Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Cervical cancer is the most common female reproductive tract tumor and is currently the only cancer that can be prevented by vaccination. Early detection and treatment of cervical cancer can be achieved through regular screening for human papillomavirus (HPV). Therefore, in this paper, an electrochemical sensor was designed to detect HPV 16 using a dual signal amplification technique. APTES modified glassy carbon electrode to improve stability. Combining gold nanoparticles and chain amplification reactions for signal amplification purposes. The limit of detection (LOD) was 1.731×10-16 mol/L, and the detection range of this electrochemical sensor was increased in comparison to previous research, with a linear response range from 1.0×10-13 mol/L to 1.0×10-5 mol/L (R2 = 0.99232) for the target detector.In addition, the sensor showed equally good recovery in sophisticated human serum samples. It shows that it has good interference resistance and the designed biosensor can be a powerful and reliable tool for clinical disease diagnosis.

In this article, we describe an immunochromatographic test system developed for rapid serodiagnostics of cattle brucellosis using two markers: gold nanoparticles (GNPs) and quantum dots (QDs). The test system was compared with immunochromatographic serodiagnostics systems that use only one marker. The approbation of the test system was conducted on samples of cattle sera with low, but diagnostically significant titers of specific antibodies. We show that when two conjugates are used, the intensity of the detectable signal increases by 2–3 times compared with the test system using the QD conjugate and by more than 9 times compared with the system using the GNP conjugate.

Curcumin, found in the rhizome of turmeric, has extensive therapeutic promises via its antioxidant, anti-inflammatory, and antiproliferative properties. Preclinical in vitro and in vivo data have shown curcumin to be an effective treatment for multiple cancers. These effects are drived by curcumin's ability to induce G2/M cell cycle arrest, induction of autophagy, activation of apoptotic pathways, disruption of molecular signaling, inhibition of invasion and metastasis, and by increasing the efficacy of existing chemotherapeutics. Here we focused on the hormetic behaviour of curcumin. Frequently, low doses of toxins and other stressors not only are harmless but also activate an adaptive stress whereas high dose activates acute responses like autophagy and cell death. This phenomenon is referred to as hormesis. Many molecules that cause cell death elicite an initial autophagic step that is a cytoprotective mechanism relying on elimination of dysfunctional structures intracellular, notably by mitophagy. This phenomenon is considered as a primarily protective mechanism against stressors. At higher doses, cells undergo mitochondrial outer membrane permeabilization due to calcium release from the endoplasmic reticulum and die. Herein, we address the complex crosstalk between the induced mitochondrial biogenesis, mitochondrial destabilization accompanied by mitophagy and cell death that can also be at play.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Time evolution of the quantum correlation of the hybrid qubit-qutrit system in multilocal and global dephasing under the effect of a classical noises environment is presented. We considered the qutrit in z direction and the qubit x direction. In addition, our system presents two configurations: the different and the common environment and our discussion involves three types of noises: A Static Noise (SN), Random Telegraph Noise (RTN) and Ornstein- Uhlenbeck noise (OU). By using the density matrix approach to determine the evolution of the state of the system, the found that the static noise is fatal for the quantum entanglement, the quantum correlation and for RTN and OU noises the quantum entanglement, the quantum correlation decreases monotonically with a sufficiently long time. Therefore, we can say that, entanglement and the quantum correlation are more robust to the noise precisely those Random telegraph noise and Ornstein-Uhlenbeck noise.

The scattering pattern from a narrow absorbing/amplifying grating is investigated. A simple model of a narrow amplifying grating is solved exactly numerically and approximately analytically for the regime where the beam’s wavelength is much shorter than the grating’s wavelength. The main results are: The incident angle divides the scattering pattern into two regimes: below and above the incident angles. The former regime has a weak dependence on the incident angle but has a strong dependence on the scattering one. In this regime, a new grating formula is derived. The opposite occurs in the latter regime, which is very sensitive to the incident angle, but has only weak dependence on the scattering angle. Consequently, at certain incident angles, all the scattering is concentrated in the first regime, i.e., all scattering angles are lower than the incident angle.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

We investigate the use of amplitude amplification on the gate-based model of quantum computing as a means for solving combinatorial optimization problems. This study focuses primarily on QUBO (quadratic unconstrained binary optimization) problems, which are well-suited for qubit superposition states. Specifically, we demonstrate circuit designs which encode QUBOs as ‘cost oracle’ operations UC, which when combined with the standard Grover diffusion operator Us lead to high probabilities of measurement for states corresponding to the optimal and near optimal solutions. In order to achieve these probabilities, a single scalar parameter ps is required, which we show can be found through a variational quantum-classical hybrid approach.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Intelligent fault diagnosis techniques have replaced the time-consuming and unreliable human analysis, increasing the efficiency of fault diagnosis. Deep learning model can improve the accuracy of intelligent fault diagnosis with the help of its multilayer nonlinear mapping ability. This paper has proposed a novel method named Deep Convolutional Neural Networks with Wide First-layer Kernels (WDCNN). The proposed method uses raw vibration signals as input (data augmentation is used to generate more inputs), and uses the wide kernels in first convolutional layer for extracting feature and suppressing high frequency noise. Small convolutional kernels in the preceding layers are used for multilayer nonlinear mapping. AdaBN is implemented to improve the domain adaptation ability of the model. The proposed model addresses the problem that currently, the accuracy of CNN applied to fault diagnosis is not very high. WDCNN can not only achieve 100% classification accuracy on normal signals, but also outperform state of the art DNN model which is based on frequency features under different working load and noisy environment.

Versatility, sensitivity and accuracy have made the real-time polymerase chain reaction (qPCR) a crucial tool for research as well as diagnostic applications. However, for point-of-care (PoC) use traditional qPCR faces two main challenges: long run times mean results are not available for half an hour or more and the requisite high-temperature denaturation requires more robust and pow-er-demanding instrumentation. This study addresses both issues and revised primer and probe designs, modified buffers and low ∆T protocols which, together, speed up qPCR on conventional qPCR instruments and will allow the development of robust, point-of-care devices. Our approach, called "FlashPCR", also allows efficient reverse transcription as part of a one-step RT-qPCR pro-tocol, making it universally applicable for both rapid research and diagnostic applications.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

A general method is presented that permits enantiomers, originally present in a low enantiomeric excess (%ee1), to accumulate in a high %ee (%ee2) without a chiral source present. An equation was derived that demonstrates the final %ee2 of any unreacted chiral starting material will become higher when that starting material has reacted to generate an additional chiral center, hence forming two sets of diastereomeric enantiomeric products. Importantly, chiral amplification factor (multiples), %ee2/%ee1, depends on the yield of this reaction (p), which exhibits a nonlinear increase in amplification as p approaches 100%. This process is inevitable. It represents a possible route by which small initial %ee1 values of prebiotic molecules could have been raised to high %ee2 contents during the pre-evolution of life period on Earth, without the need for an added chiral source to be present. This predicted behavior was then experimentally verified in Pictet-Spengler reactions of L-tryptophane methyl ester (L-TME) samples present in low enantiomeric excess (%ee1) with biacetyl or oxaldehyde (model reactions) run to various yields. Each reaction generates stereoisomer products, and chiral amplification of the L-TME’s initial %ee1 values to higher %ee2 values occurs in the unreacted (recovered) L-TME. Repeated cycles of these reactions create very high L-TME %ee values. Self-cyclodimerization of low %ee1 L-amino acids with their D-enantiomers to generate L,L-, D,D- and L,D-cyclic products were computationally studied, leading to the same conclusion. Small %ee1 values are enhanced to larger %ee2 in the unreacted starting materials.

Numerous protocols have been published for extracting DNA from phlebotomines. Nevertheless, their small size is generally an issue in terms of yield, efficiency, and purity, for large-scale individual sand fly DNA extractions when using traditional methods. Even though this can be circumvented with commercial kits, these are generally cost-prohibitive for developing countries. We encountered these limitations when analysing parasite infection in Lutzomyia spp. by PCR [1] and, for this reason, we evaluated various modifications on a previously published protocol ([2] and Acardi personal communication). The most significant variation was the use of a different lysis buffer [3] to which added Ca2+ (buffer TESCa), because this ion protects proteinase K against autolysis, increases its thermal stability, and could have a regulatory function for its substrate-binding site [4]. Individual sand fly DNA extraction success was confirmed by amplification reactions using internal control primers that amplify a fragment of the cacophony gene [5,6]. To the best of our knowledge, this is the first time a lysis buffer containing Ca2+ has been reported for the extraction of DNA from sand flies.

The RV144 trial represents the only vaccine trial to demonstrate any protective effect against HIV-1 infection. While the reason(s) for this protection are still being evaluated, it serves as justification for widespread efforts aimed at developing new, more effective HIV-1 vaccines. Advances in our knowledge of HIV-1 immunogens and host antibody responses to these immunogens are crucial to informing vaccine design. While the envelope (Env) protein is the only viral protein present on the surface of virions, it exists in a complex trimeric conformation and is decorated with an array of variable N-linked glycans, making it an important but difficult target for vaccine design. Thus far, efforts to elicit a protective humoral immune response using structural mimics of native Env trimers have been unsuccessful. Notably, the aforementioned N-linked glycans serve as a component of many of the epitopes crucial for the induction of potentially protective broadly neutralizing antibodies (bnAbs). Thus, a greater understanding of Env structural determinants, most critically Env glycosylation, will no doubt be of importance in generating effective immunogens. Recent studies have identified the HIV-1 Env signal peptide (SP) as an important contributor to Env glycosylation. Further investigation into the mechanisms by which the SP directs glycosylation will be important, both in the context of understanding HIV-1 biology and in order to inform HIV-1 vaccine design.

Digital filtering is a fundamental technique in digital signal processing, which operates on a digital sequence without any information on how the sequence was generated. This paper proposes a methodology for designing the equivalent of digital filtering for neuromorphic samples, which are a low power alternative to conventional digital samples. In the literature, filtering using neuromorphic samples is done by filtering the reconstructed analog signal, which is required to belong to a predefined input space. We show that this requirement is not necessary, and introduce a new method for computing the neuromorphic samples of the filter output directly from the input samples, backed by theoretical guarantees. We show numerically we can achieve a similar accuracy compared to the conventional method. However, given that we bypass the analog signal reconstruction step, our results show significantly reduced computation time for the proposed method and good performance even when signal recovery is not possible.

Convolutional Neural Networks (CNNs) are often criticized for their lack of transparency, acting as 'black boxes' in decision-making, a challenge compounded by class imbalance in ECG datasets, which limits their clinical application. This study introduces a CNN-based ECG signal classification model that enhances interpretability and addresses class imbalance through the Synthetic Minority Over-sampling Technique (SMOTE). The model also integrates Uniform Manifold Approximation and Projection (UMAP) for dimensionality reduction and SHAP value analysis, facilitating the visualization of decision boundaries and the assessment of feature contributions. Our evaluation using the MIT-BIH Arrhythmia Database highlights the model's high performance, with accuracy and precision nearing 1.00 for Normal ECG (NOR), Left Bundle Branch Block (LBBB), Right Bundle Branch Block (RBBB), and Ventricular Premature Beat (PVC) in the six-class task. In the ten-class task, the model demonstrated robustness, particularly with an accuracy of 0.9846, precision of 0.9783, recall of 0.9736, and F1 score of 0.9760 in Pacemaker Fusion Beat (PFHB), supported by an AUC of 0.9999 and AP of 0.9885. These results underscore the model's efficacy in cardiac rhythm recognition and resilience to class imbalance. Future research will explore sophisticated model architectures and feature extraction methods to enhance the model's generalization and clinical applicability for early heart disease diagnosis and personalized treatment.

Bacterial phylogenetics has largely been determined via 16S rRNA gene sequencing and phylogenetic tree reconstruction. Observed utility of this approach has driven the popularity of the 16S rRNA gene amplicon metagenomics method for profiling and identifying diverse microbes from specific habitats. This work sought to develop universal primers for amplifying the 16S rRNA gene from a consortium of disparate microbial species. Using multiple sequence alignment of the 16S rRNA gene of a variety of microbes, the resulting highly conserved region of the consensus sequence was used for design of universal polymerase chain reaction (PCR) primers for 16S rRNA gene. Application of the universal primers in simulated PCR reveals poor amplification efficiency where only 12 species out of 31 generated an amplicon. BLAST analysis of the resulting amplicons reveals a classification error of 50%. More significantly, analysis of the amplicon length indicates variable read length ranging from 81 to 122 base pair compared to the predicted read length of 100 base pairs. This suggests that the 16S rRNA gene harbours significant hitherto underappreciated sequence diversity, and may have unknown alternative splicing and recombination mechanisms. Overall, results from this study suggests that primer design for 16S rRNA amplicon metagenomics may be application and habitat specific, where it is difficult to design universal primers for all bacterial species. Conceptually, this meant that there may be sequence co-evolution in 16S rRNA gene for microbial species in the habitat where environmental and nutritional conditions impact on 16S rRNA gene structure and sequence. In essence, 16S rRNA gene may habour epigenetics signals at the gene level.

Discussing quantum theory foundations, von Neumann noted that the measurement process should not be regarded in terms of a temporal evolution. A reason for his claim is insurmountability of the gap between reversible and irreversible processes. The time operator formalism that goes beyond such a gap is adequate framework for elaboration of the measurement problem. It considers signals to be stochastic processes, whether they correspond to variables or distribution densities. Signal processing like that utilizes statistical properties to perform its tasks, which is the definition of statistical signal processing. A hierarchy of the measurement process is indicated by crossing between states and devices, which implies an evolution in the temporal domain. The concept has generalized to an open system by the use of duality in frame theory.

The problem of event detection in general noisy signals arises in many applications; usually, either a functional form for the event is available, or a previous annotated sample with instances of the event that can be used to train a classification algorithm. There are situations, however, where neither functional forms nor annotated samples are available; then it is necessary to apply other strategies to separate and characterize events. In this work, we analyze 15 minute-long samples of an acoustic signal, and are interested in separating sections, or segments, of the signal which are likely to contain significative events. For that, we apply a sequential algorithm with the only assumption that an event alters the energy of the signal. The algorithm is entirely based on Bayesian methods.

Isothermal Nucleic Acid Amplification based-Lateral Flow Testing (INAA-LFT) has emerged as a robust technique for on-site pathogen detection, providing a visible indication of pathogen nucleic acid amplification that rivals or even surpasses the sensitivity of real-time quantitative PCR. The isothermal nature of INAA-LFT ensures consistent conditions for nucleic acid amplification, establishing it as a crucial technology for rapid on-site pathogen detection. However, despite its considerable promise, the widespread application of isothermal INAA amplification-based lateral flow testing faces several challenges. This review provides an overview of the INAA-LFT procedure, highlighting its advancements in detecting plant viruses. Moreover, the review underscores the imperative to address existing limitations and emphasizes ongoing research efforts dedicated to enhancing the applicability and performance of this technology in the realm of rapid on-site testing.

This study investigates the impact of temperature-induced quantum proton tunneling probability on DNA amplification during polymerase chain reactions (PCR). Using a simulation model based on a Gaussian wavefunction and finite-difference time-domain method, quantum tunneling of protons across square potential barriers is examined. The results unveil consistent probability distributions for quantum tunneling across various PCR temperatures, with distinct oscillation patterns emerging post-barrier crossing. Acknowledging limitations in initial conditions due to temperature-dependent proton energy, the study highlights the need for refined models and experimental validation. These findings accentuate the potential interplay between quantum mechanics and biological systems, prompting further research to understand quantum tunnelling’s comprehensive effect on genetic variations and molecular processes.

Rice false smut caused by Ustilaginoidea virens is one of the most devastating diseases on rice worldwide, which results in serious reduction of rice quality and yield. As an airborne fungal disease, early diagnosis of rice false smut, monitoring the epidemics and distribution of its pathogens, is particularly important to management the infection. In this study, a quantitative loop-mediated isothermal amplification (q-LAMP) method for the U. virens detection and quantifying was developed. This method has higher sensitivity and efficiency compared to quantitative real-time PCR (q-PCR) method. The species-specific primer sets UV-2 used was design based on the unique sequence of U. virens ustiloxins biosynthetic gene (NCBI accession number: BR001221.1). The q-LAMP assay was able to detect a concentration of 6.4 spores/mL at an optimal reaction temperature of 63.4℃ within 60 min. Moreover, the q-LAMP assay can even achieve accurate quantitative detection when there were only 9 spores on the tape. A linearized equation for the standard curve, y =-0.2866x + 13.829 (x is the amplification time, the spore number = 100.65y), was established for detection and quantifying of U. virens. In field detection applications, this q-LAMP method is more accurate and faster than traditional observation method. Collectively, this study has established a powerful and simple monitoring tool for U. virens, which provide valuable technical supports for forecast and management of rice false smut, and theoretical basis for precise fungicide application.

Although rRT-PCR is the gold standard method for SARS-CoV-2 detection, some factors, such as amplification inhibitors presence, lead to false-negative results. Here we describe differences between rRT-PCR results for SARS-CoV-2 infection in normal and diluted samples, simulating the need for dilution due to amplification inhibitors presence. Viral RNA extraction of nasopharyngeal swabs samples from 20 patients previously detected as 'Negative' and 21 patients detected as 'Positive' for SARS-CoV-2 was realized with the EasyExtract DNA-RNA (Interprise®). rRT-PCR was realized with OneStep/COVID-19 (IBMP) kit with normal and diluted (80µl of H₂O RNAse free) samples, totaling 82 tests. The results indicate that there is an average variation (ɑ < 0.05) delaying Cq between the amplification results of internal control (IC), N Gene (NG), and ORF-1ab (OF) of 1.811 Cq, 3.840 Cq, and 3.842 Cq, respectively. The extraction kit does not completely purify the inhibitor compounds, therefore non-amplification by inhibitors may occur. In this study, we obtained a 19.04% false-negative diagnosis after sample dilution, and this process reduces the efficiency of rRT-PCR to 29.80% for detecting SARS-CoV-2. Knowing the rRT-PCR standards of diluted samples can help in the identification of false-negative cases, and consequently avoid a wrong diagnosis.

Background: Dendrobium officinale is not only an ornamental plant, but also a valuable medicinal herb that is both effective and widely used in traditional Chinese medicine. However, distinguishing D. officinale from other Dendrobium species is usually a difficult task that need much time and complex technologies due to their very similar external morphologies. The aim of this study is to develop a fast, even on-spot approach to identify D. officinale. Methods: We used DNA barcode-based loop-mediated isothermal amplification (LAMP) method with species-specific LAMP primers targeting the internal transcribed spacer (ITS) region of the rDNA of D. officinale. LAMP reaction time and temperature were optimized and the specificity and sensitivity of LAMP species-specific primers were assessed. Results: This technique showed a high specificity and sensitivity to amplify the genomic DNA of D. officinale and allowed for rapid amplification (within 40 min) of the ITS region under a constant and mild temperature range of 65 °C without using thermocyclers. Besides, by using SYBR® Green I dye as the color developing agent, the color change was easily observed with naked eye. Reaction mixture containing DNA of D. officinale changed from orange to green, while the other Dendrobium species and the negative control retained original orange color. The specificity of this LAMP-based method was confirmed by testing 17 samples of D. officinale and 32 adulterant samples from other Dendrobium species. Conclusions: This LAMP-based rapid identification method does not require expensive equipment or specialized techniques and can be used in field surveys for accurate and fast on site identification.

Microwave photonic (MWP) signal processors, which process microwave signals based on photonic technologies, bring advantages intrinsic to photonics such as low loss, large processing bandwidth, and strong immunity to electromagnetic interference. Optical microcombs can offer a large number of wavelength channels and compact device footprints, which make them powerful multi-wavelength sources for MWP signal processors to realize a variety of processing functions. In this paper, we experimentally demonstrate the capability of microcomb-based MWP signal processors to handle diverse input signal waveforms. In addition, we quantify the processing accuracy for different input signal waveforms, including Gaussian, triangle, parabolic, super Gaussian, and nearly square waveforms. Finally, we analyze the factors contributing to the difference in the processing accuracy among the different input waveforms, and our theoretical analysis well elucidates the experimental results. These results provide a guidance for microcomb-based MWP signal processors when processing microwave signals of various waveforms.

The emergence of the COVID-19 pandemics prompted a fast development of novel diagnostic methods of the etiologic virus SARS-CoV-2. Methods based on CRISPR-Cas systems have been particularly promising because they can achieve a similar sensitivity and specificity to the golden standard RT-qPCR, especially when coupled to an isothermal pre-amplification step. Furthermore, they have also solved inherent limitations of RT-qPCR that impede its decentralized use and deployment in the field, such as the need for expensive equipment, high cost per reaction, and delivery of results in hours, among others. In this review, we evaluate publicly available methods to detect SARS-CoV-2 that are based on CRISPR-Cas and isothermal amplification. We critically analyze the steps required to obtain a successful result from clinical samples and pinpoint key experimental conditions and parameters that could be optimized or modified to improve clinical and analytical outputs. The COVID outbreak has propelled intensive research in a short time, which is paving the way to develop effective and very promising CRISPR-Cas systems for the precise detection of SARS-CoV-2. This review could also serve as an introductory guide to new labs delving into this technology.

Consumer preference for products made from transgenic technology has been widely studied, yet few studies exist exploring the factors influencing producers’ adoption of transgenic technology. Based on field surveys in Chinese provinces of Shanxi, Henan and Shandong, we employed a gambling experiment to capture producers’ risk preferences by estimating their risk aversion coefficients. We further estimated producers’ risk amplification and risk perception of GM technology. Using ordered logit model and Poisson model we identified the major factors influencing producers’ adoption of transgenic technology. We found the factors impacted the decision of producers from different regions in different ways. The results showed that over 60% of participants amplified the risk of transgenic crops. When there was potential risk, producers might not be rational even if they had high level of knowledge and cognition about the technology. Our results shed light on government policies aiming to increase the adoption of new technologies by producers.

Passive radar detection emerges as a pivotal method for environmental perception and target de-tection within radar applications. Leveraging its advantages, including minimal electromagnetic pollution and efficient spectrum utilization, passive radar methodologies have garnered increasing interest. In recent years, there has been an increasing selection of passive radar signal sources, and the emerging 5G has the characteristics of high frequency band, high bandwidth, and a large number of base stations, which make it have significant advantages in passive radar. Therefore, this paper introduces a passive radar target detection method based on 5G signals and designs a rotating target speed measurement experiment. In the experiment, this paper validated the method of de-tecting rotating targets using 5G signals and evaluated the measurement accuracy, providing a research foundation for passive radar target detection using 5G signals and detecting rotating targets such as drone rotors.

The cell’s capacity to integrate and respond to spatial information is a crucial feature of morphogenesis and development. The Planar Cell Polarity (PCP) pathway is a signaling mechanism, widely conserved across metazoans, providing spatial orientation along the plane of an epithelium in morphogenic processes ranging from insect wing patterning to mammalian cochleae. Although the core genes involved in the PCP pathway have been molecularly identified in the 1990s, the PCP signaling mechanism remains controversial. In this article I discuss the main players and previous models of PCP signaling reported in the literature, and propose a new model. According to it PCP is established through an homophobic signal by transmembrane protein Frizzled (Fz): 1) a Fz signal in one cell repeals Fz itself in the adjacent cell, thereby generating symmetry breaking; 2) the instructive PCP signal is conveyed through Fz interaction with atypical cadherin Flamingo (Fmi). More broadly, homophobic signaling may represent a novel mechanism for cell-cell signaling of spatial information through modulation of cell adhesion rather than canonical ligand-receptor binding.

This paper presents a study of different types of parametric signals with application to underwater acoustic communications. In all the signals, the carrier frequency is 200 kHz, which corresponds to the resonance frequency of the transducer under study and different modulations are presented and compared. In this sense, we study modulations with parametric sine sweeps (4 to 40 kHz) that represent binary codes (zeros and ones), getting closer to the application in acoustic communications. The different properties of the transmitting signals in terms of bit rate, directivity, efficiency and power needed are discussed as well.

Yaws is a skin debilitating disease caused by Treponema pallidum subspecies pertenue with most cases reported in children. World Health Organization (WHO) aims at total eradication of this disease through mass treatment of suspected cases followed by an intensive follow-up program. However, effective diagnosis is pivotal in the successful implementation of this control program. Recombinase polymerase amplification (RPA), an isothermal nucleic acid amplification technique offers a wider range of differentiation of pathogens including those isolated from chronic skin ulcers with similar characteristics such as Haemophilus ducreyi (H. ducreyi). We have developed a duplex RPA assay for the simultaneous detection of Treponema pallidum (T. pallidum) and H. ducreyi (TPHD-RPA). TPHD-RPA assay demonstrated no cross-reaction with other pathogens and enable detection of T. pallidum and H. ducreyi within 15 minutes at 42 oC. The duplex RPA assay was validated with 49 clinical samples from individuals confirmed to have yaws by serological tests. Compared with commercial multiplex real-time PCR, the TPHD-RPA assay demonstrated 94-95% sensitivity for T. pallidum and H. ducreyi confirmed samples, respectively and 100% specificity. This simple novel TPHD-RPA assay enables the rapid detection of both T. pallidum and H. ducreyi in yaws-like lesions. This test could support the yaws eradication programs by ensuring effective diagnosis as well as enable monitoring of eradication efforts success or failure and planning of follow-up interventions at the community level.

(1) Background: In nervous system information is conveyed by a sequence of action potentials, called spikes-trains. As MacKay and McCulloch proposed, spike-trains can be represented as bits sequences coming from Information Sources. Previously, we studied relations between Information Transmission Rates (ITR) carried out by the spikes, their correlations, and frequencies. Here, we concentrate on the problem of how spikes fluctuations affect ITR. (2) Methods: The Information Theory Method developed by Shannon is applied. Information Sources are modeled as stationary stochastic processes. We assume such sources as two states Markov processes. As a spike-trains' fluctuation measure, we consider the Standard Deviation sigma, which, in fact, measures average fluctuation of spikes around the average spike frequency. (3) Results: We found that character of ITR and signal fluctuations relation strongly depends on the parameter s which is a sum of transitions probabilities from no spike state to spike state and vice versa. It turned out that for smaller s (s<1) the quotient ITR\sigma has a maximum and can tend to zero depending on transition probabilities. While for s large enough (1<s) the ITR\sigma is separated from 0 for each s. Similar behavior was observed also when we replaced Shannon entropy terms in Markov entropy formula by their approximation with polynomials. We also show that the ITR quotient by Variance behaves in a completely different way. (4) Conclusions: Our results show that for large transition parameter s the Information Transmission Rate by sigma will never decrease to zero. Specifically, for 1<s<1.7 the ITR will be always, independently on transition probabilities which form this s, above the level of fluctuations, i.e. in this case we have sigma<ITR. Thus, we conclude that in a more noisy environment, to get appropriate reliability and efficiency of transmission, Information Sources with higher tendency of transition from the state no spike to spike state and vice versa should be applied.

TGF-β signaling transduces immunosuppressive biochemical and mechanical signals in the tumor microenvironment. In addition to canonical SMAD signaling, TGF-β can promote tumor growth and survival by inhibiting proinflammatory signaling and extracellular matrix remodeling. In this article, we will review how TAK1 activation lies at the intersection of proinflammatory signaling by immune receptors and anti-inflammatory signaling by TGF-β receptors. Additionally, we will discuss the role of TGF-β in the mechanobiology of cancer. Understanding how TGF-β dampens proinflammatory responses and induces pro-survival mechanical signals throughout cancer development will be critical in designing therapeutics which inhibit tumor progression while bolstering the immune response.

This comprehensive review delves into the multifaceted aspects of ERK signaling and the intricate mechanisms underlying distinct cellular fates. ERK1 and ERK2 (ERK) govern proliferation, transformation, epithelial-mesenchymal transition, differentiation, senescence, or cell death, con-tingent upon activation strength, duration, and context. The biochemical mechanisms underlying these outcomes are inadequately understood, shaped by signaling feedback and the spatial localization of ERK activation. Generally, ERK activation aligns with the Goldilocks principle in cell fate determination. Excessive or insufficient ERK activity inhibits growth, whereas moderated activation supports proliferation and survival. Unraveling the intricacies of how the degree of ERK activation dictates cell fate requires deciphering mechanisms encompassing protein stability, transcription factors downstream of ERK, and the chromatin landscape.

Separation and detection of cells and particles in a suspension are essential for various applications, including biomedical investigations and clinical diagnostics. Microfluidics realizes the miniaturization of analytical devices by controlling the motion of a small volume of fluids in microchannels and microchambers. Accordingly, microfluidic devices have been widely used in particle/ cell manipulation processes. Different microfluidic methods for particle separation include dielectrophoretic, magnetic, optical, acoustic, hydrodynamic, and chemical techniques. Dielectrophoresis (DEP) is a method for manipulating polarizable particles’ trajectories in non-uniform electric fields using unique dielectric characteristics. It provides several advantages for dealing with neutral bioparticles owing to its sensitivity, selectivity, and noninvasive nature. This review provides a detailed study on the signal-based DEP methods that use the applied signal parameters, including frequency, amplitude, phase, and shape for cell/particle separation and manipulation. Rather than employing complex channels or time-consuming fabrication procedures, these methods realize sorting and detecting the cells/particles by modifying the signal parameters while using a simple device. In addition, these methods can significantly impact clinical diagnostics by making low-cost and rapid separation possible.

The quality of cellular products used in biological research can directly impact the ability to ob-tain accurate results. Epstein-Barr virus (EBV) is a latent virus that spreads extensively world-wide, and cell lines used in experiments may carry EBV and pose an infection risk. The presence of EBV in a single cell line can contaminate other cell lines used in the same laboratory, affecting experimental results. We developed three EBV detection systems: (1) a polymerase chain reac-tion (PCR)-based detection system, (2) a recombinase polymerase amplification (RPA)-based de-tection system, and (3) a combined RPA-lateral flow assay (LFA) detection system. The mini-mum EBV detection limits were 1×103 copy numbers for the RPA-based and RPA-LFA systems and 1×104 copy numbers for the PCR-based system. Both the PCR and RPA detection systems were applied to 192 cell lines, and the results were consistent with those obtained by the EBV assay methods specified in the pharma-ceutical industry standards of the People's Republic of China. 10 EBV-positive cell lines were identified. The combined RPA-LFA system is simple to operate, allowing for rapid results visualization. This system can be implemented in laborato-ries and cell banks as part of a daily quality control strategy to ensure cell quality and experi-mental safety and may represent a potential new technique for the rapid detection of EBV in clinical samples.

SARS-CoV-2 is a novel betacoronavirus and the aetiological agent of the current COVID-19 outbreak that originated in Hubei Province, China. While polymerase chain reaction is the front-line tool for SARS-CoV-2 surveillance, application of amplification-free and culture-free methods for isolation of SARS-CoV-2 RNA, partnered with next-generation sequencing, would provide a useful tool for both surveillance and research of SARS-CoV-2. We here release into the public domain a set of bait capture hybridization probe sequences for enrichment of SARS-CoV-2 RNA from complex biological samples. These probe sequences have been designed using rigorous bioinformatics methods to provide sensitivity, accuracy, and minimal off-target hybridization. Probe design was based on existing, validated approaches for detecting antimicrobial resistance genes in complex samples and it is our hope that this SARS-CoV-2 bait capture platform, once validated by those with samples in hand, will be of aid in combating the current outbreak.

Osteoarthritis and rheumatoid arthritis are common cartilage and joint diseases that globally affect more than 200 and 20 million people, respectively. Several transcription factors have been implicated in the onset and progression of osteoarthritis, including Runx2, C/EBPβ, HIF2α, Sox4, and Sox11. IL-1β also leads to osteoarthritis through NF-ĸB, IκBζ, and Zn²⁺-ZIP8-MTF1 axis. IL-1, IL-6, and TNFα play a major pathological role in rheumatoid arthritis through NF-ĸB and JAK/STAT pathways. Indeed, inhibitory reagents for IL-1, IL-6, and TNFα provide clinical benefits for rheumatoid arthritis patients. Several growth factors, such as BMP, FGF, PTHrP, and Indian hedgehog, play roles regulating chondrocyte proliferation and differentiation. Disruption and excess of these signaling cause genetic disorders in cartilage and skeletal tissues. FOP, an autosomal genetic disorder characterized by ectopic ossification, is induced by mutant ACVR1. mTOR inhibitors were found to prevent ectopic ossification by ACVR1 mutations. ACH and related diseases are autosomal genetic diseases, which manifest severe dwarfism. CNP is currently the most promising therapy for ACH. In these ways, investigation of cartilage and chondrocyte diseases at molecular and cellular levels sheds light on the development of effective therapies. Thus, identification of signaling pathways and transcription factors implicated in these diseases is important.

Equines play an important role throughout the world, whether for work, culture, or leisure, providing an ever-growing significant contribution on the economy. The increase in importation and movement of horses, both nationally and internationally, has inevitably allowed for the global equine industry to grow. Subsequently however, the potential for transmission of fatal equine bacterial diseases has also escalated, and devasting outbreaks continue to occur. To prevent such events, disease surveillance and diagnosis must be heightened throughout the industry. Current common, or "gold-standard" techniques, have shown to be inadequate at times, thus requiring newer technology to impede outbreaks. Loop-mediated isothermal amplification (LAMP) has proven to be a reliable, rapid, and accessible tool in both diagnostics and surveillance. This review will discuss equine bacterial diseases of biosecurity relevance and their current diagnostic approaches, as well as their respective LAMP assay developments. Additionally, we will provide insight regarding newer technology and advancements associated with this technique, and their potential use for the outlined diseases.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

This paper addresses the problem of low accuracy of conventional channel estimation and signal detection in complex fields like mines; and the problem of replacing the deep receiver at the receiver side with a deep neural network requires a large amount of data for training and slow training time. Combining the receiver side with traditional communication knowledge, a channel estimation and signal detection method based on the joint ReEsNet and SDRNet under the mine is proposed. The detailed step is to use ReEsNet network for interpolation of conventional channel estimation. Then, on the basis of ReEsNet, the output data is channel equalized and pilots removed, and the previously processed data is input to SDRNet to perform signal recovery. In the complex mine environment, the MSE values are 2e-2 for LS, 6e-3 for MMSE, and 8.44e-5 for ReEsNet at the 1500th sample data for interpolation compared to the conventional channel estimation. the MSE of ReEsNet is the smallest and is closer to the real channel estimation. Compared with the proposed joint channel estimation and signal detection methods, fewer trainable parameters reduce 97% of the parameters compared to CCRNet and 84% of the parameters compared to CNNNet; their detection results, however, are not very different.

In this contribution a new configuration of a DC-DC Boost and Buck-Boost converters is proposed to track sinusoidal signals exactly, with zero tracking error. The stage is conformed by two DC-DC converters connected to the same load, this is, they are not connected in cascade. To track exactly the sinusoidal reference the control scheme is base on the indirect control algorithm and the harmonic balance method. The proposed algorithm considers a second control input with the end of cancel out the second harmonic, this second harmonic is produced by the non linearity of the model and must be cancelled since there must be a single frequency in the output. The result is such that the converters can track sinusoidal signals with exactly zero error, some numerical results are presented to corroborate the proposal.

Epilepsy is a neurological disorder that affects approximately 1% of the world's population. To diagnose and estimate the occurrence of epilepsy, the analysis of recorded brain activity is performed by a neurologist, which is not only time-consuming and tedious but also occasionally accompanied by human error. Therefore, in recent decades, researchers have aimed to unravel an approach for designing and building an automated method for diagnosing and estimating the occurrence of epilepsy. Accordingly, the present study proposed two new-fangled ways based on brain signals and a convolutional neural network (CNN). Moreover, this research implements a CNN with a sequential three-layer structure. Numerous experiments were performed, and the accuracy of estimating epilepsy using the developed methods was achieved at 95% without feedback and 97% with feedback. The proposed methods were proven to be more accurate than the previous techniques and can be employed as a physician's assistant once entering the field of operation.

Migratory flows and international travel are triggering an increase in imported cases of schistosomiasis in non-endemic countries, with serology being the recommended method for screening migrants. The present study aims to evaluate, for the first time, the LAMP technique on patients’ urine samples for the diagnosis of imported schistosomiasis in a non-endemic area in comparison to a commercial immunochromatographic test and microscopic examination of feces and urine. A prospective observational study was conducted in sub-Saharan migrants attending at the Tropical Medicine Unit, Almería, Spain. For schistosomiasis diagnosis, serum samples were tested using an immunochromatographic test (Schistosoma ICT IgG-IgM). Stool and urine samples were examined by microcopy. Urine samples were evaluated by combining three LAMP assays for the specific detection of Schistosoma mansoni and S. haematobium, and an assay for the genus Schistosoma. To evaluate the diagnostic accuracy of Schistosoma-LAMP in comparison to microscopy and Schistosoma ICT IgG-IgM test, a Latent Class Analysis (LCA) was performed. A total of 115 patients were included; 21 patients (18.3%) were diagnosed with schistosomiasis confirmed by microscopy, with S. haematobium being the most frequent species identified (18/115; 15.7%). The Schistosoma ICT IgG-IgM test resulted 100% positive and Schistosoma-LAMP was 61.9% positive, reaching as high as 72.2% for S. haematobium. The sensitivity and specificity estimated by LCA, respectively, were: 92% and 76% for Schistosoma ICT IgG-IgM, 68% and 44% for Schistosoma-LAMP and, 46% and 97% for microscopy. The Schistosoma-LAMP technique presented a higher sensitivity than microscopy for the diagnosis of imported urinary schistosomiasis, which could improve the diagnosis both in referral centers and in centers with limited experience or scarce resources and infrastructure.

The transfer of protein-encoding genetic information from DNA to RNA to protein, a process formalized as the “Central Dogma of Molecular Biology”, has undergone a significant evolution since its inception. It was amended to account for the information flow from RNA to DNA, the reverse transcription, and for the information transfer from RNA to RNA, the RNA-dependent RNA synthesis. These processes, both potentially leading to protein production, were initially described only in viral systems, and although RNA-dependent RNA polymerase activity was shown to be present, and RNA-dependent RNA synthesisfound to occur, in mammalian cells, its function was presumed to be restricted to regulatory. However, recent results, obtained with multiple mRNA species in several mammalian systems, strongly indicate the occurrence of protein-encoding RNA to RNA information transfer in mammalian cells. It can result in the rapid production of the extraordinary quantities of specific proteins as was seen in cases of terminal cellular differentiation and during cellular deposition of extracellular matrix molecules. A malfunction of this process may be involved in pathologies associated either with the deficiency of a protein normally produced by this mechanism or with the abnormal abundanceof a protein or of its C-terminal fragment. It seems to be responsible for some types of familial thalassemia and may underlie the overproduction of beta amyloid in sporadic Alzheimer’s disease. The aim of the present article is to systematize the current knowledge and understanding of this pathway. The outlined framework introduces unexpected features of the mRNA amplification such as its ability to generate polypeptides non-contiguously encoded in the genome, its second Tier, a physiologically occurring intracellular polymerase chain reaction, iPCR, a Two-Tier Paradox and RNA Dark Matter. RNA-dependent mRNA amplification represents a new mode of genomic protein-encoding information transfer in mammalian cells. Its potential physiological impact is substantial, it appears relevant to multiple pathologies and its understanding opens new venues of therapeutic interference, it suggests powerful novel bioengineering approaches and its further rigorous investigations are highly warranted.

Alzheimer's Disease (AD) is a neurodegenerative disease that is common in the elderly. This paper introduces the overview of Alzheimer's disease and the application of relevant signal processing methods in its detection. Signal processing is a technique that converts raw data into meaningful information and is widely used in the medical field. This paper lists common signal processing techniques, including Fourier transform, time-frequency analysis and statistical signal processing, and discusses their applications in the detection of Alzheimer's disease. Fourier transform can convert time domain signals into frequency domain representations, providing an effective tool for the study of EEG in Alzheimer's disease. Time-frequency analysis can perform a combined time and frequency analysis of the signal to help detect the signal characteristics of Alzheimer's disease. Statistical signal processing methods can be used to identify the features of Alzheimer's disease by building mathematical models. Finally, the challenges of Alzheimer's disease detection are discussed, including signal noise, diversity, and insufficient data volume. Through in-depth research and development of signal processing methods, it is expected to improve the accuracy and efficiency of early detection of Alzheimer's disease.

This paper demonstrates an on-off keying (OOK) super-regenerative quenching transmitter operating in 402- 405MHz MICs band applications. To reduce power consumption, the transmitter is controlled by a novel digital quenching signal controller that generates a digital control signal to start transmitter operation when a baseband signal is input to the transmitter. The digital signal controller consists of an envelope detector, a comparator, and a quench timer designed using a state machine to synchronize the operation between the digital controller and the input baseband signal. The transmitter consists of a Colpitts oscillator operating in double operating frequency followed by a frequency divider by 2, this configuration reduces system area and improves phase noise and signal spectrum. The proposed transmitter is implemented using UMC 130nm CMOS technology, and a 1.2V supply. Simulation shows that the proposed transmitter can meet MICS band mask specifications with data rates up to 1Mbps and total power dissipation of 537uW.

The great Greek philosopher Aristotle (384–322 BCE) is almost unanimously acclaimed as the founder of zoology. There is a consensus that he was interested in attributes of animals, but whether or not he tried to develop a zoological taxonomy remains controversial. Fürst von Lieven and Humar compiled a data matrix and showed, through a parsimony analysis published in 2008, that these data produced a hierarchy that matched several taxa recognized by Aristotle. However, their analysis leaves some questions unanswered because random data can sometimes yield fairly resolved trees. In this study, we update the scores of many cells and add four new characters to the data matrix (147 taxa scored for 161 characters) and quote passages from Aristotle’s Historia animalium to justify these changes. We confirm the presence of a phylogenetic signal in these data through a test using skewness in length distribution of a million random trees, which shows that many of the characters discussed by Aristotle were systematically relevant. Our parsimony analyses on the updated matrix recover far more trees than reported by Fürst von Lieven and Humar, but their consensus includes many taxa that Aristotle recognized and apparently named for the first time, such as selachē (selachians) and dithyra (Bivalvia). This study suggests that even though taxonomy was clearly not Aristotle’s chief interest in Historia animalium, it was probably among his secondary interests. These results may pave the way for further taxonomic studies in Aristotle’s zoological writings in general. Despite being almost peripheral to Aristotle’s writings, his taxonomic contributions are clearly major achievements.

In the last decade, unprecedented progress in the development of neural networks influenced dozens of different industries, among which are signal processing for the electroencephalography process (EEG). Electroencephalography, even though it appeared in the first half of the 20th century, to this day didn’t change the physical principles of operation. But the signal processing technique due to the use of neural networks progressed significantly in this area. Evidence for this can serve that for the past 5 years more than 1000 publications on the topic of using machine learning have been published in popular libraries. Many different models of neural networks complicate the process of understanding the real situation in this area. In this manuscript, we provided the most comprehensive overview of research where were used neural networks for EEG signal processing.

This paper develops a two-layer optimization approach that provides energy-optimal control for vehicles and traffic signal controllers. The optimizer in the first layer computes the traffic signal timings to minimize the total energy consumption levels of approaching vehicles from upstream traffic. The traffic signal optimization can be easily implemented in real-time signal controllers, and it overcomes the issues in the traditional Webster’s method of overestimating the cycle length when the traffic volume-to-capacity ratio exceeds 50 percent. The second layer optimizer is the vehicle speed controller, which calculates the optimal vehicle brake and throttle levels to minimize the energy consumption of individual vehicles. The A-star dynamic programming is used to solve the formulated optimization problem in the second layer to expedite the computation speed so that the optimal vehicle trajectories can be computed in real-time and can be easily implemented in simulation software for testing. The proposed integrated controller is first tested on an isolated signalized intersection, and then an arterial network with multiple intersections to investigate the performance of the proposed controller under various traffic demand levels. The test results demonstrate that the proposed integrated controller can greatly improve energy efficiency with fuel savings up to 17.7%, at the same time enhancing traffic mobility by up to 47.18% reduction in traffic delay and up to 24.84% reduction in vehicle stops.

The Combined Theoretical Signal (CTS) model, with a 90% or higher validity rate, stands as the first validated universal model integrating gravity and quantum physics. This manuscript presents the final validation and enhancement of the CTS model using recent pulsar-sourced gravitational wave data (J2322+2057, J2234+0611, J2043+1711, and J2317+1439) and strain data from GW150914, GW151226, GW190521, and GW200105. Our findings demonstrate a significant alignment between theoretical predictions and observational data, positioning CTS as a groundbreaking framework with profound implications for theoretical physics and cosmology. The CTS model not only bridges the gap between gravity and quantum mechanics but also offers a new perspective on the formation of massive black holes, the Quantum Cosmic Fabric (QCF), and the structure of the universe as an interconnected hierarchical tree of universes.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

The increasing focus on the development of positioning techniques reflects the growing interest in applications and services based on indoor positioning. Many applications necessitate precise indoor positioning or tracking of individuals and assets, leading to rapid growth in products based on these technologies in certain market sectors. Ultrasonic systems have already proven effective in achieving the desired positioning accuracy and refresh rates. The typical signal used in ultrasonic positioning systems for estimating the range between the target and reference points, specifically the linear chirp, can undergo shape aberration due to the effects of acoustic diffraction when the aperture exceeds a certain limit. The extent of the aberration is influenced by the shape and size of the transducer, as well as the angle at which the transducer is observed by the receiver. This aberration also impacts the shape of the cross-correlation, causing it to lose its characteristic easily detectable single global peak. In such instances, cross-correlation techniques yield results with a significantly higher error than anticipated. In this study, an alternative technique to global peak detection is proposed, leveraging the inherent symmetry observed in the shape of the aberrated cross-correlation. The numerical simulations, performed using the academic acoustic simulation software Field II, conducted using a typical ultrasonic chirp and ultrasonic emitter, compare the classical and the proposed range techniques in a standard office room. The results demonstrate that the proposed technique enables accurate range estimation even in the presence of severe cross-correlation shape aberrations. This allows the use of emitting transducers with a much larger aperture than that allowed by the classical cross-correlation technique. Consequently, it becomes possible to have greater acoustic power available, leading to improved Signal-to-Noise Ratio (SNR).

Orthogonal Frequency Division Multiplexing (OFDM) is a technique widely used in today's wireless communication systems due to its ability to combat the effects of multi-path in the signal. However, one of the main limitations of the use of OFDM is its high Peak-to-Average Power Ratio (PAPR), which reduces the efficiency of the OFDM system. The effects of PAPR can produce both out-of-band and in-band radiation, which degrades the signal by increasing the bit error rate (BER), this occurs in both baseband and bandpass sginals. In this document the effect of the PAPR in a OFDM passband signal is analyzed considering the implementation of a High Power Amplifier (HPA) and the Simple Amplitude Predistortion-Orthogonal Pilot Sequences (OPS-SAP) scheme to reduce the PAPR.

Directional Modulation (DM) technique, as an emerging promising approach to secure wireless communications, has been attracting increasing attention for its unique characteristic in the past decade. The baseband signal is synthesized at the antenna level for maintaining the standard constellation format along the prescribed direction(s) while simultaneously distorting the signal constellations in other undesired directions. In this paper, we present a novel DM signal synthesis method based on phased array using a hybrid genetic algorithm (GA) and particle swarm optimization (PSO) algorithm, which takes advantages of both GA and PSO algorithm. Then, the bit error rate of the proposed method is analyzed and simulated. Simulation results are presented to verify that the proposed DM signal have a narrower information beam-width. Therefore, it can offer a better physical layer security (PLS) performance compared with the conventional directional modulation signal.

Sensor fusion technology is one of extensive used methods in the field of robot, aerospace and target tracking control. In this paper, the generalized sensor fusion framework, named the closed-loop fusion (CLF) is analyzed and the optimal design principle of filter is proposed in detail. Fusion error optimization problem, which is the core issue of fusion design, is also solved better through the feedback compensation law of CLF framework. Differently from conventional methods, the fusion filter of CLF can be optimally designed and the determination of superposition of fusion information is avoided. To show the validity, simulation and experimental results are to be submitted.

Search for periodic signals from blazars has become widely discussed topic in recent years. This is because periodic signals bear imprints of the processes occurring near the innermost regions of blazars which are mostly inaccessible to our direct view. Such signals provide insights into various aspect of blazar studies including disk-jet connection, magnetic field configuration and, more importantly, strong gravity near the supermassive black holes and release of gravitational waves from the binary supermassvie black hole systems. In this work, we report detection of a periodic signal in the radio light curves of the blazar J1043+2408 spanning ~10.5 years. We performed multiple methods of time series analysis, namely, epoch folding, Lomb-Scargle periodogram, and discrete auto-correlation function. All three methods consistently reveal a repeating signal with a periodicity of ~563 days. To robustly account for the red-noise processes usually dominant in the blazar variability and other possible artifacts, a large number of Monte Carlo simulations were performed. This allowed us to estimate a high significance (99.9% local and 99.4% global) against possible spurious detection. As possible explanations, we discuss a number of scenarios including binary supermassive black hole system, Lense-Thirring precession, and jet swing and precession.

The upregulated expression of thyrosine kinase AXL has been reported in several hematologic and solid human tumors including gastric, breast, colorectal, prostate, and ovarian cancers. Thus, AXL can potentially serve as a diagnostic and prognostic biomarker for various cancers. This paper reports the first-ever use of loop-mediated isothermal amplification (LAMP) of the AXL gene as a diagnostic method for ovarian cancer. We demonstrated simple instrumentation toward a point-of-care device to perform LAMP. This paper also reports the first-ever use of core-shell beads as a microreactor to perform LAMP as an attempt to promote environmentally friendly laboratory practices.

The current coronavirus disease 2019 (COVID-19) pandemic is largely driven by community transmission, after 2019 novel Coronavirus (2019-nCoV or SARS-CoV-2) crosses the borders. To stop the spread, rapid testing is required at community clinics and hospitals. These rapid tests should be comparable with the standard PCR technology. Isothermal amplification technology provides an excellent alternative that is highly amenable to resource limited settings, where expertise and infrastructure to support PCR are not available. In this review, we provide a brief description of isothermal amplification technology, its potential and the gaps that need to be considered for SARS-CoV-2 detection. Among this emerging technology, loop mediated amplification (LAMP) and recombinase polymerase amplification (RPA) technologies have been identified as potential platforms that could be implemented at community level, without samples referral to a centralised laboratory and prolonged turn-around-time associated with the standard COVID-19 RT-PCR test. LAMP, for example, has recently been shown to be comparable with PCR and could be performed in less than 30 min by non-laboratory staff, without RNA extractions commonly associated with PCR. More so, it is cost effective and could easily be scaled up to resource limited settings. Diagnostics developers, scientific community and commercial companies could consider this alternative method to help stop the spread of COVID-19.

Analysis of non-stationary and nonlinear sound signals obtained from dynamical processes is one of the greatest challenges in signal processing. Turning machine operation is a highly dynamic process persuaded by many events such as dynamical responses, chip formations and operational conditions of machining. Traditional and widely used fast Fourier transformation and spectrogram is not suitable for processing sound signals acquired from dynamical systems as its result have significant deficiencies because of stationary assumptions and having priori basis. The relatively new technique, Discrete Wavelet Transform, which uses Wavelet decomposition and the recently developed technique, Hilbert Huang Transform (HHT) which uses Empirical Mode Decomposition have notably better properties in the analysis of nonlinear and non-stationary sound signals. This paper presents a comparative study on the decomposition of multicomponent sound signals using Empirical Mode Decomposition and Wavelet Decomposition to highlight the suitability found in HHT to analyze tool-emitted sound signals received from turning processes. Apart from the short mathematical and theoretical foundations of the transformations, this paper demonstrates their decomposition strength using an experimental case study of tool flank wear monitoring in turning. It also concludes HHT is more suitable than DWT to analyze tool-emitted sound signals received from turning processes.

Integrated Kerr micro-combs, a powerful source of many wavelengths for photonic RF and microwave signal processing, are particularly useful for transversal filter systems. They have many advantages including a compact footprint, high versatility, large numbers of wavelengths, and wide bandwidths. We review recent progress on photonic RF and microwave high bandwidth temporal signal processing based on Kerr micro-combs with spacings from 49-200GHz. We cover integral and fractional Hilbert transforms, differentiators as well as integrators. The potential of optical micro-combs for RF photonic applications in functionality and ability to realize integrated solutions is also discussed.

To date electric pianos and samplers tend to concentrate on authenticity in terms of temporal and spectral aspects of sound. They barely recreate the original sound radiation characteristics, contribute to the perception of width and depth, vividness and voice separation, especially for instrumentalists, who are located in the near field. This paper describes an operational procedure to measure, store, and synthesize the complete sound of a harpsichord, including its spatial sound radiation characteristics. First, actuators excite the instrument at the intersection point of each string with the bridge with an exponential sine-sweep. Then, the radiated sound field is recorded in the near and the far field with microphone arrays. The pressure distribution in the near field is propagated back to the soundboard of the instrument, using Minimum Energy Method. The vibration of each single string is captured with lightweight contact microphones. The soundboard is then replaced by an array of 128 loudspeakers. The loudspeaker signal is a convolution of the back-propagated sweep recording with the string recording to perform a wave field synthesis. Above the spatial Nyquist frequency, the Radiation Method is applied to perform a sound field synthesis which is valid for the listening region of the instrumentalist. The result is an electric harpsichord, that approximates the sound of a real harpsichord precisely in time, frequency, and space domain. Applications for such a radiation keyboard are music performance, instrument and synthesizer building and interactive psychoacoustic research.

In the southeastern coast of Brazil, the bays of Ilha Grande and Sepetiba are linked by the Ilha Grande Channel, where remarkably vigorous currents have been consistently observed. The sheer intensity of these currents defies a simple explanation through tidal forcing alone, prompting researchers to delve into potential influences such as basin resonance and the baroclinic effect. This study aims to elucidate the role of remote meteorological effects within this complex hydrodynamic system. A numerical approach with a coastal model nested within an ocean model was employed, enabling an in-depth examination of the intricate interplay between meteorological and tidal forcings. The study revealed a significant finding: the lag in signal propagation plays a pivotal role in determining how these signals impact the dynamics of the bays. The astronomical signal exhibits a minimal lag along the coast (1 minute), and leads to water level differences between the sea and the coastline, resulting in the generation of tidal currents at the bay entrances. On the other hand, the remote meteorological signal, with a stronger signal lag along the coast (4.92 hours), leads to the creation of water level difference between the bay’s entrances, inducing significant fluxes along the narrow Ilha Grande Channel.

The availability of simple SARS-CoV-2 detection methods is crucial to contain the COVID-19 pandemic. This study examined whether a commercial LAMP assay can reliably detect SARS-CoV-2 genomes directly in respiratory samples without having to extract nucleic acids (NA) beforehand. Nasopharyngeal swabs (NPS, n = 220) were tested by real-time reverse transcription (RT)-PCR and with the LAMP assay. For RT-PCR, NA were investigated. For LAMP, NA from 26 NPS in viral transport medium (VTM) were tested. The other 194 NPS were analyzed directly without prior NA extraction [140 samples in VTM; 54 dry swab samples stirred in phosphate buffered saline]. Ten NPS were tested directly by LAMP using a sous-vide cooking unit. The isothermal assay demonstrated excellent specificity (100%) but moderate sensitivity (68.8%), with a positive predictive value of 1 and a negative predictive value of 0.65 for direct testing of NPS in VTM. The use of dry swabs, even without NA extraction, improved the analytical sensitivity; up to 6% of samples showed signs of inhibition. The LAMP could be performed successfully with a sous-vide cooking unit. This technique is very fast, requires little laboratory resources and can replace rapid antigen tests or verify reactive rapid tests on site.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

Photoplethysmography (PPG) is widely utilized in wearable healthcare devices due to its convenient measurement capabilities. However, the unrestricted behavior of users often introduces artifacts into the PPG signal. As a result, signal processing and quality assessment play a crucial role in ensuring that the information contained in the signal can be effectively acquired and analyzed. Traditionally, researchers have discussed signal quality and processing algorithms separately, with individual algorithms developed to address specific artifacts. In this paper, we propose a quality-aware signal processing mechanism that evaluates incoming PPG signals using signal quality index (SQI) and selects the appropriate processing method based on the SQI. Unlike conventional processing approaches, our proposed mechanism recommends processing algorithms based on the quality of each signal, offering an alternative option for designing signal processing flows. Furthermore, our mechanism achieves a favorable trade-off between accuracy and energy consumption, which are the key considerations in long-term heart rate monitoring.

Microwave photonic (MWP) transversal signal processors offer a compelling solution for realizing versatile high-speed information processing by combining the advantages of reconfigurable electrical digital signal processing and high-bandwidth photonic processing. With the capability of generating a number of discrete wavelengths from micro-scale resonators, optical microcombs are powerful multi-wavelength sources for implementing MWP transversal signal processors with significantly reduced size, power consumption, and complexity. By using microcomb-based MWP transversal signal processors, a diverse range of signal processing functions have been demonstrated recently. In this paper, we provide a detailed analysis for the processing inaccuracy that are induced by the imperfect response of experimental components. First, we investigate the errors arising from different sources including imperfections in the microcombs, the chirp of electro-optic modulators, chromatic dispersion of the dispersive module, shaping errors of the optical spectral shapers, and noise of the photodetector. Next, we provide a global picture quantifying the impact of different error sources on the overall system performance. Finally, we introduce feedback control to compensate the errors caused by experimental imperfections and achieve significantly improved accuracy. These results provide a guide for optimizing the accuracy of microcomb-based MWP transversal signal processors.

Soliton crystal micro-combs are powerful tools as sources of multiple wavelength channels for radio frequency (RF) signal processing. They offer a compact device footprint, large numbers of wavelengths, very high versatility, and wide Nyquist bandwidths. Here, we demonstrate integral order RF signal processing functions based on a soliton crystal micro-comb, including a Hilbert transformer and first- to third-order differentiators. We compare and contrast results achieved and the tradeoffs involved with varying comb spacing, tap design methods, as well as shaping methods.

Wideband signal detection is an important problem in wireless communication. With the rapid development of deep learning (DL) technology, some DL-based methods are applied to wireless technology, and the effect is obvious. In this paper, we propose a novel neural network for multi-type signal detection that can locate signals and recognize signal types in wideband spectrogram. Our network utilizes the key point estimation to locate the rough centerline of signal region and identify class. Then, several regressions are carried out to achieve properties, such as local offset and border offsets of bounding box, which is further synthesized for a more fine location. Experimental results demonstrate that our method performs more accurate than other DL-based object detection methods previously employed for the same detection task. Specifically, our method runs obviously faster than existing methods, and abandons the anchor generation, which makes it more favorable for real-time applications.

There is increasing interdisciplinary interest in phytoplankton community dynamics as the growing environmental problems of water quality (particularly eutrophication) and climate change demand attention. This has led to a pressing need for improved biophysical and causal understanding of Phytoplankton Functional Type (PFT) optical signals, in order that satellite radiometry may be used to detect ecologically relevant phytoplankton assemblage changes. This understanding can best be achieved with biophysically and biogeochemically consistent phytoplankton Inherent Optical Property (IOP) models, as it is only via modelling that phytoplankton assemblage characteristics can be examined systematically in relation to the bulk optical waterleaving signal. The Equivalent Algal Populations (EAP) model is used here to investigate the source and magnitude of size- and pigment- driven PFT signals in the water-leaving reflectance, as well as the potential to detect these using satellite radiometry. This model places emphasis on explicit biophysical modelling of the phytoplankton population as a holistic determinant of IOPs, and a distinctive attribute is its comprehensive handling of the spectral and angular character of phytoplankton scattering. Selected case studies and sensitivity analyses reveal that phytoplankton spectral scattering is the primary driver of the PFT-related signal. Key findings are that the backscattering-driven signal in the 520 to 600 nm region is the critical PFT identifier at marginal biomass, and that while PFT information does appear at blue and red wavelengths, it is compromised by biomass/gelbstoff ambiguity in the blue and low signal in the red, due primarily to absorption by water. These findings are hoped to provide considerable insight into the next generation of PFT algorithms.

This work presents a methodology for the generation and classification of phase resolved partial discharges (PRPD) patterns based on the use of a printed UHF monopole antenna and signal con-ditioning circuit to reduce hardware requirements. For this purpose, envelope detection technique was applied. In addition, test objects such as a hydrogenerator bar, dielectric disks with internal cavities in an oil cell, potential transformer, and tip-tip electrodes immersed in oil were used to generate partial discharge (PD) signals. To detect and classify partial discharges, the standard IEC 60270 (2000) method was used as reference. After acquisition of conditioned UHF signals, digital signal filtering threshold technique was used, and peaks of partial discharges envelopes pulses were extracted. Feature selection techniques were used to classify the discharges and choose the best features to train machine learning algorithms, such as multilayer perceptron, support vector ma-chine and decision tree. Accuracies greater than 84% were met, revealing the classification potential of the methodology proposed in this work.

Fluorescent labels, especially FRET probes, are promising tools for studying a number of bio-chemical processes. In this paper, we promoted 2 important applications of FRET probes (MUTMAC-R6G and FITC-R6G): i) the formation of micelles from surfactants of various natures and polymers (chitosan – fatty acid), as well as ii) monitoring of enzymatic activity with improved parameters (increased analytical signal and improved selectivity due to shift to the long-wavelength region). The formation of micelles is accompanied by the convergence of fluorophores in the hydrophobic micelle core by a distance closer than in the buffer solution, thus r/R0 (where R0 – Foerster radius) is chosen as an analytical signal of micelle formation, including critical micelle concentration (CMC) and critical pre-micelle concentration (CPMC). The CMC values calculated using FRET probes are in a good agreement with literature data. At the same time, the r/R0 function provides valuable information about the nature and mechanism of micelle formation. With the second analytical application of FRET probes, we considered the optimization of techniques for studying enzymatic activity. The enzyme catalyses the reaction with the release of a fluorescent product, the signal from which may not be enough for detection, or it may be quenched, for example, in the reverse micelles (AOT-octane). Here we have proposed a solution – a FRET probe containing a rhodamine 6G (R6G) acceptor, which allows us to monitor the enzymatic reaction selectively (in the red region, 550-600 nm), and obtain a significantly higher fluorescence yield (potentially from 10 to 250 times). Thus, we have demonstrated a high potential for the FRET probes application as indicators of micelle formation as well as for the study of the enzyme catalytic activity. In the future, the method developed has prospects for application in the visualization of the enzyme functioning in cells due to the shift of the fluorescence signal to the long-wavelength region with an increase in the signal selectivity to suppress autofluorescence.

Traffic congestion is a persistent and challenging problem in urban areas, leading to increased travel times, fuel consumption, and environmental pollution. Signalized intersections play a pivotal role in regulating traffic flow, and their efficiency has a direct impact on the overall traffic performance of a city. This study investigates the effect of traffic signal in managing traffic volume and reducing congestion and delays at signalized intersections through a comprehensive analysis of existing research, data collection, and simulations.The research begins by analyzing the traffic characteristics by an installed LiDAR sensor at E Cold Spring Ln – Hillen Rd intersection in Baltimore City, MD. When the signal at this intersection stopped working for some hours during a working day in September 2023, the LiDAR recorded vehicle and pedestrian counts, vehicle-vehicle and vehicle-pedestrian conflicts, and jaywalking events conflicts. The research aims to assess the impact of traffic signal failures on traffic flow, congestion, safety (V2V and V2P conflicts), and the frequency of jaywalking events before, during, and after improper performance of the traffic signal. Furthermore, this study explores the factors influencing traffic signal performance, including traffic demand, geometric layout, pedestrian interactions, and the integration of emerging technologies. The analysis results highlighted the importance of signal control systems existence at this intersection that can adjust signal timing in response to changing the real-time traffic conditions.Reduced congestion, minimized delays, and enhanced traffic flow are observed outcomes, contributing to a more sustainable and efficient urban transportation system. However, it is crucial to consider the trade-offs and challenges associated with traffic signal optimization, such as the potential for increased travel times for certain modes of transportation and the need for ongoing maintenance and updates. In conclusion, this study underscores the pivotal role of traffic signals in managing traffic volume and reducing congestion and delays at signalized intersections. Through evidence-based analysis and innovative signal control strategies, urban planners and transportation authorities can work towards creating more efficient, sustainable, and less congested transportation networks. The insights derived from this research can inform policy decisions and guide the development of future traffic management solutions, ultimately leading to improved quality of life in urban areas.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

The objective of this study was to evaluate the efficacy of one-step nucleic acid amplification (OSNA) for the detection of sentinel lymph node (SLN) metastasis compared to standard pathological ultrastaging in patients with early-stage endometrial cancer (EC). A total of 526 SLNs from 191 patients with EC were included in the study. 379 SLNs (147 patients) were evaluated by both methods, OSNA and standard pathological ultrastaging. The central 1-mm portion of each lymph node was subjected to semi-serial sectioning at 200-μm intervals and examined by hematoxylin-eosin and immunohistochemistry with CK19; the remaining tissue was analysed by OSNA for CK19 mRNA. The OSNA assay detected metastases in 19.7% of patients (14.9% micrometastasis and 4.8% macrometastasis), whereas pathological ultrastaging detected metastasis in 8.8% of patients (3.4% micrometastasis and 5.4% macrometastasis). Using the established cut-off value for detecting SLN metastasis by OSNA in EC (250 copies/μl), the sensitivity of the OSNA assay was 92%; specificity was 82%; diagnostic accuracy was 83%, and the negative predictive value was 99%. Discordant results between both methods were recorded in 20 patients (13.6%). OSNA resulted in an upstaging in 12 patients (8.2%). OSNA could aid in the identification of patients requiring adjuvant treatment at the time of diagnosis.

The occurrence of chaotic instability of oscillations at the output of a single-stage amplifier on a powerful bipolar microwave transistor when a biharmonic signal is amplified is considered. It has been established that at a high level of the input signal at the output of the amplifier, the signal contains a significant chaotic component. Cases were experimentally studied when the frequency distance between the partial frequency components of a biharmonic signal is close to the gain band and when it is much smaller than this band. It has been established that in the first case, the chaos in oscillations is associated with the emergence of a sequence of trains of a forced oscillatory process with arbitrary initial phases and durations. In the second case, the appearance of a chaotic pedestal is associated with the chaos in the passive underexcited mode of the nonlinear circuit formed by the capacitance of the p-n junction and the input matching circuits of the amplifier stage.

Recurrent neural networks (RNNs) transmit information over time through recurrent connections. In contrast, biological neural networks use many other temporal processing mechanisms. One of these mechanisms is the inter-neuron delays caused by varying axon properties. Recently, this feature was implemented in echo state networks (ESNs), a type of RNN, by assigning spatial locations to neurons and introducing distance-dependent inter-neuron delays. These delays were shown to significantly improve ESN task performance. However, thus far it is still unclear why distance-based delay networks (DDNs) perform bettern than ESNs. In this paper, we show that by optimizing inter-node delays, the memory capacity of the network matches the memory requirements of the task. As such, networks concentrate their memory capabilities to the points in the past which contain the most information for the task at hand. Moreover, we show that DDNs have more total linear memory capacity, with the same amount of non-linear processing power.

In urban Vehicular Ad Hoc Network (VANET) environments, buildings play a crucial role as they can act as obstacles that attenuate the transmission signal between vehicles. Quantifying the impact of buildings on the transmission quality is essential, especially in critical scenarios involving emergency vehicles, where reliable communication is of utmost importance. In this research, we propose a supervised learning approach based on artificial neural networks (ANNs) to develop a predictive model capable of estimating the level of signal degradation, represented by the bit error rate (BER), based on the obstacles perceived by moving emergency vehicles. By establishing a relationship between the level of signal degradation and the encountered obstacles, our proposed mechanism enables efficient routing decisions to be made prior to the transmission process. Consequently, data packets are routed through paths that exhibit the lowest BER. To gather the necessary training data, we employed SUMO and NS-3 simulations. The simulation results demonstrate that our developed model successfully learns and accurately estimates the BER for new data instances. Overall, our research contributes to enhancing the performance and reliability of communication in urban VANET environments, especially in critical scenarios involving emergency vehicles, by leveraging supervised learning and artificial neural networks to predict signal degradation levels and optimize routing decisions accordingly.

As a stimulus signal, coded electrical signals can control the motion behavior of animals, which has been widely used in the field of animal robots. In current research, most of the stimulus signals used by researchers are traditional waveform, such as square waves. To enrich the stimulus waveform, a wireless animal robot stimulation system based on neuronal electrical signal characteristics is presented in this paper. The stimulator uses the CC1101 wireless module to control animal behavior through brain stimulation. The LabVIEW-based graphical user interface(GUI) can manipulate brain stimulation remotely while the stimulator powered by battery. Additionally, the spikes of animals have been simulated by this system through Direct Digital Synthesizer(DDS) algorithm. The GUI enable users to customize the combination of these analog spike signals. The recombined signals are sent to the stimulator through CC1101 as stimulus signals. In vivo experiments conducted on five pigeons verified the efficacy of the stimulation mechanism. The analog spike signal with an amplitude of 3-5V successfully caused the pigeon’s turning behavior. The feasibility of the analog spike signals as stimulus signals was successfully verified. Increased the diversity of stimulus waveform in the field of animal robots.

The paper proposes a rock classification method using the vibration signal of the rotary drilling process. This proposed method classifies four rocks with a reliability of 100 %, from the vibration signal record of a lasting 1/4 second. For the design of a suitable classification method, several attributes of the vibration signal were calculated for two different signal recording lengths. Cluster dendrogram, ANOVA test, and boxplot were used to determine useful attributes and proper signal length. The classification rule was found using a decision tree, machine learning tool. The publication gradually describes the process of creating the classification method and the results of the reliability verification of the proposed classification method. Rock disintegration by rotary drilling was carried out under standardized experimental conditions. The disintegration rocks were andesite, granite, limestone, and concrete.

Muscle spindles are encapsulated sensory organs found in most of our muscles. Prevalent models of sensorimotor control assume the role of spindles is to reliably encode limb posture and movement. Here, I argue that the traditional view of spindles is outdated. Spindle organs can be tuned by spinal γ motor neurons that receive top-down and peripheral input, including from cutaneous afferents. A new model is presented, viewing γ motor activity as an intermediate coordinate transformation that allows multimodal information to converge on spindles, creating flexible coordinate representations at the level of the peripheral nervous system. That is, I propose that spindles play a unique overarching role in the nervous system: that of a peripheral signal-processing device that flexibly facilitates sensorimotor performance, according to task characteristics. This role is compatible with previous findings and supported by recent studies with naturalistically active humans. Such studies have so far shown that spindle tuning enables the independent preparatory control of reflex muscle stiffness, the selective extraction of information during implicit motor adaptation, and for segmental stretch reflexes to operate in joint space. Incorporation of advanced signal-processing at the periphery may well prove a critical step in the evolution of sensorimotor control theories.

A case study is presented which demonstrates the value and validity of a novel approach to the use of consolidated amateur (‘ham’) radio reception reports as indicators of the presence of intense ionospheric sporadic E (Es). It is shown that the use of amateur data can provide an important supplement to other techniques, allowing the detection and tracking of Es where no suitable ionosonde or other measurements are available. The effectiveness of the approach is demonstrated by reference to ionosonde data, and the advantages and limitations of the technique are discussed.

In tele-monitoring, wireless body area networks (WBANs), sleep analysis and other applications involving electroencephalogram (EEG) signal, due to the high number of EEG recording channels, long recording time and several repetition of recordings to reach the highest signal-to-noise ratio, the amount of acquired data by the sensors is too large, demanding use of some compression procedure. Compressed sensing can be considered as one of the most effective compression methods in terms of compression ratio, which needs the underlying signal be sparse or have sparse representation in an appropriate domain. EEG signal is not sparse in time domain, therefore, in this paper correlation based weighted recursive least squares dictionary learning algorithm (CBW-RLS) is proposed that uses between-channel correlations to sparsify EEG signals. Due to the low-rank structure of EEG signals, exploiting between-channel correlations increase the sparsity level of the model while reducing the computational cost of dictionary learning procedure. This is done by merely updating the dictionary atoms which are involved in the sparse model of the previous data, reducing the total number of data used at each iteration and speeding up the dictionary learning algorithm. The simulation results show that the proposed method has better performance in terms of both quality of the EEG reconstruction and the computational cost compared to the other methods.

Machine Learning (ML) approaches have been fruitfully applied to several classification problems of neurophysiological activity. Considering the relevance of emotion in human cognition and behaviour, ML found an important application field in emotion identification based on neurophysiological activity. Nonetheless, the literature results present a high variability depending on the neuronal activity measurement, the signal features and the classifier type. The present work aims to provide new methodological insight on ML applied to emotion identification based on electrophysiological brain activity. For this reason, we recorded EEG activity while emotional stimuli, high and low arousal (auditory and visual) were provided to a group of healthy participants. Our target signal to classify was the pre-stimulus onset brain activity. Classification performance of three different classifiers (LDA, SVM and kNN) was compared using both spectral and temporal features. Furthermore, we also contrasted the classifiers performance with static and dynamic (time evolving) features. The results show a clear increased in classification accuracy with temporal dynamic features. In particular, the SVM classifiers with temporal features showed the best accuracy (63.8 %) in classifying high vs. low arousal auditory stimuli.

Transient receptor potential melastatin-8 (TRPM8) is a cation channel that is activated by cold and “cooling agents” such as menthol and icilin, which induce a cold sensation. Stimulation of TRPM8 activates an intracellular signaling cascade that ultimately leads to a change in the gene expression pattern of the cells. Here, we investigated the TRPM8-induced signaling pathway that links TRPM8 channel activation to gene transcription. Using a pharmacological approach, we show that inhibition of phosphatidylinositol 4-phosphate 5 kinase alpha (PIP5K), an enzyme essential for the biosynthesis of phosphatidylinositol 4,5-bisphosphate, attenuated TRPM8-induced gene transcription. Analyzing the link between TRPM8 and Gq proteins, we show that pharmacological inhibition of the beta gamma subunits impairs TRPM8 signaling. In addition, genetic studies showed that TRPM8 requires an activated Galpha subunit for signaling. In the nucleus, the TRPM8-induced signaling cascade triggers an activation of the transcription factor AP-1, a complex consisting of a dimer of basic region leucine zipper (bZIP) transcription factors. Here, we identified the bZIP protein c-Jun as an essential component of AP-1 within the TRPM8-induced signling cscade. In summary, with PIP5K, Gq subunits and c-Jun we have identified key molecules in the TRPM8-induced signaling from the plasma membrane to the nucleus.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

In this study dual PET and contrast enhanced MRI were combined to investigate their correlation per voxel in patients at initial diagnosis with suspected glioblastoma. Correlation with contrast enhancement (CE) as an indicator of BBB leakage was further used to evaluate whether PET signal is likely caused by BBB disruption alone, or rather attributable to specific binding after BBB passage. PET images with [18F]GE180 and the amino acid [18F]FET were acquired and normalized to healthy background (TBR). Contrast enhanced images were normalized voxel by voxel with the pre-contrast T1-weighted MRI to generate relative CE values (rCE). Voxel-wise analysis revealed a high PET signal even within the sub-volumes without detectable CE. No to moderate correlation of rCE with TBR voxel-values and a small overlap as well as a larger distance of the hotspots delineated in rCE and TBR-PET images were detected. In contrast, voxel-wise correlation between both PET modalities was strong for most patients and hotspots showed a moderate overlap and distance. The high PET signal in tumor sub-volumes without CE observed in voxel-wise analysis as well as the discordant hotspots emphasize the specificity of the PET signals and the relevance of combined differential information from dual PET and MRI images.

Characterization of flying insects in-situ measurement using remote sensing spectroscopy is an emerging research field. Also, most analysis techniques in remote sensing spectroscopy are based on the use of an intensity threshold which introduces indeterminacies in the number of detected specimens. In this manuscript, we investigated the possibility of analysing passive remote sensing spectroscopy measurement data using the maximum noise fraction method. The results obtained show that this analysis technique can help to overcome the measurement of background noise in spectroscopic measurements.

Background: Modern MEG devices include 102 sensor triplets containing one magnetometer and two planar gradiometers. The first processing step is often a signal space separation (SSS), which provides a powerful noise reduction. A question commonly raised by researchers and reviewers is which data should be employed in source reconstruction: (1) magnetometers only, (2) gradiometers only, (3) magnetometers and gradiometers together. The MEG community is currently divided about the proper answer and strong arguments in favor and against these three approaches often expressed. Methods: First, we provide theoretical evidence that both gradiometers and magnetometers contain the same information after SSS, and argue that they both result from the backprojection of the same SSS components. Then, we compare beamforming source reconstructions from magnetometers and gradiometers in real MEG recordings before and after SSS. Results: Without SSS, the correlation between source time series extracted from magnetometers and gradiometers was high, with Pearson correlation coefficient r=0.5-0.8. After SSS, these correlation values increased dramatically, reaching over 0.90 across all cortical areas. Conclusions: After SSS, almost identical source reconstructions (r>0.9) can be obtained with magnetometers and gradiometers, as long as regularization is selected appropriately to account for the different properties in magnetometers and gradiometers covariance matrices.

Schistosoma infection in snails can be monitored by microscopy or indirectly by sentinel mice. As both these approaches sometimes miss infections, more sensitive tests are needed, particularly in low-level transmission settings. In this study, the loop-mediated isothermal amplification (LAMP) technique, designed to detect a specific 28S ribosomal S. japonicum gene with high sensitivity, was compared to microscopy using snail samples from 51 areas endemic for schistosomiasis in five Chinese provinces. The results were compared with those by polymerase chain reaction (PCR) adding DNA sequencing as a reference when needed. The testing of pooled snail samples showed that a dilution factor of 1/50, i.e., one infected snail plus 49 non-infected ones, would still result in a positive reaction after the recommended number of amplification cycles. Testing a total of 232 pooled samples, emanating from 4,006 snail specimens, with the LAMP assay showed a 6.5% rate of infection, while traditional microscopy found only 0.04% positive samples in the same materials. Parallel PCR analysis confirmed the diagnostic accuracy of the LAMP assay, with DNA sequencing even giving LAMP a slight lead. Microscopy and the LAMP test were carried out at local schistosomiasis-control stations demonstrating that the potential of the latter assay to serve as a point-of-care (POC) test with results available within 60–90 minutes, while the more complicated PCR test had to be carried out at the National Institute of Parasitic Diseases (NIPD) in Shanghai, China. In conclusion, LAMP was found to be clearly superior to microscopy and as good as, or better, than PCR. Application of LAMP testing would be useful for surveillance and risk prediction as it requires less time than other techniques and can be used under field conditions, which improves and accelerates schistosomiasis control.

RF photonic transversal signal processors, which combine reconfigurable electrical digital signal processing and high-bandwidth photonic processing, provide a powerful solution for achieving adaptive high-speed information processing. Recent progress in optical microcomb technology provides compelling multi-wavelength sources with compact footprint, yielding a variety of microcomb-based RF photonic transversal signal processors implemented by either discrete or integrated components. Although operating based on the same principle, processors in these two forms exhibit distinct performance. This letter presents a comparative investigation into their performance. First, we compare the performance of state-of-the-art processors, focusing on the processing accuracy. Next, we analyze various factors that contribute to the performance differences, including tap number and imperfect response of experimental components. Finally, we discuss the potential for future improvement. These results provide a comprehensive comparison of microcomb-based RF photonic transversal signal processors implemented using discrete and integrated components and provide insights for their future development.

Vanadium is a well-known essential trace element, which usually exists in oxidation states in form of vanadate cation intracellularly. The pharmacological study of vanadium begins at the discovery of its unexpected inhibitory effect on ATPase. Thereafter, the protective effects on cells and the abilities in glucose metabolism regulation were observed from vanadium compound, leading to the application of vanadium compounds in clinical trials for curing diabetes. Alzheimer’s dis-ease (AD) is the most common dementia disease in elderly people. However, there is still no efficient agents for treating AD safely to date. This is mainly because of the complexity of the pathology, which are characterized by the senile plaques composed by amyloid-beta (Aβ) protein in the parenchyma of brain and the neurofibrillary tangles (NFTs) derived from hyperphosphorylated tau protein in neurocyte, along with mitochondrial damage, and eventually the central nervous system (CNS) atrophy. AD was also illustrated as type-3 diabetes, because of the observations of insulin deficiency and the high level of glucose in cerebrospinal fluid (CSF), as well as the im-paired insulin signaling in brain. In this review, we summarized the advance of applicating vanadium compound on AD treatment in experimental research and pointed out the limitation of the current study on using vanadium compounds in AD treatment. We hope it will help the future study in this field.

The fetal heart rate (FHR) is a screening signal for preventing fetal hypoxia during labor. When experts analyze this signal, they have to position a baseline and identify decelerations and accelerations. These steps can potentially be automated and made more objective by data processing analysis, but training and evaluation datasets are required. Here, we describe a dataset of 155 FHR recordings in which a reference baseline, accelerations and decelerations have been annotated by expert consensus. 66 FHR recordings with a shared expert analysis have been included in a training dataset, and 90 other FHR recordings with a non-shared expert analysis have been included in an evaluation dataset. Researchers wishing to evaluate their automatic analysis method should submit their results for comparison with the expert consensus. The dataset also contains the results produced by 11 re-coded automatic analysis methods from the literature. All the data are available at http://utsb.univ-catholille.fr/fhr-review.

The vibration signal of heavy gearbox presents non-stationary and nonlinear characteristics, which increases the difficulty to extract the fault feature. When the gear has a subtle fault, it may cause a perceptible change of local fluctuation rather than the large scale fluctuation. Therefore, the feature parameters extracted from local fluctuation can effectively improve the recognition performance of the gear fault. In this paper, a novel signal processing method based on variational mode decomposition (VMD) and detrended fluctuation analysis (DFA) is proposed to identify the gear fault of heavy gearbox. Firstly, the raw vibration signal is decomposed several mode components by VMD, which is an adaptive and non-recursive signal decomposition method. Next, the sensitive mode component is selected by a maximal indicator, which is composed of kurtosis and correlation coefficient of relative higher frequency mode components corresponding to local fluctuation of raw vibration signal. Finally, the characteristics of the double-scales feature parameters of selected sensitive mode are extracted by DFA. In addition, the position of turning point of double scales is estimated by sliding windowing algorithm. The proposed method is evaluated through its application to gear fault classification using vibration signal. The results demonstrates that the recognization rate of gear faults condition have marked improvement by proposed method than the DFA of Small Time Scale (STS-DFA) method.

In metastatic pancreatic cancer patients non eligible to surgery, signal-targeted therapies so far failed to show a significant amelioration of survival. These therapeutic options were tested in Phase II/III clinical trials mostly in combination with the reference treatment Gemcitabine. These innovative therapies aim at annihilating the oncogene dependency; they also aim at renormalizing the tumoral stroma to allow immune cell function or re-vascularisation. Transcriptomics and genomics large scale analysis show the great heterogeneity of pancreatic cancers and failed to clearly delineate specific oncogene dependency besides oncogenic Kras. In this review, we will describe the most recent proteomic data in pancreatic tumors and its metastasis, which could help at identifying their major signalling dependencies, as well as explain why they are intrinsically resistant to signal-targeted therapies. We will also discuss why PI3K signalling, as a paradigm of pro-tumorigenic cell signalling and of tumoral adaptative resistance to drugs, is a relevant target in this context.

In metastatic pancreatic cancer patients non eligible to surgery, signal-targeted therapies so far failed to show a significant amelioration of survival. These therapeutic options were tested in Phase II/III clinical trials mostly in combination with the reference treatment Gemcitabine. These innovative therapies aim at annihilating the oncogene dependency; they also aim at renormalizing the tumoral stroma to allow immune cell function or re-vascularisation. Transcriptomics and genomics large scale analysis show the great heterogeneity of pancreatic cancers and failed to clearly delineate specific oncogene dependency besides oncogenic Kras. In this review, we will describe the most recent proteomic data in pancreatic tumors and its metastasis, which could help at identifying their major signalling dependencies, as well as explain why they are intrinsically resistant to signal-targeted therapies. We will also discuss why PI3K signalling, as a paradigm of pro-tumorigenic cell signalling and of tumoral adaptative resistance to drugs, is a relevant target in this context.

As screen sizes are becoming larger and larger, which are beyond human’s physical limitation for direct touching interaction, remote controls are inevitable. However, as techniques applied so far, inertial gyroscopes are susceptible to position inaccuracies, and gesture recognition is limited by cameras’ focus depth and viewing angle. Grating antenna light trapping technology will be an ideal candidate providing the ghost point problem for multipoint inputs can be solved. Therefore, we propose a differential amplitude modulation scheme for grating antenna based multi beam optical touch, which can recognize different incidence points. Where, the amplitude of the incident beams was coded with different pulse width at first. Then, after been trapped by the grating antenna and been transferred into currents by the lined detector arrays, the incident points of the individual beams were recognized and differentiated. The scheme was successfully verified on an 18-inch screen, where two-point optical touch with position accuracy error under 3mm and response time less than 7ms under modulation frequency of 10kHz on both incident beams are obtained. This work paves a practical way for remote multi-point touch, which can make digital mouse in consistent to the users pointing direction obeying natural three-point one ling aiming rule instantaneously.