Steam boiler has a significant role in the industrial sector. The failure in boiler tubes significantly reduces the availability of the plant. Furthermore, deposits on the inner tube wall contribute to such failure by changing the thermal resistance of the wall, which causes a significant increase in the tube wall's temperature and, consequently, lower allowable stress. The presented thermal-fluid model is developed for the water tube. The model is implemented using ANSYS FLUENT to estimate the wall maximum water tube wall temperature considering the deposits layer and then determine the minimum thickness of the tube wall via ASME standards to assure safe operation. The model is verified via a mesh independence test. The minimum tube thickness is recommended and justified given the thermo-mechanical performance of the water tubes at several operating loads of 50, 75, and 100 %. These loads are implemented by different convective heat transfer coefficients of flue gases under different deposit thicknesses, thermal conductivity, and flue gas temperature. The present work contributes to the literature by recommending the minimum thickness of the water wall tubes and highlighting the thermo-mechanical effect of the deposits on water tube resilience under different operating conditions.

China is facing the development requirements of the dual carbon goal and the construction needs of resilient cities. Currently, high-strength composite structural systems are a feasible solution, but their research and application in the construction field are insufficient, especially for the combination forms of concrete above C100 and steel above Q550. In response to this issue, this paper proposes a new high-performance structural system, namely the composite frame - high-strength steel plate wall core tube resilient structure system, which includes high-strength steel plate (Q550) - ultra-high strength concrete (C100) shear walls, replaceable energy dissipation coupling beams, and composite frames. Taking a 200 meter building as an example, this paper designs and establishes calculation models for a conventional reinforced concrete frame-core tube structure and a high-performance structure based on PKPM software, and establishes elastoplastic analysis models for both based on SAUSAGE software, and then conducts dynamic elastoplastic time history analysis and seismic resilience assessment of structures under design basis earthquakes (DBEs), maximum considered earthquake (MCEs) and extremely rare earthquakes (EREs). Research has shown that compared to conventional structures, new high-performance structures can effectively reduce the size of shear walls, reduce the self-weight of the structure, and enhance the space for building use; The story drift ratio has higher redundancy than specification limits, lower plastic damage and overall stiffness degradation of the structure, and better seismic performance; The seismic resilience has significantly improved, especially in the case of casualties, which can better ensure the safety of people's lives and property.

The problem of simulating wakes in a stratified oceanic environment with active background turbulence is considered. Anisotropic RANS turbulence models are tested against laboratory and eddy-resolving models of the problem. An important aspect of our work is to acknowledge that the environment is not quiescent; therefore, additional sources are included in the models to provide a non-zero background turbulence. The RANS models are found to reproduce some key features from the eddy-resolving and laboratory descriptions of the problem. Tests using the freestream sources show the intuitive result that background turbulence causes more rapid wake growth and decay.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

The genetic heterogeneity of autism has stymied the search for causes and cures. Whole-genomic studies on large numbers of families have helped identify combinations of inherited and de novo signal. In the present work, we re-analyze DNA microarrays using a novel strategy that takes prior knowledge of genetic relationships into account and that was designed to boost signal important to our understanding of the molecular basis of autism. Our strategy was designed to identify significant genomic variation within a priori defined biological concepts and improves signal detection while lessening the severity of multiple test correction seen in standard analysis of genome-wide association data. Upon application of our approach using 3,244 biological concepts, we detected genomic variation in 68 biological concepts with significant association to autism in comparison to family-based controls. These concepts clustered naturally into a total of 19 classes, principally including cell adhesion, cancer, and immune response. The top-ranking concepts contained high percentages of genes already suspected to play roles in autism or in a related neurological disorder. In addition, many of the sets associated with autism at the DNA level also proved to be predictive of changes in gene expression within a separate population of autistic cases, suggesting that the signature of genomic variation may also be detectable in blood-based transcriptional profiles. This cross-validation with gene expression data from individuals with autism coupled with the enrichment within autism-related neurological disorders supported the possibility that the mutations play important roles in the onset of autism and should be given priority for further study. Our work provides new leads into the genetic underpinnings of autism and highlights the importance of reanalysis of genomic studies of complex disease using prior knowledge of genetic organization.

Expansion tube is ideal energy absorber which dissipates kinetic energy through plastic deformation and friction. There is an urgent need to understand the influence of key parameter, e.g. semi angle, tube material, and friction coefficient, on the mechanical response and energy absorption characteristics of expansion tube. In the present work, the material properties of the tubes were tested under quasi-static loading condition, and the numerical simulations were carried out by using commercial software ABAQUS. Based on the validated finite element simulation, all the semi angle, tube material, and friction have significant effects on the energy absorption capacity of expansion tube. The expansion tube with high tensile stress of parent material have high energy absorption capacity, while the specific energy absorption is linear with the tensile stress/density of tube material. This work would give a guidance to the structural design and parent materials selection for expansion tubes.

We presented unusual case of double left ventricular false aneurysm complicating late presentation AMI successfully treated with the combination of urgent surgical drainage of tamponade, staged PCI of non-culprit lesion, preventive implantation of ICD-DR, guideline directed heart failure medical therapy and delayed but effective reconstructive operation.

Aboriginal Australians have a fundamental human right to opportunities that lead to healthy and flourishing lives. While the impact of trauma on Aboriginal Australians is well-documented, a pervasive deficit narrative that focuses on problems and pathology persists in research and policy discourse. This narrative risks further exacerbating Aboriginal disadvantage, through a focus on ‘fixing what is wrong’ with Aboriginal Australians, and the internalising of these narratives by Aboriginal Australians. While a growing body of research adopts strength-based models, limited research has sought to explore Aboriginal flourishing. This conceptual paper seeks to contribute to a burgeoning paradigm shift in Aboriginal research, seeking to understand what can be learned from Aboriginal people who flourish, how we best determine this, and in what contexts this can be impactful. Within, we argue the case for a new approach to exploring Aboriginal wellbeing that integrates salutogenic, positive psychology concepts with complex systems theory to understand and promote Aboriginal wellbeing and flourishing, While deeper work may be required to establish the parameters of a strength-based, culturally aligned Aboriginal conceptualisation of positive psychology, we suggest the integration of Aboriginal and Western methodologies offer unique and potent means of shifting the dial on seemingly intractable problems.

Background: Functional restoration of abdominal wall defects represent one of the fundamental challenges of reconstructive surgery. Synthetic grafts or crosslinked animal-derived biological grafts are characterized by significant adverse reactions, which are mostly observed after their implantation. The aim of this study was to evaluate the efficacy of the decellularization protocol to produce a completely acellular full-thickness abdominal wall scaffold. Methods: Full-thickness abdominal wall samples were harvested from Wistar rats and submitted to a 3 cylce decellularization process. Histological, biochemical and DNA quantification analyses were applied to evaluate the effect of the decellularization protocol. Mechanical testing and immunogenicity assessment were also performed. Results: Histological, biochemical and DNA analysis results showed the efficient decellularization abdominal wall samples after the 3rd cycle. Decellularized abdominal wall scaffolds were characterized by good biochemical and mechanical properties Conclusion: The data presented herein confirm the effective production of rat-derived full-thickness abdominal wall scaffold. Expanding this approach will allow the exploitation of the capacity of the proposed decellularization protocol in producing acellular abdominal wall scaffolds from larger animal models or human cadaveric donors. In this way, the utility of biological scaffolds with preserved in vivo remodelling properties may be one step closer to its application in clinical studies.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

The microbiome gut brain (MGB) axis involves bidirectional routes of communication and has emerged as a potential therapeutic target for multiple medical specialities including psychiatry. Significant numbers of preclinical trials have taken place with some transitioning to clinical studies in more recent years. Some positive results have been reported secondary to probiotic administration in both healthy populations and specific patient groups. This review aims to summarise the current understanding of the MGB axis and the preclinical and clinical findings relevant to psychiatry. The link between the gut microbiome and irritable bowel syndrome (IBS) is well established. Significant differences have been identified between the microbiome of patients with a diagnosis of depressive disorder and healthy controls. Similar findings have occurred in patients diagnosed with bipolar affective disorder. A probiotic containing Lactobacillus acidophilus, Lactobacillus casei, and Bifidobacterium bifidum produced clinically measurable symptom improvement in patients with depressive disorder. To date some promising results have suggested that probiotics could play a role in the treatment of stress-related psychiatric disease. However, more well-controlled clinical trials are required to determine which clinical conditions are likely to benefit most significantly from this novel approach.

We aimed to determine whether A-mode ultrasound (US) can provide accurate and reliable measurements comparable to those obtained through B-mode US, under diverse conditions. Thirty healthy participants (15 female, 15 male) underwent measurements of subcutaneous fat thickness (SFT), muscle thickness (MT), and muscle quality (MQ) in the trapezius and biceps brachii muscle with both US modes after and before exercises designed to stimulate the respec-tive muscles. In three key indices, the results demonstrated high validity of A-mode, with min-imal mean differences between the two devices less than 0.91mm and intraclass correlation coef-ficients exceeding 0.95 at all measures. Also, Correlation coefficients between error scores and average scores for the trapezius and biceps brachii muscles suggested no evidence of systematic error. The trapezius MT and MQ significantly increased, and biceps brachii MT significantly in-creased after exercise (p<0.05). Notably, both A-mode and B-mode exhibited the same tendency in these post-exercise changes in muscle. This study suggests that low-cost and low-resolution A-mode US provides measurements of SFT, MT, and MQ similar to more expensive, high-resolution B-mode imaging. A-mode US can serve as an affordable and portable alternative for muscle assessment.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

In pediatric burn care, achieving swift healing with minimal complications remains paramount. This investigation assesses polyhexamethylene biguanide (PHMB)'s role in managing superficial partial-thickness burns in children, focusing on the effects of various patient-specific factors on recovery. Through a retrospective analysis of 27 pediatric cases treated with PHMB, we explored the impact of age, burn size, dressing frequency, treatment delay, cold therapy application, and analgesic usage on the duration until reepithelialization. Notably, the majority of patients benefited from early cold therapy, yet only 1 in 3 patients received analgesics. The study reveals a mean healing time of 8.78 days, with the extent of the burn showing a strong correlation to recovery speed. Most treatments were managed outpatient, evidenced by a negligible average hospital stay. Impressively, the intervention recorded no complications. Our findings endorse PHMB as a promising treatment for second-degree burns in young patients, offering healing efficiency on par with or surpassing traditional methods, without increasing complication risks. This investigation underscores the necessity for continued exploration into the optimal application of prehospital interventions and the comprehensive benefits of PHMB in pediatric burn management, advocating for future research aimed at assessing long-term outcomes, including scar quality and patient satisfaction.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

: Background: Overweight and obesity are major risk factors for many chronic diseases, and weight-loss interventions often include systematic exercising and nutritional supplements. The purpose of this study was to determine the independent/synergistic effects of Spirulina maxima supplementation (6-week, 4.5 g/day) and a systematic physical exercise program (6 weeks/ 2 times) on body composition and cardiorespiratory fitness of overweight and obese subjects. Methods: 27 overweight and 25 obese sedentary male subjects were assigned to four interventions through a randomized double-blind, crossover controlled trial: Physical exercise program with (SE) or without (Ex) Spirulina maxima or no-exercise program with (Sm) and without (C) Spirulina maxima. Body composition and cardiorespiratory fitness parameters were taken during a maximal intensity test. Results: As compared to C group, SE, Sm and Ex groups reduced (p < 0.05) their body fat percentage while improving their maximal oxygen uptake (VO₂max; r = −0.40), being obese subjects more benefited. Weight loss, time to reach fatigue and onset of blood lactate accumulation were improved in both Spirulina maxima supplemented groups, regardless the subjects’ body composition. Conclusions: Spirulina maxima supplementation synergistically improves the effects of systematic exercise in body composition and cardiorespiratory fitness parameters in overweight but mostly in obese adults.

An effort was made to find a relationship between the ratio of average asperities height and lubricant thickness at the point of contact of rolling element ball bearings, and empirical equations to predict the life for bearings under constant motion. Two independent failure mechanisms were considered, fatigue failure and lubricant failure resulting in seizing of the roller bearing. A theoretical formula for both of these methods was established for the combined probability of failure using both of these failure mechanisms. Fatigue failure was modeled with the empirical equations of Lundberg and Palmgren and standardized in DIN/ISO281. The seizure failure, which this effort sought to investigate, was predicted using Greenwood and Williamson's theories on surface roughness and asperities during lubricated contact. These two mechanisms were combined, and compared to predicted cycle lives of commercial roller bearing, and a clear correlation was demonstrated. This effort demonstrated that the Greenwood-Williams theories on the relative height of asperities versus lubricant film thickness can be used to predict the probability of a lubricant failure resulting in a roller bearing seizing during use.

An effort was made to find a relationship between the predicted tribological conditions at the point of contact of ball bearings, and empirical equations to predict the life for bearings under constant motion. The model was modified to predict the temperature dependence, and compare rapid accelerations and decelerations with empirical extrapolations.

This review is a first attempt at bringing together various concepts from research on wall- and magnetically-bounded turbulent flows. Brief reviews of both fields are provided: The main similarities identified are coherent (turbulent) structures, flow generation and transport barriers. Examples are provided and discussed.

Relationships between drought and fire danger indices are examined to 1) incorporate fire risk information into the National Integrated Drought Information System California-Nevada Drought Early Warning System and 2) provide a baseline analysis for application of drought indices into a fire risk management framework. We analyzed four drought indices that incorporate precipitation and evaporative demand (E₀) and three fire indices that reflect fuel moisture and potential fire intensity. Seasonally averaged fire danger indices were most strongly correlated to multi-scalar drought indices that use E₀ (the Evaporative Demand Drought Index [EDDI] and Standardized Precipitation Evapotranspiration Index [SPEI]) at approximately annual time scales that reflect buildup of antecedent drought conditions. Results indicate that EDDI and SPEI can inform seasonal fire potential outlooks at the beginning of summer. An E₀ decomposition case study of conditions prior to the Tubbs Fire in Northern California indicate high E₀ (97th percentile) driven predominantly by low humidity signaled increased fire potential several days before the start of the fire. Initial use of EDDI by fire management groups during summer and fall 2018 highlights several value-added applications, including seasonal fire potential outlooks, funding fire severity level requests, and assessing set-up conditions prior to large, explosive fire cases.

A membrane ozonation contactor was built to investigate ozonation using tubular membranes and to inform computational fluid dynamics (CFD) studies. Non-porous tubular polydimethylsiloxane (PDMS) membranes of 1.0 – 3.2 mm inner diameter were tested at ozone gas concentrations of 110 – 200 g m−3 and liquid side velocities of 0.002 m s−1 – 0.226 m s−1. The dissolved ozone concentration could be adjusted to up to 14 mg O3 L−1 and increased with decreasing membrane diameter and liquid side velocity. Experimental mass transfer coefficients and molar fluxes of ozone were 1.1∙10−5 mol m−2 s−1 and 2.4∙10−6 m s−1, respectively, for the smallest membrane. CFD modelling could predict the final ozone concentrations but slightly overestimated mass transfer coefficients and molar fluxes of ozone. Model contaminant degradation experiments and UV absorption measurements of ozonated water samples in both ozone (O3) and peroxone (H2O2/O3) reaction systems in pure water, river water, wastewater effluent and solutions containing humic acid show that the contactor system can be used to generate information on the reactivity of ozone with different water matrices. Combining simple membrane contactors with CFD allows predicting ozonation performance under a variety of conditions leading to improved bubble-less ozone systems for water treatment.

A three-dimensional vector field model is proposed, whose dimensions are the Hansen Solubility Parameters: dispersion parameter (δD), polarity parameter (δP), and hydrogen bonding parameter (δH). The vector space that defines the field has the peculiarity of having the dispersion vector with a magnitude of 2, as its base vector, while polarity and hydrogen bonding vectors have a magnitude of 1. A substance is characterised as a position vector, and the interaction between two substances is determined by calculating the vector difference of both, known as the interaction vector. Interaction among substances may involve solubility, swelling, cracking, surface tension, interface tension, and any physical phenomena where intermolecular energies of dispersion, polarity or hydrogen bonding come into play. This paper studies free surface energy (surface and interfacial tension). It has been found that free surface energy is directly proportional to the square of the magnitude of the interaction vector. The proportionality constant, τ, is expressed in length units, has a value of 0.025 nm, and does not depend on the chemical nature of the substance or state of matter (solid, liquid or gas). Constant value τ appears universal and aligns with the thickness of interfaces, thereby supporting Guggenheim's hypothesis. This hypothesis asserts that interfaces possess actual thickness and are not merely mathematical surfaces, as originally postulated by Gibbs. Moreover, it also has been found that interface thickness, τ, is approximately equal to half of the Bohr radius, a0, which is defined by universal constants. Because the solubility parameters of thousands of substances are known and can be easily determined from molecular structure, a good approximation of the surface and interfacial tension of any given substance can now be calculated. It has also been found that contact angles of sessile droplets in three-phased systems can be calculated from the interaction vectors of the implicated substances.

Spacetime torsion is known to be highly suppressed at the end of inflation, called preheating. Of course this fact does not avoid that metric could affect the cosmic dynamos at preheating phase as was showed by Bassett et al, in the general relativity (GR) case. In this paper, is to show that a torsionful magnetogenesis in QED effective lagrangean, drives either a torsion damping or an amplification mechanism or dynamo effect, depending upon torsion chirality. The present extension of Basset et al theory yields a new magnetic field expression $B\sim{a^{(1\pm{\beta})}}$, obtained from dynamo equation in QED. Here a cosmic factor ${\beta}=g_{T}{\eta}k$ is present. In a second example we find Higgs inlationary fields in Einstein-Cartan gravity thick domain walls (DWs). Recently a moodified Einstein-Cartan gravity was given by M Shaposhnikov et al [PRL (2020)] to obtain higgs like inflatons as a portal to dark energy.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

In this paper is proposed an analytical technique which can be used to obtain the forced response of a cantilevered tube conveying fluid. Considering the pipe subjected to an arbitrary harmonic force either distributed or concentrated, an analytical solution is found using Green’s function method. The solution obtained of the closed form satisfies the differential equations in a classical sense. The presented method giving the exact solutions is more precise than the classical eigenfunction expansion or Galerkin’s method with no need to the eigenfunctions or eigenvalues.

The study of ecosystems, both natural and artificial, has historically been mediated by population dynamics theories. In this framework, quantifying population numbers and related variables (associated with metabolism or biological-environmental interactions) plays a central role in measuring and predicting system-level properties. As we move towards advanced technological engineering of cells and organisms, the possibility of bioengineering ecosystems (from the gut microbiome to wildlands) opens several questions that will require quantitative models to find answers. Here, we present a comprehensive survey of quantitative modelling approaches for managing three kinds of synthetic ecosystems, sharing the presence of engineered strains. These include test tube examples of ecosystems hosting a relatively low number of interacting species, mesoscale closed ecosystems (or ecospheres), and macro-scale, engineered ecosystems. The potential outcomes of synthetic ecosystem designs and their limits will be relevant to different disciplines, including biomedical engineering, astrobiology, space exploration and fighting climate change impacts on endangered ecosystems. We propose a space of possible ecosystems that captures this broad range of scenarios and a tentative road map for open problems and further exploration.

The Brazilian livestock is predominantly extensive, with approximately 90% of the production being sustained on pasture, which occupies around 20% of the territory. In the current climate change scenario and where cropland is becoming a limited resource, there is a growing need for a more efficient land use and occupation. It is estimated that more than half of the Brazilian pastures have some level of degradation; however there is still no mapping of the quality of pastures on a national scale. In this study, we mapped and evaluated the spatio-temporal dynamics of pasture quality in Brazil, between 2010 and 2018, considering three classes of degradation: Absent (D0), Intermediate (D1), and Severe (D2). There was no variation in the total area occupied by pastures in the evaluated period, in spite of the accentuated spatial dynamics, with a retraction in the center-south and expansion to the north, over areas of ​​native vegetation. The percentage of non-degraded pastures increased ~12%, due to the recovery of degraded areas and the emergence of new pasture areas as a result of the prevailing spatial dynamics. However, about 44 Mha of the pasture area is currently severely degraded. The dynamics in pasture quality were not homogeneous in property size classes. We observed that in the approximately 2.68 million properties with livestock activity, the proportion with quality gains was twice as low in small properties compared to large ones, and the proportion with losses was three times greater, showing an increase in inequality between properties with more and less resources (large and small, respectively). The areas occupied by pastures in Brazil present an unique opportunity to increase livestock production and make available areas for agriculture, without the need for new deforestation in the coming decades.

Controlling the concentration of free radicals in polymerization systems is advantageous for preparing cationic polyacrylamide (CPAM) with high molecular weight and acceptable dissolvability. In this study, a novel ultraviolet (UV)-initiated system characterized with adjustable light intensity and redox-azo complex initiator was used to synthesize a CPAM flocculant named NP. Comparatively, another CPAM flocculant named SP with stable UV light intensity and single initiator was prepared. The chemical structure, morphology, and thermal stability were analyzed through instrumental analysis. Proton nuclear magnetic resonance indicated that NP was successfully prepared, and a small fraction of cationic homopolymer was mixed in the product. Polymerization conditions were optimized, and polymerization mechanism was determined by investigating the effects of various parameters on intrinsic viscosity, conversion, and dissolvability. Results showed that the best performance was obtained at indexes of 0.45 wt‰ redox initiator concentration, 0.2 wt‰ azo initiator concentration, 40.0 wt% of cationic monomer, first- and second-stage light intensities of 8.5 and 13 mW/cm², respectively, and 3 wt% urea. Sludge conditioning performances of NP and SP were comparatively evaluated, and the mechanism was determined by investigating the sedimentation behavior and floc size distribution. High intrinsic viscosity, porous morphology structure, and the mixed cationic homopolymer of NP resulted in better sludge conditioning performance.

The organic solar cells (OSCs) have drawn attention in the past decade due to its cynosure in industrial manufacturing because of its promising properties such as low weight, highly flexible and low cost production. However, low η restricts the utilization of OSCs for potential application such as low cost energy harvesting devices. In this paper, OSCs structure based on triple junction tandem scheme is reported with three different absorber materials with the objective to enhance the absorption of photons which in turn improves the η, as well as its correlating performance parameters. The investigated structure gives the higher value of η = 14.33% with Jsc=16.87 (mA/m2), Voc=1.0 (V), and FF=84.97% by utilizing a stack of three different absorber layers with different band energies. The proposed structure is tested under 1.5 (AM) with 1 sun (W/m2). The impact of top, middle and bottom sub cells thickness on η is analyzed with a terse to find the optimum thickness for three sub cells to extract high η. The optimized structure is then tested with different electrode combination and the highest η is recorded with FTO/Ag. Moreover, the influence of upsurge temperature is also demonstrated on the proposed structure and observed that the upsurge temperature has greatly affected the electrical parameters of the device and η decreases from 14.33% to 11.40% when the temperature of the device rises from 300-400 K.

The sugar company Valdez S.A. Entity located within the geographical limits of the city of Milagro, needs to reduce its emissions to the environment and does not always comply with the air emissions standards for stationary combustion sources, which indicates that for equipment installed before 2003 they have a maximum limit of 300 mg / m³. A mist eliminator was designed to work inside the original wet gas scrubber of the water-tube cauldron #10, which uses Bagasse as fuel, for the generation of steam for industrial use. The research is documentary and field. The methodology used was mixed. focusing on the comparison of three types of technologies to meet the objectives, the fog eliminators types: Demister, Cyclone and Chevron. To find the appropriate complement, a comparison sheet was made, which is a table of contents evaluated quantitatively, analyzing indicators formulated in each of the contents. The results, supported by the Multiple Criteria Decision Analysis methodology, select the Chevron type fog eliminator, with the best efficiency for capture. Using AutoCAD, allows to visualize in 3D, the structural design in the gas scrubber.

The idea that the Earth system self-regulates in a habitable state was proposed in the 1970s by James Lovelock, who conjectured that life plays a self-regulatory role on a planetary-level scale. A formal approach to such hypothesis was presented afterwards under a toy model known as the Daisyworld. The model showed how such life-geosphere homeostasis was an emergent property of the system, where two species with different properties adjusted their populations to the changing external environment. So far, this ideal world exists only as a mathematical or computational construct, but it would be desirable to have a real, biological implementation of Lovelock's picture beyond our one Biosphere. Inspired in the exploration of synthetic ecosystems using genetic engineering and recent cell factory designs, here we propose such a living, microbial Daisyworld. This is based on a synthetic microbial ecosystem using pH as the external, abiotic control parameter. Several case studies are considering, including two, three and multiple species assemblies. Despite that oscillatory dynamics and chaos emerge in the latter case, it is shown that global regulation is also achieved in most cases as species diversity increases. The alternative implementations and their implications of this model in other synthetic biology scenarios, including ecosystem engineering, are outlined.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

The envelope (façade) of a building is the first barrier between the exterior and the interior of the building and withstands the highest variation of temperature and solar radiation. Trombe walls are used to take advantage of that and contribute to the heating of interior air, helping the heating system. In this study, a new Trombe wall design is presented with the aim to contribute significantly to the ventilation of residential buildings. For this an exterior wall equipped with a proposed Trombe system was studied in a numerical simulation analysis. The proposed systems consist of two parts, the air cavities on the exterior of the wall, covered with silica glass, and another layer used for heat transfer, on the interior, comprised of a MPCLBs wall of 115mm. Two cities in Romania were considered to represent the coldest and hottest climate in Romania. Brașov representing the cold climate and Constanța representing the hot climate. In the investigation, both the presence and absence of solar radiation were taken into account. In total 4 cases were established. For all four cases monthly research was made using monthly means temperature, direct and diffuse solar radiation. The results are promising and illustrate that the system works the best during the transitional seasons of spring and autumn. The lower the outdoor temperature the higher the temperature can be increased. Overall, solar radiation accounted for an average of 2 °C increase. The temperature increase varied between 3.4 °C to 15.99 °C for Brașov and between 6.42 °C to 12.07 °C in Constanța.

Free-living terrestrial mites (Acari) have persisted through numerous glacial cycles in Antarctica. Very little is known, however, of their genetic diversity and distribution, particularly within the Ross Sea region. To redress this gap, we sampled for mites throughout the Ross Sea region, East Antarctica, including Victoria Land and the Queen Maud Mountains (QMM), covering a latitudinal range of 72-85oS, as well as from Lauft Island near Mt Siple (73oS) in West Antarctica and Macquarie Island (54oS) in the sub-Antarctic. We assessed genetic diversity using mitochondrial cytochrome c oxidase subunit I gene sequences (COI-5P DNA barcode region), and also morphologically identified voucher specimens. We obtained 130 sequences representing four genera: Nanorchestes (n = 30 sequences), Stereotydeus (n = 46), Coccorhagidia (n = 18) and Eupodes (n = 36). Tree-based analyses (maximum likelihood) revealed 13 genetic clusters, representing as many as 23 putative species indicated by Barcode Index Numbers (BINs) from the Barcode of Life Datasystems (BOLD) database. We found evidence for geographically-isolated cryptic species, e.g. within Stereotydeus belli and S. punctatus, as well as unique genetic groups occurring in sympatry (e.g. Nanorchestes spp. in QMM). Collectively, these data confirm high genetic divergence as a consequence of geographic isolation over evolutionary timescales. From a conservation perspective, additional targeted sampling of understudied areas in the Ross Sea region should be prioritised, as further diversity is likely to be found for these short-range endemic mites.

The purpose of the present study was to examine the relationships between bat swing speed (BSS) and muscle thickness and lateral asymmetry of the trunk and limbs in collegiate baseball players. Twenty-four collegiate baseball players participated in this study. The maximum BSS in hitting a teed ball was measured using a motion capture system. The muscle thicknesses of the trunk (upper abdominal rectus, central abdominal rectus, lower abdominal rectus, abdominal wall, and multifidus lumborum), upper limb, and lower limb were measured using a B-mode ultrasonography. Lateral asymmetry between each pair of muscles was determined as the ratio of the thickness of the dominant side to that of the non-dominant side. Significant positive correlations were observed between BSS and muscle thicknesses of the abdominal wall and multifidus lumborum on the dominant side (r = 0.426 and 0.431, respectively; p < 0.05), while nearly significant positive correlations were observed between BSS and muscle thicknesses on the non-dominant side. No significant correlations were found between BSS and lateral asymmetry of all muscles. These findings indicate the importance of the trunk muscles for bat swing, and the lack of association between BSS and lateral asymmetry of muscle size.

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

In this study, the efficiencies of flat-plate and U-tube solar collectors were investigated experimentally when an Al₂O₃ nanofluid was used as a working fluid and compared to those of solar collectors using water. The energy saving and CO₂ and SO₂ generated were calculated and compared to those of solar collectors using water. In addition, based on the experimental results, an economic analysis of the use of solar collectors in various countries was performed. As the concentration of the Al₂O₃ nanofluid increased, the performance of the solar collector improved. The highest efficiency for the solar collectors was shown at the concentration of 1.0 vol% with the nanoparticle size of 20 nm. The maximum efficiencies of the flat-plate and U-tube solar collectors using 1.0 vol%-Al₂O₃ nanofluid with 20-nm nanoparticles was 74.9% and 72.4%, respectively, when the heat loss parameter was zero. The efficiencies of the flat-plate and U-tube solar collectors using Al₂O₃ nanofluid were 14.8% and 10.7 higher, respectively, than those using water. When 50 EA flat-plate solar collectors were operated for one year using Al₂O₃ nanofluid, the coal use, generated CO₂, and generated SO₂ were 189.99 kg, 556.69 kg, and 2.03 kg less than those of solar collectors using water, respectively. In addition, the largest electricity cost reduction was in Germany.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil &amp; gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

A heat transfer model, has determined millimeter crude oil thicknesses on saltwater at night. Model inputs are calibrated thermographic imagery, weather station data, metrological observations, and crude oil thermal conductivity. Outdoor field-testing was performed at the National Oil Spill Response & Renewable Energy Test Facility (Ohmsett) to determine model accuracy. Alaskan North Slope (ANS), Hoover Offshore Oil Pipeline System Blend (HOOPS), and ROCK crude oils were placed at varying mm depths. A roof-top mounted thermal camera measured the average oil surface temperature for each target and converted to oil spill thickness. The fidelity of the thickness measurements is dependent on the accurate measurement of the atmospheric and weather parameters, sea state, heat transfer constants, crude oil evaporation rates, and calibration and stability of the thermal camera.

The steady state tube furnace (SSTF) (ISO/TS 19700) was used to assess the effects altering the reaction zone of a flame had on smoke toxicity measurements. The gas inlet of the apparatus was modified to allow for a mixture of nitrogen and air to be introduced into the system. The volume of air used in each test remained at 2 L min-1 , and additional volumes of nitrogen were varied between tests altering the total volume of gas used in the primary gas inlet. The chosen conditions were representative of under-ventilated flaming by using a restricted oxygen environment. The research shows that the increase in volume flow of gas over a sample increased the smoke toxicity of the materials tested (CO and HCN). When increasing the volume of the primary air-flow through the tube furnace, the flow causes thinning of the flame zone in the apparatus and results in gaseous species spending less time in the reaction zone, resulting in less time available for chemical reactions to occur. This resulted in less complete combustion occurring, and hence an increased yield of measured products of incomplete combustion (CO and HCN), and a decreased yield of products of complete combustion (CO2).

. The impedance change of an induction coil surrounding a metal tube adapter is investigated by the truncated region eigenfunction expansion (TREE) method. Conventional TREE method is inapplicable to this problem as a consequence of the numerical overflow of eigenfunctions of the air-metal multi-subdomain regions. The difficulty is surmounted by a normalization procedure for the numerical eigenfunctions obtained from the finite element method (FEM). Efficient algorithm is devised by the Clenshaw-Curtis quadrature rule for integrals involving the numerical eigenfunctions. Numerical results of the TREE and FEM simulation coincide very well in all cases, and the efficiency of the proposed method is also confirmed.

Piriform fossa and/or esophageal injuries caused by calibration tubes are relatively rare and re-main unelucidated. Herein, we report the case of a 36-year-old woman with morbid obesity, sleep apnea, and menstrual abnormalities who was scheduled to undergo laparoscopic sleeve gastrectomy (LSG). We inserted a 36-Fr Nelaton catheter made of natural rubber as a calibration tube during the surgery. However, excessive resistance was observed. We confirmed a submuco-sal layer detachment of approximately 5 cm from the left piriform fossa to the esophagus using intraoperative endoscopy. Additionally, LSG was performed using an endoscope as the guiding calibration tube. We inserted a nasogastric tube under endoscopy with a guidewire before com-pleting the surgery, hoping for a guiding effect on saliva flow. After 17 months, the patient suc-cessfully lost weight postoperatively without complaints of neck pain or discomfort during swallowing. Therefore, if the damage is limited to the submucosal layer, as in this case, conserva-tive therapy should be considered, which is similar to the concept of not requiring suture closure in endoscopic submucosal dissection. This case highlights the risk of iatrogenic injuries to the pi-riform fossa and/or esophagus during LSG and the importance of careful calibration tube inser-tion to prevent them.

Liquid manipulation by photoisomerization attracts recent attentions as a new active droplet control method for micro-chemical analysis. Such a non-inverse manipulation can be realized by a use of solution liquid of surfactant that exhibits the \emph{cis}-\emph{trans} isomerization triggered by light irradiation with a specific wavelength such as ultraviolet light. Since the isomerization is accompanied by changes in fluid properties, a light irradiation on one of liquid-air interfaces of a liquid column in a tube would generate differences in the wettability accompanied between the both sides of the finite liquid column. Although this technique has been demonstrated experimentally by Muto et al. (\emph{Euro.~Phys.~J.~Special Topics}, {\bf 226}, 2016, 1199--1205), its dynamics and developments of each isomer distribution are not understood. In order to reveal the liquid-column migration phenomenon, we have performed numerical simulations of air-liquid two-phase flows and its scalar transport of the isomer, using the Volume-of-Fluid method in conjunction with the Continuum-Surface-Force model and Continuous-Species-Transfer method. We validated present results by comparison with experimental result in terms of the migration distance of the liquid column. We confirmed a termination of the liquid-column migration occurs when the \emph{cis} isomer distribution reaches the non-irradiated region. The migration speed was less dependent on the liquid-column length and was proportional to the tube diameter.

This study was to explore the effects of glabridin and gymnemic acid on the structural changes of the choroidal layer as well as the expression of VEGF and CD31 in diabetic rats. The animals were separated into five groups: the control group (C), the diabetic group (DM), the diabetic rats treated with glabridin 40 mg/kg body weight (DM+GB), the diabetic rats treated with gymnemic acid 400 mg/kg body weight (DM+GM), and the diabetic rats treated with glyburide 4 mg/kg body weight (DM+GR). There has been an increase in the thickness of both the choroid layer and the wall of the arteries in the diabetic group. A decrease in vascularity and choroidal neovascularization can be found in DM rats. After eight weeks of experimentation, the choroidal thickness and wall of choroid arteries, as well as the diameter of the lumen of choroid arteries in the DM+GB, DM+GM, and DM+GR groups, had improved. The expression of VEGF and CD31 was lower compared to the DM group. According to the findings of the current research, glabridin and gymnemic acid can improve and reduce the damage to the choroid, which is a factor that can sometimes result in vision loss.

The research field of two dimensional (2D) materials strongly relies on optical microscopy characterization tools to identify atomically thin materials and to determine their number of layers. Moreover, optical microscopy-based techniques also opened the door to study the optical properties of these nanomaterials. We present a comprehensive study of the differential reflectance spectra of 2D semiconducting transition metal dichalcogenides (TMDCs), MoS₂, MoSe₂, WS₂ and WSe₂, with thickness ranging from one layer up to six layers. We analyze the thickness-dependent energy of the different excitonic features, indicating the change in the band structure of the different TMDC materials with the number of layers. Our work provides a route to employ differential reflectance spectroscopy for determining the number of layers of MoS₂, MoSe₂, WS₂ and WSe₂.

We have performed first-principles calculations to study the interfacial exchange coupling and magnetocrystalline anisotropy (MCA) energy in a SmCo₅/Sm₂Co₁₇ multilayer model systems. The phase of SmCo₅ and Sm₂Co₁₇ stacking along (0001) direction are structurally well matched. The atomic structure, including the alignment and the separation between layers, were firstly optimized. Then the non-collinear magnetic structures were calculated to explore the exchange coupling across the interface and the variation of MCA energy. We found that the inter-phase exchange coupling strength, rotating behavior and MCA energy are strongly dependent on the atomic thickness of the SmCo₅ and Sm₂Co₁₇ phase.

The purpose of this study is to propose a consecutive manufacturing process system to secure the productivity of excellent STKN540B steel tube in the respect of economy and safety as the supporting material for mega structures such as building, bridge and ship. The components of consecutive manufacturing are press-bending, orbital auto welding and steel tube correction. By using STKN540B a high-strength steel material with low yield point that requires a special manufacturing process unlike other steel materials, an actual tube manufacturing is carried out at each stage in this experimental study. With this, the quality of steel tube and the efficiency of the manufacturing process are analyzed to draw out some points to improve in the future.

In order to improve the performance of the draft tube in hydraulic turbine, a multi–objective optimization method for the draft tube is developed by combining the design of experiment (DOE), the radial basis function (RBF) and the non–dominated sorting genetic algorithm (NSGA–II) in this paper. The geometrical design variables of the median section in the draft tube and the cross section in its exit diffuser are considered as design parameters in this optimization, which objective function is to maximize the pressure recovery factor (Cp) and minimize the energy loss coefficient (ζ). The limited numbers of design matrix required for the shape optimization of the draft tube is generated by optimal Latin hypercube (OLH) method of the DOE technique, of which performances are evaluated through computational fluid dynamic (CFD) numerical simulation. For reducing of the computational consumption, the approximate model is used based on the RBF. The Pareto optimal solutions are finally performed using the NSGA–II for obtaining the best geometrical parameters of the draft tube. The optimization result of the draft tube shows a marked performance improvement over the original, which verifies the theoretical validity and feasibility of the proposed method in this paper.

The reconstruction of traffic accidents has grown as an interdisciplinary field since the first accident occurred. Various methods have been developed over time, starting with primary data collected at the scene of the accident. In this work, I proposed a method by which the value of the force in the safety belt buckle can be determined when it is equipped with a pretensioning system with pyrotechnic trigger in the tube, PBP or PLP type. The anti-return system of the pretensioner mechanism, which prevents the passenger's body from moving forward, contains a set of balls that block the movement of the piston in the pretensioner tube after its activation. When limiting the movement, the force the human body exerts on the safety belt webbing is transformed into the deformation of the pretensioner tube by the balls of the anti-return system. Depending on the magnitude of the force, the marks left by the balls differ. I propose a relationship of dependence between the acting force and the deformation of the tube. An experimental test bench was created to perform shock traction tests on the pre-tensioning system, under similar conditions to those of the human body acting on the belt in case of a frontal collision. Following the tests, the force value of the seat belt buckle cable and the diameter of the spherical indentations that the balls left in the pretensioner tube were measured. A mathematical model was proposed to determine the normal force with which a ball from the anti-return system deforms the tube. The normal force was also determined by two other methods specific to contact mechanics and used in the specialized literature. By comparing the normal forces obtained by the three methods, a good correlation between the proposed mathematical model and the Komvopoulos-Ye method resulted, the "Hardness" method not being suitable for this study. The determined polynomial regression curve allows finding out the force in the cable of the closer depending on the size of the deformations produced by the balls in the tube. The forces in the belt webbing can be thus determined and biomechanics specialists can evaluate the injuries to the chest and abdomen of the occupants of a vehicle.

This study aimed to investigate the efficacy of probiotics in elderly hospitalized tube-fed patients undergoing antibiotic therapy for Clostridium difficile-associated diarrhea (CDAD). Probiotics were administered to 29 patients, with twice-daily doses for 7 days following the completion of antibiotic treatment. In the probiotic group, while stool form showed no significant change, there was a significant decrease in stool frequency. Conversely, the control group exhibited improved stool form but not frequency. The probiotic group maintained a significant difference in stool form during the follow-up period. Additionally, the control group showed a positive correlation between stool form, frequency, antibiotic therapy, and intensive care unit admission, which was not observed in the probiotic group. These findings suggest that supplementing with probiotics can effectively normalize stool form in elderly hospitalized tube-fed patients undergoing antibiotic treatment for CDAD, highlighting the potential benefits of probiotic intervention in this specific population.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

We delve into the axion-dilaton model within the supergravity framework, with a specific focus on the intricacies of domain wall construction and stability. Employing holographic vitrification, we unravel the dynamics of domain wall formation in gauge theories featuring periodic vacuum structures. Our model, incorporating a QCD-like axion term and a stabilizing dilaton, undergoes scrutiny for conductivity variations under weak disorder. The investigation reveals the model's resilience, manifesting near-perfect conductivity under mild disorder conditions. However, the rigorous mathematical motivation for the holographic setup demands further elucidation. The scattered nature of our results prompts the necessity for a more systematic interpretation of QCD phenomena and conductivity transitions. This study contributes to the mathematical understanding of the axion-dilaton model's behavior, highlighting the imperative for a refined holographic framework and a more coherent interpretation of observed phenomena.

Morphogenesis remains a riddle, wrapped in a mystery, inside an enigma. It remains a formidable problem viewed from many different perspectives of morphology, genetics, and computational modelling. We propose a biochemical reductionist approach that shows how both internal and external physical forces contribute to plant morphogenesis via mechanical stress-strain transduction from the primary cell wall tethered to the plasma membrane by a specific arabinogalactan protein (AGP). The resulting stress vector with direction defined by Hechtian adhesion sites, has a magnitude of a few picoNewtons amplified by a hypothetical Hechtian growth oscillator. This paradigm shift involves stress activated plasma membrane Ca2+channels and auxin-activated H+-ATPase. The proton pump dissociates periplasmic AGP-glycomodules that bind Ca2+. Thus, as the immediate source of cytosolic Ca2+ an AGP-Ca2+ capacitor directs vectorial exocytosis of cell wall precursors and auxin efflux (PIN) proteins. In toto these components comprise the Hechtian Oscillator and also the gravisensor. Thus interdependent auxin and Ca2+ morphogen gradients account for the predominance of AGPs. The size and location of a cell surface AGP-Ca2+ capacitor is essential to differentiation and explains AGP correlation with all stages of morphogenetic patterning from embryogenesis to root and shoot. Finally, evolutionary origins of the Hechtian Oscillator in the unicellular Chlorophycean algae reflect the ubiquitous role of chemiosmotic proton pumps that preceded DNA at the dawn of life.

Crown gall (Agrobacterium tumefaciens), crown/root rot (Phytophthora spp.), root lesion disease (Pratylenchus vulnus), and tree vigor are key traits affecting productivity and quality of walnuts in California. Non-inoculated hybrid rootstocks were analyzed by RNA-seq to examine pre-formed factors affecting these traits. Enrichment analysis of the differentially expressed genes revealed that increased expression of cell wall biogenesis-related genes plays a key role in susceptibility to A. tumefaciens, Phytophthora spp., increased vigor, but not P. vulnus. Analysis of the predicted subcellular loci of the encoded proteins revealed that many gene products associated with vigor and susceptibility were targeted to the plasma membrane and extracellular space, connecting these traits to sustaining barrier function. We observed that RNA processing and splicing, along with predicted nuclear targeting, were associated with resistance to A. tumefaciens, Phytophthora spp., low vigor, but not P. vulnus. Four genes within the J. microcarpa QTL region for resistance to A. tumefaciens and Phytophthora spp. were represented among our transcripts, with two of the genes being differentially expressed in association with resistance to A. tumefaciens and decreased vigor. No differential expression related to Phytophthora spp. or P. vulnus traits was observed in this region. Additionally, the J. microcarpa haplotype expressed more transcripts associated with resistance to A. tumefaciens, Phytophthora spp., and low vigor, but not P. vulnus than the J. regia haplotype. We also report unique and shared hormone and defense responses associated with each trait. This research suggests a link between cell wall biogenesis, vigor, and critical root diseases of walnut.

Introduction: intraocular pressure (IOP) measurement is an essential part glaucoma’s diagnosis and follow-up. Goldmann applanation tonometry (GAT) is the gold standard for IOP measurement but it’s affected by many factors like central corneal thickness (CCT). Racial differences in CCT are reported but the Syrian population was never studied.Research design and methods: 57 subjects with 114 eyes visiting Damascus hospital were examined and 100 eyes were included. IOP was measured using GAT and CCT was measured using OCULUS Pentacam AXL Corneal Topography, demographic data and history of ocular surgery, systemic co-morbidities and history of medications were collected. IOP values were corrected for CCT.Results: 56% were males, the mean age was 48.1. 24% of subjects had hypertension. Males had higher CCT with 557.23± 25.33 compared with 531.34 ± 41.88 for females. There was a moderately positive correlation between CCT and IOP (r=0.232, p-0.02), CCT and IOP values were linearly correlated (ANOVA, p=0.02).Conclusions: This study showed that the correlation between CCT and IOP is present in the Syrian population. Males had a slightly thicker corneas than females and CCT didn’t significantly change with age.

Age-related macular degeneration (AMD) causes visual impairment in individuals >50 years of age. However, no study has investigated AMD using ultra-wide-field swept-source optical co-herence tomography (UWF SS-OCT). We aimed to evaluate central and peripheral choroidal thickness using UWF SS-OCT and compare AMD subtypes. We included 75 eyes of patients with typical AMD (tAMD), 56 with polypoidal choroidal vasculopathy (PCV), 29 with pachychoroid neovasculopathy (PNV), and 12 with retinal angiomatous proliferation (RAP). To compare cho-roidal thicknesses in the central and peripheral choroids, we established subfields of <3 mm, <9 mm, and 9–18 mm from the fovea. PNV patients were significantly younger than those with tAMD (P=0.01). The choroidal thicknesses of PNV were significantly greater than that of tAMD in all subfields (P<0.01) and choroidal thickness significantly correlated with age and axial length in all subfields (P<0.05). Even after adjusting for age and axial length, the choroidal thickness in PNV was significantly greater than that in tAMD (P<0.05). In addition, the ratio of the posterior < 9 mm to peripheral 9–18 mm choroidal thickness in PNV was significantly greater than that in tAMD (P<0.01). A thickened choroid in PNV was more pronounced in the posterior choroid than in the periphery.

Toshiba devised the bladeless fan (or Air Multiplier) concept in 1981. Researchers like James Dyson and Jafari et al. further developed it. Bladeless fans are more energy-efficient, safer due to the hidden blades, easier to clean, and more adjustable than conventional fans. From a performance point of view, bladeless fans are better because they multiply mass flow rate, eliminate buffeting, consume less power, and are quieter. This paper investigates the influence of the airfoil’s outlet slit thickness on the discharge ratio by varying the outlet slit thickness of an Eppler 473 airfoil from 1.2 mm to 2 mm in intervals of 0.2 mm. Results indicated that smaller slits showed higher discharge ratios. The airfoil with a 1.2 mm slit thickness showed a discharge ratio of 18.78, a 24% increase from the discharge ratio of the 2 mm slit. The effect of outlet angle on the pressure drop across the airfoil was also studied. Outlet angles were varied from 16∘ to 26∘ by an interval of 2∘. The airfoil profile with a 24∘ outlet angle showed a maximum pressure difference of 965 Pa between the slit and leading edge. In contrast, the 16∘ outlet angle showed the least pressure difference of 355 Pa. Parameters such as average velocity, turbulent kinetic energy, the standard deviation of velocity and outlet velocity magnitude was used to assess the performance of airfoil profiles used in bladeless fan.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Overhead power transmission line icing (PTLI) disasters are one of the most severe dangers to power grid safety. Automatic iced transmission line identification is critical in various fields. However, existing methods primarily focus on the linear characteristics of transmission lines, employing a two-step process involving edge and line detection for PTLI identification. Nonetheless, these traditional methods are often difficult when confronted with challenges such as background noise or variations in illumination, leading to incomplete identification of the target area, missed target regions, or misclassification of background pixels as foreground. We propose a new iced transmission line identification scheme to overcome this limitation. In the initial stage, we integrate the image restoration method with image filter enhancement to restore the image's color information. This combined approach effectively retains valuable information and preserves the original image quality, thereby mitigating noise presented during the image acquisition. Subsequently, in the second stage, we introduce an enhanced multi-threshold algorithm to separate background and target pixels. After image segmentation, we enhance the image and obtain the region of interest (ROI) through connected component labeling modification and mathematical morphology operations, eliminating background regions. Our proposed scheme achieves an accuracy value of 97.72%, a precision value of 96.24%, a recall value of 86.22%, and the specificity value of 99.48% based on the average value of test images. Through object segmentation and location, the proposed method can avoid background interference, effectively solve the problem of transmission line icing identification, and achieve 90% measurement accuracy compared to manual measurement on the collected PTLI dataset.

The purpose of the study was to determine the “retinal thickness deviation” (RTD) in diabetic macular edema (DME) eyes treated with intravitreal therapy and to establish associations be-tween RTD and best-corrected visual acuity (BCVA). We conducted a retrospective study, in-cluding consecutive DME eyes undergoing intravitreal therapy with two years of follow-up. BCVA and central subfield thickness (CST) were collected at baseline, 12 months and 24 months of follow-up. RTD was calculated as the absolute difference between measured and normative CST values at each time point. Linear regression analyses were performed between RTD and BCVA and between CST and BCVA. One hundred and four eyes were included in the analysis. The RTD was 177.0 (117.2) μm at baseline, 97.0 (99.7) μm at 12 months and 89.9 (75.3) μm at 24 months of follow-up (P < .001). RTD showed a moderate association with BCVA at baseline (R2=0.134, p<0.001) and 12 months (R2=0.197, p<0.001), and a substantial association at 24 months (R2=0.272, p<0.001). The CST showed a moderate association with BCVA at baseline (R2=0.132, p<0.001) and 12 months (R2=0.136, p<0.001), while the association was weak at 24 months (R2=0.065, p=0.009). In conclusion, RTD showed a good association with visual outcome in DME eyes undergoing intravitreal treatment.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

The co-circulation of duck hepatitis A virus subtypes 1 (DHAV-1) and 3 (DHAV-3) in ducklings has resulted in significant economic losses. Because ducklings infected with DHAV-1 or DHAV-3 show similar clinical signs and gross lesions, it is important to discriminate these subtypes as early as possible for better clinical management. On the basis of multiple alignments of the 5′-noncoding region sequences of strains DHAV-1 and DHAV-3, universal and type-specific primers were designed and synthesized. Using the primers in a one-tube reverse transcription-PCR (RT-PCR) assay, reference strains of DHAV-1 and DHAV-3 (isolated over a span of 60 years and covering many different countries) were successfully amplified, indicating that the primer sequences were completely conserved. The amplicon sequences results and the sizes of amplicons from reference DHAV-1 and DHAV-3 isolates correlated completely with their genotypes. Moreover, with this one-tube RT-PCR system, the amplicon sizes of liver samples of reference DHAV-1- or DHAV-3-infected birds matched perfectly with their respective genotypes, as determined by virus isolation and neutralization tests. No other RNA viruses of duck origin were detected with the synthesized primers. The sensitivity of viral RNA detection was 10 pg. With this system, 20% genotype 1, 45% genotype 3, and 9% co-infection of the two genotypes were detected in 55 clinical samples. This novel approach could be used for the rapid genotyping DHAV-1 and/or DHAV-3 infection in routine clinical surveillance or epidemiologic screening.

Hollow and concrete-filled steel tubes (CFSTs) are widely used as columns in many structural systems and local buckling can occur when they are subjected to axial compression loading. The critical regions for the local buckling of the columns are near the ends of the column where the moments are the highest. To strengthen the critical regions of the CFSTs the CFRP provides a simple and effective method which used previously as an enhancement for both of strength and ductility. So, this study suggests investigating the axial load behaviour of CFST strengthened with CFRP using FE method after a verification study and then a various parametric studies were carried out to cover the effect of the CFRP layers, number, confinement length and position. The FE results proved that, one CFRP sheet with thickness equal to 1.2 mm was strengthened the composite column by 8.5%, two CFRP sheets with total thickness equal to 2.4 mm was strengthened the composite column by 23.5%, three CFRP sheets with total thickness equal to 3.6 mm was strengthened the composite column by 35.1% and four CFRP sheets with total thickness equal to 4.8 mm was strengthened the composite column by 44.5%. Moreover, this study proved that by strengthened the composite columns with CFRP sheets with different lengths, the axial load resistance was improved by 8.5%, 4.6%, 0.1% and 0.0% for length percentages 100%, 75%, 50% and 25% respectively.

It is generally accepted that the human abdominal wall is comprised of skin, subcutaneous tissues, muscles and their aponeuroses, and the parietal peritoneum. Understanding these layers and their mechanical properties provides valuable information to those designing procedural skills trainers, supporting surgical procedures (hernia repair), and engineering-based work (in silico simulation). However, there is little literature available on the mechanical properties of the abdominal wall in layers or as a composite. This work characterizes the tensile properties of the human abdominal wall by layer and as a partial composite. Tissues were collected from fresh-never-frozen and fresh-frozen cadavers and tested in uniaxial tension at a rate of 5 mm/min until failure. Stress-strain curves were created for each sample, and the values for elastic moduli, ultimate tensile strength, and strain at failure were obtained. The experimental outcomes from this study demonstrated variation of tensile properties within and between tissues. The data also suggest that the tensile properties of composite abdominal walls are not additive. Ultimately, this body of work contributes to a deeper comprehension of these mechanical properties and will serve to enhance patient care, refine surgical interventions, and assist with more sophisticated engineering solutions.

The present study provides new insights into the growth of brown algal cell wall by showing that cell wall polysaccharide plays an important role in the process of growth consider- ing the physicochemical characteristic of young and old Cladosiphon okamuranus. To determine its structural variation in detail, the cell wall was sequentially fractionated into five fractions: hot water (HW), ammonium oxalate, hemicellulose-I (HC–I), HC-II, and cellulose, and analyzed physicochemically. Results showed that almost 80% of the total recovery cell wall from both young and old thalli was HW and HC-I contained mainly fucoidan composed of Fuc, GlcA, and sulfate in molar ratios of 1.0: 0.3: 0.6~0.7 and 1.0: 0.3: 0.2~0.3, respectively. Fucoidan in HW was a highly sulfated matrix polysaccharide abundance in young thalli, while fucoidan in HC-I was rich in old thalli and functions as hemicellulose in land plants, crosslink with cellulose and strengthen the cell wall. We found that HW and HC-I were particularly involved in the growth and strength of old thalli appeared to be due to the deposition of HC-I and reducing of water content during the growth process.

In this paper, we present and analyze a compact inner-wall grating slot microring resonator (IG-SMRR) with the footprint of less than 13 μm × 13 μm on the SOI platform for label-free sensing, which comprises a slot microring resonator (SMRR) and inner-wall grating (IG). Its detection range is significantly enhanced without the limitation of the free spectral region (FSR) owing to the combination of SMRR and IG. Structural parameters of IG and SMRR are investigated and optimized for favorable transmission properties. The simulation results shows that the IG-SMRR has an ultra-large quasi-FSR of 84.6 nm, and the concentration sensitivities of sodium chloride solutions and D-glucose solutions are up to 960.61 pm/% and 933.06 pm/%, respectively. The investigation on the combination of SMRR and IG is a valuable exploration of label-free sensing application for ultra-large detection range and ultra-high sensitivity in future.

We are in amidst of COVID-19 pandemic. Since Dec 2019, severe acute respiratory corona virus (SAR-CoV-2) has infected more than half a billion people killing nearly 7 million people worldwide. Now the BA.5 variant of SARS-CoV-2 is causing mayhem and driving the global surge. Epidemiologist are aware of the fact that this virus is capable of escaping immunity and likely to infect the same person multiple times despite adequate vaccination status. Elderly people of age more than 60 years and those with underlying health conditions are considered as high-risk who are likely to suffer complications and death. While it is tempting to frame complications and mortality from COVID-19 as a simple matter of too much of a virulent virus in too weak of a host, much more is at play here. Framing the pathophysiology of COVID-19 in the context of the Chrousos and Gold model of the central stress response system can shed insight into its complex pathogenesis. Understanding the mechanisms by which pharmacologic modulation of the central stress response system via administration of clonidine and/or dexamethasone may offer an explanation as to why a viral pathogen can be well tolerated and cleared by one host while inflaming and killing another.

The thoracic surgery has increased drastically in recent years, especially in the light of the severe outbreak of 2019 novel coronavirus disease (COVID-19). Routine “passive” chest computed tomography (CT) screening of inpatients detects some pulmonary diseases requiring thoracic surgeries timely. As an essential device for thoracic anesthesia, the double-lumen tube (DLT) is particularly important for anesthesia and surgery. With the continuous upgrading of the DLTs and the widespread use of the fiberoptic bronchoscopy (FOB), the position of DLT in thoracic surgery is gradually becoming more stable and easier to observe or adjust. However, the DLT malposition still occurs during transferring patients from supine to lateral position in thoracic surgery, which leads to lung isolation failure and hypoxemia during one-lung ventilation (OLV). Recently some innovative DLTs or improved intervention methods have shown good results in reducing the incidence of DLT malposition. This review aims to summarize the recent studies of the incidence of left-sided DLT malposition, the reasons and effects of malposition, and summarize current methods for reducing DLT malposition and prospects for possible approaches. Meanwhile, we use bibliometric analysis to summarize the research trends and hot spots of the DLT research.

A labyrinth metamaterial wall with glass coverage is measured in a reverberating chamber and after its installation in a restaurant. Glass is used to meet two aims, namely acoustic absorption and visual design demands. The wall consists of five multiple labyrinth elements of 1.83 m$^2$ each. Glass was taken to make the wall act as a room lightning device where a translucent cover material is needed. Absorption measurements show about four times improved absorption compared to typical glass. Due to the metamaterial behavior, absorption is high in the low-frequency range below 300 Hz where damping is problematic with traditional materials. Especially in this range, the glass metamaterial wall is an excellent compromise between room acoustic and visual design demands, as loud low-frequencies make visitors speak louder and experience less intimacy with additionally reduced speech intelligibility. For mid-frequencies, absorption is shown less effective and improvements are discussed.

Topological states of matter have attracted significant attention due to their intrinsic wave-guiding and localization capabilities robust against disorders and defects in electronic, photonic, and phononic systems. Despite the above topological features phononic crystals share with their electronic and photonic counterparts, finite-frequency topological states in phononic crystals may not always survive. In this work, we discuss the survivability of topological states in Su-Schrieffer-Heeger models with both local and non-local interactions with larger symmetry perturbation. Although such a discussion is still about ideal mass-spring models, the insights from this study set the expectations in continuum phononic crystals, which can further instruct the applications of phononic crystals for practical purposes.

1). BACKGROUND: Cell wall deficient mycobacteria (CWDM) have seldom been isolated in bacterial culture from human subjects. particularly in clinical disease, such as Crohn’s disease. Techniques have focused on the use of polymerase chain reaction (PCR) for the detection of CWDM in association with inflammatory bowel disease. (IBD). This paper is a report of the development of methods to demonstrate the presence of CWDM using the Ziehl-Neelsen (ZN) stain. This is in addition to the detection of the growth of CWDM in fluid media. 2). METHODS: The use of the ZN stain is suitable for the demonstration of CWDM in clinical samples and cultures, when the staining methods that were common prior to the 1970’s, are adopted. Specific culture media are developed and tested in parallel. Alterations in the concentration of basic fuchsin, and changes in the decolourising solutions are necessary. Decolourising solutions such as 20% concentrated sulphuric acid in water are preferable for detection of CWDM in cultures. 3). RESULTS: CWDM can be readily demonstrated using the simple methods outlined in this report. The ability to visualise the presence of CWDM opens the door to the development of specific fluid media for the isolation of CWDM in culture. 4). CONCLUSION: The ZN stain methods optimised for the demonstration of Mycobacterium tuberculosis complex (MTBC) are not suitable for research into infectious causes of inflammatory bowel disease (IBD), as well as for the detection of CWDM in latent tuberculosis. Revisiting the techniques for the detection of CWDM may also refocus attention on inflammatory diseases considered to be idiopathic, but having hallmarks of an infectious process.

This research elucidates the dynamic expression of expansin genes during the wheat grain (Triticum aestivum L.) development process using comprehensive meta-analysis and experimental validation. We leveraged RNA-seq data from multiple public databases, applying stringent criteria for selection, and identified 60,852 differentially expressed genes across developmental stages. From this pool, 28,558 DEGs were found to exhibit significant temporal regulation in at least two different datasets, and were enriched for processes integral to grain development such as carbohydrate metabolism and cell wall organization. Notably, 30% of the 241 known expansin genes showed differential expression during grain growth. Hierarchical clustering and expression level analysis revealed temporal regulation and distinct contributions of expansin subfamilies during the early stages of grain development. Further analysis using co-expression networks underscored the significance of expansin genes, revealing their substantial co-expression with genes involved in cell wall modification. Finally, qPCR validation and grain morphological analysis under field conditions indicated a significant negative correlation between expression of select expansin genes and grain size and weight. This study illuminates the potential role of expansin genes in wheat grain development and provides new avenues for targeted genetic improvements in wheat.

With the objective of studying the influence of elicitors on growth, yield and quality of kalmegh we carried out an investigation for two consecutive years. Nine treatments with three replications were laid out in CRD design. Chitosan, Yeast extract, Jasmonic acid and Salicylic acid were evaluated at different concentrations. CHT 1000 ppm exhibited highest plant height (73.91 cm) and secondary branches (29.07) at the time of harvest. Primary branches and number of leaves per plant were highest in CHT 1000 ppm (26.36; 88.32) which were on par with SA 200 ppm (26.28; 81.51). Plant spread was highest in SA 200 ppm (35.46 cm2) which was on par with CHT 1000 ppm (35.11 cm2). CHT and SA sprays were recorded with on par results for yield parameters but highest fresh (42.34 g) and dry (18.30) herbage yield per plant were exhibited with SA 200 ppm. Highest total chlorophyll (4.459 mg g-1) and total andrographolides (3.494%) content were recorded in SA 200 ppm spray. Significant and positive improvement in growth, yield and quality of kalmegh was noticed with Salicylic acid spray @ 200 ppm at 30 and 60 DAS signifying its use in cultivation of kalmegh for high productivity, quality and better returns for farmers.

Aflatoxins, which have been classified as a group-1 carcinogen are the well-known mycotoxins produced by Aspergillus flavus. Aflatoxins have been linked to liver diseases, acute hepatic necrosis, resulting in cirrhosis or hepatocellular carcinomas due to which it incurs a loss of value in international trade for peanuts contaminated with it. The four main aflatoxins are B1, B2, G1, and G2 of which B1 is predominant. In plants, the cell wall is the primary barrier against pathogen invasion. Cell wall fortifications such as deposition of callose, cellulose, lignin, phenolic compounds and structural proteins help to prevent the pathogen infection. Further, the host cell’s ability to rapidly repair and reinforce its cell walls will result in a reduction of the penetration efficiency of the pathogen. Peanut seed coat acts as a physical and biochemical cell wall barrier against both pre and post-harvest pathogen infection. The structure of seed coat and the presence of polyphenol compounds have been reported to inhibit the growth of A. flavus, however, not successfully employed to develop A. flavus resistance in peanut. A comprehensive understanding of peanut seed coat development and biochemistry will provide information to design efficient strategies for the seed coat mediated A. flavus resistance and Aflatoxin contamination.

Lake ice thickness (LIT) is a sensitive indicator of climate change identified as a thematic variable of Lakes as an Essential Climate Variable (ECV) by the Global Climate Observing System (GCOS). Here, we present a novel and efficient analytically based retracking approach for estimating LIT from high-resolution Ku-band (13.6 GHz) synthetic aperture radar (SAR) altimetry data. The retracker method is based on the analytical modeling of the SAR radar echoes over ice-covered lakes that show a characteristic double-peak feature attributed to the reflection of the Ku-band radar waves at the snow-ice and ice-water interfaces. The method is applied to Sentinel-6 Unfocused SAR (UFSAR) and Fully Focused SAR (FFSAR) data, with their corresponding tailored waveform model, referred to as the SAR_LITand FFSAR_LITretracker, respectively. LIT retrievals from Sentinel-6 SAR data at different posting rates are evaluated against those obtained from thermodynamic lake ice model simulations and Low Resolution Mode (LRM) Sentinel-6 and Jason-3 data over two ice seasons during the tandem phase of the two satellites, allowing precise assessment of the continuity between LRM and SAR LIT retrievals. Consistency checks of the Sentinel-6 SAR LIT estimates are also performed using optical/radar images that provide information on the snow/ice conditions on the same dates. The analysis is performed on Great Slave Lake and Baker Lake (Canada) that differ in terms of lake size, bathymetry, snow/ice properties, and seasonal evolution of LIT. The accuracy of the LIT estimates with the SAR LIT retrackers is on the order of 5 cm once the ice is well established on the lakes, meeting the GCOS requirements of LIT measurement uncertainty, which is a factor of 2 to 3 times better than that of LIT obtained with LRM data, bringing a further improvement compared to previous analyses and methods. The SAR LIT retrackers presented are promising tools for monitoring the inter-annual variability and trends in LIT from current and future SAR altimetry missions.

Pachychoroid neovasculopathy (PNV) is a pachychoroid-spectrum disease. As blood circulation throughout the choroid may be involved in PNV pathogenesis, analysis using ultra-wide-field (UWF) fundus imaging is crucial. We evaluated choroidal thickness after half-fluence photodynamic therapy (PDT) combined with intravitreal aflibercept injection for PNV using UWF swept-source optical coherence tomography. Seventeen eyes with PNV that underwent half-fluence PDT with adjuvant single intravitreal aflibercept injection were analyzed. To compare choroidal thicknesses in the central and peripheral choroids, we set subfields <3, <9, and 9–18 mm from the fovea. The <9- and 9–18-mm subfields were divided into four quadrants. Choroidal thickness in each subfield decreased significantly after half-fluence PDT (P<0.001); this reduction was more pronounced in the central area. We also investigated the relationship between the dominant side of the deep choroidal veins that harbor choroidal vein efflux from the macula. When choroidal thickness in the supratemporal and infratemporal 9x9-mm subfields were evaluated, the ratio of choroidal thickness reduction was not significantly different between the dominant and non-dominant sides. The dominant side was not associated with the extent of choroidal thickness reduction in PNV. In conclusion, half-fluence PDT caused thinning of the entire choroid, especially in the central area, in PNV.

Systematic results of lattice dynamical calculation are reported for the novel (SiC)m/(GeC)n superlattices (SLs) by exploiting a modified-linear chain model (M-LCM) and a realistic rigid-ion- model (RIM). By employing the bond polarizability method in the framework of M-LCM, we have simulated Raman intensities for the graded (SiC)10-D/(Si0.5Ge0.5C)D/(GeC)10-D/(Si0.5Ge0.5C)D SLs by carefully integrating interfacial layer thickness D (≡ 0, 1, 2, 3 monolayers (MLs)). The variation of D has initiated considerable up (down) shifts of GeC-, (SiC)-like Raman peaks in the middle of the optical phonon frequency region. With D = 3 MLs, the maximum energy shift (by ~ 47 cm-1) of SiC-like modes has caused substantial changes in the Raman intensity profiles linked to the localization of atomic displacements at the interfacial transition regions. This effect can be considered as a vital tool for authenticating the interfacial structures in technologically important SLs. By using a RIM, we have reported SL phonon dispersions along the growth [001] as well as in the plane [100], [110] perpendicular to the growth. Our simulations of phonons in the acoustic mode region have not only confirmed the formation of minigaps at the zone center and zone edges but also provided evidence of anti-crossing and phonon confinement. Besides examining angular dependence of zone-center optical modes, we have also discussed phonon folding, confinement and anisotropic behavior in (SiC)m/(GeC)n SLs.

The Combined Inversion of Surface and AeRosols (CISAR) algorithm for the joint retrieval of surface and aerosol single scattering properties has been further developed in order to extend the retrieval to clouds and overcome the need for an external cloud mask. Pixels located in the transition zone between pure cloud and pure aerosol are often discarded by both aerosol and cloud algorithms, despite being essential for studying aerosol-cloud interactions, which still represent the largest source of uncertainty in climate predictions. The proposed approach aims at filling this gap and deepening the understanding of aerosol properties in cloudy environments. The new CISAR version is applied to Sentinel-3A/SLSTR observations and evaluated against different satellite products and ground measurements. The spatial coverage is greatly improved with respect to algorithms processing only pixels flagged as clear sky by the SLSTR cloud mask. The continuous retrieval of aerosol properties without any safety zone around clouds opens new possibilities for studying aerosol properties in cloudy environments.

Plants characterized by a soft or weak steam, such as climbing plants, need to find a potential support (e.g., wooden trunk) to reach greater light exposure. Since Darwin’s research on climbing plants, several studies on their searching and attachment behaviors have demonstrated their unique ability to process different support features to modulate their movements accordingly. Nevertheless, the strategies underlying this ability are yet to be uncovered. The present research tries to fill this gap by investigating how the interaction between above- (i.e., stem, tendril, …) and belowground (i.e., the root system) plant organs influence the kinematics of the approach-to-grasp movement. With three-dimensional (3D) kinematical analysis, we characterized the movement of pea plants (Pisum sativum L.) towards a support with different thicknesses above and belowground (i.e., thin below, thick aboveground, or the opposite). As a control condition, the plants were presented to supports with the same thickness below- and aboveground (i.e., either entirely thin or thick). The results suggest an integration between the information from below- and aboveground for driving the reach-to-grasp behavior of the aerial plant organs. Information about the support conveyed by the root system seems particularly important to fulfil the end-goal of the movement.

Background Patients with severe dysphagia are usually fed using a nasogastric tube (NGT). Many patients who receive long-term NGT feeding are unable to obtain sufficient nutrients orally immediately after NGT removal. Thus, a transitional period involving oral diet training is required to transition from NGT feeding to exclusive oral feeding. We aimed to investigate the therapeutic effect of oral diet training in indwelling NGT patients with prolonged dysphagia. Methods A total of 175 patients who were fed using an NGT for more than 4 weeks were enrolled. Their swallowing function was evaluated by a videofluoroscopic swallowing study (VFSS). During the VFSS, patients received thick and thin barium while the NGT was insulted. Then, the patients underwent a VFSS without an NGT thirty minutes after NGT removal. If a patient had no aspiration with NGT inserted during the VFSS, oral diet training combined with NGT feeding was recommended. Results Of the 49 indwelling NGT patients who were recommended to receive oral diet training, 39 (79.6%) transitioned to exclusive oral feeding. A transition period of 2-8 weeks was required for them to achieve full oral feeding. Patients who were eligible for oral feeding trials showed no significant aspiration during the VFSS with an NGT inserted and had sufficient cough function. Patients who required prolonged NGT feeding and who could not complete oral trials showed significant aspiration during the VFSS when an NGT was inserted. Conclusion This study demonstrated that oral diet training combined with NGT feeding was safe in patients with prolonged dysphagia who had sufficient cough function and no aspiration during VFSS. We suggest that if the patient is a proper candidate for NGT removal, direct oral feeding training with an NGT inserted could be a useful therapeutic strategy during the transitional period from long-term NGT feeding to successful oral feeding.

Primary spontaneous pneumothorax (PSP) is a pleural disease that abruptly affects healthy adolescents and young adults, representing a common thoracic disorder in this age group. This study aimed to investigate the necessity of preoperative chest tube insertion in patients with PSP and to re-evaluate current clinical treatment approaches. A retrospective review of medical records was conducted for children and young adults aged 14–30 years, diagnosed with PSP and who underwent Video-assisted thoracoscopic surgery (VATS) between January 2016 and December 2022 at Wonju Severance Christian Hospital. Patients were retrospectively divided into two groups based on their initial treatment: chest tube insertion and non-chest tube insertion. Clinical data including demographics, treatment details, and outcomes were collected and compared. Total 128 cases of PSP were included in the study. The total length of hospital stay was significantly shorter in the non-chest tube group (p=0.000), which was attributed to the omission of pre-operative chest tube insertions. No significant differences were observed between the two groups in terms of postoperative complications or recurrence rates. In cases of young patients with PSP, omitting pre-operative chest tube insertion may be a viable option if the patient is scheduled for VATS.

In a power plant that uses seawater as a coolant, a debris filter is required to remove foreign substances from the seawater, and differential pressure leads to a decrease in the coolant flow rate, leading to a decrease in power generation efficiency. In this study, analysis was performed under different initial flow velocity conditions of 1.5m/s, 2.0m/s, and 2.5m/s for a debris filter used in a power plant to understand flow characteristics in CTCS. The flow and differential pressure characteristics of a CTCS with an installed debris filter were considered in a comparative analysis of velocity, pressure, and turbulent kinetic energy distribution. The results confirmed that a vortex was generated in the pipe with the debris filter, apparently due to the collision of the flow with the bracket of the debris filter. As the flow rate increased, the range of the vortex increased, causing a loss in flow.

The pulsating flow is one of the techniques which can enhance heat transfer, therefore leading to energy saving in tubular heat exchangers. This paper investigates the heat transfer and flow characteristics in a two-dimensional in-line tube bundle with the pulsating flow by a numerical method using the Ansys Fluent. Numerical simulation is performed for Reynolds number Re = 500 with different frequencies and amplitude of pulsation. Heat transfer enhancement was estimated from the central tube of the tube bundle. Pulsation velocity had an asymmetrical character with a reciprocating flow. The technique developed by the authors to obtain asymmetric pulsations was used. This technique allows simulating an asymmetric flow in heat exchangers equipped with a pulsation generation system. Increase in both the amplitude and the frequency of the pulsations has a significant effect on heat transfer enhancement. Heat transfer enhancement is mainly observed in the front and back of the cylinder. At a steady flow in these areas, heat transfer is minimal due to the weak circulation of the flow. The increase in heat transfer in the front and back of the cylinder is associated with increased velocity and additional flow mixing in these areas.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

Nanomagnetism and spintronics are currently active areas of research, with one of the main goals being the creation of low-energy-consuming magnetic memories based on nanomagnet switching. These types of devices could also be implemented in neuromorphic computing by crafting artificial neurons (ANs) that emulate the characteristics of biological neurons, through the implementation of neuron models such as the widely used leaky integrate-and-fire (LIF) with a refractory period. In this study, we have carried out numerical simulations of a 120 nm diameter, 250 nm length ferromagnetic nanowire (NW) with the aim of exploring the design of an artificial neuron based on the creation and destruction of a Bloch-point domain wall. To replicate signal integration, we applied pulsed trains of spin-currents to the opposite faces of the ferromagnetic NW. These pulsed currents (previously studied only in the continuous form) are responsible for inducing transitions between the stable single vortex (SV) state to the metastable Bloch point domain wall (BP-DW) state. To ensure the system exhibits the leak and refractory properties, the NW was placed in an homogeneous magnetic field of the order of mT in the axial direction. The suggested configuration fulfills the requirements and characteristics of a biological neuron, potentially leading to the future creation of Artificial Neural Networks (ANNs) based on reversible changes in the topology of magnetic NWs.

Gut microbiota affects progression of rheumatoid arthritis (RA). The present study aims at investigating the protective potential of Bifidobacterium longum cell wall lipoproteins (Lpps) shown to modulate the intestinal microbiome and prevent osteoarthritis. Arthritis was induced by collagen (CIA) or anti-collagen antibodies (CAIA) injection. Intake of 0.5 mg Lpps /L, but not 0.25 and 1mg Lpps/L significantly alleviated RA symptoms in CIA DBA/1OOaHsd mice. Arthritis index (AI) was also reduced in CAIA mice. In CIA protected group, colon Ligilactobacillus murinus, caecal Lactobacillus johnsonii and spleen weight correlated with AI, whereas the reverse was observed with splenic CD11c+ dendritic cells (cDCs). The unprotected CIA Lpps group harbored higher caecal and colon E. coli and lower caecal L.murinus. Lpps administration to CAIA mice after arthritis induction led to lower colon E. plexicaudatum counts. Splenocytes from CIA protected mice triggered by LPS secreted higher Il-10 than control ones. However, higher IL-10 response was not elicited in gnotobiotic RA mice splenocytes with lower cDCs recruitment. Labeled bacteria with Lpps signal were detected in CIA mice bone marrow (BM) cDCs 5 and 16h post-gavage but not in Peyer’s patches and spleen. In vitro uptake of Lpps by primary BM and thymus cells was observed within 24h. FACS analysis detected the Lpps signal in the plasmacytoid cell compartment but not in cDCs. In conclusion, Lpps dosing is critical for preventing arthritis progression and appropriately modulating the microbiome. Our results also highlight the possible triggering of the immune system by Lpps.

Quasistatic nanoindentation is a proven tool that provides information on the micromechanical behavior of wood cell walls. However, quasistatic tests cannot probe the time-dependent mechanical behavior shown by wood. Nanoindentation dynamic mechanical analysis (nanoDMA) can mesaure the viscoelastic properties of wood cell walls. This research aimed to study the quasistatic and viscoelastic properties of individual radiata pine wood (Pinus radiata D. Don) cell wall layers. To minimize variability and retrieve both properties at the same locations, a load function composed of a multiload-quasistatic function followed by dynamic reference frequency segments was developed. Nanoindentations were then performed on the S2 layer and compound corner middle lamella (CCML) of unembedded latewood cells. Because the S2 layer is anisotropic, both transverse and longitudinal-tangential wood planes were studied. In the transverse plane, the average results of the quasistatic elastic moduli (Es) for the S2 layer and CCML were 15.7 GPa and 4.6 GPa, respectively. In the longitudinal-tangential plane, the E_s was 3.9 GPa. In the transverse section, the hardness (H) of the S2 layer and CCML were 331 MPa and 277 MPa, respectively, and in the longitudinal-tangential section H was 244 MPa. To acquire the viscoelastic properties, measurements were made over more than three decades of frequency. An increase of the storage modulus (E'), and a reduction of the loss modulus (E'') and loss factor (tan⁡ δ ) as frequency increased were found in both wood orientations. The quasi-static and dynamic indentations equivalent at 0.1 Hz showed similar values for Es and E’. This study contributes to our knowledge of wood cell wall micromechanical properties.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Domain walls were studied for permalloy wires with different depth trenches (500 nm wide, 30 nm thick, 7.5 µm long, the depth of the trench was 0, 4, 5, 8, 10, 12 and 15nm). Permalloy (Ni80Fe20) wires were fabricated by electron beam lithography and Ar ion milling. When the depth of trench is smaller than 12 nm, the switching field (Hs) is increasing with the deeper trench. However, the depth of trench is bigger than half depth of thickness, the Hs is decreasing with the deeper trench. We believed that Hs increased as the trench depth increased was because the magnetic diploes force increased between the magnetic poles on two sides of the trench. The domains of the wires were divided by the trenches and the domain walls were pinned on the trenches these were confirmed by magnetic force microscopy images.

The hot rolling in the process chain of the aluminium rolled products present the critical element of material quality and influence on productivity. The desire to increase the letter demand modifications of hot rolling, consequential changes of microstructure, crystallographic texture, mechanical and formability properties must be knowledge and consistently considered in planning the rolling process and rolled product. Achieving lower thicknesses of the hot-rolled band would enable fewer passes with cold rolling; consequently, hot rolling with the same number of passes will complete with lower temperatures. Microstructural and texture characterization with the optical microscope and scanning electron microscope for the hot-rolled band 3.25 mm the smaller grains appeared in the center of the cross-section, unlike for the hot-rolled band 6 mm, the smaller grains were detected on the upper and bottom position of the cross-section. Furthermore, the comparison shows also that the hot-rolled band 6 mm has 64 % of random texture components and 83 % of recrystallized grains, and the proportional adjustment for the hot-rolled band 3.25 mm has the 42 % of random texture components and 55 % of recrystallized grains. For the mechanical testing results, the elongation values in rolling and transverse directions significantly differ just in the case of a hot rolled band of 3.25 mm. Consequently, the earing results are more than 1.5 % higher for the hot-rolled band, 3.25 mm, than the hot-rolled band, 6 mm.

Eustachian Tube Dysfunction is considered a common condition among ENT patients and requires careful history, clinical examination and appropriate investigations to obtain a diagnosis. The ETDQ-7 questionnaire is a useful tool to subjectively score severity of symptoms that are related to this pathology (Appendix A). This study aimed to adapt and validate the ETDQ-7 questionnaire in Greece to ensure correct and efficient use in the outpatient setting (Appendix B). The ETDQ-7 was translated into the Greek language following appropriate methodology. Data for the main study were collected from a sample of 75 Greek patients diagnosed with ETD as well as 25 patients that did not have ETD and who served as a control group. The participants completed the adapted ETDQ-7 questionnaire and underwent a clinical examination that was statistically correlated with their ETDQ-7 answers. Face and content validity were confirmed and the questionnaire was found easy to administer and to be completed by our patients. Test-retest reliability revealed similar internal consistency for the questions and good correlation between individual items and total score. Discriminative validity confirmed statistically significant difference between the two patient groups to ensure that the Greek version of ETDQ-7 is useful to confirm the diagnosis. The Greek version of the ETDQ-7 is safe and efficient to use among a variety of investigation methods for the diagnosis of ETD in the Greek speaking population.