one-tube reverse transcription-PCR (RT-PCR) assay, reference strains of DHAV-1 and DHAV-3 (isolated over a span of 60 years and covering many different countries) were successfully amplified, indicating that the primer sequences were completely conserved. The amplicon sequences results and the sizes of amplicons from reference DHAV-1 and DHAV-3 isolates correlated completely with their genotypes. Moreover, with this one-tube RT-PCR system, the amplicon sizes of liver samples of reference DHAV-1- or DHAV-3-infected birds matched perfectly with their respective genotypes, as determined by virus isolation and neutralization tests. No other RNA viruses of duck origin were detected with the synthesized primers. The sensitivity of viral RNA detection was 10 pg. With this system, 20% genotype 1, 45% genotype 3, and 9% co-infection of the two genotypes were detected in 55 clinical samples. This novel approach could be used for the rapid genotyping DHAV-1 and/or DHAV-3 infection in routine clinical surveillance or epidemiologic screening.

Depressive disorder is a disease that causes a decrease in daily function, and the prevalence of depressive disorder in Korea is the highest among OECD countries. However, due to lack of manpower and negative social awareness, timely treatment is not being performed properly. As a solution to this, AI counseling chatbots are emerging, and it is essential to use labeled datasets to create chatbots. Currently, many countries around the world, including Korea, use the Diagnostic and Statistical Manual of Mental Disorders Fifth Edition, DSM-5, but there are no nine labeled datasets according to the DSM-5 depression disorder diagnosis criteria. This study collects sympathetic datasets, analyzes morphemes using Kind Korean Morpheme Analyzer and augments and builds a word dictionary using Word2Vec. As a result, we have labeled the dataset with nine criteria for diagnosing DSM-5 depressive disorder, which will enhance the performance of the counseling chatbot.

Current global commitments to reduce emissions of greenhouse gases encourage national targets for renewable generation. Due to its small land mass, offshore wind could help Bahrain to fulfill its obligations. However, no scoping study has yet been carried out. The methodology presented here addresses this research need. It employs Analytical Hierarchy Process and pairwise comparison methods in a Geographical Information Systems environment. Publicly available land use, infrastructure and transport data are used to exclude areas unsuitable for development due to physical and safety constraints. Meteorological and oceanic opportunities are ranked, then competing uses are analyzed to deliver optimal sites for wind farms. The potential annual wind energy yield is calculated by dividing the sum of optimal areas by a suitable turbine footprint, to deliver maximum turbine number. Ten favourable wind farm areas were identified in Bahrain’s territorial waters, representing about 4% of the total maritime area, and capable of supplying 2.68 TWh/yr of wind energy or almost 10% of the Kingdom’s annual electricity consumption. Detailed maps of potential sites for offshore wind construction are provided in the paper, giving an initial plan for installation in these locations.

Hollow and concrete-filled steel tubes (CFSTs) are widely used as columns in many structural systems and local buckling can occur when they are subjected to axial compression loading. The critical regions for the local buckling of the columns are near the ends of the column where the moments are the highest. To strengthen the critical regions of the CFSTs the CFRP provides a simple and effective method which used previously as an enhancement for both of strength and ductility. So, this study suggests investigating the axial load behaviour of CFST strengthened with CFRP using FE method after a verification study and then a various parametric studies were carried out to cover the effect of the CFRP layers, number, confinement length and position. The FE results proved that, one CFRP sheet with thickness equal to 1.2 mm was strengthened the composite column by 8.5%, two CFRP sheets with total thickness equal to 2.4 mm was strengthened the composite column by 23.5%, three CFRP sheets with total thickness equal to 3.6 mm was strengthened the composite column by 35.1% and four CFRP sheets with total thickness equal to 4.8 mm was strengthened the composite column by 44.5%. Moreover, this study proved that by strengthened the composite columns with CFRP sheets with different lengths, the axial load resistance was improved by 8.5%, 4.6%, 0.1% and 0.0% for length percentages 100%, 75%, 50% and 25% respectively.

The thoracic surgery has increased drastically in recent years, especially in the light of the severe outbreak of 2019 novel coronavirus disease (COVID-19). Routine “passive” chest computed tomography (CT) screening of inpatients detects some pulmonary diseases requiring thoracic surgeries timely. As an essential device for thoracic anesthesia, the double-lumen tube (DLT) is particularly important for anesthesia and surgery. With the continuous upgrading of the DLTs and the widespread use of the fiberoptic bronchoscopy (FOB), the position of DLT in thoracic surgery is gradually becoming more stable and easier to observe or adjust. However, the DLT malposition still occurs during transferring patients from supine to lateral position in thoracic surgery, which leads to lung isolation failure and hypoxemia during one-lung ventilation (OLV). Recently some innovative DLTs or improved intervention methods have shown good results in reducing the incidence of DLT malposition. This review aims to summarize the recent studies of the incidence of left-sided DLT malposition, the reasons and effects of malposition, and summarize current methods for reducing DLT malposition and prospects for possible approaches. Meanwhile, we use bibliometric analysis to summarize the research trends and hot spots of the DLT research.

Important first phases in the process of implementing CO2 subsurface and ocean storage projects include selecting of best possible location(s) for CO2 storage, site selection evaluation. Sites must fulfil a number of criteria that boil down to the following basics: they must be able to accept the desired volume of CO2 at the rate at which it is supplied from the CO2 source(s); they must as well be safe and reliable; and must comply with regulatory and other societal requirements. They also must have at least public acceptance and be based on sound financial analysis. Site geology; hydrogeological, pressure, and geothermal regimes; land features; location, climate, and access, etc. can all be refined from these basic criteria. In addition to aiding in site selection, site characterization is essential for other purposes, such as foreseeing the fate and impacts of the injected CO2, and informing subsequent phases of site development, including design, permitting, operation, monitoring, and eventual abandonment. According to data from the IEA, in 2022, emissions from Africa and Asia's emerging markets and developing economies, excluding China's, increased by 4.2%, which is equivalent to 206 million tonnes of CO2 and were higher than those from developed economies. Coal-fired power generation was responsible for more than half of the rise in emissions that were recorded in the region. The difficulty of achieving sustainable socio-economic progress in the developing countries is entwined with the work of reducing CO2 emissions, which is a demanding project for the economy. Organisations from developing countries, such as Bangladesh, Cameroon, India, and Nigeria, have formed partnerships with organisations in other countries for lessons learn and investment within the climate change arena. The basaltic rocks, coal seams, depleted oil and gas reservoirs, soils, deep saline aquifers, and sedimentary basins that developing countries (Bangladesh, Cameroon, India, and Nigeria etc) possesses all contribute to the individual country's significant geological sequestration potential. There are limited or no carbon capture and storage or clean development mechanism projects running in these countries at this time. The site selection and characterization procedure are not complete without an estimate of the storage capacity of a storage location. Estimating storage capacity relies on volumetric estimates because a site must accept the planned volume of CO2 during the active injection period. As more and more applications make use of site characterization, so too does the body of written material on the topic. As the science of CO2 storage develops, regulatory requirements are implemented, field experience grows, and the economics of CO2 capture and storage improve, so too will site selection and characterisation change.

Arguments of Mises and Hayek, who opposed the planned economy (PE), are used in the paper as a starting point for establishing the objective area of effective application of the PE. The abstract model of PE, based on the definitions of Mises and Hayek, leads to the conclusion that for the effective use of PE, it must be a part of mixed economy and it must produce a limited amount of essential goods of irreducible demand. These goods must be distributed among all members of society free of charge, evenly, without competition. Examples of a mixed economy are given that meet this requirement. Calculations of the personal benefit in the transition to a mixed model of the economy have been carried out. The positive and negative qualities of the planned and market methods of organization are considered. Mixed economy model combines these qualities in optimal construction. An analytical framework has been introduced for the construction of product characterization curves. Such curves provide criteria for determining the efficiency of manufacturing of this product in a planned economy. The general economic prerequisites for the usability of the PE are clarified. The applicability and advantages of the PE for the organization of the universal basic income (UBI) system are demonstrated. The possibility of using PE to solve the problem of guaranteed employment is mentioned.

Primary spontaneous pneumothorax (PSP) is a pleural disease that abruptly affects healthy adolescents and young adults, representing a common thoracic disorder in this age group. This study aimed to investigate the necessity of preoperative chest tube insertion in patients with PSP and to re-evaluate current clinical treatment approaches. A retrospective review of medical records was conducted for children and young adults aged 14–30 years, diagnosed with PSP and who underwent Video-assisted thoracoscopic surgery (VATS) between January 2016 and December 2022 at Wonju Severance Christian Hospital. Patients were retrospectively divided into two groups based on their initial treatment: chest tube insertion and non-chest tube insertion. Clinical data including demographics, treatment details, and outcomes were collected and compared. Total 128 cases of PSP were included in the study. The total length of hospital stay was significantly shorter in the non-chest tube group (p=0.000), which was attributed to the omission of pre-operative chest tube insertions. No significant differences were observed between the two groups in terms of postoperative complications or recurrence rates. In cases of young patients with PSP, omitting pre-operative chest tube insertion may be a viable option if the patient is scheduled for VATS.

In a power plant that uses seawater as a coolant, a debris filter is required to remove foreign substances from the seawater, and differential pressure leads to a decrease in the coolant flow rate, leading to a decrease in power generation efficiency. In this study, analysis was performed under different initial flow velocity conditions of 1.5m/s, 2.0m/s, and 2.5m/s for a debris filter used in a power plant to understand flow characteristics in CTCS. The flow and differential pressure characteristics of a CTCS with an installed debris filter were considered in a comparative analysis of velocity, pressure, and turbulent kinetic energy distribution. The results confirmed that a vortex was generated in the pipe with the debris filter, apparently due to the collision of the flow with the bracket of the debris filter. As the flow rate increased, the range of the vortex increased, causing a loss in flow.

The pulsating flow is one of the techniques which can enhance heat transfer, therefore leading to energy saving in tubular heat exchangers. This paper investigates the heat transfer and flow characteristics in a two-dimensional in-line tube bundle with the pulsating flow by a numerical method using the Ansys Fluent. Numerical simulation is performed for Reynolds number Re = 500 with different frequencies and amplitude of pulsation. Heat transfer enhancement was estimated from the central tube of the tube bundle. Pulsation velocity had an asymmetrical character with a reciprocating flow. The technique developed by the authors to obtain asymmetric pulsations was used. This technique allows simulating an asymmetric flow in heat exchangers equipped with a pulsation generation system. Increase in both the amplitude and the frequency of the pulsations has a significant effect on heat transfer enhancement. Heat transfer enhancement is mainly observed in the front and back of the cylinder. At a steady flow in these areas, heat transfer is minimal due to the weak circulation of the flow. The increase in heat transfer in the front and back of the cylinder is associated with increased velocity and additional flow mixing in these areas.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

This qualitative study explores sustainable procurement practices and supplier selection criteria, delving into the complexities, challenges, and opportunities of integrating sustainability considerations into procurement decisions. Through in-depth interviews with procurement professionals from diverse industries, the research uncovers key themes such as the multifaceted nature of sustainable procurement criteria, the challenge of assessing and managing suppliers' sustainability performance, the importance of collaboration and communication, and the influence of regulatory and market pressures. Findings reveal that sustainable procurement involves a comprehensive approach that considers environmental, social, and ethical factors alongside traditional criteria like cost and quality. Assessing suppliers' sustainability performance emerges as a significant challenge, necessitating robust assessment processes and technological solutions to enhance transparency and traceability. Collaboration and communication with suppliers are identified as critical enablers of sustainable procurement, fostering trust and mutual understanding. Regulatory mandates and market demands drive organizational commitments to sustainability, shaping supplier selection criteria and procurement strategies. Despite challenges, sustainable procurement offers benefits such as enhanced risk management, cost savings, innovation, and reputation enhancement. Overall, sustainable procurement represents a strategic approach that contributes to positive environmental and social outcomes, supporting a more sustainable and equitable future for organizations and society.

The management of an organization's human resources is the first stage in the governance process for any operation. This present study examine the strategies employed in Saudi Arabia for establishing effective governance through the implementation of human resource management practices and the key sustainable strategies criteria for effective human resource management practices. This step is considered crucial in governance as it involves the selection of highly qualified individuals who are expected to contribute to the achievement of optimal governance outcomes and the overall well-being of the population within a nation as well as the key criteria involves. Qualitative research methodology as well as Decision making trial and evaluation laboratory (DEMATEL) were utilized with a sample of 31 participants from 8 government ministries and 14 companies in Saudi Arabia. The study's findings from qualitative interview exert four key criteria influencing sustainable effective human resources management practices. Cultural reflection" is the most important long-term goals of Saudi Arabia's HRM initiatives found from DEMATEL evaluation impacting three criteria with7.9181, 8.2294, 8.1961 above the threshold value of 7.783599781. This means that HR professionals should take the time to study and evaluate the cultural dynamics at work, in order to promote cultural introspection and understanding of cultural differences.

The sustainable development and operation of mining enterprises as major sources of economic growth in many countries is determined by both a balance of economic, environmental, and social objectives and the resources required to achieve these objectives. Transportation is one of the main resources at open pits. It accounts for up to 70% of open pit operating expenses. Various parameters of transportation means should be coordinated both with the parameters of the open pit and meet the conditions of its operation. The problem of selecting a dump truck model in the paper is solved using a universal system of selection criteria developed using an original methodology. The two-level system of criteria includes all currently known selection criteria. The peculiarity of the methodology is the use of the multi-criteria FUCOM method for ranking the criteria. In addition, it is proposed to differentiate the criteria evaluations according to the experts' competence levels. Sets of criteria for evaluation by experts of different levels are proposed. The obtained criterion ranks are recommended to be used by managers of mining enterprises to choose a dump truck model. The presented methodology is suitable for the development of new systems of criteria, considering significant changes in operating conditions or the emergence of factors not considered in this study. Evaluation of all models of dump trucks on the market using the developed system of criteria is envisaged by the authors in a future study.

This paper focuses on robust multi-criteria traffic network equilibrium problems with path capacity constraints. The concepts of robust vector equilibrium and robust vector equilibrium with respect to worst case are introduced, respectively. To generate a subset of robust vector equilibrium, an equivalent min-max optimization problem is constructed. In addition, a direct search algorithm, in which the step size without derivatives and redundant parameters, for solving this min-max problem is proposed. To find a subset of robust vector equilibrium with respect to worst case, an equivalent smoothing optimization problem based on a variant version of ReLU activation function is established. Numerical experiments are also presented to expound the advantages of the algorithms.

Some researchers in Taiwan argue that the current mechanism by which government subsidies are allocated for smart city demonstration projects warrants improvement. A comprehensive literature review determined that the development potential of smart cities should be prioritized in site selection for such demonstration projects. This study developed an evaluation framework on the basis of multi-criteria evaluation methods to enable the identification of suitable smart community demonstration sites. Evaluation criteria were first identified through the Delphi method. Next, the weights of each criterion were derived through the analytic hierarchy process. Furthermore, the capability of the proposed evaluation model was determined through simulation testing.

There is an increasing pressure by community and customers forcing companies to insert environmental concerns in their practices. To help companies initiatives, the green bonds market was incepted. Our research question is how to select bonds in a growing billion-dollar market. This paper presents a multi-criteria decision analysis (MCDA) model to enable investors identify opportunities based not only in opinions, but grounded on objective facts. Analytic Hierarchy Process (AHP) and Complex Proportional Assessment (COPRAS) are two MCDA methods applied in this paper. Top-fifteen green bonds ranked by specialized media were assessed with the proposed MCDA model. Criteria included the Environmental Performance Index (EPI) proposed by Yale University, and common financial indicators as assets, risks (β), and dividends. The new AHP–COPRAS rank is compared with another published by specialized media.

Measuring farms sustainable innovativeness is a big challenge for both practitioners and academics. The need of sustainable innovativeness assessment in the agricultural business is reasoned in the article. Unfortunately, the features of the farms sustainable innovativeness measurement have not yet been investigated, and any objective methodology for innovativeness assessment is not presented as well. The objective of this article is to find possibility of use some methodology for measuring farm sustainable innovativeness, which would allow ranking farms by this aspect. The article demonstrates the need for multi-criteria method of innovativeness measurement and substantiates the complex proportional assessment method (Copras) as the most appropriate for solution of indicated problem. The model for use of offered method is presented and the practical application of the model is submitted. The final result refuted the opinion that farm innovation depends only on the possibilities to invest funds in a certain area. Indeed, staff creativity and the position of the management regarding certain areas of business make an essential contribution to the sustainable innovativeness level in the agricultural organizations.

Eustachian Tube Dysfunction is considered a common condition among ENT patients and requires careful history, clinical examination and appropriate investigations to obtain a diagnosis. The ETDQ-7 questionnaire is a useful tool to subjectively score severity of symptoms that are related to this pathology (Appendix A). This study aimed to adapt and validate the ETDQ-7 questionnaire in Greece to ensure correct and efficient use in the outpatient setting (Appendix B). The ETDQ-7 was translated into the Greek language following appropriate methodology. Data for the main study were collected from a sample of 75 Greek patients diagnosed with ETD as well as 25 patients that did not have ETD and who served as a control group. The participants completed the adapted ETDQ-7 questionnaire and underwent a clinical examination that was statistically correlated with their ETDQ-7 answers. Face and content validity were confirmed and the questionnaire was found easy to administer and to be completed by our patients. Test-retest reliability revealed similar internal consistency for the questions and good correlation between individual items and total score. Discriminative validity confirmed statistically significant difference between the two patient groups to ensure that the Greek version of ETDQ-7 is useful to confirm the diagnosis. The Greek version of the ETDQ-7 is safe and efficient to use among a variety of investigation methods for the diagnosis of ETD in the Greek speaking population.

Accurately monitoring insecticide resistance in target mosquito populations is important to combating malaria and other vector-borne diseases, and robust methods are key. The “WHO susceptibility bioassay” has been used for +60 years: mosquitoes of known physiological status are exposed to a discriminating concentration of insecticide. Several changes to the test procedures have been made historically which may seem minor but could impact bioassay results. The published test procedures and literature for this method were reviewed for methodological details. Areas where there was room for interpretation in the test procedures or where the test procedures were not being followed were assessed experimentally for impact on bioassay results: covering or uncovering of the tube end during exposure, number of mosquitoes per test unit, and mosquito age. Many publications do not cite the most recent test procedures, methodological details are reported which contradict the test procedures referenced or methodological details are not fully reported. As a result, the precise methodology is unclear. Experimental testing showed that using fewer than the recommended 15-30 mosquitoes per test unit significantly reduced mortality, covering the exposure tube had no effect, and using mosquitoes older than 2-5 days old increased mortality, particularly in the resistant strain. Recommendations are made for better reporting of experimental parameters.

Beginning with the discovery of the BRCA ovarian cancer susceptibility genes and subsequent detailed examination of risk reduction salpingo-oophorectomy (RRSO) specimens, a new paradigm of ovarian carcinogenesis has unfolded with attention to the distal fallopian tube. The primary focus has been an early cancer in the fallopian tube which is seen in virtually all incidentally discovered high-grade serous cancers in asymptomatic women. This high-frequency of tubal involvement in early serous cancer - serous tubal intraepithelial carcinoma or STIC - has galvanized attention to this organ as a primary source of this disease. However, an enduring mystery has been the relatively low frequency of STIC in fallopian tubes of women with advanced malignancy. This paradox, a high-frequency of tubal involvement early and a low-frequency late in the disease process has spurred interest in other potential sources, such as the ovarian surface or secondary Mullerian system. However, because essentially all high-grade serous carcinomas are linked by TP53 mutations, and because fallopian tubes frequently contain early serous proliferations (ESPs) with these mutations, attention has turned to the possibility that nonmalignant but TP53 mutated tubal epithelium could be responsible for an eventual malignancy. Recent data have shown evidence of lineage continuity between ESPs and concurrent serous carcinomas prompting the concept of "precursor escape". This creates a 2nd component of the paradigm by which cells from early lesions can escape the fallopian tube and undergo future malignant transformation later, emerging suddenly as widespread malignancy. This dualistic model thus explains the paradox and opens new questions pertaining to the challenge of both early detection and prevention of this lethal malignancy.

This paper proposes a model to evaluate business projects to get into an incubator, allowing to rank them in order of selection priority. The model combines the Momentum method to build prospective scenarios and the Multiple Criteria Decision Making (MCDM) method TOPSIS-2N to rank the alternatives. Six business projects were evaluated to be incubated. The Momentum method made it possible for us to create an initial core of criteria for the evaluation of incubation projects. The TOPSIS-2N method supported the decision to choose the company to be incubated by ranking the alternatives in order of relevance. Our evaluation model has improved the existing models used by incubators. This model can be used and / or adapted by any incubator to evaluate the business projects to be incubated. The set of criteria for the evaluation of incubation projects is original and the use of prospective scenarios with a MCDM method to evaluate companies to be incubated does not exist in the literature.

Multi-criteria decision analysis (MCDA), one of the prevalent branches of operations research, aims to design mathematical and computational tools for selecting the best alternative among several choices with respect to specific criteria. In the cloud, MCDA based online brokers uses customer specified criteria to rank different service providers. However, subjected to limited domain knowledge, the customer may exclude relevant or include irrelevant criterion, which could result in suboptimal ranking of service providers. To deal with such misspecification, this research proposes a model, which uses notion of factor analysis from the domain of unsupervised machine learning. The model is evaluated using two quality-of-service (QoS) based datasets. The first dataset i.e., feedback from customers, was compiled using leading review websites such as Cloud Hosting Reviews, Best Cloud Computing Providers, and Cloud Storage Reviews and Ratings. The second dataset i.e., feedback from servers, was generated from cloud brokerage architecture that was emulated using high performance computing (HPC) cluster at University of Luxembourg (HPC @ Uni.lu). The simulation runs in a stable cloud environment i.e. when uncertainty is low, shows that online broker (equipped with the proposed model) produces optimized ranking of service providers as compared to other brokers. This is due the fact that proposed model assigns priorities to criteria objectively (using machine learning) rather than using priorities based on subjective judgments of the customer. This research will benefit potential cloud customers that view insufficient domain knowledge as a limiting factor for acquisition of web services in the cloud.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

In the past ten years several novel hantaviruses were discovered in shrews, moles and bats, suggesting the dispersal of hantaviruses in many animal taxa other than rodents during their evolution. Interestingly, the co-evolutionary analyses of most recent studies have raised the possibility of non-rodents may have served as the primordial mammalian host and harboured the ancestors of rodent-borne hantaviruses as well. The aim of our study was to investigate the presence of hantaviruses in bat lung tissue homogenates originally collected for taxonomic purposes in Malaysia, 2015. Hantavirus specific nested RT-PCR screening of 116 samples targeting the L segment of the virus have revealed the positivity of two lung tissue homogenates originating from Murina aenea bat species. Nanopore sequencing of hantavirus positive samples resulted in partial genomic data from S, M and L genome segments. The obtained results indicate the first molecular evidence for hantavirus in Murina aenae bat species and also the first discovery of a hantavirus in Murina bat species. Sequence analysis of the PCR amplicon and partial genome segments suggests the identified virus may represent a novel species in Mobatvirus genus within Hantaviridae family. Furthermore, our results provide additional genomic data to help extend our knowledge about the evolution of these viruses.

The compelling effects of climate change on forests may have been underestimated in the past few decades in practical forestry. Although the first attempts to draw attention to this complex problem appeared almost half a century ago, the debate has been conceptual rather than experimental and applicative. At first glance, the con-cerns were mainly related to sustainable forest management (SFM) issues, which obviously needed attention. Over time, the effects of climate change have been mainly considered in the context of the SFM; they started from various and somewhat different scales and goals. Over time, more research and awareness of the im-portance of SFM under the pressure of climate change have led to the development of a clearer field that can be defined as ‘adaptive forest management’ - to climate change. One of the characteristics of this discipline is to be featured by the absence of univocal methods and / or objectives to be pursued but to identify, verify, and adapt methods to the various climatic and forest types and conditions found in the field. Therefore, this work shows some phases of forest planning and management concepts and criteria over time and recalls some innovative and / or adaptive methods related to the approach to forest planning and management under climate change

The last half of the 20th century was characterized by the most impactful ecosystem changes throughout regulations and guidelines minimalizing environmental harms. Many of them emphasize the importance of enterprise sustainability for renewable energy policy. When dealing with numerous alternatives for the implementation of renewables-based policy, decision-makers need to analyze their impacts on environmental, economic, and social dimensions from a long-term perspective. The aim of this paper is to highlight a challenge to apply the multi-criteria sustainability decision-making framework (MDCA) to mainstream energy policy. The integrative framework covers an approach for the needs of analyzing factors influencing the energy technology selection. In this study, the MDCA-approach combines lifecycle-based methods, Analytical Hierarchy Process, PESTEL (Political, Economic, Social, Technological, Environment and Legal). To demonstrate the applicability and usability of the method three photovoltaic technologies are assessed. The results showed that string ribbon technology is the most sustainable along its life cycle, with a 0.503 sustainability score. The study highlighted the need to embody robust methodologies assessing sustainability-oriented technologies, not used anymore for supporting energy policies. This challenge regarding example evidence can give energy decision-makers a tool to realize their energy policy and in consequence, enhance enterprise sustainability.

This paper aims to investigate the criteria of behaviour of certain type of third order neutral generalized difference equations with distributed delay. With the technique of generalized Riccati transformation and Philos-type method, some oscillation criteria are obtained to ensure convergence and oscillatory solution of suitable example is listed to illustrate the main result.

The practice of spatial econometrics revolves around a weighting matrix, which is often supplied by the user on previous knowledge. This is the so called $\mathbf{W}$ issue. Probably, the aprioristic approach is not the best solution although, nowadays, there few alternatives for the user. Our contribution focuses on the problem of selecting a $\mathbf{W}$ matrix from among a finite set of matrices, all of them considerer appropriate for the case. We develop a new and simple method based on the Entropy corresponding to the distribution of probability estimated for the data. Other alternatives, which are common in current applied work, are also reviewed. The paper includes a large Monte Carlo to calibrate the effectiveness of our approach compared to the others. A well-known case study is also included.

Hydrologic models are conventionally constrained and evaluated using point measurements of streamflow, which represents an aggregated catchment measure. As a consequence of this single objective focus, model parametrization and model parameter sensitivity are typically not reflecting other aspects of catchment behavior. Specifically for distributed models, the spatial pattern aspect is often overlooked. Our paper examines the utility of multiple performance measures in a spatial sensitivity analysis framework to determine the key parameters governing the spatial variability of predicted actual evapotranspiration (AET). Latin hypercube one-at-a-time (LHS-OAT) sampling strategy with multiple initial parameter sets was applied using the mesoscale hydrologic model (mHM) and a total of 17 model parameters were identified as sensitive. The results indicate different parameter sensitivities for different performance measures focusing on temporal hydrograph dynamics and spatial variability of actual evapotranspiration. While spatial patterns were found to be sensitive to vegetation parameters, streamflow dynamics were sensitive to pedo-transfer function (PTF) parameters. Above all, our results show that behavioral model definition based only on streamflow metrics in the generalized likelihood uncertainty estimation (GLUE) type methods require reformulation by incorporating spatial patterns into the definition of threshold values to reveal robust hydrologic behavior in the analysis.

Natural fibers are being increasingly used in different areas of engineering, including as composite reinforcement. Among these fibers, carauá stands out for its good mechanical properties and adherence to resin. Nevertheless, little is known about the behavior of this material in the manufacture of a composite or whether classic failure theory can be used in this case. In this context, the present study assesses the mechanical properties of two laminas made of unidirectional curauá fiber with volumetric fiber percentages of 30 % and 22 %, and compares the results with the values obtained for four failure criteria reported in the literature, using analysis of variance (ANOVA). To that end, tensile tests were conducted in the direction of the fiber and at other loading angles, in addition to iosipescu shear tests. The results show that the maximum stress criterion does not represent the failure behavior of these materials and that the best was the Hashin criterion.

Concrete-filled steel tube (CFST) members have been widely used in the field of civil engineering due to their advanced superior mechanical properties. However, internal defects such as concrete core voids and interface debonding are likely to weaken the load-carrying capacity and stiffness of these members, which affects safety and serviceability of CFST structures. Visualizing the inner defects of concrete core in CFST members have been a critical need in civil engineering construction, a travel time tomography (TTT) is introduced to quantitatively identify and visualize the sizes and positions of CFST members in this paper. Moreover, a parameter analysis is performed to investigate the relationship between TTT imaging qualities and influence factors, e.g. inversion parameters, defect sizes and positions. The effectiveness and accuracy of the TTT algorithm are verified by several numerical examples and the results demonstrate that TTT can identify the sizes and positions of concrete core void defects in CFST members efficiently and several inversion parameters including model weighting matrix and inversion grid size really pose a significant impact on the imaging results of CFST members. In addition, several optimum parameters are recommended to benefit the future study of the promising TTT approach for CFST members.

For effective warehouse management, various criteria should be taken into consideration in terms of inventory management, demand, transportation distance, usage area, delivery-waiting times, and minimizing the costs that may arise from them. Because, the purpose of the product assignment problem is to minimize the total transport distance during storage and to reduce the space required for product assignment. However, the storage location assignment problem (SLAP) occurs simultaneously with production planning activities in real life. In this study, an integrated mixed-integer nonlinear (MINLP) mathematical model is proposed, which includes the assignment of products to storage areas and production planning, using the TOPSIS (Technique for Order Preference by Similarity to Ideal Solution) class based policy for storage systems where multiple criteria are important. In the TOPSIS class-based policy, weight and waiting time criteria are taken into account, as well as the COI (Cube-per-order index index), which is widely used in the literature. In addition, a decision support system flow has been proposed that takes into account the single criterion, multiple criteria and COI index criteria of the developed model and provides its integration with different product assignment policies. Detailed literature research; It has been revealed that the proposed mathematical model and decision support system flow have the feature of applying an existing field of science to a new problem.

The supply of mental health processes in primary care has gaps. This study aims to analyze the association of agreement criteria and flows between primary care teams and the Family Health Support Center (NASF) for mental health collaborative care, considering the difference between capital and non-capital cities in Brazil. This cross-sectional study was conducted based on secondary data from the Primary Care Access and Quality Improvement Program. Agreement criteria and flows were obtained from 3883 NASF teams of the matrix support or collaborative care. The Chi-square test and multiple Poisson regression were used; p &lt; 0.05 was considered statistically significant. Prevalence ratios of negative associations demonstrated protective factors for support actions: follow-up at Psychosocial Care Center, management of psychopharmacotherapy, offer of other therapeutic actions, care process for users of psychoactive substances, and offer of activities to prevent the use of psychoactive substances. Collaborative care in primary care was effective, and capital cities were a protective factor compared with non-capital cities.

Despite achieving over 90% household service coverage, the Latin American and Caribbean region faces energy poverty (EP) challenges, particularly in rural areas. With growing GDP and foreign investments, Panama grapples with significant energy inequality, ranking poorly in clean energy access. Almost 177,000 Panamanians experience energy poverty, impacting their quality of life. This study proposes a Multidimensional Energy Poverty Index for Panama (MEPIP), considering dimensions like lighting, cooking, food refrigeration, thermal comfort, and knowledge/communication. MEPIP, inspired by indicators from Chile, Mexico, and the UK, aims to provide a nuanced understanding of EP. Results from surveyed rural communities, Guásimo, Llano Grande Abajo, Los Aguilares, and La Tranquilla, reveal pervasive energy poverty, emphasizing the urgency of targeted interventions. MEPIP's application identifies critical areas, such as Llano Grande Abajo, highlighting stark inequalities and the need for comprehensive energy policies to address EP in Panama.

The main goal of the study is to assess the Decision criteria, and the determining factor for the sustainability of entrepreneurial startups in order to contribute towards social inclusion and capacity building. Both concepts are in the development phase and are the outcome of entrepreneurial ecosystem and individual behavior and traits. The current study observed the research problem as entrepreneurship and the entrepreneurial startups are the continuous phenomena required for every economy. The lack of an efficient ecosystem and incompetent trait of an entrepreneur drags the entrepreneurial startup to a failure. Therefore, an assessment on decision criteria and determining factors categorizing them with their importance may provide requisites to lead a successful entrepreneurial startup contributing to the social inclusion and capacity building. The study solved the research problem by statistical assessment of decision criteria and determining factors and categorizing them with their importance may provide requisites to lead a successful entrepreneurial startup. The research is built on research questions, objectives, conceptual model, and hypothesis which are tested based on the data collected. The collection of data was done through a survey questionnaire on a sample of established entrepreneurs. The study concludes that five components of decision criteria are Region, Competition, Funding Opportunities, Tax System, and Country Economic Situation, whereas the eight components Consciousness and Reliable, Pursuit Results, Flexibility, Stress Resistance, Skills Identification Exploitation Potential Market Opportunities, Leadership, Creativity and Innovation, and Delegation Decision Making of determining factor are required for a successful entrepreneurial startup to be able to work towards social inclusion and capacity building.

This paper uncovers that quantum uncertain principle makes the single particle with global property have no certain path, and then wave of quantum particle can simultaneously do pass the double slits. The two subwaves after passing Young’s double slits are entanglement, they may form interference of subwaves. Consequently, we find a kind of quantum probabilistic entanglements with Wheeler's delayed choice. Quantum particles such as photons, electrons, neutrons, protons etc mean that wave of the quantum particle can simultaneously do pass through Young's double slits, rather than individual quantum particle may pass through Young's double slits at the same time. When considering wave property, we cannot consider particle property (Just as in the photoelectric effect, considering the particle nature of the system, people cannot consider wave property, otherwise the photoelectric effect cannot appear). Therefore, this paper discovers that the ability of single photon to hit electrons out in photoelectric effect is complementarily equivalent to the ability of wave of the single photon to simultaneously pass through Young's double slits in wave-particle duality. Objective criteria for distinguishing classical and quantum particles are discovered and objectively give the applicable realm of quantum mechanics for the first time. The crisis of the single particle’s simultaneously passing through Young's double slits, which has been plaguing physicists in the whole world up to now for decades, is solved, in which the studies are classified as classical and quantum particles, the classical particle and quantum particle wave cannot and can pass the Young’s slits, respectively. This paper discovers both the new physics mechanism of passing the double slits of the wave with the amplitude of 4-dimensional momentum representation wave function reflecting particle nature and the principle of self-adaptive emergence of wave-particle duality, and then using the principle, this paper gives both direct explanations to the current experiments and new predictions of new some experiments for wave-particle duality. All the deduced results here are consistent with all relevant physics experiments.

China is facing the development requirements of the dual carbon goal and the construction needs of resilient cities. Currently, high-strength composite structural systems are a feasible solution, but their research and application in the construction field are insufficient, especially for the combination forms of concrete above C100 and steel above Q550. In response to this issue, this paper proposes a new high-performance structural system, namely the composite frame - high-strength steel plate wall core tube resilient structure system, which includes high-strength steel plate (Q550) - ultra-high strength concrete (C100) shear walls, replaceable energy dissipation coupling beams, and composite frames. Taking a 200 meter building as an example, this paper designs and establishes calculation models for a conventional reinforced concrete frame-core tube structure and a high-performance structure based on PKPM software, and establishes elastoplastic analysis models for both based on SAUSAGE software, and then conducts dynamic elastoplastic time history analysis and seismic resilience assessment of structures under design basis earthquakes (DBEs), maximum considered earthquake (MCEs) and extremely rare earthquakes (EREs). Research has shown that compared to conventional structures, new high-performance structures can effectively reduce the size of shear walls, reduce the self-weight of the structure, and enhance the space for building use; The story drift ratio has higher redundancy than specification limits, lower plastic damage and overall stiffness degradation of the structure, and better seismic performance; The seismic resilience has significantly improved, especially in the case of casualties, which can better ensure the safety of people's lives and property.