To achieve a narrow bandwidth optical filter with a wide swept range for new generation optical spectrum analysis (OSA), an optoelectronic equivalent narrowband filter (OENF) is investigated and a swept optical filter with bandwidth of several MHz and swept range of several ten nanometers is built using electric filters and a swept laser as local oscillator (LO). The principle of OENF is introduced and analysis of OENF system is presented. Two electric filters are optimized to be RBW filters for high and medium spectral resolution application. Both simulations and experiments are conducted to verify OENF principle and results show that power uncertainty is less than 1.2% and spectral resolution can reach 6 MHz. Then, a real-time wavelength calibration system consisting of HCN gas cell and FP etalon is proposed to guarantee a wavelength accuracy of ±0.4 pm at C-band and to reduce the influence of phase noise and nonlinear velocity of swept LO. Finally, experiments on OSA of actual spectra of various optical sensors using OENF system are conducted. Experimental results indicate that OENF system has an excellent capacity in analysis of fine spectrum structures.

The aim of this study was to examine the oxidation of human serum albumin (HSA) caused by oxidative stress after an exhaustive exercise such as ultra-marathon race. Thus, blood samples from 12 adult runners who underwent a 103 km mountain ultra-marathon race were collected pre- and 24, 48 and 72 h post race. HSA was partially purified using affinity chromatography and then was subjected to Western blot analysis for disulfide dimers determination, indicating oxidation. The results were correlated with those from a previous study in which the same samples were analyzed using different oxidative stress markers and a good correlation with protein carbonyls (PC) at all time points was observed. Moreover there was a significant correlation with static oxidation-reduction potential (sORP) at 24 h, and a negative correlation with capacity oxidation-reduction potential (cORP) at 24 and 48 h. In addition, an individual analysis of albumin dimers exhibited great inter-individual differences. This inter-individual variability in the oxidation of HSA may suggest different interventions (e.g. through diet) in order to confront the effects on athletes’ organism after a strenuous exercise. In conclusion, this study supported the importance of the assessment of albumin dimers as a predictive marker for exercise-induced oxidative stress.

The aim of this study is to solve the problems of complicated pretreatment and high analytical cost in the detection technology of trace drug toxicants in municipal wastewater. A high-performance magnetic sorbent was synthesized for enrichment of trace drug substances in wastewater to develop magnetic solid-phase extraction pretreatment combined with the acoustic ejection mass spectrometry (AEMS) analytical methods for the molecules in wastewater drug toxicants. The magnetic nanospheres was successfully prepared by magnetic nanoparticles modified with divinylbenzene and vinyl pyrrolidone.The results showed that the linear dynamic range of 17 drugs was 1-500 ng/L, the recovery was 43%-105%, the matrix effect was more than 67%, the limit of quantitative detection was 1-2 ng/L, and the detection time of each sample was 2.98s. It can be seen that the developed magnetic solid-phase extraction (MSPE) method is a good solution to the problem of complicated pre-treatment and analytical cost in the detection of drugs in wastewater. The developed magnetic material and acoustic excitation coupled mass spectrometry analysis method can realize the low-cost, efficient enrichment and fast analysis of different kinds of drug molecules in urban sewage.

Landiolol is an ultra-short-acting, selective ß1- adrenergic receptor blocker that was originally approved by Japan for the treatment of intraoperative tachyarrhythmias. It has gained attention for its use in the management of tachyarrhythmias and perioperative tachycardia, especially atrial fibrillation for both cardiac and non-cardiac surgeries. It can be the ideal agent for heart rate control due to its high β1‐selectivity, the potent negative chronotropic effect, a limited negative inotropic potential, and an ultrashort elimination half‐life (around 4 min); moreover, it may have a potential therapeutic effect for sepsis and pediatric patients. Landiolol seems to be superior to other short‐acting and selective beta‐blockers such as esmolol. This review aims to provide a comprehensive overview of landiolol, a new ultra-short-acting ß1 selective antagonist, including its pharmacology, clinical applications, efficacy, safety profile, and future directions in research and clinical data.

Polyphenols are the most common organic compounds in wine. They improve both the sensory aspects of wine and human health by activating antioxidant systems. Therefore, there is a great need for a simple, fast and accessible method to determine the polyphenol content of wine. The aim of this study is to characterize polyphenolic compounds in natural wine samples using an electrochemical method and a modified carbon paste electrode with TiO2 nanoparticles. This work is motivated by the promising improvement of the sensing properties of a TiO2 nanoparticle-modified carbon paste electrode observed in the electrooxidation of different polyphenols. Since the voltammetric response of wine is largely irreversible, another motivation was the possibility of improving the processing of voltammograms to obtain data indicative of wine polyphenols, based on the approach described in the seminal work by Espinoza et al. The modified electrode studied provides an improved and reproducible voltammetric response of gallic acid in wine samples and provides a good basis for further development of an integrated sensor/data system with the possibility of wider application for the quantification of gallic acid as a flavor and visually relevant parameter in winemaking.

This paper gives an overview of the large-scale tectonic styles encountered in orogens worldwide. Thin-skinned and thick-skinned tectonics represent two end member styles recognized in mountain ranges. Both styles are encountered in former passive margins of continental plates. Thick-skinned style including the entire crust and possibly the lithospheric mantle are associated with intracontinental contraction. Delamination of subducting continental crust and horizontal protrusion of upper plate crust into the opening gap occurs in the terminal stage of continent-continent collision. Continental crust thinned prior to contraction is likely to develop relatively thin thrust sheets of crystalline basement. A true thin-skinned type requires a detachment layer of sufficient thickness. Thickness of the décollement layer as well as the mechanical contrast between décollement layer and detached cover control the style of folding and thrusting within the detached cover units. In subduction-related orogens, thin- and thick-skinned deformation may occur several hundreds of kilometers from the plate contact zone. Basin inversion resulting from horizontal contraction may lead to the formation of basement uplifts by the combined reactivation of pre-existing normal faults and initiation of new reverse faults. In most orogens thick-skinned and thin-skinned structures both occur and evolve with a pattern where nappe stacking propagates outward and downward

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

In past years, lithium-ion batteries (LIBs) can be found in every aspect of life, and batteries, as energy storage systems (ESSs), need to offer electric vehicles (EVs) more competition to be accepted in markets for automobiles. Thick electrode design could reduce the use of non-active materials in batteries that its energy density would be improved and its cost would be cut. However, thick electrodes are limited by their weak mechanical stability and poor electrochemical performance, these limitations could be classified as the critical cracking thickness (CCT) and the limited penetration depth (LPD). The understanding of the CCT and the LPD have been proposed and the recent works on breaking the CCT and improving the LPD are listed in this article. By comprising these attempts, some thick electrodes could not offer higher mass loading or higher accessible areal capacity that would defeat the purpose.

From the theory of relativistic chemical kinetics [M. W. Baig, Int. J. Mod. Phys. B 31, 1750177 (2017)] relativistic thermodynamics and kinetics for electrode processes have been developed to explain time dilation for electrode processes. For a moving observer moving at fractions of the speed of light, cell potential is observed to decrease. This results in the slower oxidation and reduction of ions at the respective electrodes. The newly formulated Lorentz transformation of the electrode and cell potential is explained in terms of generation of spin 2-boson “gravitons” from fusion of spin-1 boson “virtual-photons” mediating electrostatic force of attraction between ions and electrodes. It is postulated that birth of spin 2-boson i.e. gravitons is followed by their eventual escape in any of higher 4+n dimensions. To demonstrate the effectiveness of the present theory, the Daniel cell is considered as a numerical example.

The thick functionally graded material (FGM) circular cylindrical shells with advanced varied shear correction coefficient and third-order shear deformation theory (TSDT) under advanced thermal vibration are studied by the method of generalized differential quadrature (GDQ). The coefficient of displacement model of TSDT is applied to derive the equations of motion for the thick FGM circular cylindrical shells. The stiffness in simpler forms of thick FGM circular cylindrical shells and temperature rise in linear expression of the heat conduction equation are used. The differential equations in dynamic equilibrium state of thick FGM circular cylindrical shells can be obtained and rewritten into displacements and shear rotations in partial derivative expressions under dynamic thermal loads in partial derivative expressions. Parametric effect studies including advanced nonlinear varied shear correction coefficient, nonlinear coefficient c1 value, power law index and thermal temperature difference of external heating loads on the displacements and stresses of thick FGM cylindrical shells under thermal dynamic vibration are investigated.

Low temperature cofired ceramics (LTCC) have conquered a niche segment in biological microelectromechanical systems (BioMEMS) during the last two decades. Since 3-dimensional assembly and rapid prototyping capability are outstanding features of the technology, bioreactors with complex geometry can easily be produced. Particularly needed functions are working electrodes, e.g. for impedance measurements and reference electrodes consisting in platinum or silver-silver chloride. Although the distinct grainy surface of thick film materials influences the double layer properties, data describing the bioelectronic interface and biocompatibility of common thick film materials are rarely published up to now. This works aims to fill this gap by studying the surface properties, composition, electrochemical properties and biocompatibility of commercially available thick film materials. It was found that thick film gold is suitable as electrode material in direct cell contact since an appropriate proliferation of the cell culture was observed. Poly(3,4-ethylenedioxythiophene) coating decreases the absolute value of the zeta potential of thick film gold from 16.55 V to 11.78 mV without any change in vitality of the cells. Thick film platinum layers have a porous structure entailing an enlargement of the effective surface by a factor of 21.6 and can be used as reference instead of silver/silver chloride, which was identified to be incompatible with cell culture. The investigations show that some commercially available cost-effective thick film materials are compatible with cell culture and the here presented data give an orientation for the use of the same in LTCC bioreactors.

In this paper any superalgebra is generalized to a new form, namely ultra algebra. We study some algebraic structure results for ultra algebras and we have defined some maps on ultra algebras to know ultra derivation and Jordan ultra derivation. Moreover on certain assumptions we have proved that Jordan ultra derivation is an ultra derivation.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Along with the rapid development of technology and industry, the need for energy storage has become fundamental. One promising energy storage devices is the supercapacitor. Several type supercapacitors are available, one of which is the electrical double-layer capacitor made from carbon graphite and multiwalled carbon nanotubes (MWCNTs). In this study, we combined these two materials into a working electrode in a three-electrode system. In the morphological analysis using scanning electron microscope, transmission electron microscope, and X-ray diffraction, the two materials were found to have formed a composite on the surface. In the electrochemical analysis, two types of testing were conducted using cyclic voltammetry and electrochemical impedance spectroscopy. Electrochemical analysis was carried out on five electrolyte concentrations of Na2SO4 from 1 to 6 M. The capacitance produced at concentrations of 1, 2, 3, 4, and 5 M were 34.395, 35.808, 46.284, 49.502, and 76.815 F/g, respectively. At an electrolyte concentration of 5 M Na2SO4, an energy density of 27.312 Wh/Kg and a power density of 343.786 W/Kg were produced. Meanwhile on concentration of 6 M, the surface of the electrode was damaged.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

In this work, we demonstrate that cutting diamond crystals with a laser (532 nm wavelength, 0.5 mJ energy, 200 ns pulse duration at 15 kHz) produces a ≲20nm thick surface layer with magnetic order at room temperature. We have measured the magnetic moment with a SQUID magnetometer of six natural and six CVD diamond crystals of different size, nitrogen content and surface orientations. A robust ferromagnetic response at 300 K is observed only for crystals that were cut with the laser along the (100) surface orientation. The magnetic signals are much weaker for the (110) and negligible for the (111) orientations. We attribute the magnetic order to the disordered graphite layer produced by the laser at the diamond surface. The ferromagnetic signal vanished after chemical etching or after moderate temperature annealing. The obtained results indicate that laser treatment of diamond may pave the way to create ferromagnetic spots at its surface.

Electronic designers nowadays are facing two challenging demands for various applications: miniaturization and increased functionality. To satisfy these seemingly opposed requirements, reducing the number of mounted components—and thus solder joints—in PCB designs becomes an attractive approach by directly printing passive components such as embedded resistors into the circuit. This approach can also potentially increase the reliability, such as “mean time between failures” (MTBF), while reducing the circuit board size. With its unique capabilities for non-contact precision material deposition, the Aerosol Jet® direct-write technology has been enabling additive manufacturing of fine-feature electronics conformally onto flexible substrates of complicated shapes. The CAD/CAM controlled relative motions between substrate and print head allows convenient adjustment of the pattern and pile height of deposited material at a given ink volumetric deposition rate. To date in the printed electronics industry, additively printing embedded polymer-thick-film (PTF) resistors has mostly been done with screen printing using carbon-based paste inks. Here we demonstrate results of Aerosol Jet® printed PTF resistors of resistance values ranging from ~50 W to > 1 kW, adjustable (among several variable parameters) by the number of stacked layers (or print passes with each pass depositing a fixed amount of ink) between contact pads of around 1 mm apart with footprint line typically < 0.3 mm. In principle, any ink material that can be atomized into fine droplets of 1 to 5 microns can be printed with the Aerosol Jet® system. However, the print quality such as line edge cleanliness can significantly influenced by ink rheology which involves solvent volatility, solids loading, and so on. Our atomizable carbon ink was made by simply diluting a screen printing paste with a compatible solvent of reasonable volatility, which can be cured at temperatures below 200 ^oC. We show that Aerosol Jet® printed overlapping lines can be stacked to large pile height (to reduce the resistance value) without significant increase of line width, which enables fabricating embedded resistors with adjustable resistance values in a limited footprint space.

Fire behavior of natural rubber latex foam under different thickness conditions(d=1,2and 5cm)were explored though a little of experiments by using the self-built small scale experimental platform. It can be shown that the flame spread law of thermally thin and thermally thickness are different. Natural rubber latex foam with thickness of 2cm show higher fire risk, which value of flame spread rate, maximum flame height, maximum mass loss rate and maximum temperature is 0.00293m/s, 851.875mm, 1.83g/s, 948K,repectively.That may because the thickness of residue formed of thermally thick materials is larger than the thin one, obstructing the contact of the natural rubber latex foam with fresh air .In addition, a special phenomenon is noticed that during the second stage, the bottom unburned zone located in the four edges(thermally thin material) and middle player(thermally thick material).

Electrode degradation in continuous resistance spot welding process of BH 220 steel was evaluated by electrode life test, and weldability tests were conducted by geometry features measurement, mechanical property analysis, and electrode diameter measurement with 88 or 176 weld intervals. The analysis of weld geometry shows that the HAZ width, nugget diameter, and nugget area tend to decrease rapidly, while the nugget height tends to firstly increase with the weld repetitions till the welding heat input becomes too small to form the valid nugget. The peak load shows a rapid downward trend, while failure energy and maximum displacement slightly increase till the 176th weld and then decrease. The cavities and pores in the nugget mainly appear after the 176th spot weld. The electrode diameter increases during welding. The reason for the increase in electrode diameter may be that the contact area between the electrode and BH 220 steel sheets becomes smaller in the welding process, which causes the continuous sticking phenomenon between the electrode and the BH 220 steel sheets. In the absence of alloying, the edge of the electrode is geometrically deformed, while Cu-Zn-Fe alloying occurs in the area in contact with the BH 220 steel sheet.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Electrochemical energy conversion and storage is key for the use of regenerative energies at large scale. A thorough understanding of the individual components, such as the ion conducting membrane and the electrode layers, can be obtained with scattering techniques on atomit to molecular length scales. The largely heterogeneous electrode layers of High-Temperature Polymer Electrolyte Fuel Cells are studied in this work with small- and wide-angle neutron scattering at the same time with the iMATERIA diffractometer at the spallation neutron source at J-PARC, opening a view on structural properties on atomic to mesoscopic length scales.

The experimental verification for the computational method sometimes varies due to numerous factors such as the manufacturing process and the materials' property change due to environmental aspects. In this work, we performed verification of experimental and computational evaluation of a hybrid composite moderate thick plate. The experiment was performed with simplistic approaches and without the advanced tools of preparing composite materials. This is due to the fact that most of the students in many developing countries around the world cannot have access to such equipment. As such, in this research, we are presenting cheap and easy preparation methods, with some details, for even equipment calibration and some tricks to attain a reliable composite structure for educational purposes. Moreover, the software and solvers used in this study are freely provided by the supplier for educational purposes. This study examined two methods for producing carbon and glass/polyester composite plates and discussed which one was best based on mechanical properties for different volume fractions, random stacking sequences, and ply angles (using OCTAVE's random estimation program). It also determined the three natural frequencies experimentally and with the aid of ANSYS. Less than 6% separated the experimentally determined natural frequencies from the calculated results.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

The novelty of this study consists in: i) synthesis and characterization of electrode materials recycled from a spent car battery and doped with MnO2 and CuO by the analysis of X-ray diffraction (XRD), Infrared (IR) and Electron Paramagnetic Resonance (EPR) data and ii) the investigation of electrochemical properties of prepared materials in view of new applications as electrode materials for battery. Electron Paramagnetic Resonance (EPR) data indicate that the intensity of the resonance line corresponding to the Cu+2 ion was modified with the increase of the dopant content. The analysis of X-ray Absorption Spectroscopy (XAS) data indicates that by increasing the dopant content there is a process of ordering the oxygen atoms around the lead similar to the PbO2 theoretical model. The electrochemical performances of the recycled and manganese-copper-doped materials are optimized for applications as new anodic electrode for the car battery.

The welding and construction processes of H-type thick-plate-bridge steel involve complex multi-pass welding processes, which is difficulty to ensure its welding performance. Accordingly, it is crucial to explore the inherent correlation among the welding processes parameters and welding quality, and applied it into the welding robots, eliminating the instability from manual welding. In order to improve the welding quality, the GMAW (Gas Metal Arc Welding) welding process parameters are simulated using the Q345qD bridge steel flat joint model. Four welds with X-shaped grooves are designed to optimize the parameters of welding current, welding voltage, and welding speed. The optimal welding process parameters are investigated through thermal-elastic-plastic simulation analysis and experimental verification. The results indicate that when the welding current is set to 230A, the welding voltage to 32V, and the welding speed to 0.003m/s, the maximum deformation of the welded plate is 0.52mm, with a maximum welding residual stress of 345MPa. Both the simulation results of multi-pass welding and experimental tests meet the welding requirements, as they show no excessive stress or strain. These parameters can be applied into building large steel frame bridges with welding robots, improving the quality of welded joints.

The kinetics and efficacy profiles of photoinitiated polymerization are theoretically presented. For the same dose, lower light intensity achieves a higher steady-state-efficacy (SSE) in type-I; in contrast, type-II has an equal SSE. Higher light intensity has a faster rising efficacy, due to faster depletion of photoinitiator (PS) concentration. However, type-II process is also affected by the available oxygen. Higher light intensity produces more efficient singlet oxygen, resulting a higher transient efficacy, in which all intensities reach the same SSE when oxygen is completely depleted. With external oxygen, type-II efficacy increases with time, otherwise, it is governed only by the light dose, i.e., same dose achieves same efficacy. Moreover, type-II has an efficacy follows Bunsen Roscoe law (BRL), whereas type-I follows non-BRL. The measured type-I efficacy and gelation profile are analyzed by our analytic formulas. Schematics of the photocrosslinking stage defined by the availability of oxygen is developed, where both type-I and –II coexist until the oxygen is depleted. The overall efficacy may be enhanced by resupply of PS or oxygen during the light exposure. The roles of light dose and PS concentration on the efficacy of photoinitiated polymerization should be are governed a new concept of a volume efficacy (Ve), defined by the product of the crosslink (or gelation) depth (CD) and local [efficacy].

Optical materials with a tunable localized surface plasmon resonance (LSPR) are of a great interest for applications in photonics and optoelectronics. In the present study we explored the potential of generating the LSPR band with an ultra-broad range of over 1000 nm in gold nanoparticles (NPs) precipitated through the thermal treatment in ZnO-Al2O3-SiO2 glass. Using the optical absorption spectroscopy, we demonstrated that the LSPR band's position and shape can be finely controlled by varying the thermal treatment route. Comprehensive methods including Raman spectroscopy, X-ray diffraction and high-resolution transmission electron microscopy were used to study the glass structure, while computational approaches were used for the theoretical description of the absorption spectra. Obtained results allowed us to suggest a scenario responsible for such abnormal LSPR band broadening which includes possible interparticle plasmonic coupling effect taking place during the liquid-liquid phase separation of the heat-treated glass. The formation of gold NPs with an ultra-broad LSPR band in glasses holds promise for sensitizing rare earth ion luminescence for new photonics devices.

Amorphous silicon (α-Si) film present an inexpensive and promising material for optoelectronic and nanophotonic applications. Its basic optical and optoelectronic properties are known to be improved via phase transition from amorphous to polycrystalline phase. Infrared femtosecond laser radiation can be considered as a promising nondestructive and facile way to drive uniform in-depth and lateral crystallization of α-Si films that are typically opaque in UV-visible spectral range. However, so far only a few studies reported on utilization of near-IR radiation for laser-induced crystallization of α-Si providing no information regarding optical properties of the resultant polycrystalline Si films. The present work demonstrates efficient and gentle single-pass crystallization of α-Si films induced by their direct irradiation with near-IR femtosecond laser pulses coming at sub-MHz repetition rate. Comprehensive analysis of morphology and composition of laser-annealed films by atomic-force microscopy, optical, micro-Raman and energy-dispersive X-ray spectroscopy, as well as numerical modeling of optical spectra, confirmed efficient crystallization of α-Si and high-quality of the obtained films. Moreover, we highlight localized laser-driven crystallization of α-Si as a promising way for optical information encryption, anti-counterfeiting and fabrication of micro-optical elements.

Ultra-wideband wavelength division multiplexed networks enable operators to use more effectively the bandwidth offered by a single fiber pair and thus make significant savings, both in operational and capital expenditures. The main objective of this study is to minimize optical node resources, such as transponders, multiplexers and wavelength selective switches, needed to provide and maintain high quality of network services, in ultra-wideband wavelength division multiplexed networks, at low cost. A model based on integer programming is proposed, which includes a detailed description of optical network nodal resources. The developed optimization tools are used to study the ultra-wideband wavelength division multiplexed network performance when compared with the traditional C-band wavelength division multiplexed networks. The analysis is carried out for realistic networks of different dimensions and traffic demand sets.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

A new sulbatamol sulphate SBS membrane electrode was prepared that utilizing for its determination ; depend on the forming of the association complex ion of sulbatamol sulphate by the phosphotungstate counter anion deposed in poly vinyl chloride PVC polymer, by use a (Di-n- Octyl Phenyl Phthalate)(Dopp) as the plastizier substance, in membrane.The features properties as well as the behavior of it .The new electrode have been elaborated. The concentrations of medicine by utillizing This sensor show a fast, stable, near-Nernstian response in the range (1x10^-1-1x10^-6) mol/ L were determined with correlation coefficient of about (r = 0.9991) and with of a relative standard about 0.416 additionally deviation relative standard error of 1.710 %.^pot The nernast linearity slop was founded and it is equal to 28.9 mV/decade and the detection limit was 4.1 x 10^-6 mol/ L.The electrode selectivity coefficient K_i,j was calculated, in the existence of several interferences cations with confirmed medicine solutions. It was found the pH range response is in the range of (3 -7), with the response time of (30 – 116) sec. for various concentrations at room temperture , the lifetime for electrode was found to be more than 21 days. The electrode was successfully used for potentiometric limitation of sulbatamol sulphate in several pharmaceutical drugs by using direct potentiometry.

Molybdenum oxides is well-known electro-catalysts in fuel cells systems, they are usually used as anodic materials for the oxidation of low molecular weight alcohols. The utilization of Mo as catalysts in the pharmaceutical analysis is not common yet. In this study, bare glassy carbon electrodes were modified by the oxides by means of electrochemical deposition and the modified electrodes were used as catalysts for the electrochemical oxidation of hydrochlorothiazide (HCT). Well-resolved anodic peaks were reported for the analyzed pharmaceuticals when the Mo/GCE was utilized for the analysis of HCT. Analytical performance of the modified electrodes was evaluated based on the following statistical parameters; linearity ranges, correlation coefficients, limits of detection and quantitation, and recovery values. The prepared electrodes were used for the determination of the active ingredients in their pharmaceutical formulations and the reported activity was correlated to influence of the utilized pH on both structures of the used electrodes and the detected analytes.

The flow around thick airfoils at low Reynolds numbers and the possibility of using energy methods to control flowfield, increase lift and reduce drag are considered. For calculations, a series of propulsion airfoils is used, obtained by a combination of solving the inverse problem of aerodynamics and stochastic methods of global optimization. The calculations take into account the transition from the laminar flow regime to the turbulent one, which has a significant effect on the lift and airfoil drag. The applicability of various turbulence models for airfoil modelling at low Reynolds numbers is discussed. The results of numerical simulation make it possible to determine the dependence of the lift coefficient on the angle of attack and the optimal flow rate of air taken from the airfoil surface for each angle of attack. The results of numerical simulation are compared with the data of a physical experiment, and conclusions are drawn about the accuracy of various turbulence models.

The main objective of the paper is to investigate the wave propagation behaviour in composites using numerical and experimental methods. Specifically, the study focuses on the actuation of waves by two PZT transducers placed on the surface and embedded at different positions within the composites, namely the quarter and middle positions. The numerical analysis provides simulated results, while the experimental analysis involves practical testing. The paper demonstrates that the numerical results are consistent with the experimental findings. It is observed that when the PZT transducers are placed at deeper positions within the composites, the peak amplitude of the first wave packet for the A0 mode decreases. Overall, the paper contributes to the understanding of wave propagation in composites by comparing the effects of different positions of PZT transducers, both on the surface and embedded within the material. The findings highlight the influence of transducer placement on wave characteristics, particularly the reduction in peak amplitude with deeper transducer positioning.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

Recently, the difficulties in recycling and environmental pollution caused by metal-based electrode materials have limited the further development of batteries. Therefore, biomass carbon materials, with their environmental friendliness and stable performance, are the key to solving this problem. Many advances have been achieved by researchers for the application of biomass porous carbon materials in batteries. Nevertheless, the same biomass carbon materials in batteries face problems such as low utilization, low yield, and a cumbersome preparation process. This paper thus aims to summarize the recent progress of biomass carbon materials in the field of batteries and provide a detailed description of the battery performance of biomass carbon materials from three perspectives: synthesis, structure and application of carbon materials. We believe that biomass carbon composites are in line with future development and have a broad application prospect. Finally, we will give our in-depth prospect on developing biomass carbon materials.

The straightness error of guideway is one of the key indicators of ultra-precision machine, which plays an important role in the machining accuracy of work-piece. In order to measure straightness error of long distance ultra-precision guideway accurately, a splicing measurement for straightness error of guideway using high-precision flat mirror and displacement sensor was proposed in this paper, and the data splicing processing algorithm based on coordinate transformation was studied. Then comparative experiments on splicing measurement and direct measurement of straightness error were carried out on a hydrostatic guideway grinder. The maximum difference between the two measurements was about 0.3μm, which was far less than the straightness error of 5.8μm. The experiment demonstrated the correctness of the proposed splicing measurement method and data processing algorithm. To suppress the influence of straightness error on machining accuracy, a straightness error compensation algorithm based on error rotation transformation and vertical axis position correction was proposed, and the grinding experiment of a plane optics with size of 1400mm×500mm was carried out, whose flatness error after grinding was about 2.98μm. The straightness error of the grinding machine had been well suppressed.

Drying grains in a fixed bed can be an interesting alternative to prevent undesirable breaks and fractures of solids due to mechanical shocks, something that cannot be avoided when drying in moving beds. A disadvantage of fixed bed drying is that there can be significant gradients in the critical variables if the layer of particulate solids is thick. This work shows that periodically changing the direction of drying air flow is an effective technique to reduce differences within the bed and allow better uniformity of the product. Drying in a thick layer of 10 cm of sorghum grains was carried out at 50 and 60oC for air flow velocity of 2.1 m.s-1. The results showed that despite increasing the total drying time, the technique actually allowed a significant decrease in the temperature gradients and moisture content of the sorghum grains. The change in direction of the air flow caused the drying front to be displaced, sometimes towards the top, sometimes towards the base of the bed. At 50oC, drying lasted a total of 240 min, bringing the sorghum grains to an average overall moisture content of 0.13 on a dry basis.

Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Successful geophysical exploration works in Gucheng-Yaxi area located in Gaochun District, Jiangsu province, China, have been limited partly due to complex geological condition of the area and high artificial noise in data acquired using electrical and electromagnetic methods. In this work, we deployed the new anti-interference spread spectrum induced polarization method (SSIP) and audio magnetotellurics (AMT) method to detect a copper-polymetallic deposit in the area. Two-dimensional (2D) inversion results at Gucheng-Yaxi Area revealed a high chargeability anomalous zone on SSIP profile that coincided with a zone of moderate resistivity located between two resistor bodies on AMT profile. A follow up 1200 meters drill hole was established at this high chargeability-moderate resistivity zone which encountered polymetallic (copper, lead, zinc, gold and silver) mineralization at the depth ≥ 400 m. Drill hole data analysis showed that mineralization occurs interspaced in marble rock mass at varies depth. Furthermore, several low resistivity-weak chargeability sections were revealed and inferred attributed to Cretaceous sediments and faults. These faults are thought to have played critical role in the polymetallic mineralization genesis. In summary, this work demonstrated the successful of application of SSIP and AMT at detecting a metallic deposit in an area with high artificial noise. Hence the geophysical prospection potential of Gucheng-Yaxi area is great.

Electrophysiological mapping (EM) using acute electrode probes is a common procedure performed during functional neurosurgery. Due to their constructive specificities, the EM probes are lagging in innovative enhancements. This work addressed complementing a clinically employed EM probe with carbonic and circumferentially segmented macrocontacts that are operable both for neurophysiological sensing ("recording") of local field potentials (LFP), and for test stimulation. The paper illustrates in-depth the development, that is based on direct writing of functional materials. The unconventional fabrication processes were optimized on planar geometry and then transferred to the cylindrically thin probe body. We report and discuss on the constructive concept and architecture of the probe, characteristics of the electrochemical interface deduced from voltammetry and chronopotentiometry, and the results of in vitro and in vivo recording and pulse stimulation tests. Two and three directional macrocontacts were added on probes having shanks of 550 and 770 m diameters and 10-23 cm lengths. The graphitic material presents a ~2.7 V-wide, almost symmetric water electrolysis window, and an ultra-capacitive charge transfer. When tested with 150 s biphasic current pulses, the interfacial polarization stayed safely away from the water window for pulse amplitudes up to 9 mA (135 C/cm2). The in vivo experiments on adult rat models confirmed the high-quality sensing of LFPs. Additionally, the in vivo-prevailing increase of the electrode impedance and overpotential are discussed and modeled by an ionic mobility-reducing spongiform structure; this restricted diffusion model gives new applicative insight into the in vivo-uprisen stimulation overpotential.

One of the significant challenges today in the brain-machine interface using invasive methods is the stability of the chronic record. In recent years, polymer-based electrodes have gained notoriety for achieving mechanical strength values close to that of brain tissue, promoting a lower immune response to the implant. In this work, we fabricated fully polymeric electrodes based on PEDOT:PSS for neural recording in Wistar rats. We characterized the electrical properties and both in-vitro and in-vivo functionality of the electrodes. Also, we employed histological processing and microscopical visualization to evaluate tecidual immune response in 7, 14, and 21 days post-implant days. Electrodes with 400-micrometer channels showed a 12dB signal-to-noise ratio. Local field potentials were characterized under two conditions: anesthetized and free-moving. There was a proliferation of microglia to the tissue-electrode interface in the first days, with a decrease after 14 days. Astrocytes also migrated to the interface, but there was no continuous recruitment of these cells in the tissue, showing inflammatory stability at 21 days. The signal was not affected by this inflammatory action, demonstrating that fully polymeric electrodes can be an alternative to prolong the valuable time of neural recordings.

In this study the processes taking place on the surfaces of nanostructurized Cu/CuO and Cu/CuO/Pd electrodes at different potential, $E$, values in the solutions of 0.1 M KOH in H$_2$O and D$_2$O (heavy water) were probed by the surface enhanced Raman spectroscopy (SERS) and analysis of electrochemical reactions occurring under experimental conditions is presented. Bands of the SERS spectra of Cu/CuO/Pd electrode observed in the range of $E$ values from +0.3~V to 0 V~(SHE) at 1328 - 1569~cm$^{-1}$ are consistent with the existence of species which are adsorbed or weakly bound to the surface with the energy of interaction close to 15 - 21~kJ mol$^{-1}$. These bands can be attributed to the ad(ab)sorbed (H$_3$O$^+$)$\rm{_{ad}}$, (H$_2^+$)$\rm{_{ab}}$ and (H$_2^+$)$\rm{_{ad}}$ ions as intermediates in reversible HER/HOR processes taking place on Cu/CuO/Pd electrode. There was no isotopic effect observed; this is consistent with a dipole nature of electron-ion pair formation of adsorbed (H$_3$O$^+$)$\rm{_{ad}}$ and (H$_2^+$)$\rm{_{ad}}$ or (D$_3$O$^+$)$\rm{_{ad}}$ and (D$_2^+$)$\rm{_{ad}}$. In accordance with literature data SERS bands at 125-146~cm$^{-1}$ and $\sim 520-565$~cm$^{-1}$ were assigned to Cu(I) and Cu(II) oxygen species. These findings corroborate the mechanism of cascading reduction of water.

This review provides informations and details for the fabrication of biosensors that are composed from lipid membranes and have been utilized and applied to rapidly detect food toxic compounds, environmental pollutants and analytes of clinical interest. Biosensors based on polymeric lipid membranes have been used to rapidly detect a wide range of these analytes and offer several advantages such as fast response, high sensitivity and selectivity, can be portable for in the field applications, and small size. A description of the construction of these devices and their applications for the rapid detection of food toxic substance, environmental pollutants and analytes of clinical interest is provided in this review.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a Ultra-high performance concrete (UHPC) has gained worldwide popularity because of its notable mechanical response. This research studied the compressive strength, modulus of elasticity, and flexural tensile strength of UHPC. Batches were made with the addition of steel and PVA fibers using a standard procedure defined in the research. The experimental data from the compressive strength test was analyzed in the Statistica 10 software to investigate the fibers' influence on UHPC's mechanical properties. An analysis of the elastic modulus prediction was carried out according to international standards. It was found that the normalized equations for the elastic modulus are not adequate for its estimation. The statistical analysis indicated that the range of fiber quantities analyzed did not significantly affect the compressive strength and the elastic modulus. Regarding the optimized mix, its flexural tensile strength indicates that the fiber content must be higher for UHPC to be suitable for structural use.

New multilayer 3D nanocomposite wear-resistant ion-plasma hard and superhard coatings Avinit [(TiN-AlN)(Mo-Cr-V-Si)]_n have been developed.The introduction of additional alloying elements (Mo, Cr, V, Si) into the Ti-Al-N coating composition, which have a high affinity for nitrogen and are capable of forming strong nitride nanoparticles in the Ti-N and Al-N layers.This makes it possible to obtain hard and superhard hardening coatings.The metallographic and tribological studies carried out indicate the prospects of the developed multicomponent multilayer nano- and microstructured Avinit coatings for increasing wear resistance and reducing friction coefficients.This paper is devoted to the development and implementation of Avinit vacuum plasma technologies for strengthening cutting and forming tools to improve tool performance.Production tests of cutting tools with Avinit's developed multilayer wear-resistant ion-plasma coatings in production conditions at many large machine-building enterprises have shown their high efficiency.In serial production, the wear resistance of tools increases by 3 to 30 times, stamps by 5 to 100 times, and parts rubbing against abrasive materials by 10 to 100 times.Avinit's vacuum plasma technologies have been successfully implemented in production in the aggregate and engine building, transport engineering, and power engineering industries.Positive experience in applying multicomponent coatings has been gained not only when applying hardening coatings to manufactured cutting tools, but also after regrinding to regrindable carbide cutting tools from domestic and foreign manufacturers.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

With superior optical properties, high flexibility in engineering its material properties, and strong capability for large-scale on-chip integration, graphene oxide (GO) is an attractive solution for on-chip integration of two-dimensional (2D) materials to implement functional integrated photonic devices capable of new features. Over the past decade, integrated GO photonics, representing an innovative merging of integrated photonic devices and thin GO films, has experienced significant development, leading to a surge in many applications covering almost every field of optical sciences. This paper reviews the recent advances in this emerging field, providing an overview of the optical properties of GO as well as methods for the on-chip integration of GO. The main achievements made in GO hybrid integrated photonic devices for diverse applications are summarized. The open challenges as well as the potential for future improvement are also discussed.

Due to its time effective, joint friendly and highly customizable character whole-body-electromyostimulation (WB-EMS) is regarded as a feasible solution for a large variety of training issues particularly in the area of non-athletic application. To identify gaps in research and summarize prevalent evidence we conducted an evidence map on outcomes addressed by WB-EMS trials in middle-aged to older, non-athletic adults. Based on a comprehensive systematic search in five databases and two study registers according to PRISMA, 54 projects published in 80 articles were included. More than 90% of the studies reported outcomes related to the physical fitness or function domain. Body composition parameters were addressed by two thirds of the projects. Health-related outcomes addressed by WB-EMS included cancer/neoplasm (n=7), endocrine regulation (n=8), glucose metabolism (15), nervous system diseases (n=2), cardiovascular system diseases (n=22), non-specific chronic low back pain (n=4), osteopenia (n=5) and diseases of the renal system (n=12). Outcomes related to inflammation were addressed 18 times. Of importance, no studies reported clinically relevant adverse effects related to the WB-EMS intervention. In summary, while considerable evidence on outcomes related to fitness/function and body composition is prevalent, evidence gaps of WB-EMS research were particular evident for diseases of the nervous and cerebrovascular system.

Thin supported inorganic mesoporous membranes are used for removal of salts, small molecules (PFAS, dyes, polyanions) and particulate species (oil droplets) from aqueous sources with high flux and selectivity. Nano-filtration membranes can reject simple salts with 80-100% selectivity through a space charge mechanism. Rejection by size selectivity can be near 100% since the membranes can have a very narrow size distribution. Mesoporous membranes have received par-ticular interest due to their (potential) stability at operational conditions and defouling operations. More recently membranes with extreme stability became interesting with the advent of in-situ fouling mitigation by means of ultrasound, emitted from within the membrane structure. For this reason we explored the stability of available and new membranes with accelerated lifetime tests in aqueous solutions at various temperatures and pH values. Of the available ceria, titania, mag-netite membranes none were actually stable at all test conditions. In earlier work, it was already established that meso-porous alumina membranes have very poor stability. A new nano-filtration membrane was made of cubic zirconia membranes that exhibited a near perfect stability. A new ultra-filtration membrane was made of amorphous silica that was fully stable in ultrapure water at 80°C. This work provides details of membrane synthesis, stability characterization and actual sta-bility data.

In this work, we present a transceiver front-end in SiGe BiCMOS technology that can provide an ultra-wide bandwidth of 100 GHz at millimeter-wave frequencies. The front-end employs a novel configuration for low-loss distribution of broadband generated pulses as well as coherent spatial combining of received pulses. This leads to the realization of a fully integrated ultra-high-resolution imaging chip for biomedical applications. We realized an ultra-wide imaging bandwidth of 100 GHz by the integration of two adjacent, disjointed frequency sub-bands of 10–50 GHz and 50–110 GHz respectively. The transceiver front-end is capable of both transmit (TX) and receive (RX) operations. This is a key building-block for a scalable system in which a unit cell is repeated in the X and Y directions resulting in less power and area consumption. The imaging elements were designed and fabricated in Global Foundry 130-nm SiGe 8XP BiCMOS process technology.

Ultrafast laser 3D lithography based on non-linear light-matter interactions, widely known as multi-photon lithography (MPL), offers unrivaled precision rapid prototyping and flexible additive manufacturing options. 3D printing equipment based on MPL are already commercially available, yet there is still no comprehensive understanding of factors determining spatial resolution, accuracy, fabrication throughput, repeatability, and standardized metrology methods for the accurate characterization of the produced 3D objects and their functionalities. The photoexcitation mechanisms, spatial-control or photo-modified volumes, and the variety of processable materials are topics actively investigated. The complexity of the research field is underlined by limited understanding and fragmented knowledge of light-excitation and material response. Research to date has only provided case-specific findings on photoexcitation, chemical modification, and material characterization of the experimental data. In this review, we aim to provide a consistent and comprehensive summary of the existing literature on photopolymerization mechanisms under highly confined spatial and temporal conditions, where, besides the excitation and cross-linking, parameters such as diffusion, temperature accumulation, and the finite amount of monomer molecules start to become of critical importance. Key parameters such as, photoexcitation, polymerization kinetics, and the properties of the additively manufactured materials at the nanoscale in 3D are examined, whereas, the perspectives for future research and as well as emerging applications are outlined.

Micro-plasma is generated in ultra-high-pure hydrogen gas filled inside a cell at a pressure of (1.08 ± 0.033) × 10⁵ Pa (810 ± 25 Torr) by using a Q-switched Nd:YAG laser device operated at 1064 nm wavelength and 14 ns pulse duration. Micro-plasma emission spectra of the hydrogen Balmer alpha line, H_α, are recorded with a Czerny-Turner type spectrometer and an intensified charge-coupled device. The spectra are calibrated for wavelength and corrected for detector sensitivity. During the first few tens of nanoseconds after initiating optical breakdown, significantly Stark-broadened and Stark-shifted H_α lines mark the well-above hypersonic outward expansion. The vertical diameters of the spectrally resolved plasma images are measured for time delays of 10 ns to 35 ns to determine expansion speeds of the order of 100 km/s to 10 km/s. For time delays of the order of 0.5 µs to 1 µs, the expansion decreases to the speed of sound of 1.3 km/s in the near ambient temperature and pressure hydrogen gas.

The article presents tests aimed to verify the possibility of making T-joints in TMCP steel using laser. The tests involved the use of 10 mm thick high yield point steel S700MC obtained in an industrial manufacturing process. The joints made in the tests were single and double-sided. Subsequent non-destructive tests revealed that the joints obtained in the tests represented quality level B in accordance with PN-EN ISO 13919-1. Single-sided welding performed using the laser beam having a power of 11 kW enabled the obtainment of 8 mm deep penetration without visibly deforming the web of the joint. The double-sided welded joints were characterised by proper geometry and the presence of gas pores in the welds not compromising the requirements of quality level B (strict requirements). The weld structure was bainitic-ferritic. The weld hardness was by approximately 60 HV1 higher than that of the base material (280 HV1). The HAZ area was slightly softer than the base material. The tests of thin foils performed using a high-resolution scanning transmission electron microscope revealed that, during welding, an increase in the content of the base material in the weld was accompanied by an increase in contents of alloying microagents Ti and Nb, particularly near the fusion line. The above-named alloying microagents, in the form of fine-dispersive (Ti,Nb)(C,N) type precipitates, could reduce plastic properties of joints.

The development of smart negative electrode materials with high capacitance for use in supercapacitors remains challenging. Although there have been several types of electrode materials with high capacitance used in energy storage, carbon-based materials are the most reliable electrodes due to their high conductivity, high power density and excellent stability. The most common complaint about general carbon materials is that these as-formed electrode materials can hardly ever be used as free-standing electrodes. Free-standing carbon-based electrodes are in high demand and are a passionate topic of energy storage research. Electrospun nanofibers are a potential candidate to fill this gap. However, the as-spun carbon nanofibers (ECNFs) have low capacitance and energy density on their own. To this end, several attempts have been made to improve these characteristics. In this review, we introduce negative electrode materials that have been developed. Moreover, this review places special attention to the advances of electrospun nanofiber-based negative electrode materials and their limitations. Based on the above information, we put forth a future perspective on how these limitations can be overcome to meet the demands of next-generation smart devices.

Non-standard diesel blends can be harmful to the environment and human health. In this context, a simple analytical method to estimate the biodiesel mixture ratio in diesel was developed based on the impedance spectroscopy (IS) associated with the interdigitated sensors. In this article, four different interdigitated sensors, variable comb spacing (G), were simulated using the COMSOL Multiphysics software. Based on finite element simulations, four interdigitated electrode architectures by manufactured and evaluated. According to the X-ray powder diffraction technique, the deposition of the conductive layer (Au°) over the surface of the dielectric substrate (SiO2) did not alter its phase composition. In the analysis of AFM and SEM, it was possible to observe irregular edges on the electrodes, possibly related to thin layers' manufacturing process and mechanical stability. Another characteristic observed in the AFM images was the height of the step of the gold layer of the sensor. Several cross-sections were obtained, and the mean step value is 225.71 ± 0.0032 nm. Although there are differences in the roughness, the whole sensor has nanometric roughness. Based on the finite element method simulation performed, it can be assumed that the geometric parameters more suitable for the manufacturing of the electrode are: W = 20 µm, L = 1000 µm, G = 50 µm e N = 40 digits. The electrical characterization performed by impedance spectroscopy showed that we could differentiate between biodiesel and diesel fuels and their pseudo-binary mixtures in the low-frequency region.

The aims of this work were to examine the new electrode, based on polymer bacteria modified aluminum electrode for simultaneous production of electricity and degradation of phenol. This electrode is based aluminum modified by bacteria inserted in the polymer matrix, developed in situ on the surface. This electrode, designated subsequently by bacteria-polymer-aluminum, Showed stable response and was characterized with voltametric methods, as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The experimental results revealed that the prepared electrode could be a feasible for degradation of hazardous phenol pollutants. The sensor was successfully applied to the determination of phenol in a real sample with satisfactory results.

The reported study was devoted to the investigation of viscoelastic behavior for solid and porous ultra-high-molecular-weight polyethylene (UHMWPE) under compression. The obtained experimental stress curves were interpreted using a two-term Prony series to represent the superposition of two coexisting activation processes corresponding to long molecular (~160 s) and short structural (~20 s) time scales, respectively, leading to good statistical correlation with the observations. In the case of porous polymer, the internal strain redistribution during relaxation was quantified using Digital Image Correlation (DIC) analysis. The strongly inhomogeneous deformation of the porous polymer was found not to affect the relaxation times. In order to generalize the results to three dimensions, X-ray tomography was used to examine the porous structure at the macro- and micro-scale levels. DIC analysis revealed positive correlation between the applied force and relative density. The apparent stiffness variation for UHMWPE foams with mixed open and closed cells was described using a newly proposed three-term expression. Furthermore, the in situ tensile loading and X-ray scattering study was applied for isotropic solid UHMWPE specimens to investigate their parameters of internal structure during orientation and stress relaxation process at another mode.

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

The microstructure and hardness along the thickness direction of a water quenched, high-strength thick plate with a thickness of 40 mm were investigated with three specimens from the thick plate: surface, 1/4t, and 1/2t (center) thickness, and the phase transformation behavior of the thick plate according to the cooling rate was analyzed through dilatometric experiments. Finally, the cooling rate for each thickness of the thick plate was estimated by comparing the microstructure and hardness of the thick plate along the thickness with those of the dilatometric specimens. Martensite microstructure was observed on the surface of the water quenched thick plate due to the fast cooling rate. On the other hand, an inhomogeneous microstructure was transformed inside the thick plate due to the relatively slow cooling rate and central segregation of Mn. A small fraction of bainite was shown at 1/4t thickness. A banded microstructure with martensite and bainite resulting from Mn segregation was developed at 1/2t; that is, the full martensite microstructure was transformed in the Mn-enriched area even at a slow cooling rate due to high hardenability, but a bainite microstructure was formed in the Mn-depleted area owing to relatively low hardenability. A portion of martensite with fine cementite at the surface and 1/4t was identified as auto-tempered martensite with a Bagaryatskii orientation relationship between the ferrite matrix and cementite. The microstructure and hardness as well as dilatation were investigated at various cooling rates through a dilatometric experiment, and a continuous cooling transformation (CCT) diagram was finally presented for the thick plate. Comparing the microstructure and hardness at the surface, 1/4t, and 1/2t of the thick plate with those of dilatometric specimens cooled at various cooling rates, it was estimated that the surface of the thick plate was cooled at more than 20 oC/s, whereas the 1/4t region was cooled at approximately 5 ~ 10 oC/s during water quenching.

The present work deals with the development of finite element methodology for obtaining the stress distributions in thick cylindrical HK40 stainless steel pipe that carry high temperature fluids. The material properties and loading are assumed to be random variables. Thermal stresses that are generated along radial, axial and tangential directions are computed generally using analytical expressions which are very complex. To circumvent such an issue, the probability theory and mathematical statistics have been applied to many engineering problems which allows to determine the safety both quantitatively and objectively based on the concepts of reliability. Monte Carlo simulation methodology is used to study the probabilistic characteristics of thermal stresses which is used for estimating the probabilistic distributions of stresses against the variations arising due to material properties and load. A 2-D Probabilistic finite element code is developed in MATLAB and the deterministic solution is compared with ABAQUS solutions. The values of stresses that are obtained from the variation of elastic modulus are found to be low as compared to the case where the load alone is varying. The probability of failure of the pipe structure is predicted against the variations in internal pressure and thermal gradient. These finite element framework developments are useful for the life estimation of piping structures in high temperature applications and subsequently quantifying the uncertainties in loading and material properties.

Assessing observation noise is a critical step in the development of a stochastic model for GNSS navigation and positioning. This process ensures that the statistical properties of the observational data are accurately characterized, leading to more reliable and precise positioning results. Traditionally, the one sigma values for observation noise, 0.3 m for code and 3 mm for carrier phase, alongside elevation-dependent weighting schemes, have been standard. However, these may no longer be suitable due to significant advancements in GNSS systems, receivers, and antennas. Previous research predominantly focused on code type and PPP techniques, often limited by the inability to separately assess observation types across different frequency bands due to ionospheric delay. Furthermore, these studies were generally constrained by limited experimental data. This research advocates for the use of ultra-short baselines to eliminate atmospheric delay and other error sources, providing a detailed assessment of observation noise for various frequency bands, GNSS systems, and receiver & antenna types over an extensive period and across multiple baselines. The findings suggest a need to reconsider traditional one sigma values and elevation-dependent weighting schemes for current applications.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Heart rate variability (HRV) is commonly intended as the variation in the heart rate (HR) and it is evaluated in the time and frequency domains with various well known methods. In the present paper, we first consider an abstract model in which the HR is the instantaneous frequency of an otherwise periodic signal such as the electrocardiogram (ECG). Thus the ECG is assumed as a frequency modulated signal, or carrier signal, where HRV or HRVt is a supposed time-domain signal which is frequency modulating the carrier ECG signal around its average frequency. Hence we describe an algorithm able to frequency demodulate the ECG signal to extract a continuous signal HRVt with possibly enough time resolution to analyse fast time-domain variations in the instantaneous HR. After exhaustive testing of the method on simulated frequency modulated sinusoidal signals, we have applied the procedure on actual ECG tracings. The purpose of the work is to eventually use the heart as a kind of biological sensor of the fast activity of the autonomous nervous system (ANS) to study the ANS ultra-short-term event-evoked responses. A few preliminary, not clinical, real examples are also given.

VANET networks are a class of peer-to-peer wireless networks that are used to organize communication between cars (V2V), cars and infrastructure (V2I) and between cars and other types of nodes (V2X). These networks are based on the DSRC, 802.11 standards and are mainly intended for organizing the exchange of various types of messages, mainly emergency ones, to prevent road accidents or alert when road accident occur, or control the priority of the driveway. Initially it was assumed that cars would only interact with each other, but later, with the advent of the concept of Internet of things (IoT). Researchers began to analyze connectivity with other devices, which in general will allow to combine various road users and other devices that can used in the creation of intelligent transport infrastructure in a single smart city management system. Infrastructure is necessary for the provision of services, monitoring and management of the VANET network. As infrastructure objects it is proposed to use stationary objects of Roadside unit (RSU). The aim of this paper is to analyze the use of mobile edge computing to decrease the load to the base station and latency between RSU clouds and provide a real experiment using software defined networking and mobile edge computing for RSU.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

Marine renewable energy technologies have a great potential in supplying clean electricity to millions of people across the globe, if technical and economic conditions are in right. So far, ocean energy projects are commonly started by SMEs or educational institutions with limited budgets. Therefore, any effort to reduce expenses is of great value. One of the areas involving substantial expenses are the inevitable seabed inspection prior to deployment of marine renewable energy device. Detailed seabed inspections can also reduce the risk of associated with deployment of structures on uneven seabed, especially marine renewable energy devices with gravity foundations. By reducing the costs and risks of such surveys prior and during the installation phases, the feasibility of marine renewable energy projects can be more favoured and competitive. In this perspective, this study proposes a cost and time effective technique for seabed surveys. The proposed technique involves the use of high precision and inexpensive sonar systems and underwater optical cameras integrated into a versatile and compact subsea monitoring platform. It also involves simple and practical data acquisition and processing protocols that do not requires hi expertise for operation. The results obtained showed that high resolution bathymetric maps and detailed seabed inspections imagery can be acquired. This study concludes that a simple and inexpensive subsea monitoring platform comprising a multibeam, dual beam and video cameras can be effective for high resolution seabed inspection and bathymetric measurements for marine energy applications.

An effective approach to fabricate large-scale of conducting polyaniline (PANI) by an in situ anodic electrochemical polymerization on the nickel foam, which coated by a novel aryl diazonium salt (ADS)-functionalized graphene (ADS-G). In present work, ADS-G was used as a high surface area support material for electrochemical polymerization of PANI. Electrochemical performances of the ADS-G/PANI composites exhibited better suitability as supercapacitor electrode materials than that of the PANI. The ADS-G/PANI composites achieved the specific capacitance of 528 F g-1, which was higher than that of PANI (266 F g-1) due to the excellent electrode-electrolyte interaction and synergistic effect of electrical conductivity between ADS-G and PANI in the composites. These findings suggested that the ADS-G/PANI composites were a suitable composite for the potential supercapacitor applications.

In this work we successfully prepared a modified cobalt oxide (Co3O4) carbon paste electrode to detect Levofloxacin (LEV). By synthesizing Co3O4 nanoparticles through the chemical coprecipitation method, the electrochemical properties of the electrode and LEV were thoroughly investigated using CV, SWV, EIS, while material properties were scrutinized using ICP-OES, TEM, SEM, and XRD. The results showed that the prepared electrode displayed a better electrocatalytic response than the bare carbon paste electrode. After optimizing SWV, the electrode exhibited a wide linear working range from 1 to 85 μM at pH 5 of BRBS as the supporting electrolyte. The selectivity of the proposed method was satisfactory, with good repeatability and reproducibility, strongly suggesting a potential application for determining LEV in real samples, particularly in pharmaceutical formulations. The practicality of the approach was demonstrated through good recoveries, and the morphology of the materials was found to be closely related to other parameters, indicating that the developed method can provide a cost-effective, rapid, selective, and sensitive means for LEV monitoring. Overall, this project has made significant progress towards developing a reliable method for detecting LEV and has opened up new opportunities for future research in this field.

In this study, the preparation of the composite 3% Au/graphite-C3N4 (3% Au/g-C3N4) sensing material was prepared by doping 3% Au onto the surface of graphitic carbonitride (C3N4) for detection pimobendan. By the way of sensing materials characterization, the X-ray diffraction analysis (XRD) and transmission electron Microscope (TEM) were performed. The cyclic voltammetry (CV) was used to measure the concentration and redox properties of pimobendan. It can be seen that when the voltage value is 0.05 V, and a reduction peak was appeared and the pimobendan concentration (0 to 55 μM) has a relationship with the reduction current value. At low concentrations of pimobendan concentration from 0.0 to 0.8 μM, the linearity R2 = 0.9642 with a detection limit of 0.28 μM. A possible pimobendan sensing mechanism on 3% Au/g-C3N4 was proposed.

The present review article concludes with three different types of materials recently used to enhance the efficiency of supercapacitors. The first type involves carbon-based materials for storage and supercapacitor applications. The carbon materials could be obtained naturally and synthesized manually based on the needs. The second type discusses the recent advances in metal oxide materials for high-performance supercapacitors. The metal oxide materials involve in different types of attachment through the bi-tri metallic bonding, which enhances the specific capacitance. The third type involves recently advanced materials for high energy and power density application. The power and energy density of the materials is enhanced by the surface modification of the materials. In recent days, the MXene and Nano-composite materials seems to be an appropriate material to increase the power and energy density of the device.

Population growth and increasing global demand for freshwater have raised a serious challenge for the depleting sources of freshwater in the 21st century. Desalination technologies can be a reliable technique for providing freshwater. Capacitive deionization is one of the innovative desalination methods that has received increasing interest. Flow-electrode capacitive deionization (FCDI) (a new architecture of capacitive deionization) is one of the efficient, cost-effective, and environmentally-friendly desalination methods for freshwater production. In this experimental research, the performance of an FCDI system was investigated and the influence of important parameters such as flow rate of flow-electrodes, electrolyte salt concentration of flow-electrodes, and initial feed water concentration will be assessed on the efficiency of desalination operation. In this study, the flow-electrodes operated in short-circuited closed-cycle operation (SCC) mode, and also the feed water operated similarly to the flow-electrodes in closed-cycle. Moreover, in all the experiments, the salt adsorption capacity (SAC) and salt removal efficiency (SRE) was calculated. Herein, by optimizing the above mentioned parameters, the salt removal efficiency of 83% and a SAC value of 29.12 mg/g dry carbon were achieved in 5 hours.

Laser reduced graphene oxide (LRGO) on a PET substrate was prepared in one-step to obtain the LRGO grid electrode for sensitive carbaryl determination. The grid form results in a grid distribution of different electrochemically active zones affecting the electroactive substance diffusion towards to the electrode surface and increasing the electrochemical sensitivity for carbaryl determination. Carbaryl is electrochemically irreversibly oxidized by the secondary amine moiety of the molecule with the loss of one proton and one electron in the pH range from 5 to 7 by LSV on the LRGO grid electrode with a scan rate of 300 mV/s. Some interference of the juice matrix molecules did not significantly affect the LSV oxidation current of carbaryl on the LRGO grid electrode after adsorptive accumulation without applied potential. The LRGO grid electrode can be used for LSV determination of carbaryl in fruit juices in the concentration range from 0.25 to 128 mg/L with LOD of 0.1 mg/L by. The fabrication of the LRGO grid electrode opens up possibilities for further inexpensive monitoring of carbaryl in other fruit juices and fruits.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

In this work, we focus on investigating electrothermal flow in a rotating electric field (ROT-ETF), with primary attention paid to the horizontal traveling-wave electrothermal (TWET) vortex induced at the center of the electric field. The frequency-dependent flow profiles in the microdevice are analyzed using different heat transfer models. Accordingly, we address in particular the importance of electrode cooling in ROT-ETF as metal electrodes of high thermal conductivity while substrate material of low heat dissipation capability are employed to develop such microfluidic chips. Under this circumstance, cooling of electrode array due to external natural convection on millimeter-scale electrode pads for external wire connection occurs and makes the internal temperature maxima shift from the electrode plane to a bit of distance right above the cross-shaped interelectrode gaps, giving rise to reversal of flow rotation from a typical repulsion-type to attraction-type induction vortex, which is in good accordance with our experimental observations of co-field TWET streaming at frequencies on the order of reciprocal charge relaxation time of the bulk fluid. These results point out a way to make a correct interpretation of out-of-phase electrothermal streaming behavior, which holds great potential for handing high-conductivity analytes in modern microfluidic systems.

The utilization of dual-potential mode of integrated array (IDA) electrodes and other two-electrode systems has revolutionized electrochemical detection by enabling the simultaneous and independent detection of two species, accompanied by the exhibition of unique characteristics. In contrast to conventional dual-potential electrodes, the rotating ring disk electrodes (RRDE), IDA electrodes demonstrate analogous yet vastly improved performance metrics, characterized by remarkable collection efficiency and sensitivity. Notably, due to the distinctive microscale structure of IDA electrode, the special “feedback” effect makes IDA a unique signal amplifier. In recent decades, the research surrounding IDA electrodes has garnered escalating interest due to their attractive attributes. This review centers its focus on the fabrication and applications of IDA electrodes. In the realm of fabrication, two critical breakthroughs are poised for realization: the achievement of reduced dimensions and the diversification of materials. Established fabrication methods for IDA electrodes encompass photolithography, inkjet printing, and direct laser writing, each affording distinct advantages in terms of size and precision in IDA construction. Predominantly employed materials for IDA electrodes include gold, platinum, and carbon, with the selection of fabrication methods guided by considerations such as material properties, desired dimensions, cost-efficiency, and specific application requisites. Within the domain of applications, IDA electrodes, capitalizing on their distinctive attributes, have found utility in diverse fields. This review summarizes the applications of IDA electrodes based on their fundamental working principles, encompassing redox cycling, resistance modulation, capacitance variations, and more. The potential for further development of this specialized tool to exhibit enhanced properties holds substantial promise.

The inhibition of localised corrosion is known to involve multiple processes taking place over a range of time and length scales that are difficult to study by conventional electrochemical methods. This work demonstrates an approach to probing complex localised electrochemical processes by combining an electrochemically integrated multi-electrode array (also known as wire beam electrode (WBE)), scanning vibrating electrode technique, scanning electrochemical microscopy and surface analytical techniques. Each technique reveals certain aspects of the dynamically changing, multi-scale, inhibitor-microstructure interactions and local chemistry over a heterogeneous AA2024-T3 alloy surface in the presence of an environmentally friendly inhibitor; cerium diphenyl phosphate (Ce(dpp)3).

The DEP force is usually calculated from the object’s point of view using the interaction of the object’s induced dipole moment with the inducing field. Recently, we described the DEP behavior of high- and low-conductive 200-µm 2D spheres in a square 1x1mm chamber with a plane-versus-plane electrode configuration from the system’s point of view. Here we extend our previous considerations to the plane-versus-plane and pointed-versus-pointed electrode configurations. The trajectories of the sphere center and the corresponding DEP forces were calculated from the gradient of the system’s overall energy dissipation for given starting points. The dissipation’s dependence on the sphere’s position in the chamber is described by the numerical “conductance field”, which is the DC equivalent of the capacitive charge-work field. While the plane-versus-plane electrode configuration is field-gradient free without an object, the presence of the highly or low-conductive spheres generates structures in the conductance fields, which result in very similar DEP trajectories. For both electrode configurations, the model describes trajectories with multiple endpoints, watersheds, and saddle points, very high attractive and repulsive forces in front of pointed electrodes, and the effect of mirror charges. Because the model accounts for inhomogeneous polarization within the objects, the approach allows the modeling of the complicated interplay of attractive and repulsive forces near electrode surfaces and chamber edges. Non-reversible DEP forces or asymmetric magnitudes for the highly and low-conductive spheres in large areas of the chamber indicate the presence of higher-order moments, mirror charges, etc.

During HVDC earth return operation systems, a high magnitude current will be injected into soil through earth electrode, the potential on the surface would change widely and produce unfavorable effects on the AC systems around. This paper presents an effective finite element method (FEM) coupling electric field with thermal field to evaluate the electrical field induced by the injected DC current. Firstly, owe to the characteristic of FEM, this method can consider arbitrary soil and earth electrode structure. Secondly, by setting the electrical and thermal parameters of soil as a function of temperature at the same time, the dynamic coupling process of electric field and thermal field is simulated accurately. Thirdly, to deal with the singular point in FEM subdivision and the huge computation in traditional three-dimensional FEM, the FEM coupling 2-D earth electrode with 3-D soil based on "shell" theory is introduced. Finally, based on the suggested method, the effect of abnormal resistance region (ARR) near DC earth electrode on electric field distribution is analyzed.

This paper reviews several techniques, including analytical theories and real frequency techniques, to design ultra-wideband impedance matching networks for low-power applications. The comparison of solutions obtained using the simplified real frequency technique to the published solution using Chebyshev filter theory is demonstrated.

This article explores the implementation of high accuracy GPS denied Ad-Hoc localization. There is little research on Ad-Hock UWB-enabled localization systems with mobile and stationary nodes. This work aims to demonstrate the localization of bicycle-modeled robots in a non-static environment through a mesh network of mobile, stationary robots and ultra-wideband sensors. The non-static environment adds a layer of complexity when actors can enter and exit the node’s field of view. The method starts with an initial localization step where each unmanned ground vehicle (UGV) uses the surrounding, available anchors to derive an initial local or, if possible, global position estimate. The initial localization uses a simplified implementation of the iterative multi-iteration Ad-Hoc Localization System (AHLos). This estimate was refined using an unscented Kalman filter (UKF) following a constant turn rate and velocity magnitude model (CTRV). The UKF fuses the robot’s odometry and the range measurements from the Decawave ultra-wideband receivers stationed on the network nodes. Through this position estimation stage, the robot broadcasts to its neighbors its estimated position to help the others further improve their localization estimates and localize themselves. This wave-like cycle of nodes helping to localize each other allows the network to act as a mobile Ad-Hoc localization network.

Although Sugarcane bagasse ash (SCBA) has good cementitious property, previous researchers have primarily aimed to improve the mechanical performance of conventional concrete or cement-based composites. Research is lacking on ultra-high performance concrete (UHPC), especially regarding tensile self-sensing properties. This paper aimed to comprehensively evaluate the SCBA effect on the UHPC’s mechanical, electrical, and tensile self-sensing properties. The results showed that SCBA below the critical incorporation concentration (CIC) improved the UHPC’s mechanical properties compared to steel fibers alone. Furthermore, adding 3.0wt% SCBA remarkably enhanced the UHPC mechanical properties where the compressive, flexural, and tensile strengths increased by 13.1%, 17.4%, and 20.6%, respectively. The SCBA content of 0.3wt% achieved the maximum UHPC electrical resistivity since values smaller or greater than this content decreased the resistivity. The SCBA-enhanced UHPC showed better tensile stress-sensing performance than UHPC without SCBA due to improved linearity and reversibility, lower hysteresis, higher sensitivity, and superior repeatability. UHPC with 0.3wt% SCBA achieved the best linearity, while UHPC with 0.9wt% SCBA showed the highest sensitivity, lowest hysteresis, and best repeatability. Overall, the content of 0.9wt% SCBA is the best in improving the overall mechanical, electrical, and tensile self-sensing performance.

Bending waveguide is one of the building blocks of on-chip photonic integrated circuits (PICs). Previous bending waveguides (BWs) usually suffer from larger footprint size in the bending region, which is are not conducive to develop large-scale and high-density PICs. To this end, we propose and numerically investigate an ultra-compact silicon-on-insulator 180-degree waveguide bend with a bending radius of 2 µm. Being different from the previous BWs, the design is based on topologically optimized digital metamaterials, which is implemented by using intelligent genetic algorithms. Simulated results show that the proposed structure has a -1.36 dB bend efficiency per 180-degree at a wavelength of 1.55 µm and occupies a footprint of only 4 × 4 µm2. Moreover, the crosstalk is <−20 dB and the loss is <2.6 dB over a >100 nm operating bandwidth (1.6-1.7 µm) for TE0 modes. With the wide operating bandwidth and ultra-compact footprint, the proposed silicon-based 180-degree waveguide bend shows a potential application as the fundamental component for optical communication interconnect in the ultra-highly integrated photonic circuit.

Novel approaches under the extreme conditions of ultra-high gravity of a super massive black hole allow us to assume that the spacetime degrades into the single dimension of time. A unique interpretation of the non-relativistic Schrödinger equation together with the relativistic Klein-Gordon and Dirac equations is presented by swapping the three dimensional space derivatives with the singular time derivative in the D’Alembertian operator. This apparatus reveals a unique time dependent wave equation that results in some implications such as possible time quantization with the intervals of around 3.36 × 10−21 ? which is in the order of uncertainty in time, ∆? = 1.3 × 10−21 ?, calculated from the energy-time version of the Heisenberg uncertainty principle for electrons. As a result of this, an antisymmetric wave function around the edge of the event-horizon zone appears and indicates that the virtual particle-antiparticle pairs of the electron field split into two real components with the spin-up and down states, reconfirming the Hawking radiation. Energy eigenvalues calculated from the application of the Dirac equation satisfies the preservation of energy and charge. The wave equation invoked in this study reduces into the time dependent Dirac equation within the neighborhood of zero-point, ? = 0, insuring the relevance of the evaluations.

We prepared heterogeneous alumina-silicate glasses by consolidating nanoparticles using molecular dynamics simulations. Consolidated glasses from either low alumina content alumina-silicate glasses or high alumina content alumina-silicate glasses show significantly improved ductility around consolidation pressure of ~3 GPa. The introduced structural heterogeneities, namely over-coordinated network formers and their neighboring oxygen atoms, are identified as plasticity carriers due to their high rearrangement propensity. In addition, consolidated oxide glass from both 23.4Al₂O₃76.6SiO₂ and 73.1Al₂O₃26.9SiO₂ nanoparticles show improved flow strength (up to 1 GPa) due to the introduction of chemical heterogeneities. Last but not least, apparent hardening behavior appears upon cold work in consolidated glasses, with an increase of yield strength from ~3.3 GPa to ~6.4 GPa. This method is a big advancement toward ultra-strong and ultra-tough glasses by breaking the structure, composition and size limitations in traditional melt-quench process.

Ultra-wide field optical coherence tomography (UWF-OCT) has been recently introduced into clinical ophthalmological practice. To date, there is little data on the reference values of retinal thickness (RT) and choroidal thickness (CT) measured with this technique. This study aimed to analyze the variance of RT and CT in healthy eyes with UWF-OCT tests performed with the largest available scan size of 23 x 20 mm. The data were analyzed with reference to the patients' age, gender, and the axial length of the eyeball. The results of UWF-OCT scanning enabled us to picture the shape of the retina and choroid in a large portion of the eyeball. Both anatomical entities become significantly thinner at the periphery. The peripheral CT is greater in the upper and temporal sectors; the RT is higher in the nasal compared to the temporal sectors. Both choroid and retina lose thickness with age, however, CT and RT do not show a statistically significant correlation with the axial length after adjusting for age and gender. Age-related variations in thickness are especially prominent in the choroid. The CT in UWF-OCT testing is significantly greater in females while the RT is greater in males. UWF-OCT testing provides additional information on the anatomical structure of the retina and choroid compared to standard-field OCT

Objective: To evaluate the existing meta-analytic evidence of associations between exposure to ultra-processed foods, as defined by the Nova food classification system, and adverse health outcomes. Design: Systematic umbrella review of existing meta-analyses. Data Sources: MEDLINE, PsycINFO, Embase, and the Cochrane Database of Systematic Reviews, as well as manually searching reference lists from 2009 to June 2023. Inclusion Criteria: Systematic reviews and meta-analyses of cohort, case-control, and/or cross-sectional study designs that evaluated the associations between exposure to ultra-processed foods and adverse health outcomes in humans across the lifespan. Results: The search identified 45 unique pooled analyses, including 13 dose-response and 32 non-dose-response associations (n=9,888,373). Overall, direct associations were found between exposure to ultra-processed foods and 32 (71%) health outcome domains spanning cardiometabolic, gastrointestinal, and respiratory conditions, cancer, mental health, and mortality. Based on a pre-specified evidence classification criteria, convincing evidence (Class I) supported direct associations between greater ultra-processed food exposure and higher risks of incident cardiovascular disease-related mortality (RR: 1.50; 95%CIs: 1.37 to 1.63), type two diabetes (dose-response RR: 1.12; 95%CIs: 1.11 to 1.13), and depressive outcomes (HR: 1.21; 95%CIs: 1.16 to 1.28), as well as higher risks of prevalent anxiety outcomes (OR: 1.48; 95%CIs: 1.37 to 1.59) and combined common mental disorder outcomes (OR: 1.53; 95%CIs: 1.43 to 1.63). Highly suggestive (Class II) evidence indicated that greater exposure to ultra-processed foods was directly associated with higher risks of incident all-cause mortality (RR: 1.21; 95%CIs: 1.15 to 1.27), heart disease-related mortality (dose-response HR: 1.66; 95%CIs: 1.51 to 1.84), and type two diabetes (OR: 1.40; 95%CIs: 1.23 to 1.59), together with higher risks of prevalent obesity (OR: 1.55; 95%CIs: 1.36 to 1.77), adverse sleep-related outcomes (OR: 1.41; 95%CIs: 1.24 to 1.60), and wheezing (RR: 1.40; 95%CIs: 1.27 to 1.55). Out of the remaining 34 pooled analyses, 21 were graded as suggestive or weak strength (Class III-IV) and 13 were graded as no evidence (Class V). Using the GRADE framework, 22 pooled analyses were rated as "Low" quality, with 19 rated as "Very Low” and four rated as "Moderate" quality. Conclusions: Higher exposure to ultra-processed food was associated with a greater risk of adverse health outcomes, especially cardiometabolic, common mental disorder, and mortality outcomes. These findings provide a rationale to evaluate the effectiveness of using population-based measures to target and reduce dietary exposure to ultra-processed foods for improved human health. Systematic Review Registration: PROSPERO CRD42023412732.

Screen-printed carbon electrode (SPCE) is a useful technique that has been widely used in the practical application of biosensors oriented to point-of-care testing (POCT) due to its characteristics of cost-effectiveness, disposability, miniaturization, wide potential window, and easy of electrode design. Compared with gold or platinum electrodes, surface modification is difficult because the carbon surface is chemically or physically stable. Oxygen plasma can easily produce carboxyl groups on the carbon surface, which act as scaffolds for covalent bonds. However, the effect of O2-plasma treatment on electrode performance remains to be investigated from an electrochemical perspective, and sensor performance can be improved by clarifying the surface conditions of plasma treated biosensors. In this research, we compared antibody modification by plasma treated and physical adsorption, using our original immunosensor based on gold nanoparticles (AuNPs). Consequently, the O2-plasma treatment produced carboxyl groups on the electrode surface, which changed the electrochemical properties owing to electrostatic interactions. It was also found that the surface became hydrophilic, inhibiting non-specific antigen adsorption. The sensitivity was 6.5 times higher than the Limit of Detection (LOD) using physical adsorption.

A gold nanostructured film modified glassy carbon electrode (Au_film/GCE) was developed for the determination of chromium (VI) in water sample. GCE was immersed into HAuCl₄ solution (10^-3M) and electrodeposition of thin gold layer was conducted at –0.4 V (vs Ag/AgCl) for 10 min. The strong affinity between Au and Cr species resulted with increasing of Cr (VI) signal, compared with the bare glassy carbon electrode. The electrodepositing time, type of supporting electrolyte, pH, the scan rate, modulation amplitude, and modulation time were optimized using differential pulse anodic stripping voltammetry (DP-ASV). The calibration graph using accumulation time of 120 s was linear from 10 to 120 µgL^-1 with a sensitivity 1.3 x 10^-2 µA/µgL^-1. Under optimum experimental conditions, a good correlation coefficient R²=0.9971, and a low detection limit 5.5 µg/L Cr (VI) was obtained. The signal was reproducible with a relative standard deviation ±4.5 %. The developed Au_film/GCE sensor was applied for the Cr (VI) determination of in sewage water samples.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Progress in laser-driven proton acceleration requires increasing the proton maximum energy and laser-to-proton conversion efficiency, while reducing the divergence of the proton beam. However, achieving all these qualities simultaneously has proven challenging experimentally, the increase in beam energy often coming at the cost of beam quality. Numerical simulations suggest that coupling multi-PW laser pulses with ultrathin foils could offer a route for such simultaneous improvement. Yet experimental investigations have been limited by the scarcity of such lasers and the need for very stringent temporal contrast conditions to prevent premature target expansion before the pulse maximum. Here, combining the newly commissioned Apollon laser facility that delivers high-power ultrashort (∼24fs) pulses, with a double plasma mirror scheme to enhance its temporal contrast, we demonstrate the generation of up to 35 MeV protons with only 5 J of laser energy. This approach also achieves improved laser-to-proton energy conversion efficiency, reduced beam divergence, and optimized spatial beam profile. Therefore, despite the laser energy losses induced by the plasma mirror, the proton beams produced by this method are enhanced on all accounts compared to those obtained under standard conditions. Particle-in-cell simulations reveal that this improvement results from the intensified electrostatic field caused by a more compact hot-electron distribution.

In the steeply inclined and extremely thick coal seams (SIETCS) mined using the horizontal sublevel top-coal caving (HSTCC) method, the uncertainty of gas emission is a safety threat to the mining operations. In order to reduce the occurrence of accidents, the determination of gas emission is crucial. In this paper, we first proposed a prediction model for workers at the floor coalbed to calculate gas emission on site. We then put forward a finite element numerical simulation for researchers to predict gas emission from the floor coalbed. At last, we measured gas emitted from the floor coalbed of SIETCS in Wudong Coal Mine in a specific mining period and used the data to verify the applicability and accuracy of these two gas-emission prediction methods. The results showed that the gas emission from Wudong Coal Mine was 1.08 m³/min calculated based on the prediction model and 1.07 m³/min obtained using the user-defined integration method. Both methods have their own advantages, disadvantages and applicable objects, and are important in predicting gas emission from SIETCS mined using HSTCC method.

Energy efficiency considerations in terms of reduced power dissipation is a significant issue in the design of digital circuits for very large-scale integration (VLSI) systems. Quantum-dot cellular automata (QCA) is an emerging ultra-low power dissipation approach, distinct from the traditional complementary metal-oxide semiconductor (CMOS) technology, for building digital computing circuits. Developing fully reversible QCA circuits has the potential to significantly reduce energy dissipation. The multiplexer is a fundamental element in the construction of useful digital circuits. In this paper, a novel, multilayer, fully reversible QCA 8:1 multiplexer circuit, with ultralow energy dissipation, is introduced. The proposed multiplexer power dissipation is simulated using the QCADesigner-E version 2.2 tool, describing the microscopic physical mechanisms underlying the QCA operation. The results showed that the proposed reversible QCA 8:1 multiplexer consumes 89% less energy than the most energy-efficient 8:1 multiplexer circuit presented previously in the scientific literature.

Integrated ultra-low-loss waveguides are highly desired for integrated photonics to enable applications that require long delay lines, high-Q resonators, narrow filters, etc. Here we present an ultra-low-loss silicon waveguide on 500 nm thick SOI platform. Meter-scale delay lines, million-Q resonators and tens of picometer bandwidth grating filters are experimentally demonstrated. We design a low-loss low-reflection taper to seamlessly integrate the ultra-low-loss waveguide with standard heterogeneous Si/III-V integrated photonics platform to allow realization of high-performance photonic devices such as ultra-low-noise lasers and optical gyroscopes.

A novel method based on a hybrid incremental modeling approach has been designed and applied to imbalance detection in ultra-high precision rotating machines. The model is obtained by a two-step iterative process that combines an overall model (least-squares fitting) with a local model (fuzzy k-nearest-neighbour) to take advantage of their complementary capacities. Three normalization strategies of evaluating the effect on accuracy are analyzed. A comparative study demonstrates that the hybrid incremental model provides better error-based performance indices for detecting imbalance than a nonlinear regression model and an adaptive neural-fuzzy inference system model. The suitability of Mahanolobis normalization for hybrid incremental modeling is also demonstrated in this case study. The proposed strategy for imbalance detection is simple, fast, and non-intrusive, reducing the deterioration in the performance of ultra-high precision rotating machines due to vibrations.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

HER2-low and ultra-low breast cancer (BC) have been recently proposed as new subcategories of HER2 BC, re-considering the immunohistochemical negative score of 0, 1+ or score of 2+/in situ hybridization (ISH) negative phenotype. In the present review we have outlined the needed criteria to exactly distinguish HER2 low and ultra-low BC. Recent clinical trials have demonstrated significant clinical benefits of novel HER2 directing antibody-drug conjugates (ADCs) in treating these group sof tumors. In particular, Trastuzumab-deruxtecan (T-Dxd), a HER2-directing ADC has been recently approved by the U.S. Food and Drug Administration as the first targeted therapy to treat HER2-low BC. Furthermore, ongoing trials, such as the DESTINY-Breast06, are currently evaluating ADCs in patients with HER2-ultra low BC. Finally we hope that new guidelines may help to codify HER2 low and ultra-low BC, increasing our knowledge of tumor biology and improving a targetable new therapeutical treatment.